LM111-LM211-LM311 Voltage comparator with strobe Features Maximum input current: 150nA Maximum offset current: 20nA Differential input voltage range: 30V Power consumption:135mW at 15V Supply voltage: +5V to 15V Output current: 50mA N DIP8 (Plastic package) D SO-8 (Plastic micropackage) Description The LM111, LM211, LM311 are voltage comparators that have low input currents. Pin connections (top view) They are also designed to operate over a wide range of supply voltages: from standard 15V operational amplifier supplies down to the single +5V supply used for IC logic. Their output is compatible with RTL-DTL and TTL as well as MOS circuits and can switch voltages up to +50V at output currents as high as 50mA. Order codes Part number Temperature range LM211N Package Packing Marking DIP8 Tube LM211N SO-8 Tube or tape & reel 211 DIP8 Tube LM311 SO-8 Tube or Tape & reel 311 -40C, +105C LM211D/DT LM311N 0C, +70C LM311D/DT September 2006 Rev 4 1/14 www.st.com 14 Contents LM111-LM211-LM311 Contents 1 Schematic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Absolute maximum ratings & operating conditions . . . . . . . . . . . . . . . 4 3 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4 Typical application schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 5 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 6 2/14 5.1 DIP8 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 5.2 SO-8 package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 LM111-LM211-LM311 1 Schematic diagram Schematic diagram Figure 1. Schematic diagram 3/14 Absolute maximum ratings & operating conditions 2 LM111-LM211-LM311 Absolute maximum ratings & operating conditions Table 1. Absolute maximum ratings (AMR) Symbol Parameter Value Unit VCC Supply voltage 36 V Vid Differential input voltage 30 V 15 V Vi Input voltage (1) V(1-4) Ground to negative supply voltage 30 V V(7-4) Output to negative supply voltage LM111-LM211 LM311 50 40 V Output short-circuit duration 10 s VCC+ Voltage at strobe pin -5 V pd Power dissipation (2) DIP8 SO-8 1250 710 mW Tj Junction temperature +150 C -65 to +150 C Tstg Storage temperature range 1. This rating applies for 15V supplies. The positive input voltage limit is 30V above the negative. The negative input voltage is equal to the negative supply voltage or 30V below the positive supply, whichever is less. 2. Pd is calculated with Tamb = +25C, Tj = +150C and Rthja = 100C/W for the DIP8 package, and Rthja = 175C/W for the SO-8 package. Table 2. Operating conditions Symbol 4/14 Parameter VCC Supply voltage Toper Operating free-air temperature range LM111 LM211 LM311 Value Unit 5 to 15 V -55 to +125 -40 to +105 0 to +70 C LM111-LM211-LM311 Electrical characteristics 3 Electrical characteristics Table 3. VCC+ = 15V, Tamb = +25C (unless otherwise specified) LM111 - LM211 Symbol Parameter Unit Min. Vio Input offset voltage (1) RS 50k Tamb = +25C Tmin Tamb Tmax Iio Input offset current (1) Iib Input bias current (1) Avd Large signal voltage gain ICC+ ICC- Supply currents Vicm Input common mode voltage range Typ. Max. Min. 7.5 10 Tamb = +25C Tmin Tamb Tmax 4 10 20 6 50 70 nA Tamb = +25C Tmin Tamb Tmax 60 100 150 100 250 300 nA 40 Positive Negative Tmin Tamb Tmax 200 5.1 4.1 40 6 5 -14.5 +13.8 -14.7 +13 0.75 1.5 Tmin Tamb Tmax VCC+ +4.5V, VCC- = 0 IO = 8mA, Vi -6m Tamb = +25C Vi +5mV, VO = +35V High level output current tre Strobe current Response time (2) 200 5.1 4.1 V/mV 7.5 5 -14.5 +13.8 -14.7 +13 0.75 1.5 mA V V 0.23 0.4 0.23 0.2 nA 0.2 0.1 0.4 10 Tamb = +25C Vi +10mV, VO = +35V Tmin Tamb Tmax Vi +5mV, VO = +35V Istrobe mV 2 Tmin Tamb Tmax VCC+ +4.5V, VCC- = 0 IO = 8mA, Vi -10mV IOH Max. 3 4 Tamb = +25C, IO = 50mA, Vi -10mV Low level output voltage Typ. 0.7 Tamb = +25C, IO = 50mA, Vi -5mV VOL LM311 Conditions 0.5 50 nA A 3 3 mA 200 200 ns 1. The offset voltage, offset current and bias current specifications apply for any supply voltage from a single +5V supply up to 15V supplies. The offset voltages and offset currents given are the maximum values required to drive the output down to +1V or up to +14V with a 1mA load current. Thus, these parameters define an error band and take into account the worstcase of voltage gain and input impedance. 2. The response time specified is for a 100mV input step with 5mV overdrive. 5/14 Electrical characteristics 6/14 LM111-LM211-LM311 LM111-LM211-LM311 Electrical characteristics 7/14 Electrical characteristics 8/14 LM111-LM211-LM311 LM111-LM211-LM311 4 Typical application schematics Typical application schematics 9/14 Package mechanical data 5 LM111-LM211-LM311 Package mechanical data In order to meet environmental requirements, STMicroelectronics offers these devices in ECOPACK(R) packages. These packages have a Lead-free second level interconnect. The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an STMicroelectronics trademark. ECOPACK specifications are available at: www.st.com. 10/14 LM111-LM211-LM311 5.1 Package mechanical data DIP8 package Plastic DIP-8 MECHANICAL DATA mm. inch DIM. MIN. A TYP MAX. MIN. 3.3 0.7 B 1.39 1.65 0.055 B1 0.91 1.04 0.036 b1 MAX. 0.130 a1 b TYP. 0.028 0.5 0.38 0.041 0.020 0.5 D 0.065 0.015 0.020 9.8 0.386 E 8.8 0.346 e 2.54 0.100 e3 7.62 0.300 e4 7.62 0.300 F 7.1 0.280 I 4.8 0.189 L Z 3.3 0.44 0.130 1.6 0.017 0.063 P001F 11/14 Package mechanical data 5.2 LM111-LM211-LM311 SO-8 package SO-8 MECHANICAL DATA DIM. mm. MIN. TYP inch MAX. MIN. 0.053 TYP. MAX. A 1.35 1.75 0.069 A1 0.10 0.25 0.04 0.010 A2 1.10 1.65 0.043 0.065 B 0.33 0.51 0.013 0.020 C 0.19 0.25 0.007 0.010 D 4.80 5.00 0.189 0.197 E 3.80 4.00 0.150 0.157 e 1.27 0.050 H 5.80 6.20 0.228 0.244 h 0.25 0.50 0.010 0.020 L 0.40 1.27 0.016 0.050 k ddd 8 (max.) 0.1 0.04 0016023/C 12/14 LM111-LM211-LM311 6 Revision history Revision history Date Revision Changes 1-Jun-02 1 Initial release. 2-Jan-06 2 Table 3. on page 5 updated. Formatting changes throughout. 1-Mar-06 3 Pin connections updated on page 1. 26-Sep-06 4 Corrected description under title on cover page. 13/14 LM111-LM211-LM311 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER'S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. (c) 2006 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 14/14