ES1A - ES1G 1.0A SURFACE MOUNT SUPER-FAST RECTIFIER Features * * * * * * Glass Passivated Die Construction Super-Fast Recovery Time For High Efficiency Low Forward Voltage Drop and High Current Capability Surge Overload Rating to 30A Peak Ideally Suited for Automated Assembly Plastic Material: UL Flammability Classification Rating 94V-0 SMA B A * * * Min Max A 2.29 2.92 B 4.00 4.60 C 1.27 1.63 D 0.15 0.31 5.59 C Mechanical Data * * Dim D Case: Molded Plastic Terminals: Solder Plated Terminal - Solderable per MIL-STD-202, Method 208 Polarity: Cathode Band or Cathode Notch Marking: Type Number Weight: 0.064 grams (approx.) J H Maximum Ratings and Electrical Characteristics G E E 4.80 G 0.10 0.20 H 0.76 1.52 J 2.01 2.62 All Dimensions in mm @ TA = 25C unless otherwise specified Single phase, half wave, 60Hz, resistive or inductive load. For capacitive load, derate current by 20%. Characteristic Peak Repetitive Reverse Voltage Working Peak Reverse Voltage DC Blocking Voltage RMS Reverse Voltage Average Rectified Output Current @ TT = 110C Non-Repetitive Peak Forward Surge Current 8.3ms Single half sine-wave Superimposed on Rated Load (JEDEC Method) Forward Voltage Drop Symbol ES1A ES1B ES1C ES1D ES1G Unit VRRM VRWM VR 50 100 150 200 400 V VR(RMS) 35 70 105 140 280 V IO 1.0 A IFSM 30 A 3/4 1.25 @ IF = 0.6A @ IF = 1.0A VFM @ TA = 25C @ TA = 100C IRM 5.0 200 mA Reverse Recovery Time (Note 3) trr 20 ns Typical Junction Capacitance (Note 2) Cj 10 pF RqJT 40 K/W Tj, TSTG -65 to +150 C Peak Reverse Current at Rated DC Blocking Voltage Typical Thermal Resistance, Junction to Terminal (Note 1) Operating and Storage Temperature Range Notes: 0.90 0.98 V 1. Unit mounted on PC board with 5.0 mm2 (0.013 mm thick) copper pad as heat sink. 2. Measured at 1.0MHz and applied reverse voltage of 4.0V DC. 3. Measured with IF = 0.5A, IR = 1.0A, Irr = 0.25A. See figure 5. DS14001 Rev. G-2 1 of 2 ES1A - ES1G IF, INSTANTANEOUS FORWARD CURRENT (A) IO, AVERAGE RECTIFIED CURRENT (A) 1.5 1.0 0.5 0 25 50 75 100 125 150 175 10 ES1A - ES1D 0.1 Tj = 25C IF Pulse Width: 300 s 0.01 0 Single Half-Sine-Wave (JEDEC Method) 20 10 0 1 10 0.4 0.8 1.2 1.6 VF, INSTANTANEOUS FORWARD VOLTAGE (V) Fig. 2 Typical Forward Characteristics IR, INSTANTANEOUS REVERSE CURRENT (A) IFSM, PEAK FORWARD SURGE CURRENT (A) TT, TERMINAL TEMPERATURE (C) Fig. 1 Forward Current Derating Curve 30 ES1G 1.0 100 100 Tj = 100C 10 1.0 Tj = 25C 0.1 0 NUMBER OF CYCLES AT 60 Hz Fig. 3 Surge Current Derating Curve 40 80 120 PERCENT OF RATED PEAK REVERSE VOLTAGE (%) Fig. 4 Typical Reverse Characteristics trr 50 NI (Non-inductive) (-) 10 NI Device Under Test (+) +0.5A (-) 0A Pulse Generator (Note 2) 50V DC Approx 1.0 NI Oscilloscope (Note 1) -0.25A (+) Notes: 1. Rise Time = 7.0ns max. Input Impedance = 1.0M, 22pF. 2. Rise Time = 10ns max. Input Impedance = 50. -1.0A Set time base for 50/100 ns/cm Fig. 5 Reverse Recovery Time Characteristic and Test Circuit DS14001 Rev. G-2 2 of 2 ES1A - ES1G