ATMEGA168P-20MU - Atmel - Datasheet.Directory

Features

•High Performance, Low Power Atmel® AVR® 8-Bit Microcontroller

•Advanced RISC Architecture

– 131 Powerful Instructions – Most Single Clock Cycle Execution

– 32 x 8 General Purpose Working Registers

– Fully Static Operation

– Up to 20 MIPS Throughput at 20 MHz

– On-chip 2-cycle Multiplier

•High Endurance Non-volatile Memory Segments

– 4/8/16KBytes of In-System Self-Programmable Flash progam memory

– 256/512/512Bytes EEPROM

– 512/1K/1KBytes Internal SRAM

– Write/Erase Cycles: 10,000 Flash/100,000 EEPROM

– Data retention: 20 years at 85°C/100 years at 25°C(1)

– Optional Boot Code Section with Independent Lock Bits

In-System Programming by On-chip Boot Program

True Read-While-Write Operation

– Programming Lock for Software Security

•QTouch® library support

– Capacitive touch buttons, sliders and wheels

– QTouch and QMatrix acquisition

– Up to 64 sense channels

•Peripheral Features

– Two 8-bit Timer/Counters with Separate Prescaler and Compare Mode

– One 16-bit Timer/Counter with Separate Prescaler, Compare Mode, and Capture

Mode

– Real Time Counter with Separate Oscillator

– Six PWM Channels

– 8-channel 10-bit ADC in TQFP and QFN/MLF package

Temperature Measurement

– 6-channel 10-bit ADC in PDIP Package

Temperature Measurement

– Programmable Serial USART

– Master/Slave SPI Serial Interface

– Byte-oriented 2-wire Serial Interface (Philips I2C compatible)

– Programmable Watchdog Timer with Separate On-chip Oscillator

– On-chip Analog Comparator

– Interrupt and Wake-up on Pin Change

•Special Microcontroller Features

– Power-on Reset and Programmable Brown-out Detection

– Internal Calibrated Oscillator

– External and Internal Interrupt Sources

– Six Sleep Modes: Idle, ADC Noise Reduction, Power-save, Power-down, Standby,

and Extended Standby

•I/O and Packages

– 23 Programmable I/O Lines

– 28-pin PDIP, 32-lead TQFP, 28-pad QFN/MLF and 32-pad QFN/MLF

•Operating Voltage:

– 1.8 - 5.5V for ATmega48P/88P/168PV

– 2.7 - 5.5V for ATmega48P/88P/168P

•Temperature Range:

–-40

°C to 85°C

•Speed Grade:

– ATmega48P/88P/168PV: 0 - 4MHz @ 1.8 - 5.5V, 0 - 10MHz @ 2.7 - 5.5V

– ATmega48P/88P/168P: 0 - 10MHz @ 2.7 - 5.5V, 0 - 20MHz @ 4.5 - 5.5V

•Low Power Consumption at 1MHz, 1.8V, 25°C:

– Active Mode: 0.3mA

– Power-down Mode: 0.1µA

– Power-save Mode: 0.8µA (Including 32kHz RTC)

Note: 1. See ”Data Retention” on page 8 for details.

8-bit Atmel

Microcontroller

with 4/8/16K

Bytes In-System

Programmable

Flash

ATmega48P/V

ATmega88P/V

ATmega168P/V

Summary

Rev. 8025MS–AVR–6/11

8025MS–AVR–6/11

ATmega48P/88P/168P

1. Pin Configurations

Figure 1-1. Pinout ATmega48P/88P/168P

(PCINT19/OC2B/INT1) PD3

(PCINT20/XCK/T0) PD4

GND

VCC

GND

VCC

(PCINT6/XTAL1/TOSC1) PB6

(PCINT7/XTAL2/TOSC2) PB7

PC1 (ADC1/PCINT9)

PC0 (ADC0/PCINT8)

ADC7

GND

AREF

ADC6

AVCC

PB5 (SCK/PCINT5)

(PCINT21/OC0B/T1) PD5

(PCINT22/OC0A/AIN0) PD6

(PCINT23/AIN1) PD7

(PCINT0/CLKO/ICP1) PB0

(PCINT1/OC1A) PB1

(PCINT2/SS/OC1B) PB2

(PCINT3/OC2A/MOSI) PB3

(PCINT4/MISO) PB4

PD2 (INT0/PCINT18)

PD1 (TXD/PCINT17)

PD0 (RXD/PCINT16)

PC6 (RESET/PCINT14)

PC5 (ADC5/SCL/PCINT13)

PC4 (ADC4/SDA/PCINT12)

PC3 (ADC3/PCINT11)

PC2 (ADC2/PCINT10)

TQFP Top View

(PCINT14/RESET) PC6

(PCINT16/RXD) PD0

(PCINT17/TXD) PD1

(PCINT18/INT0) PD2

(PCINT19/OC2B/INT1) PD3

(PCINT20/XCK/T0) PD4

VCC

GND

(PCINT6/XTAL1/TOSC1) PB6

(PCINT7/XTAL2/TOSC2) PB7

(PCINT21/OC0B/T1) PD5

(PCINT22/OC0A/AIN0) PD6

(PCINT23/AIN1) PD7

(PCINT0/CLKO/ICP1) PB0

PC5 (ADC5/SCL/PCINT13)

PC4 (ADC4/SDA/PCINT12)

PC3 (ADC3/PCINT11)

PC2 (ADC2/PCINT10)

PC1 (ADC1/PCINT9)

PC0 (ADC0/PCINT8)

GND

AREF

AVCC

PB5 (SCK/PCINT5)

PB4 (MISO/PCINT4)

PB3 (MOSI/OC2A/PCINT3)

PB2 (SS/OC1B/PCINT2)

PB1 (OC1A/PCINT1)

PDIP

32 MLF Top View

(PCINT19/OC2B/INT1) PD3

(PCINT20/XCK/T0) PD4

GND

VCC

GND

VCC

(PCINT6/XTAL1/TOSC1) PB6

(PCINT7/XTAL2/TOSC2) PB7

PC1 (ADC1/PCINT9)

PC0 (ADC0/PCINT8)

ADC7

GND

AREF

ADC6

AVCC

PB5 (SCK/PCINT5)

(PCINT21/OC0B/T1) PD5

(PCINT22/OC0A/AIN0) PD6

(PCINT23/AIN1) PD7

(PCINT0/CLKO/ICP1) PB0

(PCINT1/OC1A) PB1

(PCINT2/SS/OC1B) PB2

(PCINT3/OC2A/MOSI) PB3

(PCINT4/MISO) PB4

PD2 (INT0/PCINT18)

PD1 (TXD/PCINT17)

PD0 (RXD/PCINT16)

PC6 (RESET/PCINT14)

PC5 (ADC5/SCL/PCINT13)

PC4 (ADC4/SDA/PCINT12)

PC3 (ADC3/PCINT11)

PC2 (ADC2/PCINT10)

NOTE: Bottom pad should be soldered to ground.

28 MLF Top View

(PCINT19/OC2B/INT1) PD3

(PCINT20/XCK/T0) PD4

VCC

GND

(PCINT6/XTAL1/TOSC1) PB6

(PCINT7/XTAL2/TOSC2) PB7

(PCINT21/OC0B/T1) PD5

(PCINT22/OC0A/AIN0) PD6

(PCINT23/AIN1) PD7

(PCINT0/CLKO/ICP1) PB0

(PCINT1/OC1A) PB1

(PCINT2/SS/OC1B) PB2

(PCINT3/OC2A/MOSI) PB3

(PCINT4/MISO) PB4

PD2 (INT0/PCINT18)

PD1 (TXD/PCINT17)

PD0 (RXD/PCINT16)

PC6 (RESET/PCINT14)

PC5 (ADC5/SCL/PCINT13)

PC4 (ADC4/SDA/PCINT12)

PC3 (ADC3/PCINT11)

PC2 (ADC2/PCINT10)

PC1 (ADC1/PCINT9)

PC0 (ADC0/PCINT8)

GND

AREF

AVCC

PB5 (SCK/PCINT5)

NOTE: Bottom pad should be soldered to ground.

8025MS–AVR–6/11

ATmega48P/88P/168P

1.1 Pin Descriptions

1.1.1 VCC

Digital supply voltage.

1.1.2 GND

Ground.

1.1.3 Port B (PB7:0) XTAL1/XTAL2/TOSC1/TOSC2

Port B is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The

Port B output buffers have symmetrical drive characteristics with both high sink and source

capability. As inputs, Port B pins that are externally pulled low will source current if the pull-up

resistors are activated. The Port B pins are tri-stated when a reset condition becomes active,

even if the clock is not running.

Depending on the clock selection fuse settings, PB6 can be used as input to the inverting Oscil-

lator amplifier and input to the internal clock operating circuit.

Depending on the clock selection fuse settings, PB7 can be used as output from the inverting

Oscillator amplifier.

If the Internal Calibrated RC Oscillator is used as chip clock source, PB7:6 is used as TOSC2:1

input for the Asynchronous Timer/Counter2 if the AS2 bit in ASSR is set.

The various special features of Port B are elaborated in ”Alternate Functions of Port B” on page

80 and ”System Clock and Clock Options” on page 27.

1.1.4 Port C (PC5:0)

Port C is a 7-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The

PC5:0 output buffers have symmetrical drive characteristics with both high sink and source

capability. As inputs, Port C pins that are externally pulled low will source current if the pull-up

resistors are activated. The Port C pins are tri-stated when a reset condition becomes active,

even if the clock is not running.

1.1.5 PC6/RESET

If the RSTDISBL Fuse is programmed, PC6 is used as an I/O pin. Note that the electrical char-

acteristics of PC6 differ from those of the other pins of Port C.

If the RSTDISBL Fuse is unprogrammed, PC6 is used as a Reset input. A low level on this pin

for longer than the minimum pulse length will generate a Reset, even if the clock is not running.

The minimum pulse length is given in Table 29-3 on page 314. Shorter pulses are not guaran-

teed to generate a Reset.

The various special features of Port C are elaborated in ”Alternate Functions of Port C” on page

83.

1.1.6 Port D (PD7:0)

Port D is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The

Port D output buffers have symmetrical drive characteristics with both high sink and source

capability. As inputs, Port D pins that are externally pulled low will source current if the pull-up

resistors are activated. The Port D pins are tri-stated when a reset condition becomes active,

even if the clock is not running.

8025MS–AVR–6/11

ATmega48P/88P/168P

The various special features of Port D are elaborated in ”Alternate Functions of Port D” on page

86.

1.1.7 AVCC

AVCC is the supply voltage pin for the A/D Converter, PC3:0, and ADC7:6. It should be externally

connected to VCC, even if the ADC is not used. If the ADC is used, it should be connected to VCC

through a low-pass filter. Note that PC6:4 use digital supply voltage, VCC.

1.1.8 AREF

AREF is the analog reference pin for the A/D Converter.

1.1.9 ADC7:6 (TQFP and QFN/MLF Package Only)

In the TQFP and QFN/MLF package, ADC7:6 serve as analog inputs to the A/D converter.

These pins are powered from the analog supply and serve as 10-bit ADC channels.

2. Overview

The ATmega48P/88P/168P is a low-power CMOS 8-bit microcontroller based on the AVR

enhanced RISC architecture. By executing powerful instructions in a single clock cycle, the

ATmega48P/88P/168P achieves throughputs approaching 1 MIPS per MHz allowing the system

designer to optimize power consumption versus processing speed.

8025MS–AVR–6/11

ATmega48P/88P/168P

2.1 Block Diagram

Figure 2-1. Block Diagram

PORT C (7)PORT B (8)PORT D (8)

USART 0

8bit T/C 2

16bit T/C 18bit T/C 0 A/D Conv.

Internal

Bandgap

Analog

Comp.

SPI TWI

SRAMFlash

EEPROM

Watchdog

Oscillator

Watchdog

Timer

Oscillator

Circuits /

Clock

Generation

Power

Supervision

POR / BOD &

RESET

VCC

GND

PROGRAM

LOGIC

debugWIRE

GND

AREF

AVCC

DATA B U S

ADC[6..7]PC[0..6]PB[0..7]PD[0..7]

RESET

XTAL[1..2]

CPU

8025MS–AVR–6/11

ATmega48P/88P/168P

The AVR core combines a rich instruction set with 32 general purpose working registers. All the

32 registers are directly connected to the Arithmetic Logic Unit (ALU), allowing two independent

registers to be accessed in one single instruction executed in one clock cycle. The resulting

architecture is more code efficient while achieving throughputs up to ten times faster than con-

ventional CISC microcontrollers.

The ATmega48P/88P/168P provides the following features: 4K/8K/16Kbytes of In-System Pro-

grammable Flash with Read-While-Write capabilities, 256/512/512bytes EEPROM,

512/1K/1Kbytes SRAM, 23 general purpose I/O lines, 32 general purpose working registers,

three flexible Timer/Counters with compare modes, internal and external interrupts, a serial pro-

grammable USART, a byte-oriented, 2-wire Serial Interface, an SPI serial port, a 6-channel 10-

bit ADC (8 channels in TQFP and QFN/MLF packages), a programmable Watchdog Timer with

internal Oscillator, and five software selectable power saving modes. The Idle mode stops the

CPU while allowing the SRAM, Timer/Counters, USART, 2-wire Serial Interface, SPI port, and

interrupt system to continue functioning. The Power-down mode saves the register contents but

freezes the Oscillator, disabling all other chip functions until the next interrupt or hardware reset.

In Power-save mode, the asynchronous timer continues to run, allowing the user to maintain a

timer base while the rest of the device is sleeping. The ADC Noise Reduction mode stops the

CPU and all I/O modules except asynchronous timer and ADC, to minimize switching noise dur-

ing ADC conversions. In Standby mode, the crystal/resonator Oscillator is running while the rest

of the device is sleeping. This allows very fast start-up combined with low power consumption.

Atmel offers the QTouch® library for embedding capacitive touch buttons, sliders and wheels

functionality into AVR microcontrollers. The patented charge-transfer signal acquisition offers

robust sensing and includes fully debounced reporting of touch keys and includes Adjacent Key

Suppression® (AKS™) technology for unambiguous detection of key events. The easy-to-use

QTouch Suite toolchain allows you to explore, develop and debug your own touch applications.

The device is manufactured using Atmel’s high density non-volatile memory technology. The

On-chip ISP Flash allows the program memory to be reprogrammed In-System through an SPI

serial interface, by a conventional non-volatile memory programmer, or by an On-chip Boot pro-

gram running on the AVR core. The Boot program can use any interface to download the

application program in the Application Flash memory. Software in the Boot Flash section will

continue to run while the Application Flash section is updated, providing true Read-While-Write

operation. By combining an 8-bit RISC CPU with In-System Self-Programmable Flash on a

monolithic chip, the Atmel ATmega48P/88P/168P is a powerful microcontroller that provides a

highly flexible and cost effective solution to many embedded control applications.

The ATmega48P/88P/168P AVR is supported with a full suite of program and system develop-

ment tools including: C Compilers, Macro Assemblers, Program Debugger/Simulators, In-Circuit

Emulators, and Evaluation kits.

8025MS–AVR–6/11

ATmega48P/88P/168P

2.2 Comparison Between ATmega48P, ATmega88P and ATmega168P

The ATmega48P, ATmega88P and ATmega168P differ only in memory sizes, boot loader sup-

port, and interrupt vector sizes. Table 2-1 summarizes the different memory and interrupt vector

sizes for the three devices.

ATmega88P and ATmega168P support a real Read-While-Write Self-Programming mechanism.

There is a separate Boot Loader Section, and the SPM instruction can only execute from there.

In ATmega48P, there is no Read-While-Write support and no separate Boot Loader Section.

The SPM instruction can execute from the entire Flash.

Table 2-1. Memory Size Summary

Device Flash EEPROM RAM Interrupt Vector Size

ATmega48P 4KBytes 256Bytes 512Bytes 1 instruction word/vector

ATmega88P 8KBytes 512Bytes 1KBytes 1 instruction word/vector

ATmega168P 16KBytes 512Bytes 1KBytes 2 instruction words/vector

8025MS–AVR–6/11

ATmega48P/88P/168P

3. Resources

A comprehensive set of development tools, application notes and datasheets are available for

download on http://www.atmel.com/avr.

Note: 1.

4. Data Retention

Reliability Qualification results show that the projected data retention failure rate is much less

than 1 PPM over 20 years at 85°C or 100 years at 25°C.

5. About Code Examples

This documentation contains simple code examples that briefly show how to use various parts of

the device. These code examples assume that the part specific header file is included before

compilation. Be aware that not all C compiler vendors include bit definitions in the header files

and interrupt handling in C is compiler dependent. Please confirm with the C compiler documen-

tation for more details.

For I/O Registers located in extended I/O map, “IN”, “OUT”, “SBIS”, “SBIC”, “CBI”, and “SBI”

instructions must be replaced with instructions that allow access to extended I/O. Typically

“LDS” and “STS” combined with “SBRS”, “SBRC”, “SBR”, and “CBR”.

6. Capacitive touch sensing

The Atmel® QTouch® Library provides a simple to use solution to realize touch sensitive inter-

faces on most Atmel AVR® microcontrollers. The QTouch Library includes support for the

QTouch and QMatrix® acquisition methods.

Touch sensing can be added to any application by linking the appropriate Atmel QTouch Library

for the AVR Microcontroller. This is done by using a simple set of APIs to define the touch chan-

nels and sensors, and then calling the touch sensing API’s to retrieve the channel information

and determine the touch sensor states.

The QTouch Library is FREE and downloadable from the Atmel website at the following location:

www.atmel.com/qtouchlibrary. For implementation details and other information, refer to the

Atmel QTouch Library User Guide - also available for download from the Atmel website.

8025MS–AVR–6/11

ATmega48P/88P/168P

7. Register Summary

Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Page

(0xFF) Reserved – – – – – – – –

(0xFE) Reserved – – – – – – – –

(0xFD) Reserved – – – – – – – –

(0xFC) Reserved – – – – – – – –

(0xFB) Reserved – – – – – – – –

(0xFA) Reserved – – – – – – – –

(0xF9) Reserved – – – – – – – –

(0xF8) Reserved – – – – – – – –

(0xF7) Reserved – – – – – – – –

(0xF6) Reserved – – – – – – – –

(0xF5) Reserved – – – – – – – –

(0xF4) Reserved – – – – – – – –

(0xF3) Reserved – – – – – – – –

(0xF2) Reserved – – – – – – – –

(0xF1) Reserved – – – – – – – –

(0xF0) Reserved – – – – – – – –

(0xEF) Reserved – – – – – – – –

(0xEE) Reserved – – – – – – – –

(0xED) Reserved – – – – – – – –

(0xEC) Reserved – – – – – – – –

(0xEB) Reserved – – – – – – – –

(0xEA) Reserved – – – – – – – –

(0xE9) Reserved – – – – – – – –

(0xE8) Reserved – – – – – – – –

(0xE7) Reserved – – – – – – – –

(0xE6) Reserved – – – – – – – –

(0xE5) Reserved – – – – – – – –

(0xE4) Reserved – – – – – – – –

(0xE3) Reserved – – – – – – – –

(0xE2) Reserved – – – – – – – –

(0xE1) Reserved – – – – – – – –

(0xE0) Reserved – – – – – – – –

(0xDF) Reserved – – – – – – – –

(0xDE) Reserved – – – – – – – –

(0xDD) Reserved – – – – – – – –

(0xDC) Reserved – – – – – – – –

(0xDB) Reserved – – – – – – – –

(0xDA) Reserved – – – – – – – –

(0xD9) Reserved – – – – – – – –

(0xD8) Reserved – – – – – – – –

(0xD7) Reserved – – – – – – – –

(0xD6) Reserved – – – – – – – –

(0xD5) Reserved – – – – – – – –

(0xD4) Reserved – – – – – – – –

(0xD3) Reserved – – – – – – – –

(0xD2) Reserved – – – – – – – –

(0xD1) Reserved – – – – – – – –

(0xD0) Reserved – – – – – – – –

(0xCF) Reserved – – – – – – – –

(0xCE) Reserved – – – – – – – –

(0xCD) Reserved – – – – – – – –

(0xCC) Reserved – – – – – – – –

(0xCB) Reserved – – – – – – – –

(0xCA) Reserved – – – – – – – –

(0xC9) Reserved – – – – – – – –

(0xC8) Reserved – – – – – – – –

(0xC7) Reserved – – – – – – – –

(0xC6) UDR0 USART I/O Data Register 193

(0xC5) UBRR0H USART Baud Rate Register High 197

(0xC4) UBRR0L USART Baud Rate Register Low 197

(0xC3) Reserved – – – – – – – –

(0xC2) UCSR0C UMSEL01 UMSEL00 UPM01 UPM00 USBS0 UCSZ01 /UDORD0 UCSZ00 / UCPHA0 UCPOL0 195/210

8025MS–AVR–6/11

ATmega48P/88P/168P

(0xC1) UCSR0B RXCIE0 TXCIE0 UDRIE0 RXEN0 TXEN0 UCSZ02 RXB80 TXB80 194

(0xC0) UCSR0A RXC0 TXC0 UDRE0 FE0 DOR0 UPE0 U2X0 MPCM0 193

(0xBF) Reserved – – – – – – – –

(0xBE) Reserved – – – – – – – –

(0xBD) TWAMR TWAM6 TWAM5 TWAM4 TWAM3 TWAM2 TWAM1 TWAM0 –242

(0xBC) TWCR TWINT TWEA TWSTA TWSTO TWWC TWEN –TWIE 239

(0xBB) TWDR 2-wire Serial Interface Data Register 241

(0xBA) TWAR TWA6 TWA5 TWA4 TWA3 TWA2 TWA1 TWA0 TWGCE 242

(0xB9) TWSR TWS7 TWS6 TWS5 TWS4 TWS3 –TWPS1TWPS0 241

(0xB8) TWBR 2-wire Serial Interface Bit Rate Register 239

(0xB7) Reserved – – – – – – –

(0xB6) ASSR – EXCLK AS2 TCN2UB OCR2AUB OCR2BUB TCR2AUB TCR2BUB 162

(0xB5) Reserved – – – – – – – –

(0xB4) OCR2B Timer/Counter2 Output Compare Register B 160

(0xB3) OCR2A Timer/Counter2 Output Compare Register A 160

(0xB2) TCNT2 Timer/Counter2 (8-bit) 160

(0xB1) TCCR2B FOC2A FOC2B –– WGM22 CS22 CS21 CS20 159

(0xB0) TCCR2A COM2A1 COM2A0 COM2B1 COM2B0 ––WGM21WGM20 156

(0xAF) Reserved – – – – – – – –

(0xAE) Reserved – – – – – – – –

(0xAD) Reserved – – – – – – – –

(0xAC) Reserved – – – – – – – –

(0xAB) Reserved – – – – – – – –

(0xAA) Reserved – – – – – – – –

(0xA9) Reserved – – – – – – – –

(0xA8) Reserved – – – – – – – –

(0xA7) Reserved – – – – – – – –

(0xA6) Reserved – – – – – – – –

(0xA5) Reserved – – – – – – – –

(0xA4) Reserved – – – – – – – –

(0xA3) Reserved – – – – – – – –

(0xA2) Reserved – – – – – – – –

(0xA1) Reserved – – – – – – – –

(0xA0) Reserved – – – – – – – –

(0x9F) Reserved – – – – – – – –

(0x9E) Reserved – – – – – – – –

(0x9D) Reserved – – – – – – – –

(0x9C) Reserved – – – – – – – –

(0x9B) Reserved – – – – – – – –

(0x9A) Reserved – – – – – – – –

(0x99) Reserved – – – – – – – –

(0x98) Reserved – – – – – – – –

(0x97) Reserved – – – – – – – –

(0x96) Reserved – – – – – – – –

(0x95) Reserved – – – – – – – –

(0x94) Reserved – – – – – – – –

(0x93) Reserved – – – – – – – –

(0x92) Reserved – – – – – – – –

(0x91) Reserved – – – – – – – –

(0x90) Reserved – – – – – – – –

(0x8F) Reserved – – – – – – – –

(0x8E) Reserved – – – – – – – –

(0x8D) Reserved – – – – – – – –

(0x8C) Reserved – – – – – – – –

(0x8B) OCR1BH Timer/Counter1 - Output Compare Register B High Byte 136

(0x8A) OCR1BL Timer/Counter1 - Output Compare Register B Low Byte 136

(0x89) OCR1AH Timer/Counter1 - Output Compare Register A High Byte 136

(0x88) OCR1AL Timer/Counter1 - Output Compare Register A Low Byte 136

(0x87) ICR1H Timer/Counter1 - Input Capture Register High Byte 137

(0x86) ICR1L Timer/Counter1 - Input Capture Register Low Byte 137

(0x85) TCNT1H Timer/Counter1 - Counter Register High Byte 136

(0x84) TCNT1L Timer/Counter1 - Counter Register Low Byte 136

(0x83) Reserved – – – – – – – –

(0x82) TCCR1C FOC1A FOC1B – – – – – –135

(0x81) TCCR1B ICNC1 ICES1 – WGM13 WGM12 CS12 CS11 CS10 134

(0x80) TCCR1A COM1A1 COM1A0 COM1B1 COM1B0 ––WGM11WGM10 132

Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Page

8025MS–AVR–6/11

ATmega48P/88P/168P

(0x7F) DIDR1 – – – – – –AIN1DAIN0D 247

(0x7E) DIDR0 –– ADC5D ADC4D ADC3D ADC2D ADC1D ADC0D 264

(0x7D) Reserved – – – – – – – –

(0x7C) ADMUX REFS1 REFS0 ADLAR – MUX3 MUX2 MUX1 MUX0 260

(0x7B) ADCSRB –ACME – – – ADTS2 ADTS1 ADTS0 263

(0x7A) ADCSRA ADEN ADSC ADATE ADIF ADIE ADPS2 ADPS1 ADPS0 261

(0x79) ADCH ADC Data Register High byte 263

(0x78) ADCL ADC Data Register Low byte 263

(0x77) Reserved – – – – – – – –

(0x76) Reserved – – – – – – – –

(0x75) Reserved – – – – – – – –

(0x74) Reserved – – – – – – – –

(0x73) Reserved – – – – – – – –

(0x72) Reserved – – – – – – – –

(0x71) Reserved – – – – – – – –

(0x70) TIMSK2 – – – – – OCIE2B OCIE2A TOIE2 161

(0x6F) TIMSK1 ––ICIE1 –– OCIE1B OCIE1A TOIE1 137

(0x6E) TIMSK0 – – – – – OCIE0B OCIE0A TOIE0 109

(0x6D) PCMSK2 PCINT23 PCINT22 PCINT21 PCINT20 PCINT19 PCINT18 PCINT17 PCINT16 72

(0x6C) PCMSK1 – PCINT14 PCINT13 PCINT12 PCINT11 PCINT10 PCINT9 PCINT8 72

(0x6B) PCMSK0 PCINT7 PCINT6 PCINT5 PCINT4 PCINT3 PCINT2 PCINT1 PCINT0 72

(0x6A) Reserved – – – – – – – –

(0x69) EICRA – – – –ISC11ISC10ISC01ISC00 69

(0x68) PCICR – – – – – PCIE2 PCIE1 PCIE0

(0x67) Reserved – – – – – – – –

(0x66) OSCCAL Oscillator Calibration Register 38

(0x65) Reserved – – – – – – – –

(0x64) PRR PRTWI PRTIM2 PRTIM0 – PRTIM1 PRSPI PRUSART0 PRADC 43

(0x63) Reserved – – – – – – – –

(0x62) Reserved – – – – – – – –

(0x61) CLKPR CLKPCE – – – CLKPS3 CLKPS2 CLKPS1 CLKPS0 38

(0x60) WDTCSR WDIF WDIE WDP3 WDCE WDE WDP2 WDP1 WDP0 55

0x3F (0x5F) SREG I T H S V N Z C 10

0x3E (0x5E) SPH – – – – – (SP10) 5. SP9 SP8 13

0x3D (0x5D) SPL SP7 SP6 SP5 SP4 SP3 SP2 SP1 SP0 13

0x3C (0x5C) Reserved – – – – – – – –

0x3B (0x5B) Reserved – – – – – – – –

0x3A (0x5A) Reserved – – – – – – – –

0x39 (0x59) Reserved – – – – – – – –

0x38 (0x58) Reserved – – – – – – – –

0x37 (0x57) SPMCSR SPMIE (RWWSB)5. – (RWWSRE)5. BLBSET PGWRT PGERS SELFPRGEN 289

0x36 (0x56) Reserved – – – – – – – –

0x35 (0x55) MCUCR – BODS BODSE PUD –– IVSEL IVCE 45/66/90

0x34 (0x54) MCUSR – – – – WDRF BORF EXTRF PORF 55

0x33 (0x53) SMCR – – – –SM2SM1SM0SE 41

0x32 (0x52) Reserved – – – – – – – –

0x31 (0x51) Reserved – – – – – – – –

0x30 (0x50) ACSR ACD ACBG ACO ACI ACIE ACIC ACIS1 ACIS0 245

0x2F (0x4F) Reserved – – – – – – – –

0x2E (0x4E) SPDR SPI Data Register 173

0x2D (0x4D) SPSR SPIF WCOL – – – – – SPI2X 172

0x2C (0x4C) SPCR SPIE SPE DORD MSTR CPOL CPHA SPR1 SPR0 171

0x2B (0x4B) GPIOR2 General Purpose I/O Register 2 26

0x2A (0x4A) GPIOR1 General Purpose I/O Register 1 26

0x29 (0x49) Reserved – – – – – – – –

0x28 (0x48) OCR0B Timer/Counter0 Output Compare Register B

0x27 (0x47) OCR0A Timer/Counter0 Output Compare Register A

0x26 (0x46) TCNT0 Timer/Counter0 (8-bit)

0x25 (0x45) TCCR0B FOC0A FOC0B –– WGM02 CS02 CS01 CS00

0x24 (0x44) TCCR0A COM0A1 COM0A0 COM0B1 COM0B0 ––WGM01WGM00

0x23 (0x43) GTCCR TSM – – – – – PSRASY PSRSYNC 141/163

0x22 (0x42) EEARH (EEPROM Address Register High Byte) 5. 22

0x21 (0x41) EEARL EEPROM Address Register Low Byte 22

0x20 (0x40) EEDR EEPROM Data Register 22

0x1F (0x3F) EECR –– EEPM1 EEPM0 EERIE EEMPE EEPE EERE 22

0x1E (0x3E) GPIOR0 General Purpose I/O Register 0 26

Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Page

8025MS–AVR–6/11

ATmega48P/88P/168P

Note: 1. For compatibility with future devices, reserved bits should be written to zero if accessed. Reserved I/O memory addresses

should never be written.

2. I/O Registers within the address range 0x00 - 0x1F are directly bit-accessible using the SBI and CBI instructions. In these

registers, the value of single bits can be checked by using the SBIS and SBIC instructions.

3. Some of the Status Flags are cleared by writing a logical one to them. Note that, unlike most other AVRs, the CBI and SBI

instructions will only operate on the specified bit, and can therefore be used on registers containing such Status Flags. The

CBI and SBI instructions work with registers 0x00 to 0x1F only.

4. When using the I/O specific commands IN and OUT, the I/O addresses 0x00 - 0x3F must be used. When addressing I/O

Registers as data space using LD and ST instructions, 0x20 must be added to these addresses. The ATmega48P/88P/168P

is a complex microcontroller with more peripheral units than can be supported within the 64 location reserved in Opcode for

the IN and OUT instructions. For the Extended I/O space from 0x60 - 0xFF in SRAM, only the ST/STS/STD and

LD/LDS/LDD instructions can be used.

5. Only valid for ATmega88P/168P.

0x1D (0x3D) EIMSK – – – – – –INT1INT0 70

0x1C (0x3C) EIFR – – – – – – INTF1 INTF0 70

0x1B (0x3B) PCIFR – – – – – PCIF2 PCIF1 PCIF0

0x1A (0x3A) Reserved – – – – – – – –

0x19 (0x39) Reserved – – – – – – – –

0x18 (0x38) Reserved – – – – – – – –

0x17 (0x37) TIFR2 – – – – – OCF2B OCF2A TOV2 161

0x16 (0x36) TIFR1 ––ICF1 –– OCF1B OCF1A TOV1 138

0x15 (0x35) TIFR0 – – – – – OCF0B OCF0A TOV0

0x14 (0x34) Reserved – – – – – – – –

0x13 (0x33) Reserved – – – – – – – –

0x12 (0x32) Reserved – – – – – – – –

0x11 (0x31) Reserved – – – – – – – –

0x10 (0x30) Reserved – – – – – – – –

0x0F (0x2F) Reserved – – – – – – – –

0x0E (0x2E) Reserved – – – – – – – –

0x0D (0x2D) Reserved – – – – – – – –

0x0C (0x2C) Reserved – – – – – – – –

0x0B (0x2B) PORTD PORTD7 PORTD6 PORTD5 PORTD4 PORTD3 PORTD2 PORTD1 PORTD0 91

0x0A (0x2A) DDRD DDD7 DDD6 DDD5 DDD4 DDD3 DDD2 DDD1 DDD0 91

0x09 (0x29) PIND PIND7 PIND6 PIND5 PIND4 PIND3 PIND2 PIND1 PIND0 91

0x08 (0x28) PORTC – PORTC6 PORTC5 PORTC4 PORTC3 PORTC2 PORTC1 PORTC0 90

0x07 (0x27) DDRC – DDC6 DDC5 DDC4 DDC3 DDC2 DDC1 DDC0 90

0x06 (0x26) PINC – PINC6 PINC5 PINC4 PINC3 PINC2 PINC1 PINC0 90

0x05 (0x25) PORTB PORTB7 PORTB6 PORTB5 PORTB4 PORTB3 PORTB2 PORTB1 PORTB0 90

0x04 (0x24) DDRB DDB7 DDB6 DDB5 DDB4 DDB3 DDB2 DDB1 DDB0 90

0x03 (0x23) PINB PINB7 PINB6 PINB5 PINB4 PINB3 PINB2 PINB1 PINB0 90

0x02 (0x22) Reserved – – – – – – – –

0x01 (0x21) Reserved – – – – – – – –

0x0 (0x20) Reserved – – – – – – – –

Address Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Page

8025MS–AVR–6/11

ATmega48P/88P/168P

8. Instruction Set Summary

Mnemonics Operands Description Operation Flags #Clocks

ARITHMETIC AND LOGIC INSTRUCTIONS

ADD Rd, Rr Add two Registers Rd ← Rd + Rr Z,C,N,V,H 1

ADC Rd, Rr Add with Carry two Registers Rd ← Rd + Rr + C Z,C,N,V,H 1

ADIW Rdl,K Add Immediate to Word Rdh:Rdl ← Rdh:Rdl + K Z,C,N,V,S 2

SUB Rd, Rr Subtract two Registers Rd ← Rd - Rr Z,C,N,V,H 1

SUBI Rd, K Subtract Constant from Register Rd ← Rd - K Z,C,N,V,H 1

SBC Rd, Rr Subtract with Carry two Registers Rd ← Rd - Rr - C Z,C,N,V,H 1

SBCI Rd, K Subtract with Carry Constant from Reg. Rd ← Rd - K - C Z,C,N,V,H 1

SBIW Rdl,K Subtract Immediate from Word Rdh:Rdl ← Rdh:Rdl - K Z,C,N,V,S 2

AND Rd, Rr Logical AND Registers Rd ← Rd • Rr Z,N,V 1

ANDI Rd, K Logical AND Register and Constant Rd ← Rd • K Z,N,V 1

OR Rd, Rr Logical OR Registers Rd ← Rd v Rr Z,N,V 1

ORI Rd, K Logical OR Register and Constant Rd ← Rd v K Z,N,V 1

EOR Rd, Rr Exclusive OR Registers Rd ← Rd ⊕ Rr Z,N,V 1

COM Rd One’s Complement Rd ← 0xFF − Rd Z,C,N,V 1

NEG Rd Two’s Complement Rd ← 0x00 − Rd Z,C,N,V,H 1

SBR Rd,K Set Bit(s) in Register Rd ← Rd v K Z,N,V 1

CBR Rd,K Clear Bit(s) in Register Rd ← Rd • (0xFF - K) Z,N,V 1

INC Rd Increment Rd ← Rd + 1 Z,N,V 1

DEC Rd Decrement Rd ← Rd − 1 Z,N,V 1

TST Rd Test for Zero or Minus Rd ← Rd • Rd Z,N,V 1

CLR Rd Clear Register Rd ← Rd ⊕ Rd Z,N,V 1

SER Rd Set Register Rd ← 0xFF None 1

MUL Rd, Rr Multiply Unsigned R1:R0 ← Rd x Rr Z,C 2

MULS Rd, Rr Multiply Signed R1:R0 ← Rd x Rr Z,C 2

MULSU Rd, Rr Multiply Signed with Unsigned R1:R0 ← Rd x Rr Z,C 2

FMUL Rd, Rr Fractional Multiply Unsigned R1:R0 ← (Rd x Rr) << 1 Z,C 2

FMULS Rd, Rr Fractional Multiply Signed R1:R0 ← (Rd x Rr) << 1 Z,C 2

FMULSU Rd, Rr Fractional Multiply Signed with Unsigned R1:R0 ← (Rd x Rr) << 1 Z,C 2

BRANCH INSTRUCTIONS

RJMP k Relative Jump PC ← PC + k + 1 None 2

IJMP Indirect Jump to (Z) PC ← Z None 2

JMP(1) k Direct Jump PC ← kNone3

RCALL k Relative Subroutine Call PC ← PC + k + 1 None 3

ICALL Indirect Call to (Z) PC ← ZNone3

CALL(1) k Direct Subroutine Call PC ← kNone4

RET Subroutine Return PC ← STACK None 4

RETI Interrupt Return PC ← STACK I 4

CPSE Rd,Rr Compare, Skip if Equal if (Rd = Rr) PC ← PC + 2 or 3 None 1/2/3

CP Rd,Rr Compare Rd − Rr Z, N,V,C,H 1

CPC Rd,Rr Compare with Carry Rd − Rr − C Z, N,V,C,H 1

CPI Rd,K Compare Register with Immediate Rd − K Z, N,V,C,H 1

SBRC Rr, b Skip if Bit in Register Cleared if (Rr(b)=0) PC ← PC + 2 or 3 None 1/2/3

SBRS Rr, b Skip if Bit in Register is Set if (Rr(b)=1) PC ← PC + 2 or 3 None 1/2/3

SBIC P, b Skip if Bit in I/O Register Cleared if (P(b)=0) PC ← PC + 2 or 3 None 1/2/3

SBIS P, b Skip if Bit in I/O Register is Set if (P(b)=1) PC ← PC + 2 or 3 None 1/2/3

BRBS s, k Branch if Status Flag Set if (SREG(s) = 1) then PC←PC+k + 1 None 1/2

BRBC s, k Branch if Status Flag Cleared if (SREG(s) = 0) then PC←PC+k + 1 None 1/2

BREQ k Branch if Equal if (Z = 1) then PC ← PC + k + 1 None 1/2

BRNE k Branch if Not Equal if (Z = 0) then PC ← PC + k + 1 None 1/2

BRCS k Branch if Carry Set if (C = 1) then PC ← PC + k + 1 None 1/2

BRCC k Branch if Carry Cleared if (C = 0) then PC ← PC + k + 1 None 1/2

BRSH k Branch if Same or Higher if (C = 0) then PC ← PC + k + 1 None 1/2

BRLO k Branch if Lower if (C = 1) then PC ← PC + k + 1 None 1/2

BRMI k Branch if Minus if (N = 1) then PC ← PC + k + 1 None 1/2

BRPL k Branch if Plus if (N = 0) then PC ← PC + k + 1 None 1/2

BRGE k Branch if Greater or Equal, Signed if (N ⊕ V= 0) then PC ← PC + k + 1 None 1/2

BRLT k Branch if Less Than Zero, Signed if (N ⊕ V= 1) then PC ← PC + k + 1 None 1/2

BRHS k Branch if Half Carry Flag Set if (H = 1) then PC ← PC + k + 1 None 1/2

BRHC k Branch if Half Carry Flag Cleared if (H = 0) then PC ← PC + k + 1 None 1/2

BRTS k Branch if T Flag Set if (T = 1) then PC ← PC + k + 1 None 1/2

BRTC k Branch if T Flag Cleared if (T = 0) then PC ← PC + k + 1 None 1/2

BRVS k Branch if Overflow Flag is Set if (V = 1) then PC ← PC + k + 1 None 1/2

BRVC k Branch if Overflow Flag is Cleared if (V = 0) then PC ← PC + k + 1 None 1/2

8025MS–AVR–6/11

ATmega48P/88P/168P

BRIE k Branch if Interrupt Enabled if ( I = 1) then PC ← PC + k + 1 None 1/2

BRID k Branch if Interrupt Disabled if ( I = 0) then PC ← PC + k + 1 None 1/2

BIT AND BIT-TEST INSTRUCTIONS

SBI P,b Set Bit in I/O Register I/O(P,b) ← 1None2

CBI P,b Clear Bit in I/O Register I/O(P,b) ← 0None2

LSL Rd Logical Shift Left Rd(n+1) ← Rd(n), Rd(0) ← 0 Z,C,N,V 1

LSR Rd Logical Shift Right Rd(n) ← Rd(n+1), Rd(7) ← 0 Z,C,N,V 1

ROL Rd Rotate Left Through Carry Rd(0)←C,Rd(n+1)← Rd(n),C←Rd(7) Z,C,N,V 1

ROR Rd Rotate Right Through Carry Rd(7)←C,Rd(n)← Rd(n+1),C←Rd(0) Z,C,N,V 1

ASR Rd Arithmetic Shift Right Rd(n) ← Rd(n+1), n=0..6 Z,C,N,V 1

SWAP Rd Swap Nibbles Rd(3..0)←Rd(7..4),Rd(7..4)←Rd(3..0) None 1

BSET s Flag Set SREG(s) ← 1 SREG(s) 1

BCLR s Flag Clear SREG(s) ← 0 SREG(s) 1

BST Rr, b Bit Store from Register to T T ← Rr(b) T 1

BLD Rd, b Bit load from T to Register Rd(b) ← TNone1

SEC Set Carry C ← 1C1

CLC Clear Carry C ← 0 C 1

SEN Set Negative Flag N ← 1N1

CLN Clear Negative Flag N ← 0 N 1

SEZ Set Zero Flag Z ← 1Z1

CLZ Clear Zero Flag Z ← 0 Z 1

SEI Global Interrupt Enable I ← 1I1

CLI Global Interrupt Disable I ← 0 I 1

SES Set Signed Test Flag S ← 1S1

CLS Clear Signed Test Flag S ← 0 S 1

SEV Set Twos Complement Overflow. V ← 1V1

CLV Clear Twos Complement Overflow V ← 0 V 1

SET Set T in SREG T ← 1T1

CLT Clear T in SREG T ← 0 T 1

SEH Set Half Carry Flag in SREG H ← 1H1

CLH Clear Half Carry Flag in SREG H ← 0 H 1

DATA TRANSFER INSTRUCTIONS

MOV Rd, Rr Move Between Registers Rd ← Rr None 1

MOVW Rd, Rr Copy Register Word Rd+1:Rd ← Rr+1:Rr None 1

LDI Rd, K Load Immediate Rd ← KNone1

LD Rd, X Load Indirect Rd ← (X) None 2

LD Rd, X+ Load Indirect and Post-Inc. Rd ← (X), X ← X + 1 None 2

LD Rd, - X Load Indirect and Pre-Dec. X ← X - 1, Rd ← (X) None 2

LD Rd, Y Load Indirect Rd ← (Y) None 2

LD Rd, Y+ Load Indirect and Post-Inc. Rd ← (Y), Y ← Y + 1 None 2

LD Rd, - Y Load Indirect and Pre-Dec. Y ← Y - 1, Rd ← (Y) None 2

LDD Rd,Y+q Load Indirect with Displacement Rd ← (Y + q) None 2

LD Rd, Z Load Indirect Rd ← (Z) None 2

LD Rd, Z+ Load Indirect and Post-Inc. Rd ← (Z), Z ← Z+1 None 2

LD Rd, -Z Load Indirect and Pre-Dec. Z ← Z - 1, Rd ← (Z) None 2

LDD Rd, Z+q Load Indirect with Displacement Rd ← (Z + q) None 2

LDS Rd, k Load Direct from SRAM Rd ← (k) None 2

ST X, Rr Store Indirect (X) ← Rr None 2

ST X+, Rr Store Indirect and Post-Inc. (X) ← Rr, X ← X + 1 None 2

ST - X, Rr Store Indirect and Pre-Dec. X ← X - 1, (X) ← Rr None 2

ST Y, Rr Store Indirect (Y) ← Rr None 2

ST Y+, Rr Store Indirect and Post-Inc. (Y) ← Rr, Y ← Y + 1 None 2

ST - Y, Rr Store Indirect and Pre-Dec. Y ← Y - 1, (Y) ← Rr None 2

STD Y+q,Rr Store Indirect with Displacement (Y + q) ← Rr None 2

ST Z, Rr Store Indirect (Z) ← Rr None 2

ST Z+, Rr Store Indirect and Post-Inc. (Z) ← Rr, Z ← Z + 1 None 2

ST -Z, Rr Store Indirect and Pre-Dec. Z ← Z - 1, (Z) ← Rr None 2

STD Z+q,Rr Store Indirect with Displacement (Z + q) ← Rr None 2

STS k, Rr Store Direct to SRAM (k) ← Rr None 2

LPM Load Program Memory R0 ← (Z) None 3

LPM Rd, Z Load Program Memory Rd ← (Z) None 3

LPM Rd, Z+ Load Program Memory and Post-Inc Rd ← (Z), Z ← Z+1 None 3

SPM Store Program Memory (Z) ← R1:R0 None -

IN Rd, P In Port Rd ← PNone1

OUT P, Rr Out Port P ← Rr None 1

PUSH Rr Push Register on Stack STACK ← Rr None 2

Mnemonics Operands Description Operation Flags #Clocks

8025MS–AVR–6/11

ATmega48P/88P/168P

Note: 1. These instructions are only available in ATmega168P.

POP Rd Pop Register from Stack Rd ← STACK None 2

MCU CONTROL INSTRUCTIONS

NOP No Operation None 1

SLEEP Sleep (see specific descr. for Sleep function) None 1

WDR Watchdog Reset (see specific descr. for WDR/timer) None 1

BREAK Break For On-chip Debug Only None N/A

Mnemonics Operands Description Operation Flags #Clocks

8025MS–AVR–6/11

ATmega48P/88P/168P

9. Ordering Information

9.1 ATmega48P

Note: 1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information

and minimum quantities.

2. Pb-free packaging complies to the European Directive for Restriction of Hazardous Substances (RoHS directive).Also

Halide free and fully Green.

3. See Figure 29-1 on page 312 and Figure 29-2 on page 312.

4. Tape & Reel

Speed (MHz) Power Supply (V) Ordering Code(2) Package(1) Operational Range

10(3) 1.8 - 5.5

ATmega48PV-10AU

ATmega48PV-10AUR(4)

ATmega48PV-10MMU

ATmega48PV-10MMUR(4)

ATmega48PV-10MU

ATmega48PV-10MUR(4)

ATmega48PV-10PU

32A

28M1

32M1-A

28P3 Industrial

(-40°C to 85°C)

20(3) 2.7 - 5.5

ATmega48P-20AU

ATmega48P-20AUR(4)

ATmega48P-20MMU

ATmega48P-20MMUR(4)

ATmega48P-20MU

ATmega48P-20MUR(4)

ATmega48P-20PU

32A

28M1

32M1-A

28P3

Package Type

32A 32-lead, Thin (1.0mm) Plastic Quad Flat Package (TQFP)

28M1 28-pad, 4 x 4 x 1.0 body, Lead Pitch 0.45mm Quad Flat No-Lead/Micro Lead Frame Package (QFN/MLF)

32M1-A 32-pad, 5 x 5 x 1.0 body, Lead Pitch 0.50mm Quad Flat No-Lead/Micro Lead Frame Package (QFN/MLF)

28P3 28-lead, 0.300” Wide, Plastic Dual Inline Package (PDIP)

8025MS–AVR–6/11

ATmega48P/88P/168P

9.2 ATmega88P

Note: 1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information

and minimum quantities.

2. Pb-free packaging complies to the European Directive for Restriction of Hazardous Substances (RoHS directive).Also

Halide free and fully Green.

3. See Figure 29-1 on page 312 and Figure 29-2 on page 312.

4. Taper & Reel.

Speed (MHz) Power Supply (V) Ordering Code(2) Package(1) Operational Range

10(3) 1.8 - 5.5

ATmega88PV-10AU

ATmega88PV-10AUR(4)

ATmega88PV-10MU

ATmega88PV-10MUR(4)

ATmega88PV-10PU

32A

32M1-A

28P3 Industrial

(-40°C to 85°C)

20(3) 2.7 - 5.5

ATmega88P-20AU

ATmega88P-20AUR(4)

ATmega88P-20MU

ATmega88P-20MUR(4)

ATmega88P-20PU

32A

32M1-A

28P3

Package Type

32A 32-lead, Thin (1.0mm) Plastic Quad Flat Package (TQFP)

28P3 28-lead, 0.300” Wide, Plastic Dual Inline Package (PDIP)

32M1-A 32-pad, 5 x 5 x 1.0 body, Lead Pitch 0.50mm Quad Flat No-Lead/Micro Lead Frame Package (QFN/MLF)

8025MS–AVR–6/11

ATmega48P/88P/168P

9.3 ATmega168P

Note: 1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information

and minimum quantities.

2. Pb-free packaging complies to the European Directive for Restriction of Hazardous Substances (RoHS directive).Also

Halide free and fully Green.

3. See Figure 29-1 on page 312 and Figure 29-2 on page 312.

4. Taper & Reel.

Speed (MHz)(3) Power Supply (V) Ordering Code(2) Package(1) Operational Range

10 1.8 - 5.5

ATmega168PV-10AU

ATmega168PV-10AUR(4)

ATmega168PV-10MU

ATmega168PV-10MUR(4)

ATmega168PV-10PU

32A

32M1-A

28P3 Industrial

(-40°C to 85°C)

20 2.7 - 5.5

ATmega168P-20AU

ATmega168P-20AUR(4)

ATmega168P-20MU

ATmega168P-20MUR(4)

ATmega168P-20PU

32A

32M1-A

28P3

Package Type

32A 32-lead, Thin (1.0mm) Plastic Quad Flat Package (TQFP)

28P3 28-lead, 0.300” Wide, Plastic Dual Inline Package (PDIP)

32M1-A 32-pad, 5 x 5 x 1.0 body, Lead Pitch 0.50mm Quad Flat No-Lead/Micro Lead Frame Package (QFN/MLF)

8025MS–AVR–6/11

ATmega48P/88P/168P

10. Packaging Information

10.1 32A

2325 Orchard Parkway

San Jose, CA 95131

TITLE DRAWING NO.

REV.

32A, 32-lead, 7 x 7 mm Body Size, 1.0 mm Body Thickness,

0.8 mm Lead Pitch, Thin Profile Plastic Quad Flat Package (TQFP) C

32A

2010-10-20

PIN 1 IDENTIFIER

0°~7°

PIN 1

A1 A2 A

eE1 E

Notes:

1. This package conforms to JEDEC reference MS-026, Variation ABA.

2. Dimensions D1 and E1 do not include mold protrusion. Allowable

protrusion is 0.25 mm per side. Dimensions D1 and E1 are maximum

plastic body size dimensions including mold mismatch.

3. Lead coplanarity is 0.10 mm maximum.

A – – 1.20

A1 0.05 – 0.15

A2 0.95 1.00 1.05

D 8.75 9.00 9.25

D1 6.90 7.00 7.10 Note 2

E 8.75 9.00 9.25

E1 6.90 7.00 7.10 Note 2

B 0.30 – 0.45

C 0.09 – 0.20

L 0.45 – 0.75

e 0.80 TYP

COMMON DIMENSIONS

(Unit of Measure = mm)

SYMBOL MIN NOM MAX NOTE

8025MS–AVR–6/11

ATmega48P/88P/168P

10.2 28M1

TITLE DRAWING NO. GPC REV.

Package Drawing Contact:

packagedrawings@atmel.com 28M1ZBVB

28M1, 28-pad, 4 x 4 x 1.0 mm Body, Lead Pitch 0.45 mm,

2.4 x 2.4 mm Exposed Pad, Thermally Enhanced

Plastic Very Thin Quad Flat No Lead Package (VQFN)

10/24/08

SIDE VIEW

Pin 1 ID

BOTTOM VIEW

TOP VIEW

Note: The terminal #1 ID is a Laser-marked Feature.

0.45 COMMON DIMENSIONS

(Unit of Measure = mm)

SYMBOL MIN NOM MAX NOTE

A 0.80 0.90 1.00

A1 0.00 0.02 0.05

b 0.17 0.22 0.27

C 0.20 REF

D 3.95 4.00 4.05

D2 2.35 2.40 2.45

E 3.95 4.00 4.05

E2 2.35 2.40 2.45

e 0.45

L 0.35 0.40 0.45

y 0.00 – 0.08

K 0.20 – –

R 0.20

0.4 Ref

(4x)

8025MS–AVR–6/11

ATmega48P/88P/168P

10.3 32M1-A

2325 Orchard Parkway

San Jose, CA 95131

TITLE DRAWING NO.

REV.

32M1-A, 32-pad, 5 x 5 x 1.0 mm Body, Lead Pitch 0.50 mm, E

32M1-A

5/25/06

3.10 mm Exposed Pad, Micro Lead Frame Package (MLF)

COMMON DIMENSIONS

(Unit of Measure = mm)

SYMBOL MIN NOM MAX NOTE

E1 E

0.08 C

A 0.80 0.90 1.00

A1 – 0.02 0.05

A2 – 0.65 1.00

A3 0.20 REF

b 0.18 0.23 0.30

D2 2.95 3.10 3.25

4.90 5.00 5.10

4.70 4.75 4.80

4.90 5.00 5.10

E2 2.95 3.10 3.25

e 0.50 BSC

L 0.30 0.40 0.50

P – – 0.60

– – 12o

Note: JEDEC Standard MO-220, Fig. 2 (Anvil Singulation), VHHD-2.

TOP VIEW

SIDE VIEW

BOTTOM VIEW

Pin 1 ID

Pin #1 Notch

(0.20 R)

K 0.20 – –

8025MS–AVR–6/11

ATmega48P/88P/168P

10.4 28P3

2325 Orchard Parkway

San Jose, CA 95131

TITLE DRAWING NO.

REV.

28P3, 28-lead (0.300"/7.62 mm Wide) Plastic Dual

Inline Package (PDIP) B

28P3

09/28/01

REF

SEATING PLANE

0º ~ 15º

(4 PLACES)

COMMON DIMENSIONS

(Unit of Measure = mm)

SYMBOL MIN NOM MAX NOTE

A – – 4.5724

A1 0.508 – –

D 34.544 – 34.798 Note 1

E 7.620 – 8.255

E1 7.112 – 7.493 Note 1

B 0.381 – 0.533

B1 1.143 – 1.397

B2 0.762 – 1.143

L 3.175 – 3.429

C 0.203 – 0.356

eB – – 10.160

e 2.540 TYP

Note: 1. Dimensions D and E1 do not include mold Flash or Protrusion.

Mold Flash or Protrusion shall not exceed 0.25 mm (0.010").

8025MS–AVR–6/11

ATmega48P/88P/168P

11. Errata

11.1 Errata ATmega48P

The revision letter in this section refers to the revision of the ATmega48P device.

11.1.1 Rev. C

No known errata.

11.1.2 Rev. B

No known errata.

11.1.3 Rev. A

Not Sampled.

11.2 Errata ATmega88P

The revision letter in this section refers to the revision of the ATmega88P device.

11.2.1 Rev. C

Not sampled.

11.2.2 Rev. B

No known errata.

11.2.3 Rev. A

No known errata.

11.3 Errata ATmega168P

The revision letter in this section refers to the revision of the ATmega168P device.

11.3.1 Rev B

No known errata.

11.3.2 Rev A

No known errata.

8025MS–AVR–6/11

ATmega48P/88P/168P

12. Datasheet Revision History

Please note that the referring page numbers in this section are referred to this document. The

referring revision in this section are referring to the document revision.

12.1 Rev. 8025M-06/11

12.2 Rev. 8025L-07/10

12.3 Rev. 8025K-10/09

12.4 Rev. 8025J-05/09

12.5 Rev. 8025I-02/09

12.6 Rev. 8025H-02/09

1. Added Atmel QTouch Library Support and QTouch Sensing Capability Features.

2. Updated “Ordering Information” to include Tape and Reel devices.

3. Updated the datasheet with Atmel new style guide.

1. Removed from the front page, the note “Not recommended for new design”.

2. Editorial updates.

1. Updated “Low Frequency Crystal Oscillator” with the Table 9-8 on page 33.

2. Editorial updates.

1. Removed the “About” section.

2. Removed ATmega328P device and its reference from the data sheet.

3. Editorial updates.

1. Removed “preliminary” from ATmega48P/88P/168P.

1. Added Power-save Maximum values and footnote to ”ATmega48P DC Characteris-

tics” on page 310.

2. Added Power-save Maximum values and footnote to ”ATmega88P DC Characteris-

tics” on page 311.

3. Added Power-save Maximum values and footnote to ”ATmega168P DC Characteris-

tics” on page 311.

4. Added Power-save Maximum values and footnote to ”” on page 312.

5. Added errata for revision A, ”” on page 23.

8025MS–AVR–6/11

ATmega48P/88P/168P

12.7 Rev. 8025G-01/09

12.8 Rev. 8025F-08/08

12.9 Rev. 8025E-08/08

1 ATmega48P/88P not recommended for new designs.

2. Updated the footnote Note1 of the Table 9-3 on page 30.

3. Updated the Table 9-5 on page 31 by removing a footnote Note1.

4. Updated the Table 9-11 on page 34 by removing a footnote Note1.

5. Updated the footnote Note1 of the Table 9-13 on page 35.

6. Updated the footnote Note2 of the ”ATmega48P DC Characteristics” on page 310

and removed TBD from the table.

7. Updated the footnote Note2 of the ”ATmega88P DC Characteristics” on page 311

and removed TBD from the table.

8. Updated the footnote Note2 of the ”ATmega168P DC Characteristics” on page 311

and removed TBD from the table.

9. Updated the footnote Note2 of the ”” on page 312 and removed TBD from the table.

10. Updated the footnote Note1 of the Table 29-4 on page 314.

11. Replaced the Figure 30-69 on page 358 by a correct one.

12. Replaced the Figure 29-173 on page 419 by a correct one.

13. Updated ”Errata” on page 23.

14. Updated ”MCUCR – MCU Control Register” on page 44.

15. Updated ”TCCR2B – Timer/Counter Control Register B” on page 159.

1. Updated ”Register Summary” on page 9 with Power-save numbers.

2. Added ATmega328P ”Standby Supply Current” on page 408.

1. Updated description of ”Stack Pointer” on page 13.

2. Updated description of use of external capacitors in ”Low Frequency Crystal Oscilla-

tor” on page 33.

3. Updated Table 9-10 in ”Low Frequency Crystal Oscillator” on page 33.

4. Added note to ”Address Match Unit” on page 220.

5. Added section ”Reading the Signature Row from Software” on page 283.

6. Updated ”Program And Data Memory Lock Bits” on page 291 to include

ATmega328P in the description.

7. Added ”” on page 312.

8. Updated ”Speed Grades” on page 312 for ATmega328P.

9. Removed note 6 and 7 from the table ”2-wire Serial Interface Characteristics” on

page 317.

10. Added figure ”Minimum Reset Pulse width vs. VCC.” on page 346 for ATmega48P.

11. Added figure ”Minimum Reset Pulse width vs. VCC.” on page 370 for ATmega88P.

12. Added figure ”Minimum Reset Pulse width vs. VCC.” on page 394 for ATmega168P.

13. Added ”Register Summary” on page 9.

14. Updated Ordering Information for ”Packaging Information” on page 19.

8025MS–AVR–6/11

ATmega48P/88P/168P

12.10 Rev. 8025D-03/08

12.11 Rev. 8025C-01/08

12.12 Rev. 8025B-01/08

12.13 Rev. 8025A-07/07

1. Updated figures in ”Speed Grades” on page 312.

2. Updated note in Table 29-4 in ”System and Reset Characteristics” on page 314.

3. Ordering codes for ”Packaging Information” on page 19 updated.

- ATmega328P is offered in 20 MHz option only.

4. Added Errata for ATmega328P rev. B, ”” on page 23.

1. Power-save Maximum values removed form ”ATmega48P DC Characteristics” on

page 310, ”ATmega88P DC Characteristics” on page 311, and ”ATmega168P DC

Characteristics” on page 311.

1. Updated ”Features” on page 1.

2. Added ”Data Retention” on page 8.

3. Updated Table 9-2 on page 29.

4. Removed “Low-frequency Crystal Oscillator Internal Load Capacitance“ table

from”Low Frequency Crystal Oscillator” on page 33.

5. Removed JTD bit from ”MCUCR – MCU Control Register” on page 45.

Updated typical and general program setup for Reset and Interrupt Vector Addresses

in ”Interrupt Vectors in ATmega168P” on page 63 and ”Interrupt Vectors in

ATmega328P” on page 65.

7. Updated Interrupt Vectors Start Address in Table 12-5 on page 64 and Table 11-7 on

page 66.

8. Updated ”Temperature Measurement” on page 259.

9. Updated ATmega328P ”Fuse Bits” on page 292.

10. Removed VOL3/VOH3 rows from ”DC Characteristics” on page 309.

11. Updated condition for VOL in ”DC Characteristics” on page 309.

Updated max value for VIL2 in ”DC Characteristics” on page 309.

12. Added ”ATmega48P DC Characteristics” on page 310, ”ATmega88P DC Characteris-

tics” on page 311, and ”ATmega168P DC Characteristics” on page 311.

13. Updated ”System and Reset Characteristics” on page 314.

14.

Added ”ATmega48P Typical Characteristics” on page 322, ”ATmega88P Typical

Characteristics” on page 346, and ”ATmega168P Typical Characteristics” on page

370.

15. Updated note in ”Instruction Set Summary” on page 13.

1. Initial revision.

8025MS–AVR–6/11

Atmel Corporation

2325 Orchard Parkway

San Jose, CA 95131

USA

Tel: (+1)(408) 441-0311

Fax: (+1)(408) 487-2600

www.atmel.com

Atmel Asia Limited

Unit 1-5 & 16, 19/F

BEA Tower, Millennium City 5

418 Kwun Tong Road

Kwun Tong, Kowloon

HONG KONG

Tel: (+852) 2245-6100

Fax: (+852) 2722-1369

Atmel Munich GmbH

Business Campus

Parkring 4

D-85748 Garching b. Munich

GERMANY

Tel: (+49) 89-31970-0

Fax: (+49) 89-3194621

Atmel Japan

9F, Tonetsu Shinkawa Bldg.

1-24-8 Shinkawa

Chuo-ku, Tokyo 104-0033

JAPAN

Tel: (+81)(3) 3523-3551

Fax: (+81)(3) 3523-7581

Atmel®, Atmel logo and combinations thereof, AVR®, QTouch®, QMatrix®, AVR Studio® and others are registered trademarks or trade-

marks of Atmel Corporation or its subsidiaries. Windows® and others are registered trademarks of Microsoft Corporation in U.S. and

other countries. Other terms and product names may be trademarks of others.

Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to

any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL

TERMS AND CONDITIONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY

EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF

MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT,

INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS AND PROF-

ITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL

HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or com-

pleteness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice.

Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suit-

able for, and shall not be used in, automotive applications. Atmel products are not intended, authorized, or warranted for use as components in applica-

tions intended to support or sustain life.