LMC6442 www.ti.com SNOS013E - SEPTEMBER 1997 - REVISED MARCH 2013 LMC6442 Dual Micropower Rail-to-Rail Output Single Supply Operational Amplifier Check for Samples: LMC6442 FEATURES DESCRIPTION * * * * * * * * * The LMC6442 is ideal for battery powered systems, where very low supply current (less than one microamp per amplifier) and Rail-to-Rail output swing is required. It is characterized for 2.2V to 10V operation, and at 2.2V supply, the LMC6442 is ideal for single (Li-Ion) or two cell (NiCad or alkaline) battery systems. 1 2 (Typical, VS = 2.2V) Output Swing to Within 30 mV of Supply Rail High Voltage Gain 103 dB Gain Bandwidth Product 9.5 KHz Ensured for: 2.2V, 5V, 10V Low Supply Current 0.95 A/Amplifier Input Voltage Range -0.3V to V+ -0.9V 2.1 W/Amplifier Power Consumption Stable for AV +2 or AV -1 Operation from single supply is enhanced by the wide common mode input voltage range which includes the ground (or negative supply) for ground sensing applications. Very low (5 fA, typical) input bias current and near constant supply current over supply voltage enhance the LMC6442's performance near the endof-life battery voltage. APPLICATIONS * * * * * * * * The LMC6442 is designed for battery powered systems that require long service life through low supply current, such as smoke and gas detectors, and pager or personal communications systems. Portable Instruments Smoke/Gas/CO/Fire Detectors Pagers/Cell Phones Instrumentation Thermostats Occupancy Sensors Cameras Active Badges Designed for closed loop gains of greater than plus two (or minus one), the amplifier has typically 9.5 KHz GBWP (Gain Bandwidth Product). Unity gain can be used with a simple compensation circuit, which also allows capacitive loads of up to 300 pF to be driven, as described in the Application Information section. Connection Diagram Top View Figure 1. 8-Pin SOIC / PDIP Package See Package Numbers D0008A, P0008E These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 1997-2013, Texas Instruments Incorporated LMC6442 SNOS013E - SEPTEMBER 1997 - REVISED MARCH 2013 (1) (2) Absolute Maximum Ratings ESD Tolerance www.ti.com (3) 2 kV Differential Input Voltage Supply Voltages (V+) + 0.3V, (V-) - 0.3V Voltage at Input/Output Pin Supply Voltage (V+ - V-): Current at Input Pin 16V (4) Current at Output Pin (5) 5 mA (6) 30 mA Lead Temp. (soldering 10 sec) 260C -65C to +150C Storage Temp. Range: Junction Temp. (1) (2) (3) (4) (5) (6) (7) (7) 150C Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but specific performance is not ensured. For ensured specifications and the test conditions, see the Electrical Characteristics. If Military/Aerospace specified devices are required, please contact the TI Sales Office/ Distributors for availability and specifications. Human body model, 1.5 k in series with 100 pF. Limiting input pin current is only necessary for input voltages that exceed absolute maximum input voltage ratings. Applies to both single-supply and split-supply operation. Continuous short circuit operation at elevated ambient temperature can result in exceeding the maximum allowed junction temperature of 150C. Output currents in excess of 30 mA over long term may adversely affect reliability. Do not short circuit output to V+, when V+ is greater than 13V or reliability will be adversely affected. The maximum power dissipation is a function of TJ(MAX), JA, and TA. The maximum allowable power dissipation at any ambient temperature is PD= (TJ(MAX) - TA)/ JA. All numbers apply for packages soldered directly into a PC board. Operating Ratings (1) 1.8V VS 11V Supply Voltage -40C < TJ < +85C Junction Temperature Range: LMC6442AI, LMC6442I Thermal Resistance (JA) (1) D0008A Package, 8-pin Surface Mount 193C/W P0008E Package, 8-pin Molded DIP 115C/W Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but specific performance is not ensured. For ensured specifications and the test conditions, see the Electrical Characteristics. 2.2V Electrical Characteristics Unless otherwise specified, all limits ensured for TJ = 25C, V+ = 2.2V, V- = 0V, VCM = VO = V +/2, and RL = 1 M to V+/2. Boldface limits apply at the temperature extremes. Parameter Test Conditions Typ (1) LMC6442AI Limit (2) LMC6442I Limit (2) Units 3 4 7 8 mV max DC Electrical Characteristics VOS Input Offset Voltage TCVOS Temp. coefficient of input offset voltage IB Input Bias Current See (3) Input Offset Current See (3) CMRR Common Mode Rejection Ratio -0.1V VCM 0.5V CIN Common Mode Input Capacitance PSRR Power Supply Rejection Ratio IOS (1) (2) (3) 2 -0.75 0.4 V/C 0.005 4 4 pA max 0.0025 2 2 pA max 92 67 67 67 67 4.7 VS = 2.5 V to 10V 95 dB min pF 75 75 75 75 dB min Typical Values represent the most likely parametric norm. All limits are specified by testing or statistical analysis unless otherwise specified. Limits specified by design. Submit Documentation Feedback Copyright (c) 1997-2013, Texas Instruments Incorporated Product Folder Links: LMC6442 LMC6442 www.ti.com SNOS013E - SEPTEMBER 1997 - REVISED MARCH 2013 2.2V Electrical Characteristics (continued) Unless otherwise specified, all limits ensured for TJ = 25C, V+ = 2.2V, V- = 0V, VCM = VO = V +/2, and RL = 1 M to V+/2. Boldface limits apply at the temperature extremes. Parameter VCM Input Common-Mode Voltage Range AV Large Signal Voltage Gain Test Conditions 1.3 CMRR 50 dB Sourcing Sinking -0.3 (4) Output Swing Output Short Circuit Current IS Supply Current (2 amplifiers) LMC6442I Limit (2) Units 1.05 0.95 1.05 0.95 V min -0.2 0 -0.2 0 V max dB min 94 VID = 100 mV 103 80 80 2.18 2.15 2.15 2.15 2.15 V min 22 60 60 60 60 mV max (5) VID = -100 mV ISC LMC6442AI Limit (2) 100 (4) VO = 0.22V to 2V VO (1) Typ (5) Sourcing, VID = 100 mV (6) (5) 50 18 17 18 17 Sinking, VID = -100 mV (6) (5) 50 20 19 20 19 1.90 2.4 3.0 2.6 3.2 RL = open + V = 1.8V, RL = open A min A max 2.10 AC Electrical Characteristics SR Slew Rate (7) 2.2 V/ms GBWP Gain-Bandwidth Product 9.5 KHz m Phase Margin 63 deg (4) (5) (6) (7) (8) See (8) RL connected to V+/2. For Sourcing Test, VO > V+/2. For Sinking tests, VO < V+/2. VID is differential input voltage referenced to inverting input. Output shorted to ground for sourcing, and shorted to V+ for sinking short circuit current test. Slew rate is the slower of the rising and falling slew rates. See the Typical Performance Characteristics and Applications Information sections for more details. 5V Electrical Characteristics Unless otherwise specified, all limits ensured for TJ = 25C, V+ = 5V, V- = 0V, VCM = VO = V +/2, and RL = 1 M to V+/2. Boldface limits apply at the temperature extremes. Parameter Test Conditions Typ (1) LMC6442AI Limit (2) LMC6442I Limit (2) Units 3 4 7 8 mV max DC Electrical Characteristics VOS Input Offset Voltage TCVOS Temp. coefficient of input offset voltage IB Input Bias Current See (3) Input Offset Current See (3) CMRR Common Mode Rejection Ratio -0.1V VCM 3.5V CIN Common Mode Input Capacitance PSRR Power Supply Rejection Ratio IOS (1) (2) (3) -0.75 0.4 V/C 0.005 4 4 pA max 0.0025 2 2 pA max 102 70 70 70 70 dB min 4.1 VS = 2.5 V to 10V 95 pF 75 75 75 75 dB min Typical Values represent the most likely parametric norm. All limits are specified by testing or statistical analysis unless otherwise specified. Limits specified by design. Submit Documentation Feedback Copyright (c) 1997-2013, Texas Instruments Incorporated Product Folder Links: LMC6442 3 LMC6442 SNOS013E - SEPTEMBER 1997 - REVISED MARCH 2013 www.ti.com 5V Electrical Characteristics (continued) Unless otherwise specified, all limits ensured for TJ = 25C, V+ = 5V, V- = 0V, VCM = VO = V +/2, and RL = 1 M to V+/2. Boldface limits apply at the temperature extremes. Parameter VCM Test Conditions Input Common-Mode Voltage Range AV 4.1 CMRR 50 dB Large Signal Voltage Gain Sourcing Sinking -0.4 (4) Output Swing IS LMC6442I Limit (2) Units 3.85 3.75 3.85 3.75 V min -0.2 0 -0.2 0 V max dB min 94 VID = 100 mV (5) VID = -100 mV ISC LMC6442AI Limit (2) 100 (4) VO = 0.5V to 4.5V VO (1) Typ (5) 103 80 80 4.99 4.95 4.95 4.95 4.95 V min 20 50 50 50 50 mV max Output Short Circuit Current Sourcing, VID = 100 mV (6) (5) 500 300 200 300 200 Sinking, VID = -100 mV (6) (5) 350 200 150 200 150 1.90 2.4 3.0 2.6 3.2 A max 2.5 2.5 V/ms Supply Current (2 amplifiers) RL = open A min AC Electrical Characteristics SR Slew Rate (7) 4.1 GBWP Gain-Bandwidth Product 10 KHz m Phase Margin See 64 deg THD Total Harmonic Distortion AV = +2, f = 100 Hz, RL = 10 M, VOUT = 1 VPP 0.08 % (4) (5) (6) (7) (8) (8) RL connected to V+/2. For Sourcing Test, VO > V+/2. For Sinking tests, VO < V+/2. VID is differential input voltage referenced to inverting input. Output shorted to ground for sourcing, and shorted to V+ for sinking short circuit current test. Slew rate is the slower of the rising and falling slew rates. See the Typical Performance Characteristics and Applications Information sections for more details. 10V Electrical Characteristics Unless otherwise specified, all limits ensured for TJ = 25C, V+ = 10V, V- = 0V, VCM = VO = V +/2, and RL = 1 M to V+/2. Boldface limits apply at the temperature extremes. Parameter Test Conditions Typ (1) LMC6442AI Limit (2) LMC6442I Limit (2) Units 3 4 7 8 mV max DC Electrical Characteristics VOS Input Offset Voltage TCVOS Temp. coefficient of input offset voltage IB Input Bias Current See (3) Input Offset Current See CMRR Common Mode Rejection Ratio -0.1V VCM 8.5V CIN Common Mode Input Capacitance PSRR Power Supply Rejection Ratio IOS (1) (2) (3) 4 -1.5 0.4 V/C 0.005 4 4 pA max 0.0025 2 2 pA max 105 70 70 70 70 (3) 3.5 VS= 2.5 V to 10V 95 dB min pF 75 75 75 75 dB min Typical Values represent the most likely parametric norm. All limits are specified by testing or statistical analysis unless otherwise specified. Limits specified by design. Submit Documentation Feedback Copyright (c) 1997-2013, Texas Instruments Incorporated Product Folder Links: LMC6442 LMC6442 www.ti.com SNOS013E - SEPTEMBER 1997 - REVISED MARCH 2013 10V Electrical Characteristics (continued) Unless otherwise specified, all limits ensured for TJ = 25C, V+ = 10V, V- = 0V, VCM = VO = V +/2, and RL = 1 M to V+/2. Boldface limits apply at the temperature extremes. Parameter VCM Input Common-Mode Voltage Range AV Large Signal Voltage Gain Test Conditions Typ 9.1 CMRR 50 dB Sourcing Sinking -0.4 (4) Output Swing Output Short Circuit Current IS Supply Current (2 amplifiers) LMC6442I Limit (2) Units 8.85 8.75 8.85 8.75 V min -0.2 0 -0.2 0 V max dB min 100 VID = 100 mV (5) VID = -100 mV ISC LMC6442AI Limit (2) 120 (4) VO = 0.5V to 9.5V VO (1) (5) 104 80 80 9.99 9.97 9.97 9.97 9.97 V min 22 50 50 50 50 mV max Sourcing, VID = 100 mV (6) (5) 2100 1200 1000 1200 1000 Sinking, VID = -100 mV (6) (5) 900 600 500 600 500 1.90 2.4 3.0 2.6 3.2 A max 2.5 2.5 V/ms RL = open A min AC Electrical Characteristics SR Slew Rate (7) 4.1 GBWP Gain-Bandwidth Product 10.5 m Phase Margin See en Input-Referred Voltage Noise in (4) (5) (6) (7) (8) (9) (8) KHz 68 deg RL = open f = 10 Hz 170 nV/Hz Input-Referred Current Noise RL = open f = 10 Hz 0.0002 pA/Hz Crosstalk Rejection See 85 dB (9) RL connected to V+/2. For Sourcing Test, VO > V+/2. For Sinking tests, VO < V+/2. VID is differential input voltage referenced to inverting input. Output shorted to ground for sourcing, and shorted to V+ for sinking short circuit current test. Slew rate is the slower of the rising and falling slew rates. See the Typical Performance Characteristics and Applications Information sections for more details. Input referred, V+ = 10V and RL = 10 M connected to 5V. Each amp excited in turn with 1 KHz to produce about 10 VPP output. Submit Documentation Feedback Copyright (c) 1997-2013, Texas Instruments Incorporated Product Folder Links: LMC6442 5 LMC6442 SNOS013E - SEPTEMBER 1997 - REVISED MARCH 2013 www.ti.com Typical Performance Characteristics VS = 5V, Single Supply, TA = 25C unless otherwise specified 6 Total Supply Current vs. Supply Voltage Total Supply Current vs. Supply Voltage (Negative Input Overdrive) Figure 2. Figure 3. Total Supply Current vs. Supply Voltage (Positive Input Overdrive) Input Bias Current vs. Temperature Figure 4. Figure . Offset Voltage vs. Common Mode Voltage (VS = 2.2V) Offset Voltage vs. Common Mode Voltage (VS = 5V) Figure 5. Figure 6. Submit Documentation Feedback Copyright (c) 1997-2013, Texas Instruments Incorporated Product Folder Links: LMC6442 LMC6442 www.ti.com SNOS013E - SEPTEMBER 1997 - REVISED MARCH 2013 Typical Performance Characteristics (continued) VS = 5V, Single Supply, TA = 25C unless otherwise specified Offset Voltage vs. Common Mode Voltage (VS = 10V) Swing Towards V- vs. Supply Voltage Figure 7. Figure 8. Swing Towards V+ vs. Supply Voltage Swing From Rail(s) vs. Temperature Figure 9. Figure 10. Output Source Current vs. Output Voltage Output Sink Current vs. Output Voltage Figure 11. Figure 12. Submit Documentation Feedback Copyright (c) 1997-2013, Texas Instruments Incorporated Product Folder Links: LMC6442 7 LMC6442 SNOS013E - SEPTEMBER 1997 - REVISED MARCH 2013 www.ti.com Typical Performance Characteristics (continued) VS = 5V, Single Supply, TA = 25C unless otherwise specified 8 Maximum Output Voltage vs. Load Resistance Large Signal Voltage Gain vs. Supply Voltage Figure 13. Figure 14. Open Loop Gain/Phase vs. Frequency Open Loop Gain/Phase vs. Frequency For Various CL (ZL = 1 M II CL) Figure 15. Figure 16. Open Loop Gain/Phase vs. Frequency For Various CL (ZL = 100 K II CL) Gain Bandwidth Product vs. Supply Voltage Figure 17. Figure 18. Submit Documentation Feedback Copyright (c) 1997-2013, Texas Instruments Incorporated Product Folder Links: LMC6442 LMC6442 www.ti.com SNOS013E - SEPTEMBER 1997 - REVISED MARCH 2013 Typical Performance Characteristics (continued) VS = 5V, Single Supply, TA = 25C unless otherwise specified Phase Margin (Worst Case) vs. Supply Voltage CMRR vs. Frequency Figure 19. Figure 20. PSRR vs. Frequency Positive Slew Rate vs. Supply Voltage Figure 21. Figure 22. Negative Slew Rate vs. Supply Voltage Cross-Talk Rejection vs. Frequency Figure 23. Figure 24. Submit Documentation Feedback Copyright (c) 1997-2013, Texas Instruments Incorporated Product Folder Links: LMC6442 9 LMC6442 SNOS013E - SEPTEMBER 1997 - REVISED MARCH 2013 www.ti.com Typical Performance Characteristics (continued) VS = 5V, Single Supply, TA = 25C unless otherwise specified 10 Input Voltage Noise vs. Frequency Output Impedance vs. Frequency Figure 25. Figure 26. THD+N vs. Frequency THD+N vs. Amplitude Figure 27. Figure 28. Maximum Output Swing vs. Frequency Small Signal Step Response (AV = +2) (CL = 12 pF, 100 pF) Figure 29. Figure 30. Submit Documentation Feedback Copyright (c) 1997-2013, Texas Instruments Incorporated Product Folder Links: LMC6442 LMC6442 www.ti.com SNOS013E - SEPTEMBER 1997 - REVISED MARCH 2013 Typical Performance Characteristics (continued) VS = 5V, Single Supply, TA = 25C unless otherwise specified Large Signal Step Response (AV = +2) (CL = 100 pF) Small Signal Step Response (AV = -1) (CL= 1M II 100 pF, 200 pF) Figure 31. Figure 32. Small Signal Step Response (AV = +1) For Various CL Large Signal Step Response (AV = +1) (CL = 200 pF) Figure 33. Figure 34. Submit Documentation Feedback Copyright (c) 1997-2013, Texas Instruments Incorporated Product Folder Links: LMC6442 11 LMC6442 SNOS013E - SEPTEMBER 1997 - REVISED MARCH 2013 www.ti.com APPLICATIONS INFORMATION USING LMC6442 IN UNITY GAIN APPLICATIONS LMC6442 is optimized for maximum bandwidth and minimal external components when operating at a minimum closed loop gain of +2 (or -1). However, it is also possible to operate the device in a unity gain configuration by adding external compensation as shown in Figure 35: Figure 35. AV = +1 Operation by adding CC and RC Using this compensation technique it is possible to drive capacitive loads of up to 300 pF without causing oscillations (see the Typical Performance Characteristics for step response plots). This compensation can also be used with other gain settings in order to improve stability, especially when driving capacitive loads (for optimum performance, RC and CC may need to be adjusted). USING "T" NETWORK Compromises need to be made whenever high gain inverting stages need to achieve a high input impedance as well. This is especially important in low current applications which tend to deal with high resistance values. Using a traditional inverting amplifier, gain is inversely proportional to the resistor value tied between the inverting terminal and input while the input impedance is equal to this value. For example, in order to build an inverting amplifier with an input impedance of 10M and a gain of 100, one needs to come up with a feedback resistor of 1000 M -an expensive task. An alternate solution is to use a "T" Network in the feedback path, as shown in Figure 36. Closed loop gain, AV is given by: (1) Figure 36. "T" Network Used to Replace High Value Resistor It must be noted, however, that using this scheme, the realizable bandwidth would be less than the theoretical maximum. With feedback factor, , defined as: (2) (3) BW(-3 dB) GBWP * In this case, assuming a GBWP of about 10 KHz, the expected BW would be around 50 Hz (vs. 100 Hz with the conventional inverting amplifier). 12 Submit Documentation Feedback Copyright (c) 1997-2013, Texas Instruments Incorporated Product Folder Links: LMC6442 LMC6442 www.ti.com SNOS013E - SEPTEMBER 1997 - REVISED MARCH 2013 Looking at the problem from a different view, with RF defined by AV*Rin, one could select a value for R in the "T" Network and then determine R1 based on this selection: (4) Figure 37. "T" Network Values for Various Values of R For convenience, Figure 37 shows R1 vs. RF for different values of R. DESIGN CONSIDERATIONS FOR CAPACITIVE LOADS As with many other opamps, the LMC6442 is more stable at higher closed loop gains when driving a capacitive load. Figure 38 shows minimum closed loop gain versus load capacitance, to achieve less than 10% overshoot in the output small signal response. In addition, the LMC6442 is more stable when it provides more output current to the load and when its output voltage does not swing close to V-. The LMC6442 is more tolerant to capacitive loads when the equivalent output load resistance is lowered or when output voltage is 1V or greater from the V- supply. The capacitive load drive capability is also improved by adding an isolating resistor in series with the load and the output of the device. Figure 39 shows the value of this resistor for various capacitive loads (AV = -1), while limiting the output to less than 10 % overshoot. Referring to the Typical Performance Characteristics plot of Phase Margin (Worst Case) vs. Supply Voltage, note that Phase Margin increases as the equivalent output load resistance is lowered. This plot shows the expected Phase Margin when the device output is very close to V-, which is the least stable condition of operation. Comparing this Phase Margin value to the one read off the Open Loop Gain/Phase vs. Frequency plot, one can predict the improvement in Phase Margin if the output does not swing close to V-. This dependence of Phase Margin on output voltage is minimized as long as the output load, RL, is about 1M or less. Output Phase Reversal: The LMC6442 is immune against this behavior even when the input voltages exceed the common mode voltage range. Output Time Delay: Due to the ultra low power consumption of the device, there could be as long as 2.5 ms of time delay from when power is applied to when the device output reaches its final value. Submit Documentation Feedback Copyright (c) 1997-2013, Texas Instruments Incorporated Product Folder Links: LMC6442 13 LMC6442 SNOS013E - SEPTEMBER 1997 - REVISED MARCH 2013 www.ti.com Figure 38. Minimum Operating Gain vs. Capacitive Load Figure 39. Isolating Resistor Value vs Capacitive Load 14 Submit Documentation Feedback Copyright (c) 1997-2013, Texas Instruments Incorporated Product Folder Links: LMC6442 LMC6442 www.ti.com SNOS013E - SEPTEMBER 1997 - REVISED MARCH 2013 Application Circuits V + = 5V: IS < 10 A, f/VC = 4.3 (Hz/V) Figure 40. Micropower Single Supply Voltage to Frequency Converter Figure 41. Gain Stage with Current Boosting Submit Documentation Feedback Copyright (c) 1997-2013, Texas Instruments Incorporated Product Folder Links: LMC6442 15 LMC6442 SNOS013E - SEPTEMBER 1997 - REVISED MARCH 2013 www.ti.com Figure 42. Offset Nulling Schemes 16 Submit Documentation Feedback Copyright (c) 1997-2013, Texas Instruments Incorporated Product Folder Links: LMC6442 LMC6442 www.ti.com SNOS013E - SEPTEMBER 1997 - REVISED MARCH 2013 REVISION HISTORY Changes from Revision D (March 2013) to Revision E * Page Changed layout of National Data Sheet to TI format .......................................................................................................... 16 Submit Documentation Feedback Copyright (c) 1997-2013, Texas Instruments Incorporated Product Folder Links: LMC6442 17 PACKAGE OPTION ADDENDUM www.ti.com 1-Nov-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) LMC6442AIM/NOPB ACTIVE SOIC D 8 95 Green (RoHS & no Sb/Br) SN | CU SN Level-1-260C-UNLIM -40 to 85 LMC64 42AIM LMC6442AIMX NRND SOIC D 8 2500 TBD Call TI Call TI -40 to 85 LMC64 42AIM LMC6442AIMX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) SN | CU SN Level-1-260C-UNLIM -40 to 85 LMC64 42AIM LMC6442IM/NOPB ACTIVE SOIC D 8 95 Green (RoHS & no Sb/Br) SN | CU SN Level-1-260C-UNLIM -40 to 85 LMC64 42IM LMC6442IMX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 LMC64 42IM LMC6442IN/NOPB ACTIVE PDIP P 8 40 Green (RoHS & no Sb/Br) CU SN Level-1-NA-UNLIM -40 to 85 LMC6442 IN (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 1-Nov-2013 (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 23-Sep-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant LMC6442AIMX SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1 LMC6442AIMX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1 LMC6442IMX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 23-Sep-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LMC6442AIMX SOIC D 8 2500 367.0 367.0 35.0 LMC6442AIMX/NOPB SOIC D 8 2500 367.0 367.0 35.0 LMC6442IMX/NOPB SOIC D 8 2500 367.0 367.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2013, Texas Instruments Incorporated