HIGH-SPEED 2.5V 256/128/64K x 36 IDT70T3519/99/89S SYNCHRONOUS DUAL-PORT STATIC RAM WITH 3.3V OR 2.5V INTERFACE Features: True Dual-Port memory cells which allow simultaneous access of the same memory location High-speed data access - Commercial: 3.4 (200MHz)/3.6ns (166MHz)/ 4.2ns (133MHz)(max.) - Industrial: 3.6ns (166MHz)/4.2ns (133MHz) (max.) Selectable Pipelined or Flow-Through output mode Counter enable and repeat features Dual chip enables allow for depth expansion without additional logic Full synchronous operation on both ports - 5ns cycle time, 200MHz operation (14Gbps bandwidth) - Fast 3.4ns clock to data out - 1.5ns setup to clock and 0.5ns hold on all control, data, and address inputs @ 200MHz - Data input, address, byte enable and control registers - Self-timed write allows fast cycle time Interrupt and Collision Detection Flags Separate byte controls for multiplexed bus and bus matching compatibility Dual Cycle Deselect (DCD) for Pipelined Output Mode 2.5V (100mV) power supply for core LVTTL compatible, selectable 3.3V (150mV) or 2.5V (100mV) power supply for I/Os and control signals on each port Industrial temperature range (-40C to +85C) is available at 166MHz and 133MHz Available in a 256-pin Ball Grid Array (BGA), a 208-pin Plastic Quad Flatpack (PQFP) and 208-pin fine pitch Ball Grid Array (fpBGA) Supports JTAG features compliant with IEEE 1149.1 Due to limited pin count JTAG is not supported on the 208pin PQFP package Green parts available, see ordering information Functional Block Diagram FT/PIPEL BE3L BE3R BE2L BE2R BE1L BE1R BE0L BE0R 1/0 0a 1a 0b 1b 0c 1c 0d 1d 1d 0d 1c 0c 1b 0b 1a 0a a b c d d c b a FT/PIPER 1/0 R/WL R/WR CE0L CE1L 1 1 0 0 B B B B B B B B W W W W W W WW 0 1 2 3 3 2 1 0 L L L L R R RR 1/0 OEL Dout0-8_L Dout9-17_L Dout18-26_L Dout27-35_L 1/0 OER Dout0-8_R Dout9-17_R Dout18-26_R Dout27-35_R 1d 0d 1c 0c 1b 0b 1a 0a FT/PIPEL CE0 R CE1 R , 0a 1a 0b 1b 0c 1c 0d 1d FT/PIPE R 0/1 0/1 a bc d d cba 256/128/64K x 36 MEMORY ARRAY I/O0L - I/O35L Din_L I/O0R - I/O35R Din_R CLKR CLKL A0L REPEATL ADSL CNTEN L , A17R ( 1) A17L (1) Counter/ Address Reg. ADDR_L Counter/ Address Reg. ADDR_R TDI INTE RRUPT COLLISION DETECTION LOGIC CE 0 L CE1L R /W L A 0R REPEATR ADSR CNTENR CE0 R CE1 R JTAG TD O TCK TMS TRST R/W R COL L INTL COLR INTR ZZL (2) ZZ CONTROL LOGIC ZZR (2) NOTES: 1. Address A17 is a NC for the IDT70T3599. Also, Addresses A17 and A16 are NC's for the IDT70T3589. 2. The sleep mode pin shuts off all dynamic inputs, except JTAG inputs, when asserted. All static inputs, i.e., PL/FTx and OPTx and the sleep mode pins themselves (ZZx) are not affected during sleep mode. 5666 drw 01 JANUARY 2009 1 (c)2009 Integrated Device Technology, Inc. DSC 5666/10 IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges Description: The IDT70T3519/99/89 is a high-speed 256/128/64K x 36 bit synchronous Dual-Port RAM. The memory array utilizes Dual-Port memory cells to allow simultaneous access of any address from both ports. Registers on control, data, and address inputs provide minimal setup and hold times. The timing latitude provided by this approach allows systems to be designed with very short cycle times. With an input data register, the IDT70T3519/99/89 has been optimized for applications having unidirec- 6.42 2 tional or bidirectional data flow in bursts. An automatic power down feature, controlled by CE0 and CE1, permits the on-chip circuitry of each port to enter a very low standby power mode. The 70T3519/99/89 can support an operating voltage of either 3.3V or 2.5V on one or both ports, controllable by the OPT pins. The power supply for the core of the device (VDD) is at 2.5V. IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges Pin Configuration (3,4,5,6,9) 70T3519/99/89BC BC-256(7) 256-Pin BGA Top View(8) 06/19/02 A1 NC B1 I/O18L C1 A2 TDI B2 NC C2 I/O18R I/O19L D1 D2 A3 NC B3 TDO C3 A4 B4 NC C4 VSS A16L(2) D3 A5 A17L(1) A14L D4 B5 A15L C5 A13L D5 A6 A11L B6 A12L C6 A10L D6 A7 A8L B7 A9L C7 A7L D7 A8 A9 BE2L CE1L B9 B8 BE3L BE1L B10 B11 C10 C11 BE0L CLKL ADSL D9 D8 A11 OEL CNTENL CE0L R/WL REPEATL C9 C8 A10 D10 D11 A12 A5L B12 A4L C12 A6L D12 A13 A2L B13 A1L C13 A3L D13 A14 A0L B14 VDD C14 A15 A16 NC NC B16 B15 I/O17L NC C16 C15 OPTL I/O17R I/O16L D14 D15 D16 I/O20R I/O19R I/O20L PIPE/FTL VDDQL VDDQL VDDQR VDDQR VDDQL VDDQL VDDQR VDDQR VDD I/O15R I/O15L I/O16R E1 E2 E3 E4 I/O21R I/O21L I/O22L VDDQL F1 F2 F3 F4 I/O23L I/O22R I/O23R VDDQL G1 G2 G3 G4 I/O24R I/O24L I/O25L VDDQR H1 H2 H3 H4 E5 VDD F5 VDD G5 VSS H5 I/O26L I/O25R I/O26R VDDQR VSS J1 J2 J3 J4 I/O27L I/O28R I/O27R VDDQL K1 K2 K3 K4 I/O29R I/O29L I/O28L VDDQL L1 L2 L3 L4 J5 ZZR K5 VSS L5 I/O30L I/O31R I/O30R VDDQR VDD M1 M2 M3 M4 I/O32R I/O32L I/O31L VDDQR N1 N2 N3 N4 M5 VDD N5 E6 VDD E7 INTL F7 F6 NC G6 VSS H6 VSS COLL G7 VSS H7 VSS J7 J6 VSS K6 VSS L6 NC M6 VDD N6 VSS K7 VSS L7 COLR M7 INTR N7 E8 E9 VSS VSS F9 F8 VSS VSS G9 G8 VSS H8 VSS H9 VSS J8 VSS J9 VSS K8 VSS K9 VSS L8 VSS L9 VSS VSS M9 M8 VSS N8 VSS N9 E10 VSS F10 VSS G10 VSS H10 VSS J10 VSS K10 VSS L10 VSS M10 VSS N10 E11 VDD F11 VSS G11 VSS H11 VSS J11 VSS K11 VSS L11 VSS M11 VDD N11 E12 F12 P2 P3 P4 P5 I/O35R I/O34L TMS A16R(2) A13R R1 I/O35L T1 NC R2 NC T2 TCK R3 TRST T3 NC R4 NC T4 R5 A15R T5 A17R(1) A14R P6 A10R R6 A12R T6 A11R P7 A7R R7 A9R T7 A8R P8 P9 P10 P11 BE1R BE0R CLKR ADSR R9 R8 R10 R11 BE3R CE0R R/WR REPEATR T8 T9 BE2R CE1R T10 T11 OER CNTENR E14 E16 E15 F13 F14 F15 F16 VDD VDDQR I/O12R I/O13R I/O12L G12 VSS H12 VSS J12 ZZL K12 VSS L12 VDD M12 VDD N12 I/O33L I/O34R I/O33R PIPE/FTR VDDQR VDDQR VDDQL VDDQL VDDQR VDDQR VDDQL VDDQL P1 E13 VDD VDDQR I/O13L I/O14L I/O14R P12 A6R R12 A4R T12 A5R G13 G14 G15 G16 VDDQL I/O10L I/O11L I/O11R H13 H14 VDDQL I/O9R J13 J14 H16 H15 IO9L I/O10R J15 J16 VDDQR I/O8R I/O7R K13 K14 VDDQR I/O6R L13 L14 VDDQL I/O5L M13 M14 VDDQL I/O3R N13 VDD P13 A3R R13 A1R T13 A2R N14 I/O2L P14 K15 K16 I/O6L L15 OPTR T14 A0R I/O7L L16 I/O4R I/O5R M16 M15 I/O3L I/O4L N16 N15 I/O1R I/O2R P15 P16 I/O0L I/O0R R14 I/O8L I/O1L R16 R15 NC T15 NC , T16 NC NC 5666 drw 02d NOTES: 1. Pin is a NC for IDT70T3599 and IDT70T3589. 2. Pin is a NC for IDT70T3589. 3. All VDD pins must be connected to 2.5V power supply. 4. All VDDQ pins must be connected to appropriate power supply: 3.3V if OPT pin for that port is set to VDD (2.5V), and 2.5V if OPT pin for that port is set to VSS (0V). 5. All VSS pins must be connected to ground supply. 6. Package body is approximately 17mm x 17mm x 1.4mm, with 1.0mm ball-pitch. 7. This package code is used to reference the package diagram. 8. This text does not indicate orientation of the actual part-marking. 9. Pins A15 and T15 will be VREFL and VREFR respectively for future HSTL device. 6.42 3 , IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges Pin Configuration (3,4,5,6,9,10) (con't.) 208 207 206 205 204 203 202 201 200 199 198 197 196 195 194 193 192 191 190 189 188 187 186 185 184 183 182 181 180 179 178 177 176 175 174 173 172 171 170 169 168 167 166 165 164 163 162 161 160 159 158 157 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 70T3519/99/89DR DR-208(7) 208-Pin PQFP Top View(8) 156 155 154 153 152 151 150 149 148 147 146 145 144 143 142 141 140 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 108 107 106 105 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 I/O19L I/O19R I/O20L I/O20R VDDQL VSS I/O21L I/O21R I/O22L I/O22R VDDQR VSS I/O23L I/O23R I/O24L I/O24R VDDQL VSS I/O25L I/O25R I/O26L I/O26R VDDQR ZZR VDD VDD VSS VSS VDDQL VSS I/O27R I/O27L I/O28R I/O28L VDDQR VSS I/O29R I/O29L I/O30R I/O30L VDDQL VSS I/O31R I/O31L I/O32R I/O32L VDDQR VSS I/O33R I/O33L I/O34R I/O34L VSS VDDQR I/O18R I/O18L VSS PL/FTL COLL INTL NC NC A17L(1) A16L(2) A15L A14L A13L A12L A11L A10L A9L A8L A7L BE3L BE2L BE1L BE0L CE1L CE0L VDD VDD VSS VSS CLKL OEL R/WL ADSL CNTENL REPEATL A6L A5L A4L A3L A2L A1L A0L VDD VDD NC OPTL I/O17L I/O17R VDDQR VSS 06/19/02 I/O16L I/O16R I/O15L I/O15R VSS VDDQL I/O14L I/O14R I/O13L I/O13R VSS VDDQR I/O12L I/O12R I/O11L I/O11R VSS VDDQL I/O10L I/O10R I/O9L I/O9R VSS VDDQR VDD VDD VSS VSS ZZL VDDQL I/O8R I/O8L I/O7R I/O7L VSS VDDQR I/O6R I/O6L I/O5R I/O5L VSS VDDQL I/O4R I/O4L I/O3R I/O3L VSS VDDQR I/O2R I/O2L I/O1R I/O1L VSS VDDQL I/O35R I/O35L PL/FTR NC COLR INTR NC NC A17R(1) A16R(2) A15R A14R A13R A12R A11R A10R A9R A8R A7R BE3R BE2R BE1R BE0R CE1R CE0R VDD VDD VSS VSS CLKR OER R/WR ADSR CNTENR REPEATR A6R A5R A4R A3R A2R A1R A0R VDD VSS NC OPTR I/O0L I/O0R VDDQL VSS , 5666 drw 02a NOTES: 1. Pin is a NC for IDT70T3599 and IDT70T3589. 2. Pin is a NC for IDT70T3589. 3. All VDD pins must be connected to 2.5V power supply. 4. All VDDQ pins must be connected to appropriate power supply: 3.3V if OPT pin for that port is set to VDD (2.5V), and 2.5V if OPT pin for that port is set to Vss (0V). 5. All VSS pins must be connected to ground supply. 6. Package body is approximately 28mm x 28mm x 3.5mm. 7. This package code is used to reference the package diagram. 8. This text does not indicate orientation of the actual part-marking. 9. Due to limited pin count, JTAG is not supported in the DR-208 package. 10. Pins 162 and 99 will be VREFL and VREFR respectively for future HSTL device. 6.42 4 IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges Pin Configuration (3,4,5,6,9) (con't.) 01/23/03 A1 A2 I/O19L I/O18L B1 I/O20R C1 B2 A3 V SS B3 V SS I/O18R C2 C3 I/O22L E1 D2 V SS E2 D3 COLL A16L(2) A12L B4 TDI C4 B5 D4 B6 A17L(1) A 13L C5 D5 I/O21L I/O20L A15L E3 A8 A7 A5 TDO VDDQL I/O19R VDDQR PL/FTL INT L D1 A6 A4 C6 A 14L D6 A 11L B7 A8L B8 A9L C7 BE2L C8 A10L A7L BE1L B9 CE0L C9 BE 3L CE1L D8 D7 A9 BE0L D9 VDD A10 VDD B10 VSS C10 V SS D10 A11 A12 A13 CLKL CNTENL A4L B11 ADSL C11 R/WL D11 OEL REPEATL B12 A5L C12 A6L D12 A3L B13 A1L C13 A2L D13 A14 A 0L B14 NC C14 A15 B15 C15 D15 E4 E14 E15 F1 F14 VDDQL I/O23R I/O24L G1 G2 I/O26L V SS H1 H2 G3 F4 VSS VSS G14 G4 I/O25L I/O24R H3 J2 VDDQL VDD K1 I/O28R L1 K2 VSS L2 J3 VSS K3 I/O27R L3 H4 70T3519/99/89BF BF-208(7) H14 VDD J4 J14 ZZR ZZL 208-Pin fpBGA Top View(8) K4 VSS K14 L4 L14 I/O6R M1 M14 M3 M4 VDDQL I/O29L I/O30R VSS N1 N2 N3 VSS N4 N14 P2 P3 P4 P5 P6 P7 I/O32R I/O32L VDDQR I/O35R TRST A16R(2) A12R R1 VSS T1 R2 R3 R4 U1 VSS R5 R6 I/O33L I/O34R TCK A17R(1) A13R T2 T3 T4 I/O33R I/O34L VDDQL TMS U2 U3 U4 I/O35L PL/FTR COLR F15 E17 E16 VSS F16 I/O13L F17 I/O12R I/O11L VDDQR G15 G16 G17 H15 I/O9R J15 VDD K15 H16 H17 V SS J16 L15 I/O7L M15 T5 INTR U5 A15R T6 A14R U6 A11R R7 A9R T7 A10R U7 A7R P8 A8R R8 P9 BE1R R9 BE 2R CE0R T8 T9 BE3R CE1R U8 BE0R U9 VDD P10 VDD R10 VSS T10 V SS U10 OER P11 P12 P13 CLKR C NTEN R A 4R R11 ADS R T11 R/W R R12 A5R T12 A6R U12 A3R R13 A1R T13 A2R U13 A 0R P14 J17 K16 K17 L16 NC T14 VSS U14 VDD V SS L17 V SS M16 I/O8L M17 I/O6L I/O5R VDDQR N15 P15 I/O2L I/O3L R14 I/O10R VSS VDDQR N16 N17 I/O3R VDDQL I/O4R I/O31L V SS I/O31R I/O30L P1 VSS D17 D16 I/O7R VDDQL I/O8R I/O29R I/O28L VDDQR I/O27L M2 C17 I/O9L VDDQL I/O10L I/O11R VDD I/O26R VDDQR I/O25R J1 C16 VDD I/O17R VDDQL I/O14L I/O14R I/O12L I/O13R F3 B17 B16 VDD I/O16R I/O15L D14 V SS VDDQR I/O16L I/O15R I/O23L I/O22R VDDQR I/O21R F2 A17 A16 OPTL I/O17L R15 P16 I/O5L P17 VSS R16 I/O4L R17 V DDQL I/O1R VDDQR T15 I/O0R U15 T17 T16 VSS I/O2R U17 U16 OPTR I/O0L I/O1L 5666 drw 02c NOTES: 1. Pin is a NC for IDT70T3599 and IDT70T3589. 2. Pin is a NC for IDT70T3589. 3. All VDD pins must be connected to 2.5V power supply. 4. All VDDQ pins must be connected to appropriate power supply: 3.3V if OPT pin for that port is set to VDD (2.5V), and 2.5V if OPT pin for that port is set to V SS (0V). 5. All VSS pins must be connected to ground supply. 6. Package body is approximately 15mm x 15mm x 1.4mm with 0.8mm ball pitch. 7. This package code is used to reference the package diagram. 8. This text does not indicate orientation of the actual part-marking. 9. Pins B14 and R14 will be V REFL and VREFR respectively for future HSTL device. 6.42 5 IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges Pin Names Left Port Right Port Names CE0L, CE1L CE0R, CE1R Chip Enables (Input)(7) R/WL R/WR Read/Write Enable (Input) OEL OER Output Enable (Input) A0L - A17L(6) A0R - A17R(6) Address (Input) I/O0L - I/O35L I/O0R - I/O35R Data Input/Output CLKL CLKR Clock (Input) PL/FTL PL/FTR Pipeline/Flow-Through (Input) ADSL ADSR Address Strobe Enable (Input) CNTENL CNTENR Counter Enable (Input) REPEATL REPEATR Counter Repeat(3) BE0L - BE3L BE0R - BE3R Byte Enables (9-bit bytes) (Input)(7) VDDQL VDDQR Power (I/O Bus) (3.3V or 2.5V)(1) (Input) OPTL OPTR Option for selecting V DDQX(1,2) (Input) ZZL ZZR Sleep Mode pin(4) (Input) VDD Power (2.5V)(1) (Input) VSS Ground (0V) (Input) TDI(5) Test Data Input TDO(5) Test Data Output TCK (5) Test Logic Clock (10MHz) (Input) (5) Test Mode Select (Input) TMS TRST Reset (Initialize TAP Controller) (Input) (5) INTL INTR Interrupt Flag (Output) COLL COLR Collision Alert (Output) 5666 tbl 01 NOTES: 1. VDD, OPTX, and VDDQX must be set to appropriate operating levels prior to applying inputs on the I/Os and controls for that port. 2. OPTX selects the operating voltage levels for the I/Os and controls on that port. If OPTX is set to VDD (2.5V), then that port's I/Os and controls will operate at 3.3V levels and VDDQX must be supplied at 3.3V. If OPT X is set to VSS (0V), then that port's I/Os and address controls will operate at 2.5V levels and VDDQX must be supplied at 2.5V. The OPT pins are independent of one another--both ports can operate at 3.3V levels, both can operate at 2.5V levels, or either can operate at 3.3V with the other at 2.5V. 3. When REPEATX is asserted, the counter will reset to the last valid address loaded via ADS X. 4. The sleep mode pin shuts off all dynamic inputs, except JTAG inputs, when asserted. All static inputs, i.e., PL/FTx and OPTx and the sleep mode pins themselves (ZZx) are not affected during sleep mode. It is recommended that boundry scan not be operated during sleep mode. 5. Due to limited pin count, JTAG is not supported in the DR-208 package. 6. Address A17x is a NC for the IDT70T3599. Also, Addresses A17x and A16x are NC's for the IDT 70T3589. 7. Chip Enables and Byte Enables are double buffered when PL/FT = VIH, i.e., the signals take two cycles to deselect. 6.42 6 IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges Truth Table I--Read/Write and Enable Control (1,2,3,4) OE CLK CE0 CE1 BE3 BE2 BE1 BE0 R/W ZZ Byte 3 I/O27-35 Byte 2 I/O18-26 Byte 1 I/O9-17 Byte 0 I/O0-8 X H X X X X X X L High-Z High-Z High-Z High-Z Deselected-Power Down X X L X X X X X L High-Z High-Z High-Z High-Z Deselected-Power Down X L H H H H H X L High-Z High-Z High-Z High-Z All Bytes Deselected X L H H H H L L L High-Z High-Z High-Z DIN Write to Byte 0 Only X L H H H L H L L High-Z High-Z DIN High-Z Write to Byte 1 Only X L H H L H H L L High-Z DIN High-Z High-Z Write to Byte 2 Only X L H L H H H L L DIN High-Z High-Z High-Z Write to Byte 3 Only X L H H H L L L L High-Z High-Z DIN DIN Write to Lower 2 Bytes Only X L H L L H H L L DIN DIN High-Z High-Z Write to Upper 2 bytes Only X L H L L L L L L DIN DIN DIN DIN L L H H H H L H L High-Z High-Z High-Z DOUT Read Byte 0 Only L L H H H L H H L High-Z High-Z DOUT High-Z Read Byte 1 Only L L H H L H H H L High-Z DOUT High-Z High-Z Read Byte 2 Only L L H L H H H H L DOUT High-Z High-Z High-Z Read Byte 3 Only MODE Write to All Bytes L L H H H L L H L High-Z High-Z DOUT DOUT Read Lower 2 Bytes Only L L H L L H H H L DOUT DOUT High-Z High-Z Read Upper 2 Bytes Only L L H L L L L H L DOUT DOUT DOUT DOUT Read All Bytes H X X X X X X X L High-Z High-Z High-Z High-Z Outputs Disabled X X X X X X X X X H High-Z High-Z High-Z High-Z Sleep Mode NOTES: 1. "H" = V IH, "L" = VIL, "X" = Don't Care. 2. ADS, CNTEN, REPEAT = X. 3. OE and ZZ are asynchronous input signals. 4. It is possible to read or write any combination of bytes during a given access. A few representative samples have been illustrated here. Truth Table II--Address Counter Control Address Previous Internal Address Internal Address Used CLK An X An ADS L(4) (1,2) MODE CNTEN REPEAT(6) I/O(3) X H DI/O (n) H DI/O(n+1) Counter Enabled--Internal Address generation External Address Blocked--Counter disab led (An + 1 reused) X An An + 1 X An + 1 An + 1 H H H DI/O(n+1) X X An X X L(4) DI/O(n) H 5666 tbl 02 (5) L External Address Used Counter Set to last valid ADS load 5666 tbl 03 NOTES: 1. "H" = V IH, "L" = VIL, "X" = Don't Care. 2. Read and write operations are controlled by the appropriate setting of R/W, CE 0, CE1, BEn and OE. 3. Outputs configured in flow-through output mode: if outputs are in pipelined mode the data out will be delayed by one cycle. 4. ADS and REPEAT are independent of all other memory control signals including CE0, CE1 and BEn 5. The address counter advances if CNTEN = VIL on the rising edge of CLK, regardless of all other memory control signals including CE0, CE1, BEn. 6. When REPEAT is asserted, the counter will reset to the last valid address loaded via ADS. This value is not set at power-up: a known location should be loaded via ADS during initialization if desired. Any subsequent ADS access during operations will update the REPEAT address location. 6.42 7 IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges Recommended Operating Temperature and Supply Voltage Ambient Temperature Grade GND VDD 0 C to +70 C 0V 2.5V + 100mV -40OC to +85OC 0V 2.5V + 100mV O Commercial Industrial (1) O NOTES: 1. This is the parameter TA. This is the "instant on" case temperature. 5666 tbl 04 Recommended DC Operating Conditions with VDDQ at 2.5V Symbol Parameter Min. Typ. Max. Unit V DD Core Supply Voltage 2.4 2.5 2.6 V V DDQ I/O Supply Voltage (3) 2.4 2.5 2.6 V V SS Ground 0 0 0 V V IH Input High Volltage (Address, Control & Data I/O Inputs)(3) 1.7 ____ VDDQ + 100mV (2) V V IH Input High Voltage JTAG 1.7 ____ VDD + 100mV (2) V V IH Input High Voltage ZZ, OPT, PIPE/FT V DD - 0.2V ____ VDD + 100mV (2) V VIL Input Low Voltage -0.3(1) ____ 0.7 V VIL Input Low Voltage ZZ, OPT, PIPE/FT -0.3(1) ____ 0.2 V _ 5666 tbl 05a NOTES: 1. VIL (min.) = -1.0V for pulse width less than tCYC /2 or 5ns, whichever is less. 2. VIH (max.) = VDDQ + 1.0V for pulse width less than tCYC /2 or 5ns, whichever is less. 3. To select operation at 2.5V levels on the I/Os and controls of a given port, the OPT pin for that port must be set to Vss(0V), and V DDQX for that port must be supplied as indicated above. Recommended DC Operating Conditions with VDDQ at 3.3V Symbol VDD Parameter Core Supply Voltage (3) VDDQ I/O Supply Voltage VSS Ground VIH Input High Voltage (Address, Control &Data I/O Inputs)(3) VIH Input High Voltage JTAG VIH Input High Voltage ZZ, OPT, PIPE/FT Min. Typ. Max. Unit 2.4 2.5 2.6 V 3.15 3.3 3.45 V 0 0 0 V 2.0 ____ VDDQ + 150mV(2) V 1.7 ____ VDD + 100mV(2) V VDD - 0.2V ____ VDD + 100mV(2) V (1) 0.8 V 0.2 V _ VIL Input Low Voltage -0.3 ____ VIL Input Low Voltage ZZ, OPT, PIPE/FT -0.3(1) ____ 5666 tbl 05b NOTES: 1. VIL (min.) = -1.0V for pulse width less than tCYC/2, or 5ns, whichever is less. 2. VIH (max.) = V DDQ + 1.0V for pulse width less than tCYC /2 or 5ns, whichever is less. 3. To select operation at 3.3V levels on the I/Os and controls of a given port, the OPT pin for that port must be set to VDD (2.5V), and VDDQX for that port must be supplied as indicated above. 6.42 8 IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges Absolute Maximum Ratings (1) Symbol Rating Commercial & Industrial Unit VTERM (VDD) VDD Terminal Voltage with Respect to GND -0.5 to 3.6 VTERM(2) (VDDQ ) VDDQ Terminal Voltage with Respect to GND -0.3 to VDDQ + 0.3 V VTERM(2) (INPUTS and I/O's) Input and I/O Terminal Voltage with Respect to GND -0.3 to VDDQ + 0.3 V TBIAS(3) Temperature Under Bias -55 to +125 o C TSTG Storage Temperature -65 to +150 o C TJN Junction Temperature +150 o C IOUT(For VDDQ = 3.3V) DC Output Current 50 IOUT(For VDDQ = 2.5V) DC Output Current 40 V mA mA 5666 tbl 06 NOTES: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. This is a steady-state DC parameter that applies after the power supply has reached its nominal operating value. Power sequencing is not necessary; however, the voltage on any Input or I/O pin cannot exceed VDDQ during power supply ramp up. 3. Ambient Temperature under DC Bias. No AC Conditions. Chip Deselected. Capacitance (1) (TA = +25C, F = 1.0MHZ) PQFP ONLY Symbol CIN COUT(3) Parameter Input Capacitance Output Capacitance Conditions(2) Max. Unit VIN = 3dV 8 pF VOUT = 3dV 10.5 pF 5666 tbl 07 NOTES: 1. These parameters are determined by device characterization, but are not production tested. 2. 3dV references the interpolated capacitance when the input and output switch from 0V to 3V or from 3V to 0V. 3. COUT also references CI/O. DC Electrical Characteristics Over the Operating Temperature and Supply Voltage Range (VDD = 2.5V 100mV) 70T3519/99/89S Symbol |ILI| |ILI| |ILO| VOL (3.3V) Parameter Test Conditions Input Leakage Current(1) (1,2) JTAG & ZZ Input Leakage Current (1,3) Output Leakage Current Output Low Voltage (1) (1) Min. Max. Unit VDDQ = Max., VIN = 0V to VDDQ ___ 10 A VDD = Max., V IN = 0V to VDD ___ 30 A CE0 = VIH or CE1 = VIL, VOUT = 0V to VDDQ ___ 10 A IOL = +4mA, VDDQ = Min. ___ 0.4 V V V VOH (3.3V) Output High Voltage IOH = -4mA, V DDQ = Min. 2.4 ___ VOL (2.5V) Output Low Voltage (1) IOL = +2mA, VDDQ = Min. ___ 0.4 VOH (2.5V) Output High Voltage (1) IOH = -2mA, V DDQ = Min. 2.0 ___ V 5666 tbl 08 NOTES: 1. VDDQ is selectable (3.3V/2.5V) via OPT pins. Refer to p.5 for details. 2. Applicable only for TMS, TDI and TRST inputs. 3. Outputs tested in tri-state mode. 6.42 9 IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges DC Electrical Characteristics Over the Operating Temperature and Supply Voltage Range (3) (VDD = 2.5V 100mV) 70T3519/99/89 S200 Com'l Only(8) Symbol IDD ISB1(6) ISB2(6) ISB3 ISB4(6) Izz Parameter Test Condition Version 70T3519/99/89 S166 Com'l & Ind(7) 70T3519/99/89 S133 Com'l & Ind Typ.(4) Max. Typ.(4) Max. Typ.(4) Max. Dynamic Operating Current (Both Ports Active) CEL and CER= VIL, Outputs Disabled, f = fMAX(1) COM'L S 375 525 320 450 260 370 IND S ___ ___ 320 510 260 450 Standby Current (Both Ports - TTL Level Inputs) CEL = CER = VIH f = fMAX(1) COM'L S 205 270 175 230 140 190 IND S ___ ___ 175 275 140 235 Standby Current (One Port - TTL Level Inputs) CE"A" = VIL and CE"B" = VIH(5) Active Port Outputs Disabled, f=fMAX(1) COM'L S 300 375 250 325 200 250 IND S ___ ___ 250 365 200 310 Full Standby Current (Both Ports - CMOS Level Inputs) Both Ports CEL and CER > VDDQ - 0.2V, VIN > VDDQ - 0.2V or VIN < 0.2V, f = 0(2) COM'L S 5 15 5 15 5 15 IND S ___ ___ 5 20 5 20 Full Standby Current (One Port - CMOS Level Inputs) CE"A" < 0.2V and CE"B" > VDDQ - 0.2V(5) VIN > VDDQ - 0.2V or VIN < 0.2V Active Port, Outputs Disabled, f = fMAX(1) COM'L S 300 375 250 325 200 250 IND S ___ ___ 250 365 200 310 Sleep Mode Current (Both Ports - TTL Level Inputs) ZZL = ZZR = VIH f=fMAX(1) COM'L S 5 15 5 15 5 15 IND S ___ ___ 5 20 5 20 Unit mA mA mA mA mA mA 5666 tbl 09 NOTES: 1. At f = fMAX, address and control lines (except Output Enable) are cycling at the maximum frequency clock cycle of 1/tCYC , using "AC TEST CONDITIONS". 2. f = 0 means no address, clock, or control lines change. Applies only to input at CMOS level standby. 3. Port "A" may be either left or right port. Port "B" is the opposite from port "A". 4. VDD = 2.5V, TA = 25C for Typ, and are not production tested. IDD DC(f=0) = 15mA (Typ). 5. CEX = VIL means CE0X = VIL and CE1X = VIH CEX = VIH means CE0X = VIH or CE1X = V IL CEX < 0.2V means CE0X < 0.2V and CE1X > VDDQ - 0.2V CEX > VDDQ - 0.2V means CE0X > V DDQ - 0.2V or CE1X - 0.2V "X" represents "L" for left port or "R" for right port. 6. ISB1, I SB2 and ISB4 will all reach full standby levels (ISB3) on the appropriate port(s) if ZZL and/or ZZR = VIH. 7. 166MHz I-Temp is not available in the BF-208 package. 8. 200Mhz is not available in the BF-208 and DR-208 packages. 6.42 10 IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges AC Test Conditions (VDDQ - 3.3V/2.5V) Input Pulse Levels (Address & Controls) GND to 3.0V/GND to 2.4V Input Pulse Levels (I/Os) GND to 3.0V/GND to 2.4V Input Rise/Fall Times 2ns Input Timing Reference Levels 1.5V/1.25V Output Reference Levels 1.5V/1.25V Output Load Figure 1 5666 tbl 10 50 50 DATAOUT 1.5V/1.25 10pF (Tester) 5666 drw 03 Figure 1. AC Output Test load. tCD (Typical, ns) Capacitance (pF) from AC Test Load 6.42 11 5666 drw 04 , IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges AC Electrical Characteristics Over the Operating Temperature Range (Read and Write Cycle Timing) (2,3) (VDD = 2.5V 100mV, TA = 0C to +70C) Symbol Parameter 70T3519/99/89 S200 Com'l Only(5) 70T3519/99/89 S166 Com'l & Ind(4) 70T3519/99/89 S133 Com'l & Ind Min. Max. Min. Max. Min. Max. Unit tCYC1 Clock Cycle Time (Flow-Through)(1) 15 ____ 20 ____ 25 ____ ns tCYC2 Clock Cycle Time (Pipelined)(1) 5 ____ 6 ____ 7.5 ____ ns ns (1) tCH1 Clock High Time (Flow-Through) 6 ____ 8 ____ 10 ____ tCL1 Clock Low Time (Flow-Through)(1) 6 ____ 8 ____ 10 ____ ns tCH2 Clock High Time (Pipelined)(2) 2 ____ 2.4 ____ 3 ____ ns tCL2 Clock Low Time (Pipelined)(1) 2 ____ 2.4 ____ 3 ____ ns ns tSA Address Setup Time 1.5 ____ 1.7 ____ 1.8 ____ tHA Address Hold Time 0.5 ____ 0.5 ____ 0.5 ____ ns tSC Chip Enable Setup Time 1.5 ____ 1.7 ____ 1.8 ____ ns ns tHC Chip Enable Hold Time 0.5 ____ 0.5 ____ 0.5 ____ tSB Byte Enable Setup Time 1.5 ____ 1.7 ____ 1.8 ____ ns tHB Byte Enable Hold Time 0.5 ____ 0.5 ____ 0.5 ____ ns tSW R/W Setup Time 1.5 ____ 1.7 ____ 1.8 ____ ns ns tHW R/W Hold Time 0.5 ____ 0.5 ____ 0.5 ____ tSD Input Data Setup Time 1.5 ____ 1.7 ____ 1.8 ____ ns tHD Input Data Hold Time 0.5 ____ 0.5 ____ 0.5 ____ ns tSAD ADS Setup Time 1.5 ____ 1.7 ____ 1.8 ____ ns tHAD ADS Hold Time 0.5 ____ 0.5 ____ 0.5 ____ ns tSCN CNTEN Setup Time 1.5 ____ 1.7 ____ 1.8 ____ ns tHCN CNTEN Hold Time 0.5 ____ 0.5 ____ 0.5 ____ ns tSRPT REPEAT Setup Time 1.5 ____ 1.7 ____ 1.8 ____ ns tHRPT REPEAT Hold Time 0.5 ____ 0.5 ____ 0.5 ____ ns tOE Output Enable to Data Valid ____ 4.4 ____ 4.4 ____ 4.6 ns tOLZ(6) Output Enable to Output Low-Z 1 ____ 1 ____ 1 ____ ns tOHZ(6) Output Enable to Output High-Z 1 3.4 1 3.6 1 4.2 ns tCD1 Clock to Data Valid (Flow-Through)(1) ____ (1) 10 ____ 12 ____ 15 ns ____ tCD2 Clock to Data Valid (Pipelined) 3.4 ____ 3.6 ____ 4.2 ns tDC Data Output Hold After Clock High 1 ____ 1 ____ 1 ____ ns tCKHZ(6) Clock High to Output High-Z 1 3.4 1 3.6 1 4.2 ns ns ns (6) tCKLZ Clock High to Output Low-Z 1 ____ 1 ____ 1 ____ tINS Interrupt Flag Set Time ____ 7 ____ 7 ____ 7 tINR Interrupt Flag Reset Time ____ 7 ____ 7 ____ 7 ns tCOLS Collision Flag Set Time ____ 3.4 ____ 3.6 ____ 4.2 ns tCOLR Collision Flag Reset Time ____ 3.4 ____ 3.6 ____ 4.2 ns 2 ____ 2 ____ cycles tZZSC Sleep Mode Set Cycles 2 ____ tZZRC Sleep Mode Recovery Cycles 3 ____ 3 ____ 3 ____ cycles 4 ____ 5 ____ 6 ____ ns Port-to-Port Delay tCO Clock-to-Clock Offset tOFS Clock-to-Clock Offset for Collision Detection Please refer to Collision Detection Timing Table on Page 21 5666 tbl 11 NOTES: 1. The Pipelined output parameters (tCYC2, tCD2) apply to either or both left and right ports when PL/FTX = VDD (2.5V). Flow-through parameters (tCYC1, tCD1) apply when PL/FT = Vss (0V) for that port. 2. All input signals are synchronous with respect to the clock except for the asynchronous Output Enable (OE), PL/FT and OPT. PL/FT and OPT should be treated as DC signals, i.e. steady state during operation. 3. These values are valid for either level of VDDQ (3.3V/2.5V). See page 6 for details on selecting the desired operating voltage levels for each port. 4. 166MHz I-Temp is not available in the BF-208 package. 5. 200Mhz is not available in the BF-208 and DR-208 packages. 6. Guaranteed by design (not production tested). 6.42 12 IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges Timing Waveform of Read Cycle for Pipelined Operation (FT/PIPE'X' = VIH)(1,2) tCYC2 tCH2 tCL2 CLK CE0 tSC tSC tHC tHC (3) CE1 tSB tSB tHB BEn R/W ADDRESS (4) tSW tHW tSA tHA An An + 1 (1 Latency) An + 2 An + 3 tDC tCD2 DATAOUT Qn tCKLZ OE tHB (5) Qn + 1 Qn + 2 (5) (1) tOHZ tOLZ (1) tOE 5666 drw 05 Timing Waveform of Read Cycle for Flow-through Output (FT/PIPE"X" = VIL)(1,2,6) tCYC1 tCH1 tCL1 CLK CE0 tSC tSC tHC tHC (3) CE1 tSB tHB BEn tSB R/W tHB tSW tHW tSA (4) ADDRESS tHA An An + 1 tCD1 DATAOUT An + 2 tCKHZ Qn Qn + 2 (5) Qn + 1 tCKLZ OE An + 3 tDC tOHZ tOLZ tDC (1) tOE NOTES: 1. OE is asynchronously controlled; all other inputs depicted in the above waveforms are synchronous to the rising clock edge. 2. ADS = VIL, CNTEN and REPEAT = VIH. 3. The output is disabled (High-Impedance state) by CE0 = VIH, CE1 = VIL, BEn = VIH following the next rising edge of the clock. Refer to Truth Table 1. 4. Addresses do not have to be accessed sequentially since ADS = VIL constantly loads the address on the rising edge of the CLK; numbers are for reference use only. 5. If BEn was HIGH, then the appropriate Byte of DATAOUT for Qn + 2 would be disabled (High-Impedance state). 6. "x" denotes Left or Right port. The diagram is with respect to that port. 6.42 13 5666 drw 06 IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges Timing Waveform of a Multi-Device Pipelined Read tCH2 (1,2) tCYC2 tCL2 CLK tSA tHA A0 ADDRESS(B1) tSC tHC CE0(B1) tSC tHC tCD2 tCD2 tCKHZ Q0 DATAOUT(B1) tSC tCKHZ A6 A5 A4 A3 A2 A1 tSC CE0(B2) Q3 tCKLZ tDC tHA A0 ADDRESS(B2) tCD2 Q1 tDC tSA A6 A5 A4 A3 A2 A1 tHC tHC tCD2 DATAOUT(B2) tCKHZ tCD2 Q4 Q2 tCKLZ tCKLZ 5666 drw 07 Timing Waveform of a Multi-Device Flow-Through Read tCH1 (1,2) tCYC1 tCL1 CLK tSA A0 ADDRESS(B1) CE0(B1) tHA tSC tHC tSC tHC tCD1 tCD1 D0 DATAOUT(B1) tCKHZ tSA (1) tCD1 tCD1 D3 D1 tDC ADDRESS(B2) A6 A5 A4 A3 A2 A1 tCKLZ tDC (1) D5 tCKHZ (1) tCKLZ (1) tHA A0 A1 A6 A5 A4 A3 A2 tSC tHC CE0(B2) tSC tHC tCD1 DATAOUT(B2) tCKLZ (1) tCKHZ (1) tCD1 D2 tCKLZ (1) tCKHZ (1) D4 5666 drw 08 NOTES: 1. B1 Represents Device #1; B2 Represents Device #2. Each Device consists of one IDT70T3519/99/89 for this waveform, and are setup for depth expansion in this example. ADDRESS(B1) = ADDRESS(B2) in this situation. 2. BEn, OE, and ADS = VIL; CE1(B1) , CE1(B2) , R/W, CNTEN, and REPEAT = VIH. 6.42 14 IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges Timing Waveform of Left Port Write to Pipelined Right Port Read (1,2,4) CLK"A" tSW tHW tSA tHA R/W"A" ADDRESS"A" tSD DATAIN"A" NO MATCH MATCH tHD VALID tCO(3) CLK"B" tCD2 R/W"B" ADDRESS"B" tSW tHW tSA tHA NO MATCH MATCH DATAOUT"B" VALID tDC 5666 drw 09 NOTES: 1. CE0, BEn, and ADS = VIL; CE1, CNTEN, and REPEAT = VIH. 2. OE = VIL for Port "B", which is being read from. OE = VIH for Port "A", which is being written to. 3. If tCO < minimum specified, then data from Port "B" read is not valid until following Port "B" clock cycle (ie, time from write to valid read on opposite port will be tCO + 2 tCYC2 + tCD2 ). If tCO > minimum, then data from Port "B" read is available on first Port "B" clock cycle (ie, time from write to valid read on opposite port will be tCO + t CYC2 + t CD2). 4. All timing is the same for Left and Right ports. Port "A" may be either Left or Right port. Port "B" is the opposite of Port "A" Timing Waveform with Port-to-Port Flow-Through Read (1,2,4) CLK "A" tSW tHW tSA tHA R/W "A" ADDRESS "A" tSD DATAIN "A" NO MATCH MATCH tHD VALID tCO (3) CLK "B" tCD1 R/W "B" ADDRESS "B" tSW tHW tSA tHA NO MATCH MATCH tCD1 DATAOUT "B" VALID VALID tDC tDC 5666 drw 10 NOTES: 1. CE0, BEn, and ADS = VIL; CE1, CNTEN, and REPEAT = VIH. 2. OE = VIL for the Right Port, which is being read from. OE = VIH for the Left Port, which is being written to. 3. If tCO < minimum specified, then data from Port "B" read is not valid until following Port "B" clock cycle (i.e., time from write to valid read on opposite port will be tCO + tCYC + tCD1). If tCO > minimum, then data from Port "B" read is available on first Port "B" clock cycle (i.e., time from write to valid read on opposite port will be tCO + t CD1). 4. All timing is the same for both left and right ports. Port "A" may be either left or right port. Port "B" is the opposite of Port "A". 6.42 15 IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges Timing Waveform of Pipelined Read-to-Write-to-Read tCYC2 (OE = VIL)(2) tCH2 tCL2 CLK CE0 tSC tHC tSB tHB CE1 BEn tSW tHW R/W (3) ADDRESS tSW tHW An tSA tHA An +1 An + 2 An + 3 An + 2 An + 4 tSD tHD DATAIN Dn + 2 tCD2 (1) tCKHZ tCKLZ tCD2 Qn + 3 Qn DATAOUT READ NOP (4) WRITE READ 5666 drw 11 NOTES: 1. Output state (High, Low, or High-impedance) is determined by the previous cycle control signals. 2. CE 0, BEn, and ADS = VIL; CE1, CNTEN, and REPEAT = VIH. "NOP" is "No Operation". 3. Addresses do not have to be accessed sequentially since ADS = VIL constantly loads the address on the rising edge of the CLK; numbers are for reference use only. 4. "NOP" is "No Operation." Data in memory at the selected address may be corrupted and should be re-written to guarantee data integrity. Timing Waveform of Pipelined Read-to-Write-to-Read ( OE Controlled) (2) tCH2 tCYC2 tCL2 CLK CE0 tSC tHC tSB tHB CE1 BEn tSW tHW R/W tSW tHW (3) ADDRESS An tSA tHA An +1 An + 2 tSD DATAIN Dn + 2 tCD2 (1) Qn DATAOUT An + 3 An + 4 An + 5 tHD Dn + 3 tCKLZ tCD2 Qn + 4 (4) tOHZ OE READ WRITE READ 5666 drw 12 NOTES: 1. Output state (High, Low, or High-impedance) is determined by the previous cycle control signals. 2. CE0, BEn, and ADS = VIL; CE1, CNTEN, and REPEAT = VIH. 3. Addresses do not have to be accessed sequentially since ADS = VIL constantly loads the address on the rising edge of the CLK; numbers are for reference use only. 4. This timing does not meet requirements for fastest speed grade. This waveform indicates how logically it could be done if timing so allows. 6.42 16 IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges Timing Waveform of Flow-Through Read-to-Write-to-Read ( OE = VIL)(2) tCH1 tCYC1 tCL1 CLK CE0 tSC tHC tSB tHB CE1 BEn tSW tHW R/W tSW tHW (3) ADDRESS tSA An tHA An +1 An + 2 An + 4 An + 3 An + 2 tSD tHD DATAIN Dn + 2 tCD1 (1) tCD1 Qn DATAOUT tCD1 tCD1 Qn + 1 tDC tCKHZ (5) NOP READ tCKLZ WRITE Qn + 3 tDC READ 5666 drw 13 Timing Waveform of Flow-Through Read-to-Write-to-Read (OE Controlled)(2) tCYC1 tCH1 tCL1 CLK CE0 tSC tHC CE1 tSB tHB BEn tSW tHW tSW tHW R/W (3) An tSA tHA ADDRESS An +1 DATAIN (1) DATAOUT An + 2 tSD tHD An + 3 Dn + 2 Dn + 3 tDC tCD1 An + 4 tOE tCD1 Qn tCKLZ tOHZ An + 5 tCD1 Qn + 4 tDC OE READ WRITE READ 5666 drw 14 NOTES: 1. Output state (High, Low, or High-impedance) is determined by the previous cycle control signals. 2. CE 0, BEn, and ADS = VIL; CE1, CNTEN, and REPEAT = VIH. 3. Addresses do not have to be accessed sequentially since ADS = VIL constantly loads the address on the rising edge of the CLK; numbers are for reference use only. 4. "NOP" is "No Operation." Data in memory at the selected address may be corrupted and should be re-written to guarantee data integrity. 6.42 17 IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges Timing Waveform of Pipelined Read with Address Counter Advance tCH2 (1) tCYC2 tCL2 CLK tSA ADDRESS tHA An tSAD tHAD ADS tSAD tHAD CNTEN tSCN tHCN tCD2 DATAOUT Qx - 1(2) Qn + 2(2) Qn + 1 Qn Qx Qn + 3 tDC READ EXTERNAL ADDRESS READ WITH COUNTER COUNTER HOLD READ WITH COUNTER 5666 drw 15 Timing Waveform of Flow-Through Read with Address Counter Advance tCH1 tCYC1 tCL1 CLK tSA ADDRESS tHA An tSAD tHAD ADS tSAD tHAD tSCN tHCN CNTEN tCD1 DATAOUT Qx(2) Qn Qn + 1 Qn + 2 Qn + 3(2) Qn + 4 tDC READ EXTERNAL ADDRESS READ WITH COUNTER COUNTER HOLD READ WITH COUNTER 5666 drw 16 NOTES: 1. CE0, OE, BEn = VIL; CE1, R/W, and REPEAT = V IH. 2. If there is no address change via ADS = V IL (loading a new address) or CNTEN = VIL (advancing the address), i.e. ADS = VIH and CNTEN = VIH, then the data output remains constant for subsequent clocks. 6.42 18 (1) IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges Timing Waveform of Write with Address Counter Advance (Flow-through or Pipelined Inputs) (1) tCH2 tCYC2 tCL2 CLK tSA tHA An ADDRESS INTERNAL(3) ADDRESS An(7) An + 2 An + 1 An + 4 An + 3 tSAD tHAD ADS tSCN tHCN CNTEN tSD tHD Dn + 1 Dn DATAIN WRITE EXTERNAL ADDRESS Dn + 1 Dn + 3 Dn + 2 WRITE WRITE WITH COUNTER COUNTER HOLD Timing Waveform of Counter Repeat Dn + 4 WRITE WITH COUNTER 5666 drw 17 (2,6) tCYC2 CLK tSA tHA An ADDRESS (3) INTERNAL ADDRESS An+2 An+1 An An+2 An An+1 An+2 An+2 tSAD tHAD ADS tSW tHW R/W tSCN tHCN CNTEN REPEAT (4) tSRPT tHRPT tSD tHD DATAIN D0 D3 D2 D1 tCD1 An DATAOUT WRITE TO ADS ADDRESS An ADVANCE COUNTER WRITE TO An+1 ADVANCE COUNTER WRITE TO An+2 HOLD COUNTER WRITE TO An+2 REPEAT READ LAST ADS ADDRESS An An+1 An+2 An+2 , ADVANCE COUNTER READ An+1 ADVANCE COUNTER READ An+2 HOLD COUNTER READ An+2 5666 drw 18 NOTES: 1. CE 0, BEn, and R/W = VIL; CE1 and REPEAT = VIH. 2. CE 0, BEn = VIL; CE1 = VIH. 3. The "Internal Address" is equal to the "External Address" when ADS = VIL and equals the counter output when ADS = VIH. 4. No dead cycle exists during REPEAT operation. A READ or WRITE cycle may be coincidental with the counter REPEAT cycle: Address loaded by last valid ADS load will be accessed. For more information on REPEAT function refer to Truth Table II. 5. CNTEN = VIL advances Internal Address from `An' to `An +1'. The transition shown indicates the time required for the counter to advance. The `An +1'Address is written to during this cycle. 6. For Pipelined Mode user should add 1 cycle latency for outputs as per timing waveform of read cycle for pipelined operations. 6.42 19 IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Waveform of Interrupt Timing Industrial and Commercial Temperature Ranges (2) CLKL tSW tHW tSA tHA R/WL ADDRESSL(3) 3FFFF tSC CEL tHC (1) tINS INTR tINR CLKR tSC tHC CER(1) R/WR ADDRESSR(3) tSW tHW tSA tHA 3FFFF NOTES: 1. CE0 = VIL and CE 1 = VIH 2. All timing is the same for Left and Right ports. 3. Address is for internal register, not the external bus, i.e., address needs to be qualified by one of the Address counter control signals. Truth Table III -- Interrupt Flag (1) Left Port CLKL R/WL (2) CEL (2) 5666 drw 19 Right Port A17L-A0L (3,4,5) INTL CLKR R/WR CER(2) (2) A17R-A0R(3,4,5) INTR Function L L 3FFFF X X X X L Set Right INTR Flag X X X X H L 3FFFF H Reset Right INTR Flag X X X L L L 3FFFE X Set Left INTL Flag H L 3FFFE H X X X X Reset Left INTL Flag NOTES: 1. INTL and INTR must be initialized at power-up by Resetting the flags. 2. CE0 = VIL and CE 1 = VIH. R/W and CE are synchronous with respect to the clock and need valid set-up and hold times. 3. A17X is a NC for IDT70T3599, therefore Interrupt Addresses are 1FFFF and 1FFFE. 4. A17X and A16X are NC's for IDT70T3589, therefore Interrupt Addresses are FFFF and FFFE. 5. Address is for internal register, not the external bus, i.e., address needs to be qualified by one of the Address counter control signals. 6.42 20 5666 tbl 12 IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges Waveform of Collision Timing(1,2) Both Ports Writing with Left Port Clock Leading CLKL tOFS tSA (4) tHA ADDRESSL A3 A2 A1 A0 tCOLR tCOLS COLL (3) tOFS CLKR tSA tHA (4) ADDRESSR A0 A3 A2 A1 tCOLR tCOLS COLR 5666 drw 20 NOTES: 1. CE0 = VIL, CE1 = VIH. 2. For reading port, OE is a Don't care on the Collision Detection Logic. Please refer to Truth Table IV for specific cases. 3. Leading Port Output flag might output 3tCYC2 + tCOLS after Address match. 4. Address is for internal register, not the external bus, i.e., address needs to be qualified by one of the Address counter control signals. Collision Detection Timing(3,4) tOFS (ns) Cycle Time Region 1 (ns) (1) Region 2 (ns) 5ns 0 - 2.8 2.81 - 4.6 6ns 0 - 3.8 3.81 - 5.6 7.5ns 0 - 5.3 5.31 - 7.1 NOTES: 1. Region 1 Both ports show collision after 2nd cycle for Addresses 0, 2, 4 etc. 2. Region 2 Leading port shows collision after 3rd cycle for addresses 0, 3, 6, etc. while trailing port shows collision after 2nd cycle for addresses 0, 2, 4 etc. 3. All the production units are tested to midpoint of each region. 4. These ranges are based on characterization of a typical device. (2) 5666 tbl 13 Truth Table IV -- Collision Detection Flag Left Port Right Port CLKL R/WL(1) CEL(1) A17L-A0L(2) COLL CLKR R/WR(1) CE R(1) A17R-A0R(2) COLR Function H L MATCH H H L MATCH H Both ports reading. Not a valid collision. No flag output on either port. H L MATCH L L L MATCH H Left port reading, Right port writing. Valid collision, flag output on Left port. L L MATCH H H L MATCH L Right port reading, Left port writing. Valid collision, flag output on Right port. L L MATCH L L L MATCH L Both ports writing. Valid collision. Flag output on both ports. NOTES: 1. CE 0 = VIL and CE1 = VIH. R/W and CE are synchronous with respect to the clock and need valid set-up and hold times. 2. Address is for internal register, not the external bus, i.e., address needs to be qualified by one of the Address counter control signals. 6.42 21 5666 tbl 14 IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges Timing Waveform - Entering Sleep Mode (1,2) R/W (3) Timing Waveform - Exiting Sleep Mode (1,2) An An+1 (5) R/W OE (5) Dn DATAOUT Dn+1 (4) NOTES: 1. CE1 = V IH. 2. All timing is same for Left and Right ports. 3. CE0 has to be deactivated (CE0 = VIH) three cycles prior to asserting ZZ (ZZx = VIH) and held for two cycles after asserting ZZ (ZZx = V IH). 4. CE0 has to be deactivated (CE0 = VIH) one cycle prior to de-asserting ZZ (ZZx = VIL) and held for three cycles after de-asserting ZZ (ZZx = VIL). 5. The device must be in Read Mode (R/W High) when exiting sleep mode. Outputs are active but data is not valid until the following cycle. 6.42 22 IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Functional Description The IDT70T3519/99/89 provides a true synchronous Dual-Port Static RAM interface. Registered inputs provide minimal set-up and hold times on address, data, and all critical control inputs. All internal registers are clocked on the rising edge of the clock signal, however, the self-timed internal write pulse width is independent of the cycle time. An asynchronous output enable is provided to ease asynchronous bus interfacing. Counter enable inputs are also provided to stall the operation of the address counters for fast interleaved memory applications. A HIGH on CE0 or a LOW on CE1 for one clock cycle will power down the internal circuitry to reduce static power consumption. Multiple chip enables allow easier banking of multiple IDT70T3519/99/89s for depth expansion configurations. Two cycles are required with CE0 LOW and CE1 HIGH to re-activate the outputs. Interrupts If the user chooses the interrupt function, a memory location (mail box or message center) is assigned to each port. The left port interrupt flag (INTL) is asserted when the right port writes to memory location 3FFFE (HEX), where a write is defined as CER = R/WR = VIL per the Truth Table. The left port clears the interrupt through access of address location 3FFFE when CEL = VIL and R/WL = VIH. Likewise, the right port interrupt flag (INT R ) is asserted when the left port writes to memory location 3FFFF (HEX) and to clear the interrupt flag (INTR), the right port must read the memory location 3FFFF (1FFFF or 1FFFE for IDT70T3599 and FFFF or FFFE for IDT70T3589). The message (36 bits) at 3FFFE or 3FFFF (1FFFF or 1FFFE for IDT70T3599 and FFFF or FFFE for IDT70T3589) is user-defined since it is an addressable SRAM location. If the interrupt function is not used, address locations 3FFFE and 3FFFF (1FFFF or 1FFFE for IDT70T3599 and FFFF or FFFE for IDT70T3589) are not used as mail boxes, but as part of the random access memory. Refer to Truth Table III for the interrupt operation. Collision Detection Collision is defined as an overlap in access between the two ports resulting in the potential for either reading or writing incorrect data to a specific address. For the specific cases: (a) Both ports reading - no data is corrupted, lost, or incorrectly output, so no collision flag is output on either port. (b) One port writing, the other port reading - the end result of the write will still be valid. However, the reading port might capture data that is in a state of transition and hence the reading port's collision flag is output. (c) Both ports writing - there is a risk that the two ports will interfere with each other, and the data stored in memory will not be a valid write from either port (it may essentially be a random combination of the two). Therefore, the collision flag is output on both ports. Please refer to Truth Table IV for all of the above cases. The alert flag (COLX) is asserted on the 2nd or 3rd rising clock edge of the affected port following the collision, and remains low for one cycle. Please refer to Collision Detection Timing table on Page 21. During that next cycle, the internal arbitration is engaged in resetting the alert flag (this avoids a specific requirement on the part of the user to reset the alert flag). If two collisions occur on subsequent clock cycles, the second collision may not generate the appropriate alert Industrial and Commercial Temperature Ranges flag. A third collision will generate the alert flag as appropriate. In the event that a user initiates a burst access on both ports with the same starting address on both ports and one or both ports writing during each access (i.e., imposes a long string of collisions on contiguous clock cycles), the alert flag will be asserted and cleared every other cycle. Please refer to the Collision Detection timing waveform on Page 21.Collision detection on the IDT70T3519/99/89 represents a significant advance in functionality over current sync multi-ports, which have no such capability. In addition to this functionality the IDT70T3519/99/89 sustains the key features of bandwidth and flexibility. The collision detection function is very useful in the case of bursting data, or a string of accesses made to sequential addresses, in that it indicates a problem within the burst, giving the user the option of either repeating the burst or continuing to watch the alert flag to see whether the number of collisions increases above an acceptable threshold value. Offering this function on chip also allows users to reduce their need for arbitration circuits, typically done in CPLD's or FPGA's. This reduces board space and design complexity, and gives the user more flexibility in developing a solution. Sleep Mode The IDT70T3519/99/89 is equipped with an optional sleep or low power mode on both ports. The sleep mode pin on both ports is asynchronous and active high. During normal operation, the ZZ pin is pulled low. When ZZ is pulled high, the port will enter sleep mode where it will meet lowest possible power conditions. The sleep mode timing diagram shows the modes of operation: Normal Operation, No Read/Write Allowed and Sleep Mode. For normal operation all inputs must meet setup and hold times prior to sleep and after recovering from sleep. Clocks must also meet cycle high and low times during these periods. Three cycles prior to asserting ZZ (ZZx = VIH) and three cycles after de-asserting ZZ (ZZx = VIL), the device must be disabled via the chip enable pins. If a write or read operation occurs during these periods, the memory array may be corrupted. Validity of data out from the RAM cannot be guaranteed immediately after ZZ is asserted (prior to being in sleep). When exiting sleep mode, the device must be in Read mode (R/Wx = VIH)when chip enable is asserted, and the chip enable must be valid for one full cycle before a read will result in the output of valid data. During sleep mode the RAM automatically deselects itself. The RAM disconnects its internal clock buffer. The external clock may continue to run without impacting the RAMs sleep current (IZZ). All outputs will remain in high-Z state while in sleep mode. All inputs are allowed to toggle. The RAM will not be selected and will not perform any reads or writes. 6.42 23 IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges Depth and Width Expansion The IDT70T3519/99/89 features dual chip enables (refer to Truth Table I) in order to facilitate rapid and simple depth expansion with no requirements for external logic. Figure 4 illustrates how to control the various chip enables in order to expand two devices in depth. The IDT70T3519/99/89 can also be used in applications requiring expanded width, as indicated in Figure 4. Through combining the control signals, the devices can be grouped as necessary to accommodate applications needing 72-bits or wider. A18/A17/A16 IDT70T3519/99/89 CE0 CE1 CE0 CE1 VDD VDD Control Inputs Control Inputs IDT70T3519/99/89 IDT70T3519/99/89 CE1 IDT70T3519/99/89 CE0 CE0 Control Inputs CE1 Control Inputs Figure 4. Depth and Width Expansion with IDT70T3519/99/89 5666 drw 23 NOTE: 1. A18 is for IDT70T3519, A17 is for IDT70T3599, A16 is for IDT70T3589. 6.42 24 BE, R/W, OE, CLK, ADS, REPEAT, CNTEN , IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges JTAG Timing Specifications tJF tJCL tJCYC tJR tJCH TCK Device Inputs(1)/ TDI/TMS tJS Device Outputs(2)/ TDO tJDC tJH tJRSR tJCD TRST , 5666 drw 24 tJRST Figure 5. Standard JTAG Timing NOTES: 1. Device inputs = All device inputs except TDI, TMS, and TRST. 2. Device outputs = All device outputs except TDO. JTAG AC Electrical Characteristics (1,2,3,4) 70T3519/99/89 Symbol Parameter Min. Max. Units ns tJCYC JTAG Clock Input Period 100 ____ tJCH JTAG Clock HIGH 40 ____ ns tJCL JTAG Clock Low 40 ____ ns tJR JTAG Clock Rise Time ____ 3(1) ns JTAG Clock Fall Time ____ (1) 3 ns 50 ____ ns ns tJF tJRST JTAG Reset tJRSR JTAG Reset Recovery 50 ____ tJCD JTAG Data Output ____ 25 ns tJDC JTAG Data Output Hold 0 ____ ns tJS JTAG Setup 15 ____ ns 15 ____ tJH JTAG Hold ns 5666 tbl 15 NOTES: 1. Guaranteed by design. 2. 30pF loading on external output signals. 3. Refer to AC Electrical Test Conditions stated earlier in this document. 4. JTAG operations occur at one speed (10MHz). The base device may run at any speed specified in this datasheet. 6.42 25 IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges Identification Register Definitions Instruction Field Value Revision Number (31:28) IDT Device ID (27:12) Description 0x0 Reserved for version number (1) Defines IDT part number 0x330 IDT JEDEC ID (11:1) 0x33 ID Register Indicator Bit (Bit 0) Allows unique identification of device vendor as IDT 1 Indicates the presence of an ID register 5666 tbl 16 NOTE: 1. Device ID for IDT70T3599 is 0x331. Device ID for IDT70T3589 is 0x332. Scan Register Sizes Register Name Bit Size Instruction (IR) 4 Bypass (BYR) 1 Identification (IDR) Boundary Scan (BSR) 32 Note (3) 5666 tbl 17 System Interface Parameters Instruction Code Description EXTEST 0000 Forces contents of the boundary scan cells onto the device outputs (1). Places the boundary scan register (BSR) between TDI and TDO. BYPASS 1111 Places the bypass register (BYR) between TDI and TDO. IDCODE 0010 Loads the ID register (IDR) with the vendor ID code and places the register between TDI and TDO. 0100 Places the bypass register (BYR) between TDI and TDO. Forces all device output drivers to a High-Z state except COLx & INTx outputs. HIGHZ Uses BYR. Forces contents of the boundary scan cells onto the device outputs. Places the bypass register (BYR) between TDI and TDO. CLAMP 0011 SAMPLE/PRELOAD 0001 Places the boundary scan register (BSR) between TDI and TDO. SAMPLE allows data from device inputs (2) to be captured in the boundary scan cells and shifted serially through TDO. PRELOAD allows data to be input serially into the boundary scan cells via the TDI. 0101, 0111, 1000, 1001, 1010, 1011, 1100 Several combinations are reserved. Do not use codes other than those identified above. RESERVED PRIVATE 0110,1110,1101 For internal use only. 5666 tbl 18 NOTES: 1. Device outputs = All device outputs except TDO. 2. Device inputs = All device inputs except TDI, TMS, and TRST. 3. The Boundary Scan Descriptive Language (BSDL) file for this device is available on the IDT website (www.idt.com), or by contacting your local IDT sales representative. 6.42 26 IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges Ordering Information XXXXX A 999 A Device Type Power Speed Package A A Process/ Temperature Range Blank I G (3) Commercial (0C to +70C) Industrial (-40C to +85C) Green BC DR BF 256-pin BGA (BC-256) 208-pin PQFP (DR-208) 208-pin fpBGA (BF-208) 200 166 133 Commercial Only(2) Commercial & Industrial(1) Speed in Megahertz Commercial & Industrial S Standard Power 70T3519 9Mbit (256K x 36) 2.5V Synchronous Dual-Port RAM 70T3599 4Mbit (128K x 36) 2.5V Synchronous Dual-Port RAM 70T3589 2Mbit (64K x 36) 2.5V Synchronous Dual-Port RAM NOTES: 1. 166MHz I-Temp is only available in the BC-256 package. 2. 200Mhz is only available in the BC-256 package. 3. Green parts available. For specific speeds, packages and powers contact your local sales office. 5666 drw 25 IDT Clock Solution for IDT70T3519/99/89 Dual-Port Dual-Port I/O Specitications IDT Dual-Port Part Number Voltage 70T3519/99/89 2.5 Clock Specifications I/O Input Capacitance Input Duty Cycle Requirement Maximum Frequency Jitter Tolerance IDT PLL Clock Device IDT Non-PLL Clock Device LVTTL 8pF 40% 200 75ps 5T2010 5T9010 5T905, 5T9050 5T907, 5T9070 5666 tbl 19 6.42 27 IDT70T3519/99/89S High-Speed 2.5V 256/128/64K x 36 Dual-Port Synchronous Static RAM Industrial and Commercial Temperature Ranges Datasheet Document History: 01/23/03: 01/30/03: 04/25/03: 11/11/03: 03/30/04: 04/22/04: 04/12/05: 02/07/06: 04/10/06: 07/28/08: 01/19/09: Page 1 Page 11 Page 12 Page 10 Page 12 Page 21 Page 22 Page 26 Page 27 Page 22 & 23 Page 1 & 27 Page 6 Page 27 Page 1 & 28 Page 1 Page 27 Page 7 Page 1,3 & 12 Page 10 Page 27 Initial Datasheet Corrected 208-pin package from TQFP to PQFP Added Capacitance Derating drawing Changed tINS and tINR specs in AC Electrical Characteristics table Updated power numbers in DC Electrical Characteristics table Added tOFS symbol and parameter to AC Electrical Characteristics table Updated Collision Timing waveform Added Collision DetectionTiming table and footnotes Updated HIGHZ function in System Interface Parameters table Added IDT Clock Solution table Clarified Sleep Mode Text and Waveforms Removed Preliminary status Added another sentence to footnote 4 to recommend that boundary scan not be operated during sleep mode Clarified footnotes 1 & 2 for the ordering information Replaced old IDT TM with new IDT TM logo Added green availability to features Added green indicator to ordering information Changed footnote 2 for Truth Table I from ADS, CNTEN, REPEAT = VIH to ADS, CNTEN, REPEAT = X Changed FTx/PLx to PLx/FTx on diagrams and Notes. Corrected a typo in the footnotes of DC Chars table Removed "IDT" from orderable part number CORPORATE HEADQUARTERS 6024 Silver Creek Valley Road San Jose, CA 95138 for SALES: 800-345-7015 or 408-284-8200 fax: 408-284-2775 www.idt.com The IDT logo is a registered trademark of Integrated Device Technology, Inc. 6.42 28 for Tech Support: 408-284-2794 DualPortHelp@idt.com