Is Now Part of To learn more about ON Semiconductor, please visit our website at www.onsemi.com Please note: As part of the Fairchild Semiconductor integration, some of the Fairchild orderable part numbers will need to change in order to meet ON Semiconductor's system requirements. Since the ON Semiconductor product management systems do not have the ability to manage part nomenclature that utilizes an underscore (_), the underscore (_) in the Fairchild part numbers will be changed to a dash (-). This document may contain device numbers with an underscore (_). Please check the ON Semiconductor website to verify the updated device numbers. The most current and up-to-date ordering information can be found at www.onsemi.com. Please email any questions regarding the system integration to Fairchild_questions@onsemi.com. ON Semiconductor and the ON Semiconductor logo are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor's product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. "Typical" parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. FSFR-HS Series -- Advanced Fairchild Power Switch (FPSTM) for Half-Bridge Resonant Converters Features Description Variable Frequency Control with 50% Duty Cycle for Half-Bridge Resonant Converter Topology High Efficiency through Zero Voltage Switching (ZVS) Built-in High-Side Gate Driver IC Internal UniFETTMs with Fast-Recovery Type Body Diode (trr=160 ns Typical) Fixed Dead Time (350 ns) Optimized for MOSFETs Operating Frequency Up to 600 kHz for Soft-Start Self Auto-Restart Operation for All Protections, Despite External LVCC Bias Line UVLO with Programmable Hysteresis Level Simple On/Off with Line UVLO Pin Easy Configuration and Compatibility with FAN7930 for Line UVLO without External Components Protection Functions: Over-Voltage Protection (OVP), Over-Current Protection (OCP), Abnormal OverCurrent Protection (AOCP), Internal Thermal Shutdown (TSD) The FSFR-HS is a highly integrated power switch designed for high-efficiency half-bridge resonant converters. Offering everything necessary to build a reliable and robust resonant converter, the FSFR-HS simplifies designs while improving productivity and performance. The FSFR-HS combines power MOSFETs, a high-side gate-drive circuit, an accurate currentcontrolled oscillator, and built-in protection functions. The high-side gate-drive circuit has a common-mode noise cancellation capability, which provides stable operation with excellent noise immunity. Using zerovoltage-switching (ZVS) technique dramatically reduces the switching losses and significantly improves efficiency. The ZVS also reduces the switching noise noticeably, even though the operating frequency increases. It allows a small Electromagnetic Interference (EMI) filter, besides the high operating frequency, to reduce the volume of the resonant tank and to increase power density. The FSFR-HS can be applied to resonant converter topologies such as series resonant, parallel resonant, and LLC resonant converters. Applications Related Resources PDP and LCD TVs Desktop PCs and Servers Adapters Telecom Power Supplies AN4151 -- Half-Bridge LLC Resonant Converter Design Using FSFR-Series Fairchild Power Switch (FPSTM) Ordering Information Part Number Package FSFR1800HS 9-SIP FSFR1800HSL 9-SIP L-Forming FSFR1700HS 9-SIP FSFR1700HSL 9-SIP L-Forming Operating Maximum Output Power Maximum Output Junction RDS(ON_MAX) without Heatsink Power with Heatsink Temperature (VIN=350~400 V)(1,2) (VIN=350~400 V)(1,2) -40 to +130C 0.95 120 W 260 W -40 to +130C 1.25 100 W 200 W Notes: 1. The junction temperature can limit the maximum output power. 2. Maximum practical continuous power in an open-frame design at 50C ambient. (c) 2011 Fairchild Semiconductor Corporation FSFR1800 / FSFR1700-HS * Rev.1.0.1 www.fairchildsemi.com FSFR-HS Series -- Advanced Fairchild Power Switch (FPSTM) for Half-Bridge Resonant Converter February 2013 FSFR-HS Series -- Advanced Fairchild Power Switch (FPSTM) for Half-Bridge Resonant Converter Application Circuit Diagram Figure 1. Typical Application Circuit (LLC Resonant Half-Bridge Converter) Block Diagram Figure 2. Internal Block Diagram (c) 2011 Fairchild Semiconductor Corporation FSFR1800 / FSFR1700-HS * Rev.1.0.1 www.fairchildsemi.com 2 Figure 3. Package Diagram Pin Definitions Pin # Name Description 1 DL This is the drain of the high-side MOSFET, typically connected to the input DC link voltage. 2 LS This is the line-sensing pin for the input voltage Under-Voltage Lockout (UVLO). 3 RT This pin is used for controlling the switching frequency in normal operation. When any protections are triggered, the internal Auto/Restart (A/R) circuit starts to sense the voltage on the pin, which is discharged naturally by external resistance. The IC can be operated with A/R when the voltage decreases 0.1 V. Typically, an opto-coupler is connected to control the switching frequency for the output voltage regulation and resistors for setting minimum / maximum operating frequency. 4 CS This pin senses the current flowing through the low-side MOSFET. Typically, negative voltage is applied to this pin. 5 SG This pin is the ground of the control part. 6 PG This pin is the power ground. This pin is connected to the source of the low-side MOSFET. 7 LVCC 8 NC 9 HVCC This is the supply voltage of the high-side gate-drive circuit. 10 CTR This is the drain of the low-side MOSFET. Typically, a transformer is connected to this pin. This pin is the supply voltage of the control IC. No connection (c) 2011 Fairchild Semiconductor Corporation FSFR1800 / FSFR1700-HS * Rev.1.0.1 www.fairchildsemi.com 3 FSFR-HS Series -- Advanced Fairchild Power Switch (FPSTM) for Half-Bridge Resonant Converter Pin Configuration Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only. Symbol Parameter Min. Max. Unit VDS Maximum Drain-to-Source Voltage (DL-CTR and CTR-PG) 500 LVCC Low-Side Supply Voltage -0.3 25.0 V -0.3 25.0 V HVCC to CTR High-Side VCC Pin to Low-Side Drain Voltage HVCC V High-Side Floating Supply Voltage -0.3 525.0 V VRT Timing Resistor Connecting and Auto-Restart Pin Voltage -0.3 5.0 V VLS Line Sensing Input Voltage -0.3 LVCC V VCS Current Sense (CS) Pin Input Voltage -5 1 V fsw Recommended Switching Frequency 10 600 kHz 50 V/ns dVCTR/dt PD TJ TSTG Allowable Low-Side MOSFET Drain Voltage Slew Rate Total Power Dissipation(4) FSFR1800HS/L 11.7 FSFR1700HS/L 11.6 Maximum Junction Temperature(5) W +150 Recommended Operating Junction Temperature (5) Storage Temperature Range -40 +130 -55 +150 C C MOSFET Section VDGR Drain Gate Voltage (RGS=1 M) VGS Gate Source (GND) Voltage IDM Drain Current Pulsed(6) 500 30 FSFR1800HS/L 23 FSFR1700HS/L 20 FSFR1800HS/L ID V Continuous Drain Current FSFR1700HS/L TC=25C 7.0 TC=100C 4.5 TC=25C 6.0 TC=100C 3.9 V A A Package Section Torque Recommended Screw Torque 5~7 kgf*cm Notes: 3. These parameters, although guaranteed, are tested only in EDS (wafer test) process. 4. Per MOSFET when both MOSFETs are conducting. 5. The maximum value of the recommended operating junction temperature is limited by thermal shutdown. 6. Pulse width is limited by maximum junction temperature. Thermal Impedance TA=25C unless otherwise specified. Symbol Parameter JC Junction-to-Case Center Thermal Impedance (Both MOSFETs Conducting) JA Junction-to-Ambient Thermal Impedance (c) 2011 Fairchild Semiconductor Corporation FSFR1800 / FSFR1700-HS * Rev.1.0.1 Value FSFR1800HS/L 10.7 FSFR1700HS/L 10.8 FSFR1800HS/L FSFR1700HS/L 80 Unit C/W C/W www.fairchildsemi.com 4 FSFR-HS Series -- Advanced Fairchild Power Switch (FPSTM) for Half-Bridge Resonant Converter Absolute Maximum Ratings TA=25C, LVCC, HVCC =17 VDC and RT=26 k unless otherwise specified. Symbol Parameter Conditions Min. Typ. Max. Unit MOSFET Section BVDSS Drain-to-Source Breakdown Voltage RDS(ON) On-State Resistance trr Body Diode Reverse (7) Recovery Time CISS Input Capacitance(7) COSS Output Capacitance(7) ID=200 A, TA=25C 500 V ID=200 A, TA=125C 540 FSFR1800HS/L VGS=10 V, ID=3.0 A 0.77 0.95 FSFR1700HS/L VGS=10 V, ID=2.0 A 1.00 1.25 FSFR1800HS/L VGS=0 V, IDIODE=7.0 A, dIDIODE/dt=100 A/s 160 FSFR1700HS/L VGS=0 V, IDIODE=6.0 A, dIDIODE/dt=100 A/s 160 ns FSFR1800HS/L 639 pF FSFR1700HS/L 512 pF 82.1 pF 66.5 pF VDS=25 V, VGS=0 V, f=1.0 MHz FSFR1800HS/L FSFR1700HS/L Supply Section HVCC=VCTR=500 V ILK Offset Supply Leakage Current IQHVCC Quiescent HVCC Supply Current (HVCCUV+) - 0.1 V 50 120 A IQLVCC Quiescent LVCC Supply Current (LVCCUV+) - 0.1 V 100 200 A IOHVCC Operating HVCC Supply Current (RMS Value) mA IOLVCC Operating LVCC Supply Current (RMS Value) 50 A fOSC=50 KHz 6 9 No Switching 100 200 A fOSC=50 KHz 7 11 mA No Switching 2 4 mA UVLO Section LVCCUV+ LVCC Supply Under-Voltage Positive Going Threshold (LVCC,START) 11.2 12.5 13.8 V LVCCUV- LVCC Supply Under-Voltage Negative Going Threshold (LVCC,STOP) 8.9 10.0 11.1 V HVCCUV+ HVCC Supply Under-Voltage Positive Going Threshold (HVCC,START) 8.2 9.2 10.2 V HVCC Supply Under-Voltage Negative Going Threshold (HVCC,STOP) 7.8 8.7 9.6 V LVCCUVH LVCC Supply Under-Voltage Hysteresis HVCCUV- 2.5 HVCCUVH HVCC Supply Under-Voltage Hysteresis V 0.5 V Oscillator & Feedback Section VRT Output Voltage on RT Pin fOSC Output Oscillation Frequency DC Output Duty Cycle RT=26 k 1.5 2.0 2.5 V 47 50 53 kHz 48 50 52 % Continued on the following page... (c) 2011 Fairchild Semiconductor Corporation FSFR1800 / FSFR1700-HS * Rev.1.0.1 www.fairchildsemi.com 5 FSFR-HS Series -- Advanced Fairchild Power Switch (FPSTM) for Half-Bridge Resonant Converter Electrical Characteristics TA=25C, LVCC, HVCC =17 VDC and RT=26 k unless otherwise specified. Symbol Parameter Conditions Min. Typ. Max. Unit 0.07 0.12 0.17 Protection Section VRT,RESET Threshold Voltage to Begin Restart tDELAY,RESET Delay to Disable OSC Circuit After Protection fosc=50 kHz 20 V ms VLINE On Threshold of Input Voltage 2.38 2.50 2.62 V ILINE Hysteresis Current for Line UVLO 7.5 9.5 11.5 A VOVP LVCC Over-Voltage Protection VAOCP AOCP Threshold Voltage (7) tBAO AOCP Blanking Time VOCP OCP Threshold Voltage 23 25 V -0.9 -0.8 V -0.64 -0.58 VCS < VAOCP (7) tBO OCP Blanking Time tDA Delay Time (Low-Side) Detecting from VAOCP to Switch Off(7) TSD 21 -1.0 VCS < VOCP (7) Thermal Shutdown Temperature 50 1.0 120 ns -0.52 V 1.5 2.0 s 250 400 ns 135 150 C Dead-Time Control Section DT Dead Time(8) 350 ns Notes: 7. This parameter, although guaranteed, is not tested in production. 8. These parameters, although guaranteed, are tested only in EDS (wafer test) process. (c) 2011 Fairchild Semiconductor Corporation FSFR1800 / FSFR1700-HS * Rev.1.0.1 www.fairchildsemi.com 6 FSFR-HS Series -- Advanced Fairchild Power Switch (FPSTM) for Half-Bridge Resonant Converter Electrical Characteristics (Continued) These characteristic graphs are normalized at TA=25C. 1.1 1.1 1.05 1.05 1 1 0.95 0.95 0.9 0.9 -50 -25 Figure 4. 0 25 50 75 -50 100 Low-Side MOSFET Duty Cycle vs. Temperature -25 0 25 50 75 100 Figure 5. Switching Frequency vs. Temperature 1.1 1.1 1.05 1.05 1 1 0.95 0.95 0.9 0.9 -50 -25 0 25 50 75 100 -50 Figure 6. High-Side VCC (HVCC) Start vs. Temperature -25 0 25 50 75 100 Figure 7. High-Side VCC (HVCC) Stop vs. Temperature 1.1 1.1 1.05 1.05 1 1 0.95 0.95 0.9 0.9 -50 -25 0 25 50 75 -50 100 Figure 8. Low-Side VCC (LVCC) Start vs. Temperature (c) 2011 Fairchild Semiconductor Corporation FSFR1800 / FSFR1700-HS * Rev.1.0.1 -25 0 25 50 75 100 Figure 9. Low-Side VCC (LVCC) Stop vs. Temperature www.fairchildsemi.com 7 FSFR-HS Series -- Advanced Fairchild Power Switch (FPSTM) for Half-Bridge Resonant Converter Typical Performance Characteristics 1.1 1.1 1.05 1.05 Normalized at 25OC Normalized at 25OC These characteristic graphs are normalized at TA=25C. 1 0.95 1 0.95 0.9 0.9 -50 -25 0 25 50 75 -50 100 -25 0 25 Temp (OC) 50 75 100 Temp (OC) Figure 10. LVCC OVP Voltage vs. Temperature Figure 11. RT Voltage vs. Temperature 1.1 Normalized at 25OC 1.05 1 0.95 0.9 -50 -25 0 25 50 75 100 Temp (OC) Figure 12. VRT,RESET vs. Temperature Figure 13. OCP Voltage vs. Temperature Figure 14. VLINE vs. Temperature Figure 15. ILINE vs. Temperature (c) 2011 Fairchild Semiconductor Corporation FSFR1800 / FSFR1700-HS * Rev.1.0.1 www.fairchildsemi.com 8 FSFR-HS Series -- Advanced Fairchild Power Switch (FPSTM) for Half-Bridge Resonant Converter Typical Performance Characteristics (Continued) These characteristic graphs are normalized at TA=25C. Figure 16. tDELAY,RESET vs. Temperature (c) 2011 Fairchild Semiconductor Corporation FSFR1800 / FSFR1700-HS * Rev.1.0.1 Figure 17. VRT,RESET vs. Temperature www.fairchildsemi.com 9 FSFR-HS Series -- Advanced Fairchild Power Switch (FPSTM) for Half-Bridge Resonant Converter Typical Performance Characteristics (Continued) 1. Basic Operation: FSFR-HS series is designed to drive high-side and low-side MOSFETs complementarily with 50% duty cycle. A fixed dead time of 350 ns is introduced between consecutive transitions, as shown in Figure 18. Assuming the saturation voltage of opto-coupler transistor is 0.2 V, the maximum switching frequency is determined as: f max = Once LVCC is higher than LVCC,START = 12.5 V, the IC starts to operate, generates the low-side gate signal, and drives the low-side MOSFET. The bootstrap diode and capacitor is charged by the low-side MOSFET's operation. After the voltage on HVCC increases up to HVCC,START, typically 9.2 V, the high-side gate signal is generated for the MOSFET. 1 [ Hz ] 792 p x Rmin || Rmax + 0.54 (2) Figure 18. MOSFET Gate Drive Signals 2. Internal Oscillator: FSFR-HS series employs a current-controlled oscillator, as shown in Figure 19. Internally, the voltage of the RT pin is regulated at 2 V and the charging / discharging current for the oscillator capacitor, CT, is obtained by copying the current flowing out of the RT pin (ICTC) using a current mirror. Therefore, the switching frequency increases as ICTC increases. Figure 20. Resonant Converter Typical Gain Curve Figure 19. Current-Controlled Oscillator 3. Frequency Setting: Figure 20 shows the typical voltage gain curve of a resonant converter, where the gain is inversely proportional to the switching frequency in the ZVS region. The output voltage can be regulated by modulating the switching frequency. Figure 21 shows the typical circuit configuration for the RT pin, where the opto-coupler transistor is connected to the RT pin to modulate the switching frequency. The switching frequency may be controlled from 20 kHz to 500 kHz. Figure 21. Frequency Control Circuit To prevent excessive inrush current and overshoot of output voltage during startup, the IC needs to increase the voltage gain of the resonant converter progressively. Since the voltage gain of the resonant converter is inversely proportional to the switching frequency, softstart is implemented by sweeping down the switching frequency from an initial high frequency (f I S S ) until the output voltage is established. The minimum switching frequency is determined as: f min = 1 792 p x Rmin + 0.54 [ Hz ] (c) 2011 Fairchild Semiconductor Corporation FSFR1800 / FSFR1700-HS * Rev.1.0.1 The soft-start circuit is constructed by connecting R-C series network to the RT pin, as shown in Figure 21. Initially, the operating frequency is set by the parallel impedance of RSS and Rmin. (1) www.fairchildsemi.com 10 FSFR-HS Series -- Advanced Fairchild Power Switch (FPSTM) for Half-Bridge Resonant Converter Functional Description f ss = 1 [ Hz ] 792 p x R min || R SS + 0.54 (3) The soft-start time, tSS, can be calculated by: tSS = 3 x RSS CSS [ s ] Once a fault condition is detected, switching is instantly terminated and the MOSFETs remain off. When LVCC falls to the LVCC stop voltage of 10 V and VRT is lower than VRT,RESET of 0.1 V, the protection is reset. The FSFR-HS resumes normal operation when LVCC reaches the start voltage of 12.5 V. (4) 4. Self Auto-Restart: The FSFR-HS series can restart automatically even though any built-in protections are triggered in case external supply voltage is applied. As shown in Figure 22 and Figure 23; once a protection is triggered, the power MOSFET immediately stops. The counter starts to operate and 1008-clocks are counted, then the V-I converter is disabled. CSS starts to be naturally discharged with the series impedance of RSS and Rmin until VRT drops to VRT,RESET, typically 0.1 V. Then, all protections are reset and the V-I converter resumes. The FSFR-HS starts switching again with soft-start. The counter operating time for 1008-clocks after protection activation is set by the current out of the RT pin until VRT drops to VRT,RESET. Finally, the stop time of FSFR-HS can be estimated, without considering the counter operation time, as: t STOP = 3 CSS (RSS + Rmin ) [ s ] (5) Figure 24. Protection Blocks 5.1 Over-Current Protection (OCP): When the sensing pin voltage drops below -0.58 V and its duration becomes more than OCP blanking time of 1.5 s, OCP is triggered and the MOSFETs remain off. 5.2 Abnormal Over-Current Protection (AOCP): If the secondary rectifier diodes are shorted, large current with extremely high di/dt can flow through the MOSFET before OCP is triggered. AOCP is triggered without shutdown delay if the sensing pin voltage drops below -0.9 V. 5.3 Over-Voltage Protection (OVP): When the LVCC reaches 23 V, OVP is triggered. This protection is used when auxiliary winding of the transformer supplies VCC to the FPSTM. Figure 22. Internal Block for Auto-Restart 5.4 Thermal Shutdown (TSD): The MOSFETs and the control IC in one package make it easier for the control IC to detect the abnormal over-temperature of the MOSFETs. If the temperature exceeds approximately 130C, thermal shutdown triggers. 6. Line Under-Voltage Lockout (UVLO): FSFR-HS includes precise line UVLO (or brownout) with programmable hysteresis voltage. This function can start or restart the IC when VLS for the scale-down voltage of the DC-link by the sensing resistors, R1 and R2, is higher than VLINE of 2.5 V as the DC-link voltage increases and vice versa. A hysteresis voltage between the start and stop voltage of the IC is programmable by ILINE. In normal operation, the comparator's output is HIGH and ILINE is deactivated so that a voltage on LS pin, VLS, can be obtained as a divided voltage by R1 and R2. On the contrary, ILINE is activated when the comparator's output is LOW. VLS is generated by the difference between the current through R1 and ILINE. Figure 23. Self Auto-Restart Operation (c) 2011 Fairchild Semiconductor Corporation FSFR1800 / FSFR1700-HS * Rev.1.0.1 www.fairchildsemi.com 11 FSFR-HS Series -- Advanced Fairchild Power Switch (FPSTM) for Half-Bridge Resonant Converter 5. Protection Circuits: The FSFR-HS series has several self-protective functions; such as Over-Current Protection (OCP), Abnormal Over-Current Protection (AOCP), OverVoltage Protection (OVP), Thermal Shutdown (TSD), and Line Under-Voltage Lockout (LUVLO or Brownout). These protections are Auto-Restart Mode protections, as shown in Figure 24. The initial maximum frequency can be set up to 600 kHz, which is given by: Cr Np Ns The start and stop input-voltage can be calculated as: R1 + R 2 [V ] R2 = Vdc-link ,STOP + I LINE x R1 [V ] Ns Vdc -link ,STOP = VLINE x (6) Vdc-link ,START (7) Control IC VCS I DS CS SG PG Rsense V CS IDS Figure 27. Half-Wave Sensing I DS Figure 25. Half-Wave Sensing VCS 7. Simple Remote-On/Off: The power stage can be shutdown with optional Auto-Restart Mode, as shown in Figure 26. Cr To configure an external protection with Auto-Restart Mode, an opto-coupler and the LS pin are used. When the voltage on the LS pin is pulled below VLINE (2.5 V), the IC stops during the status holds. However, the optocoupler stops pulling down and the IC can perform the auto-restart operation itself. Control IC VCS Np CS SG PG Rsense Ns Ns IDS Figure 28. Full-Wave Sensing 8.2 Capacitive Sensing Method: The drain current can be sensed using an additional capacitor parallel with the resonant capacitor, as shown in Figure 29. During the low-side switch turn on, the current, iCB through CB, makes VSENSE across RSENSE. The iCB is scale-down of ip by the impedance ratio of Cr and CB. Generally, 1/100~1/1000 is adequate for the ratio of CB against Cr. RD is used as a damper for reducing noise generated by switching transition. Several hundreds of ohm to a few of kilo-ohms can be normally used. Figure 26. External Protection Circuits VSENSE can be estimated as; Vsense = I Cr 8. Current-Sensing Methods: FSFR-HS series employs negative voltage sensing to detect the drain current of MOSFET, which allows a low-noise resistive sensing using a filter with low time-constant and capacitive sensing method. pk CB Rsense [V ] Cr (8) 8.1 Resistive Sensing Method: The IC can sense drain current as a negative voltage, as shown in Figure 27 and Figure 28. Half-wave sensing allows low power dissipation in the sensing resistor; while full-wave sensing has less switching noise in the sensing signal. For a time constant range for the filter, 3/100~1/10 of the operating frequency is reasonable. (c) 2011 Fairchild Semiconductor Corporation FSFR1800 / FSFR1700-HS * Rev.1.0.1 www.fairchildsemi.com 12 FSFR-HS Series -- Advanced Fairchild Power Switch (FPSTM) for Half-Bridge Resonant Converter CFilter can be used to reduce some noise induced from transformer or switching transition. Generally, hundreds of pico-farad to tens of nano-farad is adequate, depending on the quantity of noise. Figure 29. Capacitive Sensing Figure 30. Example of Duty Balancing (c) 2011 Fairchild Semiconductor Corporation FSFR1800 / FSFR1700-HS * Rev.1.0.1 www.fairchildsemi.com 13 FSFR-HS Series -- Advanced Fairchild Power Switch (FPSTM) for Half-Bridge Resonant Converter 9. PCB Layout Guidelines: Duty imbalance problems may occur due to the radiated noise from the main transformer, the inequality of the secondary side leakage inductances of main transformer, and so on. This is one of the reasons that the control components in the vicinity of the RT pin are enclosed by the primary current flow pattern on PCB layout. The direction of the magnetic field on the components caused by the primary current flow is changed when the high- and low-side MOSFET turn on by turns. The magnetic fields with opposite directions induce a current through, into, or out of the RT pin, which makes the turn-on duration of each MOSFET different. It is strongly recommended to separate the control components in the vicinity of the RT pin from the primary current flow pattern in the PCB layout. Figure 30 shows an example for a dutybalanced case. Figure 31. 9-Lead, Single Inline Package (SIP) Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild's worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. Always visit Fairchild Semiconductor's online packaging area for the most recent package drawings: http://www.fairchildsemi.com/packaging/. (c) 2011 Fairchild Semiconductor Corporation FSFR1800 / FSFR1700-HS * Rev.1.0.1 www.fairchildsemi.com 14 FSFR-HS Series -- Advanced Fairchild Power Switch (FPSTM) for Half-Bridge Resonant Converter Physical Dimensions FSFR-HS Series -- Advanced Fairchild Power Switch (FPSTM) for Half-Bridge Resonant Converter Physical Dimensions Figure 32. 9-Lead, Single Inline Package (SIP), L-Forming Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild's worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. Always visit Fairchild Semiconductor's online packaging area for the most recent package drawings: http://www.fairchildsemi.com/packaging/. (c) 2011 Fairchild Semiconductor Corporation FSFR1800 / FSFR1700-HS * Rev.1.0.1 www.fairchildsemi.com 15 FSFR-HS Series -- Advanced Fairchild Power Switch (FPSTM) for Half-Bridge Resonant Converter (c) 2011 Fairchild Semiconductor Corporation FSFR1800 / FSFR1700-HS * Rev.1.0.1 www.fairchildsemi.com 16 ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor's product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. "Typical" parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor 19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com (c) Semiconductor Components Industries, LLC N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5817-1050 www.onsemi.com 1 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative www.onsemi.com