PolySwitch Telecom and Network Resettable Fuses PolySwitch(R) devices for telecommunication and networking applications were initially designed over ten years ago to meet the growing demand for resettable overcurrent protection. These product families provide protection against power cross and power induction surge as defined in ITU, Telcordia, and UL. Available in chip, surface mount, and radial leaded configurations, PolySwitch devices help improve the reliability of customer premise and network equipment world wide. Applications: Features: * Resettable overcurrent protection * Surface mount, radial leaded, and chip form factors * Fast time to trip * Agency recognition, UL, CSA, TUV * Resistance sorted and matched devices available * Low parasitic capacitance / flat impedance with frequency Benefits: * Many product choices give engineers more design flexibility * Compatible with high volume electronics assembly * Modems * Assists in meeting regulatory requirements * Phone sets * Improved line balance * Fax machines * Applicable for legacy POTS and modern digital communications equipment * Phone wall outlets * Alarm systems * PBX systems * MDF modules * Analog and digital line cards * T1/E1 equipment * xDSL modems and splitters * Powered Ethernet systems * VoIP (Voice over IP equipment) * LAN, WAN equipment * Customer premise equipment * Access network hardware Among the new products featured within are: TSV A new surface mount device which occupies less board space for ITU applications. TSL A new surface mount device specifically designed to meet Telcordia intrabuilding specifications for VoIP applications and other LAN equipment. TSU600 A new surface mount device designed to meet UL1950/7A Mini PCI and compact modem applications. BBR550/BBR750 Two new radial leaded devices to meet broadband cable tap and set-top box applications. SMD030-2018 A new surface mount product specifically designed for powered Ethernet applications. Selection guide for telecom devices Step 1. Review the equipment specification table on the following page based on the agency specification required to qualify the final equipment. Use the selection table to narrow your product selection based on key device characteristics. Step 2. Verify that the PolySwitch device hold current will accommodate the telecom circuit's maximum ambient temperature and normal operating current. Look across the top of the Thermal Derating Table on page 4 to find the temperature that most closely matches the circuit's maximum operating temperature. Look down that column to find the value equal to or greater than the circuit's normal operating current. Now look to the far left of that row to find the part number for the PolySwitch telecom device that will best accommodate the circuit. Note: The Thermal Derating Curves located in figure T1 are the normalized representations of the data in the Thermal Derating Table. Step 3. Verify that the time to trip characteristic of the chosen device meets the protection requirements of the telecommunications equipment circuit. Time to trip is the amount of time it takes for a device to switch to a high resistance state once a fault current has been applied across the device. Identifying the PolySwitch device's time to trip is important in order to provide the desired protection capabilities. If the device you choose trips too fast, undesired or nuisance tripping will occur. If the device trips too slowly, the components being protected may be damaged before the device switches to a high resistance state. Refer to typical time to trip curves for each of the possible PolySwitch devices. If the PolySwitch device time to trip is too fast or too slow for the circuit, go back to Step 2 and choose an alternate device. Step 4. Verify ambient operating condition. Ensure that your application's minimum and maximum ambient temperatures are within the operating temperature of -40C to 85C. Step 5. Independently evaluate and test the device. PolySwitch devices can help your telecom equipment to meet agency requirements. To confirm your selection, independently evaluate and test the device to the application requirements. 1 Equipment/specification table To use this guide, follow the steps below: 1. Select your equipment type from the list on the left side of the equipment/protection application table. 2. Select the type of protection depending on the agency and regional specifications in the second column. 3. Note the Key Device Selection Criteria (Size, Resistance, Time to trip) to determine best suitability for your application. 4. Use the table on the next page (Agency specification/PolySwitch telecom device selection) to select a specific part number for each application based on the agency requirements. Application Customer premise equipment, IT equipment Analog modems, V.90 modems, ISDN modems, xDSL modems, ADSL splitters, phone sets, fax machines, answering machines, caller ID, internet appliances, PBX systems, POS terminals, wall plugs Region/Specification North America FCC Part 68, UL 1950, UL 1459 PolySwitch Resettable Fuses Key Device Selection Criteria Small Footprint Low Resistance Fast Time to Trip TR600-150-RA TR600-150-RB TR600-150 TS600-200-RA TS600-170 TS600-170 TSU600-180 TSU600-180 SiBar Thyristor Surge Protectors1 TVBxxxSA with TR/TS TVSxxxSC with fuse TVBxxxSA Europe/Asia/South America ITU K.21 TR250-120 TR250-145 TS250-130 TSV250-130 TR250-180U TS250-130-RA TSV250-130 TSU600-180 TR250-120T-R2 TS250-130-RB TR600-150-RA TS600-200-RA TR600-160-RA TS600-200-RA TR600-150-RB TS600-170 TR250-120 TR250-145 TS250-130 TSV250-130 TR250-180U TS250-130-RA TSV250-130 TSU600-180 TR250-120T-R2 TS250-130-RB TR600-150-RA TS600-200-RA TR600-160-RA TS600-200-RA TR600-150-RB TS600-170 TR250-120 TR250-145 TS250-130 TSV250-130 TR250-180U TS250-130-RA TSV250-130 TSU600-180 TR250-120T-R2 TS250-130-RB TVBxxxSC North America Telcordia GR-1089 Access network equipment (*) Remote terminals, line repeaters, multiplexers, cross-connects, WAN equipment Europe/Asia/South America ITU K.45 Central office switching equipment (*) Analog/POTS linecards, ISDN linecards, xDSL modems, ADSL/VDSL splitters, T1/E1 linecards, multiplexers, CSU/DSU, servers TVBxxxSA TVBxxxSC North America Telcordia GR-1089 Europe/Asia/South America ITU K.20 TVBxxxSA N/A Primary protection modules (*) MDF modules, Network Interface Devices (NID) North America Telcordia GR-974 TR250-180U TGC250-120T TR250-120T TS250-130 TSV250-130 TSL250-080 North America TR250-120 Telcordia GR-1089 TS250-130 intrabuilding TSV250-130 TR250-120 Europe/Asia/South America TR250-145 ITU K.21 TS250-130 TSV250-130 Europe/Asia/South America ITU K.20 Short-haul/intrabuilding communications equipment (*) LAN equipment, VoIP cards, cable telephony NIU's, wireless local loop handsets LAN intrabuilding power cross protection LAN equipment, VoIP cards, IP phones IEEE 802.3 Power over LAN protection Powered Ethernet switches and terminals, IP phones, wireless LAN base stations, microcellular base stations, VoIP cards Cable telephony powering systems Power passing taps TR250-180U TGC250-145T TR250-145-RA TS250-130-RA TSV250-130 TR250-145 TR250-180U TS250-130-RA TSV250-130 TR250-180U TS250-130-RA TSV250-130 TSU600-180 TR250-180U TGC250-120T TR250-120T-R2 TS250-130-RB N/A TVBxxxSA TR250-120T-R2 TSL250-080 TVBxxxSA TR250-120T-R2 TS250-130-RB TVBxxxSA TSL250-080 TSL250-080 TSL250-080 N/A miniSMDC014 SMD030-2018 SMD030 SMD030-2018 BBR550 BBR750 BBR550 N/A Note: This list is not exhaustive. Raychem Circuit Protection welcomes our customers' input for additional application ideas for PolySwitch resettable fuses. (*) For improved line balance in these applications, resistance binned parts are recommended. Use suffix -B-0.5 for binned parts. Note 1 - For more information on Raychem SiBar(R) Thyristor surge protectors see the Raychem Circuit Protection Databook or the Raychem Circuit Protection website: www.circuitprotection.com. 2 Agency specification/PolySwitch telecom device selection Use the table below to select the PolySwitch device which most closely fits your application criteria. The following pages contain the specifications for the part numbers recommended below. PolySwitch devices assist telecommunications equipment to meet the applicable protection requirements of these industry specifications. Refer to individual agency specifications for test procedures and circuit schematics. Family TC250 TGC250 Product (*) TGC250-120 TGC250-145 TC250-180 Lightning ITU K.20/21/45 - 1.5kV 10/700s ITU K.20/21/45 - 4.0kV 10/700s (**) Power Cross ITU K.20/21/45 - 230Vac, 10 ITU K.20/21/45 - 600Vac, 600 TR250 TR250-080U TR250-080T ITU K.20 - 1.0kV 10/700s ITU K.20 - 230Vac, 10 ITU K.20 - 600Vac, 600 TR250-110U TR250-120 TR250-120T TR250-120U TR250-120UT TR250-145 TR250-145U ITU K.20/21/45 - 1.5kV 10/700s ITU K.20/21/45 - 4.0kV 10/700s (**) ITU K.20/21/45 - 230Vac, 10 ITU K.20/21/45 - 600Vac, 600 TR250-180U ITU K.20/21/45 - 1.5kV 10/700s ITU K.20/21/45 - 4.0kV 10/700s (**) Telcordia GR-974 - 1.0kV, 10/1000s ITU K.20/21/45 - 230Vac, 10 ITU K.20/21/45 - 600Vac, 600 Telcordia GR-974 - 283Vac, 10A TS250 TSV250 TS250-130 TSV250-130 ITU K.20/21/45 - 1.5kV 10/700s ITU K.20/21/45 - 4.0kV 10/700s (**) ITU K.20/21/45 - 230Vac, 10 ITU K.20/21/45 - 600Vac, 600 TSL TSL250-080 Telcordia GR-1089 Intrabuilding -Surge 1 & 2 Telcordia GR-1089 Intrabuilding - 120Vac, 25A ITU K.20/21/45 - 230Vac, 10 TR600 TR600-150 TR600-160 Telcordia GR-1089 - Level 1 and 2 (***) FCC Part 68 - Type A and B Telcordia GR-1089 - 600Vac, 60A UL 1950, 3rd Ed. - 600Vac, 40A TSU600 TSU600-180 FCC Part 68 - Type A and B ITU K.20/21/45 - 1.5kV 10/700s ITU K.20/21/45 - 4.0kV 10/700s (**) UL 1950, 3rd Ed. - 600Vac, 7A ITU K.20/21/45 - 230Vac, 10 TS600 TS600-170 TS600-200-RA Telcordia GR-1089 - Level 1 and 2 (***) FCC Part 68 - Type A and B Telcordia GR-1089 - 600Vac, 60A UL 1950, 3rd Ed. - 600Vac, 40A (*) Applies to all products which share the same prefix. (**) Tested with 230V gas discharge tube primary protector. (***) Recommend 10 Ohm series resistor for Test 3 (1kV, 10/1000s). Once a device is selected, suitability of the device in the specific application should be evaluated independently. Referenced specifications are a sample list only. For detailed applications information, refer to the Application Notes section of the Raychem Circuit Protection Databook. Voltage Rating for Telecom Devices For Raychem Circuit protection telecom devices (TC, TGC, TRx, TSx) there are two applicable voltage ratings. These are Vmax Operating and Vmax Interrupt. To help understand the nature of these two different voltage ratings the following definitions are provided: Vmax Interrupt: Under specified conditions this is the highest voltage that can be applied to the device at the max current. Devices have been designed to trip safely under higher power level cross conditions, as listed above, to assist equipment in meeting the appropriate industry conditions. Vmax Operating: For telecom devices this is the voltage we have used to obtain component recognition under UL1434. Raychem Circuit Protection devices (TC, TGC, TRx, TSx) are certified at 60V but can withstand higher Vmax Interrupt conditions as noted above. For the purposes of this brochure we have included in the table of electrical ratings the more applicable Vmax Interrupt value. WARNING: TR devices are not intended for continuous utility line voltage such as 120/220 V or 240 V. 3 Thermal derating [Hold current (A) at ambient temperature (C)] Figure T1 : Thermal Derating Curve (Normalized) A = TR250-180U B = All other "T" devices For thermal derating of all non "T" parts see the appropriate section of BBR and RXE (radial leaded products), SMD and miniSMDC (surface mount products) of the Raychem Circuit Protection Databook. Chip1 60/250V Leaded1 60/250V Surface2 80/250V NEW Surface1 60/250V NEW Leaded3 60/600V Surface4 60/600V NEW Surface3 60/600V NEW NEW Leaded 90 V NEW NEW Leaded 60-72V Surface 60 V NEW Surface 60 V Maximum Ambient Temperature Part Number TC250 TGC250 TGC250-120T TGC250-145T TC250-180* -40C Amps -20C 0C 20C 40C 50C 60C 70C 85C 0.186 0.225 0.269 0.165 0.199 0.240 0.143 0.172 0.211 0.120 0.145 0.180 0.099 0.119 0.153 0.088 0.106 0.138 0.077 0.093 0.123 0.066 0.080 0.109 0.050 0.060 0.087 TR250 TR250-080 TR250-110U TR250-120 TR250-145 TR250-180U* 0.124 0.171 0.186 0.225 0.269 0.110 0.151 0.165 0.199 0.240 0.095 0.131 0.143 0.172 0.211 0.080 0.110 0.120 0.145 0.180 0.066 0.091 0.099 0.119 0.153 0.059 0.081 0.088 0.106 0.138 0.051 0.071 0.077 0.093 0.123 0.044 0.061 0.060 0.080 0.109 0.033 0.046 0.050 0.060 0.087 TSL250 TSL250-080 0.124 0.110 0.095 0.080 0.066 0.059 0.051 0.044 0.033 TS250 TSV250 TS250-130 TSV250-130 0.208 0.208 0.182 0.182 0.156 0.156 0.130 0.130 0.104 0.104 0.091 0.091 0.078 0.078 0.065 0.065 0.045 0.045 TR600 TR600-150 TR600-160 0.233 0.249 0.206 0.219 0.178 0.190 0.150 0.160 0.124 0.132 0.110 0.117 0.096 0.103 0.083 0.088 0.062 0.066 TSU600 TSU600-180* 0.270 0.240 0.210 0.180 0.150 0.140 0.120 0.100 0.080 TS600 TS600-170 TS600-200-RA 0.230 0.310 0.218 0.275 0.178 0.238 0.150 0.200 0.124 0.165 0.110 0.147 0.096 0.128 0.090 0.110 0.062 0.083 BBR BBR550* BBR750* 0.850 1.150 0.750 1.000 0.650 0.900 0.550 0.750 0.450 0.610 0.400 0.550 0.350 0.480 0.300 0.410 0.220 0.300 RXE RXE010* RXE017* RXE020* RXE025* RXE030* 0.160 0.260 0.310 0.390 0.470 0.140 0.230 0.270 0.340 0.410 0.110 0.210 0.240 0.300 0.360 0.100 0.170 0.200 0.250 0.300 0.080 0.140 0.160 0.200 0.240 0.072 0.120 0.140 0.180 0.220 0.067 0.110 0.130 0.160 0.190 0.050 0.090 0.110 0.140 0.160 0.040 0.070 0.080 0.100 0.120 SMD SMD030* SMD030-2018* 0.420 0.480 0.380 0.420 0.320 0.350 0.300 0.300 0.240 0.230 0.220 0.200 0.190 0.170 0.170 0.140 0.140 0.010 miniSMD miniSMDC014* 0.230 0.190 0.170 0.140 0.120 0.100 0.090 0.080 0.060 Note 1 - 60/250V products are designed to help equipment pass ITU specifications (K20, K21, etc) and Telcordia Intrabuilding power cross Note 2 - 80/250V products are designed to help equipment pass Telcordia GR-1089 Intrabuilding power cross (120AC/25A) Note 3 - 60/600V products are designed to help equipment pass UL1950, FCC Part 68 and GR-1089 specifications Note 4 - 60/600V products are designed to help equipment pass UL1950 7A max *Product is not available in a resistance binned or sorted option. 4 Product electrical characteristics Chip1 60/250V Leaded1 60/250V Surface2 80/250 NEW Surface1 60/250 NEW Leaded3 60/600 Surface4 60/600 NEW Surface3 60/600 NEW NEW Leaded 90 V NEW NEW Leaded 60-72V Surface6 60 V NEW Surface6 60 V IH (A) IT (A) Vmax Interrupt Imax (A) Pd Typ (W) Typ. Time to Trip (*Max.) (A) (s) RMIN RMAX Part Number TC250 TGC250 TGC250-120T TGC250-145T TC250-180 0.120 0.145 0.180 0.240 0.290 0.360 250 250 250 TR250 TR250-080T TR250-080U TR250-110U TR250-120 TR250-120T TR250-120T-RA TR250-120T-RC TR250-120T-RF TR250-120T-R1 TR250-120T-R2 TR250-120U TR250-120UT TR250-145 TR250-145-RA TR250-145-RB TR250-145T TR250-145U TR250-180U 0.080 0.080 0.110 0.120 0.120 0.120 0.130 0.120 0.120 0.120 0.120 0.120 0.145 0.145 0.145 0.145 0.145 0.180 0.160 0.160 0.220 0.240 0.240 0.240 0.260 0.240 0.240 0.240 0.240 0.240 0.290 0.290 0.290 0.290 0.290 0.360 TSL250 TSL250-080 0.080 TS250 TSV250 TS250-130 TS250-130-RA TS250-130-RB TS250-130-RC TSV250-130 3.0 3.0 3.0 1.00 1.00 1.00 1.00 1.00 1.00 *1.20 1.50 12.00 8.00 6.00 0.80 13.00 10.00 2.00 18.00 14.00 4.00 3 3 3 250 250 250 250 250 250 250 250 250 250 250 250 250 250 250 250 250 250 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 3.0 10.0 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 0.35 0.35 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 *3.00 *3.00 0.75 1.50 0.90 0.90 *3.00 0.90 1.00 0.75 1.00 0.90 2.50 2.50 2.50 2.00 2.00 12.00 15.00 14.00 5.00 4.00 7.00 7.00 5.40 6.00 6.00 8.00 6.00 7.00 3.00 3.00 4.50 5.40 3.50 0.80 22.00 20.00 9.00 8.00 12.00 9.00 7.50 10.50 9.00 10.50 10.00 12.00 6.00 5.50 6.00 7.50 6.50 2.00 33.00 33.00 16.00 16.00 16.00 16.00 14.00 16.00 16.00 16.00 16.00 16.00 14.00 12.00 14.00 14.00 12.00 4.00 1 1 1 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 0.160 250 3.0 1.00 1.00 0.80 5.00 11.00 20.00 8 0.130 0.130 0.130 0.130 0.130 0.260 0.260 0.260 0.260 0.260 250/(650) 250/(650) 250/(650) 250/(650) 250 3.0/(1.1) 3.0/(1.1) 3.0/(1.1) 3.0/(1.1) 3.0 3.00 3.00 3.00 3.00 3.00 1.00 1.00 1.00 1.00 1.00 *2.50 *2.50 *2.50 *2.50 2.00 6.50 6.50 9.00 7.00 4.00 12.00 9.00 12.00 10.00 7.00 20.00 20.00 20.00 20.00 12.00 5 5 5 5 6 TR600 TR600-150 TR600-150-RA TR600-150-RB TR600-160 TR600-160-RA TR600-160-R1 0.150 0.150 0.150 0.160 0.160 0.160 0.300 0.300 0.300 0.320 0.320 0.320 600 600 600 600 600 600 3.0 3.0 3.0 3.0 3.0 3.0 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 1.00 5.00 5.00 5.00 7.00 7.00 7.00 6.00 7.00 9.00 4.00 4.00 4.00 12.00 10.00 12.00 10.00 7.00 8.00 22.00 20.00 22.00 18.00 16.00 17.00 2 2 2 2 2 2 TSU600 TSU600-180(5) 0.180 0.360 600 3.0 3.00 1.00 6.00 3.00 6.00 12.00 9 TS600 TS600-170 TS600-200-RA 0.170 0.200 0.340 0.400 600 600 3.0 3.0 2.50 2.50 1.00 1.00 12.00 12.00 4.00 4.00 9.00 7.50 18.00 13.50 10 10 BBR BBR550(5) BBR750(5) 0.550 0.750 1.100 1.500 (6)90 20.0 20.0 2.00 2.50 1.60 2.00 *60 *60 0.45 0.37 0.90 0.75 2.00 1.65 1 1 RXE RXE010(5) RXE017(5) RXE020(5) RXE025(5) RXE030(5) 0.100 0.170 0.200 0.250 0.300 0.200 0.340 0.400 0.500 0.600 (6)60 40.0 40.0 40.0 40.0 40.0 0.38 0.48 0.41 0.45 0.49 0.50 0.85 1.00 1.25 1.50 4.00 3.00 2.20 2.50 3.00 2.50 3.30 1.83 1.25 0.88 4.50 5.21 2.75 1.95 1.33 7.50 8.00 4.40 3.00 2.10 1 1 1 1 1 SMD SMD030(5) SMD030-2018(5) 0.300 0.300 0.600 0.800 (6)60 (6)60 10.0 20.0 1.70 0.70 1.50 1.50 3.00 *1.50 1.20 0.50 3.00 1.40 4.80 2.30 8 7 miniSMD miniSMDC014(5) 0.140 0.340 (6)60 10.0 0.60 1.50 0.15 1.50 5.00 6.00 4 (6)90 (6)60 (6)72 (6)72 (6)72 Note 1- 60/250V products are designed to help equipment pass ITU specifications (K20, K21, etc) and Telcordia Intrabuilding power cross Note 2- 80/250V products are designed to help equipment pass Telcordia GR-1089 Intrabuilding power cross (120AC/25A) Note 3- 60/600V products are designed to help equipment pass UL1950, FCC Part 68 and GR-1089 specifications Note 4- 60/600V products are designed to help equipment pass UL1950 7A max Note 5- Product is not available in a resistance binned or sorted option Note 6- Voltage rating for these products is Vmax operating 5 IH R1MAX Figures for Dims. = Hold current - maximum current device will pass without interruption in 20C still air IT = Trip current - minimum current that will switch the device from low resistance to high resistance in 20C still air Vmax Interrupt = Maximum voltage that can be safely placed across a device in its tripped state under specified fault conditions Imax = Maximum fault current device can withstand without damage at rated voltage Pd = Power dissipated from device when in the tripped state in 20C still air R1max = Maximum device resistance, measured one-hour post trip Physical description for dimensions A A Marking Marking B 0.65mm 0.65mm E (center to center) E (center to center) C C B B D D Figure 2 Figure 1 A A C B C B D E Figure 4 Figure 3 A T13 C C B E Top view D End view F B E D A Side view End view Figure 5 Figure 6 C C B B E D D D D A A Figure 8 Figure 7 A C C F B A B D E A Figure 9 D Figure 10 6 Product dimensions (millimeters/inches) Dim A Min Dim A Max Dim B Min Dim B Max Dim C Min Dim C Max 5.5 (0.216) 5.5 (0.216) 5.9 (0.232) 5.9 (0.232) 10.4 (0.410) 5.5 (0.216) 5.5 (0.216) 5.9 (0.232) 5.9 (0.232) 6.6 (0.260) 2.0 (0.080) 2.0 (0.080) 2.3 (0.090) 2.3 (0.090) 2.54 (0.100) Dim D Min Dim D Max Dim E Min Dim E Max Dim F Min Dim F Max Figure Part Number TC/TGC 60/250V1 TGC250-120T TGC250-145T TC250-180 3 3 3 TR250 60/250V1 5.3 (0.209) 4.8 (0.189) 5.3 (0.210) 6.5 (0.256) 6.0 (0.236) 6.5 (0.256) 6.0 (0.236) 10.4 (0.410) TR250-080T TR250-080U TR250-110U TR250-120 TR250-120U TR250-145 TR250-145U TR250-180U 9.9 (0.390) 9.3 (0.366) 9.4 (0.370) 11.0 (0.433) 10.0 (0.394) 11.0 (0.433) 10.0 (0.394) 12.6 (0.495) 3.8 (0.150) 3.8 (0.150) 3.8 (0.15) 4.6 (0.180) 3.8 (0.150) 4.6 (0.180) 3.8 (0.150) 3.6 (0.140) 4.7 (0.185) 4.7 (0.185) 4.7 (0.185) 4.7 (0.185) 4.7 (0.185) 4.7 (0.185) 4.7 (0.185) 4.7 (0.185) 5.4 (0.210) 0.2 (0.008) *5.0 (0.197) *5.0 (0.197) *5.0 (0.197) *5.0 (0.197) *5.0 (0.197) *5.0 (0.197) *5.0 (0.197) *5.0 (0.197) 1 1 1 2 2 2 2 2 TSL250 80/250V2 TSL250-080 TS250/TSV250 6.7 (0.265) 7.9 (0.310) 2.7 (0.110) 3.7 (0.145) 4.8 (0.190) 0.3 (0.012) 2.5 (0.100) 8.5 (0.335) 9.4 (0.370) 6.1 (0.240) 3.4 (0.135) 6.9 (0.270) 7.4 (0.290) 3.2 (0.126) *0.3 (0.011) 0.56 (0.022) *3.8 (0.150) 13.5 (0.531) 16.0 (0.630) 12.6 (0.496) 12.6 (0.496) 6.0 (0.236) 6.0 (0.236) 4.7 (0.185) 4.7 (0.185) *5.0 (0.197) *5.0 (0.197) 3.1 (0.120) 8 60/250V1 TS250-130 TSV250-130 5 1.9 (0.075) 1.6 (0.065) 2.3 (0.091) 6 TR600 60/600V3 TR600-150 TR600-160 2 2 TSU600 60/600V4 TSU600-180 TS600 11.4 (0.450) 12.2 (0.480) 1.7 (0.070) 2.1 (0.084) 8.5 (0.335) 9.3 (0.365) 0.5 (0.02) 1.0 (0.04) 18.2 (0.720) 18.2 (0.720) 19.4 (0.765) 19.4 (0.765) 11.5 (0.452) 11.5 (0.452) 12.3 (0.485) 12.3 (0.485) 7.6 (0.300) 7.6 (0.300) 8.4 (0.330) 8.4 (0.330) 1.6 (0.065) 1.6 (0.065) 2.4 (0.095) 2.4 (0.095) 9 60/600V3 TS600-170 TS600-200-RA 9.9 (0.390) 9.9 (0.390) 10.4 (0.410) 10.4 (0.410) 1.5 (0.060) 1.5 (0.060) 2.3 (0.090) 2.3 (0.090) 10 10 BBR 90 V 10.9 (0.43) 11.9 (0.47) 14.0 (0.55) 15.5 (0.61) 3.6 (0.14) 3.6 (0.14) 7.6 (0.30) 7.6 (0.30) 4.3 (0.17) 4.3 (0.17) 5.8 (0.23) 5.8 (0.23) 7.4 (0.29) 7.4 (0.29) 7.4 (0.29) 7.4 (0.29) 7.4 (0.29) 12.7 (0.50) 12.7 (0.50) 12.2 (0.48) 12.7 (0.50) 13.0 (0.51) 3.0 (0.12) 3.0 (0.12) 3.0 (0.12) 3.0 (0.12) 3.0 (0.12) 7.6 (0.30) 7.6 (0.30) 7.6 (0.30) 7.6 (0.30) 7.6 (0.30) 4.3 (0.17) 4.3 (0.17) 4.3 (0.17) 4.3 (0.17) 4.3 (0.17) 5.8 (0.23) 5.8 (0.23) 5.8 (0.23) 5.8 (0.23) 5.8 (0.23) 6.73 (0.265) 4.72 (0.186) 7.98 (0.314) 5.44 (0.214) 3.18 (0.125) 1.78 (0.070) 0.56 (0.022) 0.25 (0.010) 2.16 (0.085) 2.41 (0.095) 4.22 (0.166) 5.44 (0.214) 4.93 (0.194) 4.37 (0.172) 4.73 (0.186) 0.63 (0.025) 0.89 (0.035) 3.07 (0.121) 3.41 (0.134) 0.30 (0.012) *Indicates dimensional is typical, not minimum. Note 1 - 60/250V products are designed to help Note 2 - 80/250V products are designed to help Note 3 - 60/600V products are designed to help Note 4 - 60/600V products are designed to help equipment equipment equipment equipment BBR550 BBR750 1 1 RXE 60-72V RXE010 RXE017 RXE020 RXE025 RXE030 1 1 1 1 1 SMD 60V SMD030 SMD030-2018 0.71 (0.028) 0.36 (0.014) 8 7 miniSMD 60V miniSMDC014 0.25 (0.010) 0.50 (0.020) pass ITU specifications (K20, K21, etc) and Telcordia Intrabuilding power cross pass Telcordia GR-1089 Intrabuilding power cross (120AC/25A) pass UL1950, FCC Part 68 and GR-1089 specifications pass UL1950 7A max 7 4 Time-to-trip at 20C TC250 A -- TGC250-120T B -- TGC250-145T C - TC250-180U TR250 A - TR250-080T/080U B - TR250-110U/120UT/120T C - TR250-120/120U D - TR250-145/145U E - TR250-180U TS250/TSV250 A - TSL250-080 B - TSV250-130 C - TS250-130 TR600/TS600/TSU600 A - TR600-150 B - TSU600-180 C - TR600-160 D - TS600-170/200 8 Time-to-trip at 20C RXE - Typical Time-to-Trip RXE A - RXE010 A 1000 BC DE B - RXE017 C - RXE020 100 D - RXE025 E - RXE030 Time-to-trip (s) 10 1 0.1 0.01 0.001 0.1 1 10 100 Fault current (A) SMD/miniSMDC SMD/miniSMDC - Typical Time-to-Trip 100 B - SMD030-2018 10 C - SMD030 Time-to-trip (s) A - miniSMDC014 A B C 1 0.1 0.01 0.001 0.1 9 1 Fault current (A) 10 Physical characteristics and environmental specifications (Operating temperature range for all listed products is -40C to 85C) TC2501/TGC2501 Physical characteristics Lead material Environmental specifications Test Passive aging Nickel foil or tin/lead plated nickel foil Humidity aging Thermal Shock Solvent Resistance Conditions 60C, 1000 hours 85C, 1000 hours 85C, 85% RH, 1000 hours 125C, -55C (10 times) MIL-STD-202, Method 215F TR2501 Physical characteristics Lead material Insulating material Flammability Soldering characteristics Solder heat withstand Tin/lead plated copper, 22 AWG, 0.65mm (0.026 in) Cured epoxy polymer per IEC 695-2-2 Needle flame test for 20 sec. ANSI/J-STD-002, Category 3 IEC-STD 68-2-20, Test Tb, Section 5 Method 1A Environmental specifications Test Passive aging Humidity aging Thermal Shock Solvent Resistance Conditions 60C, 1000 hours 85C, 1000 hours 85C, 85% RH, 1000 hours 125C, -55C (10 times) MIL-STD-202, Method 215F TS2501/TSV2501/TSL2502 Physical characteristics Lead material Soldering characteristics Tin plated brass ANSI/J-STD-002, Category 3 Environmental specifications Test Passive aging Humidity aging Thermal shock Solvent resistance Conditions 60C, 1000 hours 85C, 1000 hours 85C, 85% RH, 500 hours 125C, -55C (10 times) MIL-STD-202, Method 215F TR6003 Physical characteristics Lead material Insulating material Flammability Soldering characteristics Solder heat withstand Tin/lead plated copper, 22 AWG, 0.65mm (0.026 in) Cured epoxy polymer per IEC 695-2-2 Needle flame test for 20 sec. ANSI/J-STD-002, Category 3 IEC-STD 68-2-20, Test Tb, Section 5 Method 1A Environmental specifications Test Passive aging Humidity aging Thermal shock Solvent resistance Conditions 60C, 1000 hours 85C, 1000 hours 85C, 85% RH, 1000 hours 125C, -55C (10 times) MIL-STD-202, Method 215F 10 Physical characteristics and environmental specifications TS6003 Physical characteristics Lead material Insulating material Flammability Soldering characteristics Solder heat withstand Environmental specifications Test Passive aging Tin-plated brass Nylon resin (UL94V-0), 1000V dielectric rating IEC 695-2-2 Needle flame test for 20 sec. ANSI/J-STD-002, Category 3 IEC-STD 68-2-20, Test Tb, Section 5 Method 1A Humidity aging Thermal shock Solvent resistance Conditions 60C, 1000 hours 85C, 1000 hours 85C, 85% RH, 1000 hours 125C, -55C (10 times) MIL-STD-202, Method 215F TSU6004 Physical characteristics Lead material Soldering characteristics Solder heat withstand Tin plated brass and nickel foil ANSI/J-STD-002, Category 3 IEC-STD 68-2-20, Test Tb, Section 5 Method 1A Environmental specifications Test Passive aging Humidity aging Thermal shock Solvent resistance Conditions 60C, 1000 hours 85C, 1000 hours 85C, 85% RH, 1000 hours 125C, -55C (10 times) MIL-STD-202, Method 215F BBR Physical characteristics Lead material Insulating material Flammability Soldering characteristics Solder heat withstand Tin/lead plated copper, 20 AWG, 0.81mm (0.032 in) Cured, flame-retardant epoxy polymer; meets UL 94V-0 requirements per IEC 695-2-2 Needle flame test for 20 sec. ANSI/J-STD-002, Category 3 IEC-STD 68-2-20, Test Tb, Section 5 Method 1A Environmental specifications Test Passive aging Humidity aging Thermal Shock Solvent Resistance Note Note Note Note Note 12345- Conditions 60C, 1000 hours 85C, 1000 hours 85C, 85% RH, 1000 hours 125C, -55C (10 times) MIL-STD-202, Method 215F 60/250V products are designed to help equipment pass ITU specifications (K20, K21, etc) and Telcordia Intrabuilding power cross 80/250V products are designed to help equipment pass Telcordia GR-1089 Intrabuilding power cross (120AC/25A) 60/600V products are designed to help equipment pass UL1950, FCC Part 68 and GR-1089 specifications 60/600V products are designed to help equipment pass UL1950 7A max Product is not available in a resistance binned or sorted option For physical and environmental characteristics of RXE, SMD, and miniSMD, products see the Raychem Circuit Protection Databook. 11 Recommended pad layouts The dimensions in the table below provide the recommended pad layout for each surface mount device. Pad dimensions in millimeters (inches). Device TS250 (all) TSV250-130 TSL250-080 TS600 (all) TSU600-180 SMD030-2018 SMD030 miniSMDC014 A nom 4.6 (0.18) 2.29 (0.09) 3.6 (0.14) 9.91 (0.390) 9.4 (0.37) 4.6 (0.18) 3.1 (0.12) 3.15 (0.124) B nom 1.8 (0.07) 2.41 (0.095) 1.8 (0.07) 3.30 (0.130) 8.9 (0.35) 1.5 (0.06) 2.3 (0.09) 1.78 (0.07) *C nom 6.1 (0.24) 6.35 (0.25) 5.5 (0.22) 3.35 (0.132) 1.78 (0.07) 3.4 (0.13) 5.1 (0.20) *3.45 (0.136) D nom E nom F nom Figure Pad Layout Figure 1 1 3.43 (0.135) A 2 1 B C B 1 1.27 (0.05) 5.6 (0.22) 1.9 (0.075) 3 Pad Layout Figure 2 1 1 1 A A D B *Indicates minimum dimension. For TS, SMD and miniSMD devices only (Radial leaded devices [TR250, TR600, RXE, BBR] are not designed to be placed in a reflow process). B C Pad Layout Figure 3 D B C E A F Solder reflow and rework recommendations for surface mount devices Temperature (C) 300 Preheating Soldering Solder Reflow * Recommended reflow methods: IR, vapor phase oven, hot air oven. * Devices are not designed to be wave soldered to the bottom side of the board. * Gluing of the devices is not recommended. * Recommended maximum paste thickness of 0.25mm (0.010 in). * Devices can be cleaned using standard industry methods and solvents. Cooling 250 200 150 100 Rework * If a device is removed from the board, it should be discarded and a new device used as a replacement. 50 0 30-90 sec. 5 sec. 120 sec. Time Caution * If reflow temperatures exceed recommended profile, devices may not meet the performance requirements. * Leaded devices are not designed to be compatible with reflow manufacturing operations. * Recommended solder/temperature exposure for leaded devices is designated in the environmental/physical tables for the product family. Exposure to temperatures or duration at temperature in excess of these values may lead to device not meeting performance requirements. 12 Packaging and marking information Bag Quantity Chip1 60/250 Leaded1 60/250V Surface2 80/250V Surface1 60/250V Leaded3 60/600V Surface4 60/600V Surface3 60/600V Radial 90V Radial 60-72V Surface 60V Surface 60V Part Number TC250 TGC250 TGC250-120T TGC250-145T TC250-180 Tape & Reel Quantity Part Marking Agency Recognition 25,000 25,000 10,000 x x 1,500 10,000 7,500 10,000 10,000 7,500 10,000 7,500 10,000 7,500 10,000 7,500 10,000 10,000 7,500 10,000 10,000 7,500 10,000 7,500 x08 x08 x08 x10 x10 x20 x20 x20 x20 x20 x20 x20 x45 x45 x45 x45 x45 x80 x80 TSL250 TSL250-080-2 1,500 7,500 xT08 UL Pending TS250 TSV250 TS250-130-2 TSV250-130-2 1,500 1,300 7,500 6,500 xT13 xT13V UL, CSA, TUV UL Pending 600 10,000 3,000 10,000 3,000 x150 x150 x160 x160 TS6U00 TSU600-180-2 900 4,500 xT18U UL TS600 TS600-170-2 TS600-200-RA-2 300 300 900 900 xT20 xT20 UL, CSA UL, CSA UL UL Pending TR250 TR250-080U TR250-080U-2 TR250-080T TR250-110U TR250-110U-2 TR250-120 TR250-120-2 TR250-120T TR250-120T-2 TR250-120U TR250-120U-2 TR250-120UT TR250-145 TR250-145-2 TR250-145-RA TR250-145U TR250-145U-2 TR250-180U TR250-180U-2 TR600 TR600-150 TR600-150-2 TR600-160 TR600-160-2 5,000 5,000 2,500 Standard Package 500 1,500 500 500 1,500 500 1,500 500 1,500 500 1,500 500 500 1,500 500 500 1,500 500 500 600 500 UL, UL, UL, UL, UL, UL, UL, UL, UL, UL, UL, UL, UL, UL, UL, UL, UL, UL, UL, CSA, TUV CSA, TUV CSA, TUV CSA, TUV CSA, TUV CSA, TUV CSA, TUV CSA, TUV CSA, TUV CSA, TUV CSA, TUV CSA, TUV CSA, TUV CSA, TUV CSA, TUV CSA, TUV CSA, TUV CSA, TUV CSA, TUV UL, UL, UL, UL, BBR BBR550 BBR750 500 500 10,000 10,000 B550 B750 RXE RXE010 RXE017 RXE020 RXE025 RXE030 500 500 500 500 500 10,000 10,000 10,000 10,000 10,000 x010 x017 x020 x025 x030 UL, UL, UL, UL, UL, CSA CSA CSA CSA CSA, TUV CSA, TUV CSA, TUV CSA, TUV CSA, TUV SMD SMD030-2 SMD030-2018-2 2,000 4,000 10,000 20,000 x030 A03 UL, CSA, TUV UL miniSMD miniSMDC014-2 4,000 20,000 14 UL, CSA, TUV *Bold indicates minimum specified dimension Note 1 - 60/250V products are designed to help equipment pass ITU specifications (K20, K21, etc) and Telcordia Intrabuilding power cross Note 2 - 80/250V products are designed to help equipment pass Telcordia GR-1089 Intrabuilding power cross (120AC/25A) Note 3 - 60/600V products are designed to help equipment pass UL1950, FCC Part 68 and GR-1089 specifications Note 4 - 60/600V products are designed to help equipment pass UL1950 7A max Note 5 - Product is not available in a resistance binned or sorted option 13 Agency recognition UL File # E74889 CSA File #78165C TUV Certificate #R9872248.1 Part numbering TR250 -145 US -RA -B-0.5 -2 2 = Tape and reel packaging Bxx = Binning (Optional) Rx = Resistance range (Optional) Modifier (Optional) U = Uncoated chip S = Straight lead T = Pre-tripped device Hold current (mA) Product family (Indicates maximum interrupt voltage rating 250V or 600V) SMD 030 /30 -2 2 = Tape and reel packaging Alternative voltage rating (if applicable) Current rating Product family Resistance sorted and binned TC, TGC, TR, and TS devices are available in resistance sorted and resistance binned. Resistance sorted devices Resistance sorted devices (part number suffix "Rx", where x=1, 2, A, B, C, F etc.) are supplied with resistance values that are within specified limits of the product's full range of resistance. Feature * Tighter resistance limits. Benefits * Tighter resistance ranges offer greater flexibility for design engineers. Lower resistance range devices allow designers a tighter resistance budget which can allow for increased loop length on line card designs. Higher resistance range parts may allow the designer to adjust line balance while still meeting total resistance requirements. Resistance binned devices Resistance binned devices are supplied such that all parts in one particular package (or reel) are within 0.5 of each other (1.0 for 080T devices). Individual binned packages are supplied from the full resistance limits of the specified product. Feature * Tighter resistance balance between any two parts in a package. Benefit * Resistance binned devices provide tighter tolerance parts on a tip-ring line pair. This reduces the tip-ring resistance differential, limiting the possibility of line imbalance. 14 TR250/TR600 Tape and Reel specifications (dimensions in millimeters) TR250/TR600 devices are available tape and reeled per EIA 468-B standard. See Figures 1 and 2 for details. Dimensions Dimension Description EIA mark W W4 W6 W5 D0 H H0 H1 Carrier tape width Hold down tape width Top distance between tape edges Sprocket hole position Sprocket hole diameter Abcissa to plane (straight lead)* Abcissa to plane (kinked lead)* Abcissa to top Overall width w/lead protrusion Overall width w/o lead protrusion Lead protrusion Protrusion of cut-out Protrusion beyond hold down tape Sprocket hole pitch Device pitch: TR250 Device pitch: TR600 Pitch tolerance Tape thickness Tape thickness with splice* Splice sprocket hole alignment Body lateral deviation Body tape plane deviation Lead spacing plane deviation Lead seating Reel width Reel diameter Space between flanges less device Arbor hole diameter Core diameter Box Consecutive missing pieces* Empty places per reel* *Differs from EIA Specification. IEC mark W W0 W2 W1 D0 H H0 H1 C1 C2 I1 L I2 P0 L1 L I2 P0 t t1 t h p P1 F w2 a w1 c n h p P1 F w d f h Dimensions (mm) Dimensions (mm) 18 5 3 9 4 18.5 16 32.2 43.2 42.5 1.0 11 Not specified 12.7 12.7 25.4 20 consecutive 0.9 2.0 0 0 0 0 5.08 56 370 4.75 26 80 56/372/372 3 maximum Not specified -0.5/+1.0 min. max. -0.5/+0.75 0.2 3.0 -0.5/+0.6 max. max. max. max. max. 0.3 1 max. max. 0.3 1.0 1.3 0.7 -0.5/+0.6 max. max. 3.25 12.0 max. max. Figure 1: EIA referenced taped component dimensions for TR devices h h p p Reference plane P1 H1 H1 C1 H C2 F A L H0 B W4 W5 W I2 L1 D0 P0 Direction of unreeling Cross section A - B t1 t Figure 2: Reel dimensions for TR devices Reel Upper side n Tape a Direction of unreeling Lower side c w1 w2 Cross section Optional shape: Circular or polygonal 15 TS Tape and reel specifications (dimensions in millimeters) TS devices are packaged per EIA 481 and EIA 481-2 standards. See Figures 3 and 4 for details TS250/TSL250/TSV250 TS250 Dimension Description Carrier Tape width Sprocket hole pitch Sprocket hole diameter Tape thickness Cover tape thickness Reel Dimensions Reel diameter Core diameter Space between flanges less device Reel width EIA Dimension mark (mm) W 16 P0 4.0 P1 12.0 P2 2.0 A0 7.7 B0 9.6 B1 max. 12.1 D0 1.5 F 7.5 E1 1.75 E2 min. 14.25 Tmax. 0.4 T1 max. 0.1 K0 3.4 Leader min. 390 Trailer min. 160 A max. N min. W1 W2 max. 340 50 16.4 22.4 TSV250 TSL250 Tolerance (mm) 0.3 0.10 0.10 0.10 0.23 0.15 Dimension (mm) 16 4.0 8.0 2.0 5.5 6.2 Tolerance (mm) 0.3 0.1 0.1 0.1 0.1 0.1 Dimension (mm) 16 4.0 8.0 2.0 5.5 7.9 Tolerance (mm) 0.3 0.10 0.10 0.10 0.10 0.10 -0/+0.1 0.10 0.10 1.5 7.5 1.75 -0/+0.1 0.10 0.10 1.5 7.5 1.75 -0/+0.1 0.10 0.10 0.15 0.45 0.1 7.00 390 160 0.1 0.4 0.1 3.70 390 160 0.10 340 50 16.4 22.4 -0/+2.0 340 50 16.4 22.4 -0/+2.0 -0/+2.0 TS600/TSU600 TS600 Dimension Description Carrier Tape width Sprocket hole pitch Sprocket hole diameter Tape thickness Tape thickness with splice Reel Dimensions Reel diameter Core diameter Space between flanges less device Reel width EIA mark W P0 P1 P2 A0 B0 B1 max. D0 F E1 E2 min. Tmax. T1 max. K0 Leader min. Trailer min. A max. N min. W1 W2 max. Dimension (mm) 32 4.0 16 2.0 10 19.2 12.1 1.5 14.2 1.75 28.4 0.50 0.1 13.2 390 160 360 50 32.4 40 TSU600 Tolerance (mm) 0.3 0.1 0.1 0.1 0.1 0.1 Dimension (mm) 24 4.0 12.0 2.0 9.3 9.3 Tolerance (mm) 0.3 0.1 0.1 0.1 0.1 0.1 -0/+0.1 0.1 0.1 0.1 0.5 1.5 11.5 1.75 -0/+0.1 0.1 0.1 0.30 0.1 2.4 390 160 0.1 0.1 -0/+2.0 360 50 24.4 30.4 Refer to applicable sections for tape and reel information on BBR and RXE (radial leaded products) and miniSMDC and SMD (surface mount products). See the Raychem Circuit Protection Databook. 16 0.1 -0/+2.0 TS Tape and reel specifications (cont.) Figure 3: EIA referenced taped component dimensions for TS devices P0 D0 T Embossment P2 E1 Cover tape A0 W F E2 B1 B0 K0 T1 P1 Center lines of cavity Figure 4: Reel dimensions for TS devices W2 (measured at hub) A Cover tape N (hub dia.) W1 (measured at hub) Carrier tape Embossed cavity Latest Information * Please check the Raychem Circuit Protection web site (www.circuitprotection.com) or contact your local representative for the latest information. * The information in this data package contains some preliminary information. Raychem Circuit Protection reserves the right to change any of the specifications without notice. In addition, Raychem Circuit Protection reserves the right to make changes--without notification to Buyer--to materials or processing that do not affect compliance with any applicable specification. WARNING * Operation beyond the maximum ratings or improper use may result in device damage and possible electrical arcing and flame. * These devices are intended for protection against occasional overcurrent or overtemperature fault conditions, and should not be used when repeated fault conditions are anticipated. 17 Worldwide Headquarters 308 Constitution Drive Menlo Park, CA 94025-1164 Tel (800) 227-7040 (650) 361-6900 Fax (650) 361-2508 www.circuitprotection.com www.raychem.com/go/jpn/polyswitch (Japanese) South America Europe Asia/Pacific Argentina Tel 54-11-4394-5150 Fax 54-11-4326-9985 UK/EIRE/Nordic Countries Tel 44-1793-572-244 Fax 44-1793-573-178 Australia, Sydney Tel 61-2-9890-3944 Fax 61-2-9890-3977 Japan Tel 81-44-900-5110 Fax 81-44-900-5140 Brazil Tel 55-11-816-0066 Fax 55-11-816-0301 Germany/Austria/ Switzerland/ Eastern Europe Tel 49-89-608-9386 Fax 49-89-608-9394 China, Beijing Tel 86-10-6581-5606 Fax 86-10-6581-5608 Korea Tel 82-2-3415-4650 Fax 82-2-3486-1786 China, Guangzhou Tel 86-20-8330-9933 Fax 86-20-8385-6139 Philippines Tel 63-2-867-8641 Fax 63-2-867-8661 China, Hong Kong Tel 852-2738-3401 Fax 852-2735-1185 Singapore Tel 65-486-6126 Fax 65-484-0661 China, Shanghai Tel 86-21-6485-3288 Fax 86-21-6485-5109 Taiwan Tel 886-2-2662-9788 Fax 886-2-2662-4684 India, Bangalore Tel 91-80-559-1485 Fax 91-80-558-6039 Thailand Tel 66-2-955-0500 Fax 66-2-955-0496 Chile Tel 56-2-209-8211 Fax 56-2-223-1477 Colombia Tel 57-1-218-2460 Fax 57-1-218-2472 Peru Tel 511-221-4165 Fax 551-421-0368 Uruguay Tel 598-982-2428 Fax 598-982-2430 France/Benelux/Italy/Iberia Tel 33-1-3440-7289 Fax 33-1-3440-7288 Other Countries Tel 32-16-351-321 Fax 32-16-351-319 PolySwitch and miniSMD are trademarks of Tyco Electronics Corporation. All information, including illustrations, is believed to be reliable. Users, however, should independently evaluate the suitability of each product for their application. Tyco Electronics makes no warranties as to the accuracy or completeness of the information, and disclaims any liability regarding its use. Tyco Electronics' only obligations are those in the Company's Standard Terms and Conditions of Sale for this product, and in no case will Tyco Electronics be liable for any incidental, indirect, or consequential damages arising from the sale, resale, use, or misuse of the product. Specifications are subject to change without notice. In addition, Tyco Electronics reserves the right to make changes-without notification to Buyer-to materials or processing that do not affect compliance with any applicable specification. 2000 Tyco Electronics Corporation Printed in USA RCP0018.1100.3000 Venezuela Tel 58-2-242-6475 Fax 58-2-241-8260