ILLUMINATION LUXEON Z Industry's smallest high power emitter for use in close-packed applications requiring an undomed solution LUXEON Z is a high power 1.3mm x 1.7mm LED that enables never before seen color consistency, luminance, flux density and design flexibility for lighting solutions. LUXEON Z is undomed, a feature that provides unmatched optical flexibility for precise beam angle control. Tested and binned at application conditions 85C and available in 3- and 5-step MacAdam ellipse color bins. LUXEON Z emitters are an ideal choice for indoor and outdoor light sources requiring superior beam angles, higher efficacy and lower costs. FEATURES AND BENEFITS PRIMARY APPLICATIONS 1.3mm x 1.7mm micro footprint enables a high degree of design flexibility Architectural Undomed design allows precise optical control Downlights 1A max drive current allows for more flux per LED Indoor Area Lighting 3- and 5-step MacAdam ellipse color binning for superior Quality of Light Lamps Outdoor Specialty Lighting Spotlights DS120 LUXEON Z Product Datasheet (c)2017 Lumileds Holding B.V. All rights reserved. No. E352519 Table of Contents General Product Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Product Test Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Part Number Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Lumen Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Environmental Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Performance Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Product Selection Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Optical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Electrical and Thermal Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Characteristic Curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Spectral Power Distribution Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Light Output Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Forward Current Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Radiation Pattern Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Product Bin and Labeling Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Decoding Product Bin Labeling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Luminous Flux Bins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Color Bin Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Forward Voltage Bins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Mechanical Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Reflow Soldering Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 JEDEC Moisture Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Solder Pad Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Packaging Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Pocket Tape Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Reel Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 DS120 LUXEON Z Product Datasheet 20170327 (c)2017 Lumileds Holding B.V. All rights reserved. i General Product Information Product Test Conditions LUXEON Z LEDs are tested and binned with a DC drive current of 500mA at a junction temperature, Tj, of 85C. Part Number Nomenclature Part numbers for LUXEON Z follow the convention below: L X Z 1 - A A B B - C Where: A A - designates nominal ANSI CCT (27=2700K, 30=3000K, 35=3500K, 40=4000K, 50=5000K, 57=5700K, 65=6500K RB=Royal Blue) B B - designates minimum CRI (65=65CRI, 70=70CRI, 80=80CRI) C designates SDCM (3=3 SDCM, 5=5 SDCM). - Therefore, the following part number is used for a LUXEON Z 3000K, 80 CRI, 5 SDCM : L X Z 1 - 3 0 8 0 - 5 Lumen Maintenance Please contact your local Sales Representative or Lumileds Technical Solutions Manager for more information about the longterm performance of this product. Environmental Compliance Lumileds LLC is committed to providing environmentally friendly products to the solid-state lighting market. LUXEON Z is compliant to the European Union directives on the restriction of hazardous substances in electronic equipment, namely the RoHS Directive 2011/65/EU and REACH Regulation (EC) 1907/2006. Lumileds LLC will not intentionally add the following restricted materials to its products: lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls (PBB) or polybrominated diphenyl ethers (PBDE). DS120 LUXEON Z Product Datasheet 20170327 (c)2017 Lumileds Holding B.V. All rights reserved. 2 Performance Characteristics Product Selection Guide Table 1. Product performance of LUXEON Z at 500mA and 700mA, Tj=85C. TYPICAL LUMINOUS EFFICACY (lm/W) TYPICAL LUMINOUS FLUX (lm) 154 110 197 99 LXZ1-6565 120 134 96 172 86 LXZ1-4070 70 130 148 106 189 95 LXZ1-5070 70 140 152 109 195 98 LXZ1-5770 2700K 80 100 115 82 147 74 LXZ1-2780-y 3000K 80 110 124 89 159 80 LXZ1-3080-y 3500K 80 110 124 89 159 80 LXZ1-3580-y 4000K 80 120 130 93 166 83 LXZ1-4080-y LUMINOUS FLUX [1] (lm) NOMINAL CCT MINIMUM CRI [1, 2] MINIMUM 6500K 65 140 4000K 70 5000K 5700K TYPICAL 500mA TYPICAL LUMINOUS EFFICACY (lm/W) PART NUMBER 700mA Notes for Table 1: 1. Lumileds maintains a tolerance of 2 on CRI and 6.5% on luminous flux measurements. 2. Typical CRI is approximately 2 points higher than the minimum CRI specified, but this is not guaranteed. Optical Characteristics Table 2. Optical characteristics for LUXEON Z at 500mA, Tj=85C. PART NUMBER TYPICAL TOTAL INCLUDED ANGLE [1] TYPICAL VIEWING ANGLE [2] LXZ1-xxxx-y 160 120 LXZ1-xxxx 160 120 Notes for Table 2: 1. Total angle at which 90% of total luminous flux is captured. 2. Viewing angle is the off axis angle from the LED centerline where the luminous intensity is 1/2 of the peak value. Electrical and Thermal Characteristics Table 3. Electrical and thermal characteristics for LUXEON Z at 500mA, Tj=85C. FORWARD VOLTAGE [1] (Vf) MINIMUM TYPICAL MAXIMUM TYPICAL TEMPERATURE COEFFICIENT OF FORWARD VOLTAGE (mV/C) [2] LXZ1-xxxx-y 2.5 2.8 3.25 -1.6 6 LXZ1-xxxx 2.5 2.8 3.25 -1.6 6 PART NUMBER TYPICAL THERMAL RESISTANCE -- JUNCTION TO SOLDER PAD (C/W) Notes for Table 3: 1. Lumileds maintains a tolerance of 0.06V on forward voltage measurements. 2. Measured between 25C and 85C. DS120 LUXEON Z Product Datasheet 20170327 (c)2017 Lumileds Holding B.V. All rights reserved. 3 Absolute Maximum Ratings Table 4. Absolute maximum ratings for LUXEON Z. PARAMETER MAXIMUM PERFORMANCE DC Forward Current 1000mA [1, 2] Peak Pulsed Forward Current [1, 3] LED Junction Temperature [1] 1200mA (DC & Pulse) 135C ESD Sensitivity (ANSI/ESDA/JEDEC JS-001-2012) Class 3B Operating Case Temperature [1] -40C to 135C LED Storage Temperature -40C to 135C Soldering Temperature JEDEC 020c 260C Allowable Reflow Cycles 3 Reverse Voltage (Vreverse) LUXEON LEDs are not designed to be driven in reverse bias Notes for Table 4: 1. Proper current derating must be observed to maintain the junction temperature below the maximum allowable junction temperature. 2. Residual periodic variations due to power conversion from alternating current (AC) to direct current (DC), also called "ripple," are acceptable if the following conditions are met: - The frequency of the ripple current is 100Hz or higher - The average current for each cycle does not exceed the maximum allowable DC forward current - The maximum amplitude of the ripple does not exceed the maximum peak pulsed forward current 3. At 10% duty cycle with pulse of 10ms. Characteristic Curves Spectral Power Distribution Characteristics Figure 1a: Typical normalized power vs. wavelength for LXZ1-xx65 at 500mA, Tj=85C. DS120 LUXEON Z Product Datasheet 20170327 (c)2017 Lumileds Holding B.V. All rights reserved. 4 Figure 1b: Typical normalized power vs. wavelength for LXZ1-xx70 at 500mA, Tj=85C. Figure 1c: Typical normalized power vs. wavelength for LXZ1-xx80 at 500mA, Tj=85C. DS120 LUXEON Z Product Datasheet 20170327 (c)2017 Lumileds Holding B.V. All rights reserved. 5 Light Output Characteristics Figure 2: Typical normalized light output vs. junction temperature for LXZ1-xxxx at 500mA. Figure 3: Typical normalized light output vs. forward current for LXZ1-xxxx at Tj=85C. DS120 LUXEON Z Product Datasheet 20170327 (c)2017 Lumileds Holding B.V. All rights reserved. 6 Forward Current Characteristics Figure 4: Typical forward current vs. forward voltage for LXZ1-xxxx at Tj=85C. Radiation Pattern Characteristics Figure 5: Typical radiation pattern for LXZ1-xxxx at 500mA, Tj=85C. DS120 LUXEON Z Product Datasheet 20170327 (c)2017 Lumileds Holding B.V. All rights reserved. 7 Figure 6: Typical polar radiation pattern for LXZ1-xxxx at 500mA, Tj=85C. DS120 LUXEON Z Product Datasheet 20170327 (c)2017 Lumileds Holding B.V. All rights reserved. 8 Product Bin and Labeling Definitions Decoding Product Bin Labeling In the manufacturing of semiconductor products, there are variations in performance around the average values given in the technical datasheet. For this reason, Lumileds bins LED components for luminous flux or radiometric power, color point, peak or dominant wavelength and forward voltage. LUXEON Z LEDs are labeled using a 4-digit alphanumeric CAT code following the format below: A B C D A - designates luminous fluxbin (example: B=110 to 120 lumens, C=120 to 130 lumens) B C - designates color bin (example: 3L, 3U, 5A, 5B, 5C, 5D) D designates forward voltage bin (example: P=2.50 to 2.75V, R=2.75 to 3.00V) - Therefore, a LUXEON Z with a lumen range of 110 to 120, color bin of 5A and a forward voltage range of 2.75 to 3.00V has the following CAT code: B 5 A R Luminous Flux Bins Table 5 lists the standard luminous flux bins for LUXEON Z emitters. Although several bins are outlined, product availability in a particular bin varies by production run and by product performance. Not all bins are available in all CCTs. Table 5. Luminous flux bin definitions for LUXEON Z. BIN LUMINOUS FLUX [1] (lm) MINIMUM MAXIMUM A 100 110 B 110 120 C 120 130 D 130 140 E 140 150 F 150 160 G 160 170 H 170 180 J 180 190 K 190 200 Notes for Table 5: 1. Lumileds maintains a tolerance of 6.5% on luminous flux measurements. DS120 LUXEON Z Product Datasheet 20170327 (c)2017 Lumileds Holding B.V. All rights reserved. 9 Color Bin Definition 0.430 0.425 NOTE: Color bin space illustration for 2700K, 3000K and 3500K. For CCT above 4000K, the ellipse centers are all above Black Body Line (BBL). 0.420 Bin 5A CIE 1931 y 0.415 Bin 3U[1] Bin 5D B4 0.410 B1 0.400 Bin 5B Bin 3L[2] 0.405 Bin 5C bin 3U denotes the area ABOVE BBL enclosed by 3-step MAE. bin 3L denotes the area BELOW BBL enclosed by 3-step MAE. B1 and B4 are intersection points on BBL [1] Color [2] Color 0.395 0.390 0.445 0.450 0.455 0.460 0.465 0.470 0.475 CIE 1931 x Color Space Definition for Above and Below Black Body Line Parameter Definition of MacAdam Ellipse Figure 7: 3- and 5-step MacAdam ellipse illustration for Table 6. Table 6. 3- and 5-step MacAdam ellipse color bin definitions for LUXEON Z. NOMINAL CCT COLOR SPACE CENTER POINT [1] (cx, cy) MAJOR AXIS, a MINOR AXIS, b ELLIPSE ROTATION ANGLE, 2700K Single 3-step MacAdam ellipse (0.4578, 0.4101) 0.00810 0.00420 53.70 3000K Single 3-step MacAdam ellipse (0.4338, 0.4030) 0.00834 0.00408 53.20 3500K Single 3-step MacAdam ellipse (0.4073, 0.3917) 0.00927 0.00414 54.00 4000K Single 3-step MacAdam ellipse (0.3818, 0.3797) 0.00939 0.00402 53.70 5000K Single 3-step MacAdam ellipse (0.3447, 0.3553) 0.00822 0.00354 59.60 2700K Single 5-step MacAdam ellipse (0.4578, 0.4101) 0.01350 0.00700 53.70 3000K Single 5-step MacAdam ellipse (0.4338, 0.4030) 0.01390 0.00680 53.20 3500K Single 5-step MacAdam ellipse (0.4073, 0.3917) 0.01545 0.00690 54.00 4000K Single 5-step MacAdam ellipse (0.3818, 0.3797) 0.01565 0.00670 53.70 5000K Single 5-step MacAdam ellipse (0.3447, 0.3553) 0.01370 0.00590 59.60 5700K Single 5-step MacAdam ellipse (0.3287, 0.3417) 0.01243 0.00533 59.09 6500K Single 5-step MacAdam ellipse (0.3123, 0.3282) 0.01115 0.00475 58.57 Notes for Table 6: 1. Lumileds maintains a tolerance of 0.005 on x and y coordinates in the CIE 1931 color space. Forward Voltage Bins Table 7. Forward voltage bin definitions for LUXEON Z. BIN FORWARD VOLTAGE [1] (Vf) MINIMUM MAXIMUM P 2.50 2.75 R 2.75 3.00 S 3.00 3.25 Notes for Table 7: 1. Lumileds maintains a tolerance of 0.06V on forward voltage measurements. DS120 LUXEON Z Product Datasheet 20170327 (c)2017 Lumileds Holding B.V. All rights reserved. 10 Mechanical Dimensions Figure 8: Mechanical dimensions for LUXEON Z. Notes for Figure 8: 1. Drawings are not to scale. 2. All dimensions are in millimeters. DS120 LUXEON Z Product Datasheet 20170327 (c)2017 Lumileds Holding B.V. All rights reserved. 11 Reflow Soldering Guidelines tp Tp Critical Zone TL to Tp Ramp-up TL Temperature tL Tsmax Tsmin Ramp-down ts Preheat Area 25 Time 25C to Peak JEDEC J-STD-020D Time Figure 9: Visualization of the acceptable reflow temperature profile as specified in Table 8. Table 8. Reflow profile characteristics for LUXEON Z. PROFILE FEATURE LEAD FREE ASSEMBLY Preheat Minimum Temperature (Tsmin) 150C Preheat Maximum Temperature (Tsmax) 200C Preheat Time (tsmin to tsmax) 60 to 180 seconds Ramp-Up Rate (TL to Tp) 3C / second maximum Liquidus Temperature (TL) 217C Time Maintained Above Temperature TL (tL) 60 to 150 seconds Peak / Classification Temperature (Tp) 260C Time Within 5C of Actual Temperature (tp) 20 to 40 seconds Ramp-Down Rate (Tp to TL) 6C / second maximum Time 25C to Peak Temperature 8 minutes maximum JEDEC Moisture Sensitivity Table 9. Moisture sensitivity levels for LUXEON Z. LEVEL 1 FLOOR LIFE SOAK REQUIREMENTS STANDARD TIME CONDITIONS TIME CONDITIONS Unlimited 30C / 85% RH 168 Hours +5 / -0 85C / 85% RH DS120 LUXEON Z Product Datasheet 20170327 (c)2017 Lumileds Holding B.V. All rights reserved. 12 Solder Pad Design Figure 10: Recommended PCB solder pad layout for LUXEON Z. Notes for Figure 10: 1. Drawings are not to scale. 2. All dimensions are in millimeters. DS120 LUXEON Z Product Datasheet 20170327 (c)2017 Lumileds Holding B.V. All rights reserved. 13 Packaging Information Pocket Tape Dimensions SPROCKET HOLE O1.50.1 40.1 1.750.1 1.900.05 8+0.3 -0.1 5 MAX 0.200.02 0.880.05 5 MAX 1.500.05 Figure 11: Pocket tape dimensions for LUXEON Z. Notes for Figure 11: 1. Drawings are not to scale. 2. All dimensions are in millimeters. DS120 LUXEON Z Product Datasheet 20170327 (c)2017 Lumileds Holding B.V. All rights reserved. 14 Reel Dimensions Figure 12: Reel dimensions for LUXEON Z. Notes for Figure 12: 1. Drawings are not to scale. 2. All dimensions are in millimeters. DS120 LUXEON Z Product Datasheet 20170327 (c)2017 Lumileds Holding B.V. All rights reserved. 15 About Lumileds Lumileds is the global leader in light engine technology. The company develops, manufactures and distributes groundbreaking LEDs and automotive lighting products that shatter the status quo and help customers gain and maintain a competitive edge. With a rich history of industry "firsts," Lumileds is uniquely positioned to deliver lighting advancements well into the future by maintaining an unwavering focus on quality, innovation and reliability. To learn more about our portfolio of light engines, visit lumileds.com. (c)2017 Lumileds Holding B.V. All rights reserved. LUXEON is a registered trademark of the Lumileds Holding B.V. in the United States and other countries. lumileds.com DS120 LUXEON Z Product Datasheet 20170327 Neither Lumileds Holding B.V. nor its affiliates shall be liable for any kind of loss of data or any other damages, direct, indirect or consequential, resulting from the use of the provided information and data. Although Lumileds Holding B.V. and/or its affiliates have attempted to provide the most accurate information and data, the materials and services information and data are provided "as is," and neither Lumileds Holding B.V. nor its affiliates warrants or guarantees the contents and correctness of the provided information and data. Lumileds Holding B.V. and its affiliates reserve the right to make changes without notice. You as user agree to this disclaimer and user agreement with the download or use of the provided materials, information and data.