30
®
DESCRIPTION
The single output DGP30 Series is designed to accept an extended
2:1 input voltage range for use in industrial and telecom
applications. The output of the converter is electrically isolated,
thereby allowing the output to be configured as a positive or
negative output voltage. For additional system utility output Trim
and Remote ON/OFF are featured. Overcurrent protection,
overtemperature protection, and output overvoltage transient
protection allow safe, reliable operation.
FEATURES
• Remote ON/OFF and TRIM
• Low OFF Current
• Overcurrent and Overtemperature Protection
• Efficiencies to 86%
• Transient Output Overvoltage Protection
• 1544V Isolation
• Five-Side Shielded Case
• Extended Range Input (2:1)
DGP30 SERIES
SINGLE OUTPUT
Mechanical tolerances unless otherwise noted:
X.XX dimensions: ±0.020 inches
X.XXX dimensions: ±0.005 inches
niP noitcnuF
1TUPNI+
2TUPNI-
3FFO/NO
4NIPON
5TUO+
6TUO-
7MIRT
snoitacificepSlareneG )1(
sledoMllA stinU
)2(noitcnuFFFO/NO
leveLcigoLNO
nepOniPro NIM0.8CDV
leveLcigoLFFOXAM0.2CDV
ecnatsiseRtupnIPYT001smhoK
tnerruCeldIretrevnoC
woLniPFFO/NO PYT1<Am
n (3)oitalosI egatloVnoitalosI 01 µegakaeLA tuptuO-tupnI NIM4451CDV
tuptuOottupnI
ecnaticapaC PYT003Fp
n (4)oitcnuFmirTtuptuO ecnatsiseRtupnIPYT02smhoK
egnaRgnimmargorPNIM±5%
latnemnorivnE cT,egnaRgnitarepOesaC
gnitareDoN NIM
XAM 04-
09+ °C
egnaRegarotS NIM
XAM 55-
501 °C
)5(ecnadepmIlamrehTPYT01°ttaW/C
nwodtuhSlamrehT erutarepmeTesaC PYT001°C
lareneG )detaluclaC(FBTMPYT000,008SRH
thgieWtinUPYT45/9.1mg/zo
tiKgnitnuoMsissahC 2A1MC
NOTES
(1) All parameters measured at Tc = 25°C, nominal input voltage and full rated load unless otherwise noted.
Refer to the DC/DC Technical Reference Section for the definition of terms, measurement circuits and
other information.
(2) ON/OFF pin is referenced to pin 2, -Input. See DGP30 Series Application Notes for the specific
requirements of this feature.
(3) The Case is electrically connected to Pin 1, +Input.
(4) Full output trim range may not be available at minimum input voltage and full load. Full trim is
guaranteed from minimum input voltage, plus 5%, and full load.
(5) The case thermal impedance is specified as the case temperature rise over ambient per package watt
dissipated.
1
BOTTOM VIEW SIDE VIEW
0.000
0.000
0.3
0.000
2.02
(51.31)
(7.62)
0.040 (1.02) DIA
7 PLACES
0.55
1.62
(13.97)
(41.15)
2
37
6
5
4
1.800
0.11
1.100
0.700
0.400
0.100
0.600
0.300
0.31
(10.16)
(2.54)
(7.62)
(7.9)
(27.94)
(17.78)
(15.24)
(2.8)
(45.72)
trahCnoitceleS
ledoM egnaRtupnI CDV tuptuO CDV tuptuO Am
niM xaM
5S84E03PGD 63275 0005
21S84E03PGD 6327210052
51S84E03PGD 6327510005