185684K63RFC - Cornell Dubilier Electronics, Inc.

Type 168/185 Metallized Polyester Radial Lead Capacitors

Specifications

Radial Box Metallized Polyester Capacitors for Automatic Insertion

Highlights

♦ Rugged plastic case

♦ Case and epoxy fill meets UL94V-0

♦ 5.0 mm (0.197”) lead spacing

♦ Bulk, tape and reel or ammo pack

♦ Non-inductively wound

♦ Non-polar

♦ Low leakage

Capacitance Range:

Voltage Range:

Capacitance Tolerance:

Operating Temperature Range:

Dielectric Withstand Voltage:

Dissipation Factor (DF):

0.001 µF to 1.0 µF

50 Vdc to 400 Vdc (30 Vac to 200 Vac, 60 Hz)

±5%, ±10%, ±20%

–55 ºC to +125 ºC (with 50% Vdc derating >85 ºC)

1.6 x rated voltage for 2 sec @ +25 ºC ±5 ºC

tgδ x 10 –4 at 25 ºC ±5 ºC

The Type 168/185 series radial lead metallized polyester

box capacitors are available in bulk (Type 168) or on ammo

pack or radial tape and reel (Type 185). These capacitors

are constructed in rugged rectangular plastic cases and all

come with 5.0 mm (0.197”) lead spacing. They are good

for general purpose applications such as bypass, decoupling,

energy storage/discharge and arc suppression.

Total Self Inductance (L):

Maximum Pulse Rise Time (dv/dt):

Long Term Stability (after two years):Capacitance change ∆C/C ≤ ±3% under standard

environmental conditions

If the working voltage (V) is less than the nominal voltage (Vn),

the capacitor can work at higher dv/dt. In this case, the maxi-

mum value allowed is obtained by multiplying the above value

with the ratio Vn/V.

Approximately 7 nH

kHz C ≤0.1 µF C > 0.1 µF

1≤100 ≤100

10 ≤150 ≤150

100 ≤300

Vn V/ms

50 5

63 15

100 24

250 44

400 100

CDE Cornell Dubilier•1605 E. Rodney French Blvd.•New Bedford, MA 02744•Ph: (508)996-8561•Fax: (508)996-3830• www.cde.com

Type 168/185 Metallized Polyester Radial Lead Capacitors

Capacitor Outline Drawing

Ratings

Test Method and Performance

Max

±.015

(±0.4 mm)

.217 ±.039

(5.5 ±1.0 mm)

* Indicates capacitance tolerance: J = ±5%, K = ±10%, M = ±20%

# Indicates packaging type: R = Tape and Reel, A = Ammo Pack

> Indicates tooling code: A = 16.5 mm, B = 18.5 mm, C = 16.0 mm (See H dimension in taping specifications)

Test Conditions

Soldering Temperature 260 ºC ±5 ºC

Soldering Duration 10 sec ±1 sec

Performance

Capacitance Change ∆C/C ≤ ±2%

DF Change ∆tgδ≤

30 x 10–4 at 10 kHz

Insulation Resistance ≥ limit value

Soldering

Lead length shown is as supplied on the 168 Series

Test Conditions

Temperature 25 ºC ±5 ºC

Voltage Charge Time 1 minute

Voltage Charge 50 Vdc for Vn < 100 Vdc

100 Vdc for Vn ≥ 100 Vdc

Performance

For Vn > 100 Vdc ≥30,000 MΩ

For Vn ≤100 Vdc ≥10,000 MΩ for C ≤ 0.1µF

≥1,000 MΩ x µF for C > 0.1µF

Test Conditions

Temperature +40 ºC

Relative Humidity 95%

Test Duration 21 days

Performance

Capacitance Change ∆C/C ≤ ±5%

DF Change ∆tgδ≤30 x 10–4 at 1 kHz

Insulation Resistance ≥ 50% of limit value

Test Conditions

Temperature +85 ºC

Test Duration 1000 hrs

Voltage Applied 1.25 x Vn

Performance

Capacitance Change ∆C/C ≤ ±5%

DF Change ∆tgδ≤30 x 10–4 at 10 kHz

Insulation Resistance ≥ 50% of limit value

Insulation Resistance

Damp Heat Test

Life Test

Catalog Tape & Reel Cap

Part Number Ammo Pack (µF) L T H S Ød L T H S Ød

168104*50A 185104*50#A> 0.10 0.283 0.098 0.256 0.197 0.024 7.2 2.5 6.5 5.0 0.6

168154*50A 185154*50#A> 0.15 0.283 0.098 0.256 0.197 0.024 7.2 2.5 6.5 5.0 0.6

168224*50C 185224*50#C> 0.22 0.283 0.138 0.295 0.197 0.024 7.2 3.5 7.5 5.0 0.6

168334*50C 185334*50#C> 0.33 0.283 0.138 0.295 0.197 0.024 7.2 3.5 7.5 5.0 0.6

168474*50H 185474*50#H> 0.47 0.283 0.177 0.335 0.197 0.024 7.2 4.5 8.5 5.0 0.6

168684*50F 185684*50#F> 0.68 0.283 0.197 0.394 0.197 0.024 7.2 5.0 10.0 5.0 0.6

168824*50G 185824*50#G> 0.82 0.283 0.236 0.433 0.197 0.024 7.2 6.0 11.0 5.0 0.6

168105*50G 185105*50#G> 1.00 0.283 0.236 0.433 0.197 0.024 7.2 6.0 11.0 5.0 0.6

168473*63A 185473*63#A> 0.047 0.283 0.098 0.256 0.197 0.024 7.2 2.5 6.5 5.0 0.6

168563*63A 185563*63#A> 0.056 0.283 0.098 0.256 0.197 0.024 7.2 2.5 6.5 5.0 0.6

168683*63A 185683*63#A> 0.068 0.283 0.098 0.256 0.197 0.024 7.2 2.5 6.5 5.0 0.6

168823*63A 185823*63#A> 0.082 0.283 0.098 0.256 0.197 0.024 7.2 2.5 6.5 5.0 0.6

168104*63A 185104*63#A> 0.10 0.283 0.098 0.256 0.197 0.024 7.2 2.5 6.5 5.0 0.6

168154*63C 185154*63#C> 0.15 0.283 0.138 0.295 0.197 0.024 7.2 3.5 7.5 5.0 0.6

168184*63C 185184*63#C> 0.18 0.283 0.138 0.295 0.197 0.024 7.2 3.5 7.5 5.0 0.6

168224*63C 185224*63#C> 0.22 0.283 0.138 0.295 0.197 0.024 7.2 3.5 7.5 5.0 0.6

168274*63C 185274*63#C> 0.27 0.283 0.138 0.295 0.197 0.024 7.2 3.5 7.5 5.0 0.6

168334*63H 185334*63#H> 0.33 0.283 0.177 0.335 0.197 0.024 7.2 4.5 8.5 5.0 0.6

168474*63H 185474*63#H> 0.47 0.283 0.177 0.335 0.197 0.024 7.2 4.5 8.5 5.0 0.6

168684*63F 185684*63#F> 0.68 0.283 0.197 0.394 0.197 0.024 7.2 5.0 10.0 5.0 0.6

168105*63G 185105*63#G> 1.00 0.283 0.236 0.433 0.197 0.024 7.2 6.0 11.0 5.0 0.6

Inches Millimeters

50 Vdc / 30 Vac

63 Vdc / 40 Vac

CDE Cornell Dubilier•1605 E. Rodney French Blvd.•New Bedford, MA 02744•Ph: (508)996-8561•Fax: (508)996-3830• www.cde.com

Type 168/185 Metallized Polyester Radial Lead Capacitors

* Indicates capacitance tolerance: J = ±5%, K = ±10%, M = ±20%

# Indicates packaging type: R = Tape and Reel, A = Ammo Pack

> Indicates tooling code: A = 16.5 mm, B = 18.5 mm, C = 16.0 mm (See H dimension in taping specification)

Catalog Tape & Reel Cap

Part Number Ammo Pack (µF) L T H S Ød L T H S Ød

168102*100A 185102*100#A> 0.0010 0.283 0.098 0.256 0.197 0.024 7.2 2.5 6.5 5.0 0.6

168152*100A 185152*100#A> 0.0015 0.283 0.098 0.256 0.197 0.024 7.2 2.5 6.5 5.0 0.6

168222*100A 185222*100#A> 0.0022 0.283 0.098 0.256 0.197 0.024 7.2 2.5 6.5 5.0 0.6

168272*100A 185272*100#A> 0.0027 0.283 0.098 0.256 0.197 0.024 7.2 2.5 6.5 5.0 0.6

168332*100A 185332*100#A> 0.0033 0.283 0.098 0.256 0.197 0.024 7.2 2.5 6.5 5.0 0.6

168392*100A 185392*100#A> 0.0039 0.283 0.098 0.256 0.197 0.024 7.2 2.5 6.5 5.0 0.6

168472*100A 185472*100#A> 0.0047 0.283 0.098 0.256 0.197 0.024 7.2 2.5 6.5 5.0 0.6

168562*100A 185562*100#A> 0.0056 0.283 0.098 0.256 0.197 0.024 7.2 2.5 6.5 5.0 0.6

168682*100A 185682*100#A> 0.0068 0.283 0.098 0.256 0.197 0.024 7.2 2.5 6.5 5.0 0.6

168822*100A 185822*100#A> 0.0082 0.283 0.098 0.256 0.197 0.024 7.2 2.5 6.5 5.0 0.6

168103*100A 185103*100#A> 0.010 0.283 0.098 0.256 0.197 0.024 7.2 2.5 6.5 5.0 0.6

168153*100A 185153*100#A> 0.015 0.283 0.098 0.256 0.197 0.024 7.2 2.5 6.5 5.0 0.6

168183*100A 185183*100#A> 0.018 0.283 0.098 0.256 0.197 0.024 7.2 2.5 6.5 5.0 0.6

168223*100A 185223*100#A> 0.022 0.283 0.098 0.256 0.197 0.024 7.2 2.5 6.5 5.0 0.6

168273*100A 185273*100#A> 0.027 0.283 0.098 0.256 0.197 0.024 7.2 2.5 6.5 5.0 0.6

168333*100C 185333*100#C> 0.033 0.283 0.138 0.295 0.197 0.024 7.2 3.5 7.5 5.0 0.6

168393*100C 185393*100#C> 0.039 0.283 0.138 0.295 0.197 0.024 7.2 3.5 7.5 5.0 0.6

168473*100C 185473*100#C> 0.047 0.283 0.138 0.295 0.197 0.024 7.2 3.5 7.5 5.0 0.6

168683*100H 185683*100#H> 0.068 0.283 0.177 0.335 0.197 0.024 7.2 4.5 8.5 5.0 0.6

168104*100H 185104*100#H> 0.10 0.283 0.177 0.335 0.197 0.024 7.2 4.5 8.5 5.0 0.6

168154*100F 185154*100#F> 0.15 0.283 0.197 0.394 0.197 0.024 7.2 5.0 10.0 5.0 0.6

168224*100G 185224*100#G> 0.22 0.283 0.236 0.433 0.197 0.024 7.2 6.0 11.0 5.0 0.6

168332*250A 185332*250#A> 0.0033 0.283 0.098 0.256 0.197 0.024 7.2 2.5 6.5 5.0 0.6

168472*250A 185472*250#A> 0.0047 0.283 0.098 0.256 0.197 0.024 7.2 2.5 6.5 5.0 0.6

168682*250A 185682*250#A> 0.0068 0.283 0.098 0.256 0.197 0.024 7.2 2.5 6.5 5.0 0.6

168103*250A 185103*250#A> 0.010 0.283 0.098 0.256 0.197 0.024 7.2 2.5 6.5 5.0 0.6

168153*250A 185153*250#A> 0.015 0.283 0.098 0.256 0.197 0.024 7.2 2.5 6.5 5.0 0.6

168223*250C 185223*250#C> 0.022 0.283 0.138 0.295 0.197 0.024 7.2 3.5 7.5 5.0 0.6

168333*250C 185333*250#C> 0.033 0.283 0.138 0.295 0.197 0.024 7.2 3.5 7.5 5.0 0.6

168473*250F 185473*250#F> 0.047 0.283 0.197 0.394 0.197 0.024 7.2 5.0 10 5.0 0.6

168683*250F 185683*250#F> 0.068 0.283 0.197 0.394 0.197 0.024 7.2 5.0 10 5.0 0.6

168104*250G 185104*250#G> 0.100 0.283 0.236 0.433 0.197 0.024 7.2 6.0 11 5.0 0.6

168102*400A 185102*400#A> 0.001 0.283 0.098 0.256 0.197 0.024 7.2 2.5 6.5 5.0 0.6

168152*400A 185152*400#A> 0.002 0.283 0.098 0.256 0.197 0.024 7.2 2.5 6.5 5.0 0.6

168222*400A 185222*400#A> 0.002 0.283 0.098 0.256 0.197 0.024 7.2 2.5 6.5 5.0 0.6

168332*400C 185332*400#C> 0.003 0.283 0.138 0.295 0.197 0.024 7.2 3.5 7.5 5.0 0.6

168472*400C 185472*400#C> 0.005 0.283 0.138 0.295 0.197 0.024 7.2 3.5 7.5 5.0 0.6

168682*400C 185682*400#C> 0.007 0.283 0.138 0.295 0.197 0.024 7.2 3.5 7.5 5.0 0.6

168103*400F 185103*400#F> 0.010 0.283 0.197 0.394 0.197 0.024 7.2 5.0 10 5.0 0.6

168153*400F 185153*400#F> 0.015 0.283 0.197 0.394 0.197 0.024 7.2 5.0 10 5.0 0.6

168223*400G 185223*400#G> 0.022 0.283 0.236 0.433 0.197 0.024 7.2 6.0 11 5.0 0.6

400 Vdc / 200 Vac

Inches Millimeters

100 Vdc / 63 Vac

250 Vdc / 160 Vac

CDE Cornell Dubilier•1605 E. Rodney French Blvd.•New Bedford, MA 02744•Ph: (508)996-8561•Fax: (508)996-3830• www.cde.com

Type 168/185 Metallized Polyester Radial Lead Capacitors

Tape Specification - 5.0 mm Lead Spacing

> The H dimension depends on the

insertion equipment used. Specify

the proper tooling code as indicated

below.

Part Numbering System for Auto Insertion

* Tooling code (>) depends on the users insertion equipment requirements. See table for available options.

Case Quantity Quantity

Code Reeled Ammo Pack

A 2500 3500

C 1800 1500

F 1200 1200

G 1000 1000

H 1400 1400

Tooling

Code Millimeters Inches

A16.5±0.75 .679±0.030

B18.5±0.75 .728±0.030

C16.5±0.75 .630±0.030

H Dimensions

185 104 K 100 R H B

Packaging *Tooling

Type Case Code

Series Capacitance Tolerance Voltage (#) Code (>)

185 102 = .001 µF J = ±5% 50 = 50 Vdc A = Ammo A A

103 = .01 µF K = ±10% 63 = 63 Vdc R = Tape & Reel C B

104 = .1 µF M = ±20% 100 = 100 Vdc F C

105 = 1.0 µF 250 = 250 Vdc G

400 = 400 Vdc H

Lead-Wire Diameter Ød 0.6+0.04 –0.01 .024±.001

Lead-to-Lead Distance P 5.0+0.6 –0.2 .197+.024 –.040

Feed Hole Pitch P012.7±0.3 .5±.012

Pitch of Component P112.7±1.0 .5±.039

Hole Center to Lead P23.85±0.7 .152±.028

Feed Hole Center to P36.35±1.3 .250±.051

Component Center

Component Alignment, F-R ∆h0

±2.0 0±.079

Tape Width W 18+1.0 –0.1 .709+.039 –.004

Hold-down Tape Width W06.0 min .236 min

Hole Position W19.0+0.75 –0.05 .355+.030 –.001

Hold-down Tape Position W23.0 Max .118 Max

Height of Component H > >

from Tape Center

Feed Hole Diameter D04.0±0.3 .157±.012

Item Code Millimeters Inches

CDE Cornell Dubilier•1605 E. Rodney French Blvd.•New Bedford, MA 02744•Ph: (508)996-8561•Fax: (508)996-3830• www.cde.com