Order this document by LF347/D These low cost JFET input operational amplifiers combine two state-of-the-art analog technologies on a single monolithic integrated circuit. Each internally compensated operational amplifier has well matched high voltage JFET input devices for low input offset voltage. The JFET technology provides wide bandwidths and fast slew rates with low input bias currents, input offset currents, and supply currents. These devices are available in single, dual and quad operational amplifiers which are pin-compatible with the industry standard MC1741, MC1458, and the MC3403/LM324 bipolar devices. * Input Offset Voltage of 5.0 mV Max (LF347B) * * * * * * * 1 D SUFFIX PLASTIC PACKAGE CASE 751 (SO-8) 1 PIN CONNECTIONS Offset Null 1 Noninvt Input 3 Output A 1 2 Inputs A 3 VEE 4 MAXIMUM RATINGS Symbol Value Unit Supply Voltage VCC VEE +18 -18 V Differential Input Voltage VID 30 V VIDR 15 V tSC Continuous PD 1/JA 900 10 TA 0 to +70 TJ 115 Tstg - 65 to +150 Operating Junction Temperature Range 7 VCC 6 Output VEE 4 High Common Mode and Supply Voltage Rejection Ratios: 100 dB Operating Ambient Temperature Range 8 NC - + Invt Input 2 Low Supply Current: 1.8 mA per Amplifier High Input Impedance: 1012 Storage Temperature Range 8 High Slew Rate: 13V/s Power Dissipation at TA = +25C Derate above TA =+25C 8 Wide Gain Bandwidth: 4.0 MHz Output Short Circuit Duration (Note 2) N SUFFIX PLASTIC PACKAGE CASE 626 Low Input Noise Voltage: 16 nV/ Hz Input Voltage Range (Note 1) FAMILY OF JFET OPERATIONAL AMPLIFIERS Low Input Bias Current: 50 pA Rating LF351 (Top View) 5 Offset Null 8 VCC - + LF353 (Top View) 7 Output B - A B 6 Inputs B 5 + N SUFFIX PLASTIC PACKAGE CASE 646 14 1 PIN CONNECTIONS mW mW/C C Out 1 1 2 14 Out 4 - - 13 Inputs 4 Inputs 1 3 C + 1 4 12 + VCC 4 C 5 11 VEE + Inputs 2 6 NOTES: 1. Unless otherwise specified, the absolute maximum negative input voltage is limited to the negative power supply. 2. Any amplifier output can be shorted to ground indefinitely. However, if more than one amplifier output is shorted simultaneously, maximum junction temperature rating may be exceeded. - + 2 3 10 Inputs 3 - 9 8 Out 3 Out 2 7 (Top View) ORDERING INFORMATION Device Operating Function Temperature Range LF351D LF351N Single Single LF353D LF353N Dual Dual LF347BN LF347N Quad Quad Motorola, Inc. 1996 MOTOROLA ANALOG IC DEVICE DATA Package SO-8 Plastic DIP TA = 0 to +70C SO-8 Plastic DIP Plastic DIP Plastic DIP Rev 0 1 LF347, B LF351 LF353 ELECTRICAL CHARACTERISTICS (VCC = +15 VEE = -15 V, TA = 25C, unless otherwise noted.) LF347B Ch Characteristic i i S b l Symbol LF347, LF351, LF353 U i Unit Min Typ Max Min Typ Max - - 1.0 - 5.0 8.0 - - 5.0 - 10 13 - 10 - - 10 - - - 25 - 100 4.0 - - 25 - 100 4.0 pA nA - - 50 - 200 8.0 - - 50 - 200 8.0 pA nA ri - 1012 - - 1012 - Common Mode Input Voltage Range VICR 11 +15 -12 - 11 +15 -12 - V Large-Signal Voltage Gain (VO = 10 V, RL = 2.0 k) TA = +25C 0C TA +70C AVOL 50 25 100 - - - 25 15 100 - - - VO 12 14 - 12 14 - V Common Mode Rejection (RS 10 k) CMR 80 100 - 70 100 - dB Supply Voltage Rejection (RS 10 k) PSRR 80 100 - 70 100 - Input Offset Voltage (RS 10 k, VCM = 0) TA = +25C 0C TA +70C Avg. Temperature Coefficient of Input Offset Voltage RS 10 k, 0C TA +70C VIO VIO/T Input Offset Current (VCM = 0, Note 3) TA = +25C 0C TA +70C IIO Input Bias Current (VCM = 0, Note 3) TA = +25C 0C TA +70C IIB Input Resistance Output Voltage Swing (RL = 10 k) Supply Current LF347 LF351 LF353 mV V/C V/mV ID dB mA - - - 7.2 - - 11 - - - - - 7.2 1.8 3.6 11 3.4 6.5 Short Circuit Current ISC - 25 - - 25 - mA Slew Rate (AV = +1) SR - 13 - - 13 - V/s Gain-Bandwidth Product BWp - 4.0 - - 4.0 - MHz Equivalent Input Noise Voltage (RS = 100 , f = 1000 Hz) en - 24 - - 24 - nV/ Hz Equivalent Input Noise Current (f = 1000 Hz) in - 0.01 - - 0.01 - pA/ Hz Channel Separation (LF347, LF353) 1.0 Hz f 20 kHz (Input Referred) - - -120 - - -120 - dB For Typical Characteristic Performance Curves, refer to MC34001, 34002, 34004 data sheet. NOTE: 2 3. Input bias currents of JFET input op amps approximately double for every 10C rise in junction temperature. To maintain junction temperatures as close to ambient as is possible, pulse techniques are utilized during test. MOTOROLA ANALOG IC DEVICE DATA LF347, B LF351 LF353 OUTLINE DIMENSIONS N SUFFIX PLASTIC PACKAGE CASE 626-05 ISSUE K 8 5 NOTES: 1. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 2. PACKAGE CONTOUR OPTIONAL (ROUND OR SQUARE CORNERS). 3. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. -B- 1 4 F -A- NOTE 2 DIM A B C D F G H J K L M N L C J -T- N SEATING PLANE D M K G H 0.13 (0.005) M T A B M MILLIMETERS MIN MAX 9.40 10.16 6.10 6.60 3.94 4.45 0.38 0.51 1.02 1.78 2.54 BSC 0.76 1.27 0.20 0.30 2.92 3.43 7.62 BSC --- 10_ 0.76 1.01 INCHES MIN MAX 0.370 0.400 0.240 0.260 0.155 0.175 0.015 0.020 0.040 0.070 0.100 BSC 0.030 0.050 0.008 0.012 0.115 0.135 0.300 BSC --- 10_ 0.030 0.040 M D SUFFIX PLASTIC PACKAGE CASE 751-05 (SO-8) ISSUE R D A NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. DIMENSIONS ARE IN MILLIMETERS. 3. DIMENSION D AND E DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE. 5. DIMENSION B DOES NOT INCLUDE MOLD PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 TOTAL IN EXCESS OF THE B DIMENSION AT MAXIMUM MATERIAL CONDITION. C 8 5 0.25 H E M B M 1 4 h B e X 45 _ q A C SEATING PLANE L 0.10 A1 B 0.25 M C B S A MOTOROLA ANALOG IC DEVICE DATA S DIM A A1 B C D E e H h L q MILLIMETERS MIN MAX 1.35 1.75 0.10 0.25 0.35 0.49 0.18 0.25 4.80 5.00 3.80 4.00 1.27 BSC 5.80 6.20 0.25 0.50 0.40 1.25 0_ 7_ 3 LF347, B LF351 LF353 OUTLINE DIMENSIONS N SUFFIX PLASTIC PACKAGE CASE 646-06 ISSUE L 14 8 1 7 NOTES: 1. LEADS WITHIN 0.13 (0.005) RADIUS OF TRUE POSITION AT SEATING PLANE AT MAXIMUM MATERIAL CONDITION. 2. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 3. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 4. ROUNDED CORNERS OPTIONAL. B A F L C J N H G D SEATING PLANE K M DIM A B C D F G H J K L M N INCHES MIN MAX 0.715 0.770 0.240 0.260 0.145 0.185 0.015 0.021 0.040 0.070 0.100 BSC 0.052 0.095 0.008 0.015 0.115 0.135 0.300 BSC 0_ 10_ 0.015 0.039 MILLIMETERS MIN MAX 18.16 19.56 6.10 6.60 3.69 4.69 0.38 0.53 1.02 1.78 2.54 BSC 1.32 2.41 0.20 0.38 2.92 3.43 7.62 BSC 0_ 10_ 0.39 1.01 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA / EUROPE / Locations Not Listed: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1-800-441-2447 or 602-303-5454 JAPAN: Nippon Motorola Ltd.; Tatsumi-SPD-JLDC, 6F Seibu-Butsuryu-Center, 3-14-2 Tatsumi Koto-Ku, Tokyo 135, Japan. 03-81-3521-8315 MFAX: RMFAX0@email.sps.mot.com - TOUCHTONE 602-244-6609 INTERNET: http://Design-NET.com ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298 4 *LF347/D* MOTOROLA ANALOG IC DEVICE DATA LF347/D