412H/422H/432H Page 1SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE ©2003 TELEDYNE RELAYS
www.teledynerelays.com 412H/422H/432H/1203/Q1
HIGH-PERFORMANCE
SERIES
412H
422H
432H
HIGH-TEMPERATURE (200°C),
HIGH-PERFORMANCE
TO-5 RELAY
DPDT
DESCRIPTION
The TO-5 relay, originally conceived and developed by Teledyne, has become one of the
industry standards for low-level switching from dry circuit to 1 ampere. Designed for high-
density PC board mounting, these TO-5 relays are some of the most versatile
ultraminiature relays available because of their small size and low coil power dissipation.
The H Series high-temperature TO-5 relays are designed for reliable operation in
elevated ambient temperatures up to 200°C. Special material selection and processing
provide assurance of freedom from contact contamination and mechanical
malfunctioning that might otherwise be caused by ultra high ambient temperature
conditions.
Typical applications:
• Oil exploration (down hole) instrumentation
• High temperature industrial and process control instrumentation
By virtue of its inherently low intercontact capacitance and contact circuit losses, the H
Series relays have proven to be excellent ultraminiature RF switches for applications with
frequency ranges well into the UHF spectrum (see Figures 1 and 2).
PRINCIPLE OF OPERATION 422H
Energizing Coil B produces a magnetic field
opposing the holding flux of the permanent magnet
in Circuit B. As this net holding force decreases, the
attractive force in the air gap of circuit A, which also
results from the flux of the permanent magnet,
becomes great enough to break the armature free of
Core B, and snap it into a closed position against
Core A. The armature then remains in this position
upon removal of power from Coil B, but will snap
back to position B upon energizing Coil A. Since operation depends upon cancellation
of a magnetic field, it is necessary to apply the correct polarity to the relay coils as
indicated on the relay schematic.
When latching relays are installed in equipment, the latch and reset coils should not be
pulsed simultaneously. Coils should not be pulsed with less than rated coil voltage and
the pulse width should be a minimum of three times the specified operate time of the
relay. If these conditions are not followed, it is possible for the relay to be in the
magnetically neutral position.
INTERNAL CONSTRUCTION
SERIES
DESIGNATION RELAY TYPE
412H DPDT high-temperature relay
422H DPDT high-temperature magnetic-latching relay
432H DPDT sensitive high-temperature relay
UPPER
STATIONARY
CONTACT
LOWER
STATIONARY
CONTACT
MOVING
CONTACT
UNI-FRAME
ARMATURE
SOFT IRON
ARMATURE
SOFT IRON
CORE B
COIL B
MAGNETIC CIRCUIT B
PERMANENT MAGNET MAGNETIC CIRCUIT A
SOFT IRON FRAME
COIL A
SOFT IRON
CORE A
AIR GAP
STATIONARY
CONTACT
MOVING
CONTACT
412H ENVIRONMENTAL AND
432H PHYSICAL SPECIFICATIONS
Temperature
(Ambient) –65°C to +200°C
Vibration (General Note 1) 30 g’s to 3000 Hz
Shock (General Note 1) 75 g’s,
6 msec, half-sine
Acceleration 50 g’s
Enclosure Hermetically sealed
Weight
412H 0.09 oz. (2.55g) max.
432H 0.15 oz. (4.25g) max.
422H ENVIRONMENTAL AND
PHYSICAL SPECIFICATIONS
Temperature
(Ambient) –65°C to +200°C
Vibration (General Note 1) 30 g’s to 3000 Hz
Shock (General Note 1) 100 g’s,
6 msec, half-sine
Acceleration 50 g’s
Enclosure Hermetically sealed
Weight 0.10 oz. (2.84g) max.
©2003 TELEDYNE RELAYS SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE 412H/422H/432H Page 2
www.teledynerelays.com 412H/422H/432H/1203/Q1
HIGH-PERFORMANCE
SERIES 412H/422H/432H
GENERAL ELECTRICAL SPECIFICATIONS (–65°C to +200°C unless otherwise noted) (Notes 2 & 3)
412H SERIES RELAY
DETAILED ELECTRICAL SPECIFICATIONS (–65°C to +200°C unless otherwise noted) (Note 2)
Contact Arrangement 2 Form C (DPDT)
Rated Duty Continuous
Contact Resistance 412H/432H: 0.125 ohms max. before life; 0.225 ohms max. after life at 1A/28Vdc
422H: 0.15 ohms max. before life; .25 ohms max after life at 1A/28Vdc
Contact Load Ratings (DC)
(See Fig. 3 for other DC
resistive voltage/current ratings)
Resistive: 1 Amp/28Vdc
Inductive: 200 mA/28Vdc (320 mH)
Lamp: 100 mA/28Vdc
Low Level: 10 to 50μA/10 to 50mV
Contact Load Ratings (AC)
(Note 4)
Resistive: 250 mA/115Vac, 60 and 400 Hz (Case not grounded)
100 mA/115Vac, 60 and 400 Hz (Case grounded)
Contact Life Ratings (Note 4)
10,000,000 cycles (typical) at low level
1,000,000 cycles (typical) at 0.5A/28Vdc resistive
100,000 cycles min. at all other loads specified above
Contact Overload Rating 2A/28Vdc Resistive (100 cycles min.)
Contact Carry Rating Contact factory
Coil Operating Power 412H: 450 mW typ. @ 25°C 422H: 290 mW typ. @ 25°C 432H 200 mW typ. @ 25°C
Operate Time 412H: 2.0 msec max. 422H: 1.5 msec max. 432H: 4.0 msec. max
Release Time 2.0 msec max.
Contact Bounce 1.5 msec max.
Intercontact Capacitance 0.4 pf typical
Insulation Resistance 10,000 megohms min. between mutually isolated terminals
Dielectric Strength Atmospheric pressure: 500 Vrms/60Hz 70,000 ft.: 125 Vrms/60Hz
Minimum Operate Pulse 4.5 msec width @ rated voltage (422H only)
BASE PART
NUMBERS 412H-5 412H-6 412H-9 412H-12 412H-18 412H-26
Coil Voltage (Vdc) Nom. 5.0 6.0 9.0 12.0 18.0 26.5
Max. 5.8 8.0 12.0 16.0 24.0 32.0
Coil Resistance (Ohms ±10% @25°C) 50 98 220 390 880 1560
Pick-up Voltage (Vdc, Max.) 4.7 5.9 9.0 11.9 17.8 24.0
Drop-out Voltage (Vdc) Min. 0.14 0.18 0.35 0.41 0.59 0.89
Max. 2.4 3.4 5.1 6.8 10.2 13.5
}measured 1/8" below header
422H SERIES RELAY
DETAILED ELECTRICAL SPECIFICATIONS (–65°C to +200°C unless otherwise noted) (Note 2)
BASE PART
NUMBERS 422H-5 422H-6 422H-9 422H-12 422H-18 422H-26
Coil Voltage (Vdc) Nom. 5.0 6.0 9.0 12.0 18.0 26.5
Max. 5.8 8.0 12.0 16.0 24.0 32.0
Coil Resistance (Ohms ±10% @25°C) 61 120 280 500 1130 2000
Set & Reset Voltage (Vdc, Max.) 4.7 5.9 9.0 11.9 17.8 24.0
432H SERIES RELAY
DETAILED ELECTRICAL SPECIFICATIONS (–65°C to +200°C unless otherwise noted) (Note 2)
BASE PART
NUMBERS 432H-5 432H-6 432H-9 432H-12 432H-18 432H-26
Coil Voltage (Vdc) Nom. 5.0 6.0 9.0 12.0 18.0 26.5
Max. 5.8 8.0 12.0 16.0 24.0 32.0
Coil Resistance (Ohms ±10% @25°C) 100 200 400 850 1600 3300
Pick-up Voltage (Vdc, Max.) 4.7 5.9 9.0 11.9 17.8 24.0
Drop-out Voltage (Vdc) Min. 0.14 0.18 0.35 0.41 0.59 0.89
Max. 2.4 3.4 5.1 6.8 10.2 13.5
412H/422H/432H Page 3SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE ©2003 TELEDYNE RELAYS
www.teledynerelays.com 412H/422H/432H/1203/Q1
HIGH-PERFORMANCE
PERFORMANCE CURVES
(NOTE 2)
10
1
2
3
4
5
6
7
8
9
CASE DETAIL
.370
(9.40)
DIA. MAX.
.031 (0.79)
± .003 (0.08)
.035 (0.89)
± .010 (0.25)
.200 (5.08)
± .010 (.25) DIA. 36°±3° TYP.
412H/432H
.335
(8.51)
DIA. MAX.
A
WIRE LEAD: .75 (19.05) MIN.
.017 (.43) DIA.
+.002 (.05)
±.001 (.03)
.031 (0.79)
± .003 (0.08)
.035 (0.89)
± .010 (0.25)
.200 (5.08)
± .010 (.25) DIA. 36°±3° TYP.
422H
DIMENSIONS ARE SHOWN IN INCHES (MILLIMETERS)
TERMINAL LOCATIONS AND PIN NUMBERS (REF. ONLY)
(Viewed from Terminals)
DIMENSION
“A” MAX.
412H
432H
422H
.270
(6.86)
.375
(9.52)
.280
(7.11)
OUTLINE DIMENSIONS
GENERAL NOTES
1. Relay contacts will exhibit no chatter in excess of 10 μsec or
transfer in excess of 1 μsec.
2. “Typical” characteristics are based on available data and are
best estimates. No on-going verification tests are performed.
3. Characteristics are subject to change after life.
4. Contact load ratings and contact life ratings are based on
similarity testing at 125°C. No 200°C testing is performed.
SCHEMATICS ARE VIEWED FROM TERMINALS
412H 432H 422H
COIL B
COIL A
CONTACTS SHOWN IN POSITION RESULTING
WHEN COIL A LAST ENERGIZED.
SCHEMATIC DIAGRAMS
0
.1
.2
.3
.4
10
20
30
40
50
60
70
.01 0.5 .1 .5 1.0
FREQUENCY (GHz)
FIGURE 1 (412H AND 432H)
TYPICAL RF PERFORMANCE
1.92
1.22
1.07
1.02
1.01
1.00
1.00
VSWR
300
250
200
150
100
50
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0
LOAD CURRENT (AMPS DC)
FIGURE 3
TYPICAL DC CONTACT RATING (RESISTIVE)
LOAD VOLTAGE (VDC)
dB
INSERTION LOSS
RETURN LOSS (VSWR)
ISOLATION ACROSS CONTACTS
ISOLATION ACROSS POLES
0
.1
.2
.3
.4
10
20
30
40
50
60
70
.01 0.5 .1 .5 1.0
FREQUENCY (GHz)
FIGURE 2 (422H)
TYPICAL RF PERFORMANCE
1.92
1.22
1.07
1.02
1.01
1.00
1.00
VSWR
dB
INSERTION LOSS
RETURN LOSS (VSWR)
ISOLATION ACROSS CONTACTS
ISOLATION ACROSS POLES
SERIES 412H/422H/432H
Pad designation and
bottom view dimensions Height For use with the following: Dim. H
Max.
“M4” Pad for TO-5
ER411T
ER412, ER412D, ER412DD .295 (7.49)
712, 712D, 712TN,
RF300, RF310, RF320 .300 (7.62)
ER420, ER422D, ER420DD, 421,
ER421D, ER421DD, ER422, ER422D,
ER422DD, 722, 722D, RF341
.305 (7.75)
ER431T, ER432T,
ER432, ER432D, ER432DD .400 (10.16)
732, 732D, 732TN, RF303, RF313,
RF323 .410 (10.41)
RF312 .350 (8.89)
“M4” Pad for TO-5
ER411, ER411D, ER411DD .295 (7.49)
ER431, ER431D, ER431DD .400 (10.16)
RF311 .300 (7.62)
RF331 .410 (10.41)
“M4” Pad for Centigrid®
172, 172D .305 (7.75)
ER114, ER114D, ER114DD,
J114, J114D, J114DD .300 (7.62)
ER134, ER134D, ER134DD,
J134, J134D, J134DD .400 (10.16)
RF100 .315 (8.00)
RF103 .420 (10.67)
“M9” Pad for Centigrid®
122C, A152 .320 (8.13)
ER116C, J116C .300 (7.62)
ER136C, J136C .400 (10.16)
RF180 .325 (8.25)
A150 .305 (7.75)
Notes:
1. Spacer pad material: Polyester  lm.
2. To specify an “M4” or “M9” spacer pad, refer to the mounting variants portion of the part numbering
example in the applicable datasheet.
3. Dimensions are in inches (mm).
4. Unless otherwise speci ed, tolerance is ± .010 (.25).
5. Add 10 m to the contact resistance show in the datasheet.
6. Add 0.01 oz. (0.25 g) to the weight of the relay assembly shown in the datasheet.
Ø.150
[3.81]
(REF)
Dim H
MAX
Dim H
MAX
Dim H
MAX
.156
[3.96]
(REF)
.256
[6.5]
(REF)
Dim H
MAX
Appendix A: Spacer Pads
© 2008 Teledyne Relays SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
Pad designation and
bottom view dimensions Height For use with the following: Dim. H
Max.
“M” Pad 5/ 6/
ER411T, J411T, ER412, ER412D
ER412DD, J412, J412D, J412DD
ER412T, J412T
.388 (9.86)
712, 712D, 712TN .393 (9.99)
ER431T, J431T, ER432, ER432D
ER432DD, J432, J432D, J432DD
ER432T, J432T
.493 (12.52)
732, 732D, 732TN .503 (12.78)
ER420, J420, ER420D, J420D
ER420DD, J420DD, ER421, J421
ER421D, J421D, ER421DD
J422D, ER422DD, J422DD, 722
.398 (10.11)
“M2” Pad 7/ 8/
ER411T
ER412, ER412D, ER412DD
J412, J412D, J412DD
.441 (11.20)
712, 712D .451 (11.46)
ER421, ER421D, ER421DD
722, 732D .451 (11.46)
ER431T
ER432, ER432D, ER432DD .546 (13.87)
732, 732D .556 (14.12)
“M3” Pad 5/ 6/ 9/
ER411, ER411D, ER411DD
ER411TX
ER412X, ER412DX, ER412DDX
ER412TX
.388 (9.86)
712X, 712DX, 712TNX .393 (9.99)
ER420X, ER420DX, ER420DDX
ER421X, ER421DX, ER421DDX
ER422X, ER422DX
ER422DDX, 722X, 722DDX
.398 (10.11)
ER431, ER431D, ER431DD
ER431TX
ER432X, ER432DX, ER432DDX
ER432TX
.493 (12.52)
732X, 732DX, 732TNX .503 (12.78)
Notes:
1. Spreader pad material: Diallyl Phthalate.
2. To specify an “M”, “M2” or “M3” spreader pad, refer to the mounting variants portion of the part number example
in the applicable datasheet.
3. Dimensions are in inches (mm).
4. Unless otherwise speci ed, tolerance is ± .010” (0.25).
5/. Add 25 m to the contact resistance shown in the datasheet.
6/. Add .01 oz. (0.25 g) to the weight of the relay assembly shown in the datasheet.
7/. Add 50 m to the contact resistance shown in the datasheet.
8/. Add 0.025 oz (0.71 g) to the weight of the relay assembly shown in the datasheet.
9/. M3 pad to be used only when the relay has a center pin (e.g. ER411M3-12A, 722XM3-26.)
.370 [9.4]
MAX SQ
.150
[3.81]
.100
[2.54]
.200
[5.08]
.300
[7.62]
.100
[2.54]
Dim H
MAX
.370
[9.4]
MIN
.014
[0.36]
(REF)
.390 [9.91]
SQ
.300
[7.62]
.100
[2.54]
.300
[7.62]
.100
[2.54] .150
[3.81]
.150
[3.81]
.130
[3.3]
Dim H
MAX
.370 [9.4]
MAX SQ
.150
[3.81]
.100
[2.54]
.200
[5.08]
.300
[7.62]
.100
[2.54]
Dim H
MAX
.370
[9.4]
MIN
.014
[0.36]
(REF)
Appendix A: Spreader Pads
(800) 284-7007 • www.teledynerelays.com +44 (0) 1236 453124 • www.teledyne-europe.com © 2008 Teledyne Relays
.100
[2.54]
.100
[2.54]
.100
[2.54]
"Y" POSITION
"Z" POSITION
.100
[2.54]
.100
[2.54]
.100
[2.54]
"W" POSITION
"U" POSITION
(ER116C and ER136C only)
"X" POSITION
"Z" POSITION
"Y" POSITION
.050
[1.27]
36°±3°
Ø.200
[Ø5.08]
"Z" POSITION
"Y" POSITION
"X" POSITION
45°±3°
"Z" POSITION
"Y" POSITION
Ø.200
[Ø5.08]
Centigrid® Relays:
RF100, RF103, ER114, ER134, 172
Centigrid® Relays:
RF180, ER116C, 122C, ER136C
TO-5 Relays:
ER411T, ER412, ER412T, ER420, ER421, ER422,
ER431T, ER432, ER432T, 712, 712TN, 400H, 400K,
400V, RF300, RF303, RF341, RF312, RF310, RF313,
RF320, RF323
TO-5 Relays:
ER411, ER431, RF311, RF331
NOTES
1. Terminal views shown
2. Dimensions are in inches (mm)
3. Tolerances: ± .010 (±.25) unless otherwise speci ed
4. Ground pin positions are within .015 (0.38) dia. of true position
5. Ground pin head dia., 0.035 (0.89) ref: height 0.010 (0.25) ref.
6. Lead dia. 0.017 (0.43) nom.
Indicates ground pin position
Indicates glass insulated lead position
Indicates ground pin or lead position
depending on relay type
Appendix A: Ground Pin Positions
© 2008 Teledyne Relays SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE