5305 Spectrum Drive, Frederick, MD 21703-7362 TEL: 301-846-9222, 800-638-2048 Fax: 301-846-9116
web: www.aeroflex.com/weinschel email: weinschel-sales@aeroflex.com
32
SmartStep®Subsystems
Revision Date: 2/20/09
Description
Model 8210A represents a new concept in device control
applications and provides a high level interface from various
industry standard communications interfaces to the serial
Driver Interface Bus.
The Device Interface Bus (DIB) is a system for connecting
a number of relatively low-speed I/O devices to a host, pro-
viding a simple, uniform and inexpensive way to control a
variety of devices via a single port. The DIB is based on the
two-wire serial bus and several software protocol layers that
allow the Model 8210A to address up to 125 peripheral
devices with serial data rates of up to 100 KHz. The DIB
may also be used to supply DC power to the devices, result-
ing in a simple, low-cost interconnection system.
This Programmable attenuator/switch controller is available
in two models, each providing a different type of communi-
cations interface to suit user configuration requirements.
Each model contains similar capabilities, and provides
switch-selectable parameters to the interfaces’ operation.
Model 8210A
Programmable Attenuator/Switch Controller RS232\RS422/RS485
A Logical Interface for Switchable Devices!
Features
oProvides a flexible, powerful, low cost solution for bus
control of programmable step attenuators and other
switchable devices under computer control.
oDesigned to interface with Aeroflex / Weinschel’s line
of intelligent programmable attenuators and other
electromechanical devices.
oSimplifies your bench test setups and subsystem
design.
oAvailable in two standard communication interfaces:
- Model 8210A-1: GPIB/IEEE-488 (HS-488 ready)
- Model 8210A-2: RS-232, RS-422, RS-485
Applications
Applications for the 8210A range from providing control of a
single Programmable Attenuator in a bench test/lab envi-
ronment using a PC and a terminal emulator, to complex
system applications where the 8210A is employed to control
many devices to create custom/semi-custom subsystems to
reduce overall design cost. Aeroflex / Weinschel can pro-
vide a variety of custom designed driver interfaces for
various devices, such as RF switches, relays, PIN attenua-
tors, displays and other devices, as well as complete
subsystem design and integration services. Contact us with
your specialized needs.
Typical Capacity: Control a subsystem consisting of 32
individual 8-cell programmable attenuators plus 16
DPDT switches.
For additional information on the Model 8210A, visit our website @ www.aeroflex.com/AW/8210A.htm
IEEE-488
33
5305 Spectrum Drive, Frederick, MD 21703-7362 TEL: 301-846-9222, 800-638-2048 Fax: 301-846-9116
web: www.aeroflex.com/weinschel email: weinschel-sales@aeroflex.com
SmartStep®Subsystems
Revision Date: 2/20/09
DC Input Connector: 2.5mm barrel style
Requirements: +12 to +15 Vdc @ 250 mA
Driver Interface Connector: 14-pin 0.025" square post header @ 0.1" centers. Mates with
AMP 746285-2 or equivalent.
Signals : SDA serial data
SDC serial clock
VDC DC supply voltage
GND ground
VDC Output Current: 2 A maximum
Maximum Cable Length: 10 Meters (1000 pF maximum capacitance)
Data Transfer Rate: 100 KHz
Environmental Operating Temperature: 0 to +50°C
Storage Temperature: -55° to +75°C (67° to +167°F)
Humidity: 95%
Altitude: 40,000' (12,192M)
IEEE-488 Bus(1) Connector: 24-pin per IEEE-488.1
Protocols: per IEEE-488.2
Indicators: Remote, Listen
RS-232 Bus(2) Connector: 9-pin male D
Signals: TXD, RXD, RTS, CTS, DTR, GND
Baud Rates: 2400, 9600, and 19200, 38400
Data Bits: 8
Handshaking: None, RTS/CTS, XON/XOFF
Parity: None, Odd, Even
Indicators: Tx (Transmit) and Rx (Receive Active)
RS-422 Bus(3) &Connector: 9-pin male D(Model 8210-2)
RS-485 Bus(4) Signals: TXD+, TDX-, RXD+, RTX-, RTS+, RTS-, CTS+, CTS-, & signal GND
Baud Rates: 2400, 9600, and 19200, 38400
Data Bits: 8
Handshaking: None, RTS/CTS, XON/XOFF
Parity: None, Odd, Even
Indicators: Tx (Transmit) and Rx (Receive Active)
Notes:
1. GPIB/IEEE-488 model allows user-selectable addresses.
2. RS-232 can be used with standard PC serial port for short and medium distances (up to approximately 50 ft).
3. RS-422, designed for very long distance communications (4000 ft) & optimized as a single node protocol, typically with one device connected to a
single port.
4. RS-485, designed for very long distance communications (4000 ft) & optimized for multi-drop connections that can used to create a low cost network.
Specifications
SPECIFICATION DESCRIPTION
001-378 Deskmount Power Supply, +15 V
95-250 Vac, 47-63 Hz ac input
193-8013 Interconnect Cable
193-8012 Attenuator Mounting Kit: This kit
includes all hardware to allow the
user to mount one attenuator onto
the Model 8210A
Accessories:
PART NUMBER DESCRIPTION
5305 Spectrum Drive, Frederick, MD 21703-7362 TEL: 301-846-9222, 800-638-2048 Fax: 301-846-9116
web: www.aeroflex.com/weinschel email: weinschel-sales@aeroflex.com
34
SmartStep®Subsystems
Revision Date: 2/20/09
Physical Dimensions
NOTE: All dimensions are given in mm (inches) and are maximum, unless otherwise specified.
Model 8210A-2 (RS-232/RS-422/RS-485):
Model 8210A-1 (IEEE-488):