LTC4267-1
25
42671fa
For more information www.linear.com/4267-1
transformer jack on the PD since this would compromise
the 802.3af isolation safety requirements.
Figure 16 demonstrates three methods of diode ORing
external power into a PD. Option 1 inserts power before
the LTC4267-1 interface controller while options 2 and
3 bypass the LTC4267-1 interface controller section and
power the switching regulator directly.
If power is inserted before the LTC4267-1 interface con-
troller, it is necessary for the wall transformer to exceed
the LTC4267-1 UVLO turn-on requirement and include a
transient voltage suppressor (TVS) to limit the maximum
voltage to 57V. This option provides input current limit
for the transformer, provides a valid power good signal,
and simplifies power priority issues. As long as the wall
transformer applies power to the PD before the PSE, it
will take priority and the PSE will not power up the PD
because the wall power will corrupt the 25k signature. If
the PSE is already powering the PD, the wall transformer
power will be in parallel with the PSE. In this case, prior-
ity will be given to the higher supply voltage. If the wall
transformer voltage is higher, the PSE should remove the
line voltage since no current will be drawn from the PSE.
On the other hand, if the wall transformer voltage is lower,
the PSE will continue to supply power to the PD and the
wall transformer will not be used. Proper operation should
occur in either scenario.
If auxiliary power is applied directly to the LTC4267-1
switching regulator (bypassing the LTC4267-1 PD inter-
face), a different set of trade-offs arise. In the configuration
shown in option 2, the wall transformer does not need
to exceed the LTC4267-1 turn-on UVLO requirement;
however, it is necessary to include diode D9 to prevent
the transformer from applying power to the LTC4267-1
interface controller. The transformer voltage requirement
will be governed by the needs of the onboard switching
regulator. However, power priority issues require more
intervention. If the wall transformer voltage is below
the PSE voltage, then priority will be given to the PSE
power. The LTC4267-1 interface controller will draw power
from the PSE while the transformer will sit unused. This
configuration is not a problem in a PoE system. On the
other hand, if the wall transformer voltage is higher than
the PSE voltage, the LTC4267-1 switching regulator will
draw power from the transformer. In this situation, it is
necessary to address the issue of power cycling that may
occur if a PSE is present. The PSE will detect the PD and
apply power. If the switcher is being powered by the wall
transformer, then the PD will not meet the minimum load
requirement and the PSE will subsequently remove power.
The PSE will again detect the PD and power cycling will
start. With a transformer voltage above the PSE voltage,
it is necessary to either disable the signature, as shown
in option 2, or install a minimum load on the output of the
LTC4267-1 interface to prevent power cycling.
The third option also applies power directly to the
LTC4267-1 switching regulator, bypassing the LTC4267-1
interface controller and omitting diode D9. With the
diode omitted, the transformer voltage is applied to the
LTC4267-1 interface controller in addition to the switching
regulator. For this reason, it is necessary to ensure that
the transformer maintain the voltage between 38V and 57V
to keep the LTC4267-1 interface controller in its normal
operating range. The third option has the advantage of
automatically disabling the 25k signature resistor when
the external voltage exceeds the PSE voltage.
Power-Up Sequencing the LTC4267-1
The LTC4267-1 consists of two functional cells, the PD
interface and the switching regulator, and the power up
sequencing of these two cells must be carefully considered.
The PD designer should ensure that the switching regulator
does not begin operation until the interface has completed
charging up the load capacitor. This will ensure that the
switcher load current does not compete with the load
capacitor charging current provided by the PD interface
current limit circuit. Overlooking this consideration may
result in slow power supply ramp up, power-up oscillation,
and possibly thermal shutdown.
The LTC4267-1 includes a power good signal in the PD
interface that can be used to indicate to the switching regu-
lator that the load capacitor is fully charged and ready to
handle the switcher load. Figure 7 shows two examples of
ways the PWRGD signal can be used to control the switch-
ing regulator. The first example employs an N-channel
MOSFET to drive the ITH/RUN port below the shutdown
threshold (typically 0.28V). The second example drives