2536 Amphenol FCC.V6 9/21/01 10:48 AM Page cov3
Choosing the Right Capacitance for Your Filter Connector
Amphenol®
Amphenol Canada Corp. a subsidiary of Amphenol Corporation,
is an international leader in the manufacture of Filtered
Connectors and Specialty Interconnect Devices, and has been
pioneering EMI and EMP technologies fo r mo r e than 40 years.
Located in Toronto, Canada, our ISO 9001 certified facility
employs approximately 400 people. Our activities are dedicated
to the design, development and manufacture of EMI/EMP filter
connector products which are used in Commercial, Industrial,
Communications, Military and Aerospace applications world-
wide. Our expertise in understanding and supporting our cus-
tomers’ filter interconnect needs has earned Amphenol Canada a
reputation of quality and excellence among the world’s leading
users of electronic components.
Nominal Insertion Loss values described in this catalog are
based on the Mil-STD-220 test method - a 50 ohm balanced load
and source impedance. Different systems will differ from this and
hence, the filter connector may perform differently.
The final decision will be determined from actual EMI/RFI
testing of the equipment in question.
(1)Determine the highest frequency that the filter connector
needs to pass unaffected.
(2)Which frequencies are causing trouble, either with
emissions or with immunity to interference?
(3)Scan the Insertion Loss charts on page 2 to select a filter
which provides little or no insertion loss (filtering) at the
frequency determined from step 1, yet gives the greatest
possible insertion loss at the frequencies determined in step 2.
A filtered connector is the combination of filter elements in a
connector, forming one neat, compact interconnect device that
can filter unwanted EMI. The most popular configuration is when
capacitors are mounted inside the connector between each of
the contacts and the connector ground shell.
What is a Filtered Connector?
Benefits
Better EMI Control – With minimized lead inductances and
short, direct paths to ground of the filter, performance
will typically out perform the same filter components on
a P.C.B. by a factor of three to one.
PCB Space Savings – Incorporating filter elements into the
connector, enables simplification of the required filter
schematic for the necessary performance plus a savings
of 2-4 square inches.
Cost Savings – Filter elements, such as inductors and capaci-
tors, must no longer be purchased, stocked, assembled
or tested. Fewer components means greater reliability at
lower cost.
Easy EMI/RFI Upgrade – These compact filtered connectors
fit standard non-filtered connector footprints. For
improved EMC performance, simply replace the existing
connector with a filtered connector.
EMC Compliance & Immunity – EMI that is generated
from the electronic device, radiated or conducted, will
be re-directed to chassis ground through the connector
shell. This same device will also protect the system from
external EMI/RFI noise (such as radio transmitters, ESD,
or natural phenomena such as lightning) in the same way.
The Company
2536 Amphenol FCC.V6 9/21/01 10:48 AM Page cov4
Contents
1
Amphenol®Canada Corp. Telephone: (416) 754-5656 Fax: (416) 754-8668 E-mail: sales@amphenolcanada.com
RF Series
D–Sub Series
Capacitively Decoupled RF Connectors 23-35
Electrical Data, Insertion Loss Performance 2
Mechanical and Environmental Data 3
Filtered Micro-Ribbon Connectors: How To Orde r 17-2 2
Electrical Data, Insertion Loss Performance 2
Mechanical and Environmental Data 3
Filtered Stacked D-Sub Connectors 4
Filtered D-Sub Connectors: How To Order 5-10
Filtered Combo D-Sub Connectors 11-16
Micro–Ribbon Series
FCC17 Series
FCC57 Series
456 Series
Modular Jacks
Filtered & Shielded -
See Modular Jack Catalogue
FRJ/FRJA Series
2536 Amphenol FCC.V6 9/21/01 10:48 AM Page 1
FCC17 &FCC57 Series
2Amphenol®Canada Corp. Telephone: (416) 754-5656 Fax: (416) 754-8668 E-mail: sales@amphenolcanada.com
ELECTRICAL DATA
Contact Resistance: 15 milliohms maximum per MIL-STD-1344 Method 3002
Insulation Resistance: 3000 megohms minimum per MIL-STD-1344 Method 3003.1
Current Rating: 5 Amps DC maximum
2 Amps RF filtering maximum
FCC17 Combo: 20-40 Amps
Filter Performance:
Filter Capacitance (pF) 50 180 330 470 820 1000 1200 2200 5600 47000
@25°C, 1 kHz, 1.0 VRMS ± 15% ± 15% ± 15% ± 15% ± 15% ± 15% ± 15% ± 15% ± 20% ± 20%
Dielectric Material: NPO or X7R
Insertion Loss (dB)
(per MIL-STD-220 @ .5 MHz 315
25°C) 1 MHz 1520
5 MHz 1 1 1 1 5 11 27
10 MHz 1 2 3 3 4 8 16 32
50 MHz 4 7 11 16 16 17 23 32 32
100 MHz 2 12 15 22 30 30 30 32 32 32
200 MHz 12 27 28 30 32 32 32 32 32 32
1000 MHz 32 32 32 32 32 32 32 32 32 32
Working Voltage (VDC) 300 300 300 300 200 200 200 200 200 50
DWV (VDC) * 600 600 600 600 600 600 600 600 600 150
40
30
20
10
0
0.1 1.0 10 100 1000
Frequency (MHz)
50 pF - 470 pF
Insertion Loss (dB)
40
30
20
10
0
0.1 1.0 10 100 1000
Frequency (MHz)
820 pF - 1000 pF
Insertion Loss (dB)
40
30
20
10
0
0.1 1.0 10 100 1000
Frequency (MHz)
1,200 pF - 2,200 pF
Insertion Loss (dB)
40
30
20
10
0
0.1 1.0 10 100 1000
Frequency (MHz)
5,600 pF - 47,000 pF
Insertion Loss (dB)
Typical Insertion Loss Performance (dB)(Per MIL-STD-220, no load)
NOTE: A larger range of capacitors available - consult factory.
* FCC57 connectors can be specified to meet the requirements of FCC Docket 20780, Part 68, Subpart F (1000 VAC for one minute. Consult factory for details).
FCC17 and FCC57 connectors can withstand a transient voltage spike of 700 V with a rise time of 1 µsec (500 V for 47000 pF).
FCC17 and FCC57 connectors can be specified to meet higher DWV and transient voltage requirement (consult factory).
2536 Amphenol FCC.V6 9/21/01 10:48 AM Page 2
FCC17 &FCC57 Series
3
Amphenol®Canada Corp. Telephone: (416) 754-5656 Fax: (416) 754-8668 E-mail: sales@amphenolcanada.com
MECHANICAL DATA
FCC17 Series Construction
FCC17 & FCC57 Mechanical & Environmental Data
Stamped steel
shell plated
per MIL-T-10727
High strength
thermoplastic
insert
Gold plated
phosphor
bronze contact
with integral
contact spring
Mounting hole
(threaded or
through hole)
Board lock
device
Low impedance
chip capacitor
MATERIALS
FCC17 FCC57
Shell Stamped Steel; Shell Stamped Steel,
Tin Plated Zinc or Aluminum
Diecast; Tin Plated
Contacts Phosphor Bronze; Contacts Phosphor Bronze;
15µ inches 30µ inches
[0.38 microns] [0.76 microns]
Au over Ni Au over Ni
Optional 50µ inches Optional 50µ inches
[1.27 microns] [1.27 microns]
Au available Au available
FCC17 Combo
Copper Alloy
30µ inches
[0.76 microns]
Au over Ni
Inserts High Strength Inserts High Strength
Thermoplastic. Thermoplastic.
Complies with UL Complies with UL
flammability flammability
requirements of requirements of
94V-O per UL-STD-94. 94V-O per UL-STD-94.
ENVIRONMENTAL
FCC17 & FCC57
OPERATING TEMPERATURE • -40°C to +85°C
TEMPERATURE CYCLING • To MIL-STD-1344,
Method 1003, Test Cond. A
HUMIDITY • To MIL-STD-1344,
Method 1002, Type I,
Test Condition C
VIBRATION • To MIL-STD-1344,
Method 2005, Test Cond. III
DURABILITY • 200 Cycles Minimum,
to MIL-STD-1344,
Method 2016
UL File # E135615
CSA File # LR68598
2536 Amphenol FCC.V6 9/21/01 10:48 AM Page 3
FCC17 Series
4Amphenol®Canada Corp. Telephone: (416) 754-5656 Fax: (416) 754-8668 E-mail: sales@amphenolcanada.com
FILTERED STACKED D-SUB CONNECTORS
Ordering Information – Stacked D-Sub
Dimensions
Connector size A B C
9 / 9 1.213 [30.81] .984 [24.99] .432 [10.97]
15 / 15 1.541 [39.14] 1.312 [33.32] .756 [19.20]
25 / 25 2.088 [53.04] 1.852 [47.04] 1.304 [33.12]
37 / 37 2.729 [69.32] 2.500 [63.50] 1.956 [49.68]
Consult factory for alternative arrangements
PCB LAYOUT
FCC17 –2BPBS–455X
MODIFIER X
0: Standard Product
x: Special or Custom Versions
LOWER CONNECTOR FILTER CAPACITANCE 5
same as Upper Connector Filter
Capacitance Designation
UPPER CONNECTOR FILTER CAPACITANCE 5
D: 50 pF 5: 1,000 pF
0: 180 pF E: 2,200 pF
F: 330 pF 7: 1,200 pf
1: 470 pF 9: 5,600 pF
4: 820 pF 8: 47,000 pF
SERIES DESIGNATION
2VERTICAL MOUNTING DIMENSION
BETWEEN CONNECTORS
1 = .625" [15.88 mm]
2 = .750" [19.05 mm]
BP UPPER CONNECTOR CONFIGURATION
(Size and Style)
EP: 9 pin BP: 25 pin
ES: 9 socket BS: 25 socket
AP: 15 pin CP: 37 pin
AS: 15 socket CS: 37 socket
BS LOWER CONNECTOR CONFIGURATION
(Size and Style) same as Upper Connector
Configuration
4MOUNTING
2: .120" [3.05 mm] Diameter Through Hole
on Flanges
4: 4-40 Threaded Inserts on Flanges
E: 4-40 Hex Jack Sockets (supplied loose)
FCC17
* For Additional Mounting Options and
Filter Capacitance - Consult Factory
4–40 THREADS
OR .120” DIAMETER
THROUGH HOLE
2536 Amphenol FCC.V6 9/21/01 10:49 AM Page 4
FCC17 Series
5
Amphenol®Canada Corp. Telephone: (416) 754-5656 Fax: (416) 754-8668 E-mail: sales@amphenolcanada.com
FILTERED D-SUB CONNECTORS
These products are protected by U.S. Patent # 4500159
Ordering Information – D-Sub
Specifications
Filter Characteristics: See Page 2
Electrical Data: See Page 2
Material and Finishes: See Page 3
Environmental Data: See Page 3
UL File # : E135615
CSA File # : LR68598
FCC17 –B25 S C –44 0 G
SERIES DESIGNATION
SIZE
E09
A15
B25
C37
SCONNECTOR TYPE
A - Adapter
P - Pin
S - Socket
CTERMINATION TYPE
A - Right Angle PC Tail, .318" [8.08 mm] Footprint
B - Right Angle PC Tail, .405" [10.29 mm] Footprint
C - Right Angle PC Tail, .590" [14.99 mm] Footprint
D - Pin/Socket Adapter
E - Vertical Mount PC Tail
M -Solder Cup
N - Vertical Mount PC Tail - Long Body
4MOUNTING OPTIONS*
A: 4-40 Threaded PC Tail Standoffs
with Boardlock, Vertical Mount Only
E: 4-40 Hex Jack Sockets (supplied loose)
F: 4-40 Round Fixed Jack Sockets
2: .120 [3.05 mm] diameter Through hole
3: Self-Locking 4-40 Threaded Inserts
4: 4-40 Threaded Inserts (Standard)
5: 4-40 Threaded Stand-Offs, Vertical Mount
6: M3 Threaded inserts
FCC17
SPECIALS G
No Digit: Standard 15µ inches gold
G: 50 micro inches gold
K: 30 micro inches gold
L: Standard Connector with added
ferrite block
MODIFIER 0
0 = Standard Product (Boardlocks
on Right Angle D-Subs)
B = Metal Mounting Brackets,
for Right Angle D-Subs
D = .315” to Boardlock for .590” footprint
E = Plastic Bracket - No Boardlock
F = No Boardlock, No plastic or metal
Bracket - Alignment Strip Only
X = Specials or Custom Versions
FILTER CAPACITANCE [pF]* 4
D: 50 pF
B: 100 pF
0: 180 pF
F: 330 pF
1: 470 pF
4: 820 pF
5: 1,000 pF
7: 1,200 pF
E: 2,200 pF
9: 5,600 pF
8: 47,000 pF
* For Additional Mounting Options and
Filter Capacitance - Consult Factory
B25
2536 Amphenol FCC.V6 9/21/01 10:49 AM Page 5
FCC17 Series
6Amphenol®Canada Corp. Telephone: (416) 754-5656 Fax: (416) 754-8668 E-mail: sales@amphenolcanada.com
FILTERED D-SUB CONNECTORS
SocketPin
Mounting Dimensions
All Dimensions in Inches (mm)
Shell Standard A B C D
Size Number of (for pin (for socket
Contacts connector) connector)
E 9 1.213 [30.81] .984 [24.99] .666 [16.92] .643 [16.33]
A 15 1.541 [39.14] 1.312 [33.32] .994 [25.25] .971 [24.66]
B 25 2.088 [53.04] 1.852 [47.04] 1.534 [38.96] 1.511 [38.38]
C 37 2.729 [69.32] 2.500 [63.50] 2.182 [55.42] 2.159 [54.84]
FRONT VIEW END VIEWFRONT VIEW END VIEW
FRONT MOUNTING CUT-OUT REAR MOUNTING CUT-OUT
Size Mounting A B C
9Front .875 [22.23] .984 [24.99] .512 [13.00]
Rear .807 [20.50] .984 [24.99] .449 [11.40]
15 Front 1.200 [30.48] 1.312 [33.32] .512 [13.00]
Rear 1.134 [28.80] 1.312 [33.32] .449 [11.40]
25 Front 1.744 [44.30] 1.852 [47.04] .512 [13.00]
Rear 1.673 [42.49] 1.852 [47.04] .449 [11.40]
37 Front 2.389 [60.68] 2.500 [63.50] .512 [13.00]
Rear 2.326 [59.08] 2.500 [63.50] .449 [11.40]
2536 Amphenol FCC.V6 9/21/01 10:49 AM Page 6
FCC17 Series
7
Amphenol®Canada Corp. Telephone: (416) 754-5656 Fax: (416) 754-8668 E-mail: sales@amphenolcanada.com
FILTERED D-SUB CONNECTORS
Vertical Mount
Right Angle, with Boardlocks & Plastic Mounting Brackets
Right Angle, with Metal Mounting Brackets
.318" FOOTPRINT
.405" FOOTPRINT
.405" FOOTPRINT
.590" FOOTPRINT
.590" FOOTPRINT
.318" FOOTPRINT
Termination Type E Termination Type N
Termination Type A
with Modifier option O Termination Type B
with Modifier option O Termination Type C
with Modifier option O
Termination Type A
with Modifier option B Termination Type B
with Modifier option B Termination Type C
with Modifier option B
2536 Amphenol FCC.V6 9/21/01 10:49 AM Page 7
FCC17 Series
8Amphenol®Canada Corp. Telephone: (416) 754-5656 Fax: (416) 754-8668 E-mail: sales@amphenolcanada.com
FILTERED D-SUB CONNECTORS
Solder Cup Termination
Termination type M
Pin-to-Socket Adapter
Termination type D
Mounting Options
Through Hole with Mounting Post
4-40 Threaded Inserts
Part No. Example
FCC17-B25AD-2x0
FCC17-B25AD-4x0
x = To complete the P/N, see page 5 to assign Filter Capacitance Code.
For electrical and mechanical specifications, see pages 2 and 3.
SIDE VIEW END VIEW
SOLDER CUP DETAIL
(ACCEPTS UP TO 20 AWG WIRE)
2536 Amphenol FCC.V6 9/21/01 10:49 AM Page 8
FCC17 Series
9
Amphenol®Canada Corp. Telephone: (416) 754-5656 Fax: (416) 754-8668 E-mail: sales@amphenolcanada.com
FILTERED D-SUB CONNECTORS
Mounting Options (on Flange)
Bracket Options & Specials
-Axx
4-40 Threaded Standoffs with
Boardlocks (Vertical Mount only)
Mounting code A
Shown for Vertical Mount Connectors. Codes 2, 3, 4, 6, E and F also available on right angle connectors.
-Exx
4-40 Hex Jack Sockets (supplied loose)
Mounting code E
-Fxx
4-40 Round fixed Jack Sockets
Mounting code F
-5xx
4-40 Threaded Standoff (vertical mount only)
Mounting code 5
-xxD-xxE-xxF
.315” to Boardlock
for .590” Footprint only
Modifier option D
FERRITE
Consult Factory for details
Plastic bracket only
Modifier option E Alignment Strip Only
No bracket or boardlocks
Modifier option F
-2xx
.120" (3.05 mm) diameter thru hole
Mounting code 2
-3xx, 4xx and 6xx
4-40 Threaded Inserts - Self locking
4-40 Threaded inserts (standard)
M3 threaded inserts
Mounting codes 3, 4 and 6
Termination “A”
Type Dimension
A.318 (8.08)
B.405 (10.29)
C.590 (14.99)
2536 Amphenol FCC.V6 9/21/01 10:49 AM Page 9
FCC17 Series
10 Amphenol®Canada Corp. Telephone: (416) 754-5656 Fax: (416) 754-8668 E-mail: sales@amphenolcanada.com
FILTERED D-SUB CONNECTORS
PCB Layout
25 SIZE
37 SIZE
15 SIZE
9 SIZE
Standard PCB layout PCB layout for
.590" footprint with Modifier
Options B or D only
Standard PCB layout PCB layout for
.590" footprint with Modifier
Options B or D only
Standard PCB layout PCB layout for
.590" footprint with Modifier
Options B or D only
Standard PCB layout PCB layout for
.590" footprint with Modifier
Options B or D only
2536 Amphenol FCC.V6 9/21/01 10:49 AM Page 10
FCC17 –A
3W3
PM–450G
SERIES DESIGNATION
ASHELL SIZE
A, B, C, D, E
3W3 ARRANGEMENT
See page 12
PCONNECTOR TYPE
A = Adapter
P = Pin
S = Socket
MTERMINATION TYPE
D = Pin/Socket Adapter
E = Power PC Tail – 40A - .126" Dia., .175" Lg.
K = Power Solder Cup – 10A – Wire Size 16
L = Power Solder Cup – 20A – Wire Size 12
M =Power Solder Cup – 40A – Wire Size 8
R = Power Press Fit – 20A - .145" Lg. - .126" Dia. Hole
4MOUNTING OPTIONS 4
2 = .120" dia. mounting holes
3 = 4-40 Threads Self locking
4 = 4-40 Threads
5 = 4-40 Standoffs - PC tail only
6 = M3 Threads
E = 4-40 Hex Jack Sockets [supplied loose]
PLATING OPTION G
Blank = Standard 30 microinches gold
G = 50 microinches gold
MODIFIER 00
0 = Standard
X = Specials or Custom versions
[Consult Factory]
FILTER CAPACITANCE (pF) 5
D: 50 pF
B: 100 pF
O: 180 pF
F: 330 pF
I: 470 pF
4: 820 pF
5: 1000 pF
7: 1200 pF
E: 2200 pF
9: 5600 pF
8: 47000 pF
FCC17
FCC17 Series
11
Amphenol®Canada Corp. Telephone: (416) 754-5656 Fax: (416) 754-8668 E-mail: sales@amphenolcanada.com
COMBO D-SUB FILTER CONNECTORS
Filter Characteristics: See Page 2
Electrical Data: See Page 2
Material and Finishes: See Page 3
Environmental Data: See Page 3
UL File # : E135615
CSA File # : LR68598
Ordering Information – Combo D-Sub
Specifications
These products are protected by U.S. Patent # 4500159
* For Additional Mounting Options and
Filter Capacitance - Consult Factory
2536 Amphenol FCC.V6 9/21/01 10:49 AM Page 11
FCC17 Series
12 Amphenol®Canada Corp. Telephone: (416) 754-5656 Fax: (416) 754-8668 E-mail: sales@amphenolcanada.com
COMBO D-SUB FILTER CONNECTORS
Insert Arrangements - Male Front View
Consult Factory for Additional Arrangements and Polarization
Shell Size E
Arrangement 2W2
No. of Signal Contacts 0
No. of Power Contacts 2
Shell Size A
Arrangement 3W3
No. of Signal Contacts 0
No. of Power Contacts 3
Shell Size B
Arrangement 5W5
No. of Signal Contacts 0
No. of Power Contacts 5
Shell Size B
Arrangement 9W4
No. of Signal Contacts 5
No. of Power Contacts 4
Shell Size B
Arrangement 13W3
No. of Signal Contacts 10
No. of Power Contacts 3
Shell Size B
Arrangement 17W2
No. of Signal Contacts 15
No. of Power Contacts 2
Shell Size C
Arrangement 27W2
No. of Signal Contacts 25
No. of Power Contacts 2
Shell Size C
Arrangement 8W8
No. of Signal Contacts 0
No. of Power Contacts 8
Shell Size C
Arrangement 21WA4
No. of Signal Contacts 17
No. of Power Contacts 4
Consult factory
for availability Consult factory
for availability Consult factory
for availability
Consult factory
for availability
Consult factory
for availability
Consult factory
for availability
Consult factory
for availability Keyed Version
also available
Consult factory
for availability
Keyed Version
also available
Consult factory
for availability
2536 Amphenol FCC.V6 9/21/01 10:50 AM Page 12
FCC17 Series
13
Amphenol®Canada Corp. Telephone: (416) 754-5656 Fax: (416) 754-8668 E-mail: sales@amphenolcanada.com
COMBO D-SUB FILTER CONNECTORS
Consult Factory - Shell Size D
Pin Socket
Mounting Dimensions
Size Mounting A B C
EFront .875 [22.23] .984 [24.99] .512 [13.00]
Rear .807 [20.50] .984 [24.99] .449 [11.40]
AFront 1.200 [30.48] 1.312 [33.32] .512 [13.00]
Rear 1.134 [28.80] 1.312 [33.32] .449 [11.40]
BFront 1.744 [44.30] 1.852 [47.04] .512 [13.00]
Rear 1.673 [42.49] 1.852 [47.04] .449 [11.40]
CFront 2.389 [60.68] 2.500 [63.50] .512 [13.00]
Rear 2.326 [59.08] 2.500 [63.50] .449 [11.40]
All Dimensions in Inches (mm)
Shell A B C D
Size (for pin (for socket
conn. only) conn. only)
E 1.213 [30.81] .984 [24.99] .666 [16.92] .643 [16.33]
A 1.541 [39.14] 1.312 [33.32] .994 [25.25] .971 [24.66]
B 2.088 [53.04] 1.852 [47.04] 1.534 [38.96] 1.511 [38.38]
C 2.729 [69.32] 2.500 [63.50] 2.182 [55.42] 2.159 [54.84]
FRONT VIEW END VIEWFRONT VIEW END VIEW
STANDARD CUT-OUT
(FOR FRONT MOUNTING) OPTIONAL CUT-OUT
(FOR REAR MOUNTING)
2536 Amphenol FCC.V6 9/21/01 10:50 AM Page 13
FCC17 Series
14 Amphenol®Canada Corp. Telephone: (416) 754-5656 Fax: (416) 754-8668 E-mail: sales@amphenolcanada.com
COMBO D-SUB FILTER CONNECTORS
Straight PCB Press Fit
Solder Cup Adapter – Pin/Socket
Termination type E
Termination types: K, L, M Termination type: D
Termination type R
2536 Amphenol FCC.V6 9/21/01 10:50 AM Page 14
FCC17 Series
15
Amphenol®Canada Corp. Telephone: (416) 754-5656 Fax: (416) 754-8668 E-mail: sales@amphenolcanada.com
COMBO D-SUB FILTER CONNECTORS
PCB Layout - Straight PCB & Press Fit
E
2W2 A
3W3
B
5W5 B
9W4
Consult Factory
B
13W3
Consult Factory
B
17W2
Consult Factory
2536 Amphenol FCC.V6 9/21/01 10:50 AM Page 15
FCC17 Series
16 Amphenol®Canada Corp. Telephone: (416) 754-5656 Fax: (416) 754-8668 E-mail: sales@amphenolcanada.com
COMBO D-SUB FILTER CONNECTORS
PCB Layout - Straight PCB & Press Fit
C
8W8
C
21WA4
Consult Factory
C
27W2
Consult Factory
2536 Amphenol FCC.V6 9/21/01 10:50 AM Page 16
FCC57 –21502–410HV
SERIES DESIGNATION
2CONNECTOR TYPE
0 = Adapter
1 = Plug (Available in 50 size only)
2 = Receptacle
1TERMINATION TYPE
0 = Solder Cup
1 = Straight PCB
2 = Right Angle PCB
5 = Straight PCB Press-Fit
9 = Adapter Plug/Receptacle
50 NUMBER OF CONTACTS
36, 50, 64
2HOUSING STYLE
0 = Standard
2 = Receptacle without Spring Latches
or Spring Holder
4 MOUNTING OPTIONS4
2 = .120" [3.05 mm] or .125" diameter hole
in flange [not standard for Adapters]
4 = 4-40 Threaded Inserts
5 = 4-40 Threaded Standoff
6 = M3 Threaded Inserts
A = 4-40 Threaded Inserts with boardlocks
E = 4-40 Jack Sockets [Supplied Loose]
VOLTAGE HV
No digits = Standard
HV - High Voltage [1000V AC per part 68]
MODIFIER 0
0 = Standard
X = Special or Custom Versions
FILTER CAPACITANCE (pF) 1
D: 50 pF
B: 100 pF
O: 180 pF
F: 330 pF
I: 470 pF
4: 820 pF
5: 1000 pF
7: 1200 pF
E: 2200 pF
9: 5600 pF
8: 47000pF
FCC57
FCC57 Series
17
Amphenol®Canada Corp. Telephone: (416) 754-5656 Fax: (416) 754-8668 E-mail: sales@amphenolcanada.com
FILTERED MICRO-RIBBON CONNECTORS
Filter Characteristics: See Page 2
Electrical Data: See Page 2
Material and Finishes: See Page 3
Environmental Data: See Page 3
UL File # : E135615
CSA File # : LR68598
Ordering Information
High voltage capacitors available (contact factory)
These products are protected by U.S. Patent # 4500159
Specifications
2536 Amphenol FCC.V6 9/21/01 10:50 AM Page 17
FCC57 Series
18 Amphenol®Canada Corp. Telephone: (416) 754-5656 Fax: (416) 754-8668 E-mail: sales@amphenolcanada.com
FILTERED MICRO-RIBBON CONNECTORS
Receptacle - 36, 50, 64 Size
Panel Mounting Dimensions - 36 / 50 / 64 size
TOP VIEW
RECEPTACLE
REAR MOUNT
[.050 MAX. PANEL THICKNESS]
Connector
Size A B
36 2.637 [66.98] 2.350 [59.69
50 3.260 [82.80] 2.947 [74.85]
64 3.835 [97.41] 3.542 [89.97]
Connector
Size A B B
36 2.043 [71.05] 2.350 [59.69] 2.450 [85.20]
50 2.656 [92.36] 2.947 [74.85] 3.062 [106.48]
64 3.251 [113.06] 3.542 [89.97] 3.657 [127.18]
Dimensions are different for DieCast Shells
Consult Factory for details
2536 Amphenol FCC.V6 9/21/01 10:50 AM Page 18
FCC57 Series 36 Size
19
Amphenol®Canada Corp. Telephone: (416) 754-5656 Fax: (416) 754-8668 E-mail: sales@amphenolcanada.com
FILTERED MICRO-RIBBON CONNECTORS
Receptacle
Adapter PLUG/RECEPTACLE (FCC57 - 09360 - 1 X 0)
STRAIGHT PCB (FCC57 - 21360 - 1 x0)
STRAIGHT PRESS-FIT (FCC57 - 25360 - 1 x0)
RIGHT ANGLE PCB (FCC57 - 22360 - 1 x0)
PCB LAYOUT
PCB LAYOUT
PCB LAYOUT
2536 Amphenol FCC.V6 9/21/01 10:51 AM Page 19
FCC57 Series 50 Size
20 Amphenol®Canada Corp. Telephone: (416) 754-5656 Fax: (416) 754-8668 E-mail: sales@amphenolcanada.com
FILTERED MICRO-RIBBON CONNECTORS
Receptacle
STRAIGHT PCB (FCC57 - 21500 - x x 0)
STRAIGHT PRESS-FIT (FCC57 - 25500 - x x 0)
RIGHT ANGLE PCB (FCC57 - 22500 - x x 0)
SOLDER CUP (FCC57 - 20500 - x x 0)
PCB LAYOUT
PCB LAYOUT
PCB LAYOUT
2536 Amphenol FCC.V6 9/21/01 10:51 AM Page 20
FCC57 Series 50 Size
21
Amphenol®Canada Corp. Telephone: (416) 754-5656 Fax: (416) 754-8668 E-mail: sales@amphenolcanada.com
FILTERED MICRO-RIBBON CONNECTORS
Plug
Adapter PLUG/RECEPTACLE (FCC57 - 09500 - x x 0)
STRAIGHT PCB (FCC57 - 11500 - x x 0)
SOLDER CUP (FCC57 - 10500 - x x 0)
TOP VIEW
PLUG
PCB LAYOUT
2536 Amphenol FCC.V6 9/21/01 10:51 AM Page 21
FCC57 Series 64 Size
22 Amphenol®Canada Corp. Telephone: (416) 754-5656 Fax: (416) 754-8668 E-mail: sales@amphenolcanada.com
FILTERED MICRO-RIBBON CONNECTORS
Receptacle
STRAIGHT PCB (FCC57 - 21640 - x0)
STRAIGHT PRESS-FIT (FCC57 - 25640 - x x 0)
RIGHT ANGLE PCB (FCC57 - 22640 - x x 0)
ADAPTER* (FCC57 - 09640 - x x 0)
PCB LAYOUT
PCB LAYOUT
PCB LAYOUT
*Consult Factory
2536 Amphenol FCC.V6 9/21/01 10:51 AM Page 22
456 Series
23
Amphenol®Canada Corp. Telephone: (416) 754-5656 Fax: (416) 754-8668 E-mail: sales@amphenolcanada.com
CAPACITIVELY DECOUPLED RF CONNECTORS
456 Series Construction
These products are protected by U.S.Patent # 4,772,221.
Mechanical Data:
Shell: Zinc Diecast or Brass; Nickel plated
Insulator Body: Thermoplastic
Contact Insulator: Nylon or Teflon
Center Contact: Phosphor Bronze or Berylium Copper;
Gold plated (456-107S is silver plated)
UL File # : E135615
CSA File # : LR68598
Filter Performance:
Capacitance 10,000 pF
Working Voltage 200 VDC (500AC Rear Mt)
DWV 600 VDC (1000VDC for Rear Mt)
Filter Insertion Loss (dB) 1 MHz 4
(per MIL-STD-220 5 MHz 16
@ 25°C and 10 MHz 18
no load) 30 MHz 25
50 MHz 30
1000 MHz 30
* OTHER CAPACITANCE VALUES ARE AVAILABLE. CONSULT THE FACTORY FOR
DETAILS.
Capacitor
Retention Ring
Chip Capacitor
and / or Spark
Gap Arrestor
Boardlock
Device
Insulator Body
Grounding
Device
Contact
Insulator
Center Contact
Shell
Amphenol’s 456 Series of RF connectors provides capacitive decoupling
between the connector body and the mounting panel. EMI on the coaxial
shield is shunted to the chassis ground through capacitors, while not
affecting the DC and power supply frequencies. This reduces ground loop
problems and provides a mechanism to harmlessly dissipate ESD to
chassis ground.
The RF parameters of these connectors are the same as their non-filtered
counterparts. Filtering does not affect the signal contact, but only the
shell-to-ground connection. Capacitively decoupled RF connectors are
intermateable and inter-changeable with standard non-filtered versions.
Specifications
2536 Amphenol FCC.V6 9/21/01 10:51 AM Page 23
456 Series
24 Amphenol®Canada Corp. Telephone: (416) 754-5656 Fax: (416) 754-8668 E-mail: sales@amphenolcanada.com
CAPACITIVELY DECOUPLED RF CONNECTORS
Rear Mount BNC, Right Angle, PCB
Rear Mount BNC, Crimp, Cable Size RG179
Vertical Mount BNC, Press-Fit
Type 50 Ω75 Ω
Filtered 456-117 456-717
Filtered (10,000pF),
1000V Spark Gap 456-117S 456-717S
Filtered (10,000pF),
1000V Spark Gap,
1 M ΩResistor 456-117F 456-717F
Grounded 456-117G 456-717G
Non-Filtered.
Panel Insulated
(no ground spring) 456-117NF 456-717NF
Type 50 Ω75 Ω
Filtered 456-208 456-218
Grounded 456-208G 456-218G
Note: Also available with Spark gap and / or resistor
* Other Cable Sizes Available. Consult Factory.
Board
Type 50 Ω75 ΩThickness “A”
Filtered – –456-107A .125 (3.18) .170 (4.32)
Non-Filtered – –456-107ANF .125 (3.18) .170 (4.32)
Filtered – –456-107B .200 (5.08) .255 (6.48)
Non-Filtered – –456-107BNF .200 (5.08) .255 (6.48)
– – Consult Factory for Part Number
PCB LAYOUT
(COMPONENT SIDE OF BOARD)
RECOMMENDED
PANEL CUT-OUT
RECOMMENDED
PANEL CUT-OUT
PCB LAYOUT
(COMPONENT SIDE OF BOARD)
2536 Amphenol FCC.V6 9/21/01 10:51 AM Page 24
456 Series
25
Amphenol®Canada Corp. Telephone: (416) 754-5656 Fax: (416) 754-8668 E-mail: sales@amphenolcanada.com
CAPACITIVELY DECOUPLED RF CONNECTORS
Front Mount BNC, Right Angle PCB
Front Mount BNC, Solder-Cup
Jack-to-Jack Adapter
Type 50 Ω75 Ω
BNC: Filtered 456-915 456-917
Twin BNC: Filtered 456-920
Type 50 Ω75 Ω
Filtered – –456-107
– – Consult factory for part number
Front Mount BNC packaging consists of connector, insulating
washer, filter ring, lock washer and hex nut.
TNC Bulkhead Jack, Crimp (RG58/U Cable)
Type 50 Ω75 Ω
Filtered 456-102 – –
– – Consult factory for part number
Packaging consists of connector, mounting hardware, panel
insulator, crimp ferrule and heat shrink tubing.
Type 50 Ω75 Ω
Filtered 456-107SG 456-107TG
456-107S has silver plated contact (50 Ω).
* Overall part length
1.180 (29.97) for 456-107S
1.245 (31.62) for 456-107SG & 456-107TG.
Front Mount BNC packaging consists of connector, insulating
washer, filter ring, ground washer and hex nut.
RECOMMENDED
PANEL CUT OUT
RECOMMENDED
PANEL CUT OUT
RECOMMENDED
PANEL CUT OUT
RECOMMENDED
PANEL CUT OUT
*
2536 Amphenol FCC.V6 9/21/01 10:52 AM Page 25
DATA /TELECOM PRODUCTS
20 Melford Drive
Scarborough, Ontario
Canada M1B 2X6
Telephone 416 754-5656
Facsimile 416 754-8668
©Amphenol Canada Corp.
Specifications subject to change without notice
Printed in Canada CATALOGUE NR. ADT 0001/01-06
Design: Macrae Design Inc.
Amphenol Catalogues
2536 Amphenol FCC.V6 9/21/01 10:48 AM Page cov2
