Order this document by MCR22-2/D SEMICONDUCTOR TECHNICAL DATA . . . designed and tested for repetitive peak operation required for CD ignition, fuel ignitors, flash circuits, motor controls and low-power switching applications. * * * * 150 Amperes for 2 s Safe Area High dv/dt Very Low Forward "On" Voltage at High Current Low-Cost TO-226AA (TO-92) SCRs 1.5 AMPERES RMS 50 thru 600 VOLTS G A K K G CASE 29-04 (TO-226AA) STYLE 10 A MAXIMUM RATINGS (TJ = 25C unless otherwise noted.) Rating Symbol Peak Repetitive Forward and Reverse Blocking Voltage (RGK = IK, TJ = 25 to 125C) Value VDRM, VRRM MCR22-2 MCR22-3 MCR22-4 MCR22-6 MCR22-8 On-State Current RMS (All Conduction Angles) Peak Non-repetitive Surge Current, TA = 25C (1/2 Cycle, Sine Wave, 60 Hz) Circuit Fusing Considerations (t = 8.3 ms) Peak Gate Power, TA = 25C Average Gate Power, TA = 25C Unit Volts 50 100 200 400 600 IT(RMS) 1.5 Amps ITSM 15 Amps I2t 0.9 A2s PGM 0.5 Watt PG(AV) 0.1 Watt Peak Forward Gate Current, TA = 25C (300 s, 120 PPS) IFGM 0.2 Amp Peak Reverse Gate Voltage VRGM 5 Volts Operating Junction Temperature Range @ Rated VRRM and VDRM Storage Temperature Range Lead Solder Temperature (Lead Length 1/16I from case, 10 s Max) q TJ -40 to +125 C Tstg -40 to +150 C -- +230 C 1. VDRM and VRRM for all types can be applied on a continuous basis. Ratings apply for zero or negative gate voltage; however, positive gate voltage shall not be applied concurrent with negative potential on the anode. Blocking voltages shall not be tested with a constant current source such that the voltage ratings of the devices are exceeded. Motorola Thyristor Device Data Motorola, Inc. 1995 1 THERMAL CHARACTERISTICS Symbol Max Unit Thermal Resistance, Junction to Case Characteristic RJC 50 C/W Thermal Resistance, Junction to Ambient RJA 160 C/W ELECTRICAL CHARACTERISTICS (TC = 25C unless otherwise noted. RGK = 1000 Ohms.) Characteristic Symbol Peak Forward or Reverse Blocking Current (VAK = Rated VDRM or VRRM) Min Typ Max Unit -- -- -- -- 10 200 A A VTM -- 1.2 1.7 Volts IDRM, IRRM TC = 25C TC = 125C Forward "On" Voltage (ITM = 1 A Peak) Gate Trigger Current (Continuous dc)(1) (Anode Voltage = 6 Vdc, RL = 100 Ohms) TC = 25C TC = -40C IGT -- -- 30 -- 200 500 A Gate Trigger Voltage (Continuous dc) (Anode Voltage = 7 Vdc, RL = 100 Ohms) (Anode Voltage = Rated VDRM, RL = 100 Ohms) TC = 25C TC = -40C TC = 125C VGT -- -- 0.1 -- -- -- 0.8 1.2 -- Volts Holding Current (Anode Voltage = 12 Vdc) TC = 25C TC = -40C IH -- -- 2 -- 5 10 mA dv/dt -- 25 -- V/s VGD Forward Voltage Application Rate (TC = 125C) 1. RGK Current Not Included in Measurement. FIGURE 1 -- MAXIMUM CASE TEMPERATURE 140 100 dc = 180 = CONDUCTION ANGLE 60 20 0 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 IT(AV), AVERAGE ON-STATE CURRENT (AMPS) 2 1.8 2.0 TA , MAXIMUM ALLOWABLE AMBIENT TEMPERATURE ( C) TC , MAXIMUM ALLOWABLE CASE TEMPERATURE ( C) CURRENT DERATING FIGURE 2 -- MAXIMUM AMBIENT TEMPERATURE 140 120 100 80 60 40 dc = 180 = CONDUCTION ANGLE 20 0 0 0.2 0.4 0.6 0.8 1.0 IT(AV), AVERAGE ON-STATE CURRENT (AMP) Motorola Thyristor Device Data FIGURE 3 -- TYPICAL FORWARD VOLTAGE 5.0 3.0 TJ = 125C 2.0 25C I T , INSTANTANEOUS ON-STATE CURRENT (AMP) 1.0 0.7 0.5 0.3 0.2 0.1 0.07 0.05 0.03 0.02 0.01 0 0.5 1.0 1.5 2.0 2.5 VT, INSTANTANEOUS ON-STATE VOLTAGE (VOLTS) r(t), TRANSIENT THERMAL RESISTANCE (NORMALIZED) FIGURE 4 -- THERMAL RESPONSE 1.0 0.7 0.5 0.3 0.2 0.1 0.07 0.05 0.03 0.02 0.01 0.1 0.2 0.5 1.0 2.0 5.0 10 20 50 100 200 500 1000 2000 5000 10000 t, TIME (ms) Motorola Thyristor Device Data 3 TYPICAL CHARACTERISTICS FIGURE 6 -- TYPICAL GATE TRIGGER CURRENT 100 0.8 VAK = 7.0 V RL = 100 0.7 I GT GATE TRIGGER CURRENT ( A) VG , GATE TRIGGER VOLTAGE (VOLTS) FIGURE 5 -- GATE TRIGGER VOLTAGE 0.6 0.5 0.4 0.3 -75 -50 -25 0 25 50 75 100 50 30 20 10 5.0 3.0 2.0 1.0 -40 125 -20 0 TJ, JUNCTION TEMPERATURE (C) I H , HOLDING CURRENT (mA) 10 VAK = 12 V RL = 100 2.0 1.0 -40 -20 0 20 40 60 80 100 TJ, JUNCTION TEMPERATURE (C) 4 120 140 160 P(AV) MAXIMUM AVERAGE POWER DISSIPATION (WATTS) FIGURE 7 -- HOLDING CURRENT 5.0 20 40 60 80 100 120 140 160 TJ JUNCTION TEMPERATURE (C) FIGURE 8 -- POWER DISSIPATION 2.0 1.8 1.6 30 1.4 60 90 120 180 1.2 1.0 dc 0.8 0.6 0.4 0.2 0 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 IT(AV), AVERAGE ON-STATE CURRENT (AMPS) Motorola Thyristor Device Data PACKAGE DIMENSIONS A B STYLE 10: PIN 1. CATHODE 2. GATE 3. ANODE R P L F SEATING PLANE K D X X G J H V C SECTION X-X 1 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. CONTOUR OF PACKAGE BEYOND DIMENSION R IS UNCONTROLLED. 4. DIMENSION F APPLIES BETWEEN P AND L. DIMENSION D AND J APPLY BETWEEN L AND K MINIMUM. LEAD DIMENSION IS UNCONTROLLED IN P AND BEYOND DIMENSION K MINIMUM. N N DIM A B C D F G H J K L N P R V INCHES MIN MAX 0.175 0.205 0.170 0.210 0.125 0.165 0.016 0.022 0.016 0.019 0.045 0.055 0.095 0.105 0.015 0.020 0.500 --- 0.250 --- 0.080 0.105 --- 0.100 0.115 --- 0.135 --- MILLIMETERS MIN MAX 4.45 5.20 4.32 5.33 3.18 4.19 0.41 0.55 0.41 0.48 1.15 1.39 2.42 2.66 0.39 0.50 12.70 --- 6.35 --- 2.04 2.66 --- 2.54 2.93 --- 3.43 --- CASE 29-04 (TO-226AA) Motorola Thyristor Device Data 5 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters can and do vary in different applications. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. Literature Distribution Centers: USA: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. EUROPE: Motorola Ltd.; European Literature Centre; 88 Tanners Drive, Blakelands, Milton Keynes, MK14 5BP, England. JAPAN: Nippon Motorola Ltd.; 4-32-1, Nishi-Gotanda, Shinagawa-ku, Tokyo 141, Japan. ASIA PACIFIC: Motorola Semiconductors H.K. Ltd.; Silicon Harbour Center, No. 2 Dai King Street, Tai Po Industrial Estate, Tai Po, N.T., Hong Kong. 6 Motorola Thyristor Device Data *MCR22-2/D* MCR22-2/D