BZX84C30VLFHT116 - ROHM SEMICONDUCTOR

BZX84C30VLFH

Zener Diode (AEC-Q101 qualified) Data sheet

　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　●Outline

PD250 mW 　　　

●Feature ●Inner Circuit

High reliability

Small mold type

●Application ●Packaging Specification

Voltage regulation Packing Embossed Tape

Reel Size(mm) 180

Taping Width(mm) 8

●Structure Basic Ordering Unit(pcs) 3000

Silicon Epitaxial Planar Taping Code T116

Marking D5E

●Absolute Maximum Rating (Ta = 25℃)

Parameter Symbol Condition Limits Unit

Power dissipation PDon Glass-epoxy substrate 250 mW

2.0 mW/°C

Junction temperature Tj- 150 ℃

Storage temperature Tstg - -65 ～ 150　℃

www.rohm.com

　2018/09/26_Rev.004

Not Recommended for

New Designs

BZX84CFH Series 　　　　　　　　　　　　　　　　　　　　　　 Data sheet

●Characteristic (Ta = 25ºC) 　　　　　　　　　　　　　　　　　　　　　　　　　　　　

P/N

Symbol

Zener Voltage:VZ(V) Reverse Current:

IR(μA)

Dynamic

Impedance:ZZ(Ω)

Temperature

Coefficient:γz

(mV/℃)

MIN. MAX. Iz

(mA) MAX. VR(V) MAX. Iz

(mA) MIN. MAX. Iz

(mA)

BZX84C2V4LFH 2.20 2.60 5 50 1.0 100 5 -3.0 0.0 5

BZX84C2V7LFH 2.50 2.90 5 20 1.0 100 5 -3.0 0.0 5

BZX84C3V0LFH 2.80 3.20 5 10 1.0 95 5 -3.0 0.0 5

BZX84C3V3LFH 3.10 3.50 5 5 1.0 95 5 -3.0 0.0 5

BZX84C3V6LFH 3.40 3.80 5 5 1.0 90 5 -3.0 0.0 5

BZX84C3V9LFH 3.70 4.10 5 3 1.0 90 5 -3.0 0.0 5

BZX84C4V3LFH 4.00 4.60 5 3 1.0 90 5 -3.0 0.0 5

BZX84C4V7LFH 4.40 5.00 5 3 2.0 80 5 -2.5 1.1 5

BZX84C5V1LFH 4.80 5.40 5 2 2.0 60 5 -1.5 2.6 5

BZX84C5V6LFH 5.20 6.00 5 1 2.0 40 5 -1.0 3.1 5

BZX84C6V2LFH 5.80 6.60 5 3 4.0 10 5 0.9 3.8 5

BZX84C6V8LFH 6.40 7.20 5 2 4.0 15 5 1.5 4.5 5

BZX84C7V5LFH 7.00 7.90 5 1 5.0 15 5 2.2 5.0 5

BZX84C8V2LFH 7.70 8.70 5 0.7 5.0 15 5 3.2 6.1 5

BZX84C9V1LFH 8.50 9.60 5 0.5 6.0 15 5 3.9 6.9 5

BZX84C10VLFH 9.40 10.60 5 0.2 7.0 20 5 5.0 8.0 5

BZX84C11VLFH 10.40 11.60 5 0.1 8.0 20 5 5.8 8.8 5

BZX84C12VLFH 11.40 12.70 5 0.1 8.0 25 5 6.8 9.8 5

BZX84C13VLFH 12.40 14.10 5 0.1 8.0 30 5 7.9 11.0 5

BZX84C15VLFH 13.80 15.60 5 0.1 10.0 30 5 9.4 12.6 5

BZX84C16VLFH 15.30 17.10 5 0.1 11.0 40 5 11.0 14.3 5

BZX84C18VLFH 16.80 19.10 5 0.1 13.0 45 5 12.6 15.8 5

BZX84C20VLFH 18.80 21.20 5 0.1 14.0 55 5 14.3 17.3 5

BZX84C22VLFH 20.80 23.30 5 0.1 15.0 55 5 15.8 19.3 5

BZX84C24VLFH 22.80 25.60 5 0.1 17.0 70 5 17.3 22.6 5

BZX84C27VLFH 25.10 28.90 2 0.1 19.0 80 2 19.3 25.8 2

BZX84C30VLFH 28.00 32.00 2 0.1 21.0 80 2 22.6 28.5 2

BZX84C33VLFH 31.00 35.00 2 0.1 23.0 80 2 25.8 31.1 2

BZX84C36VLFH 34.00 38.00 2 0.1 25.0 90 2 28.5 34.0 2

Z test time is 40ms 　　　　　　　　　　　　　　　　　　　　　　　　　　　　　

●Marking 　　　　　

P/N Marking P/N Marking

BZX84C2V4LFH D3C BZX84C10VLFH D3T

BZX84C2V7LFH D3D BZX84C11VLFH D3U

BZX84C3V0LFH D3E BZX84C12VLFH D3V

BZX84C3V3LFH D3F BZX84C13VLFH D3W

BZX84C3V6LFH D3G BZX84C15VLFH D3X

BZX84C3V9LFH D3H BZX84C16VLFH D3Y

BZX84C4V3LFH D3J BZX84C18VLFH D3Z

BZX84C4V7LFH D3K BZX84C20VLFH D5A

BZX84C5V1LFH D3L BZX84C22VLFH D5B

BZX84C5V6LFH D3M BZX84C24VLFH D5C

BZX84C6V2LFH D3N BZX84C27VLFH D5D

BZX84C6V8LFH D3P BZX84C30VLFH D5E

BZX84C7V5LFH D3Q BZX84C33VLFH D5F

BZX84C8V2LFH D3R BZX84C36VLFH D5G

BZX84C9V1LFH D3S 　　　　　　　　　　　　　　　　　　　　

www.rohm.com

2018/09/26_Rev.004

Not Recommended for

New Designs

BZX84C30VLFH 　　　　　　　　　　　　　　　　　　　　　　 Data sheet

●Characteristic Curves

www.rohm.com

Not Recommended for

New Designs

BZX84C30VLFH 　　　　　　　　　　　　　　　　　　　　　　 Data sheet

●Characteristic Curves

www.rohm.com

2018/09/26_Rev.004

Not Recommended for

New Designs

BZX84C30VLFH 　　　　　　　　　　　　　　　　　　　　　　 Data sheet

●Dimension (SSD3 SOT-23 )

●Taping (Unit:mm)

www.rohm.com

2018/09/26_Rev.004

Not Recommended for

New Designs

Notice-PAA-E Rev.004

Notice

Precaution on using ROHM Products

1. If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment (Note 1),

aircraft/spacecraft, nuclear power controllers, etc.) and whose malfunction or failure may cause loss of human life,

bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales

representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way

responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any

ROHM’s Products for Specific Applications.

(Note1) Medical Equipment Classification of the Specific Applications

JAPAN

USA

CHINA

CLASSⅢ

CLASSⅡb

CLASSⅢ

CLASSⅣ

CLASSⅢ

2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor

products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate

safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which

a failure or malfunction of our Products may cause. The following are examples of safety measures:

[a] Installation of protection circuits or other protective devices to improve system safety

[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure

3. Our Products are not designed under any special or extraordinary environments or conditions, as exemplified below.

Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the

use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our

Products under any special or extraordinary environments or conditions (as exemplified below), your independent

verification and confirmation of product performance, reliability, etc, prior to use, must be necessary:

[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents

[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust

[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,

H2S, NH3, SO2, and NO2

[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves

[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items

[f] Sealing or coating our Products with resin or other coating materials

[g] Use of our Products without cleaning residue of flux (Exclude cases where no-clean type fluxes is used.

However, recommend sufficiently about the residue.); or Washing our Products by using water or water-soluble

cleaning agents for cleaning residue after soldering

[h] Use of the Products in places subject to dew condensation

4. The Products are not subject to radiation-proof design.

5. Please verify and confirm characteristics of the final or mounted products in using the Products.

6.In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse, is applied,

confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power

exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect

product performance and reliability.

7.De-rate Power Dissipation depending on ambient temperature. When used in sealed area, confirm that it is the use in

the range that does not exceed the maximum junction temperature.

8.Confirm that operation temperature is within the specified range described in the product specification.

9.ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in

this document.

Precaution for Mounting / Circuit board design

1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product

performance and reliability.

2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must

be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products,

please consult with the ROHM representative in advance.

For details, please refer to ROHM Mounting specification

Not Recommended for

New Designs

Notice-PAA-E Rev.004

Precautions Regarding Application Examples and External Circuits

1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the

characteristics of the Products and external components, including transient characteristics, as well as static

characteristics.

2. You agree that application notes, reference designs, and associated data and information contained in this document

are presented only as guidance for Products use. Therefore, in case you use such information, you are solely

responsible for it and you must exercise your own independent verification and judgment in the use of such information

contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses

incurred by you or third parties arising from the use of such information.

Precaution for Electrostatic

This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper

caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be

applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron,

isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).

Precaution for Storage / Transportation

1. Product performance and soldered connections may deteriorate if the Products are stored in the places where:

[a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2

[b] the temperature or humidity exceeds those recommended by ROHM

[c] the Products are exposed to direct sunshine or condensation

[d] the Products are exposed to high Electrostatic

2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period

may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is

exceeding the recommended storage time period.

3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads

may occur due to excessive stress applied when dropping of a carton.

4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of

which storage time is exceeding the recommended storage time period.

Precaution for Product Label

A two-dimensional barcode printed on ROHM Products label is for ROHM’s internal use only.

Precaution for Disposition

When disposing Products please dispose them properly using an authorized industry waste company.

Precaution for Foreign Exchange and Foreign Trade act

Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreign

trade act, please consult with ROHM in case of export.

Precaution Regarding Intellectual Property Rights

1. All information and data including but not limited to application example contained in this document is for reference

only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any

other rights of any third party regarding such information or data.

2. ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the

Products with other articles such as components, circuits, systems or external equipment (including software).

3. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any

third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM

will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to

manufacture or sell products containing the Products, subject to the terms and conditions herein.

Other Precaution

1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.

2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written

consent of ROHM.

3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the

Products or this document for any military purposes, including but not limited to, the development of mass-destruction

weapons.

4. The proper names of companies or products described in this document are trademarks or registered trademarks of

ROHM, its affiliated companies or third parties.

Not Recommended for

New Designs

DatasheetDatasheet

Notice – WE Rev.001

General Precaution

1. Before you use our Products, you are requested to carefully read this document and fully understand its contents.

ROHM shall not be in any way responsible or liable for failure, malfunction or accident arising from the use of any

ROHM’s Products against warning, caution or note contained in this document.

2. All information contained in this document is current as of the issuing date and subject to change without any prior

notice. Before purchasing or using ROHM’s Products, please confirm the latest information with a ROHM sales

representative.

3. The information contained in this document is provided on an “as is” basis and ROHM does not warrant that all

information contained in this document is accurate and/or error-free. ROHM shall not be in any way responsible or

liable for any damages, expenses or losses incurred b y you or third parties resulting from inaccuracy or errors of or

concerning such information.

Not Recommended for

New Designs