Intel(R) 8 Series/C220 Series Chipset Family Platform Controller Hub (PCH) Datasheet May 2014 328904-003 INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH INTEL PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED IN INTEL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, INTEL ASSUMES NO LIABILITY WHATSOEVER AND INTEL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO SALE AND/OR USE OF INTEL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. A "Mission Critical Application" is any application in which failure of the Intel Product could result, directly or indirectly, in personal injury or death. SHOULD YOU PURCHASE OR USE INTEL'S PRODUCTS FOR ANY SUCH MISSION CRITICAL APPLICATION, YOU SHALL INDEMNIFY AND HOLD INTEL AND ITS SUBSIDIARIES, SUBCONTRACTORS AND AFFILIATES, AND THE DIRECTORS, OFFICERS, AND EMPLOYEES OF EACH, HARMLESS AGAINST ALL CLAIMS COSTS, DAMAGES, AND EXPENSES AND REASONABLE ATTORNEYS' FEES ARISING OUT OF, DIRECTLY OR INDIRECTLY, ANY CLAIM OF PRODUCT LIABILITY, PERSONAL INJURY, OR DEATH ARISING IN ANY WAY OUT OF SUCH MISSION CRITICAL APPLICATION, WHETHER OR NOT INTEL OR ITS SUBCONTRACTOR WAS NEGLIGENT IN THE DESIGN, MANUFACTURE, OR WARNING OF THE INTEL PRODUCT OR ANY OF ITS PARTS. Intel may make changes to specifications and product descriptions at any time, without notice. Designers must not rely on the absence or characteristics of any features or instructions marked "reserved" or "undefined". Intel reserves these for future definition and shall have no responsibility whatsoever for conflicts or incompatibilities arising from future changes to them. The information here is subject to change without notice. Do not finalize a design with this information. The products described in this document may contain design defects or errors known as errata which may cause the product to deviate from published specifications. Current characterized errata are available on request. Contact your local Intel sales office or your distributor to obtain the latest specifications and before placing your product order. Copies of documents which have an order number and are referenced in this document, or other Intel literature, may be obtained by calling 1-800-5484725, or go to: http://www.intel.com/design/literature.htm. Code names featured are used internally within Intel to identify products that are in development and not yet publicly announced for release. Customers, licensees and other third parties are not authorized by Intel to use code names in advertising, promotion or marketing of any product or services and any such use of Intel's internal code names is at the sole risk of the user. I2C is a two-wire communications bus/protocol developed by NXP. SMBus is a subset of the I2C bus/protocol and was developed by Intel. Implementations of the I2C bus/protocol may require licenses from various entities, including NXP Semiconductors N.V. Intel(R) Anti-Theft Technology (Intel(R) AT): No system can provide absolute security under all conditions. Requires an enabled chipset, BIOS, firmware and software and a subscription with a capable Service Provider. Consult your System manufacturer and Service Provider for availability and functionality. Intel assumes no liability for lost or stolen data and/or systems or any other damages resulting thereof. For more information, visit http:// www.intel.com/go/anti-theft Intel(R) High Definition Audio (Intel(R) HD Audio): Requires an Intel(R) HD Audio enabled system. Consult your PC manufacturer for more information. Sound quality will depend on equipment and actual implementation. For more information about Intel(R) HD Audio, refer to http://www.intel.com/design/ chipsets/hdaudio.htm Intel(R) Trusted Execution Technology (Intel(R) TXT): No computer system can provide absolute security under all conditions. Intel(R) TXT requires a computer system with Intel(R) Virtualization Technology, an Intel TXT-enabled processor, chipset, BIOS, Authenticated Code Modules and an Intel TXT compatible measured launched environment (MLE). The MLE could consist of a virtual machine monitor, an OS or an application. In addition, Intel TXT requires the system to contain a TPM v1.2, as defined by the Trusted Computing Group and specific software for some uses. For more information, see http://www.intel.com/technology/security Intel(R) Active Management Technology (Intel(R) AMT) requires activation and a system with a corporate network connection, an Intel(R) AMT-enabled chipset, network hardware and software. For notebooks, Intel AMT may be unavailable or limited over a host OS-based VPN, when connecting wirelessly, on battery power, sleeping, hibernating or powered off. Results dependent upon hardware, setup and configuration. For more information, visit http:// www.intel.com/technology/platform-technology/intel-amt No computer system can provide absolute security under all conditions. Intel(R) Trusted Execution Technology (Intel(R) TXT) requires a computer system with Intel(R) Virtualization Technology, an Intel TXT-enabled processor, chipset, BIOS, Authenticated Code Modules and an Intel TXT-compatible Measured Launched Environment (MLE). Intel TXT also requires the system to contain a TPM v1.s. For more information, visit http://www.intel.com/technology/ security Intel(R) Virtualization Technology requires a computer system with an enabled Intel(R) processor, BIOS, virtual machine monitor (VMM). Functionality, performance or other benefits will vary depending on hardware and software configurations. Software applications may not be compatible with all operating systems. Consult your PC manufacturer. For more information, visit http://www.intel.com/go/virtualization. Intel(R) vProTM Technology is sophisticated and requires setup and activation. Availability of features and results will depend upon the setup and configuration of your hardware, software and IT environment. To learn more visit: http://www.intel.com/technology/vpro Intel, Pentium, Intel vPro, Xeon, Intel Core, and the Intel logo are trademarks of Intel Corporation in the U.S. and other countries. *Other names and brands may be claimed as the property of others. Copyright (c) 2013-2014, Intel Corporation. All rights reserved. 2 Datasheet Contents 1 Introduction ............................................................................................................ 41 1.1 About This Manual ............................................................................................. 41 1.1.1 Chapter Descriptions ............................................................................. 42 1.2 Overview ......................................................................................................... 44 1.2.1 Capability Overview............................................................................... 45 1.3 Intel(R) 8 Series/C220 Series Chipset Family PCH SKU Definition ............................... 52 1.4 Device and Revision ID Table .............................................................................. 57 2 Signal Description ................................................................................................... 60 2.1 Flexible I/O ...................................................................................................... 62 2.2 USB Interface ................................................................................................... 63 2.3 PCI Express* .................................................................................................... 66 2.4 Serial ATA Interface........................................................................................... 67 2.5 Clock Signals .................................................................................................... 69 2.6 Real Time Clock Interface ................................................................................... 70 2.7 External RTC Circuitry ........................................................................................ 71 2.8 Interrupt Interface ............................................................................................ 71 2.9 Processor Interface............................................................................................ 72 2.10 Direct Media Interface (DMI) to Host Controller ..................................................... 72 2.11 Intel(R) Flexible Display Interface (Intel(R) FDI) ........................................................ 73 2.12 Analog Display/VGA DAC Signals ......................................................................... 73 2.13 Digital Display Signals........................................................................................ 73 2.14 Embedded DisplayPort* (eDP*) Backlight Control Signals ....................................... 74 2.15 Intel(R) High Definition Audio (Intel(R) HD Audio) Link ............................................... 74 2.16 Low Pin Count (LPC) Interface............................................................................. 75 2.17 General Purpose I/O Signals ............................................................................... 75 2.18 Functional Straps .............................................................................................. 81 2.19 SMBus Interface................................................................................................ 84 2.20 System Management Interface............................................................................ 85 2.21 Controller Link .................................................................................................. 85 2.22 Serial Peripheral Interface (SPI) .......................................................................... 85 2.23 Manageability Signals ........................................................................................ 86 2.24 Power Management Interface.............................................................................. 87 2.25 Power and Ground Signals .................................................................................. 90 2.26 Thermal Signals ................................................................................................ 91 2.27 Miscellaneous Signals ........................................................................................ 92 2.28 Testability Signals ............................................................................................. 93 2.29 Reserved / Test Pins .......................................................................................... 93 3 PCH Pin States......................................................................................................... 95 3.1 Integrated Pull-Ups and Pull-Downs ..................................................................... 95 3.2 Output Signals Planes and States ........................................................................ 97 3.3 Input and I/O Signals Planes and States............................................................. 102 4 PCH and System Clocks ......................................................................................... 107 4.1 Straps Related to Clock Configuration ................................................................ 107 4.2 Platform Clocking Requirements ........................................................................ 107 4.3 Functional Blocks ............................................................................................ 109 4.4 Clock Configuration Access Overview ................................................................. 111 5 Functional Description ........................................................................................... 112 5.1 Flexible I/O .................................................................................................... 112 5.2 PCI-to-PCI Bridge............................................................................................ 113 5.2.1 PCI Bus Interface ................................................................................ 113 5.2.2 PCI Legacy Mode................................................................................. 113 5.3 PCI Express* Root Ports (D28:F0~F7)................................................................ 113 5.3.1 Supported PCI Express* (PCIe*) Port Configurations................................ 114 5.3.2 Interrupt Generation ........................................................................... 114 5.3.3 Power Management ............................................................................. 115 5.3.3.1 S3/S4/S5 Support................................................................. 115 5.3.3.2 Resuming from Suspended State............................................. 115 5.3.3.3 Device Initiated PM_PME Message ........................................... 115 Datasheet 3 5.4 5.5 5.6 5.7 5.8 5.9 4 5.3.3.4 SMI/SCI Generation............................................................... 116 5.3.3.5 Latency Tolerance Reporting (LTR) .......................................... 116 5.3.3.6 Opportunistic Buffer Flush/Fill (OBFF)....................................... 116 5.3.4 SERR# Generation............................................................................... 116 5.3.5 Hot-Plug............................................................................................. 117 5.3.5.1 Presence Detection ................................................................ 117 5.3.5.2 SMI/SCI Generation............................................................... 117 Gigabit Ethernet Controller (B0:D25:F0) ............................................................. 118 5.4.1 GbE PCI Express* Bus Interface ............................................................ 120 5.4.1.1 Transaction Layer .................................................................. 120 5.4.1.2 Data Alignment ..................................................................... 120 5.4.1.3 Configuration Request Retry Status.......................................... 120 5.4.2 Error Events and Error Reporting ........................................................... 121 5.4.2.1 Data Parity Error ................................................................... 121 5.4.2.2 Completion with Unsuccessful Completion Status ....................... 121 5.4.3 Ethernet Interface ............................................................................... 121 5.4.3.1 Intel(R) Ethernet Network Connection I127LM/V Platform LAN Connect Device Interface........................................................ 121 5.4.4 PCI Power Management........................................................................ 122 5.4.4.1 Wake Up .............................................................................. 122 5.4.5 Configurable LEDs ............................................................................... 124 5.4.6 Function Level Reset Support (FLR)........................................................ 125 5.4.6.1 FLR Steps............................................................................. 125 Low Pin Count (LPC) Bridge (with System and Management Functions) (D31:F0) ...................................................................... 126 5.5.1 LPC Interface ...................................................................................... 126 5.5.1.1 LPC Cycle Types .................................................................... 127 5.5.1.2 Start Field Definition .............................................................. 127 5.5.1.3 Cycle Type / Direction (CYCTYPE + DIR) ................................... 127 5.5.1.4 Size..................................................................................... 128 5.5.1.5 SYNC ................................................................................... 128 5.5.1.6 SYNC Time-Out ..................................................................... 128 5.5.1.7 SYNC Error Indication ............................................................ 129 5.5.1.8 LFRAME# Usage .................................................................... 129 5.5.1.9 I/O Cycles ............................................................................ 129 5.5.1.10 Bus Master Cycles ................................................................. 129 5.5.1.11 LPC Power Management ......................................................... 129 5.5.1.12 Configuration and PCH Implications ......................................... 130 DMA Operation (D31:F0) .................................................................................. 130 5.6.1 Channel Priority................................................................................... 131 5.6.1.1 Fixed Priority ........................................................................ 131 5.6.1.2 Rotating Priority .................................................................... 131 5.6.2 Address Compatibility Mode .................................................................. 131 5.6.3 Summary of DMA Transfer Sizes............................................................ 132 5.6.3.1 Address Shifting When Programmed for 16-Bit I/O Count by Words ............................................................................. 132 5.6.4 Autoinitialize ....................................................................................... 132 5.6.5 Software Commands ............................................................................ 133 Low Pin Count (LPC) DMA ................................................................................. 133 5.7.1 Asserting DMA Requests ....................................................................... 133 5.7.2 Abandoning DMA Requests ................................................................... 134 5.7.3 General Flow of DMA Transfers .............................................................. 134 5.7.4 Terminal Count ................................................................................... 135 5.7.5 Verify Mode ........................................................................................ 135 5.7.6 DMA Request De-assertion.................................................................... 135 5.7.7 SYNC Field / LDRQ# Rules .................................................................... 136 8254 Timers (D31:F0) ...................................................................................... 136 5.8.1 Timer Programming ............................................................................. 137 5.8.2 Reading from the Interval Timer ............................................................ 138 5.8.2.1 Simple Read ......................................................................... 138 5.8.2.2 Counter Latch Command ........................................................ 138 5.8.2.3 Read Back Command ............................................................. 139 8259 Programmable Interrupt Controllers (PIC) (D31:F0) ..................................... 139 5.9.1 Interrupt Handling ............................................................................... 140 5.9.1.1 Generating Interrupts ............................................................ 140 5.9.1.2 Acknowledging Interrupts ....................................................... 140 5.9.1.3 Hardware/Software Interrupt Sequence.................................... 141 Datasheet 5.9.2 5.10 5.11 5.12 5.13 5.14 Datasheet Initialization Command Words (ICWx).................................................... 141 5.9.2.1 ICW1 .................................................................................. 141 5.9.2.2 ICW2 .................................................................................. 142 5.9.2.3 ICW3 .................................................................................. 142 5.9.2.4 ICW4 .................................................................................. 142 5.9.3 Operation Command Words (OCW)........................................................ 142 5.9.4 Modes of Operation ............................................................................. 143 5.9.4.1 Fully Nested Mode................................................................. 143 5.9.4.2 Special Fully-Nested Mode...................................................... 143 5.9.4.3 Automatic Rotation Mode (Equal Priority Devices)...................... 143 5.9.4.4 Specific Rotation Mode (Specific Priority).................................. 143 5.9.4.5 Poll Mode ............................................................................. 144 5.9.4.6 Edge and Level Triggered Mode............................................... 144 5.9.4.7 End of Interrupt (EOI) Operations ........................................... 144 5.9.4.8 Normal End of Interrupt ......................................................... 144 5.9.4.9 Automatic End of Interrupt Mode............................................. 145 5.9.5 Masking Interrupts .............................................................................. 145 5.9.5.1 Masking on an Individual Interrupt Request .............................. 145 5.9.5.2 Special Mask Mode ................................................................ 145 5.9.6 Steering PCI Interrupts ........................................................................ 145 Advanced Programmable Interrupt Controller (APIC) (D31:F0) .............................. 146 5.10.1 Interrupt Handling............................................................................... 146 5.10.2 Interrupt Mapping ............................................................................... 146 5.10.3 PCI / PCI Express* Message-Based Interrupts......................................... 147 5.10.4 IOxAPIC Address Remapping ................................................................ 147 5.10.5 External Interrupt Controller Support..................................................... 147 Serial Interrupt (D31:F0) ................................................................................. 148 5.11.1 Start Frame........................................................................................ 148 5.11.2 Data Frames ...................................................................................... 148 5.11.3 Stop Frame ........................................................................................ 149 5.11.4 Specific Interrupts Not Supported Using SERIRQ ..................................... 149 5.11.5 Data Frame Format ............................................................................. 149 Real Time Clock (D31:F0)................................................................................. 150 5.12.1 Update Cycles..................................................................................... 151 5.12.2 Interrupts .......................................................................................... 151 5.12.3 Lockable RAM Ranges .......................................................................... 151 5.12.4 Century Rollover ................................................................................. 151 5.12.5 Clearing Battery-Backed RTC RAM ......................................................... 151 Processor Interface (D31:F0) ............................................................................ 153 5.13.1 Processor Interface Signals and VLW Messages ....................................... 153 5.13.1.1 INIT (Initialization)................................................................ 153 5.13.1.2 FERR# (Numeric Coprocessor Error) ........................................ 153 5.13.1.3 NMI (Non-Maskable Interrupt) ................................................ 154 5.13.1.4 Processor Power Good (PROCPWRGD)...................................... 154 5.13.2 Dual-Processor Issues.......................................................................... 154 5.13.2.1 Usage Differences ................................................................. 154 5.13.3 Virtual Legacy Wire (VLW) Messages ..................................................... 154 Power Management ......................................................................................... 155 5.14.1 Features ............................................................................................ 155 5.14.2 PCH and System Power States .............................................................. 155 5.14.3 System Power Planes........................................................................... 157 5.14.4 SMI# / SCI Generation ........................................................................ 157 5.14.4.1 PCI Express* SCI .................................................................. 160 5.14.4.2 PCI Express* Hot-Plug ........................................................... 160 5.14.5 C-States ............................................................................................ 160 5.14.6 Dynamic 33 MHz Clock Control (Mobile Only) .......................................... 160 5.14.6.1 Conditions for Checking the 33 MHz Clock ................................ 161 5.14.6.2 Conditions for Maintaining the 33MHz Clock .............................. 161 5.14.6.3 Conditions for Stopping the 33MHz Clock ................................. 161 5.14.6.4 Conditions for Re-Starting the 33MHz Clock .............................. 161 5.14.6.5 LPC Devices and CLKRUN#..................................................... 161 5.14.7 Sleep States....................................................................................... 162 5.14.7.1 Sleep State Overview ............................................................ 162 5.14.7.2 Initiating Sleep State............................................................. 162 5.14.7.3 Exiting Sleep States .............................................................. 162 5.14.7.4 PCI Express* WAKE# Signal and PME Event Message................. 164 5.14.7.5 Sx-G3-Sx, Handling Power Failures.......................................... 164 5 5.14.7.6 Deep Sx ............................................................................... 165 Event Input Signals and Their Usage ...................................................... 166 5.14.8.1 PWRBTN# (Power Button) ...................................................... 166 5.14.8.2 RI# (Ring Indicator) .............................................................. 167 5.14.8.3 PME# (PCI Power Management Event) ..................................... 168 5.14.8.4 SYS_RESET# Signal............................................................... 168 5.14.8.5 THRMTRIP# Signal ................................................................ 168 5.14.9 ALT Access Mode ................................................................................. 169 5.14.9.1 Write Only Registers with Read Paths in ALT Access Mode ........... 170 5.14.9.2 PIC Reserved Bits .................................................................. 171 5.14.9.3 Read Only Registers with Write Paths in ALT Access Mode ........... 171 5.14.10 System Power Supplies, Planes, and Signals ........................................... 172 5.14.10.1 Power Plane Control with SLP_S3#, SLP_S4#, SLP_S5#, SLP_A# and SLP_LAN#............................. 172 5.14.10.2 SLP_S4# and Suspend-To-RAM Sequencing .............................. 172 5.14.10.3 PWROK Signal....................................................................... 173 5.14.10.4 BATLOW# (Battery Low) (Mobile Only) ..................................... 173 5.14.10.5 SLP_LAN# Pin Behavior.......................................................... 173 5.14.10.6 SLP_WLAN# Pin Behavior ....................................................... 175 5.14.10.7 SUSPWRDNACK/SUSWARN#/GPIO30 Steady State Pin Behavior .. 175 5.14.10.8 RTCRST# and SRTCRST# ....................................................... 176 5.14.11 Legacy Power Management Theory of Operation ...................................... 176 5.14.11.1 APM Power Management (Desktop Only) .................................. 176 5.14.11.2 Mobile APM Power Management (Mobile Only) ........................... 176 5.14.12 Reset Behavior.................................................................................... 177 System Management (D31:F0) .......................................................................... 178 5.15.1 Theory of Operation ............................................................................. 179 5.15.1.1 Detecting a System Lockup..................................................... 179 5.15.1.2 Handling an Intruder.............................................................. 179 5.15.1.3 Detecting Improper Flash Programming.................................... 180 5.15.1.4 Heartbeat and Event Reporting using SMLink/SMBus .................. 180 5.15.2 TCO Modes ......................................................................................... 180 5.15.2.1 TCO Legacy / Compatible Mode ............................................... 180 5.15.2.2 Advanced TCO Mode .............................................................. 181 General Purpose I/O (D31:F0) ........................................................................... 182 5.16.1 Power Wells ........................................................................................ 182 5.16.2 SMI#, SCI, and NMI Routing ................................................................. 182 5.16.3 Triggering .......................................................................................... 183 5.16.4 GPIO Registers Lockdown ..................................................................... 183 5.16.5 Serial POST Codes over GPIO ................................................................ 183 5.16.5.1 Theory of Operation ............................................................... 184 5.16.5.2 Serial Message Format ........................................................... 185 SATA Host Controller (D31:F2, F5)..................................................................... 186 5.17.1 SATA 6 Gb/s Support ........................................................................... 186 5.17.2 SATA Feature Support .......................................................................... 186 5.17.3 Theory of Operation ............................................................................. 187 5.17.3.1 Standard ATA Emulation......................................................... 187 5.17.3.2 48-Bit LBA Operation ............................................................. 188 5.17.4 SATA Swap Bay Support....................................................................... 188 5.17.5 Hot-Plug Operation .............................................................................. 188 5.17.6 Intel(R) Rapid Storage Technology (Intel RST(R)) Configuration ..................... 188 5.17.6.1 Intel(R) Rapid Storage Technology (Intel(R) RST) RAID Option ROM . 189 5.17.7 Intel(R) Smart Response Technology ........................................................ 189 5.17.8 Power Management Operation ............................................................... 189 5.17.8.1 Power State Mappings ............................................................ 190 5.17.8.2 Power State Transitions.......................................................... 190 5.17.8.3 SMI Trapping (APM)............................................................... 191 5.17.9 SATA Device Presence.......................................................................... 191 5.17.10 SATA LED ........................................................................................... 192 5.17.11 AHCI Operation ................................................................................... 192 5.17.12 SGPIO Signals..................................................................................... 193 5.17.12.1 Mechanism ........................................................................... 193 5.17.12.2 Message Format .................................................................... 194 5.17.12.3 LED Message Type................................................................. 194 5.17.12.4 SGPIO Waveform .................................................................. 196 5.17.13 External SATA ..................................................................................... 197 High Precision Event Timers (HPET).................................................................... 197 5.14.8 5.15 5.16 5.17 5.18 6 Datasheet 5.19 5.20 5.21 5.22 5.23 5.24 Datasheet 5.18.1 Timer Accuracy ................................................................................... 197 5.18.2 Interrupt Mapping ............................................................................... 197 5.18.3 Periodic versus Non-Periodic Modes ....................................................... 199 5.18.4 Enabling the Timers............................................................................. 199 5.18.5 Interrupt Levels .................................................................................. 200 5.18.6 Handling Interrupts ............................................................................. 200 5.18.7 Issues Related to 64-Bit Timers with 32-Bit Processors............................. 200 USB EHCI Host Controllers (D29:F0 and D26:F0)................................................. 201 5.19.1 EHC Initialization ................................................................................ 201 5.19.1.1 BIOS Initialization ................................................................. 201 5.19.1.2 Driver Initialization................................................................ 201 5.19.1.3 EHC Resets .......................................................................... 201 5.19.2 Data Structures in Main Memory ........................................................... 201 5.19.3 USB 2.0 Enhanced Host Controller DMA ................................................. 202 5.19.4 Data Encoding and Bit Stuffing.............................................................. 202 5.19.5 Packet Formats ................................................................................... 202 5.19.6 USB 2.0 Interrupts and Error Conditions................................................. 202 5.19.6.1 Aborts on USB 2.0-Initiated Memory Reads .............................. 203 5.19.7 USB 2.0 Power Management................................................................. 203 5.19.7.1 Pause Feature ...................................................................... 203 5.19.7.2 Suspend Feature................................................................... 203 5.19.7.3 ACPI Device States................................................................ 203 5.19.7.4 ACPI System States .............................................................. 204 5.19.8 USB 2.0 Legacy Keyboard Operation...................................................... 204 5.19.9 USB 2.0 Based Debug Port ................................................................... 204 5.19.9.1 Theory of Operation ............................................................. 205 5.19.10 EHCI Caching ..................................................................................... 209 (R) 5.19.11 Intel USB Prefetch Based Pause .......................................................... 209 5.19.12 Function Level Reset Support (FLR) ....................................................... 209 5.19.12.1 FLR Steps ............................................................................ 210 5.19.13 USB Overcurrent Protection .................................................................. 210 Integrated USB 2.0 Rate Matching Hub .............................................................. 211 5.20.1 Overview ........................................................................................... 211 5.20.2 Architecture ....................................................................................... 211 xHCI Controller (D20:F0) ................................................................................. 212 SMBus Controller (D31:F3) ............................................................................... 212 5.22.1 Host Controller ................................................................................... 213 5.22.1.1 Command Protocols .............................................................. 213 5.22.2 Bus Arbitration ................................................................................... 217 5.22.3 Bus Timing......................................................................................... 217 5.22.3.1 Clock Stretching ................................................................... 217 5.22.3.2 Bus Time Out (The PCH as SMBus Master)................................ 217 5.22.4 Interrupts / SMI# ............................................................................... 217 5.22.5 SMBALERT# ....................................................................................... 218 5.22.6 SMBus CRC Generation and Checking .................................................... 219 5.22.7 SMBus Slave Interface ......................................................................... 219 5.22.7.1 Format of Slave Write Cycle ................................................... 220 5.22.7.2 Format of Read Command...................................................... 221 5.22.7.3 Slave Read of RTC Time Bytes ................................................ 222 5.22.7.4 Format of Host Notify Command ............................................. 223 Thermal Management ...................................................................................... 224 5.23.1 Thermal Sensor .................................................................................. 224 5.23.1.1 Internal Thermal Sensor Operation.......................................... 224 5.23.2 PCH Thermal Throttling ........................................................................ 225 5.23.3 Thermal Reporting Over System Management Link 1 Interface (SMLink1) ... 226 5.23.3.1 Block Read Address ............................................................... 227 5.23.3.2 Block Read Command ............................................................ 227 5.23.3.3 Read Data Format ................................................................. 227 5.23.3.4 Thermal Data Update Rate ..................................................... 227 5.23.3.5 Temperature Comparator and Alert ......................................... 228 5.23.3.6 BIOS Set Up......................................................................... 229 5.23.3.7 SMBus Rules ........................................................................ 229 5.23.3.8 Case for Considerations ......................................................... 230 (R) High Definition Audio (Intel(R) HD Audio) Overview (D27:F0) ........................ 232 Intel 5.24.1 Intel(R) High Definition Audio (Intel(R) HD Audio) Docking (Mobile Only) ........ 232 5.24.1.1 Dock Sequence ..................................................................... 232 5.24.1.2 Exiting D3/CRST# When Docked ............................................. 233 7 5.25 5.26 5.27 5.28 5.29 5.24.1.3 Cold Boot/Resume from S3 When Docked ................................. 234 5.24.1.4 Undock Sequence .................................................................. 234 5.24.1.5 Normal Undock ..................................................................... 234 5.24.1.6 Surprise Undock .................................................................... 235 5.24.1.7 Interaction between Dock/Undock and Power Management States 235 5.24.1.8 Relationship between HDA_DOCK_RST# and HDA_RST# ............ 235 Intel(R) Management Engine (Intel(R) ME) and Intel(R) Management Engine Firmware (Intel(R) ME FW) 9.0 ............................................... 236 5.25.1 Intel(R) Management Engine (Intel(R) ME) Requirements.............................. 237 Serial Peripheral Interface (SPI) ........................................................................ 238 5.26.1 SPI Supported Feature Overview ........................................................... 238 5.26.1.1 Non-Descriptor Mode ............................................................. 238 5.26.1.2 Descriptor Mode .................................................................... 239 5.26.2 Flash Descriptor .................................................................................. 240 5.26.2.1 Descriptor Master Region........................................................ 241 5.26.3 Flash Access ....................................................................................... 241 5.26.3.1 Direct Access Security ............................................................ 242 5.26.3.2 Register Access Security......................................................... 242 5.26.4 Serial Flash Device Compatibility Requirements ....................................... 242 5.26.4.1 PCH SPI Based BIOS Requirements.......................................... 242 5.26.4.2 Integrated LAN Firmware SPI Flash Requirements...................... 243 5.26.4.3 Intel(R) Management Engine Firmware (Intel(R) ME FW) SPI Flash Requirements ....................................................................... 243 5.26.4.4 Hardware Sequencing Requirements ........................................ 244 5.26.5 Multiple Page Write Usage Model ........................................................... 245 5.26.5.1 Soft Flash Protection .............................................................. 245 5.26.5.2 BIOS Range Write Protection................................................... 246 5.26.5.3 SMI# Based Global Write Protection ......................................... 246 5.26.6 Flash Device Configurations .................................................................. 246 5.26.7 SPI Flash Device Recommended Pinout................................................... 246 5.26.8 Serial Flash Device Package .................................................................. 247 5.26.8.1 Common Footprint Usage Model .............................................. 247 5.26.8.2 Serial Flash Device Package Recommendations.......................... 247 5.26.9 PWM Outputs (Server/Workstation Only) ................................................ 247 5.26.10 TACH Inputs (Server/Workstation Only) ................................................. 248 Feature Capability Mechanism ........................................................................... 248 PCH Display Interface and Intel(R) Flexible Display Interface (Intel(R) FDI) Interconnect ................................................................................................... 248 5.28.1 Analog Display Interface Characteristics ................................................. 249 5.28.1.1 Integrated RAMDAC ............................................................... 250 5.28.1.2 DDC (Display Data Channel) ................................................... 250 5.28.2 Digital Display Side Band Signals ........................................................... 250 5.28.2.1 DisplayPort AUX CH ............................................................... 251 5.28.2.2 DDC (Display Data Channel) ................................................... 251 5.28.2.3 Hot-Plug Detect..................................................................... 251 5.28.2.4 Map of Digital Display Side Band Signals Per Display Configuration ........................................................................ 251 5.28.2.5 Panel Power Sequencing and Backlight Control .......................... 251 5.28.3 Intel(R) Flexible Display Interface (Intel(R) FDI) .......................................... 252 Intel(R) Virtualization Technology (Intel(R) VT) ........................................................ 253 5.29.1 Intel(R) Virtualization Technology (Intel(R) VT) for Directed I/O (Intel(R) VT-d) Objectives..................................................... 253 5.29.2 Intel(R) VT-d Features Supported ............................................................ 253 5.29.3 Support for Function Level Reset (FLR) in PCH......................................... 253 5.29.4 Virtualization Support for PCH IOxAPIC................................................... 254 5.29.5 Virtualization Support for High Precision Event Timer (HPET) ..................... 254 6 Ballout Definition ................................................................................................... 255 6.1 Desktop/Server PCH Ballout .............................................................................. 255 6.2 Mobile PCH Ballout ........................................................................................... 264 7 Package Information ............................................................................................. 272 7.1 Desktop/Server PCH Package ............................................................................ 272 7.1.1 Tape and Reel Pin 1 Placement .............................................................. 272 7.2 Mobile PCH Package ......................................................................................... 274 7.2.1 Tape and Reel Pin 1 Placement .............................................................. 274 8 Datasheet 8 Electrical Characteristics ....................................................................................... 276 8.1 Thermal Specifications ..................................................................................... 276 8.1.1 Storage Specifications and Thermal Design Power (TDP) .......................... 276 8.2 Absolute Maximum Ratings............................................................................... 277 8.3 PCH Power Supply Range ................................................................................. 277 8.4 General DC Characteristics ............................................................................... 278 8.5 Display DC Characteristics ................................................................................ 287 8.6 AC Characteristics ........................................................................................... 288 8.7 Power Sequencing and Reset Signal Timings ....................................................... 299 8.8 Power Management Timing Diagrams................................................................. 303 8.9 AC Timing Diagrams ........................................................................................ 308 8.10 Sequencing Rails Within The Same Well ............................................................. 319 9 Register and Memory Mapping............................................................................... 320 9.1 PCI Devices and Functions................................................................................ 321 9.2 PCI Configuration Map ..................................................................................... 322 9.3 I/O Map ......................................................................................................... 322 9.3.1 Fixed I/O Address Ranges .................................................................... 322 9.3.2 Variable I/O Decode Ranges ................................................................. 324 9.4 Memory Map................................................................................................... 325 9.4.1 Boot-Block Update Scheme .................................................................. 327 10 Chipset Configuration Registers............................................................................. 329 10.1 Chipset Configuration Registers (Memory Space) ................................................. 329 10.1.1 RPC--Root Port Configuration Register ................................................... 331 10.1.2 RPFN--Root Port Function Number and Hide for PCI Express* Root Ports Register ................................................................ 331 10.1.3 FLRSTAT--Function Level Reset Pending Status Register........................... 333 10.1.4 TRSR--Trap Status Register.................................................................. 333 10.1.5 TRCR--Trapped Cycle Register .............................................................. 334 10.1.6 TWDR--Trapped Write Data Register...................................................... 334 10.1.7 IOTRn--I/O Trap Register (0-3) ............................................................ 335 10.1.8 V0CTL--Virtual Channel 0 Resource Control Register ................................ 336 10.1.9 V0STS--Virtual Channel 0 Resource Status Register................................. 336 10.1.10 V1CTL--Virtual Channel 1 Resource Control Register ................................ 336 10.1.11 V1STS--Virtual Channel 1 Resource Status Register................................. 337 10.1.12 REC--Root Error Command Register ...................................................... 337 10.1.13 LCAP--Link Capabilities Register............................................................ 337 10.1.14 LCTL--Link Control Register.................................................................. 338 10.1.15 LSTS--Link Status Register................................................................... 338 10.1.16 TCTL--TCO Configuration Register ........................................................ 338 10.1.17 D31IP--Device 31 Interrupt Pin Register ................................................ 339 10.1.18 D30IP--Device 30 Interrupt Pin Register ................................................ 339 10.1.19 D29IP--Device 29 Interrupt Pin Register ................................................ 340 10.1.20 D28IP--Device 28 Interrupt Pin Register ................................................ 340 10.1.21 D27IP--Device 27 Interrupt Pin Register ................................................ 341 10.1.22 D26IP--Device 26 Interrupt Pin Register ................................................ 342 10.1.23 D25IP--Device 25 Interrupt Pin Register ................................................ 342 10.1.24 D22IP--Device 22 Interrupt Pin Register ................................................ 342 10.1.25 D20IP--Device 20 Interrupt Pin Register ................................................ 343 10.1.26 D31IR--Device 31 Interrupt Route Register ............................................ 343 10.1.27 D30IR--Device 30 Interrupt Route Register ............................................ 344 10.1.28 D29IR--Device 29 Interrupt Route Register ............................................ 344 10.1.29 D28IR--Device 28 Interrupt Route Register ............................................ 345 10.1.30 D27IR--Device 27 Interrupt Route Register ............................................ 346 10.1.31 D26IR--Device 26 Interrupt Route Register ............................................ 347 10.1.32 D25IR--Device 25 Interrupt Route Register ............................................ 348 10.1.33 D22IR--Device 22 Interrupt Route Register ............................................ 349 10.1.34 D20IR--Device 20 Interrupt Route Register ............................................ 350 10.1.35 OIC--Other Interrupt Control Register.................................................... 351 10.1.36 WADT_AC--Wake Alarm Device Timer - AC Register ................................ 351 10.1.37 WADT_DC--Wake Alarm Device Timer - DC Register ............................... 351 10.1.38 WADT_EXP_AC--Wake Alarm Device Expired Timer - AC Register............................................................................................. 352 10.1.39 WADT_EXP_DC--Wake Alarm Device Expired Timer - DC Register............................................................................................. 352 10.1.40 PRSTS--Power and Reset Status Register ............................................... 352 Datasheet 9 10.1.41 10.1.42 10.1.43 10.1.44 10.1.45 10.1.46 10.1.47 10.1.48 10.1.49 10.1.50 10.1.51 10.1.52 10.1.53 10.1.54 PM_CFG--Power Management Configuration Register ............................... 353 DEEP_S3_POL--Deep Sx From S3 Power Policies Register ......................... 355 DEEP_S4_POL--Deep Sx From S4 Power Policies Register ......................... 355 DEEP_S5_POL--Deep Sx From S5 Power Policies Register ......................... 355 DSX_CFG--Deep Sx Configuration Register ............................................. 356 PMSYNC_CFG--PMSYNC Configuration .................................................... 356 RC--RTC Configuration Register............................................................. 357 HPTC--High Precision Timer Configuration Register .................................. 357 GCS--General Control and Status Register .............................................. 358 BUC--Backed Up Control Register .......................................................... 359 FD--Function Disable Register ............................................................... 359 CG--Clock Gating Register .................................................................... 361 FDSW--Function Disable SUS Well Register ............................................. 362 DISPBDF--Display Bus, Device and Function Initialization Register ........................................................................... 362 10.1.55 FD2--Function Disable 2 Register........................................................... 362 11 10 Gigabit LAN Configuration Registers ...................................................................... 363 11.1 Gigabit LAN Configuration Registers (Gigabit LAN--D25:F0) ..................................................................................... 363 11.1.1 VID--Vendor Identification Register (Gigabit LAN--D25:F0) ......................................................................... 364 11.1.2 DID--Device Identification Register (Gigabit LAN--D25:F0) ......................................................................... 364 11.1.3 PCICMD--PCI Command Register (Gigabit LAN--D25:F0) ......................................................................... 365 11.1.4 PCISTS--PCI Status Register (Gigabit LAN--D25:F0) ......................................................................... 365 11.1.5 RID--Revision Identification Register (Gigabit LAN--D25:F0) ......................................................................... 366 11.1.6 CC--Class Code Register (Gigabit LAN--D25:F0) ......................................................................... 366 11.1.7 CLS--Cache Line Size Register (Gigabit LAN--D25:F0) ......................................................................... 367 11.1.8 PLT--Primary Latency Timer Register (Gigabit LAN--D25:F0) ......................................................................... 367 11.1.9 HEADTYP--Header Type Register (Gigabit LAN--D25:F0) ......................................................................... 367 11.1.10 MBARA--Memory Base Address Register A (Gigabit LAN--D25:F0) ......................................................................... 367 11.1.11 MBARB--Memory Base Address Register B (Gigabit LAN--D25:F0) ......................................................................... 368 11.1.12 MBARC--Memory Base Address Register C (Gigabit LAN--D25:F0) ......................................................................... 368 11.1.13 SVID--Subsystem Vendor ID Register (Gigabit LAN--D25:F0) ......................................................................... 368 11.1.14 SID--Subsystem ID Register (Gigabit LAN--D25:F0) ......................................................................... 369 11.1.15 ERBA--Expansion ROM Base Address Register (Gigabit LAN--D25:F0) ......................................................................... 369 11.1.16 CAPP--Capabilities List Pointer Register (Gigabit LAN--D25:F0) ......................................................................... 369 11.1.17 INTR--Interrupt Information Register (Gigabit LAN--D25:F0) ......................................................................... 369 11.1.18 MLMG--Maximum Latency / Minimum Grant Register (Gigabit LAN--D25:F0) ......................................................................... 369 11.1.19 STCL--System Time Control Low Register (Gigabit LAN--D25:F0) ......................................................................... 370 11.1.20 STCH--System Time Control High Register (Gigabit LAN--D25:F0) ......................................................................... 370 11.1.21 LTRCAP--System Time Control High Register (Gigabit LAN--D25:F0) ......................................................................... 370 11.1.22 CLIST1--Capabilities List Register 1 (Gigabit LAN--D25:F0) ......................................................................... 371 11.1.23 PMC--PCI Power Management Capabilities Register (Gigabit LAN--D25:F0) ......................................................................... 371 Datasheet 11.2 12 11.1.24 PMCS--PCI Power Management Control and Status Register (Gigabit LAN--D25:F0) ............................................................ 371 11.1.25 DR--Data Register (Gigabit LAN--D25:F0) ........................................................................ 372 11.1.26 CLIST2--Capabilities List Register 2 (Gigabit LAN--D25:F0) ........................................................................ 372 11.1.27 MCTL--Message Control Register (Gigabit LAN--D25:F0) ........................................................................ 373 11.1.28 MADDL--Message Address Low Register (Gigabit LAN--D25:F0) ........................................................................ 373 11.1.29 MADDH--Message Address High Register (Gigabit LAN--D25:F0) ........................................................................ 373 11.1.30 MDAT--Message Data Register (Gigabit LAN--D25:F0) ........................................................................ 373 11.1.31 FLRCAP--Function Level Reset Capability (Gigabit LAN--D25:F0) ........................................................................ 374 11.1.32 FLRCLV--Function Level Reset Capability Length and Version Register (Gigabit LAN--D25:F0) ................................................. 374 11.1.33 DEVCTRL--Device Control Register (Gigabit LAN--D25:F0) ....................... 375 Gigabit LAN Capabilities and Status Registers (CSR)............................................. 375 11.2.1 GBECSR_00--Gigabit Ethernet Capabilities and Status Register 00............. 376 11.2.2 GBECSR_18--Gigabit Ethernet Capabilities and Status Register 18............. 376 11.2.3 GBECSR_20--Gigabit Ethernet Capabilities and Status Register 20............. 376 11.2.4 GBECSR_F00--Gigabit Ethernet Capabilities and Status Register F00 ......... 377 11.2.5 GBECSR_F10--Gigabit Ethernet Capabilities and Status Register F10 ......... 377 11.2.6 GBECSR_5400--Gigabit Ethernet Capabilities and Status Register 5400...... 377 11.2.7 GBECSR_5404--Gigabit Ethernet Capabilities and Status Register 5404...... 377 11.2.8 GBECSR_5800--Gigabit Ethernet Capabilities and Status Register 5800...... 378 11.2.9 GBECSR_5B54--Gigabit Ethernet Capabilities and Status Register 5B54 ..... 378 LPC Interface Bridge Registers (D31:F0) ............................................................... 379 12.1 PCI Configuration Registers (LPC I/F--D31:F0) .................................................... 379 12.1.1 VID--Vendor Identification Register (LPC I/F--D31:F0)............................. 380 12.1.2 DID--Device Identification Register (LPC I/F--D31:F0) ............................. 380 12.1.3 PCICMD--PCI COMMAND Register (LPC I/F--D31:F0) ............................... 380 12.1.4 PCISTS--PCI Status Register (LPC I/F--D31:F0) ...................................... 381 12.1.5 RID--Revision Identification Register (LPC I/F--D31:F0) ........................... 382 12.1.6 PI--Programming Interface Register (LPC I/F--D31:F0)............................ 382 12.1.7 SCC--Sub Class Code Register (LPC I/F--D31:F0) ................................... 382 12.1.8 BCC--Base Class Code Register (LPC I/F--D31:F0) .................................. 382 12.1.9 PLT--Primary Latency Timer Register (LPC I/F--D31:F0) .......................... 382 12.1.10 HEADTYP--Header Type Register (LPC I/F--D31:F0) ................................ 382 12.1.11 SS--Sub System Identifiers Register (LPC I/F--D31:F0) ........................... 383 12.1.12 CAPP--Capability List Pointer Register (LPC I/F--D31:F0) ......................... 383 12.1.13 PMBASE--ACPI Base Address Register (LPC I/F--D31:F0) ......................... 383 12.1.14 ACPI_CNTL--ACPI Control Register (LPC I/F--D31:F0) ............................. 384 12.1.15 GPIOBASE--GPIO Base Address Register (LPC I/F--D31:F0) ..................... 384 12.1.16 GC--GPIO Control Register (LPC I/F--D31:F0) ........................................ 385 12.1.17 PIRQ[n]_ROUT--PIRQ[A,B,C,D] Routing Control Register (LPC I/F--D31:F0)............................................................................... 385 12.1.18 SIRQ_CNTL--Serial IRQ Control Register (LPC I/F--D31:F0)............................................................................... 386 12.1.19 PIRQ[n]_ROUT--PIRQ[E,F,G,H] Routing Control Register (LPC I/F--D31:F0)............................................................................... 386 12.1.20 LPC_IBDF--IOxAPIC Bus:Device:Function (LPC I/F--D31:F0)............................................................................... 387 12.1.21 LPC_HnBDF--HPET n Bus:Device:Function (LPC I/F--D31:F0)............................................................................... 387 12.1.22 LPC_I/O_DEC--I/O Decode Ranges Register (LPC I/F--D31:F0)............................................................................... 388 12.1.23 LPC_EN--LPC I/F Enables Register (LPC I/F--D31:F0) .............................. 388 12.1.24 GEN1_DEC--LPC I/F Generic Decode Range 1 Register (LPC I/F--D31:F0)............................................................................... 389 12.1.25 GEN2_DEC--LPC I/F Generic Decode Range 2 Register (LPC I/F--D31:F0)............................................................................... 390 12.1.26 GEN3_DEC--LPC I/F Generic Decode Range 3 Register (LPC I/F--D31:F0)............................................................................... 390 Datasheet 11 12.2 12.3 12.4 12.5 12 12.1.27 GEN4_DEC--LPC I/F Generic Decode Range 4 Register (LPC I/F--D31:F0) ............................................................................... 391 12.1.28 ULKMC--USB Legacy Keyboard / Mouse Control Register(LPC I/F--D31:F0)......................................................... 391 12.1.29 LGMR--LPC I/F Generic Memory Range Register (LPC I/F--D31:F0) ............................................................................... 392 12.1.30 BIOS_SEL1--BIOS Select 1 Register (LPC I/F--D31:F0) ............................................................................... 393 12.1.31 BIOS_SEL2--BIOS Select 2 Register (LPC I/F--D31:F0) ............................................................................... 394 12.1.32 BIOS_DEC_EN1--BIOS Decode Enable Register (LPC I/F--D31:F0)................................................................... 394 12.1.33 BIOS_CNTL--BIOS Control Register (LPC I/F--D31:F0) ............................................................................... 396 12.1.34 FDCAP--Feature Detection Capability ID Register (LPC I/F--D31:F0) ............................................................................... 396 12.1.35 FDLEN--Feature Detection Capability Length Register (LPC I/F--D31:F0) ............................................................................... 397 12.1.36 FDVER--Feature Detection Version Register (LPC I/F--D31:F0) ............................................................................... 397 12.1.37 FVECIDX--Feature Vector Index Register (LPC I/F--D31:F0) ............................................................................... 397 12.1.38 FVECD--Feature Vector Data Register (LPC I/F--D31:F0) ............................................................................... 397 12.1.39 Feature Vector Space ........................................................................... 398 12.1.39.1 FVEC0--Feature Vector Register 0............................................ 398 12.1.39.2 FVEC1--Feature Vector Register 1............................................ 399 12.1.39.3 FVEC2--Feature Vector Register 2............................................ 399 12.1.39.4 FVEC3--Feature Vector Register 3............................................ 399 12.1.40 RCBA--Root Complex Base Address Register (LPC I/F--D31:F0) ............................................................................... 400 DMA I/O Registers ........................................................................................... 400 12.2.1 DMABASE_CA--DMA Base and Current Address Registers ......................... 401 12.2.2 DMABASE_CC--DMA Base and Current Count Registers ............................ 402 12.2.3 DMAMEM_LP--DMA Memory Low Page Registers ...................................... 402 12.2.4 DMACMD--DMA Command Register........................................................ 403 12.2.5 DMASTA--DMA Status Register.............................................................. 403 12.2.6 DMA_WRSMSK--DMA Write Single Mask Register..................................... 404 12.2.7 DMACH_MODE--DMA Channel Mode Register .......................................... 404 12.2.8 DMA Clear Byte Pointer Register ............................................................ 405 12.2.9 DMA Master Clear Register.................................................................... 405 12.2.10 DMA_CLMSK--DMA Clear Mask Register ................................................. 405 12.2.11 DMA_WRMSK--DMA Write All Mask Register............................................ 406 Timer I/O Registers.......................................................................................... 406 12.3.1 TCW--Timer Control Word Register ........................................................ 407 12.3.2 SBYTE_FMT--Interval Timer Status Byte Format Register.......................... 409 12.3.3 Counter Access Ports Register ............................................................... 409 8259 Interrupt Controller (PIC) Registers ............................................................ 410 12.4.1 Interrupt Controller I/O MAP ................................................................. 410 12.4.2 ICW1--Initialization Command Word 1 Register ....................................... 410 12.4.3 ICW2--Initialization Command Word 2 Register ....................................... 411 12.4.4 ICW3--Master Controller Initialization Command Word 3 Register .................................................................................. 412 12.4.5 ICW3--Slave Controller Initialization Command Word 3 Register .................................................................................. 412 12.4.6 ICW4--Initialization Command Word 4 Register ....................................... 412 12.4.7 OCW1--Operational Control Word 1 (Interrupt Mask) Register ............................................................................................. 413 12.4.8 OCW2--Operational Control Word 2 Register ........................................... 413 12.4.9 OCW3--Operational Control Word 3 Register ........................................... 414 12.4.10 ELCR1--Master Controller Edge/Level Triggered Register .......................... 415 12.4.11 ELCR2--Slave Controller Edge/Level Triggered Register ............................ 416 Advanced Programmable Interrupt Controller (APIC) ............................................ 417 12.5.1 APIC Register Map ............................................................................... 417 12.5.2 IND--Index Register ............................................................................ 417 12.5.3 DAT--Data Register ............................................................................. 418 12.5.4 EOIR--EOI Register ............................................................................. 418 Datasheet 12.5.5 ID--Identification Register.................................................................... 419 12.5.6 VER--Version Register ......................................................................... 419 12.5.7 REDIR_TBL--Redirection Table Register ................................................. 420 12.6 Real Time Clock Registers................................................................................. 421 12.6.1 I/O Register Address Map..................................................................... 421 12.6.2 Indexed Registers ............................................................................... 422 12.6.2.1 RTC_REGA--Register A .......................................................... 423 12.6.2.2 RTC_REGB--Register B (General Configuration) ........................ 424 12.6.2.3 RTC_REGC--Register C (Flag Register)..................................... 425 12.6.2.4 RTC_REGD--Register D (Flag Register) .................................... 425 12.7 Processor Interface Registers ............................................................................ 425 12.7.1 NMI_SC--NMI Status and Control Register.............................................. 426 12.7.2 NMI_EN--NMI Enable (and Real Time Clock Index) Register............................................................................................. 426 12.7.3 PORT92--Init Register ......................................................................... 427 12.7.4 COPROC_ERR--Coprocessor Error Register ............................................. 427 12.7.5 RST_CNT--Reset Control Register ......................................................... 427 12.8 Power Management Registers ........................................................................... 428 12.8.1 Power Management PCI Configuration Registers (PM--D31:F0)..................................................................................... 428 12.8.1.1 GEN_PMCON_1--General PM Configuration 1 Register (PM--D31:F0)....................................................................... 428 12.8.1.2 GEN_PMCON_2--General PM Configuration 2 Register (PM--D31:F0)....................................................................... 430 12.8.1.3 GEN_PMCON_3--General PM Configuration 3 Register (PM--D31:F0)....................................................................... 431 12.8.1.4 GEN_PMCON_LOCK--General Power Management Configuration Lock Register ....................................................................... 434 12.8.1.5 BM_BREAK_EN_2 Register #2 (PM--D31:F0) ............................ 434 12.8.1.6 BM_BREAK_EN Register (PM--D31:F0)..................................... 435 12.8.1.7 GPI_ROUT--GPI Routing Control Register (PM--D31:F0)....................................................................... 436 12.8.1.8 GPI_ROUT2--GPI Routing Control Register #2 (PM-D31:F0) ....... 437 12.8.2 APM I/O Decode Register ..................................................................... 437 12.8.2.1 APM_CNT--Advanced Power Management Control Port Register... 437 12.8.2.2 APM_STS--Advanced Power Management Status Port Register .... 438 12.8.3 Power Management I/O Registers.......................................................... 438 12.8.3.1 PM1_STS--Power Management 1 Status Register ...................... 439 12.8.3.2 PM1_EN--Power Management 1 Enable Register........................ 440 12.8.3.3 PM1_CNT--Power Management 1 Control Register ..................... 441 12.8.3.4 PM1_TMR--Power Management 1 Timer Register ....................... 442 12.8.3.5 GPE0_STS--General Purpose Event 0 Status Register ................ 442 12.8.3.6 GPE0_EN--General Purpose Event 0 Enables Register ................ 445 12.8.3.7 SMI_EN--SMI Control and Enable Register................................ 446 12.8.3.8 SMI_STS--SMI Status Register ............................................... 448 12.8.3.9 ALT_GPI_SMI_EN--Alternate GPI SMI Enable Register ............... 450 12.8.3.10 ALT_GPI_SMI_STS--Alternate GPI SMI Status Register .............. 450 12.8.3.11 GPE_CNTL--General Purpose Control Register ........................... 450 12.8.3.12 DEVACT_STS--Device Activity Status Register .......................... 451 12.8.3.13 PM2_CNT--Power Management 2 Control Register ..................... 452 12.8.3.14 ALT_GPI_SMI_EN2--Alternate GPI SMI Enable 2 Register ........... 452 12.8.3.15 ALT_GPI_SMI_STS2--Alternate GPI SMI Status 2 Register.......... 452 12.9 System Management TCO Registers................................................................... 453 12.9.1 TCO_RLD--TCO Timer Reload and Current Value Register ......................... 454 12.9.2 TCO_DAT_IN--TCO Data In Register...................................................... 454 12.9.3 TCO_DAT_OUT--TCO Data Out Register ................................................. 454 12.9.4 TCO1_STS--TCO1 Status Register ......................................................... 454 12.9.5 TCO2_STS--TCO2 Status Register ......................................................... 455 12.9.6 TCO1_CNT--TCO1 Control Register........................................................ 456 12.9.7 TCO2_CNT--TCO2 Control Register........................................................ 457 12.9.8 TCO_MESSAGE1 and TCO_MESSAGE2 Registers...................................... 458 12.9.9 TCO_WDCNT--TCO Watchdog Control Register........................................ 458 12.9.10 SW_IRQ_GEN--Software IRQ Generation Register ................................... 458 12.9.11 TCO_TMR--TCO Timer Initial Value Register ........................................... 458 12.10 General Purpose I/O Registers .......................................................................... 459 12.10.1 GPIO_USE_SEL--GPIO Use Select Register ............................................. 460 12.10.2 GP_IO_SEL--GPIO Input/Output Select Register...................................... 460 Datasheet 13 12.10.3 12.10.4 12.10.5 12.10.6 GP_LVL--GPIO Level for Input or Output Register .................................... 460 GPO_BLINK--GPO Blink Enable Register ................................................. 461 GP_SER_BLINK--GP Serial Blink Register ................................................ 461 GP_SB_CMDSTS--GP Serial Blink Command Status Register ................................................................................... 462 12.10.7 GP_SB_DATA--GP Serial Blink Data Register ........................................... 462 12.10.8 GPI_NMI_EN--GPI NMI Enable Register .................................................. 462 12.10.9 GPI_NMI_STS--GPI NMI Status Register ................................................. 463 12.10.10GPI_INV--GPIO Signal Invert Register.................................................... 463 12.10.11GPIO_USE_SEL2--GPIO Use Select 2 Register ......................................... 464 12.10.12GP_IO_SEL2--GPIO Input/Output Select 2 Register ................................. 464 12.10.13GP_LVL2--GPIO Level for Input or Output 2 Register................................ 465 12.10.14GPIO_USE_SEL3--GPIO Use Select 3 Register ......................................... 465 12.10.15GP_IO_SEL3--GPIO Input/Output Select 3 Register ................................. 466 12.10.16GP_LVL3--GPIO Level for Input or Output 3 Register................................ 466 12.10.17GP_RST_SEL1--GPIO Reset Select Register ............................................ 466 12.10.18GP_RST_SEL2--GPIO Reset Select Register ............................................ 467 12.10.19GP_RST_SEL3--GPIO Reset Select Register ............................................ 467 13 14 SATA Controller Registers (D31:F2) ....................................................................... 468 13.1 PCI Configuration Registers (SATA-D31:F2) ........................................................ 468 13.1.1 VID--Vendor Identification Register (SATA--D31:F2)................................ 469 13.1.2 DID--Device Identification Register (SATA--D31:F2) ................................ 470 13.1.3 PCICMD--PCI Command Register (SATA-D31:F2) .................................... 470 13.1.4 PCISTS--PCI Status Register (SATA-D31:F2) .......................................... 471 13.1.5 RID--Revision Identification Register (SATA--D31:F2) .............................. 471 13.1.6 PI--Programming Interface Register (SATA-D31:F2) ................................ 472 13.1.6.1 When Sub Class Code Register (D31:F2:Offset 0Ah) = 01h ......... 472 13.1.6.2 When Sub Class Code Register (D31:F2:Offset 0Ah) = 04h ......... 472 13.1.6.3 When Sub Class Code Register (D31:F2:Offset 0Ah) = 06h ......... 472 13.1.7 SCC--Sub Class Code Register (SATA-D31:F2)........................................ 473 13.1.8 BCC--Base Class Code Register (SATA-D31:F2SATA-D31:F2)................................................................ 473 13.1.9 PMLT--Primary Master Latency Timer Register (SATA-D31:F2)................................................................................... 473 13.1.10 HTYPE--Header Type Register (SATA-D31:F2)................................................................................... 473 13.1.11 PCMD_BAR--Primary Command Block Base Address Register (SATA-D31:F2) ...................................................................... 474 13.1.12 PCNL_BAR--Primary Control Block Base Address Register (SATA-D31:F2)................................................................................... 474 13.1.13 SCMD_BAR--Secondary Command Block Base Address Register (SATA D31:F2) ....................................................................... 474 13.1.14 SCNL_BAR--Secondary Control Block Base Address Register (SATA D31:F2) ....................................................................... 475 13.1.15 BAR--Legacy Bus Master Base Address Register (SATA-D31:F2)................................................................................... 475 13.1.16 ABAR/SIDPBA1--AHCI Base Address Register / Serial ATA Index Data Pair Base Address (SATA-D31:F2)......................................... 475 13.1.16.1 When SCC is not 01h ............................................................. 476 13.1.16.2 When SCC is 01h................................................................... 476 13.1.17 SVID--Subsystem Vendor Identification Register (SATA-D31:F2)................................................................................... 476 13.1.18 SID--Subsystem Identification Register (SATA-D31:F2) ........................... 477 13.1.19 CAP--Capabilities Pointer Register (SATA-D31:F2) ................................... 477 13.1.20 INT_LN--Interrupt Line Register (SATA-D31:F2) ..................................... 477 13.1.21 INT_PN--Interrupt Pin Register (SATA-D31:F2) ....................................... 477 13.1.22 IDE_TIM--IDE Timing Register (SATA-D31:F2)........................................ 478 13.1.23 SIDETIM--Slave IDE Timing Register (SATA-D31:F2) ............................... 478 13.1.24 SDMA_CNT--Synchronous DMA Control Register (SATA-D31:F2)................................................................................... 478 13.1.25 SDMA_TIM--Synchronous DMA Timing Register (SATA-D31:F2)................................................................................... 479 13.1.26 IDE_CONFIG--IDE I/O Configuration Register (SATA-D31:F2)................................................................................... 479 13.1.27 PID--PCI Power Management Capability Identification Register (SATA-D31:F2) ...................................................................... 479 Datasheet 13.2 13.3 13.4 Datasheet 13.1.28 PC--PCI Power Management Capabilities Register (SATA-D31:F2) .................................................................................. 480 13.1.29 PMCS--PCI Power Management Control and Status Register (SATA-D31:F2) ...................................................................... 480 13.1.30 MSICI--Message Signaled Interrupt Capability Identification Register (SATA-D31:F2) ................................................... 481 13.1.31 MSIMC--Message Signaled Interrupt Message Control Register (SATA-D31:F2) ........................................................... 481 13.1.32 MSIMA--Message Signaled Interrupt Message Address Register (SATA-D31:F2) .......................................................... 482 13.1.33 MSIMD--Message Signaled Interrupt Message Data Register (SATA-D31:F2)............................................................... 483 13.1.34 MAP--Address Map Register (SATA-D31:F2) ........................................... 483 13.1.35 PCS--Port Control and Status Register (SATA-D31:F2) ............................ 483 13.1.36 SCLKCG--SATA Clock Gating Control Register ......................................... 486 13.1.37 SGC--SATA General Configuration Register............................................. 486 13.1.38 SATACR0--SATA Capability Register 0 (SATA-D31:F2) ............................. 487 13.1.39 SATACR1--SATA Capability Register 1 (SATA-D31:F2) ............................. 487 13.1.40 FLRCID--FLR Capability Identification Register (SATA-D31:F2) ................. 488 13.1.41 FLRCLV--FLR Capability Length and Version Register (SATA-D31:F2)......... 488 13.1.42 FLRC--FLR Control Register (SATA-D31:F2) ........................................... 488 13.1.43 ATC--APM Trapping Control Register (SATA-D31:F2) ............................... 489 13.1.44 ATS--APM Trapping Status Register (SATA-D31:F2) ................................ 489 13.1.45 SP--Scratch Pad Register (SATA-D31:F2) .............................................. 489 13.1.46 BFCS--BIST FIS Control/Status Register (SATA-D31:F2) .......................... 489 13.1.47 BFTD1--BIST FIS Transmit Data1 Register (SATA-D31:F2)....................... 491 13.1.48 BFTD2--BIST FIS Transmit Data2 Register (SATA-D31:F2)....................... 491 Bus Master IDE I/O Registers (D31:F2) .............................................................. 492 13.2.1 BMIC[P,S]--Bus Master IDE Command Register (D31:F2) ......................... 493 13.2.2 BMIS[P,S]--Bus Master IDE Status Register (D31:F2) .............................. 493 13.2.3 BMID[P,S]--Bus Master IDE Descriptor Table Pointer Register (D31:F2) ............................................................................... 494 13.2.4 AIR--AHCI Index Register (D31:F2)....................................................... 494 13.2.5 AIDR--AHCI Index Data Register (D31:F2) ............................................. 495 Serial ATA Index/Data Pair Superset Registers .................................................... 495 13.3.1 SINDX--Serial ATA Index Register (D31:F2) ........................................... 495 13.3.2 SDATA--Serial ATA Data Register (D31:F2) ............................................ 496 13.3.2.1 PxSSTS--Serial ATA Status Register (D31:F2)........................... 496 13.3.2.2 PxSCTL--Serial ATA Control Register (D31:F2) .......................... 497 13.3.2.3 PxSERR--Serial ATA Error Register (D31:F2) ............................ 498 AHCI Registers (D31:F2) .................................................................................. 499 13.4.1 AHCI Generic Host Control Registers (D31:F2) ........................................ 500 13.4.1.1 CAP--Host Capabilities Register (D31:F2) ................................. 500 13.4.1.2 GHC--Global PCH Control Register (D31:F2) ............................. 501 13.4.1.3 IS--Interrupt Status Register (D31:F2) .................................... 502 13.4.1.4 PI--Ports Implemented Register (D31:F2) ................................ 503 13.4.1.5 VS--AHCI Version Register (D31:F2) ....................................... 504 13.4.1.6 EM_LOC--Enclosure Management Location Register (D31:F2) ..... 504 13.4.1.7 EM_CTRL--Enclosure Management Control Register (D31:F2) ..... 504 13.4.1.8 CAP2--HBA Capabilities Extended Register ............................... 505 13.4.1.9 RSTF--Intel(R) RST Feature Capabilities Register......................... 506 13.4.2 Port Registers (D31:F2) ....................................................................... 507 13.4.2.1 PxCLB--Port [5:0] Command List Base Address Register (D31:F2) ............................................................................. 509 13.4.2.2 PxCLBU--Port [5:0] Command List Base Address Upper 32-Bits Register (D31:F2) ...................................................... 510 13.4.2.3 PxFB--Port [5:0] FIS Base Address Register (D31:F2)................ 510 13.4.2.4 PxFBU--Port [5:0] FIS Base Address Upper 32-Bits Register (D31:F2) ................................................................. 510 13.4.2.5 PxIS--Port [5:0] Interrupt Status Register (D31:F2) .................. 511 13.4.2.6 PxIE--Port [5:0] Interrupt Enable Register (D31:F2).................. 512 13.4.2.7 PxCMD--Port [5:0] Command Register (D31:F2) ....................... 513 13.4.2.8 PxTFD--Port [5:0] Task File Data Register (D31:F2) .................. 515 13.4.2.9 PxSIG--Port [5:0] Signature Register (D31:F2)......................... 516 13.4.2.10 PxSSTS--Port [5:0] Serial ATA Status Register (D31:F2) ............ 516 13.4.2.11 PxSCTL--Port [5:0] Serial ATA Control Register (D31:F2) ........... 517 13.4.2.12 PxSERR--Port [5:0] Serial ATA Error Register (D31:F2).............. 518 15 13.4.2.13 PxSACT--Port [5:0] Serial ATA Active Register (D31:F2)............. 519 13.4.2.14 PxCI--Port [5:0] Command Issue Register (D31:F2) .................. 520 14 16 SATA Controller Registers (D31:F5) ....................................................................... 521 14.1 PCI Configuration Registers (SATA-D31:F5) ........................................................ 521 14.1.1 VID--Vendor Identification Register (SATA--D31:F5)................................ 522 14.1.2 DID--Device Identification Register (SATA--D31:F5) ................................ 522 14.1.3 PCICMD--PCI Command Register (SATA-D31:F5) .................................... 522 14.1.4 PCISTS--PCI Status Register (SATA-D31:F5) .......................................... 523 14.1.5 RID--Revision Identification Register (SATA--D31:F5) .............................. 524 14.1.6 PI--Programming Interface Register (SATA-D31:F5) ................................ 524 14.1.7 SCC--Sub Class Code Register (SATA-D31:F5)........................................ 524 14.1.8 BCC--Base Class Code Register (SATA-D31:F5SATA-D31:F5)................................................................ 525 14.1.9 PCMD_BAR--Primary Command Block Base Address Register (SATA-D31:F5) ...................................................................... 525 14.1.10 PCNL_BAR--Primary Control Block Base Address Register (SATA-D31:F5)................................................................................... 525 14.1.11 SCMD_BAR--Secondary Command Block Base Address Register (SATA D31:F5) ....................................................................... 526 14.1.12 SCNL_BAR--Secondary Control Block Base Address Register (SATA D31:F5) ....................................................................... 526 14.1.13 BAR--Legacy Bus Master Base Address Register (SATA-D31:F5)................................................................................... 526 14.1.14 SIDPBA--SATA Index/Data Pair Base Address Register (SATA-D31:F5)................................................................................... 527 14.1.15 SVID--Subsystem Vendor Identification Register (SATA-D31:F5)................................................................................... 527 14.1.16 SID--Subsystem Identification Register (SATA-D31:F5) ........................... 527 14.1.17 CAP--Capabilities Pointer Register (SATA-D31:F5) ................................... 527 14.1.18 INT_LN--Interrupt Line Register (SATA-D31:F5) ..................................... 528 14.1.19 INT_PN--Interrupt Pin Register (SATA-D31:F5) ....................................... 528 14.1.20 IDE_TIM--IDE Timing Register (SATA-D31:F5)........................................ 528 14.1.21 SDMA_CNT--Synchronous DMA Control Register (SATA-D31:F5)................................................................................... 528 14.1.22 SDMA_TIM--Synchronous DMA Timing Register (SATA-D31:F5)................................................................................... 529 14.1.23 IDE_CONFIG--IDE I/O Configuration Register (SATA-D31:F5)................................................................................... 529 14.1.24 PID--PCI Power Management Capability Identification Register (SATA-D31:F5) ...................................................................... 530 14.1.25 PC--PCI Power Management Capabilities Register (SATA-D31:F5)................................................................................... 530 14.1.26 PMCS--PCI Power Management Control and Status Register (SATA-D31:F5) ...................................................................... 530 14.1.27 MAP--Address Map Register (SATA-D31:F5) ........................................... 531 14.1.28 PCS--Port Control and Status Register (SATA-D31:F5) ............................. 532 14.1.29 SATACR0--SATA Capability Register 0 (SATA-D31:F5) ............................. 532 14.1.30 SATACR1--SATA Capability Register 1 (SATA-D31:F5) ............................. 533 14.1.31 FLRCID--FLR Capability ID Register (SATA-D31:F5)................................. 533 14.1.32 FLRCLV--FLR Capability Length and Value Register (SATA-D31:F5) .............................................................. 533 14.1.33 FLRCTRL--FLR Control Register (SATA-D31:F5)....................................... 534 14.1.34 ATC--APM Trapping Control Register (SATA-D31:F5) ............................... 534 14.1.35 ATC--APM Trapping Control Register (SATA-D31:F5) ............................... 534 14.2 Bus Master IDE I/O Registers (D31:F5)............................................................... 534 14.2.1 BMIC[P,S]--Bus Master IDE Command Register (D31:F5) ......................... 535 14.2.2 BMIS[P,S]--Bus Master IDE Status Register (D31:F5) .............................. 536 14.2.3 BMID[P,S]--Bus Master IDE Descriptor Table Pointer Register (D31:F5)................................................................................ 536 14.3 Serial ATA Index/Data Pair Superset Registers..................................................... 537 14.3.1 SINDX--SATA Index Register (D31:F5)................................................... 537 14.3.2 SDATA--SATA Index Data Register (D31:F5)........................................... 537 14.3.2.1 PxSSTS--Serial ATA Status Register (D31:F5) ........................... 538 14.3.2.2 PxSCTL--Serial ATA Control Register (D31:F5) .......................... 539 14.3.2.3 PxSERR--Serial ATA Error Register (D31:F5) ............................. 540 Datasheet 15 EHCI Controller Registers (D29:F0, D26:F0) .......................................................... 541 15.1 USB EHCI Configuration Registers (USB EHCI--D29:F0, D26:F0) ........................................................................... 541 15.1.1 VID--Vendor Identification Register (USB EHCI--D29:F0, D26:F0) ............................................................... 542 15.1.2 DID--Device Identification Register (USB EHCI--D29:F0, D26:F0) ............................................................... 542 15.1.3 PCICMD--PCI Command Register (USB EHCI--D29:F0, D26:F0) ............................................................... 542 15.1.4 PCISTS--PCI Status Register (USB EHCI--D29:F0, D26:F0) ............................................................... 543 15.1.5 RID--Revision Identification Register (USB EHCI--D29:F0, D26:F0) ............................................................... 544 15.1.6 PI--Programming Interface Register (USB EHCI--D29:F0, D26:F0) ............................................................... 545 15.1.7 SCC--Sub Class Code Register (USB EHCI--D29:F0, D26:F0) ............................................................... 545 15.1.8 BCC--Base Class Code Register (USB EHCI--D29:F0, D26:F0) ............................................................... 545 15.1.9 PMLT--Primary Master Latency Timer Register (USB EHCI--D29:F0, D26:F0) ............................................................... 545 15.1.10 HEADTYP--Header Type Register (USB EHCI--D29:F0, D26:F0) ............................................................... 545 15.1.11 MEM_BASE--Memory Base Address Register (USB EHCI--D29:F0, D26:F0) ............................................................... 546 15.1.12 SVID--USB EHCI Subsystem Vendor ID Register (USB EHCI--D29:F0, D26:F0) ............................................................... 546 15.1.13 SID--USB EHCI Subsystem ID Register (USB EHCI--D29:F0, D26:F0) ............................................................... 546 15.1.14 CAP_PTR--Capabilities Pointer Register (USB EHCI--D29:F0, D26:F0) ............................................................... 547 15.1.15 INT_LN--Interrupt Line Register (USB EHCI--D29:F0, D26:F0) ............................................................... 547 15.1.16 INT_PN--Interrupt Pin Register (USB EHCI--D29:F0, D26:F0) ............................................................... 547 15.1.17 PWR_CAPID--PCI Power Management Capability Identification Register (USB EHCI--D29:F0, D26:F0) ............................... 547 15.1.18 NXT_PTR1--Next Item Pointer #1 Register (USB EHCI--D29:F0, D26:F0) ............................................................... 548 15.1.19 PWR_CAP--Power Management Capabilities Register (USB EHCI--D29:F0, D26:F0) ............................................................... 548 15.1.20 PWR_CNTL_STS--Power Management Control / Status Register (USB EHCI--D29:F0, D26:F0)......................................... 549 15.1.21 DEBUG_CAPID--Debug Port Capability ID Register (USB EHCI--D29:F0, D26:F0) ............................................................... 549 15.1.22 NXT_PTR2--Next Item Pointer #2 Register (USB EHCI--D29:F0, D26:F0) ............................................................... 550 15.1.23 DEBUG_BASE--Debug Port Base Offset Register (USB EHCI--D29:F0, D26:F0) ............................................................... 550 15.1.24 USB_RELNUM--USB Release Number Register (USB EHCI--D29:F0, D26:F0) ............................................................... 550 15.1.25 FL_ADJ--Frame Length Adjustment Register (USB EHCI--D29:F0, D26:F0) ............................................................... 551 15.1.26 PWAKE_CAP--Port Wake Capability Register (USB EHCI--D29:F0, D26:F0) ............................................................... 552 15.1.27 PDO--Port Disable Override Register...................................................... 552 15.1.28 RMHDEVR--RMH Device Removable Field Register ................................... 553 15.1.29 LEG_EXT_CAP--USB EHCI Legacy Support Extended Capability Register (USB EHCI--D29:F0, D26:F0) .................................... 553 15.1.30 LEG_EXT_CS--USB EHCI Legacy Support Extended Control / Status Register (USB EHCI--D29:F0, D26:F0)............................ 554 15.1.31 SPECIAL_SMI--Intel(R) Specific USB 2.0 SMI Register (USB EHCI--D29:F0, D26:F0) ............................................................... 555 15.1.32 OCMAP--Over-Current Mapping Register ................................................ 557 15.1.33 RMHWKCTL--RMH Wake Control Register ............................................... 558 15.1.34 ACCESS_CNTL--Access Control Register (USB EHCI--D29:F0, D26:F0) ............................................................... 558 Datasheet 17 15.2 16 18 15.1.35 EHCIIR1--EHCI Initialization Register 1 (USB EHCI--D29:F0, D26:F0) ............................................................... 559 15.1.36 FLR_CID--Function Level Reset Capability ID Register (USB EHCI--D29:F0, D26:F0) ............................................................... 559 15.1.37 FLR_NEXT--Function Level Reset Next Capability Pointer Register (USB EHCI--D29:F0, D26:F0) ........................................ 559 15.1.38 FLR_CLV--Function Level Reset Capability Length and Version Register (USB EHCI--D29:F0, D26:F0)........................................ 559 15.1.39 FLR_CTRL--Function Level Reset Control Register (USB EHCI--D29:F0, D26:F0) ............................................................... 560 15.1.40 FLR_STS--Function Level Reset Status Register (USB EHCI--D29:F0, D26:F0) ............................................................... 560 Memory-Mapped I/O Registers .......................................................................... 561 15.2.1 Host Controller Capability Registers ....................................................... 561 15.2.1.1 CAPLENGTH--Capability Registers Length Register ..................... 562 15.2.1.2 HCIVERSION--Host Controller Interface Version Number Register ............................................................................... 562 15.2.1.3 HCSPARAMS--Host Controller Structural Parameters .................. 562 15.2.1.4 HCCPARAMS--Host Controller Capability Parameters Register ............................................................................... 563 15.2.2 Host Controller Operational Registers ..................................................... 564 15.2.2.1 USB2.0_CMD--USB 2.0 Command Register ............................... 565 15.2.2.2 USB2.0_STS--USB 2.0 Status Register ..................................... 567 15.2.2.3 USB2.0_INTR--USB 2.0 Interrupt Enable Register...................... 569 15.2.2.4 FRINDEX--Frame Index Register ............................................. 570 15.2.2.5 CTRLDSSEGMENT--Control Data Structure Segment Register ............................................................................... 571 15.2.2.6 PERIODICLISTBASE--Periodic Frame List Base Address Register ............................................................................... 571 15.2.2.7 ASYNCLISTADDR--Current Asynchronous List Address Register ............................................................................... 572 15.2.2.8 CONFIGFLAG--Configure Flag Register ..................................... 572 15.2.2.9 PORTSC--Port N Status and Control Register............................. 572 15.2.3 USB 2.0-Based Debug Port Registers...................................................... 575 15.2.3.1 CNTL_STS--Control / Status Register ....................................... 576 15.2.3.2 USBPID--USB PIDs Register.................................................... 577 15.2.3.3 DATABUF[7:0]--Data Buffer Bytes[7:0] Register ....................... 577 15.2.3.4 CONFIG--Configuration Register .............................................. 578 xHCI Controller Registers (D20:F0)........................................................................ 579 16.1 USB xHCI Configuration Registers (USB xHCI--D20:F0) ........................................................................................ 579 16.1.1 VID--Vendor Identification Register (USB xHCI--D20:F0)............................................................................ 580 16.1.2 DID--Device Identification Register (USB xHCI--D20:F0)............................................................................ 580 16.1.3 PCICMD--PCI Command Register (USB xHCI--D20:F0)............................................................................ 581 16.1.4 PCISTS--PCI Status Register (USB xHCI--D20:F0)............................................................................ 582 16.1.5 RID--Revision Identification Register (USB xHCI--D20:F0)............................................................................ 583 16.1.6 PI--Programming Interface Register (USB xHCI--D20:F0)............................................................................ 583 16.1.7 SCC--Sub Class Code Register (USB xHCI--D20:F0)............................................................................ 583 16.1.8 BCC--Base Class Code Register (USB xHCI--D20:F0)............................................................................ 583 16.1.9 PMLT--Primary Master Latency Timer Register (USB xHCI--D20:F0)............................................................................ 583 16.1.10 HEADTYP--Header Type Register (USB xHCI--D20:F0)............................................................................ 584 16.1.11 MEM_BASE_L--Memory Base Address Low Register (USB xHCI--D20:F0)............................................................................ 584 16.1.12 MEM_BASE_H--Memory Base Address High Register (USB xHCI--D20:F0)............................................................................ 584 Datasheet 16.2 Datasheet 16.1.13 SVID--USB xHCI Subsystem Vendor ID Register (USB xHCI--D20:F0) ........................................................................... 584 16.1.14 SID--USB xHCI Subsystem ID Register (USB xHCI--D20:F0) ........................................................................... 585 16.1.15 CAP_PTR--Capabilities Pointer Register (USB xHCI--D20:F0) ........................................................................... 585 16.1.16 INT_LN--Interrupt Line Register (USB xHCI--D20:F0) ........................................................................... 585 16.1.17 INT_PN--Interrupt Pin Register (USB xHCI--D20:F0) ........................................................................... 585 16.1.18 XHCC--xHC System Bus Configuration Register (USB xHCI--D20:F0) ........................................................................... 585 16.1.19 XHCC2--xHC System Bus Configuration Register 2 (USB xHCI--D20:F0) ........................................................................... 586 16.1.20 SBRN--Serial Bus Release Number Register (USB xHCI--D20:F0) ............................................................... 586 16.1.21 FL_ADJ--Frame Length Adjustment Register (USB xHCI--D20:F0) ........................................................................... 587 16.1.22 PWR_CAPID--PCI Power Management Capability ID Register (USB xHCI--D20:F0) ............................................................... 587 16.1.23 NXT_PTR1--Next Item Pointer #1 Register (USB xHCI--D20:F0) ........................................................................... 588 16.1.24 PWR_CAP--Power Management Capabilities Register (USB xHCI--D20:F0) ........................................................................... 588 16.1.25 PWR_CNTL_STS--Power Management Control / Status Register (USB xHCI--D20:F0) ..................................................... 589 16.1.26 MSI_CAPID--Message Signaled Interrupt Capability ID Register (USB xHCI--D20:F0) ........................................................................... 589 16.1.27 NEXT_PTR2--Next Item Pointer Register #2 (USB xHCI--D20:F0) ........................................................................... 589 16.1.28 MSI_MCTL--MSI Message Control Register (USB xHCI--D20:F0) ........................................................................... 590 16.1.29 MSI_LMAD--MSI Lower Message Address Register (USB xHCI--D20:F0) ........................................................................... 590 16.1.30 MSI_UMAD--MSI Upper Message Address Register (USB xHCI--D20:F0) ........................................................................... 590 16.1.31 MSI_MD--MSI Message Data Register (USB xHCI--D20:F0) ........................................................................... 591 16.1.32 U2OCM1 - XHCI USB2 Overcurrent Mapping Register1 (USB xHCI--D20:F0) ........................................................................... 591 16.1.33 U2OCM2 - XHCI USB2 Overcurrent Mapping Register 2 (USB xHCI--D20:F0) ........................................................................... 591 16.1.34 U3OCM1 - XHCI USB3 Overcurrent Pin Mapping 1 (USB xHCI--D20:F0) ........................................................................... 592 16.1.35 U3OCM2 - XHCI USB3 Overcurrent Pin Mapping 2 (USB xHCI--D20:F0) ........................................................................... 593 16.1.36 XUSB2PR--xHC USB 2.0 Port Routing Register (USB xHCI--D20:F0) ........................................................................... 593 16.1.37 XUSB2PRM--xHC USB 2.0 Port Routing Mask Register (USB xHCI--D20:F0) ........................................................................... 594 16.1.38 USB3_PSSEN--USB 3.0 Port SuperSpeed Enable Register (USB xHCI--D20:F0) ........................................................................... 594 16.1.39 USB3PRM--USB 3.0 Port Routing Mask Register (USB xHCI--D20:F0) ........................................................................... 595 16.1.40 USB2PDO--xHCI USB Port Disable Override Register (USB xHCI--D20:F0) ........................................................................... 595 16.1.41 USB3PDO--USB3 Port Disable Override (USB xHCI--D20:F0) ........................................................................... 596 Memory-Mapped I/O Registers .......................................................................... 596 16.2.1 Host Controller Capability Registers ....................................................... 597 16.2.1.1 CAPLENGTH--Capability Registers Length Register..................... 597 16.2.1.2 HCIVERSION--Host Controller Interface Version Number Register............................................................................... 597 16.2.1.3 HCSPARAMS1--Host Controller Structural Parameters #1 Register597 16.2.1.4 HCSPARAMS2--Host Controller Structural Parameters #2 Register598 16.2.1.5 HCSPARAMS3--Host Controller Structural Parameters #3 Register598 16.2.1.6 HCCPARAMS--Host Controller Capability Parameters Register ..... 599 19 16.2.1.7 dBOFF--Doorbell Offset Register .............................................. 599 16.2.1.8 RTSOFF--Runtime Register Space Offset Register ...................... 600 16.2.2 Host Controller Operational Registers ..................................................... 600 16.2.2.1 USB_CMD--USB Command Register......................................... 601 16.2.2.2 USB_STS--USB Status Register ............................................... 602 16.2.2.3 PAGESIZE--Page Size Register ................................................ 603 16.2.2.4 DNCTRL--Device Notification Control Register ........................... 603 16.2.2.5 CRCRL--Command Ring Control Low Register............................ 604 16.2.2.6 CRCRH--Command Ring Control High Register .......................... 605 16.2.2.7 DCBAAPL--Device Context Base Address Array Pointer Low Register ............................................................................... 605 16.2.2.8 DCBAAPH--Device Context Base Address Array Pointer High Register ............................................................................... 605 16.2.2.9 CONFIG--Configure Register ................................................... 605 16.2.2.10 PORTSCNUSB2--Port N Status and Control USB2 Register........... 606 16.2.2.11 PORTPMSCNUSB2--xHCI Port N Power Management Status and Control USB2 Register............................................................ 610 16.2.2.12 PORTSCNUSB3--xHCI USB 3.0 Port N Status and Control Register611 16.2.2.13 PORTPMSCN--Port N Power Management Status and Control USB3 Register....................................................................... 615 16.2.2.14 PORTLIX--USB 3.0 Port X Link Info Register.............................. 616 16.2.3 Host Controller Runtime Registers.......................................................... 616 16.2.3.1 MFINDEX--Microframe Index Register ...................................... 616 16.2.3.2 IMAN--Interrupter X Management Register ............................... 617 16.2.3.3 IMOD--Interrupter X Moderation Register ................................. 618 16.2.3.4 ERSTSZ--Event Ring Segment Table Size X Register .................. 618 16.2.3.5 ERSTBAL--Event Ring Segment Table Base Address Low X Register ............................................................................... 619 16.2.3.6 ERSTBAH--Event Ring Segment Table Base Address High X Register ............................................................................... 619 16.2.3.7 ERDPL--Event Ring Dequeue Pointer Low X Register .................. 620 16.2.3.8 ERDPH--Event Ring Dequeue Pointer High X Register ................. 620 16.2.4 Doorbell Registers ............................................................................... 620 16.2.4.1 DOORBELL--Doorbell X Register .............................................. 621 17 20 Integrated Intel(R) High Definition Audio (Intel(R) HD Audio) Controller Registers .... 622 17.1 Intel(R) High Definition Audio (Intel(R) HD Audio) Controller Registers (D27:F0) .......... 622 17.1.1 Intel(R) High Definition Audio PCI Configuration Space (Intel(R) High Definition Audio--D27:F0) .................................................. 622 17.1.1.1 VID--Vendor Identification Register (Intel(R) High Definition Audio Controller--D27:F0) ...................... 624 17.1.1.2 DID--Device Identification Register (Intel(R) High Definition Audio Controller--D27:F0) ...................... 624 17.1.1.3 PCICMD--PCI Command Register (Intel(R) High Definition Audio Controller--D27:F0) ...................... 624 17.1.1.4 PCISTS--PCI Status Register (Intel(R) High Definition Audio Controller--D27:F0) ...................... 625 17.1.1.5 RID--Revision Identification Register (Intel(R) High Definition Audio Controller--D27:F0) ...................... 625 17.1.1.6 PI--Programming Interface Register (Intel(R) High Definition Audio Controller--D27:F0) ...................... 626 17.1.1.7 SCC--Sub Class Code Register (Intel(R) High Definition Audio Controller--D27:F0) ...................... 626 17.1.1.8 BCC--Base Class Code Register (Intel(R) High Definition Audio Controller--D27:F0) ...................... 626 17.1.1.9 CLS--Cache Line Size Register (Intel(R) High Definition Audio Controller--D27:F0) ...................... 626 17.1.1.10 LT--Latency Timer Register (Intel(R) High Definition Audio Controller--D27:F0) ...................... 626 17.1.1.11 HEADTYP--Header Type Register (Intel(R) High Definition Audio Controller--D27:F0) ...................... 627 17.1.1.12 HdBARL--Intel(R) High Definition Audio Lower Base Address Register (Intel(R) High Definition Audio--D27:F0) ........................ 627 17.1.1.13 HdBARU--Intel(R) High Definition Audio Upper Base Address Register (Intel(R) High Definition Audio Controller--D27:F0).......... 627 17.1.1.14 SVID--Subsystem Vendor Identification Register (Intel(R) High Definition Audio Controller--D27:F0) ...................... 627 Datasheet 17.1.1.15 SID--Subsystem Identification Register (Intel(R) High Definition Audio Controller--D27:F0) ..................... 628 17.1.1.16 CAPPTR--Capabilities Pointer Register (Intel(R) High Definition Audio Controller--D27:F0) ..................... 628 17.1.1.17 INTLN--Interrupt Line Register (Intel(R) High Definition Audio Controller--D27:F0) ..................... 628 17.1.1.18 INTPN--Interrupt Pin Register (Intel(R) High Definition Audio Controller--D27:F0) ..................... 628 17.1.1.19 HDCTL--Intel(R) High Definition Audio Control Register (Intel(R) High Definition Audio Controller--D27:F0) ..................... 629 17.1.1.20 DCKCTL--Docking Control Register (Mobile Only) (Intel(R) High Definition Audio Controller--D27:F0) ..................... 629 17.1.1.21 DCKSTS--Docking Status Register (Mobile Only) (Intel(R) High Definition Audio Controller--D27:F0) ..................... 629 17.1.1.22 PID--PCI Power Management Capability ID Register (Intel(R) High Definition Audio Controller--D27:F0) ..................... 630 17.1.1.23 PC--Power Management Capabilities Register (Intel(R) High Definition Audio Controller--D27:F0) ..................... 630 17.1.1.24 PCS--Power Management Control and Status Register (Intel(R) High Definition Audio Controller--D27:F0) ..................... 630 17.1.1.25 MID--MSI Capability ID Register (Intel(R) High Definition Audio Controller--D27:F0) ..................... 631 17.1.1.26 MMC--MSI Message Control Register (Intel(R) High Definition Audio Controller--D27:F0) ..................... 631 17.1.1.27 MMLA--MSI Message Lower Address Register (Intel(R) High Definition Audio Controller--D27:F0) ..................... 632 17.1.1.28 MMUA--MSI Message Upper Address Register (Intel(R) High Definition Audio Controller--D27:F0) ..................... 632 17.1.1.29 MMD--MSI Message Data Register (Intel(R) High Definition Audio Controller--D27:F0) ..................... 632 17.1.1.30 PXID--PCI Express* Capability ID Register (Intel(R) High Definition Audio Controller--D27:F0) ..................... 632 17.1.1.31 PXC--PCI Express* Capabilities Register (Intel(R) High Definition Audio Controller--D27:F0) ..................... 632 17.1.1.32 DEVCAP--Device Capabilities Register (Intel(R) High Definition Audio Controller--D27:F0) ..................... 633 17.1.1.33 DEVC--Device Control Register (Intel(R) High Definition Audio Controller--D27:F0) ..................... 633 17.1.1.34 DEVS--Device Status Register (Intel(R) High Definition Audio Controller--D27:F0) ..................... 634 17.1.1.35 VCCAP--Virtual Channel Enhanced Capability Header (Intel(R) High Definition Audio Controller--D27:F0) ..................... 634 17.1.1.36 PVCCAP1--Port VC Capability Register 1 (Intel(R) High Definition Audio Controller--D27:F0) ..................... 635 17.1.1.37 PVCCAP2--Port VC Capability Register 2 (Intel(R) High Definition Audio Controller--D27:F0) ..................... 635 17.1.1.38 PVCCTL--Port VC Control Register (Intel(R) High Definition Audio Controller--D27:F0) ..................... 635 17.1.1.39 PVCSTS--Port VC Status Register (Intel(R) High Definition Audio Controller--D27:F0) ..................... 635 17.1.1.40 VC0CAP--VC0 Resource Capability Register (Intel(R) High Definition Audio Controller--D27:F0) ..................... 636 17.1.1.41 VC0CTL--VC0 Resource Control Register (Intel(R) High Definition Audio Controller--D27:F0) ..................... 636 17.1.1.42 VC0STS--VC0 Resource Status Register (Intel(R) High Definition Audio Controller--D27:F0) ..................... 636 17.1.1.43 VCiCAP--VCi Resource Capability Register (Intel(R) High Definition Audio Controller--D27:F0) ..................... 637 17.1.1.44 VCiCTL--VCi Resource Control Register (Intel(R) High Definition Audio Controller--D27:F0) ..................... 637 17.1.1.45 VCiSTS--VCi Resource Status Register (Intel(R) High Definition Audio Controller--D27:F0) ..................... 637 17.1.1.46 RCCAP--Root Complex Link Declaration Enhanced Capability Header Register (Intel(R) High Definition Audio Controller--D27:F0) ..................... 638 17.1.1.47 ESD--Element Self Description Register (Intel(R) High Definition Audio Controller--D27:F0) ..................... 638 Datasheet 21 17.1.1.48 L1DESC--Link 1 Description Register (Intel(R) High Definition Audio Controller--D27:F0) ...................... 638 17.1.1.49 L1ADDL--Link 1 Lower Address Register (Intel(R) High Definition Audio Controller--D27:F0) ...................... 638 17.1.1.50 L1ADDU--Link 1 Upper Address Register (Intel(R) High Definition Audio Controller--D27:F0) ...................... 639 17.1.2 Intel(R) High Definition Audio Memory Mapped Configuration Registers (Intel(R) High Definition Audio D27:F0) .................................................... 640 17.1.2.1 GCAP--Global Capabilities Register (Intel(R) High Definition Audio Controller--D27:F0) ...................... 643 17.1.2.2 VMIN--Minor Version Register (Intel(R) High Definition Audio Controller--D27:F0) ...................... 644 17.1.2.3 VMAJ--Major Version Register (Intel(R) High Definition Audio Controller--D27:F0) ...................... 644 17.1.2.4 OUTPAY--Output Payload Capability Register (Intel(R) High Definition Audio Controller--D27:F0) ...................... 644 17.1.2.5 INPAY--Input Payload Capability Register (Intel(R) High Definition Audio Controller--D27:F0) ...................... 644 17.1.2.6 GCTL--Global Control Register (Intel(R) High Definition Audio Controller--D27:F0) ...................... 645 17.1.2.7 WAKEEN--Wake Enable Register (Intel(R) High Definition Audio Controller--D27:F0) ...................... 646 17.1.2.8 STATESTS--State Change Status Register (Intel(R) High Definition Audio Controller--D27:F0) ...................... 646 17.1.2.9 GSTS--Global Status Register (Intel(R) High Definition Audio Controller--D27:F0) ...................... 646 17.1.2.10 GCAP2 Global Capabilities 2 Register (Intel(R) High Definition Audio Controller--D27:F0) ...................... 647 17.1.2.11 OUTSTRMPAY--Output Stream Payload Capability (Intel(R) High Definition Audio Controller--D27:F0) ...................... 647 17.1.2.12 INSTRMPAY--Input Stream Payload Capability (Intel(R) High Definition Audio Controller--D27:F0) ...................... 647 17.1.2.13 INTCTL--Interrupt Control Register (Intel(R) High Definition Audio Controller--D27:F0) ...................... 648 17.1.2.14 INTSTS--Interrupt Status Register (Intel(R) High Definition Audio Controller--D27:F0) ...................... 649 17.1.2.15 WALCLK--Wall Clock Counter Register (Intel(R) High Definition Audio Controller--D27:F0) ...................... 649 17.1.2.16 SSYNC--Stream Synchronization Register (Intel(R) High Definition Audio Controller--D27:F0) ...................... 650 17.1.2.17 CORBLBASE--CORB Lower Base Address Register (Intel(R) High Definition Audio Controller--D27:F0) ...................... 650 17.1.2.18 CORBUBASE--CORB Upper Base Address Register (Intel(R) High Definition Audio Controller--D27:F0) ...................... 650 17.1.2.19 CORBWP--CORB Write Pointer Register (Intel(R) High Definition Audio Controller--D27:F0) ...................... 651 17.1.2.20 CORBRP--CORB Read Pointer Register (Intel(R) High Definition Audio Controller--D27:F0) ...................... 651 17.1.2.21 CORBCTL--CORB Control Register (Intel(R) High Definition Audio Controller--D27:F0) ...................... 651 17.1.2.22 CORBST--CORB Status Register (Intel(R) High Definition Audio Controller--D27:F0) ...................... 652 17.1.2.23 CORBSIZE--CORB Size Register Intel(R) High Definition Audio Controller--D27:F0) ....................... 652 17.1.2.24 RIRBLBASE--RIRB Lower Base Address Register (Intel(R) High Definition Audio Controller--D27:F0) ...................... 652 17.1.2.25 RIRBUBASE--RIRB Upper Base Address Register (Intel(R) High Definition Audio Controller--D27:F0) ...................... 652 17.1.2.26 RIRBWP--RIRB Write Pointer Register (Intel(R) High Definition Audio Controller--D27:F0) ...................... 653 17.1.2.27 RINTCNT--Response Interrupt Count Register (Intel(R) High Definition Audio Controller--D27:F0) ...................... 653 17.1.2.28 RIRBCTL--RIRB Control Register (Intel(R) High Definition Audio Controller--D27:F0) ...................... 653 17.1.2.29 RIRBSTS--RIRB Status Register (Intel(R) High Definition Audio Controller--D27:F0) ...................... 654 22 Datasheet 17.1.2.30 RIRBSIZE--RIRB Size Register (Intel(R) High Definition Audio Controller--D27:F0) ..................... 654 17.1.2.31 IC--Immediate Command Register (Intel(R) High Definition Audio Controller--D27:F0) ..................... 654 17.1.2.32 IR--Immediate Response Register (Intel(R) High Definition Audio Controller--D27:F0) ..................... 655 17.1.2.33 ICS--Immediate Command Status Register (Intel(R) High Definition Audio Controller--D27:F0) ..................... 655 17.1.2.34 DPLBASE--DMA Position Lower Base Address Register (Intel(R) High Definition Audio Controller--D27:F0) ..................... 655 17.1.2.35 DPUBASE--DMA Position Upper Base Address Register (Intel(R) High Definition Audio Controller--D27:F0) ..................... 656 17.1.2.36 SDCTL--Stream Descriptor Control Register (Intel(R) High Definition Audio Controller--D27:F0) ..................... 656 17.1.2.37 SDSTS--Stream Descriptor Status Register (Intel(R) High Definition Audio Controller--D27:F0) ..................... 657 17.1.2.38 SDLPIB--Stream Descriptor Link Position in Buffer Register (Intel(R) High Definition Audio Controller--D27:F0) ......... 658 17.1.2.39 SDCBL--Stream Descriptor Cyclic Buffer Length Register (Intel(R) High Definition Audio Controller--D27:F0) ..................... 658 17.1.2.40 SDLVI--Stream Descriptor Last Valid Index Register (Intel(R) High Definition Audio Controller--D27:F0) ..................... 659 17.1.2.41 SDFIFOW--Stream Descriptor FIFO Watermark Register (Intel(R) High Definition Audio Controller--D27:F0) ..................... 659 17.1.2.42 ISDFIFOS--Input Stream Descriptor FIFO Size Register (Intel(R) High Definition Audio Controller--D27:F0) ..................... 660 17.1.2.43 SDFMT--Stream Descriptor Format Register (Intel(R) High Definition Audio Controller--D27:F0) ..................... 660 17.1.2.44 SdBDPL--Stream Descriptor Buffer Descriptor List Pointer Lower Base Address Register (Intel(R) High Definition Audio Controller--D27:F0) ..................... 661 17.1.2.45 SdBDPU--Stream Descriptor Buffer Descriptor List Pointer Upper Base Address Register (Intel(R) High Definition Audio Controller--D27:F0) ..................... 661 18 SMBus Controller Registers (D31:F3) .................................................................... 662 18.1 PCI Configuration Registers (SMBus--D31:F3)..................................................... 662 18.1.1 VID--Vendor Identification Register (SMBus--D31:F3) ............................. 662 18.1.2 DID--Device Identification Register (SMBus--D31:F3).............................. 663 18.1.3 PCICMD--PCI Command Register (SMBus--D31:F3)................................. 663 18.1.4 PCISTS--PCI Status Register (SMBus--D31:F3)....................................... 664 18.1.5 RID--Revision Identification Register (SMBus--D31:F3)............................ 664 18.1.6 PI--Programming Interface Register (SMBus--D31:F3)............................. 664 18.1.7 SCC--Sub Class Code Register (SMBus--D31:F3) .................................... 665 18.1.8 BCC--Base Class Code Register (SMBus--D31:F3) ................................... 665 18.1.9 SMBMBAR0--D31_F3_SMBus Memory Base Address 0 Register (SMBus--D31:F3) ................................................................... 665 18.1.10 SMBMBAR1--D31_F3_SMBus Memory Base Address 1 Register (SMBus--D31:F3) ................................................................... 665 18.1.11 SMB_BASE--SMBus Base Address Register (SMBus--D31:F3) ............................................................................... 666 18.1.12 SVID--Subsystem Vendor Identification Register (SMBus--D31:F2/F4) ........................................................................... 666 18.1.13 SID--Subsystem Identification Register (SMBus--D31:F2/F4) ........................................................................... 666 18.1.14 INT_LN--Interrupt Line Register (SMBus--D31:F3) .................................. 666 18.1.15 INT_PN--Interrupt Pin Register (SMBus--D31:F3) ................................... 667 18.1.16 HOSTC--Host Configuration Register (SMBus--D31:F3) ............................ 667 18.2 SMBus I/O and Memory Mapped I/O Registers .................................................... 668 18.2.1 HST_STS--Host Status Register (SMBus--D31:F3) .................................. 669 18.2.2 HST_CNT--Host Control Register (SMBus--D31:F3) ................................. 670 18.2.3 HST_CMD--Host Command Register (SMBus--D31:F3) ............................ 671 18.2.4 XMIT_SLVA--Transmit Slave Address Register (SMBus--D31:F3) ............................................................................... 671 18.2.5 HST_D0--Host Data 0 Register (SMBus--D31:F3).................................... 671 18.2.6 HST_D1--Host Data 1 Register (SMBus--D31:F3).................................... 672 Datasheet 23 18.2.7 18.2.8 18.2.9 18.2.10 18.2.11 18.2.12 18.2.13 18.2.14 18.2.15 18.2.16 18.2.17 18.2.18 18.2.19 19 24 Host_BLOCK_dB--Host Block Data Byte Register (SMBus--D31:F3) ................................................................................ 672 PEC--Packet Error Check (PEC) Register (SMBus--D31:F3) ................................................................................ 672 RCV_SLVA--Receive Slave Address Register (SMBus--D31:F3) ................................................................................ 673 SLV_DATA--Receive Slave Data Register (SMBus--D31:F3)....................... 673 AUX_STS--Auxiliary Status Register (SMBus--D31:F3) ............................. 673 AUX_CTL--Auxiliary Control Register (SMBus--D31:F3) ............................ 674 SMLINK_PIN_CTL--SMLink Pin Control Register (SMBus--D31:F3) ................................................................................ 674 SMBus_PIN_CTL--SMBus Pin Control Register (SMBus--D31:F3) ................................................................................ 675 SLV_STS--Slave Status Register (SMBus--D31:F3) .................................. 675 SLV_CMD--Slave Command Register (SMBus--D31:F3) ............................ 676 NOTIFY_DADDR--Notify Device Address Register (SMBus--D31:F3) ................................................................................ 676 NOTIFY_DLOW--Notify Data Low Byte Register (SMBus--D31:F3) ................................................................................ 676 NOTIFY_DHIGH--Notify Data High Byte Register (SMBus--D31:F3) ................................................................................ 677 PCI Express* Configuration Registers .................................................................... 678 19.1 PCI Express* Configuration Registers (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ................................................... 678 19.1.1 VID--Vendor Identification Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ....................................... 680 19.1.2 DID--Device Identification Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ....................................... 680 19.1.3 PCICMD--PCI Command Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ....................................... 681 19.1.4 PCISTS--PCI Status Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ....................................... 682 19.1.5 RID--Revision Identification Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ....................................... 683 19.1.6 PI--Programming Interface Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ....................................... 683 19.1.7 SCC--Sub Class Code Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ....................................... 683 19.1.8 BCC--Base Class Code Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ....................................... 683 19.1.9 CLS--Cache Line Size Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ....................................... 684 19.1.10 PLT--Primary Latency Timer Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ....................................... 684 19.1.11 HEADTYP--Header Type Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ....................................... 684 19.1.12 BNUM--Bus Number Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ....................................... 685 19.1.13 SLT--Secondary Latency Timer Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ....................................... 685 19.1.14 IOBL--I/O Base and Limit Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ....................................... 685 19.1.15 SSTS--Secondary Status Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ....................................... 686 19.1.16 MBL--Memory Base and Limit Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ....................................... 687 19.1.17 PMBL--Prefetchable Memory Base and Limit Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ....................................... 687 19.1.18 PMBU32--Prefetchable Memory Base Upper 32 Bits Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7)........................... 687 19.1.19 PMLU32--Prefetchable Memory Limit Upper 32 Bits Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7)........................... 688 19.1.20 CAPP--Capabilities List Pointer Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ....................................... 688 19.1.21 INTR--Interrupt Information Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ....................................... 688 Datasheet 19.1.22 BCTRL--Bridge Control Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ...................................... 689 19.1.23 CLIST--Capabilities List Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ...................................... 689 19.1.24 XCAP--PCI Express* Capabilities Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ...................................... 690 19.1.25 DCAP--Device Capabilities Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ...................................... 690 19.1.26 DCTL--Device Control Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ...................................... 691 19.1.27 DSTS--Device Status Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ...................................... 692 19.1.28 LCAP--Link Capabilities Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ...................................... 692 19.1.29 LCTL--Link Control Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ...................................... 694 19.1.30 LSTS--Link Status Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ...................................... 695 19.1.31 SLCAP--Slot Capabilities Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ...................................... 696 19.1.32 SLCTL--Slot Control Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ...................................... 697 19.1.33 SLSTS--Slot Status Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ...................................... 697 19.1.34 RCTL--Root Control Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ...................................... 698 19.1.35 RSTS--Root Status Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ...................................... 698 19.1.36 DCAP2--Device Capabilities 2 Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ...................................... 699 19.1.37 DCTL2--Device Control 2 Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ...................................... 699 19.1.38 LCTL2--Link Control 2 Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ...................................... 700 19.1.39 LSTS2--Link Status 2 Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ...................................... 701 19.1.40 MID--Message Signaled Interrupt Identifiers Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ...................................... 702 19.1.41 MC--Message Signaled Interrupt Message Control Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ...................................... 702 19.1.42 MA--Message Signaled Interrupt Message Address Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) .......................... 702 19.1.43 MD--Message Signaled Interrupt Message Data Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ...................................... 703 19.1.44 SVCAP--Subsystem Vendor Capability Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ...................................... 703 19.1.45 SVID--Subsystem Vendor Identification Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ...................................... 703 19.1.46 PMCAP--Power Management Capability Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ...................................... 703 19.1.47 PMC--PCI Power Management Capabilities Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ...................................... 704 19.1.48 PMCS--PCI Power Management Control and Status Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) .......................... 704 19.1.49 MPC2--Miscellaneous Port Configuration Register 2 (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ...................................... 705 19.1.50 MPC--Miscellaneous Port Configuration Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ...................................... 705 19.1.51 SMSCS--SMI/SCI Status Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ...................................... 707 19.1.52 RPDCGEN--Root Port Dynamic Clock Gating Enable Register (PCI Express--D28:F0/F1/F2/F3/F4/F5/F6/F7) ............................ 707 19.1.53 PECR3--PCI Express* Configuration Register 3 (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ...................................... 708 19.1.54 PECR4--PCI Express* Configuration Register 4 (PCI Express*--D28:F0/F1/F2/F3/F4/F5)................................................ 708 Datasheet 25 19.1.55 UES--Uncorrectable Error Status Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ....................................... 710 19.1.56 UEM--Uncorrectable Error Mask Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ....................................... 711 19.1.57 UEV--Uncorrectable Error Severity Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ....................................... 712 19.1.58 CES--Correctable Error Status Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ....................................... 713 19.1.59 CEM--Correctable Error Mask Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ....................................... 713 19.1.60 AECC--Advanced Error Capabilities and Control Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ....................................... 714 19.1.61 RES--Root Error Status Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ....................................... 714 19.1.62 PECR2--PCI Express* Configuration Register 2 (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ....................................... 715 19.1.63 PEETM--PCI Express* Extended Test Mode Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ....................................... 715 19.1.64 PEC1--PCI Express* Configuration Register 1 (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ....................................... 715 20 High Precision Event Timer Registers..................................................................... 716 20.1 Memory Mapped Registers ................................................................................ 716 20.1.1 GCAP_ID--General Capabilities and Identification Register ........................ 717 20.1.2 GEN_CONF--General Configuration Register ............................................ 718 20.1.3 GINTR_STA--General Interrupt Status Register ....................................... 718 20.1.4 MAIN_CNT--Main Counter Value Register................................................ 719 20.1.5 TIMn_CONF--Timer n Configuration and Capabilities Register .................... 719 20.1.6 TIMn_COMP--Timer n Comparator Value Register .................................... 721 20.1.7 TIMERn_PROCMSG_ROUT--Timer n Processor Message Interrupt Rout Register ........................................................................ 722 21 Serial Peripheral Interface (SPI) ........................................................................... 723 21.1 Serial Peripheral Interface Memory Mapped Configuration Registers........................ 723 21.1.1 BFPR -BIOS Flash Primary Region Register (SPI Memory Mapped Configuration Registers) ........................................ 724 21.1.2 HSFS--Hardware Sequencing Flash Status Register (SPI Memory Mapped Configuration Registers) ........................................ 725 21.1.3 HSFC--Hardware Sequencing Flash Control Register (SPI Memory Mapped Configuration Registers) ........................................ 726 21.1.4 FADDR--Flash Address Register (SPI Memory Mapped Configuration Registers) ........................................ 726 21.1.5 FDATA0--Flash Data 0 Register (SPI Memory Mapped Configuration Registers) ........................................ 727 21.1.6 FDATAN--Flash Data [N] Register (SPI Memory Mapped Configuration Registers) ........................................ 727 21.1.7 FRAP--Flash Regions Access Permissions Register (SPI Memory Mapped Configuration Registers) ........................................ 728 21.1.8 FREG0--Flash Region 0 (Flash Descriptor) Register (SPI Memory Mapped Configuration Registers) ........................................ 728 21.1.9 FREG1--Flash Region 1 (BIOS Descriptor) Register (SPI Memory Mapped Configuration Registers) ........................................ 729 21.1.10 FREG2--Flash Region 2 (Intel(R) ME) Register (SPI Memory Mapped Configuration Registers) ........................................ 729 21.1.11 FREG3--Flash Region 3 (GbE) Register (SPI Memory Mapped Configuration Registers) ........................................ 729 21.1.12 FREG4--Flash Region 4 (Platform Data) Register (SPI Memory Mapped Configuration Registers) ........................................ 730 21.1.13 PR0--Protected Range 0 Register (SPI Memory Mapped Configuration Registers) ........................................ 730 21.1.14 PR1--Protected Range 1 Register (SPI Memory Mapped Configuration Registers) ........................................ 731 21.1.15 PR2--Protected Range 2 Register (SPI Memory Mapped Configuration Registers) ........................................ 731 21.1.16 PR3--Protected Range 3 Register (SPI Memory Mapped Configuration Registers) ........................................ 732 26 Datasheet 21.2 21.3 21.4 Datasheet 21.1.17 PR4--Protected Range 4 Register (SPI Memory Mapped Configuration Registers) ........................................ 732 21.1.18 SSFS--Software Sequencing Flash Status Register (SPI Memory Mapped Configuration Registers) ........................................ 733 21.1.19 SSFC--Software Sequencing Flash Control Register (SPI Memory Mapped Configuration Registers) ........................................ 734 21.1.20 PREOP--Prefix Opcode Configuration Register (SPI Memory Mapped Configuration Registers) ........................................ 735 21.1.21 OPTYPE--Opcode Type Configuration Register (SPI Memory Mapped Configuration Registers) ........................................ 735 21.1.22 OPMENU--Opcode Menu Configuration Register (SPI Memory Mapped Configuration Registers) ........................................ 736 21.1.23 BBAR--BIOS Base Address Configuration Register (SPI Memory Mapped Configuration Registers) ........................................ 736 21.1.24 FDOC--Flash Descriptor Observability Control Register (SPI Memory Mapped Configuration Registers) ........................................ 737 21.1.25 FDOD--Flash Descriptor Observability Data Register (SPI Memory Mapped Configuration Registers) ........................................ 737 21.1.26 AFC--Additional Flash Control Register (SPI Memory Mapped Configuration Registers) ........................................ 737 21.1.27 LVSCC--Host Lower Vendor Specific Component Capabilities Register (SPI Memory Mapped Configuration Registers) ........................................ 738 21.1.28 UVSCC--Host Upper Vendor Specific Component Capabilities Register (SPI Memory Mapped Configuration Registers) ........................................ 739 21.1.29 PTINX--Flash Parameter Table Index Register ......................................... 740 21.1.30 PTDATA--Flash Parameter Table Data Register........................................ 740 21.1.31 SRDL--Soft Reset Data Lock Register (SPI Memory Mapped Configuration Registers) ........................................ 740 21.1.32 SRDC--Soft Reset Data Control Register (SPI Memory Mapped Configuration Registers) ........................................ 741 21.1.33 SRD--Soft Reset Data Register (SPI Memory Mapped Configuration Registers) ........................................ 741 Flash Descriptor Records .................................................................................. 741 OEM Section ................................................................................................... 741 GbE SPI Flash Program Registers....................................................................... 742 21.4.1 GLFPR -Gigabit LAN Flash Primary Region Register (GbE LAN Memory Mapped Configuration Registers)................................. 743 21.4.2 HSFS--Hardware Sequencing Flash Status Register (GbE LAN Memory Mapped Configuration Registers)................................. 743 21.4.3 HSFC--Hardware Sequencing Flash Control Register (GbE LAN Memory Mapped Configuration Registers)................................. 744 21.4.4 FADDR--Flash Address Register (GbE LAN Memory Mapped Configuration Registers)................................. 745 21.4.5 FDATA0--Flash Data 0 Register (GbE LAN Memory Mapped Configuration Registers)................................. 745 21.4.6 FRAP--Flash Regions Access Permissions Register (GbE LAN Memory Mapped Configuration Registers)................................. 745 21.4.7 FREG0--Flash Region 0 (Flash Descriptor) Register (GbE LAN Memory Mapped Configuration Registers)................................. 746 21.4.8 FREG1--Flash Region 1 (BIOS Descriptor) Register (GbE LAN Memory Mapped Configuration Registers)................................. 746 21.4.9 FREG2--Flash Region 2 (Intel(R) ME) Register (GbE LAN Memory Mapped Configuration Registers)................................. 746 21.4.10 FREG3--Flash Region 3 (GbE) Register (GbE LAN Memory Mapped Configuration Registers)................................. 747 21.4.11 PR0--Protected Range 0 Register (GbE LAN Memory Mapped Configuration Registers)................................. 747 21.4.12 PR1--Protected Range 1 Register (GbE LAN Memory Mapped Configuration Registers)................................. 748 21.4.13 SSFS--Software Sequencing Flash Status Register (GbE LAN Memory Mapped Configuration Registers)................................. 748 21.4.14 SSFC--Software Sequencing Flash Control Register (GbE LAN Memory Mapped Configuration Registers)................................. 749 21.4.15 PREOP--Prefix Opcode Configuration Register (GbE LAN Memory Mapped Configuration Registers)................................. 750 21.4.16 OPTYPE--Opcode Type Configuration Register (GbE LAN Memory Mapped Configuration Registers)................................. 750 27 21.4.17 OPMENU--Opcode Menu Configuration Register (GbE LAN Memory Mapped Configuration Registers) ................................. 751 22 Thermal Sensor Registers (D31:F6) ....................................................................... 752 22.1 PCI Bus Configuration Registers......................................................................... 752 22.1.1 VID--Vendor Identification Register ....................................................... 752 22.1.2 DID--Device Identification Register ........................................................ 753 22.1.3 CMD--Command Register ..................................................................... 753 22.1.4 STS--Status Register ........................................................................... 753 22.1.5 RID--Revision Identification Register...................................................... 754 22.1.6 PI--Programming Interface Register....................................................... 754 22.1.7 SCC--Sub Class Code Register .............................................................. 754 22.1.8 BCC--Base Class Code Register ............................................................. 754 22.1.9 CLS--Cache Line Size Register .............................................................. 754 22.1.10 LT--Latency Timer Register................................................................... 755 22.1.11 HTYPE--Header Type Register ............................................................... 755 22.1.12 TBAR--Thermal Base Register ............................................................... 755 22.1.13 TBARH--Thermal Base High DWord Register............................................ 755 22.1.14 SVID--Subsystem Vendor ID Register .................................................... 756 22.1.15 SID--Subsystem ID Register ................................................................. 756 22.1.16 CAP_PTR--Capabilities Pointer Register................................................... 756 22.1.17 INTLN--Interrupt Line Register .............................................................. 756 22.1.18 INTPN--Interrupt Pin Register ............................................................... 757 22.1.19 TBARB--BIOS Assigned Thermal Base Address Register ............................ 757 22.1.20 TBARBH--BIOS Assigned Thermal Base High DWord Register ................................................................................... 757 22.1.21 PID--PCI Power Management Capability ID Register ................................. 757 22.1.22 PC--Power Management Capabilities Register .......................................... 758 22.1.23 PCS--Power Management Control And Status Register.............................. 758 22.2 Thermal Memory Mapped Configuration Registers (Thermal Sensor - D31:F26) ............................................................................. 759 22.2.1 TEMP--Temperature Register ................................................................ 759 22.2.2 TSC--Thermal Sensor Control Register ................................................... 760 22.2.3 TSS--Thermal Sensor Status Register .................................................... 760 22.2.4 TSEL--Thermal Sensor Enable and Lock Register ..................................... 760 22.2.5 TSREL--Thermal Sensor Reporting Enable and Lock Register ..................... 761 22.2.6 TSMIC--Thermal Sensor SMI Control Register ......................................... 761 22.2.7 CTT--Catastrophic Trip Point Register..................................................... 761 22.2.8 TAHV--Thermal Alert High Value Register ............................................... 761 22.2.9 TALV--Thermal Alert Low Value Register................................................. 762 22.2.10 TL--Throttle Levels Register .................................................................. 762 22.2.11 PHL--PCH Hot Level Register................................................................. 763 22.2.12 PHLC--PHL Control Register .................................................................. 763 22.2.13 TAS--Thermal Alert Status Register ....................................................... 763 22.2.14 TSPIEN--PCI Interrupt Event Enables Register......................................... 763 22.2.15 TSGPEN--General Purpose Event Enables Register ................................... 764 23 Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) ........... 765 23.1 First Intel(R) Management Engine Interface (Intel(R) MEI) Configuration Registers (Intel(R) MEI 1--D22:F0) .................................................................................... 765 23.1.1 PCI Configuration Registers (Intel(R) MEI 1--D22:F0)................................. 765 23.1.1.1 VID--Vendor Identification Register (Intel(R) MEI 1--D22:F0).......................................................... 766 23.1.1.2 DID--Device Identification Register (Intel(R) MEI 1--D22:F0).......................................................... 766 23.1.1.3 PCICMD--PCI Command Register (Intel(R) MEI 1--D22:F0).......................................................... 766 23.1.1.4 PCISTS--PCI Status Register (Intel(R) MEI 1--D22:F0).......................................................... 767 23.1.1.5 RID--Revision Identification Register (Intel(R) MEI 1--D22:F0).......................................................... 767 23.1.1.6 CC--Class Code Register (Intel(R) MEI 1--D22:F0).......................................................... 767 23.1.1.7 HTYPE--Header Type Register (Intel(R) MEI 1--D22:F0).......................................................... 768 23.1.1.8 MEI0_MBAR--Intel(R) MEI 1 MMIO Base Address (Intel(R) MEI 1--D22:F0).......................................................... 768 28 Datasheet 23.1.1.9 23.2 Datasheet SVID--Subsystem Vendor ID Register (Intel(R) MEI 1--D22:F0) ......................................................... 768 23.1.1.10 SID--Subsystem ID Register (Intel(R) MEI 1--D22:F0) ......................................................... 768 23.1.1.11 CAPP--Capabilities List Pointer Register (Intel(R) MEI 1--D22:F0) ......................................................... 769 23.1.1.12 INTR--Interrupt Information Register (Intel(R) MEI 1--D22:F0) ......................................................... 769 23.1.1.13 HFS--Host Firmware Status Register (Intel(R) MEI 1--D22:F0) ......................................................... 769 23.1.1.14 ME_UMA--Intel(R) Management Engine UMA Register (Intel(R) MEI 1--D22:F0) ......................................................... 769 23.1.1.15 GMES--General Intel(R) ME Status Register (Intel(R) MEI 1--D22:F0) ......................................................... 770 23.1.1.16 H_GS--Host General Status Register (Intel(R) MEI 1--D22:F0) ......................................................... 770 23.1.1.17 PID--PCI Power Management Capability ID Register (Intel(R) MEI 1--D22:F0) ......................................................... 770 23.1.1.18 PC--PCI Power Management Capabilities Register (Intel(R) MEI 1--D22:F0) ......................................................... 770 23.1.1.19 PMCS--PCI Power Management Control and Status Register (Intel(R) MEI 1--D22:F0) ............................................. 771 23.1.1.20 GMES2--General Intel(R) ME Status Register 2 (Intel(R) MEI 1--D22:F0) ......................................................... 771 23.1.1.21 GMES3--General Intel(R) ME Status Register 3 (Intel(R) MEI 1--D22:F0) ......................................................... 771 23.1.1.22 GMES4--General Intel(R) ME Status Register 4 (Intel(R) MEI 1--D22:F0) ......................................................... 772 23.1.1.23 GMES5--General Intel(R) ME Status Register 5 (Intel(R) MEI 1--D22:F0) ......................................................... 772 23.1.1.24 H_GS2--Host General Status Register 2 (Intel(R) MEI 1--D22:F0) ......................................................... 772 23.1.1.25 H_GS3--Host General Status Register 3 (Intel(R) MEI 1--D22:F0) ......................................................... 772 23.1.1.26 MID--Message Signaled Interrupt Identifiers Register (Intel(R) MEI 1--D22:F0) ......................................................... 772 23.1.1.27 MC--Message Signaled Interrupt Message Control Register (Intel(R) MEI 1--D22:F0) ......................................................... 773 23.1.1.28 MA--Message Signaled Interrupt Message Address Register (Intel(R) MEI 1--D22:F0) ......................................................... 773 23.1.1.29 MUA--Message Signaled Interrupt Upper Address Register (Intel(R) MEI 1--D22:F0) ......................................................... 773 23.1.1.30 MD--Message Signaled Interrupt Message Data Register (Intel(R) MEI 1--D22:F0) ......................................................... 773 23.1.1.31 HIDM--MEI Interrupt Delivery Mode Register (Intel(R) MEI 1--D22:F0) ......................................................... 774 23.1.1.32 HERES--Intel(R) MEI Extend Register Status (Intel(R) MEI 1--D22:F0) ......................................................... 774 23.1.1.33 HERX--Intel(R) MEI Extend Register DWX (Intel(R) MEI 1--D22:F0) ......................................................... 774 23.1.2 MEI0_MBAR--Intel(R) MEI 1 MMIO Registers............................................. 775 23.1.2.1 H_CB_WW--Host Circular Buffer Write Window Register (Intel(R) MEI 1 MMIO Register) ................................................. 775 23.1.2.2 H_CSR--Host Control Status Register (Intel(R) MEI 1 MMIO Register) ................................................. 775 23.1.2.3 ME_CB_RW--Intel(R) ME Circular Buffer Read Window Register (Intel(R) MEI 1 MMIO Register) ................................................. 776 23.1.2.4 ME_CSR_HA--Intel(R) ME Control Status Host Access Register (Intel(R) MEI 1 MMIO Register) ................................................. 776 Second Intel(R) Management Engine Interface (Intel(R) MEI 2) Configuration Registers (Intel(R) MEI 2--D22:F1) ................................................................................... 777 23.2.1 PCI Configuration Registers (Intel(R) MEI 2--D22:F2) ................................ 777 23.2.1.1 VID--Vendor Identification Register (Intel(R) MEI 2--D22:F1) ......................................................... 778 23.2.1.2 DID--Device Identification Register (Intel(R) MEI 2--D22:F1) ......................................................... 778 29 23.2.1.3 PCICMD--PCI Command Register (Intel(R) MEI 2--D22:F1).......................................................... 778 23.2.1.4 PCISTS--PCI Status Register (Intel(R) MEI 2--D22:F1).......................................................... 779 23.2.1.5 RID--Revision Identification Register (Intel(R) MEI 2--D22:F1).......................................................... 779 23.2.1.6 CC--Class Code Register (Intel(R) MEI 2--D22:F1).......................................................... 779 23.2.1.7 HTYPE--Header Type Register (Intel(R) MEI 2--D22:F1).......................................................... 779 23.2.1.8 MEI1_MBAR--Intel MEI 2 MMIO Base Address (Intel(R) MEI 2--D22:F1).......................................................... 780 23.2.1.9 SVID--Subsystem Vendor ID Register (Intel(R) MEI 2--D22:F1).......................................................... 780 23.2.1.10 SID--Subsystem ID Register (Intel(R) MEI 2--D22:F1).......................................................... 780 23.2.1.11 CAPP--Capabilities List Pointer Register (Intel(R) MEI 2--D22:F1).......................................................... 780 23.2.1.12 INTR--Interrupt Information Register (Intel(R) MEI 2--D22:F1).......................................................... 781 23.2.1.13 HFS--Host Firmware Status Register (Intel(R) MEI 2--D22:F1).......................................................... 781 23.2.1.14 GMES--General Intel(R) ME Status Register (Intel(R) MEI 2--D22:F1).......................................................... 781 23.2.1.15 H_GS--Host General Status Register (Intel(R) MEI 2--D22:F1).......................................................... 781 23.2.1.16 PID--PCI Power Management Capability ID Register (Intel(R) MEI 2--D22:F1).......................................................... 781 23.2.1.17 PC--PCI Power Management Capabilities Register (Intel(R) MEI 2--D22:F1).......................................................... 782 23.2.1.18 PMCS--PCI Power Management Control and Status Register (Intel(R) MEI 2--D22:F1) ............................................. 782 23.2.1.19 GMES2--General Intel(R) ME Status Register 2 (Intel(R) MEI 2--D22:F1).......................................................... 783 23.2.1.20 GMES3--General Intel(R) ME Status Register 3 (Intel(R) MEI 2--D22:F1).......................................................... 783 23.2.1.21 GMES4--General Intel(R) ME Status Register 4 (Intel(R) MEI 2--D22:F1).......................................................... 783 23.2.1.22 GMES5--General Intel(R) ME Status Register 5 (Intel(R) MEI 2--D22:F1).......................................................... 783 23.2.1.23 H_GS2--Host General Status Register 2 (Intel(R) MEI 2--D22:F1).......................................................... 783 23.2.1.24 H_GS3--Host General Status Register 3 (Intel(R) MEI 2--D22:F1).......................................................... 784 23.2.1.25 MID--Message Signaled Interrupt Identifiers Register (Intel(R) MEI 2--D22:F1).......................................................... 784 23.2.1.26 MC--Message Signaled Interrupt Message Control Register (Intel(R) MEI 2--D22:F1).......................................................... 784 23.2.1.27 MA--Message Signaled Interrupt Message Address Register (Intel(R) MEI 2--D22:F1).......................................................... 784 23.2.1.28 MUA--Message Signaled Interrupt Upper Address Register (Intel(R) MEI 2--D22:F1).......................................................... 785 23.2.1.29 MD--Message Signaled Interrupt Message Data Register (Intel(R) MEI 2--D22:F1).......................................................... 785 23.2.1.30 HIDM--Intel(R) MEI Interrupt Delivery Mode Register (Intel(R) MEI 2--D22:F1).......................................................... 785 23.2.1.31 HERES--Intel(R) MEI Extend Register Status (Intel(R) MEI 2--D22:F1).......................................................... 785 23.2.1.32 HERX--Intel(R) MEI Extend Register DWX (Intel(R) MEI 2--D22:F1).......................................................... 786 23.2.2 MEI1_MBAR--Intel(R) MEI 2 MMIO Registers ............................................. 786 23.2.2.1 H_CB_WW--Host Circular Buffer Write Window (Intel(R) MEI 2 MMIO Register) ................................................. 786 23.2.2.2 H_CSR--Host Control Status Register (Intel(R) MEI 2 MMIO Register) ................................................. 787 23.2.2.3 ME_CB_RW--Intel(R) ME Circular Buffer Read Window Register (Intel(R) MEI 2 MMIO Register) ................................................. 787 30 Datasheet ME_CSR_HA--Intel(R) ME Control Status Host Access Register (Intel(R) MEI 2 MMIO Register) ................................................. 788 IDE Redirect IDER Registers (IDER--D22:F2) ...................................................... 789 23.3.1 PCI Configuration Registers (IDER--D22:F2) ........................................... 789 23.3.1.1 VID--Vendor Identification Register (IDER--D22:F2).................. 789 23.3.1.2 DID--Device Identification Register (IDER--D22:F2) .................. 790 23.3.1.3 PCICMD--PCI Command Register (IDER--D22:F2) ..................... 790 23.3.1.4 PCISTS--PCI Device Status Register (IDER--D22:F2)................. 790 23.3.1.5 RID--Revision Identification Register (IDER--D22:F2) ................ 790 23.3.1.6 CC--Class Codes Register (IDER--D22:F2) ............................... 791 23.3.1.7 CLS--Cache Line Size Register (IDER--D22:F2)......................... 791 23.3.1.8 PCMdBA--Primary Command Block IO Bar Register (IDER--D22:F2) ....................................................... 791 23.3.1.9 PCTLBA--Primary Control Block Base Address Register (IDER--D22:F2) ....................................................... 791 23.3.1.10 SCMdBA--Secondary Command Block Base Address Register (IDER--D22:F2) ....................................................... 792 23.3.1.11 SCTLBA--Secondary Control Block base Address Register (IDER--D22:F2) ....................................................... 792 23.3.1.12 LBAR--Legacy Bus Master Base Address Register (IDER--D22:F2).................................................................... 792 23.3.1.13 SVID--Subsystem Vendor ID Register (IDER--D22:F2) .............. 792 23.3.1.14 SID--Subsystem ID Register (IDER--D22:F2) ........................... 793 23.3.1.15 CAPP--Capabilities List Pointer Register (IDER--D22:F2).................................................................... 793 23.3.1.16 INTR--Interrupt Information Register (IDER--D22:F2).................................................................... 793 23.3.1.17 PID--PCI Power Management Capability ID Register (IDER--D22:F2).................................................................... 793 23.3.1.18 PC--PCI Power Management Capabilities Register (IDER--D22:F2).................................................................... 794 23.3.1.19 PMCS--PCI Power Management Control and Status Register (IDER--D22:F2) ....................................................... 794 23.3.1.20 MID--Message Signaled Interrupt Capability ID Register (IDER--D22:F2) ....................................................... 795 23.3.1.21 MC--Message Signaled Interrupt Message Control Register (IDER--D22:F2) ....................................................... 795 23.3.1.22 MA--Message Signaled Interrupt Message Address Register (IDER--D22:F2) ....................................................... 795 23.3.1.23 MAU--Message Signaled Interrupt Message Upper Address Register (IDER--D22:F2) ........................................... 795 23.3.1.24 MD--Message Signaled Interrupt Message Data Register (IDER--D22:F2) ....................................................... 796 23.3.2 IDER BAR0 Registers ........................................................................... 796 23.3.2.1 IDEDATA--IDE Data Register (IDER--D22:F2)........................... 797 23.3.2.2 IDEERD1--IDE Error Register DEV1 (IDER--D22:F2).................................................................... 797 23.3.2.3 IDEERD0--IDE Error Register DEV0 (IDER--D22:F2).................................................................... 797 23.3.2.4 IDEFR--IDE Features Register (IDER--D22:F2).................................................................... 798 23.3.2.5 IDESCIR--IDE Sector Count In Register (IDER--D22:F2).................................................................... 798 23.3.2.6 IDESCOR1--IDE Sector Count Out Register Device 1 Register (IDER--D22:F2) ....................................................... 798 23.3.2.7 IDESCOR0--IDE Sector Count Out Register Device 0 Register (IDER--D22:F2)..................................................... 799 23.3.2.8 IDESNOR0--IDE Sector Number Out Register Device 0 Register (IDER--D22:F2) .......................................... 799 23.3.2.9 IDESNOR1--IDE Sector Number Out Register Device 1 Register (IDER--D22:F2) .......................................... 799 23.3.2.10 IDESNIR--IDE Sector Number In Register (IDER--D22:F2) ......... 800 23.3.2.11 IDECLIR--IDE Cylinder Low In Register (IDER--D22:F2)............. 800 23.3.2.12 IDCLOR1--IDE Cylinder Low Out Register Device 1 Register (IDER--D22:F2) ....................................................... 800 23.3.2.13 IDCLOR0--IDE Cylinder Low Out Register Device 0 Register (IDER--D22:F2) ....................................................... 801 23.2.2.4 23.3 Datasheet 31 23.4 32 23.3.2.14 IDCHOR0--IDE Cylinder High Out Register Device 0 Register (IDER--D22:F2) ........................................................ 801 23.3.2.15 IDCHOR1--IDE Cylinder High Out Register Device 1 Register (IDER--D22:F2) ........................................................ 801 23.3.2.16 IDECHIR--IDE Cylinder High In Register (IDER--D22:F2) .................................................................... 802 23.3.2.17 IDEDHIR--IDE Drive/Head In Register (IDER--D22:F2) .................................................................... 802 23.3.2.18 IDDHOR1--IDE Drive Head Out Register Device 1 Register (IDER--D22:F2) ........................................................ 803 23.3.2.19 IDDHOR0--IDE Drive Head Out Register Device 0 Register (IDER--D22:F2) ........................................................ 803 23.3.2.20 IDESD0R--IDE Status Device 0 Register (IDER--D22:F2) .................................................................... 803 23.3.2.21 IDESD1R--IDE Status Device 1 Register (IDER--D22:F2) .................................................................... 804 23.3.2.22 IDECR--IDE Command Register (IDER--D22:F2) ....................... 805 23.3.3 IDER BAR1 Registers ........................................................................... 805 23.3.3.1 IDDCR--IDE Device Control Register (IDER--D22:F2)................. 805 23.3.3.2 IDASR--IDE Alternate Status Register (IDER--D22:F2)............... 806 23.3.4 IDER BAR4 Registers ........................................................................... 806 23.3.4.1 IDEPBMCR--IDE Primary Bus Master Command Register (IDER--D22:F2) ........................................................ 807 23.3.4.2 IDEPBMDS0R--IDE Primary Bus Master Device Specific 0 Register (IDER--D22:F2).......................................... 807 23.3.4.3 IDEPBMSR--IDE Primary Bus Master Status Register (IDER--D22:F2) ........................................................ 807 23.3.4.4 IDEPBMDS1R--IDE Primary Bus Master Device Specific 1 Register (IDER--D22:F2).......................................... 808 23.3.4.5 IDEPBMDTPR0--IDE Primary Bus Master Descriptor Table Pointer Byte 0 Register (IDER--D22:F2) ........................... 808 23.3.4.6 IDEPBMDTPR1--IDE Primary Bus Master Descriptor Table Pointer Byte 1 Register (IDER--D22:F2) ........................... 808 23.3.4.7 IDEPBMDTPR2--IDE Primary Bus Master Descriptor Table Pointer Byte 2 Register (IDER--D22:F2) ........................... 808 23.3.4.8 IDEPBMDTPR3--IDE Primary Bus Master Descriptor Table Pointer Byte 3 Register (IDER--D22:F2) ........................... 808 23.3.4.9 IDESBMCR--IDE Secondary Bus Master Command Register (IDER--D22:F2) ........................................................ 809 23.3.4.10 IDESBMDS0R--IDE Secondary Bus Master Device Specific 0 Register (IDER--D22:F2).......................................... 809 23.3.4.11 IDESBMSR--IDE Secondary Bus Master Status Register (IDER--D22:F2) ........................................................ 809 23.3.4.12 IDESBMDS1R--IDE Secondary Bus Master Device Specific 1 Register (IDER--D22:F2).......................................... 810 23.3.4.13 IDESBMDTPR0--IDE Secondary Bus Master Descriptor Table Pointer Byte 0 Register (IDER--D22:F2) ........................... 810 23.3.4.14 IDESBMDTPR1--IDE Secondary Bus Master Descriptor Table Pointer Byte 1 Register (IDER--D22:F2) ........................... 810 23.3.4.15 IDESBMDTPR2--IDE Secondary Bus Master Descriptor Table Pointer Byte 2 Register (IDER--D22:F2) ........................... 810 23.3.4.16 IDESBMDTPR3--IDE Secondary Bus Master Descriptor Table Pointer Byte 3 Register (IDER--D22:F2) ........................... 811 Serial Port for Remote Keyboard and Text (KT) Redirection (KT--D22:F3) ................................................................................. 811 23.4.1 PCI Configuration Registers (KT--D22:F3)............................................... 811 23.4.1.1 VID--Vendor Identification Register (KT--D22:F3) ..................... 812 23.4.1.2 DID--Device Identification Register (KT--D22:F3)...................... 812 23.4.1.3 CMD--Command Register (KT--D22:F3) ................................... 812 23.4.1.4 STS--Device Status Register (KT--D22:F3) ............................... 812 23.4.1.5 RID--Revision ID Register (KT--D22:F3) .................................. 813 23.4.1.6 CC--Class Codes Register (KT--D22:F3) ................................... 813 23.4.1.7 CLS--Cache Line Size Register (KT--D22:F3) ............................ 813 23.4.1.8 KTIBA--KT IO Block Base Address Register (KT--D22:F3) ....................................................................... 813 23.4.1.9 KTMBA--KT Memory Block Base Address Register (KT--D22:F3) ....................................................................... 814 Datasheet 23.4.1.10 23.4.1.11 23.4.1.12 23.4.1.13 23.4.1.14 SVID--Subsystem Vendor ID Register (KT--D22:F3).................. 814 SID--Subsystem ID Register (KT--D22:F3) .............................. 814 CAP--Capabilities Pointer Register (KT--D22:F3) ....................... 814 INTR--Interrupt Information Register (KT--D22:F3) .................. 815 PID--PCI Power Management Capability ID Register (KT--D22:F3) ....................................................................... 815 23.4.1.15 PC--PCI Power Management Capabilities ID Register (KT--D22:F3) ....................................................................... 815 23.4.1.16 MID--Message Signaled Interrupt Capability ID Register (KT--D22:F3)........................................................... 816 23.4.1.17 MC--Message Signaled Interrupt Message Control Register (KT--D22:F3)........................................................... 816 23.4.1.18 MA--Message Signaled Interrupt Message Address Register (KT--D22:F3)........................................................... 816 23.4.1.19 MAU--Message Signaled Interrupt Message Upper Address Register (KT--D22:F3)............................................... 817 23.4.1.20 MD--Message Signaled Interrupt Message Data Register (KT--D22:F3)........................................................... 817 23.4.2 KT IO/Memory Mapped Device Registers ................................................ 817 23.4.2.1 KTRxBR--KT Receive Buffer Register (KT--D22:F3).................... 818 23.4.2.2 KTTHR--KT Transmit Holding Register (KT--D22:F3).................. 818 23.4.2.3 KTDLLR--KT Divisor Latch LSB Register (KT--D22:F3)................ 818 23.4.2.4 KTIER--KT Interrupt Enable Register (KT--D22:F3) ................... 819 23.4.2.5 KTDLMR--KT Divisor Latch MSB Register (KT--D22:F3) .............. 819 23.4.2.6 KTIIR--KT Interrupt Identification Register (KT--D22:F3) ....................................................................... 819 23.4.2.7 KTFCR--KT FIFO Control Register (KT--D22:F3) ........................ 820 23.4.2.8 KTLCR--KT Line Control Register (KT--D22:F3) ......................... 820 23.4.2.9 KTMCR--KT Modem Control Register (KT--D22:F3).................... 821 23.4.2.10 KTLSR--KT Line Status Register (KT--D22:F3) .......................... 821 23.4.2.11 KTMSR--KT Modem Status Register (KT--D22:F3) ..................... 822 Figures 2-1 2-2 4-1 5-1 5-2 5-3 5-4 5-5 5-6 5-7 5-8 5-9 5-10 5-11 5-12 5-13 5-14 5-15 5-16 5-17 5-18 6-1 6-2 6-3 6-4 6-5 6-6 6-7 6-8 7-1 7-2 Datasheet PCH Interface Signals Block Diagram (not all signals are on all SKUs) ......................... 61 Example External RTC Circuit ................................................................................ 71 PCH Detailed Clock Diagram................................................................................ 110 Flexible I/O - High Speed Signal Mapping with PCI Express*, USB 3.0*, and SATA Ports ................................................................................................................ 112 Generation of SERR# to Platform ......................................................................... 117 Valid PCI Express* Ports for Platform LAN Connect Device (GbE) Support.................. 118 LPC Interface Diagram........................................................................................ 126 PCH DMA Controller ........................................................................................... 130 DMA Request Assertion through LDRQ# ................................................................ 134 Conceptual Diagram of SLP_LAN#........................................................................ 174 TCO Legacy/Compatible Mode SMBus Configuration................................................ 180 Advanced TCO Mode .......................................................................................... 182 Serial Post over GPIO Reference Circuit ................................................................ 184 Flow for Port Enable / Device Present Bits ............................................................. 192 Serial Data transmitted over the SGPIO Interface................................................... 196 EHCI with USB 2.0 with Rate Matching Hub ........................................................... 211 PCH Intel(R) Management Engine (Intel(R) ME) High-Level Block Diagram..................... 237 Flash Descriptor Sections .................................................................................... 240 PCH Display Architecture .................................................................................... 249 Analog Port Characteristics.................................................................................. 250 Panel Power Sequencing ..................................................................................... 252 Desktop/Server PCH Ballout (Top View - Upper Left) .............................................. 256 Desktop/Server PCH Ballout (Top View - Lower Left) .............................................. 256 Desktop/Server PCH Ballout (Top View - Upper Right) ............................................ 257 Desktop/Server PCH Ballout (Top View - Lower Right) ............................................ 257 Mobile PCH Ballout (Top View - Upper Left) ........................................................... 264 Mobile PCH Ballout (Top View - Lower Left) ........................................................... 264 Mobile PCH Ballout (Top View - Upper Right) ......................................................... 265 Mobile PCH Ballout (Top View - Lower Right) ......................................................... 265 Tape and Reel Pin 1 Location ............................................................................... 272 Desktop / Server PCH Package Drawing ................................................................ 273 33 7-3 7-4 8-1 8-2 8-3 8-4 8-5 8-6 8-7 8-8 8-10 8-11 8-9 8-12 8-13 8-14 8-15 8-16 8-17 8-18 8-19 8-20 8-21 8-22 8-23 8-24 8-25 8-26 8-27 8-28 8-29 8-30 8-31 8-32 8-33 8-34 8-35 8-36 8-37 8-38 Tables 1-1 1-2 1-3 1-4 1-5 1-6 1-7 1-8 2-1 2-2 2-3 2-4 2-5 2-6 2-7 2-8 2-9 2-10 2-11 2-12 2-13 2-14 2-15 2-16 34 Tape and Reel Pin 1 Location ............................................................................... 274 Mobile PCH Package Drawing ............................................................................... 275 G3 w/RTC Loss to S4/S5 (With Deep Sx Support) Timing Diagram ............................ 303 G3 w/RTC Loss to S4/S5 (Without Deep Sx Support) Timing Diagram ....................... 303 S5 to S0 Timing Diagram .................................................................................... 304 S3/M3 to S0 Timing Diagram ............................................................................... 305 S5/M-Off - S5/M3 Timing Diagram........................................................................ 305 S0 to S5 Timing Diagram .................................................................................... 306 S3/S4/S5 to Deep Sx to G3 w/ RTC Loss Timing Diagram ........................................ 307 G3 to Deep Sx Timing Diagram ............................................................................ 307 Clock Cycle Time................................................................................................ 308 Transmitting Position (Data to Strobe) .................................................................. 308 DRAMPWROK Timing Diagram.............................................................................. 308 Clock Timing...................................................................................................... 309 Valid Delay from Rising Clock Edge ....................................................................... 309 Setup and Hold Times......................................................................................... 309 Float Delay........................................................................................................ 309 Pulse Width ....................................................................................................... 310 Output Enable Delay........................................................................................... 310 USB Rise and Fall Times ...................................................................................... 310 USB Jitter ......................................................................................................... 311 USB EOP Width .................................................................................................. 311 SMBus / SMLink Transaction ................................................................................ 311 SMBus / SMLink Timeout..................................................................................... 312 SPI Timings ....................................................................................................... 312 Intel(R) High Definition Audio (Intel(R) HD Audio) Input and Output Timings .................. 313 Dual Channel Interface Timings............................................................................ 313 Dual Channel Interface Timings............................................................................ 313 LVDS Load and Transition Times .......................................................................... 314 Transmitting Position (Data to Strobe) .................................................................. 314 PCI Express* Transmitter Eye .............................................................................. 314 PCI Express* Receiver Eye .................................................................................. 315 Measurement Points for Differential Waveforms...................................................... 316 PCH Test Load ................................................................................................... 317 Controller Link Receive Timings............................................................................ 317 Controller Link Receive Slew Rate......................................................................... 317 PCH Suspend Well Ramp Up/Down Requirement..................................................... 317 Sequencing Requirements between PCH VCCSUS (1.05V) and External USB Vbus ....... 318 Sequencing Requirements between PCH VCC3_3 and VCC Core Rail .......................... 318 Sequencing Requirements between PCH VCC1_5 and VCC Core Rail .......................... 318 Industry Specifications..........................................................................................41 Desktop Intel(R) 8 Series Chipset Family SKUs...........................................................52 Intel(R) 8 Series/C220 Series Chipset Family PCH SKUs Flexible I/O Map .......................53 Mobile Intel(R) 8 Series Chipset Family SKUs .............................................................54 Intel(R) 8 Series/C220 Series Chipset Family PCH SKUs Flexible I/O Map .......................55 Server / Workstation Intel(R) C220 Series Chipset Family SKUs....................................55 Server / Workstation Intel(R) C220 Series Chipset Family SKUs Flexible I/O Map ............56 PCH Device and Revision ID Table ..........................................................................57 I/O Flexibility Signal Mapping.................................................................................62 USB Interface Signals ...........................................................................................63 PCI Express* Signals ............................................................................................66 Serial ATA Interface Signals...................................................................................67 Clock Interface Signals .........................................................................................69 Real Time Clock Interface......................................................................................70 Interrupt Signals ..................................................................................................71 Processor Interface Signals....................................................................................72 Direct Media Interface Signals................................................................................72 Intel(R) Flexible Display Interface (Intel(R) FDI) Signals ................................................73 Analog Display Interface Signals ............................................................................73 Digital Display Signals ..........................................................................................73 Embedded DisplayPort* (eDP*) backlight control signals ...........................................74 Intel(R) High Definition Audio (Intel(R) HD Audio) Link Signals .......................................74 Low Pin Count (LPC) Interface Signals.....................................................................75 General Purpose I/O Signals ..................................................................................76 Datasheet 2-17 2-18 2-19 2-20 2-21 2-22 2-23 2-24 2-25 2-26 2-27 2-28 2-29 2-30 3-1 3-2 3-3 4-1 4-2 4-3 4-4 5-1 5-2 5-3 5-4 5-5 5-6 5-7 5-8 5-9 5-10 5-11 5-12 5-13 5-14 5-15 5-16 5-17 5-18 5-19 5-20 5-21 5-22 5-23 5-24 5-25 5-26 5-27 5-28 5-29 5-30 5-31 5-32 5-33 5-34 5-35 5-36 5-37 5-38 5-39 5-40 5-41 5-42 5-43 5-44 5-45 5-46 Datasheet Functional Strap Definitions................................................................................... 82 SMBus Interface Signals ....................................................................................... 84 System Management Interface Signals ................................................................... 85 Controller Link Signals.......................................................................................... 85 Serial Peripheral Interface (SPI) Signals.................................................................. 85 MGPIO Conversion Table....................................................................................... 86 Client Manageability Signals .................................................................................. 87 Server Manageability Signals................................................................................. 87 Power Management Interface Signals ..................................................................... 87 Power and Ground Signals .................................................................................... 90 Thermal Signals................................................................................................... 91 Miscellaneous Signals ........................................................................................... 92 Testability Signals................................................................................................ 93 Test Pins ............................................................................................................ 93 Integrated Pull-Up and Pull-Down Resistors ............................................................. 95 Output Signals - Power Plane and States in Desktop, Mobile, and Server Configurations 98 Input Signals - Power Plane and States in Desktop and Mobile Configurations............ 103 PCH Clock Inputs ............................................................................................... 107 Clock Outputs ................................................................................................... 108 PCH PLLs .......................................................................................................... 109 Modulator Blocks ............................................................................................... 109 PCI Express* Ports 1 thru 4 - Supported Configurations .......................................... 114 PCI Express* Ports 5 thru 8 - Supported Configurations .......................................... 114 MSI versus PCI IRQ Actions................................................................................. 114 LAN Mode Support ............................................................................................. 121 LPC Cycle Types Supported ................................................................................. 127 Start Field Bit Definitions .................................................................................... 127 Cycle Type Bit Definitions ................................................................................... 127 Transfer Size Bit Definition.................................................................................. 128 SYNC Bit Definition ............................................................................................ 128 DMA Transfer Size ............................................................................................. 132 Address Shifting in 16-Bit I/O DMA Transfers......................................................... 132 Counter Operating Modes ................................................................................... 138 Interrupt Controller Connections .......................................................................... 139 Interrupt Status Registers................................................................................... 140 Content of Interrupt Vector Byte .......................................................................... 141 APIC Interrupt Mapping1 .................................................................................... 146 Stop Frame Explanation...................................................................................... 149 Data Frame Format ............................................................................................ 149 Configuration Bits Reset by RTCRST# Assertion ..................................................... 152 INIT# Going Active ............................................................................................ 153 NMI Sources ..................................................................................................... 154 General Power States for Systems Using the PCH ................................................... 155 State Transition Rules for the PCH........................................................................ 156 System Power Plane........................................................................................... 157 Causes of SMI and SCI ....................................................................................... 158 Sleep Types ...................................................................................................... 162 Causes of Wake Events....................................................................................... 163 GPI Wake Events ............................................................................................... 164 Transitions Due to Power Failure .......................................................................... 165 Supported Deep Sx Policy Configurations .............................................................. 165 Deep Sx Wake Events ........................................................................................ 166 Transitions Due to Power Button .......................................................................... 166 Transitions Due to RI# Signal.............................................................................. 168 Write Only Registers with Read Paths in ALT Access Mode ....................................... 170 PIC Reserved Bits Return Values .......................................................................... 171 Register Write Accesses in ALT Access Mode .......................................................... 172 SUSPWRDNACK/SUSWARN#/GPIO30 Pin Behavior ................................................. 175 SUSPWRDNACK during Reset .............................................................................. 175 Causes of Host and Global Resets ........................................................................ 177 Event Transitions that Cause Messages................................................................. 181 SATA Feature Support ........................................................................................ 186 SATA Features................................................................................................... 187 Message Format ................................................................................................ 194 Multi-activity LED Message Type .......................................................................... 195 Legacy Replacement Routing ............................................................................... 198 EHC Resets ....................................................................................................... 201 35 5-47 5-48 5-49 5-50 5-51 5-52 5-53 5-54 5-55 5-56 5-57 5-58 5-59 5-60 5-61 5-62 5-63 5-64 6-1 6-2 8-1 8-2 8-3 8-4 8-5 8-6 8-7 8-8 8-9 8-10 8-11 8-12 8-13 8-14 8-15 8-16 8-17 8-18 8-19 8-20 8-21 8-22 8-23 8-24 8-25 8-26 8-27 8-28 8-29 8-30 8-31 8-32 8-33 8-34 9-1 9-2 9-3 9-4 9-5 10-1 11-1 11-2 12-1 36 Debug Port Behavior........................................................................................... 205 I2C* Block Read................................................................................................. 215 Enable for SMBALERT# ....................................................................................... 218 Enables for SMBus Slave Write and SMBus Host Events ........................................... 218 Enables for the Host Notify Command ................................................................... 218 Slave Write Registers.......................................................................................... 220 Command Types ................................................................................................ 220 Slave Read Cycle Format..................................................................................... 221 Data Values for Slave Read Registers.................................................................... 221 Host Notify Format ............................................................................................. 223 PCH Thermal Throttle States (T-states) ................................................................. 226 PCH Thermal Throttling Configuration Registers...................................................... 226 Region Size versus Erase Granularity of Flash Components ...................................... 239 Region Access Control Table ................................................................................ 241 Hardware Sequencing Commands and Opcode Requirements ................................... 244 Flash Protection Mechanism Summary .................................................................. 245 Recommended Pinout for 8-Pin Serial Flash Device ................................................. 246 Recommended Pinout for 16-Pin Serial Flash Device ............................................... 247 Desktop/Server PCH Ballout By Signal Name.......................................................... 258 Mobile PCH Ballout by Signal Name....................................................................... 266 Storage Conditions and Thermal Junction Operating Temperature Limits.................... 276 Mobile Thermal Design Power .............................................................................. 276 PCH Absolute Maximum Ratings ........................................................................... 277 PCH Power Supply Range .................................................................................... 277 Measured Silicon ICC9 (Desktop and Mobile)........................................................... 278 Single-Ended Signal DC Characteristics as Inputs or Outputs.................................... 279 Differential Signal DC Characteristics .................................................................... 284 Other DC Characteristics ..................................................................................... 286 Signal Groups .................................................................................................... 287 CRT DAC Signal Group DC Characteristics: Functional Operating Range (VccADAC = 3.3 V 5%)..................................................................................... 287 Display Port Auxiliary Signal Group DC Characteristics............................................. 288 PCI Express* Interface Timings ............................................................................ 288 HDMI* Interface Timings (DDP[D:B][3:0]) ............................................................ 289 Intel(R) SDVO Interface Timings ............................................................................ 289 DisplayPort* Interface Timings (DDP[D:B][3:0]) .................................................... 290 DisplayPort* Aux Interface .................................................................................. 290 DDC Characteristics - DDC Signals: VGA_DDC_CLK, VGA_DDC_DATA, DDP[D:B] _CTRLCLK, DDP[D:B]_CTRLDATA ......................................................................... 290 CRT DAC AC Characteristics................................................................................. 291 Clock Timings .................................................................................................... 291 Universal Serial Bus Timing ................................................................................. 294 SATA Interface Timings....................................................................................... 295 SMBus and SMLink Timing ................................................................................... 296 Intel(R) High Definition Audio (Intel(R) HD Audio) Timing ............................................ 297 LPC Timing ........................................................................................................ 297 Miscellaneous Timings......................................................................................... 297 SPI Timings (20 MHz) ......................................................................................... 297 SPI Timings (33 MHz) ......................................................................................... 298 SPI Timings (50 MHz) ......................................................................................... 298 SST Timings (Server/Workstation Only) ................................................................ 298 Controller Link Receive Timings............................................................................ 299 USB 3.0 Interface Transmit and Receiver Timings ................................................... 299 Power Sequencing and Reset Signal Timings .......................................................... 299 Suspend Well Voltage Ramp Up/Down Requirements .............................................. 319 Core Well Voltage Ramp Up/Down Requirements .................................................... 319 PCI Devices and Functions................................................................................... 321 Fixed I/O Ranges Decoded by PCH........................................................................ 322 Variable I/O Decode Ranges ................................................................................ 324 Memory Decode Ranges from Processor Perspective ............................................... 325 SPI Mode Address Swapping ................................................................................ 327 Chipset Configuration Register Memory Map (Memory Space)................................... 329 Gigabit LAN Configuration Registers Address Map (Gigabit LAN--D25:F0)........................................................................................ 363 Gigabit LAN Capabilities and Status Registers Address Map (Gigabit LAN--MBARA) ........................................................................................ 375 LPC Interface PCI Register Address Map (LPC I/F--D31:F0)...................................... 379 Datasheet 12-2 12-3 12-4 12-5 12-6 12-7 12-8 12-9 12-10 12-11 12-12 12-13 13-1 13-2 13-3 13-4 13-5 14-1 14-1 15-1 15-1 15-2 15-3 16-1 16-1 16-2 16-3 17-1 17-1 18-1 18-1 19-1 20-1 21-1 21-1 22-1 22-1 23-1 23-1 23-2 23-3 23-4 23-5 23-6 23-7 23-8 23-9 Datasheet DMA Registers................................................................................................... 400 PIC Registers .................................................................................................... 410 APIC Direct Registers ......................................................................................... 417 APIC Indirect Registers....................................................................................... 417 RTC I/O Registers .............................................................................................. 421 RTC (Standard) RAM Bank .................................................................................. 422 Processor Interface PCI Register Address Map ....................................................... 425 Power Management PCI Register Address Map (PM--D31:F0)................................... 428 APM Register Map .............................................................................................. 437 ACPI and Legacy I/O Register Map ....................................................................... 438 TCO I/O Register Address Map............................................................................. 453 Registers to Control GPIO Address Map................................................................. 459 SATA Controller PCI Register Address Map (SATA-D31:F2)...................................... 468 Bus Master IDE I/O Register Address Map ............................................................. 492 AHCI Register Address Map ................................................................................. 499 Generic Host Controller Register Address Map........................................................ 500 Port [5:0] DMA Register Address Map ................................................................... 507 SATA Controller PCI Register Address Map (SATA-D31:F5)...................................... 521 Bus Master IDE I/O Register Address Map ............................................................. 534 USB EHCI PCI Register Address Map (USB EHCI--D29:F0, D26:F0) .......................... 541 Enhanced Host Controller Capability Registers ....................................................... 561 Enhanced Host Controller Operational Register Address Map .................................... 564 Debug Port Register Address Map ........................................................................ 575 USB xHCI PCI Register Address Map (USB xHCI--D20:F0)....................................... 579 Enhanced Host Controller Capability Registers ....................................................... 597 Enhanced Host Controller Operational Register Address Map .................................... 600 Enhanced Host Controller Operational Register Address Map .................................... 616 Intel(R) High Definition Audio (Intel(R) HD Audio) PCI Register Address Map (Intel(R) High Definition Audio D27:F0)................................................................... 622 Intel(R) High Definition Audio Memory Mapped Configuration Registers Address Map (Intel(R) High Definition Audio D27:F0) ................................................ 640 SMBus Controller PCI Register Address Map (SMBus--D31:F3)................................. 662 SMBus I/O and Memory Mapped I/O Register Address Map...................................... 668 PCI Express* Configuration Registers Address Map (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) ..................................................... 678 Memory-Mapped Register Address Map ................................................................. 716 Serial Peripheral Interface (SPI) Register Address Map (SPI Memory Mapped Configuration Registers)....................................................... 723 Gigabit LAN SPI Flash Program Register Address Map (GbE LAN Memory Mapped Configuration Registers) ............................................... 742 Thermal Sensor Register Address Map .................................................................. 752 Thermal Memory Mapped Configuration Register Address Map ................................. 759 Intel(R) MEI 1 Configuration Registers Address Map (Intel(R) MEI 1--D22:F0) ...................................................................................... 765 Intel(R) MEI 1 MMIO Register Address Map ............................................................. 775 Intel(R) MEI 2 Configuration Registers Address Map (Intel(R) MEI 2--D22:F1) ...................................................................................... 777 Intel(R) MEI 2 MMIO Register Address Map ............................................................. 786 IDE Redirect Function IDER Register Address Map .................................................. 789 IDER BAR0 Register Address Map......................................................................... 796 IDER BAR1 Register Address Map......................................................................... 805 IDER BAR4 Register Address Map......................................................................... 806 Serial Port for Remote Keyboard and Text (KT) Redirection Register Address Map ..................................................................................................... 811 KT IO/Memory Mapped Device Register Address Map.............................................. 817 37 Revision History Revision Number 001 Description * Initial Release. June 2013 * Chapter 1, "Introduction" -- Table 1-2, "Desktop Intel(R) 8 Series Chipset Family SKUs" -- Table 1-4, "Mobile Intel(R) 8 Series Chipset Family SKUs" -- Table 1-6, "Server / Workstation Intel(R) C220 Series Chipset Family SKUs" Chapter 4, "PCH and System Clocks" -- Section 4.5.2.1, "OC_WDT_CTL --Overclocking Watchdog Timer Control Register" Chapter 5, "Functional Description" -- Section 5.3, "PCI Express* Root Ports (D28:F0~F7)" -- Section 5.20.1, "Overview" Chapter 8, "Electrical Characteristics" -- Section 8.4, "General DC Characteristics", Table 8-5, Table 8-6 -- Table 8-17, "DDC Characteristics - DDC Signals: VGA_DDC_CLK, VGA_DDC_DATA, DDP[D:B] _CTRLCLK, DDP[D:B]_CTRLDATA" -- Table 8-19, "Clock Timings" -- Figure 8-35, "PCH Suspend Well Ramp Up/Down Requirement" -- Table 8-33, "Suspend Well Voltage Ramp Up/Down Requirements" Chapter 10, "Chipset Configuration Registers" -- Section 10.1.41, "PM_CFG--Power Management Configuration Register" Chapter 12, "LPC Interface Bridge Registers (D31:F0)" -- Section 12.6.1, "I/O Register Address Map" -- Section 12.8.3.5, "GPE0_STS--General Purpose Event 0 Status Register" -- Section 12.10.3, "GP_LVL--GPIO Level for Input or Output Register" Chapter 19, "PCI Express* Configuration Registers" -- Section 19.1.29, "LCTL--Link Control Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/ F6/F7)" Chapter 21, "Serial Peripheral Interface (SPI)" -- Section 21.1.29, "PTINX--Flash Parameter Table Index Register" -- Section 21.1.30, "PTDATA--Flash Parameter Table Data Register" September 2013 Chapter 1, "Introduction" -- Updated sub-section "Intel(R) High Definition Audio (Intel(R) HD Audio) Controller" -- Updated Section 1.3, "Intel(R) 8 Series/C220 Series Chipset Family PCH SKU Definition" Chapter 2, "Signal Description" -- Corrected Table 2-16, "General Purpose I/O Signals" Chapter 5, "Functional Description" -- Updated Section 5.3.5, "Hot-Plug" -- Removed Section 5.17.6, "Function Level Reset Support (FLR)" Chapter 8, "Electrical Characteristics" -- Updated notes for Table 8-4. Chapter 9, "Register and Memory Mapping" -- Updated Table 9-5, "SPI Mode Address Swapping" Chapter 10, "Chipset Configuration Registers" -- Corrected SECRR50 bits 27:24 settings for SATA Gen3 Rx Equalization 1 - mSATA 4"-6" and 6"-8" -- Corrected SECRR54 bits 3:0 settings for SATA Gen2 Rx Equalization 1 - M.2 (NGFF) <2", 2"-4" and 4"-6" -- Changed the Topology name from "iSATA (DT Direct Connect)" to "Internal SATA (Cable Connect)" for SECRR50, and SECRR54 SATA Rx Equalization 1 tables. Chapter 19, "PCI Express* Configuration Registers" -- Added Section 19.1.54, "PECR4--PCI Express* Configuration Register 4 (PCI Express*-- D28:F0/F1/F2/F3/F4/F5)" Chapter 23, "Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0])" -- Corrected Table 23-1, "Intel(R) MEI 1 Configuration Registers Address Map (Intel(R) MEI 1--D22:F0)" Minor updates throughout for clarity. May 2014 * * * 002 * * * * * * * * * 003 * * * * 38 Revision Date Datasheet Platform Controller Hub Features Direct Media Interface -- Up to 20 Gb/s each direction, full duplex. -- Transparent to software NEW: Flexible IO -- A new architecture that allows some high speed IO signals to be configured as SATA or USB 3.0 or PCIe PCI Express* -- Up to eight PCI Express root ports -- Supports PCI Express Rev 2.0 running at up to 5.0 GT/s -- Ports 1-4 and 5-8 can independently be configured to support multiple port configurations -- Module based Hot-Plug supported (that is, ExpressCard*) -- NEW: Latency Tolerance Reporting Integrated Serial ATA Host Controller -- Up to six SATA ports -- Data transfer rates supported: 6.0 Gb/s, 3.0 Gb/s, and 1.5 Gb/s on all ports -- Integrated AHCI controller External SATA support on all ports -- 3.0 Gb/s and 1.5 Gb/s support -- Port Disable Capability Intel(R) Rapid Storage Technology (Intel(R) RST) -- Configures the PCH SATA controller as a RAID controller supporting RAID 0/1/5/10 Intel(R) Smart Response Technology Intel(R) High Definition Audio Interface -- PCI Express endpoint -- Independent Bus Master logic for eight general purpose streams: four input and four output -- Support four external Codecs -- Supports variable length stream slots -- Supports multichannel, 32-bit sample depth, 192 kHz sample rate output -- Provides mic array support -- Allows for non-48 kHz sampling output -- Support for ACPI Device States -- Low Voltage Eight TACH signals and Four PWM signals (Server and Workstation Only) Platform Environmental Control Interface (PECI) and Simple Serial Transport (SST) 1.0 Bus (Server and Workstation Only) Datasheet USB -- xHCI Host Controller, supports up to 6 SuperSpeed USB 3.0 connections and 14 USB 2.0 connections -- More flexibility in pairing USB 3.0 and USB 2.0 signals to the same connector -- Two EHCI Host Controllers, supporting up to fourteen external USB 2.0 ports -- Support for dynamic power gating and Intel(R) Power Management Framework (PMF) -- Per-Port-Disable Capability -- Includes up to two USB 2.0 High-speed Debug Ports -- Supports wake-up from sleeping states S1S4 Integrated Gigabit LAN Controller -- Connection utilizes PCI Express pins -- Integrated ASF Management Controller -- Network security with System Defense -- Supports IEEE 802.3 -- 10/100/1000 Mbps Ethernet Support -- Jumbo Frame Support Intel(R) Active Management Technology with System Defense -- Network Outbreak Containment Heuristics Intel(R) IO Virtualization (Intel(R) VT-d) Support Intel(R) Trusted Execution Technology (Intel(R) TXT) Support Intel(R) Anti-Theft Technology (Intel(R) AT) Power Management Logic -- Supports ACPI 4.0a -- ACPI-defined power states (processor driven C states) -- ACPI Power Management Timer -- SMI# generation -- All registers readable/restorable for proper resume from 0 V core well suspend states -- Support for APM-based legacy power management for non-ACPI implementations Integrated Clock Controller -- Full featured platform clocking without need for a discrete clock chip -- 8 PCIe* 2.0 specification compliant clocks, 4 PCIe 3.0 specification compliant clocks, five 33 MHz PCI clocks, four Flex Clocks that can be configured for various frequencies, and two 135 MHz clocks for DisplayPort*. 39 External Glue Integration -- Integrated Pull-down and Series resistors on USB Enhanced DMA Controller -- Two cascaded 8237 DMA controllers -- Supports LPC DMA SMBus -- Interface speeds of up to 100 kbps -- Supports SMBus 2.0 Specification -- Host interface allows processor to communicate using SMBus -- Slave interface allows an internal or external microcontroller to access system resources -- Supports most two-wire components that are also I2C compatible SMLink -- Provides independent manageability bus through SMLink0 and SMLink1 -- SMLink0 dedicated to LAN PHY and NFC, operating up to 1 MHz -- SMLink1 dedicated to EC or BMC, operating up to 100 kHz High Precision Event Timers -- Advanced operating system interrupt scheduling Timers Based on 8254 -- System timer, Refresh request, Speaker tone output Real-Time Clock -- 256 byte battery-backed CMOS RAM -- Integrated oscillator components -- Lower Power DC/DC Converter implementation System TCO Reduction Circuits -- Timers to generate SMI# and Reset upon detection of system hang -- Timers to detect improper processor reset -- Supports ability to disable external devices JTAG -- Boundary Scan for testing during board manufacturing Note: Serial Peripheral Interface (SPI) -- Supports up to two SPI devices -- Supports 20 MHz, 33 MHz, and 50 MHz SPI devices -- NEW: Supports Quad IO Fast Read, Quad Output Fast Read, Dual IO Fast Read -- NEW: Support for TPM over SPI with the addition of SPI_CS2# chip select pin -- NEW: Supports Serial Flash Discoverable Parameter (SFDP) -- Support up to two different erase granularities Firmware Hub I/F supports BIOS Memory size up to 8 MB Low Pin Count (LPC) I/F -- Supports two Master/DMA devices. -- Support for Security Device (Trusted Platform Module) connected to LPC Interrupt Controller -- Supports up to eight legacy interrupt pins -- Supports PCI 2.3 Message Signaled Interrupts -- Two cascaded 8259 with 15 interrupts -- Integrated IO APIC capability with 24 interrupts -- Supports Processor System Bus interrupt delivery 1.05 V operation with tolerance up to 3.3 V IO 1.05 V Core Voltage Integrated Voltage Regulators for select power rails GPIO -- Open-Drain, Inversion -- GPIO lock down Intel(R) Flexible Display Interface Display -- Analog Display (VGA) Interface -- Side band signals AUX CH, DDC and HPD -- Backlight Control and Panel Power sequencing signals Package -- 23 mm x 22 mm FCBGA (Desktop Only) -- 20 mm x 20 mm FCBGA (Mobile Only) Not all features are available on all PCH SKUs. 40 Datasheet Introduction 1 Introduction 1.1 About This Manual This document is intended for Original Equipment Manufacturers and BIOS vendors creating products based on the Intel(R) 8 Series/C220 Series Chipset Family Platform Controller Hub (PCH) (See Section 1.3 for SKU definitions and supported features). Note: Throughout this document, Platform Controller Hub (PCH) is used as a general term and refers to all Intel(R) 8 Series/C220 Series Chipset Family PCH SKUs, unless specifically noted otherwise. Note: Throughout this document, the terms "Desktop" and "Desktop Only" refer to information that is applicable only to Desktop PCH, unless specifically noted otherwise. Note: Throughout this document, the terms "Server/Workstation" and "Server/Workstation Only" refers to information that is applicable only to Server/Workstation PCH, unless specifically noted otherwise. Note: Throughout this document, the terms "Mobile" and "Mobile Only" refers to information that is applicable only to the Mobile PCH, unless specifically noted otherwise. This manual assumes a working knowledge of the vocabulary and principles of PCI Express*, USB, AHCI, SATA, Intel(R) High Definition Audio (Intel(R) HD Audio), SMBus, ACPI and Low Pin Count (LPC). Although some details of these features are described within this manual, refer to the individual industry specifications listed in Table 1-1 for the complete details. All PCI buses, devices, and functions in this manual are abbreviated using the following nomenclature; Bus:Device:Function. This manual abbreviates buses as Bn, devices as Dn and functions as Fn. For example Device 31 Function 0 is abbreviated as D31:F0, Bus 1 Device 8 Function 0 is abbreviated as B1:D8:F0. Generally, the bus number will not be used, and can be considered to be Bus 0. Table 1-1. Industry Specifications (Sheet 1 of 2) Specification Location PCI Express* Base Specification, Revision 2.0 http://www.pcisig.com/specifications Low Pin Count Interface Specification, Revision 1.1 (LPC) http://developer.intel.com/design/chipsets/industry/ lpc.htm System Management Bus Specification, Version 2.0 (SMBus) http://www.smbus.org/specs/ PCI Local Bus Specification, Revision 2.3 (PCI) http://www.pcisig.com/specifications PCI Power Management Specification, Revision 1.2 http://www.pcisig.com/specifications Universal Serial Bus Specification (USB), Revision 2.0 http://www.usb.org/developers/docs Universal Serial Bus Specification (USB), Revision 3.0 http://www.usb.org/developers/docs Advanced Configuration and Power Interface, Version 4.0a (ACPI) http://www.acpi.info/spec.htm Enhanced Host Controller Interface Specification for Universal Serial Bus, Revision 1.0 (EHCI) http://developer.intel.com/technology/usb/ehcispec.htm eXtensible Host Controller Interface for Universal Serial Bus (xHCI), Revision 1.0 http://www.intel.com/technology/usb/xhcispec.htm Datasheet 41 Introduction Table 1-1. Industry Specifications (Sheet 2 of 2) Specification Location Serial ATA Specification, Revision 3.0 http://www.serialata.org/ Serial ATA II: Extensions to Serial ATA 1.0, Revision 1.0 http://www.serialata.org Serial ATA II Cables and Connectors Volume 2 Gold http://www.serialata.org Alert Standard Format Specification, Version 1.03 http://www.dmtf.org/standards/asf IEEE 802.3 Fast Ethernet http://standards.ieee.org/getieee802/ AT Attachment - 6 with Packet Interface (ATA/ATAPI - 6) http://T13.org (T13 1410D) IA-PC HPET (High Precision Event Timers) Specification, Revision 1,0a http://www.intel.com/hardwaredesign/hpetspec_1.pdf Trusted Platform Module (TPM) Specification 1.3 Note: TPM over SPI supports 8 bytes transactions max. (R) Intel Virtualization Technology http://www.trustedcomputinggroup.org/specs/TPM SFF-8485 Specification for Serial GPIO (SGPIO) Bus, Revision 0.7 http://www.intel.com/technology/virtualization/ index.htm Advanced Host Controller Interface specification for Serial ATA, Revision 1.3 http://www.intel.com/technology/serialata/ahci.htm Intel(R) High Definition Audio Specification, Revision 1.0a http://www.intel.com/standards/hdaudio/ 1.1.1 http://www.intel.com/technology/virtualization/ index.htm Chapter Descriptions Chapter 1, "Introduction" Chapter 1 introduces the PCH, provides information on the organization of the manual and gives a general overview of the PCH. Chapter 2, "Signal Description" Chapter 2 provides a block diagram of the PCH and a detailed description of each signal. Signals are arranged according to interface and details are provided as to the drive characteristics (Input/Output, Open Drain, and so on) of all signals. Chapter 3, "PCH Pin States" Chapter 3 provides a complete list of signals, their associated power well, their logic level in each suspend state, and their logic level before and after reset. Chapter 4, "PCH and System Clocks" Chapter 4 provides a list of each clock domain associated with the PCH. Chapter 5, "Functional Description" Chapter 5 provides a detailed description of the functions in the PCH. Chapter 6, "Ballout Definition" Chapter 6 provides the ball assignment table and the ball-map for the Desktop and Mobile packages. Chapter 7, "Package Information" Chapter 7 provides drawings of the physical dimensions and characteristics of the Desktop and Mobile packages. Chapter 8, "Electrical Characteristics" Chapter 8 provides all AC and DC characteristics including detailed timing diagrams. 42 Datasheet Introduction Chapter 9, "Register and Memory Mapping" Chapter 9 provides an overview of the registers, fixed I/O ranges, variable I/O ranges and memory ranges decoded by the PCH. Chapter 10, "Chipset Configuration Registers" Chapter 10 provides a detailed description of registers and base functionality that is related to chipset configuration. It contains the root complex register block, which describes the behavior of the upstream internal link. Chapter 11, "Gigabit LAN Configuration Registers" Chapter 11 provides a detailed description of registers that reside in the PCH's integrated LAN controller. The integrated LAN Controller resides at Device 25, Function 0 (D25:F0). Chapter 12, "LPC Interface Bridge Registers (D31:F0)" Chapter 12 provides a detailed description of registers that reside in the LPC bridge. This bridge resides at Device 31, Function 0 (D31:F0). This function contains registers for many different units within the PCH including DMA, Timers, Interrupts, Processor Interface, GPIO, Power Management, System Management and RTC. Chapter 13, "SATA Controller Registers (D31:F2)" Chapter 13 provides a detailed description of registers that reside in the SATA controller #1. This controller resides at Device 31, Function 2 (D31:F2). Chapter 14, "PCI Configuration Registers (SATA-D31:F5)" Chapter 14.1 provides a detailed description of registers that reside in the SATA controller #2. This controller resides at Device 31, Function 5 (D31:F5). Chapter 15, "EHCI Controller Registers (D29:F0, D26:F0)" Chapter 15 provides a detailed description of registers that reside in the two EHCI host controllers. These controllers reside at Device 29, Function 0 (D29:F0) and Device 26, Function 0 (D26:F0). Chapter 16, "xHCI Controller Registers (D20:F0)" Chapter 16 provides a detailed description of registers that reside in the xHCI. This controller resides at Device 20, Function 0 (D20:F0). Chapter 17, "Integrated Intel(R) High Definition Audio (Intel(R) HD Audio) Controller Registers" Chapter 17 provides a detailed description of registers that reside in the Intel High Definition Audio controller. This controller resides at Device 27, Function 0 (D27:F0). Chapter 18, "SMBus Controller Registers (D31:F3)" Chapter 18 provides a detailed description of registers that reside in the SMBus controller. This controller resides at Device 31, Function 3 (D31:F3). Chapter 19, "PCI Express* Configuration Registers" Chapter 19 provides a detailed description of registers that reside in the PCI Express controller. This controller resides at Device 28, Functions 0 to 7 (D28:F0-F7). Chapter 20, "High Precision Event Timer Registers" Chapter 20 provides a detailed description of registers that reside in the multi-media timer memory mapped register space. Chapter 21, "Serial Peripheral Interface (SPI)" Chapter 21 provides a detailed description of registers that reside in the SPI memory mapped register space. Datasheet 43 Introduction Chapter 22, "Thermal Sensor Registers (D31:F6)" Chapter 22 provides a detailed description of registers that reside in the thermal sensors PCI configuration space. The registers reside at Device 31, Function 6 (D31:F6). Chapter 23, "Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0])" Chapter 23 provides a detailed description of registers that reside in the Intel ME controller. The registers reside at Device 22, Function 0 (D22:F0). 1.2 Overview The PCH provides extensive I/O support. Functions and capabilities include: * PCI Express* Base Specification, Revision 2.0 support for up to eight ports with transfers up to 5 GT/s * ACPI Power Management Logic Support, Revision 4.0a * Enhanced DMA controller, interrupt controller, and timer functions * Integrated Serial ATA host controllers with independent DMA operation on up to six ports * xHCI USB controller provides support for up to 14 USB ports, of which six can be configured as SuperSpeed USB 3.0 ports. * Two legacy EHCI USB controllers each provides a USB debug port. * Flexible I/O, A new architecture to allow some high speed I/O signals to be configured as PCIe, SATA or USB 3.0. * Integrated 10/100/1000 Gigabit Ethernet MAC with System Defense * System Management Bus (SMBus) Specification, Version 2.0 with additional support for I2C devices * Supports Intel(R) High Definition Audio (Intel(R) HD Audio) * Supports Intel(R) Rapid Storage Technology (Intel(R) RST) * Supports Intel(R) Active Management Technology (Intel(R) AMT) * Supports Intel(R) Virtualization Technology for Directed I/O (Intel(R) VT-d) * Supports Intel(R) Trusted Execution Technology (Intel(R) TXT) * Integrated Clock Controller * Intel(R) Flexible Display Interface (Intel(R) FDI) * Analog VGA Display Interface * Low Pin Count (LPC) interface * Firmware Hub (FWH) interface support * Serial Peripheral Interface (SPI) support * Intel(R) Anti-Theft Technology (Intel(R) AT) * JTAG Boundary Scan support Note: 44 Not all functions and capabilities may be available on all SKUs. See Section 1.3 for details on SKU feature availability. Datasheet Introduction 1.2.1 Capability Overview The following sub-sections provide an overview of the PCH capabilities. Direct Media Interface (DMI) Direct Media Interface (DMI) is the chip-to-chip connection between the processor and PCH. This high-speed interface integrates advanced priority-based servicing allowing for concurrent traffic and true isochronous transfer capabilities. Base functionality is completely software-transparent, permitting current and legacy software to operate normally. Intel(R) Flexible Display Interface (Intel(R) FDI) Intel FDI connects the display engine in the processor with the Analog display interface on the PCH. The display data for Analog VGA panels from the frame buffer is processed by the display engine and sent to the PCH through Intel FDI. Intel FDI has two lanes for display data transfer to the PCH from the processor. Each Intel FDI lane consists of two differential signal receive pairs supporting a data rate of 2.7 Gb/s. PCH Display Interface The Analog VGA display interface is the only display interface supported on the PCH. This interface is used to drive legacy CRT panels and advanced LCD VGA panels. The analog VGA display interface has an integrated RAMDAC 180 MHz, driving a standard progressive scan analog monitor to a resolution of up to 1920x2000 pixels and 24-bit color at a 60 Hz refresh rate with reduced blanking. Analog VGA display interface is in the PCH, although the main display engine is in the processor. Thus, the Intel FDI is used to send the display data to the PCH. Intel FDI is a bus that connects the processor and PCH display components. The PCH, upon receiving the display data, transcodes the data as per the display technology protocol and sends the data through the DAC to display panel. The PCH integrates digital display side band signals, even though digital display interfaces are in the processor. There are three pairs of AUX CH, DDC Clock/Data, and Hot-Plug Detect Signals on the PCH that correspond to digital display interface/ports B, C, and D. The PCH also integrates panel backlight control signals, which are used only when Embedded DisplayPort* (eDP) is configured on the platform. PCI Express* Interface The PCH provides up to 8 PCI Express Root Ports, supporting the PCI Express Base Specification, Revision 2.0. Each Root Port x1 lane supports up to 5 Gb/s bandwidth in each direction (10 Gb/s concurrent). PCI Express Root Ports 1-4 or Ports 5-8 can independently be configured to support multiple port width configurations. See Section 1.3 for details on feature availability. Datasheet 45 Introduction Serial ATA (SATA) Controller The PCH has two integrated SATA host controllers that support independent DMA operation on up to six ports and support data transfer rates of up to 6.0 Gb/s on all ports. The SATA controller contains two modes of operation - a legacy mode using I/O space, and an AHCI mode using memory space. Software that uses legacy mode will not have AHCI capabilities. The PCH supports the Serial ATA Specification, Revision 3.0. The PCH also supports several optional sections of the Serial ATA II: Extensions to Serial ATA 1.0 Specification, Revision 1.0 (AHCI support is required for some elements). See Section 1.3 for details on feature availability. Advanced Host Controller Interface (AHCI) The PCH provides hardware support for Advanced Host Controller Interface (AHCI), a standardized programming interface for SATA host controllers. Platforms supporting AHCI may take advantage of performance features such as no master/slave designation for SATA devices - each device is treated as a master - and hardwareassisted native command queuing. AHCI also provides usability enhancements, such as Hot-Plug. AHCI requires appropriate software support (such as, an AHCI driver) and for some features, hardware support in the SATA device or additional platform hardware. See Section 1.3 for details on SKU feature availability. Intel(R) Rapid Storage Technology (Intel(R) RST) The PCH provides support for Intel Rapid Storage Technology (Intel RST), providing both AHCI (see above for details on AHCI) and integrated RAID functionality. The RAID capability provides high-performance RAID 0, 1, 5, and 10 functionality on up to 6 SATA ports of the PCH. Matrix RAID support is provided to allow multiple RAID levels to be combined on a single set of hard drives, such as RAID 0 and RAID 1 on two disks. Other RAID features include hot spare support, SMART alerting, and RAID 0 auto replace. Software components include an Option ROM for pre-boot configuration and boot functionality, a Microsoft* Windows* compatible driver, and a user interface for configuration and management of the RAID capability of PCH. See Section 1.3 for details on SKU feature availability. Intel(R) Smart Response Technology Intel Smart Response Technology is a disk caching solution that can provide improved computer system performance with improved power savings. It allows configuration of a computer system with the advantage of having HDDs for maximum storage capacity with system performance at or near SSD performance levels. See Section 1.3 for details on SKU feature availability. Low Pin Count (LPC) Interface The PCH implements an LPC Interface as described in the LPC 1.1 Specification. The Low Pin Count (LPC) bridge function of the PCH is mapped as PCI D31:F0 and supports a memory size up to 8 MB, two master/DMA devices, interrupt controllers, timers, power management, system management, Super I/O, and RTC. 46 Datasheet Introduction Serial Peripheral Interface (SPI) In addition to the standard Dual Output Fast Read mode, the SPI interface in the PCH supports new Dual I/O Fast Read, Quad I/O Fast Read and Quad Output Fast Read. To enable the new Quad I/O operation modes, all data transfer signals in the interface are bidirectional and two new signals (SPI_IO2 and SPI_IO3) have been added to the basic four-wire interface: Clock, Master Out Slave In (MOSI), Master In Slave Out (MISO) and active-low chip selects (CS#). The PCH supports three chip selects: SPI_CS0# and SPI_CS1# are used to access two separate SPI Flash components in Descriptor Mode. SPI_CS2# is dedicated only to support Trusted Platform Module (TPM) on SPI (TPM can be configured through PCH soft straps to operate over LPC or SPI, but no more than 1 TPM is allowed in the system). SPI_CS2# may not be used for any purpose other than TPM. The SPI Flash Controller supports running instructions at 20 MHz, 33 MHz, and 50 MHz, and can be used by the PCH for BIOS code, to provide chipset configuration settings, internal micro-processor code, integrated Gigabit Ethernet MAC/PHY configuration, and Intel Active Management Technology (Intel(R) AMT) settings. The SPI Flash Controller supports the Serial Flash Discoverable Parameter (SFDP) JEDEC standard that provides a consistent way of describing the functional and feature capabilities of serial flash devices in a standard set of internal parameter tables. The SPI Flash Controller queries these parameter tables to discover the attributes to enable divergent features from multiple SPI part vendors, such as Quad I/O Fast Read capabilities or device storage capacity, among others. Compatibility Modules (DMA Controller, Timer/Counters, Interrupt Controller) The DMA controller incorporates the logic of two 8237 DMA controllers, with seven independently programmable channels. Channels 0-3 are hardwired to 8-bit, count-bybyte transfers, and channels 5-7 are hardwired to 16-bit, count-by-word transfers. Any two of the seven DMA channels can be programmed to support fast Type-F transfers. Channel 4 is reserved as a generic bus master request. The PCH supports LPC DMA, which is similar to ISA DMA, through the PCH DMA controller. LPC DMA is handled through the use of the LDRQ# lines from peripherals and special encoding on LAD[3:0] from the host. Single, Demand, Verify, and Increment modes are supported on the LPC interface. The timer/counter block contains three counters that are equivalent in function to those found in one 8254 programmable interval timer. These three counters are combined to provide the system timer function, and speaker tone. The 14.318 MHz oscillator input provides the clock source for these three counters. The PCH provides an ISA-compatible Programmable Interrupt Controller (PIC) that incorporates the functionality of two 8259 interrupt controllers. The two interrupt controllers are cascaded so that 14 external and two internal interrupts are possible. In addition, the PCH supports a serial interrupt scheme. All of the registers in these modules can be read and restored. This is required to save and restore system state after power has been removed and restored to the platform. Advanced Programmable Interrupt Controller (APIC) In addition to the standard ISA-compatible Programmable Interrupt controller (PIC) described in the previous section, the PCH incorporates the Advanced Programmable Interrupt Controller (APIC). Datasheet 47 Introduction Universal Serial Bus (USB) Controllers The PCH contains one eXtensible Host Controller Interface (xHCI) controller and two Enhanced Host Controller Interface (EHCI) controllers. The xHCI controller is mapped as PCI D20:F0 and it supports up to 14 USB 2.0 ports of which 6 can be configured as SuperSpeed (USB 3.0) ports. EHCI controller 1 (EHCI1) is located at D29:F0 and it supports up to 8 USB 2.0 ports. EHCI controller 2 (EHCI2) is located at D26:F0 and it supports up to 6 USB 2.0 ports. One of the USB 2.0 ports in either EHCI controller can be used for a Debug Port (not available through xHCI). Note: USB 2.0 differential pairs are numbered starting with 0. USB 3.0 differential pairs are numbered starting with 1. Note: Regarding the optional USB Battery Charging Specification 1.x: Intel does not have a topology for Intel(R) 8 Series/C220 Series Chipset Family based platforms that can accommodate USB battery charging circuits robustly across the large install base of USB cables and High Speed (HS) devices. As such, Intel does not recommend that platforms exceed native supply currents defined in the USB specification for USB 2.0 ports. See Section 1.3 for details on feature availability. Flexible I/O The PCH implements Flexible I/O, an architecture to allow some high speed signals to be configured as SATA, USB 3.0, or PCIe signals. Through soft straps, the functionality on these multiplexed signals are selected to meet the I/O needs on the platform. See Section 5.22 for details on Flexible I/O. Gigabit Ethernet Controller The Gigabit Ethernet Controller provides a system interface using a PCI function. The controller provides a full memory-mapped or I/O mapped interface along with a 64-bit address master support for systems using more than 4 GB of physical memory and DMA (Direct Memory Addressing) mechanisms for high performance data transfers. Its bus master capabilities enable the component to process high-level commands and perform multiple operations. This lowers processor utilization by off-loading communication tasks from the processor. Two large configurable transmit and receive FIFOs (up to 20 KB each) help prevent data underruns and overruns while waiting for bus accesses. This enables the integrated LAN controller to transmit data with minimum interframe spacing (IFS). The LAN controller can operate at multiple speeds (10/100/1000 MB/s) and in either full duplex or half duplex mode. In full duplex mode the LAN controller adheres with the IEEE 802.3x Flow Control Specification. Half duplex performance is enhanced by a proprietary collision reduction mechanism. See Section 5.4 for details. Real Time Clock (RTC) The PCH contains a Motorola MC146818B-compatible real-time clock with 256 bytes of battery-backed RAM. The real-time clock performs two key functions - keeping track of the time of day and storing system data, even when the system is powered down. The RTC operates on a 32.768-kHz crystal and a 3-V battery. 48 Datasheet Introduction The RTC also supports two lockable memory ranges. By setting bits in the configuration space, two 8-byte ranges can be locked to read and write accesses. This prevents unauthorized reading of passwords or other system security information. The RTC also supports a date alarm that allows for scheduling a wake up event up to 30 days in advance, rather than just 24 hours in advance. General Purpose I/O (GPIO) Various general purpose inputs and outputs are provided for custom system design. The number of inputs and outputs varies depending on PCH configuration. Enhanced Power Management The PCH's power management functions fully support the Advanced Configuration and Power Interface (ACPI) Specification, Revision 4.0a, and include enhanced clock control and various low-power (suspend) states (such as Suspend-to-RAM and Suspend-toDisk). A hardware-based thermal management circuit permits software-independent entrance to low-power states. Intel(R) Active Management Technology (Intel(R) AMT) Intel(R) AMT is a fundamental component of Intel(R) vProTM technology. Intel AMT is a set of advanced manageability features developed as a direct result of IT customer feedBack gained through Intel market research. With the advent of powerful tools like the Intel System Defense Utility, the extensive feature set of Intel AMT easily integrates into any network environment. See Section 1.3 for details on SKU feature availability. Manageability In addition to Intel(R) AMT, the PCH integrates several functions designed to manage the system and lower the total cost of ownership (TCO) of the system. These system management functions are designed to report errors, diagnose the system, and recover from system lockups without the aid of an external microcontroller. * TCO Timer. The PCH's integrated programmable TCO timer is used to detect system locks. The first expiration of the timer generates an SMI# that the system can use to recover from a software lock. The second expiration of the timer causes a system reset to recover from a hardware lock. * Processor Present Indicator. The PCH looks for the processor to fetch the first instruction after reset. If the processor does not fetch the first instruction, the PCH will reboot the system. * ECC Error Reporting. When detecting an ECC error, the host controller has the ability to send one of several messages to the PCH. The host controller can instruct the PCH to generate either an SMI#, NMI, SERR#, or TCO interrupt. * Function Disable. The PCH provides the ability to disable the following integrated functions: LAN, USB, LPC, Intel HD Audio, SATA, PCI Express* or SMBus. Once disabled, these functions no longer decode I/O, memory, or PCI configuration space. Also, no interrupts or power management events are generated from the disabled functions. * Intruder Detect. The PCH provides an input signal (INTRUDER#) that can be used to inform the system in the event of the case being opened. The PCH can be programmed to generate an SMI# or TCO interrupt due to an active INTRUDER# signal. Datasheet 49 Introduction System Management Bus (SMBus 2.0) The PCH contains an SMBus Host interface that allows the processor to communicate with SMBus slaves. This interface is compatible with most I2C devices. Special I2C commands are implemented. The PCH SMBus host controller provides a mechanism for the processor to initiate communications with SMBus peripherals (slaves). Also, the PCH supports slave functionality, including the Host Notify protocol. Hence, the host controller supports eight command protocols of the SMBus interface (see System Management Bus (SMBus) Specification, version 2.0): Quick Command, Send Byte, Receive Byte, Write Byte/Word, Read Byte/Word, Process Call, Block Read/Write, and Host Notify. The PCH SMBus also implements hardware-based Packet Error Checking for data robustness and the Address Resolution Protocol (ARP) to dynamically provide addresses to all SMBus devices. Intel(R) High Definition Audio (Intel(R) HD Audio) Controller The Intel HD Audio controller is a PCI Express* device, configured as D27:F0. The PCH Intel HD Audio controller supports up to 4 codecs, such as audio and modem codecs. The link can operate at either 3.3 V or 1.5 V. With the support of multi-channel audio stream, 32-bit sample depth, and sample rate up to 192 kHz, the Intel HD Audio controller provides audio quality that can deliver Consumer Electronics (such as home audio components, portable audio devices, Bluetooth* speakers, and so on) levels of audio experience. On the input side, the PCH adds support for an array of microphones. Intel(R) Virtualization Technology for Directed I/O (Intel(R) VT-d) The PCH provides hardware support for implementation of Intel Virtualization Technology with Directed I/O (Intel VT-d). Intel VT-d Technology consists of technology components that support the virtualization of platforms based on Intel Architecture processors. Intel VT-d Technology enables multiple operating systems and applications to run in independent partitions. A partition behaves like a virtual machine (VM) and provides isolation and protection across partitions. Each partition is allocated its own subset of host physical memory. Joint Test Action Group (JTAG) Boundary-Scan The PCH implements the industry standard JTAG interface and enables Boundary-Scan. Boundary-Scan can be used to ensure device connectivity during the board manufacturing process. The JTAG interface allows system manufacturers to improve efficiency by using industry available tools to test the PCH on an assembled board. Since JTAG is a serial interface, it eliminates the need to create probe points for every pin in an XOR chain. This eases pin breakout and trace routing and simplifies the interface between the system and a bed-of-nails tester. Note: The TRST# JTAG signal is an optional signal in the IEEE* 1149 JTAG Specification and is not implemented in the PCH. Integrated Clock Controller The PCH contains an Integrated Clock Controller (ICC) that generates various platform clocks from a 25 MHz crystal source. The ICC contains PLLs, Modulators, and Dividers for generating various clocks suited to the platform needs. The ICC supplies up to eight 50 Datasheet Introduction 100 MHz PCI Express 2.0 Specification compliant clocks, one 100 MHz PCI Express* 3.0 Specification compliant clock for BCLK/DMI, two 100 MHz PCI Express 3.0 Specification compliant clocks for PEG slots, one 100 MHz PCI Express 3.0 Specification compliant clock for ITP or a third PEG slot, two 135 MHz differential output clocks for DisplayPort on the processor, five 33 MHz PCI 2.3 Local Bus Specification compliant single-ended clocks for LPC/TPM devices and four Flex Clocks that can be configured to various frequencies that include 14.318 MHz, 33 MHz, and 24/48 MHz for use with SIO, TPM, EC, LPC, and any other legacy functions. Serial Over LAN (SOL) Function This function supports redirection of keyboard and text screens to a terminal window on a remote console. The keyboard and text redirection enables the control of the client machine through the network without the need to be physically near that machine. Text and keyboard redirection allows the remote machine to control and configure a client system. The SOL function emulates a standard PCI device and redirects the data from the serial port to the management console using the integrated LAN. Intel(R) KVM Technology Intel KVM technology provides enhanced capabilities to its predecessor - SOL. In addition to the features set provided by SOL, Intel KVM technology provides mouse and graphic redirection across the integrated LAN. Unlike SOL, Intel KVM technology does not appear as a host accessible PCI device, but is instead almost completely performed by Intel(R) AMT Firmware with minimal BIOS interaction. The Intel KVM technology feature is only available with internal graphics. IDE-R Function The IDE-R function is an IDE Redirection interface that provides client connection to management console ATA/ATAPI devices, such as hard disk drives and optical disk drives. A remote machine can setup a diagnostic software or operating system installation image and direct the client to boot an IDE-R session. The IDE-R interface is the same as the IDE interface; although, the device is not physically connected to the system and supports the ATA/ATAPI-6 specification. IDE-R does not conflict with any other type of boot and can, instead, be implemented as a boot device option. The Intel(R) AMT solution will use IDE-R when remote boot is required. The device attached through IDE-R is only visible to software during a management boot session. During normal boot session, the IDE-R controller does not appear as a PCI present device. Datasheet 51 Introduction 1.3 Intel(R) 8 Series/C220 Series Chipset Family PCH SKU Definition Table 1-2. Desktop Intel(R) 8 Series Chipset Family SKUs SKU Name Intel(R) Q87 Express Chipset Intel(R) Q85 Express Chipset Intel(R) B85 Express Chipset Intel(R) Z87 Express Chipset Intel(R) H87 Express Chipset Intel(R) H81 Express Chipset Flexible I/O Yes No No Yes Yes No PCI Express* 2.0 Ports 84 8 8 84 84 6 Total number of USB ports 14 14 125 14 14 106 4(6)7 4 4 4(6)7 4(6)7 28 10(8)9 10 8 10(8)9 10(8)9 8 6 6 10 4(6)10 411 Feature Set * USB 3.0 Capable Ports (SuperSpeed and all USB 2.0 speeds) * USB 2.0 Only Ports Total number of SATA ports 4(6) 10 4(6) * SATA Ports (6 Gb/s, 3 Gb/s, and 1.5 Gb/s) 6 412 412 6 6 213 * SATA Ports (3 Gb/s and 1.5 Gb/s only) 0 2 2 0 0 2 VGA Yes Yes Yes Yes Yes Yes Intel(R) Wireless Display (WiDi) Yes Yes Yes Yes Yes Yes Intel(R) Rapid Storage Technology AHCI Yes Yes Yes Yes Yes No RAID 0/1/5/10 Support Yes No No Yes Yes No Yes No No Yes Yes No Intel(R) Anti-Theft Technology15 Yes Yes Yes Yes Yes Yes Intel(R) Active Management Technology 9.0 Yes No No No No No Intel(R) Small Business Advantage16 Yes Yes Yes No Yes17 No Intel Rapid Start Technology18 Yes Yes Yes Yes Yes No Intel(R) Identity Protection Technology (Intel(R) IPT)19 Yes Yes Yes Yes Yes Yes Near Field Communication20 Yes Yes Yes Yes Yes Yes ACPI S1 State Support No No No No No No 1x16 1x16 1x16 1x16, 2x8, 1x8, 2x4 1x16 1x16 Gen 3 (8GT/s) Gen 3 (8GT/s) Gen 3 (8GT/s) Gen 3 (8GT/s) Gen 3 (8GT/s) Gen 2 (5GT/s) 3 3 3 3 3 2 2 (2) 2 (2) 2 (2) 2 (2) 2 (2) 2 (1) Processor and Memory Overclocking Disabled Disabled Disabled Enabled Disabled Disabled Processor Graphics Enabled Enabled Enabled Enabled Enabled Enabled (R) Intel Smart Response Technology14 21 Processor Features Controlled by PCH SKU Processor PEG Port Bifurcation Processor PEG Port Maximum Speed Allowed Processor Maximum Number of Independent Displays Supported Processor Maximum Number of Memory Channels (Maximum DIMMS per Channel) Notes: 1. Contact your local Intel Field Sales Representative for currently available PCH SKUs. 2. Table above shows feature differences between the PCH SKUs. If a feature is not listed in the table it is considered a Base feature that is included in all SKUs. 3. PCI Legacy Mode may optionally be used allowing external PCI bus support through a PCIe-to-PCI bridge. See Section 5.2.2 for more details. 4. The number of PCI Express ports available depends on the Flexible I/O configuration. See Section 2.1 and Table 1-3. 52 Datasheet Introduction 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. Table 1-3. USB 2.0 ports 6 and 7 are disabled on 12 port SKUs. USB 2.0 ports 6,7,12 and 13 are disabled on 10 port SKUs. 6 USB 3.0 ports requires High Speed I/O ports 5 and 6 to be configured as USB 3.0. See Section 2.1 and Table 1-3. Only USB 3.0 ports 1 and 2 are enabled. When Flexible I/O ports are configured as USB 3.0, the total number of USB 2.0 only ports reduces in direct proportion. 6 SATA ports requires High Speed I/O ports 13 and 14 to be configured as SATA. See Section 2.1 and Table 1-3. SATA ports 2 and 3 are disabled on 4 port SKUs. SATA 6 Gb/s support on ports 0,1,2 and 3. SATA ports 0,1,2 and 3 also support 3 Gb/s and 1.5 Gb/s. SATA 6 Gb/s support on ports 0 and 1 only. SATA ports 0 and 1 also support 3 Gb/s and 1.5 Gb/s. Intel(R) Smart Response Technology requires an Intel(R) CoreTM processor. Intel(R) Anti-Theft Technology requires an Intel(R) CoreTM processor. Intel(R) Small Business Advantage requires an Intel(R) CoreTM processor. Intel(R) Small Business Advantage with the Intel(R) H87 Express Chipset requires 5Mb firmware. Intel(R) Rapid Start Technology requires an Intel(R) CoreTM processor. Intel(R) Identity Protection Technology requires an Intel(R) CoreTM processor. Near Field Communication is only supported in All-in-One system designs. Refer to the processor datasheet for additional details on processor features. Intel(R) 8 Series/C220 Series Chipset Family PCH SKUs Flexible I/O Map High Speed I/O Ports SKU Port 1 Port 2 Port 3 Port 4 Port 5 Port 6 Port 7 Port 8 Port 9 Port 10 Port 11 Port 12 Port 13 Port 14 Port 15 Port 16 Port 17 Port 18 Q87 USB USB 3.0 3.0 USB USB USB USB Port 3 Port 4 PCIe* PCIe* PCIe* PCIe* PCIe* PCIe* 3.0 3.0 3.0 3.0 Port 1 Port 2 Port 5 Port 6 PCIe* PCIe* Port 3 Port 4 Port 5 Port 6 Port 7 Port 8 Port 1 Port 2 Q85 USB USB USB USB PCIe* PCIe* PCIe* PCIe* PCIe* PCIe* PCIe* PCIe* SATA SATA SATA SATA SATA SATA 3.0 3.0 3.0 3.0 3Gb/s 3Gb/s 6Gb/s 6Gb/s 6Gb/s 6Gb/s Port 1 Port 2 Port 5 Port 6 Port 1 Port 2 Port 3 Port 4 Port 5 Port 6 Port 7 Port 8 Port 4 Port 5 Port 0 Port 1 Port 2 Port 3 B85 USB USB USB USB PCIe* PCIe* PCIe* PCIe* PCIe* PCIe* PCIe* PCIe* SATA SATA SATA SATA SATA SATA 3.0 3.0 3.0 3.0 3Gb/s 3Gb/s 6Gb/s 6Gb/s 6Gb/s 6Gb/s Port 1 Port 2 Port 5 Port 6 Port 1 Port 2 Port 3 Port 4 Port 5 Port 6 Port 7 Port 8 Port 4 Port 5 Port 0 Port 1 Port 2 Port 3 Z87 USB USB 3.0 3.0 USB USB USB USB Port 3 Port 4 PCIe* PCIe* PCIe* PCIe* PCIe* PCIe* 3.0 3.0 3.0 3.0 Port 3 Port 4 Port 5 Port 6 Port 7 Port 8 Port 1 Port 2 Port 5 Port 6 PCIe* PCIe* Port 1 Port 2 SATA SATA 6Gb/s 6Gb/s SATA SATA SATA SATA Port 4 Port 5 6Gb/s 6Gb/s 6Gb/s 6Gb/s PCIe* PCIe* Port 0 Port 1 Port 2 Port 3 Port 1 Port 2 H87 USB USB 3.0 3.0 USB USB USB USB Port 3 Port 4 PCIe* PCIe* PCIe* PCIe* PCIe* PCIe* 3.0 3.0 3.0 3.0 Port 3 Port 4 Port 5 Port 6 Port 7 Port 8 Port 1 Port 2 Port 5 Port 6 PCIe* PCIe* Port 1 Port 2 SATA SATA 6Gb/s 6Gb/s SATA SATA SATA SATA Port 4 Port 5 6Gb/s 6Gb/s 6Gb/s 6Gb/s PCIe* PCIe* Port 0 Port 1 Port 2 Port 3 Port 1 Port 2 H81 USB USB 3.0 3.0 Port 1 Port 2 SATA SATA SATA SATA 3Gb/s 3Gb/s 6Gb/s 6Gb/s Port 4 Port 5 Port 0 Port 1 NA NA PCIe* PCIe* PCIe* PCIe* PCIe* PCIe* Port 1 Port 2 Port 3 Port 4 Port 5 Port 6 NA NA SATA SATA 6Gb/s 6Gb/s SATA SATA SATA SATA Port 4 Port 5 6Gb/s 6Gb/s 6Gb/s 6Gb/s PCIe* PCIe* Port 0 Port 1 Port 2 Port 3 Port 1 Port 2 NA Notes: 1. Ports listed with NA are not available and are disabled. Datasheet 53 NA Introduction Table 1-4. Mobile Intel(R) 8 Series Chipset Family SKUs SKU Name Feature Set Flexible I/O PCI Express* 2.0 Ports Mobile Intel(R) QM87 Express Chipset Mobile Intel(R) HM87 Express Chipset Mobile Intel(R) HM86 Express Chipset Yes Yes Yes4 8 Total number of USB ports *USB 3.0 Capable Ports (SuperSpeed and all USB 2.0 speeds) *USB 2.0 Only Ports Total number of SATA ports 5 8 14 14 14 4(6) 2(4)7 10(8)8 10(8)8 12(10)8 9 11 2(4) *SATA Ports (3 Gb/s and 1.5 Gb/s only) VGA Intel(R) Wireless Display (WiDi) 85 4(6)6 4(6) *SATA Ports (6 Gb/s, 3 Gb/s, and 1.5 Gb/s) 5 9 410 11 212 4(6) 2(4) 2 2 2 Yes Yes Yes Yes Yes Yes AHCI Yes Yes Yes RAID 0/1/5/10 Support Yes Yes No Intel(R) Smart Response Technology13 Yes Yes No Intel(R) Anti-Theft Technology14 Yes Yes Yes Intel(R) Active Management Technology 9.0 Yes No No Intel(R) Small Business Advantage15 Yes Yes16 No Intel Rapid Start Technology17 Yes Yes Yes Intel(R) Identity Protection Technology (Intel(R) IPT)18 Yes Yes Yes Near Field Communication Yes Yes Yes ACPI S1 State Support No No No Intel(R) Rapid Storage Technology Processor Features Controlled by PCH SKU19 Processor PEG Port Bifurcation Processor PEG Port Maximum Speed Allowed Processor Maximum Number of Independent Displays Supported 1x16 1x16 1x16 Gen 3 (8GT/s) Gen 3 (8GT/s) Gen 2 (5GT/s) 3 3 2 2 (2) 2 (2) 2 (1) Processor and Memory Overclocking19 Disabled Disabled Disabled Processor Graphics Enabled Enabled Enabled Processor Maximum Number of Memory Channels (Maximum DIMMS per Channel) Notes: 1. Contact your local Intel Field Sales Representative for currently available PCH SKUs. 2. Table above shows feature difference between the PCH SKUs. If a feature is not listed in the table, it is considered a Base feature that is included in all SKUs. 3. PCI Legacy Mode may optionally be used allowing external PCI bus support through a PCIe-to-PCI bridge. See Section 5.2.2 for more details. 4. Flexible I/O is only available on High Speed I/O ports 5 and 6 which are shared between USB 3.0 and PCI Express. High Speed I/O ports 13 and 14 are fixed as SATA Gen 2 ports. See Section 2.1 and Table 1-5. 5. The number of PCI Express ports available depends on the Flexible I/O configuration. See Section 2.1 and Table 1-5. 6. 6 USB 3.0 ports requires High Speed I/O ports 5 and 6 to be configured as USB 3.0. See Section 2.1 and Table 1-5. 7. USB 3.0 ports 5 and 6 are disabled on the Intel(R) HM86 Express Chipset. 8. When Flexible I/O ports are configured as USB 3.0, the total number of USB 2.0 only ports reduces in direct proportion. 9. 6 SATA ports requires High Speed I/O ports 13 and 14 to be configured as SATA. See Section 2.1 and Table 1-5. 10. SATA ports 1 and 3 are disabled on 4 port SKUs. 11. SATA 6 Gb/s support on ports 0,1,4 and 5. SATA ports 0,1,4 and 5 also support 3 Gb/s and 1.5 Gb/s. In order to support 4 SATA 6 Gb/s ports, High Speed I/O ports 13 and 14 must be configured as SATA. See Section 2.1 and Table 1-5. 12. SATA 6 Gb/s support on port 4 and port 5. SATA ports 4 and 5 also support 3 Gb/s and 1.5 Gb/s. 13. Intel(R) Smart Response Technology requires an Intel(R) CoreTM processor. 54 Datasheet Introduction 14. 15. 16. 17. 18. 19. Table 1-5. Intel(R) Anti-Theft Technology requires an Intel(R) CoreTM processor. Intel(R) Small Business Advantage requires an Intel(R) CoreTM processor. Intel(R) Small Business Advantage with the Intel(R) HM87 Express Chipset requires 5Mb firmware. Intel(R) Rapid Start Technology requires an Intel(R) CoreTM processor. Intel(R) Identity Protection Technology requires an Intel(R) CoreTM processor. Refer to the processor datasheet for additional details on processor features. Intel(R) 8 Series/C220 Series Chipset Family PCH SKUs Flexible I/O Map High Speed I/O Ports SKU Port 1 Port 2 Port 3 Port 4 Port 5 Port 6 Port 7 Port 8 Port 9 Port 10 Port 11 Port 12 Port 13 Port 14 Port 15 Port 16 Port 17 Port 18 USB USB 3.0 3.0 USB USB USB USB Port 3 Port 4 PCIe* PCIe* PCIe* PCIe* PCIe* PCIe* 3.0 3.0 3.0 3.0 QM87 Port 3 Port 4 Port 5 Port 6 Port 7 Port 8 Port 1 Port 2 Port 5 Port 6 PCIe* PCIe* Port 1 Port 2 SATA SATA 6Gb/s 6Gb/s SATA SATA SATA SATA Port 4 Port 5 6Gb/s 6Gb/s 3Gb/s 3Gb/s PCIe* PCIe* Port 0 Port 1 Port 2 Port 3 Port 1 Port 2 USB USB 3.0 3.0 USB USB USB USB PCIe* PCIe* PCIe* PCIe* PCIe* PCIe* HM87 3.0 3.0 3.0 3.0 Port 3 Port 4 Port 3 Port 4 Port 5 Port 6 Port 7 Port 8 Port 1 Port 2 Port 5 Port 6 PCIe* PCIe* Port 1 Port 2 SATA SATA 6Gb/s 6Gb/s SATA SATA SATA SATA Port 4 Port 5 6Gb/s 6Gb/s 3Gb/s 3Gb/s PCIe* PCIe* Port 0 Port 1 Port 2 Port 3 Port 1 Port 2 USB USB 3.0 3.0 HM86 Port 1 Port 2 NA NA USB USB 3.0 3.0 SATA SATA SATA Port 3 Port 4 PCIe* PCIe* PCIe* PCIe* PCIe* PCIe* 6Gb/s 6Gb/s 3Gb/s Port 3 Port 4 Port 5 Port 6 Port 7 Port 8 Port 4 Port 5 Port 0 PCIe* PCIe* Port 1 Port 2 NA SATA 3Gb/s Port 2 Notes: 1. Ports listed with NA are not available and are disabled. Table 1-6. Server / Workstation Intel(R) C220 Series Chipset Family SKUs (Sheet 1 of 2) SKU Name Feature Set Flexible I/O PCI Express* 2.0 Ports Total number of USB ports (R) Intel C222 Chipset Intel(R) C224 Chipset Intel(R) C226 Chipset No No Yes 8 8 84 10 5 12 6 14 * USB 3.0 Capable Ports (SuperSpeed and all USB 2.0 speeds) 27 48 4(6)9 * USB 2.0 Only Ports 8 8 10(8)10 Total number of SATA ports 6 6 4(6)11 12 13 4(6)11 * SATA Ports (6 Gb/s, 3 Gb/s, and 1.5 Gb/s) * SATA Ports (3 Gb/s and 1.5 Gb/s only) VGA Intel(R) Wireless Display (WiDi) 2 4 4 2 0 No No Yes No No Yes AHCI Yes Yes Yes RAID 0/1/5/10 Support Yes Yes Yes Intel(R) Smart Response Technology14 No No Yes Intel(R) Anti-Theft Technology15 No No No Intel(R) Active Management Technology 9.0 No No Yes Intel(R) Small Business Advantage No No No Intel Rapid Start Technology No No No Intel(R) Identity Protection Technology (Intel(R) IPT)16 No No Yes Near Field Communication No No No ACPI S1 State Support No No No Intel(R) Rapid Storage Technology Datasheet 55 NA Introduction Table 1-6. Server / Workstation Intel(R) C220 Series Chipset Family SKUs (Sheet 2 of 2) SKU Name (R) Feature Set Intel C222 Chipset Intel(R) C224 Chipset Intel(R) C226 Chipset 1x16, 2x8, 1x8, 2x4 1x16, 2x8, 1x8, 2x4 1x16, 2x8, 1x8, 2x4 Gen 3 (8GT/s) Gen 3 (8GT/s) Gen 3 (8GT/s) Processor Features Controlled by PCH SKU17 Processor PEG Port Bifurcation Processor PEG Port Maximum Speed Allowed Processor Maximum Number of Independent Displays Supported 3 3 3 2 (2) 2 (2) 2 (2) Processor and Memory Overclocking Disabled Disabled Disabled Processor Graphics Disabled Disabled Enabled Processor Maximum Number of Memory Channels (Maximum DIMMS per Channel) Notes: 1. Contact your local Intel Field Sales Representative for currently available PCH SKUs. 2. Table above shows feature differences between the PCH SKUs. If a feature is not listed in the table, it is considered a Base feature that is included in all SKUs 3. PCI Legacy Mode may optionally be used allowing external PCI bus support through a PCIe-to-PCI bridge. See Section 5.2.2 for more details. 4. The number of PCI Express ports available depends on the Flexible I/O configuration. See Section 2.1 and Table 1-7. 5. USB 2.0 ports 6,7,12 and 13 are disabled on 10 port SKUs. 6. USB 2.0 ports 6 and 7 are disabled on 12 port SKUs. 7. Only USB 3.0 ports 1 and 2 are enabled. 8. Only USB 3.0 ports 1,2,5 and 6 are enabled. 9. 6 USB 3.0 ports require High Speed I/O ports 5 and 6 to be configured as USB 3.0. See Section 2.1 and Table 1-7. 10. When Flexible I/O ports are configured as USB 3.0, the total number of USB 2.0 only ports reduces in direct proportion. 11. 6 SATA ports require High Speed I/O ports 13 and 14 to be configured as SATA. See Section 2.1 and Table 1-7. 12. SATA 6 Gb/s support on ports 0 and 1 only. SATA ports 0 and 1 also support 3 Gb/s and 1.5 Gb/s. 13. SATA 6 Gb/s support on ports 0,1,2 and 3. SATA ports 0,1,2 and 3 also support 3 Gb/s and 1.5 Gb/s. 14. Intel(R) Smart Response Technology requires an Intel(R) CoreTM processor. 15. Intel(R) Anti-Theft Technology requires an Intel(R) CoreTM processor. 16. Intel(R) Identity Protection Technology requires an Intel(R) Xeon(R) processor. 17. Refer to the processor datasheet for additional details on processor features. Table 1-7. Server / Workstation Intel(R) C220 Series Chipset Family SKUs Flexible I/O Map High Speed I/O Ports SKU Port 1 Port 2 Port 3 Port 4 NA NA Port 5 Port 6 Port 7 Port 8 Port 9 Port 10 Port 11 Port 12 Port 13 Port 14 Port 15 Port 16 Port 17 Port 18 C222 USB USB 3.0 3.0 Port 1 Port 2 PCIe* PCIe* PCIe* PCIe* PCIe* PCIe* PCIe* PCIe* SATA SATA SATA SATA SATA SATA 3Gb/s 6Gb/s 6Gb/s 3Gb/s 3Gb/s Port 1 Port 2 Port 3 Port 4 Port 5 Port 6 Port 7 Port 8 3Gb/s Port 4 Port 5 Port 0 Port 1 Port 2 Port 3 C224 USB USB USB USB PCIe* PCIe* PCIe* PCIe* PCIe* PCIe* PCIe* PCIe* SATA SATA SATA SATA SATA SATA 3.0 3.0 3.0 3.0 3Gb/s 3Gb/s 6Gb/s 6Gb/s 6Gb/s 6Gb/s Port 1 Port 2 Port 5 Port 6 Port 1 Port 2 Port 3 Port 4 Port 5 Port 6 Port 7 Port 8 Port 4 Port 5 Port 0 Port 1 Port 2 Port 3 USB USB SATA SATA 3.0 3.0 6Gb/s 6Gb/s SATA SATA SATA SATA USB USB USB USB 3.0 3.0 3.0 3.0 Port 3 Port 4 PCIe* PCIe* PCIe* PCIe* PCIe* PCIe* Port 4 Port 5 6Gb/s 6Gb/s 6Gb/s 6Gb/s C226 Port 3 Port 4 Port 5 Port 6 Port 7 Port 8 Port 1 Port 2 Port 5 Port 6 PCIe* PCIe* PCIe* PCIe* Port 0 Port 1 Port 2 Port 3 Port 1 Port 2 Port 1 Port 2 Notes: 1. Ports listed with NA are not available and are disabled. 56 Datasheet Introduction 1.4 Device and Revision ID Table The Revision ID (RID) register is an 8-bit register located at offset 08h in the PCI header of every PCI/PCIe function. The RID register is used by software to identify a particular component stepping when a driver change or patch unique to that stepping is needed. Table 1-8. PCH Device and Revision ID Table (Sheet 1 of 3) Device Function Description Dev ID D31:F2 SATA1 8C00h 04h Desktop: Non-AHCI and Non-RAID Mode. 8C01h 04h Mobile: Non-AHCI and Non-RAID Mode. D31:F5 D28:F0 D28:F1 D28:F2 D28:F3 Datasheet SATA PCI Express* Port 1 C1 SRID Comments 8C02h 04h Desktop: AHCI Mode. 8C03h 04h Mobile: AHCI Mode. 8C04h 04h Desktop: RAID Capable3 if AIE (D31:F2 Offset 9Ch bit 7) = 1. 2822h 04h Desktop: RAID Capable3 with or without Intel(R) Smart Response Technology, if AIE (D31:F2 Offset 9Ch bit 7) = 0 AND AIES (D31:F2 Offset 9Ch bit 6) = 0. 8C05h 04h Mobile: RAID Capable3 if AIE (D31:F2 Offset 9Ch bit 7) = 1. 282Ah 04h Mobile: RAID Capable3 with or without Intel(R) Smart Response Technology, if AIE (D31:F2 Offset 9Ch bit 7) = 0. 8C06h 04h Desktop: RAID Capable3 and Intel(R) Smart Response Technology, if AIE (D31:F2 Offset 9Ch bit 7) = 1. 2826h 04h Server/Workstation: RAID Capable3 and Intel(R) Smart Response Technology, if AIE (D31:F2 Offset 9Ch bit 7) = 0 AND AIES (D31:F2 Offset 9Ch bit 6) = 1. 8C07h 04h Mobile: RAID Capable3 and Intel(R) Smart Response Technology, if AIE (D31:F2 Offset 9Ch bit 7) = 1. 8C0Eh 04h Desktop: RAID 1 Only. 8C0Fh 04h Mobile: RAID 1 Only. 8C08h 04h Desktop: Non-AHCI and Non-RAID Mode (Ports 4 and 5) 8C09h 04h Mobile: Non-AHCI and Non-RAID Mode (Ports 4 and 5) 8C10h 04h Desktop and Mobile (When D28:F0:ECh:bit 1= 0) 244Eh 04h Desktop (When D28:F0:ECh:bit 1 = 1) 2448h 04h Mobile (When D28:F0:ECh:bit 1 = 1) PCI Express Port 2 8C12h 04h Desktop and Mobile (When D28:F1:ECh:bit 1 = 0) 244Eh 04h Desktop (When D28:F1:ECh:bit 1 = 1) 2448h 04h Mobile (When D28:F1:ECh:bit 1 = 1) PCI Express Port 3 8C14h 04h Desktop and Mobile (When D28:F2:ECh:bit 1 = 0) PCI Express Port 4 244Eh 04h Desktop (When D28:F2:ECh:bit 1 = 1) 2448h 04h Mobile (When D28:F2:ECh:bit 1 = 1) 8C16h 04h Desktop and Mobile (When D28:F3:ECh:bit 1 = 0) 244Eh 04h Desktop (When D28:F3:ECh:bit 1 = 1) 2448h 04h Mobile (When D28:F3:ECh:bit 1 = 1) 57 Introduction Table 1-8. PCH Device and Revision ID Table (Sheet 2 of 3) Description D28:F4 PCI Express Port 5 8C18h 04h Desktop and Mobile (When D28:F4:ECh:bit 1 = 0) 244Eh 04h Desktop (When D28:F4:ECh:bit 1 = 1) 2448h 04h Mobile (When D28:F4:ECh:bit 1 = 1) PCI Express Port 6 8C1Ah 04h Desktop and Mobile (When D28:F5:ECh:bit 1 = 0) 244Eh 04h Desktop (When D28:F5:ECh:bit 1 = 1) 2448h 04h Mobile (When D28:F5:ECh:bit 1 = 1) D28:F5 D28:F6 Dev ID Comments PCI Express Port 7 8C1Ch 04h Desktop and Mobile (When D28:F6:ECh:bit 1 = 0) 244Eh 04h Desktop (When D28:F6:ECh:bit 1 = 1) 2448h 04h Mobile (When D28:F6:ECh:bit 1 = 1) PCI Express Port 8 8C1Eh 04h Desktop and Mobile (When D28:F7:ECh:bit 1 = 0) 244Eh 04h Desktop (When D28:F7:ECh:bit 1 = 1) 2448h 04h Mobile (When D28:F7:ECh:bit 1 = 1) D27:F0 (R) Intel High Definition Audio 8C20h 04h Desktop and Mobile - All SKUs. D31:F3 SMBus 8C22h 04h Desktop and Mobile - All SKUs. D28:F7 58 C1 SRID Device Function D31:F6 Thermal 8C24h 04h Desktop and Mobile - All SKUs. D29:F0 USB EHCI #1 8C26h 04h Desktop and Mobile - All SKUs. D26:F0 USB EHCI #2 8C2Dh 04h Desktop and Mobile - All SKUs. D20:F0 USB xHCI 8C31h 04h Desktop and Mobile - All SKUs. D25:F0 LAN 8C33h 04h Desktop and Mobile - All SKUs. D22:F0 Intel(R) ME Interface #1 8C3Ah 04h Desktop and Mobile - All SKUs. D22:F1 Intel ME Interface #2 8C3Bh 04h Desktop and Mobile - All SKUs. D22:F2 IDE-R 8C3Ch 04h Desktop and Mobile - All SKUs. D22:F3 KT 8C3Dh 04h Desktop and Mobile - All SKUs. Datasheet Introduction Table 1-8. PCH Device and Revision ID Table (Sheet 3 of 3) C1 SRID Device Function Description Dev ID D31:F0 LPC 8C41h 04h LPC Controller (Mobile Full Featured Engineering Sample). 8C42h 04h LPC Controller (Desktop Full Featured Engineering Sample). 8C44h 04h LPC Controller (Z87 SKU). 8C46h 04h LPC Controller (Z85 SKU). Comments 8C49h 04h LPC Controller (HM86 SKU). 8C4Ah 04h LPC Controller (H87 SKU). 8C4Bh 04h LPC Controller (HM87 SKU). 8C4Ch 04h LPC Controller (Q85 SKU). 8C4Eh 04h LPC Controller (Q87 SKU). 8C4Fh 04h LPC Controller (QM87 SKU). 8C50h 04h LPC Controller (B85 SKU). 8C52h 04h LPC Controller (C222 SKU). 8C54h 04h LPC Controller (C224 SKU). 8C56h 04h LPC Controller (C226 SKU). 8C5Ch 04h LPC Controller (H81 SKU). Notes: 1. PCH contains two SATA controllers. The SATA Device ID is dependent upon which SATA mode is selected by BIOS and what RAID capabilities exist in the SKU. 2. The SATA RAID Controller Device ID is dependent upon the AIE bit setting (bit 7 of D31:F2:Offset 9Ch). 3. SATA Controller 2 (D31:F5) is only visible when D31:F2 CC.SCC =01h. 4. LAN Device ID is loaded from EEPROM. If EEPROM contains either 0000h or FFFFh in the Device ID location, then 8C33h is used. Refer to the appropriate Intel(R) GbE physical layer Transceiver (PHY) datasheet for LAN Device IDs. 5. For a given stepping, not all SKUs may be available. 6. This table shows the default PCI Express Function Number-to-Root Port mapping. Function numbers for a given root port are assignable through the "Root Port Function Number and Hide for PCI Express Root Ports" register (RCBA+0404h). Datasheet 59 Signal Description 2 Signal Description This chapter provides a detailed description of each signal. The signals are arranged in functional groups according to their associated interface. The "#" symbol at the end of the signal name indicates that the active, or asserted state occurs when the signal is at a low voltage level. When "#" is not present, the signal is asserted when voltage level is high. The following notations are used to describe the signal type: I Input Pin. O Output Pin. OD O Open Drain Output Pin. I/OD Bi-directional Input/Open Drain Output Pin. I/O Bi-directional Input/Output Pin. CMOS CMOS buffers. 1.5 V tolerant. COD CMOS Open Drain buffers. 3.3 V tolerant. HVCMOS High Voltage CMOS buffers. 3.3 V tolerant. A Analog reference or output. The "Type" for each signal is indicative of the functional operating mode of the signal. Unless otherwise noted in Section 3.2 or Section 3.3, a signal is considered to be in the functional operating mode after RTCRST# de-asserts for signals in the RTC well, after RSMRST# de-asserts for signals in the suspend well, after PWROK asserts for signals in the core well, after DPWROK asserts for signals in the DeepSx well, after APWROK asserts for signals in the Active Sleep well. Note: 60 Core well includes 1.05 V, 1.5 V and 3.3 V rails powering PCH logic and these rails may be shut off in S3, S4, S5, and G3 states. Datasheet Signal Description Figure 2-1. PCH Interface Signals Block Diagram (not all signals are on all SKUs) GPIO50 GPIO52 GPIO54 GPIO51 GPIO53 GPIO55 CLKIN_33MHZLOOPBACK PMSYNCH RCIN# THRMPTRIP# PROCPWRGD SPI_IO1 SPI_IO2 SPI_MISO SPI_MOSI SPI_CS0#; SPI_CS1#;SPI_CS2# SPI_CLK Controller Link Processor Interface SPI LAD[3:0] LFRAME# LDRQ0#; LDRQ1#/GPIO23 LPC / FWH Interface CLKOUT_DP_[P,N] CLKOUT_DMI_[P,N] XTAL25_OUT CLKOUT_PEG_A_[P,N];CLKOUT_PEG_B_[P,N] CLKOUT_PCIE[7:0]_[P,N] CLKOUT_ITPXDP_[P,N] CLKOUT_33MHz[4:0] CLKOUTFLEX0/GPIO64;CLKOUTFLEX1/GPIO65 CLKOUTFLEX2/GPIO66;CLKOUTFLEX3/GPIO67 Clock Outputs CLKIN_DMI_[P,N] CLKIN_SATA_[P,N] CLKIN_DOT96[P,N] XTAL25_IN;REF14CLKIN PCIECLKRQ0#/GPIO73;PCIECLKRQ1#/GPIO18 PCIECLKRQ2#/GPIO20/SMI#;PCIECLKRQ3#/GPIO25 PCIECLKRQ4#/GPIO26;PCIECLKRQ5#/GPIO44 PCIECLKRQ6#/GPIO45;PCIECLKRQ7#/GPIO46 PEG_A_CLKRQ#/GPIO47;PEG_B_CLKRQ#/GPIO56 SERIRQ PIRQ[D:A]# PIRQ[H:E]#/GPIO[5:2] USB RTCX1 RTCX2 RTC GPIO[72,57,32,28,27,15,8] PWM[3:0] TACH7/GPIO71;TACH6/GPIO70; TACH5/GPIO69;TACH4/GPIO68 TACH3/GPIO7; TACH2/GPIO6; TACH1/GPIO1;TACH0/GPIO17 SST PECI JTAGTCK JTAGTMS JTAGTDI JTAGTDO Misc. Signals General Purpose I/O Fan Speed Control JTAG CL_CLK ; CL_DATA CL_RST# PET[p,n][8:1] PER[p,n][8:1] PCIE_RCOMP PCIE_IREF Serial ATA Interface SATA_TX[P,N][5:0] SATA_RX[P,N][5:0] SATA_RCOMP SATA_IREF SATALED# SATA0GP/GPIO21 SATA1GP/GPIO19 SATA2GP/GPIO36 SATA3GP/GPIO37 SATA4GP/GPIO16 SATA5GP/GPIO49 SCLOCK/GPIO22, SLOAD/GPIO38 SDATAOUT0/GPIO39, SDATAOUT1/GPIO48 Clock Inputs Interrupt Interface FDI_RXP[1:0] FDI_RXN[1:0] FDI_CSYNC FDI_INT FDI_RCOMP FDI_IREF PCI Express* Interface Power Mgnt. USB[13:0][P,N] OC0#/GPIO59; OC1#/GPIO40 OC2#/GPIO41; OC3#/GPIO42 OC4#/GPIO43; OC5#/GPIO9 OC6#/GPIO10; OC7#/GPIO14 USBRBIAS, USBRBIAS# USB3[T,R][p,n][6:1] INTVRMEN, DSWVRMEN SPKR SRTCRST#; RTCRST# GPIO35/NMI# GPIO24 PME# Datasheet MISC. Signals Intel(R) Flexible Display Interface Intel(R) High Definition Audio SUSWARN#/SUSPWRDNACK/GPIO30 DPWROK SYS_RESET# RSMRST# SLP_S3# SLP_S4# SLP_S5#/GPIO63 SLP_A# CLKRUN#/GPIO32 PWROK AWROK PWRBTN# RI# WAKE# SUS_STAT#/GPIO61 SUSCLK/GPIO62 BATLOW#/GPIO72 PLTRST# BMBUSY#/GPIO0 GPIO34 ACPRESENT/GPIO31 DRAMPWROK LAN_PHY_PWR_CTRL/GPIO12 SLP_WLAN#/GPIO29 SUSACK# SLP_SUS# PLTRST# HDA_RST# HDA_SYNC HDA_BCLK HDA_SDO HDA_SDIN[3:0] HDA_DOCK_EN#/HDA_DOCK_RST# Direct Media Interface DMI_TX[P,N][3:0] DMI_RX[P,N][3:0] DMI_RCOMP DMI_IREF SMBus Interface SMBDATA; SMBCLK SMBALERT#/GPIO11 System Mgnt. Analog Display Digital Display Sideband Signals INTRUDER#; SML[1:0]DATA;SML[1:0]CLK SML0ALERT#/GPIO60 SML1ALERT#/TEMP_ALERT#/GPIO74 VGA_RED;VGA_GREEN;VGA_BLUE DAC_IREF VGA_HSYNC;VGA_VSYNC VGA_DDC_CLK;VGA_DDC_DATA VGA_IRTN DDP[B:D]_AUX[P,N] DDP[B:D]_HPD DDP[B:D]_CTRLCLK DDP[B:D]_CTRLDATA eDP_BKLTEN eDP_BKLTCTL eDP_VDDEN 61 Signal Description 2.1 Flexible I/O The Intel(R) 8 Series/C220 Series Chipset Family PCH implements Flexible I/O, a technology to allow some high speed signals to be configured as PCIe*, USB 3.0, or SATA signals. There are a total of 18 High Speed I/O Ports in the PCH and, through soft straps, four of these ports can have their functionality selected to meet the I/O needs of the platform. Table 2-1 illustrates high speed I/O ports mapping to PCIe, USB 3.0 and SATA signals. Table 2-1. I/O Flexibility Signal Mapping High Speed I/ O Ports GbE Map PCIe Signals USB 3.0 Signals SATA Signals 1 -- -- USB3Tp/n1 USB3Rp/n1 -- 2 -- -- USB3Tp/n2 USB3Rp/n2 -- 3 -- -- USB3Tp/n5 USB3Rp/n5 -- 4 -- -- USB3Tp/n6 USB3Rp/n6 -- 5 000 (soft strap) PETp/n1 PERp/n1 USB3Tp/n3 USB3Rp/n3 -- 6 001 (soft strap) PETp/n2 PERp/n2 USB3Tp/n4 USB3Rp/n4 -- 7 010 (soft strap) PETp/n3 PERp/n3 -- -- 8 011 (soft strap) PETp/n4 PERp/n4 -- -- 9 100 (soft strap) PETp/n5 PERp/n5 -- -- 10 101 (soft strap) PETp/n6 PERp/n6 -- -- 11 110 (soft strap) PETp/n7 PERp/n7 -- -- 12 111 (soft strap) PETp/n8 PERp/n8 -- -- 13 -- PETp/n1 PERp/n1 -- SATA_TXp/n4 SATA_RXp/n4 14 -- PETp/n2 PERp/n2 -- SATA_TXp/n5 SATA_RXp/n5 15 -- -- -- SATA_TXp/n0 SATA_RXp/n0 16 -- -- -- SATA_TXp/n1 SATA_RXp/n1 17 -- -- -- SATA_TXp/n2 SATA_RXp/n2 18 -- -- -- SATA_TXp/n3 SATA_RXp/n3 Notes: 1. High speed I/O ports 5 and 6 can be configured as either PCIe port 1 and 2 or USB 3.0 port 3 and 4. 2. High speed I/O ports 13 and 14 can be configured as either PCIe port 1 and 2 or SATA port 4 and 5. 3. Maximum of 8 PCIe* ports, 6 USB 3.0 Ports or 6 SATA ports possible. GbE uses the physical interface of PCIe ports so having 8 PCIe ports + 1 GbE simultaneously does not mean a total of 9 PCIe ports. 8 PCIe ports + 1 GbE simultaneously is supported (depending on SKU configuration). 4. Refer to Chapter 5.22 for more details. 62 Datasheet Signal Description 2.2 USB Interface Note: The USB 2.0 signals in the PCH integrate pull-down resistors and provide an output driver impedance of 45 that requires no external series resistor. No external pull-up/ pull-down resistors should be added to the USB 2.0 signals. USB ports not needed can be left floating as No Connect. Note: The voltage divider formed by the device pull-up and the host pull-down will ensure the data wire park at a safe voltage level, which is below the VBUS value. This ensures that the host/hub will not see 5 V at the wire when inter-operating with devices that have VBUS at 5 V. Note: All USB 2.0 register addresses throughout the datasheet correspond to the external pin names. Refer to Table 2-2 to know exactly how the USB pins are mapped to the different internal ports within the xHCI and EHCI controllers. Table 2-2. USB Interface Signals (Sheet 1 of 3) xHCI Port EHCI Port Type USB2p0 USB2n0 0 0 I/O USB 2.0 Port 0 Transmit/Receive Differential Pair 0: This USB 2.0 signal pair can be routed to xHCI or EHCI Controller 1 through software and should map to a USB connector with one of the overcurrent OC Pins 0-3. USB2p1 USB2n1 1 1 I/O USB 2.0 Port 1 Transmit/Receive Differential Pair 1: This USB 2.0 signal pair can be routed to xHCI or EHCI Controller 1 through software and should map to a USB connector with one of the overcurrent OC Pins 0-3. USB2p2 USB2n2 2 2 I/O USB 2.0 Port 2 Transmit/Receive Differential Pair 2: This USB 2.0 signal pair can be routed to xHCI or EHCI Controller 1 through software and should map to a USB connector with one of the overcurrent OC Pins 0-3. USB2p3 USB2n3 3 3 I/O USB 2.0 Port 3 Transmit/Receive Differential Pair 3: This USB 2.0 signal pair can be routed to xHCI or EHCI Controller 1 through software and should map to a USB connector with one of the overcurrent OC Pins 0-3. USB2p4 USB2n4 8 4 I/O USB 2.0 Port 4 Transmit/Receive Differential Pair 4: This USB 2.0 signal pair can be routed to xHCI or EHCI Controller 1 through software and should map to a USB connector with one of the overcurrent OC Pins 0-3. USB2p5 USB2n5 9 5 I/O USB 2.0 Port 5 Transmit/Receive Differential Pair 5: This USB 2.0 signal pair can be routed to xHCI or EHCI Controller 1 through software and should map to a USB connector with one of the overcurrent OC Pins 0-3. USB2p6 USB2n6 12 6 I/O USB 2.0 Port 6 Transmit/Receive Differential Pair 6: This USB 2.0 signal pair can be mapped to xHCI or EHCI Controller 1 through software and should map to a USB connector with one of the overcurrent OC Pins 0-3. USB2p7 USB2n7 13 7 I/O USB 2.0 Port 7 Transmit/Receive Differential Pair 7: This USB 2.0 signal pair can be mapped to xHCI or EHCI Controller 1 through software and should map to a USB connector with one of the overcurrent OC Pins 0-3. USB2p8 USB2n8 4 8 I/O USB 2.0 Port 8 Transmit/Receive Differential Pair 8: This USB 2.0 signal pair can be mapped to xHCI or EHCI Controller 2 through software and should map to a USB connector with one of the overcurrent OC Pins 4-7. USB2p9 USB2n9 5 9 I/O USB 2.0 Port 9 Transmit/Receive Differential Pair 9: This USB 2.0 signal pair can be mapped to xHCI or EHCI Controller 2 through software and should map to a USB connector with one of the overcurrent OC Pins 4-7. Name Datasheet Description 63 Signal Description Table 2-2. USB Interface Signals (Sheet 2 of 3) xHCI Port EHCI Port Type USB2p10 USB2n10 6 10 I/O USB 2.0 Port 10 Transmit/Receive Differential Pair 10:This USB 2.0 signal pair can be mapped to xHCI or EHCI Controller 2 through software and should map to a USB connector with one of the overcurrent OC Pins 4-7. USB2p11 USB2n11 7 11 I/O USB 2.0 Port 11 Transmit/Receive Differential Pair 11: This USB 2.0 signal pair can be mapped to xHCI or EHCI Controller 2 through software and should map to a USB connector with one of the overcurrent OC Pins 4-7. USB2p12 USB2n12 10 12 I/O USB 2.0 Port 12 Transmit/Receive Differential Pair 12: This USB 2.0 signal pair can be mapped to xHCI or EHCI Controller 2 through software and should map to a USB connector with one of the overcurrent OC Pins 4-7. USB2p13 USB2n13 11 13 I/O USB 2.0 Port 13 Transmit/Receive Differential Pair 13: This USB 2.0 signal pair can be mapped to xHCI or EHCI Controller 2 through software and should map to a USB connector with one of the overcurrent OC Pins 4-7. O USB 3.0 Differential Transmit Pair 1: These are USB 3.0based outbound high-speed differential signals, mapped to High Speed I/O (HSIO) Port #1 and the xHCI Controller. It should map to a USB connector with one of the OC (overcurrent) pins 0-7. I USB 3.0 Differential Receive Pair 1: These are USB 3.0based inbound high-speed differential signals, mapped to High Speed I/O (HSIO) Port #1 and the xHCI Controller. It should map to a USB connector with one of the OC (overcurrent) pins 0-7. O USB 3.0 Differential Transmit Pair 2: These are USB 3.0based outbound high-speed differential signals, mapped to High Speed I/O (HSIO) Port #2 and the xHCI Controller. It should map to a USB connector with one of the OC (overcurrent) pins 0-7. I USB 3.0 Differential Receive Pair 2: These are USB 3.0based inbound high-speed differential signals, mapped to High Speed I/O (HSIO) Port #2 and the xHCI Controller. It should map to a USB connector with one of the OC (overcurrent) pins 0-7. Name USB3Tp1 USB3Tn1 USB3Rp1 USB3Rn1 USB3Tp2 USB3Tn2 USB3Rp2 USB3Rn2 USB3Tp3 USB3Tn3 1 1 2 2 3 - - - - - O Description USB 3.0 Differential Transmit Pair 3: These are USB 3.0based outbound high-speed differential signals, mapped to High Speed I/O (HSIO) Port 5 and the xHCI Controller. It should map to a USB connector with one of the OC (overcurrent) pins 0-7. Note: USB3Rp3 USB3Rn3 3 - I USB 3.0 Differential Receive Pair 3: These are USB 3.0based inbound high-speed differential signals, mapped to High Speed I/O (HSIO) Port 5 and the xHCI Controller. It should map to a USB connector with one of the OC (overcurrent) pins 0-7. Note: USB3Tp4 USB3Tn4 4 - O Use FITC to set the soft straps that select this port as USB 3.0 Port 3. Default configuration is PCIe Port 1. USB 3.0 Differential Transmit Pair 4: These are USB 3.0based outbound high-speed differential signals, mapped to High Speed I/O (HSIO) Port #6 and the xHCI Controller. It should map to a USB connector with one of the OC (overcurrent) pins 0-7. Note: 64 Use FITC to set the soft straps that select this port as USB 3.0 Port 3. Default configuration is PCIe Port 1. Use FITC to set the soft straps that select this port as USB 3.0 Port 4. Default configuration is PCIe Port 2. Datasheet Signal Description Table 2-2. USB Interface Signals (Sheet 3 of 3) Name USB3Rp4 USB3Rn4 xHCI Port 4 EHCI Port - Type I Description USB 3.0 Differential Receive Pair 4: These are USB 3.0based inbound high-speed differential signals, mapped to High Speed I/O (HSIO) Port #6 and the xHCI Controller. It should map to a USB connector with one of the OC (overcurrent) pins 0-7. Note: USB3Tp5 USB3Tn5 USB3Rp5 USB3Rn5 USB3Tp6 USB3Tn6 USB3Rp6 USB3Rn6 Datasheet 5 5 6 6 - - - - Use FITC to set the soft straps that select this port as USB 3.0 Port 4. Default configuration is PCIe Port 2. O USB 3.0 Differential Transmit Pair 5: These are USB 3.0based outbound high-speed differential signals, mapped to High Speed I/O (HSIO) Port #3 and the xHCI Controller. It should map to a USB connector with one of the OC (overcurrent) pins 0-7. I USB 3.0 Differential Receive Pair 5: These are USB 3.0based inbound high-speed differential signals, mapped to High Speed I/O (HSIO) Port #3 and the xHCI Controller. It should map to a USB connector with one of the OC (overcurrent) pins 0-7. O USB 3.0 Differential Transmit Pair 6: These are USB 3.0based outbound high-speed differential signals, mapped to High Speed I/O (HSIO) Port #4 and the xHCI Controller. It should map to a USB connector with one of the OC (overcurrent) pins 0-7. I USB 3.0 Differential Receive Pair 6: These are USB 3.0based inbound high-speed differential signals, mapped to High Speed I/O (HSIO) Port #4 and the xHCI Controller. It should map to a USB connector with one of the OC (overcurrent) pins 0-7. Overcurrent Indicators: These signals set corresponding bits in the USB controllers to indicate that an overcurrent condition has occurred. OC[7:0]# is the default (Native) function for these pins but they may be configured as GPIOs instead. OC0#/GPIO59 OC1#/GPIO40 OC2#/GPIO41 OC3#/GPIO42 OC4#/GPIO43 OC5#/GPIO9 OC6#/GPIO10 OC7#/GPIO14 - - I USBRBIAS - - O USB Resistor Bias: Analog connection point for an external resistor that is used to set transmit currents and internal load resistors. It is recommended that a 22.6 1% resistor to ground be connected to this pin. USBRBIAS# - - I USB Resistor Bias Complement: Analog connection point for an external resistor that is used to set transmit currents and internal load resistors. This signal should be connected directly to USBRBIAS. Notes: 1. OC pins are 3.3 V tolerant. 2. Sharing of OC pins is required to cover all 14 USB connectors but no more than 1 OC line may be connected to a USB connector. 3. OC[3:0]# should be connected with USB 2.0 ports 0-7 and any 4 of USB 3.0 ports 1-6. 4. OC[7:4]# should be connected with USB 2.0 ports 8-13 and any 4 of USB 3.0 ports 1-6. 65 Signal Description 2.3 PCI Express* Table 2-3. PCI Express* Signals (Sheet 1 of 2) Name Type Description PCI Express* Differential Transmit Pair 1: These are PCI Express 2.0-based outbound high-speed differential signals, and can be mapped to either High Speed I/O (HSIO) Port 5 or HSIO Port 13. PETp1 PETn1 Note: O Note: GbE can be mapped to PCIe Port 1 if PCIe Port 1 is selected at HSIO Port 5. GbE cannot be mapped to PCIe Port 1 if PCIe Port 1 is selected at HSIO Port 13. See Section 5.4 for details on GbE configuration and support. Use FITC to set the soft straps that select this port as muxed with USB 3.0 Port 3 or muxed with SATA Port 4. FITC does not allow multiplexing PCIe Port 1 with USB 3.0 Port 3 and SATA Port 4 simultaneously, and it is not a supported configuration. PCI Express* Differential Receive Pair 1: These are PCI Express 2.0-based inbound high-speed differential signals, and can be mapped to HSIO Port 5 or HSIO Port 13. PERp1 PERn1 Note: I Note: GbE can be mapped to PCIe Port 1 if PCIe Port 1 is selected at HSIO Port 5. GbE cannot be mapped to PCIe Port 1 if PCIe Port 1 is selected at HSIO Port 13. See Section 5.4 for details on GbE configuration and support. Use FITC to set the soft straps that select this port as muxed with USB 3.0 Port 3 or muxed with SATA Port 4. FITC does not allow multiplexing PCIe Port 1 with USB 3.0 Port 3 and SATA Port 4 simultaneously, and it is not a supported configuration. PCI Express Differential Transmit Pair 2: These are PCI Express 2.0-based outbound high-speed differential signals, and can be mapped to HSIO Port 6 or HSIO Port 14. PETp2 PETn2 Note: O Note: GbE can be mapped to PCIe Port 2 if PCIe Port 2 is selected at HSIO Port 6. GbE cannot be mapped to PCIe Port 2 if PCIe Port 2 is selected at HSIO Port 14. See Section 5.4 for details on GbE configuration and support. Use FITC to set the soft straps that select this port as muxed with USB 3.0 Port 4 or muxed with SATA Port 5. FITC does not allow multiplexing PCIe Port 2 with USB 3.0 Port 4 and SATA Port 5 simultaneously, and it is not a supported configuration. PCI Express Differential Receive Pair 2: These are PCI Express 2.0-based inbound high-speed differential signals, and can be mapped to HSIO Port 6 or HSIO Port 14. PERp2 PERn2 Note: I Note: 66 GbE can be mapped to PCIe Port 2 if PCIe Port 2 is selected at HSIO Port 6. GbE cannot be mapped to PCIe Port 2 if PCIe Port 2 is selected at HSIO Port 14. See Section 5.4 for details on GbE configuration and support. Use FITC to set the soft straps that select this port as muxed with USB 3.0 Port 4 or muxed with SATA Port 5. FITC does not allow multiplexing PCIe Port 2 with USB 3.0 Port 4 and SATA Port 5 simultaneously, and it is not a supported configuration. PETp3 PETn3 O PCI Express Differential Transmit Pair 3: These are PCI Express 2.0-based outbound high-speed differential signals, mapped to HSIO Port 7. PERp3 PERn3 I PCI Express Differential Receive Pair 3: These are PCI Express 2.0-based inbound high-speed differential signals, mapped to HSIO Port 7. PETp4 PETn4 O PCI Express Differential Transmit Pair 4: These are PCI Express 2.0-based outbound high-speed differential signals, mapped to HSIO Port 8. PERp4 PERn4 I PCI Express* Differential Receive Pair 4: These are PCI Express 2.0-based outbound high-speed differential signals, mapped to HSIO Port 8. PETp5 PETn5 O PCI Express Differential Transmit Pair 5: These are PCI Express 2.0-based outbound high-speed differential signals, mapped to HSIO Port 9. PERp5 PERn5 I PCI Express Differential Receive Pair 5: These are PCI Express 2.0-based outbound high-speed differential signals, mapped to HSIO Port 9. PETp6 PETn6 O PCI Express Differential Transmit Pair 6: These are PCI Express 2.0-based outbound high-speed differential signals, mapped to HSIO Port 10. PERp6 PERn6 I PCI Express Differential Receive Pair 6: These are PCI Express 2.0-based outbound high-speed differential signals, mapped to HSIO Port 10. PETp7 PETn7 O PCI Express Differential Transmit Pair 7: These are PCI Express 2.0-based outbound high-speed differential signals, mapped to HSIO Port 11. PERp7 PERn7 I PCI Express Differential Receive Pair 7: These are PCI Express 2.0-based outbound high-speed differential signals, mapped to HSIO Port 11. Datasheet Signal Description Table 2-3. PCI Express* Signals (Sheet 2 of 2) Name Type Description PETp8 PETn8 O PCI Express Differential Transmit Pair 8: These are PCI Express 2.0-based outbound high-speed differential signals, mapped to HSIO Port 12. PERp8 PERn8 I PCI Express Differential Receive Pair 8: These are PCI Express 2.0-based outbound high-speed differential signals, mapped to HSIO Port 12. PCIE_RCOMP I Impedance Compensation Input: Connected to a 7.5 K (1%) precision external pull-up resistor to 1.5 V. PCIE_IREF I Internal Reference Voltage: Connect directly to 1.5 V. 2.4 Serial ATA Interface Table 2-4. Serial ATA Interface Signals (Sheet 1 of 2) Name Type Description SATA_TXp0 SATA_TXn0 O Serial ATA Differential Transmit Pair 0: These outbound SATA Port 0 high-speed differential signals support 1.5 Gb/s, 3 Gb/s and 6 Gb/s, and are mapped to HSIO Port 15. In compatible mode, SATA Port 0 is the primary master of SATA Controller 1. SATA_RXp0 SATA_RXn0 I Serial ATA Differential Receive Pair 0: These inbound SATA Port 0 high-speed differential signals support 1.5 Gb/s, 3 Gb/s and 6 Gb/s, and are mapped to HSIO Port 15. In compatible mode, SATA Port 0 is the primary master of SATA Controller 1. SATA_TXp1 SATA_TXn1 O Serial ATA Differential Transmit Pair 1: These outbound SATA Port 1 high-speed differential signals support 1.5 Gb/s, 3 Gb/s and 6 Gb/s, and are mapped to HSIO Port 16. In compatible mode, SATA Port 1 is the secondary master of SATA Controller 1. SATA_RXp1 SATA_RXn1 I Serial ATA Differential Receive Pair 1: These inbound SATA Port 1 high-speed differential signals support 1.5 Gb/s, 3 Gb/s and 6 Gb/s, and are mapped to HSIO Port 16. In compatible mode, SATA Port 1 is the secondary master of SATA Controller 1. SATA_TXp2 SATA_TXn2 O Serial ATA Differential Transmit Pair 2: These outbound SATA Port 2 high-speed differential signals support 1.5 Gb/s, 3 Gb/s and 6 Gb/s, and are mapped to HSIO Port 17. In compatible mode, SATA Port 2 is the primary slave of SATA Controller 1. SATA_RXp2 SATA_RXn2 I Serial ATA Differential Receive Pair 2: These inbound SATA Port 2 high-speed differential signals support 1.5 Gb/s, 3 Gb/s and 6 Gb/s, and are mapped to HSIO Port 17. In compatible mode, SATA Port 2 is the primary slave of SATA Controller 1. SATA_TXp3 SATA_TXn3 O Serial ATA Differential Transmit Pair 3: These outbound SATA Port 3 high-speed differential signals support 1.5Gb/s, 3Gb/s and 6Gb/s, and are mapped to HSIO Port 18. In compatible mode, SATA Port 3 is the secondary slave of SATA Controller 1. SATA_RXp3 SATA_RXn3 I Serial ATA Differential Receive Pair 3: These inbound SATA Port 3 high-speed differential signals support 1.5 Gb/s, 3 Gb/s and 6 Gb/s, and are mapped to HSIO Port 18. In compatible mode, SATA Port 3 is the secondary slave of SATA Controller 1. SATA_TXp4 SATA_TXn4 O Serial ATA Differential Transmit Pair 4: These outbound SATA Port 4 high-speed differential signals support 1.5 Gb/s, 3 Gb/s and 6 Gb/s, and are mapped to HSIO Port 13. In compatible mode, SATA Port 4 is the primary master of SATA Controller 2. Note: SATA_RXp4 SATA_RXn4 I Serial ATA Differential Receive Pair 4: These inbound SATA Port 4 high-speed differential signals support 1.5 Gb/s, 3 Gb/s and 6 Gb/s, and are mapped to HSIO Port 13. In compatible mode, SATA Port 4 is the primary master of SATA Controller 2. Note: Datasheet Use FITC to set the soft straps that select this port as PCIe Port 1. Default configuration is SATA Port 4. Use FITC to set the soft straps that select this port as PCIe Port 1. Default configuration is SATA Port 4. 67 Signal Description Table 2-4. Serial ATA Interface Signals (Sheet 2 of 2) Name SATA_TXp5 SATA_TXn5 Type Description O Serial ATA Differential Transmit Pair 5: These outbound SATA Port 5 high-speed differential signals support 1.5 Gb/s, 3 Gb/s and 6 Gb/s, and are mapped to HSIO Port 14. In compatible mode, SATA Port 5 is the secondary master of SATA Controller 2. Note: SATA_RXp5 SATA_RXn5 I Serial ATA Differential Receive Pair 5: These inbound SATA Port 5 high-speed differential signals support 1.5 Gb/s, 3 Gb/s and 6 Gb/s, and are mapped to HSIO Port 14. In compatible mode, SATA Port 5 is the secondary master of SATA Controller 2. Note: 68 Use FITC to set the soft straps that select this port as PCIe Port 2. Default configuration is SATA Port 5. Use FITC to set the soft straps that select this port as PCIe Port 2. Default configuration is SATA Port 5. SATA0GP / GPIO21 I Serial ATA 0 General Purpose: When configured as SATA0GP, this is an input pin that is used as an interlock switch status indicator for SATA Port 0. Drive the pin to `0' to indicate that the switch is closed and to `1' to indicate that the switch is open. The default use of this pin is GPIO21. SATA1GP / GPIO19 I Serial ATA 1 General Purpose: When configured as SATA1GP, this is an input pin that is used as an interlock switch status indicator for SATA Port 1. Drive the pin to `0' to indicate that the switch is closed and to `1' to indicate that the switch is open. The default use of this pin is GPIO19. SATA2GP / GPIO36 I Serial ATA 2 General Purpose: When configured as SATA2GP, this is an input pin that is used as an interlock switch status indicator for SATA Port 2. Drive the pin to `0' to indicate that the switch is closed and to `1' to indicate that the switch is open. The default use of this pin is GPIO36. SATA3GP / GPIO37 I Serial ATA 3 General Purpose: When configured as SATA3GP, this is an input pin that is used as an interlock switch status indicator for SATA Port 3. Drive the pin to `0' to indicate that the switch is closed and to `1' to indicate that the switch is open. The default use of this pin is GPIO37. SATA4GP / GPIO16 I Serial ATA 4 General Purpose: When configured as SATA4GP, this is an input pin that is used as an interlock switch status indicator for SATA Port 4. Drive the pin to `0' to indicate that the switch is closed and to `1' to indicate that the switch is open. The default use of this pin is GPIO16. SATA5GP / GPIO49 I Serial ATA 5 General Purpose: When configured as SATA5GP, this is an input pin that is used as an interlock switch status indicator for SATA Port 5. Drive the pin to `0' to indicate that the switch is closed and to `1' to indicate that the switch is open. The default use of this pin is GPIO49. SATALED# OD O Serial ATA LED: This signal is an open-drain output pin driven during SATA command activity. It is to be connected to external circuitry that can provide the current to drive a platform LED. When active, the LED is on. When tri-stated, the LED is off. An external pull-up resistor to Vcc3_3 is required. SCLOCK / GPIO22 OD O SGPIO Reference Clock: The SATA controller uses rising edges of this clock to transmit serial data, and the target uses the falling edge of this clock to latch data. The SClock frequency supported is 32 kHz. If SGPIO interface is not used, this signal can be used as GPIO22. SLOAD / GPIO38 OD O SGPIO Load: The controller drives a `1' at the rising edge of SCLOCK to indicate either the start or end of a bit stream. A 4-bit vendor specific pattern will be transmitted right after the signal assertion. If SGPIO interface is not used, this signal can be used as GPIO38. SDATAOUT0 / GPIO39 SDATAOUT1 / GPIO48 OD O SATA_RCOMP I Impedance Compensation Input: Connected to a 7.5 K (1%) precision external pull-up resistor to 1.5 V. SATA_IREF I Internal Reference Voltage: Connect directly to 1.5 V. SGPIO Dataout: Driven by the controller to indicate the drive status in the following sequence: drive 0, 1, 2, 3, 4, 5, 0, 1, 2... If SGPIO interface is not used, the signals can be used as GPIO. Datasheet Signal Description 2.5 Clock Signals Table 2-5. Clock Interface Signals (Sheet 1 of 2) Name Type CLKOUT_ITPXDP_P CLKOUT_ITPXDP_N O CLKOUT_DP_P CLKOUT_DP_N O CLKOUT_DPNS_P CLKOUT_DPNS_N O CLKIN_DMI_P CLKIN_DMI_N I CLKOUT_DMI_P CLKOUT_DMI_N O CLKIN_SATA_P CLKIN_SATA_N I CLKIN_DOT96_P CLKIN_DOT96_N I 100 MHz PCIe* 3.0 specification compliant differential output to processor XDP/ITP connector on platform This Clock can be used for the 3rd PEG slot. Platform Over-clocking will not be supported when this clock is used for 3rd PEG slot. 135 MHz differential output for DisplayPort reference 135 MHz non-spread differential output for DisplayPort reference Unused. Tie each signal to GND through a 10 K resistor. 100 MHz PCIe 3.0 specification compliant differential output to processor Unused. Tie each signal to GND through a 10 Kresistor. Unused. Tie each signal to GND through a 10 Kresistor. XTAL25_IN I Connection for 25 MHz crystal to PCH oscillator circuit XTAL25_OUT O Connection for 25 MHz crystal to PCH oscillator circuit REFCLK14IN I Unused. Tie signal to GND through a 10 Kresistor. CLKOUT_PEG_A_P CLKOUT_PEG_A_N O 100 MHz PCIe 3.0 specification compliant differential output to PCI Express* Graphics device CLKOUT_PEG_B_P CLKOUT_PEG_B_N O 100 MHz PCIe 3.0 specification compliant differential output to a second PCI Express* Graphics device PEG_A_CLKRQ#/ GPIO47, PEG_B_CLKRQ# / GPIO56 Datasheet Description Clock Request Signals for PCIe Graphics slots. Can instead be used as GPIOs I Note: External pull-up resistor required if used for CLKREQ# functionality. Note: These pins are not available in desktop packages. CLKOUT_PCIE_P[7:0] CLKOUT_PCIE_N[7:0] O 100 MHz PCIe 2.0 specification compliant differential output to PCI Express devices CLKIN_GND_P CLKIN_GND_N I PCIECLKRQ0# PCIECLKRQ1# PCIECLKRQ3# PCIECLKRQ4# / / / / GPIO73, GPIO18, GPIO25, GPIO26 PCIECLKRQ2# / SMI#, PCIECLKRQ5# PCIECLKRQ6# PCIECLKRQ7# / GPIO20 / GPIO44, / GPIO45, / GPIO46 I/O Unused. Tie each signal to GND through a 10 Kresistor. Clock Request Signals for PCI Express 100 MHz Clocks Can instead by used as GPIOs Note: External pull-up resistor required if used for CLKREQ# functionality. Clock Request Signals for PCI Express 100 MHz Clocks Can instead by used as GPIOs I/O Note: Note: External pull-up resistor required if used for CLKREQ# functionality SMI# is for server/workstation only CLKOUT_33MHZ[4:0] O Single-Ended, 33 MHz outputs to various connectors/devices. One of these signals must be connected to CLKIN_33MHZLOOPBACK to function as a 33MHz clock loopback. This allows skew control for variable lengths of CLKOUT_33MHZ[4:0]. CLKIN_33MHZLOOPBACK I 33 MHz clock feedBack input, to reduce skew between PCH on-die 33 MHz clock and 33 MHz clock observed by connected devices. 69 Signal Description Table 2-5. Clock Interface Signals (Sheet 2 of 2) Name Type Description I/O Configurable as a GPIO or as a programmable output clock which can be configured as one of the following: * 33 MHz * 14.31818 MHz * 48/24 MHz * DC Output logic `0' I/O Configurable as a GPIO or as a programmable output clock which can be configured as one of the following: * 33 MHz * 14.31818 MHz * 48/24 MHz * DC Output logic `0' I/O Configurable as a GPIO or as a programmable output clock that can be configured as one of the following: * 33 MHz * 14.31818 MHz * 48/24 MHz * DC Output logic `0' CLKOUTFLEX31 / GPIO67 I/O Configurable as a GPIO or as a programmable output clock that can be configured as one of the following: * 33 MHz * 14.31818 MHz * 48/24 MHz * DC Output logic `0' DIFFCLK_BIASREF I/O Differential Clock Bias Reference: Connected to an external precision resistor (7.5 KW 1%) to 1.5 V ICLK_IREF I/O Internal Clock Bias Reference: Connect directly to a quiet 1.5 V supply. CLKOUTFLEX01 / GPIO64 CLKOUTFLEX11 / GPIO65 CLKOUTFLEX21 / GPIO66 Note: 1. It is highly recommended to prioritize 14.31818/24/48 MHz clocks on CLKOUTFLEX1 and CLKOUTFLEX3 outputs. Intel does not recommend configuring the 14.31818/24/48 MHz clocks on CLKOUTFLEX0 and CLKOUTFLEX2 if more than two 33 MHz clocks in addition to the feedback clock are used on the CLKOUT_33 MHz outputs. 2.6 Real Time Clock Interface Table 2-6. Real Time Clock Interface Name 70 Type Description RTCX1 Special Crystal Input 1: This signal is connected to the 32.768 kHz crystal. If no external crystal is used, then RTCX1 can be driven with the desired clock rate. Maximum voltage allowed on this pin is 1.2 V. RTCX2 Special Crystal Input 2: This signal is connected to the 32.768 kHz crystal. If no external crystal is used, then RTCX2 must be left floating. Datasheet Signal Description 2.7 External RTC Circuitry The PCH implements an internal oscillator circuit that is sensitive to step voltage changes in VccRTC. The following figure shows an example schematic recommended to ensure correct operation of the PCH RTC. Figure 2-2. Example External RTC Circuit VccDSW3_3 (see note 3) VCCRTC Schottky Diodes 1uF 0.1uF RTCX2 1 K 20 K Vbatt 20 K R1 10M 32.768 KHz Xtal RTCX1 1.0 uF 1.0 uF C1 C2 RTCRST# SRTCRST# Notes: 1. The Reference Designators used in this example are arbitrarily assigned. 2. The exact capacitor values and tolerances for C1 and C2 must be based on the crystal maker recommendations. 3. For platforms not supporting DeepSx, the VccDSW3_3 pins must be connected to the VccSUS3_3 pins. 4. Vbatt is voltage provided by the RTC battery (such as coin cell). 5. VccRTC, RTCX1, RTCX2, RTCRST#, and SRTCRST# are PCH pins. 6. VccRTC powers PCH RTC well. 7. RTCX1 is the input to the internal oscillator. 8. RTCX2 is the amplified feedBack (output) for the external crystal. Important: If a single-ended clock source, such as an oscillator, is used instead of the crystal to generate the RTC frequency, you must leave pin RTCX2 floating (no connect). 2.8 Interrupt Interface Table 2-7. Interrupt Signals Name SERIRQ PIRQ[D:A]# PIRQ[H:E]# / GPIO[5:2] Note: Datasheet Type Description I/OD Serial Interrupt Request: This pin implements the serial interrupt protocol. I/OD PCI Interrupt Requests: In non-APIC mode, the PIRQx# signals can be routed to interrupts 3, 4, 5, 6, 7, 9, 10, 11, 12, 14, or 15 as described in Section 5.9.6. Each PIRQx# line has a separate Route Control register. In APIC mode, these signals are connected to the internal I/O APIC in the following fashion: PIRQA# is connected to IRQ16, PIRQB# to IRQ17, PIRQC# to IRQ18, and PIRQD# to IRQ19. This frees the legacy interrupts. I/OD PCI Interrupt Requests: In non-APIC mode the PIRQx# signals can be routed to interrupts 3, 4, 5, 6, 7, 9, 10, 11, 12, 14, or 15 as described in Section 5.9.6. Each PIRQx# line has a separate Route Control register. In APIC mode, these signals are connected to the internal I/O APIC in the following fashion: PIRQE# is connected to IRQ20, PIRQF# to IRQ21, PIRQG# to IRQ22, and PIRQH# to IRQ23. This frees the legacy interrupts. If not needed for interrupts, these signals can be used as GPIO. PIRQ Interrupts can only be shared if it is configured as level sensitive. They cannot be shared if configured as edge triggered. 71 Signal Description 2.9 Processor Interface Table 2-8. Processor Interface Signals Name Type Description RCIN# I Keyboard Controller Reset Processor: The keyboard controller can generate INIT# to the processor. This saves the external OR gate with the PCH's other sources of INIT#. When the PCH detects the assertion of this signal, INIT# is generated using a VLW message to the processor. Note: The PCH will ignore RCIN# assertion during transitions to the S3, S4, and S5 states. PROCPWRGD O Processor Power Good: This signal should be connected to the processor UNCOREPWRGOOD input to indicate when the processor power is valid. PMSYNCH O Power Management Sync: Provides state information from the PCH to the processor. PECI I/O THRMTRIP# I Platform Environment Control Interface: Single-wire, serial bus. Thermal Trip: When low, this signal indicates that a thermal trip from the processor occurred, and the PCH will immediately transition to a S5 state. The PCH will not wait for the processor stop grant cycle since the processor has overheated. 2.10 Direct Media Interface (DMI) to Host Controller Table 2-9. Direct Media Interface Signals Name 72 Type Description DMI_TXP0 DMI_TXN0 O Direct Media Interface Differential Transmit Pair 0: This signal is an output from the PCH to the processor. DMI_RXP0 DMI_RXN0 I Direct Media Interface Differential Receive Pair 0: This signal is an input to the PCH from the processor. DMI_TXP1 DMI_TXN1 O Direct Media Interface Differential Transmit Pair 1: This signal is an output from the PCH to the processor. DMI_RXP1 DMI_RXN1 I Direct Media Interface Differential Receive Pair 1: This signal is an input to the PCH from the processor. DMI_TXP2 DMI_TXN2 O Direct Media Interface Differential Transmit Pair 2: This signal is an output from the PCH to the processor. DMI_RXP2 DMI_RXN2 I Direct Media Interface Differential Receive Pair 2: This signal is an input to the PCH from the processor. DMI_TXP3 DMI_TXN3 O Direct Media Interface Differential Transmit Pair 3: This signal is an output from the PCH to the processor. DMI_RXP3 DMI_RXN3 I Direct Media Interface Differential Receive Pair 3: This signal is an input to the PCH from the processor. DMI_RCOMP I Impedance Compensation Input: Connected to a 7.5 K (1%) precision external pull-up resistor to 1.5 V. DMI_IREF I Internal Reference Voltage: Connect directly to 1.5 V. Datasheet Signal Description 2.11 Intel(R) Flexible Display Interface (Intel(R) FDI) Table 2-10. Intel(R) Flexible Display Interface (Intel(R) FDI) Signals Signal Name 2.12 Type Description FDI_RXP0 FDI_RXN0 I FDI Display Link Receive Pair 0 FDI_RXP1 FDI_RXN1 I FDI_CSYNC O FDI Composite synchronization signal FDI_INT O Used for Display interrupts from PCH to processor. FDI_RCOMP I Impedance Compensation Input: Connected to an external precision resistor (7.5 K 1%) to 1.5 V FDI_IREF I Internal Reference Voltage: Connected to 1.5 V FDI Display Link Receive Pair 1 Analog Display/VGA DAC Signals Table 2-11. Analog Display Interface Signals Name 2.13 Type Description VGA_RED O A RED Analog Video Output: This signal is a VGA Analog video output from the internal color palette DAC. VGA_GREEN O A GREEN Analog Video Output: This signal is a VGA Analog video output from the internal color palette DAC. VGA_BLUE O A BLUE Analog Video Output: This signal is a VGA Analog video output from the internal color palette DAC. DAC_IREF I/O A Resistor Set: Set point resistor for the internal color palette DAC. A 649 resistor is required between DAC_IREF and motherboard ground. VGA_HSYNC O HVCMOS VGA Horizontal Synchronization: This signal is used as the horizontal sync (polarity is programmable) or "sync interval". 2.5 V output VGA_VSYNC O HVCMOS VGA Vertical Synchronization: This signal is used as the vertical sync (polarity is programmable). 2.5 V output. VGA_DDC_CLK I/O COD Monitor Control Clock VGA_DDC_DATA I/O COD Monitor Control Data VGA_IRTN I/O COD Monitor Current Return Digital Display Signals Table 2-12. Digital Display Signals (Sheet 1 of 2) Name Description DDPB_AUXP I/O Port B: DisplayPort* Aux DDPB_AUXN I/O Port B: DisplayPort Aux Complement DDPB_HPD Datasheet Type I Port B: HPD Hot-Plug Detect DDPB_CTRLCLK I/O Port B: HDMI* Port B Control Clock. DDPB_CTRLDATA I/O Port B: HDMI Port B Control Data. DDPC_AUXP I/O Port C: DisplayPort Aux 73 Signal Description Table 2-12. Digital Display Signals (Sheet 2 of 2) Name DDPC_AUXN DDPC_HPD Type I/O I Description Port C: DisplayPort Aux Complement Port C: HPD Hot-Plug Detect DDPC_CTRLCLK I/O Port C:HDMI Port C Control Clock DDPC_CTRLDATA I/O Port C:HDMI Port C Control Data DDPD_AUXP I/O Port D: DisplayPort Aux DDPD_AUXN I/O Port D: DisplayPort Aux Complement DDPD_HPD I Port D: Hot-Plug Detect DDPD_CTRLCLK I/O Port D:HDMI Port D Control Clock DDPD_CTRLDATA I/O Port D:HDMI Port D Control Data 2.14 Embedded DisplayPort* (eDP*) Backlight Control Signals Note: These signals can be left as No Connect (float) if eDP is not used. Table 2-13. Embedded DisplayPort* (eDP*) backlight control signals Name 2.15 Type Description eDP_VDDEN I/O eDP* Panel power Enable: Panel power control enable. This signal is also called VDD_dBL in the CPIS specification and is used to control the VDC source of the panel logic. eDP_BKLTEN I/O eDP Backlight Enable: Panel backlight enable control for eDP. This signal is also called ENA_BL in the CPIS specification and is used to gate power into the backlight circuitry. eDP_BKLTCTL I/O eDP Panel Backlight Brightness control: Panel brightness control for eDP. This signal also called VARY_BL in the CPIS specification and is used as the PWM Clock input signal Intel(R) High Definition Audio (Intel(R) HD Audio) Link Table 2-14. Intel(R) High Definition Audio (Intel(R) HD Audio) Link Signals (Sheet 1 of 2) Name Description (R) HDA_RST# O Intel High Definition Audio Reset: Master hardware reset to external codec(s). HDA_SYNC O Intel High Definition Audio Sync: 48 kHz fixed rate sample sync to the codec(s). This signal is also used to encode the stream number. HDA_BCLK O Intel High Definition Audio Bit Clock Output: 24.000 MHz serial data clock generated by the Intel High Definition Audio controller (the PCH). HDA_SDO 74 Type O Intel High Definition Audio Serial Data Out: Serial TDM data output to the codec(s). This serial output is double-pumped for a bit rate of 48 Mb/s for Intel High Definition Audio. Note: This signal is sampled as a functional strap. See Section 2.18 for more details. There is a weak integrated pull-down resistor on this pin. Datasheet Signal Description Table 2-14. Intel(R) High Definition Audio (Intel(R) HD Audio) Link Signals (Sheet 2 of 2) Name HDA_SDI[3:0] Type Description I Intel High Definition Audio Serial Data In [3:0]: Serial TDM data inputs from the codecs. The serial input is single-pumped for a bit rate of 24 Mb/s for Intel High Definition Audio. These signals have integrated pulldown resistors, which are always enabled. Note: HDA_DOCK_EN# / GPIO33 HDA_DOCK_RST# / GPIO13 2.16 During enumeration, the PCH will drive this signal. During normal operation, the CODEC will drive it. O Intel High Definition Audio Dock Enable: This signal controls the external Intel HD Audio docking isolation logic. This is an active low signal. When de-asserted, the external docking switch is in isolate mode. When asserted, the external docking switch electrically connects the Intel HD Audio dock signals to the corresponding PCH signals. This signal can instead be used as GPIO33. This signal defaults to GPIO33 mode after PLTRST#. BIOS is responsible for configuring GPIO33 to HDA_DOCK_EN# mode. O Intel High Definition Audio Dock Reset: This signal is a dedicated HDA_RST# signal for the codec(s) in the docking station. Aside from operating independently from the normal HDA_RST# signal, it otherwise works similarly to the HDA_RST# signal. This signal is shared with GPIO13. This signal defaults to GPIO13 mode after PLTRST#. BIOS is responsible for configuring GPIO13 to HDA_DOCK_RST# mode. Low Pin Count (LPC) Interface Table 2-15. Low Pin Count (LPC) Interface Signals Name 2.17 Type Description LPC Multiplexed Command, Address, Data: For LAD[3:0], internal pull-ups are provided. LAD[3:0] I/O LFRAME# O LPC Frame: LFRAME# indicates the start of an LPC cycle, or an abort. LDRQ0#, LDRQ1# / GPIO23 I LPC Serial DMA/Master Request Inputs: LDRQ[1:0]# are used to request DMA or bus master access. These signals are typically connected to an external Super I/O device. An internal pull-up resistor is provided on these signals. LDRQ1# may optionally be used as GPIO23. General Purpose I/O Signals The following table summarizes the GPIOs in the PCH. The control for the GPIO signals is handled through an independent 128-byte I/O space. The base offset for this space is selected by the GPIO_BAR register in D31:F0 configuration space. See Section 12.10 for details. Highlights of GPIO Features Datasheet a. GPIO pins powered from DSW: If pin is configured as GPIO then it follows the SUS well (does not follow DSW) and its content is wiped out when SUS is removed. b. Only GPIO[31:0] are blink-capable. c. When the default of a multiplexed GPIO is Native but the desired functionality is GPIO, care should be taken to ensure the signal is stable until it is initialized to GPIO functionality. 75 Signal Description d. Glitch-less Output means the signal is ensured to be stable (no glitch) during power on and when switching mode of operation from Native to GPIO or GPIO to Native. Glitch-less Input means the signal has built-in de-glitch protection that gates the input signal until power has become stable (the input is ignored during this time). e. The following GPIOs are capable of generating SMI#, SCI, or NMI: GPIO[60, 57, 56, 43, 27, 22, 21, 19, 17, 15:0]. f. GPIO_USE_SEL[31:0], GPIO_USE_SEL2[63:32] and GPIO_USE_SEL3[75:64] select whether the pin is selected to function as GPIO (GPIO_USE_SEL[x] = 1) or Native (GPIO_USE_SEL[x] = 0). However, the PCH Soft Straps (SPI Flash) take precedence if there is a mismatch with GPIO_USE_SEL. g. GP_IO_SEL[31:0], GP_IO_SEL[63:32] and GP_IO_SEL[75:64] select whether the pin is an output (GP_IO_SEL[x] = 0) or an input (GP_IO_SEL[x] = 1). The value written to or reported in this register is invalid when the pin is programmed to Native function. h. If the corresponding GPIO has been set as an input, and GPI_ROUT has been programmed for NMI functionality, the GPI_NMI_EN[15:0] is used to allow active-high or active-low NMI events (depending on the polarity selected by GPI_INV[31:0]). i. All the GP_RST_SEL registers are only resetable by RSMRST#. GPIO Configuration registers within the Core Well are reset whenever PWROK is deasserted. j. GPIO Configuration registers within the Suspend Well are reset when RSMRST# is asserted, CF9h reset (06h or 0Eh), or SYS_RESET# is asserted. However, CF9h reset and SYS_RESET# events can be masked from resetting the Suspend well GPIO by programming appropriate GPIO Reset Select (GPIO_RST_SEL) registers. See Section 12.10 for details. k. GPIO24 is an exception to the other GPIO Signals in the Suspend Well and is not reset by CF9h reset (06h or 0Eh) Table 2-16. General Purpose I/O Signals (Sheet 1 of 5) Glitch-less Power Well Default (Note 2) GPI Event GPIO0 Core GPI GPIO1 Core GPIO2 (Note 8) Name Description Input Output Yes No No Multiplexed with BMBUSY#. GPI Yes Yes No Desktop and Mobile: Available as GPIO1 only (Note 4). Server: Multiplexed with TACH1. Core GPI Yes No No GPIO3 (Note 8) Core GPI Yes No No GPIO4 (Note 8) Core GPI Yes No No GPIO5 (Note 8) Core GPI Yes No No GPIO6 Core GPI Yes Yes No Desktop and Mobile: Available as GPIO6 only (Note 4). Server: Multiplexed with TACH2. GPIO7 Core GPI Yes Yes No Desktop and Mobile: Available as GPIO7 only (Note 4). Server: Multiplexed with TACH3. GPIO8 Sus GPO Yes No No Unmultiplexed. GPIO9 Sus Native Yes No No Multiplexed with OC5#. When configured as GPIO, default direction is Input (GPI). 76 Multiplexed PIRQE#. Multiplexed PIRQF#. Multiplexed PIRQG#. Multiplexed PIRQH#. Datasheet Signal Description Table 2-16. General Purpose I/O Signals (Sheet 2 of 5) Glitch-less Power Well Default (Note 2) GPI Event GPIO10 Sus Native GPIO11 Sus Native GPIO12 DSW (Note 9) Native Yes GPIO13 Sus (Note 12) GPI GPIO14 Sus GPIO15 Name Description Input Output Yes No No Multiplexed with OC6#. When configured as GPIO, default direction is Input (GPI). Yes Yes No Multiplexed with SMBALERT#. When configured as GPIO, default direction is Input (GPI). No No Multiplexed with LAN_PHY_PWR_CTRL. GPIO / Native functionality is controlled using soft strap. When configured as GPIO, default direction is Output (GPO). (Note 11) Yes No No Mobile: Multiplexed with HDA_DOCK_RST#. Desktop: Available as GPIO13 only (Note 4). Native Yes No No Multiplexed with OC7#. When configured as GPIO, default direction is Input (GPI). Sus GPO Yes No Yes Unmultiplexed. GPIO16 Core GPI No No No Multiplexed with SATA4GP. (Note 11) GPIO17 Core GPI Yes Yes No Desktop and Mobile: Available as GPIO17 only (Note 4). Server: Multiplexed with TACH0. GPIO18 Core Native No No No Multiplexed with PCIECLKRQ1#. External pull-up resistor required for Native function. When configured as GPIO, default direction is Output (GPO). GPIO19 (Note 5) Core GPI Yes No No Multiplexed with SATA1GP. GPIO20 Core Native No No No Multiplexed with PCIECLKRQ2#. External pull-up resistor required for Native function. When configured as GPIO, default direction is Output (GPO). Server: Also available as SMI# (Note 18). GPIO21 Core GPI Yes No No Multiplexed with SATA0GP. GPIO22 Core GPI Yes No No Multiplexed with SCLOCK. GPIO23 Core Native No No No Multiplexed with LDRQ1#. GPIO24 (Note 1) Sus GPO No No Yes GPIO25 Sus Native No No No Multiplexed with PCIECLKRQ3#. External pull-up resistor required for Native function. When configured as GPIO, default direction is Output (GPO). GPIO26 Sus Native No No No Multiplexed with PCIECLKRQ4#. External pull-up resistor required for Native function. When configured as GPIO, default direction is Output (GPO). Datasheet Unmultiplexed. 77 Signal Description Table 2-16. General Purpose I/O Signals (Sheet 3 of 5) Name Power Well Default (Note 2) Glitch-less GPI Event Description Input Output GPIO27 DSW (Note 9) GPI No No No Unmultiplexed. Can be configured as wake input to allow wakes from Deep Sx but, since the pin is shared, the PCH counts on this pin remaining asserted until PLTRST# deasserts or the PCH may latch the pin assertion as a LAN wake request. * Intel LAN Present: This pin is connected to the LANWAKE# pin on the LAN PHY, is used to signal a ME or host wake to the PCH. The pin may also be driven by the platform to cause a host wake, but it must be de-asserted whenever PLTRST# is de-asserted and may only be used to wake the host (GPIO27 wake enable must always be set). * No Intel LAN Present: This pin does not have a specific usage model for connection on the board, but allows the OEM/ODM customers a custom method to wake from Deep Sx. GPIO28 Sus GPO No No Yes Unmultiplexed. Yes Multiplexed with SLP_WLAN#. GPIO / Native functionality is controlled using soft strap. When configured as GPIO, default direction is Output (GPO). (Note 11, 15) Yes Multiplexed with SUSPWRDNACK, SUSWARN#. SUSPWRDNACK mode is the default mode of operation. If the system supports Deep Sx, then subsequent boots will default to SUSWARN# mode. (Note 23) When configured as GPIO, default direction is Input (GPI). Yes Notes: 1. Toggling this pin at a frequency higher than 10 Hz is not supported. 2. Desktop: GPIO_USE_SEL[31] is internally hardwired to a 1b, which means GPIO mode is permanently selected and cannot be changed. 3. Mobile: This GPIO pin is permanently appropriated by the ME as MGPIO2 for ACPRESENT function (not available as a true GPIO). GPIO29 GPIO30 (Note 9) GPIO31 (Note 3) DSW (Note 9) Sus DSW (Note 9) Native Native GPI No No No No No No GPIO32 Core GPO No No No Desktop: Available as GPIO32 only (Note 4). Mobile: GPIO_USE_SEL2[0] is internally hardwired to a 0b, which means Native mode is permanently selected and cannot be changed (not available as GPIO). External pull-up to Core well is required for CLKRUN#. GPIO33 (Note 5) Core GPO No No No Desktop: Available as GPIO33 only (Note 4). Mobile: Also available as HDA_DOCK_EN#. GPIO34 Core GPI No No No Unmultiplexed. GPIO35 Core GPO No No Yes Desktop and Mobile: Available as GPIO35 only (Note 4). Server: Also available as NMI#. GPIO36 (Note 5) Core GPI No No No GPIO37 (Note 5) Core GPI No No No GPIO38 Core GPI No No No GPIO39 Core GPI No No No Multiplexed with SDATAOUT0. No Multiplexed with OC1#. When configured as GPIO, default direction is Input (GPI). GPIO40 78 Sus Native No No Multiplexed with SATA2GP. Multiplexed with SATA3GP. Multiplexed with SLOAD. Datasheet Signal Description Table 2-16. General Purpose I/O Signals (Sheet 4 of 5) Glitch-less Power Well Default (Note 2) GPI Event GPIO41 Sus Native GPIO42 Sus GPIO43 Name Description Input Output No No No Multiplexed with OC2#. When configured as GPIO, default direction is Input (GPI). Native No No No Multiplexed with OC3#. When configured as GPIO, default direction is Input (GPI). Sus Native Yes No No Multiplexed with OC4#. When configured as GPIO, default direction is Input (GPI). GPIO44 Sus Native No No No Multiplexed with PCIECLKRQ5#. External pull-up resistor required for Native function. When configured as GPIO, default direction is Input (GPI). GPIO45 Sus Native No No No Multiplexed with PCIECLKRQ6#. External pull-up resistor required for Native function. When configured as GPIO, default direction is Input (GPI). GPIO46 Sus Native No No No Multiplexed with PCIECLKRQ7#. External pull-up resistor required for Native function. When configured as GPIO, default direction is Input (GPI). GPIO47 Sus Native No No No Desktop and Server: This pin is not available in the package as GPIO or Native. Mobile: Multiplexed with PEG_A_CLKRQ#. GPIO48 Core GPI No No No Multiplexed with SDATAOUT1. GPIO49 Core GPI No Yes No Multiplexed with SATA5GP. (Note 11) GPIO50 Core GPI No No No Unmultiplexed. GPIO51 (Note 5) Core GPO No No No Unmultiplexed. GPIO52 Core GPI No No No Unmultiplexed. GPIO53 (Note 5) Core GPO No No No Unmultiplexed. GPIO54 Core GPI No No No Unmultiplexed. GPIO55 (Note 5) Core GPO No No No GPIO56 Sus Native Yes No No Desktop and Server: This pin is not available in the package as GPIO or Native. Mobile: Multiplexed with PEG_B_CLKRQ#. GPIO57 Sus GPI Yes No Yes Unmultiplexed. Can be re-purposed for NFC interface input. (Note 10) GPIO58 Sus Native No Yes No Multiplexed with SML1CLK. When configured as GPIO, default direction is Input (GPI). GPIO59 Sus Native No No No Multiplexed with OC0#. When configured as GPIO, default direction is Input (GPI). GPIO60 Sus Native Yes Yes No Multiplexed with SML0ALERT#. When configured as GPIO, default direction is Input (GPI). GPIO61 Sus Native No No Yes Multiplexed with SUS_STAT#. When configured as GPIO, default direction is Output (GPO). GPIO62 (Note 5) Sus Native No No No Multiplexed with SUSCLK (Note 13). When configured as GPIO, default direction is Output (GPO). Datasheet Unmultiplexed. 79 Signal Description Table 2-16. General Purpose I/O Signals (Sheet 5 of 5) Glitch-less Power Well Default (Note 2) GPI Event GPIO63 Sus Native GPIO64 Core GPIO65 Name Description Input Output No No Yes Multiplexed with SLP_S5#. When configured as GPIO, default direction is Output (GPO). Native No No No Multiplexed with CLKOUTFLEX0. When configured as GPIO, default direction is Output (GPO). Core Native No No No Multiplexed with CLKOUTFLEX1. When configured as GPIO, default direction is Output (GPO). GPIO66 Core Native No No No Multiplexed with CLKOUTFLEX2. When configured as GPIO, default direction is Output (GPO). GPIO67 Core Native No No No Multiplexed with CLKOUTFLEX3. When configured as GPIO, default direction is Output (GPO). GPIO68 Core GPI No Yes No Desktop and Mobile: Available as GPIO68 only (Note 4). Server: Multiplexed with TACH4. GPIO69 Core GPI No Yes No Desktop and Mobile: Available as GPIO69 only (Note 4). Server: Multiplexed with TACH5. GPIO70 Core Native No Yes No Desktop and Mobile: Available as GPIO70 only (Note 4). Server: Multiplexed with TACH6. (Note 11) GPIO71 Core Native No Yes No Desktop and Mobile: Available as GPIO71 only (Note 4). Server: Multiplexed with TACH7. (Note 11) GPIO72 DSW (Note 9) Native No No No Desktop: Available as GPIO72 only (Note 4). Mobile: Also available as BATLOW#. Requires external pull-up resistor to DSW well. GPIO73 Sus Native No No No Multiplexed with PCIECLKRQ0#. External pull-up resistor required for Native function. When configured as GPIO, default direction is Input (GPI). GPIO74 Sus Native No Yes No Multiplexed with SML1ALERT#/TEMP_ALERT#. When configured as GPIO, default direction is Input (GPI). Can be re-purposed for NFC interface input. (Note 10, 11, 21) GPIO75 Sus Native No Yes No Multiplexed with SML1DATA. When configured as GPIO, default direction is Input (GPI). Notes: 1. GPIO[24] register bits are not cleared by CF9h reset by default, it is programmable through GP_RST_SEL[24] 2. Internal pull-up or pull-down may be present when Native functionality is selected. Refer to Table 3-1 for more details. 3. Internal pull-down resistor may be enabled in Deep Sx mode based on DSX_CFG configuration bit, as follows: `1' (pin will be driven by platform in Deep Sx) -> Z; - `0' (pin will NOT be driven by platform in Deep Sx) -> Internal pull-down. Refer to DSX_CFG register (RCBA+3334h) for more details. 4. For pins that are available as GPIO-only: if the power-on default is Native, BIOS is still required to configure the pin as GPIO by writing to the pin's GPIO_USE_SEL register, even though the pin is only available as GPIO. 5. A functional strap also exists on this pin. 6. Glitch-less Inputs are ensured, by circuit design, to de-glitch the input. Glitch-less Outputs are ensured, by circuit design, to not generate any glitches on the output during power-on. 7. The GPIO pins which are capable of generating NMI message when it is configured as input, its GPI_ROUT register is configured NMI functionality and its corresponding GPI NMI Enable (GNE) bit is set. NMI event is positive edge trigger based on the signal and after GPI Inversion logic. 80 Datasheet Signal Description 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 2.18 When GPIO[5:2] are configured as output GPIOs, they behave in an open drain manner. This SUS well pin will be controlled by DSW logic. GPIO functionality is only available when the SUS well is powered. GPIO 74 or GPIO 57 can be used for NFC on a platform. The NFC option can be set through FITC in ME configuration settings. For GPIOs where GPIO versus Native Mode is configured using SPI Soft Strap, the corresponding GPIO_USE_SEL bits for these GPIOs have no effect. The GPIO_USE_SEL bits for these GPIOs may change to reflect the Soft-Strap configuration even though GPIO Lockdown Enable (GLE) bit is set. GPIO13 is located in the HDA Suspend well. It can only be used if VccsusHDA is powered. GPIO62 defaults as Native SUSCLK. If this pin is to be configured as GPIO, it is required that the board ensure that the 32.768 kHz toggle rate does not affect the receiving logic of the pin until it is set as GPIO. When switching from GPIO at logic 1 to the native functionality, the pin must not glitch low. A soft strap (PMC_SOFT_STRAP_2 register[7] GP23MGPIO3_SLPWLAN_SEL) to enable switching between SLP_WLAN# (default) or GP29/MPGIO3. By default the strap is 0b, which enables the SLP_WLAN# pin function when sus well is up. When soft strap is loaded and value is 1b, the pin returns to its regular GPIO or MGPIO mode while SLP_WLAN# function no longer exists. Also take into account of note 11. GPIO72 will default to mobile (native) until determining if this is mobile or desktop/server SKU. GPIO may toggle until after When strapped as SMI#, the pin is automatically configured as open drain. The SMI# function is only available in server/workstation SKU. The SMI# function is not the same as the SMI# events that the GPIOs can be configured to generate, as described in GPI_ROUT and ALT_GPI_SMI_EN. N/A N/A The choice of which native mode, SML1ALERT# or TEMP_ALERT#, is determined by a soft strap. N/A SUSPWRDNACK Mode is the default mode of operation. If the system supports DeepSx, then subsequent boots will default to SUSWARN# mode. Functional Straps The PCH implements hardware functional straps that are used to configure specific functions within the PCH and processor very early in the boot process, before BIOS or software intervention. Some are sampled at the rising edge of PWROK, while others at the rising edge of RSMRST# to select configurations (except as noted), and then revert later to their normal usage. When Descriptor Mode is enabled, the PCH will read Soft Strap data out of the SPI device prior to the de-assertion of reset to both the Intel Management Engine and the Host system. In some cases, the soft strap data may override the hardware functional straps. See Section 5.26.2 for information on Descriptor Mode. Datasheet 81 Signal Description Table 2-17. Functional Strap Definitions (Sheet 1 of 3) Signal Usage When Sampled Comment This signal has a weak internal pull-up. This field determines the destination of accesses to the BIOS memory range. Also controllable using Boot BIOS Destination bit (Chipset Config Registers: Offset 3410h:Bit 10). This strap is used in conjunction with Boot BIOS Destination Selection 1 strap. SATA1GP / GPIO19 Boot BIOS Strap bit 0 (BBS0) Rising edge of PWROK Bit11 Bit 10 Boot BIOS Destination 0 1 Reserved 1 0 Reserved 1 1 SPI (default) 0 0 LPC Notes: 1. The internal pull-up is disabled after PLTRST# de-asserts. 2. If option 00 (LPC) is selected, BIOS may still be placed on LPC, but the platform is required to have SPI flash connected directly to the PCH SPI bus with a valid descriptor in order to boot. 3. Boot BIOS Destination Select to LPC/PCI by functional strap or using Boot BIOS Destination Bit will not affect SPI accesses initiated by Intel ME or Integrated GbE LAN. 4. See Section 10.1.49 for additional information. 5. This signal is in the Core well. This signal has a weak internal pull-up. This field determines the destination of accesses to the BIOS memory range. Also controllable using Boot BIOS Destination bit (Chipset Config Registers: Offset 3410h:Bit 11). This strap is used in conjunction with Boot BIOS Destination Selection 0 strap. GPIO51 Boot BIOS Strap bit 1 (BBS1) Rising edge of PWROK Bit11 Bit 10 Boot BIOS Destination 0 1 Reserved 1 0 Reserved 1 1 SPI (default) 0 0 LPC Notes: 1. The internal pull-up is disabled after PLTRST# de-asserts. 2. If option 00 (LPC) is selected, BIOS may still be placed on LPC, but the platform is required to have SPI flash connected directly to the PCH's SPI bus with a valid descriptor in order to boot. 3. Boot BIOS Destination Select to LPC/PCI by functional strap or using Boot BIOS Destination Bit will not affect SPI accesses initiated by Intel ME or Integrated GbE LAN. 4. See Section 10.1.49 for additional information. 5. This signal is in the Core well. This signal has a weak internal pull-down. This signal only takes effect if DMI is configured in AC-coupled mode (server/workstation only). 0 = DMI RX is terminated to VSS. 1 = DMI RX is terminated to VCC/2. SATA2GP / GPIO36 82 DMI RX Termination Rising edge of PWROK Notes: 1. The internal pull-down is disabled after PLTRST# deasserts. 2. If DMI is operating in DC-coupled mode (such as Client applications), then DMI RX is terminated to VSS and the value of this strap is ignored by the PCH and does not take effect. 3. This signal is in the Core well. Datasheet Signal Description Table 2-17. Functional Strap Definitions (Sheet 2 of 3) Signal SATA3GP / GPIO37 Usage TLS Confidentiality When Sampled Rising edge of PWROK Comment This signal has a weak internal pull-down. 0 = Disable Intel ME Crypto Transport Layer Security (TLS) cipher suite (no confidentiality). 1 = Enable Intel ME Crypto Transport Layer Security (TLS) cipher suite (with confidentiality). Must be pulled up to support Intel(R) AMT with TLS and Intel SBA (Small Business Advantage) with TLS. Notes: 1. The internal pull-down is disabled after PLTRST# deasserts. 2. This signal is in the Core well. HDA_SDO Reserved Rising edge of PWROK This signal has a weak internal pull-down. Notes: 1. The internal pull-down is disabled after PLTRST# deasserts. 2. This signal is in the Suspend well. This signal has a weak internal pull-down. HDA_DOCK_EN# / GPIO33 INTVRMEN Reserved Integrated VRM Enable Rising edge of PWROK Always Notes: 1. The internal pull-down is disabled after PLTRST# deasserts. 2. This signal is in the Core well. This signal does not have an internal resistor; an external resistor is required. 0 = DCPSUS1, DCPSUS2 and DCPSUS3 are powered from an external power source (should be connected to an external VRM). External VR powering option is for Mobile Only; Desktop/Server/Workstation should not pull the strap low. 1 = Integrated VRMs enabled. DCPSUS1, DCPSUS2 and DCPSUS3 can be left as No Connect. Notes: 1. This signal is always sampled. 2. This signal is in the RTC well. GPIO62 / SUSCLK DSWVRMEN PLL On-Die Voltage Regulator Enable DeepSx Well OnDie Voltage Regulator Enable Rising edge of RSMRST# Always This signal has a weak internal pull-up. 0 = Disable PLL On-Die voltage regulator. 1 = Enable PLL On-Die voltage regulator. Notes: 1. The internal pull-up is disabled after RSMRST# de-asserts. 2. This signal is in the Suspend well. This signal does not have an internal resistor; an external resistor is required. 0 = Disable Integrated DeepSx Well (DSW) On-Die Voltage Regulator. This mode is only supported for testing environments. 1 = Enable DSW 3.3 V-to-1.05 V Integrated DeepSx Well (DSW) On-Die Voltage Regulator. This must always be pulled high on production boards. Notes: 1. This signal is always sampled. 2. This signal is in the RTC well. The signal has a weak internal pull-down. 0 = Disable "No Reboot" mode. 1 = Enable "No Reboot" mode (PCH will disable the TCO Timer system reboot feature). This function is useful when running ITP/XDP. SPKR Datasheet No Reboot Rising edge of PWROK Notes: 1. The internal pull-down is disabled after PLTRST# deasserts. 2. The status of this strap is readable using the NO REBOOT bit (Chipset Config Registers: RCBA + Offset 3410h:Bit 5). 3. See Section 10.1.49 for additional information. 4. This signal is in the Core well. 83 Signal Description Table 2-17. Functional Strap Definitions (Sheet 3 of 3) Signal Usage When Sampled GPIO53 Reserved Rising edge of PWROK Comment This signal has a weak internal pull-up. Notes: 1. The internal pull-up is disabled after PLTRST# de-asserts. 2. This signal is in the Core well. The signal has a weak internal pull-up. 0 = Enable "Top Swap" mode. 1 = Disable "Top Swap" mode. GPIO55 DDPB_CTRLDATA DDPC_CTRLDATA DDPD_CTRLDATA Note: 2.19 Rising edge of PWROK Top Swap Override Rising edge of PWROK Port B Detected Rising edge of PWROK Port C Detected Rising edge of PWROK Port D Detected Notes: 1. The internal pull-up is disabled after PLTRST# de-asserts. 2. Software will not be able to clear the Top Swap mode bit until the system is rebooted. 3. The status of this strap is readable using the Top Swap bit (Chipset Config Registers: RCBA + Offset 3414h:Bit 0). 4. This signal is in the Core well. This signal has a weak internal pull-down. 0 = Port B is not detected. 1 = Port B is detected. Notes: 1. The internal pull-down is disabled after PLTRST# deasserts. 2. This signal is in the Core well. This signal has a weak internal pull-down. 0 = Port C is not detected. 1 = Port C is detected. Notes: 1. The internal pull-down is disabled after PLTRST# deasserts. 2. This signal is in the Core well. This signal has a weak internal pull-down. 0 = Port D is not detected. 1 = Port D is detected. Notes: 1. The internal pull-down is disabled after PLTRST# deasserts. 2. This signal is in the Core well. See Section 3.1 for full details on pull-up/pull-down resistors. SMBus Interface Table 2-18. SMBus Interface Signals Name Description SMBDATA I/OD SMBus Data: External pull-up resistor is required. SMBCLK I/OD SMBus Clock: External pull-up resistor is required. SMBALERT# / GPIO11 84 Type I SMBus Alert: This signal is used to wake the system or generate SMI#. This signal may be used as GPIO11. Datasheet Signal Description 2.20 System Management Interface Table 2-19. System Management Interface Signals Name Type Description I Intruder Detect: This signal can be set to disable the system if box detected open. This signal status is readable, so it can be used like a GPI if the Intruder Detection is not needed. SML0DATA I/OD System Management Link 0 Data: SMBus link to external PHY. External pullup is required. SML0CLK I/OD System Management Link 0 Clock: SMBus link to external PHY. External pull-up is required. SML0ALERT# / GPIO60 O OD SMLink Alert 0: Output of the integrated LAN controller to external PHY. External pull-up resistor is required. This signal can instead be used as GPIO60. SML1ALERT# / TEMP_ALERT# / GPIO74 O OD SMLink Alert 1: Alert for the ME SMBus controller to optional Embedded Controller or BMC. A soft-strap determines the native function SML1ALERT# or TEMP_ALERT# usage. When soft-strap is 0, function is SML1ALERT#, when soft-strap is 1, function is TEMP_ALERT#. This pin can also be set to function as GPIO74. External pull-up resistor is required on this pin. SML1CLK / GPIO58 I/OD System Management Link 1 Clock: SMBus link to optional Embedded Controller or BMC. External pull-up resistor is required. This signal can instead be used as GPIO58. SML1DATA / GPIO75 I/OD System Management Link 1 Data: SMBus link to optional Embedded Controller or BMC. External pull-up resistor is required. This signal can instead be used as GPIO75. INTRUDER# 2.21 Controller Link Table 2-20. Controller Link Signals Signal Name Type Description O Controller Link Reset: Controller Link reset that connects to a Wireless LAN Device supporting Intel Active Management Technology. This signal is in the Suspend power well. CL_CLK I/O Controller Link Clock: Bi-directional clock that connects to a Wireless LAN Device supporting Intel Active Management Technology. This signal is in the Suspend power well. CL_DATA I/O Controller Link Data: Bi-directional data that connects to a Wireless LAN Device supporting Intel Active Management Technology. This signal is in the Suspend power well. CL_RST# 2.22 Serial Peripheral Interface (SPI) Table 2-21. Serial Peripheral Interface (SPI) Signals (Sheet 1 of 2) Name Datasheet Type Description SPI_CLK O SPI Clock: SPI clock signal, during idle the bus owner will drive the clock signal low. Supported frequencies are 20 MHz, 33 MHz and 50 MHz. SPI_CS0# O SPI Chip Select 0: Used to select the primary SPI Flash device. Note: This signal cannot be used for any other type of device than SPI Flash. SPI_CS1# O SPI Chip Select 1: Used to select an optional secondary SPI Flash device. Note: SPI_CS0# cannot be used for any other type of device than SPI Flash. 85 Signal Description Table 2-21. Serial Peripheral Interface (SPI) Signals (Sheet 2 of 2) Name 2.23 Type Description SPI_CS2# O SPI Chip Select 2: Used to select the TPM device if it is connected to the SPI interface, it cannot be used for any other type of device than TPM. Note: TPM can be configured through soft straps to operate over LPC or SPI, but no more than 1 TPM is allowed in the system. SPI_MOSI I/O SPI Master OUT Slave IN: Defaults as a data output pin for PCH in Dual Output Fast Read mode. Can be configured with a soft strap as a bidirectional signal (SPI_IO0) to support the new Dual I/O Fast Read, Quad I/O Fast Read and Quad Output Fast Read modes. SPI_MISO I/O SPI Master IN Slave OUT: Defaults as a data input pin for PCH in Dual Output Fast Read mode. Can be configured with a soft strap as a bidirectional signal (SPI_IO1) to support the new Dual I/O Fast Read, Quad I/O Fast Read and Quad Output Fast Read modes. SPI_IO2 I/O SPI Data I/O: A bidirectional signal used to support the new Dual I/O Fast Read, Quad I/O Fast Read and Quad Output Fast Read modes. This signal is not used in Dual Output Fast Read mode. SPI_IO3 I/O SPI Data I/O: A bidirectional signal used to support the new Dual I/O Fast Read, Quad I/O Fast Read and Quad Output Fast Read modes. This signal is not used in Dual Output Fast Read mode. Manageability Signals The following signals can be optionally used by the Intel ME supported applications and appropriately configured by Intel Management Engine Firmware. When configured and used as a manageability function, the associated host GPIO functionality is no longer available. If the manageability function is not used in a platform, the signal can be used as a host General Purpose I/O or a native function. The manageability signals are referred to as Management Engine GPIO pins (MGPIO pins), which are GPIO pins that can be controlled through Intel ME FW. Table 2-22. MGPIO Conversion Table Note: 86 MGPIO GPIO Well Default Usage 0 24 SUS - 1 30 SUS SUSWARN# or SUSPWRDNACK 2 31 SUS ACPRESENT 3 29 SUS SLP_WLAN# 4 60 SUS SML0ALERT# 5 57 SUS Required for NFC (assumes GPIO74 is not setup for NFC) 6 27 DSW Intel ME Wake Input 7 28 SUS - 8 74 SUS SML1ALERT#/TEMP_ALERT# or Required for NFC (assumes GPIO 57 is not setup for NFC) 9 16 MAIN SATA4GP# 10 49 MAIN SATA5GP# 11 58 SUS SML1CLK 12 75 SUS SML1DATA The information in the Default Usage column is not for server platforms. For information on server manageability signals, see Table 2-24. Datasheet Signal Description Table 2-23. Client Manageability Signals Name MGPIO6 Type I/O Power Well Description DSW Can be configured as a wake input for the Intel ME. This pin is implemented in the DSW in order to allow wakes from the DeepSx state. This pin does not have a specific usage model for connection on the board, but allows the OEM/ODM customers a custom method to wake from DeepSx. Table 2-24. Server Manageability Signals Type Power Well MGPIO2 I/O SUS SMBALERT# signal from PSU to PCH. This signal indicates the PSU may cause a system shutdown due to a momentary loss of AC input voltage or an over-temperature condition. MGPIO0, MGPIO1, MGPIO2, MGPIO3, MGPIO4, MGPIO5, MGPIO6, MGPIO7, MGPIO8 I/O See Table 2-22 Intel ME Firmware Recovery Mode Strap. These signals are inputs to the PCH to force Intel ME to stay in recovery boot loader. Name Description Note: See Table 2-22 for the MGPIO conversion table. 2.24 Power Management Interface Table 2-25. Power Management Interface Signals (Sheet 1 of 4) Name Type Description ACPRESENT: This input pin indicates when the platform is plugged into AC power or not. In addition to the previous Intel ME to EC communication, the PCH uses this information to implement the DeepSx policies. For example, the platform may be configured to enter DeepSx when in S4 or S5 and only when running on battery. This is powered by DeepSx Well. ACPRESENT / GPIO31 I Note: APWROK I Active Sleep Well (ASW) Power OK: When asserted, this signal indicates that power to the ASW sub-system is stable. BATLOW# / GPIO72 I This signal is muxed with GPIO31 but GPIO_USE_SEL[31] is internally hardwired to a 1b, which means GPIO mode is permanently selected and cannot be changed. Mobile: This GPIO pin is permanently appropriated by the Intel ME as MGPIO2 for ACPRESENT function. Desktop: This pin is only GPIO31, ACPRESENT is not supported. Battery Low: This signal is available in Mobile package only. An input from the battery to indicate that there is insufficient power to boot the system. Assertion will prevent wake from S3-S5 state. This signal can also be enabled to cause an SMI# when asserted. For the Mobile package, this signal is multiplexed with GPIO72. In the Desktop package, this signal is only available as GPIO72. This signal must be tied high to the VCCDSW3_3, which will be tied to VccSUS3_3 on DeepSx disabled platforms. Note: BMBUSY# / GPIO0 CLKRUN# (Mobile Only) / GPIO32 (Desktop Only) Datasheet See Table 2-16 for Desktop implementation pin requirements. I Bus Master Busy: Generic bus master activity indication driven into the PCH. This signal can be configured to set the PM1_STS.BM_STS bit. The signal can also be configured to assert indications transmitted from the PCH to the processor using the PMSYNCH pin. I/O LPC Clock Run: This signal is used to support LPC CLKRUN protocol. It connects to peripherals that need to request clock restart or prevention of clock stopping. Not available in Desktop. 87 Signal Description Table 2-25. Power Management Interface Signals (Sheet 2 of 4) Name DPWROK DRAMPWROK LAN_PHY_PWR_CT RL / GPIO12 PLTRST# Type Description I DPWROK: Power OK Indication for the VccDSW3_3 voltage rail. This input is tied together with RSMRST# on platforms that do not support DeepSx. This signal is in the RTC well. OD O DRAM Power OK: This signal should connect to the processor's SM_DRAMPWROK pin. The PCH asserts this pin to indicate when DRAM power is stable. This pin requires an external pull-up. LAN PHY Power Control: LAN_PHY_PWR_CTRL should be connected to LAN_DISABLE_N on the PHY. PCH will drive LAN_PHY_PWR_CTRL low to put the PHY into a low power state when functionality is not needed. O O Notes: 1. LAN_PHY_PWR_CTRL can only be driven low if SLP_LAN# is deasserted. 2. Signal can instead be used as GPIO12. Platform Reset: The PCH asserts PLTRST# to reset devices on the platform (such as SIO, FWH, LAN, processor, and so on). The PCH asserts PLTRST# during power-up and when S/W initiates a hard reset sequence through the Reset Control register (I/O port CF9h). The PCH drives PLTRST# active a minimum of 1 ms when initiated through the Reset Control register (I/O port CF9h). Note: PLTRST_PROC# PWRBTN# PLTRST# is in the VccSUS3_3 well. O Platform Reset Processor: A 1.0 V copy of PLTRST# pin. This signal is the main host platform reset and should directly connect to the processor pin PLTRSTIN#. No on-board logic is required to level shift the voltage of this signal. I Power Button: The Power Button will cause SMI# or SCI to indicate a system request to go to a sleep state. If the system is already in a sleep state, this signal will cause a wake event. If PWRBTN# is pressed for more than 4 seconds, this will cause an unconditional transition (power button override) to the S5 state. Override will occur even if the system is in the S1-S4 states. This signal has an internal pull-up resistor and has an internal 16 ms de-bounce on the input. This signal is in the DSW well. Power OK: When asserted, PWROK is an indication to the PCH that all of its core power rails have been stable for at least 5 ms. PWROK can be driven asynchronously. When PWROK is negated, the PCH asserts PLTRST#. 88 Notes: 1. It is required that the power rails associated with PCI/PCIe (typically the 3.3 V, 5 V, and 12 V core well rails) have been valid for 99 ms prior to PWROK assertion in order to comply with the 100 ms PCI 2.3/ PCIe* 2.0 specification on PLTRST# de-assertion. 2. PWROK must not glitch, even if RSMRST# is low. PWROK I RI# I Ring Indicate: This signal is an input from a modem. It can be enabled as a wake event, and this is preserved across power failures. RSMRST# I Resume Well Reset: This signal is used for resetting the resume power plane logic. This signal must be asserted for at least t201 after the suspend power wells are valid. When de-asserted, this signal is an indication that the suspend power wells are stable. SLP_A# O SLP_A#: This signal is used to control power to the active sleep well (ASW) of the PCH. SLP_LAN# O LAN Sub-System Sleep Control: When SLP_LAN# is de-asserted, it indicates that the PHY device must be powered. When SLP_LAN# is asserted, power can be shut off to the PHY device. SLP_LAN# will always be de-asserted in S0 and anytime SLP_A# is de-asserted. Datasheet Signal Description Table 2-25. Power Management Interface Signals (Sheet 3 of 4) Name Type Description WLAN Sub-System Sleep Control: When SLP_WLAN# is asserted, power can be shut off to the external wireless LAN device. SLP_WLAN# will always will be de-asserted in S0. SLP_WLAN#/ GPIO29 O Note: SLP_S3# O S3 Sleep Control: SLP_S3# is for power plane control. This signal shuts off power to all non-critical systems when in S3 (Suspend To RAM), S4 (Suspend to Disk), or S5 (Soft Off) states. SLP_S4# O S4 Sleep Control: SLP_S4# is for power plane control. This signal shuts power to all non-critical systems when in the S4 (Suspend to Disk) or S5 (Soft Off) state. Note: SLP_S5# / GPIO63 SLP_SUS# SUSACK# The selection between native and GPIO mode is based on a soft strap. The soft strap default is '0', SLP_WLAN# mode. Even though the pin is in the deep sleep well (DSW), the native and GPIO functionality is only available when the SUS well is powered. Set soft strap to `1' to use the GPIO mode. This pin must be used to control the DRAM power in order to use the PCH's DRAM power-cycling feature. O S5 Sleep Control: SLP_S5# is for power plane control. This signal is used to shut power off to all non-critical systems when in the S5 (Soft Off) states. This pin may also be used as GPIO63. O DeepSx Indication: When asserted (driven low), this signal indicates the PCH is in DeepSx state where internal Sus power is shut off for enhanced power saving. When de-asserted (driven high), this signal indicates exit from DeepSx state and Sus power can be applied to PCH. If DeepSx is not supported, this pin can be left unconnected. This pin is in the DSW power well. I SUSACK#: If DeepSx is supported, the EC/motherboard controlling logic must change SUSACK# to match SUSWARN# once the EC/motherboard controlling logic has completed the preparations discussed in the description for the SUSWARN# pin. Note: SUSACK# is only required to change in response to SUSWARN# if DeepSx is supported by the platform. This pin is in the Sus power well. SUS_STAT# / GPIO61 O Suspend Status: This signal is asserted by the PCH to indicate that the system will be entering a low power state soon. This can be monitored by devices with memory that need to switch from normal refresh to suspend refresh mode. It can also be used by other peripherals as an indication that they should isolate their outputs that may be going to powered-off planes. This pin may also be used as GPIO61. SUSCLK /GPIO62 O Suspend Clock: This clock is an output of the RTC generator circuit to use by other chips for refresh clock. This pin may also be used as GPIO62. O SUSWARN#: This pin asserts low when the PCH is planning to enter the DeepSx power state and remove Suspend power (using SLP_SUS#). The EC/motherboard controlling logic must observe edges on this pin, preparing for SUS well power loss on a falling edge and preparing for SUS well related activity (host/Intel ME wakes and runtime events) on a rising edge. SUSACK# must be driven to match SUSWARN# once the above preparation is complete. SUSACK# should be asserted within a minimal amount of time from SUSWARN# assertion as no wake events are supported if SUSWARN# is asserted but SUSACK# is not asserted. Platforms supporting DeepSx, but not wishing to participate in the handshake during wake and DeepSx entry may tie SUSACK# to SUSWARN#. This pin may be multiplexed with a GPIO for use in systems that do not support DeepSx. This pin is multiplexed with SUSPWRDNACK since it is not needed in DeepSx supported platforms. Reset type: RSMRST# This signal is multiplexed with GPIO30 and SUSPWRDNACK. SUSWARN# / SUSPWRDNACK / GPIO30 Datasheet 89 Signal Description Table 2-25. Power Management Interface Signals (Sheet 4 of 4) Name Description O SUSPWRDNACK: Active high. Asserted by the PCH on behalf of the Intel ME when it does not require the PCH Suspend well to be powered. Platforms are not expected to use this signal when the PCH's DeepSx feature is used. This signal is multiplexed with GPIO30 and SUSWARN#. SYS_PWROK I System Power OK: This generic power good input to the PCH is driven and utilized in a platform-specific manner. While PWROK always indicates that the core wells of the PCH are stable, SYS_PWROK is used to inform the PCH that power is stable to some other system component(s) and the system is ready to start the exit from reset. SYS_RESET# I System Reset: This signal forces an internal reset after being debounced. The PCH will reset immediately if the SMBus is idle; otherwise, it will wait up to 25 ms 2 ms for the SMBus to idle before forcing a reset on the system. I/OD PCI Express* Wake Event in Sx: This signal is in DSW and behaves as an input pin in Sx states. Sideband wake signal on PCI Express asserted by components requesting wake up. PCIe OBFF on this pin has been de-featured and is not supported. SUSPWRDNACK / SUSWARN# / GPIO30 WAKE# 2.25 Type Power and Ground Signals Table 2-26. Power and Ground Signals (Sheet 1 of 2) Name Description DCPRTC Decoupling: This signal is for RTC decoupling only. The signal requires decoupling. DCPSST Decoupling: Internally generated 1.5 V powered from Suspend Well. This signal requires decoupling. Decoupling is required even if this feature is not used. DCPSUS1 1.05 V Suspend well power. If INTVRMEN is strapped high, power to this well is supplied internally and this pin should be left as no connect. If INTVRMEN is strapped low, power to this well must be supplied by an external 1.05 V suspend rail. Note: DCPSUS2 Note: DCPSUS3 External VR mode applies to Mobile Only. 1.05 V Suspend well power for USB 3.0. If INTVRMEN is strapped high, power to this well is supplied internally and these pins should be left as no connect. If INTVRMEN is strapped low, power to this well must be supplied by an external 1.05 V suspend rail. Note: 90 External VR mode applies to Mobile Only. 1.05 V Suspend well power for USB 2.0. If INTVRMEN is strapped high, power to this well is supplied internally and this pin should be left as no connect. If INTVRMEN is strapped low, power to this well must be supplied by an external 1.05 V suspend rail. External VR mode applies to Mobile Only. DCPSUSBYP Decoupling: This signal is for decoupling internally generated 1.05 V DeepSx only. VCC 1.05 V supply for core well logic. This power may be shut off in S3, S4, S5, or G3 states. VCC3_3 3.3 V supply for core well I/O buffers. VCCASW 1.05 V supply for the Active Sleep Well. Provides power to the Intel ME and integrated LAN. This plane must be on in S0 and other times the Intel ME or integrated LAN is used. Datasheet Signal Description Table 2-26. Power and Ground Signals (Sheet 2 of 2) Name Description 3.3 V (can drop to 2.0 V min. in G3 state) supply for the RTC well. This power is not expected to be shut off unless the RTC battery is removed or completely drained. VCCRTC Note: VCCIO 1.05 V supply for I/O buffers. This power may be shut off in S3, S4, S5, Deep Sx or G3 states. VccSUS3_3 3.3 V supply for suspend well I/O buffers. This power may be shut off in DeepSx or G3 state. VCCSUSHDA Suspend supply for Intel HD Audio. This pin can be either 1.5 or 3.3 V. VCCVRM 1.5 V supply for internal VRMs. This power may be shut off in S3, S4, S5, Deep Sx, or G3 states. VCCADAC1_5 1.5 V supply for Display DAC Analog Power. This power may be shut off in S3, S4, S5, Deep Sx, or G3 states. VCCADACBG3_3 3.3 V supply for Display DAC Band Gap. This power may be shut off in S3, S4, S5, Deep Sx, or G3 states. VSS Ground. VCCCLK 1.05V Analog power supply for internal clock PLL. This power may be shut off in S3, S4, S5, Deep Sx, or G3 states. VCCCLK3_3 3.3 V Analog power supply for internal clock PLL. This power may be shut off in S3, S4, S5, Deep Sx, or G3 states. V_PROC_IO 1.05V supply for processor interface signals. This power may be shut off in S3, S4, S5, Deep Sx, or G3 states. Connect to the same supply as the PCH VCCIO; do not tie this signal to the processor. VCCDSW3_3 3.3 V supply for DeepSx wells. If the platform does not support Deep Sx, then tie to VccSUS3_3. VCCSPI VCCUSBPLL 2.26 Implementations should not attempt to clear CMOS by using a jumper to pull VccRTC low. Clearing CMOS can be done by using a jumper on RTCRST# or GPI. 3.3 V supply for SPI Controller Logic. This rail must be powered when VccASW is powered. Note: This rail can be optionally powered on 3.3 V Suspend power (VccSUS3_3) based on platform needs. 1.05V Analog power supply for USB PLL. This power may be shut off in S3, S4, S5, Deep Sx, or G3 states. Thermal Signals Table 2-27. Thermal Signals (Sheet 1 of 2) Signal Name PWM[3:0] Datasheet Type OD O Description Fan Pulse Width Modulation Outputs: These signals are Pulse Width Modulated duty cycle output signals used for fan control. These signals are 3.3 V tolerant. Note: TACH signals used on Server/Workstation Only; not supported on Mobile and Desktop. 91 Signal Description Table 2-27. Thermal Signals (Sheet 2 of 2) Signal Name Type Description I Fan Tachometer Inputs: Tachometer pulse input signal that is used to measure fan speed. This signal is connected to the "Sense" signal on the fan. The signals can instead be used as a GPIO. Note: TACH signals used on Server/Workstation Only; not supported on Mobile and Desktop. SST I/O Simple Serial Transport: Single-wire, serial bus. Connect this signal to SST compliant devices such as SST thermal sensors or voltage sensors. Note: TACH signals used on Server/Workstation Only; not supported on Mobile and Desktop. PECI I/O Platform Environment Control Interface: Single-wire, serial bus. TACH0 TACH1 TACH2 TACH3 TACH4 TACH5 TACH6 TACH7 / / / / / / / / GPIO17 GPIO1 GPIO6 GPIO7 GPIO68 GPIO69 GPIO70 GPIO71 TD_IREF 2.27 I Internal Reference Voltage: Thermal sensor low-cap analog reference bias current. This should be connected to Vss (ground) using an external resistor of 8.2 K. Miscellaneous Signals Table 2-28. Miscellaneous Signals (Sheet 1 of 2) Name Type Description INTVRMEN I Internal Voltage Regulator Enable: When pulled high, this signal enables the internal 1.05 V regulators for the Suspend well in the PCH. This signal must remain asserted for the VRMs to behave properly (no glitches allowed). This signal must be pulled-up to VCCRTC on desktop platforms and may optionally be pulled low on mobile platforms if using an external VR for the VCCSUS rail. DSWVRMEN I DeepSx Well Internal Voltage Regulator Enable: This signal enables the internal DSW 1.05 V regulators and must be always pulled-up to VCCRTC. SPKR O Speaker: The SPKR signal is the output of counter 2 and is internally "ANDed" with Port 61h Bit 1 to provide Speaker Data Enable. This signal drives an external speaker driver device, which in turn drives the system speaker. Upon PLTRST#, its output state is 0. Note: SPKR is sampled as a functional strap. There is a weak integrated pulldown resistor on SPKR pin. RTC Reset: When asserted, this signal resets register bits in the RTC well. RTCRST# I Notes: 1. Unless CMOS is being cleared (only to be done in the G3 power state), the RTCRST# input must always be high when all other RTC power planes are on. 2. In the case where the RTC battery is dead or missing on the platform, the RTCRST# pin must rise before the DPWROK pin. Secondary RTC Reset: This signal resets the manageability register bits in the RTC well when the RTC battery is removed. SRTCRST# SML1ALERT#/ TEMP_ALERT#/ GPIO74 92 I OD Notes: 1. The SRTCRST# input must always be high when all other RTC power planes are on. 2. In the case where the RTC battery is dead or missing on the platform, the SRTCRST# pin must rise before the RSMRST# pin. TEMP_ALERT#: This signal is used to indicate a PCH temperature out of bounds condition to an external EC, when PCH temperature is greater than value programmed by BIOS. An external pull-up resistor is required on this signal. Note: A soft-strap determines the native function SML1ALERT# or TEMP_ALERT# usage. When soft-strap is 0, function is SML1ALERT#, when soft-strap is 1, function is TEMP_ALERT#. Datasheet Signal Description Table 2-28. Miscellaneous Signals (Sheet 2 of 2) Type Description GPIO35 / NMI# (Server / Workstation Only) Name OD O NMI#: This is an NMI event indication to an external controller (such as a BMC) on server/workstation platforms. When operating as NMI event indication pin function (enabled when "NMI SMI Event Native GPIO Enable" soft strap [PCHSTRP9:bit 16] is set to 1), the pin is OD (open drain). PCIECLKRQ2# / GPIO20 / SMI# (Server / Workstation Only) OD O SMI#: This is an SMI event indication to an external controller (such as a BMC) on server/workstation platforms. When operating as SMI event indication pin function (enabled when "NMI SMI Event Native GPIO Enable" soft strap [PCHSTRP9:bit 16] is set to 1), the pin is OD (open drain). PME# 2.28 PCI Power Management Event: PCI peripherals drive PME# to wake the system from low-power states S1-S5. PME# assertion can also be enabled to generate an SCI from the S0 state. In some cases the PCH may drive PME# active due to an internal wake event. The PCH will not drive PME# high, but it will be pulled up to VccSUS3_3 by an internal pull-up resistor. PME# is still functional and can be used with PCI legacy mode on platforms using a PCIe-to-PCI bridge. Downstream PCI devices would need to have PME# routed from the connector to the PCH PME# pin. I/OD Testability Signals Table 2-29. Testability Signals Name Type Description JTAG_TCK I Test Clock Input (TCK): The test clock input provides the clock for the JTAG test logic. JTAG_TMS I Test Mode Select (TMS): The signal is decoded by the Test Access Port (TAP) controller to control test operations. JTAG_TDI I Test Data Input (TDI): Serial test instructions and data are received by the test logic at TDI. JTAG_TDO OD Test Data Output (TDO): TDO is the serial output for test instructions and data from the test logic defined in this standard. Note: 2.29 JTAG Pin definitions are from IEEE Standard Test Access Port and Boundary-Scan Architecture (IEEE Std. 1149.1-2001) Reserved / Test Pins Table 2-30. Test Pins (Sheet 1 of 2) Name Datasheet Description TP1 Intel Reserved Pin: Leave as No Connect (float, no breakout necessary). TP2 Intel Reserved Pin: Leave as No Connect (float, no breakout necessary). TP3 Intel Reserved Pin: Leave as No Connect (float, no breakout necessary). TP4 Intel Reserved Pin: Leave as No Connect (float, no breakout necessary). TP5 Intel Reserved Pin: Leave as No Connect (float, no breakout necessary). TP6 Intel Reserved Pin: Leave as No Connect (float, no breakout necessary). TP7 Intel Reserved Pin: Leave as No Connect (float, no breakout necessary). TP8 Intel Reserved Pin: Leave as No Connect (float, no breakout necessary). TP9 Intel Reserved Pin: Leave as No Connect (float, no breakout necessary). 93 Signal Description Table 2-30. Test Pins (Sheet 2 of 2) Name TP10 Description Intel Reserved Pin: Leave as No Connect (float, no breakout necessary). TP11 Intel Reserved Pin: Leave as No Connect (float, no breakout necessary). TP12 Intel Reserved Pin: Leave as No Connect (float, no breakout necessary). TP13 Intel Reserved Pin: Leave as No Connect (float, no breakout necessary). TP14 Intel Reserved Pin: Must have a pull-up resistor to VCC3_3. Standard resistor value in the range of 4.7 K to 15 K TP15 Intel Reserved Pin: Leave as No Connect (float, no breakout necessary). TP16 Intel Reserved Pin: Leave as No Connect (float, no breakout necessary). TP17 Intel Reserved Pin: Leave as No Connect (float, no breakout necessary). TP18 Intel Reserved Pin: Leave as No Connect (float, no breakout necessary). TP19 Intel Reserved Pin: Leave as No Connect (float, no breakout necessary). TP20 Intel Reserved Pin: Leave as No Connect (float, no breakout necessary). TP21 Intel Reserved Pin: Leave as No Connect (float, no breakout necessary). TP22 Intel Reserved Pin: Leave as No Connect (float, no breakout necessary). TP23 Intel Reserved Pin: Leave as No Connect (float, no breakout necessary). TP24 Intel Reserved Pin: Leave as No Connect (float, no breakout necessary). TP25 Intel Reserved Pin: Leave as No Connect (float, no breakout necessary). Note: The Test Point descriptions provided in this table apply to both Desktop and Mobile packages. 94 Datasheet PCH Pin States 3 PCH Pin States 3.1 Integrated Pull-Ups and Pull-Downs Table 3-1. Integrated Pull-Up and Pull-Down Resistors (Sheet 1 of 2) Signal Resistor Type Nominal Notes Pull-down 15K 4 Pull-up 20K 3, 7, 24 SATA2GP/GPIO36, SATA3GP/GPIO37, SPKR, DDP[B:D]_CTRLDATA Pull-down 20K 3, 7 HDA_DOCK_EN#, HDA_SDO Pull-down 15K 2, 7, 12, 24 SATA4GP/GPIO16, SATA5GP/GPIO49 Pull-up 20K 3, 5 PCIECLKRQ5#/GPIO44, PCIECLKRQ7#/GPIO46, GPIO8 Pull-up 20K 3, 11 USB2p/n[13:0] SATA1GP/GPIO19, SUSCLK/GPIO62, GPIO55, GPIO53, GPIO51, NMI# Pull-up 20K 3, 6, 24 USB3[T/R] [p/n] [6:1] Pull-down 15K 4 HDA_SDI[3:0], HDA_SYNC Pull-down 15K 2, 12 SPI_CLK, SPI_CS[2:0]# Pull-up 20K 3, 23 Pull-up or Pull-down 20K 3, 22 Pull-up 20K 3, 8 Pull-down 350 17 Pull-up 20K 3 Pull-up 20K 3, 19, 24 Pull-down 10K 3, 16, 24 SPI_MOSI SPI_MISO, SPI_IO3, SPI_IO2 PECI LAD[3:0], LDRQ0#, LDRQ1# TACH[7:0] SST PWRBTN# Pull-up 20K 3 WAKE# Pull-down 20K 3, 9, 19 GPIO31 (ACPRESENT) Pull-down 20K 3, 9 Pull-up 20K 2 Pull-down 20K 3, 9, 20 Pull-up 20K 3 Pull-up/Pull-down 31.25/100 13 SUSACK# GPIO27 PME# CL_CLK, CL_DATA Datasheet 95 PCH Pin States Table 3-1. Integrated Pull-Up and Pull-Down Resistors (Sheet 2 of 2) Signal Resistor Type Nominal Notes Pull-down 20K 1, 10 SMI# Pull-up 20K 3, 9, 24 JTAG_TDI, JTAG_TMS Pull-up 20K 3 JTAG_TCK Pull-down 20K 3 PET/R p/n[8:1], USB3T/R p/n[6:1], SATA_TX/RX p/n [6:1] Pull-up or Pull-down 50 14 FDI_RX p/n[1:0], DMI_TX/RX p/n[3:0] Pull-up or Pull-down 50 14 CLKOUT_33MHZ[4:0], CLKOUTFLEX[3:0]/GPIO[67:64] Notes: 1. Simulation data shows that these resistor values can range from 10 k to 45 k. 2. Simulation data shows that these resistor values can range from 9 k to 50 k. 3. Simulation data shows that these resistor values can range from 15 k to 40 k. 4. Simulation data shows that these resistor values can range from 14.25 k to 24.8 k. 5. GPIO16 has two native functions - the 1st native function (SATAP4_PCIEP1_SELECT) is selected if the Flex I/O soft strap SATAP4_PCIEP1_MODE = 11b and takes precedence over any other assignments to this pin (that is, if this is selected, writes to GPIO_USE_SEL are ignored). If SATAP4_PCIEP1_MODE is not set to 11b, the GPIO_USE_SEL register can be used to select the 2nd native function (SATA4GP) or GPIO functionality. Setting SATAP4_PCIEP1_MODE = 11b also enables an internal pull-up resistor in this pin to allow Flexible I/O selection of SATA Port 4 or PCIe Port 1 to be done based on the type of card installed (If sampled value = 1, select SATA; if sampled value = 0, select PCIe). The same behavior is true of pin SATA5GP/GPIO49 when the soft strap SATAP5_PCIEP2_MODE = 11b. Soft straps are handled through FITc. 6. When operating as NMI# event indication pin function, the pin is open drain but the PCH provides an internal pull-up to ensure the pin does not float. 7. This signal is a PCH functional strap; the pull-up or pull-down on this signal is disabled after it is sampled as a PCH functional strap. 8. This signal has a weak internal pull-up that is always on. 9. 9When operating as SMI# event indication pin function, the pin is open drain but the PCH provides an internal pull-up to ensure the pin does not float. 10. The pull-down is disabled after the pins are driven strongly to logic 0 when PWROK is asserted. 11. The pull-up or pull-down on this signal is disabled after RSMRST# de-asserts. This pin is not a functional strap. 12. The internal pull-down on HDA_SYNC and HDA_SDO is enabled during reset. 13. The Controller Link Clock and Data buffers use internal pull-up or pull-down resistors to drive a logical 1 or 0. 14. Termination resistors may be present if signal is enabled (that is, related Port is not disabled). These resistors appear to be strong pull-downs or pull-ups on the signals. 15. Internal pull-down resistor may be enabled in Deep Sx mode based on DSX_CFG configuration bit, as follows: `1' (pin will be driven by platform in Deep Sx) -> Z; - `0' (pin will NOT be driven by platform in Deep Sx) -> Internal pull-down. Refer to DSX_CFG register (RCBA+3334h) for more details. 16. When the interface is in BUS IDLE, the internal pull-down of 10 k is enabled. In normal transmission, a 400 pull-down takes effect, the signal will be overridden to logic 1 with pull-up resistor (37 ) to VCC 1.5 V. 17. This is a 350- normal pull-down, signal will be overridden to logic 1 with pull-up resistor (31 ) to VCC 1.05 V. 18. N/A 19. Regardless of internal pull-up or pull-down, an external pull-up resistor is still required. 20. External pull-up if Intel wired LAN is present (pull-up to SUS/DSW based on deepest wake on LAN support desired). 21. N/A 22. Weak internal pull-up resistor is enabled when APWROK is de-asserted and is switched to a weak internal pull-down resistor when APWROK and PLTRST# are both asserted. 23. Signals are tri-stated with weak pull-up resistors when APWROK is de-asserted. SPI_CS1# remains tristated with a weak pull-up resistor when APWROK and PLTRST# are both asserted. 24. Some signals may not be available in all SKUs. Check signal and SKU descriptions. 96 Datasheet PCH Pin States 3.2 Output Signals Planes and States Table 3-2 shows the power plane associated with the output and I/O signals, as well as the state at various times. Within the table, the following terms are used: Note: "DL" PCH drives low. "DH" PCH drives high. "IPU" Internal pull-up. "IPD" Internal pull-down. "T" Toggling or signal is transitioning because function not stopping. "High-Z" Tri-state. PCH not driving the signal high or low. "Defined" Driven to a level that is defined by the function or external pullup/pull-down resistor (will be high or low). "Off" The power plane is off; PCH is not driving when configured as an output or sampling when configured as an input. Pin state within table assumes interfaces are idle and default pin configuration for different power states. Signal levels are the same in S3, S4 and S5, except as noted. In general, PCH suspend well signal states are indeterminate and undefined and may glitch prior to RSMRST# de-assertion. PCH core well signal states are indeterminate and undefined and may glitch prior to PWROK assertion. However, this does not apply to THRMTRIP# as this signal is determinate and defined prior to PWROK assertion. DSW indicates PCH Deep Sx Well. This state provides a few wake events and critical context to allow system to draw minimal power in S3, S4 or S5 states. In general, PCH DSW signal states are indeterminate, undefined and may glitch prior to DPWROK assertion. The signals that are determinate and defined prior to DPWROK assertion will have a note added as a reference. ASW indicates PCH Active Sleep Well. This power well contains functionality associated with active usage models while the host system is in Sx. Datasheet 97 PCH Pin States Table 3-2. Output Signals - Power Plane and States in Desktop, Mobile, and Server Configurations (Sheet 1 of 4) Signal Name Power Plane During Reset23 Immediately after Reset23 S3/S4/S5 Deep Sx USB Interface USB2p/n[13:0] 24 USB3Tp/n[4:3] , USB3Tp/ n[6:5, 2:1] Suspend IPD IPD IPD Off Suspend IPD1 IPD1 S3 High-Z S4 and S5 Off Off IPD1 IPD1 Off Off 1 1 IPD Off Off Off PCI Express* PETp/n[2:1] 24 PETp/n[8:3] Suspend or Core5 Core IPD SATA Interface Core IPU1 IPU1 Off SATA_TXp/n[5:4]24 Core IPU1 IPU1 Off Off SATALED# Core High-Z High-Z Off Off SATA_TXp/n[3:0] SCLOCK Core High-Z High-Z Off Off SLOAD Core High-Z High-Z Off Off SDATAOUT[1:0] Core High-Z High-Z Off Off Clocking Signals CLKOUT_ITPXDP_P/N Core T (platform dependent) T (platform dependent) Off Off CLKOUT_DP_P/N Core T T Off Off CLKOUT_DPNS_P/N Core T T Off Off CLKOUT_DMI_P/N Core T T Off Off XTAL25_OUT Core High-Z High-Z Off Off CLKOUT_PEG_A_P/N Core T T Off Off CLKOUT_PEG_B_P/N Core T T Off Off CLKOUT_PCIE_P/N[7:0] Core T T Off Off CLKOUT_33MHZ[4:0] Core T T Off Off CLKOUTFLEX[3:0] Core T (platform dependent) T (platform dependent) Off Off DIFFCLK_BIASREF Core High-Z High-Z Off Off ICLK_IREF Core High-Z High-Z Off Off Interrupt Interface SERIRQ Core High-Z High-Z Off Off PIRQ[D:A]# Core High-Z High-Z Off Off PIRQ[H:E]# Core High-Z High-Z Off Off NMI#9 Core IPU IPU Off Off Processor Interface 98 PROCPWRGD Core DL DH Off Off PMSYNCH Core DL DL Off Off Datasheet PCH Pin States Table 3-2. Output Signals - Power Plane and States in Desktop, Mobile, and Server Configurations (Sheet 2 of 4) Signal Name Power Plane During Reset23 Immediately after Reset23 S3/S4/S5 Deep Sx IPU or IPD1, 21 Off Off 2 Off Off High-Z2 Off Off DMI DMI_TXp/n[3:0] Core Intel IPU or (R) IPD1, 21 (R) Flexible Display Interface (Intel 2 FDI_CSYNC Core High-Z FDI_INT Core High-Z2 High-Z FDI) Analog Display / VGA DAC Signals VGA_RED, VGA_GREEN, VGA_BLUE Core High-Z High-Z Off Off DAC_IREF Core High-Z DL Off Off VGA_HSYNC Core DL DL Off Off VGA_VSYNC Core DL DL Off Off VGA_DDC_CLK Core High-Z High-Z Off Off VGA_DDC_DATA Core High-Z High-Z Off Off VGA_IRTN Core High-Z High-Z Off Off Digital Display Interface DDP[D:B]_AUXP/N Core IPD IPD Off Off DDPB_CTRLCLK, DDPC_CTRLCLK, DDPD_CTRLCLK Core High-Z High-Z Off Off DDPB_CTRLDATA, DDPC_CTRLDATA, DDPD_CTRLDATA Core IPD3 High-Z Off Off eDP_VDD_EN Core DL DL Off Off eDP_BKLTEN Core DL DL Off Off eDP_BKLTCTL Core DL DL Off Off Intel(R) 4 High Definition Audio Interface (Intel(R) HD Audio) HDA_RST# , HDA_BCLK4 Suspend DL DL DL Off HDA_SYNC26, HDA_SDO26 Suspend IPD IPD IPD Off HDA_DOCK_EN#10 Core IPD IPD Off Off HDA_DOCK_RST#10 Suspend25 High-Z High-Z8 High-Z8 Off LPC Interface LAD[3:0] Core IPU IPU Off Off LFRAME# Core DH DH Off Off Non-Multiplexed GPIO Signals GPIO85 Suspend IPU DH DH Off GPIO155, 9 Suspend DL DL DL Off Suspend DL DL DL Off GPIO24 Datasheet 9 99 PCH Pin States Table 3-2. Output Signals - Power Plane and States in Desktop, Mobile, and Server Configurations (Sheet 3 of 4) Signal Name Power Plane During Reset23 Immediately after Reset23 S3/S4/S5 Deep Sx GPIO289 Suspend DL DL DL Off Core DL (Mobile); DH (Desktop) DL (Mobile); DH (Desktop) Off Off GPIO[53, 51] Core IPU DH Off Off GPIO55 Core IPU DL DL Off High-Z High-Z Off CLKRUN# SMBus Interface SMBCLK, SMBDATA Suspend High-Z System Management Interface SML0DATA Suspend High-Z High-Z High-Z Off SML0CLK Suspend High-Z High-Z High-Z Off 7 SML0ALERT# Suspend High-Z High-Z SML1ALERT# Suspend High-Z High-Z SML1CLK Suspend High-Z High-Z High-Z Off SML1DATA Suspend High-Z High-Z High-Z Off High-Z Off High-Z Off Controller Link CL_RST#11 11 CL_CLK CL_DATA11 Suspend DL DH DH Off Suspend Terminated12 Terminated12 IPD Off Suspend Terminated12 Terminated12 IPD Off SPI Interface SPI_CLK ASW DL DL DL Off SPI_CS0# SPI_CS1# ASW DH DH DH Off ASW IPU DH DH Off SPI_CS2# SPI_MOSI ASW DH DH DH Off ASW IPD DL DL Off SPI_MISO ASW IPU IPU IPU Off SPI_IO2 ASW IPU IPU IPU Off SPI_IO3 ASW IPU IPU IPU Off Power Management DRAMPWROK9 Suspend DL High-Z S3 High-Z, S4 and S5 DL Off LAN_PHY_PWR_CTRL DSW DL DL DL DL PLTRST# Suspend DL DH DL Off PLTRST_PROC# Core DL DH DL Off SLP_A#9, 11 DSW DL DH DH DL SLP_LAN#9 DSW DL DL DL/DH16 DL/DH16 SLP_WLAN#9 DSW DL DL DL/DH16 DL/DH16 SLP_S3#9 DSW DL DH DL DL DSW DL DH S3 DH, S4 and S5 DL DL/DH17 SLP_S4#9 100 Datasheet PCH Pin States Table 3-2. Output Signals - Power Plane and States in Desktop, Mobile, and Server Configurations (Sheet 4 of 4) Signal Name SLP_S5#9 Power Plane During Reset23 Immediately after Reset23 S3/S4/S5 Deep Sx Suspend DL DH S3 and S4 DH, S5 DL DL SLP_SUS#9 DSW DL DH DH DL SUS_STAT# Suspend DL DH18 DL Off SUSCLK Suspend IPU SUSWARN#/ SUSPWRDNACK9, 19 Suspend DL T Off DL DL OFF22 DL Off Off Thermal Signals PWM[3:0] Core SST Suspend PECI Core DL DL 20 DL DL 20 DL DL 20 Off Off Off Off Off Miscellaneous Signals SPKR5 Core TEMP_ALERT# Suspend High-Z High-Z High-Z Off JTAG_TDO Suspend High-Z High-Z High-Z Off Notes: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. Datasheet IPD DL This is a strong pull-down (or pull-up, as applicable). If the port is disabled, signal is tri-stated. External 2.2 K Pull-Up when used. The internal pull-down on HDA_BCLK and HDA_RST# are enabled when PWROK is de-asserted. When GCTL.CRST# bit is set, the HDA_BCLK pin will start to toggle. The power well depends on whether the PCIe port is being multiplexed with USB3 (suspend) or with SATA (core). N/A. N/A. This pin will be driven High when Dock Attach bit is set (Docking Control Register D27:F0 Offset 4Ch). The pin output shall not glitch during power up sequence. Native functionality multiplexed with these GPIOs are not used in Desktop configurations. The state of signals in S3-S5 will be defined by Intel ME Policies. The terminated state is when the I/O buffer pull-down is enabled. N/A. N/A. N/A. Pin may toggle between RSMRST# de-assertion to PLTRST# de-assertion, based on ME firmware configuration. Sx and DSx behavior is based on wake events and ME state/policy. When the platform enters DeepSx, the pin will retain the value it held prior to DeepSx entry. Driven High after PWROK rises. Based on wake events and ME state. SUSPWRDNACK is always `0' while in M0 or M3, but can be driven to 0 or 1 during the M-Off state. SUSPWRDNACK is the default mode of operation. If the system supports DeepSx, then subsequent boots will default to SUSWARN# mode. When Interface is in BUS IDLE, internal pull-down of 10k ohms is enabled. In normal transmission, a 400 ohm pull-down takes effect, the signal will be overridden to logic 1 with pull-up resistor (37 ohms) to 1.5 V. Depending on the platform usage, if termination is set to VSS then the signal is low. If it is terminated to VCC, the default value will be high. For AC coupling mode, DMI_TX* pins are terminated to VCC/2 and DMI_RX* pins are terminated to VSS. DMI AC coupling mode is only supported in Server/Workstation SKUs. OFF if DeepSx supported else not available (SUSPWRDNACK: Non-DeepSx OR DeepSx after RTC power failure) / Off (SUSWARN: DeepSx). The states of signals on Core and processor power planes are evaluated at the times during PLTRST# and immediately after PLTRST#. The states of the Controller Link signals are taken at the times during CL_RST# and Immediately after CL_RST#. The states of the Suspend signals are evaluated at the times during RSMRST# and Immediately after RSMRST#, with an exception to GPIO signals; refer to Section 2.17 for more details on GPIO state after reset. The states of the HDA signals are evaluated at the times During HDA_RST# and Immediately after HDA_RST#. Flexible I/O ports follow the properties of the selected technology. GPIO13 is located in the HDA Suspend well. It can only be used if VccsusHDA is powered. The internal pull-down on HDA_SYNC and HDA_SDO is enabled after reset. 101 PCH Pin States 3.3 Input and I/O Signals Planes and States Table 3-3 shows the power plane associated with the input and I/O signals, as well as the state at various times. Within the table, the following terms are used: Note: "IPU" Internal pull-up. "IPD" Internal pull-down. "T" Toggling or signal is transitioning because function not stopping. "High-Z" Tri-state. PCH not driving the signal high or low. "Defined" Driven to a level that is defined by the function or external pullup/pull-down resistor (will be high or low). "Off" The power plane is off; PCH is not driving when configured as an output or sampling when configured as an input. Pin state within table assumes interfaces are idle and default pin configuration for different power states. Signal levels are the same in S3, S4, and S5, except as noted. In general, PCH suspend well signal states are indeterminate and undefined and may glitch prior to RSMRST# de-assertion. PCH core well signal states are indeterminate and undefined and may glitch prior to PWROK assertion. However, this does not apply to THRMTRIP# as this signal is determinate and defined prior to PWROK assertion. DSW indicates PCH Deep Sx Well. This state provides a few wake events and critical context to allow system to draw minimal power in S3, S4, or S5 states. In general, PCH DSW signal states are indeterminate, undefined and may glitch prior to DPWROK assertion. The signals that are determinate and defined prior to DPWROK assertion will have a note added as a reference. ASW indicates PCH Active Sleep Well. This power well contains functionality associated with active usage models while the host system is in Sx. 102 Datasheet PCH Pin States Table 3-3. Input Signals - Power Plane and States in Desktop and Mobile Configurations (Sheet 1 of 4) Signal Name Power Plane During Reset Immediately after Reset S3/S4/S5 Deep Sx IPD IPD Off USB Interface USB2p/n[13:0] Suspend 17 IPD 1, 2 USB3Rp/n[4:3] , USB3Rp/ n[6:5, 2:1] Suspend IPD1, 2 IPD1, 2 S3 IPD S4 and S5 Off Off OC0#3, OC1#3, OC2#3, OC3#3, OC4#3, OC5#3, OC6#3, OC7#3 Suspend High-Z High-Z High-Z Off PCI Express* PERp/n[2:1]17 Suspend or Core6 IPD4 IPD4 Off Off PERp/n[8:3] Core IPD4 IPD4 Off Off SATA Interface Core IPD2 IPD2 Off Off Core IPD 2 IPD2 Off Off SATA0GP, SATA4GP, SATA5G Core High-Z High-Z Off Off SATA1GP Core IPU High-Z Off Off SATA2GP, SATA3GP Core IPD High-Z Off Off SATA_RXp/n[3:0] SATA_RXp/n[5:4] 17 Clocking Signals XTAL25_IN Core High-Z High-Z Off Off PEG_A_CLKRQ#, PEG_B_CLKRQ#, PCIECLKRQ0#, PCIECLKRQ3#, PCIECLKRQ4#, PCIECLKRQ5#, PCIECLKRQ6#, PCIECLKRQ7# Suspend High-Z High-Z High-Z Off PCIECLKRQ1#, PCIECLKRQ2# Core High-Z High-Z Off Off CLKIN_33MHZLOOPBACK Core High-Z High-Z Off Off DIFFCLK_BIASREF Core High-Z High-Z Off Off ICLK_IREF Core High-Z High-Z Off Off Processor Interface RCIN# Core High-Z High-Z Off Off THRMTRIP# Core High-Z High-Z Off Off Interrupt Interface SERIRQ Core High-Z High-Z Off Off PIRQ[D:A]# Core High-Z High-Z Off Off PIRQ[H:E]# Core High-Z High-Z Off Off IPD2, 18 Off Off DMI DMI_RXp/n[3:0] Datasheet Core IPD 2, 18 103 PCH Pin States Table 3-3. Input Signals - Power Plane and States in Desktop and Mobile Configurations (Sheet 2 of 4) Signal Name Power Plane During Reset Immediately after Reset S3/S4/S5 Deep Sx Off Off Intel(R) Flexible Display Interface (Intel(R) FDI) FDI_RXP/N[1:0] Core High-Z IPD2 Analog Display / VGA DAC Signals DAC_IREF Core High-Z DL Off Off VGA_DDC_CLK Core High-Z High-Z Off Off VGA_DDC_DATA Core High-Z High-Z Off Off VGA_IRTN Core High-Z High-Z Off Off Digital Display Interface DDPB_AUXP/N, DDPC_AUXP/N, DDPD_AUXP/N Core IPD IPD Off Off DDPB_CTRLCLK, DDPC_CTRLCLK, DDPD_CTRLCLK Core High-Z High-Z Off Off DDPB_CTRLDATA, DDPC_CTRLDATA, DDPD_CTRLDATA Core IPD5 High-Z Off Off DDPB_HPD, DDPC_HPD, DDPD_HPD Core High-Z High-Z Off Off eDP_VDD_EN Core DL DL Off Off eDP_BKLTEN Core DL DL Off Off eDP_BKLTCTL Core DL DL Off Off IPD IPD Off Intel(R) High Definition Audio Interface (Intel(R) HD Audio) HDA_SDI[3:0] Suspend IPD LPC Interface LAD[3:0] Core IPU IPU Off Off LDRQ0# LDRQ1# Core IPU IPU Off Off Non-Multiplexed GPIO Signals GPIO8 Suspend IPU DH DH Off GPIO15 Suspend DL DL DL Off GPIO24 Suspend DL DL DL Off DSW High-Z High-Z High-Z High-Z / IPD8 GPIO28 Suspend DL DL DL Off GPIO34 Core High-Z High-Z Off Off GPIO50 Core High-Z High-Z Off Off GPIO27 104 GPIO51 Core IPU DH Off Off GPIO52 Core High-Z High-Z Off Off GPIO53 Core IPU DH Off Off Datasheet PCH Pin States Table 3-3. Input Signals - Power Plane and States in Desktop and Mobile Configurations (Sheet 3 of 4) Signal Name Power Plane During Reset Immediately after Reset S3/S4/S5 Deep Sx GPIO54 Core High-Z High-Z Off Off GPIO55 Core IPU DL DL Off GPIO57 Suspend DL High-Z High-Z Off SMBus Interface SMBCLK, SMBDATA Suspend High-Z High-Z High-Z Off SMBALERT# Suspend High-Z High-Z High-Z Off System Management Interface INTRUDER# RTC High-Z High-Z High-Z High-Z SML0DATA Suspend High-Z High-Z High-Z Off SML0CLK Suspend High-Z High-Z High-Z Off SML1CLK Suspend High-Z High-Z High-Z Off SML1DATA Suspend High-Z High-Z High-Z Off Controller Link CL_CLK 9 CL_DATA9 Suspend Terminated10 Terminated10 IPD Off Suspend Terminated10 Terminated10 IPD Off DL DL Off SPI Interface SPI_MOSI ASW IPD SPI_MISO ASW IPU IPU IPU Off SPI_IO2 ASW IPU IPU IPU Off SPI_IO3 ASW IPU IPU IPU Off IPD / HighZ8 Power Management ACPRESENT 13 DSW DL (Non-DSx mode) High-Z (DSx mode) High-Z High-Z APWROK Suspend High-Z High-Z High-Z Off BATLOW# DSW IPU IPU IPU IPU/IP8 BMBUSY# Core High-Z High-Z Off Off DPWROK RTC High-Z High-Z High-Z High-Z PWRBTN# DSW IPU IPU IPU IPU PWROK RTC High-Z High-Z High-Z High-Z RI# Suspend High-Z High-Z High-Z Off RSMRST# RTC High-Z High-Z High-Z High-Z SUSACK# Suspend IPU IPU IPU Off SYS_PWROK Suspend High-Z High-Z High-Z Off SYS_RESET# Core High-Z High-Z Off Off High-Z High-Z / IPD8 WAKE# Datasheet DSW High-Z High-Z 105 PCH Pin States Table 3-3. Input Signals - Power Plane and States in Desktop and Mobile Configurations (Sheet 4 of 4) Signal Name Power Plane During Reset Immediately after Reset S3/S4/S5 Deep Sx Thermal Signals TACH0, TACH1, TACH2, TACH3, TACH4, TACH5, TACH6, TACH7 Core IPU (TACH) IPU(TACH) Off Off SST Suspend DL15 DL15 DL15 Off PECI Core DL16 DL16 Off Off TD_IREF Core Analog Analog Off Off High-Z High-Z High-Z Miscellaneous Signals INTVRMEN RTC High-Z DSWVRMEN RTC High-Z High-Z High-Z High-Z RTCRST# RTC High-Z High-Z High-Z High-Z SRTCRST# RTC High-Z High-Z High-Z High-Z PME# Suspend IPU IPU IPU Off JTAG_TCK Suspend IPD IPD IPD Off JTAG_TMS Suspend IPU IPU IPU Off JTAG_TDI Suspend IPU IPU IPU Off Note: 1. USB3 Rx pins transition from High-Z to IPD after Reset. 2. This is a strong pull-down (or pull-up, as applicable). 3. Signals must be shared between ports. There are only 8 OC# signals and 14 USB ports. 4. PCIe Rx pins transition from High-Z to IPD after Reset. 5. External 2.2 K Pull-Up when used - strap sampled during reset only. 6. The power well depends on whether the PCIe port is being multiplexed with USB3 (suspend) or with SATA (core). 7. This pin will be driven High when Dock Attach bit is set (Docking Control Register D27:F0 Offset 4Ch). 8. Pull-down is configurable; refer to DSX_CFG register (RCBA+3334h) for more details. 9. The state of signals in S3-S5 will be defined by Intel ME Policies. 10. The terminated state is when the I/O buffer pull-down is enabled. 11. N/A. 12. N/A. 13. The pin output shall not glitch during power up sequence. 14. N/A 15. When interface is in BUS IDLE status, internal pull-down of 10k ohms is enabled. In normal transmission, a 400 ohms pull-down takes effect, the signal will be overridden to logic 1 with pull-up resistor (37 ohms) to 1.5 V. 16. This is a 350 ohm normal pull-down, the signal will be overridden to logic 1 with pull-up resistor (31 ohms) to 1.05 V. 17. The Flexible I/O ports follow the properties of the selected technology. 18. Depending on the platform usage, if termination is set to VSS then the signal is low. If it is terminated to VCC, the default value will be high. For AC coupling mode, DMI_TX* pins are terminated to VCC/2 and DMI_RX* pins are terminated to VSS. DMI AC coupling mode is only supported in Server/Workstation SKUs. Desktop and Mobile SKUs only support DC coupled mode, where the RX signals are terminated to VSS. 106 Datasheet PCH and System Clocks 4 PCH and System Clocks The PCH provides a complete system clocking solution through Integrated Clocking. PCH-based platforms require several single-ended and differential clocks to synchronize signal operation and data propagation between system-wide interfaces, and across clock domains. In Integrated Clock mode, all the system clocks will be provided by PCH from a 25 MHz crystal-generated clock input. The output signals from PCH are: * One 100 MHz differential source for BCLK and DMI (PCI Express* 3.0 jitter tolerant) * Two 135 MHz differential sources for DisplayPort* on Integrated Graphics processors * Eight 100 MHz differential sources for PCI Express 2.0 devices * Two 100 MHz differential source for PCI Express Graphics devices (PCI Express 3.0 jitter tolerant) * One 100 MHz differential clock for XDP/ITP which can be used as a clock to a 3rd PEG slot (PCI Express 3.0 jitter tolerant) * Five 33 MHz single-ended source for other devices (One of these is reserved as loopback clock) * Four flexible single-ended outputs that can be used for 14.31818/24/33/48 MHz for legacy platform functions, discrete graphics devices, external USB controllers, and so on. 4.1 Straps Related to Clock Configuration Hardware functional straps (that is, pins): None required for clock configuration. Soft straps implemented in the SPI flash device for PCH clock configuration: Integrated Clocking Profile Select (3 Profile select bits allow up to 8 different clock profiles to be specified). In addition, 3 RTC well backed host register bits are also defined for Integrated Clocking Profile Selection through BIOS. 4.2 Platform Clocking Requirements Providing a platform-level clocking solution uses multiple system components including: * The PCH * 25 MHz crystal source More detail on the clock interface signals is provided in Section 2.5 but a summary is given in the following tables; Table 4-1 shows the system clock input to PCH. Table 4-2 shows system clock outputs generated by PCH. Table 4-1. PCH Clock Inputs (Sheet 1 of 2) Clock Domain CLKIN_DMI_P/N CLKIN_DOT96_P/N CLKIN_SATA_P/N Datasheet Frequency Usage description 100 MHz Unused. Tie each signal to GND through a 10 Kresistor. 96 MHz Unused. Tie each signal to GND through a 10 Kresistor. 100 MHz Unused. Tie each signal to GND through a 10 Kresistor. 107 PCH and System Clocks Table 4-1. PCH Clock Inputs (Sheet 2 of 2) Clock Domain CLKIN_GND_P/N CLKIN_33MHZLOOPBACK Usage description 100 MHz Unused. Tie each signal to GND through a 10 Kresistor. 33 MHz 14.31818 MHz REFCLK14IN 25 MHz XTAL25_IN Table 4-2. Frequency 33 MHz clock feedBack input to reduce skew between PCH 33 MHz clocks and buses such as LPC. This signal must be connected to one of the pins in the group CLKOUT_33MHz[4:0] Unused. Tie signal to GND through a 10 Kresistor. Crystal input source used by PCH. Clock Outputs Clock Domain Frequency Spread Spectrum Usage 33 MHz Yes Single Ended 33 MHz outputs. One of these signals must be connected to CLKIN_33MHZLOOPBACK to function as a clock loopback. This allows skew control for variable lengths of CLKOUT_33MHz[4:0]. CLKOUT_DMI_P/N 100 MHz Yes 100 MHz PCIe* 3.0 specification compliant differential output to the processor for DMI/BCLK. CLKOUT_PCIE[7:0]_P/N 100 MHz Yes 100 MHz PCIe 2.0 specification compliant differential output to PCI Express devices. 100 MHz Yes 100 MHz PCIe 3.0 specification compliant differential outputs to PCI Express Graphics devices. 100 MHz Yes Primarily used as 100 MHz Clock to processor XDP/ITP on the platform or can be configured as CLKOUT_PEG_C_P/N. 135 MHz Yes 135 MHz Differential SSC capable outputs to processor for DisplayPort. CLKOUT_33MHz[4:0] CLKOUT_PEG_A_P/N CLKOUT_PEG_B_P/N CLKOUT_ITPXDP_P/N CLKOUT_DP_P/N 135 MHz Differential non-SSC capable outputs to processor for DisplayPort. CLKOUT_DPNS_P/N 135 MHz No Note: CLKOUT_DPNS_P/N must always be connected, regardless of internal graphics application support. Programmable 33 MHz, 48/24 MHz or 14.31818 MHz outputs for various platform devices. CLKOUTFLEX0/ CLKOUTFLEX1/ CLKOUTFLEX2/ CLKOUTFLEX3/ SPI_CLK 108 GPIO64 GPIO65 GPIO66 GPIO67 Note: 33 MHz / 14.31818 MHz / 48 MHz / 24 MHz Yes 17.86 MHz / 31.25 MHz / 50 MHz No It is highly recommended to prioritize 14.31818/24/48 MHz clocks on CLKOUTFLEX1 and CLKOUTFLEX3 outputs. Intel does not recommend configuring the 14.31818/24/48 MHz clocks on CLKOUTFLEX0 and CLKOUTFLEX2 if more than two 33 MHz clocks in addition to the feedback clock are used on the CLKOUT_33 MHz outputs. Drive SPI devices connected to the PCH. Generated by the PCH. Datasheet PCH and System Clocks 4.3 Functional Blocks The PCH has 1 main PLL in which its output is divided down through Modulators and Dividers to provide great flexibility in clock source selection, configuration, and better power management. Table 4-3 describes the PLLs on the PCH and the clock domains that are driven from the PLLs. Table 4-3. PCH PLLs Outputs1 Description/Usage Four 2.7 GHz outputs 90 apart. Outputs are routed to each of the Spread Modulator blocks before hitting the various dividers and the other PLLs to provide clocks to all of the I/O interface logic. This PLL also provides 5.4 GHz and 2.7 GHz CMOS outputs for use by various dividers to create non-spread output clocks. Main Reference PLL. Always enabled in Integrated Clocking mode. Resides in core power well and is not powered in S3 and below states. Powered in subS0 states by a Suspend well Ring oscillator. PLL XCK_PLL Notes: 1. Indicates the source clock frequencies driven to other internal logic for delivering functionality needed. Does not indicate external outputs. Spread Spectrum adjustment can be made without platform reboot. Table 4-4 provides a basic description of spread modulators that operate on the XCK PLL's 2.7 GHz outputs. Table 4-4. Datasheet Modulator Blocks Modulator Description MOD1 Used for spread modulation, or bending, on 135 MHz clock to integrated graphics display. Typical display usage model is 0.5% down-spread. In certain usage case, this modulator can be shut off for 0% spread with or without clock bending. Used by the display driver only. MOD2 Used for spread modulation and fine grain frequency synthesis on nominal 100 MHz overclockable clock to CPU BCLK (CLKOUT_DMI), DMI, PEG. This modulator also subject to adaptive clocking adjustment (for EMC) when left on at nominal 100 MHz frequency. MOD3 Used for spread modulation (and adaptive clocking) on 100 M Hz clock to processor BCLK (CLKOUT_DMI), DMI, PEG, PCIe*, USB 3.0, SATA, Single Ended 33 MHz, and Thermal Sensor. MOD4 Used for fine grain frequency synthesis on nominal 135 MHz, non-spread clock to integrated graphics display. Used by the display driver only. MOD5 Used for fine grain frequency synthesis of a wide variety of integrated graphics display VGA clocking needs. Used by the display driver only. MOD6 Used for fine grain frequency synthesis of 96 MHz non-spread clock to USB PLL and PCH logic. 48/24 MHz to Flex Clocks are further derived from 96 MHz output. MOD7 Used for fine grain frequency synthesis of 14.31818 MHz non-spread clock to Flex Clocks and PCH logic. 109 PCH and System Clocks Figure 4-1. PCH Detailed Clock Diagram Control through display register set PLLRCS[14:13] 00 - MODIV3 (POR) 01 - MODIV2 FDI_PLL DMI PORT DMI_PLL (OC Use) MODIV1 (135MHz) USB3PCIe_PLL (Non OC Use) MCSS [2] 00 - USB3PCIe_PLL (POR) 01 - DMI_PLL CLKOUT_DP_P/N (To Processor) MODIV4 (135MHz) MODIV5 (Various Freq) VGA_Display PLLs PMSync MCSS [1] 0 - USB3PCIe_PLL (POR) 1 - DMI_PLL x2 XCK_PLL / VCO MODIV2 (100MHz) CLKOUT_PEG_[B:A]_P/N CLKOUT_DMI_P/N (To Processor) CLKOUT_ITPXDP_P/N CLKOUT_PCIE_[7:0]_P/N MODIV3 (100MHz) SATA_PLL PCH Legacy. This must be Free Running Divide by 81 (Non-Spread) CLKOUT_33MHz [4:0] DIV_PCI33[22:21] 00 - Spread (POR) 11 - Non-Spread DIV4824 (48/ 24 MHz) DIV_FLEX4824[10:8] 001 - 48MHz (POR) 101 - 24MHz MODIV7 (14.31818MHz) FFDIVME (385.71MHz) CLKIN_33MHZ LOOPBACK * requires one clock copy only USB2_PLL MODIV6 (96Mhz) 110 DCOSS [7:6] PEGB DCOSS [5:4] PEGA 00 - MODIV3 (POR) 01 - MODIV2 10 - DMI_PLL DCOSS [9:8] 00 - MODIV3 (POR) 01 - MODIV2 Divide by 3 (Spread) 25MHz XTAL CLKOUT_DPNS_P/N (To Processor) ME Core x4 CLKOUT_FLEX[3:0] SECOSS [14:12] - CLKOUTFLEX3 SECOSS [10:8] - CLKOUTFLEX2 SECOSS [6:4] - CLKOUTFLEX1 SECOSS [2:0] - CLKOUTFLEX0 000 - 33.33MHz Clock Source 001 - 14.31818MHz Clock Source (default for Flex 1) 010 - 48/24MHz Clock Source (default for Flex 3) 101 - Reserved (default for Flex 0 and Flex 2) IMPORTANT: 1. Non-POR configurations have not been fully validated by Intel and may be shown only as an example . 2. Overclocking / Center Spread mode places the platform in an unsupported configuration and /or operational state and can result in platform instability, physical damage, and data loss. These margins are not guaranteed or supported. 3. MODIV2 Clock source is not electrically validated (EV). Example; compliance to PCIe clock jitter, Transmitter jitter performance, etc. 4. MODIV1, MODIV4 and MODIV5 programming is done through the Integrated Graphic Display MMIO register set . 5. CLKOUT_FLEX[3:2] must be programmed to the same clock source for proper operation. For example if both CLKOUT_FLEX[3:2] are to be enabled and 33MHz is desired on one clock, BOTH clocks have to be programmed for that same frequency and cannot be programmed to one having a different frequency than the other. Datasheet PCH and System Clocks 4.4 Clock Configuration Access Overview The PCH provides increased flexibility of host equivalent configurability of clocks, using Intel ME FW. In the Intel ME FW assisted configuration mode, control settings for PLLs, Spread Modulators, and other clock configuration registers will be handled by the Intel ME. The parameters to be loaded will reside in the Intel ME data region of the SPI Flash device. BIOS would only have access to the register set through a set of Intel MEI commands to the Intel ME. Datasheet 111 Functional Description 5 Functional Description This chapter describes the functions and interfaces of the PCH. 5.1 Flexible I/O The PCH implements Flexible I/O, an architecture to allow some high speed signals to be configured as PCIe*, USB 3.0 or SATA signals in accordance with I/O needs on a platform. There are 18 differential pairs that are split between the three interfaces. Among them, 4 differential pairs are multiplexed: 2 multiplexed differential pairs can be configured to be used as PCIe port 1, 2 or USB3 port 3, 4, and the other 2 differential pairs can be configured to be used as PCIe port 1, 2 or SATA port 4, 5. Figure 5-1 below illustrates how the signals are utilized for Flexible I/O. The Flexible I/O is configured through soft straps. Refer to the latest PCH SPI Programming Guide Application Note for more detail on the soft strap. These Flexible I/O ports can be configured in any way as allowed by the soft strap, provided that the max number of PCIe ports does not exceed 8. Note: Specifically for the multiplexed differential signal pairs between SATA and PCIe, the corresponding soft straps provide an option to select desired ports using GPIO16 and GPIO49. If a GPIO is chosen to select the desired port, the GPIO value needs to be valid at PLTRST# de-assertion and must be maintained without change while PCH_PLTRST# remains de-asserted. Figure 5-1. Flexible I/O - High Speed Signal Mapping with PCI Express*, USB 3.0*, and SATA Ports Notes: 1. USB3Tp3/USB3Tn3 and USB3Rp3/USB3Rn3 signals are multiplexed with PETp1/PETn1 and PERp1/PERn1 signals respectively. 2. USB3Tp4/USB3Tn4 and USB3Rp4/USB3Rn4 signals are multiplexed with PETp2/PETn2 and PERp2/PERn2 signals respectively. 3. SATA_TXP4/SATA_TXN4 and SATA_RXP4/SATA_RXN4 signals are multiplexed with PETp1/PETn1 and PERp1/PERn1 signals respectively. 4. SATA_TXP5/SATA_TXN5 and SATA_RXP5/SATA_RXN5 signals are multiplexed with PETp2/PETn2 and PERp2/PERn2 signals respectively. 5. The total number of PCIe ports on the platform must not exceed 8. The system designer needs to take this into account when configuring the flexible I/O on the platform. 112 Datasheet Functional Description 5.2 PCI-to-PCI Bridge The PCI-to-PCI bridge resides in PCI. This portion of the PCH implements the buffering and control logic between PCI and Direct Media Interface (DMI). The arbitration for the PCI bus is handled by this PCI device. The PCI decoder in this device must decode the ranges for the DMI. All register contents are lost when core well power is removed. Direct Media Interface (DMI) is the chip-to-chip connection between the processor and the PCH. This high-speed interface integrates advanced priority-based servicing allowing for concurrent traffic and true isochronous transfer capabilities. Base functionality is completely software transparent permitting current and legacy software to operate normally. To provide for true isochronous transfers and configurable Quality of Service (QoS) transactions, the PCH supports two virtual channels on DMI--VC0 and VC1. These two channels provide a fixed arbitration scheme where VC1 is always the highest priority. VC0 is the default conduit of traffic for DMI and is always enabled. VC1 must be specifically enabled and configured at both ends of the DMI link (that is, the PCH and processor). Configuration registers for DMI, virtual channel support, and DMI active state power management (ASPM) are in the RCRB space in the Chipset Config Registers (Chapter 10). DMI is also capable of operating in an Enterprise Southbridge Interface (ESI) compatible mode. ESI is a chip-to-chip connection for server/workstation chipsets. In this ESI-compatible mode, the DMI signals require AC coupling. A hardware strap is used to configure DMI in ESI-compatible mode see Section 2.26 for details. 5.2.1 PCI Bus Interface The PCI Bus Interface is not available on any PCH SKU. 5.2.2 PCI Legacy Mode PCI functionality is not supported on new generation of PCH requiring methods such as using PCIe*-to-PCI bridges to enable external PCI I/O devices. To be able to use PCIeto-PCI bridges and attached legacy PCI devices, the PCH provides PCI Legacy Mode. PCI Legacy Mode allows both the PCI Express* root port and PCIe-to-PCI bridge look like subtractive PCI-to-PCI bridges. This allows the PCI Express root port to subtractively decode and forward legacy cycles to the bridge, and the PCIe-to-PCI bridge continues forwarding legacy cycles to downstream PCI devices. Software must ensure that only one PCH device is enabled for Subtractive decode at a time. 5.3 PCI Express* Root Ports (D28:F0~F7) There are eight root ports available in the PCH. The root ports are compliant to the PCI Express 2.0 specification running at 5.0 GT/s. The ports all reside in Device 28, and take Function 0 - 7. Port 1 is Function 0, Port 2 is Function 1, Port 3 is Function 2, Port 4 is Function 3, Port 5 is Function 4, Port 6 is Function 5, Port 7 is Function 6, and Port 8 is Function 7. Note: Datasheet This section assumes the default PCI Express Function Number-to-Root Port mapping is used. Function numbers for a given root port are assignable through the Root Port 113 Functional Description Function Number and Hide for PCI Express Root Ports register (RCBA+404h). In accordance with the PCI Local Bus Specification, all multi-function devices must have a Function 0 assigned. Note: Non-Common Clock Mode operation is not supported on all PCI Express root ports. 5.3.1 Supported PCI Express* (PCIe*) Port Configurations PCI Express Root Ports 1-4 or Ports 5-8 can independently be configured as four x1s, two x2s, one x2 and two x1s, or one x4 port widths, as shown in Table 5-1 and Table 5-2. Function disable is covered in Section 10.1.51. Table 5-1. PCI Express* Ports 1 thru 4 - Supported Configurations Port 1 Port 2 Port 3 Port 4 x4 x2 x2 x2 x1 Table 5-2. x1 x1 x1 x1 x1 PCI Express* Ports 5 thru 8 - Supported Configurations Port 5 Port 6 Port 7 Port 8 x4 x2 x2 x2 x1 5.3.2 x1 x1 x1 x1 x1 Interrupt Generation The root port generates interrupts on behalf of Hot-Plug and power management events, when enabled. These interrupts can either be pin based, or can be MSIs, when enabled. When an interrupt is generated using the legacy pin, the pin is internally routed to the PCH interrupt controllers. The pin that is driven is based upon the setting of the chipset configuration registers. Specifically, the chipset configuration registers used are the D28IP (Base address + 310Ch) and D28IR (Base address + 3146h) registers. Table 5-3 summarizes interrupt behavior for MSI and wire-modes. In the table "bits" refers to the Hot-Plug and PME interrupt bits. Table 5-3. MSI versus PCI IRQ Actions Interrupt Register All bits 0 MSI Action Wire inactive No action One or more bits set to 1 Wire active Send message One or more bits set to 1, new bit gets set to 1 Wire active Send message One or more bits set to 1, software clears some (but not all) bits Wire active Send message One or more bits set to 1, software clears all bits Software clears one or more bits, and one or more bits are set on the same clock 114 Wire-Mode Action Wire inactive No action Wire active Send message Datasheet Functional Description 5.3.3 Power Management 5.3.3.1 S3/S4/S5 Support Software initiates the transition to S3/S4/S5 by performing an I/O write to the Power Management Control register in the PCH. After the I/O write completion has been returned to the processor, each root port will send a PME_Turn_Off TLP (Transaction Layer Packet) message on its downstream link. The device attached to the link will eventually respond with a PME_TO_Ack TLP message followed by sending a PM_Enter_L23 DLLP (Data Link Layer Packet) request to enter the L2/L3 Ready state. When all of the PCH root ports links are in the L2/L3 Ready state, the PCH power management control logic will proceed with the entry into S3/S4/S5. Prior to entering S3, software is required to put each device into D3HOT. When a device is put into D3HOT, it will initiate entry into a L1 link state by sending a PM_Enter_L1 DLLP. Thus, under normal operating conditions when the root ports sends the PME_Turn_Off message, the link will be in state L1. However, when the root port is instructed to send the PME_Turn_Off message, it will send it whether or not the link was in L1. Endpoints attached to PCH can make no assumptions about the state of the link prior to receiving a PME_Turn_Off message. 5.3.3.2 Resuming from Suspended State The root port contains enough circuitry in the suspend well to detect a wake event through the WAKE# signal and to wake the system. When WAKE# is detected asserted, an internal signal is sent to the power management controller of the PCH to cause the system to wake up. This internal message is not logged in any register, nor is an interrupt/GPE generated due to it. 5.3.3.3 Device Initiated PM_PME Message When the system has returned to a working state from a previous low power state, a device requesting service will send a PM_PME message continuously, until acknowledged by the root port. The root port will take different actions depending upon whether this is the first PM_PME that has been received, or whether a previous message has been received but not yet serviced by the operating system. If this is the first message received (RSTS.PS - D28:F0/F1/F2/F3/F4/F5/F6/F7:Offset 60h:bit 16 is cleared), the root port will set RSTS.PS, and log the PME Requester ID into RSTS.RID (D28:F0/F1/F2/F3/F4/F5/F6/F7:Offset 60h:bits 15:0). If an interrupt is enabled using RCTL.PIE (D28:F0/F1/F2/F3/F4/F5/F6/F7:Offset 5Ch:bit 3), an interrupt will be generated. This interrupt can be either a pin or an MSI if MSI is enabled using MC.MSIE (D28:F0/F1/F2/F3/F4/F5/F6/F7:Offset 82h:Bit 0). See Section 5.3.3.4 for SMI/SCI generation. If this is a subsequent message received (RSTS.PS is already set), the root port will set RSTS.PP (D28:F0/F1/F2/F3/F4/F5/F6/F7:Offset 60h:Bit 17) and log the PME Requester ID from the message in a hidden register. No other action will be taken. When the first PME event is cleared by software clearing RSTS.PS, the root port will set RSTS.PS, clear RSTS.PP, and move the requester ID from the hidden register into RSTS.RID. Datasheet 115 Functional Description If RCTL.PIE is set, an interrupt will be generated. If RCTL.PIE is not set, a message will be sent to the power management controller so that a GPE can be set. If messages have been logged (RSTS.PS is set), and RCTL.PIE is later written from a 0 to a 1, an interrupt will be generated. This last condition handles the case where the message was received prior to the operating system re-enabling interrupts after resuming from a low power state. 5.3.3.4 SMI/SCI Generation Interrupts for power management events are not supported on legacy operating systems. To support power management on non-PCI Express aware operating systems, PM events can be routed to generate SCI. To generate SCI, MPC.PMCE must be set. When set, a power management event will cause SMSCS.PMCS (D28:F0/F1/F2/F3/F4/ F5/F6/F7:Offset DCh:Bit 31) to be set. Additionally, BIOS workarounds for power management can be supported by setting MPC.PMME (D28:F0/F1/F2/F3/F4/F5/F6/F7:Offset D8h:Bit 0). When this bit is set, power management events will set SMSCS.PMMS (D28:F0/F1/F2/F3/F4/F5/F6/ F7:Offset DCh:Bit 0), and SMI # will be generated. This bit will be set regardless of whether interrupts or SCI is enabled. The SMI# may occur concurrently with an interrupt or SCI. 5.3.3.5 Latency Tolerance Reporting (LTR) The root port supports the extended Latency Tolerance Reporting (LTR) capability. LTR provides a means for device endpoints to dynamically report their service latency requirements for memory access to the root port. Endpoint devices should transmit a new LTR message to the root port each time its latency tolerance changes (and initially during boot). The PCH uses the information to make better power management decision. The processor uses the worst case tolerance value communicated by the PCH to optimize c-state transitions. This results in better platform power management without impacting endpoint functionality. Note: Endpoint devices the support LTR must implement the reporting and enable mechanism detailed in the PCIe* Latency Tolerance Reporting Engineering Change Notice. 5.3.3.6 Opportunistic Buffer Flush/Fill (OBFF) The Opportunistic Buffer Flush/Fill (OBFF) capability (also known as Optimized Buffer Flush/Fill) feature has been dropped from POR in the Intel Series 8 PCH Family and is no longer supported. 5.3.4 SERR# Generation SERR# may be generated using two paths - through PCI mechanisms involving bits in the PCI header, or through PCI Express* mechanisms involving bits in the PCI Express capability structure. 116 Datasheet Functional Description Figure 5-2. Generation of SERR# to Platform 5.3.5 Hot-Plug All PCIe* Root Ports support Express Card 1.0 based hotplug that performs the following: * Presence Detect and Link Active Changed Support * Interrupt generation 5.3.5.1 Presence Detection When a module is plugged in and power is supplied, the physical layer will detect the presence of the device, and the root port sets SLSTS.PDS (D28:F0/F1/F2/F3/F4/ F5:Offset 5Ah:Bit 6) and SLSTS.PDC (D28:F0/F1/F2/F3:Offset 6h:Bit 3). If SLCTL.PDE (D28:F0/F1/F2/F3/F4/F5/F6/F7:Offset 58h:Bit 3) and SLCTL.HPE (D28:F0/F1/F2/F3/ F4/F5/F6/F7:Offset 58h:Bit 5) are both set, the root port will also generate an interrupt. When a module is removed (using the physical layer detection), the root port clears SLSTS.PDS and sets SLSTS.PDC. If SLCTL.PDE and SLCTL.HPE are both set, the root port will also generate an interrupt. 5.3.5.2 SMI/SCI Generation Interrupts for Hot-Plug events are not supported on legacy operating systems. To support Hot-Plug on n on-PCI Express aware operating systems, Hot-Plug events can be routed to generate SCI. To generate SCI, MPC.HPCE (D28:F0/F1/F2/F3/F4/F5/F6/ F7:Offset D8h:Bit 30) must be set. When set, enabled Hot-Plug events will cause SMSCS.HPCS (D28:F0/F1/F2/F3/F4/F5/F6/F7:Offset DCh:Bit 30) to be set. Additionally, BIOS workarounds for Hot-Plug can be supported by setting MPC.HPME (D28:F0/F1/F2/F3/F4/F5/F6/F7:Offset D8h:Bit 1). When this bit is set, Hot-Plug events can cause SMI status bits in SMSCS to be set. Supported Hot-Plug events and their corresponding SMSCS bit are: * Presence Detect Changed - SMSCS.HPPDM (D28:F0/F1/F2/F3/F4/F5/F6/F7:Offset DCh:Bit 1) * Link Active State Changed - SMSCS.HPLAS (D28:F0/F1/F2/F3/F4/F5/F6/F7:Offset DCh:Bit 4) Datasheet 117 Functional Description When any of these bits are set, SMI# will be generated. These bits are set regardless of whether interrupts or SCI is enabled for Hot-Plug events. The SMI# may occur concurrently with an interrupt or SCI. 5.4 Gigabit Ethernet Controller (B0:D25:F0) The PCH integrates a Gigabit Ethernet (GbE) controller. The integrated GbE controller is compatible with the Intel(R) Ethernet Network Connection I127LM/V Platform LAN Connect device. The integrated GbE controller provides two interfaces for 10/100/ 1000 Mb/s and manageability operation: * Based on PCI Express* - A high-speed SerDes interface using PCI Express electrical signaling at half speed while keeping the custom logical protocol for active state operation mode. * System Management Bus (SMBus) SMLink0 - A low speed connection for low power state mode for manageability communication only. The frequency of this connection can be configured to one of three different speeds (100KHz, 400KHz or 1MHz). At this low power state mode the Ethernet link speed is reduced to 10 Mb/s. Note: The SMBus Specification Version 2.0 defines a maximum bus frequency of 100 kHz. Speeds faster than this are not SMBus compliant and are used by Intel to support higher bandwidth manageability communication in the Sx states. The Intel Ethernet Network Connection I127LM/V Platform LAN Connect Device can be connected to any non-multiplexed (fixed) PCI Express port or the Flexible I/O PCI Express ports multiplexed with USB 3.0 on the PCH.The Intel Ethernet Network Connection I127LM/V Platform LAN Connect Device cannot be connected to the PCI Express Flexible I/O ports multiplexed with SATA. Figure 5-3. Valid PCI Express* Ports for Platform LAN Connect Device (GbE) Support The Intel Ethernet Network Connection I127LM/V only runs at a speed of 1250 Mb/s, which is 1/2 of the 2.5 Gb/s PCI Express* frequency. Each of the fixed signal PCI Express root ports and the Flex I/O PCI Express ports multiplexed with USB 3.0 in the PCH have the ability to run at the 1250 Mb/s rate. There is no need to implement a mechanism to detect that the Platform LAN Device is connected. The port configuration (if any), attached to the Platform LAN Device, is pre-loaded from the NVM. The selected port adjusts the transmitter to run at the 1250 Mb/s rate and does not need to be PCI Express compliant. 118 Datasheet Functional Description Note: PCIe validation tools cannot be used for electrical validation of this interface; however, PCIe layout rules apply for on-board routing. The integrated GbE controller operates at full-duplex at all supported speeds or halfduplex at 10/100 Mb/s. It also adheres to the IEEE 802.3x Flow Control Specification. Note: GbE operation (1000 Mb/s) is only supported in S0 mode. In Sx modes, SMBus is the only active bus and is used to support manageability/remote wake-up functionality. The integrated GbE controller provides a system interface using a PCI Express function. A full memory-mapped or I/O-mapped interface is provided to the software, along with DMA mechanisms for high performance data transfer. The integrated GbE controller features are: * Network Features -- Compliant with the 1 Gb/s Ethernet 802.3, 802.3u, 802.3z, 802.3ab specifications -- Multi-speed operation: 10/100/1000 Mb/s -- Full-duplex operation at 10/100/1000 Mb/s: Half-duplex at 10/100 Mb/s -- Flow control support compliant with the 802.3X specification as well as the specific operation of asymmetrical flow control defined by 802.3z -- VLAN support compliant with the 802.3q specification -- MAC address filters: perfect match unicast filters; multicast hash filtering, broadcast filter and promiscuous mode -- PCI Express/SMBus interface to GbE PHYs * Host Interface Features -- 64-bit address master support for systems using more than 4 GB of physical memory -- Programmable host memory receive buffers (256 Bytes to 16 KB) -- Intelligent interrupt generation features to enhance driver performance -- Descriptor ring management hardware for transmit and receive -- Software controlled reset (resets everything except the configuration space) -- Message Signaled Interrupts * Performance Features -- Configurable receive and transmit data FIFO, programmable in 1 KB increments -- TCP segmentation capability compatible with Windows NT* 5.x off-loading features -- Fragmented UDP checksum off-load for packet reassembly -- IPv4 and IPv6 checksum off-load support (receive, transmit, and TCP segmentation off-load) -- Split header support to eliminate payload copy from user space to host space -- Receive Side Scaling (RSS) with two hardware receive queues -- Supports 9018 bytes of jumbo packets -- Packet buffer size -- LinkSec off-load compliant with 802.3ae specification -- TimeSync off-load compliant with 802.1as specification * Virtualization Technology Features -- Warm function reset - function level reset (FLR) -- VMDq1 * Power Management Features -- Magic Packet* wake-up enable with unique MAC address Datasheet 119 Functional Description -- -- -- -- -- -- -- -- 5.4.1 ACPI register set and power down functionality supporting D0 and D3 states Full wake up support (APM, ACPI) MAC power down at Sx, DMoff with and without WoL Auto connect battery saver at S0 no link and Sx no link Energy Efficient Ethernet (EEE) support Latency Tolerance Reporting (LTR) ARP and ND proxy support through LAN Connected Device proxy Wake on LAN (WoL) from Deep Sx GbE PCI Express* Bus Interface The GbE controller has a PCI Express interface to the host processor and host memory. The following sections detail the bus transactions. 5.4.1.1 Transaction Layer The upper layer of the host architecture is the transaction layer. The transaction layer connects to the device GbE controller using an implementation specific protocol. Through this GbE controller-to-transaction-layer protocol, the application-specific parts of the device interact with the subsystem and transmit and receive requests to or from the remote agent, respectively. 5.4.1.2 Data Alignment 5.4.1.2.1 4-KB Boundary PCI requests must never specify an address/length combination that causes a memory space access to cross a 4 KB boundary. It is hardware's responsibility to break requests into 4 KB-aligned requests (if needed). This does not pose any requirement on software. However, if software allocates a buffer across a 4-KB boundary, hardware issues multiple requests for the buffer. Software should consider aligning buffers to a 4-KB boundary in cases where it improves performance. The alignment to the 4-KB boundaries is done by the GbE controller. The transaction layer does not do any alignment according to these boundaries. 5.4.1.2.2 64 Bytes PCI requests are 128 bytes or less and are aligned to make better use of memory controller resources. Writes, however, can be on any boundary and can cross a 64-byte alignment boundary. 5.4.1.3 Configuration Request Retry Status The integrated GbE controller might have a delay in initialization due to an NVM read. If the NVM configuration read operation is not completed and the device receives a configuration request, the device responds with a configuration request retry completion status to terminate the request, and thus effectively stalls the configuration request until such time that the sub-system has completed local initialization and is ready to communicate with the host. 120 Datasheet Functional Description 5.4.2 Error Events and Error Reporting 5.4.2.1 Data Parity Error The PCI host bus does not provide parity protection, but it does forward parity errors from bridges. The integrated GbE controller recognizes parity errors through the internal bus interface and sets the Parity Error bit in PCI configuration space. If parity errors are enabled in configuration space, a system error is indicated on the PCI host bus. The offending cycle with a parity error is dropped and not processed by the integrated GbE controller. 5.4.2.2 Completion with Unsuccessful Completion Status A completion with unsuccessful completion status (any status other than 000) is dropped and not processed by the integrated GbE controller. Furthermore, the request that corresponds to the unsuccessful completion is not retried. When this unsuccessful completion status is received, the System Error bit in the PCI configuration space is set. If the system errors are enabled in configuration space, a system error is indicated on the PCI host bus. 5.4.3 Ethernet Interface The integrated GbE controller provides a complete CSMA/CD function supporting IEEE 802.3 (10 Mb/s), 802.3u (100 Mb/s) implementations. It also supports the IEEE 802.3z and 802.3ab (1000 Mb/s) implementations. The device performs all of the functions required for transmission, reception, and collision handling called out in the standards. The mode used to communicate between the PCH and the Intel(R) Ethernet Network Connection I127LM/V Platform LAN Connect Device supports 10/100/1000 Mb/s operation, with both half- and full-duplex operation at 10/100 Mb/s, and full-duplex operation at 1000 Mb/s. 5.4.3.1 Intel(R) Ethernet Network Connection I127LM/V Platform LAN Connect Device Interface The integrated GbE controller and the Intel(R) Ethernet Network Connection I127LM/V Platform LAN Connect Device communicate through the PCIe and SMLink0 interfaces. All integrated GbE controller configuration is performed using device control registers mapped into system memory or I/O space. The Platform LAN Connect Device is configured using the PCI Express* or SMBus interface. The integrated GbE controller supports various modes as listed in Table 5-4. Table 5-4. LAN Mode Support Mode System State Interface Active Connections Normal 10/100/1000 Mb/s S0 PCI Express or Intel(R) Ethernet Network Connection I127LM/V Manageability and Remote Wake-up Sx SMLink0 Intel(R) Ethernet Network Connection I127LM/V SMLink01 Notes: 1. GbE operation is not supported in Sx states. Datasheet 121 Functional Description 5.4.4 PCI Power Management The integrated GbE controller supports the Advanced Configuration and Power Interface (ACPI) specification as well as Advanced Power Management (APM). This enables the network-related activity (using an internal host wake signal) to wake up the host. For example, from Sx (S3-S5) and Deep Sx to S0. Note: The Intel Ethernet Network Connection I127LM/V Platform LAN Connect Device must be powered during the Deep Sx state in order to support host wake up from Deep Sx. GPIO27 on the PCH must be configured to support wake from Deep Sx and must be connected to LANWAKE_N on the Platform LAN Connect Device. The SLP_LAN# signal must be driven high (de-asserted) in the Deep Sx state to maintain power to the Platform LAN Connect Device. The integrated GbE controller contains power management registers for PCI and supports D0 and D3 states. PCIe* transactions are only allowed in the D0 state, except for host accesses to the integrated GbE controller's PCI configuration registers. 5.4.4.1 Wake Up The integrated GbE controller supports two types of wake-up mechanisms: 1. Advanced Power Management (APM) Wake Up 2. ACPI Power Management Wake Up Both mechanisms use an internal logic signal to wake the system up. The wake-up steps are as follows: 1. Host wake event occurs (packet is not delivered to host). 2. The Platform LAN Connect Device receives a WoL packet/link status change. 3. The Platform LAN Connect Device sends a wake indication to the PCH (this requires the LANWAKE_N pin from the Intel(R) Ethernet Network Connection I127LM/V Platform LAN Connect Device to be connected to the PCH GPIO27 pin. GPIO27 must also be configured to support wake from Deep Sx. 4. If the system is in Deep Sx the wake will cause the system to wake from the Deep Sx state to the Sx state. 5. The Platform LAN Connect Device wakes up the integrated GbE controller using an SMBus message on SMLink0. 6. The integrated GbE controller sets the PME_STATUS bit. 7. System wakes from Sx state to S0 state. 8. The host LAN function is transitioned to D0. 9. The host clears the PME_STATUS bit. 5.4.4.1.1 Advanced Power Management Wake Up Advanced Power Management Wake Up or APM Wake Up was previously known as Wake on LAN (WoL). It is a feature that has existed in the 10/100 Mb/s NICs for several generations. The basic premise is to receive a broadcast or unicast packet with an explicit data pattern and then to assert a signal to wake up the system. In earlier generations, this was accomplished by using a special signal that ran across a cable to a defined connector on the motherboard. The NIC would assert the signal for approximately 50 ms to signal a wake up. The integrated GbE controller uses (if configured to) an in-band PM_PME message for this. 122 Datasheet Functional Description At power up, the integrated GbE controller reads the APM Enable bits from the NVM PCI Init Control Word into the APM Enable (APME) bits of the Wake Up Control (WUC) register. These bits control enabling of APM wake up. When APM wake up is enabled, the integrated GbE controller checks all incoming packets for Magic Packets. Once the integrated GbE controller receives a matching Magic Packet, it: * Sets the Magic Packet Received bit in the Wake Up Status (WUS) register. * Sets the PME_Status bit in the Power Management Control/Status Register (PMCSR). APM wake up is supported in all power states and only disabled if a subsequent NVM read results in the APM Wake Up bit being cleared or the software explicitly writes a 0b to the APM Wake Up (APM) bit of the WUC register. Note: APM wake up settings will be restored to NVM default by the PCH when LAN connected Device (PHY) power is turned off and subsequently restored. Some example host WoL flows are: * When system transitions to G3 after WoL is disabled from the BIOS, APM host WoL would get enabled. * Anytime power to the LAN Connected Device (PHY) is cycled while in S4/S5 after WoL is disabled from the BIOS, APM host WoL would get enabled. Anytime power to the LAN Connected Device (PHY) is cycled while in S3, APM host WoL configuration is lost. 5.4.4.1.2 ACPI Power Management Wake Up The integrated GbE controller supports ACPI Power Management based Wake ups. It can generate system wake-up events from three sources: * Receiving a Magic Packet*. * Receiving a Network Wake Up Packet. * Detecting a link change of state. Activating ACPI Power Management Wakeup requires the following steps: * The software device driver programs the Wake Up Filter Control (WUFC) register to indicate the packets it needs to wake up from and supplies the necessary data to the IPv4 Address Table (IP4AT) and the Flexible Filter Mask Table (FFMT), Flexible Filter Length Table (FFLT), and the Flexible Filter Value Table (FFVT). It can also set the Link Status Change Wake Up Enable (LNKC) bit in the Wake Up Filter Control (WUFC) register to cause wake up when the link changes state. * The operating system (at configuration time) writes a 1b to the PME_EN bit of the Power Management Control/Status Register (PMCSR.8). Normally, after enabling wake up, the operating system writes a 11b to the lower two bits of the PMCSR to put the integrated GbE controller into low-power mode. Datasheet 123 Functional Description Once wake up is enabled, the integrated GbE controller monitors incoming packets, first filtering them according to its standard address filtering method, then filtering them with all of the enabled wake-up filters. If a packet passes both the standard address filtering and at least one of the enabled wake-up filters, the integrated GbE controller: * Sets the PME_Status bit in the PMCSR * Sets one or more of the Received bits in the Wake Up Status (WUS) register. (More than one bit is set if a packet matches more than one filter.) If enabled, a link state change wake up causes similar results, setting the Link Status Changed (LNKC) bit in the Wake Up Status (WUS) register when the link goes up or down. After receiving a wake-up packet, the integrated GbE controller ignores any subsequent wake-up packets until the software device driver clears all of the Received bits in the Wake Up Status (WUS) register. It also ignores link change events until the software device driver clears the Link Status Changed (LNKC) bit in the Wake Up Status (WUS) register. Note: ACPI wake up settings are not preserved when the LAN Connected Device (PHY) power is turned off and subsequently restored. Some example host WoL flows are: * Anytime power to the LAN Connected Device (PHY) is cycled while in S3 or S4, ACPI host WoL configuration is lost. 5.4.5 Configurable LEDs The integrated GbE controller supports three controllable and configurable LEDs that are driven from the Intel(R) Ethernet Network Connection I127LM/V Platform LAN Connect Device. Each of the three LED outputs can be individually configured to select the particular event, state, or activity that is indicated on that output. In addition, each LED can be individually configured for output polarity as well as for blinking versus nonblinking (steady-state) indication. The configuration for LED outputs is specified using the LEDCTL register. Furthermore, the hardware-default configuration for all the LED outputs, can be specified using NVM fields; thereby, supporting LED displays configurable to a particular OEM preference. Each of the three LEDs might be configured to use one of a variety of sources for output indication. The MODE bits control the LED source: * LINK_100/1000 is asserted when link is established at either 100 or 1000 Mb/s. * LINK_10/1000 is asserted when link is established at either 10 or 1000 Mb/s. * LINK_UP is asserted when any speed link is established and maintained. * ACTIVITY is asserted when link is established and packets are being transmitted or received. * LINK/ACTIVITY is asserted when link is established AND there is NO transmit or receive activity. * LINK_10 is asserted when a 10 Mb/s link is established and maintained. * LINK_100 is asserted when a 100 Mb/s link is established and maintained. * LINK_1000 is asserted when a 1000 Mb/s link is established and maintained. * FULL_DUPLEX is asserted when the link is configured for full duplex operation. 124 Datasheet Functional Description * COLLISION is asserted when a collision is observed. * PAUSED is asserted when the device's transmitter is flow controlled. * LED_ON is always asserted; LED_OFF is always de-asserted. The IVRT bits enable the LED source to be inverted before being output or observed by the blink-control logic. LED outputs are assumed to normally be connected to the negative side (cathode) of an external LED. The BLINK bits control whether the LED should be blinked while the LED source is asserted, and the blinking frequency (either 200 ms on and 200 ms off or 83 ms on and 83 ms off). The blink control can be especially useful for ensuring that certain events, such as ACTIVITY indication, cause LED transitions, which are sufficiently visible to a human eye. The same blinking rate is shared by all LEDs. 5.4.6 Function Level Reset Support (FLR) The integrated GbE controller supports FLR capability. FLR capability can be used in conjunction with Intel(R) Virtualization Technology. FLR allows an operating system in a Virtual Machine to have complete control over a device, including its initialization, without interfering with the rest of the platform. The device provides a software interface that enables the operating system to reset the entire device as if a PCI reset was asserted. 5.4.6.1 FLR Steps 5.4.6.1.1 FLR Initialization 1. FLR is initiated by software by writing a 1b to the Initiate FLR bit. 2. All subsequent requests targeting the function are not claimed and will be master aborted immediately on the bus. This includes any configuration, I/O or memory cycles. However, the function will continue to accept completions targeting the function. 5.4.6.1.2 FLR Operation Function resets all configuration, I/O, and memory registers of the function except those indicated otherwise and resets all internal states of the function to the default or initial condition. 5.4.6.1.3 FLR Completion The Initiate FLR bit is reset (cleared) when the FLR reset completes. This bit can be used to indicate to the software that the FLR reset completed. Note: Datasheet From the time the Initiate FLR bit is written to 1b, software must wait at least 100 ms before accessing the function. 125 Functional Description 5.5 Low Pin Count (LPC) Bridge (with System and Management Functions) (D31:F0) The LPC bridge function of the PCH resides in PCI D31:F0. In addition to the LPC bridge function, D31:F0 contains other functional units including DMA, Interrupt controllers, Timers, Power Management, System Management, GPIO, and RTC. In this chapter, registers and functions associated with other functional units (power management, GPIO, USB, and so on) are described in their respective sections. Note: The LPC bridge cannot be configured as a subtractive decode agent. 5.5.1 LPC Interface The PCH implements an LPC interface as described in the Low Pin Count Interface Specification, Revision 1.1. The LPC interface to the PCH is shown in Figure 5-4. The PCH implements all of the signals that are shown as optional, but peripherals are not required to do so. Figure 5-4. 126 LPC Interface Diagram Datasheet Functional Description 5.5.1.1 LPC Cycle Types The PCH implements all of the cycle types described in the Low Pin Count Interface Specification, Revision 1.1. Table 5-5 shows the cycle types supported by the PCH. Table 5-5. LPC Cycle Types Supported Cycle Type Comment Memory Read 1 byte only. (See Note 1 below) Memory Write 1 byte only. (See Note 1 below) I/O Read 1 byte only. The PCH breaks up 16-bit and 32-bit processor cycles into multiple 8-bit transfers. I/O Write 1 byte only. The PCH breaks up 16-bit and 32-bit processor cycles into multiple 8-bit transfers. DMA Read Can be 1 or 2 bytes DMA Write Can be 1 or 2 bytes Bus Master Read Can be 1, 2 or 4 bytes. (See Note 2 below) Bus Master Write Can be 1, 2 or 4 bytes. (See Note 2 below) Notes: 1. The PCH provides a single generic memory range (LGMR) for decoding memory cycles and forwarding them as LPC Memory cycles on the LPC bus. The LGMR memory decode range is 64 KB in size and can be defined as being anywhere in the 4 GB memory space. This range needs to be configured by BIOS during POST to provide the necessary memory resources. BIOS should advertise the LPC Generic Memory Range as Reserved to the OS in order to avoid resource conflict. For larger transfers, the PCH performs multiple 8-bit transfers. If the cycle is not claimed by any peripheral, it is subsequently aborted, and the PCH returns a value of all 1s to the processor. This is done to maintain compatibility with ISA memory cycles where pull-up resistors would keep the bus high if no device responds. 2. Bus Master Read or Write cycles must be naturally aligned. For example, a 1-byte transfer can be to any address. However, the 2-byte transfer must be word-aligned (that is, with an address where A0=0). A DWord transfer must be DWord-aligned (that is, with an address where A1 and A0 are both 0). 5.5.1.2 Start Field Definition Table 5-6. Start Field Bit Definitions Bits 3:0 Encoding 0000 Start of cycle for a generic target 0010 Grant for bus master 0 0011 Grant for bus master 1 1111 Stop/Abort: End of a cycle for a target. Note: 5.5.1.3 Definition All other encodings are RESERVED. Cycle Type / Direction (CYCTYPE + DIR) The PCH always drives Bit 0 of this field to 0. Peripherals running bus master cycles must also drive Bit 0 to 0. Table 5-7 shows the valid bit encodings. Table 5-7. Datasheet Cycle Type Bit Definitions (Sheet 1 of 2) Bits 3:2 Bit 1 00 0 I/O Read Definition 00 1 I/O Write 01 0 Memory Read 01 1 Memory Read 10 0 DMA Read 10 1 DMA Write 127 Functional Description Table 5-7. 5.5.1.4 Cycle Type Bit Definitions (Sheet 2 of 2) Bits 3:2 Bit 1 11 x Definition Reserved. If a peripheral performing a bus master cycle generates this value, the PCH aborts the cycle. Size Bits[3:2] are reserved. The PCH always drives them to 00. Peripherals running bus master cycles are also supposed to drive 00 for Bits 3:2; however, the PCH ignores those bits. Bits[1:0] are encoded as listed in Table 5-8. Table 5-8. Transfer Size Bit Definition Bits 1:0 5.5.1.5 Size 00 8-bit transfer (1 byte) 01 16-bit transfer (2 bytes) 10 Reserved. The PCH never drives this combination. If a peripheral running a bus master cycle drives this combination, the PCH may abort the transfer. 11 32-bit transfer (4 bytes) SYNC Valid values for the SYNC field are shown in Table 5-9. Table 5-9. SYNC Bit Definition Bits 3:0 Indication 0000 Ready: SYNC achieved with no error. For DMA transfers, this also indicates DMA request deassertion and no more transfers desired for that channel. 0101 Short Wait: Part indicating wait-states. For bus master cycles, the PCH does not use this encoding. Instead, the PCH uses the Long Wait encoding (see next encoding below). 0110 Long Wait: Part indicating wait-states, and many wait-states will be added. This encoding driven by the PCH for bus master cycles, rather than the Short Wait (0101). 1001 Ready More (Used only by peripheral for DMA cycle): SYNC achieved with no error and more DMA transfers desired to continue after this transfer. This value is valid only on DMA transfers and is not allowed for any other type of cycle. 1010 Error: Sync achieved with error. This is generally used to replace the SERR# or IOCHK# signal on the PCI/ISA bus. It indicates that the data is to be transferred, but there is a serious error in this transfer. For DMA transfers, this not only indicates an error, but also indicates DMA request de-assertion and no more transfers desired for that channel. Notes: 1. All other combinations are RESERVED. 2. If the LPC controller receives any SYNC returned from the device other than short (0101), long wait (0110), or ready (0000) when running a FWH cycle, indeterminate results may occur. A FWH device is not allowed to assert an Error SYNC. 5.5.1.6 SYNC Time-Out There are several error cases that can occur on the LPC interface. The PCH responds as defined in Section 4.2.1.9 of the Low Pin Count Interface Specification, Revision 1.1 to the stimuli described therein. There may be other peripheral failure conditions; however, these are not handled by the PCH. 128 Datasheet Functional Description 5.5.1.7 SYNC Error Indication The PCH responds as defined in Section 4.2.1.10 of the Low Pin Count Interface Specification, Revision 1.1. Upon recognizing the SYNC field indicating an error, the PCH treats this as a SERR by reporting this into the Device 31 Error Reporting Logic. 5.5.1.8 LFRAME# Usage The PCH follows the usage of LFRAME# as defined in the Low Pin Count Interface Specification, Revision 1.1. The PCH performs an abort for the following cases (possible failure cases): * The PCH starts a Memory, I/O, or DMA cycle, but no device drives a valid SYNC after four consecutive clocks. * The PCH starts a Memory, I/O, or DMA cycle, and the peripheral drives an invalid SYNC pattern. * A peripheral drives an illegal address when performing bus master cycles. * A peripheral drives an invalid value. 5.5.1.9 I/O Cycles For I/O cycles targeting registers specified in the PCH's decode ranges, the PCH performs I/O cycles as defined in the Low Pin Count Interface Specification, Revision 1.1. These are 8-bit transfers. If the processor attempts a 16-bit or 32-bit transfer, the PCH breaks the cycle up into multiple 8-bit transfers to consecutive I/O addresses. Note: If the cycle is not claimed by any peripheral (and subsequently aborted), the PCH returns a value of all 1s (FFh) to the processor. This is to maintain compatibility with ISA I/O cycles where pull-up resistors would keep the bus high if no device responds. 5.5.1.10 Bus Master Cycles The PCH supports Bus Master cycles and requests (using LDRQ#) as defined in the Low Pin Count Interface Specification, Revision 1.1. The PCH has two LDRQ# inputs, and thus supports two separate bus master devices. It uses the associated START fields for Bus Master 0 (0010b) or Bus Master 1 (0011b). Note: The PCH does not support LPC Bus Masters performing I/O cycles. LPC Bus Masters should only perform memory read or memory write cycles. 5.5.1.11 LPC Power Management LPCPD# Protocol Same timings as for SUS_STAT#. Upon driving SUS_STAT# low, LPC peripherals drive LDRQ# low or tri-state it. The PCH shuts off the LDRQ# input buffers. After driving SUS_STAT# active, the PCH drives LFRAME# low, and tri-states (or drives low) LAD[3:0]. Note: Datasheet The Low Pin Count Interface Specification, Revision 1.1 defines the LPCPD# protocol where there is at least 30 s from LPCPD# assertion to LRST# assertion. This specification explicitly states that this protocol only applies to entry/exit of low power states which does not include asynchronous reset events. The PCH asserts both 129 Functional Description SUS_STAT# (connects to LPCPD#) and PLTRST# (connects to LRST#) at the same time during a global reset. This is not inconsistent with the LPC LPCPD# protocol. 5.5.1.12 Configuration and PCH Implications LPC I/F Decoders To allow the I/O cycles and memory mapped cycles to go to the LPC interface, the PCH includes several decoders. During configuration, the PCH must be programmed with the same decode ranges as the peripheral. The decoders are programmed using the D 31:F0 configuration space. Note: The PCH cannot accept PCI write cycles from PCI-to-PCI bridges or devices with similar characteristics (specifically those with a "Retry Read" feature which is enabled) to an LPC device if there is an outstanding LPC read cycle towards the same PCI device or bridge. These cycles are not part of normal system operation, but may be encountered as part of platform validation testing using custom test fixtures. Bus Master Device Mapping and START Fields Bus Masters must have a unique START field. In the case of the PCH that supports two LPC bus masters, it drives 0010 for the START field for grants to Bus Master 0 (requested using LDRQ0#) and 0011 for grants to Bus Master 1 (requested using LDRQ1#.). Thus, no registers are needed to configure the START fields for a particular bus master. 5.6 DMA Operation (D31:F0) The PCH supports LPC DMA using the PCH's DMA controller. The DMA controller has registers that are fixed in the lower 64 KB of I/O space. The DMA controller is configured using registers in the PCI configuration space. These registers allow configuration of the channels for use by LPC DMA. The DMA circuitry incorporates the functionality of two 8237 DMA controllers with seven independently programmable channels (Figure 5-5). DMA Controller 1 (DMA-1) corresponds to DMA Channels 0-3 and DMA Controller 2 (DMA-2) corresponds to Channels 5-7. DMA Channel 4 is used to cascade the two controllers and defaults to cascade mode in the DMA Channel Mode (DCM) Register. Channel 4 is not available for any other purpose. In addition to accepting requests from DMA slaves, the DMA controller also responds to requests that software initiates. Software may initiate a DMA service request by setting any bit in the DMA Channel Request Register to a 1. Floppy disk is not supported (or validated) in this PCH. Figure 5-5. PCH DMA Controller Channel 4 Channel 0 Channel 1 Channel 5 DMA-1 Channel 2 Channel 6 Channel 3 Channel 7 DMA-2 Each DMA channel is hardwired to the compatible settings for DMA device size: Channels [3:0] are hardwired to 8-bit, count-by-bytes transfers, and Channels [7:5] are hardwired to 16-bit, count-by-words (address shifted) transfers. 130 Datasheet Functional Description The PCH provides 24-bit addressing in compliance with the ISA-Compatible specification. Each channel includes a 16-bit ISA-Compatible Current Register which holds the sixteen least-significant bits of the 24-bit address, an ISA-Compatible Page Register which contains the eight next most significant bits of address. The DMA controller also features refresh address generation, and auto-initialization following a DMA termination. 5.6.1 Channel Priority For priority resolution, the DMA consists of two logical channel groups: Channels 0-3 and Channels 4-7. Each group may be in either fixed or rotate mode, as determined by the DMA Command Register. DMA I/O slaves normally assert their DREQ line to arbitrate for DMA service. However, a software request for DMA service can be presented through each channel's DMA Request Register. A software request is subject to the same prioritization as any hardware request. See the detailed register description for Request Register programming information in Section 12.2. 5.6.1.1 Fixed Priority The initial fixed priority structure is as follows: High priority Low priority 0, 1, 2, 3 5, 6, 7 The fixed priority ordering is 0, 1, 2, 3, 5, 6, and 7. In this scheme, channel 0 has the highest priority, and channel 7 has the lowest priority. Channels [3:0] of DMA-1 assume the priority position of channel 4 in DMA-2, thus taking priority over Channels 5, 6, and 7. 5.6.1.2 Rotating Priority Rotation allows for "fairness" in priority resolution. The priority chain rotates so that the last channel serviced is assigned the lowest priority in the channel group (0-3, 5-7). Channels 0-3 rotate as a group of 4. They are always placed between Channel 5 and Channel 7 in the priority list. Channel 5-7 rotate as part of a group of 4. That is, Channels (5-7) form the first three positions in the rotation, while Channel Group (0-3) comprises the fourth position in the arbitration. 5.6.2 Address Compatibility Mode When the DMA is operating, the addresses do not increment or decrement through the High and Low Page Registers. Therefore, if a 24-bit address is 01FFFFh and increments, the next address is 010000h, not 020000h. Similarly, if a 24-bit address is 020000h and decrements, the next address is 02FFFFh, not 01FFFFh. However, when the DMA is operating in 16-bit mode, the addresses still do not increment or decrement through the High and Low Page Registers but the page boundary is now 128 K. Therefore, if a 24-bit address is 01FFFEh and increments, the next address is 000000h, not Datasheet 131 Functional Description 0100000h. Similarly, if a 24-bit address is 020000h and decrements, the next address is 03FFFEh, not 02FFFEh. This is compatible with the 8237 and Page Register implementation used in the PC-AT. This mode is set after CPURST is valid. 5.6.3 Summary of DMA Transfer Sizes Table 5-10 lists each of the DMA device transfer sizes. The column labeled "Current Byte/Word Count Register" indicates that the register contents represents either the number of bytes to transfer or the number of 16-bit words to transfer. The column labeled "Current Address Increment/Decrement" indicates the number added to or taken from the Current Address register after each DMA transfer cycle. The DMA Channel Mode Register determines if the Current Address Register will be incremented or decremented. 5.6.3.1 Address Shifting When Programmed for 16-Bit I/O Count by Words Table 5-10. DMA Transfer Size Current Byte/Word Count Register DMA Device Date Size And Word Count Current Address Increment / Decrement 8-Bit I/O, Count By Bytes Bytes 1 16-Bit I/O, Count By Words (Address Shifted) Words 1 The PCH maintains compatibility with the implementation of the DMA in the PC AT that used the 8237. The DMA shifts the addresses for transfers to/from a 16-bit device count-by-words. Note: The least significant bit of the Low Page Register is dropped in 16-bit shifted mode. When programming the Current Address Register (when the DMA channel is in this mode), the Current Address must be programmed to an even address with the address value shifted right by one bit. The address shifting is shown in Table 5-11. Table 5-11. Address Shifting in 16-Bit I/O DMA Transfers Note: 5.6.4 Output Address 8-Bit I/O Programmed Address (Ch 0-3) 16-Bit I/O Programmed Address (Ch 5-7) (Shifted) A0 A[16:1] A[23:17] A0 A[16:1] A[23:17] 0 A[15:0] A[23:17] The least significant bit of the Page Register is dropped in 16-bit shifted mode. Autoinitialize By programming a bit in the DMA Channel Mode Register, a channel may be set up as an autoinitialize channel. When a channel undergoes autoinitialization, the original values of the Current Page, Current Address and Current Byte/Word Count Registers are automatically restored from the Base Page, Address, and Byte/Word Count Registers of that channel following Terminal Count (TC). The Base Registers are loaded simultaneously with the Current Registers by the microprocessor when the DMA channel is programmed and remain unchanged throughout the DMA service. The mask 132 Datasheet Functional Description bit is not set when the channel is in autoinitialize. Following autoinitialize, the channel is ready to perform another DMA service, without processor intervention, as soon as a valid DREQ is detected. 5.6.5 Software Commands There are three additional special software commands that the DMA controller can execute. The three software commands are: * Clear Byte Pointer Flip-Flop * Master Clear * Clear Mask Register They do not depend on any specific bit pattern on the data bus. 5.7 Low Pin Count (LPC) DMA DMA on LPC is handled through the use of the LDRQ# lines from peripherals and special encodings on LAD[3:0] from the host. Single, Demand, Verify, and Increment modes are supported on the LPC interface. Channels 0-3 are 8-bit channels. Channels 5-7 are 16-bit channels. Channel 4 is reserved as a generic bus master request. 5.7.1 Asserting DMA Requests Peripherals that need DMA service encode their requested channel number on the LDRQ# signal. To simplify the protocol, each peripheral on the LPC I/F has its own dedicated LDRQ# signal (they may not be shared between two separate peripherals). The PCH has two LDRQ# inputs, allowing at least two devices to support DMA or bus mastering. LDRQ# is synchronous with LCLK (PCI clock). As shown in Figure 5-6, the peripheral uses the following serial encoding sequence: * Peripheral starts the sequence by asserting LDRQ# low (start bit). LDRQ# is high during idle conditions. * The next three bits contain the encoded DMA channel number (MSB first). * The next bit (ACT) indicates whether the request for the indicated DMA channel is active or inactive. The ACT bit is 1 (high) to indicate if it is active and 0 (low) if it is inactive. The case where ACT is low is rare, and is only used to indicate that a previous request for that channel is being abandoned. * After the active/inactive indication, the LDRQ# signal must go high for at least one clock. After that one clock, LDRQ# signal can be brought low to the next encoding sequence. If another DMA channel also needs to request a transfer, another sequence can be sent on LDRQ#. For example, if an encoded request is sent for Channel 2, and then Channel 3 needs a transfer before the cycle for Channel 2 is run on the interface, the peripheral can send the encoded request for Channel 3. This allows multiple DMA agents behind an I/O device to request use of the LPC interface, and the I/O device does not need to self-arbitrate before sending the message. Datasheet 133 Functional Description Figure 5-6. DMA Request Assertion through LDRQ# LCLK LDRQ# 5.7.2 Start MSB LSB ACT Start Abandoning DMA Requests DMA Requests can be de-asserted in two fashions: on error conditions by sending an LDRQ# message with the `ACT' bit set to 0, or normally through a SYNC field during the DMA transfer. This section describes boundary conditions where the DMA request needs to be removed prior to a data transfer. There may be some special cases where the peripheral desires to abandon a DMA transfer. The most likely case of this occurring is due to a floppy disk controller which has overrun or underrun its FIFO, or software stopping a device prematurely. In these cases, the peripheral wishes to stop further DMA activity. It may do so by sending an LDRQ# message with the ACT bit as 0. However, since the DMA request was seen by the PCH, there is no assurance that the cycle has not been granted and will shortly run on LPC. Therefore, peripherals must take into account that a DMA cycle may still occur. The peripheral can choose not to respond to this cycle, in which case the host will abort it, or it can choose to complete the cycle normally with any random data. This method of DMA de-assertion should be prevented whenever possible, to limit boundary conditions both on the PCH and the peripheral. 5.7.3 General Flow of DMA Transfers Arbitration for DMA channels is performed through the 8237 within the host. Once the host has won arbitration on behalf of a DMA channel assigned to LPC, it asserts LFRAME# on the LPC I/F and begins the DMA transfer. The general flow for a basic DMA transfer is as follows: 1. The PCH starts transfer by asserting 0000b on LAD[3:0] with LFRAME# asserted. 2. The PCH asserts `cycle type' of DMA, direction based on DMA transfer direction. 3. The PCH asserts channel number and, if applicable, terminal count. 4. The PCH indicates the size of the transfer: 8 or 16 bits. 5. If a DMA read... -- The PCH drives the first 8 bits of data and turns the bus around. -- The peripheral acknowledges the data with a valid SYNC. -- If a 16-bit transfer, the process is repeated for the next 8 bits. 6. If a DMA write... -- The PCH turns the bus around and waits for data. -- The peripheral indicates data ready through SYNC and transfers the first byte. -- If a 16-bit transfer, the peripheral indicates data ready and transfers the next byte. 7. The peripheral turns around the bus. 134 Datasheet Functional Description 5.7.4 Terminal Count Terminal count is communicated through LAD[3] on the same clock that DMA channel is communicated on LAD[2:0]. This field is the CHANNEL field. Terminal count indicates the last byte of transfer, based upon the size of the transfer. For example, on an 8-bit transfer size (SIZE field is 00b), if the TC bit is set, then this is the last byte. On a 16-bit transfer (SIZE field is 01b), if the TC bit is set, then the second byte is the last byte. The peripheral, therefore, must internalize the TC bit when the CHANNEL field is communicated, and only signal TC when the last byte of that transfer size has been transferred. 5.7.5 Verify Mode Verify mode is supported on the LPC interface. A verify transfer to the peripheral is similar to a DMA write, where the peripheral is transferring data to main memory. The indication from the host is the same as a DMA write, so the peripheral will be driving data onto the LPC interface. However, the host will not transfer this data into main memory. 5.7.6 DMA Request De-assertion An end of transfer is communicated to the PCH through a special SYNC field transmitted by the peripheral. An LPC device must not attempt to signal the end of a transfer by de-asserting LDREQ#. If a DMA transfer is several bytes (such as, a transfer from a demand mode device) the PCH needs to know when to de-assert the DMA request based on the data currently being transferred. The DMA agent uses a SYNC encoding on each byte of data being transferred, which indicates to the PCH whether this is the last byte of transfer or if more bytes are requested. To indicate the last byte of transfer, the peripheral uses a SYNC value of 0000b (ready with no error), or 1010b (ready with error). These encodings tell the PCH that this is the last piece of data transferred on a DMA read (PCH to peripheral), or the byte that follows is the last piece of data transferred on a DMA write (peripheral to the PCH). When the PCH sees one of these two encodings, it ends the DMA transfer after this byte and de-asserts the DMA request to the 8237. Therefore, if the PCH indicated a 16-bit transfer, the peripheral can end the transfer after one byte by indicating a SYNC value of 0000b or 1010b. The PCH does not attempt to transfer the second byte, and deasserts the DMA request internally. If the peripheral indicates a 0000b or 1010b SYNC pattern on the last byte of the indicated size, then the PCH only de-asserts the DMA request to the 8237 since it does not need to end the transfer. If the peripheral wishes to keep the DMA request active, then it uses a SYNC value of 1001b (ready plus more data). This tells the 8237 that more data bytes are requested after the current byte has been transferred, so the PCH keeps the DMA request active to the 8237. Therefore, on an 8-bit transfer size, if the peripheral indicates a SYNC value of 1001b to the PCH, the data will be transferred and the DMA request will remain active to the 8237. At a later time, the PCH will then come back with another START- CYCTYPE-CHANNEL-SIZE and so on combination to initiate another transfer to the peripheral. Datasheet 135 Functional Description The peripheral must not assume that the next START indication from the PCH is another grant to the peripheral if it had indicated a SYNC value of 1001b. On a single mode DMA device, the 8237 will re-arbitrate after every transfer. Only demand mode DMA devices can be assured that they will receive the next START indication from the PCH. Note: Indicating a 0000b or 1010b encoding on the SYNC field of an odd byte of a 16-bit channel (first byte of a 16-bit transfer) is an error condition. Note: The host stops the transfer on the LPC bus as indicated, fills the upper byte with random data on DMA writes (peripheral to memory), and indicates to the 8237 that the DMA transfer occurred, incrementing the 8237's address and decrementing its byte count. 5.7.7 SYNC Field / LDRQ# Rules Since DMA transfers on LPC are requested through an LDRQ# assertion message, and are ended through a SYNC field during the DMA transfer, the peripheral must obey the following rule when initiating back-to-back transfers from a DMA channel. The peripheral must not assert another message for eight LCLKs after a de-assertion is indicated through the SYNC field. This is needed to allow the 8237, that typically runs off a much slower internal clock, to see a message de-asserted before it is re-asserted so that it can arbitrate to the next agent. Under default operation, the host only performs 8-bit transfers on 8-bit channels and 16-bit transfers on 16-bit channels. The method by which this communication between host and peripheral through system BIOS is performed is beyond the scope of this specification. Since the LPC host and LPC peripheral are motherboard devices, no "plug-n-play" registry is required. The peripheral must not assume that the host is able to perform transfer sizes that are larger than the size allowed for the DMA channel, and be willing to accept a SIZE field that is smaller than what it may currently have buffered. To that end, it is recommended that future devices that may appear on the LPC bus, that require higher bandwidth than 8-bit or 16-bit DMA allow, do so with a bus mastering interface and not rely on the 8237. 5.8 8254 Timers (D31:F0) The PCH contains three counters that have fixed uses. All registers and functions associated with the 8254 timers are in the core well. The 8254 unit is clocked by a 14.318 MHz clock. Counter 0, System Timer This counter functions as the system timer by controlling the state of IRQ0 and is typically programmed for Mode 3 operation. The counter produces a square wave with a period equal to the product of the counter period (838 ns) and the initial count value. The counter loads the initial count value 1 counter period after software writes the count value to the counter I/O address. The counter initially asserts IRQ0 and decrements the count value by two each counter period. The counter negates IRQ0 when the count value reaches 0. It then reloads the initial count value and again 136 Datasheet Functional Description decrements the initial count value by two each counter period. The counter then asserts IRQ0 when the count value reaches 0, reloads the initial count value, and repeats the cycle, alternately asserting and negating IRQ0. Counter 1, Refresh Request Signal This counter provides the refresh request signal and is typically programmed for Mode 2 operation and only impacts the period of the REF_TOGGLE bit in Port 61. The initial count value is loaded one counter period after being written to the counter I/O address. The REF_TOGGLE bit will have a square wave behavior (alternate between 0 and 1) and will toggle at a rate based on the value in the counter. Programming the counter to anything other than Mode 2 will result in undefined behavior for the REF_TOGGLE bit. Counter 2, Speaker Tone This counter provides the speaker tone and is typically programmed for Mode 3 operation. The counter provides a speaker frequency equal to the counter clock frequency (1.193 MHz) divided by the initial count value. The speaker must be enabled by a write to port 061h (see NMI Status and Control ports). 5.8.1 Timer Programming The counter/timers are programmed in the following fashion: 1. Write a control word to select a counter. 2. Write an initial count for that counter. 3. Load the least and/or most significant bytes (as required by Control Word Bits 5, 4) of the 16-bit counter. 4. Repeat with other counters. Only two conventions need to be observed when programming the counters. First, for each counter, the control word must be written before the initial count is written. Second, the initial count must follow the count format specified in the control word (least significant byte only, most significant byte only, or least significant byte and then most significant byte). A new initial count may be written to a counter at any time without affecting the counter's programmed mode. Counting is affected as described in the mode definitions. The new count must follow the programmed count format. If a counter is programmed to read/write two-byte counts, the following precaution applies: A program must not transfer control between writing the first and second byte to another routine which also writes into that same counter. Otherwise, the counter will be loaded with an incorrect count. The Control Word Register at port 43h controls the operation of all three counters. Several commands are available: * Control Word Command. Specifies which counter to read or write, the operating mode, and the count format (binary or BCD). * Counter Latch Command. Latches the current count so that it can be read by the system. The countdown process continues. * Read Back Command. Reads the count value, programmed mode, the current state of the OUT pins, and the state of the Null Count Flag of the selected counter. Table 5-12 lists the six operating modes for the interval counters. Datasheet 137 Functional Description Table 5-12. Counter Operating Modes Mode 5.8.2 Function Description 0 Out signal on end of count (=0) Output is 0. When count goes to 0, output goes to 1 and stays at 1 until counter is reprogrammed. 1 Hardware retriggerable one-shot Output is 0. When count goes to 0, output goes to 1 for one clock time. 2 Rate generator (divide by n counter) Output is 1. Output goes to 0 for one clock time, then back to 1 and counter is reloaded. 3 Square wave output Output is 1. Output goes to 0 when counter rolls over, and counter is reloaded. Output goes to 1 when counter rolls over, and counter is reloaded, and so on. 4 Software triggered strobe Output is 1. Output goes to 0 when count expires for one clock time. 5 Hardware triggered strobe Output is 1. Output goes to 0 when count expires for one clock time. Reading from the Interval Timer It is often desirable to read the value of a counter without disturbing the count in progress. There are three methods for reading the counters: a simple read operation, counter Latch command, and the Read-Back command. Each is explained below. With the simple read and counter latch command methods, the count must be read according to the programmed format; specifically, if the counter is programmed for two byte counts, two bytes must be read. The two bytes do not have to be read one right after the other. Read, write, or programming operations for other counters may be inserted between them. 5.8.2.1 Simple Read The first method is to perform a simple read operation. The counter is selected through Port 40h (Counter 0), 41h (Counter 1), or 42h (Counter 2). Note: Performing a direct read from the counter does not return a determinate value, because the counting process is asynchronous to read operations. However, in the case of Counter 2, the count can be stopped by writing to the GATE bit in Port 61h. 5.8.2.2 Counter Latch Command The Counter Latch command, written to Port 43h, latches the count of a specific counter at the time the command is received. This command is used to ensure that the count read from the counter is accurate, particularly when reading a two-byte count. The count value is then read from each counter's Count register as was programmed by the Control register. The count is held in the latch until it is read or the counter is reprogrammed. The count is then unlatched. This allows reading the contents of the counters on the fly without affecting counting in progress. Multiple Counter Latch Commands may be used to latch more than one counter. Counter Latch commands do not affect the programmed mode of the counter in any way. If a Counter is latched and then, some time later, latched again before the count is read, the second Counter Latch command is ignored. The count read is the count at the time the first Counter Latch command was issued. 138 Datasheet Functional Description 5.8.2.3 Read Back Command The Read Back command, written to Port 43h, latches the count value, programmed mode, and current states of the OUT pin and Null Count flag of the selected counter or counters. The value of the counter and its status may then be read by I/O access to the counter address. The Read Back command may be used to latch multiple counter outputs at one time. This single command is functionally equivalent to several counter latch commands, one for each counter latched. Each counter's latched count is held until it is read or reprogrammed. Once read, a counter is unlatched. The other counters remain latched until they are read. If multiple count Read Back commands are issued to the same counter without reading the count, all but the first are ignored. The Read Back command may additionally be used to latch status information of selected counters. The status of a counter is accessed by a read from that counter's I/O port address. If multiple counter status latch operations are performed without reading the status, all but the first are ignored. Both count and status of the selected counters may be latched simultaneously. This is functionally the same as issuing two consecutive, separate Read Back commands. If multiple count and/or status Read Back commands are issued to the same counters without any intervening reads, all but the first are ignored. If both count and status of a counter are latched, the first read operation from that counter returns the latched status, regardless of which was latched first. The next one or two reads, depending on whether the counter is programmed for one or two type counts, returns the latched count. Subsequent reads return unlatched count. 5.9 8259 Programmable Interrupt Controllers (PIC) (D31:F0) The PCH incorporates the functionality of two 8259 interrupt controllers that provide system interrupts for the ISA compatible interrupts. These interrupts can include: system timer, keyboard controller, serial ports, parallel ports, floppy disk, mouse, and DMA channels. In addition, this interrupt controller can support the PCI based interrupts, by mapping the PCI interrupt onto the compatible ISA interrupt line. Each 8259 controller supports eight interrupts, numbered 0-7. Table 5-13 shows how the controllers are connected. Table 5-13. Interrupt Controller Connections (Sheet 1 of 2) 8259 Master Datasheet 8259 Input Typical Interrupt Source Connected Pin / Function 0 Internal Internal Timer / Counter 0 output / HPET #0 1 Keyboard IRQ1 using SERIRQ 2 Internal Slave controller INTR output 3 Serial Port A IRQ3 using SERIRQ, 4 Serial Port B IRQ4 using SERIRQ, PIRQ# 5 Parallel Port / Generic IRQ5 using SERIRQ, PIRQ# 6 Floppy Disk IRQ6 using SERIRQ, PIRQ# 7 Parallel Port / Generic IRQ7 using SERIRQ, PIRQ# 139 Functional Description Table 5-13. Interrupt Controller Connections (Sheet 2 of 2) 8259 Slave 8259 Input Typical Interrupt Source Connected Pin / Function 0 Internal Real Time Clock Internal RTC / HPET #1 1 Generic IRQ9 using SERIRQ, SCI, TCO, or PIRQ# 2 Generic IRQ10 using SERIRQ, SCI, TCO, or PIRQ# 3 Generic IRQ11 using SERIRQ, SCI, TCO, or PIRQ#, or HPET #2 4 PS/2 Mouse IRQ12 using SERIRQ, SCI, TCO, or PIRQ#, or HPET #3 5 Internal State Machine output based on processor FERR# assertion. May optionally be used for SCI or TCO interrupt if FERR# not needed. 6 SATA SATA Primary (legacy mode), or using SERIRQ or PIRQ# 7 SATA SATA Secondary (legacy mode) or using SERIRQ or PIRQ# The PCH cascades the slave controller onto the master controller through master controller interrupt input 2. This means there are only 15 possible interrupts for the PCH PIC. Interrupts can individually be programmed to be edge or level, except for IRQ0, IRQ2, IRQ8#, and IRQ13. Note: Active-low interrupt sources (such as, the PIRQ#s) are inverted inside the PCH. In the following descriptions of the 8259s, the interrupt levels are in reference to the signals at the internal interface of the 8259s, after the required inversions have occurred. Therefore, the term "high" indicates "active," which means "low" on an originating PIRQ#. 5.9.1 Interrupt Handling 5.9.1.1 Generating Interrupts The PIC interrupt sequence involves three bits, from the IRR, ISR, and IMR, for each interrupt level. These bits are used to determine the interrupt vector returned, and status of any other pending interrupts. Table 5-14 defines the IRR, ISR, and IMR. Table 5-14. Interrupt Status Registers 5.9.1.2 Bit Description IRR Interrupt Request Register. This bit is set on a low to high transition of the interrupt line in edge mode, and by an active high level in level mode. This bit is set whether or not the interrupt is masked. However, a masked interrupt will not generate INTR. ISR Interrupt Service Register. This bit is set, and the corresponding IRR bit cleared, when an interrupt acknowledge cycle is seen, and the vector returned is for that interrupt. IMR Interrupt Mask Register. This bit determines whether an interrupt is masked. Masked interrupts will not generate INTR. Acknowledging Interrupts The processor generates an interrupt acknowledge cycle that is translated by the host bridge into a PCI Interrupt Acknowledge Cycle to the PCH. The PIC translates this command into two internal INTA# pulses expected by the 8259 cores. The PIC uses the first internal INTA# pulse to freeze the state of the interrupts for priority resolution. On the second INTA# pulse, the master or slave sends the interrupt vector to the processor with the acknowledged interrupt code. This code is based upon Bits 7:3 of the corresponding ICW2 register, combined with three bits representing the interrupt within that controller. 140 Datasheet Functional Description Table 5-15. Content of Interrupt Vector Byte 5.9.1.3 Master, Slave Interrupt Bits [7:3] IRQ7,15 ICW2[7:3] Bits [2:0] 111 IRQ6,14 110 IRQ5,13 101 IRQ4,12 100 IRQ3,11 011 IRQ2,10 010 IRQ1,9 001 IRQ0,8 000 Hardware/Software Interrupt Sequence 1. One or more of the Interrupt Request lines (IRQ) are raised high in edge mode, or seen high in level mode, setting the corresponding IRR bit. 2. The PIC sends INTR active to the processor if an asserted interrupt is not masked. 3. The processor acknowledges the INTR and responds with an interrupt acknowledge cycle. The cycle is translated into a PCI interrupt acknowledge cycle by the host bridge. This command is broadcast over PCI by the PCH. 4. Upon observing its own interrupt acknowledge cycle on PCI, the PCH converts it into the two cycles that the internal 8259 pair can respond to. Each cycle appears as an interrupt acknowledge pulse on the internal INTA# pin of the cascaded interrupt controllers. 5. Upon receiving the first internally generated INTA# pulse, the highest priority ISR bit is set and the corresponding IRR bit is reset. On the trailing edge of the first pulse, a slave identification code is broadcast by the master to the slave on a private, internal three bit wide bus. The slave controller uses these bits to determine if it must respond with an interrupt vector during the second INTA# pulse. 6. Upon receiving the second internally generated INTA# pulse, the PIC returns the interrupt vector. If no interrupt request is present because the request was too short in duration, the PIC returns vector 7 from the master controller. 7. This completes the interrupt cycle. In AEOI mode the ISR bit is reset at the end of the second INTA# pulse. Otherwise, the ISR bit remains set until an appropriate EOI command is issued at the end of the interrupt subroutine. 5.9.2 Initialization Command Words (ICWx) Before operation can begin, each 8259 must be initialized. In the PCH, this is a four byte sequence. The four initialization command words are referred to by their acronyms: ICW1, ICW2, ICW3, and ICW4. The base address for each 8259 initialization command word is a fixed location in the I/O memory space: 20h for the master controller, and A0h for the slave controller. 5.9.2.1 ICW1 An I/O write to the master or slave controller base address with data bit 4 equal to 1 is interpreted as a write to ICW1. Upon sensing this write, the PCH's PIC expects three more byte writes to 21h for the master controller, or A1h for the slave controller, to complete the ICW sequence. Datasheet 141 Functional Description A write to ICW1 starts the initialization sequence during which the following automatically occur: 1. Following initialization, an interrupt request (IRQ) input must make a low-to-high transition to generate an interrupt. 2. The Interrupt Mask Register is cleared. 3. IRQ7 input is assigned priority 7. 4. The slave mode address is set to 7. 5. Special mask mode is cleared and Status Read is set to IRR. 5.9.2.2 ICW2 The second write in the sequence (ICW2) is programmed to provide bits [7:3] of the interrupt vector that will be released during an interrupt acknowledge. A different base is selected for each interrupt controller. 5.9.2.3 ICW3 The third write in the sequence (ICW3) has a different meaning for each controller. * For the master controller, ICW3 is used to indicate which IRQ input line is used to cascade the slave controller. Within the PCH, IRQ2 is used. Therefore, Bit 2 of ICW3 on the master controller is set to a 1, and the other bits are set to 0s. * For the slave controller, ICW3 is the slave identification code used during an interrupt acknowledge cycle. On interrupt acknowledge cycles, the master controller broadcasts a code to the slave controller if the cascaded interrupt won arbitration on the master controller. The slave controller compares this identification code to the value stored in its ICW3, and if it matches, the slave controller assumes responsibility for broadcasting the interrupt vector. 5.9.2.4 ICW4 The final write in the sequence (ICW4) must be programmed for both controllers. At the very least, Bit 0 must be set to a 1 to indicate that the controllers are operating in an Intel Architecture-based system. 5.9.3 Operation Command Words (OCW) These command words reprogram the Interrupt controller to operate in various interrupt modes. * OCW1 masks and unmasks interrupt lines. * OCW2 controls the rotation of interrupt priorities when in rotating priority mode, and controls the EOI function. * OCW3 sets up ISR/IRR reads, enables/disables the special mask mode (SMM), and enables/disables polled interrupt mode. 142 Datasheet Functional Description 5.9.4 Modes of Operation 5.9.4.1 Fully Nested Mode In this mode, interrupt requests are ordered in priority from 0 through 7, with 0 being the highest. When an interrupt is acknowledged, the highest priority request is determined and its vector placed on the bus. Additionally, the ISR for the interrupt is set. This ISR bit remains set until: the processor issues an EOI command immediately before returning from the service routine; or if in AEOI mode, on the trailing edge of the second INTA#. While the ISR bit is set, all further interrupts of the same or lower priority are inhibited, while higher levels generate another interrupt. Interrupt priorities can be changed in the rotating priority mode. 5.9.4.2 Special Fully-Nested Mode This mode is used in the case of a system where cascading is used, and the priority has to be conserved within each slave. In this case, the special fully-nested mode is programmed to the master controller. This mode is similar to the fully-nested mode with the following exceptions: * When an interrupt request from a certain slave is in service, this slave is not locked out from the master's priority logic and further interrupt requests from higher priority interrupts within the slave are recognized by the master and initiate interrupts to the processor. In the normal-nested mode, a slave is masked out when its request is in service. * When exiting the Interrupt Service routine, software has to check whether the interrupt serviced was the only one from that slave. This is done by sending a NonSpecific EOI command to the slave and then reading its ISR. If it is 0, a nonspecific EOI can also be sent to the master. 5.9.4.3 Automatic Rotation Mode (Equal Priority Devices) In some applications, there are a number of interrupting devices of equal priority. Automatic rotation mode provides for a sequential 8-way rotation. In this mode, a device receives the lowest priority after being serviced. In the worst case, a device requesting an interrupt has to wait until each of seven other devices are serviced at most once. There are two ways to accomplish automatic rotation using OCW2; the Rotation on Non-Specific EOI Command (R=1, SL=0, EOI=1) and the rotate in automatic EOI mode which is set by (R=1, SL=0, EOI=0). 5.9.4.4 Specific Rotation Mode (Specific Priority) Software can change interrupt priorities by programming the bottom priority. For example, if IRQ5 is programmed as the bottom priority device, then IRQ6 is the highest priority device. The Set Priority Command is issued in OCW2 to accomplish this, where: R=1, SL=1, EOI=0 and LO-L2 is the binary priority level code of the bottom priority device. In this mode, internal status is updated by software control during OCW2. However, it is independent of the EOI command. Priority changes can be executed during an EOI command by using the Rotate on Specific EOI Command in OCW2 (R=1, SL=1, EOI=1) and LO-L2=IRQ level to receive bottom priority. Datasheet 143 Functional Description 5.9.4.5 Poll Mode Poll mode can be used to conserve space in the interrupt vector table. Multiple interrupts that can be serviced by one interrupt service routine do not need separate vectors if the service routine uses the poll command. Poll mode can also be used to expand the number of interrupts. The polling interrupt service routine can call the appropriate service routine, instead of providing the interrupt vectors in the vector table. In this mode, the INTR output is not used and the microprocessor internal Interrupt Enable flip-flop is reset, disabling its interrupt input. Service to devices is achieved by software using a Poll command. The Poll command is issued by setting P=1 in OCW3. The PIC treats its next I/O read as an interrupt acknowledge, sets the appropriate ISR bit if there is a request, and reads the priority level. Interrupts are frozen from the OCW3 write to the I/O read. The byte returned during the I/O read contains a 1 in Bit 7 if there is an interrupt, and the binary code of the highest priority level in Bits 2:0. 5.9.4.6 Edge and Level Triggered Mode In ISA systems this mode is programmed using Bit 3 in ICW1, which sets level or edge for the entire controller. In the PCH, this bit is disabled and a register for edge and level triggered mode selection, per interrupt input, is included. This is the Edge/Level control Registers ELCR1 and ELCR2. If an ELCR bit is 0, an interrupt request will be recognized by a low-to-high transition on the corresponding IRQ input. The IRQ input can remain high without generating another interrupt. If an ELCR bit is 1, an interrupt request will be recognized by a high level on the corresponding IRQ input and there is no need for an edge detection. The interrupt request must be removed before the EOI command is issued to prevent a second interrupt from occurring. In both the edge and level triggered modes, the IRQ inputs must remain active until after the falling edge of the first internal INTA#. If the IRQ input goes inactive before this time, a default IRQ7 vector is returned. 5.9.4.7 End of Interrupt (EOI) Operations An EOI can occur in one of two fashions: by a command word write issued to the PIC before returning from a service routine, the EOI command; or automatically when AEOI bit in ICW4 is set to 1. 5.9.4.8 Normal End of Interrupt In normal EOI, software writes an EOI command before leaving the interrupt service routine to mark the interrupt as completed. There are two forms of EOI commands: Specific and Non-Specific. When a Non-Specific EOI command is issued, the PIC clears the highest ISR bit of those that are set to 1. Non-Specific EOI is the normal mode of operation of the PIC within the PCH, as the interrupt being serviced currently is the interrupt entered with the interrupt acknowledge. When the PIC is operated in modes that preserve the fully nested structure, software can determine which ISR bit to clear by issuing a Specific EOI. An ISR bit that is masked is not cleared by a Non-Specific EOI if the PIC is in the special mask mode. An EOI command must be issued for both the master and slave controller. 144 Datasheet Functional Description 5.9.4.9 Automatic End of Interrupt Mode In this mode, the PIC automatically performs a Non-Specific EOI operation at the trailing edge of the last interrupt acknowledge pulse. From a system standpoint, this mode should be used only when a nested multi-level interrupt structure is not required within a single PIC. The AEOI mode can only be used in the master controller and not the slave controller. 5.9.5 Masking Interrupts 5.9.5.1 Masking on an Individual Interrupt Request Each interrupt request can be masked individually by the Interrupt Mask Register (IMR). This register is programmed through OCW1. Each bit in the IMR masks one interrupt channel. Masking IRQ2 on the master controller masks all requests for service from the slave controller. 5.9.5.2 Special Mask Mode Some applications may require an interrupt service routine to dynamically alter the system priority structure during its execution under software control. For example, the routine may wish to inhibit lower priority requests for a portion of its execution but enable some of them for another portion. The special mask mode enables all interrupts not masked by a bit set in the Mask register. Normally, when an interrupt service routine acknowledges an interrupt without issuing an EOI to clear the ISR bit, the interrupt controller inhibits all lower priority requests. In the special mask mode, any interrupts may be selectively enabled by loading the Mask Register with the appropriate pattern. The special mask mode is set by OCW3 where: SSMM=1, SMM=1, and cleared where SSMM=1, SMM=0. 5.9.6 Steering PCI Interrupts The PCH can be programmed to allow PIRQA#-PIRQH# to be routed internally to interrupts 3-7, 9-12, 14 or 15. The assignment is programmable through the PIRQx Route Control registers, located at 60-63h and 68-6Bh in D31:F0. One or more PIRQx# lines can be routed to the same IRQx input. If interrupt steering is not required, the Route registers can be programmed to disable steering. The PIRQx# lines are defined as active low, level sensitive to allow multiple interrupts on a PCI board to share a single line across the connector. When a PIRQx# is routed to specified IRQ line, software must change the IRQ's corresponding ELCR bit to level sensitive mode. The PCH internally inverts the PIRQx# line to send an active high level to the PIC. When a PCI interrupt is routed onto the PIC, the selected IRQ can no longer be used by an active high device (through SERIRQ). However, active low interrupts can share their interrupt with PCI interrupts. Internal sources of the PIRQs, including SCI and TCO interrupts, cause the external PIRQ to be asserted. The PCH receives the PIRQ input, like all of the other external sources, and routes it accordingly. Datasheet 145 Functional Description 5.10 Advanced Programmable Interrupt Controller (APIC) (D31:F0) In addition to the standard ISA-compatible PIC described in the previous section, the PCH incorporates the APIC. While the standard interrupt controller is intended for use in a uni-processor system, APIC can be used in either a uni-processor or multiprocessor system. 5.10.1 Interrupt Handling The I/O APIC handles interrupts very differently than the 8259. Briefly, these differences are: * Method of Interrupt Transmission. The I/O APIC transmits interrupts through memory writes on the normal data path to the processor, and interrupts are handled without the need for the processor to run an interrupt acknowledge cycle. * Interrupt Priority. The priority of interrupts in the I/O APIC is independent of the interrupt number. For example, interrupt 10 can be given a higher priority than interrupt 3. * More Interrupts. The I/O APIC in the PCH supports a total of 24 interrupts. * Multiple Interrupt Controllers. The I/O APIC architecture allows for multiple I/O APIC devices in the system with their own interrupt vectors. 5.10.2 Interrupt Mapping The I/O APIC within the PCH supports 24 APIC interrupts. Each interrupt has its own unique vector assigned by software. The interrupt vectors are mapped as shown in the following table. Table 5-16. APIC Interrupt Mapping1 (Sheet 1 of 2) Using SERIRQ Direct from Pin 0 No No No 1 Yes No Yes 2 No No No 3 Yes No Yes 4 Yes No Yes 5 Yes No Yes 6 Yes No Yes 7 Yes No Yes 8 No No No RTC, HPET #1 (legacy mode) 9 Yes No Yes Option for SCI, TCO 10 Yes No Yes Option for SCI, TCO 11 Yes No Yes HPET #2, Option for SCI, TCO (Note 2) 12 Yes No Yes HPET #3 (Note 3) 13 No No No FERR# logic 14 Yes No Yes SATA Primary (legacy mode) 15 Yes No Yes SATA Secondary (legacy mode) IRQ # 146 Using PCI Message Internal Modules Cascade from 8259 #1 8254 Counter 0, HPET #0 (legacy mode) Datasheet Functional Description Table 5-16. APIC Interrupt Mapping1 (Sheet 2 of 2) IRQ # Using SERIRQ Direct from Pin Using PCI Message 16 17 PIRQA# PIRQA# Yes PIRQB# PIRQB# Internal devices are routable; see Section 10.1.17 though Section 10.1.33. Yes Option for SCI, TCO, HPET #0,1,2, 3. Other internal devices are routable; see Section 10.1.17 though Section 10.1.33. 18 PIRQC# PIRQC# 19 PIRQD# PIRQD# 20 N/A PIRQE#4 21 N/A PIRQF#4 22 N/A PIRQG#4 23 N/A PIRQH#4 Internal Modules Notes: 1. When programming the polarity of internal interrupt sources on the APIC, interrupts 0 through 15 receive active-high internal interrupt sources, while interrupts 16 through 23 receive active-low internal interrupt sources. 2. If IRQ 11 is used for HPET #2, software should ensure IRQ 11 is not shared with any other devices to ensure the proper operation of HPET #2. The PCH hardware does not prevent sharing of IRQ 11. 3. If IRQ 12 is used for HPET #3, software should ensure IRQ 12 is not shared with any other devices to ensure the proper operation of HPET #3. The PCH hardware does not prevent sharing of IRQ 12. 4. PIRQ[E:H] are Multiplexed with GPIO pins. Interrupts PIRQ[E:H] will not be exposed if they are configured as GPIOs. 5.10.3 PCI / PCI Express* Message-Based Interrupts When external devices through PCI/PCI Express wish to generate an interrupt, they will send the message defined in the PCI Express* Base Specification, Revision 2.0 for generating INTA# - INTD#. These will be translated internal assertions/de-assertions of INTA# - INTD#. 5.10.4 IOxAPIC Address Remapping To support Intel Virtualization Technology, interrupt messages are required to go through similar address remapping as any other memory request. Address remapping allows for domain isolation for interrupts, so a device assigned in one domain is not allowed to generate an interrupt to another domain. The address remapping is based on the Bus: Device: Function field associated with the requests. The internal APIC is required to initiate the interrupt message using a unique Bus: Device: Function. The PCH allows BIOS to program the unique Bus: Device: Function address for the internal APIC. This address field does not change the APIC functionality and the APIC is not promoted as a stand-alone PCI device. See Device 31: Function 0 Offset 6Ch for additional information. 5.10.5 External Interrupt Controller Support The PCH supports external APICs off of PCI Express ports but does not support APICs on the PCI bus. The EOI special cycle is only forwarded to PCI Express ports. Datasheet 147 Functional Description 5.11 Serial Interrupt (D31:F0) The PCH supports a serial IRQ scheme. This allows a single signal to be used to report interrupt requests. The signal used to transmit this information is shared between the PCH and all participating peripherals. The signal line, SERIRQ, is synchronous to PCI clock, and follows the sustained tri-state protocol that is used by all PCI signals. This means that if a device has driven SERIRQ low, it will first drive it high synchronous to PCI clock and release it the following PCI clock. The serial IRQ protocol defines this sustained tri-state signaling in the following fashion: * S - Sample Phase. Signal driven low * R - Recovery Phase. Signal driven high * T - Turn-around Phase. Signal released The PCH supports a message for 21 serial interrupts. These represent the 15 ISA interrupts (IRQ0-1, 3-15), the four PCI interrupts, and the control signals SMI# and IOCHK#. The serial IRQ protocol does not support the additional APIC interrupts (20-23). Note: When the SATA controller is configured for legacy IDE mode, IRQ14 and IRQ15 are expected to behave as ISA legacy interrupts that cannot be shared (that is, through the Serial Interrupt pin). If IRQ14 and IRQ15 are shared with Serial Interrupt pin then abnormal system behavior may occur. For example, IRQ14/15 may not be detected by the PCH's interrupt controller. When the SATA controller is not running in Native IDE mode, IRQ14 and IRQ15 are used as special interrupts. If the SATA controller is in native mode, these interrupts can be mapped to other devices accordingly. 5.11.1 Start Frame The serial IRQ protocol has two modes of operation which affect the start frame. These two modes are: Continuous, where the PCH is solely responsible for generating the start frame; and Quiet, where a serial IRQ peripheral is responsible for beginning the start frame. The mode that must first be entered when enabling the serial IRQ protocol is continuous mode. In this mode, the PCH asserts the start frame. This start frame is 4, 6, or 8 PCI clocks wide based upon the Serial IRQ Control Register, bits 1:0 at 64h in D31:F0 configuration space. This is a polling mode. When the serial IRQ stream enters quiet mode (signaled in the Stop Frame), the SERIRQ line remains inactive and pulled up between the Stop and Start Frame until a peripheral drives the SERIRQ signal low. The PCH senses the line low and continues to drive it low for the remainder of the Start Frame. Since the first PCI clock of the start frame was driven by the peripheral in this mode, the PCH drives the SERIRQ line low for 1 PCI clock less than in continuous mode. This mode of operation allows for a quiet, and therefore lower power, operation. 5.11.2 Data Frames Once the Start frame has been initiated, all of the SERIRQ peripherals must start counting frames based on the rising edge of SERIRQ. Each of the IRQ/DATA frames has exactly 3 phases of 1 clock each: * Sample Phase. During this phase, the SERIRQ device drives SERIRQ low if the corresponding interrupt signal is low. If the corresponding interrupt is high, then the SERIRQ devices tri-state the SERIRQ signal. The SERIRQ line remains high due 148 Datasheet Functional Description to pull-up resistors (there is no internal pull-up resistor on this signal, an external pull-up resistor is required). A low level during the IRQ0-1 and IRQ2-15 frames indicates that an active-high ISA interrupt is not being requested, but a low level during the PCI INT[A:D], SMI#, and IOCHK# frame indicates that an active-low interrupt is being requested. * Recovery Phase. During this phase, the device drives the SERIRQ line high if in the Sample Phase it was driven low. If it was not driven in the sample phase, it is tri-stated in this phase. * Turn-around Phase. The device tri-states the SERIRQ line 5.11.3 Stop Frame After all data frames, a Stop Frame is driven by the PCH. The SERIRQ signal is driven low by the PCH for 2 or 3 PCI clocks. The number of clocks is determined by the SERIRQ configuration register. The number of clocks determines the next mode. Table 5-17. Stop Frame Explanation Stop Frame Width 5.11.4 Next Mode 2 PCI clocks Quiet Mode. Any SERIRQ device may initiate a Start Frame 3 PCI clocks Continuous Mode. Only the host (the PCH) may initiate a Start Frame Specific Interrupts Not Supported Using SERIRQ There are three interrupts seen through the serial stream that are not supported by the PCH. These interrupts are generated internally, and are not sharable with other devices within the system. These interrupts are: * IRQ0. Heartbeat interrupt generated off of the internal 8254 counter 0. * IRQ8#. RTC interrupt can only be generated internally. * IRQ13. Floating point error interrupt generated off of the processor assertion of FERR#. The PCH ignores the state of these interrupts in the serial stream, and does not adjust their level based on the level seen in the serial stream. 5.11.5 Data Frame Format Table 5-18 shows the format of the data frames. For the PCI interrupts (A-D), the output from the PCH is AND'd with the PCI input signal. This way, the interrupt can be signaled using both the PCI interrupt input signal and using the SERIRQ signal (they are shared). Table 5-18. Data Frame Format (Sheet 1 of 2) Datasheet Data Frame # Interrupt Clocks Past Start Frame 1 IRQ0 2 2 IRQ1 5 3 SMI# 8 4 IRQ3 11 5 IRQ4 14 6 IRQ5 17 7 IRQ6 20 8 IRQ7 23 Comment Ignored. IRQ0 can only be generated using the internal 8524 Causes SMI# if low. Will set the SERIRQ_SMI_STS bit. 149 Functional Description Table 5-18. Data Frame Format (Sheet 2 of 2) Data Frame # 5.12 Interrupt Clocks Past Start Frame Comment 9 IRQ8 26 10 IRQ9 29 Ignored. IRQ8# can only be generated internally. 11 IRQ10 32 12 IRQ11 35 13 IRQ12 38 14 IRQ13 41 Ignored. IRQ13 can only be generated from FERR# 15 IRQ14 44 Not attached to SATA logic 16 IRQ15 47 Not attached to SATA logic 17 IOCHCK# 50 Same as ISA IOCHCK# going active. 18 PCI INTA# 53 Drive PIRQA# 19 PCI INTB# 56 Drive PIRQB# 20 PCI INTC# 59 Drive PIRQC# 21 PCI INTD# 62 Drive PIRQD# Real Time Clock (D31:F0) The Real Time Clock (RTC) module provides a battery backed-up date and time keeping device with two banks of static RAM with 128 bytes each, although the first bank has 114 bytes for general purpose usage. Three interrupt features are available: time of day alarm with once a second to once a month range, periodic rates of 122 s to 500 ms, and end of update cycle notification. Seconds, minutes, hours, days, day of week, month, and year are counted. Daylight savings compensation is no longer supported. The hour is represented in twelve or twenty-four hour format, and data can be represented in BCD or binary format. The design is functionally compatible with the Motorola MS146818B. The time keeping comes from a 32.768 kHz oscillating source, which is divided to achieve an update every second. The lower 14 bytes on the lower RAM block has very specific functions. The first ten are for time and date information. The next four (0Ah to 0Dh) are registers, which configure and report RTC functions. The time and calendar data should match the data mode (BCD or binary) and hour mode (12 or 24 hour) as selected in register B. It is up to the programmer to make sure that data stored in these locations is within the reasonable values ranges and represents a possible date and time. The exception to these ranges is to store a value of C0-FFh in the Alarm bytes to indicate a don't care situation. All Alarm conditions must match to trigger an Alarm Flag, which could trigger an Alarm Interrupt if enabled. The SET bit must be 1 while programming these locations to avoid clashes with an update cycle. Access to time and date information is done through the RAM locations. If a RAM read from the ten time and date bytes is attempted during an update cycle, the value read do not necessarily represent the true contents of those locations. Any RAM writes under the same conditions are ignored. Note: The leap year determination for adding a 29th day to February does not take into account the end-of-the-century exceptions. The logic simply assumes that all years divisible by 4 are leap years. According to the Royal Observatory Greenwich, years that are divisible by 100 are typically not leap years. In every fourth century (years divisible by 400, like 2000), the 100-year-exception is over-ridden and a leap-year occurs. The year 2100 will be the first time in which the current RTC implementation would incorrectly calculate the leap-year. The PCH does not implement month/year alarms. 150 Datasheet Functional Description 5.12.1 Update Cycles An update cycle occurs once a second, if the SET bit of register B is not asserted and the divide chain is properly configured. During this procedure, the stored time and date are incremented, overflow is checked, a matching alarm condition is checked, and the time and date are rewritten to the RAM locations. The update cycle will start at least 488 s after the UIP bit of register A is asserted, and the entire cycle does not take more than 1984 s to complete. The time and date RAM locations (0-9) are disconnected from the external bus during this time. To avoid update and data corruption conditions, external RAM access to these locations can safely occur at two times. When a updated-ended interrupt is detected, almost 999 ms is available to read and write the valid time and date data. If the UIP bit of Register A is detected to be low, there is at least 488 s before the update cycle begins. Warning: The overflow conditions for leap years adjustments are based on more than one date or time item. To ensure proper operation when adjusting the time, the new time and data values should be set at least two seconds before leap year occurs. 5.12.2 Interrupts The real-time clock interrupt is internally routed within the PCH both to the I/O APIC and the 8259. It is mapped to interrupt vector 8. This interrupt does not leave the PCH, nor is it shared with any other interrupt. IRQ8# from the SERIRQ stream is ignored. However, the High Performance Event Timers can also be mapped to IRQ8#; in this case, the RTC interrupt is blocked. 5.12.3 Lockable RAM Ranges The RTC battery-backed RAM supports two 8-byte ranges that can be locked using the configuration space. If the locking bits are set, the corresponding range in the RAM will not be readable or writable. A write cycle to those locations will have no effect. A read cycle to those locations will not return the location's actual value (resultant value is undefined). Once a range is locked, the range can be unlocked only by a hard reset, which will invoke the BIOS and allow it to relock the RAM range. 5.12.4 Century Rollover The PCH detects a rollover when the Year byte (RTC I/O space, index Offset 09h) transitions form 99 to 00. Upon detecting the rollover, the PCH sets the NEWCENTURY_STS bit (TCOBASE + 04h, Bit 7). If the system is in an S0 state, this causes an SMI#. The SMI# handler can update registers in the RTC RAM that are associated with century value. If the system is in a sleep state (S1-S5) when the century rollover occurs, the PCH also sets the NEWCENTURY_STS bit, but no SMI# is generated. When the system resumes from the sleep state, BIOS should check the NEWCENTURY_STS bit and update the century value in the RTC RAM. 5.12.5 Clearing Battery-Backed RTC RAM Clearing CMOS RAM in a PCH-based platform can be done by using a jumper on RTCRST# or GPI. Implementations should not attempt to clear CMOS by using a jumper to pull VccRTC low. Datasheet 151 Functional Description Using RTCRST# to Clear CMOS A jumper on RTCRST# can be used to clear CMOS values, as well as reset to default, the state of those configuration bits that reside in the RTC power well. When the RTCRST# is strapped to ground, the RTC_PWR_STS bit (D31:F0:A4h Bit 2) will be set and those configuration bits in the RTC power well will be set to their default state. BIOS can monitor the state of this Bit, and manually clear the RTC CMOS array once the system is booted. The normal position would cause RTCRST# to be pulled up through a weak pull-up resistor. Table 5-19 shows which bits are set to their default state when RTCRST# is asserted. This RTCRST# jumper technique allows the jumper to be moved and then replaced--all while the system is powered off. Then, once booted, the RTC_PWR_STS can be detected in the set state. Table 5-19. Configuration Bits Reset by RTCRST# Assertion Bit Name Register Location Bit(s) Default State Alarm Interrupt Enable (AIE) Register B (General Configuration) (RTC_REGB) I/O space (RTC Index + 0Bh) 5 X Alarm Flag (AF) Register C (Flag Register) (RTC_REGC) I/O space (RTC Index + 0Ch) 5 X SWSMI_RATE_SEL General PM Configuration 3 Register GEN_PMCON_3 D31:F0:A4h 7:6 0 SLP_S4# Minimum Assertion Width General PM Configuration 3 Register GEN_PMCON_3 D31:F0:A4h 5:4 0 SLP_S4# Assertion Stretch Enable General PM Configuration 3 Register GEN_PMCON_3 D31:F0:A4h 3 0 RTC Power Status (RTC_PWR_STS) General PM Configuration 3 Register GEN_PMCON_3 D31:F0:A4h 2 0 Power Failure (PWR_FLR) General PM Configuration 3 Register (GEN_PMCON_3) D31:F0:A4h 1 0 AFTERG3_EN General PM Configuration 3 Register GEN_PMCON_3 D31:F0:A4h 0 0 Power Button Override Status (PRBTNOR_STS) Power Management 1 Status Register (PM1_STS) PMBase + 00h 11 0 RTC Event Enable (RTC_EN) Power Management 1 Enable Register (PM1_EN) PMBase + 02h 10 0 Sleep Type (SLP_TYP) Power Management 1 Control (PM1_CNT) PMBase + 04h 12:10 0 PME_EN General Purpose Event 0 Enables Register (GPE0_EN) PMBase + 2Ch 11 0 BATLOW_EN General Purpose Event 0 Enables Register (GPE0_EN) PMBase + 2Ch 10 0 RI_EN General Purpose Event 0 Enables Register (GPE0_EN) PMBase + 2Ch NEWCENTURY_STS TCO1 Status Register (TCO1_STS) TCOBase + 04h Intruder Detect (INTRD_DET) TCO2 Status Register (TCO2_STS) TCOBase + 06h Top Swap (TS) Backed Up Control Register (BUC) Chipset Config Registers:Offset 3414h 8 0 7 0 0 0 0 X Using a GPI to Clear CMOS A jumper on a GPI can also be used to clear CMOS values. BIOS would detect the setting of this GPI on system boot-up, and manually clear the CMOS array. Note: The GPI strap technique to clear CMOS requires multiple steps to implement. The system is booted with the jumper in new position, then powered back down. The jumper is replaced back to the normal position, then the system is rebooted again. Warning: Do not implement a jumper on VccRTC to clear CMOS. 152 Datasheet Functional Description 5.13 Processor Interface (D31:F0) The PCH interfaces to the processor with following pin-based signals other than DMI: * Standard Outputs to processor: PROCPWRGD, PMSYNCH, PECI * Standard Input from processor: THRMTRIP# Most PCH outputs to the processor use standard buffers. The PCH has separate V_PROC_IO signals that are pulled up at the system level to the processor voltage, and thus determines VOH for the outputs to the processor. The following processor interface legacy pins were removed from the PCH: * IGNNE#, STPCLK#, DPSLP#, are DPRSLPVR are no longer required on PCH based systems. * A20M#, SMI#, NMI, INIT#, INTR, FERR#: Functionality has been replaced by inband Virtual Legacy Wire (VLW) messages. See Section 5.13.3. 5.13.1 Processor Interface Signals and VLW Messages This section describes each of the signals that interface between the PCH and the processor(s). The behavior of some signals may vary during processor reset, as the signals are used for frequency strapping. 5.13.1.1 INIT (Initialization) The INIT# VLW Message is asserted based on any one of several events described in Table 5-20. When any of these events occur, INIT# is asserted for 16 PCI clocks, then driven high. Table 5-20. INIT# Going Active Cause of INIT# Going Active Comment Shutdown special cycle from processor observed on PCHprocessor interconnect. INIT assertion based on value of Shutdown Policy Select register (SPS) PORT92 write, where INIT_NOW (Bit 0) transitions from a 0 to a 1. PORTCF9 write, where SYS_RST (Bit 1) was a 0 and RST_CPU (Bit 2) transitions from 0 to 1. 5.13.1.2 RCIN# input signal goes low. RCIN# is expected to be driven by the external microcontroller (KBC). 0 to 1 transition on RCIN# must occur before the PCH will arm INIT# to be generated again. Note: RCIN# signal is expected to be low during S3, S4, and S5 states. Transition on the RCIN# signal in those states (or the transition to those states) may not necessarily cause the INIT# signal to be generated to the processor. Processor BIST To enter BIST, software sets CPU_BIST_EN bit and then does a full processor reset using the CF9 register. FERR# (Numeric Coprocessor Error) The PCH supports the coprocessor error function with the FERR# message. The function is enabled using the CEN bit. If FERR# is driven active by the processor, IRQ13 goes active (internally). When it detects a write to the COPROC_ERR register (I/O Datasheet 153 Functional Description Register F0h), the PCH negates the internal IRQ13 and IGNNE# will be active. IGNNE# remains active until FERR# is driven inactive. IGNNE# is never driven active unless FERR# is active. Note: IGNNE# (Ignore Numeric Error is now internally generated by the processor. 5.13.1.3 NMI (Non-Maskable Interrupt) Non-Maskable Interrupts (NMIs) can be generated by several sources, as described in Table 5-21. Table 5-21. NMI Sources Cause of NMI 5.13.1.4 Comment SERR# goes active (either internally, externally using SERR# signal, or using message from processor) Can instead be routed to generate an SCI, through the NMI2SCI_EN bit (D31:F0, TCO Base + 08h, Bit 11). IOCHK# goes active using SERIRQ# stream (ISA system Error) Can instead be routed to generate an SCI, through the NMI2SCI_EN bit (D31:F0, TCO Base + 08h, Bit 11). SECSTS Register D31:F0 Offset 1Eh, bit 8. This is enabled by the Parity Error Response Bit (PER). DEV_STS Register D31:F0 Offset 06h, bit 8 This is enabled by the Parity Error Response Bit (PER). GPIO[15:0] when configured as a General Purpose input and routed as NMI (by GPIO_ROUT at D31:F0 Offset B8) This is enabled by GPI NMI Enable (GPI_NMI_EN) bits at D31:F0 Offset: GPIOBASE + 28h bits 15:0 Processor Power Good (PROCPWRGD) This signal is connected to the processor UNCOREPWRGOOD input to indicate when the processor power is valid. 5.13.2 Dual-Processor Issues 5.13.2.1 Usage Differences In dual-processor designs, some of the processor signals are unused or used differently than for uniprocessor designs. * FERR# are generally not used, but still supported. * I/O APIC and SMI# are assumed to be used. 5.13.3 Virtual Legacy Wire (VLW) Messages The PCH supports VLW messages as alternative method of conveying the status of the following legacy sideband interface signals to the processor: * A20M#, INTR, SMI#, INIT#, NMI Note: IGNNE# VLW message is not required to be generated by the PCH as it is internally emulated by the processor. VLW are inbound messages to the processor. They are communicated using Vendor Defined Message over the DMI link. Legacy processor signals can only be delivered using VLW in the PCH. Delivery of legacy processor signals (A20M#, INTR, SMI#, INIT# or NMI) using I/O APIC controller is not supported. 154 Datasheet Functional Description 5.14 Power Management 5.14.1 Features * Support for Advanced Configuration and Power Interface, Version 4.0a (ACPI) providing power and thermal management -- ACPI 24-Bit Timer SCI and SMI# Generation * PCI PME# signal for Wake Up from Low-Power states * System Sleep State Control -- ACPI S3 state - Suspend to RAM (STR) -- ACPI S4 state - Suspend-to-Disk (STD) -- ACPI G2/S5 state - Soft Off (SOFF) -- Power Failure Detection and Recovery -- Deep Sx * Intel Management Engine (Intel ME) Power Management Support -- Wake events from the Intel Management Engine (enabled from all S-States including Catastrophic S5 conditions) 5.14.2 PCH and System Power States Table 5-22 shows the power states defined for PCH-based platforms. The state names generally match the corresponding ACPI states. Table 5-22. General Power States for Systems Using the PCH State/ Substates Datasheet Legacy Name / Description G0/S0/C0 Full On: Processor operating. Individual devices may be shut down or be placed into lower power states to save power. G0/S0/Cx Cx State: Cx states are processor power states within the S0 system state that provide for various levels of power savings. The processor initiates C-state entry and exit while interacting with the PCH. The PCH will base its behavior on the processor state. G1/S1 S1: The PCH provides the S1 messages and the S0 messages on a wake event. It is preferred for systems to use C-states than S1. G1/S3 Suspend-To-RAM (STR): The system context is maintained in system DRAM, but power is shut off to non-critical circuits. Memory is retained and refreshes continue. All external clocks stop except RTC. G1/S4 Suspend-To-Disk (STD): The context of the system is maintained on the disk. All power is then shut off to the system except for the logic required to resume. G2/S5 Soft Off (SOFF): System context is not maintained. All power is shut off except for the logic required to restart. A full boot is required when waking. Deep Sx Deep Sx: An optional low power state where system context may or may not be maintained depending upon entry condition. All power is shut off except for minimal logic that allows exiting Deep Sx. If Deep Sx state was entered from S3 state, then the resume path will place system back into S3. If Deep Sx state was entered from S4 state, then the resume path will place system back into S4. If Deep Sx state was entered from S5 state, then the resume path will place system back into S5. G3 Mechanical OFF (M-Off): System context not maintained. All power is shut off except for the RTC. No "Wake" events are possible. This state occurs if the user removes the main system batteries in a mobile system, turns off a mechanical switch, or if the system power supply is at a level that is insufficient to power the "waking" logic. When system power returns, transition will depend on the state just prior to the entry to G3 and the AFTERG3_EN bit in the GEN_PMCON_3 register (D31:F0, offset A4). Refer to Table 5-29 for more details. 155 Functional Description Table 5-23 shows the transitions rules among the various states. Transitions among the various states may appear to temporarily transition through intermediate states. For example, in going from S0 to S3, it may appear to pass through the G1/S1 states. These intermediate transitions and states are not listed in the table. Table 5-23. State Transition Rules for the PCH Present State Transition Trigger G0/S0/C0 * * * * G0/S0/Cx * DMI Msg * Power Button Override3 * Mechanical Off/Power Failure * G0/S0/C0 * S5 * G3 G1/S1 or G1/S3 * Any Enabled Wake Event * Power Button Override3 * Conditions met as described in Section 5.14.7.6.1 and Section 5.14.7.6.2 * Mechanical Off/Power Failure * * * * * Any Enabled Wake Event * G0/S0/C02 G1/S4 DMI Msg SLP_EN bit set Power Button Override3 Mechanical Off/Power Failure Next State * Power Button Override3 * Conditions met as described in Section 5.14.7.6.1 and Section 5.14.7.6.2 G2/S5 G2/Deep Sx * * * * G0/S0/Cx G1/Sx or G2/S5 state G2/S5 G3 G0/S0/C02 G2/S5 Deep Sx G3 * G2/S5 * Deep Sx * Mechanical Off/Power Failure * G3 * Any Enabled Wake Event * G0/S0/C02 * Conditions met as described in Section 5.14.7.6.1 and Section 5.14.7.6.2 * Deep Sx * Mechanical Off/Power Failure * G3 * Any Enabled Wake Event * ACPRESENT Assertion * Mechanical Off/Power Failure * G0/S0/C02 * G1/S3, G1/S4 or G2/S5 (see Section 5.14.7.6.2) * G3 * Power Returns * S0/C0 (reboot) or G2/S54 (stay off until power button pressed or other wake event)1,2 G3 Notes: 1. Some wake events can be preserved through power failure. 2. Transitions from the S1-S5 or G3 states to the S0 state are deferred until BATLOW# is inactive in mobile configurations. 3. Includes all other applicable types of events that force the host into and stay in G2/S5. 4. If the system was in G1/S4 before G3 entry, then the system will go to S0/C0 or G1/S4. 156 Datasheet Functional Description 5.14.3 System Power Planes The system has several independent power planes, as described in Table 5-24. When a particular power plane is shut off, it should go to a 0 V level. Table 5-24. System Power Plane 5.14.4 Plane Controlled By Processor SLP_S3# signal The SLP_S3# signal can be used to cut the power to the processor completely. Description Main SLP_S3# signal When SLP_S3# goes active, power can be shut off to any circuit not required to wake the system from the S3 state. Since the S3 state requires that the memory context be preserved, power must be retained to the main memory. The processor, devices on the PCI bus, LPC I/F, and graphics will typically be shut off when the Main power plane is off, although there may be small subsections powered. Memory SLP_S4# signal SLP_S5# signal When SLP_S4# goes active, power can be shut off to any circuit not required to wake the system from the S4. Since the memory context does not need to be preserved in the S4 state, the power to the memory can also be shut down. When SLP_S5# goes active, power can be shut off to any circuit not required to wake the system from the S5 state. Since the memory context does not need to be preserved in the S5 state, the power to the memory can also be shut. Intel(R) ME SLP_A# LAN SLP_LAN# This signal is asserted in Sx/Moff when both host and Intel ME WoL are not supported. This signal can be use to control power to the Intel GbE PHY. Suspend Well SLP_SUS# This signal is asserted when the Sus rails can be externally shut off for enhanced power saving. DEVICE[n] Implementation Specific Individual subsystems may have their own power plane. For example, GPIO signals may be used to control the power to disk drives, audio amplifiers, or the display screen. This signal is asserted when the manageability platform goes to M-Off. Depending on the platform, this pin may be used to control the Intel Management Engine power planes, LAN subsystem power, and the SPI flash power. SMI# / SCI Generation Upon any enabled SMI event taking place while the End of SMI (EOS) bit is set, the PCH will clear the EOS bit and assert SMI to the processor, which will cause it to enter SMM space. SMI assertion is performed using a Virtual Legacy Wire (VLW) message. Prior system generations (those based upon legacy processors) used an actual SMI# pin. Once the SMI VLW has been delivered, the PCH takes no action on behalf of active SMI events until Host software sets the End of SMI (EOS) bit. At that point, if any SMI events are still active, the PCH will send another SMI VLW message. The SCI is a level-mode interrupt that is typically handled by an ACPI-aware operating system. In non-APIC systems (which is the default), the SCI IRQ is routed to one of the 8259 interrupts (IRQ 9, 10, or 11). The 8259 interrupt controller must be programmed to level mode for that interrupt. In systems using the APIC, the SCI can be routed to interrupts 9, 10, 11, 20, 21, 22, or 23. The interrupt polarity changes depending on whether it is on an interrupt shareable with a PIRQ or not (see Section 12.1.14). The interrupt remains asserted until all SCI sources are removed. Datasheet 157 Functional Description Table 5-25 shows which events can cause an SMI and SCI. Some events can be programmed to cause either an SMI or SCI. The usage of the event for SCI (instead of SMI) is typically associated with an ACPI-based system. Each SMI or SCI source has a corresponding enable and status bit. Table 5-25. Causes of SMI and SCI (Sheet 1 of 3) Cause SCI SMI Additional Enables Where Reported PME# Yes Yes PME_EN=1 PME_STS PME_B0 (Internal, Bus 0, PME-Capable Agents) Yes Yes PME_B0_EN=1 PME_B0_STS PCI Express* PME Messages Yes Yes PCI_EXP_EN=1 (Not enabled for SMI) PCI_EXP_STS PCI Express Hot-Plug Message Yes Yes HOT_PLUG_EN=1 (Not enabled for SMI) HOT_PLUG_STS Power Button Press Yes Yes PWRBTN_EN=1 PWRBTN_STS Power Button Override (Note 7) Yes No None PRBTNOR_STS RTC Alarm Yes Yes RTC_EN=1 RTC_STS Ring Indicate Yes Yes RI_EN=1 RI_STS ACPI Timer overflow (2.34 sec.) Yes Yes TMROF_EN=1 TMROF_STS Any GPI[15:0] Yes Yes GPI[x]_Route=10; GPI[x]_EN=1 (SCI) GPI[x]_Route=01; ALT_GPI[x]_SMI_EN=1 (SMI) GPI[x]_STS ALT_GPI[x]_SMI_STS GPIO[27] Yes Yes GP27_EN=1 GP27_STS TCO SCI Logic Yes No TCOSCI_EN=1 TCOSCI_STS GPIO[17] Yes Yes GPI[17] Route = 10 GP17_EN=1 (SCI); GPI[17]_Route=01 ALT_GP17_SMI_EN=1 (SMI) GP17_STS ALT_GPI17_SMI_STS GPIO[19] Yes Yes GPI[19] Route = 10 GP19_EN=1 (SCI); GPI[19]_Route=01 ALT_GP19_SMI_EN=1 (SMI) GP19_STS ALT_GPI19_SMI_STS GPIO[21] Yes Yes GPI[21] Route=10 GP21_EN=1 (SCI); GPI[21]_Route=01 ALT_GP21_SMI_EN=1 (SMI) GP21_STS ALT_GPI21_SMI_STS GPIO[22] Yes Yes GPI[22] Route = 10 GP22_EN=1 (SCI); GPI[22]_Route=01 ALT_GP22_SMI_EN=1 (SMI) GP22_STS ALT_GPI22_SMI_STS GPIO[43] Yes Yes GPI[43] Route = 10 GP43_EN=1 (SCI); GPI[43]_Route=01 ALT_GP43_SMI_EN=1 (SMI) GP43_STS ALT_GPI43_SMI_STS 158 Datasheet Functional Description Table 5-25. Causes of SMI and SCI (Sheet 2 of 3) Cause SCI SMI Additional Enables Where Reported GPIO[56] Yes Yes GPI[56] Route = 10 GP56_EN=1 (SCI); GPI[56]_Route=01 ALT_GP56_SMI_EN=1 (SMI) GP56_STS ALT_GPI56_SMI_STS GPIO[57] Yes Yes GPI[57] Route = 10 GP57_EN=1 (SCI); GPI[57]_Route=01 ALT_GP57_SMI_EN=1 (SMI) GP57_STS ALT_GPI57_SMI_STS GPIO[60] Yes Yes GPI[60] Route = 10 GP60_EN=1 (SCI); GPI[60]_Route=01 ALT_GP60_SMI_EN=1 (SMI) GP60_STS ALT_GPI60_SMI_STS TCO SCI message from processor Yes No None DMISCI_STS TCO SMI Logic No Yes TCO_EN=1 TCO_STS TCO SMI - - TCO TIMEROUT TCO SMI - OS writes to TCO_DAT_IN No Yes None NEWCENTURY_STS TCO SMI No Yes None TIMEOUT No Yes None SW_TCO_SMI register - Message from processor No Yes None DMISMI_STS TCO SMI - NMI occurred (and NMIs mapped to SMI) No Yes NMI2SMI_EN=1 NMI2SMI_STS TCO SMI TCO SMI - INTRUDER# signal goes active TCO SMI - Change of the BIOSWE (D31:F0:DCh, Bit 0) bit from 0 to 1 - Write attempted to BIOS No Yes INTRD_SEL=10 INTRD_DET No Yes BLE=1 BIOSWR_STS No Yes BIOSWE=1 BIOSWR_STS BIOS_RLS written to Yes No GBL_EN=1 GBL_STS GBL_RLS written to No Yes BIOS_EN=1 BIOS_STS Write to B2h register No Yes APMC_EN = 1 APM_STS Periodic timer expires No Yes PERIODIC_EN=1 PERIODIC_STS TCO SMI 64 ms timer expires No Yes SWSMI_TMR_EN=1 SWSMI_TMR_STS Enhanced USB Legacy Support Event No Yes LEGACY_USB2_EN = 1 LEGACY_USB2_STS Enhanced USB Intel Specific Event No Yes INTEL_USB2_EN = 1 INTEL_USB2_STS Serial IRQ SMI reported No Yes None SERIRQ_SMI_STS Device monitors match address in its range No Yes None SMBus Host Controller No Yes SMB_SMI_EN Host Controller Enabled DEVTRAP_STS SMBus host status reg. SMBus Slave SMI message No Yes None SMBUS_SMI_STS SMBus SMBALERT# signal active No Yes None SMBUS_SMI_STS SMBus Host Notify message received No Yes HOST_NOTIFY_INTREN SMBUS_SMI_STS HOST_NOTIFY_STS (Mobile Only) BATLOW# assertion Yes Yes BATLOW_EN=1 BATLOW_STS Access microcontroller 62h/66h No Yes MCSMI_EN MCSMI_STS SLP_EN bit written to 1 No Yes SLP_SMI_EN=1 SLP_SMI_STS SPI Command Completed No Yes None SPI_STS Software Generated GPE Yes Yes SWGPE_EN=1 SWGPE_STS Datasheet 159 Functional Description Table 5-25. Causes of SMI and SCI (Sheet 3 of 3) Cause SCI SMI Additional Enables Where Reported USB Per-Port Registers Write Enable bit changes to 1 No Yes INTEL_USB2_EN=1, Write_Enable_SMI_Enable=1 INTEL_USB2_STS, Write Enable Status GPIO Lockdown Enable bit changes from `1' to `0' No Yes GPIO_UNLOCK_SMI_EN=1 GPIO_UNLOCK_SMI_STS Wake Alarm Device Timer Yes Yes WADT_EN WADT_STS Notes: 1. SCI_EN must be 1 to enable SCI, except for BIOS_RLS. SCI_EN must be 0 to enable SMI. 2. SCI can be routed to cause interrupt 9:11 or 20:23 (20:23 only available in APIC mode). 3. GBL_SMI_EN must be 1 to enable SMI. 4. EOS must be written to 1 to re-enable SMI for the next 1. 5. The PCH must have SMI fully enabled when the PCH is also enabled to trap cycles. If SMI is not enabled in conjunction with the trap enabling, then hardware behavior is undefined. 6. Only GPI[15:0] may generate an SMI or SCI. 7. When a power button override first occurs, the system will transition immediately to S5. The SCI will only occur after the next wake to S0 if the residual status bit (PRBTNOR_STS) is not cleared prior to setting SCI_EN. 8. GBL_STS being set will cause an SCI, even if the SCI_EN bit is not set. Software must take great care not to set the BIOS_RLS bit (which causes GBL_STS to be set) if the SCI handler is not in place. 5.14.4.1 PCI Express* SCI PCI Express ports and the processor (using DMI) have the ability to cause PME using messages. When a PME message is received, the PCH will set the PCI_EXP_STS bit. If the PCI_EXP_EN bit is also set, the PCH can cause an SCI using the GPE1_STS register. 5.14.4.2 PCI Express* Hot-Plug PCI Express has a Hot-Plug mechanism and is capable of generating a SCI using the GPE1 register. It is also capable of generating an SMI. However, it is not capable of generating a wake event. 5.14.5 C-States PCH-based systems implement C-states by having the processor control the states. The chipset exchanges messages with the processor as part of the C-state flow, but the chipset does not directly control any of the processor impacts of C-states, such as voltage levels or processor clocking. In addition to the messages, the PCH also provides additional information to the processor using a sideband pin (PMSYNCH). All of the legacy C-state related pins (STPCLK#, STP_CPU#, DPRSLP#, DPRSLPVR#, and so on) do not exist on the PCH. 5.14.6 Dynamic 33 MHz Clock Control (Mobile Only) The 33 MHz clock can be dynamically controlled independent of any other low-power state. This control is accomplished using the CLKRUN# protocol and is transparent to software. The Dynamic 33MHz Clock control is handled using the following signal: * CLKRUN#: Used by LPC peripherals or other legacy devices to request the system 33 MHz clock to run 160 Datasheet Functional Description 5.14.6.1 Conditions for Checking the 33 MHz Clock When there is a lack of activity, the PCH has the capability to stop the 33 MHz clocks to conserve power. "Clock activity" is defined as any activity that would require the 33 MHz clock to be running. Any of the following conditions will indicate that it is not okay to stop the 33 MHz clock: * Cycles on LPC * SERIRQ activity Behavioral Description When there is a lack of activity (as defined above) for ninety 33 MHz clock cycles, the PCH de-asserts (drive high) CLKRUN# for 1 clock and then tri-states the signal. 5.14.6.2 Conditions for Maintaining the 33MHz Clock LPC or any other devices that wish to maintain the 33 MHz clock running will observe the CLKRUN# signal de-asserted, and then must re-assert if (drive it low) within 92 clocks. * When the PCH has tri-stated the CLKRUN# signal after de-asserting it, the PCH then checks to see if the signal has been re-asserted (externally). * After observing the CLKRUN# signal asserted for 1 clock, the PCH again starts asserting the signal. * If an internal device needs the PCI bus, the PCH asserts the CLKRUN# signal. 5.14.6.3 Conditions for Stopping the 33MHz Clock * If no device drives CLKRUN# low within 93 clock cycles after it has been deasserted, the PCH will stop the 33 MHz clocks. 5.14.6.4 Conditions for Re-Starting the 33MHz Clock * A peripheral asserts CLKRUN# to indicate that it needs the 33MHz clock re-started. * Observing the CLKRUN# signal asserted externally for 1 (free running) clock, the PCH again starts driving CLKRUN# asserted. If an internal source requests the clock to be re-started, the PCH re-asserts CLKRUN#, then the PCH will start the 33 MHz clocks. 5.14.6.5 LPC Devices and CLKRUN# If an LPC device (of any type) needs the 33 MHz clock, such as for LPC DMA or LPC serial interrupt, then it can assert CLKRUN#. LPC devices running DMA or bus master cycles will not need to assert CLKRUN#, since the PCH asserts it on their behalf. The LDRQ# inputs are ignored by the PCH when the 33MHz clock is stopped to the LPC devices in order to avoid misinterpreting the request. Datasheet 161 Functional Description 5.14.7 Sleep States 5.14.7.1 Sleep State Overview The PCH directly supports different sleep states (S1-S5), which are entered by methods such as setting the SLP_EN bit or due to a Power Button press. The entry to the Sleep states is based on several assumptions: * The G3 state cannot be entered using any software mechanism. The G3 state indicates a complete loss of power. 5.14.7.2 Initiating Sleep State Sleep states (S1-S5) are initiated by: * Masking interrupts, turning off all bus master enable bits, setting the desired type in the SLP_TYP field, and then setting the SLP_EN bit. The hardware then attempts to gracefully put the system into the corresponding Sleep state. * Pressing the PWRBTN# Signal for more than 4 seconds to cause a Power Button Override event. In this case the transition to the S5 state is less graceful, since there are no dependencies on DMI messages from the processor or on clocks other than the RTC clock. * Assertion of the THRMTRIP# signal will cause a transition to the S5 state. This can occur when system is in S0 or S1 state. * Shutdown by integrated manageability functions (ASF / Intel(R) AMT) * Internal watchdog timer time-out events Table 5-26. Sleep Types Sleep Type 5.14.7.3 Comment S1 System lowers the processor's power consumption. No snooping is possible in this state. S3 The PCH asserts SLP_S3#. The SLP_S3# signal controls the power to non-critical circuits. Power is only retained to devices needed to wake from this sleeping state, as well as to the memory. S4 The PCH asserts SLP_S3# and SLP_S4#. The SLP_S4# signal shuts off the power to the memory subsystem. Only devices needed to wake from this state should be powered. S5 The PCH asserts SLP_S3#, SLP_S4# and SLP_S5#. Exiting Sleep States Sleep states (S1-S5) are exited based on Wake events. The Wake events forces the system to a full on state (S0), although some non-critical subsystems might still be shut off and have to be brought back manually. For example, the hard disk may be shut off during a sleep state and have to be enabled using a GPIO pin before it can be used. Upon exit from the PCH-controlled Sleep states, the WAK_STS bit is set. The possible causes of Wake Events (and their restrictions) are shown in Table 5-27. Note: 162 (Mobile Only) If the BATLOW# signal is asserted, the PCH does not attempt to wake from an S1-S5 state, nor will it exit from Deep Sx state, even if the power button is pressed. This prevents the system from waking when the battery power is insufficient to wake the system. Wake events that occur while BATLOW# is asserted are latched by the PCH, and the system wakes after BATLOW# is de-asserted. Datasheet Functional Description Table 5-27. Causes of Wake Events How Enabled Wake from S1, Sx Wake from Deep Sx Wake from S1, Sx After Power Loss (Note 1) Wake from "Reset" Types (Note 2) RTC Alarm Set RTC_EN bit in PM1_EN register. Yes Yes Yes No Power Button Always enabled as Wake event. Yes Yes Yes Yes GPI[15:0] GPIO17, GPIO19, GPIO21, GPIO22, GPIO43, GPIO56, GPIO57, GPIO60 GPE0_EN register Note: GPIs that are in the core well are not capable of waking the system from sleep states when the core well is not powered. Yes No No No GPIO27 (Intel LAN solution uses GPIO27 for PHY Wake) Set GP27_EN in GPE0_EN Register. Yes Yes Yes Yes LAN Will use PME#. Wake enable set with LAN logic. Yes No Yes No Set RI_EN bit in GPE0_EN register. Yes No Yes No Intel High Definition Audio Event sets PME_B0_STS bit; PM_B0_EN must be enabled. Can not wake from S5 state if it was entered due to power failure or power button override. Yes No Yes No Primary PME# PME_B0_EN bit in GPE0_EN register. Yes No Yes No Secondary PME# Set PME_EN bit in GPE0_EN register. Yes No Yes No PCI_EXP_WAKE# PCI_EXP_WAKE bit. (Note 3) Yes Yes Yes No SATA Set PME_EN bit in GPE0_EN register. (Note 4) Yes (S1 only) No Yes (S1 only) No PCI_EXP PME Message Must use the PCI Express* WAKE# pin rather than messages for wake from S3, S4, or S5. Yes (S1 only) No Yes (S1 only) No Cause RI# (R) SMBALERT# Always enabled as Wake event. Yes No Yes Yes SMBus Slave Wake Message (01h) Wake/SMI# command always enabled as a Wake event. Note: SMBus Slave Message can wake the system from S1- S5, as well as from S5 due to Power Button Override. Yes No Yes Yes SMBus Host Notify message received HOST_NOTIFY_WKEN bit SMBus Slave Command register. Reported in the SMB_WAK_STS bit in the GPEO_STS register. Yes No Yes Yes Intel(R) ME NonMaskable Wake Always enabled as a wake event. Yes No Yes Yes Integrated WoL Enable Override WoL Enable Override bit (in Configuration Space). Yes No Yes Yes Wake Alarm Device WADT_EN in GPE0_EN Yes Yes No No Notes: 1. This column represents what the PCH would honor as wake events but there may be enabling dependencies on the device side which are not enabled after a power loss. 2. Reset Types include: Power Button override, Intel ME initiated power button override, Intel ME initiated host partition reset with power down, Intel ME Watchdog Timer, SMBus unconditional power down, processor thermal trip, PCH catastrophic temperature event. Datasheet 163 Functional Description 3. 4. When the WAKE# pin is active and the PCI Express device is enabled to wake the system, the PCH will wake the platform. SATA can only trigger a wake event in S1, but if PME is asserted prior to S3/S4/S5 entry and software does not clear the PME_B0_STS, a wake event would still result. It is important to understand that the various GPIs have different levels of functionality when used as wake events. The GPIs that reside in the core power well can only generate wake events from sleep states where the core well is powered. Also, only certain GPIs are "ACPI Compliant," meaning that their Status and Enable bits reside in ACPI I/O space. Table 5-28 summarizes the use of GPIs as wake events. Table 5-28. GPI Wake Events GPI Power Well Wake From Notes GPI[7:0] Core S1 ACPI Compliant GPI[15:8] Suspend S1-S5 ACPI Compliant The latency to exit the various Sleep states varies greatly and is heavily dependent on power supply design, so much so that the exit latencies due to the PCH are insignificant. 5.14.7.4 PCI Express* WAKE# Signal and PME Event Message PCI Express ports can wake the platform from any sleep state (S1, S3, S4, or S5 or Deep Sx) using the WAKE# pin. WAKE# is treated as a wake event, but does not cause any bits to go active in the GPE_STS register. PCI Express ports and the processor (using DMI) have the ability to cause PME using messages. When a PME message is received, the PCH will set the PCI_EXP_STS bit. 5.14.7.5 Sx-G3-Sx, Handling Power Failures Depending on when the power failure occurs and how the system is designed, different transitions could occur due to a power failure. The AFTERG3_EN bit provides the ability to program whether or not the system should boot once power returns after a power loss event. If the policy is to not boot, the system remains in an S5 state (unless previously in S4). There are only three possible events that will wake the system after a power failure. 1. PWRBTN#: PWRBTN# is always enabled as a wake event. When RSMRST# is low (G3 state), the PWRBTN_STS bit is reset. When the PCH exits G3 after power returns (RSMRST# goes high), the PWRBTN# signal is already high (because VCCstandBy goes high before RSMRST# goes high) and the PWRBTN_STS bit is 0. 2. RI#: RI# does not have an internal pull-up. Therefore, if this signal is enabled as a wake event, it is important to keep this signal powered during the power loss event. If this signal goes low (active), when power returns the RI_STS bit is set and the system interprets that as a wake event. 3. RTC Alarm: The RTC_EN bit is in the RTC well and is preserved after a power loss. Like PWRBTN_STS the RTC_STS bit is cleared when RSMRST# goes low. The PCH monitors both PCH PWROK and RSMRST# to detect for power failures. If PCH PWROK goes low, the PWROK_FLR bit is set. If RSMRST# goes low, PWR_FLR is set. Note: 164 Although PME_EN is in the RTC well, this signal cannot wake the system after a power loss. PME_EN is cleared by RTCRST#, and PME_STS is cleared by RSMRST#. Datasheet Functional Description Table 5-29. Transitions Due to Power Failure State at Power Failure AFTERG3_EN bit Transition When Power Returns S0, S1, S3 1 0 S5 S0 S4 1 0 S4 S0 S5 1 0 S5 S0 Deep Sx 1 0 Deep Sx1 S0 Note: 1. Entry state to Deep Sx is preserved through G3 allowing resume from Deep Sx to take appropriate path (that is, return to S3, S4 or S5). 5.14.7.6 Deep Sx To minimize power consumption while in S3/S4/S5, the PCH supports a lower power, lower featured version of these power states known as Deep Sx. In the Deep Sx state, the Suspend wells are powered off, while the Deep Sx Well (DSW) remains powered. A limited set of wake events are supported by the logic located in the DSW. The Deep Sx capability and the SUSPWRDNACK pin functionality are mutually exclusive. 5.14.7.6.1 Entry Into Deep Sx A combination of conditions is required for entry into Deep Sx. All of the following must be met: 1. Intel ME in M-Off 2. AND either a or b as defined below: a. ((DPS4_EN_AC AND S4) OR (DPS5_EN_AC AND S5)) (desktop only) b. ((ACPRESENT = 0) AND ((DPS3_EN_DC AND S3) OR (DPS4_EN_DC AND S4) OR (DPS5_EN_DC AND S5))) Table 5-30. Supported Deep Sx Policy Configurations Configuration DPS3_EN_D C DPS3_EN_ AC DPS4_EN_D C DPS4_EN_ AC DPS5_EN_ DC DPS5_EN_ AC 1: Enabled in S5 when on Battery (ACPRESENT = 0) 0 0 0 0 1 0 2: Enabled in S5 (ACPRESENT not considered) (desktop only) 0 0 0 0 1 1 3: Enabled in S4 and S5 when on Battery (ACPRESENT = 0) 0 0 1 0 1 0 4: Enabled in S4 and S5 (ACPRESENT not considered) (desktop only 0 0 1 1 1 1 5: Enabled in S3, S4 and S5 when on Battery (ACPRESENT = 0) 1 0 1 0 1 0 6: Deep S3/S4/ S5 disabled 0 0 0 0 0 0 Datasheet 165 Functional Description The PCH also performs a SUSWARN#/SUSACK# handshake to ensure the platform is ready to enter Deep Sx. The PCH asserts SUSWARN# as notification that it is about to enter Deep Sx. Before the PCH proceeds and asserts SLP_SUS#, the PCH waits for SUSACK# to assert. 5.14.7.6.2 Exit from Deep Sx While in Deep Sx, the PCH monitors and responds to a limited set of wake events (RTC Alarm, Power Button, WAKE#, and GPIO27). Upon sensing an enabled Deep Sx wake event, the PCH brings up the Suspend well by de-asserting SLP_SUS#. Table 5-31. Deep Sx Wake Events Event Enable RTC Alarm RTC_DS_WAKE_DIS (RCBA+3318h:Bit 21) Power Button Always enabled GPIO27 GPIO27_EN (PMBASE+28h:Bit 35) PCIe WAKE# pin PCIEXP_WAK_DIS Wake Alarm Device WADT_EN ACPRESENT has some behaviors that are different from the other Deep Sx wake events. If the Intel ME has enabled ACPRESENT as a wake event, then it behaves just like any other Intel ME Deep Sx wake event. However, even if ACPRESENT wakes are not enabled, if the Host policies indicate that Deep Sx is only supported when on battery, then ACPRESENT going high will cause the PCH to exit Deep Sx. In this case, the Suspend wells gets powered up and the platform remains in S3/MOFF, S4/MOFF or S5/MOFF. If ACPRESENT subsequently drops (before any Host or Intel ME wake events are detected), the PCH will re-enter Deep Sx. 5.14.8 Event Input Signals and Their Usage The PCH has various input signals that trigger specific events. This section describes those signals and how they should be used. 5.14.8.1 PWRBTN# (Power Button) The PCH PWRBTN# signal operates as a "Fixed Power Button" as described in the Advanced Configuration and Power Interface, Version 2.0b. PWRBTN# signal has a 16 ms de-bounce on the input. The state transition descriptions are included in Table 5-32. The transitions start as soon as the PWRBTN# is pressed (but after the debounce logic), and does not depend on when the Power Button is released. Note: During the time that the SLP_S4# signal is stretched for the minimum assertion width (if enabled), the Power Button is not a wake event. Refer to the following Power Button Override Function section for further details. Table 5-32. Transitions Due to Power Button (Sheet 1 of 2) Present State 166 Event Transition/Action Comment S0/Cx PWRBTN# goes low SMI or SCI generated (depending on SCI_EN, PWRBTN_EN and GLB_SMI_EN) Software typically initiates a Sleep state S1-S5 PWRBTN# goes low Wake Event. Transitions to S0 state Standard wakeup G3 PWRBTN# pressed None No effect since no power Not latched nor detected Datasheet Functional Description Table 5-32. Transitions Due to Power Button (Sheet 2 of 2) Present State S0-S4 Event PWRBTN# held low for at least 4 consecutive seconds Transition/Action Unconditional transition to S5 state Comment No dependence on processor (DMI Messages) or any other subsystem Power Button Override Function If PWRBTN# is observed active for at least four consecutive seconds, the state machine should unconditionally transition to the G2/S5 state, regardless of present state (S0- S4), even if the PCH PWROK is not active. In this case, the transition to the G2/S5 state should not depend on any particular response from the processor (such as, DMI Messages), nor any similar dependency from any other subsystem. The PWRBTN# status is readable to check if the button is currently being pressed or has been released. The status is taken after the de-bounce, and is readable using the PWRBTN_LVL bit. Note: The 4-second PWRBTN# assertion should only be used if a system lock-up has occurred. The 4-second timer starts counting when the PCH is in a S0 state. If the PWRBTN# signal is asserted and held active when the system is in a suspend state (S1-S5), the assertion causes a wake event. Once the system has resumed to the S0 state, the 4-second timer starts. Note: During the time that the SLP_S4# signal is stretched for the minimum assertion width (if enabled by D31:F0:A4h Bit 3), the Power Button is not a wake event. As a result, it is conceivable that the user will press and continue to hold the Power Button waiting for the system to awake. Since a 4-second press of the Power Button is already defined as an Unconditional Power down, the power button timer will be forced to inactive while the power-cycle timer is in progress. Once the power-cycle timer has expired, the Power Button awakes the system. Once the minimum SLP_S4# power cycle expires, the Power Button must be pressed for another 4 to 5 seconds to create the Override condition to S5. Sleep Button The Advanced Configuration and Power Interface, Version 2.0b defines an optional Sleep button. It differs from the power button in that it only is a request to go from S0 to S1-S4 (not S5). Also, in an S5 state, the Power Button can wake the system, but the Sleep Button cannot. Although the PCH does not include a specific signal designated as a Sleep Button, one of the GPIO signals can be used to create a "Control Method" Sleep Button. See the Advanced Configuration and Power Interface, Version 2.0b for implementation details. 5.14.8.2 RI# (Ring Indicator) The Ring Indicator can cause a wake event (if enabled) from the S1-S5 states. Table 5-33 shows when the wake event is generated or ignored in different states. If in the G0/S0/Cx states, the PCH generates an interrupt based on RI# active, and the interrupt will be set up as a Break event. Datasheet 167 Functional Description Table 5-33. Transitions Due to RI# Signal Present State Event RI_EN Event S0 RI# Active X Ignored S1-S5 RI# Active 0 1 Ignored Wake Event Note: Filtering/Debounce on RI# will not be done in PCH. Can be in modem or external. 5.14.8.3 PME# (PCI Power Management Event) The PME# signal comes from a PCI Express* device to request that the system be restarted. The PME# signal can generate an SMI#, SCI, or optionally a Wake event. The event occurs when the PME# signal goes from high to low. No event is caused when it goes from low to high. There is also an internal PME_B0 bit. This is separate from the external PME# signal and can cause the same effect. 5.14.8.4 SYS_RESET# Signal When the SYS_RESET# pin is detected as active after the 16 ms debounce logic, the PCH attempts to perform a "graceful" reset, by waiting up to 25 ms for the SMBus to go idle. If the SMBus is idle when the pin is detected active, the reset occurs immediately; otherwise, the counter starts. If at any point during the count the SMBus goes idle the reset occurs. If, however, the counter expires and the SMBus is still active, a reset is forced upon the system even though activity is still occurring. Once the reset is asserted, it remains asserted for 5 to 6 ms regardless of whether the SYS_RESET# input remains asserted or not. It cannot occur again until SYS_RESET# has been detected inactive after the debounce logic, and the system is back to a full S0 state with PLTRST# inactive. If bit 3 of the CF9h I/O register is set, then SYS_RESET# will result in a full power cycle reset. 5.14.8.5 THRMTRIP# Signal If THRMTRIP# goes active, the processor is indicating an overheat condition, and the PCH immediately transitions to an S5 state, driving SLP_S3#, SLP_S4#, SLP_S5# low, and setting the CTS bit. The transition looks like a power button override. When a THRMTRIP# event occurs, the PCH will power down immediately without following the normal S0 -> S5 path. The PCH will immediately drive SLP_S3#, SLP_S4#, and SLP_S5# low after sampling THRMTRIP# active. If the processor is running extremely hot and is heating up, it is possible (although very unlikely) that components around it, such as the PCH, are no longer executing cycles properly. Therefore, if THRMTRIP# goes active, and the PCH is relying on state machine logic to perform the power down, the state machine may not be working, and the system will not power down. The PCH provides filtering for short low glitches on the THRMTRIP# signal in order to prevent erroneous system shut downs from noise. Glitches shorter than 25nsec are ignored. 168 Datasheet Functional Description During boot, THRMTRIP# is ignored until SLP_S3#, PWROK, and PLTRST# are all `1'. During entry into a powered-down state (due to S3, S4, S5 entry, power cycle reset, and so on) THRMTRIP# is ignored until either SLP_S3# = 0, or PCH PWROK = 0, or SYS_PWROK = 0. Note: A thermal trip event will: * Clear the PWRBTN_STS bit * Clear all the GPE0_EN register bits * Clear the SMB_WAK_STS bit only if SMB_SAK_STS was set due to SMBus slave receiving message and not set due to SMBAlert 5.14.9 ALT Access Mode Before entering a low power state, several registers from powered down parts may need to be saved. In the majority of cases, this is not an issue, as registers have read and write paths. However, several of the ISA compatible registers are either read only or write only. To get data out of write-only registers, and to restore data into read-only registers, the PCH implements an ALT access mode. If the ALT access mode is entered and exited after reading the registers of the PCH timer (8254), the timer starts counting faster (13.5 ms). The following steps listed below can cause problems: 1. BIOS enters ALT access mode for reading the PCH timer related registers. 2. BIOS exits ALT access mode. 3. BIOS continues through the execution of other needed steps and passes control to the operating system. After getting control in step #3, if the operating system does not reprogram the system timer again, the timer ticks may be happening faster than expected. For example Microsoft* MS-DOS* and its associated software assume that the system timer is running at 54.6 ms and as a result the time-outs in the software may be happening faster than expected. Operating systems (such as Microsoft Windows* 98 and Windows* 2000) reprogram the system timer and therefore do not encounter this problem. For other operating systems (such as Microsoft MS-DOS*), the BIOS should restore the timer back to 54.6 ms before passing control to the operating system. If the BIOS is entering ALT access mode before entering the suspend state it is not necessary to restore the timer contents after the exit from ALT access mode. Datasheet 169 Functional Description 5.14.9.1 Write Only Registers with Read Paths in ALT Access Mode The registers described in Table 5-34 have read paths in ALT access mode. The access number field in the table indicates which register will be returned per access to that port. Table 5-34. Write Only Registers with Read Paths in ALT Access Mode (Sheet 1 of 2) Restore Data Restore Data I/O Addr # of Rds Access 00h 2 1 DMA Chan 0 base address low byte 2 01h 02h 03h 04h 05h 06h 07h 08h 170 2 2 2 2 2 2 2 6 I/O Addr # of Rds Access 40h 7 1 Timer Counter 0 status, bits [5:0] DMA Chan 0 base address high byte 2 Timer Counter 0 base count low byte 1 DMA Chan 0 base count low byte 3 Timer Counter 0 base count high byte 2 DMA Chan 0 base count high byte 4 Timer Counter 1 base count low byte 1 DMA Chan 1 base address low byte 5 Timer Counter 1 base count high byte 2 DMA Chan 1 base address high byte 6 Timer Counter 2 base count low byte 1 DMA Chan 1 base count low byte 7 Timer Counter 2 base count high byte 2 DMA Chan 1 base count high byte 41h 1 Timer Counter 1 status, bits [5:0] 1 DMA Chan 2 base address low byte 42h 1 Timer Counter 2 status, bits [5:0] 2 DMA Chan 2 base address high byte 70h 1 Bit 7 = NMI Enable, Bits [6:0] = RTC Address 1 DMA Chan 2 base count low byte C4h 2 2 DMA Chan 2 base count high byte 1 DMA Chan 3 base address low byte 2 DMA Chan 3 base address high byte 1 DMA Chan 3 base count low byte 2 DMA Chan 3 base count high byte 1 DMA Chan 0-3 Command2 2 DMA Chan 0-3 Request 3 DMA Chan 0 Mode: Bits(1:0) = 00 4 DMA Chan 1 Mode: Bits(1:0) = 01 5 DMA Chan 2 Mode: Bits(1:0) = 10 6 DMA Chan 3 Mode: Bits(1:0) = 11. Data C6h C8h CAh CCh CEh 2 2 2 2 2 Data 1 DMA Chan 5 base address low byte 2 DMA Chan 5 base address high byte 1 DMA Chan 5 base count low byte 2 DMA Chan 5 base count high byte 1 DMA Chan 6 base address low byte 2 DMA Chan 6 base address high byte 1 DMA Chan 6 base count low byte 2 DMA Chan 6 base count high byte 1 DMA Chan 7 base address low byte 2 DMA Chan 7 base address high byte 1 DMA Chan 7 base count low byte 2 DMA Chan 7 base count high byte Datasheet Functional Description Table 5-34. Write Only Registers with Read Paths in ALT Access Mode (Sheet 2 of 2) Restore Data Restore Data I/O Addr # of Rds Access I/O Addr # of Rds Access 20h 12 1 PIC ICW2 of Master controller D0h 6 1 DMA Chan 4-7 Command2 2 3 PIC ICW3 of Master controller 2 DMA Chan 4-7 Request PIC ICW4 of Master controller 3 DMA Chan 4 Mode: Bits(1:0) = 00 4 PIC OCW1 of Master controller1 4 DMA Chan 5 Mode: Bits(1:0) = 01 5 PIC OCW2 of Master controller 5 DMA Chan 6 Mode: Bits(1:0) = 10 6 PIC OCW3 of Master controller 6 DMA Chan 7 Mode: Bits(1:0) = 11. 7 PIC ICW2 of Slave controller 8 PIC ICW3 of Slave controller 9 PIC ICW4 of Slave controller Data 10 PIC OCW1 of Slave controller1 11 PIC OCW2 of Slave controller 12 PIC OCW3 of Slave controller Data Notes: 1. The OCW1 register must be read before entering ALT access mode. 2. Bits 5, 3, 1, and 0 return 0. 5.14.9.2 PIC Reserved Bits Many bits within the PIC are reserved, and must have certain values written in order for the PIC to operate properly. Therefore, there is no need to return these values in ALT access mode. When reading PIC registers from 20h and A0h, the reserved bits shall return the values listed in Table 5-35. Table 5-35. PIC Reserved Bits Return Values 5.14.9.3 PIC Reserved Bits Value Returned ICW2(2:0) 000 ICW4(7:5) 000 ICW4(3:2) 00 ICW4(0) 0 OCW2(4:3) 00 OCW3(7) 0 OCW3(5) Reflects bit 6 OCW3(4:3) 01 Read Only Registers with Write Paths in ALT Access Mode The registers described in Table 5-36 have write paths to them in ALT access mode. Software restores these values after returning from a powered down state. These registers must be handled special by software. When in normal mode, writing to the base address/count register also writes to the current address/count register. Therefore, the base address/count must be written first, then the part is put into ALT access mode and the current address/count register is written. Datasheet 171 Functional Description Table 5-36. Register Write Accesses in ALT Access Mode I/O Address Register Write Value 08h DMA Status Register for Channels 0-3 D0h DMA Status Register for Channels 4-7 5.14.10 System Power Supplies, Planes, and Signals 5.14.10.1 Power Plane Control with SLP_S3#, SLP_S4#, SLP_S5#, SLP_A# and SLP_LAN# The SLP_S3# output signal can be used to cut power to the system core supply, since it only goes active for the Suspend-to-RAM state (typically mapped to ACPI S3). Power must be maintained to the PCH suspend well, and to any other circuits that need to generate Wake signals from the Suspend-to-RAM state. During S3 (Suspend-to-RAM) all signals attached to powered down plans will be tri-stated or driven low, unless they are pulled using a pull-up resistor. Cutting power to the core may be done using the power supply, or by external FETs on the motherboard. The SLP_S4# or SLP_S5# output signal can be used to cut power to the system core supply, as well as power to the system memory, since the context of the system is saved on the disk. Cutting power to the memory may be done using the power supply, or by external FETs on the motherboard. The SLP_S4# output signal is used to remove power to additional subsystems that are powered during SLP_S3#. SLP_S5# output signal can be used to cut power to the system core supply, as well as power to the system memory, since the context of the system is saved on the disk. Cutting power to the memory may be done using the power supply, or by external FETs on the motherboard. SLP_A# output signal can be used to cut power to the Intel Management Engine and SPI flash on a platform that supports the M3 state (for example, certain power policies in Intel(R) AMT). SLP_LAN# output signal can be used to cut power to the external Intel(R) GbE PHY LAN device. 5.14.10.2 SLP_S4# and Suspend-To-RAM Sequencing The system memory suspend voltage regulator is controlled by the Glue logic. The SLP_S4# signal should be used to remove power to system memory rather than the SLP_S5# signal. The SLP_S4# logic in the PCH provides a mechanism to fully cycle the power to the DRAM and/or detect if the power is not cycled for a minimum time. Note: 172 To use the minimum DRAM power-down feature that is enabled by the SLP_S4# Assertion Stretch Enable bit (D31:F0:A4h Bit 3), the DRAM power must be controlled by the SLP_S4# signal. Datasheet Functional Description 5.14.10.3 PWROK Signal When asserted, PWROK is an indication to the PCH that its core well power rails are powered and stable. PWROK can be driven asynchronously. When PCH PWROK is low, the PCH asynchronously asserts PLTRST#. PWROK must not glitch, even if RSMRST# is low. It is required that the power associated with PCIe* have been valid for 99 ms prior to PWROK assertion in order to comply with the 100 ms PCIe 2.0 specification on PLTRST# de-assertion. Note: SYS_RESET# is recommended for implementing the system reset button. This saves external logic that is needed if the PWROK input is used. Additionally, it allows for better handling of the SMBus and processor resets and avoids improperly reporting power failures. 5.14.10.4 BATLOW# (Battery Low) (Mobile Only) The BATLOW# input can inhibit waking from S3, S4, S5, and Deep Sx states if there is not sufficient power. It also causes an SMI if the system is already in an S0 state. 5.14.10.5 SLP_LAN# Pin Behavior The PCH controls the voltage rails into the external LAN PHY using the SLP_LAN# pin. * The LAN PHY is always powered when the Host and ME systems are running. -- SLP_LAN#='1' whenever SLP_S3#='1' or SLP_A#='1'. * If the LAN PHY is required by ME in Sx/M-Off or Deep Sx, ME must configure SLP_LAN#='1' irrespective of the power source and the destination power state. ME must be powered at least once after G3 to configure this. * If the LAN PHY is required after a G3 transition, the host BIOS must set AG3_PP_EN (B0:D31:F0:A2h bit 12). * If the LAN PHY is required in Sx/M-Off, the host BIOS must set SX_PP_EN (B0:D31:F0:A2h bit 11). * If the LAN PHY is required in Deep Sx, the host BIOS must keep DSX_PP_DIS (B0:D31:F0:A2h bit 13) cleared. * If the LAN PHY is not required if the source of power is battery, the host BIOS must set DC_PP_DIS (B0:D31:F0:A2h bit 14). Note: ME configuration of SLP_LAN# in Sx/M-Off and Deep Sx is dependant on ME power policy configuration. The following flow chart shows how a decision is made to drive SLP_LAN# every time its policy needs to be evaluated. Datasheet 173 Functional Description Figure 5-7. Conceptual Diagram of SLP_LAN# State Transition Change (Sx or Mx) or ACPRESENT change S0 or Sx/M3 or ME configure WOL Enabled YES SLP_LAN#=1 NO After G3 NO YES NO AG3_PP_EN=1 Sx_PP_EN=1 NO SLP_LAN#=0 YES NO ACPRESENT or not(DC_PP_DIS) YES YES SLP_LAN#=0 YES Going to DeepSx and DSX_PP_DIS NO AG3_PP_EN = After G3 PHY Power Enable SX_PP_EN = SX PHY Power Enable (Regular SX entry) DC_PP_DIS = On DC PHY Power Disable DSX_PP_DIS = In Deep_SX PHY Power Disable SLP_LAN#=1 174 Datasheet Functional Description 5.14.10.6 SLP_WLAN# Pin Behavior The PCH controls the voltage rails into the external wireless LAN PHY using the SLP_WLAN# pin. * The wireless LAN PHY is always powered when the Host is running. -- SLP_WLAN#='1' whenever SLP_S3#='1'. * If Wake on Wireless LAN (WoWLAN) is required from S3/S4/S5 states, the host BIOS must set HOST_WLAN_PP_EN (RCBA+3318h bit 4). * If ME has access to the Wireless LAN device -- The Wireless LAN device must always be powered as long as Intel ME is powered. SLP_WLAN#='1' whenever SLP_A#='1'. -- If Wake on Wireless LAN (WoWLAN) is required from M-Off state, Intel ME will configure SLP_WLAN#='1' in Sx/M-Off. Intel ME configuration of SLP_WLAN# in Sx/M-Off is dependant on Intel ME power policy configuration. 5.14.10.7 SUSPWRDNACK/SUSWARN#/GPIO30 Steady State Pin Behavior The following tables summarize SUSPWRDNACK/SUSWARN#/GPIO30 pin behavior. Table 5-37. SUSPWRDNACK/SUSWARN#/GPIO30 Pin Behavior Topic Deep Sx Support GPIO30 Setting Pin Value in S0 Pin Value in Sx/ M-Off Pin Value in Sx/M3 Pin Value in Deep Sx SUSPWRDNACK Not Support Native 0 Depends on ME power package and source (note 1) 0 OFF SUSWARN# Support GPIO30 Don't Care Native 1 1 (note 2) 1 OFF IN High-Z High-Z High-Z OFF Don't Care OUT Depends on GPIO30 output data value Depends on GPIO30 output data value Depends on GPIO30 output data value OFF Notes: 1. PCH will drive SPDA pin based on ME power policy configuration. 2. If entering Deep Sx, pin will assert and become undriven ("Off") when suspend well drops upon Deep Sx entry. Table 5-38. SUSPWRDNACK during Reset Note: Datasheet PIC Reserved Bits Value Returned Power Cycle Reset 0 Global Reset 0 Straight to S5 PCH initially drive to `0' and then drive per ME power policy configuration. See Table 5-39. 175 Functional Description 5.14.10.8 RTCRST# and SRTCRST# RTCRST# is used to reset PCH registers in the RTC Well to their default value. If a jumper is used on this pin, it should only be pulled low when system is in the G3 state and then replaced to the default jumper position. Upon booting, BIOS should recognize that RTCRST# was asserted and clear internal PCH registers accordingly. It is imperative that this signal not be pulled low in the S0 to S5 states. SRTCRST# is used to reset portions of the Intel Management Engine and should not be connected to a jumper or button on the platform. The only time this signal gets asserted (driven low in combination with RTCRST#) should be when the coin cell battery is removed or not installed and the platform is in the G3 state. Pulling this signal low independently (without RTCRST# also being driven low) may cause the platform to enter an indeterminate state. Similar to RTCRST#, it is imperative that SRTCRST# not be pulled low in the S0 to S5 states. See Figure 2-2 which demonstrates the proper circuit connection of these pins. 5.14.11 Legacy Power Management Theory of Operation Instead of relying on ACPI software, legacy power management uses BIOS and various hardware mechanisms. The scheme relies on the concept of detecting when individual subsystems are idle, detecting when the whole system is idle, and detecting when accesses are attempted to idle subsystems. However, the operating system is assumed to be at least APM enabled. Without APM calls, there is no quick way to know when the system is idle between keystrokes. The PCH does not support burst modes. 5.14.11.1 APM Power Management (Desktop Only) The PCH has a timer that, when enabled by the 1MIN_EN bit in the SMI Control and Enable register, generates an SMI once per minute. The SMI handler can check for system activity by reading the DEVTRAP_STS register. If none of the system bits are set, the SMI handler can increment a software counter. When the counter reaches a sufficient number of consecutive minutes with no activity, the SMI handler can then put the system into a lower power state. If there is activity, various bits in the DEVTRAP_STS register will be set. Software clears the bits by writing a 1 to the bit position. The DEVTRAP_STS register allows for monitoring various internal devices, or Super I/O devices (SP, PP, FDC) on LPC, keyboard controller accesses, or audio functions on LPC. 5.14.11.2 Mobile APM Power Management (Mobile Only) In mobile systems, there are additional requirements associated with device power management. To handle this, the PCH has specific SMI traps available. The following algorithm is used: 1. The periodic SMI timer checks if a device is idle for the require time. If so, it puts the device into a low-power state and sets the associated SMI trap. 2. When software (not the SMI handler) attempts to access the device, a trap occurs (the cycle does not really go to the device and an SMI is generated). 3. The SMI handler turns on the device and turns off the trap. 176 Datasheet Functional Description 4. The SMI handler exits with an I/O restart. This allows the original software to continue. 5.14.12 Reset Behavior When a reset is triggered, the PCH will send a warning message to the processor to allow the processor to attempt to complete any outstanding memory cycles and put memory into a safe state before the platform is reset. When the processor is ready, it will send an acknowledge message to the PCH. Once the message is received, the PCH asserts PLTRST#. The PCH does not require an acknowledge message from the processor to trigger PLTRST#. A global reset will occur after 4 seconds if an acknowledge from the processor is not received. When the PCH causes a reset by asserting PLTRST#, its output signals will go to their reset states as defined in Chapter 3. A reset in which the host platform is reset and PLTRST# is asserted is called a Host Reset or Host Partition Reset. Depending on the trigger, a host reset may also result in power cycling (see Table 5-39 for details). If a host reset is triggered and the PCH times out before receiving an acknowledge message from the processor, a Global Reset with power cycle will occur. A reset in which the host and Intel ME partitions of the platform are reset is called a Global Reset. During a Global Reset, all PCH functionality is reset except RTC Power Well backed information and Suspend well status, configuration, and functional logic for controlling and reporting the reset. Intel ME and Host power back up after the power cycle period. Straight to S5 is another reset type where all power wells that are controlled by the SLP_S3#, SLP_S4#, and SLP_A# pins, as well as SLP_S5# and SLP_LAN# (if pins are not configured as GPIOs), are turned off. All PCH functionality is reset, except RTC Power Well backed information and Suspend well status, configuration, and functional logic for controlling and reporting the reset. The host stays there until a valid wake event occurs. Table 5-39 shows the various reset triggers. Table 5-39. Causes of Host and Global Resets (Sheet 1 of 2) Host Reset without Power Cycle1 Host Reset with Power Cycle2 Global Reset with Power Cycle3 Write of 0Eh to CF9h (RST_CNT Register) No Yes No (Note 4) Write of 06h to CF9h (RST_CNT Register) Yes No No (Note 4) SYS_RESET# Asserted and CF9h (RST_CNT Register) Bit 3=0 Yes No No (Note 4) SYS_RESET# Asserted and CF9h (RST_CNT Register) Bit 3=1 No Yes No (Note 4) SMBus Slave Message received for Reset with Power Cycle No Yes No (Note 4) SMBus Slave Message received for Reset without Power Cycle Yes No No (Note 4) SMBus Slave Message received for unconditional Power Down No No No Trigger Datasheet Straight to S5 (Host Stays there) Yes 177 Functional Description Table 5-39. Causes of Host and Global Resets (Sheet 2 of 2) Host Reset without Power Cycle1 Host Reset with Power Cycle2 Global Reset with Power Cycle3 TCO Watchdog Timer reaches zero two times Yes No No (Note 4) Power Failure: PWROK signal goes inactive in S0/S1 or DPWROK drops No No Yes SYS_PWROK Failure: SYS_PWROK signal goes inactive in S0/S1 No No Yes Processor Thermal Trip (THRMTRIP#) causes transition to S5 and reset asserts No No No Yes PCH internal thermal sensors signals a catastrophic temperature condition No No No Yes Power Button 4 second override causes transition to S5 and reset asserts No No No Yes Special shutdown cycle from processor causes CF9h-like PLTRST# and CF9h (RST_CNT Register) Bit 3 = 1 No Yes No (Note 4) Special shutdown cycle from processor causes CF9h-like PLTRST# and CF9h (RST_CNT Register) Bit 3 = 0 Yes No No (Note 4) Intel(R) Management Engine Triggered Host Reset without power cycle Yes No No (Note 4) Intel Management Engine Triggered Host Reset with power cycle No Yes No (Note 4) Intel Management Engine Triggered Power Button Override No No No Yes Intel Management Engine Watchdog Timer Timeout No No No Yes Trigger Straight to S5 (Host Stays there) Intel Management Engine Triggered Global Reset No No Yes Intel Management Engine Triggered Host Reset with power down (host stays there) No Yes (Note 5) No (Note 4) PLTRST# Entry Time-out No No Yes S3/4/5 Entry Timeout No No No PROCPWRGD Stuck Low No No Yes Power Management Watchdog Timer No No No Yes Intel Management Engine Hardware Uncorrectable Error No No No Yes Yes Notes: 1. The PCH drops this type of reset request if received while the system is in S3/S4/S5. 2. PCH does not drop this type of reset request if received while system is in a software-entered S3/S4/S5 state. However, the PCH will perform the reset without executing the RESET_WARN protocol in these states. 3. The PCH does not send warning message to processor, reset occurs without delay. 4. Trigger will result in Global Reset with power cycle if the acknowledge message is not received by the PCH. 5. The PCH waits for enabled wake event to complete reset. 5.15 System Management (D31:F0) The PCH provides various functions to make a system easier to manage and to lower the Total Cost of Ownership (TCO) of the system. Features and functions can be augmented using external A/D converters and GPIO, as well as an external microcontroller. The following features and functions are supported by the PCH: * Processor present detection -- Detects if processor fails to fetch the first instruction after reset 178 Datasheet Functional Description * Various Error detection (such as ECC Errors) indicated by host controller -- Can generate SMI#, SCI, SERR, NMI, or TCO interrupt * Intruder Detect input -- Can generate TCO interrupt or SMI# when the system cover is removed -- INTRUDER# allowed to go active in any power state, including G3 * Detection of bad BIOS Flash (FWH or Flash on SPI) programming -- Detects if data on first read is FFh (indicates that BIOS flash is not programmed) Note: Voltage ID from the processor can be read using GPI signals. 5.15.1 Theory of Operation The System Management functions are designed to allow the system to diagnose failing subsystems. The intent of this logic is that some of the system management functionality can be provided without the aid of an external microcontroller. 5.15.1.1 Detecting a System Lockup When the processor is reset, it is expected to fetch its first instruction. If the processor fails to fetch the first instruction after reset, the TCO timer times out twice and the PCH asserts PLTRST#. 5.15.1.2 Handling an Intruder The PCH has an input signal, INTRUDER#, that can be attached to a switch that is activated by the system's case being open. This input has a two RTC clock debounce. If INTRUDER# goes active (after the debouncer), this will set the INTRD_DET bit in the TCO2_STS register. The INTRD_SEL bits in the TCO_CNT register can enable the PCH to cause an SMI# or interrupt. The BIOS or interrupt handler can then cause a transition to the S5 state by writing to the SLP_EN bit. The software can also directly read the status of the INTRUDER# signal (high or low) by clearing and then reading the INTRD_DET bit. This allows the signal to be used as a GPI if the intruder function is not required. If the INTRUDER# signal goes inactive some point after the INTRD_DET bit is written as a 1, then the INTRD_DET bit will go to a 0 when INTRUDER# input signal goes inactive. This is slightly different than a classic sticky bit, since most sticky bits would remain active indefinitely when the signal goes active and would immediately go inactive when a 1 is written to the bit. Note: The INTRD_DET bit resides in the PCH's RTC well, and is set and cleared synchronously with the RTC clock. Thus, when software attempts to clear INTRD_DET (by writing a 1 to the bit location) there may be as much as two RTC clocks (about 65 s) delay before the bit is actually cleared. Also, the INTRUDER# signal should be asserted for a minimum of 1 ms to ensure that the INTRD_DET bit will be set. Note: If the INTRUDER# signal is still active when software attempts to clear the INTRD_DET bit, the bit remains set and the SMI is generated again immediately. The SMI handler can clear the INTRD_SEL bits to avoid further SMIs. However, if the INTRUDER# signal goes inactive and then active again, there will not be further SMIs, since the INTRD_SEL bits would select that no SMI# be generated. Datasheet 179 Functional Description 5.15.1.3 Detecting Improper Flash Programming The PCH can detect the case where the BIOS flash is not programmed. This results in the first instruction fetched to have a value of FFh. If this occurs, the PCH sets the BAD_BIOS bit. The BIOS flash may reside in FWH or flash on the SPI bus. 5.15.1.4 Heartbeat and Event Reporting using SMLink/SMBus Heartbeat and event reporting using SMLink/SMBus is no longer supported. The Intel(R) AMT logic in the PCH can be programmed to generate an interrupt to the Intel Management Engine (Intel ME) when an event occurs. The Intel ME will poll the TCO registers to gather appropriate bits to send the event message to the Gigabit Ethernet controller, if the Intel ME is programmed to do so. 5.15.2 TCO Modes 5.15.2.1 TCO Legacy / Compatible Mode In TCO Legacy/Compatible mode, only the host SMBus is used. The TCO Slave is connected to the host SMBus internally by default. In this mode, the Intel ME SMBus controllers are not used and should be disabled by soft strap. Figure 5-8. TCO Legacy/Compatible Mode SMBus Configuration PCH TCO Legacy/Compatible Mode Intel ME SMBus Controller 3 X Intel ME SMBus Controller 2 X Intel ME SMBus Controller 1 X SPD (Slave) PCI/PCIe* Device uCtrl SMBus Host SMBus TCO Slave Legacy Sensors (Master or Slave with ALERT) 3rd Party NIC In TCO Legacy/Compatible mode the PCH can function directly with an external LAN controller or equivalent external LAN controller to report messages to a network management console without the aid of the system processor. This is crucial in cases where the processor is malfunctioning or cannot function due to being in a low-power state. Table 5-40 includes a list of events that will report messages to the network management console. 180 Datasheet Functional Description Table 5-40. Event Transitions that Cause Messages Event De-assertion? Comments INTRUDER# pin Yes No Must be in "S1 or hung S0" state THRM# pin Yes Yes Must be in "S1 or hung S0" state. The THRM# pin is isolated when the core power is off, thus preventing this event in S3-S5. Watchdog Timer Expired Yes No (NA) GPIO[11]/ SMBALERT# pin Yes Yes Must be in "S1 or hung S0" state BATLOW# Yes Yes Must be in "S1 or hung S0" state CPU_PWR_FLR Yes No "S1 or hung S0" state entered Note: 5.15.2.2 Assertion? "S1 or hung S0" state entered The GPIO11/SMBALERT# pin will trigger an event message (when enabled by the GPIO11_ALERT_DISABLE bit) regardless of whether it is configured as a GPI or not. Advanced TCO Mode The PCH supports the Advanced TCO mode in which SMLink0 and SMLink1 are used in addition to the host SMBus. See Figure 5-9 for more details. In this mode, the Intel ME SMBus controllers must be enabled by soft strap in the flash descriptor. SMLink0 is dedicated to integrated LAN use and when an Intel(R) GbE PHY LAN is connected to SMLink0, a soft strap must be set to indicate that the PHY is connected to SMLink0. The interface will be running at the frequency of up to 1 MHz depending on different factors such as board routing or bus loading when the Fast Mode is enabled using a soft strap. SMLink1 is dedicated to Embedded Controller (EC) or Baseboard Management Controller (BMC) use. In the case where a BMC is connected to SMLink1, the BMC communicates with the Intel ME through the Intel ME SMBus connected to SMLink1. The host and TCO slave communicate with BMC through SMBus. Datasheet 181 Functional Description Figure 5-9. Advanced TCO Mode PCH Intel ME SMBus Controller 3 Intel ME SMBus Controller 2 Intel ME SMBus Controller 1 Advanced TCO Mode EC or BMC SMLink1 Intel(R) I127LM/V SMLink0 SPD (Slave) PCIe* Device Host SMBus TCO Slave 5.16 SMBus Legacy Sensors (Master or Slave with ALERT) General Purpose I/O (D31:F0) The PCH contains up to 70 General Purpose Input/Output (GPIO) signals for Desktop PCH and 75 General Purpose Input/Output (GPIO) for Mobile PCH. Each GPIO can be configured as an input or output signal. The number of inputs and outputs varies depending on the configuration. Following is a brief summary of GPIO features. * Capability to mask Suspend well GPIOs from CF9h events (configured using GP_RST_SEL registers) * Added capability to program GPIO prior to switching to output 5.16.1 Power Wells Some GPIOs exist in the suspend power plane. Care must be taken to make sure GPIO signals are not driven high into powered-down planes. Some PCH GPIOs may be connected to pins on devices that exist in the core well. If these GPIOs are outputs, there is a danger that a loss of core power (PWROK low) or a Power Button Override event results in the PCH driving a pin to a logic 1 to another device that is powered down. 5.16.2 SMI#, SCI, and NMI Routing The routing bits for GPIO[15:0] allow an input to be routed to SMI#, SCI, NMI or none of these. A bit can be routed to either an SMI# or an SCI, but not both. 182 Datasheet Functional Description 5.16.3 Triggering GPIO[15:0] have "sticky" bits on the input. Refer to the GPE0_STS register and the ALT_GPI_SMI_STS register. As long as the signal goes active for at least 2 clock cycles, the PCH keeps the sticky status bit active. The active level can be selected in the GP_INV register. This does not apply to GPI_NMI_STS residing in GPIO I/O space. If the system is in an S0 or an S1 state, the GPI inputs are sampled at 33 MHz, so the signal only needs to be active for about 60 ns to be latched. In the S3-S5 states, the GPI inputs are sampled at 32.768 kHz, and thus must be active for at least 61 microseconds to be latched. Note: GPIs that are in the core well are not capable of waking the system from sleep states where the core well is not powered. If the input signal is still active when the latch is cleared, it will again be set. Another edge trigger is not required. This makes these signals "level" triggered inputs. 5.16.4 GPIO Registers Lockdown The following GPIO registers are locked down when the GPIO Lockdown Enable (GLE) bit is set. The GLE bit resides in D31:F0:GPIO Control (GC) register. * * * * * * * * * * * * * * Note: Offset Offset Offset Offset Offset Offset Offset Offset Offset Offset Offset Offset Offset Offset 00h: GPIO_USE_SEL[31:0] 04h: GP_IO_SEL[31:0] 0Ch: GP_LVL[31:0] 28h: GPI_NMI_EN[15:0] 2Ch: GPI_INV[31:0] 30h: GPIO_USE_SEL2[63:32] 34h: GPI_IO_SEL2[63:32] 38h: GP_LVL2[63:32] 40h: GPIO_USE_SEL3[95:64] 44h: GPI_IO_SEL3[95:64] 48h: GP_LVL3[95:64] 60h: GP_RST_SEL[31:0] 64h: GP_RST_SEL2[63:32] 68h: GP_RST_SEL3[95:64] All other GPIO registers not listed here are not to be locked by GLE. Once these registers are locked down, they become Read-Only registers and any software writes to these registers will have no effect. To unlock the registers, the GPIO Lockdown Enable (GLE) bit is required to be cleared to `0'. When the GLE bit changes from a `1' to a `0' a System Management Interrupt (SMI#) is generated if enabled. Once the GPIO_UNLOCK_SMI bit is set, it can not be changed until a PLTRST# occurs. This ensures that only BIOS can change the GPIO configuration. If the GLE bit is cleared by unauthorized software, BIOS will set the GLE bit again when the SMI# is triggered and these registers will continue to be locked down. 5.16.5 Serial POST Codes over GPIO The PCH adds the extended capability allowing system software to serialize POST or other messages on GPIO. This capability negates the requirement for dedicated diagnostic LEDs on the platform. Datasheet 183 Functional Description 5.16.5.1 Theory of Operation For the PCH generation POST code serialization logic will be shared with GPIO. These GPIOs will likely be shared with LED control offered by the Super I/O (SIO) component. Figure 5-10 shows a likely configuration. Figure 5-10. Serial Post over GPIO Reference Circuit V_3P3_STBY R PCH SIO LED Note: The pull-up value is based on the brightness required. The anticipated usage model is that either the PCH or the SIO can drive a pin low to turn off an LED. In the case of the power LED, the SIO would normally leave its corresponding pin in a high-Z state to allow the LED to turn on. In this state, the PCH can blink the LED by driving its corresponding pin low and subsequently tri-stating the buffer. The I/O buffer should not drive a `1' when configured for this functionality and should be capable of sinking 24 mA of current. An external optical sensing device can detect the on/off state of the LED. By externally post-processing the information from the optical device, the serial bit stream can be recovered. The hardware will supply a `sync' byte before the actual data transmission to allow external detection of the transmit frequency. The frequency of transmission should be limited to 1 transition every 1 s to ensure the detector can reliably sample the on/off state of the LED. To allow flexibility in pull-up resistor values for power optimization, the frequency of the transmission is programmable using the DRS field in the GP_GB_CMDSTS register. The serial bit stream is Manchester encoded. This choice of transmission ensures that a transition will be seen on every clock. The 1 or 0 data is based on the transmission happening during the high or low phase of the clock. As the clock will be encoded within the data stream, hardware must ensure that the Z0 and 0-Z transitions are glitch-free. Driving the pin directly from a flip-flop or through glitch-free logic are possible methods to meet the glitch-free requirement. A simplified hardware/software register interface provides control and status information to track the activity of this block. Software enabling the serial blink capability should implement an algorithm referenced below to send the serialized message on the enabled GPIO. 184 Datasheet Functional Description 1. Read the Go/Busy status bit in the GP_GB_CMDSTS register and verify it is cleared. This will ensure that the GPIO is idled and a previously requested message is still not in progress. 2. Write the data to serialize into the GP_GB_DATA register. 3. Write the DLS and DRS values into the GP_GB_CMDSTS register and set the Go bit. This may be accomplished using a single write. The reference diagram shows the LEDs being powered from the suspend supply. By providing a generic capability that can be used both in the main and the suspend power planes maximum flexibility can be achieved. A key point to make is that the PCH will not unintentionally drive the LED control pin low unless a serialization is in progress. System board connections utilizing this serialization capability are required to use the same power plane controlling the LED as the PCH GPIO pin. Otherwise, the PCH GPIO may float low during the message and prevent the LED from being controlled from the SIO. The hardware will only be serializing messages when the core power well is powered and the processor is operational. Care should be taken to prevent the PCH from driving an active `1' on a pin sharing the serial LED capability. Since the SIO could be driving the line to 0, having the PCH drive a 1 would create a high current path. A recommendation to avoid this condition involves choosing a GPIO defaulting to an input. The GP_SER_BLINK register should be set first before changing the direction of the pin to an output. This sequence ensures the open-drain capability of the buffer is properly configured before enabling the pin as an output. 5.16.5.2 Serial Message Format In order to serialize the data onto the GPIO, an initial state of high-Z is assumed. The SIO is required to have its LED control pin in a high-Z state as well to allow the PCH to blink the LED (refer to the reference diagram). The three components of the serial message include the sync, data, and idle fields. The sync field is 7 bits of `1' data followed by 1 bit of `0' data. Starting from the high-Z state (LED on) provides external hardware a known initial condition and a known pattern. In case one or more of the leading 1 sync bits are lost, the 1s followed by 0 provide a clear indication of `end of sync'. This pattern will be used to `lock' external sampling logic to the encoded clock. The data field is shifted out with the highest byte first (MSB). Within each byte, the most significant bit is shifted first (MSb). The idle field is enforced by the hardware and is at least 2 bit times long. The hardware will not clear the Busy and Go bits until this idle time is met. Supporting the idle time in hardware prevents time-based counting in BIOS as the hardware is immediately ready for the next serial code when the Go bit is cleared. The idle state is represented as a high-Z condition on the pin. If the last transmitted bit is a 1, returning to the idle state will result in a final 0-1 transition on the output Manchester data. Two full bit times of idle correspond to a count of 4 time intervals (the width of the time interval is controlled by the DRS field). The following waveform shows a 1-byte serial write with a data byte of 5Ah. The internal clock and bit position are for reference purposes only. The Manchester D is the resultant data generated and serialized onto the GPIO. Since the buffer is operating in open-drain mode the transitions are from high-Z to 0 and back. Datasheet 185 Functional Description Bit 7 6 5 4 3 2 1 0 Internal Clock Manchester D 8-bit sync field (1111_1110) 5.17 5A data byte 2 clk idle SATA Host Controller (D31:F2, F5) The SATA function in the PCH has three modes of operation to support different operating system conditions. In the case of Native IDE enabled operating systems, the PCH uses two controllers to enable all six ports of the bus. The first controller (Device 31: Function 2) supports ports 0 - 3 and the second controller (Device 31: Function 5) supports ports 4 and 5. When using a legacy operating system, only one controller (Device 31: Function 2) is available that supports ports 0 - 3. In AHCI or RAID mode, only one controller (Device 31: Function 2) is utilized enabling all six ports and the second controller (Device 31: Function 5) shall be disabled. The MAP register, Section 14.1.27, provides the ability to share PCI functions. When sharing is enabled, all decode of I/O is done through the SATA registers. Device 31, Function 1 (IDE controller) is hidden by software writing to the Function Disable Register (D31, F0, Offset F2h, bit 1), and its configuration registers are not used. The PCH SATA controllers feature six sets of interface signals (ports) that can be independently enabled or disabled (they cannot be tri-stated or driven low). Each interface is supported by an independent DMA controller. The PCH SATA controllers interact with an attached mass storage device through a register interface that is equivalent to that presented by a traditional IDE host adapter. The host software follows existing standards and conventions when accessing the register interface and follows standard command protocol conventions. Note: SATA interface transfer rates are independent of UDMA mode settings. SATA interface transfer rates will operate at the bus's maximum speed, regardless of the UDMA mode reported by the SATA device or the system BIOS. 5.17.1 SATA 6 Gb/s Support The PCH supports SATA 6 Gb/s transfers with all capable SATA devices. 5.17.2 SATA Feature Support Table 5-41. SATA Feature Support (Sheet 1 of 2) PCH (AHCI/RAID Disabled) PCH (AHCI/RAID Enabled) Native Command Queuing (NCQ) N/A Supported Auto Activate for DMA N/A Supported Feature 186 Datasheet Functional Description Table 5-41. SATA Feature Support (Sheet 2 of 2) PCH (AHCI/RAID Disabled) Feature PCH (AHCI/RAID Enabled) Hot-Plug Support N/A Supported Asynchronous Signal Recovery N/A Supported 6 Gb/s Transfer Rate Supported Supported ATAPI Asynchronous Notification N/A Supported Host and Link Initiated Power Management N/A Supported Supported Supported Staggered Spin-Up Command Completion Coalescing N/A N/A External SATA N/A Supported Table 5-42. SATA Features Feature Description Native Command Queuing (NCQ) Allows the device to reorder commands for more efficient data transfers Auto Activate for DMA Collapses a DMA Setup then DMA Activate sequence into a DMA Setup only Hot-Plug Support Allows for device detection without power being applied and ability to connect and disconnect devices without prior notification to the system Asynchronous Signal Recovery Provides a recovery from a loss of signal or establishing communication after Hot-Plug 6 Gb/s Transfer Rate Capable of data transfers up to 6 Gb/s ATAPI Asynchronous Notification A mechanism for a device to send a notification to the host that the device requires attention Host and Link Initiated Power Management Capability for the host controller or device to request Partial and Slumber interface power states Staggered Spin-Up Enables the host the ability to spin up hard drives sequentially to prevent power load problems on boot Command Completion Coalescing Reduces interrupt and completion overhead by allowing a specified number of commands to complete and then generating an interrupt to process the commands External SATA Technology that allows for an outside the box connection of up to 2 meters (when using the cable defined in SATA-IO) 5.17.3 Theory of Operation 5.17.3.1 Standard ATA Emulation The PCH contains a set of registers that shadow the contents of the legacy IDE registers. The behavior of the Command and Control Block registers, PIO, and DMA data transfers, resets, and interrupts are all emulated. Note: Datasheet The PCH will assert INTR when the master device completes the EDD command regardless of the command completion status of the slave device. If the master completes EDD first, an INTR is generated and BSY will remain '1' until the slave completes the command. If the slave completes EDD first, BSY will be '0' when the master completes the EDD command and asserts INTR. Software must wait for busy to clear (0) before completing an EDD command, as required by the ATA5 through ATA7 (T13) industry standards. 187 Functional Description 5.17.3.2 48-Bit LBA Operation The SATA host controller supports 48-bit LBA through the host-to-device register FIS when accesses are performed using writes to the task file. The SATA host controller will ensure that the correct data is put into the correct byte of the host-to-device FIS. There are special considerations when reading from the task file to support 48-bit LBA operation. Software may need to read all 16-bits. Since the registers are only 8-bits wide and act as a FIFO, a bit must be set in the device/control register, which is at offset 3F6h for primary and 376h for secondary (or their native counterparts). If software clears Bit 7 of the control register before performing a read, the last item written will be returned from the FIFO. If software sets Bit 7 of the control register before performing a read, the first item written will be returned from the FIFO. 5.17.4 SATA Swap Bay Support The PCH provides for basic SATA swap bay support using the PSC register configuration bits and power management flows. A device can be powered down by software and the port can then be disabled, allowing removal and insertion of a new device. Note: This SATA swap bay operation requires board hardware (implementation specific), BIOS, and operating system support. 5.17.5 Hot-Plug Operation The PCH supports Hot-Plug Surprise removal and Insertion Notification. An internal SATA port with a Mechanical Presence Switch can support PARTIAL and SLUMBER with Hot-Plug Enabled. Software can take advantage of power savings in the low power states while enabling Hot-Plug operation. Refer to chapter 7 of the AHCI specification for details. 5.17.6 Intel(R) Rapid Storage Technology (Intel RST(R)) Configuration The Intel Rapid Storage Technology (Intel RST) offers several diverse options for RAID (redundant array of independent disks) to meet the needs of the end user. AHCI support provides higher performance and alleviates disk bottlenecks by taking advantage of the independent DMA engines that each SATA port offers in the PCH. * RAID Level 0 performance scaling up to 6 drives, enabling higher throughput for data intensive applications such as video editing. * Data security is offered through RAID Level 1, which performs mirroring. * RAID Level 10 provides high levels of storage performance with data protection, combining the fault-tolerance of RAID Level 1 with the performance of RAID Level 0. By striping RAID Level 1 segments, high I/O rates can be achieved on systems that require both performance and fault-tolerance. RAID Level 10 requires 4 hard drives, and provides the capacity of two drives. * RAID Level 5 provides highly efficient storage while maintaining fault-tolerance on 3 or more drives. By striping parity, and rotating it across all disks, fault tolerance of any single drive is achieved while only consuming 1 drive worth of capacity. That is, a 3 drive RAID 5 has the capacity of 2 drives, or a 4 drive RAID 5 has the capacity of 3 drives. RAID 5 has high read transaction rates, with a medium write rate. RAID 5 is well suited for applications that require high amounts of storage while maintaining fault tolerance. 188 Datasheet Functional Description By using the PCH's built-in Intel Rapid Storage Technology, there is no loss of PCI resources (request/grant pair) or add-in card slot. Intel Rapid Storage Technology (Intel RST) functionality requires the following items: 1. 2. 3. 4. PCH SKU enabled for Intel Rapid Storage Technology (see Section 1.3) Intel Rapid Storage Technology RAID Option ROM must be on the platform Intel Rapid Storage Technology drivers, most recent revision. At least two SATA hard disk drives (minimum depends on RAID configuration). Intel Rapid Storage Technology is not available in the following configurations: 1. The SATA controller is in compatible mode. 2. The SATA controller is programmed in RAID mode, but the AIE bit (D31:F2:Offset 9Ch bit 7) is set to 1. 5.17.6.1 Intel(R) Rapid Storage Technology (Intel(R) RST) RAID Option ROM The Intel Rapid Storage Technology RAID Option ROM is a standard PnP Option ROM that is easily integrated into any System BIOS. When in place, it provides the following three primary functions: * Provides a text mode user interface that allows the user to manage the RAID configuration on the system in a pre-operating system environment. Its feature set is kept simple to keep size to a minimum, but allows the user to create and delete RAID volumes and select recovery options when problems occur. * Provides boot support when using a RAID volume as a boot disk. It does this by providing Int13 services when a RAID volume needs to be accessed by MS-DOS applications (such as NTLDR) and by exporting the RAID volumes to the System BIOS for selection in the boot order. * At each boot up, provides the user with a status of the RAID volumes and the option to enter the user interface by pressing CTRL-I. 5.17.7 Intel(R) Smart Response Technology Part of the Intel RST storage class driver feature set, Intel Smart Response Technology implements storage I/O caching to provide users with faster response times for things like system boot and application startup. On a traditional system, performance of these operations is limited by the hard drive, particularly when there may be other I/O intensive background activities running simultaneously, like system updates or virus scans. Intel Smart Response Technology accelerates the system response experience by putting frequently-used blocks of disk data on an SSD, providing dramatically faster access to user data than the hard disk alone can provide. The user sees the full capacity of the hard drive with the traditional single drive letter with overall system responsiveness similar to what an SSD-only system provides. See Section 1.3 for SKUs enabled for Intel Smart Response Technology. 5.17.8 Power Management Operation Power management of the PCH SATA controller and ports will cover operations of the host controller and the SATA wire. Datasheet 189 Functional Description 5.17.8.1 Power State Mappings The D0 PCI power management state for device is supported by the PCH SATA controller. SATA devices may also have multiple power states. From parallel ATA, three device states are supported through ACPI. They are: * D0 - Device is working and instantly available. * D1 - Device enters when it receives a STANdBY IMMEDIATE command. Exit latency from this state is in seconds * D3 - From the SATA device's perspective, no different than a D1 state, in that it is entered using the STANdBY IMMEDIATE command. However, an ACPI method is also called which will reset the device and then cut its power. Each of these device states are subsets of the host controller's D0 state. Finally, SATA defines three PHY layer power states, which have no equivalent mappings to parallel ATA. They are: * PHY READY - PHY logic and PLL are both on and active * Partial - PHY logic is powered, but in a reduced state. Exit latency is no longer than 10 ns * Slumber - PHY logic is powered, but in a reduced state. Exit latency can be up to 10 ms. Since these states have much lower exit latency than the ACPI D1 and D3 states, the SATA controller defines these states as sub-states of the device D0 state. 5.17.8.2 Power State Transitions 5.17.8.2.1 Partial and Slumber State Entry/Exit The partial and slumber states save interface power when the interface is idle. It would be most analogous to CLKRUN# (in power savings, not in mechanism), where the interface can have power saved while no commands are pending. The SATA controller defines PHY layer power management (as performed using primitives) as a driver operation from the host side, and a device proprietary mechanism on the device side. The SATA controller accepts device transition types, but does not issue any transitions as a host. All received requests from a SATA device will be ACKed. When an operation is performed to the SATA controller such that it needs to use the SATA cable, the controller must check whether the link is in the Partial or Slumber states, and if so, must issue a COM_WAKE to bring the link back online. Similarly, the SATA device must perform the same action. 5.17.8.2.2 Device D1, D3 States These states are entered after some period of time when software has determined that no commands will be sent to this device for some time. The mechanism for putting a device in these states does not involve any work on the host controller, other then sending commands over the interface to the device. The command most likely to be used in ATA/ATAPI is the "STANdBY IMMEDIATE" command. 190 Datasheet Functional Description 5.17.8.2.3 Host Controller D3HOT State After the interface and device have been put into a low power state, the SATA host controller may be put into a low power state. This is performed using the PCI power management registers in configuration space. There are two very important aspects to note when using PCI power management. 1. When the power state is D3, only accesses to configuration space are allowed. Any attempt to access the memory or I/O spaces will result in master abort. 2. When the power state is D3, no interrupts may be generated, even if they are enabled. If an interrupt status bit is pending when the controller transitions to D0, an interrupt may be generated. When the controller is put into D3, it is assumed that software has properly shut down the device and disabled the ports. Therefore, there is no need to sustain any values on the port wires. The interface will be treated as if no device is present on the cable, and power will be minimized. When returning from a D3 state, an internal reset will not be performed. 5.17.8.2.4 Non-AHCI Mode PME# Generation When in non-AHCI mode (legacy mode) of operation, the SATA controller does not generate PME#. This includes attach events (since the port must be disabled), or interlock switch events (using the SATAGP pins). 5.17.8.3 SMI Trapping (APM) D31:F2:Offset C0h (see Section 13.1.43) contain control for generating SMI# on accesses to the IDE I/O spaces. These bits map to the legacy ranges (1F0-1F7h, 3F6h, 170-177h, and 376h) and native IDE ranges defined by PCMdBA, PCTLBA, SCMdBA an SCTLBA. If the SATA controller is in legacy mode and is using these addresses, accesses to one of these ranges with the appropriate bit set causes the cycle to not be forwarded to the SATA controller, and for an SMI# to be generated. If an access to the Bus-Master IDE registers occurs while trapping is enabled for the device being accessed, then the register is updated, an SMI# is generated, and the device activity status bits (Section 13.1.44) are updated indicating that a trap occurred. 5.17.9 SATA Device Presence In legacy mode, the SATA controller does not generate interrupts based on Hot-Plug/ unplug events. However, the SATA PHY does know when a device is connected (if not in a partial or slumber state), and it s beneficial to communicate this information to host software as this will greatly reduce boot times and resume times. The flow used to indicate SATA device presence is shown in Figure 5-11. The `PxE' bit refers to PCS.P[3:0]E bits, depending on the port being checked and the `PxP' bits refer to the PCS.P[3:0]P bits, depending on the port being checked. If the PCS/PxP bit is set a device is present, if the bit is cleared a device is not present. If a port is disabled, software can check to see if a new device is connected by periodically re-enabling the port and observing if a device is present, if a device is not present it can disable the port and check again later. If a port remains enabled, software can periodically poll PCS.PxP to see if a new device is connected. Datasheet 191 Functional Description Figure 5-11. Flow for Port Enable / Device Present Bits 5.17.10 SATA LED The SATALED# output is driven whenever the BSY bit is set in any SATA port. The SATALED# is an active-low open-drain output. When SATALED# is low, the LED should be active. When SATALED# is high, the LED should be inactive. 5.17.11 AHCI Operation The PCH provides hardware support for Advanced Host Controller Interface (AHCI), a programming interface for SATA host controllers developed through a joint industry effort. AHCI defines transactions between the SATA controller and software and enables advanced performance and usability with SATA. Platforms supporting AHCI may take advantage of performance features such as no master/slave designation for SATA devices--each device is treated as a master--and hardware assisted native command queuing. AHCI also provides usability enhancements such as Hot-Plug. AHCI requires appropriate software support (such as, an AHCI driver) and for some features, hardware support in the SATA device or additional platform hardware. The PCH supports all of the mandatory features of the Serial ATA Advanced Host Controller Interface Specification, Revision 1.3 and many optional features, such as hardware assisted native command queuing, aggressive power management, LED indicator support, and Hot-Plug through the use of interlock switch support (additional platform hardware and software may be required depending upon the implementation). Note: 192 For reliable device removal notification while in AHCI operation without the use of interlock switches (surprise removal), interface power management should be disabled for the associated port. See Section 7.3.1 of the AHCI Specification for more information. Datasheet Functional Description 5.17.12 SGPIO Signals The SGPIO signals, in accordance to the SFF-8485 specification, support per-port LED signaling. These signals are not related to SATALED#, which allows for simplified indication of SATA command activity. The SGPIO group interfaces with an external controller chip that fetches and serializes the data for driving across the SGPIO bus. The output signals then control the LEDs. This feature is only valid in AHCI/RAID mode. Note: Intel does not validate all possible usage cases of this feature. Customers should validate their specific design implementation on their own platforms. 5.17.12.1 Mechanism The enclosure management for SATA Controller 1 (Device 31: Function 2) involves sending messages that control LEDs in the enclosure. The messages for this function are stored after the normal registers in the AHCI BAR, at Offset 580h bytes for the PCH from the beginning of the AHCI BAR as specified by the EM_LOC global register (Section 13.4.1.6). Software creates messages for transmission in the enclosure management message buffer. The data in the message buffer should not be changed if CTL.TM bit is set by software to transmit an update message. Software should only update the message buffer when CTL.TM bit is cleared by hardware otherwise the message transmitted will be indeterminate. Software then writes a register to cause hardware to transmit the message or take appropriate action based on the message content. The software should only create message types supported by the controller, which is LED messages for the PCH. If the software creates other non LED message types (such as, SAF-TE, SES-2), the SGPIO interface may hang and the result is indeterminate. During reset all SGPIO pins will be in tri-state state. The interface will continue staying in tri-state state after reset until the first transmission occurs, when software programs the message buffer and sets the transmit bit CTL.TM. The SATA host controller will initiate the transmission by driving SCLOCK and at the same time driving the SLOAD to "0 prior to the actual bit stream transmission. The Host will drive SLOAD low for at least 5 SCLOCK then only start the bit stream by driving the SLOAD to high. SLOAD will be driven high for 1 SCLOCK, followed by vendor-specific pattern that is default to "0000" if software is yet to program the value. A total of 18-bit streams from 6 ports (Port0, Port1, Port2, Port3, Port4 and Port5) of 3-bit per port LED message will be transmitted on SDATAOUT0 pin after the SLOAD is driven high for 1 SCLOCK. Only 2 ports (port4, and port 5) of 6-bit total LED message follow by 12 bits of tri-state value will be transmitted out on SDATAOUT1 pin. All the default LED message values will be high prior to software setting them, except the Activity LED message that is configured to be hardware driven that will be generated based on the activity from the respective port. All the LED message values will be driven to `1' for the port that is unimplemented as indicated in the Port Implemented register regardless of the software programmed value through the message buffer. There are 2 different ways of resetting the PCH's SGPIO interface, asynchronous reset and synchronous reset. Asynchronous reset is caused by platform reset to cause the SGPIO interface to be tri-state asynchronously. Synchronous reset is caused by setting the CTL.RESET bit, clearing the GHC.AE bit or HBA reset, where Host Controller will Datasheet 193 Functional Description complete the existing full bit stream transmission then only tri-state all the SGPIO pins. After the reset, both synchronous and asynchronous, the SGPIO pins will stay tristated. Note: The PCH Host Controller does not ensure that it will cause the target SGPIO device or controller to be reset. Software is responsible to keep the PCH SGPIO interface in tristate for 2 second to cause a reset on the target of the SGPIO interface. 5.17.12.2 Message Format Messages shall be constructed with a one DWord header that describes the message to be sent followed by the actual message contents. The first DWord shall be constructed as shown in the following table. Table 5-43. Message Format Bit Description 31:28 Reserved 27:24 Message Type (MTYPE): Specifies the type of the message. The message types are: 0h = LED 1h = SAF-TE 2h = SES-2 3h = SGPIO (register based interface) All other values reserved 23:16 Data Size (DSIZE): Specifies the data size in bytes. If the message (enclosure services command) has a data buffer that is associated with it that is transferred, the size of that data buffer is specified in this field. If there is no separate data buffer, this field shall have a value of `0'. The data directly follows the message in the message buffer. For the PCH, this value should always be `0'. 15:8 Message Size (MSIZE): Specifies the size of the message in bytes. The message size does not include the one DWord header. A value of `0' is invalid. For the PCH, the message size is always 4 bytes. 7:0 Reserved The SAF-TE, SES-2, and SGPIO message formats are defined in the corresponding specifications, respectively. The LED message type is defined in Section 5.17.12.3. It is the responsibility of software to ensure the content of the message format is correct. If the message type is not programmed as 'LED' for this controller, the controller shall not take any action to update its LEDs. For LED message type, the message size always consists of 4 bytes. 5.17.12.3 LED Message Type The LED message type specifies the status of up to three LEDs. Typically, the usage for these LEDs is activity, fault, and locate. Not all implementations necessarily contain all LEDs (for example, some implementations may not have a locate LED). The message identifies the HBA port number and the Port Multiplier port number that the slot status applies to. If a Port Multiplier is not in use with a particular device, the Port Multiplier port number shall be `0'. The format of the LED message type is defined in Table 5-44. The LEDs shall retain their values until there is a following update for that particular slot. 194 Datasheet Functional Description Table 5-44. Multi-activity LED Message Type Byte 3-2 Description Value (VAL): This field describes the state of each LED for a particular location. There are three LEDs that may be supported by the HBA. Each LED has 3 bits of control. LED values are: 000b - LED shall be off 001b - LED shall be solid on as perceived by human eye All other values reserved The LED bit locations are: Bits 2:0 - Activity LED (may be driven by hardware) Bits 5:3 - Vendor Specific LED (such as locate) Bits 8:6 - Vendor Specific LED (such as fault) Bits 15:9 - Reserved Vendor specific message is: Bit 3:0 - Vendor Specific Pattern Bit 15:4 - Reserved Note: 1 0 If Activity LED Hardware Driven (ATTR.ALHD) bit is set, host will output the hardware LED value sampled internally and will ignore software written activity value on bit [2:0]. Since the PCH Enclosure Management does not support port multiplier based LED message, the LED message will be generated independently based on respective port's operation activity. Vendor specific LED values Locate (Bits 5:3) and Fault (Bits 8:6) always are driven by software. Port Multiplier Information: Specifies slot specific information related to Port Multiplier. Bits 3:0 specify the Port Multiplier port number for the slot that requires the status update. If a Port Multiplier is not attached to the device in the affected slot, the Port Multiplier port number shall be '0'. Bits 7:4 are reserved. The PCH does not support LED messages for devices behind a Port MUltiplier. This byte should be 0. HBA Information: Specifies slot specific information related to the HBA. Bits 4:0 - HBA port number for the slot that requires the status update. Bit 5 - If set to '1', value is a vendor specific message that applies to the entire enclosure. If cleared to '0', value applies to the port specified in bits 4:0. Bits 7:6 - Reserved Datasheet 195 Functional Description 5.17.12.4 SGPIO Waveform Figure 5-12. Serial Data transmitted over the SGPIO Interface 196 Datasheet Functional Description 5.17.13 External SATA The PCH supports external SATA. External SATA uses the SATA interface outside of the system box. The usage model for this feature must comply with the Serial ATA II Cables and Connectors Volume 2 Gold specification at www.sata-io.org. Intel validates two configurations: 1. The cable-up solution involves an internal SATA cable that connects to the SATA motherboard connector and spans to a back panel PCI bracket with an eSATA connector. A separate eSATA cable is required to connect an eSATA device. 2. The back-panel solution involves running a trace to the I/O back panel and connecting a device using an external SATA connector on the board. 5.18 High Precision Event Timers (HPET) This function provides a set of timers that can be used by the operating system. The timers are defined such that the operating system may be able to assign specific timers to be used directly by specific applications. Each timer can be configured to cause a separate interrupt. The PCH provides eight timers. The timers are implemented as a single counter, and each timer has its own comparator and value register. The counter increases monotonically. Each individual timer can generate an interrupt when the value in its value register matches the value in the main counter. The registers associated with these timers are mapped to a memory space (much like the I/O APIC). However, it is not implemented as a standard PCI function. The BIOS reports to the operating system the location of the register space. The hardware can support an assignable decode space; however, the BIOS sets this space prior to handing it over to the operating system. It is not expected that the operating system will move the location of these timers once it is set by the BIOS. 5.18.1 Timer Accuracy The timers are accurate over any 1 ms period to within 0.05% of the time specified in the timer resolution fields. Within any 100 microsecond period, the timer reports a time that is up to two ticks too early or too late. Each tick is less than or equal to 100 ns, so this represents an error of less than 0.2%. The timer is monotonic. It does not return the same value on two consecutive reads (unless the counter has rolled over and reached the same value). The main counter is clocked by the 14.31818 MHz clock. The accuracy of the main counter is as accurate as the 14.31818 MHz clock. 5.18.2 Interrupt Mapping Mapping Option #1 (Legacy Replacement Option) In this case, the Legacy Replacement Rout bit (LEG_RT_CNF) is set. This forces the mapping found in Table 5-45. Datasheet 197 Functional Description Table 5-45. Legacy Replacement Routing Timer 8259 Mapping APIC Mapping 0 IRQ0 IRQ2 In this case, the 8254 timer will not cause any interrupts 1 IRQ8 IRQ8 In this case, the RTC will not cause any interrupts. 2 and 3 Per IRQ Routing Field. Per IRQ Routing Field 4, 5, 6, 7 not available not available Note: Comment The Legacy Option does not preclude delivery of IRQ0/IRQ8 using processor interrupts messages. Mapping Option #2 (Standard Option) In this case, the Legacy Replacement Rout bit (LEG_RT_CNF) is 0. Each timer has its own routing control. The interrupts can be routed to various interrupts in the 8259 or I/O APIC. A capabilities field indicates which interrupts are valid options for routing. If a timer is set for edge-triggered mode, the timers should not be shared with any legacy interrupts. For the PCH, the only supported interrupt values are as follows: Timer 0 and 1: IRQ20, 21, 22 and 23 (I/O APIC only). Timer 2: IRQ11 (8259 or I/O APIC) and IRQ20, 21, 22 and 23 (I/O APIC only). Timer 3: IRQ12 (8259 or I/O APIC) and IRQ 20, 21, 22 and 23 (I/O APIC only). Interrupts from Timer 4, 5, 6, 7 can only be delivered using processor message interrupts. Mapping Option #3 (Processor Message Option) In this case, the interrupts are mapped directly to processor messages without going to the 8259 or I/O (x) APIC. To use this mode, the interrupt must be configured to edgetriggered mode. The Tn_PROCMSG_EN_CNF bit must be set to enable this mode. When the interrupt is delivered to the processor, the message is delivered to the address indicated in the Tn_PROCMSG_INT_ADDR field. The data value for the write cycle is specified in the Tn_PROCMSG_INT_VAL field. Notes: 1. The processor message interrupt delivery option has HIGHER priority and is mutually exclusive to the standard interrupt delivery option. Thus, if the Tn_PROCMSG_EN_CNF bit is set, the interrupts will be delivered directly to the processor, rather than using the APIC or 8259. The processor message interrupt delivery can be used even when the legacy mapping is used. 198 Datasheet Functional Description 5.18.3 Periodic versus Non-Periodic Modes Non-Periodic Mode Timer 0 is configurable to 32 (default) or 64-bit mode, whereas Timers 1:7 only support 32-bit mode (See Section 20.1.5). All of the timers support non-periodic mode. Refer to Section 2.3.9.2.1 of the IA-PC HPET Specification for a description of this mode. Periodic Mode Timer 0 is the only timer that supports periodic mode. Refer to Section 2.3.9.2.2 of the IA-PC HPET Specification for a description of this mode. The following usage model is expected: 1. Software clears the ENABLE_CNF bit to prevent any interrupts. 2. Software Clears the main counter by writing a value of 00h to it. 3. Software sets the TIMER0_VAL_SET_CNF bit. 4. Software writes the new value in the TIMER0_COMPARATOR_VAL register. 5. Software sets the ENABLE_CNF bit to enable interrupts. The Timer 0 Comparator Value register cannot be programmed reliably by a single 64-bit write in a 32-bit environment except if only the periodic rate is being changed during run-time. If the actual Timer 0 Comparator Value needs to be reinitialized, then the following software solution will always work regardless of the environment: 1. Set TIMER0_VAL_SET_CNF bit. 2. Set the lower 32 bits of the Timer0 Comparator Value register. 3. Set TIMER0_VAL_SET_CNF bit. 4. Set the upper 32 bits of the Timer0 Comparator Value register. 5.18.4 Enabling the Timers The BIOS or operating system PnP code should route the interrupts. This includes the Legacy Rout bit, Interrupt Rout bit (for each timer), interrupt type (to select the edge or level type for each timer) The Device Driver code should do the following for an available timer: 1. Set the Overall Enable bit (Offset 10h, bit 0). 2. Set the timer type field (selects one-shot or periodic). 3. Set the interrupt enable. 4. Set the comparator value. Datasheet 199 Functional Description 5.18.5 Interrupt Levels Interrupts directed to the internal 8259s are active high. See Section 5.10 for information regarding the polarity programming of the I/O APIC for detecting internal interrupts. If the interrupts are mapped to the 8259 or I/O APIC and set for level-triggered mode, they can be shared with legacy interrupts. They may be shared although it is unlikely for the operating system to attempt to do this. If more than one timer is configured to share the same IRQ (using the TIMERn_INT_ROUT_CNF fields), then the software must configure the timers to leveltriggered mode. Edge-triggered interrupts cannot be shared. 5.18.6 Handling Interrupts If each timer has a unique interrupt and the timer has been configured for edgetriggered mode, then there are no specific steps required. No read is required to process the interrupt. If a timer has been configured to level-triggered mode, then its interrupt must be cleared by the software. This is done by reading the interrupt status register and writing a 1 back to the bit position for the interrupt to be cleared. Independent of the mode, software can read the value in the main counter to see how much time has passed between when the interrupt was generated and when it was first serviced. If Timer 0 is set up to generate a periodic interrupt, the software can check to see how much time remains until the next interrupt by checking the timer value register. 5.18.7 Issues Related to 64-Bit Timers with 32-Bit Processors A 32-bit timer can be read directly using processors that are capable of 32-bit or 64-bit instructions. However, a 32-bit processor may not be able to directly read 64-bit timer. A race condition comes up if a 32-bit processor reads the 64-bit register using two separate 32-bit reads. The danger is that just after reading one half, the other half rolls over and changes the first half. If a 32-bit processor needs to access a 64-bit timer, it must first halt the timer before reading both the upper and lower 32-bits of the timer. If a 32-bit processor does not want to halt the timer, it can use the 64-bit timer as a 32-bit timer by setting the TIMERn_32MODE_CNF bit. This causes the timer to behave as a 32-bit timer. The upper 32-bits are always 0. Alternatively, software may do a multiple read of the counter while it is running. Software can read the high 32 bits, then the low 32 bits, the high 32 bits again. If the high 32 bits have not changed between the two reads, then a rollover has not happened and the low 32 bits are valid. If the high 32 bits have changed between reads, then the multiple reads are repeated until a valid read is performed. Note: 200 On a 64-bit platform, if software attempts a 64-bit read of the 64-bit counter, software must be aware that some platforms may split the 64-bit read into two 32-bit reads. The read maybe inaccurate if the low 32 bits roll over between the high and low reads. Datasheet Functional Description 5.19 USB EHCI Host Controllers (D29:F0 and D26:F0) The PCH contains two Enhanced Host Controller Interface (EHCI) host controllers which support up to fourteen USB 2.0 high-speed root ports. USB 2.0 allows data transfers up to 480 Mb/s. USB 2.0 based Debug Port is also implemented in the PCH. 5.19.1 EHC Initialization The following descriptions step through the expected PCH Enhanced Host Controller (EHC) initialization sequence in chronological order, beginning with a complete power cycle in which the suspend well and core well have been off. 5.19.1.1 BIOS Initialization BIOS performs a number of platform customization steps after the core well has powered up. Contact your Intel Field Representative for additional PCH BIOS information. 5.19.1.2 Driver Initialization See Chapter 4 of the Enhanced Host Controller Interface Specification for Universal Serial Bus, Revision 1.0. 5.19.1.3 EHC Resets In addition to the standard PCH hardware resets, portions of the EHC are reset by the HCRESET bit and the transition from the D3HOT device power management state to the D0 state. The effects of each of these resets are shown in the following table. Table 5-46. EHC Resets Reset Does Reset Does Not Reset Comments HCRESET bit set. Memory space registers except Structural Parameters (which is written by BIOS). Configuration registers. The HCRESET must only affect registers that the EHCI driver controls. PCI Configuration space and BIOSprogrammed parameters cannot be reset. Software writes the Device Power State from D3HOT (11b) to D0 (00b). Core well registers (except BIOSprogrammed registers). Suspend well registers; BIOSprogrammed core well registers. The D3-to-D0 transition must not cause wake information (suspend well) to be lost. It also must not clear BIOSprogrammed registers because BIOS may not be invoked following the D3to-D0 transition. If the detailed register descriptions give exceptions to these rules, those exceptions override these rules. This summary is provided to help explain the reasons for the reset policies. 5.19.2 Data Structures in Main Memory See Section 3 and Appendix B of the Enhanced Host Controller Interface Specification for Universal Serial Bus, Revision 1.0 for details. Datasheet 201 Functional Description 5.19.3 USB 2.0 Enhanced Host Controller DMA The PCH USB 2.0 EHC implements three sources of USB packets. They are, in order of priority on USB during each microframe: 1. The USB 2.0 Debug Port, 2. The Periodic DMA engine, and 3. The Asynchronous DMA engine. The PCH always performs any currently-pending debug port transaction at the beginning of a microframe, followed by any pending periodic traffic for the current microframe. If there is time left in the microframe, then the EHC performs any pending asynchronous traffic until the end of the microframe (EOF1). The debug port traffic is only presented on Port 1 and Port 9, while the other ports are idle during this time. 5.19.4 Data Encoding and Bit Stuffing See Chapter 8 of the Universal Serial Bus Specification, Revision 2.0. 5.19.5 Packet Formats See Chapter 8 of the Universal Serial Bus Specification, Revision 2.0. The PCH EHCI allows entrance to USB test modes, as defined in the USB 2.0 specification, including Test J, Test Packet, and so on. However, the PCH Test Packet test mode interpacket gap timing may not meet the USB 2.0 specification. 5.19.6 USB 2.0 Interrupts and Error Conditions Section 4 of the Enhanced Host Controller Interface Specification for Universal Serial Bus, Revision 1.0 goes into detail on the EHC interrupts and the error conditions that cause them. All error conditions that the EHC detects can be reported through the EHCI Interrupt status bits. Only PCH-specific interrupt and error-reporting behavior is documented in this section. The EHCI Interrupts section must be read first, followed by this section of the datasheet to fully comprehend the EHC interrupt and error-reporting functionality. * Based on the EHC Buffer sizes and buffer management policies, the Data Buffer Error can never occur on the PCH. * Master Abort and Target Abort responses from hub interface on EHC-initiated read packets will be treated as Fatal Host Errors. The EHC halts when these conditions are encountered. * The PCH may assert the interrupts which are based on the interrupt threshold as soon as the status for the last complete transaction in the interrupt interval has been posted in the internal write buffers. The requirement in the Enhanced Host Controller Interface Specification for Universal Serial Bus, Revision 1.0 (that the status is written to memory) is met internally, even though the write may not be seen on DMI before the interrupt is asserted. * Since the PCH supports the 1024-element Frame List size, the Frame List Rollover interrupt occurs every 1024 milliseconds. * The PCH delivers interrupts using PIRQH#. * The PCH does not modify the CERR count on an Interrupt IN when the "Do Complete-Split" execution criteria are not met. 202 Datasheet Functional Description * For complete-split transactions in the Periodic list, the "Missed Microframe" bit does not get set on a control-structure-fetch that fails the late-start test. If subsequent accesses to that control structure do not fail the late-start test, then the "Missed Microframe" bit will get set and written back. 5.19.6.1 Aborts on USB 2.0-Initiated Memory Reads If a read initiated by the EHC is aborted, the EHC treats it as a fatal host error. The following actions are taken when this occurs: * The Host System Error status bit is set. * The DMA engines are halted after completing up to one more transaction on the USB interface. * If enabled (by the Host System Error Enable), then an interrupt is generated. * If the status is Master Abort, then the Received Master Abort bit in configuration space is set. * If the status is Target Abort, then the Received Target Abort bit in configuration space is set. * If enabled (by the SERR Enable bit in the function's configuration space), then the Signaled System Error bit in configuration bit is set. 5.19.7 USB 2.0 Power Management 5.19.7.1 Pause Feature This feature allows platforms to dynamically enter low-power states during brief periods when the system is idle (that is, between keystrokes). This is useful for enabling power management features in the PCH. The policies for entering these states typically are based on the recent history of system bus activity to incrementally enter deeper power management states. Normally, when the EHC is enabled, it regularly accesses main memory while traversing the DMA schedules looking for work to do; this activity is viewed by the power management software as a non-idle system, thus preventing the power managed states to be entered. Suspending all of the enabled ports can prevent the memory accesses from occurring, but there is an inherent latency overhead with entering and exiting the suspended state on the USB ports that makes this unacceptable for the purpose of dynamic power management. As a result, the EHCI software drivers are allowed to pause the EHC DMA engines when it knows that the traffic patterns of the attached devices can afford the delay. The pause only prevents the EHC from generating memory accesses; the SOF packets continue to be generated on the USB ports (unlike the suspended state). 5.19.7.2 Suspend Feature The Enhanced Host Controller Interface (EHCI) For Universal Serial Bus Specification, Section 4.3 describes the details of Port Suspend and Resume. 5.19.7.3 ACPI Device States The USB 2.0 function only supports the D0 and D3 PCI Power Management states. Notes regarding the PCH implementation of the Device States: 1. The EHC hardware does not inherently consume any more power when it is in the D0 state than it does in the D3 state. However, software is required to suspend or disable all ports prior to entering the D3 state such that the maximum power consumption is reduced. Datasheet 203 Functional Description 2. In the D0 state, all implemented EHC features are enabled. 3. In the D3 state, accesses to the EHC memory-mapped I/O range will master abort. Since the Debug Port uses the same memory range, the Debug Port is only operational when the EHC is in the D0 state. 4. In the D3 state, the EHC interrupt must never assert for any reason. The internal PME# signal is used to signal wake events, and so on. 5. When the Device Power State field is written to D0 from D3, an internal reset is generated. See Section 5.19.1.3, "EHC Resets" for general rules on the effects of this reset. 6. Attempts to write any other value into the Device Power State field other than 00b (D0 state) and 11b (D3 state) will complete normally without changing the current value in this field. 5.19.7.4 ACPI System States The EHC behavior as it relates to other power management states in the system is summarized in the following list: * The System is always in the S0 state when the EHC is in the D0 state. However, when the EHC is in the D3 state, the system may be in any power management state (including S0). * When in D0, the Pause feature (See Section 5.19.7.1) enables dynamic processor low-power states to be entered. * The PLL in the EHC is disabled when entering the S3/S4/S5 states (core power turns off). * All core well logic is reset in the S3/S4/S5 states. 5.19.8 USB 2.0 Legacy Keyboard Operation The PCH must support the possibility of a keyboard downstream from either a fullspeed/low-speed or a high-speed port. The description of the legacy keyboard support is unchanged from USB 1.1. The EHC provides the basic ability to generate SMIs on an interrupt event, along with more sophisticated control of the generation of SMIs. 5.19.9 USB 2.0 Based Debug Port The PCH supports the elimination of the legacy COM ports by providing the ability for debugger software to interact with devices on a USB 2.0 port. High-level restrictions and features are: * Operational before USB 2.0 drivers are loaded. * Functions even when the port is disabled. * Allows normal system USB 2.0 traffic in a system that may only have one USB port. * Debug Port device (DPD) must be high-speed capable and connect directly to Port 1 and Port 9 on PCH-based systems (such as, the DPD cannot be connected to Port 1/Port 9 through a hub. When a DPD is detected the PCH EHCI will bypass the integrated Rate Matching Hub and connect directly to the port and the DPD.). * Debug Port FIFO always makes forward progress (a bad status on USB is simply presented back to software). * The Debug Port FIFO is only given one USB access per microframe. 204 Datasheet Functional Description The Debug port facilitates operating system and device driver debug. It allows the software to communicate with an external console using a USB 2.0 connection. Because the interface to this link does not go through the normal USB 2.0 stack, it allows communication with the external console during cases where the operating system is not loaded, the USB 2.0 software is broken, or where the USB 2.0 software is being debugged. Specific features of this implementation of a debug port are: * Only works with an external USB 2.0 debug device (console) * Implemented for a specific port on the host controller * Operational anytime the port is not suspended AND the host controller is in D0 power state. * Capability is interrupted when port is driving USB RESET 5.19.9.1 Theory of Operation There are two operational modes for the USB debug port: 1. Mode 1 is when the USB port is in a disabled state from the viewpoint of a standard host controller driver. In Mode 1, the Debug Port controller is required to generate a "keepalive" packets less than 2 ms apart to keep the attached debug device from suspending. The keepalive packet should be a standalone 32-bit SYNC field. 2. Mode 2 is when the host controller is running (that is, host controller's Run/Stop# bit is 1). In Mode 2, the normal transmission of SOF packets will keep the debug device from suspending. Behavioral Rules 1. In both modes 1 and 2, the Debug Port controller must check for software requested debug transactions at least every 125 microseconds. 2. If the debug port is enabled by the debug driver, and the standard host controller driver resets the USB port, USB debug transactions are held off for the duration of the reset and until after the first SOF is sent. 3. If the standard host controller driver suspends the USB port, then USB debug transactions are held off for the duration of the suspend/resume sequence and until after the first SOF is sent. 4. The ENABLED_CNT bit in the debug register space is independent of the similar port control bit in the associated Port Status and Control register. Table 5-47 shows the debug port behavior related to the state of bits in the debug registers as well as bits in the associated Port Status and Control register. Table 5-47. Debug Port Behavior (Sheet 1 of 2) OWNER_CNT ENABLED_CT Port Enable Run / Stop Suspend 0 X X X X Debug port is not being used. Normal operation. 1 0 X X X Debug port is not being used. Normal operation. 1 1 0 0 X Debug port in Mode 1. SYNC keepalives sent plus debug traffic 1 1 0 1 X Debug port in Mode 2. SOF (and only SOF) is sent as keepalive. Debug traffic is also sent. No other normal traffic is sent out this port, because the port is not enabled. 1 1 1 0 0 Invalid. Host controller driver should never put controller into this state (enabled, not running and not suspended). Datasheet Debug Port Behavior 205 Functional Description Table 5-47. Debug Port Behavior (Sheet 2 of 2) OWNER_CNT ENABLED_CT Port Enable Run / Stop Suspend 1 1 1 0 1 Port is suspended. No debug traffic sent. 1 1 1 1 0 Debug port in Mode 2. Debug traffic is interspersed with normal traffic. 1 1 1 1 1 Port is suspended. No debug traffic sent. 5.19.9.1.1 Debug Port Behavior OUT Transactions An Out transaction sends data to the debug device. It can occur only when the following are true: * The debug port is enabled * The debug software sets the GO_CNT bit * The WRITE_READ#_CNT bit is set The sequence of the transaction is: 1. Software sets the appropriate values in the following bits: -- USB_ADDRESS_CNF -- USB_ENDPOINT_CNF -- DATA_BUFFER[63:0] -- TOKEN_PID_CNT[7:0] -- SEND_PID_CNT[15:8] -- DATA_LEN_CNT -- WRITE_READ#_CNT: (note: this will always be 1 for OUT transactions) -- GO_CNT: (note: this will always be 1 to initiate the transaction) 2. The debug port controller sends a token packet consisting of: -- SYNC -- TOKEN_PID_CNT field -- USB_ADDRESS_CNT field -- USB_ENDPOINT_CNT field -- 5-bit CRC field 3. After sending the token packet, the debug port controller sends a data packet consisting of: -- SYNC -- SEND_PID_CNT field -- The number of data bytes indicated in DATA_LEN_CNT from the DATA_BUFFER -- 16-bit CRC Note: 206 A DATA_LEN_CNT value of 0 is valid in which case no data bytes would be included in the packet. Datasheet Functional Description 4. After sending the data packet, the controller waits for a handshake response from the debug device. -- If a handshake is received, the debug port controller: a. Places the received PID in the RECEIVED_PID_STS field b. Resets the ERROR_GOOD#_STS bit c. Sets the DONE_STS bit -- If no handshake PID is received, the debug port controller: a. Sets the EXCEPTION_STS field to 001b b. Sets the ERROR_GOOD#_STS bit c. Sets the DONE_STS bit 5.19.9.1.2 IN Transactions An IN transaction receives data from the debug device. It can occur only when the following are true: * The debug port is enabled * The debug software sets the GO_CNT bit * The WRITE_READ#_CNT bit is reset The sequence of the transaction is: 1. Software sets the appropriate values in the following bits: -- USB_ADDRESS_CNF -- USB_ENDPOINT_CNF -- TOKEN_PID_CNT[7:0] -- DATA_LEN_CNT -- WRITE_READ#_CNT: (note: this will always be 0 for IN transactions) -- GO_CNT: (note: this will always be 1 to initiate the transaction) 2. The debug port controller sends a token packet consisting of: -- SYNC -- TOKEN_PID_CNT field -- USB_ADDRESS_CNT field -- USB_ENDPOINT_CNT field -- 5-bit CRC field. 3. After sending the token packet, the debug port controller waits for a response from the debug device. If a response is received: -- The received PID is placed into the RECEIVED_PID_STS field -- Any subsequent bytes are placed into the DATA_BUFFER -- The DATA_LEN_CNT field is updated to show the number of bytes that were received after the PID. 4. If a valid packet was received from the device that was one byte in length (indicating it was a handshake packet), then the debug port controller: -- Resets the ERROR_GOOD#_STS bit -- Sets the DONE_STS bit Datasheet 207 Functional Description 5. If a valid packet was received from the device that was more than one byte in length (indicating it was a data packet), then the debug port controller: -- Transmits an ACK handshake packet -- Resets the ERROR_GOOD#_STS bit -- Sets the DONE_STS bit 6. If no valid packet is received, then the debug port controller: -- Sets the EXCEPTION_STS field to 001b -- Sets the ERROR_GOOD#_STS bit -- Sets the DONE_STS bit. 5.19.9.1.3 Debug Software Enabling the Debug Port There are two mutually exclusive conditions that debug software must address as part of its startup processing: * The EHCI has been initialized by system software * The EHCI has not been initialized by system software Debug software can determine the current `initialized' state of the EHCI by examining the Configure Flag in the EHCI USB 2.0 Command Register. If this flag is set, then system software has initialized the EHCI. Otherwise, the EHCI should not be considered initialized. Debug software will initialize the debug port registers depending on the state of the EHCI. However, before this can be accomplished, debug software must determine which root USB port is designated as the debug port. Determining the Debug Port Debug software can easily determine which USB root port has been designated as the debug port by examining bits 20:23 of the EHCI Host Controller Structural Parameters register. This 4-bit field represents the numeric value assigned to the debug port (that is, 0001=port 1). Debug Software Startup with Non-Initialized EHCI Debug software can attempt to use the debug port if after setting the OWNER_CNT bit, the Current Connect Status bit in the appropriate (See Determining the Debug Port Presence) PORTSC register is set. If the Current Connect Status bit is not set, then debug software may choose to terminate or it may choose to wait until a device is connected. If a device is connected to the port, then debug software must reset/enable the port. Debug software does this by setting and then clearing the Port Reset bit the PORTSC register. To ensure a successful reset, debug software should wait at least 50 ms before clearing the Port Reset bit. Due to possible delays, this bit may not change to 0 immediately; reset is complete when this bit reads as 0. Software must not continue until this bit reads 0. If a high-speed device is attached, the EHCI will automatically set the Port Enabled/ Disabled bit in the PORTSC register and the debug software can proceed. Debug software should set the ENABLED_CNT bit in the Debug Port Control/Status register, and then reset (clear) the Port Enabled/Disabled bit in the PORTSC register (so that the system host controller driver does not see an enabled port when it is first loaded). 208 Datasheet Functional Description Debug Software Startup with Initialized EHCI Debug software can attempt to use the debug port if the Current Connect Status bit in the appropriate (See Determining the Debug Port) PORTSC register is set. If the Current Connect Status bit is not set, then debug software may choose to terminate or it may choose to wait until a device is connected. If a device is connected, then debug software must set the OWNER_CNT bit and then the ENABLED_CNT bit in the Debug Port Control/Status register. Determining Debug Peripheral Presence After enabling the debug port functionality, debug software can determine if a debug peripheral is attached by attempting to send data to the debug peripheral. If all attempts result in an error (Exception bits in the Debug Port Control/Status register indicates a Transaction Error), then the attached device is not a debug peripheral. If the debug port peripheral is not present, then debug software may choose to terminate or it may choose to wait until a debug peripheral is connected. 5.19.10 EHCI Caching EHCI Caching is a power management feature in the USB (EHCI) host controllers which enables the controller to execute the schedules entirely in cache and eliminates the need for the DMA engine to access memory when the schedule is idle. EHCI caching allows the processor to maintain longer C-state residency times and provides substantial system power savings. 5.19.11 Intel(R) USB Prefetch Based Pause The Intel USB Prefetch Based Pause is a power management feature in USB (EHCI) host controllers to ensure maximum C3/C4 processor power state time with C2 popup. This feature applies to the period schedule, and works by allowing the DMA engine to identify periods of idleness and preventing the DMA engine from accessing memory when the periodic schedule is idle. Typically in the presence of periodic devices with multiple millisecond poll periods, the periodic schedule will be idle for several frames between polls. The Intel USB Prefetch Based Pause feature is disabled by setting bit 4 of EHCI Configuration Register Section 15.2.1. 5.19.12 Function Level Reset Support (FLR) The USB EHCI Controllers support the Function Level Reset (FLR) capability. The FLR capability can be used in conjunction with Intel Virtualization Technology. FLR allows an Operating System in a Virtual Machine to have complete control over a device, including its initialization, without interfering with the rest of the platform. The device provides a software interface that enables the Operating System to reset the whole device as if a platform reset was asserted. Datasheet 209 Functional Description 5.19.12.1 FLR Steps 5.19.12.1.1 FLR Initialization 1. A FLR is initiated by software writing a `1' to the Initiate FLR bit. 2. All subsequent requests targeting the Function will not be claimed and will be Master Abort Immediate on the bus. This includes any configuration, I/O or Memory cycles, however, the Function shall continue to accept completions targeting the Function. 5.19.12.1.2 FLR Operation The Function will Reset all configuration, I/O and memory registers of the Function except those indicated otherwise and reset all internal states of the Function to the default or initial condition. 5.19.12.1.3 FLR Completion The Initiate FLR bit is reset (cleared) when the FLR reset is completed. This bit can be used to indicate to the software that the FLR reset is completed. Note: From the time Initiate FLR bit is written to 1, software must wait at least 100 ms before accessing the function. 5.19.13 USB Overcurrent Protection The PCH has implemented programmable USB Overcurrent signals. The PCH provides a total of 8 overcurrent pins to be shared across the 14 USB 2.0 and 6 USB 3.0 ports. Each pin is mapped to one or more ports by setting bits in the Over-Current Map registers, depending on whether the port is mapped to EHCI or XHCI. Refer to the following sections for more details: 1. EHCI (USB 2.0 Ports): Section 5.19.13, "USB Overcurrent Protection". 2. XHCI (USB 2.0 Ports): Section 16.1.32, "U2OCM1 - XHCI USB2 Overcurrent Mapping Register1 (USB xHCI--D20:F0)". 3. XHCI (USB 2.0 Ports): Section 16.1.33, "U2OCM2 - XHCI USB2 Overcurrent Mapping Register 2 (USB xHCI--D20:F0)". 4. XHCI (USB 3.0 Ports): Section 16.1.34, "U3OCM1 - XHCI USB3 Overcurrent Pin Mapping 1 (USB xHCI--D20:F0)". 5. XHCI (USB 3.0 Ports): Section 16.1.35, "U3OCM2 - XHCI USB3 Overcurrent Pin Mapping 2 (USB xHCI--D20:F0)". It is system BIOS' responsibility to ensure that each port is mapped to only one over current pin. Operation with more than one overcurrent pin mapped to a port is undefined. It is expected that multiple ports are mapped to a single overcurrent pin, however they should be connected at the port and not at the PCH pin. Shorting these pins together may lead to reduced test capabilities. By default, two ports are routed to each of the OC[6:0]# pins. OC7# is not used by default. NOTES: 1. All USB ports routed out of the package must have Overcurrent protection. It is system BIOS responsibility to ensure all used ports have OC protection. 2. USB Ports that are either unused or only routed within the system (such as, that do not connect to a walk-up port) should not have OC pins assigned to them. 210 Datasheet Functional Description 5.20 Integrated USB 2.0 Rate Matching Hub 5.20.1 Overview The PCH has integrated two USB 2.0 Rate Matching Hubs (RMH). One hub is connected to each of the EHCI controllers as shown in Figure 5-13. The Hubs convert low and fullspeed traffic into high-speed traffic. When the RMHs are enabled, they will appear to software like an external hub is connected to Port 0 of each EHCI controller. In addition, port 1 of each of the RMHs is multiplexed with Port 1 of the EHCI controllers and is able to bypass the RMH for use as the Debug Port. The hub operates like any USB 2.0 Discrete Hub and will consume one tier of hubs allowed by the USB 2.0 Specification, Section 4.1.1. A maximum of four additional nonroot hubs can be supported on any of the PCH USB Ports. The RMH1 will report Vendor ID = 8087h and Product ID = 8000h. RMH2 will report Vendor ID = 8087h and Product ID = 8008h. Figure 5-13. EHCI with USB 2.0 with Rate Matching Hub 5.20.2 Architecture A hub consists of three components: the Hub Repeater, the Hub Controller, and the Transaction Translator. 1. The Hub Repeater is responsible for connectivity setup and tear-down. It also supports exception handling, such as bus fault detection and recovery and connect/ disconnect detect. 2. The Hub Controller provides the mechanism for host-to-hub communication. Hubspecific status and control commands permit the host to configure a hub and to monitor and control its individual downstream facing ports. 3. The Transaction Translator (TT) responds to high-speed split transactions and translates them to full-/low-speed transactions with full-/low-speed devices attached on downstream facing ports. There is 1 TT per RMH in the PCH. See chapter 11 of the USB 2.0 Specification for more details on the architecture of the hubs. Datasheet 211 Functional Description 5.21 xHCI Controller (D20:F0) The PCH contains an eXtensible Host Controller Interface (xHCI) host controller which supports up to 14 USB 2.0 ports of which up to 6 can be used as USB 3.0 ports with board routing, ACPI table and BIOS considerations. This controller allows data transfers of up to 5 Gb/s. The controller supports SuperSpeed (SS), high-speed (HS), full-speed (FS) and low speed (LS) traffic on the bus. The xHCI controller does not have a USB Debug port. If USB debug port functionality is desired then the system SW must use the EHCI-based debug port discussed in Section 5.19.9. Note: Some USB 3.0 motherboard down devices do not require support for USB 2.0 speed and it is possible to route only the SuperSpeed signals, as allowed by the USB 3.0 specification. In this special case, USB 2.0 and USB 3.0 signals will not need to be paired together, thereby allowing support for more than 14 USB connections. 5.22 SMBus Controller (D31:F3) The PCH provides an System Management Bus (SMBus) 2.0 host controller as well as an SMBus Slave Interface. The host controller provides a mechanism for the processor to initiate communications with SMBus peripherals (slaves). The PCH is also capable of operating in a mode in which it can communicate with I2C compatible devices. The host SMBus controller supports up to 100 KHz clock speed. The PCH can perform SMBus messages with either packet error checking (PEC) enabled or disabled. The actual PEC calculation and checking is performed in hardware by the PCH. The Slave Interface allows an external master to read from or write to the PCH. Write cycles can be used to cause certain events or pass messages, and the read cycles can be used to determine the state of various status bits. The PCH's internal host controller cannot access the PCH's internal Slave Interface. The PCH SMBus logic exists in D31:F3 configuration space, and consists of a transmit data path, and host controller. The transmit data path provides the data flow logic needed to implement the seven different SMBus command protocols and is controlled by the host controller. The PCH's SMBus controller logic is clocked by RTC clock. The SMBus Address Resolution Protocol (ARP) is supported by using the existing host controller commands through software, except for the Host Notify command (which is actually a received message). The programming model of the host controller is combined into two portions: a PCI configuration portion, and a system I/O mapped portion. All static configuration, such as the I/O base address, is done using the PCI configuration space. Real-time programming of the Host interface is done in system I/O space. The PCH SMBus host controller checks for parity errors as a target. If an error is detected, the detected parity error bit in the PCI Status Register (D31:F3:Offset 06h:Bit 15) is set. If Bit 6 and Bit 8 of the PCI Command Register (D31:F3:Offset 04h) are set, an SERR# is generated and the signaled SERR# bit in the PCI Status Register (bit 14) is set. 212 Datasheet Functional Description 5.22.1 Host Controller The SMBus host controller is used to send commands to other SMBus slave devices. Software sets up the host controller with an address, command, and, for writes, data and optional PEC; and then tells the controller to start. When the controller has finished transmitting data on writes, or receiving data on reads, it generates an SMI# or interrupt, if enabled. The host controller supports 8 command protocols of the SMBus interface (see System Management Bus (SMBus) Specification, Version 2.0): Quick Command, Send Byte, Receive Byte, Write Byte/Word, Read Byte/Word, Process Call, Block Read/Write, Block Write-Block Read Process Call, and Host Notify. The SMBus host controller requires that the various data and command fields be setup for the type of command to be sent. When software sets the START bit, the SMBus Host controller performs the requested transaction, and interrupts the processor (or generates an SMI#) when the transaction is completed. Once a START command has been issued, the values of the "active registers" (Host Control, Host Command, Transmit Slave Address, Data 0, Data 1) should not be changed or read until the interrupt status message (INTR) has been set (indicating the completion of the command). Any register values needed for computation purposes should be saved prior to issuing of a new command, as the SMBus host controller updates all registers while completing the new command. The PCH supports the System Management Bus (SMBus) Specification, Version 2.0. Slave functionality, including the Host Notify protocol, is available on the SMBus pins. The SMLink and SMBus signals can be tied together externally depending on TCO mode used. Refer to Section 5.15.2 for more details. Using the SMB host controller to send commands to the PCH SMB slave port is not supported. 5.22.1.1 Command Protocols In all of the following commands, the Host Status Register (offset 00h) is used to determine the progress of the command. While the command is in operation, the HOST_BUSY bit is set. If the command completes successfully, the INTR bit will be set in the Host Status Register. If the device does not respond with an acknowledge, and the transaction times out, the DEV_ERR bit is set. If software sets the KILL bit in the Host Control Register while the command is running, the transaction will stop and the FAILED bit will be set. Quick Command When programmed for a Quick Command, the Transmit Slave Address Register is sent. The PEC byte is never appended to the Quick Protocol. Software should force the PEC_EN bit to 0 when performing the Quick Command. Software must force the I2C_EN bit to 0 when running this command. See Section 5.5.1 of the System Management Bus (SMBus) Specification, Version 2.0 for the format of the protocol. Send Byte / Receive Byte For the Send Byte command, the Transmit Slave Address and Device Command Registers are sent. For the Receive Byte command, the Transmit Slave Address Register is sent. The data received is stored in the DATA0 register. Software must force the I2C_EN bit to 0 when running this command. Datasheet 213 Functional Description The Receive Byte is similar to a Send Byte, the only difference is the direction of data transfer. See Sections 5.5.2 and 5.5.3 of the System Management Bus (SMBus) Specification, Version 2.0 for the format of the protocol. Write Byte/Word The first byte of a Write Byte/Word access is the command code. The next 1 or 2 bytes are the data to be written. When programmed for a Write Byte/Word command, the Transmit Slave Address, Device Command, and Data0 Registers are sent. In addition, the Data1 Register is sent on a Write Word command. Software must force the I2C_EN bit to 0 when running this command. See Section 5.5.4 of the System Management Bus (SMBus) Specification, Version 2.0 for the format of the protocol. Read Byte/Word Reading data is slightly more complicated than writing data. First the PCH must write a command to the slave device. Then it must follow that command with a repeated start condition to denote a read from that device's address. The slave then returns 1 or 2 bytes of data. Software must force the I2C_EN bit to 0 when running this command. When programmed for the read byte/word command, the Transmit Slave Address and Device Command Registers are sent. Data is received into the DATA0 on the read byte, and the DAT0 and DATA1 registers on the read word. See Section 5.5.5 of the System Management Bus (SMBus) Specification, Version 2.0 for the format of the protocol. Process Call The process call is so named because a command sends data and waits for the slave to return a value dependent on that data. The protocol is simply a Write Word followed by a Read Word, but without a second command or stop condition. When programmed for the Process Call command, the PCH transmits the Transmit Slave Address, Host Command, DATA0 and DATA1 registers. Data received from the device is stored in the DATA0 and DATA1 registers. The Process Call command with I2C_EN set and the PEC_EN bit set produces undefined results. Software must force either I2C_EN or PEC_EN to 0 when running this command. See Section 5.5.6 of the System Management Bus (SMBus) Specification, Version 2.0 for the format of the protocol. Note: For process call command, the value written into bit 0 of the Transmit Slave Address Register (SMB I/O register, Offset 04h) needs to be 0. Note: If the I2C_EN bit is set, the protocol sequence changes slightly: the Command Code (Bits 18:11 in the bit sequence) are not sent - as a result, the slave will not acknowledge (Bit 19 in the sequence). Block Read/Write The PCH contains a 32-byte buffer for read and write data which can be enabled by setting bit 1 of the Auxiliary Control register at offset 0Dh in I/O space, as opposed to a single byte of buffering. This 32-byte buffer is filled with write data before transmission, and filled with read data on reception. In the PCH, the interrupt is generated only after a transmission or reception of 32 bytes, or when the entire byte count has been transmitted/received. Note: 214 When operating in I2C* mode (I2C_EN bit is set), the PCH will never use the 32-byte buffer for any block commands. Datasheet Functional Description The byte count field is transmitted but ignored by the PCH as software will end the transfer after all bytes it cares about have been sent or received. For a Block Write, software must either force the I2C_EN bit or both the PEC_EN and AAC bits to 0 when running this command. The block write begins with a slave address and a write condition. After the command code the PCH issues a byte count describing how many more bytes will follow in the message. If a slave had 20 bytes to send, the first byte would be the number 20 (14h), followed by 20 bytes of data. The byte count may not be 0. A Block Read or Write is allowed to transfer a maximum of 32 data bytes. When programmed for a block write command, the Transmit Slave Address, Device Command, and Data0 (count) registers are sent. Data is then sent from the Block Data Byte register; the total data sent being the value stored in the Data0 Register. On block read commands, the first byte received is stored in the Data0 register, and the remaining bytes are stored in the Block Data Byte register. See Section 5.5.7 of the System Management Bus (SMBus) Specification, Version 2.0 for the format of the protocol. Note: For Block Write, if the I2C_EN bit is set, the format of the command changes slightly. The PCH will still send the number of bytes (on writes) or receive the number of bytes (on reads) indicated in the DATA0 register. However, it will not send the contents of the DATA0 register as part of the message. Also, the Block Write protocol sequence changes slightly: the Byte Count (bits 27:20 in the bit sequence) are not sent - as a result, the slave will not acknowledge (bit 28 in the sequence). I2C Read This command allows the PCH to perform block reads to certain I2C* devices, such as serial E2PROMs. The SMBus Block Read supports the 7-bit addressing mode only. However, this does not allow access to devices using the I2C "Combined Format" that has data bytes after the address. Typically these data bytes correspond to an offset (address) within the serial memory chips. Note: This command is supported independent of the setting of the I2C_EN bit. The I2C Read command with the PEC_EN bit set produces undefined results. Software must force both the PEC_EN and AAC bit to 0 when running this command. For I2C Read command, the value written into bit 0 of the Transmit Slave Address Register (SMB I/O register, offset 04h) needs to be 0. The format that is used for the command is shown in Table 5-48. Table 5-48. I2C* Block Read (Sheet 1 of 2) Bit 1 8:2 9 10 18:11 Slave Address - 7 bits Write Acknowledge from slave Send DATA1 register 19 Acknowledge from slave 20 Repeated Start 27:21 Datasheet Description Start Slave Address - 7 bits 215 Functional Description Table 5-48. I2C* Block Read (Sheet 2 of 2) Bit 28 29 37:30 38 46:39 47 - Description Read Acknowledge from slave Data byte 1 from slave - 8 bits Acknowledge Data byte 2 from slave - 8 bits Acknowledge Data bytes from slave / Acknowledge - Data byte N from slave - 8 bits - NOT Acknowledge - Stop The PCH will continue reading data from the peripheral until the NAK is received. Block Write-Block Read Process Call The block write-block read process call is a two-part message. The call begins with a slave address and a write condition. After the command code the host issues a write byte count (M) that describes how many more bytes will be written in the first part of the message. If a master has 6 bytes to send, the byte count field will have the value 6 (0000 0110b), followed by the 6 bytes of data. The write byte count (M) cannot be 0. The second part of the message is a block of read data beginning with a repeated start condition followed by the slave address and a Read bit. The next byte is the read byte count (N), which may differ from the write byte count (M). The read byte count (N) cannot be 0. The combined data payload must not exceed 32 bytes. The byte length restrictions of this process call are summarized as follows: * M 1 byte * N 1 byte * M + N 32 bytes The read byte count does not include the PEC byte. The PEC is computed on the total message beginning with the first slave address and using the normal PEC computational rules. It is highly recommended that a PEC byte be used with the Block Write-Block Read Process Call. Software must do a read to the command register (offset 2h) to reset the 32 byte buffer pointer prior to reading the block data register. There is no STOP condition before the repeated START condition, and that a NACK signifies the end of the read transfer. Note: E32B bit in the Auxiliary Control register must be set when using this protocol. See Section 5.5.8 of the System Management Bus (SMBus) Specification, Version 2.0 for the format of the protocol. 216 Datasheet Functional Description 5.22.2 Bus Arbitration Several masters may attempt to get on the bus at the same time by driving the SMBDATA line low to signal a start condition. The PCH continuously monitors the SMBDATA line. When the PCH is attempting to drive the bus to a 1 by letting go of the SMBDATA line, and it samples SMBDATA low, then some other master is driving the bus and the PCH will stop transferring data. If the PCH sees that it has lost arbitration, the condition is called a collision. The PCH will set the BUS_ERR bit in the Host Status Register, and if enabled, generate an interrupt or SMI#. The processor is responsible for restarting the transaction. When the PCH is a SMBus master, it drives the clock. When the PCH is sending address or command as an SMBus master, or data bytes as a master on writes, it drives data relative to the clock it is also driving. It will not start toggling the clock until the start or stop condition meets proper setup and hold time. The PCH will also ensure minimum time between SMBus transactions as a master. Note: The PCH supports the same arbitration protocol for both the SMBus and the System Management (SMLink) interfaces. 5.22.3 Bus Timing 5.22.3.1 Clock Stretching Some devices may not be able to handle their clock toggling at the rate that the PCH as an SMBus master would like. They have the capability of stretching the low time of the clock. When the PCH attempts to release the clock (allowing the clock to go high), the clock will remain low for an extended period of time. The PCH monitors the SMBus clock line after it releases the bus to determine whether to enable the counter for the high time of the clock. While the bus is still low, the high time counter must not be enabled. Similarly, the low period of the clock can be stretched by an SMBus master if it is not ready to send or receive data. 5.22.3.2 Bus Time Out (The PCH as SMBus Master) If there is an error in the transaction, such that an SMBus device does not signal an acknowledge, or holds the clock lower than the allowed time-out time, the transaction will time out. The PCH will discard the cycle and set the DEV_ERR bit. The time out minimum is 25 ms (800 RTC clocks). The time-out counter inside the PCH will start after the last bit of data is transferred by the PCH and it is waiting for a response. The 25-ms time-out counter will not count under the following conditions: 1. BYTE_DONE_STATUS bit (SMBus I/O Offset 00h, Bit 7) is set 2. The SECOND_TO_STS bit (TCO I/O Offset 06h, Bit 1) is not set (this indicates that the system has not locked up). 5.22.4 Interrupts / SMI# The PCH SMBus controller uses PIRQB# as its interrupt pin. However, the system can alternatively be set up to generate SMI# instead of an interrupt, by setting the SMBUS_SMI_EN bit (D31:F0:Offset 40h:Bit 1). Datasheet 217 Functional Description Table 5-50 and Table 5-51 specify how the various enable bits in the SMBus function control the generation of the interrupt, Host and Slave SMI, and Wake internal signals. The rows in the tables are additive, which means that if more than one row is true for a particular scenario then the Results for all of the activated rows will occur. Table 5-49. Enable for SMBALERT# Event INTREN (Host Control I/O Register, Offset 02h, Bit 0) SMB_SMI_EN (Host Configuration Register, D31:F3:Offset 40h, Bit 1) SMBALERT_DIS (Slave Command I/O Register, Offset 11h, Bit 2) X X X Wake generated X 1 0 Slave SMI# generated (SMBUS_SMI_STS) 1 0 0 Interrupt generated SMBALERT# asserted low (always reported in Host Status Register, Bit 5) Result Table 5-50. Enables for SMBus Slave Write and SMBus Host Events INTREN (Host Control I/O Register, Offset 02h, Bit 0) SMB_SMI_EN (Host Configuration Register, D31:F3:Offset 40h, Bit 1) Slave Write to Wake/SMI# Command X X Wake generated when asleep. Slave SMI# generated when awake (SMBUS_SMI_STS). Slave Write to SMLINK_SLAVE_SMI Command X X Slave SMI# generated when in the S0 state (SMBUS_SMI_STS) Any combination of Host Status Register [4:1] asserted 0 X None 1 0 Interrupt generated 1 1 Host SMI# generated Event Event Table 5-51. Enables for the Host Notify Command HOST_NOTIFY_INTREN (Slave Control I/O Register, Offset 11h, Bit 0) SMB_SMI_EN (Host Config Register, D31:F3:Off40h, Bit 1) HOST_NOTIFY_WKEN (Slave Control I/O Register, Offset 11h, Bit 1) 0 X 0 None X X 1 Wake generated 1 0 X Interrupt generated 1 1 X Slave SMI# generated (SMBUS_SMI_STS) 5.22.5 Result SMBALERT# SMBALERT# is multiplexed with GPIO[11]. When enable and the signal is asserted, the PCH can generate an interrupt, an SMI#, or a wake event from S1-S5. 218 Datasheet Functional Description 5.22.6 SMBus CRC Generation and Checking If the AAC bit is set in the Auxiliary Control register, the PCH automatically calculates and drives CRC at the end of the transmitted packet for write cycles, and will check the CRC for read cycles. It will not transmit the contents of the PEC register for CRC. The PEC bit must not be set in the Host Control register. If this bit is set, unspecified behavior will result. If the read cycle results in a CRC error, the DEV_ERR bit and the CRCE bit in the Auxiliary Status register at Offset 0Ch will be set. 5.22.7 SMBus Slave Interface The PCH SMBus Slave interface is accessed using the SMBus. The SMBus slave logic will not generate or handle receiving the PEC byte and will only act as a Legacy Alerting Protocol device. The slave interface allows the PCH to decode cycles, and allows an external microcontroller to perform specific actions. Key features and capabilities include: * Supports decode of three types of messages: Byte Write, Byte Read, and Host Notify. * Receive Slave Address register: This is the address that the PCH decodes. A default value is provided so that the slave interface can be used without the processor having to program this register. * Receive Slave Data register in the SMBus I/O space that includes the data written by the external microcontroller. * Registers that the external microcontroller can read to get the state of the PCH. * Status bits to indicate that the SMBus slave logic caused an interrupt or SMI# due to the reception of a message that matched the slave address. -- Bit 0 of the Slave Status Register for the Host Notify command -- Bit 16 of the SMI Status Register (Section 12.8.3.8) for all others Note: The external microcontroller should not attempt to access the PCH SMBus slave logic until either: -- 800 milliseconds after both: RTCRST# is high and RSMRST# is high, OR -- The PLTRST# de-asserts If a master leaves the clock and data bits of the SMBus interface at 1 for 50 s or more in the middle of a cycle, the PCH slave logic's behavior is undefined. This is interpreted as an unexpected idle and should be avoided when performing management activities to the slave logic. Note: Datasheet When an external microcontroller accesses the SMBus Slave Interface over the SMBus a translation in the address is needed to accommodate the least significant bit used for read/write control. For example, if the PCH slave address (RCV_SLVA) is left at 44h (default), the external micro controller would use an address of 88h/89h (write/read). 219 Functional Description 5.22.7.1 Format of Slave Write Cycle The external master performs Byte Write commands to the PCH SMBus Slave I/F. The "Command" field (bits 11:18) indicate which register is being accessed. The Data field (bits 20:27) indicate the value that should be written to that register. Table 5-52 has the values associated with the registers. Table 5-52. Slave Write Registers Register 0 1-3 Note: Function Command Register. See Table 5-53 for legal values written to this register. Reserved 4 Data Message Byte 0 5 Data Message Byte 1 6-7 Reserved 8 Reserved 9-FFh Reserved The external microcontroller is responsible to make sure that it does not update the contents of the data byte registers until they have been read by the system processor. The PCH overwrites the old value with any new value received. A race condition is possible where the new value is being written to the register just at the time it is being read. The PCH will not attempt to cover this race condition (that is, unpredictable results in this case). Table 5-53. Command Types Command Type 0 Reserved 1 WAKE/SMI#. This command wakes the system if it is not already awake. If system is already awake, an SMI# is generated. Note: The SMB_WAK_STS bit will be set by this command, even if the system is already awake. The SMI handler should then clear this bit. 2 Unconditional Powerdown. This command sets the PWRBTNOR_STS bit, and has the same effect as the Powerbutton Override occurring. 3 HARD RESET WITHOUT CYCLING: This command causes a hard reset of the system (does not include cycling of the power supply). This is equivalent to a write to the CF9h register with Bits 2:1 set to 1, but Bit 3 set to 0. 4 HARD RESET SYSTEM. This command causes a hard reset of the system (including cycling of the power supply). This is equivalent to a write to the CF9h register with Bits 3:1 set to 1. 5 Disable the TCO Messages. This command will disable the PCH from sending Heartbeat and Event messages (as described in Section 5.15). Once this command has been executed, Heartbeat and Event message reporting can only be re-enabled by assertion and de-assertion of the RSMRST# signal. 6 WD RELOAD: Reload watchdog timer. 7 Reserved 8 SMLINK_SLV_SMI. When the PCH detects this command type while in the S0 state, it sets the SMLINK_SLV_SMI_STS bit (see Section 12.9.5). This command should only be used if the system is in an S0 state. If the message is received during S1-S5 states, the PCH acknowledges it, but the SMLINK_SLV_SMI_STS bit does not get set. Note: It is possible that the system transitions out of the S0 state at the same time that the SMLINK_SLV_SMI command is received. In this case, the SMLINK_SLV_SMI_STS bit may get set but not serviced before the system goes to sleep. Once the system returns to S0, the SMI associated with this bit would then be generated. Software must be able to handle this scenario. 9-FFh 220 Description Reserved. Datasheet Functional Description 5.22.7.2 Format of Read Command The external master performs Byte Read commands to the PCH SMBus Slave interface. The "Command" field (bits 18:11) indicate which register is being accessed. The Data field (bits 30:37) contain the value that should be read from that register. Table 5-54. Slave Read Cycle Format Bit 1 2-8 Description Driven by Comment Start External Microcontroller Slave Address - 7 bits External Microcontroller Must match value in Receive Slave Address register Always 0 9 Write External Microcontroller 10 ACK PCH Command code - 8 bits External Microcontroller 19 ACK PCH 20 Repeated Start External Microcontroller Slave Address - 7 bits External Microcontroller Must match value in Receive Slave Address register Always 1 11-18 21-27 28 Read External Microcontroller 29 ACK PCH 30-37 Data Byte PCH 38 NOT ACK External Microcontroller 39 Stop External Microcontroller Indicates which register is being accessed. See Table 5-55 for a list of implemented registers. Value depends on register being accessed. See Table 5-55 for a list of implemented registers. Table 5-55. Data Values for Slave Read Registers (Sheet 1 of 2) Register Bits Description 0 7:0 Reserved for capabilities indication. Should always return 00h. Future chips may return another value to indicate different capabilities. 1 2:0 System Power State 000 = S0 001 = S1 010 = Reserved 011 = S3 100 = S4 101 = S5 110 = Reserved 111 = Reserved 7:3 Reserved 2 3 4 3:0 Reserved 7:4 Reserved 5:0 Watchdog Timer current value. The Watchdog Timer has 10 bits, but this field is only 6 bits. If the current value is greater than 3Fh, the PCH will always report 3Fh in this field. 7:6 Reserved 0 1 = The Intruder Detect (INTRD_DET) bit is set. This indicates that the system cover has probably been opened. 1 1 = BTI Temperature Event occurred. This bit will be set if the PCH THRM# input signal is active. Else this bit will read "0." 2 DOA Processor Status. This bit will be 1 to indicate that the processor is dead 3 1 = SECOND_TO_STS bit set. This bit will be set after the second time-out (SECOND_TO_STS bit) of the Watchdog Timer occurs. 6:4 7 Datasheet Reserved. Will always be 0, but software should ignore. Reflects the value of the GPIO[11]/SMBALERT# pin (and is dependent upon the value of the GPI_INV[11] bit. If the GPI_INV[11] bit is 1, then the value in this bit equals the level of the GPI[11]/SMBALERT# pin (high = 1, low = 0). If the GPI_INV[11] bit is 0, then the value of this bit will equal the inverse of the level of the GPIO[11]/SMBALERT# pin (high = 0, low = 1). 221 Functional Description Table 5-55. Data Values for Slave Read Registers (Sheet 2 of 2) 5.22.7.2.1 Register Bits 5 0 Description FWH bad bit. This bit will be 1 to indicate that the FWH read returned FFh, which indicates that it is probably blank. 1 Reserved 2 SYS_PWROK Failure Status: This bit will be 1 if the SYSPWR_FLR bit in the GEN_PMCON_2 register is set. 3 Reserved 4 Reserved 5 POWER_OK_BAD: Indicates the failure core power well ramp during boot/resume. This bit will be active if the SLP_S3# pin is de-asserted and PWROK pin is not asserted. 6 Thermal Trip: This bit will shadow the state of processor Thermal Trip status bit (CTS) (16.2.1.2, GEN_PMCON_2, bit 3). Events on signal will not create a event message 7 Reserved: Default value is "X" Note: Software should not expect a consistent value when this bit is read through SMBUS/SMLink 6 7:0 Contents of the Message 1 register. Refer to Section 12.9.8 for the description of this register. 7 7:0 Contents of the Message 2 register. Refer to Section 12.9.8 for the description of this register. 8 7:0 Contents of the TCO_WDCNT register. Refer to Section 12.9.9 for the description of this register. 9 7:0 Seconds of the RTC A 7:0 Minutes of the RTC B 7:0 Hours of the RTC C 7:0 "Day of Week" of the RTC D 7:0 "Day of Month" of the RTC E 7:0 Month of the RTC F 7:0 Year of the RTC 10h-FFh 7:0 Reserved Behavioral Notes According to SMBus protocol, Read and Write messages always begin with a Start bit - Address- Write bit sequence. When the PCH detects that the address matches the value in the Receive Slave Address register, it will assume that the protocol is always followed and ignore the Write bit (Bit 9) and signal an Acknowledge during bit 10. In other words, if a Start -Address-Read occurs (which is illegal for SMBus Read or Write protocol), and the address matches the PCH's Slave Address, the PCH will still grab the cycle. Also according to SMBus protocol, a Read cycle contains a Repeated Start-Address- Read sequence beginning at Bit 20. Once again, if the Address matches the PCH's Receive Slave Address, it will assume that the protocol is followed, ignore bit 28, and proceed with the Slave Read cycle. Note: An external microcontroller must not attempt to access the PCH's SMBus Slave logic until at least 1 second after both RTCRST# and RSMRST# are de-asserted (high). 5.22.7.3 Slave Read of RTC Time Bytes The PCH SMBus slave interface allows external SMBus master to read the internal RTC's time byte registers. 222 Datasheet Functional Description The RTC time bytes are internally latched by the PCH's hardware whenever RTC time is not changing and SMBus is idle. This ensures that the time byte delivered to the slave read is always valid and it does not change when the read is still in progress on the bus. The RTC time will change whenever hardware update is in progress, or there is a software write to the RTC time bytes. The PCH SMBus slave interface only supports Byte Read operation. The external SMBus master will read the RTC time bytes one after another. It is software's responsibility to check and manage the possible time rollover when subsequent time bytes are read. For example, assuming the RTC time is 11 hours: 59 minutes: 59 seconds. When the external SMBus master reads the hour as 11, then proceeds to read the minute, it is possible that the rollover happens between the reads and the minute is read as 0. This results in 11 hours: 0 minute instead of the correct time of 12 hours: 0 minutes. Unless it is certain that rollover will not occur, software is required to detect the possible time rollover by reading multiple times such that the read time bytes can be adjusted accordingly if needed. 5.22.7.4 Format of Host Notify Command The PCH tracks and responds to the standard Host Notify command as specified in the System Management Bus (SMBus) Specification, Version 2.0. The host address for this command is fixed to 0001000b. If the PCH already has data for a previously-received host notify command which has not been serviced yet by the host software (as indicated by the HOST_NOTIFY_STS bit), then it will NACK following the host address byte of the protocol. This allows the host to communicate non-acceptance to the master and retain the host notify address and data values for the previous cycle until host software completely services the interrupt. Note: Host software must always clear the HOST_NOTIFY_STS bit after completing any necessary reads of the address and data registers. Table 5-56 shows the Host Notify format. Table 5-56. Host Notify Format Bit 1 8:2 9 10 17:11 Driven By External Master SMB Host Address - 7 bits External Master Write External Master ACK (or NACK) PCH Comment Always 0001_000 Always 0 PCH NACKs if HOST_NOTIFY_STS is 1 Device Address - 7 bits External Master Indicates the address of the master; loaded into the Notify Device Address Register 18 Unused - Always 0 External Master 7-bit-only address; this bit is inserted to complete the byte 19 ACK PCH Data Byte Low - 8 bits External Master ACK PCH Data Byte High - 8 bits External Master 37 ACK PCH 38 Stop External Master 27:20 28 36:29 Datasheet Description Start Loaded into the Notify Data Low Byte Register Loaded into the Notify Data High Byte Register 223 Functional Description 5.23 Thermal Management 5.23.1 Thermal Sensor The PCH incorporates one on-die Digital thermal sensor (DTS) for thermal management. The thermal sensor can provide PCH temperature information to an EC or SIO device that can be used to determine how to control the fans. This thermal sensor is located near the DMI interface. The on-die thermal sensor is placed as close as possible to the hottest on-die location to reduce thermal gradients and to reduce the error on the sensor trip thresholds. The thermal sensor trip points may be programmed to generate various interrupts including SCI, SMI and other General Purpose events. 5.23.1.1 Internal Thermal Sensor Operation The internal thermal sensor reports four trip points: Aux2, Aux, Hot and Catastrophic trip points in the order of increasing temperature. Aux, Aux2 Temperature Trip Points These trip points may be set dynamically if desired and provides an interrupt to ACPI (or other software) when it is crossed in either direction. These auxiliary temperature trip points do not automatically cause any hardware throttling but may be used by software to trigger interrupts. This trip point is set below the Hot temperature trip point and responses are separately programmable from the hot temperature settings, in order to provide incrementally more aggressive actions. Aux and Aux2 trip points are fully Software programmable during system run-time. Aux2 trip point is set below the Aux temperature trip point. Hot Temperature Trip Point This trip point may be set dynamically if desired and provides an interrupt to ACPI (or other software) when it is crossed in either direction. Software could optionally set this as an Interrupt when the temperature exceeds this level setting. Hot trip does not provide any default hardware based thermal throttling, and is available only as a customer configurable interrupt when Tj,max has been reached. Catastrophic Trip Point This trip point is set at the temperature at which the PCH must be shut down immediately without any software support. The catastrophic trip point must correspond to a temperature ensured to be functional in order for the interrupt generation and Hardware response. Hardware response using THRMTRIP# would be an unconditional transition to S5. The catastrophic transition to the S5 state does not enforce a minimum time in the S5 state. It is assumed that the S5 residence and the reboot sequence cools down the system. If the catastrophic condition remains when the catastrophic power down enable bit is set by BIOS, then the system will re-enter S5. Thermometer Mode The thermometer is implemented using a counter that starts at 0 and increments during each sample point until the comparator indicates the temperature is above the current value. The value of the counter is loaded into a read-only register (Thermal Sensor Thermometer Read) when the comparator first trips. 224 Datasheet Functional Description 5.23.1.1.1 Recommended Programming for Available Trip Points There may be a 2 C offset due to thermal gradient between the hot-spot and the location of the thermal sensor. Trip points should be programmed to account for this temperature offset between the hot-spot Tj,max and the thermal sensor. Aux Trip Points should be programmed for software and firmware control using interrupts. Hot Trip Point should be set to throttle at 108 C (Tj,max) due to DTS trim accuracy adjustments. Hot trip points should also be programmed for a software response. Catastrophic Trip Point should be set to halt operation to avoid maximum Tj of about 120 C. Note: Crossing a trip point in either direction may generate several types of interrupts. Each trip point has a register that can be programmed to select the type of interrupt to be generated. Crossing a trip point is implemented as edge detection on each trip point to generate the interrupts. 5.23.1.1.2 Thermal Sensor Accuracy (Taccuracy) Taccuracy for the PCH is 5 C in the temperature range 90 C to 120 C. Taccuracy is 10 C for temperatures from 45 C - 90 C. The PCH may not operate above +108 C. This value is based on product characterization and is not ensured by manufacturing test. Software has the ability to program the Tcat, Thot, and Taux trip points, but these trip points should be selected with consideration for the thermal sensor accuracy and the quality of the platform thermal solution. Overly conservative (unnecessarily low) temperature settings may unnecessarily degrade performance due to frequent throttling, while overly aggressive (dangerously high) temperature settings may fail to protect the part against permanent thermal damage. 5.23.2 PCH Thermal Throttling Occasionally the PCH may operate in conditions that exceed its maximum operating temperature. In order to protect itself and the system from thermal failure, the PCH is capable of reducing its overall power consumption and as a result, lower its temperature. This is achieved by: * Forcing the SATA device and interface in to a lower power state * Reducing the number of active lanes on the DMI interface * Reducing the Intel Management Engine (Intel ME) clock frequency The severity of the throttling response is defined by four global PCH throttling states referred to as T-states. In each T-state, the throttling response will differ per interface, but will operate concurrently when a global T-state is activated. A T-state corresponds to a temperature range. The T-states are defined in Table 5-57. Datasheet 225 Functional Description Table 5-57. PCH Thermal Throttle States (T-states) State Description T0 Normal operation, temperature is less than the T1 trip point temperature T1 Temperature is greater than or equal to the T1 trip point temperature, but less than the T2 trip point temperature. The default temperature is Tj,max at 108 C T2 Temperature is greater than or equal to the T2 trip point temperature, but less than the T3 trip point temperature. The default temperature is 112 C T3 Temperature is greater than or equal to the T3 trip point temperature. The default temperature is 116 C Enabling of this feature requires appropriate Intel Management Engine firmware and configuration of the following registers shown in Table 5-58. Table 5-58. PCH Thermal Throttling Configuration Registers Register Name TL - Throttle Levels 5.23.3 Register Location TBARB+40h Section 22.2.10 Thermal Reporting Over System Management Link 1 Interface (SMLink1) SMLink1 interface in the PCH is the SMBus link to an optional external controller. A SMBus protocol is defined on the PCH to allow compatible devices such as Embedded Controller (EC) or SIO to obtain system thermal data from PCH sensors using the SMLink1 interface. This solution allows an external device or controller to use the system thermal data for system thermal management. Note: To enable Thermal Reporting: Set Section 22.2.4, "TSEL--Thermal Sensor Enable and Lock Register"bit 0 = 1 (Enable TS) and Section 22.2.5, "TSREL--Thermal Sensor Reporting Enable and Lock Register"bit 0 = 1 (Enable SMBus Temperature Reporting). There are two uses for the PCH's thermal reporting capability: 1. To provide system thermal data to an external controller. The controller can manage the fans and other cooling elements based on this data. In addition, the PCH can be programmed by setting appropriate bits in the Section 22.2.7, "CTT-- Catastrophic Trip Point Register", Section 22.2.8, "TAHV--Thermal Alert High Value Register" and Section 22.2.9, "TALV--Thermal Alert Low Value Register"to alert the controller when a device has gone outside of its temperature limits. The alert causes the assertion of the PCH TEMP_ALERT# (SML1ALERT#/TEMP_ALERT#/ GPIO74) signal. See Section 5.23.3.5 for more details. 2. To provide an interface between the external controller and host software. This software interface has no direct affect on the PCH's thermal collection. It is strictly a software interface to pass information or data. The PCH responds to thermal requests only when the system is in S0 or S1. Once the PCH has been programmed, it will start responding to a request while the system is in S0 or S1. To implement this thermal reporting capability, the platform is required to have appropriate BIOS support and compatible devices that support the SMBus protocol. 226 Datasheet Functional Description 5.23.3.1 Block Read Address The PCH supports the Block Read Address for reads. This address is used for reads from the PCH. * The address is set by soft straps or BIOS. It can be set to any value the platform requires. * This address only supports SMBus Block Read command and not Byte or Word Read. * The Block Read command is supported as defined in the SMBus 2.0 specification, with the command being 40h, and the byte count being provided by the PCH following the block read format in the SMBus specification. * Writes are not allowed to this address, and result in indeterminate behavior. * Packet Error Code (PEC) may be enabled or not, which is set up by BIOS. 5.23.3.2 Block Read Command The external controller may read thermal information from the PCH using the SMBus Block Read Command. Byte-read and Word-read SMBus commands are not supported. The reads use a different address than the writes. The command format follows the Block Read format of the SMBus specification. The PCH returns a single byte of data, indicating the temperature between 0 C (0x00) and 254 C (0xFE). A read of 0xFF indicates that the sensor is not yet enabled. For more information, see Section 5.23.3.3.1. 5.23.3.3 Read Data Format For each of the data fields an ERROR Code is listed below. This code indicates that the PCH failed in its access to the device. This would be for the case where the read returned no data, or some illegal value. In general that would mean the device is broken. The EC can treat the device that failed the read as broken or with some failsafe mechanism. 5.23.3.3.1 PCH Temperature The temperature readings for the PCH are 8-bit unsigned values from 0-255. The minimum granularity supported by the internal thermal sensor is 1 C. Thus, there are no fractional values for the PCH temperatures. The device returns a temperature between 0 C (0x00) and 254 C (0xFE). Devices that are not yet enabled return the value 0xFF. Note: Sensors used within the components do not support values below 0C, so this field is treated as 8 bits (0-255) absolute. 5.23.3.4 Thermal Data Update Rate The temperature values are updated every 1 ms in the PCH, so reading more often than that simply returns the same data multiple times. Also, the data may be up to 1 ms old if the external controller reads the data right before the next update window. Datasheet 227 Functional Description 5.23.3.5 Temperature Comparator and Alert The PCH has the ability to alert the external controller when temperatures are out of range. This is done using the PCH TEMP_ALERT# signal. The alert is a simple comparator. If any device's temperature is outside the limit range for that device, then the signal is asserted (electrical low). This alert does not use the SML1ALERT#. The PCH supports 2 ranges: an upper and lower limit (8 bits each, in degrees C) for the PCH temperature. The comparator checks if the device is within the specified range, including the limits. For example, a device that is at 100 degrees when the upper limit is 100 will not trigger the alert. Likewise, a device that is at 70 degrees when the lower limit is 70 will not trigger the alert. The compares are done only on devices that have been enabled by BIOS for checking. The compares are done in firmware, so all the compares are executed in one software loop and at the end, if there is any out of bound temperature, the PCH's TEMP_ALERT# signal is asserted. When the external controller sees the TEMP_ALERT# signal low, it knows the device is out of range. It can read the temperature and then change the limit for the device. It may take up to 250 ms before the actual writes cause the signal to change state. For instance, if the PCH is at 105 degrees and the limit is 100, the alert is triggered. If the controller changes the limits to 110, the TEMP_ALERT# signal may remain low until the next thermal sampling window (every 1 ms) occurs and only then go high, assuming the PCH was still within its limits. At boot, the controller can monitor the TEMP_ALERT# signal state. When BIOS has finished all the initialization and enabled the temperature comparators, the TEMP_ALERT# signal will be asserted since the default state of the limit registers is 0h; hence, when the PCH first reads temperatures, they will be out of range. This is the positive indication that the external controller may now read thermal information and get valid data. If the TEMP_ALERT# signal is enabled and not asserted within 30 seconds after PLTRST#, the external controller should assume there is a fatal error and handle accordingly. In general the TEMP_ALERT# signal will assert within a 1-4 seconds, depending on the actual BIOS implementation and flow. Note: The TEMP_ALERT# assertion is only valid when PLTRST# is de-asserted. The controller should mask the state of this signal when PLTRST# is asserted. Since the controller may be powered even when the PCH and the rest of the platform are not, the signal may glitch as power is being asserted; thus, the controller should wait until PLTRST# has de-asserted before monitoring the signal. 5.23.3.5.1 Special Conditions The external controller should have a graceful means of handling when TEMP_ALERT# asserts, and the controller reads PCH, but all temperature values are within limits. In this case, the controller should assume that by the time the controller could read the data, it had changed and moved back within the limits. 228 Datasheet Functional Description 5.23.3.6 BIOS Set Up In order for the PCH to properly report temperature and enable alerts, the BIOS must configure the PCH at boot or from suspend/resume state by writing the following information to the PCH MMIO space. This information is NOT configurable using the external controller. * Enables for PCH thermal alerts. * Enables for reading PCH temperatures. * Setting up the temperature calculation equations. 5.23.3.7 SMBus Rules The PCH may NACK an incoming SMBus transaction. In certain cases the PCH will NACK the address, and in other cases it will NACK the command depending on internal conditions (such as errors, busy conditions). Given that most of the cases are due to internal conditions, the external controller must alias a NACK of the command and a NACK of the address to the same behavior. The controller must not try to make any determination of the reason for the NACK, based on the type of NACK (command versus address). The PCH will NACK when it is enabled but busy. The external controller is required to retry up to 3 times when they are NACK'ed. In reality if there is a NACK because of the PCH being busy, in almost all cases the next read will succeed since the update internally takes very little time. In the case of a long delay, the external controller must assume that the PCH will never return good data. 5.23.3.7.1 During Block Read On the Block Read, the PCH will respect the NACK and Stop indications from the external controller, but will consider this an error case. It will recover from this case and correctly handle the next SMBus request. The PCH will honor STOP during the block read command and cease providing data. On the next Block Read, the data will start with byte 0 again. However, this is not a recommended usage except for 'emergency cases'. In general the external controller should read the entire length of data that was originally programmed. 5.23.3.7.2 Power On On the Block Read, the PCH will respect the NACK and Stop indications from the external controller, but will consider this an error case. It will recover from this case and correctly handle the next SMBus request. The PCH will honor STOP during the block read command and cease providing data. On the next Block Read, the data will start with byte 0 again. However, this is not a recommended usage except for 'emergency cases'. In general the external controller should read the entire length of data that was originally programmed. Datasheet 229 Functional Description 5.23.3.8 Case for Considerations Below are some corner cases and some possible actions that the external controller could take. A 1-byte sequence number is available to the data read by the external controller. Each time the PCH updates the thermal information it will increment the sequence number. The external controller can use this value as an indication that the thermal FW is actually operating. The sequence number will roll over to 00h when it reaches FFh. 1. Power on: The PCH will not respond to any SMBus activity (on SMLink1 interface) until it has loaded the thermal Firmware (FW), which in general would take 1-4 ms. During this period, the PCH will NACK any SMBus transaction from the external controller. The load should take 1-4 ms, but the external controller should design for 30 seconds based on long delays for S4 resume which takes longer than normal power up. This would be an extreme case, but for larger memory footprints and non-optimized recovery times, 30 seconds is a safe number to use for the timeout. Recover/Failsafe: if the PCH has not responded within 30 seconds, the external controller can assume that the system has had a major error and the external controller should ramp the fans to some reasonably high value. The only recover from this is an internal reset on the PCH, which is not visible to the external controller. Therefore the external controller might choose to poll every 10-60 seconds (some fairly long period) hereafter to see if the PCH's thermal reporting has come alive. 2. The PCH Thermal FW hangs and requires an internal reset which is not visible to the external controller. The PCH will NACK any SMBus transaction from the external controller. The PCH may not be able to respond for up to 30 seconds while the FW is being reset and reconfigured. The external controller could choose to poll every 1-10 seconds to see if the thermal FW has been successfully reset and is now providing data. General recovery for this case is about 1 second, but 30 seconds should be used by the external controller at the time-out. Recovery/Failsafe: same as in case #1. 3. Fatal PCH error, causes a global reset of all components. When there is a fatal PCH error, a global reset may occur, and then case #1 applies. The external controller can observe, if desired, PLTRST# assertion as an indication of this event. 4. The PCH thermal FW fails or is hung, but no reset occurs The sequence number will not be updated, so the external controller knows to go to failsafe after some number of reads (8 or so) return the same sequence number. The external controller could choose to poll every 1-10 seconds to see if the thermal FW has been successfully reset and working again. In the absence of other errors, the updates for the sequence number should never be longer than 400 ms, so the number of reads needed to indicate that there is a hang should be at around 2 seconds. But when there is an error, the sequence number may not get updated for seconds. In the case that the 230 Datasheet Functional Description external controller sees a NACK from the PCH, then it should restart its sequence counter, or otherwise be aware that the NACK condition needs to be factored into the sequence number usage. The use of sequence numbers is not required, but is provided as a means to ensure correct PCH FW operation. 5. When the PCH updates the Block Read data structure, the external controller gets a NACK during this period. To ensure atomicity of the SMBus data read with respect to the data itself, when the data buffer is being updated, the PCH will NACK the Block Read transaction. The update is only a few micro-seconds, so very short in terms of SMBus polling time; therefore, the next read should be successful. The external controller should attempt 3 reads to handle this condition before moving on. If the Block read has started (that is, the address is ACK'ed) then the entire read will complete successfully, and the PCH will update the data only after the SMBus read has completed. 6. System is going from S0 to S3/S4/S5. The thermal monitoring FW is fully operational if the system is in S0/S1, so the following only applies to S3/S4/S5. When the PCH detects the OS request to go to S3/S4/S5, it will take the SMLink1 controller offline as part of the system preparation. The external controller will see a period where its transactions are getting NACK'ed, and then see SLP_S3# assert. This period is relatively short (a couple of seconds depending on how long all the devices take to place themselves into the D3 state), and would be far less than the 30 second limit mentioned above. 7. TEMP_ALERT# - Since there can be an internal reset, the TEMP_ALERT# may get asserted after the reset. The external controller must accept this assertion and handle it. 5.23.3.8.1 Example Algorithm for Handling Transaction One algorithm for the transaction handling could be summarized as follows. This is just an example to illustrate the above rules. There could be other algorithms that can achieve the same results. 1. Perform SMBus transaction. 2. If ACK, then continue 3. If NACK a. Try again for 2 more times, in case the PCH is busy updating data. b. If 3 successive transactions receive NACK, then - Ramp fans, assuming some general long reset or failure - Try every 1-10 seconds to see if SMBus transactions are now working - If they start then return to step 1 - If they continue to fail, then stay in this step and poll, but keep the fans ramped up or implement some other failure recovery mechanism. Datasheet 231 Functional Description 5.24 Intel(R) High Definition Audio (Intel(R) HD Audio) Overview (D27:F0) The PCH High Definition Audio (HDA) controller communicates with the external codec(s) over the Intel High Definition Audio serial link. The controller consists of a set of DMA engines that are used to move samples of digitally encoded data between system memory and an external codec(s). The PCH implements four output DMA engines and 4 input DMA engines. The output DMA engines move digital data from system memory to a D-A converter in a codec. The PCH implements a single Serial Data Output signal (HDA_SDO) that is connected to all external codecs. The input DMA engines move digital data from the A-D converter in the codec to system memory. The PCH implements four Serial Digital Input signals (HDA_SDI[3:0]) supporting up to four codecs. Audio software renders outbound and processes inbound data to/from buffers in system memory. The location of individual buffers is described by a Buffer Descriptor List (BDL) that is fetched and processed by the controller. The data in the buffers is arranged in a predefined format. The output DMA engines fetch the digital data from memory and reformat it based on the programmed sample rate, bit/sample and number of channels. The data from the output DMA engines is then combined and serially sent to the external codecs over the Intel High Definition Audio link. The input DMA engines receive data from the codecs over the Intel High Definition Audio link and format the data based on the programmable attributes for that stream. The data is then written to memory in the predefined format for software to process. Each DMA engine moves one stream of data. A single codec can accept or generate multiple streams of data, one for each A-D or D-A converter in the codec. Multiple codecs can accept the same output stream processed by a single DMA engine. Codec commands and responses are also transported to and from the codecs using DMA engines. The PCH HD Audio controller supports the Function Level Reset (FLR). 5.24.1 Intel(R) High Definition Audio (Intel(R) HD Audio) Docking (Mobile Only) 5.24.1.1 Dock Sequence This sequence is followed when the system is running and a docking event occurs. 1. Since the PCH supports docking, the Docking Supported (DCKSTS. DS) bit defaults to a 1. POST BIOS and ACPI BIOS software uses this bit to determine if the HD Audio controller supports docking. BIOS may write a 0 to this R/WO bit during POST to effectively turn off the docking feature. 2. After reset in the undocked quiescent state, the Dock Attach (DCKCTL.DA) bit and the Dock Mate (DCKSTS.DM) bit are both de-asserted. The HDA_DOCK_EN# signal is de-asserted and HDA_DOCK_RST# is asserted. Bit Clock, SYNC and SDO signals may or may no be running at the point in time that the docking event occurs. 3. The physical docking event is signaled to ACPI BIOS software using ACPI control methods. This is normally done through a GPIO signal on the PCH and is outside the scope of this section of the specification. 4. ACPI BIOS software first checks that the docking is supported using DCKSTS.DS=1 and that the DCKSTS.DM=0 and then initiates the docking sequence by writing a 1 to the DCKCTL.DA bit. 232 Datasheet Functional Description 5. The HD Audio controller then asserts the HDA_DOCK_EN# signal so that the Bit Clock signal begins toggling to the dock codec. HDA_DOCK_EN# shall be asserted synchronously to Bit Clock and timed such that Bit Clock is low, SYNC is low, and SDO is low. Pull-down resistors on these signals in the docking station discharge the signals low so that when the state of the signal on both sides of the switch is the same when the switch is turned on. This reduces the potential for charge coupling glitches on these signals. In the PCH the first 8 bits of the Command field are "reserved" and always driven to 0s. This creates a predictable point in time to always assert HDA_DOCK_EN#. The HD Audio link reset exit specification that requires that SYNC and SDO be driven low during Bit Clock startup is not ensured. Note also that the SDO and Bit Clock signals may not be low while HDA_DOCK_RST# is asserted which also violates the specification. 6. After the controller asserts HDA_DOCK_EN# it waits for a minimum of 2400 Bit Clocks (100 s) and then de-asserts HDA_DOCK_RST#. This is done in such a way to meet the HD Audio link reset exit specification. HDA_DOCK_RST# de-assertion should be synchronous to Bit Clock and timed such that there are least 4 full Bit ClockS from the de-assertion of HDA_DOCK_RST# to the first frame SYNC assertion. 7. The Connect/Turnaround/Address Frame hardware initialization sequence will now occur on the dock codecs' SDI signals. A dock codec is detected when SDI is high on the last Bit Clock cycle of the Frame Sync of a Connect Frame. The appropriate bit(s) in the State Change Status (STATESTS) register will be set. The Turnaround and Address Frame initialization sequence then occurs on the dock codecs' SDI(s). 8. After this hardware initialization sequence is complete (approximately 32 frames), the controller hardware sets the DCKSTS.DM bit to 1 indicating that the dock is now mated. ACPI BIOS polls the DCKSTS.DM bit and when it detects it is set to 1, conveys this to the OS through a plug-N-play IRP. This eventually invokes the HD Audio Bus Driver, which then begins it's codec discovery, enumeration, and configuration process. 9. Alternatively to step #8, the HD Audio Bus Driver may choose to enable an interrupt by setting the WAKEEN bits for SDINs that didn't originally have codecs attached to them. When a corresponding STATESTS bit gets set an interrupt will be generated. In this case the HD Audio Bus Driver is called directly by this interrupt instead of being notified by the plug-N-play IRP. 10. Intel HD Audio Bus Driver software "discovers" the dock codecs by comparing the bits now set in the STATESTS register with the bits that were set prior to the docking event. 5.24.1.2 Exiting D3/CRST# When Docked 1. In D3/CRST#, CRST# is asserted by the HD Audio Bus Driver. CRST# asserted resets the dock state machines, but does not reset the DCKCTL.DA bit. Because the dock state machines are reset, the dock is electrically isolated (HDA_DOCK_EN# de-asserted) and DOCK_RST# is asserted. 2. The Bus Driver clears the STATESTS bits, then de-asserts CRST#, waits approximately 7 ms, then checks the STATESTS bits to see which codecs are present. 3. When CRST# is de-asserted, the dock state machine detects that DCKCTL.DA is still set and the controller hardware sequences through steps to electrically connect the dock by asserting HDA_DOCK_EN# and then eventually de-asserts DOCK_RST#. This completes within the 7 ms mentioned in step 2). Datasheet 233 Functional Description 4. The Bus Driver enumerates the codecs present as indicated using the STATESTS bits. 5. This process did not require BIOS or ACPI BIOS to set the DCKCTL.DA bit. 5.24.1.3 Cold Boot/Resume from S3 When Docked 1. When booting and resuming from S3, PLTRST# switches from asserted to deasserted. This clears the DCKCTL.DA bit and the dock state machines. Because the dock state machines are reset, the dock is electrically isolated (HDA_DOCK_EN# de-asserted) and DOCK_RST# is asserted. 2. POST BIOS detects that the dock is attached and sets the DCKCTL.DA bit to 1. At this point CRST# is still asserted so the dock state machine will remain in its reset state. 3. The Bus Driver clears the STATESTS bits, then de-asserts CRST#, waits approximately 7 ms, then checks the STATESTS bits to see which codecs are present. 4. When CRST# is de-asserted, the dock state machine detects that DCKCTL.DA is still set and the controller hardware sequences through steps to electrically connect the dock by asserting HDA_DOCK_EN# and then eventually de-asserts DOCK_RST#. This completes within the 7 ms mentioned in step 3). 5. The Bus Driver enumerates the codecs present as indicated using the STATESTS bits. 5.24.1.4 Undock Sequence There are two possible undocking scenarios. The first is the one that is initiated by the user that invokes software and gracefully shuts down the dock codecs before they are undocked. The second is referred to as the "surprise undock" where the user undocks while the dock codec is running. Both of these situations appear the same to the controller as it is not cognizant of the "surprise removal". But both sequences will be discussed here. 5.24.1.5 Normal Undock 1. In the docked quiescent state, the Dock Attach (DCKCTL.DA) bit and the Dock Mate (DCKSTS.DM) bit are both asserted. The HDA_DOCK_EN# signal is asserted and HDA_DOCK_RST# is de-asserted. 2. The user initiates an undock event through the GUI interface or by pushing a button. This mechanism is outside the scope of this section of the document. Either way ACPI BIOS software will be invoked to manage the undock process. 3. ACPI BIOS will call the HD Audio Bus Driver software in order to halt the stream to the dock codec(s) prior to electrical undocking. If the HD Audio Bus Driver is not capable of halting the stream to the docked codec, ACPI BIOS will initiate the hardware undocking sequence as described in the next step while the dock stream is still running. From this standpoint, the result is similar to the "surprise undock" scenario where an audio glitch may occur to the docked codec(s) during the undock process. 4. The ACPI BIOS initiates the hardware undocking sequence by writing a 0 to the DCKCTL.DA bit. 5. The HD Audio controller asserts HDA_DOCK_RST#. HDA_DOCK_RST# assertion shall be synchronous to Bit Clock. There are no other timing requirements for HDA_DOCK_RST# assertion. The HD Audio link reset specification requirement that the last Frame sync be skipped will not be met. 234 Datasheet Functional Description 6. A minimum of 4 Bit Clocks after HDA_DOCK_RST# the controller will de-assert HDA_DOCK_EN# to isolate the dock codec signals from the PCH HD Audio link signals. HDA_DOCK_EN# is de-asserted synchronously to Bit Clock and timed such that Bit Clock, SYNC, and SDO are low. 7. After this hardware undocking sequence is complete the controller hardware clears the DCKSTS.DM bit to 0 indicating that the dock is now un-mated. ACPI BIOS software polls DCKSTS.DM and when it sees DM set, conveys to the end user that physical undocking can proceed. The controller is now ready for a subsequent docking event. 5.24.1.6 Surprise Undock 1. In the surprise undock case the user undocks before software has had the opportunity to gracefully halt the stream to the dock codec and initiate the hardware undock sequence. 2. A signal on the docking connector is connected to the switch that isolates the dock codec signals from the PCH HD Audio link signals (DOCK_DET#). When the undock event begins to occur the switch will be put into isolate mode. 3. The undock event is communicated to the ACPI BIOS using ACPI control methods that are outside the scope of this section of the document. 4. ACPI BIOS software writes a 0 to the DCKCTL.DA bit. ACPI BIOS then calls the HD Audio Bus Driver using plug-N-play IRP. The Bus Driver then posthumously cleans up the dock codec stream. 5. The HD Audio controller hardware is oblivious to the fact that a surprise undock occurred. The flow from this point on is identical to the normal undocking sequence described in Section 5.24.1.5 starting at step 3). It finishes with the hardware clearing the DCKSTS.DM bit set to 0 indicating that the dock is now un-mated. The controller is now ready for a subsequent docking event. 5.24.1.7 Interaction between Dock/Undock and Power Management States When exiting from S3, PLTRST# will be asserted. The POST BIOS is responsible for initiating the docking sequence if the dock is already attached when PLTRST# is deasserted. POST BIOS writes a 1 to the DCKCTL.DA bit prior to the HD Audio driver deasserting CRTS# and detecting and enumerating the codecs attached to the HDA_DOCK_RST# signal. The HD Audio controller does not directly monitor a hardware signal indicating that a dock is attached. Therefore a method outside the scope of this document must be used to cause the POST BIOS to initiate the docking sequence. When exiting from D3, CRST# will be asserted. When CRST# bit is "0" (asserted), the DCKCTL.DA bit is not cleared. The dock state machine will be reset such that HDA_DOCK_EN# will be de-asserted, HDA_DOCK_RST# will be asserted and the DCKSTS.DM bit will be cleared to reflect this state. When the CRST# bit is de-asserted, the dock state machine will detect that DCKCTL.DA is set to "1" and will begin sequencing through the dock process. This does not require any software intervention. 5.24.1.8 Relationship between HDA_DOCK_RST# and HDA_RST# HDA_RST# will be asserted when a PLTRST# occurs or when the CRST# bit is 0. As long as HDA_RST# is asserted, the DOCK_RST# signal will also be asserted. Datasheet 235 Functional Description When PLTRST# is asserted, the DCKCTL.DA and DCKSTS.DM bits will be get cleared to their default state "0s", and the dock state machine will be reset such that HDA_DOCK_EN# will be de-asserted, and HDA_DOCK_RST# will be asserted. After any PLTRST#, POST BIOS software is responsible for detecting that a dock is attached and then writing a "1" to the DCKCTL.DA bit prior to the HD Audio Bus Driver de-asserting CRST#. When CRST# bit is "0" (asserted), the DCKCTL.DA bit is not cleared. The dock state machine will be reset such that HDA_DOCK_EN# will be de-asserted, HDA_DOCK_RST# will be asserted and the DCKSTS.DM bit will be cleared to reflect this state. When the CRST# bit is de-asserted, the dock state machine will detect that DCKCTL.DA is set to "1" and will begin sequencing through the dock process. This does not require any software intervention 5.25 Intel(R) Management Engine (Intel(R) ME) and Intel(R) Management Engine Firmware (Intel(R) ME FW) 9.0 Key properties of Intel Management Engine (Intel ME): * Connectivity -- Integration into I/O subsystem of PCH -- Delivery of advanced I/O functions * Security -- More secure (Intel root of trust) and isolated execution -- Increased security of flash file system * Modularity and Partitioning -- OSV, VMM and SW Independence -- Rapid response to competitive changes * Power -- Always-On Always Connected -- Advanced functions in low power S3-S4-S5 operation -- OS independent PM and thermal heuristics Intel ME FW provides a variety of services that range from low-level hardware initialization and provisioning to high-level end-user software based IT manageability services. One of Intel ME FW's most established and recognizable features is Intel Active Management Technology (Intel(R) AMT). Intel Active Management Technology is a set of advanced manageability features developed to meet the evolving demands placed on IT to manage a network infrastructure. Intel(R) AMT reduces the Total Cost of Ownership (TCO) for IT management through features such as asset tracking, remote manageability, and robust policy-based security, resulting in fewer desk-side visits and reduced incident support durations. Intel AMT extends the manageability capability for IT through Out Of Band (OOB), allowing asset information, remote diagnostics, recovery, and contain capabilities to be available on client systems even when they are in a low power, or "off" state, or in situations when the operating system is hung. 236 Datasheet Functional Description Figure 5-14. PCH Intel(R) Management Engine (Intel(R) ME) High-Level Block Diagram 5.25.1 Intel(R) Management Engine (Intel(R) ME) Requirements The following list of components compose the Intel ME hardware infrastructure: * The Intel ME is the general purpose controller that resides in the PCH. It operates in parallel to, and is resource-isolated from, the host processor. * The SPI flash device stores Intel ME Firmware code that is executed by the Intel ME for its operations. The PCH controls the flash device through the SPI interface and internal logic. * In the M0 power state, the Intel ME FW code is loaded from SPI flash into DRAM and cached in secure and isolated SRAM. In order to interface with DRAM, the Intel ME utilizes the integrated memory controller (IMC) present in the processor. DMI serves as the interface for communication between the IMC and Intel ME. This interfacing occurs in only M0 power state. In the lower Intel ME power state, M3, code is executed exclusively from secure and isolated Intel ME local RAM. * The LAN controller embedded in the PCH as well as the Intel Gigabit Platform LAN Connect device are required for Intel ME and Intel(R) AMT network connectivity. * BIOS provides asset detection and POST diagnostics (BIOS and Intel AMT can optionally share same flash memory device) * An ISV software package, such as LANDesk*, Altiris*, or Microsoft* SMS, can be used to take advantage of the platform manageability capabilities of Intel AMT. Datasheet 237 Functional Description 5.26 Serial Peripheral Interface (SPI) The Serial Peripheral Interface (SPI) is a 4-pin interface that provides a lower-cost alternative for system flash versus the Firmware Hub on the LPC bus. The 4-pin SPI interface consists of clock (CLK), master data out (Master Out Slave In (MOSI)), master data in (Master In Slave Out (MISO)) and an active low chip select (SPI_CS[1:0]#). SPI also adds 2 extra pins SPI_IO2 and SPI_IO3 for Quad I/O operation. The PCH supports up to two SPI flash devices using two separate Chip Select pins. Each SPI flash device can be up to 16 MB. The PCH SPI interface supports 20 MHz, 33 MHz, and 50 MHz SPI devices. A SPI Flash device on with Chip Select 0 with a valid descriptor MUST be attached directly to the PCH. Note: When operating at 50 MHz, because of the 40% duty cycle PCH must use by dividing down from a 125 MHz clock, the PCH SPI Flash Controller cannot meet the minimum high timing requirements of a 50 MHz SPI Flash component and a 66 MHz rated or faster SPI Flash component must be used. The PCH supports fast read which consist of: 1. Dual Output Fast Read (Single Input Dual Output) 2. Dual I/O Fast Read (Dual Input Dual Output) 3. Quad Output Fast Read (Single Input Quad Output) 4. Quad I/O Fast Read (Quad Input Quad Output) Fast Read function will be enabled if the particular SPI part supports one of the function mentioned above along with support for SFDP (Serial Flash Discoverable Parameter). PCH adds support for SFDP. SFDP is a JEDEC* standard that provides consistent method for describing functional and feature capabilities of serial flash devices in a standard set of internal parameter table. PCH SPI controller reads the internal parameter table and enables divergent features of multiple SPI vendor parts. PCH adds third chip select SPI_CS2# for TPM support over SPI. TPM Bus will use SPI_CLK, SPI_MISO, SPI_MOSI and SPI_CS2# SPI signals. Note: Communication on the SPI bus is done with a Master - Slave protocol. The Slave is connected to the PCH and is implemented as a tri-state bus.If Boot BIOS Strap ='00' then LPC is selected as the location for BIOS. BIOS may still be placed on LPC, but all platforms with the PCH require a SPI flash connected directly to the PCH's SPI bus with a valid descriptor connected to Chip Select 0 in order to boot. Note: When SPI is selected by the Boot BIOS Destination Strap and a SPI device is detected by the PCH, LPC based BIOS flash is disabled. 5.26.1 SPI Supported Feature Overview SPI Flash on the PCH has two operational modes, descriptor and non-descriptor. 5.26.1.1 Non-Descriptor Mode Non-Descriptor Mode is not supported as a valid flash descriptor is required for all PCH Platforms. 238 Datasheet Functional Description 5.26.1.2 Descriptor Mode Descriptor Mode is required for all SKUs of the PCH. It enables many features of the chipset: * Integrated Gigabit Ethernet and Host processor for Gigabit Ethernet Software * Intel Active Management Technology * Intel Management Engine Firmware * PCI Express* root port configuration * Supports up to two SPI components using two separate chip select pins * Hardware enforced security restricting master accesses to different regions * Chipset Soft Strap regions provides the ability to use Flash NVM as an alternative to hardware pull-up/pull-down resistors for the PCH and processor * Supports the SPI Fast Read instruction and frequencies of up to 50 MHz * Support Single Input, Dual Output Fast read * Uses standardized Flash Instruction Set 5.26.1.2.1 SPI Flash Regions In Descriptor Mode the Flash is divided into five separate regions: Region Content 0 Flash Descriptor 1 BIOS 2 Intel Management Engine 3 Gigabit Ethernet 4 Platform Data Only three masters can access the four regions: Host processor running BIOS code, Integrated Gigabit Ethernet and Host processor running Gigabit Ethernet Software, and Intel Management Engine. The Flash Descriptor is in Region 0 and it must be located in the first sector of Device 0 (Offset 0). Flash Region Sizes SPI flash space requirements differ by platform and configuration. The Flash Descriptor requires one 4 KB or larger block. GbE requires two 4 KB or larger blocks. The amount of flash space consumed is dependent on the erase granularity of the flash part and the platform requirements for the Intel ME and BIOS regions. The Intel ME region contains firmware to support Intel Active Management Technology and other Intel ME capabilities. Table 5-59. Region Size versus Erase Granularity of Flash Components Region Datasheet Size with 4 KB Blocks Size with 8 KB Blocks Size with 64 KB Blocks Descriptor 4 KB 8 KB 64 KB GbE 8 KB 16 KB 128 KB BIOS Varies by Platform Varies by Platform Varies by Platform Intel ME Varies by Platform Varies by Platform Varies by Platform 239 Functional Description 5.26.2 Flash Descriptor The maximum size of the Flash Descriptor is 4 KB. If the block/sector size of the SPI flash device is greater than 4 KB, the flash descriptor will only use the first 4 KB of the first block. The flash descriptor requires its own block at the bottom of memory (00h). The information stored in the Flash Descriptor can only be written during the manufacturing process as its read/write permissions must be set to Read only when the computer leaves the manufacturing floor. The Flash Descriptor is made up of eleven sections (see Figure 5-15). Figure 5-15. Flash Descriptor Sections 4KB OEM Section Descriptor Upper MAP Management Engine VSCC Table Reserved PCH Soft Straps Master Region Component Descriptor MAP 10 h Signature 1. The Flash signature selects Descriptor Mode as well as verifies if the flash is programmed and functioning. The data at the bottom of the flash (offset 10h) must be 0FF0A55Ah in order to be in Descriptor mode. 2. The Descriptor map has pointers to the other five descriptor sections as well as the size of each. 3. The component section has information about the SPI flash in the system including: the number of components, density of each, illegal instructions (such as chip erase), and frequencies for read, fast read and write/erase instructions. 240 Datasheet Functional Description 4. The Region section points to the three other regions as well as the size of each region. 5. The master region contains the security settings for the flash, granting read/write permissions for each region and identifying each master by a requestor ID. See Section 5.26.2.1 for more information. 6 & 7. The processor and PCH soft strap sections contain processor and PCH configurable parameters. 8. The Reserved region between the top of the processor strap section and the bottom of the OEM Section is reserved for future chipset usages. 9. The Descriptor Upper MAP determines the length and base address of the Management Engine VSCC Table. 10. The Management Engine VSCC Table holds the JEDEC ID and the VSCC information of the entire SPI Flash supported by the NVM image. 11. OEM Section is 256 Bytes reserved at the top of the Flash Descriptor for use by OEM. 5.26.2.1 Descriptor Master Region The master region defines read and write access setting for each region of the SPI device. The master region recognizes three masters: BIOS, Gigabit Ethernet, and Management Engine. Each master is only allowed to do direct reads of its primary regions. Table 5-60. Region Access Control Table Master Read/Write Access Processor and BIOS Intel(R) ME N/A N/A N/A Processor and BIOS can always read from and write to BIOS Region Read / Write Read / Write Management Engine Read / Write Intel(R) ME can always read from and write to Intel ME Region Read / Write Gigabit Ethernet Read / Write Read / Write GbE software can always read from and write to GbE region N/A N/A N/A Region Descriptor BIOS Platform Data Region 5.26.3 GbE Controller Flash Access There are two types of flash accesses: Direct Access: * Masters are allowed to do direct read only of their primary region -- Gigabit Ethernet region can only be directly accessed by the Gigabit Ethernet controller. Gigabit Ethernet software must use Program Registers to access the Gigabit Ethernet region. * Master's Host or Management Engine virtual read address is converted into the SPI Flash Linear Address (FLA) using the Flash Descriptor Region Base/Limit registers Datasheet 241 Functional Description Program Register Access: * Program Register Accesses are not allowed to cross a 4 KB boundary and can not issue a command that might extend across two components * Software programs the FLA corresponding to the region desired -- Software must read the devices Primary Region Base/Limit address to create a FLA. 5.26.3.1 Direct Access Security * Requester ID of the device must match that of the primary Requester ID in the Master Section * Calculated Flash Linear Address must fall between primary region base/limit * Direct Write not allowed * Direct Read Cache contents are reset to "0s" on a read from a different master 5.26.3.2 Register Access Security * Only primary region masters can access the registers Note: Processor running Gigabit Ethernet software can access Gigabit Ethernet registers * Masters are only allowed to read or write those regions they have read/write permission * Using the Flash Region Access Permissions, one master can give another master read/write permissions to their area * Using the five Protected Range registers, each master can add separate read/write protection above that granted in the Flash Descriptor for their own accesses -- Example: BIOS may want to protect different regions of BIOS from being erased -- Ranges can extend across region boundaries 5.26.4 Serial Flash Device Compatibility Requirements A variety of serial flash devices exist in the market. For a serial flash device to be compatible with the PCH SPI bus, it must meet the minimum requirements detailed in the following sections. Note: All PCH platforms have require Intel Management Engine Firmware. 5.26.4.1 PCH SPI Based BIOS Requirements A serial flash device must meet the following minimum requirements when used explicitly for system BIOS storage. * Erase size capability of at least one of the following: 64 Kbytes, 8 Kbytes, 4 Kbytes, or 256 bytes. * Device must support multiple writes to a page without requiring a preceding erase cycle (Refer to Section 5.26.5) * Serial flash device must ignore the upper address bits such that an address of FFFFFFh aliases to the top of the flash memory. 242 Datasheet Functional Description * SPI Compatible Mode 0 support (clock phase is 0 and data is latched on the rising edge of the clock). * If the device receives a command that is not supported or incomplete (less than 8 bits), the device must complete the cycle gracefully without any impact on the flash content. * An erase command (page, sector, block, chip, and so on) must set all bits inside the designated area (page, sector, block, chip, and so on) to 1 (Fh). * Status Register bit 0 must be set to 1 when a write, erase or write to status register is in progress and cleared to 0 when a write or erase is NOT in progress. * Devices requiring the Write Enable command must automatically clear the Write Enable Latch at the end of Data Program instructions. * Byte write must be supported. The flexibility to perform a write between 1 byte to 64 bytes is recommended. * Hardware Sequencing requirements are optional in BIOS only platforms. * SPI flash parts that do not meet Hardware sequencing command set requirements may work in BIOS only platforms using software sequencing. 5.26.4.2 Integrated LAN Firmware SPI Flash Requirements A serial flash device that will be used for system BIOS and Integrated LAN or Integrated LAN only must meet all the SPI Based BIOS Requirements plus: * Hardware sequencing * 4, 8, or 64 KB erase capability must be supported. 5.26.4.2.1 SPI Flash Unlocking Requirements for Integrated LAN BIOS must ensure there is no SPI flash based read/write/erase protection on the GbE region. GbE firmware and drivers for the integrated LAN need to be able to read, write and erase the GbE region at all times. 5.26.4.3 Intel(R) Management Engine Firmware (Intel(R) ME FW) SPI Flash Requirements Intel Management Engine Firmware must meet the SPI flash based BIOS Requirements plus: * Hardware Sequencing. * Flash part must be uniform 4-KB erasable block throughout the entire device or have 64 KB blocks with the first block (lowest address) divided into 4-KB or 8-KB blocks. * Write protection scheme must meet SPI flash unlocking requirements for Intel ME. 5.26.4.3.1 SPI Flash Unlocking Requirements for Intel(R) Management Engine (Intel(R) ME) Flash devices must be globally unlocked (read, write and erase access on the ME region) from power on by writing 00h to the flash's status register to disable write protection. If the status register must be unprotected, it must use the enable write status register command 50h or write enable 06h. Datasheet 243 Functional Description Opcode 01h (write to status register) must then be used to write a single byte of 00h into the status register. This must unlock the entire part. If the SPI flash's status register has non-volatile bits that must be written to, bits [5:2] of the flash's status register must be all 0h to indicate that the flash is unlocked. If bits [5:2] return a non zero values, the Intel ME firmware will send a write of 00h to the status register. This must keep the flash part unlocked. If there is no need to execute a write enable on the status register, then opcodes 06h and 50h must be ignored. After global unlock, BIOS has the ability to lock down small sections of the flash as long as they do not involve the Intel ME or GbE region. 5.26.4.4 Hardware Sequencing Requirements Table 5-61 contains a list of commands and the associated opcodes that a SPI-based serial flash device must support in order to be compatible with hardware sequencing. Table 5-61. Hardware Sequencing Commands and Opcode Requirements Commands 5.26.4.4.1 Opcode Notes Write to Status Register 01h Writes a byte to SPI flash's status register. Enable Write to Status Register command must be run prior to this command. Program Data 02h Single byte or 64 byte write as determined by flash part capabilities and software. Read Data 03h Write Disable 04h Read Status 05h Write Enable 06h Outputs contents of SPI flash's status register Fast Read 0Bh Enable Write to Status Register 50h or 60h Enables a bit in the status register to allow an update to the status register Erase Programm able 256B, 4 Kbyte, 8 Kbyte or 64 Kbyte Full Chip Erase C7h JEDEC ID 9Fh See Section . Single Input, Dual Output Fast Read The PCH now supports the functionality of a single input, dual output fast read. Opcode and address phase are shifted in serially to the serial flash SI (Serial In) pin. Data is read out after 8 clocks (dummy bits or wait states) from the both the SI and SO pin effectively doubling the through put of each fast read output. In order to enable this functionality, both Single Input Dual Output Fast Read Supported and Fast Read supported must be enabled 5.26.4.4.2 Serial Flash Discoverable Parameters (SFDP) As the number of features keeps growing in the serial flash, the need for correct, accurate configuration increases. A method of determining configuration information is Serial Flash Discoverable Parameters (SFDP). Information such as VSCC values and flash attributes can be read directly from the flash parts. The discoverable parameter read opcode behaves like a fast read command. The opcode is 5Ah and the address cycle is 24 bits long. After the opcode 5Ah and address are clocked in, there will then be eight clocks (8 wait states) before valid data is clocked out. SFDP is a capability of the flash part; confirm with target flash vendor to see if it is supported. 244 Datasheet Functional Description In order for BIOS to take advantage of the 5Ah opcode it needs to be programmed in the Software sequencing registers. JEDEC ID Since each serial flash device may have unique capabilities and commands, the JEDEC ID is the necessary mechanism for identifying the device so the uniqueness of the device can be comprehended by the controller (master). The JEDEC ID uses the opcode 9Fh and a specified implementation and usage model. This JEDEC Standard Manufacturer and Device ID read method is defined in Standard JESD21-C, PRN03-NV. 5.26.5 Multiple Page Write Usage Model The system BIOS and Intel Management Engine firmware usage models require that the serial flash device support multiple writes to a page (minimum of 512 writes) without requiring a preceding erase command. BIOS commonly uses capabilities such as counters that are used for error logging and system boot progress logging. These counters are typically implemented by using byte-writes to `increment' the bits within a page that have been designated as the counter. The Intel ME firmware usage model requires the capability for multiple data updates within any given page. These data updates occur using byte-writes without executing a preceding erase to the given page. Both the BIOS and Intel ME firmware multiple page write usage models apply to sequential and non-sequential data writes. Note: This usage model requirement is based on any given bit only being written once from a `1' to a `0'without requiring the preceding erase. An erase would be required to change bits back to the 1 state. 5.26.5.1 Soft Flash Protection There are two types of flash protection that are not defined in the flash descriptor supported by PCH: 1. BIOS Range Write Protection 2. SMI#-Based Global Write Protection Both mechanisms are logically OR'd together such that if any of the mechanisms indicate that the access should be blocked, then it is blocked. Table 5-62 provides a summary of the mechanisms. Table 5-62. Flash Protection Mechanism Summary Mechanism Accesses Blocked Range Specific? Reset-Override or SMI#Override? Equivalent Function on FWH BIOS Range Write Protection Writes Yes Reset Override FWH Sector Protection Write Protect Writes No SMI# Override Same as Write Protect in Intel(R) ICHs for FWH A blocked command will appear to software to finish, except that the Blocked Access status bit is set in this case. Datasheet 245 Functional Description 5.26.5.2 BIOS Range Write Protection The PCH provides a method for blocking writes to specific ranges in the SPI flash when the Protected BIOS Ranges are enabled. This is achieved by checking the Opcode type information (which can be locked down by the initial Boot BIOS) and the address of the requested command against the base and limit fields of a Write Protected BIOS range. Note: Once BIOS has locked down the Protected BIOS Range registers, this mechanism remains in place until the next system reset. 5.26.5.3 SMI# Based Global Write Protection The PCH provides a method for blocking writes to the SPI flash when the Write Protected bit is cleared (that is, protected). This is achieved by checking the Opcode type information (which can be locked down by the initial Boot BIOS) of the requested command. The Write Protect and Lock Enable bits interact in the same manner for SPI BIOS as they do for the FWH BIOS. 5.26.6 Flash Device Configurations The PCH-based platform must have a SPI flash connected directly to the PCH with a valid descriptor and Intel Management Engine Firmware. BIOS may be stored in other locations such as Firmware Hub and SPI flash hooked up directly to an embedded controller for Mobile platforms. Note: This will not avoid the direct SPI flash connected to PCH requirement. 5.26.7 SPI Flash Device Recommended Pinout Table 5-63 contains the recommended serial flash device pin-out for an 8-pin device. Use of the recommended pin-out on an 8-pin device reduces complexities involved with designing the serial flash device onto a motherboard and allows for support of a common footprint usage model (refer to Section 5.26.8.1). Table 5-63. Recommended Pinout for 8-Pin Serial Flash Device Pin # Signal 1 Chips Select 2 Data Output 3 Write Protect 4 Ground 5 Data Input 6 Serial Clock 7 Hold / Reset 8 Supply Voltage Although an 8-pin device is preferred over a 16-pin device due to footprint compatibility, the following table contains the recommended serial flash device pin-out for a 16-pin SOIC. 246 Datasheet Functional Description 5.26.8 Serial Flash Device Package Table 5-64. Recommended Pinout for 16-Pin Serial Flash Device 5.26.8.1 Pin # Signal Pin # Signal 1 Hold / Reset 9 Write Protect 2 Supply Voltage 10 Ground 3 No Connect 11 No Connect 4 No Connect 12 No Connect 5 No Connect 13 No Connect 6 No Connect 14 No Connect 7 Chip Select 15 Serial Data In 8 Serial Data Out 16 Serial Clock Common Footprint Usage Model In order to minimize platform motherboard redesign and to enable platform Bill of Material (BOM) selectability, many PC System OEMs design their motherboard with a single common footprint. This common footprint allows population of a soldered down device or a socket that accepts a leadless device. This enables the board manufacturer to support, using selection of the appropriate BOM, either of these solutions on the same system without requiring any board redesign. The common footprint usage model is desirable during system debug and by flash content developers since the leadless device can be easily removed and reprogrammed without damage to device leads. When the board and flash content is mature for highvolume production, both the socketed leadless solution and the soldered down leaded solution are available through BOM selection. 5.26.8.2 Serial Flash Device Package Recommendations It is highly recommended that the common footprint usage model be supported. An example of how this can be accomplished is as follows: * The recommended pinout for 8-pin serial flash devices is used (see Section 5.26.7). * The 8-pin device is supported in either an 8-contact VDFPN (6x5 mm MLP) package or an 8-contact WSON (5x6 mm) package. These packages can fit into a socket that is land pattern compatible with the wide body SO8 package. * The 8-pin device is supported in the SO8 (150 mil) and in the wide-body SO8 (200 mil) packages. The 16-pin device is supported in the SO16 (300 mil) package. 5.26.9 PWM Outputs (Server/Workstation Only) This signal is driven as open-drain. An external pull-up resistor is integrated into the fan to provide the rising edge of the PWM output signal. The PWM output is driven low during reset, which represents 0% duty cycle to the fans. After reset de-assertion, the PWM output will continue to be driven low until one of the following occurs: * The internal PWM control register is programmed to a non-zero value by appropriate firmware. * The watchdog timer expires (enabled and set at 4 seconds by default). Datasheet 247 Functional Description * The polarity of the signal is inverted by firmware. If a PWM output will be programmed to inverted polarity for a particular fan, then the low voltage driven during reset represents 100% duty cycle to the fan. 5.26.10 TACH Inputs (Server/Workstation Only) This signal is driven as an open-collector or open-drain output from the fan. An external pull-up is expected to be implemented on the motherboard to provide the rising edge of the TACH input. This signal has analog hysteresis and digital filtering due to the potentially slow rise and fall times. This signal has a weak internal pull-up resistor to keep the input buffer from floating if the TACH input is not connected to a fan. 5.27 Feature Capability Mechanism A set of registers is included in the PCH LPC Interface (Device 31, Function 0, offset E0h-EBh) that allows the system software or BIOS to easily determine the features supported by the PCH. These registers can be accessed through LPC PCI configuration space, thus allowing for convenient single point access mechanism for chipset feature detection. This set of registers consists of: * Capability ID (FDCAP) * Capability Length (FDLEN) * Capability Version and Vendor-Specific Capability ID (FDVER) * Feature Vector (FVECT) 5.28 PCH Display Interface and Intel(R) Flexible Display Interface (Intel(R) FDI) Interconnect Display is divided between processor and PCH. The processor houses memory interface, display planes, pipes and digital display interfaces/ports while PCH has transcoder and analog display interface or port. Intel FDI connects the processor and PCH display engine. The new generation PCH integrates analog display interface only. Figure 5-16 shows the PCH Display Architecture. 248 Datasheet Functional Description Figure 5-16. PCH Display Architecture Processor Display Engine PCH Display Engine PWM Backlight Enable Panel Power Enable DMI DDC Contoller Intel FDI (Rx Side) x2 Transcoder Timing generator & FIFO CRT DAC DisplayPort AUX CH The PCH Analog Port uses an integrated 180 MHz RAMDAC that can directly drive a standard progressive scan analog monitor up to a resolution of 1920x2000 pixels with 24-bit color at 60 Hz with reduced blanking. 5.28.1 Analog Display Interface Characteristics The Analog Port provides a RGB signal output along with a HSYNC and VSYNC signal. There is an associated Display Data Channel (DDC) signal pair that is implemented using GPIO pins dedicated to the Analog Port. The intended target device is for a monitor with a VGA connector. Display devices such as LCD panels with analog inputs may work satisfactory but no functionality added to the signals to enhance that capability. Datasheet 249 Functional Description Figure 5-17. Analog Port Characteristics 5.28.1.1 Integrated RAMDAC The display function contains a RAM-based Digital-to-Analog Converter (RAMDAC) that transforms the digital data from the graphics and video subsystems to analog data for the VGA monitor. The PCH's integrated 180 MHz RAMDAC supports resolutions up to 1920x2000 at 60 Hz. Three 8-bit DACs provide the R, G, and B signals to the monitor. 5.28.1.1.1 Sync Signals HSYNC and VSYNC signals are digital and conform to TTL signal levels at the connector. Since these levels cannot be generated internal to the device, external level shifting buffers are required. These signals can be polarity adjusted and individually disabled in one of the two possible states. The sync signals should power up disabled in the high state. No composite sync or special flat panel sync support are included. 5.28.1.1.2 VESA*/VGA Mode VESA/VGA mode provides compatibility for pre-existing software that set the display mode using the VGA CRTC registers. Timings are generated based on the VGA register values and the timing generator registers are not used. 5.28.1.2 DDC (Display Data Channel) DDC is a standard defined by VESA. Its purpose is to allow communication between the host system and display. Both configuration and control information can be exchanged allowing plug- and-play systems to be realized. The PCH uses the DDC_CLK and DDC_DATA signals to communicate with the analog monitor. These signals are open drain and are 3.3 V tolerant. External pull-up resistors and level shifting circuitry should be implemented on the board. 5.28.2 Digital Display Side Band Signals The PCH integrates digital display side band signals AUX CH, DDC bus and Hot-Plug Detect signals even though digital display interfaces are moved to processor. There are three pairs of AUX CH, DDC Clock/Data and Hot-Plug Detect Signals on PCH that correspond to digital display interface/ports B, C and D. 250 Datasheet Functional Description 5.28.2.1 DisplayPort AUX CH Auxiliary Channel (AUX CH) is a half-duplex bidirectional channel used for link management and device control. AUX CH is a AC coupled differential signal. 5.28.2.2 DDC (Display Data Channel) DDC bus as mentioned in the Section 5.28.1.2 is used for communication between the host system and display. Three pairs of DDC (DDC_CLK and DDC_DATA) signals exist on the PCH which corresponds to three digital ports on the Processor. DDC follows I2C protocol. 5.28.2.3 Hot-Plug Detect The Hot-Plug Detect (HPD) signal serves as an interrupt request for the sink device for DisplayPort and HDMI. Its a 3.3 V tolerant signal pin on PCH. 5.28.2.4 Map of Digital Display Side Band Signals Per Display Configuration The table below lists PCH display side band signals associated with each digital port in the processor. Depending on whether a digital interface is configured as HDMI or DisplayPort on the processor, the corresponding signal on the PCH must be routed on the board as indicated by the table. Display Digital Interface 5.28.2.5 PCH Signals Digital Display Interface B Interface Configured as DisplayPort * DDPB_AUXP * DDPB_AUXN Interface Configured as HDMI * DDPB_CTRLCLK * DDPB_CTRLDATA Interface Configured as DisplayPort/HDMI * DDPB_HPD Digital Display Interface C Interface Configured as DisplayPort DDPC_AUXP DDPC_AUXN Interface Configured as HDMI DDPC_CTRLCLK DDPC_CTRLDATA Interface Configured as DisplayPort/HDMI DDPC_HPD Digital Display Interface D Interface Configured as DisplayPort DDPD_AUXP DDPD_AUXN Interface Configured as HDMI DDPD_CTRLCLK DDPD_CTRLDATA Interface Configured as DisplayPort/HDMI DDPD_HPD Panel Power Sequencing and Backlight Control PCH continues to integrate Panel power sequencing and Backlight control signals for the eDP interface on the processor. Datasheet 251 Functional Description This section provides details for the power sequence timing relationship of the panel power, the backlight enable and the eDP* data timing delivery. To meet the panel power timing specification requirements two signals, eDP_VDD_EN and eDP_BKLT_EN, are provided to control the timing sequencing function of the panel and the backlight power supplies. A defined power sequence is recommended when enabling the panel or disabling the panel. The set of timing parameters can vary from panel to panel vendor, provided that they stay within a predefined range of values. The panel VDD power, the backlight on/ off state and the eDP data lines are all managed by an internal power sequencer. Figure 5-18. Panel Power Sequencing T4 T1+T2 TX T5 T3 T4 Panel On Panel VDD Enable Panel BackLight Enable Off Clock/Data Lines Valid Off Power On Sequence from off state and Power Off Sequence after full On Note: 5.28.3 Support for programming parameters TX and T1 through T5 using software is provided. Intel(R) Flexible Display Interface (Intel(R) FDI) Intel FDI connects the display engine in the processor with the analog display interface/ port on the PCH. The display data from the frame buffer is processed in the display engine of the processor and sent to the PCH over the Intel FDI where it is transcoded as per the display protocol and driven through the DAC to the analog display monitor. The new generation PCH supports two Intel FDI lanes to send the data to Analog VGA interface. An Intel FDI channel consists of two lanes made up of differential signal pair. An Intel FDI lane supports data rate of 2.7 Gb/s. Intel(R) FDI continues to support lane reversal and polarity inversion. 252 Datasheet Functional Description 5.29 Intel(R) Virtualization Technology (Intel(R) VT) Intel Virtualization Technology (Intel VT) makes a single system appear as multiple independent systems to software. This allows for multiple, independent operating systems to be running simultaneously on a single system. Intel VT comprises technology components to support virtualization of platforms based on Intel architecture microprocessors and chipsets. The first revision of this technology (Intel VT-x) added hardware support in the processor to improve the virtualization performance and robustness. The second revision of this specification (Intel VT-d) adds chipset hardware implementation to improve I/O performance and robustness. The Intel VT-d specification and other VT documents can be referenced here: http:// www.intel.com/technology/platform-technology/virtualization/index.htm 5.29.1 Intel(R) Virtualization Technology (Intel(R) VT) for Directed I/O (Intel(R) VT-d) Objectives The key Intel VT-d objectives are domain based isolation and hardware based virtualization. A domain can be abstractly defined as an isolated environment in a platform to which a subset of host physical memory is allocated. Virtualization allows for the creation of one or more partitions on a single system. This could be multiple partitions in the same OS or there can be multiple operating system instances running on the same system offering benefits such as system consolidation, legacy migration, activity partitioning or security. 5.29.2 Intel(R) VT-d Features Supported * The following devices and functions support FLR in the PCH: -- High Definition Audio (Device 27: Function 0) -- SATA Host Controller 1 (Device 31: Function 2) -- SATA Host Controller 2 (Device 31: Function 5) -- USB2 (EHCI) Host Controller 1 (Device 29: Function 0) -- USB2 (EHCI) Host Controller 2 (Device 26: Function 0) -- GbE Lan Host Controller (Device 25: Function 0) * Interrupt virtualization support for IOxAPIC * Virtualization support for HPETs 5.29.3 Support for Function Level Reset (FLR) in PCH Intel VT-d allows system software (VMM/OS) to assign I/O devices to multiple domains. The system software, then, requires ways to reset I/O devices or their functions within, as it assigns/re-assigns I/O devices from one domain to another. The reset capability is required to ensure the devices have undergone proper re-initialization and are not keeping the stale state. A standard ability to reset I/O devices is also useful for the VMM in case where a guest domain with assigned devices has become unresponsive or has crashed. PCI Express defines a form of device hot reset which can be initiated through the Bridge Control register of the root/switch port to which the device is attached. However, the hot reset cannot be applied selectively to specific device functions. Also, no similar standard functionality exists for resetting root-complex integrated devices. Current reset limitations can be addressed through a function level reset (FLR) mechanism that allows software to independently reset specific device functions. Datasheet 253 Functional Description 5.29.4 Virtualization Support for PCH IOxAPIC The Intel VT-d architecture extension requires Interrupt Messages to go through the similar Address Remapping as any other memory requests. This is to allow domain isolation for interrupts such that a device assigned in one domain is not allowed to generate interrupts to another domain. The Address Remapping for Intel VT-d is based on the Bus:Device:Function field associated with the requests. Hence, it is required for the internal IOxAPIC to initiate the Interrupt Messages using a unique Bus:Device:Function. The PCH supports BIOS programmable unique Bus:Device:Function for the internal IOxAPIC. The Bus:Device:Function field does not change the IOxAPIC functionality in anyway, nor promoting IOxAPIC as a stand-alone device. The field is only used by the IOxAPIC in the following: * As the Requestor ID when initiating Interrupt Messages to the processor * As the Completer ID when responding to the reads targeting the IOxAPIC's Memory-Mapped I/O registers 5.29.5 Virtualization Support for High Precision Event Timer (HPET) The Intel VT-d architecture extension requires Interrupt Messages to go through the similar Address Remapping as any other memory requests. This is to allow domain isolation for interrupts such that a device assigned in one domain is not allowed to generate interrupts to another domain. The Address Remapping for Intel VT-d is based on the Bus:Device:Function field associated with the requests. Hence, it is required for the HPET to initiate the direct FSB Interrupt Messages using unique Bus:Device:Function. The PCH supports BIOS programmable unique Bus:Device:Function for each of the HPET timers. The Bus:Device:Function field does not change the HPET functionality in anyway, nor promoting it as a stand-alone device. The field is only used by the HPET timer in the following: * As the Requestor ID when initiating direct interrupt messages to the processor * As the Completer ID when responding to the reads targeting its Memory-Mapped registers * The registers for the programmable Bus:Device:Function for HPET timer 7:0 reside under the D31:F0 LPC Bridge's configuration space. 254 Datasheet Ballout Definition 6 Ballout Definition This chapter contains the PCH Ballout information. 6.1 Desktop/Server PCH Ballout This section contains the Desktop/Server PCH ballout. Figure 6-1, Figure 6-2, Figure 6-3, and Figure 6-4 show the ballout from a top of the package quadrant view. Table 6-1 is the BGA ball list, sorted alphabetically by signal name. Note: Datasheet References to PWM[3:0], TACH[7:0], SST, NMI#, SMI# are for Server/Workstation SKUs only. Pin names PWM[3:0], TACH[7:0], SST, NMI#, SMI# are Reserved on Desktop SKUs. See Chapter 2 for further details. 255 Ballout Definition Figure 6-1. Desktop/Server PCH Ballout (Top View - Upper Left) dW dW ssZD ssZD dW dW s^^ ssZD ssZD d/Z& s^^ Wd Wd s Wd s^^ s^^ s^^ Wd s^^ s^^ s^^ Wd s^^ , Wd Wd s^^ : WZ < ssZD &/^zE Wd h^d Wd s^^ s^^ Wd h^d s^^ WZ W//Z& &/ZyE &/ZyW s^^ ><KhdD/ E d ><KhdD/ ><KhdWE W h s^^ ><KhdWE^ W W &/ZyE Z WZ s^^ WZ s^^ s^^ WZ WZ WZ s^^ dW WZ s^^ yd>Khd &/ZyW yd>/E s^^ /></Z& &//Z& dW ><KhdW/ ><KhdW/ E W s^^ s^^ /&&></^Z & dW ><Khd/dWy ><Khd/dWy WE WW s^^ dW dW s>< ><KhdW/ ><KhdW/ W E s^^ dW dW ><KhdWW s^^ s ><KhdWE^ E t z ><KhdW/ W s^^ Figure 6-2. s^^ s ><KhdW/ ><KhdW/ W E s^^ s^^ ><KhdW/ ><KhdW/ W E s^^ s^^ s^^ s^^ s^^ s'>h s^^ ><KhdW/ ><KhdW/ E W s^^ ><KhdW/ ><KhdW/ W E s/K ><KhdW' ><KhdW' E W s^^ ><KhdW/ ><KhdW/ E W s^^ s' & ' , : s''ZE s s s^^ s^^ s^^ s's^zE s^^ /Z& s'/ZdE s',^zE W,W W,W WhyW D s'>< s'd WdZ>d WsE W<>dd> WhyW h^d h^d h^d h^d D/ZKDW D/dyW D/dyW h^d s^^ s^^ s^^ D/dyE s^^ s^^ WZ h^Z ></E'EW s^^ h^Z WZ h^Z ></E'EE h^Z h^Z s^^ s^^ h^Z s^^ WZ h^Z dW h^Z h^Z WZ h^Z dW h^Z h^Z s/K s^^ s^^ s^^ s/K s/K s/K W^h^ s^h^ ssZD s>< s^^ s/K s/K s>< s>< s s s s>< s>< s s s^^ s^^ d s^^ W<>dE s^^ ><KhdD, s^^ s s^^ s^^ s>< s>< s^^ s>< s>< WhyE s^^ s>< s^^ s s s^^ s s s s s^^ s s^t s^t s^t D/dyE s^^ s^^ s^^ s/K s/K s>< s^^ s^^ s^h^ h^ h^ s^h^ dW h^ h^ s^h^ WhyW s^^ s>< s^^ s>< ></EKd W s^^ h s^^ dW s>< ><KhdD, s>< s>< ></EKd E s^^ Z&></E s>< s^^ s^^ ><Khd&>y 'W/K ><Khd&>y 'W/K ><KhdD, ><KhdD, ><Khd&>y ><Khd&>y 'W/K 'W/K s^^ s^^ s^^ s^^ s^^ h^ h^ h^ h^ h^ h^ h^ h^ s^^ ><KhdD, s^h^ s^^ s^^ s>< t h^d D//Z& W,W s^^ Z 256 s^^ WdZ> WdZ>>< WdZ>>< d E W WhyE WhyE WdZ>>< WdZ>d < > s^^ Desktop/Server PCH Ballout (Top View - Lower Left) s>< s'Z ><KhdW/ E ><KhdW' ><KhdW' W E s^^ h^d W/ZKDW s^^ D E h^d WZ dW &//Ed Wd h^d Wd h^d s^^ &/ZKDW > WZ s^^ WZ s^^ Wd Wd s^^ Wd WZ s^^ s^^ & ' Wd s^^ h^ s>< s^^ h^ h^ s^^ h^ h^ s^^ h^ h^ s^^ h^ h^ s^^ h^ h^ h^ s^^ h^ s^^ s^^ h^ h^ h^Z/^ h^ s^^ h^Z/^ s^^ s Datasheet Ballout Definition Figure 6-3. Desktop/Server PCH Ballout (Top View - Upper Right) D/dyE D/dyW D/dyW ^dZyE WZ D/dyE s^^ ^dZyW WZ s^^ ^dZyW WZ s^^ ^dZyE s^^ ^dZyW ^dZyW s^^ s^^ ></ED/W s^^ D/ZyE ^ddyW Wd ></ED/E D/ZyE D/ZyW ^ddyE Wd s^^ D/ZyW s^^ s^^ ^dZyE ^dZyE WZ s^^ s^^ ^dZyW s^^ ^dZyE ^dZyE s^^ ^dZyW s^^ ^d/Z& s^^ s^^ ^ddyE ^ddyE ssZD ^ddyW ^dZKDW s^^ s^^ ^ddyW ^ddyW s^^ s^^ ></E^dE ></E^dW D/ZyE ^ddyW Wd dW D/ZyE D/ZyW ^ddyE Wd s^^ s^^ s^^ s^^ s^^ ^d'W 'W/K s^^ s/K s/K s^^ s^^ s/K s^^ dW 'W/K dW s^^ sWZK/K d,ZDdZ/W s^^ WZKWtZ' s^^ WD^zE, W>dZ^dWZK 'W/K s^^ s s s^^ s^^ s^^ s s s^t s^^ ^Z/ZY W/ ^d> ^d'W 'W/K ^d'W 'W/K s^t s^t s^t s^^ s^t s^t s^t s^t s^^ s^t s^t s^t s^^ s^^ s/K s/K s^t s s^^ ^z^Z^d ^>K< 'W/K ^dKhd 'W/K ^d'W 'W/K 'W/K ^dKhd 'W/K ^W<Z s^^ ^W/^ ^W/D/^K s s^^ s^^ >Z^d >d >>< ^W//K s ^z^WtZK< W/><ZY 'W/K ^h^>< 'W/K dW W/><ZY 'W/K ^W/^ s^h^ dW 'W/K W^^d W^h^ > 'W/K s^^ >ZY s^^ >ZY 'W/K d, 'W/K s^^ s^^ s^^ WD WtZK< s^^ ^>W^ 'W/K W/><ZY 'W/K s^^ s^^ 'W/K s^^ dW 'W/K > > s^^ sh^W>> >&ZD > d, 'W/K s^^ ,^/ ,Z^d Datasheet W/ZY, 'W/K K<E 'W/K ,^zE W/ZY s^h^, s^^ W/ZY ,^/ E s^W/ Z W ^W/>< ^W//K :d'd/ :d'dD^ s^^ :d'd< h 'W/K s t s^^ s^^ ^D>>< 'W/K ^D>d Z/ ^D>Zd 'W/K ^Dd s^^ ^D>>Zd 'W/K 'W/K z K'W/K K'W/K s^^ & K'W/K K'W/K ^h^tZE K'W/K ^h^WtZE< 'W/K s^^ K'W/K K'W/K ZDWtZK< ^D>< ' , ^^d t< ^D>>< 'W/K dW WZ^Ed 'W/K s^h^ s^^ s^h^ WtD d, 'W/K W/ZY&'W/K d,'W/K s^^ d, 'W/K s^^ d,'W/K 'W/K ^>W^ 'W/K 'W/K : 'W/K ^>W^ WtZdE < ^tsZDE D ^>Wt>E >EW,zWtZ 'W/K dZ>'W/K s^^ Z^DZ^d Zdy > E Zdy W s^h^ s^^ s^^ ^>W^h^ ^>W sZd 'W/K WtD s^^ s^^ WtD s^^ ^D>>Zd W,,Kd 'W/K ^h^< ^D>d 'W/K W/ZY s^^ K'W/K W/ZY W/ZY' 'W/K W/><ZY W/><ZY 'W/K 'W/K W>dZ^d ^h^^dd 'W/K W/ZY'W/K ^d'W 'W/K d,'W/K ,K<Z^ d'W/K ,>< > D ^W/DK^/ ^W/^ s^^ W/><ZY W/><ZY 'W/K 'W/K WtD ,^/ s^^ d s^^ s^^ , : 'W/KED/ ^d'W 'W/K s^^ W/><ZY 'W/K^D/ W^h^ ,^K ^>K 'W/K Desktop/Server PCH Ballout (Top View - Lower Right) s^^ ,^/ & ' < :d'dK ></ED,> KKW< s^^ s^^ s Figure 6-4. Z/E s/K s^^ s^^ s^^ D/ZyW s/K ssZD s^^ dW s^^ s^^ Dh^z 'W/K s^^ s^^ s^^ s^^ dW ssZD s^^ ^ddyE ^ddyW ssZD s^^ s^^ ^ddyE ssZD s^^ s^^ d, 'W/K /EdsZDE ^ZdZ^d /EdZhZ Z WtZK< s^^ d s^^ W^h^zW W^h^zW h s^^ s^^ ^>W>E WZd ZdZ^d WtZK< s^t s^^ s^t s^t s^^ s t 257 Ballout Definition Table 6-1. Desktop/ Server PCH Ballout By Signal Name (Sheet 1 of 17) EDS Net Name REV 0.7 EDS Net Name REV 0.7 Pin # Table 6-1. Desktop/ Server PCH Ballout By Signal Name (Sheet 3 of 17) EDS Net Name REV 0.7 Pin # ACPRESENT / GPIO31 AM36 CLKOUT_PEG_A_N AA3 DMI_TXN0 C20 APWROK AA32 CLKOUT_PEG_A_P AA2 DMI_TXN1 D21 BMBUSY# / GPIO0 G38 CLKOUT_PEG_B_N AE6 DMI_TXN2 B22 CL_CLK U36 CLKOUT_PEG_B_P AE7 DMI_TXN3 A24 CL_DATA U35 DMI_TXP0 B20 U34 CLKOUTFLEX0 / GPIO64 AV8 CL_RST# AM22 CLKOUTFLEX1 / GPIO65 AT9 G22 CLKOUTFLEX2 / GPIO66 AV9 CLKIN_33MHZLOOPBA CK CLKIN_DMI_N CLKIN_DMI_P F22 CLKIN_DOT96_N AP11 CLKOUTFLEX3 / GPIO67 AU8 CLKIN_DOT96_P AM11 DAC_IREF AF5 DMI_TXP1 B21 DMI_TXP2 C22 DMI_TXP3 B24 HDA_DOCK_EN# / GPIO33 AV26 DPWROK AV38 DRAMPWROK AE38 AM41 G16 DCPRTC AW35 DSWVRMEN CLKIN_GND_P F16 DCPSST AH28 eDP_BKLTCTL CLKIN_SATA_N H35 DCPSUS1 AE30 eDP_BKLTEN AT2 CLKIN_SATA_P H36 DCPSUS2 AJ22 eDP_VDDEN AP1 CLKOUT_33MHZ0 AV5 DCPSUS3 P19 FDI_CSYNC L2 CLKOUT_33MHZ1 AV7 DCPSUSBYP AU40 FDI_INT L3 CLKOUT_33MHZ2 AU2 DCPSUSBYP AU41 FDI_IREF N11 CLKOUT_33MHZ3 AN9 DDPB_AUXN AK6 FDI_RCOMP K2 CLKOUT_33MHZ4 AU5 DDPB_AUXP AK8 FDI_RXN0 N1 CLKIN_GND_N 258 Pin # Table 6-1. Desktop/ Server PCH Ballout By Signal Name (Sheet 2 of 17) AP2 CLKOUT_DMI_N R2 DDPB_CTRLCLK AM1 FDI_RXN1 P2 CLKOUT_DMI_P T2 DDPB_CTRLDATA AJ5 FDI_RXP0 N2 CLKOUT_DP_N T3 DDPB_HPD AJ2 FDI_RXP1 CLKOUT_DP_P T5 DDPC_AUXN AG7 GPIO15 CLKOUT_DPNS_N W2 DDPC_AUXP AG6 GPIO24 AE34 CLKOUT_DPNS_P U2 DDPC_CTRLCLK AN3 GPIO27 AU34 CLKOUT_ITPXDP_N U6 DDPC_CTRLDATA AM2 GPIO28 V41 CLKOUT_ITPXDP_P U7 DDPC_HPD AH5 GPIO32 N32 CLKOUT_PCIE_N0 AE10 DDPD_AUXN AG11 GPIO34 N34 CLKOUT_PCIE_N1 AC6 DDPD_AUXP AG10 GPIO35 / NMI# M40 CLKOUT_PCIE_N2 AC11 DDPD_CTRLCLK AN4 GPIO50 AH26 CLKOUT_PCIE_N3 W11 DDPD_CTRLDATA AN2 GPIO51 AU31 CLKOUT_PCIE_N4 Y4 DDPD_HPD AJ4 GPIO52 AJ26 CLKOUT_PCIE_N5 W7 DIFFCLK_BIASREF R11 GPIO53 AV31 CLKOUT_PCIE_N6 AA7 DMI_IREF A19 GPIO54 AW33 CLKOUT_PCIE_N7 R6 DMI_RCOMP B19 GPIO55 R30 CLKOUT_PCIE_P0 AE11 DMI_RXN0 L24 GPIO57 AC36 CLKOUT_PCIE_P1 AC7 DMI_RXN1 G24 GPIO72 AJ40 CLKOUT_PCIE_P2 AC10 DMI_RXN2 F26 GPIO8 AC40 CLKOUT_PCIE_P3 W10 DMI_RXN3 K26 HDA_BCLK AV23 CLKOUT_PCIE_P4 Y2 DMI_RXP0 K24 AN22 CLKOUT_PCIE_P5 W6 DMI_RXP1 H24 HDA_DOCK_RST# / GPIO13 CLKOUT_PCIE_P6 AA6 DMI_RXP2 G26 HDA_RST# AU24 CLKOUT_PCIE_P7 R7 DMI_RXP3 L26 HDA_SDI0 AT26 P3 AC32 Datasheet Ballout Definition Table 6-1. Desktop/ Server PCH Ballout By Signal Name (Sheet 4 of 17) EDS Net Name REV 0.7 Datasheet Pin # Table 6-1. Desktop/ Server PCH Ballout By Signal Name (Sheet 5 of 17) EDS Net Name REV 0.7 Pin # Table 6-1. Desktop/ Server PCH Ballout By Signal Name (Sheet 6 of 17) EDS Net Name REV 0.7 Pin # HDA_SDI1 AV22 PECI G40 PMSYNCH F40 HDA_SDI2 AT22 PERn1 / USB3Rn3 L14 PROCPWRGD D40 HDA_SDI3 AW23 PERn2 / USB3Rn4 F14 PWM0 AL31 HDA_SDO AU22 PERn3 F11 PWM1 AM31 HDA_SYNC AV24 PERn4 J11 PWM2 AP31 ICLK_IREF N10 PERn5 G9 PWM3 AV30 INTRUDER# AR41 PERn6 F7 PWRBTN# AK41 INTVRMEN AV36 PERn7 K6 PWROK AT40 JTAG_TCK Y40 PERn8 J2 RCIN# K36 JTAG_TDI W39 PERp1 / USB3Rp3 K14 REFCLK14IN AR7 JTAG_TDO Y38 PERp2 / USB3Rp4 G14 RI# AE36 JTAG_TMS W40 PERp3 H11 RSMRST# AM40 LAD0 AN24 PERp4 L11 RTCRST# AR38 LAD1 AP26 PERp5 F9 RTCX1 AN40 LAD2 AJ24 PERp6 H7 RTCX2 AN39 LAD3 AN26 PERp7 K8 SATA_IREF A33 LAN_PHY_PWR_CTRL / GPIO12 AL40 PERP8 J3 SATA_RCOMP D33 LDRQ0# AK22 LDRQ1# / GPIO23 AK26 LFRAME# AP24 OC0# / GPIO59 AE40 OC1# / GPIO40 AF37 OC2# / GPIO41 AD39 OC3# / GPIO42 AD40 OC4# / GPIO43 AF39 OC5# / GPIO9 AC41 OC6# / GPIO10 AF40 OC7# / GPIO14 AG40 PCIE_IREF B13 PCIE_RCOMP C13 PCIECLKRQ0# / GPIO73 W34 PCIECLKRQ1# / GPIO18 P39 PCIECLKRQ2# / GPIO20 / SMI# P37 PCIECLKRQ3# / GPIO25 AA39 PCIECLKRQ4# / GPIO26 W35 PCIECLKRQ5# / GPIO44 AA36 PCIECLKRQ6# / GPIO45 W32 PCIECLKRQ7# / GPIO46 AA40 PETn1 / USB3Tn3 B12 SATA_RXN0 B28 PETn2 / USB3Tn4 D11 SATA_RXN1 D30 PETn3 B9 SATA_RXN2 A31 PETn4 B8 SATA_RXN3 B32 PETn5 B7 SATA_RXN4 / PERn1 A26 PETn6 E1 SATA_RXN5 / PERn2 C27 PETn7 G3 SATA_RXP0 A28 PETn8 H2 SATA_RXP1 C30 PETp1 / USB3Tp3 B11 SATA_RXP2 B31 PETp2 / USB3Tp4 C11 SATA_RXP3 C32 PETp3 A9 SATA_RXP4 / PERp1 B26 PETp4 C8 SATA_RXP5 / PERp2 B27 PETp5 A7 SATA_TXN0 F31 PETp6 D2 SATA_TXN1 B34 PETp7 G5 SATA_TXN2 B35 PETp8 H1 SATA_TXN3 G33 PIRQA# AU29 SATA_TXN4 / PETn1 L28 PIRQB# AU27 SATA_TXN5 / PETn2 G28 PIRQC# AW28 SATA_TXP0 H31 PIRQD# AV27 SATA_TXP1 C34 PIRQE# / GPIO2 AR30 SATA_TXP2 D35 PIRQF# / GPIO3 AV29 SATA_TXP3 F33 PIRQG# / GPIO4 AV28 SATA_TXP4 / PETp1 K28 PIRQH# / GPIO5 AT27 SATA_TXP5 / PETp2 F28 PLTRST_PROC# F41 SATA0GP / GPIO21 M37 PLTRST# AA37 SATA1GP / GPIO19 J40 PME# AA31 SATA2GP / GPIO36 H40 259 Ballout Definition Table 6-1. Desktop/ Server PCH Ballout By Signal Name (Sheet 7 of 17) EDS Net Name REV 0.7 260 Table 6-1. Desktop/ Server PCH Ballout By Signal Name (Sheet 8 of 17) EDS Net Name REV 0.7 Pin # Pin # Table 6-1. Desktop/ Server PCH Ballout By Signal Name (Sheet 9 of 17) EDS Net Name REV 0.7 Pin # SATA3GP / GPIO37 N41 TACH0 / GPIO17 AP28 USB2n5 SATA4GP / GPIO16 M39 TACH1 / GPIO1 AT31 USB2n6 AU12 AV14 SATA5GP / GPIO49 N40 TACH2 / GPIO6 AM28 USB2n7 AU17 SATALED# J39 TACH3 / GPIO7 AV34 USB2n8 AW16 SCLOCK / GPIO22 L38 TACH4 / GPIO68 AT30 USB2n9 AN16 SDATAOUT0 / GPIO39 R31 TACH5 / GPIO69 AV35 USB2p0 AU10 SDATAOUT1 / GPIO48 L40 TACH6 / GPIO70 AK28 USB2p1 AW11 SERIRQ G39 TACH7 / GPIO71 AT34 USB2p10 AK18 SLOAD / GPIO38 H41 TD_IREF C3 USB2p11 AN18 C40 USB2p12 AV18 A2 USB2p13 AN20 SLP_A# AN37 THRMTRIP# SLP_LAN# AU36 TP1 SLP_S3# AK40 TP10 L5 USB2p2 AP14 SLP_S4# AT35 TP11 L16 USB2p3 AK16 SLP_S5# / GPIO63 AA35 TP12 L22 USB2p4 AV15 SLP_SUS# AK38 TP13 N12 USB2p5 AT12 SLP_WLAN# / GPIO29 AL39 TP14 N30 USB2p6 AW14 SMBALERT# / GPIO11 AG31 TP15 P5 USB2p7 AT17 SMBCLK AG36 TP16 R4 USB2p8 AV16 SMBDATA AG32 TP17 R12 USB2p9 AP16 SML0ALERT# / GPIO60 AG35 TP18 U10 USB3Rn1 F20 SML0CLK AE32 TP19 U11 USB3Rn2 G18 SML0DATA AE35 TP2 A3 USB3Rn5 K20 SML1ALERT# / TEMP_ALERT#/ GPIO74 AJ39 TP20 W37 USB3Rn6 L18 TP21 AC35 USB3Rp1 G20 SML1CLK / GPIO58 AK36 TP22 AH24 USB3Rp2 H18 SML1DATA / GPIO75 AK33 TP23 AJ14 USB3Rp5 L20 TP24 AK14 USB3Rp6 K18 TP25 B18 SPI_CLK U39 SPI_CS0# R38 SPI_CS1# R35 SPI_CS2# R40 SPI_IO2 U40 SPI_IO3 U37 SPI_MISO R36 SPI_MOSI P40 SPKR R32 SRTCRST# AR39 SST AJ31 SUS_STAT# / GPIO61 AD37 SUSACK# AJ37 SUSCLK / GPIO62 W36 SUSWARN# / SUSPWRDNACK / GPIO30 AG41 SYS_PWROK W31 SYS_RESET# N36 AM34 USB3Tn1 TP3 B1 USB3Tn2 B15 TP4 B2 USB3Tn5 D15 TP5 K5 USB3Tn6 B14 TP6 K16 USB3Tp1 C18 TP7 K22 USB3Tp2 B16 TP8 K33 USB3Tp5 C15 K34 USB3Tp6 TP9 A14 USB2n0 AV10 USBRBIAS AU20 USB2n1 AV11 USBRBIAS# AV20 USB2n10 AJ18 V_PROC_IO C39 USB2n11 AP18 VCC V17 USB2n12 AW18 VCC V19 USB2n13 AP20 VCC V20 USB2n2 AN14 VCC V22 USB2n3 AJ16 VCC V23 USB2n4 AU15 VCC V25 Datasheet Ballout Definition Table 6-1. Desktop/ Server PCH Ballout By Signal Name (Sheet 10 of 17) EDS Net Name REV 0.7 EDS Net Name REV 0.7 Pin # Table 6-1. Desktop/ Server PCH Ballout By Signal Name (Sheet 12 of 17) EDS Net Name REV 0.7 Pin # VCC W17 VCCCLK3_3 AK11 VCCVRM A4 VCC W19 VCCCLK3_3 AM7 VCCVRM A38 VCC W23 VCCCLK3_3 AM9 VCCVRM A39 VCC W25 VCCCLK3_3 AP5 VCCVRM A40 VCC AA19 VCCCLK3_3 AP7 VCCVRM B4 VCC AA20 VCCCLK3_3 AR4 VCCVRM B37 VCC AB1 VCCCLK3_3 AT5 VCCVRM B39 VCC AB16 VCCCLK3_3 AV3 VCCVRM C1 VCC AB17 VCCCLK3_3 AV4 VCCVRM C2 VCC AB19 VCCCLK3_3 AW3 VCCVRM K1 VCC AB20 VCCCLK3_3 AW4 VCCVRM T14 VCC AD16 VCCCLK3_3 AW9 VGA_BLUE AC3 VCC3_3 B6 VCCDSW3_3 AV39 VGA_DDC_CLK AL2 VCC3_3 U30 VCCDSW3_3 AW38 VGA_DDC_DATA AL3 VCC3_3 W30 VCCDSW3_3 AW39 VGA_GREEN AE2 VCC3_3 AF26 VCCIO M14 VGA_HSYNC AH3 VCC3_3 AG1 VCCIO P14 VGA_IRTN AG4 VCC3_3 AW21 VCCIO P16 VGA_RED AC2 AF2 VCCIO P17 VGA_VSYNC AH2 VCCADACBG3_3 AE1 VCCIO P22 VSS A12 VCCASW W26 VCCIO P23 VSS A16 VCCASW AA23 VCCIO P25 VSS A21 VCCASW AA25 VCCIO P26 VSS A35 VCCASW AA26 VCCIO P28 VSS B3 VCCASW AB22 VCCIO T19 VSS B25 VCCASW AB23 VCCIO T20 VSS B30 VCCASW AB25 VCCIO AC12 VSS B33 VCCASW AB26 VCCIO AF19 VSS B38 VCCASW AD17 VCCIO AF20 VSS B40 VCCASW AD19 VCCIO AF22 VSS B41 VCCASW AD20 VCCIO AF23 VSS C6 VCCASW AD22 VCCRTC AP33 VSS C25 VCCASW AD23 VCCSPI R41 VSS C37 VCCASW AD25 VCCSUS3_3 P20 VSS C41 VCCASW AF25 VCCSUS3_3 AH18 VSS D1 VCCCLK T16 VCCSUS3_3 AH20 VSS D4 VCCCLK U12 VCCSUS3_3 AH22 VSS D6 VCCCLK V14 VCCSUS3_3 AJ20 VSS D7 VCCCLK V16 VCCSUS3_3 AK20 VSS D8 VCCCLK W14 VCCSUS3_3 AM33 VSS D9 VCCCLK W16 VCCSUS3_3 AN33 VSS D12 VCCCLK AA16 VCCSUS3_3 AP35 VSS D13 VCCCLK AB2 VCCSUSHDA AW26 VSS D14 AG12 VCCUSBPLL AP22 VSS D16 VCCADAC1_5 VCCCLK3_3 Datasheet Pin # Table 6-1. Desktop/ Server PCH Ballout By Signal Name (Sheet 11 of 17) 261 Ballout Definition Table 6-1. Desktop/ Server PCH Ballout By Signal Name (Sheet 13 of 17) EDS Net Name REV 0.7 262 Pin # Table 6-1. Desktop/ Server PCH Ballout By Signal Name (Sheet 14 of 17) EDS Net Name REV 0.7 Pin # Table 6-1. Desktop/ Server PCH Ballout By Signal Name (Sheet 15 of 17) EDS Net Name REV 0.7 Pin # VSS D18 VSS K4 VSS Y41 VSS D19 VSS K9 VSS AA5 VSS D20 VSS K31 VSS AA8 VSS D22 VSS L37 VSS AA10 VSS D24 VSS L41 VSS AA11 VSS D25 VSS M16 VSS AA12 VSS D26 VSS M18 VSS AA14 VSS D27 VSS M20 VSS AA17 VSS D28 VSS M22 VSS AA22 VSS D31 VSS M24 VSS AA28 VSS D32 VSS M26 VSS AA30 VSS D34 VSS M28 VSS AA34 VSS D37 VSS N4 VSS AB4 VSS D41 VSS N8 VSS AB14 VSS E3 VSS N31 VSS AB28 VSS E4 VSS N35 VSS AC5 VSS E5 VSS N38 VSS AC8 VSS E7 VSS R1 VSS AC30 VSS E12 VSS R8 VSS AC31 VSS E31 VSS R10 VSS AC34 VSS E35 VSS R34 VSS AC38 VSS E38 VSS T17 VSS AD14 VSS F18 VSS T22 VSS AD26 VSS F24 VSS T23 VSS AD28 VSS F35 VSS T25 VSS AE4 VSS F37 VSS T26 VSS AE8 VSS F38 VSS T28 VSS AE12 VSS G2 VSS U1 VSS AE31 VSS H4 VSS U4 VSS AE41 VSS H6 VSS U8 VSS AF3 VSS H8 VSS U31 VSS AF14 VSS H9 VSS U32 VSS AF16 VSS H14 VSS V26 VSS AF17 VSS H16 VSS V28 VSS AF28 VSS H20 VSS V38 VSS AG2 VSS H22 VSS V40 VSS AG8 VSS H26 VSS W3 VSS AG30 VSS H28 VSS W5 VSS AG34 VSS H33 VSS W8 VSS AG38 VSS H34 VSS W12 VSS AH14 VSS H38 VSS W20 VSS AH16 VSS J5 VSS W22 VSS AJ1 VSS J31 VSS W28 VSS AJ28 VSS J37 VSS Y1 VSS AK9 Datasheet Ballout Definition Table 6-1. Desktop/ Server PCH Ballout By Signal Name (Sheet 16 of 17) EDS Net Name REV 0.7 Datasheet Pin # Table 6-1. Desktop/ Server PCH Ballout By Signal Name (Sheet 17 of 17) EDS Net Name REV 0.7 Pin # VSS AK24 VSS VSS AK37 VSS AV2 VSS AL5 VSS AV12 VSS AL11 VSS AV17 VSS AL37 VSS AV21 VSS AM4 VSS AV33 VSS AM6 VSS AV40 VSS AM8 VSS AV41 VSS AM14 VSS AW2 VSS AM16 VSS AW7 VSS AM18 VSS AW30 VSS AM20 VSS AW40 VSS AM24 WAKE# AK34 VSS AM26 XTAL25_IN N7 VSS AM35 XTAL25_OUT N6 VSS AM38 VSS AN28 VSS AP4 VSS AP9 VSS AR11 VSS AR35 VSS AR37 VSS AT1 VSS AT7 VSS AT8 VSS AT10 VSS AT11 VSS AT14 VSS AT15 VSS AT16 VSS AT18 VSS AT20 VSS AT21 VSS AT23 VSS AT24 VSS AT28 VSS AT29 VSS AT33 VSS AT36 VSS AT38 VSS AT41 VSS AU1 VSS AU3 VSS AU39 AV1 263 Ballout Definition 6.2 Mobile PCH Ballout This section contains the PCH ballout. Figure 6-5, Figure 6-6, Figure 6-7 and Figure 6-8 show the ballout from a top of the package quadrant view. Table 6-2 is the BGA ball list, sorted alphabetically by signal name. Figure 6-5. s^^ Mobile PCH Ballout (Top View - Upper Left) s^^ s^^ s^^ sZd s^^ Zdy Zdy s^^ s^^ & ^>W^h^ ' K'W/K W/><ZY 'W/K d, 'W/K d, 'W/K > K<E 'W/K s^^ d, 'W/K > s^^ > >&ZD s^^ ,K<Z^ d'W/K > ></ED,> KKW< ,^zE >ZY s^^ ^D>>< 'W/K d>Kt 'W/K dW WtZK< d,'W/K s^^ W/ZY&'W/K s^^ ,^/ s^^ /EdsZDE d, 'W/K d,'W/K W/ZY'W/K >ZY 'W/K ,^/ s^^ s^^ d, 'W/K s^^ W/ZY s^^ s^^ >EW,zWtZ dZ>'W/K s^^ W/ZY s^^ ,^/ WtZK< W/ZY' 'W/K s^t W/ZY ,^/ W/ZY, 'W/K s^^ W/ZY s^^ s^h^ ^D>Zd ^D>>Zd 'W/K 'W/K s^^ ^D>d 'W/K s^^ WZd WZd s s s^^ ^h^< ^D>d s^^ ^D>< 'W/K s^^ s^^ s^^ s^t s^h^ s^h^ s^^ ^h^^dd 'W/K ^D>>< s^^ ^Dd 'W/K W^h^zW s^^ s^t s^t s^t s^^ s^^ s^t s^t s^t s^^ s^^ s^t s^t s^t W^^d s^^ s^t s^^ s^^ ^h^>< 'W/K ^>W^ 'W/K s^^ 'W/K W>dZ^d W^h^ s^^ dW :d'd< WtZK< s^^ dW 'W/K s^^ Mobile PCH Ballout (Top View - Lower Left) s^^ :d'dD^ :d'dK W/><ZY 'W/K s^^ ^z^WtZK< s^^ WD 'W/K s^W/ W/><ZY 'W/K :d'd/ W/><ZY 'W/K^D/ W'><ZY 'W/K >Z^d s^^ >d >>< ^W/DK^/ ^W//K ^W//K s^^ ^W/^ s^^ ^W/^ ^W/>< sWZK/K ^d'W 'W/K s^^ 'W/K ^W/^ s^^ ^W<Z ^Z/ZY ^d'W 'W/K 'W/KED/ ^dKhd 'W/K 'W/K ><ZhE s^^ dW ssZD ^d> s^^ ^d'W 'W/K ^d'W 'W/K ^d'W 'W/K d,ZDdZ/W W/ s^^ WZKWtZ' s^^ s^^ s s s s s^^ s s s Z/E ^>K 'W/K s^^ s^^ Dh^z 'W/K sWZK/K s^^ s^^ s^^ s^^ s^^ s^^ s/K s/K s/K s^^ s^^ s/K s/K s/K s^^ s^^ ^ddyE Wd D/ZyE D/ZyW s/K ^ddyE ^ddyW Wd D/ZyW D/ZyE s/K ^ddyW s^^ s^^ s^^ s/K WD^zE, ^dZKDW s^^ ^ddyE s^^ ^ddyE Wd dW D/ZyE s^^ ^ddyE ^ddyW ^ddyW ^ddyW Wd dW D/ZyW D/ZyE ^ddyW s^^ ^ddyE s^^ D/ZKDW s^^ D/ZyW dW ^>K< 'W/K dW s s W>dZ^dWZK s^^ z s^^ s^^ s^^ ^dKhd 'W/K ^z^Z^d s^^ ^W/D/^K ^d'W 'W/K t s^^ s s s^^ h 264 W'><ZY 'W/K W/><ZY 'W/K Z s ^D>>Zd W,,Kd 'W/K s^^ W/><ZY 'W/K 'W/K E d s^t s^^ > W 'W/K 'W/K W/><ZY 'W/K K'W/K : D W/><ZY 'W/K K'W/K ' < s^^ 'W/K d,'W/K K'W/K K'W/K , Z/ s^^ & K'W/K Figure 6-6. ^h^tZE ^h^WtZE< 'W/K K'W/K ^>W>E t< K'W/K t z ^ZdZ^d 'W/K s^^ h s ZdZ^d ZDWtZK< WtZdE Z d 'W/K ^tsZDE ^>W Z^DZ^d E W WZ^Ed 'W/K ^>W^ > D s^^ s^^ s^^ : < ^>Wt>E 'W/K /EdZhZ ^>W^ , s^^ ^d/Z& s^^ s^^ ^dZyW WZ ^dZyE ></E^dW ^dZyE s^^ s^^ ></E^dE ^dZyE ^dZyW ^dZyW ^dZyE WZ s^^ ^dZyW s^^ s^^ ^dZyW WZ ^dZyW D/dyW ^dZyE WZ ^dZyE D/dyE D//Z& D/dyW D/dyW D/dyW s^^ D/dyE s^^ D/dyE D/dyE h^d ssZD Datasheet Ballout Definition Figure 6-7. ,^K Mobile PCH Ballout (Top View - Upper Right) s^h^, ,>< ,Z^d h^ s^^ dW h^ h^ s^^ h^ h^ s^^ h^ h^ h^ h^ h^ h^ s^^ h^ h^ h^ h^ h^ ><KhdD, s^^ s^^ s^^ ><KhdD, s^^ s^^ ><Khd&>y 'W/K h^ ><KhdD, s^^ ><KhdD, h^ s^^ h^ s^^ ><Khd&>y 'W/K h^ h^ h^ h^ ></EKd W WsE s^^ s^^ h^ s^^ ></EKd E s^^ ><KhdD, ><Khd&>y ><Khd&>y 'W/K 'W/K s^^ s^^ s^^ h^Z/^ s^^ h^ s^^ W<>dE W,W s s>< s>< h^ dW s^^ s>< s>< s' dW s^^ s^^ s^^ s^^ s^^ s^h^ s^h^ s^h^ s s s^^ WdZ>>< WdZ> d s^^ s^t s^h^ s^^ s/K s>< s^^ sh^W>> s/K s^^ s^t s^^ s/K s/K s>< s^^ Z&></E WhyW WhyE s^^ W,W s^^ WdZ> d W<>dd> s^^ WdZ>>< s',^zE WdZ> WdZ>>< d WhyW < s'd D : > E s /Z& s^^ s'>h s'Z s s s^^ s s/K s^^ s>< s>< s^^ ><KhdW' ><KhdW' W E s^^ ><KhdW/ E s^^ ><KhdW/ W s>< s^^ Figure 6-8. W^h^ ><KhdW' ><KhdW' E W s^^ ><KhdW/ ><KhdW/ W E ><KhdW/ W ><KhdW/ E ><KhdW/ E ><KhdW/ W ><KhdW/ W s^^ s s s^^ s^^ s s s^^ s>< s>< s>< s>< s>< dW dW ><KhdW/ E s^^ ><KhdW/ W ssZD s s^^ s^^ s>< s>< s^^ W^h^ W^h^ s^h^ s^h^ s^^ ssZD ssZD s s s^^ s^^ s^^ s^^ s^^ s^^ h^Z h^Z s^^ ></E'EE h^Z h^Z WZ h^Z WZ ></E'EW s^^ s^^ WZ h^Z WZ ><KhdWE^ ><KhdWE^ E W s^^ ><KhdD/ ><KhdD/ E W ><KhdW/ E ><KhdW/ E s^^ &/ZyE &/ZyW s^^ ><KhdW/ W ><KhdWW ><KhdWE &/ZyE &/ZyW s^^ &/^zE &//Ed s/K s^^ WZ WZ s^^ s^^ s^^ s^^ s^^ h^Z h^Z s^^ s^^ WZ h^Z h^Z WZ h^Z WZ WZ WZ ></ED/E s^^ s^^ WZ h^Z WZ s^^ WZ h^d h^d h^d Datasheet Wd h^d W/ZKDW h^d Wd h^d dW WZ WZ s^^ Wd h^d W//Z& s^^ Wd s^^ Wd D > E &//Z& dW Wd Wd s^^ Wd dW s^^ Wd Wd Wd s^^ Wd s^^ dW dW s t dW z dW ssZD Wd d h dW d/Z& W Z dW ssZD Wd Wd Wd h^d s^^ /></Z& : s s^^ dW < &/ZKDW ></ED/W s^^ s^^ /&&></^Z & s^^ dW h^d , yd>Khd yd>/E s/K ><Khd/dWy WW ><KhdW/ E s^^ & ' s^^ s^^ s^^ ><KhdW/ W ><Khd/dWy WE h^d z Mobile PCH Ballout (Top View - Lower Right) s h^d s t s^^ s^^ d h s''ZE s^^ W Z s^^ s^^ s'/ZdE & , s's^zE s^^ WhyE s^^ s'>< ' WhyW WhyE s^^ W,W h^Z/^ s^^ s^^ h^ h^ dW s^^ 265 Ballout Definition Table 6-2. Mobile PCH Ballout by Signal Name (Sheet 1 of 16) EDS Net Name Rev 0.7 Datasheet Pin # Table 6-2. Mobile PCH Ballout by Signal Name (Sheet 2 of 16) EDS Net Name Rev 0.7 Table 6-2. Mobile PCH Ballout by Signal Name (Sheet 3 of 16) Pin # EDS Net Name Rev 0.7 Pin # ACPRESENT / GPIO31 E6 CLKOUT_PCIE_P7 AJ42 DMI_RXP1 AP20 APWROK AB7 CLKOUT_PEG_A_N AB35 DMI_RXP2 AR17 BATLOW# / GPIO72 K7 CLKOUT_PEG_A_P AB36 DMI_RXP3 AW20 BMBUSY# / GPIO0 AT8 CLKOUT_PEG_B_N Y39 DMI_TXN0 BD21 CL_CLK AF11 CLKOUT_PEG_B_P Y38 DMI_TXN1 BE20 CL_DATA AF10 CLKOUTFLEX0 / GPIO64 C40 DMI_TXN2 BD17 CL_RST# AF7 CLKIN_33MHZLOOPB ACK D17 CLKOUTFLEX1 / GPIO65 F38 CLKIN_DMI_N AY24 F36 CLKIN_DMI_P AW24 CLKOUTFLEX2 / GPIO66 DMI_TXN3 BE18 DMI_TXP0 BB21 DMI_TXP1 BC20 DMI_TXP2 BB17 F39 DMI_TXP3 BC18 HAD_DOCK_EN# / GPIO33 B17 CLKIN_DOT96_N H33 CLKOUTFLEX3 / GPIO67 CLKIN_DOT96_P G33 CLKRUN# AN7 CLKIN_GND_N AR24 DAC_IREF U40 DPWROK L13 CLKIN_GND_P AT24 DCPRTC P14 DRAMPWROK H3 CLKIN_SATA_N BE6 DCPRTC P16 DSWVRMEN C8 CLKIN_SATA_P BC6 DCPSST AA14 eDP_BKLTCTL N36 CLKOUT_33MHZ0 D44 DCPSUS1 Y12 eDP_BKLTEN K36 CLKOUT_33MHZ1 E44 DCPSUS2 Y35 eDP_VDDEN G36 CLKOUT_33MHZ2 B42 DCPSUS3 AJ26 FDI_CSYNC AL39 CLKOUT_33MHZ3 F41 DCPSUS3 AJ28 FDI_INT AL40 CLKOUT_33MHZ4 A40 DCPSUSBYP U14 FDI_IREF AT45 CLKOUT_DMI_N AF39 DDPB_AUXN H45 FDI_RCOMP AR44 CLKOUT_DMI_P AF40 DDPB_AUXP H43 FDI_RXN0 AJ35 CLKOUT_DP_N AJ40 DDPB_CTRLCLK R40 FDI_RXN1 AL35 CLKOUT_DP_P AJ39 DDPB_CTRLDATA R39 FDI_RXP0 AJ36 CLKOUT_DPNS_N AF35 DDPB_HPD K40 FDI_RXP1 AL36 AB11 CLKOUT_DPNS_P AF36 DDPC_AUXN K43 GPIO15 CLKOUT_ITPXDP_N AH43 DDPC_AUXP K45 GPIO24 Y10 CLKOUT_ITPXDP_P AH45 DDPC_CTRLCLK R35 GPIO27 R11 CLKOUT_PCIE_N0 Y43 DDPC_CTRLDATA R36 GPIO28 AD11 CLKOUT_PCIE_N1 AA44 DDPC_HPD K38 GPIO34 AN6 CLKOUT_PCIE_N2 AB43 DDPD_AUXN J42 GPIO35 / NMI# AP1 CLKOUT_PCIE_N3 AD43 DDPD_AUXP J44 GPIO50 A12 C10 CLKOUT_PCIE_N4 AF43 DDPD_CTRLCLK N40 GPIO51 CLKOUT_PCIE_N5 AE44 DDPD_CTRLDATA N38 GPIO52 B13 CLKOUT_PCIE_N6 AB40 DDPD_HPD H39 GPIO53 A10 CLKOUT_PCIE_N7 AJ44 DIFFCLK_BIASREF AN44 GPIO54 C12 CLKOUT_PCIE_P0 Y45 DMI_IREF BE16 GPIO55 AL6 CLKOUT_PCIE_P1 AA42 DMI_RCOMP AY17 GPIO57 U12 CLKOUT_PCIE_P2 AB45 DMI_RXN0 AW22 GPIO8 Y1 CLKOUT_PCIE_P3 AD45 DMI_RXN1 AR20 HDA_BCLK B25 CLKOUT_PCIE_P4 AF45 DMI_RXN2 AP17 AE42 DMI_RXN3 AV20 HDA_DOCK_RST# / GPIO13 C22 CLKOUT_PCIE_P5 CLKOUT_PCIE_P6 AB39 DMI_RXP0 AY22 HDA_RST# C24 HDA_SDI0 L22 266 Ballout Definition Table 6-2. Mobile PCH Ballout by Signal Name (Sheet 4 of 16) EDS Net Name Rev 0.7 267 Pin # HDA_SDI1 K22 HDA_SDI2 G22 HDA_SDI3 F22 HDA_SDO A24 HDA_SYNC A22 ICLK_IREF AM45 INTRUDER# A8 INTVRMEN G10 JTAG_TCK AB3 JTAG_TDI AE2 JTAG_TDO AD3 JTAG_TMS AD1 LAD0 A20 LAD1 C20 LAD2 A18 LAD3 C18 LAN_PHY_PWR_CTRL / GPIO12 K13 LDRQ0# D21 LDRQ1# / GPIO23 G20 LFRAME# B21 OC0# / GPIO59 P3 OC1# / GPIO40 V1 OC2# / GPIO41 U2 OC3# / GPIO42 P1 OC4# / GPIO43 M3 OC5# / GPIO9 T1 OC6# / GPIO10 N2 OC7# / GPIO14 M1 PCIE_IREF BE30 PCIE_RCOMP BD29 PCIECLKRQ0# / GPIO73 AB1 PCIECLKRQ1# / GPIO18 AF1 PCIECLKRQ2# / GPIO20 / SMI# AF3 PCIECLKRQ3# / GPIO25 T3 PCIECLKRQ4# / GPIO26 V3 PCIECLKRQ5# / GPIO44 AA2 PCIECLKRQ6# / GPIO45 AE4 PCIECLKRQ7# / GPIO46 Y3 PECI AY1 Table 6-2. Mobile PCH Ballout by Signal Name (Sheet 5 of 16) EDS Net Name Rev 0.7 Pin # PEG_A_CLKRQ# / GPIO47 AF6 PEG_B_CLKRQ# / GPIO56 U4 PERn1 / USB3Rn3 AW31 PERn2 / USB3Rn4 AT31 PERn3 AW33 PERn4 AT33 PERn5 AW36 PERn6 AY38 PERn7 AT40 PERn8 AN38 PERp1 / USB3Rp3 AY31 PERp2 / USB3Rp4 AR31 PERp3 AY33 PERp4 AR33 PERp5 AV36 PERp6 AW38 PERp7 AT39 PERP8 AN39 PETn1 / USB3Tn3 BE32 PETn2 / USB3Tn4 BD33 PETn3 BE34 PETn4 BE36 PETn5 BD37 PETn6 BC38 PETn7 BE40 PETn8 BD42 PETp1 / USB3Tp3 BC32 PETp2 / USB3Tp4 BB33 PETp3 BC34 PETp4 BC36 PETp5 BB37 PETp6 BE38 PETp7 BC40 PETp8 BD41 PIRQA# H20 PIRQB# L20 PIRQC# K17 PIRQD# M20 PIRQE# / GPIO2 G17 PIRQF# / GPIO3 F17 PIRQG# / GPIO4 L15 PIRQH# / GPIO5 M15 PLTRST_PROC# AU4 PLTRST# Y11 Table 6-2. Mobile PCH Ballout by Signal Name (Sheet 6 of 16) EDS Net Name Rev 0.7 Pin # PME# AD10 PMSYNCH AY3 PROCPWRGD AV3 PWRBTN# K1 PWROK F10 RCIN# AT6 REFCLK14IN F45 RI# N4 RSMRST# J2 RTCRST# D9 RTCX1 B5 RTCX2 B4 SATA_IREF BD4 SATA_RCOMP AY5 SATA_RXN0 BC8 SATA_RXN1 BC10 SATA_RXN2 BB9 SATA_RXN3 BC12 SATA_RXN4 / PERn1 BD13 SATA_RXN5 / PERn2 BC14 SATA_RXP0 BE8 SATA_RXP1 BE10 SATA_RXP2 BD9 SATA_RXP3 BE12 SATA_RXP4 / PERp1 BB13 SATA_RXP5 / PERp2 BE14 SATA_TXN0 AW8 SATA_TXN1 AV10 SATA_TXN2 AY13 SATA_TXN3 AR13 SATA_TXN4 / PETn1 AV15 SATA_TXN5 / PETn2 AP15 SATA_TXP0 AY8 SATA_TXP1 AW10 SATA_TXP2 AW13 SATA_TXP3 AT13 SATA_TXP4 / PETp1 AW15 SATA_TXP5 / PETp2 AR15 SATA0GP / GPIO21 AT1 SATA1GP / GPIO19 AU2 SATA2GP / GPIO36 AT3 SATA3GP / GPIO37 AK1 SATA4GP / GPIO16 AN2 SATA5GP / GPIO49 AK3 SATALED# AP3 Datasheet Ballout Definition Table 6-2. Mobile PCH Ballout by Signal Name (Sheet 7 of 16) EDS Net Name Rev 0.7 Datasheet Table 6-2. Mobile PCH Ballout by Signal Name (Sheet 8 of 16) Table 6-2. Mobile PCH Ballout by Signal Name (Sheet 9 of 16) Pin # EDS Net Name Rev 0.7 SCLOCK / GPIO22 BB4 TACH5 / GPIO69 D13 USB2p1 C38 SDATAOUT0 / GPIO39 AM3 TACH6 / GPIO70 G13 USB2p10 D29 SDATAOUT1 / GPIO48 AN4 TACH7 / GPIO71 H15 USB2p11 C28 SERIRQ AL11 TD_IREF AY43 USB2p12 F26 SLOAD / GPIO38 AT7 THRMTRIP# AV1 USB2p13 G24 C36 Pin # EDS Net Name Rev 0.7 Pin # SLP_A# F3 TP1 BA45 USB2p2 SLP_LAN# G5 TP10 AW44 USB2p3 C34 SLP_S3# H1 TP11 BC30 USB2p4 D33 G31 SLP_S4# C6 TP12 AW17 USB2p5 SLP_S5# / GPIO63 Y7 TP13 AU44 USB2p6 L31 SLP_SUS# F1 TP14 AN10 USB2p7 H29 SLP_WLAN# / GPIO29 D2 TP15 AV45 USB2p8 C32 SMBALERT# / GPIO11 N7 TP16 AV43 USB2p9 C30 SMBCLK R10 TP17 AU42 USB3Rn1 AR26 SMBDATA U11 TP18 AD38 USB3Rn2 AW26 SML0ALERT# / GPIO60 N8 TP19 AD39 USB3Rn5 AW29 SML0CLK U8 TP2 BC45 USB3Rn6 AR29 SML0DATA R7 TP20 AB6 USB3Rp1 AP26 SML1ALERT# / TEMP_ALERT#/ GPIO74 H6 TP21 AB10 USB3Rp2 AV26 TP22 C26 USB3Rp5 AV29 TP23 L33 USB3Rp6 AP29 SML1CLK / GPIO58 K6 TP24 M33 USB3Tn1 BE24 SML1DATA / GPIO75 N11 TP25 F8 USB3Tn2 BD25 SPI_CLK AJ11 TP3 BE44 USB3Tn5 BE26 SPI_CS0# AJ7 TP4 BE43 USB3Tn6 BD27 SPI_CS1# AL7 TP5 AY45 USB3Tp1 BD23 SPI_CS2# AJ10 TP6 BB29 USB3Tp2 BC24 SPI_IO2 AJ4 TP7 AV17 USB3Tp5 BC26 SPI_IO3 AJ2 TP8 BB2 USB3Tp6 BE28 SPI_MISO AH3 TP9 BA2 USBRBIAS K26 SPI_MOSI AH1 USB2n0 B37 USBRBIAS# K24 SPKR AL10 USB2n1 A38 V_PROC_IO AJ12 SRTCRST# B9 USB2n10 B29 V_PROC_IO AJ14 SUS_STAT# / GPIO61 U7 USB2n11 A28 VCC P18 SUSACK# R6 USB2n12 G26 VCC P20 SUSCLK / GPIO62 Y6 USB2n13 F24 VCC Y26 SUSWARN# / SUSPWRNACK / GPIO30 J4 USB2n2 A36 VCC AA24 USB2n3 A34 VCC AA26 USB2n4 B33 VCC AD20 USB2n5 F31 VCC AD22 USB2n6 K31 VCC AD24 USB2n7 G29 VCC AD26 USB2n8 A32 VCC AD28 USB2n9 A30 VCC AE18 USB2p0 D37 VCC AE20 SYS_PWROK AD7 SYS_RESET# AM1 TACH0 / GPIO17 C14 TACH1 / GPIO1 F13 TACH2 / GPIO6 A14 TACH3 / GPIO7 G15 TACH4 / GPIO68 C16 268 Ballout Definition Table 6-2. Mobile PCH Ballout by Signal Name (Sheet 10 of 16) 269 Table 6-2. Mobile PCH Ballout by Signal Name (Sheet 11 of 16) Table 6-2. Mobile PCH Ballout by Signal Name (Sheet 12 of 16) EDS Net Name Rev 0.7 Pin # EDS Net Name Rev 0.7 Pin # EDS Net Name Rev 0.7 Pin # VCC AE22 VCCCLK3_3 M29 VGA_IRTN U39 VCC AE24 VCCCLK3_3 U32 VGA_RED V45 VCC AE26 VCCCLK3_3 V32 VGA_VSYNC N44 VCC AG18 VCCDSW3_3 A16 VSS A2 VCC AG20 VCCIO U30 VSS A4 VCC AG22 VCCIO U36 VSS A5 VCC AG24 VCCIO V28 VSS A41 VCC AP45 VCCIO V30 VSS A43 VCC3_3 L24 VCCIO Y30 VSS A44 VCC3_3 R30 VCCIO AK18 VSS B1 VCC3_3 R32 VCCIO AK20 VSS B2 VCC3_3 AE14 VCCIO AK22 VSS B7 VCC3_3 AF12 VCCIO AM18 VSS B11 VCC3_3 AG14 VCCIO AM20 VSS B15 VCC3_3 AK30 VCCIO AM22 VSS B19 VCC3_3 AK32 VCCIO AN34 VSS B23 VCCADAC1_5 P45 VCCIO AN35 VSS B27 VCCADACBG3_3 M31 VCCIO AP22 VSS B31 VCCASW L17 VCCIO AR22 VSS B35 VCCASW R18 VCCIO AT22 VSS B39 VCCASW U18 VCCRTC A6 VSS B44 VCCASW U20 VCCSPI AD12 VSS B45 VCCASW U22 VCCSUS3_3 K8 VSS C45 VCCASW U24 VCCSUS3_3 R20 VSS D1 VCCASW V18 VCCSUS3_3 R22 VSS D4 VCCASW V20 VCCSUS3_3 R24 VSS D25 VCCASW V22 VCCSUS3_3 R26 VSS D42 VCCASW V24 VCCSUS3_3 R28 VSS E1 VCCASW Y18 VCCSUS3_3 U26 VSS E45 VCCASW Y20 VCCSUS3_3 AJ30 VSS F15 VCCASW Y22 VCCSUS3_3 AJ32 VSS F20 VCCASW AA18 VCCSUSHDA A26 VSS F29 VCCCLK Y32 VCCUSBPLL U35 VSS F33 VCCCLK AA30 VCCVRM AF34 VSS F43 VCCCLK AA32 VCCVRM AK26 VSS G2 VCCCLK AD34 VCCVRM AK28 VSS G8 VCCCLK AD35 VCCVRM AN11 VSS G38 VCCCLK AD36 VCCVRM AW40 VSS G44 VCCCLK AE30 VCCVRM BB44 VSS H7 VCCCLK AE32 VCCVRM BE22 VSS H10 VCCCLK AG30 VGA_BLUE T45 VSS H13 VCCCLK AG32 VGA_DDC_CLK M43 VSS H17 VCCCLK3_3 L26 VGA_DDC_DATA M45 VSS H22 VCCCLK3_3 L29 VGA_GREEN U44 VSS H24 VCCCLK3_3 M26 VGA_HSYNC N42 VSS H26 Datasheet Ballout Definition Table 6-2. Mobile PCH Ballout by Signal Name (Sheet 13 of 16) Datasheet Table 6-2. Mobile PCH Ballout by Signal Name (Sheet 14 of 16) Table 6-2. Mobile PCH Ballout by Signal Name (Sheet 15 of 16) EDS Net Name Rev 0.7 Pin # EDS Net Name Rev 0.7 Pin # EDS Net Name Rev 0.7 Pin # VSS H31 VSS V43 VSS AJ24 VSS H36 VSS W2 VSS AJ34 VSS H40 VSS W44 VSS AJ38 VSS K10 VSS Y8 VSS AK14 VSS K15 VSS Y14 VSS AK16 VSS K20 VSS Y16 VSS AK24 VSS K29 VSS Y24 VSS AK43 VSS K33 VSS Y28 VSS AK45 VSS K39 VSS Y34 VSS AL2 VSS L2 VSS Y36 VSS AL8 VSS L44 VSS Y40 VSS AL12 VSS M17 VSS AA4 VSS AL34 VSS M22 VSS AA16 VSS AL38 VSS M24 VSS AA20 VSS AM14 VSS N6 VSS AA22 VSS AM16 VSS N10 VSS AA28 VSS AM24 VSS N12 VSS AB8 VSS AM26 VSS N35 VSS AB12 VSS AM28 VSS N39 VSS AB34 VSS AM30 VSS P22 VSS AB38 VSS AM32 VSS P24 VSS AC2 VSS AN8 VSS P26 VSS AC44 VSS AN36 VSS P28 VSS AD6 VSS AN40 VSS P30 VSS AD8 VSS AN42 VSS P32 VSS AD14 VSS AP13 VSS P43 VSS AD16 VSS AP24 VSS R2 VSS AD18 VSS AP31 VSS R8 VSS AD30 VSS AP43 VSS R12 VSS AD32 VSS AR2 VSS R14 VSS AD40 VSS AT10 VSS R16 VSS AE16 VSS AT15 VSS R34 VSS AE28 VSS AT17 VSS R38 VSS AF8 VSS AT20 VSS R44 VSS AF38 VSS AT26 VSS T43 VSS AG2 VSS AT29 VSS U6 VSS AG16 VSS AT36 VSS U10 VSS AG26 VSS AT38 VSS U16 VSS AG28 VSS AT43 VSS U28 VSS AG44 VSS AV6 VSS U34 VSS AJ6 VSS AV7 VSS U38 VSS AJ8 VSS AV13 VSS U42 VSS AJ16 VSS AV22 VSS V14 VSS AJ18 VSS AV24 VSS V16 VSS AJ20 VSS AV31 VSS V26 VSS AJ22 VSS AV33 270 Ballout Definition Table 6-2. Mobile PCH Ballout by Signal Name (Sheet 16 of 16) EDS Net Name Rev 0.7 Pin # VSS AV40 VSS AW2 VSS AY7 VSS AY10 VSS AY15 VSS AY20 VSS AY26 VSS AY29 VSS AY36 VSS BA1 VSS BA40 VSS BB25 VSS BB42 VSS BC1 VSS BC16 VSS BC22 VSS BC28 VSS BD1 VSS BD2 VSS BD7 VSS BD11 VSS BD15 VSS BD19 VSS BD31 VSS BD35 VSS BD39 VSS BD44 VSS BD45 VSS BE2 VSS BE3 VSS BE5 VSS BE41 WAKE# K3 XTAL25_IN AM43 XTAL25_OUT AL44 Datasheet 271 Package Information 7 Package Information 7.1 Desktop/Server PCH Package * FCBGA package * Package size: 23 mm x 22 mm * Z Height: 1.602 mm * Ball Count: 708 * Ball pitch: 0.65 mm The Desktop/Server PCH package information is shown in Figure 7-2. Note: All dimensions, unless otherwise specified, are in millimeters. 7.1.1 Tape and Reel Pin 1 Placement Figure 7-1. Tape and Reel Pin 1 Location 272 Datasheet Package Information Figure 7-2. Datasheet Desktop / Server PCH Package Drawing 273 Package Information 7.2 Mobile PCH Package * FCBGA package * Package size: 20 mm x 20 mm * Z Height: 1.573 mm * Ball Count: 695 * Ball pitch: 0.593 mm The Mobile PCH package information is shown in Figure 7-4. Note: All dimensions, unless otherwise specified, are in millimeters. 7.2.1 Tape and Reel Pin 1 Placement Figure 7-3. Tape and Reel Pin 1 Location 274 Datasheet Package Information Figure 7-4. Mobile PCH Package Drawing Datasheet 275 Electrical Characteristics 8 Electrical Characteristics This chapter contains the DC and AC characteristics for the PCH. AC timing diagrams are included. 8.1 Thermal Specifications 8.1.1 Storage Specifications and Thermal Design Power (TDP) Additional desktop thermal information can be obtained in the Intel(R) 8 Series / C220 Series Chipset Family Platform Controller Hub (PCH) Thermal Mechanical Specifications and Design Guide (document number 328906). Table 8-1. Storage Conditions and Thermal Junction Operating Temperature Limits Parameter Description Min Max Notes TABSOLUTE STORAGE The non-operating device storage temperature. Damage (latent or otherwise) may occur when exceeded for any length of time. -25 C 125 C 1,2,3 TSUSTAINED STORAGE The ambient storage temperature (in shipping media) for a sustained period of time. -5 C 40 C 4,5 RHSUSTAINED STORAGE The maximum device storage relative humidity for a sustained period of time. TIME SUSTAINED STORAGE A prolonged or extended period of time; typically associated with customer shelf life. Tj Thermal Junction Operating Temperature limits. Tcatastrophic Thermal Junction Catastrophic Temperature limits. 60% @ 24 C 5,6 0 Months 6 Months 6 0 C 108 C 7 110 C 128 C 8 Notes: 1. Refers to a component device that is not assembled in a board or socket and is not electrically connected to a voltage reference or I/O signal. 2. Specified temperatures are not to exceed values based on data collected. Exceptions for surface mount reflow are specified by the applicable JEDEC standard. Non-adherence may affect PCH reliability. 3. TABSOLUTE STORAGE applies to the unassembled component only and does not apply to the shipping media, moisture barrier bags, or desiccant. 4. Intel branded products are specified and certified to meet the following temperature and humidity limits that are given as an example only (Non-Operating Temperature Limit: -40 C to 70 C and Humidity: 50% to 90%, non-condensing with a maximum wet bulb of 28 C.) Post board attach storage temperature limits are not specified for non-Intel branded boards. 5. The JEDEC J-JSTD-020 moisture level rating and associated handling practices apply to all moisture sensitive devices removed from the moisture barrier bag. 6. Nominal temperature and humidity conditions and durations are given and tested within the constraints imposed by TSUSTAINED storage and customer shelf life in applicable Intel boxes and bags. 7. The thermal solution needs to ensure that the temperature does not exceed the maximum junction temperature (Tj,max) limit. 8. Default Catastrophic Trip Point for PCH is 120 C. Table 8-2. 276 Mobile Thermal Design Power SKU Thermal Design Power (TDP) Standard 3 Watts Notes Datasheet Electrical Characteristics 8.2 Absolute Maximum Ratings Table 8-3. PCH Absolute Maximum Ratings Parameter Maximum Limits Voltage on any 3.3 V Pin with respect to Ground -0.5 to Vcc3_3 + 0.4 V Voltage on any 1.5 V Pin with respect to Ground -0.5 to VccVRM + 0.5 V Voltage on any 1.05 V Tolerant Pin with respect to Ground -0.5 to VccCore + 0.5 V 1.05 V Supply Voltage with respect to VSS -0.5 to 1.3 V 3.3 V Supply Voltage with respect to VSS -0.5 to 3.7 V V_PROC_IO Supply Voltage with respect to VSS -0.5 to 1.3 V 1.5 V Supply Voltage for the analog PLL with respect to VSS -0.5 to 1.65 V Table 8-3 specifies absolute maximum and minimum ratings. At conditions outside functional operation condition limits, but within absolute maximum and minimum ratings, neither functionality nor long-term reliability can be expected. If a device is returned to conditions within functional operation limits after having been subjected to conditions outside these limits (but within the absolute maximum and minimum ratings) the device may be functional, but with its lifetime degraded depending on exposure to conditions exceeding the functional operation condition limits. At conditions exceeding absolute maximum and minimum ratings, neither functionality nor long-term reliability can be expected. Moreover, if a device is subjected to these conditions for any length of time, it will either not function or its reliability will be severely degraded when returned to conditions within the functional operating condition limits. Although the PCH contains protective circuitry to resist damage from Electrostatic Discharge (ESD), precautions should always be taken to avoid high static voltages or electric fields. 8.3 PCH Power Supply Range Table 8-4. PCH Power Supply Range Note: Datasheet Power Supply Minimum Nominal Maximum 1.05 V 0.998 V 1.05 V 1.10 V 1.5 V 1.43 V 1.50 V 1.58 V 1.8 V 1.71 V 1.80 V 1.89 V 3.3 V 3.14 V 3.30 V 3.47 V VccRTC can drop to 2.0Vmin in G3 state. Refer to Table 8-8 for more details. 277 Electrical Characteristics 8.4 General DC Characteristics Table 8-5. Measured Silicon ICC9 (Desktop and Mobile) Voltage (V) S0 Iccmax Current Integrated Graphics3 (A) S0 Iccmax Current External Graphics3 (A) S0 Idle Current External Graphics3 (A) S0 Idle Current Integrated Graphics3 (A) Sx Iccmax Current3, 4 (A) Sx Idle Current3, 4 (A) G3 VCC (Internal Suspend VR mode using INTVRMEN)7 1.05 1.312 1.312 0.130 0.130 0 0 0 VCC (External Suspend VR mode using INTVRMEN)7 1.05 1.138 1.138 0.114 0.114 0 0 0 VCCIO 1.05 3.629 3.491 0.199 0.264 0 0 0 Voltage Rail VCCADAC1_5 1.5 0.070 0.004 0.002 0.070 0 0 0 VCCADAC3_3 3.3 0.0133 <1 mA <1 mA 0.007 0 0 0 VCCCLK 1.05 0.306 0.306 0.089 0.089 0 0 0 VCCCLK3_3 3.3 0.055 0.055 0.011 0.011 0 0 0 VCCVRM 1.5 0.183 0.158 0.043 0.068 0 0 0 VCC3_3 3.3 0.133 0.133 0.003 0.003 0 0 0 VCCASW VCCSUSHDA 1.05 0.670 0.670 0.034 0.034 0.211 0.034 0 3.3/1.5 0.010 0.010 <1 mA <1 mA 0.003 <1 mA 0 VCCSPI5 3.3 0.022 0.022 <1 mA <1 mA 0 0 0 VCCSUS3_3 (Internal Suspend VR mode using INTVRMEN)7 3.3 0.261 0.261 0.006 0.006 0.054 0.020 0 VCCSUS3_3 (External Suspend VR mode using INTVRMEN)7 3.3 0.261 0.261 0.006 0.006 0.054 0.004 0 VCCDSW3_36 3.3 0.015 0.015 1.5 mA 1.5 mA 1.5 mA 1.5 mA 0 VCCRTC 3.3 N/A N/A N/A N/A N/A N/A 6 uA See notes 1, 2 V_PROC_IO 1.05 0.004 0.004 0.002 0.002 0 0 0 DcpSus1 (External Suspend VR mode using INTVRMEN)7,8 1.05 0.098 0.098 0.012 0.012 0.012 0.012 0 DcpSus2 (External Suspend VR mode using INTVRMEN)7,8 1.05 0.028 0.028 0.002 0.002 0.002 0.002 0 DcpSus3 (External Suspend VR mode using INTVRMEN)7,8 1.05 0.476 0.476 0.003 0.003 0.005 0.005 0 Notes: 1. G3 state shown to provide an estimate of battery life. 2. Icc (RTC) data is taken with VccRTC at 3.0 V while the system in a mechanical off (G3) state at room temperature. 3. S0 Iccmax Measurements taken at 110 C and S0 Idle/Sx Iccmax/Sx Idle measurements taken at 50 C. 4. Sx/M-Off Iccmax and Icc Idle values can be derived by removing VCCASW current in Sx. 5. If VCCSPI follows ASW well, the Iccmax and Icc Idle values will also be 0 in Sx/M-Off. 6. DeepSx Icc values can be derived by removing all Sx Iccmax and Icc Idle values except for VCCDSW3_3. 278 Datasheet Electrical Characteristics 7. 8. External Suspend VR mode supported on Mobile Only. This applies to External Suspend VR powered mode. In Internal Suspend VR mode DcpSus1, DcpSus2 and DcpSus3 is a No Connect and hence Iccmax and Icc Idle information is not applicable. 9.The ICCmax value is a steady state current that can happen after respective Power OK has asserted (or Reset signal has deasserted). Table 8-6. Type Single-Ended Signal DC Characteristics as Inputs or Outputs (Sheet 1 of 5) Symbol Parameter Min Max Unit Condition Associated Signals: HAD_DOCK_EN#/GPIO33, PLTRST#, SPKR, PME#, BMBUSY#/GPIO0, GPIO35/NMI#, GPIO15, GPIO27, GPIO28, CLKRUN#/GPIO32, BATLOW#/GPIO72, SERIRQ, GPIO8, CLKIN_33MHZLOOPBACK LDRQ1#/GPIO23, LDRQ0#, LAD3, LAD2, LAD1, LAD0, LFRAME# Input Output VCC Supply Voltage Reference 3.14 3.47 V VIH Input High Voltage 0.5 x VCC VCC + 0.5 V VIL Input Low Voltage -0.5 0.3 x VCC V IIL Input Leakage Current -10 10 uA CIN Pin Input Capacitance -- 10 pF VOH Output High Voltage 0.9 x VCC -- V IOH=-0.5mA VOL Output Low Voltage -- 0.1 x VCC V IOL=1.5mA Output 4 VCC Supply Voltage Reference 3.14 3.47 V VIH Input High Voltage 0.5 x VCC VCC + 0.5 V VIL Input Low Voltage -0.5 0.3 x VCC V IIL Input Leakage Current -10 10 uA CIN Pin Input Capacitance -- 10 pF VOH Output High Voltage 0.9 x VCC -- V IOH=-0.5mA VOL Output Low Voltage -- 0.1 x VCC V IOL=1.5mA Datasheet VCC Supply Voltage Reference CPIN Pin Capacitance 1 2 3 4 1 2 Associated Signals: VGA_HSYNC, VGA_VSYNC Output 2 3 Associated Signals: PCIECLKRQ0#/GPIO73, PCIECLKRQ1#/GPIO18, PCIECLKRQ2#/GPIO20/SMI#, PCIECLKRQ3#/GPIO25, PCIECLKRQ4#/ GPIO26, PCIECLKRQ5#/GPIO44, PCIECLKRQ6#/GPIO45, PCIECLKRQ7#/GPIO46 SATA0GP/GPIO21, SATA1GP/GPIO19, SATA2GP/GPIO36, SATA3GP/GPIO37, SATA4GP/GPIO16, SATA5GP/GPIO49 OC0#/GPIO59, OC1#/GPIO40, OC2#/GPIO41, OC3#/GPIO42, OC4#/GPIO43, OC5#/GPIO9, OC6#/GPIO10, OC7#/ GPIO14 PEG_A_CLKRQ#/GPIO47, PEG_B_CLKRQ#/GPIO56, SPI_CLK, SPI_CS0#, SPI_CS1#, SPI_CS2#, SPI_MISO, SPI_MOSI, SPI_IO2, SPI_IO3 LAN_PHY_PWR_CTRL/GPIO12 Input Notes 3.14 3.47 V -- 10 pF VOH Output High Voltage 2.4 VCC V IOH=-8mA VOL Output Low Voltage -- 0.5 V IOL=8mA 1 279 Electrical Characteristics Table 8-6. Type Single-Ended Signal DC Characteristics as Inputs or Outputs (Sheet 2 of 5) Symbol Parameter Min Max Unit Condition Notes Associated Signals: GPIO24, GPIO34, GPIO57, GPIO51, GPIO54, GPIO52, GPIO53, GPIO50, SYS_RESET#, DPWROK, DRAMPWROK, CL_RST#, RI#, SUS_STAT#/GPIO61, SUSACK#, SUSCLK/GPIO62, PWRBTN#, SUSWARN#/SUSPWRNACK/GPIO30, WAKE#, ACPRESENT/GPIO31, SATALED# SLP_S3#, SLP_S4#, SLP_S5#/GPIO63, SLP_SUS#, SLP_WLAN#/GPIO29, SLP_A#, SLP_LAN# TACH0/GPIO17, TACH1/GPIO1, TACH2/GPIO6, TACH3/GPIO7, TACH4/GPIO68, TACH5/GPIO69, TACH6/GPIO70, TACH7/GPIO71 PIRQA#, PIRQB#, PIRQC#, PIRQD#, PIRQE#/GPIO2, PIRQF#/GPIO3, PIRQG#/GPIO4, PIRQH#/GPIO5 Input Output VCC Supply Voltage Reference 3.14 3.47 V VHYS Schmitt Trigger Hysteresis 250 -- mVpp VIH Input High Voltage 2 VCC + 0.5 V VIL Input Low Voltage -0.5 0.8 V IIL Input Leakage Current -10 10 uA CIN Pin Input Capacitance -- 10 pF VOH Output High Voltage VCC - 0.5 VCC V IOH=-2mA VOL Output Low Voltage -- 0.4 V IOL=4.5mA 2 1 Associated Signals: SCLOCK/GPIO22, SDATAOUT0/GPIO39, SDATAOUT1/GPIO48, SLOAD/GPIO38, GPIO55 Input Output 2 VCC Supply Voltage Reference 3.14 3.47 V VHYS Schmitt Trigger Hysteresis 250 -- mVpp V VIH Input High Voltage 2 VCC + 0.5 VIL Input Low Voltage -0.5 0.8 V IIL Input Leakage Current -10 10 uA CIN Pin Input Capacitance -- 10 pF VOH Output High Voltage 2.4 VCC V IOH=-2mA VOL Output Low Voltage -- 0.4 V IOL=12mA 1 Associated Signals: SMBALERT#/GPIO11, SMBCLK, SMBDATA, SML0ALERT#/GPIO60, SML0CLK, SML0DATA, SML1ALERT#/TEMP_ALERT#/ GPIO74, SML1CLK/GPIO58, SML1DATA/GPIO75 Input Output VCC Supply Voltage Reference 3.14 3.47 V VIH Input High Voltage 2 VCC + 0.5 V VIL Input Low Voltage -0.5 0.8 V IIL Input Leakage Current -10 10 uA CIN Pin Input Capacitance -- 10 pF VOH Output High Voltage 2.4 VCC V IOH=-4mA VOL Output Low Voltage -- 0.4 V IOL=4mA Associated Signals: PWM0, PWM1, PWM2, PWM3 Input Output 280 2 1 2 VCC Supply Voltage Reference 3.14 3.47 V VIH Input High Voltage 2 VCC + 0.5 V VIL Input Low Voltage -0.5 0.8 V IIL Input Leakage Current -10 10 uA CIN Pin Input Capacitance -- 10 pF VOH Output High Voltage 2.4 VCC V VOL Output Low Voltage -- 0.4 V 1 IOL=8mA Datasheet Electrical Characteristics Table 8-6. Type Single-Ended Signal DC Characteristics as Inputs or Outputs (Sheet 3 of 5) Symbol Parameter Min Max Unit Condition Associated Signals: eDP_VDDEN, eDP_BKLTEN, eDP_BKLTCTL DDPB_CTRLDATA, DDPB_CTRLCLK, DDPC_CTRLDATA, DDPC_CTRLCLK, DDPD_CTRLDATA, DDPD_CTRLCLK VGA_DDC_DATA, VGA_DDC_CLK Input Output VCC Supply Voltage Reference 3.14 3.47 V VHYS Schmitt Trigger Hysteresis 0.05 x VCC -- mVpp VIH Input High Voltage 0.7 x VCC VCC + 0.5 V VIL Input Low Voltage -0.5 0.3 x VCC V IIL Input Leakage Current -10 10 uA CIN Pin Input Capacitance -- 10 pF VOH Output High Voltage VCC - 0.5 VCC V IOH=-2mA VOL Output Low Voltage 0.0 0.4 V IOL=3mA Associated Signals: RCIN#, SYS_PWROK, APWROK Input Output VCC Supply Voltage Reference 3.14 3.47 V VHYS Schmitt Trigger Hysteresis 250 -- mVpp VIH Input High Voltage 2.1 3.3 V VIL Input Low Voltage -- 0.8 V IIL Input Leakage Current -10 10 uA CIN Pin Input Capacitance -- 50 pF Output Datasheet 1 2 VCC Supply Voltage Reference 0.94 1.13 V VHYS Schmitt Trigger Hysteresis 250 -- mVpp VIH Input High Voltage 0.75 VCC + 0.5 V VIL Input Low Voltage -0.5 0.3 V IIL Input Leakage Current -10 10 uA CIN Pin Input Capacitance -- 10 pF VOH Output High Voltage 0.75 -- V IOH=-0.5mA VOL Output Low Voltage -- 0.3 V IOL=0.5mA Associated Signals: SST Input 2 2 Associated Signals: JTAG_TCK, JTAG_TDI, JTAG_TDO, JTAG_TMS Input Notes 1 2 VCC Supply Voltage Reference 1.43 1.58 V VHYS Schmitt Trigger Hysteresis 100 -- mVpp VIH Input High Voltage 1.1 -- V VIL Input Low Voltage IIL Input Leakage Current -- 0.4 V -10 10 uA CIN Pin Input Capacitance -- 10 pF VOH Output High Voltage 1.1 -- V IOH=-6mA VOL Output Low Voltage -- 0.4 V IOL=0.5mA 1 281 Electrical Characteristics Table 8-6. Type Single-Ended Signal DC Characteristics as Inputs or Outputs (Sheet 4 of 5) Symbol Parameter Min Max Unit Condition Associated Signals: PECI Input Output 2 VCC Supply Voltage Reference 0.9 1.15 V VHYS Schmitt Trigger Hysteresis 0.1 x VCC -- mVpp Vn Negative edge threshold voltage 0.275 x VCC 0.500 x VCC V Vp Positive edge threshold voltage 0.550 x VCC 0.725 x VCC V VIN Input Voltage Range -0.15 VCC + 0.15 V VOH Output High Voltage 0.75 x VCC -- V IOH=-6mA VOL Output Low Voltage -- 0.25 x VCC V IOL=1mA Associated Signals: PROCPWRGD, PLTRST_PROC#, PMSYNCH, THRMTRIP# Input Output Output 1 2 VCC Supply Voltage Reference 0.9 1.15 V VHYS Schmitt Trigger Hysteresis 0.1 x VCC -- mVpp VIH Input High Voltage 0.81 x VCC -- V VIL Input Low Voltage -- 0.51 x VCC V IIL Input Leakage Current -10 10 uA CIN Pin Input Capacitance -- 10 pF VOH Output High Voltage VCC - 0.3 -- V IOH=-3mA VOL Output Low Voltage -- 0.255 V IOL=3mA Associated Signals: CL_DATA, CL_CLK Input Notes 1 2 CL_VRef Supply Voltage Reference VHYS Schmitt Trigger Hysteresis 0.12 x VCCSUS3_3 0.12 x VCCSUS3_3 V 100 -- mVpp VIH Input High Voltage CL_VRef + 0.075 -- V VIL Input Low Voltage -- CL_VRef0.075 V IIL Input Leakage Current -10 10 uA CIN Pin Input Capacitance -- 10 pF VOH Output High Voltage 610 -- mV IOH=-6.1mA VOL Output Low Voltage -- 150 mV IOL=1mA Associated Signals: HDA_RST#, HDA_SDI0, HDA_SDI1, HDA_SDI2, HDA_SDI3, HDA_SDO, HDA_SYNC, HDA_DOCK_RST#/GPIO13, HDA_BCLK 1 2 3.3 V Operation Input 282 VCC Supply Voltage Reference 3.0 3.6 V LPIN Input Pin Inductance VIH Input High Voltage -- 20 nH 0.65 x VCC VCC + 0.5 VIL Input Low Voltage -0.5 0.35 x Vcc V V IIL Input Leakage Current -10 10 uA CIN Pin Input Capacitance -- 7.5 pF Datasheet Electrical Characteristics Table 8-6. Single-Ended Signal DC Characteristics as Inputs or Outputs (Sheet 5 of 5) Type Symbol Output VOH Output High Voltage Parameter VOL Output Low Voltage Min Max Unit Condition Notes 0.9 x VCC -- V IOH=-0.5mA 1 -- 0.1 x VCC V IOL=1.5mA 1.5 V Operation Input Output VCC Supply Voltage Reference LPIN Input Pin Inductance 1.35 1.65 V -- 20 nH V VIH Input High Voltage 0.60 x VCC VCC + 0.5 VIL Input Low Voltage -0.5 0.4 x Vcc V IIL Input Leakage Current -10 10 uA CIN Pin Input Capacitance -- 7.5 pF VOH Output High Voltage 0.9 x VCC -- V IOH=-0.5mA VOL Output Low Voltage -- 0.1 x VCC V IOL=1.5mA 1 Associated Signals: RSMRST#, INTVRMEN, SRTCRST#, INTRUDER#, PWROK, DPWROK, DSWVRMEN VIL_RTC1 Input Low Voltage -0.5 0.78 V VIH_RTC1 Input High Voltage 2.0 VCCRTC+0.5 V 6 Associated Signals: RTCRST# VIL_RTC2 Input Low Voltage -0.5 0.78 V VIH_RTC2 Input High Voltage 2.0 VCCRTC+0.5 V 6 Associated Signals: RTCX1 VIL_RTC3 Input Low Voltage -0.5 0.1 V VIH_RTC3 Input High Voltage 0.8 1.2 V Associated Signals: XTAL25_IN, XTAL25_OUT VIL Maximum Input Low Voltage -0.25 0.15 V VIH Minimum Input High Voltage 0.7 1.2 V 0.998 1.10 V Associated Signals: FDI_CSYNC, FDI_INT VCC Supply Voltage Reference Input Leakage Current 2 Input IIL -- 100 uA Output VOH Output High Voltage 0.75 -- V IOH=-0.5mA VOL Output Low Voltage -- 0.3 V IOL=0.5mA 1 Notes: 1. The VOH specification does not apply to open-collector or open-drain drivers, which does not apply when the pin is configured as GPIO. Signals of this type must have an external pull-up resistor, and that's what determines the high-output voltage level. Refer to Chapter 2, "Signal Description"for details on signal types. 2. Input characteristics apply when a signal is configured as Input or to signals that are only Inputs. Output characteristics apply when a signal is configured as an Output or to signals that are only Outputs. Refer to Chapter 2 for details on signal types. 3. PME# Input Current Leakage is 1uA max 4. CLKIN_33MHZLOOPBACK has a pin capacitance in the range of 1 pF to 12 pF. 5. Only applies to FAST MODE (400 kbits/s). 6. VCCRTC is the voltage applied to the VCCRTC well of the PCH. When the system is in a G3 state, this is generally supplied by the coin cell battery, but for S5 and greater, this is generally VCCSUS3_3 Datasheet 283 Electrical Characteristics Table 8-7. Differential Signal DC Characteristics (Sheet 1 of 3) Symbol Parameter Min Max Unit Notes 1 Associated Signals: PETp[10:1], PETn[10:1], PERp[10:1], PERn[10:1] Generation 1 Differential Peak to Peak Output Voltage 0.8 1.2 V VTX-DIFF P-P - Low Low power differential Peak to Peak Output Voltage 0.4 1.2 V VTX_CM-ACp TX AC Common Mode Output Voltage (2.5GT/s) -- 20 mV ZTX-DIFF-DC DC Differential TX Impedance 80 120 VRX-DIFF p-p Differential Input Peak to Peak Voltage 0.175 1.2 V VRX_CM-ACp AC peak Common Mode Input Voltage -- 150 mV VTX-DIFF P-P Differential Peak to Peak Output Voltage 0.8 1.2 V VTX-DIFF P-P - Low Low power differential Peak to Peak Output Voltage 0.8 1.2 V VTX_CM-Acp-p TX AC Common Mode Output Voltage (5GT/s) -- 100 mV ZTX-DIFF-DC DC Differential TX Impedance -- 120 VRX-DIFF p-p Differential Input Peak to Peak Voltage 0.1 1.2 V VRX_CM-ACp AC peak Common Mode Input Voltage -- 150 mV Differential Peak to Peak Output Voltage 0.8 1.2 V Low power differential Peak to Peak Output Voltage 0.4 1.2 V VTX-DIFF P-P 1 Generation 2 1 1 Associated Signals: USB3R[N/P][6:1], USB3T[N/P][6:1] VTX-DIFF-PP VTX-DIFF P-P - Low 8 Associated Signals: DMI_TX[P/N]_[3:0], DMI_RX[P/N]_[3:0] Generation 1 Differential Peak to Peak Output Voltage 0.4 0.6 V VTX-DIFF P-P - Low Low power differential Peak to Peak Output Voltage 0.4 0.6 V VTX_CM-ACp TX AC Common Mode Output Voltage (2.5GT/s) -- 20 mV ZTX-DIFF-DC DC Differential TX Impedance 80 120 VRX-DIFF p-p Differential Input Peak to Peak Voltage 0.175 1.2 V VRX_CM-ACp AC peak Common Mode Input Voltage -- 150 mV VTX-DIFF P-P Differential Peak to Peak Output Voltage 0.4 0.6 V VTX-DIFF P-P - Low Low power differential Peak to Peak Output Voltage 0.4 0.6 V VTX_CM-Acp-p TX AC Common Mode Output Voltage (5GT/s) -- 100 mV VTX-DIFF P-P Generation 2 284 Datasheet Electrical Characteristics Table 8-7. Differential Signal DC Characteristics (Sheet 2 of 3) Symbol Parameter Min Max Unit ZTX-DIFF-DC DC Differential TX Impedance -- 120 VRX-DIFF p-p Differential Input Peak to Peak Voltage 0.1 1.2 V VRX_CM-ACp AC peak Common Mode Input Voltage -- 150 mV UI Notes Associated Signals: FDI_RXP[1:0] UI Unit Interval 370.37 ps Minimum Rx eye width at the Rx package pins 0.5 -- VTX-DIFF P-P Differential Peak to Peak Input Voltage 175 1000 mV VRX-CM-ACp AC peak input common mode voltage -- 150 mV ZRX-DIFF-DC DC Differential Input Impedance 80 120 TRX-EYE Associated Signals: SATA_RXN[5:0], SATA_RXP[5:0], SATA_TXN[5:0], SATA_TXP[5:0] VIMIN10- Gen1i Minimum Input Voltage - 1.5 Gb/s internal SATA 325 -- mVdiff p-p 2 VIMAX10-Gen1i Maximum Input Voltage - 1.5 Gb/s internal SATA -- 600 mVdiff p-p 2 VIMIN10-Gen1m Minimum Input Voltage - 1.5 Gb/s eSATA 240 -- mVdiff p-p 2 VIMAX10-Gen1m Maximum Input Voltage - 1.5 Gb/s eSATA -- 600 mVdiff p-p 2 VIMIN10-Gen2i Minimum Input Voltage - 3.0 Gb/s internal SATA 275 -- mVdiff p-p 2 VIMAX10-Gen2i Maximum Input Voltage - 3.0 Gb/s internal SATA -- 750 mVdiff p-p 2 VIMIN10-Gen2m Minimum Input Voltage - 3.0 Gb/s eSATA 240 -- mVdiff p-p 2 VIMAX10-Gen2m Maximum Input Voltage - 3.0 Gb/s eSATA -- 750 mVdiff p-p 2 VIMIN10-Gen3i Minimum Input Voltage - 6.0 Gb/s internal SATA 240 -- mVdiff p-p 2 VIMAX10-Gen3i Maximum Input Voltage - 6.0 Gb/s internal SATA -- 1000 mVdiff p-p 2 VOMIN7-Gen1i,m Minimum Output Voltage 1.5 Gb/s eSATA 400 -- mVdiff p-p 3 VOMAX7-Gen1i,m Maximum Output Voltage 1.5 Gb/s eSATA -- 600 mVdiff p-p 3 VOMIN7-Gen2i,m Minimum Output Voltage 3.0 Gb/s internal SATA 400 -- mVdiff p-p 3 VOMAX7-Gen2i,m Maximum Output Voltage 3.0 Gb/s internal SATA -- 700 mVdiff p-p 3 VOMIN7-Gen3i Minimum Output Voltage 6.0 Gb/s internal SATA 200 -- mVdiff p-p 3 VOMAX7-Gen3i Maximum Output Voltage 6.0 Gb/s internal SATA -- 900 mVdiff p-p 3 Datasheet 285 Electrical Characteristics Table 8-7. Differential Signal DC Characteristics (Sheet 3 of 3) Symbol Parameter Min Max Unit Notes Associated Signals: USB2n[13:0], USB2p[13:0] VDI Differential Input Sensitivity classic mode 0.2 -- V 4, 6 VCM Differential Common Mode Range - classic mode 0.8 2.5 V 5, 6 VSE Single-Ended Receiver Threshold - classic mode 0.8 2 V 6 VCRS Output Signal Crossover Voltage - classic mode 1.3 2 V 6 HS Squelch Detection Threshold - HS mode 100 150 mV 7 HS Disconnect Detection Threshold - HS mode 525 625 mV 7 VHSCM HS Data Signaling Common Mode Voltage Range - HS mode -50 500 mV 7 VHSOI HS Idle Level -HS mode -10 10 mV 7 VHSOH HS Data Signaling High -HS mode 360 440 mV 7 VHSOL HS Data Signaling Low -HS mode -10 10 mV 7 VHSSQ VHSDSC VCHIRPJ Chirp J Level -HS mode 700 1100 mV 7 VCHIRPK Chirp K Level -HS mode -900 -500 mV 7 VOL Output Low Voltage -- 0.4 V 6 VOH Output High Voltage 3.3 V - 0.5 -- V 6 Notes: 1. PCI Express mVdiff p-p = 2*|PETp[x] - PETn[x]|; PCI Express mVdiff p-p = 2*|PERp[x] - PERn[x]| 2. SATA Vdiff, RX (VIMAX/VIMIN) is measured at the SATA connector on the receiver side (generally, the motherboard connector), where SATA mVdiff p-p = 2*|SATA[x]RXP - SATA[x]RXN|. 3. SATA Vdiff, tx (VOMIN/VOMAX) is measured at the SATA connector on the transmit side (generally, the motherboard connector), where SATA mVdiff p-p = 2*|SATA[x]TXP - SATA[x]TXN| 4. VDI = | USBPx[P] - USBPx[N] | 5. Includes VDI range 6. Applies to Low-Speed/Full-Speed USB 7. Applies to High-Speed USB 2.0. 8. USB 3.0 mVdiff p-p = 2*|USB3Rp[x] - USB3Rn[x]|; USB 3.0 mVdiff p-p = 2*|USB3Tp[x] - USB3Tn[x]| 9. Max PCIe* DC voltage is 3.6 V, as specified in PCIe spec, and maximum spike should not exceed 5.4 V as specified in JEDEC specification JESD78. Table 8-8. Other DC Characteristics (Sheet 1 of 2) Symbol Min Nom Max Unit Notes Processor I/F .998 1.05 1.10 V 1 Vcc3_3 I/O Buffer Voltage 3.14 3.3 3.47 V 1 VccVRM Internal PLL and VRMs 1.455 1.5 1.545 V 1, 3 3.14 3.3 3.47 V 1 V_PROC_IO VccSus3_3 Suspend Well I/O Buffer Voltage VccIO Core Well I/O buffers .998 1.05 1.10 V 1 VccSPI 3.3 V Supply for SPI Controller Logic 3.14 3.3 3.47 V 1 1.05 V Supply for Intel(R) Management Engine and Integrated LAN .998 1.05 1.10 V 1 2 -- 3.47 V 1 3.14 3.3 3.47 V 1 VccASW VccRTC (G3-S0) VccSusHDA 286 Parameter Battery Voltage Intel High Definition Audio Controller Suspend Voltage Datasheet Electrical Characteristics Table 8-8. Other DC Characteristics (Sheet 2 of 2) Symbol Parameter Min Nom Max Unit Notes VccSusHDA (low voltage) Intel High Definition Audio Controller Low Voltage Mode Suspend Voltage 1.43 1.5 1.58 V 1 VccADAC Display DAC Analog Power. This power is supplied by the core well. 3.14 3.3 3.47 V 1 3.3 V supply for Deep Sx wells 3.14 3.3 3.47 V 1 VccDSW3_3 Notes: 1. The I/O buffer supply voltage is measured at the PCH package pins. The tolerances shown in Table 8-8 are inclusive of all noise from DC up to 20 MHz. In testing, the voltage rails should be measured with a bandwidth limited oscilloscope that has a rolloff of 3 dB/decade above 20 MHz. 2. Includes Single Ended clocks REFCLK14IN, CLKOUTFLEX[3:0] and PCICLKIN. 3. Includes only DC tolerance. AC tolerance will be 2% in addition to this range. 8.5 Display DC Characteristics Table 8-9. Signal Groups Signal Group VGA DAC Digital DisplayPort Auxilliary Associated Signals Note VGA_RED, VGA_GREEN, VGA_BLUE, VGA_IRTN DDP[D:B]_AUX[P,N] Table 8-10. CRT DAC Signal Group DC Characteristics: Functional Operating Range (VccADAC = 3.3 V 5%) Parameter Min Nom Max Unit Notes -- 8 -- Bits 1 0.665 0.7 0.77 V 1, 2, 4 white video level voltage Min Luminance -- 0 -- V 1, 3, 4 black video level voltage LSB Current -- 73.2 -- uA 4, 5 Integral Linearity (INL) -1 -- 1 LSB 1, 6 Differential Linearity (DNL) -1 -- 1 LSB 1, 6 Video channel-channel voltage amplitude mismatch -- -- 6 % 7 DAC Resolution Max Luminance (full-scale) Monotonicity Yes Notes: 1. Measured at each R, G, B termination according to the VESA* Test Procedure - Evaluation of Analog Display Graphics Subsystems Proposal (Version 1, Draft 4, December 1, 2000). 2. Max steady-state amplitude 3. Min steady-state amplitude 4. Defined for a double 75- termination. 5. Set by external reference resistor value. 6. INL and DNL measured and calculated according to VESA video signal standards. 7. Max full-scale voltage difference among R,G,B outputs (percentage of steady-state full-scale voltage). Datasheet 287 Electrical Characteristics Table 8-11. Display Port Auxiliary Signal Group DC Characteristics Symbol Parameter Vaux-diff-p-p Nom Max Unit Aux peak-to-peak voltage at a transmitting devices 0.39 -- 1.38 V Aux peak-to-peak voltage at a receiving devices 0.32 -- 1.36 V -- 100 -- V Vaux-term-R AUX CH termination DC resistance V-aux-dc-cm AUX DC common mode voltage 0 -- 2 Aux turn around common mode voltage -- 0.4 V V-aux_turn-CM 8.6 Min AC Characteristics Table 8-12. PCI Express* Interface Timings Symbol Parameter Min Max Unit Figures Notes Transmitter and Receiver Timings UI Unit Interval - PCI Express* Gen 1 (2.5 GT/s) 399.88 400.12 ps 5 UI Unit Interval - PCI Express* Gen 2 (5.0 GT/s) 199.9 200.1 ps 5 TTX-EYE Minimum Transmission Eye Width 0.7 -- UI TTX-RISE/Fall 8-29 1,2 D+/D- TX Out put Rise/Fall time 0.125 UI 1,2 D+/D- TX Out put Rise/Fall time 0.15 UI 1,2 Minimum Receiver Eye Width 0.40 (Gen1) TTX-RISE/Fall (Gen2) TRX-EYE -- UI 8-30 3,4 Notes: 1. Specified at the measurement point into a timing and voltage compliance test load and measured over any 250 consecutive TX UIs. (Also refer to the Transmitter compliance eye diagram) 2. A TTX-EYE = 0.70 UI provides for a total sum of deterministic and random jitter budget of TTXJITTER-MAX = 0.30 UI for the Transmitter collected over any 250 consecutive TX UIs. The TTXEYE-MEDIAN-to-MAX-JITTER specification ensures a jitter distribution in which the median and the maximum deviation from the median is less than half of the total TX jitter budget collected over any 250 consecutive TX UIs. It should be noted that the median is not the same as the mean. The jitter median describes the point in time where the number of jitter points on either side is approximately equal as opposed to the averaged time value. 3. Specified at the measurement point and measured over any 250 consecutive UIs. The test load documented in the PCI Express* specification 2.0 should be used as the RX device when taking measurements (also refer to the Receiver compliance eye diagram). If the clocks to the RX and TX are not derived from the same reference clock, the TX UI recovered from 3500 consecutive UI must be used as a reference for the eye diagram. 4. A TRX-EYE = 0.40 UI provides for a total sum of 0.60 UI deterministic and random jitter budget for the Transmitter and interconnect collected any 250 consecutive UIs. The TRX-EYE-MEDIAN-to--MAX-JITTER specification ensures a jitter distribution in which the median and the maximum deviation from the median is less than half of the total 0.6 UI jitter budget collected over any 250 consecutive TX UIs. It should be noted that the median is not the same as the mean. The jitter median describes the point in time where the number of jitter points on either side is approximately equal as opposed to the averaged time value. If the clocks to the RX and TX are not derived from the same reference clock, the TX UI recovered from 3500 consecutive UI must be used as the reference for the eye diagram. 5. Nominal Unit Interval is 400 ps for 2.5 GT/s and 200 ps for 5 GT/s. 288 Datasheet Electrical Characteristics Table 8-13. HDMI* Interface Timings (DDP[D:B][3:0]) Symbol Parameter Min Max Unit Figures Notes Transmitter and Receiver Timings UI TTX-EYE TTX-RISE/Fall Unit Interval 600 Minimum Transmission Eye Width D+/D- TX Out put Rise/Fall time TMDS Clock Jitter 4000 ps 0.8 -- UI 1,2 -- 0.125 UI 1,2 -- 0.25 UI T-skew-intrapair Intra pair skew at source connector -- 0.15 TBIT T-skewinter-pair Inter pair skew at source connector -- 0.2 Tchara cter Clock Duty Cycle 10 60% % Duty Cycle Notes: 1. Specified at the measurement point into a timing and voltage compliance test load and measured over any 250 consecutive TX UIs. (Also refer to the Transmitter compliance eye diagram) 2. A TTX-EYE = 0.70 UI provides for a total sum of deterministic and random jitter budget of TTXJITTER-MAX = 0.30 UI for the Transmitter collected over any 250 consecutive TX UIs. The TTXEYE-MEDIAN-to-MAX-JITTER specification ensures a jitter distribution in which the median and the maximum deviation from the median is less than half of the total TX jitter budget collected over any 250 consecutive TX UIs. It should be noted that the median is not the same as the mean. The jitter median describes the point in time where the number of jitter points on either side is approximately equal as opposed to the averaged time value. Table 8-14. Intel(R) SDVO Interface Timings Symbol Parameter Min Max Unit Figures Notes Transmitter and Receiver Timings UI Unit Interval 369.89 1000 ps TTX-EYE Minimum Transmission Eye Width 0.7 -- UI TTX-RISE/Fall D+/D- TX Out put Rise/Fall time -- 0.125 UI 0.40 -- UI TRX-EYE Minimum Receiver Eye Width 5 8-29 1,2 1,2 8-30 3,4 Notes: 1. Specified at the measurement point into a timing and voltage compliance test load and measured over any 250 consecutive TX UIs. (Also refer to the Transmitter compliance eye diagram) 2. A TTX-EYE = 0.70 UI provides for a total sum of deterministic and random jitter budget of TTXJITTER-MAX = 0.30 UI for the Transmitter collected over any 250 consecutive TX UIs. The TTXEYE-MEDIAN-to-MAX-JITTER specification ensures a jitter distribution in which the median and the maximum deviation from the median is less than half of the total TX jitter budget collected over any 250 consecutive TX UIs. It should be noted that the median is not the same as the mean. The jitter median describes the point in time where the number of jitter points on either side is approximately equal as opposed to the averaged time value. 3. Specified at the measurement point and measured over any 250 consecutive UIs. The test load documented in the PCI Express* specification 2.0 should be used as the RX device when taking measurements (also refer to the Receiver compliance eye diagram). If the clocks to the RX and TX are not derived from the same reference clock, the TX UI recovered from 3500 consecutive UI must be used as a reference for the eye diagram. 4. A TRX-EYE = 0.40 UI provides for a total sum of 0.60 UI deterministic and random jitter budget for the Transmitter and interconnect collected any 250 consecutive UIs. The TRX-EYE-MEDIAN-to--MAX-JITTER specification ensures a jitter distribution in which the median and the maximum deviation from the median is less than half of the total 0.6 UI jitter budget collected over any 250 consecutive TX UIs. It should be noted that the median is not the same as the mean. The jitter median describes the point in time where the number of jitter points on either side is approximately equal as opposed to the averaged time value. If the clocks to the RX and TX are not derived from the same reference clock, the TX UI recovered from 3500 consecutive UI must be used as the reference for the eye diagram. 5. Nominal Unit Interval for highest Intel SDVO speed is 370 ps. However, depending on the resolution on the interface, the UI may be more than 370 ps. Datasheet 289 Electrical Characteristics Table 8-15. DisplayPort* Interface Timings (DDP[D:B][3:0]) Symbol Parameter Min Nom Max Unit UI_High_Rate Unit Interval for High Bit Rate (2.7 Gbps/ lane) 370 -- -- ps UI_Low_Rate Unit Interval for Reduced Bit Rate (1.62 Gbps/lane) 617 -- -- ps 0 -- 0.5 % 33 kHz Down_Spread_A mplitude Link clock down spreading Down_Spread_Fr equency Link clock down-spreading frequency 30 -- Ltx-skew-intrapair Lane Intra-pair output skew at Tx package pins -- 20 Ttx-rise/ fall_mismatch_chi pdiff Lane Intra-pair Rise/Fall time mismatch at Tx package pin 5 % -- ps VTX-DIFFp-p-level1 Differential Peak-to-peak Output Voltage level 1 0.34 0.4 0.46 V VTX-DIFFp-p-level2 Differential Peak-to-peak Output Voltage level 2 0.51 0.6 0.68 V VTX-DIFFp-p-level3 Differential Peak-to-peak Output Voltage level 3 0.69 0.8 0.92 V VTX-preemp_ratio No Pre-emphasis 0 0 0 dB VTX-preemp_ratio 3.5 dB Pre-emphasis Level 2.8 3.5 4.2 dB VTX-preemp_ratio 6.0 dB Pre-emphasis Level 4.8 6 7.2 dB -- -- 2 UI Min Nom Max Unit 0.4 0.5 0.6 s ns Lane-to-Lane Output Skew at Tx package pins LTX-SKEWINTER_PAIR Table 8-16. DisplayPort* Aux Interface Symbol Parameter UI Aux unit interval T-Aux_bus_park Tcycle-to-cycle jitter 10 -- -- Maximum allowable UI variation within a single transaction at the connector pins of a transmitting device AUX CH bus park time 0.04 UI -- Maximum allowable UI variation within a single transaction at the connector pins of a receiving device 0.05 UI -- Table 8-17. DDC Characteristics - DDC Signals: VGA_DDC_CLK, VGA_DDC_DATA, DDP[D:B] _CTRLCLK, DDP[D:B]_CTRLDATA Symbol Fscl Parameter Standard Mode Fast Mode 1 MHz Units Max Min Max Min Max Operating Frequency 100 0 400 0 1000 kHz 1 1000 20 + 0.1Cb 300 -- 120 ns 2 300 -- 120 ns Tr Rise Time Tf 1 Fall Time 300 20+0.1Cb Note: 1. Measurement Point for Rise and Fall time: VIL(min) - VIL(max) 2. Cb = total capacitance of one bus line in pF. If mixed with High-speed mode devices, faster fall times according to High-Speed mode Tr/Tf are allowed. 290 Datasheet Electrical Characteristics Table 8-18. CRT DAC AC Characteristics Parameter Min Nom Pixel Clock Frequency Max Units 400 Notes MHz R, G, B Video Rise Time 0.25 -- 1.25 ns 1, 2, 8 (10-90% of black-to-white transition, @ 400-MHz pixel clock) R, G, B Video Fall Time 0.25 -- 1.25 ns 1, 3, 8 (90-10% of white-to-black transition, @ 400-MHz pixel clock) Settling Time Video channel-to-channel output skew Overshoot/ Undershoot 0.75 ns 1, 4, 8 @ 400 MHz pixel clock 0.625 ns 1, 5, 8 @ 400 MHz pixel clock V 1, 6, 8 Full-scale voltage step of 0.7 V % 1, 7, 8 -0.084 -- Noise Injection Ratio +0.084 2.5 Notes: 1. Measured at each R, G, B termination according to the VESA* Test Procedure - Evaluation of Analog Display Graphics Subsystems Proposal (Version 1, Draft 4, December 1, 2000). 2. R, G, B Max Video Rise/Fall Time: 50% of minimum pixel clock period. 3. R, G, B Min Video Rise/Fall Time: 10% of minimum pixel clock period. 4. Max settling time: 30% of minimum pixel clock period. 5. Video channel-channel output skew: 25% of minimum pixel clock period. 6. Overshoot/undershoot: 12% of black-white video level (full-scale) step function. 7. Noise injection ratio: 2.5% of maximum luminance voltage (DC to maximum pixel frequency). 8. R, G, B AC parameters are strongly dependent on the board implementation Table 8-19. Clock Timings (Sheet 1 of 4) Sym Parameter Min Max Unit Notes Figure PCI Clock (CLKOUT_PCI[4:0]) t1 Period 29.566 30.584 ns 8-12 t2 High Time 10.826 17.850 ns 8-12 t3 Low Time 10.426 17.651 ns 8-12 Duty Cycle 40 60 % t4 Rising Edge Rate 1.0 4 V/ns t5 Falling Edge Rate 1.0 4 V/ns -- 500 ps Jitter 8-12 8-12 8,9 14.318 MHz Flex Clock t6 Period 68.83 70.84 ns 8-12 t7 High Time 29.55 39.00 ns 8-12 t8 Low Time 29.16 38.80 ns 8-12 Duty Cycle 40 60 % Rising Edge Rate 1.0 4 V/ns Falling Edge Rate 1.0 4 V/ns 5 Jitter (14.318 MHz configured on CLKOUTFLEX1 or CLKOUTFLEX3) -- 800 ps 8,9 Jitter(14.318 MHz configured on CLKOUTFLEX0 or CLKOUTFLEX2) -- 1000 ps 8,9 5 48 MHz Flex Clock t9 Datasheet 20.32 21.34 ns 8-12 t10 High Time Period 7.02 12.51 ns 8-12 t11 Low Time 6.63 12.30 ns 8-12 291 Electrical Characteristics Table 8-19. Clock Timings (Sheet 2 of 4) Sym Min Max Unit Duty Cycle Parameter 40 60 % Notes Figure Rising Edge Rate 1.0 4 V/ns Falling Edge Rate 1.0 4 V/ns 5 Jitter (48MHz configured on CLKOUTFLEX1 or CLKOUTFLEX3) -- 410 ps 8,9 Jitter(48MHz configured on CLKOUTFLEX0 or CLKOUTFLEX2) -- 510 ps 8,9 ns 8-12 5 24 MHz Flex Clock t12 Period 41.16 42.18 t13 High Time 22.64 23.19 ns 8-12 t14 Low Time 18.52 18.98 ns 8-12 Duty Cycle 45 55 % Rising Edge Rate 1.0 4 V/ns Falling Edge Rate 5 1.0 4 V/ns 5 Jitter (24MHz configured on CLKOUTFLEX1 or CLKOUTFLEX3) -- 330 ps 8,9 Jitter(24MHz configured on CLKOUTFLEX0 or CLKOUTFLEX2) -- 510 ps 8,9 25 MHz Flex Clock t51 Period 39.84 40.18 ns 8-12 t52 High Time 16.77 21.78 ns 8-12 Low Time 8-12 t53 16.37 21.58 ns Duty Cycle 45 55 % Rising Edge Rate 1.0 4 V/ns 5 Falling Edge Rate 1.0 4 V/ns 5 -- -- ps 16 Jitter (25 MHz configured on CLKOUTFLEX2) 27 MHz Flex Clock t15 Period 36.4 37.67 ns 8-12 t16 High Time 20.02 20.72 ns 8-12 t17 Low Time 16.38 16.95 ns 8-12 Duty Cycle 45 55 % Rising Edge Rate 1.0 4 V/ns Falling Edge Rate 1.0 4 V/ns 5 Jitter (27MHz configured on CLKOUTFLEX1 or CLKOUTFLEX3) -- 450 ps 8,9 Jitter (27MHz configured on CLKOUTFLEX0 or CLKOUTFLEX2) -- 630 ps 8,9 5 CLKOUT_DP_[P,N] Period Period SSC On 7.108 7.756 ns 8-31 7.108 7.704 ns 8-31 40 60 % 8-31 Period Period SSC Off DtyCyc Duty Cycle V_Swing Differential Output Swing 300 -- mV 8-31 Rising Edge Rate 1.5 4 V/ns 8-31 Falling Edge Rate 1.5 4 V/ns 150 ps Slew_rise Slew_fall Jitter 292 8-31 8,9 Datasheet Electrical Characteristics Table 8-19. Clock Timings (Sheet 3 of 4) Sym Parameter Min Max Unit Notes Figure CLKOUT_PCIE[7:0]_[P,N], CLKOUT_DMI_[P,N], CLKOUT_PEG_[B:A]_[P,N], CLKOUT_ITPXDP_[P,N] Period Period SSC On 9.849 10.201 ns 8-31 Period Period SSC Off 9.849 10.151 ns 8-31 DtyCyc Duty Cycle 40 60 % 8-31 V_Swing Differential Output Swing 300 -- mV 8-31 Slew_rise Rising Edge Rate 1.5 4 V/ns 8-31 Slew_fall Falling Edge Rate 1.5 4 V/ns Jitter -- 150 ps 8,9,10 SSC Spread Spectrum 0 0.5 % 13,14 fsmb Operating Frequency 10 100 KHz t18 High time 4.0 50 s t19 Low time 4.7 -- s 8-21 t20 Rise time -- 1000 ns 8-21 t21 Fall time -- 300 ns 8-21 8-31 SMBus/SMLink Clock (SMBCLK, SML[1:0]CLK) 2 8-21 SMLink0 Clock (SML0CLK) (See note 15) fsmb Operating Frequency 0 400 KHz t18_SMLFM High time 0.6 50 s t19_SMLFM Low time 1.3 -- s 2 8-21 8-21 t20_SMLFM Rise time -- 300 ns 8-21 t21_SMLFM Fall time -- 300 ns 8-21 SMLink0 Clock (SML0CLK) (See note 17) fsmb Operating Frequency 0 t18_SMLFMP High time 0.26 t19_SMLFMP Low time 0.5 t20_SMLFMP Rise time -- t21_SMLFMP Fall time -- HDA_BCLK fHDA (Intel(R) 1000 KHz s -- 2 8-21 s 8-21 120 ns 8-21 120 ns 8-21 High Definition Audio) Operating Frequency 24.0 MHz Frequency Tolerance -- 100 ppm t26a Input Jitter (refer to Clock Chip Specification) -- 300 ppm t27a High Time (Measured at 0.75 Vcc) 18.75 22.91 ns 8-12 t28a Low Time (Measured at 0.35 Vcc) 18.75 22.91 ns 8-12 Suspend Clock (SUSCLK) fsusclk Operating Frequency 32 kHz 4 t39 High Time 9.5 -- s 4 t39a Low Time 9.5 -- s 4 XTAL25_IN/XTAL25_OUT Datasheet ppm12 CrystalTolerance cut accuracy max 35ppm(@ 25 C 3C) ppm12 TempStability max 30ppm(10 C to 70C) ppm12 Aging Max 5ppm 293 Electrical Characteristics Table 8-19. Clock Timings (Sheet 4 of 4) Sym Parameter Min Max Unit Notes Figure Slew_Rise Output Rise Slew Rate (0.2Vcc 0.6Vcc) 1 4 V/ns 11 8-32 Slew_Fall Output Fall Slew Rate (0.6Vcc 0.2Vcc) 1 4 V/ns 11 8-32 SPI_CLK Notes: 1. The CLK48 expects a 40/60% duty cycle. 2. The maximum high time (t18 Max) provide a simple ensured method for devices to detect bus idle conditions. 3. BCLK Rise and Fall times are measured from 10%VDD and 90%VDD. 4. SUSCLK duty cycle can range from 30% minimum to 70% maximum. 5. Edge rates in a system as measured from 0.8 V to 2.0 V. 6. The active frequency can be 5 MHz, 50 MHz, or 62.5 MHz depending on the interface speed. Dynamic changes of the normal operating frequency are not allowed. 7. Testing condition: 1 K pull-up to Vcc, 1 K pull-down and 10 pF pull-down and 1/2 inch trace (see Figure 8-32 for more detail). 8. Jitter is specified as cycle to cycle as measured between two rising edges of the clock being characterized. Period min and max includes cycle to cycle jitter and is also measured between two rising edges of the clock being characterized. 9. On all jitter measurements care should be taken to set the zero crossing voltage (for rising edge) of the clock to be the point where the edge rate is the fastest. Using a Math function = Average(Derivavitive(Ch1)) and set the averages to 64, place the cursors where the slope is the highest on the rising edge - usually this lower half of the rising edge. The reason this is defined is for users trying to measure in a system it is impossible to get the probe exactly at the end of the Transmission line with large Flip Chip components, this results in a reflection induced ledge in the middle of the rising edge and will significantly increase measured jitter. 10. Phase jitter requirement: The designated Gen2 outputs will meet the reference clock jitter requirements from the PCI Express* Gen2 Base Specification. The test is to be performed on a component test board under quiet conditions with all clock outputs on. Jitter analysis is performed using a standardized tool provided by the PCI SIG. Measurement methodology is defined in Intel document "PCI Express Reference Clock Jitter Measurements". This is not for CLKOUT_PCIE[7:0]. 11. Testing condition: 1-k pull-up to Vcc, 1 k pull-down and 10 pF pull-down and 1/2 inch trace (see Figure 8-32 for more detail). 12. Total of crystal cut accuracy, frequency variations due to temperature, parasitics, load capacitance variations and aging is recommended to be less than 90 ppm. 13. Spread Spectrum (SSC) is referenced to rising edge of the clock. 14. Spread Spectrum (SSC) of 0.25% on CLKOUT_PCIE[7:0] and CLKOUT_PEG_[B:A] is used for WiMAX friendly clocking purposes. 15. When SMLink0 is configured to run in Fast Mode (FM) using a soft strap, the supported operating range is 0 Hz ~ 400 kHz, but the typical operating frequency is in the range of 300 kHz - 400 kHz. 16. The 25 MHz output option for CLKOUTFLEX2 is derived from the 25 MHz crystal input to the PCH. The PPM of the 25 MHz output is equivalent to that of the crystal. 17. When SMLink0 is configured to run in Fast Mode Plus (FMP) using a soft strap, the supported operating range is 0 Hz ~ 1 MHz, but the typical operating frequency is in the range of 900 kHz - 1000 kHz. This is the default mode for this interface. Table 8-20. Universal Serial Bus Timing (Sheet 1 of 2) Sym Parameter Min Max Units Notes Fig Full-speed Source (Note 7) 294 t100 USBPx+, USBPx- Driver Rise Time 4 20 ns 1, 6 CL = 50 pF 8-18 t101 USBPx+, USBPx- Driver Fall Time 4 20 ns 1, 6 CL = 50 pF 8-18 2, 3 8-19 t102 Source Differential Driver Jitter - To Next Transition - For Paired Transitions -3.5 -4 3.5 4 t103 Source SE0 interval of EOP 160 175 ns 4 8-20 t104 Source Jitter for Differential Transition to SE0 Transition -2 5 ns 5 ns ns Datasheet Electrical Characteristics Table 8-20. Universal Serial Bus Timing (Sheet 2 of 2) Sym Parameter Min Max Units Notes Fig 3 8-19 4 8-20 Full-speed Source (Note 7) t105 Receiver Data Jitter Tolerance - To Next Transition - For Paired Transitions t106 t107 -18.5 -9 18.5 9 ns ns EOP Width: Must accept as EOP 82 -- ns Width of SE0 interval during differential transition -- 14 ns Low-speed Source (Note 8) USBPx+, USBPx - Driver Rise Time 75 300 ns 6 CL = 200 pF CL =600 pF 8-18 USBPx+, USBPx - Driver Fall Time 75 300 ns 6 CL = 200 pF CL =600 pF 8-18 Source Differential Driver Jitter To Next Transition For Paired Transitions 2, 3 8-19 -25 -14 25 14 ns ns t111 Source SE0 interval of EOP 1.25 1.50 s 4 8-20 t112 Source Jitter for Differential Transition to SE0 Transition -40 100 ns 5 t113 Receiver Data Jitter Tolerance - To Next Transition - For Paired Transitions -152 -200 152 200 ns ns t114 EOP Width: Must accept as EOP 670 -- ns t115 Width of SE0 interval during differential transition -- 210 ns t108 t109 t110 3 8-19 4 8-20 Notes: 1. Driver output resistance under steady state drive is specified at 28 at minimum and 43 at maximum. 2. Timing difference between the differential data signals. 3. Measured at crossover point of differential data signals. 4. Measured at 50% swing point of data signals. 5. Measured from last crossover point to 50% swing point of data line at leading edge of EOP. 6. Measured from 10% to 90% of the data signal. 7. Full-speed Data Rate has minimum of 11.97 Mb/s and maximum of 12.03 Mb/s. 8. Low-speed Data Rate has a minimum of 1.48 Mb/s and a maximum of 1.52 Mb/s. Table 8-21. SATA Interface Timings (Sheet 1 of 2) Sym UI UI-2 UI-3 Min Max Units Gen I Operating Data Period 666.43 670.23 ps Gen II Operating Data Period (3Gb/s) 333.21 335.11 ps Gen III Operating Data Period (6Gb/s) Notes 166.6083 166.6667 ps t120gen1 Rise Time 0.15 0.41 UI 1 t121gen1 Fall Time 0.15 0.41 UI 2 t120gen2 Rise Time 0.2 0.41 UI 1 t121gen2 Fall Time 0.2 0.41 UI 2 t120gen3 Rise Time 0.2 0.48 UI 1 t121gen3 Fall Time 0.2 0.48 UI 2 -- 20 ps t122 Datasheet Parameter TX differential skew Figure 295 Electrical Characteristics Table 8-21. SATA Interface Timings (Sheet 2 of 2) Sym Parameter Min Max Units Notes t123 COMRESET 304 336 ns 3 t124 COMWAKE transmit spacing 101.3 112 ns 3 t125 OOB Operating Data period 646.67 686.67 ns 4 Figure Notes: 1. 20% - 80% at transmitter 2. 80% - 20% at transmitter 3. As measured from 100 mV differential crosspoints of last and first edges of burst. 4. Operating data period during Out-Of-Band burst transmissions. Table 8-22. SMBus and SMLink Timing Sym Parameter Min Max Units Notes Fig t130 Bus Free Time Between Stop and Start Condition 4.7 -- s 8-21 t130SMLFM Bus Free Time Between Stop and Start Condition 1.3 -- s 5 8-21 t130SMLFMP Bus Free Time Between Stop and Start Condition 0.5 -- s 5 8-21 t131 Hold Time after (repeated) Start Condition. After this period, the first clock is generated. 4.0 -- s t131SMLFM Hold Time after (repeated) Start Condition. After this period, the first clock is generated. 0.6 -- s 5 8-21 t131SMLFMP Hold Time after (repeated) Start Condition. After this period, the first clock is generated. 0.26 -- s 5 8-21 8-21 t132 Repeated Start Condition Setup Time 4.7 -- s t132SMLFM Repeated Start Condition Setup Time 0.6 -- s 5 Repeated Start Condition Setup Time 0.26 -- s 5 4.0 -- s t132SMLFMP t133 Stop Condition Setup Time 8-21 8-21 8-21 8-21 t133SMLFM Stop Condition Setup Time 0.6 -- s 5 8-21 t133SMLFMP Stop Condition Setup Time 0.26 -- s 5 8-21 t134 Data Hold Time 300 -- ns 4 8-21 t134SMLFM Data Hold Time 0 -- ns 4, 5 8-21 4, 5 t134SMLFMP 0 -- ns Data Setup Time 250 -- ns t135SMLFM Data Setup Time 100 -- ns 5 8-21 t135SMLFMP Data Setup Time 50 -- ns 5 8-21 t136 Device Time Out 25 35 ms 1 t137 Cumulative Clock Low Extend Time (slave device) -- 25 ms 2 8-22 t138 Cumulative Clock Low Extend Time (master device) -- 10 ms 3 8-22 t135 Data Hold Time 8-21 8-21 Notes: 1. A device will timeout when any clock low exceeds this value. 2. t137 is the cumulative time a slave device is allowed to extend the clock cycles in one message from the initial start to stop. If a slave device exceeds this time, it is expected to release both its clock and data lines and reset itself. 296 Datasheet Electrical Characteristics 3. 4. 5. t138 is the cumulative time a master device is allowed to extend its clock cycles within each byte of a message as defined from start-to-ack, ack-to-ack or ack-to-stop. t134 has a minimum timing for I2C of 0 ns, while the minimum timing for SMBus/SMLINK is 300 ns. Timings with the SMLFM designator apply only to SMLink0 and only when SMLink0 is operating in Fast Mode. Table 8-23. Intel(R) High Definition Audio (Intel(R) HD Audio) Timing Sym Min Max Units t143 Time duration for which HDA_SD is valid before HDA_BCLK edge. Parameter 7 -- ns Notes 8-24 Fig t144 Time duration for which HDA_SDO is valid after HDA_BCLK edge. 7 -- ns 8-24 t145 Setup time for HDA_SDI[3:0] at rising edge of HDA_BCLK 15 -- ns 8-24 t146 Hold time for HDA_SDI[3:0] at rising edge of HDA_BCLK 0 -- ns 8-24 Min Max Units Table 8-24. LPC Timing Sym Parameter Notes Fig t150 LAD[3:0] Valid Delay from PCICLK Rising 2 11 ns 8-13 t151 LAD[3:0] Output Enable Delay from PCICLK Rising 2 -- ns 8-17 t152 LAD[3:0] Float Delay from PCICLK Rising -- 28 ns 8-15 t153 LAD[3:0] Setup Time to PCICLK Rising 7 -- ns 8-14 t154 LAD[3:0] Hold Time from PCICLK Rising 0 -- ns 8-14 t155 LDRQ[1:0]# Setup Time to PCICLK Rising 12 -- ns 8-14 t156 LDRQ[1:0]# Hold Time from PCICLK Rising 0 -- ns 8-14 t157 eE# Valid Delay from PCICLK Rising 2 12 ns 8-13 Min Max Units 7 -- ns 8-14 Table 8-25. Miscellaneous Timings Sym t160 Parameter SERIRQ Setup Time to PCICLK Rising Notes Fig t161 SERIRQ Hold Time from PCICLK Rising 0 -- ns 8-14 t162 RI#, GPIO, USB Resume Pulse Width 2 -- RTCCLK 8-16 t163 SPKR Valid Delay from OSC Rising -- 200 ns 8-13 t164 SERR# Active to NMI Active -- 200 ns Min Max Units Notes 1 Table 8-26. SPI Timings (20 MHz) (Sheet 1 of 2) Sym Datasheet Parameter Fig t180a Serial Clock Frequency - 20 MHz Operation 17.2 18.73 MHz t183a Tco of SPI_MOSI and SPI_IO[2:3] with respect to serial clock falling edge at the host -5 13 ns 8-23 t184a Setup of SPI_MISO and SPI_IO[2:3] with respect to serial clock falling edge at the host 16 -- ns 8-23 t185a Hold of SPI_MISO and SPI_IO[2:3] with respect to serial clock falling edge at the host 0 -- ns 8-23 t186a Setup of SPI_CS[1:0]# assertion with respect to serial clock rising at the host 30 -- ns 8-23 t187a Hold of SPI_CS[1:0]# de-assertion with respect to serial clock falling at the host 30 -- ns 8-23 t188a SPI_CLK High Time 26.37 -- ns 8-23 297 Electrical Characteristics Table 8-26. SPI Timings (20 MHz) (Sheet 2 of 2) Sym t189a Parameter SPI_CLK Low Time Min Max Units 26.82 -- ns Notes Fig 8-23 Notes: 1. The typical clock frequency driven by the PCH is 17.86 MHz. 2. Measurement point for low time and high time is taken at 0.5(VccSPI). Table 8-27. SPI Timings (33 MHz) Sym Parameter Min Max Units Notes 29.83 33.81 MHz 1 Tco of SPI_MOSI and SPI_IO[2:3] with respect to serial clock falling edge at the host -5 5 ns 8-23 t184b Setup of SPI_MISO and SPI_IO[2:3] with respect to serial clock falling edge at the host 8 -- ns 8-23 t185b Hold of SPI_MISO and SPI_IO[2:3] with respect to serial clock falling edge at the host 0 -- ns 8-23 t186b Setup of SPI_CS[1:0]# assertion with respect to serial clock rising at the host 30 -- ns 8-23 t187b Hold of SPI_CS[1:0]# de-assertion with respect to serial clock falling at the host 30 -- ns 8-23 t180b Serial Clock Frequency - 33 MHz Operation t183b Fig t188b SPI_CLK High Time 14.88 - ns 8-23 t189b SPI_CLK Low Time 15.18 - ns 8-23 Notes: 1. The typical clock frequency driven by the PCH is 33 MHz. 2. Measurement point for low time and high time is taken at 0.5(VccSPI). Table 8-28. SPI Timings (50 MHz) Sym Parameter Min Max Units Notes 46.99 53.40 MHz 1 Tco of SPI_MOSI and SPI_IO[2:3] with respect to serial clock falling edge at the host -3 3 ns 8-23 t184c Setup of SPI_MISO and SPI_IO[2:3] with respect to serial clock falling edge at the host 8 -- ns 8-23 t185c Hold of SPI_MISO and SPI_IO[2:3] with respect to serial clock falling edge at the host 0 -- ns 8-23 t186c Setup of SPI_CS[1:0]# assertion with respect to serial clock rising edge at the host 30 -- ns 8-23 t187c Hold of SPI_CS[1:0]# assertion with respect to serial clock rising edge at the host 30 -- ns 8-23 t180c Serial Clock Frequency - 50 MHz Operation t183c Fig t188c SPI_CLK High Time 7.1 -- ns 2, 3 8-23 t189c SPI_CLK Low Time 11.17 -- ns 2, 3 8-23 Note: 1. Typical clock frequency driven by the PCH is 50 MHz. 2. When using 50 MHz mode ensure target flash component can meet t188c and t189c specifications. Measurement should be taken at a point as close as possible to the package pin. 3. Measurement point for low time and high time is taken at 0.5(VccSPI). Table 8-29. SST Timings (Server/Workstation Only) (Sheet 1 of 2) Sym tBIT 298 Parameter Bit time (overall time evident on SST) Bit time driven by an originator Min Max Units Notes Fig 0.495 0.495 500 250 s s 1 - Datasheet Electrical Characteristics Table 8-29. SST Timings (Server/Workstation Only) (Sheet 2 of 2) Sym Parameter Min Max Units tBIT,jitter Bit time jitter between adjacent bits in an SST message header or data bytes after timing has been negotiated -- -- % tBIT,drift Change in bit time across a SST address or SST message bits as driven by the originator. This limit only applies across tBIT-A bit drift and tBIT-M drift. -- -- % tH1 High level time for logic '1' 0.6 0.8 x tBIT tH0 High level time for logic '0' 0.2 0.4 x tBIT tSSTR Rise time (measured from VOL = 0.3V to VIH,min) -- 25 + 5 ns/ node tSSTF Fall time (measured from VOH = 1.1V to VIL,max) -- 33 ns/ node Notes Fig 2 Notes: 1. The originator must drive a more restrictive time to allow for quantized sampling errors by a client yet still attain the minimum time less than 500 s. tBIT limits apply equally to tBIT-A and tBIT-M. PCH is targeted on 1 Mbps which is 1 s bit time. 2. The minimum and maximum bit times are relative to tBIT defined in the Timing Negotiation pulse. 3. tBIT-A is the negotiated address bit time and tBIT-M is the negotiated message bit time. Table 8-30. Controller Link Receive Timings Sym Parameter Min Max Units Notes t190 Single bit time 13 -- ns t191 Single clock period 15 -- ns t192 Rise time/Fall time 0.11 3.5 V/ns t193 Setup time before CL_CLK 0.9 -- ns 0.9 -- ns CL_Vref - 0.08 V 2 V 2 t194 Hold time after CL_CLK VIL_AC Input low voltage (AC) VIH_AC Input high voltage (AC) CL_Vref +0.08 Fig 8-33 8-33 1 8-34 8-33 8-33 Notes: 1. Measured from (CL_Vref - 50 mV to CL_Vref + 50 mV) at the receiving device side. No test load is required for this measurement as the receiving device fulfills this purpose. 2. CL_Vref = 0.12*(VccSus3_3). Table 8-31. USB 3.0 Interface Transmit and Receiver Timings Sym UI TTX-EYE 8.7 Parameter Unit Interval - USB 3.0 (5.0 GT/s) Minimum Transmission Eye Width Min Max Units 199.94 200.06 ps 0.625 -- UI Notes Fig Power Sequencing and Reset Signal Timings Table 8-32. Power Sequencing and Reset Signal Timings (Sheet 1 of 3) Sym t200 t200a Datasheet Parameter Min Max Units Notes Fig VccRTC active to RTCRST# de-assertion 9 -- ms 26 8-1, 8-2 RTCRST# de-assertion to DPWROK high 1 -- us 8-1, 8-2 299 Electrical Characteristics Table 8-32. Power Sequencing and Reset Signal Timings (Sheet 2 of 3) Sym t200b t200c t201 t202 t202a t203 t204 t205a t205b t206 Min Max Units 10 -- ms 8-1, 8-2 VccDSW3_3 active to VccSus3_3 active 0 -- ms 8-1, 8-2 VccSUS active to RSMRST# de-assertion 10 -- ms 1 8-1, 8-2 DPWROK high to SLP_SUS# de-assertion 95 -- ms 2, 3 8-1, 8-2 RSMRST# and SLP_SUS# de-assertion to SUSCLK toggling 5 -- ms 3, 4 8-1, 8-2 s 5, 29 8-3 8-3 VccDSW3_3 active to DPWROK high SLP_S5# high to SLP_S4# high 30 SLP_S4# high to SLP_S3# high 30 Vcc active to PWROK high PWROK high to PLTRST# de-assertion PWROK deglitch time 5 -- 99 1 -- Notes s 6 ms 7, 13 ms 24 ms 8 Fig t207 VccASW active to APWROK high 1 -- ms t208 PWROK high to PCH clock outputs stable 1 -- ms t209 PCH clock output stable to PROCPWRGD high 1 -- ms t210 PROCPWRGD and SYS_PWROK high to SUS_STAT# de-assertion 1 -- ms t211 SUS_STAT# de-assertion to PLTRST# deassertion 60 -- s t212 APWROK high to SPI Soft Strap Reads 500 -- s 22 t213 APWROK high to CL_RST# de-asserted 500 -- s 10 t214 DMI message and all PCI Express ports and DMI in L2/L3 state to SUS_STAT# active 60 -- s 8-6 t215 SUS_STAT# active to PLTRST# active 210 -- s 8-6 t217 PLTRST# active to PROCPWRGD inactive 30 -- s 8-6 t218 PROCPWRGD inactive to clocks invalid 10 -- s 8-6 t219 Clocks invalid to SLP_S3# assertion 1 -- s 8-6 t220 SLP_S3# low to SLP_S4# low 30 -- s 8-6 t221 SLP_S4# low to SLP_S5# low 30 -- s 8-6 t222 SLP_S3# active to PWROK de-asserted 0 -- t223 PWROK rising to DRAMPWROK rising 0 -- t224 DRAMPWROK falling to SLP_S4# falling -100 -- ns 11, 23 8-8 t225 VccRTC active to VccDSW3_3 active 0 -- ms 1, 12 8-2 t227 VccSus active to VccASW active 0 -- ms 1 t229 VccASW active to Vcc active 0 -- ms t230 t231 t232 t233 300 Parameter APWROK high to PWROK high 9 8-6 s 8-8 0 -- ms PWROK low to Vcc falling 40 -- ns 13, 15, 16, 27, 28 APWROK falling to VccASW falling 40 -- ns 15, 16, 27, 28 5 -- s 13, 14 SLP_S3# assertion to Vcc rail falling Datasheet Electrical Characteristics Table 8-32. Power Sequencing and Reset Signal Timings (Sheet 3 of 3) Sym t234 t235 Parameter Min DPWROK falling to VccDSW3_3 rail falling 40 RSMRST# assertion to VccSUS rail falling 40 Max Units Notes Fig ns 15, 16, 27, 28 8-7 -- ns 1, 15, 16, 27, 28 8-7 t236 RTCRST# de-assertion to VccRTC rail falling 0 -- ms t237 SLP_LAN# (or LANPHYPC) rising to Intel LAN Phy power high and stable -- 20 ms t238 DPWROK falling to any of VccDSW3_3, VccSUS, VccASW, or Vcc falling 70 -- ns 1, 13, 15, 16, 27, 28 t241 VccSus supplies active to Vcc supplies active 0 -- ms 1, 13 t244 VccSus active to SLP_S5#, SLP_S4#, SLP_S3#, SUS_STAT#, PLTRST# and PCIRST# valid -- 50 ns 21 t246 S4 Wake Event to SLP_S4# inactive (S4 Wake) See Note Below 5 t247 S3 Wake Event to SLP_S3# inactive (S3 Wake) See Note Below 6 t251 RSMRST# de-assertion to APWROK assertion 0 -- ms t252 THRMTRIP# active to SLP_S3#, SLP_S4#, SLP_S5# active -- 175 ns t253 RSMRST# rising edge transition from 20% to 80% -- 50 s t254 RSMRST# falling edge transition -- 50 s t255 DPWROK rising edge transition from 20% to 80% -- 50 s -- 50 s 19, 20 4-5 -- sec 25 t256 DPWROK falling edge transition t257 Power cycle duration for a global reset other than G3 or Deep Sx. Also the duration of a host reset with power cycle. 8-7 18, 19 Notes: 1. VccSus supplies include VccSus3_3 and VccSusHDA. Also includes DcpSus for mobile platforms that power DcpSus externally. 2. This timing is a nominal value counted using RTC clock. If RTC clock isn't already stable at the rising edge of RSMRST#, this timing could be shorter or longer than the specified value. 3. Platforms not supporting Deep Sx will typically have SLP_SUS# left as no connect. Hence DPWROK high and RSMRST# de-assertion to SUSCLK toggling would be t202+t202a=100 ms minimum. 4. Platforms supporting Deep Sx will have SLP_SUS# de-assert prior to RSMRST#. Platforms not supporting Deep Sx will have RSMRST# de-assert prior to SLP_SUS#. 5. Dependency on SLP_S4# and SLP_A# stretching 6. Dependency on SLP_S3# and SLP_A# stretching 7. It is required that the power rails associated with PCI/PCIe (typically the 3.3 V, 5 V, and 12 V core well rails) have been valid for 99 ms after PWROK assertion in order to comply with the 100 ms PCI/PCIe 2.0 specification on PLTRST# de-assertion. System designers must ensure the requirement is met on the platforms. 8. Ensure PWROK is a solid logic '1' before proceeding with the boot sequence. Note: If PWROK drops after t206, it will be considered a power failure. 9. Timing is dependant on whether 25 MHz crystal is stable by the time PWROK is high. 10. Requires SPI messaging to be completed. 11. The negative min timing implies that DRAMPWROK must either fall before SLP_S4# or within 100 ns after it. 12. The VccDSW3_3 supplies must never be active while the VccRTC supply is inactive. 13. Vcc includes VccIO, Vcc, Vcc3_3, VccADAC1_5, VccADACBG3_3, V_PROC_IO, VccCLK, VccCLK3_3, VccVRM, and VccASW (if Intel ME only powered in S0). 14. A Power rail is considered to be inactive when the rail is at its nominal voltage minus 5% or less. 15. Board design may meet (t231 AND t232 AND t234 AND t235) OR (t238). Datasheet 301 Electrical Characteristics 16. The definition of rail falling for this timing requirement is as follows: 1) VCCDSW3_3 and VCCSUS3_3 is 2.9V; 2) VCCASW and DCPSUS* (in external suspend VR mode) is 0.92V; 3) VCC is 0.99V. 17. If RTC clock is not already stable at RSMRST# rising edge, this time may be longer. 18. RSMRST# falling edge must transition to 0.8 V or less before VccSus3_3 drops to 2.9V 19. The 50 s should be measured from Vih to Vil (2 V to 0.78V). 20. DPWROK falling edge must transition to 0.8V or less before VccDSW3_3 drops to 2.9V 21. This is an internal timing showing when the signals (SLP_S5#, SLP_S4#, SLP_S3#, SUS_STAT#, PLTRST# and PCIRST#) are valid after VccSus rail is Active. 22. APWROK high to SPI Soft Strap Read is an internal PCH timing. The timing cannot be measured externally and included here for general power sequencing reference. 23. If Deep Sx was entered from S3. SLP_S4# will remain high while DRAMPWROK is undriven. 24. Timing enabled through soft strap. If T205b is not enabled, the platform is responsible for controlling the assertion timing of PWROK and SYS_PWROK in such a way that it satisfies the PCIe timing requirement of power stable to reset de-assertion. 25. Programmable using PM_CFG.PWR_CYC_DUR. Default is 4-5 seconds. 26. Measured from VCCRTC-10% to RTCRST# reaching 0.55*VCCRTC. VCCRTC is defined as the final settling voltage that the rail ramps. 27. Requirement applies to power failure and surprise power down scenario. 28. Ensure respective PWROK signals (PCH_PWROK, APWROK and RSMRST#) toggle appropriately during normal power state transition (for example S0->Sx->S0, S0->Deep Sx->S0, and so on) even if the supply voltage does not drop below the specified value. Use of the stretch registers can be used to achieve this. 29. Timing does not apply after Deep Sx exit when Intel ME has configured SLP_S5# and/or SLP_S4# to rise with SLP_A#. 302 Datasheet Electrical Characteristics 8.8 Power Management Timing Diagrams Figure 8-1. G3 w/RTC Loss to S4/S5 (With Deep Sx Support) Timing Diagram S o u rc e D e s tin a tio n S ig n a l N a m e B o a rd PCH V ccR TC B o a rd PCH RTCRST# B o a rd PCH V ccD S W 3_3 B o a rd PCH DPW ROK PCH B o a rd SLP_SUS# B o a rd PCH VccSus B o a rd PCH RSM RST# G3 D e e p S 4 /S 5 S 5 /S 4 t2 2 5 t2 0 0 t2 0 0 a t2 0 0 b t2 0 0 c t2 0 2 t2 0 1 PCH B o a rd S U S C LK PCH B o a rd S LP _S 5# t2 2 6 v a lid t2 0 2 a O n ly fo r S 4 a fte r G 3 o r D e e p S x Note: VCCSUS rail ramps up later in comparison to VCCDSW due to assumption that SLP_SUS# is used to control power to VCCSUS. Figure 8-2. G3 w/RTC Loss to S4/S5 (Without Deep Sx Support) Timing Diagram S o u rc e D e s tin a tio n S ig n a l N a m e B o a rd PCH VccR TC B o a rd PCH RTCRST# B o a rd PCH V ccD S W 3_3 B o a rd PCH DPW ROK PCH B o a rd S LP_S U S# B o a rd PCH VccSus B o a rd PCH RSMRST# PCH B o a rd G3 S 5 /S 4 t2 2 5 t2 0 0 t2 0 0 a t2 0 0 b t2 0 0 c t2 0 2 t2 0 1 t2 2 6 S U SC LK v a lid t2 0 2 a PCH Datasheet B o a rd S LP_S 5# O n ly fo r S 4 a fte r G 3 303 Electrical Characteristics Figure 8-3. S5 to S0 Timing Diagram Source Dest Signal Name PCH Board SLP_S5# PCH Board SLP_S4# PCH Board SLP_S3# PCH Board SLP_A# PCH Board SLP_LAN# Board PCH VccASW Board PCH Vcc t203 t204 Could already be high before this sequence begins (to support M3), but will never go high later than SLP_S3# Could already be high before this sequence begins (to support WOL), but will never go high later than SLP_S3# or SLP_A# t229 PROCPWRGD CPU CPU VRM Board CPU VccCore_CPU CPU VRM PCH SYS_PWROK Board PCH PWROK Board PCH APWROK PCH CPU DRAMPWROK Serial VID Load CPU SVID V_vid t205 t206 t207 Board PCH PCH Board APWROK may come up earlier than PWROK, but no later t230 25 MHz Crystal Osc PCH Output Clocks PCH CPU PROCPWRGD PCH Board SUS_STAT# CPU PCH THRMTRIP# stable stable t208 t209 t210 Assumes soft strap programmed to start at PROCPWRGD - expected setting for SNB CPU/Board PLTRST# honored t211 CK Tr ain ST ing RA P_ SE CP T U Fl _R ex ES CP SK ET U_ U _ RE V DO SE DM N E T_ DO wr NE ite _A s PCH ignored PCH 304 CPU DMI Datasheet Electrical Characteristics Figure 8-4. S3/M3 to S0 Timing Diagram Source Dest Signal Name PCH Board SLP_S5# PCH Board SLP_S4# PCH Board SLP_S3# PCH Board SLP_A# PCH Board SLP_LAN# Board PCH Board PCH CPU CPU VRM Board CPU VccCore_CPU CPU VRM PCH SYS_PWROK Board PCH PWROK Board PCH APWROK PCH CPU DRAMPWROK VccASW Vcc PCH 25 MHz Crystal Osc PCH Board PCH Output Clocks PCH CPU PROCPWRGD Board PROCPWRGD Serial VID Load CPU SVID PCH Board SUS_STAT# CPU PCH THRMTRIP# PCH CPU/Board Note: V_PROC_IO may go to Vboot at this time, but can also stay at 0V (default) V_vid t205 t206 stable stable t208 t209 t210 Assumes soft strap programmed to start at PROCPWRGD ignored honored PLTRST# t211 Tr PCH Figure 8-5. CPU ai ni ng ST R A S P_ s E N ite CK O w r _A _ D M O NE ET V D _D E S K U SET _ R S _ RE P U ex U C Fl CP ET DMI S5/M-Off - S5/M3 Timing Diagram S o u rc e D est S ig n a l N a m e PCH B o a rd S L P _S 5# PCH B o a rd S L P _S 4# PCH B o a rd S L P _S 3# PCH B o a rd SLP_A# PCH B o a rd SLP_LAN# B o a rd PCH V ccA S W B o a rd PCH APW ROK C o u ld a lre ad y b e h ig h b e fo re this se qu e n ce be g in s (to su p po rt W O L), b ut w ill n e ve r g o hig h la te r th a n S L P_A # t2 07 t21 2 Datasheet PCH S P I F la sh PCH C o n tro lle r L in k SPI C L_R ST1# (M o b ile O n ly) t21 3 305 Electrical Characteristics Figure 8-6. S0 to S5 Timing Diagram Source Dest PCH PCIe* Devices PCH Board Signal Name DMI PCIe Ports SUS_STAT# L2/L3 DMI Message normal operation L2/L3 t214 t215 PCH Board PLTRST# PCH Board PROCPWRGD CPU PCH THRMTRIP# PCH Board PCH Output Clocks PCH Board SLP_S3# PCH Board SLP_S4# PCH Board SLP_S5# t217 honored ignored t218 valid t219 t220 t221 t222 Board PCH PWROK Board PCH SYS_PWROK PCH CPU DRAMPWROK PCH Controller Link PCH GbE PHY PCH Board Board PCH APWROK PCH Board SLP_LAN# May drop before or after SLP_S4/5# and DRAMPWRGD CL_RST1# ME-Related Signals Going to M3: stay high Going to MOFF: go low Only switch if going to MOFF 306 Source of LANPHYPC value SLP_A# Live value from GbE MAC Value from MAC latched in SUS well If appropriate, save MAC PMCSR context here SLP_LAN# could stay high for M3 or WOL Datasheet Electrical Characteristics Figure 8-7. S3/S4/S5 to Deep Sx to G3 w/ RTC Loss Timing Diagram S o u rc e D e s t in a t io n S ig n a l N a m e Deep Sx S 3 /S 4 /S 5 PCH B o a rd (E C ) B o a rd ( E C ) PCH G3 SUSW ARN# u n d r iv e n PCH SUSACK# u n d r iv e n B o a rd SLP_SUS# PCH B o a rd SLP_S3# / SLP_A# PCH B o a rd SLP_S 4# u n d r iv e n u n d r iv e n u n d r iv e n S L P _ S 4 # d ro p s h e re if n o t a lr e a d y a s s e rte d PCH B o a rd S LP_S 5# u n d r iv e n S L P _ S 5 # d ro p s h e re if n o t a lr e a d y a s s e rte d B o a rd PCH RSM RST# B o a rd PCH VccS us B o a rd PCH DPW ROK B o a rd PCH V ccD S W 3_3 B o a rd PCH RTCRST# B o a rd PCH V ccR T C t2 3 5 t2 3 4 t2 3 6 Figure 8-8. G3 to Deep Sx Timing Diagram Note: On a Deep Sx supported platform, platform must transition to Sx state upon G3 exit, prior to determining that conditions are met for a Deep Sx transition (G3->Sx->Deep Sx). S o u rc e D e s tin a tio n B o a rd PCH S ig n a l N a m e G3 V ccR TC Deep Sx S 5 /S 4 /S 3 Deep Sx t2 2 5 t2 0 0 B o a rd PCH RTCRST# B o a rd PCH V ccD S W 3_3 B o a rd PCH DPW ROK PCH B o a rd B o a rd PCH t2 0 0 a t2 0 0 b SUSW ARN# u n d riv e n u n d riv e n PCH SUSACK# u n d riv e n u n d riv e n B o a rd SLP_SU S# t2 0 2 t2 0 0 c B o a rd PCH V ccS us B o a rd PCH RSMRST# t2 0 1 t2 3 5 t2 2 6 t2 0 2 a Datasheet PCH B o a rd SUSC LK PCH B o a rd SLP _S5# u n d riv e n PCH B o a rd S LP_S4# u n d riv e n PCH B o a rd S LP_S3# u n d riv e n v a lid D e p e n d o n S x s ta te p rio r to e n try 307 Electrical Characteristics Figure 8-9. 8.9 DRAMPWROK Timing Diagram Source Destination Signal Name PCH Board SLP_S4# Board PCH PWROK PCH CPU DRAMPWROK t223 t224 AC Timing Diagrams Figure 8-10. Clock Cycle Time Figure 8-11. Transmitting Position (Data to Strobe) CLKA/ CLKB Tppos0 YA/YB Tppos1 Tppos2 Tppos3 Tppos4 Tppos5 Tppos6 308 Datasheet Electrical Characteristics Figure 8-12. Clock Timing Period High Time 2.0V 0.8V Low Time Fall Time Rise Time Figure 8-13. Valid Delay from Rising Clock Edge Clock 1.5V Valid Delay Output VT Figure 8-14. Setup and Hold Times Clock 1.5V Setup Time Input Hold Time VT VT Figure 8-15. Float Delay Input VT Float Delay Output Datasheet 309 Electrical Characteristics Figure 8-16. Pulse Width Pulse Width VT VT Figure 8-17. Output Enable Delay Clock 1.5V Output Enable Delay Output VT Figure 8-18. USB Rise and Fall Times Rise Time CL 90% Fall Time 90% Differential Data Lines 10% 10% CL tR tF Low-speed: 75 ns at CL = 50 pF, 300 ns at C L = 350 pF Full-speed: 4 to 20 ns at C L = 50 pF High-speed: 0.8 to 1.2 ns at C L = 10 pF 310 Datasheet Electrical Characteristics Figure 8-19. USB Jitter T period Crossover Points Differential Data Lines Jitter Consecutive Transitions Paired Transitions Figure 8-20. USB EOP Width Tperiod Data Crossover Level Differential Data Lines EOP Width Figure 8-21. SMBus / SMLink Transaction t19 t20 t21 SMBCLK t135 t131 t134 t133 t132 t18 SMBDATA t130 Note: Datasheet txx also refers to txx_SM, txxx also refers to txxxSMLFM, SMBCLK also refers to SML[1:0]CLK, and SMBDATA also refers to SML[1:0]DATA in Figure 8-21. 311 Electrical Characteristics Figure 8-22. SMBus / SMLink Timeout Start Stop t137 CLKack CLKack t138 t138 SMBCLK SMBDATA Note: SMBCLK also refers to SML[1:0]CLK and SMBDATA also refers to SML[1:0]DATA in Figure 8-22. Figure 8-23. SPI Timings t188 t189 SPI_CLK t183 SPI_MOSI t184 t185 SPI_MISO t186 t187 SPI_CS# 312 Datasheet Electrical Characteristics Figure 8-24. Intel(R) High Definition Audio (Intel(R) HD Audio) Input and Output Timings HDA_BIT_CLK HDA_SDOUT t143 t144 t143 t144 HDA_SDIN[3:0] t145 t146 Figure 8-25. Dual Channel Interface Timings tDQSL tDQS DQs tDH tDH tDS tDS DQ[7:0] Figure 8-26. Dual Channel Interface Timings DQ D Q [7 : 0 ] tDV W tDQ S Q tQ H tDQ S Q Datasheet 313 Electrical Characteristics Figure 8-27. LVDS Load and Transition Times Figure 8-28. Transmitting Position (Data to Strobe) CLKA/ CLKB Tppos0 YA/YB Tppos1 Tppos2 Tppos3 Tppos4 Tppos5 Tppos6 Figure 8-29. PCI Express* Transmitter Eye 314 Datasheet Electrical Characteristics Figure 8-30. PCI Express* Receiver Eye VTS-Diff = 0mV D+/D- Crossing point VRS-Diffp-p-Min>175mV .4 UI =TRX-EYE min Datasheet 315 Electrical Characteristics Figure 8-31. Measurement Points for Differential Waveforms Differential Clock - Single Ended Measurements V max = 1.15V Clock# V max = 1.15V Vcross max = 550mV Vcross max = 550mV Vcross min = 300 mV Vcross min = 300 mV Clock V min = -0.30V V min = -0.30V Clock# Vcross delta = 140mV Vcross delta = 140mV Clock Clock# Vcross median ll fa Vcross median T Vcross median +75mV Tr i se Clock# Vcross median -75mV Clock Clock Differential Clock - Differential Measurements Clock Period (Differential ) Positive Duty Cycle (Differential ) Negative Duty Cycle (Differential ) 0.0V Clock-Clock# Rise Edge Rate Fall Edge Rate Vih_min = +150 mV 0.0V Vil_max = -150 mV Clock-Clock# 316 Datasheet Electrical Characteristics Figure 8-32. PCH Test Load VccASW3_3 Figure 8-33. Controller Link Receive Timings t191 CL_CLK1 t190 t193 t194 CL_DATA1 Figure 8-34. Controller Link Receive Slew Rate t192 t192 CL_Vref + 50mV CL_Vref CL_Vref - 50mV CL_CLK1 / CL_DATA1 Figure 8-35. PCH Suspend Well Ramp Up/Down Requirement VCCSUS3_3 DCPSUS* VCCSUS3_3 > 1.0V T<10ms Datasheet 317 Electrical Characteristics Figure 8-36. Sequencing Requirements between PCH VCCSUS (1.05V) and External USB Vbus Vbus 1.05V VCCSUS (1.05V) 1. 1.05V-5% T=0us T=0us VCCSUS(1.05V) is in reference to DCPSUS rails. Figure 8-37. Sequencing Requirements between PCH VCC3_3 and VCC Core Rail VCC3_3 (3.3V) T2 <= 35 ms 2.6V T1 <= 25 ms 2.6V No Slew Rate Requirement 0V No Limit VCC (1.05V) 0.6V No Limit = Preferred Sequence = Alternative Sequence No Slew Rate Requirement 0V Figure 8-38. Sequencing Requirements between PCH VCC1_5 and VCC Core Rail VCC1_5 (1.5V) 1.35V T2 <= 35 ms T1 <= 25 ms 1.35V No Slew Rate Requirement 0V No Limit VCC (1.05V) 0.6V 0V 318 No Slew Rate Requirement No Limit = Preferred Sequence = Alternative Sequence Datasheet Electrical Characteristics 8.10 Sequencing Rails Within The Same Well Table 8-33. Suspend Well Voltage Ramp Up/Down Requirements Voltage Rail 1 Voltage Rail 2 Power Up Requirement Power Down Requirement VCCSUS3_3 DCPSUS1, DCPSUS2, DCPSUS3 VCCSUS3_3 must be powered up at most 10ms before DCPSUS*, but not after. VCCSUS3_3 must be powered down after DCPSUS*. VCCSUS (DCPSUS* rails) Platform USB Vbus VCCSUS ramps up before Vbus reaches 1.05V while ramping up. VCCSUS ramps down after Vbus reaches 1.05V while ramping down. In external VR mode (Mobile Only), this relationship needs to be met by the platform. In internal VR mode, the PCH will meet this timing. Table 8-34. Core Well Voltage Ramp Up/Down Requirements Voltage Rail 1 Voltage Rail 2 Power Up Requirement Power Down Requirement VCC (1.05V) VCC3_3 (3.3V) Preferred Option: * VCC powers up before VCC3_3 Alternative Option: * VCC3_3 may power up before VCC, but VCC must ramp up to 0.6V within 25ms of VCC3_3 ramping to 2.6V. Preferred Option: * VCC powers down after VCC3_3 Alternative Option: * VCC may power down before VCC3_3, but VCC3_3 must ramp down to 2.6V within 35ms assuming a linear ramp. VCC (1.05V) VCC1_5 (1.5V) Note 1, 2 Preferred Option: * VCC powers up before VCC1_5 Alternative Option: * VCC1_5 may power up before VCC, but VCC must ramp up to 0.6V within 25ms of VCC1_5 ramping to 1.35V. Preferred Option: * VCC powers down after VCC1_5 Alternative Option: * VCC may power down before VCC1_5, but VCC1_5 must ramp down to 1.35V within 35ms assuming a linear ramp. Notes: 1. VCC1_5 includes VCCADAC and VCCVRM. 2. For platforms not supporting VGA functionality, the VCCDAC rails may be tied to GND inherently meeting the "preferred" sequencing requirement. If they are tied to the 1.5V for platform layout simplicity even though the VGA/DAC functionality is not used, they must meet the specified sequencing requirement. 3. (Desktop Only) If T1 is < 25 ms, T2 35 ms + (25 ms - T1) Datasheet 319 Register and Memory Mapping 9 Register and Memory Mapping The PCH contains registers that are located in the processor I/O space and memory space and sets of PCI configuration registers that are located in PCI configuration space. This chapter describes the PCH I/O and memory maps at the register-set level. Register access is also described. Register-level address maps and Individual register bit descriptions are provided in the following chapters. The following notations and definitions are used in the register/instruction description chapters. Note: 320 All Chipset Registers are located in the core well unless otherwise indicated. RO Read Only. In some cases, if a register is read only, writes to this register location have no effect. However, in other cases, two separate registers are located at the same location where a read accesses one of the registers and a write accesses the other register. See the I/O and memory map tables for details. WO Write Only. In some cases, if a register is write only, reads to this register location have no effect. However, in other cases, two separate registers are located at the same location where a read accesses one of the registers and a write accesses the other register. See the I/O and memory map tables for details. R/W Read/Write. A register with this attribute can be read and written. R/WC Read/Write Clear. A register bit with this attribute can be read and written. However, a write of 1 clears (sets to 0) the corresponding bit and a write of 0 has no effect. R/WO Read/Write-Once. A register bit with this attribute can be written only once after power up. After the first write, the bit becomes read only. R/WL Read/Write Lockable. A register bit with the attribute can be read at any time but writes may only occur if the associated lock bit is set to unlock. If the associated lock bit is set to lock, this register bit becomes RO unless otherwise indicated. R/WLO Read/Write, Lock-Once. A register bit with this attribute can be written to the non-locked value multiple times, but to the locked value only once. After the locked value has been written, the bit becomes read only. R/W/SN Read/Write register initial value loaded from NVM. Reserved The value of reserved bits must never be changed. For details, see Section 9.2. Default When the PCH is reset, it sets its registers to predetermined default states. It is the responsibility of the system initialization software to determine configuration, operating parameters, and optional system features that are applicable, and to program the PCH registers accordingly. Bold Register bits that are highlighted in bold text indicate that the bit is implemented in the PCH. Register bits that are not implemented or are hardwired will remain in plain text. Datasheet Register and Memory Mapping 9.1 PCI Devices and Functions The PCH incorporates a variety of PCI devices and functions, as shown in Table 9-1. Device Functions can individually be disabled. The integrated Gigabit Ethernet controller will be disabled if no Platform LAN Connect component is detected (See Section 5.4). When a function is disabled, it does not appear at all to the software. A disabled function will not respond to any register reads or writes, insuring that these devices appear hidden to software. Table 9-1. PCI Devices and Functions Bus:Device:Function Bus 0:Device 31:Function 0 Function Description 1 LPC Controller Bus 0:Device 31:Function 2 SATA Controller #1 Bus 0:Device 31:Function 3 SMBus Controller Bus 0:Device 31:Function 5 SATA Controller #22 Bus 0:Device 31:Function 6 Thermal Subsystem Bus 0:Device 29:Function 03 USB EHCI Controller #1 Bus 0:Device 26:Function 03 USB EHCI Controller #2 Bus 0:Device 28:Function 0 PCI Express* Port 1 Bus 0:Device 28:Function 1 PCI Express Port 2 Bus 0:Device 28:Function 2 PCI Express Port 3 Bus 0:Device 28:Function 3 PCI Express Port 4 Bus 0:Device 28:Function 4 PCI Express Port 5 Bus 0:Device 28:Function 5 PCI Express Port 6 Bus 0:Device 28:Function 6 PCI Express Port 7 Bus 0:Device 28:Function 7 PCI Express Port 8 Bus 0:Device 27:Function 0 Intel(R) High Definition Audio Controller Bus 0:Device 25:Function 0 Gigabit Ethernet Controller Bus 0:Device 22:Function 0 Intel(R) Management Engine Interface #1 Bus 0:Device 22:Function 1 Intel Management Engine Interface #2 Bus 0:Device 22:Function 2 IDE-R Bus 0:Device 22:Function 3 KT Bus 0:Device 20:Function 0 xHCI Controller Notes: 1. The PCI-to-LPC bridge contains registers that control LPC, Power Management, System Management, GPIO, Processor Interface, RTC, Interrupts, Timers, and DMA. 2. SATA controller 2 (D31:F5) is only visible when D31:F2 CC.SCC=01h. 3. Prior to BIOS initialization of the PCH USB subsystem, the EHCI controllers will appear as Function 7. After BIOS initialization, the EHCI controllers will be Function 0. 4. This table shows the default PCI Express* Function Number-to-Root Port mapping. Function numbers for a given root port are assignable through the "Root Port Function Number and Hide for PCI Express Root Ports" register (RCBA+0404h). Datasheet 321 Register and Memory Mapping 9.2 PCI Configuration Map Each PCI function on the PCH has a set of PCI configuration registers. The register address map tables for these register sets are included at the beginning of the chapter for the particular function. Configuration Space registers are accessed through configuration cycles on the PCI bus by the Host bridge using configuration mechanism #1 detailed in the PCI Local Bus Specification, Revision 2.3. Some of the PCI registers contain reserved bits. Software must deal correctly with fields that are reserved. On reads, software must use appropriate masks to extract the defined bits and not rely on reserved bits being any particular value. On writes, software must ensure that the values of reserved bit positions are preserved. That is, the values of reserved bit positions must first be read, merged with the new values for other bit positions and then written back. The software does not need to perform read, merge, write operation for the configuration address register. In addition to reserved bits within a register, the configuration space contains reserved locations. Software should not write to reserved PCI configuration locations in the device-specific region (above address offset 3Fh). 9.3 I/O Map The I/O map is divided into Fixed and Variable address ranges. Fixed ranges cannot be moved, but in some cases can be disabled. Variable ranges can be moved and can also be disabled. 9.3.1 Fixed I/O Address Ranges Table 9-2 shows the Fixed I/O decode ranges from the processor perspective. For each I/O range, there may be separate behavior for reads and writes. DMI (Direct Media Interface) cycles that go to target ranges that are marked as "Reserved" will not be decoded by the PCH, and will be passed to PCI, unless the Subtractive Decode Policy bit is set (D31:F0:Offset 42h, bit 0). If a PCI master targets one of the fixed I/O target ranges, it will be positively decoded by the PCH in medium speed. Address ranges that are not listed or marked "Reserved" are not decoded by the PCH (unless assigned to one of the variable ranges). Table 9-2. Fixed I/O Ranges Decoded by PCH (Sheet 1 of 3) I/O Address Read Target Write Target Internal Unit 00h-08h DMA Controller DMA Controller DMA 09h-0Eh RESERVED DMA Controller DMA 0Fh DMA Controller DMA Controller DMA 10h-18h DMA Controller DMA Controller DMA 19h-1Eh RESERVED DMA Controller DMA 322 1Fh DMA Controller DMA Controller DMA 20h-21h Interrupt Controller Interrupt Controller Interrupt 24h-25h Interrupt Controller Interrupt Controller Interrupt 28h-29h Interrupt Controller Interrupt Controller Interrupt 2Ch-2Dh Interrupt Controller Interrupt Controller Interrupt Datasheet Register and Memory Mapping Table 9-2. Fixed I/O Ranges Decoded by PCH (Sheet 2 of 3) I/O Address Read Target Write Target Internal Unit 2Eh-2Fh LPC SIO LPC SIO Forwarded to LPC 30h-31h Interrupt Controller Interrupt Controller Interrupt 34h-35h Interrupt Controller Interrupt Controller Interrupt 38h-39h Interrupt Controller Interrupt Controller Interrupt 3Ch-3Dh Interrupt Controller Interrupt Controller Interrupt 40h-42h Timer/Counter Timer/Counter PIT (8254) 43h RESERVED Timer/Counter PIT 4Eh-4Fh LPC SIO LPC SIO Forwarded to LPC 50h-52h Timer/Counter Timer/Counter PIT 53h RESERVED Timer/Counter PIT 60h Microcontroller Microcontroller Forwarded to LPC 61h NMI Controller NMI Controller Processor I/F 62h Microcontroller Microcontroller Forwarded to LPC 64h Microcontroller Microcontroller Forwarded to LPC 66h Microcontroller Microcontroller Forwarded to LPC 70h RESERVED1 NMI and RTC Controller RTC 71h RTC Controller RTC Controller RTC 72h RTC Controller NMI and RTC Controller RTC 73h RTC Controller RTC Controller RTC 74h RTC Controller NMI and RTC Controller RTC 75h RTC Controller RTC Controller RTC 76h RTC Controller NMI and RTC Controller RTC 77h RTC Controller RTC Controller RTC 80h DMA Controller, LPC, PCI, or PCIe* DMA Controller and LPC, PCI, or PCIe DMA 81h-83h DMA Controller DMA Controller DMA 84h-86h DMA Controller DMA Controller and LPC, PCI, or PCIe DMA 87h DMA Controller DMA Controller DMA 88h DMA Controller DMA Controller and LPC, PCI, or PCIe DMA 89h-8Bh DMA Controller DMA Controller DMA 8Ch-8Eh DMA Controller DMA Controller and LPC, PCI, or PCIe DMA 8Fh DMA Controller DMA Controller DMA 90h-91h DMA Controller DMA Controller DMA 92h Reset Generator Reset Generator Processor I/F 93h-9Fh DMA Controller DMA Controller DMA A0h-A1h Interrupt Controller Interrupt Controller Interrupt A4h-A5h Interrupt Controller Interrupt Controller Interrupt A8h-A9h Interrupt Controller Interrupt Controller Interrupt ACh-ADh Interrupt Controller Interrupt Controller Interrupt B0h-B1h Interrupt Controller Interrupt Controller Interrupt B2h-B3h Power Management Power Management Power Management B4h-B5h Interrupt Controller Interrupt Controller Interrupt B8h-B9h Interrupt Controller Interrupt Controller Interrupt BCh-BDh Interrupt Controller Interrupt Controller Interrupt C0h-D1h DMA Controller DMA Controller DMA Datasheet 323 Register and Memory Mapping Table 9-2. Fixed I/O Ranges Decoded by PCH (Sheet 3 of 3) I/O Address Read Target Write Target Internal Unit D2h-DDh RESERVED DMA Controller DMA DEh-DFh DMA Controller DMA Controller DMA F0h FERR# / Interrupt Controller FERR# / Interrupt Controller Processor I/F 170h-177h SATA Controller, PCI, or PCIe SATA Controller, PCI, or PCIe* SATA 1F0h-1F7h SATA Controller, PCI, or PCIe SATA Controller, PCI, or PCIe SATA 200h-207h Gameport Low Gameport Low Forwarded to LPC 208h-20Fh Gameport High Gameport High Forwarded to LPC 376h SATA Controller, PCI, or PCIe SATA Controller, PCI, or PCIe SATA 3F6h SATA Controller, PCI, or PCIe SATA Controller, PCI, or PCIe SATA 4D0h-4D1h Interrupt Controller Interrupt Controller Interrupt CF9h Reset Generator Reset Generator Processor I/F Note: 1. See Section 12.7.2 9.3.2 Variable I/O Decode Ranges Table 9-3 shows the Variable I/O Decode Ranges. They are set using Base Address Registers (BARs) or other configuration bits in the various PCI configuration spaces. The PNP software (PCI or ACPI) can use their configuration mechanisms to set and adjust these values. Warning: The Variable I/O Ranges should not be set to conflict with the Fixed I/O Ranges. Unpredictable results if the configuration software allows conflicts to occur. The PCH does not perform any checks for conflicts. Table 9-3. Variable I/O Decode Ranges (Sheet 1 of 2) Range Name 324 Mappable Size (Bytes) Target ACPI Anywhere in 64 KB I/O Space 64 Power Management IDE Bus Master Anywhere in 64 KB I/O Space 1. 16 or 32 2. 16 1. SATA Host Controller #1, #2 2. IDE-R Native IDE Command Anywhere in 64 KB I/O Space1 8 1. SATA Host Controller #1, #2 2. IDE-R Native IDE Control Anywhere in 64 KB I/O Space1 4 1. SATA Host Controller #1, #2 2. IDE-R SATA Index/Data Pair Anywhere in 64 KB I/O Space 16 SATA Host Controller #1, #2 SMBus SMB Unit Anywhere in 64 KB I/O Space 32 TCO 96 Bytes above ACPI Base 32 TCO Unit GPIO Anywhere in 64 KB I/O Space 128 GPIO Unit Parallel Port 3 Ranges in 64 KB I/O Space 83 LPC Peripheral Serial Port 1 8 Ranges in 64 KB I/O Space 8 LPC Peripheral Serial Port 2 8 Ranges in 64 KB I/O Space 8 LPC Peripheral Floppy Disk Controller 2 Ranges in 64 KB I/O Space 8 LPC Peripheral LAN Anywhere in 64 KB I/O Space 322 LAN Unit LPC Generic 1 Anywhere in 64 KB I/O Space 4 to 256 LPC Peripheral Datasheet Register and Memory Mapping Table 9-3. Variable I/O Decode Ranges (Sheet 2 of 2) Mappable Size (Bytes) Target LPC Generic 2 Anywhere in 64 KB I/O Space 4 to 256 LPC Peripheral LPC Generic 3 Anywhere in 64 KB I/O Space 4 to 256 LPC Peripheral LPC Generic 4 Anywhere in 64 KB I/O Space 4 to 256 LPC Peripheral I/O Trapping Ranges Anywhere in 64 KB I/O Space 1 to 256 Trap on Backbone PCI Bridge Anywhere in 64 KB I/O Space I/O Base/ Limit PCI Bridge PCI Express* Root Ports Anywhere in 64 KB I/O Space I/O Base/ Limit PCI Express Root Ports 1- 8 KT Anywhere in 64 KB I/O Space 8 KT Range Name Notes: 1. All ranges are decoded directly from DMI. The I/O cycles will not be seen on PCI, except the range associated with PCI bridge. 2. The LAN range is typically not used, as the registers can also be accessed using a memory space. 3. There is also an alias 400h above the parallel port range that is used for ECP parallel ports. 9.4 Memory Map Table 9-4 shows (from the processor perspective) the memory ranges that the PCH decodes. Cycles that arrive from DMI that are not directed to any of the internal memory targets that decode directly from DMI will be driven out on PCI unless the Subtractive Decode Policy bit is set (D31:F0:Offset 42h, bit 0). PCI cycles generated by external PCI masters will be positively decoded unless they fall in the PCI-to-PCI bridge memory forwarding ranges (those addresses are reserved for PCI peer-to-peer traffic). If the cycle is not in the internal LAN controller's range, it will be forwarded up to DMI. Software must not attempt locks to the PCH memory-mapped I/O ranges for EHCI and HPET. If attempted, the lock is not honored which means potential deadlock conditions may occur. Table 9-4. Memory Decode Ranges from Processor Perspective (Sheet 1 of 3) Memory Range Target Dependency/Comments 0000 0000h-000D FFFFh 0010 0000h-TOM (Top of Memory) Main Memory 000E 0000h-000E FFFFh LPC or SPI Bit 6 in BIOS Decode Enable register is set 000F 0000h-000F FFFFh LPC or SPI Bit 7 in BIOS Decode Enable register is set FEC_ _000h-FEC_ _040h IO(x) APIC inside PCH TOM registers in Host controller _ _is controlled using APIC Range Select (ASEL) field and APIC Enable (AEN) bit FEC1 0000h-FEC1 7FFF PCI Express* Port 1 PCI Express* Root Port 1 I/OxAPIC Enable (PAE) set FEC1 8000h-FEC1 FFFFh PCI Express* Port 2 PCI Express* Root Port 2 I/OxAPIC Enable (PAE) set FEC2 0000h-FEC2 7FFFh PCI Express* Port 3 PCI Express* Root Port 3 I/OxAPIC Enable (PAE) set FEC2 8000h-FEC2 FFFFh PCI Express* Port 4 PCI Express* Root Port 4 I/OxAPIC Enable (PAE) set FEC3 0000h-FEC3 7FFFh PCI Express* Port 5 PCI Express* Root Port 5 I/OxAPIC Enable (PAE) set FEC3 8000h-FEC3 FFFFh PCI Express* Port 6 PCI Express* Root Port 6 I/OxAPIC Enable (PAE) set FEC4 0000h-FEC4 7FFF PCI Express* Port 7 PCI Express* Root Port 7 I/OxAPIC Enable (PAE) set FEC4 8000h-FEC4 FFFF PCI Express* Port 8 PCI Express* Root Port 8 I/OxAPIC Enable (PAE) set Datasheet 325 Register and Memory Mapping Table 9-4. Memory Decode Ranges from Processor Perspective (Sheet 2 of 3) Memory Range Target Dependency/Comments FFC0 0000h-FFC7 FFFFh FF80 0000h-FF87 FFFFh LPC or SPI (or PCI)2 Bit 8 in BIOS Decode Enable register is set FFC8 0000h-FFCF FFFFh FF88 0000h-FF8F FFFFh LPC or SPI (or PCI)2 Bit 9 in BIOS Decode Enable register is set FFD0 0000h-FFD7 FFFFh FF90 0000h-FF97 FFFFh LPC or SPI (or PCI)2 Bit 10 in BIOS Decode Enable register is set FFD8 0000h-FFDF FFFFh FF98 0000h-FF9F FFFFh LPC or SPI (or PCI)2 Bit 11 in BIOS Decode Enable register is set FFE0 000h-FFE7 FFFFh FFA0 0000h-FFA7 FFFFh LPC or SPI (or PCI)2 Bit 12 in BIOS Decode Enable register is set FFE8 0000h-FFEF FFFFh FFA8 0000h-FFAF FFFFh LPC or SPI (or PCI)2 Bit 13 in BIOS Decode Enable register is set FFF0 0000h-FFF7 FFFFh FFB0 0000h-FFB7 FFFFh LPC or SPI (or PCI)2 Bit 14 in BIOS Decode Enable register is set FFF8 0000h-FFFF FFFFh FFB8 0000h-FFBF FFFFh LPC or SPI (or PCI)2 Always enabled. The top two 64 KB blocks of this range can be swapped, as described in Section 9.4.1. FF70 0000h-FF7F FFFFh FF30 0000h-FF3F FFFFh LPC or SPI (or PCI)2 Bit 3 in BIOS Decode Enable register is set FF60 0000h-FF6F FFFFh FF20 0000h-FF2F FFFFh LPC or SPI (or PCI)2 Bit 2 in BIOS Decode Enable register is set FF50 0000h-FF5F FFFFh FF10 0000h-FF1F FFFFh LPC or SPI (or PCI)2 Bit 1 in BIOS Decode Enable register is set FF40 0000h-FF4F FFFFh FF00 0000h-FF0F FFFFh LPC or SPI (or PCI)2 Bit 0 in BIOS Decode Enable register is set 128 KB anywhere in 4 GB range Integrated LAN Controller Enable using BAR in D25:F0 (Integrated LAN Controller MBARA) 4 KB anywhere in 4 GB range Integrated LAN Controller Enable using BAR in D25:F0 (Integrated LAN Controller MBARB) 1 KB anywhere in 4 GB range USB EHCI Controller #11 Enable using standard PCI mechanism (D29:F0) 1 1 KB anywhere in 4 GB range USB EHCI Controller #2 64 KB anywhere in 4 GB range USB xHCI Controller Enable using standard PCI mechanism (D20:F0) 16 KB anywhere in 64-bit addressing space Intel(R) High Definition Audio Host Controller Enable using standard PCI mechanism (D27:F0) FED0 X000h-FED0 X3FFh High Precision Event Timers BIOS determines the "fixed" location which is one of four, 1KB ranges where X (in the first column) is 0h, 1h, 2h, or 3h. 1 Enable using standard PCI mechanism (D26:F0) FED4 0000h-FED4 FFFFh TPM on LPC None Memory Base/Limit anywhere in 4 GB range PCI Bridge Enable using standard PCI mechanism (D30:F0) Prefetchable Memory Base/Limit anywhere in 64-bit address range PCI Bridge Enable using standard PCI mechanism (D30:F0) 64 KB anywhere in 4 GB range LPC 32 Bytes anywhere in 64-bit address range SMBus 2 KB anywhere above 64 KB to 4 GB range SATA Host Controller #1 326 LPC Generic Memory Range. Enable using setting bit[0] of the LPC Generic Memory Range register (D31:F0:offset 98h). Enable using standard PCI mechanism (D31:F3) AHCI memory-mapped registers. Enable using standard PCI mechanism (D31:F2) Datasheet Register and Memory Mapping Table 9-4. Memory Decode Ranges from Processor Perspective (Sheet 3 of 3) Memory Range Target Dependency/Comments Memory Base/Limit anywhere in 4 GB range PCI Express* Root Ports 1-8 Enable using standard PCI mechanism (D28: F 0-7) Prefetchable Memory Base/Limit anywhere in 64-bit address range PCI Express Root Ports 1-8 Enable using standard PCI mechanism (D28:F 0-7) 4 KB anywhere in 64-bit address range Thermal Reporting Enable using standard PCI mechanism (D31:F6 TBAR/ TBARH) 4 KB anywhere in 64-bit address range Thermal Reporting Enable using standard PCI mechanism (D31:F6 TBARB/ TBARBH) 16 Bytes anywhere in 64-bit address range Intel(R) MEI #1, #2 Enable using standard PCI mechanism (D22:F 1:0) 4 KB anywhere in 4 GB range KT 16 KB anywhere in 4 GB range Root Complex Register Block (RCRB) Enable using standard PCI mechanism (D22:F3) Enable using setting bit[0] of the Root Complex Base Address register (D31:F0:offset F0h). Notes: 1. Software must not attempt locks to memory mapped I/O ranges for USB EHCI or High Precision Event Timers. If attempted, the lock is not honored, which means potential deadlock conditions may occur. 2. PCI is the target when the Boot BIOS Destination selection bits are set to 10b (Chipset Config Registers:Offset 3401 bits 11:10). When PCI selected, the Firmware Hub Decode Enable bits have no effect. 9.4.1 Boot-Block Update Scheme The PCH supports a "Top Swap" mode that has the PCH swap the top block in the FWH or SPI flash (the boot-block) with another location. This allows for safe update of the boot-block (even if a power failure occurs). When the "Top Swap" Enable bit is set, the PCH will invert A16 for cycles going to the upper two 64 KB blocks in the FWH or appropriate address lines as selected in BIOS Boot-Block size soft strap for SPI. Specifically for FHW, in this mode accesses to FFFF_0000h-FFFF_FFFFh are directed to FFFE_0000h-FFFE_FFFFh and vice versa. When the Top Swap Enable bit is 0, the PCH will not invert A16. Specifically for SPI, in this mode the "Top Swap" behavior is as described below. When the Top Swap Enable bit is 0, the PCH will not invert any address bit. Table 9-5. SPI Mode Address Swapping BIOS Boot-Block size Value Accesses to Being Directed to 000 (64 KB) FFFF_0000h-FFFF_FFFFh FFFE_0000h-FFFE_FFFFh and vice versa 001 (128 KB) FFFE_0000h-FFFF_FFFFh FFFC_0000h-FFFD_FFFFh and vice versa 010 (256 KB) FFFC_0000h-FFFF_FFFFh FFF8_0000h-FFFB_FFFFh and vice versa 011 (512 KB)1 FFF8_0000h-FFFF_FFFFh FFF0_0000h-FFF7_FFFFh and vice versa 100 (1 MB)1 101-111 FFF0_0000h-FFFF_FFFFh FFE0_0000h-FFEF_FFFFh and vice versa Reserved Reserved Notes: 1. Only available in Server SKU. Datasheet 327 Register and Memory Mapping This bit is automatically set to 0 by RTCRST#, but not by PLTRST#. The scheme is based on the concept that the top block is reserved as the "boot" block, and the block immediately below the top block is reserved for doing boot-block updates. The algorithm is: 1. Software copies the top block to the block immediately below the top 2. Software checks that the copied block is correct. This could be done by performing a checksum calculation. 3. Software sets the Top Swap bit. This will invert the appropriate address bits for the cycles going to the FWH or SPI. 4. Software erases the top block 5. Software writes the new top block 6. Software checks the new top block 7. Software clears the Top Swap bit If a power failure occurs at any point after step 3, the system will be able to boot from the copy of the boot-block that is stored in the block below the top. This is because the Top Swap bit is backed in the RTC well. Note: The "Top Swap" mode may be forced by an external strapping option. When top swap mode is forced in this manner, the Top Swap bit cannot be cleared by software. A reboot with the strap removed will be required to exit a forced top-block swap mode. Note: Top swap mode only affects accesses to the Firmware Hub space, not feature space for FWH. Note: The top swap mode has no effect on accesses below FFFE_0000h for FWH. 328 Datasheet Chipset Configuration Registers 10 Chipset Configuration Registers This section describes all registers and base functionality that is related to chipset configuration and not a specific interface (such as LPC, USB, or PCI Express*). It contains the root complex register block that describes the behavior of the upstream internal link. This block is mapped into memory space, using the Root Complex Base Address (RCBA) register of the PCI-to-LPC bridge. Accesses in this space must be limited to 32-bit (DW) quantities. Burst accesses are not allowed. 10.1 Chipset Configuration Registers (Memory Space) Note: Address locations that are not shown should be treated as Reserved (see Section 9.2 for details). Table 10-1. Chipset Configuration Register Memory Map (Memory Space) (Sheet 1 of 2) Offset Datasheet Mnemonic 0400h-0403 RPC 0404h-0407h RPFN 0408h-040Bh FLRSTAT 1E00h-1E03h Register Name Default Attribute Root Port Configuration 0000000yh R/W, RO Root Port Function Number and Hide for PCI Express Root Ports 76543210h R/W, R/WO Function Level Reset Pending Status Summary 00000000h RO/V TRSR Trap Status 00000000h R/WC, RO 1E10h-1E17h TRCR Trapped Cycle 00000000000 00000h RO 1E18h-1E1Fh TWDR Trapped Write Data 00000000000 00000h RO 1E80h-1E87h IOTR0 I/O Trap Register 0 00000000000 00000h R/W 1E88h-1E8Fh IOTR1 I/O Trap Register 1 00000000000 00000h R/W 1E90h-1E97h IOTR2 I/O Trap Register 2 00000000000 00000h R/W 1E98h-1E9Fh IOTR3 I/O Trap Register 3 00000000000 00000h R/W 2014h-2017h V0CTL Virtual Channel 0 Resource Control 80000010h R/WL, RO 201Ah-201Bh V0STS Virtual Channel 0 Resource Status 0000h RO 2020h-2023h V1CTL Virtual Channel 1 Resource Control 00000000h R/W, RO, R/ WL 2026h-2027h V1STS Virtual Channel 1 Resource Status 0000h RO 20ACh-20AFh REC Root Error Command 21A4h-21A7h LCAP Link Capabilities 21A8h-21A9h LCTL 21AAh-21ABh LSTS 3000h TCTL 3100h-3103h D31IP 0000h R/W 00012A42h RO, R/WO Link Control 0000h R/W Link Status 0041h RO TCO Configuration Device 31 Interrupt Pin 00h R/W 03243200h R/W, RO 329 Chipset Configuration Registers Table 10-1. Chipset Configuration Register Memory Map (Memory Space) (Sheet 2 of 2) Offset 330 Mnemonic Register Name Default Attribute 3104h-3107h D30IP Device 30 Interrupt Pin 00000000h RO 3108h-310Bh D29IP Device 29 Interrupt Pin 10004321h R/W 310Ch-310Fh D28IP Device 28 Interrupt Pin 00214321h R/W 3110h-3113h D27IP Device 27 Interrupt Pin 00000001h R/W 3114h-3117h D26IP Device 26 Interrupt Pin 30000321h R/W 3118h-311Bh D25IP Device 25 Interrupt Pin 00000001h R/W 3124h-3127h D22IP Device 22 Interrupt Pin 00004321h R/W 3128h-312Bh D20IP Device 20 Interrupt Pin 00000021h R/W 3140h-3141h D31IR Device 31 Interrupt Route 3210h R/W 3144h-3145h D29IR Device 29 Interrupt Route 3210h R/W 3146h-3147h D28IR Device 28 Interrupt Route 3210h R/W 3148h-3149h D27IR Device 27 Interrupt Route 3210h R/W 314Ch-314Dh D26IR Device 26 Interrupt Route 3210h R/W 3150h-3151h D25IR Device 25 Interrupt Route 3210h R/W 315Ch-315Dh D22IR Device 22 Interrupt Route 3210h R/W 3160h-3161h D20IR Device 20 Interrupt Route 3210h R/W 31FEh-31FFh OIC 0000h R/W 3300h-3303h WADT_AC Wake Alarm Device Timer - AC FFFFFFFFh R/W Wake Alarm Device Timer - DC FFFFFFFFh R/W Wake Alarm Device Expired Timer - AC FFFFFFFFh R/W 3304h-3307h WADT_DC 3308h-330Bh WADT_EXP_AC 330Ch-330Fh WADT_EXP_DC 3310h-3313h PRSTS Other Interrupt Control Wake Alarm Device Expired Timer - DC FFFFFFFFh R/W Power and Reset Status 05000000h RO, R/WC Power Management Configuration 00000020h R/W Deep Sx From S3 Power Policies 00000000h R/W 3318h-331Bh PM_CFG 3328h-332Bh DEEP_S3_POL 332Ch-332Fh DEEP_S4_POL Deep Sx From S4 Power Policies 00000000h R/W 3330h-3333h DEEP_S5_POL Deep Sx From S5 Power Policies 00000000h R/W 3334-3337h DSX_CFG Deep Sx Configuration Register 00000000h R/W 33C8h-33CBh PMSYNC_CFG PMSYNC Configuration 00000000h R/W RTC Configuration 00000000h R/W, R/WLO High Precision Timer Configuration 00000000h R/W 000000yy0h R/W, R/WLO 00h R/W 3400h-3403h RC 3404h-3407h HPTC 3410h-3413h GCS General Control and Status 3414h BUC Backed Up Control 3418h-341Bh FD Function Disable 00000000h R/W 341Ch-341Fh CG Clock Gating 00000000h R/W 3420h FDSW 3424h-3425h DISPBDF 3428h-342Bh FD2 00h R/W Display Bus, Device and Function Initialization Function Disable SUS Well 00040010h R/W Function Disable 2 00000000h R/W Datasheet Chipset Configuration Registers 10.1.1 RPC--Root Port Configuration Register Offset Address: 0400-0403h Default Value: 0000000yh (y = 00xxb) Bit 31:0 10.1.2 Attribute: Size: R/W, RO 32-bit Description Reserved. BIOS may write to this register, as needed. RPFN--Root Port Function Number and Hide for PCI Express* Root Ports Register Offset Address: 0404-0407h Default Value: 76543210h Attribute: Size: R/W, R/WO 32-bit For the PCI Express root ports, the assignment of a function number to a root port is not fixed. BIOS may re-assign the function numbers on a port by port basis. This capability will allow BIOS to disable/hide any root port and still have functions 0 thru N1 where N is the total number of enabled root ports. Port numbers will remain fixed to a physical root port. The existing root port Function Disable registers operate on physical ports (not functions). Port Configuration (1x4, 4x1, and so on) is not affected by the logical function number assignment and is associated with physical ports. Note: Datasheet The difference between hiding versus disabling a port is that a hidden port is not able to claim downstream Config cycles only. Memory and I/O cycles are still claimed by that hidden port. A disabled port is turned off and not able to claim downstream Configuration, Memory and I/O cycles - it saves power. For PCIe ports that are multiplexed out through Flexible I/O (so the alternative I/O technology, USB3 or SATA, is chosen), the PCIe* port is disabled (not hidden). Function disable is covered in Section 10.1.51. Bit Description 31 Root Port 8 Config Hide (RP8CH)--R/W. This bit is used to hide the root port and any devices behind it from being discovered by the OS. When set to 1, the root port will not claim any downstream configuration transactions. 30:28 Root Port 8 Function Number (RP8FN)--R/WO. These bits set the function number for PCI Express* Root Port 8. This root port function number must be a unique value from the other root port function numbers. 27 Root Port 7 Config Hide (RP7CH)--R/W. This bit is used to hide the root port and any devices behind it from being discovered by the OS. When set to 1, the root port will not claim any downstream configuration transactions. 26:24 Root Port 7 Function Number (RP7FN)--R/WO. These bits set the function number for PCI Express Root Port 7. This root port function number must be a unique value from the other root port function numbers. 23 Root Port 6 Config Hide (RP6CH)--R/W. This bit is used to hide the root port and any devices behind it from being discovered by the OS. When set to 1, the root port will not claim any downstream configuration transactions. 22:20 Root Port 6 Function Number (RP6FN)--R/WO. These bits set the function number for PCI Express Root Port 6. This root port function number must be a unique value from the other root port function numbers. 19 Root Port 5 Config Hide (RP5CH)--R/W. This bit is used to hide the root port and any devices behind it from being discovered by the OS. When set to 1, the root port will not claim any downstream configuration transactions. 331 Chipset Configuration Registers 332 Bit Description 18:16 Root Port 5 Function Number (RP5FN)--R/WO. These bits set the function number for PCI Express Root Port 5. This root port function number must be a unique value from the other root port function numbers. 15 Root Port 4 Config Hide (RP4CH)--R/W. This bit is used to hide the root port and any devices behind it from being discovered by the OS. When set to 1, the root port will not claim any downstream configuration transactions. 14:12 Root Port 4 Function Number (RP4FN)--R/WO. These bits set the function number for PCI Express Root Port 4. This root port function number must be a unique value from the other root port function numbers. 11 Root Port 3 Config Hide (RP3CH)--R/W. This bit is used to hide the root port and any devices behind it from being discovered by the OS. When set to 1, the root port will not claim any downstream configuration transactions. 10:8 Root Port 3 Function Number (RP3FN)--R/WO. These bits set the function number for PCI Express Root Port 3. This root port function number must be a unique value from the other root port function numbers. 7 Root Port 2 Config Hide (RP2CH)--R/W. This bit is used to hide the root port and any devices behind it from being discovered by the OS. When set to 1, the root port will not claim any downstream configuration transactions. 6:4 Root Port 2 Function Number (RP2FN)--R/WO. These bits set the function number for PCI Express* Root Port 2. This root port function number must be a unique value from the other root port function numbers. 3 Root Port 1 Config Hide (RP1CH)--R/W. This bit is used to hide the root port and any devices behind it from being discovered by the OS. When set to 1, the root port will not claim any downstream configuration transactions. 2:0 Root Port 1 Function Number (RP1FN)--R/WO. These bits set the function number for PCI Express Root Port 1. This root port function number must be a unique value from the other root port function numbers. Datasheet Chipset Configuration Registers 10.1.3 FLRSTAT--Function Level Reset Pending Status Register Offset Address: 0408-040Bh Default Value: 00000000h Bit 31:24 23 22:16 15 14:0 10.1.4 RO/V 32-bit Attribute: Size: R/WC, RO 32-bit Description Reserved FLR Pending Status for D29:F0, EHCI #1--RO/V. 0 = Function Level Reset is not pending. 1 = Function Level Reset is pending. Reserved FLR Pending Status for D26:F0, EHCI #2--RO/V. 0 = Function Level Reset is not pending. 1 = Function Level Reset is pending. Reserved TRSR--Trap Status Register Offset Address: 1E00-1E03h Default Value: 00000000h Bit 31:4 3:0 Datasheet Attribute: Size: Description Reserved Cycle Trap SMI# Status (CTSS)--R/WC. These bits are set by hardware when the corresponding Cycle Trap register is enabled and a matching cycle is received (and trapped). These bits are OR'ed together to create a single status bit in the Power Management register space. The SMI# and trapping must be enabled in order to set these bits. These bits are set before the completion is generated for the trapped cycle, thereby ensuring that the processor can enter the SMI# handler when the instruction completes. Each status bit is cleared by writing a 1 to the corresponding bit location in this register. 333 Chipset Configuration Registers 10.1.5 TRCR--Trapped Cycle Register Offset Address: 1E10-1E17h Default Value: 0000000000000000h Attribute: Size: RO 64-bit This register saves information about the I/O Cycle that was trapped and generated the SMI# for software to read. Bit 63:25 24 Reserved Read/Write# (RWI)--RO. 0 = Trapped cycle was a write cycle. 1 = Trapped cycle was a read cycle. 23:20 Reserved 19:16 Active-high Byte Enables (AHBE)--RO. This is the DWord-aligned byte enables associated with the trapped cycle. A 1 in any bit location indicates that the corresponding byte is enabled in the cycle. 15:2 1:0 10.1.6 Description Trapped I/O Address (TIOA)--RO. This is the DWord-aligned address of the trapped cycle. Reserved TWDR--Trapped Write Data Register Offset Address: 1E18-1E1Fh Default Value: 0000000000000000h Attribute: Size: RO 64-bit This register saves the data from I/O write cycles that are trapped for software to read. Bit 63:32 31:0 334 Description Reserved Trapped I/O Data (TIOD)--RO. DWord of I/O write data. This field is undefined after trapping a read cycle. Datasheet Chipset Configuration Registers 10.1.7 IOTRn--I/O Trap Register (0-3) Offset Address: 1E80-1E87h Register 0 1E88-1E8Fh Register 1 1E90-1E97h Register 2 1E98-1E9Fh Register 3 Default Value: 0000000000000000h Attribute: R/W Size: 64-bit These registers are used to specify the set of I/O cycles to be trapped and to enable this functionality. Bit 63:50 Reserved 49 Read/Write Mask (RWM)--R/W. 0 = The cycle must match the type specified in bit 48. 1 = Trapping logic will operate on both read and write cycles. 48 Read/Write# (RWIO)--R/W. 0 = Write 1 = Read Note: The value in this field does not matter if bit 49 is set. 47:40 Reserved 39:36 Byte Enable Mask (BEM)--R/W. A 1 in any bit position indicates that any value in the corresponding byte enable bit in a received cycle will be treated as a match. The corresponding bit in the Byte Enables field, below, is ignored. 35:32 Byte Enables (TBE)--R/W. Active-high DWord-aligned byte enables. 31:24 Reserved 23:18 Address[7:2] Mask (ADMA)--R/W. A 1 in any bit position indicates that any value in the corresponding address bit in a received cycle will be treated as a match. The corresponding bit in the Address field, below, is ignored. The mask is only provided for the lower 6 bits of the DWord address, allowing for traps on address ranges up to 256 bytes in size. 17:16 Reserved 15:2 Datasheet Description I/O Address[15:2] (IOAD)--R/W. DWord-aligned address 1 Reserved 0 Trap and SMI# Enable (TRSE)--R/W. 0 = Trapping and SMI# logic disabled. 1 = The trapping logic specified in this register is enabled. 335 Chipset Configuration Registers 10.1.8 V0CTL--Virtual Channel 0 Resource Control Register Offset Address: 2014-2017h Default Value: 80000010h Bit 31 Description Virtual Channel Enable (EN)--RO. Always set to 1. VC0 is always enabled and cannot be disabled. Reserved 26:24 Virtual Channel Identifier (ID)--RO. Indicates the ID to use for this virtual channel. 23:16 Reserved 15:10 Extended TC/VC Map (ETVM)--R/WL. Defines the upper 8-bits of the VC0 16-bit TC/VC mapping registers. These registers use the PCI Express reserved TC[3] traffic class bit. These bits are locked if the TCLOCKDN bit (RCBA+0050h:bit 31) is set. 9:7 Reserved 6:1 Transaction Class / Virtual Channel Map (TVM)--R/WL. Indicates which transaction classes are mapped to this virtual channel. When a bit is set, this transaction class is mapped to the virtual channel. These bits are locked if the TCLOCKDN bit (RCBA+0050h:bit 31) is set. Reserved V0STS--Virtual Channel 0 Resource Status Register Offset Address: 201A-201Bh Default Value: 0000h Bit 15:2 10.1.10 Attribute: Size: RO 16-bit Description Reserved 1 VC Negotiation Pending (NP)--RO. When set, this bit indicates the virtual channel is still being negotiated with ingress ports. 0 Reserved V1CTL--Virtual Channel 1 Resource Control Register Offset Address: 2020-2023h Default Value: 00000000h Bit 31 Attribute: Size: R/W, RO, R/WL 32-bit Description Virtual Channel Enable (EN)--R/W. Enables the VC when set. Disables the VC when cleared. 30:28 Reserved 27:24 Virtual Channel Identifier (ID)--R/W. Indicates the ID to use for this virtual channel. 23:16 Reserved 15:10 Extended TC/VC Map (ETVM)--R/WL. Defines the upper 8-bits of the VC0 16-bit TC/VC mapping registers. These registers use the PCI Express* reserved TC[3] traffic class bit. These bits are locked if the TCLOCKDN bit (RCBA+0050h:bit 31) is set. 9:8 Reserved 7:1 Transaction Class / Virtual Channel Map (TVM)--R/WL. Indicates which transaction classes are mapped to this virtual channel. When a bit is set, this transaction class is mapped to the virtual channel. These bits are locked if the TCLOCKDN bit (RCBA+0050h:bit 31) is set. 0 336 R/WL, RO 32-bit 30:27 0 10.1.9 Attribute: Size: Reserved Datasheet Chipset Configuration Registers 10.1.11 V1STS--Virtual Channel 1 Resource Status Register Offset Address: 2026-2027h Default Value: 0000h Bit 15:2 10.1.12 Attribute: Size: Description Reserved 1 VC Negotiation Pending (NP)--RO. When set, this bit indicates the virtual channel is still being negotiated with ingress ports. 0 Reserved REC--Root Error Command Register Offset Address: 20AC-20AFh Default Value: 0000h Attribute: Size: Description 31 Drop Poisoned Downstream Packets (DPDP)--R/W. Determines how downstream packets on DMI are handled that are received with the EP field set, indicating poisoned data: 0 = Packets are forwarded downstream without forcing the UT field set. 1 = This packet and all subsequent packets with data received on DMI for any VC will have their Unsupported Transaction (UT) field set causing them to master Abort downstream. Packets without data such as memory, I/O and config read requests are allowed to proceed. Reserved LCAP--Link Capabilities Register Offset Address: 21A4-21A7h Default Value: 00012A42h Bit Datasheet R/W 32-bit Bit 30:0 10.1.13 RO 16-bit Attribute: Size: R/WO, RO 32-bit Description 31:18 Reserved 17:15 L1 Exit Latency (EL1)--R/WO. 000b = Less than 1 s 001b = 1 s to less than 2 s 010b = 2 s to less than 4 s 011b = 4 s to less than 8 s 100b = 8 s to less than 16 s 101b = 16 s to less than 32 s 110b = 32 s to 64 s 111b = More than 64 s 14:12 L0s Exit Latency (EL0)--R/W. This field is update-able by BIOS. The default value 010b indicates that L0s exit latency is between 128 ns to less than 256 ns, assuming a commonclock configuration between the processor and the PCH. If a unique clock value is used, BIOS should update this field to 100b, indicating a L0s exit latency between 512 ns to 1 us. DMI only supports a common clock configuration. When BIOS sets this field, it must also update DMI's L0s Entry Control field at RCBA +2344h. 11:10 Active State Link PM Support (APMS)--R/W. Indicates the level of ASPM support on DMI. 00 = Reserved 01 = L0s entry supported 10 = Reserved 11 = L0s and L1 entry supported 9:4 Maximum Link Width (MLW)--RO. Indicates the link width is set to the maximum of 4 lanes. 3:0 Maximum Link Speed (MLS)--RO. The value 0001b indicates that only DMI Gen1 speed, 2.5 GT/s, is supported. The value 0010b indicates that DMI Gen2 speed, 5.0 GT/s, is supported (2.5GT/s is also supported in this setting). 337 Chipset Configuration Registers 10.1.14 LCTL--Link Control Register Offset Address: 21A8-21A9h Default Value: 0000h Bit 15:8 7 10.1.15 Attribute: Size: Description Reserved Extended Synch (ES)--R/W. When set, this bit forces extended transmission of FTS ordered sets when exiting L0s prior to entering L0 and extra TS1 sequences at exit from L1 prior to entering L0. 6:2 Reserved 1:0 Active State Link PM Control (ASPM)--R/W. Indicates whether DMI should enter L0s, L1, or both. 00 = Disabled 01 = L0s entry enabled 10 = L1 entry enabled 11 = L0s and L1 entry enabled LSTS--Link Status Register Offset Address: 21AA-21ABh Default Value: 0041h Bit 15:10 10.1.16 Attribute: Size: RO 16-bit Description Reserved 9:4 Negotiated Link Width (NLW)--RO. Negotiated link width is x4 (000100b). 3:0 Current Link Speed (LS)--RO. 0001b = 2.5 GT/s 0010b = 5.0 GT/s TCTL--TCO Configuration Register Offset Address: 3000h Default Value: 00h Bit 7 338 R/W 16-bit Attribute: Size: R/W 8-bit Description TCO IRQ Enable (IE)--R/W. 0 = TCO IRQ is disabled. 1 = TCO IRQ is enabled, as selected by the TCO_IRQ_SEL field. 6:3 Reserved 2:0 TCO IRQ Select (IS)--R/W. Specifies on which IRQ the TCO will internally appear. If not using the APIC, the TCO interrupt must be routed to IRQ9-11, and that interrupt is not sharable with the SERIRQ stream, but is shareable with other PCI interrupts. If using the APIC, the TCO interrupt can also be mapped to IRQ20-23, and can be shared with other interrupt. 000 = IRQ 9 001 = IRQ 10 010 = IRQ 11 011 = Reserved 100 = IRQ 20 (only if APIC enabled) 101 = IRQ 21 (only if APIC enabled) 110 = IRQ 22 (only if APIC enabled) 111 = IRQ 23 (only if APIC enabled) When setting the these bits, the IE bit should be cleared to prevent glitching. When the interrupt is mapped to APIC interrupts 9, 10, or 11, the APIC should be programmed for active-high reception. When the interrupt is mapped to APIC interrupts 20 through 23, the APIC should be programmed for active-low reception. Datasheet Chipset Configuration Registers 10.1.17 D31IP--Device 31 Interrupt Pin Register Offset Address: 3100-3103h Default Value: 03243200h Bit Description Reserved 27:24 Thermal Throttle Pin (TTIP)--R/W. Indicates which pin the Thermal Throttle controller drives as its interrupt. 0h = No interrupt 1h = INTA# 2h = INTB# 3h = INTC# (Default) 4h = INTD# 5h-Fh = Reserved 23:20 SATA Pin 2 (SIP2)--R/W. Indicates which pin the SATA controller 2 drives as its interrupt. 0h = No interrupt 1h = INTA# 2h = INTB# (Default) 3h = INTC# 4h = INTD# 5h-Fh = Reserved 19:16 Reserved 15:12 SMBus Pin (SMIP)--R/W. Indicates which pin the SMBus controller drives as its interrupt. 0h = No interrupt 1h = INTA# 2h = INTB# 3h = INTC# (Default) 4h = INTD# 5h-Fh = Reserved SATA Pin (SIP)--R/W. Indicates which pin the SATA controller drives as its interrupt. 0h = No interrupt 1h = INTA# 2h = INTB# (Default) 3h = INTC# 4h = INTD# 5h-Fh = Reserved 7:4 Reserved 3:0 LPC Bridge Pin (LIP)--RO. Currently, the LPC bridge does not generate an interrupt, so this field is read-only and 0h. D30IP--Device 30 Interrupt Pin Register Offset Address: 3104-3107h Default Value: 00000000h Bit 31:0 Datasheet R/W, RO 32-bit 31:28 11:8 10.1.18 Attribute: Size: Attribute: Size: RO 32-bit Description Reserved 339 Chipset Configuration Registers 10.1.19 D29IP--Device 29 Interrupt Pin Register Offset Address: 3108-310Bh Default Value: 10004321h Bit 31:4 3:0 10.1.20 Attribute: Size: Description Reserved EHCI #1 Pin (E1P)--R/W. Indicates which pin the EHCI controller #1 drives as its interrupt, if controller exists. 0h = No interrupt 1h = INTA# (Default) 2h = INTB# 3h = INTC# 4h = INTD# 5h-7h = Reserved Note: EHCI Controller #1 is mapped to Device 29 Function 0. D28IP--Device 28 Interrupt Pin Register Offset Address: 310C-310Fh Default Value: 00214321h 340 R/W 32-bit Attribute: Size: R/W 32-bit Bit Description 31:28 PCI Express* #8 Pin (P8IP)--R/W. Indicates which pin the PCI Express* port #8 drives as its interrupt. 0h = No interrupt 1h = INTA# 2h = INTB# 3h = INTC# 4h = INTD# (Default) 5h-7h = Reserved 27:24 PCI Express #7 Pin (P7IP)--R/W. Indicates which pin the PCI Express port #7 drives as its interrupt. 0h = No interrupt 1h = INTA# 2h = INTB# 3h = INTC# (Default) 4h = INTD# 5h-7h = Reserved 23:20 PCI Express* #6 Pin (P6IP)--R/W. Indicates which pin the PCI Express* port #6 drives as its interrupt. 0h = No interrupt 1h = INTA# 2h = INTB# (Default) 3h = INTC# 4h = INTD# 5h-7h = Reserved 19:16 PCI Express #5 Pin (P5IP)--R/W. Indicates which pin the PCI Express port #5 drives as its interrupt. 0h = No interrupt 1h = INTA# (Default) 2h = INTB# 3h = INTC# 4h = INTD# 5h-7h = Reserved Datasheet Chipset Configuration Registers Bit 15:12 10.1.21 Description PCI Express #4 Pin (P4IP)--R/W. Indicates which pin the PCI Express* port #4 drives as its interrupt. 0h = No interrupt 1h = INTA# 2h = INTB# 3h = INTC# 4h = INTD# (Default) 5h-7h = Reserved 11:8 PCI Express #3 Pin (P3IP)--R/W. Indicates which pin the PCI Express port #3 drives as its interrupt. 0h = No interrupt 1h = INTA# 2h = INTB# 3h = INTC# (Default) 4h = INTD# 5h-7h = Reserved 7:4 PCI Express #2 Pin (P2IP)--R/W. Indicates which pin the PCI Express port #2 drives as its interrupt. 0h = No interrupt 1h = INTA# 2h = INTB# (Default) 3h = INTC# 4h = INTD# 5h-7h = Reserved 3:0 PCI Express #1 Pin (P1IP)--R/W. Indicates which pin the PCI Express port #1 drives as its interrupt. 0h = No interrupt 1h = INTA# (Default) 2h = INTB# 3h = INTC# 4h = INTD# 5h-7h = Reserved D27IP--Device 27 Interrupt Pin Register Offset Address: 3110-3113h Default Value: 00000001h Bit 31:4 3:0 Datasheet Attribute: Size: R/W 32-bit Description Reserved Intel(R) High Definition Audio Pin (ZIP)--R/W. Indicates which pin the Intel High Definition Audio controller drives as its interrupt. 0h = No interrupt 1h = INTA# (Default) 2h = INTB# 3h = INTC# 4h = INTD# 5h-Fh = Reserved 341 Chipset Configuration Registers 10.1.22 D26IP--Device 26 Interrupt Pin Register Offset Address: 3114-3117h Default Value: 30000321h Bit 31:4 3:0 10.1.23 Attribute: Size: Description Reserved EHCI #2 Pin (E2P)--R/W. Indicates which pin EHCI controller #2 drives as its interrupt, if controller exists. 0h = No Interrupt 1h = INTA# (Default) 2h = INTB# 3h = INTC# 4h = INTD# 5h-Fh = Reserve Note: EHCI Controller #2 is mapped to Device 26 Function 0. D25IP--Device 25 Interrupt Pin Register Offset Address: 3118-311Bh Default Value: 00000001h Bit 31:4 3:0 10.1.24 Attribute: Size: R/W 32-bit Description Reserved GbE LAN Pin (LIP)--R/W. Indicates which pin the internal GbE LAN controller drives as its interrupt 0h = No Interrupt 1h = INTA# (Default) 2h = INTB# 3h = INTC# 4h = INTD# 5h-Fh = Reserved D22IP--Device 22 Interrupt Pin Register Offset Address: 3124-3127h Default Value: 00004321h Bit Attribute: Size: R/W 32-bit Description 31:16 Reserved 15:12 KT Pin (KTIP)--R/W. Indicates which pin the Keyboard text PCI functionality drives as its interrupt 0h = No Interrupt 1h = INTA# 2h = INTB# 3h = INTC# 4h = INTD# (Default) 5h-Fh = Reserved 11:8 342 R/W 32-bit IDE-R Pin (IDERIP)--R/W. Indicates which pin the IDE Redirect PCI functionality drives as its interrupt 0h = No Interrupt 1h = INTA# 2h = INTB# 3h = INTC# (Default) 4h = INTD# 5h-Fh = Reserved Datasheet Chipset Configuration Registers Bit 10.1.25 Description Intel(R) 7:4 MEI #2 Pin (MEI2IP)--R/W. Indicates which pin the Management Engine Interface #2 drives as its interrupt 0h = No Interrupt 1h = INTA# 2h = INTB# (Default) 3h = INTC# 4h = INTD# 5h-Fh = Reserved 3:0 Intel(R) MEI #1 Pin (MEI1IP)--R/W. Indicates which pin the Management Engine Interface controller #1 drives as its interrupt 0h = No Interrupt 1h = INTA# (Default) 2h = INTB# 3h = INTC# 4h = INTD# 5h-Fh = Reserved D20IP--Device 20 Interrupt Pin Register Offset Address: 3128-312bh Default Value: 00000021h Bit 31:4 3:0 10.1.26 Attribute: Size: Description Reserved xHCI Pin (XHCIIP)--R/W. Indicates which pin the xHCI drives as its interrupt 0h = No Interrupt 1h = INTA# (Default) 2h = INTB# 3h = INTC# 4h = INTD# 5h-Fh = Reserved D31IR--Device 31 Interrupt Route Register Offset Address: 3140-3141h Default Value: 3210h Bit 15 14:12 11 10:8 Datasheet R/W 32-bit Attribute: Size: R/W 16-bit Description Reserved Interrupt D Pin Route (IDR)--R/W. Indicates which physical pin on the PCH is connected to the INTD# pin reported for device 31 functions. 0h = PIRQA# 1h = PIRQB# 2h = PIRQC# 3h = PIRQD# (Default) 4h = PIRQE# 5h = PIRQF# 6h = PIRQG# 7h = PIRQH# Reserved Interrupt C Pin Route (ICR)--R/W. Indicates which physical pin on the PCH is connected to the INTC# pin reported for device 31 functions. 0h = PIRQA# 1h = PIRQB# 2h = PIRQC# (Default) 3h = PIRQD# 4h = PIRQE# 5h = PIRQF# 6h = PIRQG# 7h = PIRQH# 343 Chipset Configuration Registers Bit 7 6:4 3 2:0 10.1.27 Description Reserved Interrupt B Pin Route (IBR)--R/W. Indicates which physical pin on the PCH is connected to the INTB# pin reported for device 31 functions. 0h = PIRQA# 1h = PIRQB# (Default) 2h = PIRQC# 3h = PIRQD# 4h = PIRQE# 5h = PIRQF# 6h = PIRQG# 7h = PIRQH# Reserved Interrupt A Pin Route (IAR)--R/W. Indicates which physical pin on the PCH is connected to the INTA# pin reported for device 31 functions. 0h = PIRQA# (Default) 1h = PIRQB# 2h = PIRQC# 3h = PIRQD# 4h = PIRQE# 5h = PIRQF# 6h = PIRQG# 7h = PIRQH# D30IR--Device 30 Interrupt Route Register Offset Address: 3142-3143h Default Value: 0000h Bit 15:0 10.1.28 Attribute: Size: Description Reserved. No interrupts generated from Device 30. D29IR--Device 29 Interrupt Route Register Offset Address: 3144-3145h Default Value: 3210h Bit 15 14:12 11 10:8 7 344 RO 16-bit Attribute: Size: R/W 16-bit Description Reserved Interrupt D Pin Route (IDR)--R/W. Indicates which physical pin on the PCH is connected to the INTD# pin reported for device 29 functions. 0h = PIRQA# 1h = PIRQB# 2h = PIRQC# 3h = PIRQD# (Default) 4h = PIRQE# 5h = PIRQF# 6h = PIRQG# 7h = PIRQH# Reserved Interrupt C Pin Route (ICR)--R/W. Indicates which physical pin on the PCH is connected to the INTC# pin reported for device 29 functions. 0h = PIRQA# 1h = PIRQB# 2h = PIRQC# (Default) 3h = PIRQD# 4h = PIRQE# 5h = PIRQF# 6h = PIRQG# 7h = PIRQH# Reserved Datasheet Chipset Configuration Registers Bit Description 6:4 Interrupt B Pin Route (IBR)--R/W. Indicates which physical pin on the PCH is connected to the INTB# pin reported for device 29 functions. 0h = PIRQA# 1h = PIRQB# (Default) 2h = PIRQC# 3h = PIRQD# 4h = PIRQE# 5h = PIRQF# 6h = PIRQG# 7h = PIRQH# 3 2:0 10.1.29 Reserved Interrupt A Pin Route (IAR)--R/W. Indicates which physical pin on the PCH is connected to the INTA# pin reported for device 29 functions. 0h = PIRQA# (Default) 1h = PIRQB# 2h = PIRQC# 3h = PIRQD# 4h = PIRQE# 5h = PIRQF# 6h = PIRQG# 7h = PIRQH# D28IR--Device 28 Interrupt Route Register Offset Address: 3146-3147h Default Value: 3210h Bit 15 14:12 11 10:8 7 6:4 3 Datasheet Attribute: Size: R/W 16-bit Description Reserved Interrupt D Pin Route (IDR)--R/W. Indicates which physical pin on the PCH is connected to the INTD# pin reported for device 28 functions. 0h = PIRQA# 1h = PIRQB# 2h = PIRQC# 3h = PIRQD# (Default) 4h = PIRQE# 5h = PIRQF# 6h = PIRQG# 7h = PIRQH# Reserved Interrupt C Pin Route (ICR)--R/W. Indicates which physical pin on the PCH is connected to the INTC# pin reported for device 28 functions. 0h = PIRQA# 1h = PIRQB# 2h = PIRQC# (Default) 3h = PIRQD# 4h = PIRQE# 5h = PIRQF# 6h = PIRQG# 7h = PIRQH# Reserved Interrupt B Pin Route (IBR)--R/W. Indicates which physical pin on the PCH is connected to the INTB# pin reported for device 28 functions. 0h = PIRQA# 1h = PIRQB# (Default) 2h = PIRQC# 3h = PIRQD# 4h = PIRQE# 5h = PIRQF# 6h = PIRQG# 7h = PIRQH# Reserved 345 Chipset Configuration Registers 10.1.30 Bit Description 2:0 Interrupt A Pin Route (IAR)--R/W. Indicates which physical pin on the PCH is connected to the INTA# pin reported for device 28 functions. 0h = PIRQA# (Default) 1h = PIRQB# 2h = PIRQC# 3h = PIRQD# 4h = PIRQE# 5h = PIRQF# 6h = PIRQG# 7h = PIRQH# D27IR--Device 27 Interrupt Route Register Offset Address: 3148-3149h Default Value: 3210h Bit 15 14:12 11 10:8 7 6:4 3 2:0 346 Attribute: Size: R/W 16-bit Description Reserved Interrupt D Pin Route (IDR)--R/W. Indicates which physical pin on the PCH is connected to the INTD# pin reported for device 27 functions. 0h = PIRQA# 1h = PIRQB# 2h = PIRQC# 3h = PIRQD# (Default) 4h = PIRQE# 5h = PIRQF# 6h = PIRQG# 7h = PIRQH# Reserved Interrupt C Pin Route (ICR)--R/W. Indicates which physical pin on the PCH is connected to the INTC# pin reported for device 27 functions. 0h = PIRQA# 1h = PIRQB# 2h = PIRQC# (Default) 3h = PIRQD# 4h = PIRQE# 5h = PIRQF# 6h = PIRQG# 7h = PIRQH# Reserved Interrupt B Pin Route (IBR)--R/W. Indicates which physical pin on the PCH is connected to the INTB# pin reported for device 27 functions. 0h = PIRQA# 1h = PIRQB# (Default) 2h = PIRQC# 3h = PIRQD# 4h = PIRQE# 5h = PIRQF# 6h = PIRQG# 7h = PIRQH# Reserved Interrupt A Pin Route (IAR)--R/W. Indicates which physical pin on the PCH is connected to the INTA# pin reported for device 27 functions. 0h = PIRQA# (Default) 1h = PIRQB# 2h = PIRQC# 3h = PIRQD# 4h = PIRQE# 5h = PIRQF# 6h = PIRQG# 7h = PIRQH# Datasheet Chipset Configuration Registers 10.1.31 D26IR--Device 26 Interrupt Route Register Offset Address: 314C-314Dh Default Value: 3210h Bit 15 14:12 11 10:8 7 6:4 3 2:0 Datasheet Attribute: Size: R/W 16-bit Description Reserved Interrupt D Pin Route (IDR)--R/W. Indicates which physical pin on the PCH is connected to the INTD# pin reported for device 26 functions: 0h = PIRQA# 1h = PIRQB# 2h = PIRQC# 3h = PIRQD# (Default) 4h = PIRQE# 5h = PIRQF# 6h = PIRQG# 7h = PIRQH# Reserved Interrupt C Pin Route (ICR)--R/W. Indicates which physical pin on the PCH is connected to the INTC# pin reported for device 26 functions. 0h = PIRQA# 1h = PIRQB# 2h = PIRQC# (Default) 3h = PIRQD# 4h = PIRQE# 5h = PIRQF# 6h = PIRQG# 7h = PIRQH# Reserved Interrupt B Pin Route (IBR)--R/W. Indicates which physical pin on the PCH is connected to the INTB# pin reported for device 26 functions. 0h = PIRQA# 1h = PIRQB# (Default) 2h = PIRQC# 3h = PIRQD# 4h = PIRQE# 5h = PIRQF# 6h = PIRQG# 7h = PIRQH# Reserved Interrupt A Pin Route (IAR)--R/W. Indicates which physical pin on the PCH is connected to the INTA# pin reported for device 26 functions. 0h = PIRQA# (Default) 1h = PIRQB# 2h = PIRQC# 3h = PIRQD# 4h = PIRQE# 5h = PIRQF# 6h = PIRQG# 7h = PIRQH# 347 Chipset Configuration Registers 10.1.32 D25IR--Device 25 Interrupt Route Register Offset Address: 3150-3151h Default Value: 3210h Bit 15 14:12 11 10:8 7 6:4 3 2:0 348 Attribute: Size: R/W 16-bit Description Reserved Interrupt D Pin Route (IDR):--R/W. Indicates which physical pin on the PCH is connected to the INTD# pin reported for device 25 functions: 0h = PIRQA# 1h = PIRQB# 2h = PIRQC# 3h = PIRQD# (Default) 4h = PIRQE# 5h = PIRQF# 6h = PIRQG# 7h = PIRQH# Reserved Interrupt C Pin Route (ICR)--R/W. Indicates which physical pin on the PCH is connected to the INTC# pin reported for device 25 functions. 0h = PIRQA# 1h = PIRQB# 2h = PIRQC# (Default) 3h = PIRQD# 4h = PIRQE# 5h = PIRQF# 6h = PIRQG# 7h = PIRQH# Reserved Interrupt B Pin Route (IBR)--R/W. Indicates which physical pin on the PCH is connected to the INTB# pin reported for device 25 functions. 0h = PIRQA# 1h = PIRQB# (Default) 2h = PIRQC# 3h = PIRQD# 4h = PIRQE# 5h = PIRQF# 6h = PIRQG# 7h = PIRQH# Reserved Interrupt A Pin Route (IAR)--R/W. Indicates which physical pin on the PCH is connected to the INTA# pin reported for device 25 functions. 0h = PIRQA# (Default) 1h = PIRQB# 2h = PIRQC# 3h = PIRQD# 4h = PIRQE# 5h = PIRQF# 6h = PIRQG# 7h = PIRQH# Datasheet Chipset Configuration Registers 10.1.33 D22IR--Device 22 Interrupt Route Register Offset Address: 315C-315Dh Default Value: 3210h Bit 15 14:12 11 10:8 7 6:4 3 2:0 Datasheet Attribute: Size: R/W 16-bit Description Reserved Interrupt D Pin Route (IDR):--R/W. Indicates which physical pin on the PCH is connected to the INTD# pin reported for device 22 functions: 0h = PIRQA# 1h = PIRQB# 2h = PIRQC# 3h = PIRQD# (Default) 4h = PIRQE# 5h = PIRQF# 6h = PIRQG# 7h = PIRQH# Reserved Interrupt C Pin Route (ICR)--R/W. Indicates which physical pin on the PCH is connected to the INTC# pin reported for device 22 functions. 0h = PIRQA# 1h = PIRQB# 2h = PIRQC# (Default) 3h = PIRQD# 4h = PIRQE# 5h = PIRQF# 6h = PIRQG# 7h = PIRQH# Reserved Interrupt B Pin Route (IBR)--R/W. Indicates which physical pin on the PCH is connected to the INTB# pin reported for device 22 functions. 0h = PIRQA# 1h = PIRQB# (Default) 2h = PIRQC# 3h = PIRQD# 4h = PIRQE# 5h = PIRQF# 6h = PIRQG# 7h = PIRQH# Reserved Interrupt A Pin Route (IAR)--R/W. Indicates which physical pin on the PCH is connected to the INTA# pin reported for device 22 functions. 0h = PIRQA# (Default) 1h = PIRQB# 2h = PIRQC# 3h = PIRQD# 4h = PIRQE# 5h = PIRQF# 6h = PIRQG# 7h = PIRQH# 349 Chipset Configuration Registers 10.1.34 D20IR--Device 20 Interrupt Route Register Offset Address: 3160-3161h Default Value: 3210h Bit 15 14:12 11 10:8 7 6:4 3 2:0 350 Attribute: Size: R/W 16-bit Description Reserved Interrupt D Pin Route (IDR)--R/W. Indicates which physical pin on the PCH is connected to the INTD# pin reported for device 20 functions: 0h = PIRQA# 1h = PIRQB# 2h = PIRQC# 3h = PIRQD# (Default) 4h = PIRQE# 5h = PIRQF# 6h = PIRQG# 7h = PIRQH# Reserved Interrupt C Pin Route (ICR)--R/W. Indicates which physical pin on the PCH is connected to the INTC# pin reported for device 20 functions. 0h = PIRQA# 1h = PIRQB# 2h = PIRQC# (Default) 3h = PIRQD# 4h = PIRQE# 5h = PIRQF# 6h = PIRQG# 7h = PIRQH# Reserved Interrupt B Pin Route (IBR)--R/W. Indicates which physical pin on the PCH is connected to the INTB# pin reported for device 20 functions. 0h = PIRQA# 1h = PIRQB# (Default) 2h = PIRQC# 3h = PIRQD# 4h = PIRQE# 5h = PIRQF# 6h = PIRQG# 7h = PIRQH# Reserved Interrupt A Pin Route (IAR)--R/W. Indicates which physical pin on the PCH is connected to the INTA# pin reported for device 20 functions. 0h = PIRQA# (Default) 1h = PIRQB# 2h = PIRQC# 3h = PIRQD# 4h = PIRQE# 5h = PIRQF# 6h = PIRQG# 7h = PIRQH# Datasheet Chipset Configuration Registers 10.1.35 OIC--Other Interrupt Control Register Offset Address: 31FE-31FFh Default Value: 0000h Bit Reserved 9 Coprocessor Error Enable (CEN)--R/W. 0 = FERR# will not generate IRQ13 nor IGNNE#. 1 = If FERR# is low, the PCH generates IRQ13 internally and holds it until an I/O port F0h write. It will also drive IGNNE# active. 8 APIC Enable (AEN)--R/W. 0 = The internal IOxAPIC is disabled. 1 = Enables the internal IOxAPIC and its address decode. Note: Software should read this register after modifying APIC enable bit prior to access to the IOxAPIC address range. 7:0 APIC Range Select (ASEL)--R/W. These bits define address bits 19:12 for the IOxAPIC range. The default value of 00h enables compatibility with prior PCH products as an initial value. This value must not be changed unless the IOxAPIC Enable bit is cleared. Note: FEC1_0000h-FEC3_FFFFh is allocated to PCIe when I/OxAPIC Enable (PAE) bit is set. WADT_AC--Wake Alarm Device Timer - AC Register Offset Address: 3300-3303h Default Value: FFFFFFFFh Bit 31:0 10.1.37 Attribute: Size: R/W 32-bit Description Wake Alarm Device Timer Value for AC Mode (WADT_AC_VAL): R/W. This field contains the 32-bit wake alarm device timer value (1 second granularity) for AC power. The timer begins decrementing when written to a value other than FFFFFFFFh (regardless of the power source when the write occurs). Upon counting down to 0: * If on AC power, GPE0_STS.WADT_STS will be set. This status bit being set will generate a host wake if GPE0_EN.WADT_EN is `1'. * If power source is DC at this time, the status bit is not set. However, if AC power subsequently returns to the platform, the AC Expired Timer begins running. Refer to WADT_EXP_AC for more details. * The timer returns to its default value of FFFFFFFFh. WADT_DC--Wake Alarm Device Timer - DC Register Offset Address: 3304-3307h Default Value: FFFFFFFFh Bit 31:0 Attribute: Size: R/W 32-bit Description Wake Alarm Device Timer Value for DC Mode (WADT_DC_VAL): R/W. This field contains the 32-bit wake alarm device timer value (1 second granularity) for DC power. The timer begins decrementing when written to a value other than FFFFFFFFh (regardless of the power source when the write occurs). Upon counting down to 0: * If on DC power, GPE0_STS.WADT_STS will be set. This status bit being set will generate a host wake if GPE0_EN.WADT_EN is `1'. * If power source is AC at this time, the status bit is not set. However, if DC power subsequently returns to the platform, the DC Expired Timer begins running. Refer to WADT_EXP_DC for more details. * The timer returns to its default value of FFFFFFFFh. Note: Datasheet R/W 16-bit Description 15:10 10.1.36 Attribute: Size: Bits in this register only need to be valid for reading when the Main power well is up. 351 Chipset Configuration Registers 10.1.38 WADT_EXP_AC--Wake Alarm Device Expired Timer - AC Register Offset Address: 3308-330Bh Default Value: FFFFFFFFh Description 31:0 Wake Alarm Device Expired Timer Value for AC Mode (WADT_EXP_AC_VAL): R/W. This field contains the 32-bit wake alarm device "Expired Timer" value (1 second granularity) for AC power. The timer begins decrementing after switching from DC to AC power, in the case where the WADT_AC timer has already expired while platform was on DC power. This timer only decrements while operating on AC power. So if the power source switches back to DC power, the timer will stop (but not reset). When AC power returns, the timer will again begin decrementing. Upon expiration of this timer: * If on AC power, GPE0_STS.WADT_STS will be set. This status bit being set will generate a host wake if GPE0_EN.WADT_EN is `1'. * Both the AC and DC Expired TImers return to their default value of FFFFFFFFh. Note: This timer will only begin decrementing under the conditions described above if this field has been configured for something other than its default value of FFFFFFFFh. Bits in this register only need to be valid for reading when the Main power well is up. WADT_EXP_DC--Wake Alarm Device Expired Timer - DC Register Offset Address: 330C-330Fh Default Value: FFFFFFFFh 10.1.40 Attribute: Size: R/W 32-bit Bit Description 31:0 Wake Alarm Device Expired Timer Value for DC Mode (WADT_EXP_DC_VAL): R/W. This field contains the 32-bit wake alarm device "Expired Timer" value (1 second granularity) for DC power. The timer begins decrementing after switching from AC to DC power, in the case where the WADT_DC timer has already expired while platform was on AC power. This timer only decrements while operating on DC power. So if the power source switches back to AC power, the timer will stop (but not reset). When DC power returns, the timer will again begin decrementing. Upon expiration of this timer: * If on DC power, GPE0_STS.WADT_STS will be set. This status bit being set will generate a host wake if GPE0_EN.WADT_EN is `1'. * Both the AC and DC Expired TImers return to their default value of FFFFFFFFh. Note: This timer will only begin decrementing under the conditions described above if this field has been configured for something other than its default value of FFFFFFFF. Note: Bits in this register only need to be valid for reading when the Main power well is up. PRSTS--Power and Reset Status Register Offset Address: 3310-3313h Default Value: 05000000h Bit 31:16 15 14:7 6 352 R/W 32-bit Bit Note: 10.1.39 Attribute: Size: Attribute: Size: RO, R/WC 32-bit Description Reserved Power Management Watchdog Timer--R/WC. This bit is set when the Power Management watchdog timer causes a global reset. This bit is cleared when the software writes it with a 1b. Reserved Intel(R) Management Engine Watchdog Timer Status--R/WC. This bit is set when the Intel Management Engine watchdog timer causes a global reset. This bit is cleared when the software writes it with a 1b. Datasheet Chipset Configuration Registers Bit 10.1.41 Description 5 Wake On LAN Override Wake Status (WOL_OVR_WK_STS)--R/WC. This bit gets set when all of the following conditions are met: * Integrated LAN Signals a Power Management Event * The system is not in S0 * The "WoL Enable Override" bit is set in configuration space. BIOS can read this status bit to determine this wake source. Software clears this bit by writing a 1 to it. 4 PRSTS Field 1--R/WC. BIOS may program this field. 3 Intel ME Host Power Down (ME_HOST_PWRDN)--R/WC. This bit is set when the Intel Management Engine generates a host reset with power down. 2 Intel ME Host Reset Warm Status (ME_HRST_WARM_STS)--R/WC. This bit is set when the Intel Management Engine generates a Host reset without power cycling. Software clears this bit by writing a 1 to this bit position. 1 Intel ME Host Reset Cold Status (ME_HRST_COLD_STS)--R/WC. This bit is set when the Intel Management Engine generates a Host reset with power cycling. Software clears this bit by writing a 1 to this bit position. 0 Intel ME WAKE STATUS (ME_WAKE_STS)--R/WC. This bit is set when the Intel Management Engine generates a Non-Maskable wake event, and is not affected by any other enable bit. When this bit is set, the Host Power Management logic wakes to S0. PM_CFG--Power Management Configuration Register Offset Address: 3318-331Bh Default Value: 00000020h Bit R/W 32-bit Description 31:27 Reserved 26:24 PM_CFG Field 1--R/W. BIOS must program this field to 101b. 23:22 Datasheet Attribute: Size: Reserved 21 RTC Wake from Deep Sx Disable (RTC_DS_WAKE_DIS)--R/W. When set, this bit disables RTC wakes from waking the system from Deep Sx. This bit is reset by RTCRST#. 20 After G3 Last State Enable (AG3_LS_EN) -- R/W. When GEN_PMCON_3.AFTERG3_EN is "0", AG3_LS_EN determines whether the PCH will consider the platform's previous state when determining whether to power-up after G3. 0 = PCH power-up policies after G3 do not depend on the platform's state when the G3 occurred. 1 = PCH power-up policies after G3 depend on the platform's state when the G3 occurred. -- If the power failure occurred while the platform was in S0, the platform will power-up to S0 upon existing G3. -- If the power failure occurred while the platform was in Sx, the platform will stay in Sx upon existing G3. Note: This bit applies only when GEN_PMCON_3.AFTERG3_EN is "0". If AFTERG3_EN is "1", the platform will always stay in Sx after G3 regardless of the value of AG3_LS_EN. 353 Chipset Configuration Registers 354 Bit Description 19:18 SLP_SUS# Minimum Assertion Width (SLP_SUS_MIN_ASST_WDTH)--R/WL. This field indicates the minimum assertion width of the SLP_SUS# signal to ensure that the SUS power supplies have been fully power cycled. This value may be modified per platform depending on power supply capacitance, board capacitance, power circuits, and so on. Valid values are: 11 = 4 seconds 10 = 1 second 01 = 500 ms 00 = 0 ms (that is, stretching disabled - default) These bits are cleared by RTCRST# assertion. Notes: 1. This field is RO when the SLP Stretching Policy Lock-Down bit is set. 2. This field is ignored when exiting G3 or Deep Sx states if the "Disable SLP Stretching After SUS Well Power Up" bit is set. Unlike with all other SLP_* pin stretching, this disable bit only impacts SLP_SUS# stretching during G3 exit, rather than both G3 and Deep Sx exit. SLP_SUS# stretching always applies to Deep Sx regardless of the disable bit. 3. For platforms that enable Deep Sx, BIOS must program SLP_SUS# stretching to be greater than or equal to the largest stretching value on any other SLP_* pin (SLP_S3#, SLP_S4#, SLP_LAN# or SLP_A#). 17:16 SLP_A# Minimum Assertion Width (SLP_A_MIN_ASST_WDTH)--R/W. This field indicates the minimum assertion width of the SLP_A# signal to ensure that the ASW power supplies have been fully power cycled. This value may be modified per platform depending on power supply capacitance, board capacitance, power circuits, and so on. Valid values are: 11 = 2 seconds 10 = 98 ms 01 = 4 seconds 00 = 0 ms (that is, stretching disabled - default) These bits are cleared by RTCRST# assertion. Notes: 1. This field is RO when the SLP Stretching Policy Lock-Down bit is set. 2. This field is ignored when exiting G3 or Deep Sx states if the "Disable SLP Stretching After SUS Well Power Up" bit is set. 15:14 SLP_LAN# Minimum Assertion Width (SLP_LAN_MIN_ASST_WDTH)--R/WL. This field indicates the minimum assertion width of the SLP_LAN# signal to ensure that the PHY power supplies have been fully power cycled. This value may be modified per platform depending on power supply capacitance, board capacitance, power circuits, and so on. Valid values are: 11 = 2 seconds 10 = 50 ms 01 = 1 ms 00 = 0 ms (that is, stretching disabled - default) These bits are cleared by RTCRST# assertion. Note: This field is RO when the SLP Stretching Policy Lock-Down bit is set. 13:10 Reserved 9:8 Reset Power Cycle Duration (PWR_CYC_DUR)--R/WL. This field indicates the minimum time a platform will stay in reset (SLP_S3#, SLP_S4#, SLP_S5# asserted and SLP_A# and SLP_LAN# asserted if applicable) during a host reset with power cycle, host reset with power down or a global reset. The duration programmed in this register takes precedence over the applicable SLP_# stretch timers in these reset scenario. Valid values are: 11 = 1-2 seconds 10 = 2-3 seconds 01 = 3-4 seconds 00 = 4-5 seconds (default) These bits are cleared by RTCRST# assertion. Notes: 1. This field is RO when the SLP Stretching Policy Lock-Down bit is set. 2. The duration programmed in this register should never be smaller than the stretch duration programmed in the following registers: -- GEN_PMCON_3.SLP_S3_MIN_ASST_WDTH -- GEN_PMCON_3.SLP_S4_MIN_ASST_WDTH -- PM_CFG.SLP_A_MIN_ASST_WDTH -- PM_CFG.SLP_LAN_MIN_ASST_WDTH 7:5 Reserved Datasheet Chipset Configuration Registers Bit 4 3:0 10.1.42 Description Host Wireless LAN PHY Power Enable (HOST_WLAN_PP_EN)--R/W. Set by host software when it desires the Wi-Fi LAN PHY to be powered in Sx power states for Wake Over Wi-Fi (WoWLAN). See SLP_WLAN# for more information. Default = 0b. Reserved DEEP_S3_POL--Deep Sx From S3 Power Policies Register Offset Address: 3328-332Bh Default Value: 00000000h Attribute: Size: R/W 32-bit This register is in the RTC power well and is reset by RTCRST# assertion. Bit 31:2 10.1.43 Description Reserved 1 Deep Sx From S3 Enable in DC Mode (DPS3_EN_DC)--R/W. A '1' in this bit enables the platform to enter Deep Sx while operating in S3 on DC power (based on the ACPRESENT pin value). 0 Deep Sx From S3 Enable in AC Mode (DPS3_EN_AC)--R/W. A '1' in this bit enables the platform to enter Deep Sx while operating in S3 on AC power (based on the ACPRESENT pin value). DEEP_S4_POL--Deep Sx From S4 Power Policies Register Offset Address: 332C-332Fh Default Value: 00000000h Attribute: Size: R/W 32-bit This register is in the RTC power well and is reset by RTCRST# assertion. Bit 31:2 10.1.44 Description Reserved 1 Deep Sx From S4 Enable in DC Mode (DPS4_EN_DC)--R/W. A '1' in this bit enables the platform to enter Deep Sx while operating in S4 on DC power (based on the ACPRESENT pin value). 0 Deep Sx From S4 Enable in AC Mode (DPS4_EN_AC)--R/W. A '1' in this bit enables the platform to enter Deep Sx while operating in S4 on AC power (based on the ACPRESENT pin value). Required to be programmed to 0 on mobile. DEEP_S5_POL--Deep Sx From S5 Power Policies Register Offset Address: 3330-3333h Default Value: 00000000h Attribute: Size: R/W 32-bit This register is in the RTC power well and is reset by RTCRST# assertion. Bit 31:16 Reserved 15 Deep Sx From S5 Enable in DC Mode (DPS5_EN_DC)--R/W. A '1' in this bit enables the platform to enter Deep Sx while operating in S5 on DC power (based on the ACPRESENT pin value). 14 Deep Sx From S5 Enable in AC Mode (DPS5_EN_AC)--R/W. A '1' in this bit enables the platform to enter Deep Sx while operating in S5 on AC power (based on the ACPRESENT pin value). 13:0 Datasheet Description Reserved 355 Chipset Configuration Registers 10.1.45 DSX_CFG--Deep Sx Configuration Register Offset Address: 3334-3337h Default Value: 00000000h Attribute: Size: R/W 32-bit This register is in the RTC power well and is reset by RTCRST# assertion. Bit 31:3 2 Description Reserved WAKE# Pin Deep Sx Enable (WAKE_PIN__DSX_EN)--R/W. When this bit is `1', the PCI Express* WAKE# pin is monitored while in Deep Sx, supporting wake from Deep Sx due to assertion of this pin. In this case the platform must externally pull-up the pin to the DSW (instead of pulling-up to the SUS as historically been the case). When this bit is `0': * Deep Sx configurations: The PCH internal pull-down on the WAKE# pin is enabled in Deep Sx and during G3 exit and the pin is not monitored during this time. * Deep Sx disabled configurations: The PCH internal pull-down on the WAKE# pin is never enabled. Note: 1 ACPRESENT Pin Pull-down in Deep Sx Disable (ACPRE_PD_DSX_DIS)--R/W. When this bit is `1', the internal pull-down on this ACPRESENT pin is disabled. However, the pull-down is not necessarily enabled if the bit is `0'. To support ME wakes from Deep Sx using MGPIO2, the pin is always monitored regardless of the value of this host policy bit. When this bit is `0': * Deep Sx configurations: The PCH internal pull-down on ACPRESENT is enabled in Deep Sx and during G3 exit. * Deep Sx disabled configurations: The PCH internal pull-down on ACPRESENT is always disabled. Note: 0 Deep Sx disabled configuration must leave this bit at `0' and the pull-down is disabled even though the bit is `0'. GP27 Pin Deep Sx Enable (GP27_PIN_DSX_EN)--R/W. When this bit is `1', the GP27 pin is monitored while in Deep Sx, supporting wake from Deep Sx due to assertion of this pin. In this case the platform must drive the pin to the correct value while in Deep Sx. When this bit is `0': * Deep Sx configurations: The PCH internal pull-down on GP27 pin is enabled in Deep Sx and during G3 exit and the pin is not monitored during this time. * Deep Sx disabled configurations: The PCH internal pull-down on GP27 pin is never enabled. Note: 10.1.46 Deep Sx disabled configuration must leave this bit at `0'. Deep Sx disabled configuration must leave this bit at `0'. PMSYNC_CFG--PMSYNC Configuration Offset Address: 33C8-33CBh Default Value: 00000000h Bit 31:12 356 Attribute: Size: R/W 32-bit Description Reserved 11 GPIO_D Pin Selection (GPIO_D_SEL)--R/W. There are two possible GPIOs that can be routed to the GPIO_D PMSYNC state. This bit selects between them: 0 = GPIO5 (default) 1 = GPIO0 10 GPIO_C Pin Selection (GPIO_C_SEL)--R/W. There are two possible GPIOs that can be routed to the GPIO_C PMSYNC state. This bit selects between them: 0 = GPIO37 (default) 1 = GPIO4 Datasheet Chipset Configuration Registers Bit Description 9 GPIO_B Pin Selection (GPIO_B_SEL)--R/W. There are two possible GPIOs that can be routed to the GPIO_B PMSYNC state. This bit selects between them: 0 = GPIO0 (default) 1 = GPIO37 8 GPIO_A Pin Selection (GPIO_A_SEL)--R/W. There are two possible GPIOs that can be routed to the GPIO_A PMSYNC state. This bit selects between them: 0 = GPIO4 (default) 1 = GPIO5 7:0 10.1.47 Reserved RC--RTC Configuration Register Offset Address: 3400-3403h Default Value: 00000000h Bit 31:5 Description Reserved Upper 128 Byte Lock (UL)--R/WLO. 0 = Bytes not locked. 1 = Bytes 38h-3Fh in the upper 128-byte bank of RTC RAM are locked and cannot be accessed. Writes will be dropped and reads will not return any ensured data. Bit reset on system reset. 3 Lower 128 Byte Lock (LL)--R/WLO. 0 = Bytes not locked. 1 = Bytes 38h-3Fh in the lower 128-byte bank of RTC RAM are locked and cannot be accessed. Writes will be dropped and reads will not return any ensured data. Bit reset on system reset. 2 Upper 128 Byte Enable (UE)--R/W. 0 = Bytes locked. 1 = The upper 128-byte bank of RTC RAM can be accessed. Reserved HPTC--High Precision Timer Configuration Register Offset Address: 3404-3407h Default Value: 00000000h Bit 31:8 7 Datasheet R/W, R/WLO 32-bit 4 1:0 10.1.48 Attribute: Size: Attribute: Size: R/W 32-bit Description Reserved Address Enable (AE)--R/W. 0 = Address disabled. 1 = The PCH will decode the High Precision Timer memory address range selected by bits 1:0 below. 6:2 Reserved 1:0 Address Select (AS)--R/W. This 2-bit field selects 1 of 4 possible memory address ranges for the High Precision Timer functionality. The encodings are: 00 = FED0_0000h - FED0_03FFh 01 = FED0_1000h - FED0_13FFh 10 = FED0_2000h - FED0_23FFh 11 = FED0_3000h - FED0_33FFh 357 Chipset Configuration Registers 10.1.49 GCS--General Control and Status Register Offset Address: 3410-3413h Default Value: 00000yy0h (yy = xx0000x0b) Bit Attribute: Size: R/W, R/WLO 32-bit Description 31:12 Reserved 11:10 Boot BIOS Straps (BBS)--R/W. This field determines the destination of accesses to the BIOS memory range. The default values for these bits represent the strap values of GPIO51 (bit 11) at the rising edge of PWROK and SATA1GP/GPIO19 (bit 10) at the rising edge of PWROK. Bits 11:10 Description 00b LPC 01b Reserved 10b Reserved 11b SPI When SPI or LPC is selected, the range that is decoded is further qualified by other configuration bits described in the respective sections. The value in this field can be overwritten by software as long as the BIOS Interface Lock-Down (bit 0) is not set. Boot BIOS Destination Select to LPC by functional strap or using Boot BIOS Destination Bit will not affect SPI accesses initiated by Intel Management Engine or Integrated GbE LAN. 9 8:6 358 Server Error Reporting Mode (SERM)--R/W. 0 = The PCH is the final target of all errors. The processor sends a messages to the PCH for the purpose of generating NMI. 1 = The processor is the final target of all errors from PCI Express* and DMI. In this mode, if the PCH detects a fatal, non-fatal, or correctable error on DMI or its downstream ports, it sends a message to the processor. If the PCH receives an ERR_* message from the downstream port, it sends that message to the processor. Reserved 5 No Reboot (NR)--R/W. This bit is set when the "No Reboot" strap (SPKR pin on the PCH) is sampled high on PWROK. This bit may be set or cleared by software if the strap is sampled low but may not override the strap when it indicates "No Reboot". 0 = System will reboot upon the second timeout of the TCO timer. 1 = The TCO timer will count down and generate the SMI# on the first timeout, but will not reboot on the second timeout. 4 Alternate Access Mode Enable (AME)--R/W. 0 = Disabled. 1 = Alternate access read only registers can be written, and write only registers can be read. Before entering a low power state, several registers from powered down parts may need to be saved. In the majority of cases, this is not an issue, as registers have read and write paths. However, several of the ISA compatible registers are either read only or write only. To get data out of write-only registers, and to restore data into read-only registers, the PCH implements an alternate access mode. For a list of these registers see Section 5.14.9. 3 Shutdown Policy Select (SPS)--R/W. 0 = PCH will drive INIT# in response to the shutdown Vendor Defined Message (VDM). (default) 1 = PCH will treat the shutdown VDM similar to receiving a CF9h I/O write with data value 06h, and will drive PLTRST# active. 2 Reserved Page Route (RPR)--R/W. Determines where to send the reserved page registers. These addresses are sent to PCI or LPC for the purpose of generating POST codes. The I/O addresses modified by this field are: 80h, 84h, 85h, 86h, 88h, 8Ch, 8Dh, and 8Eh. 0 = Writes will be forwarded to LPC, shadowed within the PCH, and reads will be returned from the internal shadow 1 = Writes will be forwarded to PCI, shadowed within the PCH, and reads will be returned from the internal shadow. Note: if some writes are done to LPC/PCI to these I/O ranges, and then this bit is flipped, such that writes will now go to the other interface, the reads will not return what was last written. Shadowing is performed on each interface. The aliases for these registers, at 90h, 94h, 95h, 96h, 98h, 9Ch, 9Dh, and 9Eh, are always decoded to LPC. Datasheet Chipset Configuration Registers Bit 10.1.50 Description 1 Reserved 0 BIOS Interface Lock-Down (BILD)--R/WLO. 0 = Disabled. 1 = Prevents BUC.TS (offset 3414, bit 0) and GCS.BBS (offset 3410h, bits 11:10) from being changed. This bit can only be written from 0 to 1 once. BUC--Backed Up Control Register Offset Address: 3414h Default Value: 0000000xb Attribute: Size: R/W 8-bit All bits in this register are in the RTC well and only cleared by RTCRST#. Bit 7:6 Reserved 5 LAN Disable--R/W. 0 = LAN is Enabled 1 = LAN is Disabled. Changing the internal GbE controller from disabled to enabled requires a system reset (write of 0Eh to CF9h (RST_CNT Register)) immediately after clearing the LAN disable bit. A reset is not required if changing the bit from enabled to disabled. This bit is locked by the Function Disable SUS Well Lockdown register. Once locked, this bit cannot be changed by software. 4 Daylight Savings Override (SDO)--R/W. 0 = Daylight Savings is Enabled and configurable by software. 1 = The DSE bit in RTC Register B bit[0] is set to Read-only with a value of 0 to disable daylight savings. Note: System BIOS shall configure this bit accordingly during the boot process before RTC time is initialized. 3:1 0 10.1.51 Description Reserved Top Swap (TS)--R/W. 0 = PCH will not allow invert the boot block. 1 = PCH will allow boot block invert, for cycles going to the BIOS space. Note: If Top Swap is enabled (TS = 1b): 1. If booting from SPI, then the BIOS boot block size (BOOT_BLOCK_SIZE) soft strap determines if A16, A17, A18, A19 or A20 should be inverted. 2. If booting from LPC (FWH), then the boot-block size is hard-set to 64 KB and only A16 is inverted (soft strap is ignored in this case). 3. If PCH is strapped for Top Swap (GPIO55 is low at rising edge of PWROK), then this bit cannot be cleared by software. The strap jumper should be removed and the system rebooted. FD--Function Disable Register Offset Address: 3418-341Bh Default Value: See bit description Attribute: Size: R/W 32-bit When disabling a function, only the configuration space is disabled. Software must ensure that all functionality within a controller that is not desired (such as memory spaces, I/O spaces, and DMA engines) is disabled prior to disabling the function. When a function is disabled, software must not attempt to re-enable it. A disabled function can only be re-enabled by a platform reset. Datasheet 359 Chipset Configuration Registers Bit 31:28 27 Description Reserved XHCI Disable (XHD)--R/W. Default is 0. 0 = The XHCI controller is enabled. 1 = The XHCI controller is disabled. 26 Reserved 25 Serial ATA Disable 2 (SAD2)--R/W. Default is 0. 0 = The SATA controller #2 (D31:F5) is enabled. 1 = The SATA controller #2 (D31:F5) is disabled. 24 Thermal Sensor Registers Disable (TTD)--R/W. Default is 0. 0 = Thermal Sensor Registers (D31:F6) are enabled. 1 = Thermal Sensor Registers (D31:F6) are disabled. 23 PCI Express* 8 Disable (PE8D)--R/W. Default is 0. When disabled, the link for this port is put into the "link down" state. 0 = PCI Express* port #8 is enabled. 1 = PCI Express port #8 is disabled. 22 PCI Express 7 Disable (PE7D)--R/W. Default is 0. When disabled, the link for this port is put into the link down state. 0 = PCI Express port #7 is enabled. 1 = PCI Express port #7 is disabled. 21 PCI Express* 6 Disable (PE6D)--R/W. Default is 0. When disabled, the link for this port is put into the "link down" state. 0 = PCI Express* port #6 is enabled. 1 = PCI Express port #6 is disabled. 20 PCI Express 5 Disable (PE5D)--R/W. Default is 0. When disabled, the link for this port is put into the link down state. 0 = PCI Express port #5 is enabled. 1 = PCI Express port #5 is disabled. 19 PCI Express 4 Disable (PE4D)--R/W. Default is 0. When disabled, the link for this port is put into the "link down" state. 0 = PCI Express port #4 is enabled. 1 = PCI Express port #4 is disabled. Note: This bit must be set when Port 1 is configured as a x4. 18 PCI Express 3 Disable (PE3D)--R/W. Default is 0. When disabled, the link for this port is put into the link down state. 0 = PCI Express port #3 is enabled. 1 = PCI Express port #3 is disabled. Note: This bit must be set when Port 1 is configured as a x4. 17 PCI Express* 2 Disable (PE2D)--R/W. Default is 0. When disabled, the link for this port is put into the link down state. 0 = PCI Express port #2 is enabled. 1 = PCI Express port #2 is disabled. Note: This bit must be set when Port 1 is configured as a x4 or a x2. 16 PCI Express 1 Disable (PE1D)--R/W. Default is 0. When disabled, the link for this port is put into the link down state. 0 = PCI Express port #1 is enabled. 1 = PCI Express port #1 is disabled. 15 EHCI #1 Disable (EHCI1D)--R/W. Default is 0. 0 = The EHCI #1 is enabled. 1 = The EHCI #1 is disabled. 14 LPC Bridge Disable (LBD)--R/W. Default is 0. 0 = The LPC bridge is enabled. 1 = The LPC bridge is disabled. Unlike the other disables in this register, the following additional spaces will no longer be decoded by the LPC bridge: * Memory cycles below 16 MB (1000000h) * I/O cycles below 64 KB (10000h) * The Internal I/OxAPIC at FEC0_0000 to FECF_FFFF Memory cycle in the LPC BIOS range below 4 GB will still be decoded when this bit is set; however, the aliases at the top of 1 MB (the E and F segment) no longer will be decoded. 360 Datasheet Chipset Configuration Registers Bit 13 12:5 10.1.52 Description EHCI #2 Disable (EHCI2D)--R/W. Default is 0. 0 = The EHCI #2 is enabled. 1 = The EHCI #2 is disabled. Reserved 4 Intel(R) High Definition Audio Disable (HDAD)--R/W. Default is 0. 0 = The Intel High Definition Audio controller is enabled. 1 = The Intel High Definition Audio controller is disabled and its PCI configuration space is not accessible. 3 SMBus Disable (SD)--R/W. Default is 0. 0 = The SMBus controller is enabled. 1 = The SMBus controller is disabled. Setting this bit only disables the PCI configuration space. 2 Serial ATA Disable 1 (SAD1)--R/W. Default is 0. 0 = The SATA controller #1 (D31:F2) is enabled. 1 = The SATA controller #1 (D31:F2) is disabled. 1 Reserved. 0 BIOS must program this field to 1b. CG--Clock Gating Register Offset Address: 341C-341Fh Default Value: 00000000h Bit 31 30:24 R/W 32-bit Description Legacy (LPC) Dynamic Clock Gate Enable--R/W. 0 = Legacy Dynamic Clock Gating is Disabled 1 = Legacy Dynamic Clock Gating is Enabled Reserved 23 LAN Static Clock Gating Enable (LANSCGE)--R/W. 0 = LAN Static Clock Gating is Disabled 1 = LAN Static Clock Gating is Enabled when the LAN Disable bit is set in the Backed Up Control RTC register. 22 High Definition Audio Dynamic Clock Gate Enable--R/W. 0 = High Definition Audio Dynamic Clock Gating is Disabled 1 = High Definition Audio Dynamic Clock Gating is Enabled 21 High Definition Audio Static Clock Gate Enable--R/W. 0 = High Definition Audio Static Clock Gating is Disabled 1 = High Definition Audio Static Clock Gating is Enabled 20:17 16 15:6 5 4:0 Datasheet Attribute: Size: Reserved PCI Dynamic Gate Enable--R/W. 0 = PCI Dynamic Gating is Disabled 1 = PCI Dynamic Gating is Enabled Reserved SMBus Clock Gating Enable (SMBCGEN)--R/W. 0 = SMBus Clock Gating is Disabled. 1 = SMBus Clock Gating is Enabled. Note: Setting this bit will also clock gate all the TCO logic functionality. Reserved 361 Chipset Configuration Registers 10.1.53 FDSW--Function Disable SUS Well Register Offset Address: 3420h Default Value: 00h Bit 7 6:0 10.1.54 Attribute: Size: Description Function Disable SUS Well Lockdown (FDSWL)--R/W03 0 = FDSW registers are not locked down 1 = FDSW registers are locked down Note: This bit must be set when Intel(R) AMT is enabled. Reserved DISPBDF--Display Bus, Device and Function Initialization Register Offset Address: 3424-3427h Default Value: 00040010h Bit 10.1.55 R/W 8-bit Attribute: Size: R/W 32-bit Description 31:19 Reserved. 18:16 Display Target Block (DTB)--R/W. The Target BLK field that the PCH South Display controller should use when sending RAVDM messages to the processor. BIOS must program this field to 110h. 15:8 Display Bus Number (DBN)--R/W. The bus number of the Display in the processor. BIOS must program this field to 0h. 7:3 Display Device Number (DDN)--R/W. The device number of the Display in the processor. BIOS must program this field to 2h. 2:0 Display Function Number (DFN)--R/W. The function number of the Display in the processor. BIOS must program this field to 0h. FD2--Function Disable 2 Register Offset Address: 3428-342Bh Default Value: 00000000h Bit 31:5 Attribute: Size: R/W 32-bit Description Reserved 4 KT Disable (KTD)--R/W. Default is 0. 0 = Keyboard Text controller (D22:F3) is enabled. 1 = Keyboard Text controller (D22:F3) is Disabled 3 IDE-R Disable (IRERD)--R/W. Default is 0. 0 = IDE Redirect controller (D22:F2) is Enabled. 1 = IDE Redirect controller (D22:F2) is Disabled. 2 Intel(R) MEI #2 Disable (MEI2D)--R/W. Default is 0. 0 = Intel MEI controller #2 (D22:F1) is enabled. 1 = Intel MEI controller #2 (D22:F1) is disabled. 1 Intel MEI #1 Disable (MEI1D)--R/W. Default is 0. 0 = Intel MEI controller #1 (D22:F0) is enabled. 1 = Intel MEI controller #1 (D22:F0) is disabled. 0 Display BDF Enable (DBDFEN)--R/W. Default is 0. 362 Datasheet Gigabit LAN Configuration Registers 11 Gigabit LAN Configuration Registers 11.1 Gigabit LAN Configuration Registers (Gigabit LAN--D25:F0) Note: Register address locations that are not shown in Table 11-1 should be treated as Reserved. All GbE registers are located in the VccASW power well. Table 11-1. Gigabit LAN Configuration Registers Address Map (Gigabit LAN--D25:F0) (Sheet 1 of 2) / Offset Datasheet Mnemonic Register Name Default Attribute 00h-01h VID Vendor Identification 8086h RO 02h-03h DID Device Identification See register description RO 04h-05h PCICMD PCI Command 0000h R/W, RO 06h-07h PCISTS PCI Status 0010h R/WC, RO 08h RID Revision Identification See register description RO 09h-0Bh CC Class Code 020000h RO 0Ch CLS Cache Line Size 00h R/W 0Dh PLT Primary Latency Timer 00h RO 0Eh HEADTYP 10h-13h MBARA Header Type Memory Base Address A 00h RO 00000000h R/W, RO 14h-17h MBARB Memory Base Address B 00000000h R/W, RO 18h-1Bh MBARC Memory Base Address C 00000001h R/W, RO 2Ch-2Dh SVID Subsystem Vendor ID See register description RO 2Eh-2Fh SID Subsystem ID See register description RO 30h-33h ERBA Expansion ROM Base Address See register description RO 34h CAPP Capabilities List Pointer C8h RO 3Ch-3Dh INTR Interrupt Information See register description R/W, RO 3Eh-3Fh MLMG Maximum Latency / Minimum Grant 0000h RO A0h-A3h STCL System Time Capture Low 00000000h RO A4h-A7h STCH System Time Capture High 00000000h RO Latency Tolerance Reporting 00000000h R/W D001h RO PCI Power Management Capability See register description RO PCI Power Management Control and Status See register description R/WC, R/W, RO A8h-ABh LTR C8h-C9h CLIST1 CAh-CBh PMC CCh-CDh PMCS Capabilities List 1 363 Gigabit LAN Configuration Registers Table 11-1. Gigabit LAN Configuration Registers Address Map (Gigabit LAN--D25:F0) (Sheet 2 of 2) 11.1.1 Offset Mnemonic Register Name Default Attribute CFh DR See register description RO D0h-D1h CLIST2 D2h-D3h MCTL Capabilities List 2 E005h R/WO, RO Message Control 0080h R/W, RO D4h-D7h MADDL Message Address Low See register description R/W D8h-dBh MADDH Message Address High See register description R/W DCh-DDh MDAT Message Data See register description R/W E0h-E1h FLRCAP Function Level Reset Capability 0009h RO E2h-E3h FLRCLV Function Level Reset Capability Length and Value See register description R/WO, RO E4h-E5h DEVCTRL 0000h R/W, RO Data Register Device Control VID--Vendor Identification Register (Gigabit LAN--D25:F0) Address Offset: 00h-01h Default Value: 8086h Bit 15:0 11.1.2 Attribute: Size: Description Vendor ID--RO. This is a 16-bit value assigned to Intel. The field may be auto-loaded from the NVM at address 0Dh during init time depending on the "Load Vendor/Device ID" bit field in NVM word 0Ah with a default value of 8086h. DID--Device Identification Register (Gigabit LAN--D25:F0) Address Offset: 02h-03h Default Value: See bit description 364 RO 16 bits Attribute: Size: RO 16 bits Bit Description 15:0 Device ID--RO. This is a 16-bit value assigned to the PCH Gigabit LAN controller. The field may be auto-loaded from the NVM word 0Dh during initialization time depending on the "Load Vendor/ Device ID" bit field in NVM word 0Ah. Datasheet Gigabit LAN Configuration Registers 11.1.3 PCICMD--PCI Command Register (Gigabit LAN--D25:F0) Address Offset: 04h-05h Default Value: 0000h Bit 15:11 10 11.1.4 Attribute: Size: Description Reserved Interrupt Disable--R/W. This disables pin-based INTx# interrupts on enabled Hot-Plug and power management events. This bit has no effect on MSI operation. 0 = Internal INTx# messages are generated if there is an interrupt for Hot-Plug or power management and MSI is not enabled. 1 = Internal INTx# messages will not be generated. This bit does not affect interrupt forwarding from devices connected to the root port. Assert_INTx and Deassert_INTx messages will still be forwarded to the internal interrupt controllers if this bit is set. 9 Fast Back to Back Enable (FBE)--RO. Hardwired to 0. 8 SERR# Enable (SEE)--R/W. 0 = Disable 1 = Enables the Gb LAN controller to generate an SERR# message when PSTS.SSE is set. 7 Wait Cycle Control (WCC)--RO. Hardwired to 0. 6 Parity Error Response (PER)--R/W. 0 = Disable. 1 = Indicates that the device is capable of reporting parity errors as a master on the backbone. 5 Palette Snoop Enable (PSE)--RO. Hardwired to 0. 4 Postable Memory Write Enable (PMWE)--RO. Hardwired to 0. 3 Special Cycle Enable (SCE)--RO. Hardwired to 0. 2 Bus Master Enable (BME)--R/W. 0 = Disable. All cycles from the device are master aborted 1 = Enable. Allows the root port to forward cycles onto the backbone from a Gigabit LAN* device. 1 Memory Space Enable (MSE)--R/W. 0 = Disable. Memory cycles within the range specified by the memory base and limit registers are master aborted on the backbone. 1 = Enable. Allows memory cycles within the range specified by the memory base and limit registers can be forwarded to the Gigabit LAN device. 0 I/O Space Enable (IOSE)--R/W. This bit controls access to the I/O space registers. 0 = Disable. I/O cycles within the range specified by the I/O base and limit registers are master aborted on the backbone. 1 = Enable. Allows I/O cycles within the range specified by the I/O base and limit registers can be forwarded to the Gigabit LAN device. PCISTS--PCI Status Register (Gigabit LAN--D25:F0) Address Offset: 06h-07h Default Value: 0010h Bit Datasheet R/W, RO 16 bits Attribute: Size: R/WC, RO 16 bits Description 15 Detected Parity Error (DPE)--R/WC. 0 = No parity error detected. 1 = Set when the Gb LAN controller receives a command or data from the backbone with a parity error. This is set even if PCIMD.PER (D25:F0, bit 6) is not set. 14 Signaled System Error (SSE)--R/WC. 0 = No system error signaled. 1 = Set when the Gb LAN controller signals a system error to the internal SERR# logic. 365 Gigabit LAN Configuration Registers Bit 13 Received Master Abort (RMA)--R/WC. 0 = Root port has not received a completion with unsupported request status from the backbone. 1 = Set when the GbE LAN controller receives a completion with unsupported request status from the backbone. 12 Received Target Abort (RTA)--R/WC. 0 = Root port has not received a completion with completer abort from the backbone. 1 = Set when the Gb LAN controller receives a completion with completer abort from the backbone. 11 Signaled Target Abort (STA)--R/WC. 0 = No target abort received. 1 = Set whenever the Gb LAN controller forwards a target abort received from the downstream device onto the backbone. 10:9 DEVSEL# Timing Status (DEV_STS)--RO. Hardwired to 0. 8 Master Data Parity Error Detected (DPED)--R/WC. 0 = No data parity error received. 1 = Set when the Gb LAN Controller receives a completion with a data parity error on the backbone and PCIMD.PER (D25:F0, bit 6) is set. 7 Fast Back to Back Capable (FB2BC)--RO. Hardwired to 0. 6 Reserved 5 66 MHz Capable--RO. Hardwired to 0. 4 Capabilities List--RO. Hardwired to 1. Indicates the presence of a capabilities list. 3 Interrupt Status--RO. Indicates status of Hot-Plug and power management interrupts on the 2:0 11.1.5 Description root port that result in INTx# message generation. 0 = Interrupt is de-asserted. 1 = Interrupt is asserted. This bit is not set if MSI is enabled. If MSI is not enabled, this bit is set regardless of the state of PCICMD.Interrupt Disable bit (D25:F0:04h:bit 10). Reserved RID--Revision Identification Register (Gigabit LAN--D25:F0) Offset Address: 08h Default Value: See bit description 11.1.6 Attribute: Size: Bit Description 7:0 Revision ID--RO. This field indicates the device specific revision identifier. See Section 1.3 for the value of the RID Register. CC--Class Code Register (Gigabit LAN--D25:F0) Address Offset: 09h-0Bh Default Value: 020000h Bit 23:0 366 RO 8 bits Attribute: Size: RO 24 bits Description Class Code--RO. Identifies the device as an Ethernet Adapter. 020000h = Ethernet Adapter. Datasheet Gigabit LAN Configuration Registers 11.1.7 CLS--Cache Line Size Register (Gigabit LAN--D25:F0) Address Offset: 0Ch Default Value: 00h Bit 7:0 11.1.8 Attribute: Size: Description Cache Line Size--R/W. This field is implemented by PCI devices as a read write field for legacy compatibility purposes but has no impact on any device functionality. PLT--Primary Latency Timer Register (Gigabit LAN--D25:F0) Address Offset: 0Dh Default Value: 00h Bit 7:0 11.1.9 Attribute: Size: RO 8 bits Attribute: Size: RO 8 bits Description Latency Timer (LT)--RO. Hardwired to 0. HEADTYP--Header Type Register (Gigabit LAN--D25:F0) Address Offset: 0Eh Default Value: 00h Bit 7:0 11.1.10 R/W 8 bits Description Header Type (HT)--RO. 00h = Indicates this is a single function device. MBARA--Memory Base Address Register A (Gigabit LAN--D25:F0) Address Offset: 10h-13h Default Value: 00000000h Attribute: Size: R/W, RO 32 bits The internal CSR registers and memories are accessed as direct memory mapped offsets from the base address register. SW may only access whole DWord at a time. Bit 31:17 16:4 3 2:1 0 Datasheet Description Base Address (BA)--R/W. Software programs this field with the base address of this region. Memory Size (MSIZE)--RO. Memory size is 128 KB. Prefetchable Memory (PM)--RO. The GbE LAN controller does not implement prefetchable memory. Memory Type (MT)--RO. Set to 00b indicating a 32-bit BAR. Memory / IO Space (MIOS)--RO. Set to 0 indicating a Memory Space BAR. 367 Gigabit LAN Configuration Registers 11.1.11 MBARB--Memory Base Address Register B (Gigabit LAN--D25:F0) Address Offset: 14h-17h Default Value: 00000000h Attribute: Size: R/W, RO 32 bits The internal registers that are used to access the LAN Space in the External FLASH device. Access to these registers are direct memory mapped offsets from the base address register. Software may only access a DWord at a time. Bit 31:12 11:4 3 2:1 0 11.1.12 Description Base Address (BA)--R/W. Software programs this field with the base address of this region. Memory Size (MSIZE)--RO. Memory size is 4 KB. Prefetchable Memory (PM)--RO. Set to 0b indicating the Gb LAN controller does not implement prefetchable memory. Memory Type (MT)--RO. Set to 00b indicating a 32-bit BAR. Memory / I/O Space (MIOS)--RO. Set to 0 indicating a Memory Space BAR. MBARC--Memory Base Address Register C (Gigabit LAN--D25:F0) Address Offset: 18h-1Bh Default Value: 00000001h Attribute: Size: R/W, RO 32 bits Internal registers, and memories, can be accessed using I/O operations. There are two 4 Byte registers in the I/O mapping window: Addr Reg and Data Reg. Software may only access a DWord at a time. Bit 31:5 4:1 0 11.1.13 Description Base Address (BA)--R/W. Software programs this field with the base address of this region. I/O Size (IOSIZE)--RO. I/O space size is 32 Bytes. Memory / I/O Space (MIOS)--RO. Set to 1 indicating an I/O Space BAR. SVID--Subsystem Vendor ID Register (Gigabit LAN--D25:F0) Address Offset: 2Ch-2Dh Default Value: See bit description 368 Attribute: Size: RO 16 bits Bit Description 15:0 Subsystem Vendor ID (SVID)--RO. This value may be loaded automatically from the NVM Word 0Ch upon power up or reset depending on the "Load Subsystem ID" bit field in NVM word 0Ah. A value of 8086h is default for this field upon power up if the NVM does not respond or is not programmed. All functions are initialized to the same value. Datasheet Gigabit LAN Configuration Registers 11.1.14 SID--Subsystem ID Register (Gigabit LAN--D25:F0) Address Offset: 2Eh-2Fh Default Value: See bit description 11.1.15 Attribute: Size: Bit Description 15:0 Subsystem ID (SID)--RO. This value may be loaded automatically from the NVM Word 0Bh upon power up or reset depending on the "Load Subsystem ID" bit field in NVM word 0Ah with a default value of 0000h. This value is loadable from NVM word location 0Ah. ERBA--Expansion ROM Base Address Register (Gigabit LAN--D25:F0) Address Offset: 30h-33h Default Value: See bit description 11.1.16 Attribute: Size: Description 31:0 Expansion ROM Base Address (ERBA)--RO. This register is used to define the address and size information for boot-time access to the optional FLASH memory. If no Flash memory exists, this register reports 00000000h. CAPP--Capabilities List Pointer Register (Gigabit LAN--D25:F0) Attribute: Size: Description 7:0 Capabilities Pointer (PTR)--RO. Indicates that the pointer for the first entry in the capabilities list is at C8h in configuration space. INTR--Interrupt Information Register (Gigabit LAN--D25:F0) Bit 15:8 7:0 Attribute: Size: R/W, RO 16 bits Description Interrupt Pin (IPIN)--RO. Indicates the interrupt pin driven by the GbE LAN controller. 01h = The GbE LAN controller implements legacy interrupts on INTA. Interrupt Line (ILINE)--R/W. Default = 00h. Software written value to indicate which interrupt line (vector) the interrupt is connected to. No hardware action is taken on this register. MLMG--Maximum Latency / Minimum Grant Register (Gigabit LAN--D25:F0) Address Offset: 3Eh-3Fh Default Value: 0000h Bit 7:0 Datasheet RO 8 bits Bit Address Offset: 3Ch-3Dh Default Value: 0100h Function Level Reset: No 11.1.18 RO 32 bits Bit Address Offset: 34h Default Value: C8h 11.1.17 RO 16 bits Attribute: Size: RO 16 bits Description Maximum Latency/Minimum Grant (MLMG)--RO. Not used. Hardwired to 00h. 369 Gigabit LAN Configuration Registers 11.1.19 STCL--System Time Control Low Register (Gigabit LAN--D25:F0) Address Offset: A0h-A3h Default Value: 00000000h 11.1.20 Attribute: Size: Bit Description 31:0 System Time Control Low (STCL)--RO. Lower 32 bits of the system time capture used for audio stream synchronization. STCH--System Time Control High Register (Gigabit LAN--D25:F0) Address Offset: A4h-A7h Default Value: 00000000h 11.1.21 Attribute: Size: RO 32 bits Bit Description 31:0 System Time Control High (STCH)--RO. Upper 32 bits of the system time capture used for audio stream synchronization. LTRCAP--System Time Control High Register (Gigabit LAN--D25:F0) Address Offset: A8h-ABh Default Value: 00000000h Bit Attribute: Size: R/W 32 bits Description 31:29 Reserved 28:26 Maximum Non-Snoop Latency Scale (MNSLS)--R/W. Provides a scale for the value contained within the Maximum Non-Snoop Latency Value field. 000b = Value times 1 ns 001b = Value times 32 ns 010b = Value times 1,024 ns 011b = Value times 32,768 ns 100b = Value times 1,048,576 ns 101b = Value times 33,554,432 ns 110b-111b = Reserved 25:16 Maximum Non-Snoop Latency (MNSL)--R/W. Specifies the maximum non-snoop latency that a device is permitted to request. Software should set this to the platform's maximum supported latency or less. This field is also an indicator of the platforms maximum latency, should an endpoint send up LTR Latency Values with the Requirement bit not set. 15:13 Reserved 12:10 Maximum Snoop Latency Scale (MSLS)--R/W. Provides a scale for the value contained within the Maximum Snoop Latency Value field. 000b = Value times 1 ns 001b = Value times 32 ns 010b = Value times 1,024 ns 011b = Value times 32,768 ns 100b = Value times 1,048,576 ns 101b = Value times 33,554,432 ns 110b-111b = Reserved 9:0 370 RO 32 bits Maximum Snoop Latency (MSL)--R/W. Specifies the maximum snoop latency that a device is permitted to request. Software should set this to the platform's maximum supported latency or less. This field is also an indicator of the platforms maximum latency, should an endpoint send up LTR Latency Values with the Requirement bit not set. Datasheet Gigabit LAN Configuration Registers 11.1.22 CLIST1--Capabilities List Register 1 (Gigabit LAN--D25:F0) Address Offset: C8h-C9h Default Value: D001h Attribute: Size: Bit 15:8 7:0 11.1.23 RO 16 bits Description Next Capability (NEXT)--RO. Value of D0h indicates the location of the next pointer. Capability ID (CID)--RO. Indicates the linked list item is a PCI Power Management Register. PMC--PCI Power Management Capabilities Register (Gigabit LAN--D25:F0) Address Offset: CAh-CBh Default Value: See bit descriptions Function Level Reset:No (Bits 15:11 only) Attribute: Size: RO 16 bits Bit Description 15:11 PME_Support (PMES)--RO. This five-bit field indicates the power states in which the function may assert PME#. It depend on PM Ena and AUX-PWR bits in word 0Ah in the NVM: Condition Functionality Value PM Ena=0 No PME at all states 0000b PM Ena & AUX-PWR=0 PME at D0 and D3hot 01001b PM Ena & AUX-PWR=1 PME at D0, D3hot and D3cold 11001b These bits are not reset by Function Level Reset. 10 D2_Support (D2S)--RO. The D2 state is not supported. 9 D1_Support (D1S)--RO. The D1 state is not supported. 8:6 Device Specific Initialization (DSI)--RO. Set to 1. The GbE LAN Controller requires its device driver to be executed following transition to the D0 un-initialized state. 4 Reserved 3 PME Clock (PMEC)--RO. Hardwired to 0. 2:0 11.1.24 Aux_Current (AC)--RO. Required current defined in the Data Register. 5 Version (VS)--RO. Hardwired to 010b to indicate support for Revision 1.1 of the PCI Power Management Specification. PMCS--PCI Power Management Control and Status Register (Gigabit LAN--D25:F0) Address Offset: CCh-CDh Default Value: See bit description Function Level Reset:No (Bit 8 only) Bit 15 14:13 Datasheet Attribute: Size: R/WC, R/W, RO 16 bits Description PME Status (PMES)--R/WC. This bit is set to 1 when the function detects a wake-up event independent of the state of the PMEE bit. Writing a 1 will clear this bit. Data Scale (DSC)--RO. This field indicates the scaling factor to be used when interpreting the value of the Data register. For the GbE LAN and common functions this field equals 01b (indicating 0.1 watt units) if the PM is enabled in the NVM, and the Data_Select field is set to 0, 3, 4, 7, (or 8 for Function 0). Else it equals 00b. For the manageability functions this field equals 10b (indicating 0.01 watt units) if the PM is enabled in the NVM, and the Data_Select field is set to 0, 3, 4, 7. Else it equals 00b. 371 Gigabit LAN Configuration Registers Bit 12:9 Data Select (DSL)--R/W. This four-bit field is used to select which data is to be reported through the Data register (offset CFh) and Data_Scale field. These bits are writeable only when the Power Management is enabled using NVM. 0h = D0 Power Consumption 3h = D3 Power Consumption 4h = D0 Power Dissipation 7h = D3 Power Dissipation 8h = Common Power All other values are reserved. 8 PME Enable (PMEE)--R/W. If Power Management is enabled in the NVM, writing a 1 to this register will enable Wakeup. If Power Management is disabled in the NVM, writing a 1 to this bit has no affect, and will not set the bit to 1. This bit is not reset by Function Level Reset. 7:4 3 2 1:0 11.1.25 Description Reserved - Returns a value of 0000. No Soft Reset (NSR)--RO. Defines if the device executed internal reset on the transition to D0. the LAN controller always reports 0 in this field. Reserved - Returns a value of 0b. Power State (PS)--R/W. This field is used both to determine the current power state of the GbE LAN Controller and to set a new power state. The values are: 00 = D0 state (default) 01 = Ignored 10 = Ignored 11 = D3 state (Power Management must be enabled in the NVM or this cycle will be ignored). DR--Data Register (Gigabit LAN--D25:F0) Address Offset: CFh Default Value: See bit description 11.1.26 Attribute: Size: Bit Description 7:0 Reported Data (RD)--RO. This register is used to report power consumption and heat dissipation. This register is controlled by the Data_Select field in the PMCS (Offset CCh, bits 12:9), and the power scale is reported in the Data_Scale field in the PMCS (Offset CCh, bits 14:13). The data of this field is loaded from the NVM if PM is enabled in the NVM or with a default value of 00h otherwise. CLIST2--Capabilities List Register 2 (Gigabit LAN--D25:F0) Address Offset: D0h-D1h Default Value: E005h Function Level Reset: No (Bits 15:8 only) Bit 15:8 7:0 372 RO 8 bits Attribute: Size: R/WO, RO 16 bits Description Next Capability (NEXT)--R/WO. Value of E0h points to the Function Level Reset capability structure. These bits are not reset by Function Level Reset. Capability ID (CID)--RO. Indicates the linked list item is a Message Signaled Interrupt Register. Datasheet Gigabit LAN Configuration Registers 11.1.27 MCTL--Message Control Register (Gigabit LAN--D25:F0) Address Offset: D2h-D3h Default Value: 0080h Bit 15:8 7 11.1.28 Attribute: Size: Description Reserved 64-bit Capable (CID)--RO. Set to 1 to indicate that the GbE LAN Controller is capable of generating 64-bit message addresses. 6:4 Multiple Message Enable (MME)--RO. Returns 000b to indicate that the GbE LAN controller only supports a single message. 3:1 Multiple Message Capable (MMC)--RO. The GbE LAN controller does not support multiple messages. 0 MSI Enable (MSIE)--R/W. 0 = MSI generation is disabled. 1 = The Gb LAN controller will generate MSI for interrupt assertion instead of INTx signaling. MADDL--Message Address Low Register (Gigabit LAN--D25:F0) Address Offset: D4h-D7h Default Value: See bit description 11.1.29 Attribute: Size: Description 31:0 Message Address Low (MADDL)--R/W. Written by the system to indicate the lower 32 bits of the address to use for the MSI memory write transaction. The lower two bits will always return 0 regardless of the write operation. MADDH--Message Address High Register (Gigabit LAN--D25:F0) Bit 31:0 Attribute: Size: R/W 32 bits Description Message Address High (MADDH)--R/W. Written by the system to indicate the upper 32 bits of the address to use for the MSI memory write transaction. MDAT--Message Data Register (Gigabit LAN--D25:F0) Address Offset: DCh-DDh Default Value: See bit description Datasheet R/W 32 bits Bit Address Offset: D8h-dBh Default Value: See bit description 11.1.30 R/W, RO 16 bits Attribute: Size: R/W 16 bits Bit Description 31:0 Message Data (MDAT)--R/W. Written by the system to indicate the lower 16 bits of the data written in the MSI memory write DWord transaction. The upper 16 bits of the transaction are written as 0000h. 373 Gigabit LAN Configuration Registers 11.1.31 FLRCAP--Function Level Reset Capability (Gigabit LAN--D25:F0) Address Offset: E0h-E1h Default Value: 0009h RO 16 bits Bit Description 15:8 Next Pointer--RO. This field provides an offset to the next capability item in the capability list. The value of 00h indicates the last item in the list. 7:0 11.1.32 Attribute: Size: Capability ID--RO. The value of this field depends on the FLRCSSEL bit. 13h = If FLRCSSEL = 0 09h = If FLRCSSEL = 1, indicating vendor specific capability. FLRCSSEL is located at RCBA + 3410(bit 12). See Chapter 10, "Chipset Configuration Registers". FLRCLV--Function Level Reset Capability Length and Version Register (Gigabit LAN--D25:F0) Address Offset: E2h-E3h Attribute: Default Value: See Description. Size: Function Level Reset: No (Bits 9:8 Only When FLRCSSEL = 0) R/WO, RO 16 bits When FLRCSSEL = 0, this register is defined as follows: Bit 15:10 Description Reserved 9 Function Level Reset Capability--R/WO. 1 = Support for Function Level Reset. This bit is not reset by Function Level Reset. 8 TXP Capability--R/WO. 1 = Indicates support for the Transactions Pending (TXP) bit. TXP must be supported if FLR is supported. 7:0 Capability Length--RO. The value of this field indicates the number of bytes of the vendor specific capability as require by the PCI specification. It has the value of 06h for the Function Level Reset capability. When FLRCSSEL = 1, this register is defined as follows: Bit Description 15:12 Vendor Specific Capability ID--RO. A value of 2h in this field identifies this capability as Function Level Reset. 11:8 7:0 374 Capability Version--RO. The value of this field indicates the version of the Function Level Reset Capability. Default is 0h. Capability Length--RO. The value of this field indicates the number of bytes of the vendor specific capability as require by the PCI specification. It has the value of 06h for the Function Level Reset capability. Datasheet Gigabit LAN Configuration Registers 11.1.33 DEVCTRL--Device Control Register (Gigabit LAN--D25:F0) Address Offset: E4-E5h Default Value: 0000h Bit 15:9 8 7:1 0 11.2 Attribute: Size: R/W 16 bits Description Reserved Transactions Pending (TXP)--R/W. 1 = Indicates the controller has issued Non-Posted requests which have not been completed. 0 = Indicates that completions for all Non-Posted requests have been received. Reserved Initiate Function Level Reset--R/W. This bit is used to initiate an FLT transition. A write of 1 initiates the transition. Since hardware must not respond to any cycles until Function Level Reset completion, the value read by software from this bit is 0. Gigabit LAN Capabilities and Status Registers (CSR) The internal CSR registers and memories are accessed as direct memory mapped offsets from the base address register in Section 11.1.10. Software may only access whole DWord at a time. Note: Register address locations that are not shown in Table 11-1 should be treated as Reserved. Table 11-2. Gigabit LAN Capabilities and Status Registers Address Map (Gigabit LAN--MBARA) Datasheet MBARA + Offset Mnemonic 00h-03h GBECSR_00 18h-1Bh Register Name Default Attribute Gigabit Ethernet Capabilities and Status Register 00 00100241h R/W GBECSR_18 Gigabit Ethernet Capabilities and Status Register 18 01501000h R/W/SN 20h-23h GBECSR_20 Gigabit Ethernet Capabilities and Status Register 20 1000XXXXh R/W/V F00h-F03h GBECSR_F00 Gigabit Ethernet Capabilities and Status Register F00 00010008h R/W/V F10h-F13h GBECSR_F10 Gigabit Ethernet Capabilities and Status Register F10 0004000Ch R/W/SN 5400h-5403h GBECSR_5400 Gigabit Ethernet Capabilities and Status Register 5400 XXXXXXXXh R/W 5404h-5407h GBECSR_5404 Gigabit Ethernet Capabilities and Status Register 5404 XXXXXXXXh R/W 5800h-5803h GBECSR_5800 Gigabit Ethernet Capabilities and Status Register 5800 00000008h R/W/SN 5B54h-5B57h GBECSR_5B54 Gigabit Ethernet Capabilities and Status Register 5B54 60000040h RO 375 Gigabit LAN Configuration Registers 11.2.1 GBECSR_00--Gigabit Ethernet Capabilities and Status Register 00 Address Offset: MBARA + 00h Default Value: 00100241h Bit 31:25 24 23:0 11.2.2 Attribute: Size: Description Reserved PHY Power Down (PHYPDN)--R/W. When cleared (0b), the PHY power down setting is controlled by the internal logic of PCH. Reserved GBECSR_18--Gigabit Ethernet Capabilities and Status Register 18 Address Offset: MBARA + 18h Default Value: 01501000h Bit 31:21 20 19:0 11.2.3 Attribute: Size: R/W/SN 32 bit Description Reserved PHY Power Down Enable (PHYPDEN)--R/W/SN. When set, this bit enables the PHY to enter a low-power state when the LAN controller is at the DMoff/D3 or with no WOL. Reserved GBECSR_20--Gigabit Ethernet Capabilities and Status Register 20 Address Offset: MBARA + 20h Default Value: 1000XXXXh Attribute: Size: R/W/V 32 bit Bit Description 31 WAIT--RO. Set to 1 by the Gigabit Ethernet Controller to indicate that a PCI Express* to SMBus transition is taking place. The ME/Host should not issue new MDIC transactions while this bit is set to 1. This bit is auto cleared by HW after the transition has occurred. 30 Error--R/W/V. Set to 1 by the Gigabit Ethernet Controller when it fails to complete an MDI read. Software should make sure this bit is clear before making an MDI read or write command. 29 Reserved 28 Ready Bit (RB)--R/W/V. Set to 1 by the Gigabit Ethernet Controller at the end of the MDI transaction. This bit should be reset to 0 by software at the same time the command is written. 27:26 MDI Type--R/W/V. 01 = MDI Write 10 = MDI Read All other values are reserved. 25:21 LAN Connected Device Address (PHYADD)--R/W/V. 20:16 LAN Connected Device Register Address (PHYREGADD)--R/W/V. 15:0 376 R/W 32 bit DATA--R/W/V. Datasheet Gigabit LAN Configuration Registers 11.2.4 GBECSR_F00--Gigabit Ethernet Capabilities and Status Register F00 Address Offset: MBARA + F00h Default Value: 00010008h Bit 31:6 5 4:0 11.2.5 Attribute: Size: Description Reserved SW Semaphore FLAG (SWFLAG)--R/W/V. This bit is set by the device driver to gain access permission to shared CSR registers with the firmware and hardware. Reserved GBECSR_F10--Gigabit Ethernet Capabilities and Status Register F10 Address Offset: MBARA + F10h Default Value: 0004000Ch Bit 31:7 6 5:4 11.2.6 Attribute: Size: Reserved Global GbE Disable (GGD)--R/W/SN. Prevents the PHY from auto-negotiating 1000Mb/s link in all power states. Reserved 3 GbE Disable at non D0a--R/W/SN. Prevents the PHY from auto-negotiating 1000Mb/s link in all power states except D0a. This bit must be set since GbE is not supported in Sx states. 2 LPLU in non D0a (LPLUND)--R/W/SN. Enables the PHY to negotiate for the slowest possible link in all power states except D0a. 1 LPLU in D0a (LPLUD)--R/W/SN. Enables the PHY to negotiate for the slowest possible link in all power states. This bit overrides bit 2. 0 Reserved GBECSR_5400--Gigabit Ethernet Capabilities and Status Register 5400 Bit 31:0 Attribute: Size: R/W 32 bits Description Receive Address Low (RAL)--R/W. The lower 32 bits of the 48 bit Ethernet Address. GBECSR_5404--Gigabit Ethernet Capabilities and Status Register 5404 Address Offset: MBARA + 5404h Default Value: XXXXXXXXh Bit 31 30:16 Datasheet R/W/SN 32 bits Description Address Offset: MBARA + 5400h Default Value: XXXXXXXXh 11.2.7 R/W/V 32 bits Attribute: Size: R/W 32 bits Description Address Valid--R/W. Reserved 377 Gigabit LAN Configuration Registers Bit 15:0 11.2.8 Description Receive Address High (RAH)--R/W. The lower 16 bits of the 48 bit Ethernet Address. GBECSR_5800--Gigabit Ethernet Capabilities and Status Register 5800 Address Offset: MBARA + 5800h Default Value: 00000008h Bit 31:1 0 11.2.9 Attribute: Size: R/W/SN 32 bits Description Reserved Advanced Power Management Enable (APME)--R/W/SN. 1 = APM Wakeup is enabled 0 = APM Wakeup is disabled GBECSR_5B54--Gigabit Ethernet Capabilities and Status Register 5B54 Address Offset: MBARA + 5B54h Default Value: 60000040h Bit 31:16 15 14:0 Attribute: Size: RO 32 bits Description Reserved Firmware Valid Bit (FWVAL)--RO. 1 = Firmware is ready 0 = Firmware is not ready Reserved 378 Datasheet LPC Interface Bridge Registers (D31:F0) 12 LPC Interface Bridge Registers (D31:F0) The LPC bridge function of the PCH resides in PCI D31:F0. This function contains many other functional units, such as DMA and Interrupt controllers, Timers, Power Management, System Management, GPIO, RTC, and LPC Configuration Registers. Registers and functions associated with other functional units are described in their respective sections. 12.1 PCI Configuration Registers (LPC I/F--D31:F0) Note: Address locations that are not shown should be treated as Reserved. Table 12-1. LPC Interface PCI Register Address Map (LPC I/F--D31:F0) (Sheet 1 of 2) Datasheet Offset Mnemonic 00h-01h VID 02h-03h DID 04h-05h PCICMD 06h-07h PCISTS 08h RID 09h PI 0Ah SCC Register Name Default Attribute Vendor Identification 8086h RO Device Identification See register description RO 0007h R/W, RO PCI Command 0210h R/WC, RO Revision Identification PCI Status See register description R/WO Programming Interface 00h RO Sub Class Code 01h RO 0Bh BCC Base Class Code 06h RO 0Dh PLT Primary Latency Timer 00h RO 0Eh HEADTYP 2Ch-2Fh SS 40h-43h PMBASE 44h ACPI_CNTL 48h-4Bh GPIOBASE 4Ch GC 60h-63h PIRQ[n]_ROUT 64h SIRQ_CNTL 68h-6Bh PIRQ[n]_ROUT 6Ch-6Dh LPC_IBDF Header Type 80h RO Sub System Identifiers 00000000h R/WO ACPI Base Address 00000001h R/W, RO 00h R/W 00000001h R/W, RO 00h R/W ACPI Control GPIO Base Address GPIO Control PIRQ[A,B,C,D] Routing Control 80808080h R/W 10h R/W, RO PIRQ[E,F,G,H] Routing Control 80808080h R/W IOxAPIC Bus:Device:Function 00F8h R/W Serial IRQ Control 70h-7Fh LPC_HnBDF HPET Configuration 00F8h R/W 80h LPC_I/O_DEC I/O Decode Ranges 0000h R/W 82h-83h LPC_EN 84h-87h GEN1_DEC LPC I/F Enables LPC I/F Generic Decode Range 1 0000h R/W 00000000h R/W 88h-8Bh GEN2_DEC LPC I/F Generic Decode Range 2 00000000h R/W 8Ch-8Eh GEN3_DEC LPC I/F Generic Decode Range 3 00000000h R/W 379 LPC Interface Bridge Registers (D31:F0) Table 12-1. LPC Interface PCI Register Address Map (LPC I/F--D31:F0) (Sheet 2 of 2) Offset Mnemonic 90h-93h GEN4_DEC 94h-97h ULKMC 98h-9Bh LGMR A0h-CFh 12.1.1 Register Name 00000000h R/W USB Legacy Keyboard / Mouse Control 00002000h RO, R/WC, R/ W LPC I/F Generic Memory Range 00000000h R/W Power Management (See Section 12.8.1) D0h-D3h BIOS_SEL1 BIOS Select 1 00112233h R/W, RO D4h-D5h BIOS_SEL2 BIOS Select 2 4567h R/W D8h-D9h BIOS_DEC_EN1 BIOS Decode Enable 1 FFCFh R/W, RO DCh BIOS_CNTL 20h R/WLO, R/W, RO E0h-E1h FDCAP Feature Detection Capability ID 0009h RO E2h FDLEN Feature Detection Capability Length 0Ch RO BIOS Control E3h FDVER 10h RO E4h-E7h FVECIDX Feature Vector Index Feature Detection Version 00000000h R/W E8h-EBh FVECD Feature Vector Data See Description RO F0h-F3h RCBA Root Complex Base Address 00000000h R/W VID--Vendor Identification Register (LPC I/F--D31:F0) Bit 15:0 Attribute: RO Size: 16 bits Power Well:Core Description Vendor ID--RO. This is a 16-bit value assigned to Intel. Intel VID = 8086h DID--Device Identification Register (LPC I/F--D31:F0) Offset Address: 02h-03h Default Value: See bit description Lockable: No Bit 15:0 12.1.3 Attribute: RO Size: 16 bits Power Well:Core Description Device ID--RO. This is a 16-bit value assigned to the PCH LPC bridge. See Section 1.3 for the value of the DID Register. PCICMD--PCI COMMAND Register (LPC I/F--D31:F0) Offset Address: 04h-05h Default Value: 0007h Lockable: No Bit 15:10 380 Attribute LPC I/F Generic Decode Range 4 Offset Address: 00h-01h Default Value: 8086h Lockable: No 12.1.2 Default Attribute: R/W, RO Size: 16 bits Power Well:Core Description Reserved 9 Fast Back to Back Enable (FBE)--RO. Hardwired to 0. 8 SERR# Enable (SERR_EN)--R/W. The LPC bridge generates SERR# if this bit is set. Datasheet LPC Interface Bridge Registers (D31:F0) Bit 12.1.4 Description 7 Wait Cycle Control (WCC)--RO. Hardwired to 0. 6 Parity Error Response Enable (PERE)--R/W. 0 = No action is taken when detecting a parity error. 1 = Enables the PCH LPC bridge to respond to parity errors detected on backbone interface. 5 VGA Palette Snoop (VPS)--RO. Hardwired to 0. 4 Memory Write and Invalidate Enable (MWIE)--RO. Hardwired to 0. 3 Special Cycle Enable (SCE)--RO. Hardwired to 0. 2 Bus Master Enable (BME)--RO. Bus Masters cannot be disabled. 1 Memory Space Enable (MSE)--RO. Memory space cannot be disabled on LPC. 0 I/O Space Enable (IOSE)--RO. I/O space cannot be disabled on LPC. PCISTS--PCI Status Register (LPC I/F--D31:F0) Offset Address: 06h-07h Default Value: 0210h Lockable: No Note: For the writable bits, software must write a 1 to clear bits that are set. Writing a 0 to the bit has no effect. Bit Description 15 Detected Parity Error (DPE)--R/WC. Set when the LPC bridge detects a parity error on the internal backbone. Set even if the PCICMD.PERE bit (D31:F0:04, bit 6) is 0. 0 = Parity Error Not detected. 1 = Parity Error detected. 14 Signaled System Error (SSE)--R/WC. Set when the LPC bridge signals a system error to the internal SERR# logic. 13 Master Abort Status (RMA)--R/WC. 0 = Unsupported request status not received. 1 = The bridge received a completion with unsupported request status from the backbone. 12 Received Target Abort (RTA)--R/WC. 0 = Completion abort not received. 1 = Completion with completion abort received from the backbone. 11 Signaled Target Abort (STA)--R/WC. 0 = Target abort Not generated on the backbone. 1 = LPC bridge generated a completion packet with target abort status on the backbone. 10:9 DEVSEL# Timing Status (DEV_STS)--RO. 01 = Medium Timing. 8 Data Parity Error Detected (DPED)--R/WC. 0 = All conditions listed below Not met. 1 = Set when all three of the following conditions are met: * LPC bridge receives a completion packet from the backbone from a previous request, * Parity error has been detected (D31:F0:06, bit 15) * PCICMD.PERE bit (D31:F0:04, bit 6) is set. 7 Fast Back to Back Capable (FBC)--RO. Hardwired to 0. 6 Reserved 5 66 MHz Capable (66MHZ_CAP)--RO. Hardwired to 0. 4 Capabilities List (CLIST)--RO. Capability list exists on the LPC bridge. 3 Interrupt Status (IS)--RO. The LPC bridge does not generate interrupts. 2:0 Datasheet Attribute: RO, R/WC Size: 16 bits Power Well:Core Reserved 381 LPC Interface Bridge Registers (D31:F0) 12.1.5 RID--Revision Identification Register (LPC I/F--D31:F0) Offset Address: 08h Default Value: See bit description Bit 7:0 12.1.6 Attribute: Size: Description Revision ID (RID)--R/WO. This field indicates the device specific revision identifier. See Section 1.3 for the value of the RID Register. PI--Programming Interface Register (LPC I/F--D31:F0) Offset Address: 09h Default Value: 00h Bit 7:0 12.1.7 Attribute: Size: Programming Interface--RO. SCC--Sub Class Code Register (LPC I/F--D31:F0) Bit 7:0 Attribute: Size: Sub Class Code--RO. 8-bit value that indicates the category of bridge for the LPC bridge. 01h = PCI-to-ISA bridge. BCC--Base Class Code Register (LPC I/F--D31:F0) Bit 7:0 Attribute: Size: Base Class Code--RO. 8-bit value that indicates the type of device for the LPC bridge. 06h = Bridge device. PLT--Primary Latency Timer Register (LPC I/F--D31:F0) Bit Attribute: Size: RO 8-bit Description 7:3 Master Latency Count (MLC)--Reserved 2:0 Reserved HEADTYP--Header Type Register (LPC I/F--D31:F0) Offset Address: 0Eh Default Value: 80h Bit 7 6:0 382 RO 8-bit Description Offset Address: 0Dh Default Value: 00h 12.1.10 RO 8-bit Description Offset Address: 0Bh Default Value: 06h 12.1.9 RO 8 bits Description Offset Address: 0Ah Default Value: 01h 12.1.8 R/WO 8 bits Attribute: Size: RO 8-bit Description Multi-Function Device--RO. This bit is 1 to indicate a multi-function device. Header Type--RO. This 7-bit field identifies the header layout of the configuration space. Datasheet LPC Interface Bridge Registers (D31:F0) 12.1.11 SS--Sub System Identifiers Register (LPC I/F--D31:F0) Offset Address: 2Ch-2Fh Default Value: 00000000h Attribute: Size: R/WO 32 bits This register is initialized to logic 0 by the assertion of PLTRST#. This register can be written only once after PLTRST# de-assertion. Bit 31:16 15:0 12.1.12 Description Subsystem ID (SSID)--R/WO. This is written by BIOS. No hardware action taken on this value. Subsystem Vendor ID (SSVID)--R/WO. This is written by BIOS. No hardware action taken on this value. CAPP--Capability List Pointer Register (LPC I/F--D31:F0) Offset Address: 34h Default Value: E0h Bit 7:0 12.1.13 Attribute: Size: RO 8 bits Description Capability Pointer (CP)--RO. Indicates the offset of the first Capability Item. PMBASE--ACPI Base Address Register (LPC I/F--D31:F0) Offset Address: 40h-43h Default Value: 00000001h Lockable: No Attribute: R/W, RO Size: 32 bits Usage: ACPI, Legacy Power Well:Core Sets base address for ACPI I/O registers, GPIO registers and TCO I/O registers. These registers can be mapped anywhere in the 64-K I/O space on 128-byte boundaries. Bit 31:16 15:7 6:1 0 Datasheet Description Reserved Base Address--R/W. This field provides 128 bytes of I/O space for ACPI, GPIO, and TCO logic. This is placed on a 128-byte boundary. Reserved Resource Type Indicator (RTE)--RO. Hardwired to 1 to indicate I/O space. 383 LPC Interface Bridge Registers (D31:F0) 12.1.14 ACPI_CNTL--ACPI Control Register (LPC I/F--D31:F0) Offset Address: 44h Default Value: 00h Lockable: No Attribute: R/W Size: 8 bits Usage: ACPI, Legacy Power Well:Core Bit 7 Description ACPI Enable (ACPI_EN)--R/W. 0 = Disable. 1 = Decode of the I/O range pointed to by the ACPI base register is enabled, and the ACPI power management function is enabled. The APM power management ranges (B2/B3h) are always enabled and are not affected by this bit. 6:3 Reserved 2:0 SCI IRQ Select (SCI_IRQ_SEL)--R/W. Specifies on which IRQ the SCI will internally appear. If not using the APIC, the SCI must be routed to IRQ9-11, and that interrupt is not sharable with the SERIRQ stream, but is shareable with other PCI interrupts. If using the APIC, the SCI can also be mapped to IRQ20-23, and can be shared with other interrupts. Bits SCI Map 000b IRQ9 001b IRQ10 010b IRQ11 011b Reserved 100b IRQ20 (Only available if APIC enabled) 101b IRQ21 (Only available if APIC enabled) 110b IRQ22 (Only available if APIC enabled) 111b IRQ23 (Only available if APIC enabled) When the interrupt is mapped to APIC interrupts 9, 10 or 11, the APIC should be programmed for active-high reception. When the interrupt is mapped to APIC interrupts 20 through 23, the APIC should be programmed for active-low reception. 12.1.15 GPIOBASE--GPIO Base Address Register (LPC I/F-- D31:F0) Offset Address: 48h-4Bh Default Value: 00000001h Bit 31:16 15:7 6:1 0 384 Attribute: Size: R/W, RO 32 bits Description Reserved. Always 0. Base Address (BA)--R/W. Provides the 128 bytes of I/O space for GPIO. Reserved. Always 0. RO. Hardwired to 1 to indicate I/O space. Datasheet LPC Interface Bridge Registers (D31:F0) 12.1.16 GC--GPIO Control Register (LPC I/F--D31:F0) Offset Address: 4Ch Default Value: 00h Attribute: Size: Bit 7:5 4 3:1 0 12.1.17 Description Reserved GPIO Enable (EN)--R/W. This bit enables/disables decode of the I/O range pointed to by the GPIO Base Address register (D31:F0:48h) and enables the GPIO function. 0 = Disable. 1 = Enable. Reserved GPIO Lockdown Enable (GLE)--R/W. This bit enables lockdown of the following GPIO registers: * Offset 00h: GPIO_USE_SEL * Offset 04h: GP_IO_SEL * Offset 0Ch: GP_LVL * Offset 30h: GPIO_USE_SEL2 * Offset 34h: GP_IO_SEL2 * Offset 38h: GP_LVL2 * Offset 40h: GPIO_USE_SEL3 * Offset 44h: GP_IO_SEL3 * Offset 48h: GP_LVL3 * Offset 60h: GP_RST_SEL 0 = Disable. 1 = Enable. When this bit is written from 1-to-0, an SMI# is generated, if enabled. This ensures that only SMM code can change the above GPIO registers after they are locked down. PIRQ[n]_ROUT--PIRQ[A,B,C,D] Routing Control Register (LPC I/F--D31:F0) Offset Address: PIRQA - 60h, PIRQB - 61h, PIRQC - 62h, PIRQD - 63h Default Value: 80h Lockable: No Bit 7 Attribute: R/W Size: 8 bits Power Well:Core Description Interrupt Routing Enable (IRQEN)--R/W. 0 = The corresponding PIRQ is routed to one of the ISA-compatible interrupts specified in bits[3:0]. 1 = The PIRQ is not routed to the 8259. Note: BIOS must program this bit to 0 during POST for any of the PIRQs that are being used. The value of this bit may subsequently be changed by the OS when setting up for I/O APIC interrupt delivery mode. 6:4 Reserved 3:0 IRQ Routing--R/W. (ISA compatible.) Value Datasheet R/W 8 bits IRQ Value IRQ 0000b Reserved 1000b Reserved 0001b Reserved 1001b IRQ9 0010b Reserved 1010b IRQ10 0011b IRQ3 1011b IRQ11 0100b IRQ4 1100b IRQ12 0101b IRQ5 1101b Reserved 0110b IRQ6 1110b IRQ14 0111b IRQ7 1111b IRQ15 385 LPC Interface Bridge Registers (D31:F0) 12.1.18 SIRQ_CNTL--Serial IRQ Control Register (LPC I/F--D31:F0) Offset Address: 64h Default Value: 10h Lockable: No Attribute: R/W, RO Size: 8 bits Power Well:Core Bit Description 7 Serial IRQ Enable (SIRQEN)--R/W. 0 = The buffer is input only and internally SERIRQ will be a 1. 1 = Serial IRQs will be recognized. The SERIRQ pin will be configured as SERIRQ. 6 Serial IRQ Mode Select (SIRQMD)--R/W. 0 = The serial IRQ machine will be in quiet mode. 1 = The serial IRQ machine will be in continuous mode. Note: 12.1.19 For systems using Quiet Mode, this bit should be set to 1 (Continuous Mode) for at least one frame after coming out of reset before switching back to Quiet Mode. Failure to do so will result in the PCH not recognizing SERIRQ interrupts. 5:2 Serial IRQ Frame Size (SIRQSZ)--RO. Fixed field that indicates the size of the SERIRQ frame as 21 frames. 1:0 Start Frame Pulse Width (SFPW)--R/W. This is the number of PCI clocks that the SERIRQ pin will be driven low by the serial IRQ machine to signal a start frame. In continuous mode, the PCH will drive the start frame for the number of clocks specified. In quiet mode, the PCH will drive the start frame for the number of clocks specified minus one, as the first clock was driven by the peripheral. 00 = 4 clocks 01 = 6 clocks 10 = 8 clocks 11 = Reserved PIRQ[n]_ROUT--PIRQ[E,F,G,H] Routing Control Register (LPC I/F--D31:F0) Offset Address: PIRQE - 68h, PIRQF - 69h, PIRQG - 6Ah, PIRQH - 6Bh Default Value: 80h Lockable: No R/W Size: 8 bits Power Well:Core Bit Description 7 Interrupt Routing Enable (IRQEN)--R/W. 0 = The corresponding PIRQ is routed to one of the ISA-compatible interrupts specified in bits[3:0]. 1 = The PIRQ is not routed to the 8259. Note: BIOS must program this bit to 0 during POST for any of the PIRQs that are being used. The value of this bit may subsequently be changed by the OS when setting up for I/O APIC interrupt delivery mode. 6:4 Reserved 3:0 IRQ Routing--R/W. (ISA compatible.) Value 386 Attribute: Value IRQ 0000b Reserved IRQ 1000b Reserved 0001b Reserved 1001b IRQ9 0010b Reserved 1010b IRQ10 0011b IRQ3 1011b IRQ11 0100b IRQ4 1100b IRQ12 0101b IRQ5 1101b Reserved 0110b IRQ6 1110b IRQ14 0111b IRQ7 1111b IRQ15 Datasheet LPC Interface Bridge Registers (D31:F0) 12.1.20 LPC_IBDF--IOxAPIC Bus:Device:Function (LPC I/F--D31:F0) Offset Address: 6Ch-6Dh Default Value: 00F8h Attribute: Size: R/W 16 bits Bit Description 15:0 IOxAPIC Bus:Device:Function (IBDF)--R/W. this field specifies the bus:device:function that PCH's IOxAPIC will be using for the following: * As the Requester ID when initiating Interrupt Messages to the processor. * As the Completer ID when responding to the reads targeting the IOxAPIC's Memory-Mapped I/ O registers. The 16-bit field comprises the following: Bits 15:8 Description Bus Number 7:3 Device Number 2:0 Function Number This field defaults to Bus 0: Device 31: Function 0 after reset. BIOS can program this field to provide a unique bus:device:function number for the internal IOxAPIC. 12.1.21 LPC_HnBDF--HPET n Bus:Device:Function (LPC I/F--D31:F0) Address Offset Default Value: H0BDF H1BDF H2BDF H3BDF H4BDF H5BDF H6BDF H7BDF 00F8h 70h-71h 72h-73h 74h-75h 76h-77h 78h-79h 7Ah-7Bh 7Ch-7Dh 7Eh-7Fh Bit 15:0 Attribute: Size: R/W 16 bits Description HPET n Bus:Device:Function (HnBDF)--R/W. This field specifies the bus:device:function that the PCH's HPET n will be using in the following: * As the Requester ID when initiating Interrupt Messages to the processor * As the Completer ID when responding to the reads targeting the corresponding HPET's Memory-Mapped I/O registers The 16-bit field comprises the following: Bits 15:8 Description Bus Number 7:3 Device Number 2:0 Function Number This field is default to Bus 0: Device 31: Function 0 after reset. BIOS shall program this field accordingly if unique bus:device:function number is required for the corresponding HPET. Datasheet 387 LPC Interface Bridge Registers (D31:F0) 12.1.22 LPC_I/O_DEC--I/O Decode Ranges Register (LPC I/F--D31:F0) Offset Address: 80h Default Value: 0000h Bit 15:13 12 11:10 9:8 7 6:4 3 2:0 12.1.23 Attribute: Size: Description Reserved FDD Decode Range--R/W. Determines which range to decode for the FDD Port 0 = 3F0h-3F5h, 3F7h (Primary) 1 = 370h-375h, 377h (Secondary) Reserved LPT Decode Range--R/W. This field determines which range to decode for the LPT Port. 00 = 378h-37Fh and 778h-77Fh 01 = 278h-27Fh (port 279h is read only) and 678h-67Fh 10 = 3BCh -3BEh and 7BCh-7BEh 11 = Reserved Reserved COMB Decode Range--R/W. This field determines which range to decode for the COMB Port. 000 = 3F8h-3FFh (COM1) 001 = 2F8h-2FFh (COM2) 010 = 220h-227h 011 = 228h-22Fh 100 = 238h-23Fh 101 = 2E8h-2EFh (COM4) 110 = 338h-33Fh 111 = 3E8h-3EFh (COM3) Reserved COMA Decode Range--R/W. This field determines which range to decode for the COMA Port. 000 = 3F8h-3FFh (COM1) 001 = 2F8h-2FFh (COM2) 010 = 220h-227h 011 = 228h-22Fh 100 = 238h-23Fh 101 = 2E8h-2EFh (COM4) 110 = 338h-33Fh 111 = 3E8h-3EFh (COM3) LPC_EN--LPC I/F Enables Register (LPC I/F--D31:F0) Offset Address: 82h-83h Default Value: 0000h Bit 15:14 388 R/W 16 bits Attribute: R/W Size: 16 bits Power Well:Core Description Reserved 13 CNF2_LPC_EN--R/W. Microcontroller Enable #2. 0 = Disable. 1 = Enables the decoding of the I/O locations 4Eh and 4Fh to the LPC interface. This range is used for a microcontroller. 12 CNF1_LPC_EN--R/W. Super I/O Enable. 0 = Disable. 1 = Enables the decoding of the I/O locations 2Eh and 2Fh to the LPC interface. This range is used for Super I/O devices. Datasheet LPC Interface Bridge Registers (D31:F0) Bit Description 11 MC_LPC_EN--R/W. Microcontroller Enable # 1. 0 = Disable. 1 = Enables the decoding of the I/O locations 62h and 66h to the LPC interface. This range is used for a microcontroller. 10 KBC_LPC_EN--R/W. Keyboard Enable. 0 = Disable. 1 = Enables the decoding of the I/O locations 60h and 64h to the LPC interface. This range is used for a microcontroller. 9 GAMEH_LPC_EN--R/W. High Gameport Enable 0 = Disable. 1 = Enables the decoding of the I/O locations 208h to 20Fh to the LPC interface. This range is used for a gameport. 8 GAMEL_LPC_EN--R/W. Low Gameport Enable 0 = Disable. 1 = Enables the decoding of the I/O locations 200h to 207h to the LPC interface. This range is used for a gameport. 7:4 12.1.24 Reserved 3 FDD_LPC_EN--R/W. Floppy Drive Enable 0 = Disable. 1 = Enables the decoding of the FDD range to the LPC interface. This range is selected in the LPC_FDD/LPT Decode Range Register (D31:F0:80h, bit 12). 2 LPT_LPC_EN--R/W. Parallel Port Enable 0 = Disable. 1 = Enables the decoding of the LPTrange to the LPC interface. This range is selected in the LPC_FDD/LPT Decode Range Register (D31:F0:80h, bit 9:8). 1 COMB_LPC_EN--R/W. Com Port B Enable 0 = Disable. 1 = Enables the decoding of the COMB range to the LPC interface. This range is selected in the LPC_COM Decode Range Register (D31:F0:80h, bits 6:4). 0 COMA_LPC_EN--R/W. Com Port A Enable 0 = Disable. 1 = Enables the decoding of the COMA range to the LPC interface. This range is selected in the LPC_COM Decode Range Register (D31:F0:80h, bits 3:2). GEN1_DEC--LPC I/F Generic Decode Range 1 Register (LPC I/F--D31:F0) Offset Address: 84h-87h Default Value: 00000000h Bit Description 31:24 Reserved 23:18 Generic I/O Decode Range Address[7:2] Mask--R/W. A 1 in any bit position indicates that any value in the corresponding address bit in a received cycle will be treated as a match. The corresponding bit in the Address field, below, is ignored. The mask is only provided for the lower 6 bits of the DWord address, allowing for decoding blocks up to 256 bytes in size. 17:16 15:2 Datasheet Attribute: R/W Size: 32 bits Power Well:Core Reserved Generic I/O Decode Range 1 Base Address (GEN1_BASE)--R/W. Note: The PCH does not provide decode down to the word or byte level 1 Reserved 0 Generic Decode Range 1 Enable (GEN1_EN)--R/W. 0 = Disable. 1 = Enable the GEN1 I/O range to be forwarded to the LPC I/F 389 LPC Interface Bridge Registers (D31:F0) 12.1.25 GEN2_DEC--LPC I/F Generic Decode Range 2 Register (LPC I/F--D31:F0) Offset Address: 88h-8Bh Default Value: 00000000h Bit Description 31:24 Reserved 23:18 Generic I/O Decode Range Address[7:2] Mask--R/W. A 1 in any bit position indicates that any value in the corresponding address bit in a received cycle will be treated as a match. The corresponding bit in the Address field, below, is ignored. The mask is only provided for the lower 6 bits of the DWord address, allowing for decoding blocks up to 256 bytes in size. 17:16 15:2 12.1.26 Attribute: R/W Size: 32 bits Power Well:Core Reserved Generic I/O Decode Range 2 Base Address (GEN1_BASE)--R/W. Note: The PCH does not provide decode down to the word or byte level. 1 Reserved 0 Generic Decode Range 2 Enable (GEN2_EN)--R/W. 0 = Disable. 1 = Enable the GEN2 I/O range to be forwarded to the LPC I/F GEN3_DEC--LPC I/F Generic Decode Range 3 Register (LPC I/F--D31:F0) Offset Address: 8Ch-8Eh Default Value: 00000000h Bit Description 31:24 Reserved 23:18 Generic I/O Decode Range Address[7:2] Mask--R/W. A 1 in any bit position indicates that any value in the corresponding address bit in a received cycle will be treated as a match. The corresponding bit in the Address field, below, is ignored. The mask is only provided for the lower 6 bits of the DWord address, allowing for decoding blocks up to 256 bytes in size. 17:16 15:2 390 Attribute: R/W Size: 32 bits Power Well:Core Reserved Generic I/O Decode Range 3 Base Address (GEN3_BASE)--R/W. Note: The PCH Does not provide decode down to the word or byte level 1 Reserved 0 Generic Decode Range 3 Enable (GEN3_EN)--R/W. 0 = Disable. 1 = Enable the GEN3 I/O range to be forwarded to the LPC I/F Datasheet LPC Interface Bridge Registers (D31:F0) 12.1.27 GEN4_DEC--LPC I/F Generic Decode Range 4 Register (LPC I/F--D31:F0) Offset Address: 90h-93h Default Value: 00000000h Bit Description 31:24 Reserved 23:18 Generic I/O Decode Range Address[7:2] Mask--R/W. A 1 in any bit position indicates that any value in the corresponding address bit in a received cycle will be treated as a match. The corresponding bit in the Address field, below, is ignored. The mask is only provided for the lower 6 bits of the DWord address, allowing for decoding blocks up to 256 bytes in size. 17:16 15:2 12.1.28 Attribute: R/W Size: 32 bits Power Well:Core Reserved Generic I/O Decode Range 4 Base Address (GEN4_BASE)--R/W. Note: The PCH Does not provide decode down to the word or byte level 1 Reserved 0 Generic Decode Range 4 Enable (GEN4_EN)--R/W. 0 = Disable. 1 = Enable the GEN4 I/O range to be forwarded to the LPC I/F ULKMC--USB Legacy Keyboard / Mouse Control Register(LPC I/F--D31:F0) Offset Address: 94h-97h Default Value: 00002000h Bit 31:16 15 14:12 Datasheet Attribute: RO, R/WC, R/W Size: 32 bits Power Well:Core Description Reserved SMI Caused by End of Pass-Through (SMIBYENDPS)--R/WC. This bit indicates if the event occurred. Even if the corresponding enable bit is not set in bit 7, this bit will still be active. It is up to the SMM code to use the enable bit to determine the exact cause of the SMI#. 0 = Software clears this bit by writing a 1 to the bit location in any of the controllers. 1 = Event Occurred Reserved 11 SMI Caused by Port 64 Write (TRAPBY64W)--R/WC. This bit indicates if the event occurred. Even if the corresponding enable bit is not set in bit 3, this bit will still be active. It is up to the SMM code to use the enable bit to determine the exact cause of the SMI#. The A20Gate Pass-Through Logic allows specific port 64h writes to complete without setting this bit. 0 = Software clears this bit by writing a 1 to the bit location in any of the controllers. 1 = Event Occurred. 10 SMI Caused by Port 64 Read (TRAPBY64R)--R/WC. This bit indicates if the event occurred. Even if the corresponding enable bit is not set in bit 2, this bit will still be active. It is up to the SMM code to use the enable bit to determine the exact cause of the SMI#. 0 = Software clears this bit by writing a 1 to the bit location in any of the controllers. 1 = Event Occurred. 9 SMI Caused by Port 60 Write (TRAPBY60W)--R/WC. This bit indicates if the event occurred. Even if the corresponding enable bit is not set in bit 1, this bit will still be active. It is up to the SMM code to use the enable bit to determine the exact cause of the SMI#. The A20Gate Pass-Through Logic allows specific port 64h writes to complete without setting this bit. 0 = Software clears this bit by writing a 1 to the bit location in any of the controllers. 1 = Event Occurred. 391 LPC Interface Bridge Registers (D31:F0) 12.1.29 Bit Description 8 SMI Caused by Port 60 Read (TRAPBY60R)--R/WC. This bit indicates if the event occurred. Even if the corresponding enable bit is not set in the bit 0, this bit will still be active. It is up to the SMM code to use the enable bit to determine the exact cause of the SMI#. 0 = Software clears this bit by writing a 1 to the bit location in any of the controllers. 1 = Event Occurred. 7 SMI at End of Pass-Through Enable (SMIATENDPS)--R/W. This bit enables SMI at the end of a pass-through. This can occur if an SMI is generated in the middle of a pass-through, and needs to be serviced later. 0 = Disable 1 = Enable 6 Pass Through State (PSTATE)--RO. 0 = If software needs to reset this bit, it should set bit 5 in all of the host controllers to 0. 1 = Indicates that the state machine is in the middle of an A20GATE pass-through sequence. 5 A20Gate Pass-Through Enable (A20PASSEN)--R/W. 0 = Disable. 1 = Enable. Allows A20GATE sequence Pass-Through function. A specific cycle sequence involving writes to port 60h and 64h does not result in the setting of the SMI status bits. Note: A20M# functionality is not supported. 4 SMI on USB IRQ Enable (USBSMIEN)--R/W. 0 = Disable 1 = Enable. USB interrupt will cause an SMI event. 3 SMI on Port 64 Writes Enable (64WEN)--R/W. 0 = Disable 1 = Enable. A 1 in bit 11 will cause an SMI event. 2 SMI on Port 64 Reads Enable (64REN)--R/W. 0 = Disable 1 = Enable. A 1 in bit 10 will cause an SMI event. 1 SMI on Port 60 Writes Enable (60WEN)--R/W. 0 = Disable 1 = Enable. A 1 in bit 9 will cause an SMI event. 0 SMI on Port 60 Reads Enable (60REN)--R/W. 0 = Disable 1 = Enable. A 1 in bit 8 will cause an SMI event. LGMR--LPC I/F Generic Memory Range Register (LPC I/F--D31:F0) Offset Address: 98h-9Bh Default Value: 00000000h Bit Description 31:16 Memory Address[31:16]--R/W. This field specifies a 64 KB memory block anywhere in the 4 GB memory space that will be decoded to LPC as standard LPC memory cycle if enabled. 15:1 Reserved 0 392 Attribute: R/W Size: 32 bits Power Well:Core LPC Memory Range Decode Enable--R/W. When this bit is set to 1, then the range specified in bits 31:16 of this register is enabled for decoding to LPC. Datasheet LPC Interface Bridge Registers (D31:F0) 12.1.30 BIOS_SEL1--BIOS Select 1 Register (LPC I/F--D31:F0) Offset Address: D0h-D3h Default Value: 00112233h Bit Datasheet Attribute: Size: R/W, RO 32 bits Description 31:28 BIOS_F8_IDSEL--RO. IDSEL for two 512-KB BIOS memory ranges and one 128-KB memory range. This field is fixed at 0000. The IDSEL programmed in this field addresses the following memory ranges: FFF8 0000h-FFFF FFFFh FFB8 0000h-FFBF FFFFh 000E 0000h-000F FFFFh 27:24 BIOS_F0_IDSEL--R/W. IDSEL for two 512-KB BIOS memory ranges. The IDSEL programmed in this field addresses the following memory ranges: FFF0 0000h-FFF7 FFFFh FFB0 0000h-FFB7 FFFFh 23:20 BIOS_E8_IDSEL--R/W. IDSEL for two 512-KB BIOS memory ranges. The IDSEL programmed in this field addresses the following memory ranges: FFE8 0000h-FFEF FFFFh FFA8 0000h-FFAF FFFFh 19:16 BIOS_E0_IDSEL--R/W. IDSEL for two 512-KB BIOS memory ranges. The IDSEL programmed in this field addresses the following memory ranges: FFE0 0000h-FFE7 FFFFh FFA0 0000h-FFA7 FFFFh 15:12 BIOS_D8_IDSEL--R/W. IDSEL for two 512-KB BIOS memory ranges. The IDSEL programmed in this field addresses the following memory ranges: FFD8 0000h-FFDF FFFFh FF98 0000h-FF9F FFFFh 11:8 BIOS_D0_IDSEL--R/W. IDSEL for two 512-KB BIOS memory ranges. The IDSEL programmed in this field addresses the following memory ranges: FFD0 0000h-FFD7 FFFFh FF90 0000h-FF97 FFFFh 7:4 BIOS_C8_IDSEL--R/W. IDSEL for two 512-KB BIOS memory ranges. The IDSEL programmed in this field addresses the following memory ranges: FFC8 0000h-FFCF FFFFh FF88 0000h-FF8F FFFFh 3:0 BIOS_C0_IDSEL--R/W. IDSEL for two 512-KB BIOS memory ranges. The IDSEL programmed in this field addresses the following memory ranges: FFC0 0000h-FFC7 FFFFh FF80 0000h-FF87 FFFFh 393 LPC Interface Bridge Registers (D31:F0) 12.1.31 BIOS_SEL2--BIOS Select 2 Register (LPC I/F--D31:F0) Offset Address: D4h-D5h Default Value: 4567h 12.1.32 Attribute: Size: Bit Description 15:12 BIOS_70_IDSEL--R/W. IDSEL for two, 1-M BIOS memory ranges. The IDSEL programmed in this field addresses the following memory ranges: FF70 0000h-FF7F FFFFh FF30 0000h-FF3F FFFFh 11:8 BIOS_60_IDSEL--R/W. IDSEL for two, 1-M BIOS memory ranges. The IDSEL programmed in this field addresses the following memory ranges: FF60 0000h-FF6F FFFFh FF20 0000h-FF2F FFFFh 7:4 BIOS_50_IDSEL--R/W. IDSEL for two, 1-M BIOS memory ranges. The IDSEL programmed in this field addresses the following memory ranges: FF50 0000h-FF5F FFFFh FF10 0000h-FF1F FFFFh 3:0 BIOS_40_IDSEL--R/W. IDSEL for two, 1-M BIOS memory ranges. The IDSEL programmed in this field addresses the following memory ranges: FF40 0000h-FF4F FFFFh FF00 0000h-FF0F FFFFh BIOS_DEC_EN1--BIOS Decode Enable Register (LPC I/F--D31:F0) Offset Address: D8h-D9h Default Value: FFCFh Bit 394 R/W 16 bits Attribute: Size: R/W, RO 16 bits Description 15 BIOS_F8_EN--RO. This bit enables decoding two 512-KB BIOS memory ranges, and one 128-KB memory range. 0 = Disable 1 = Enable the following ranges for the BIOS FFF80000h-FFFFFFFFh FFB80000h-FFBFFFFFh 14 BIOS_F0_EN--R/W. This bit enables decoding two 512-KB BIOS memory ranges. 0 = Disable. 1 = Enable the following ranges for the BIOS: FFF00000h-FFF7FFFFh FFB00000h-FFB7FFFFh 13 BIOS_E8_EN--R/W. This bit enables decoding two 512-KB BIOS memory ranges. 0 = Disable. 1 = Enable the following ranges for the BIOS: FFE80000h-FFEFFFFh FFA80000h-FFAFFFFFh 12 BIOS_E0_EN--R/W. This bit enables decoding two 512-KB BIOS memory ranges. 0 = Disable. 1 = Enable the following ranges for the BIOS: FFE00000h-FFE7FFFFh FFA00000h-FFA7FFFFh 11 BIOS_D8_EN--R/W. This bit enables decoding two 512-KB BIOS memory ranges. 0 = Disable. 1 = Enable the following ranges for the BIOS FFD80000h-FFDFFFFFh FF980000h-FF9FFFFFh Datasheet LPC Interface Bridge Registers (D31:F0) Bit 10 BIOS_D0_EN--R/W. This bit enables decoding two 512-KB BIOS memory ranges. 0 = Disable. 1 = Enable the following ranges for the BIOS FFD00000h-FFD7FFFFh FF900000h-FF97FFFFh 9 BIOS_C8_EN--R/W. This bit enables decoding two 512-KB BIOS memory ranges. 0 = Disable. 1 = Enable the following ranges for the BIOS FFC80000h-FFCFFFFFh FF880000h-FF8FFFFFh 8 BIOS_C0_EN--R/W. This bit enables decoding two 512-KB BIOS memory ranges. 0 = Disable. 1 = Enable the following ranges for the BIOS FFC00000h-FFC7FFFFh FF800000h-FF87FFFFh 7 BIOS_Legacy_F_EN--R/W. This enables the decoding of the legacy 64KB range at F0000h- FFFFFh. 0 = Disable. 1 = Enable the following legacy ranges for the BIOS F0000h-FFFFFh Note: The decode for the BIOS legacy F segment is enabled only by this bit and is not affected by the GEN_PMCON_1.iA64_EN bit. 6 BIOS_Legacy_E_EN--R/W. This enables the decoding of the legacy 64KB range at E0000h- EFFFFh. 0 = Disable. 1 = Enable the following legacy ranges for the BIOS E0000h-EFFFFh Note: The decode for the BIOS legacy E segment is enabled only by this bit and is not affected by the GEN_PMCON_1.iA64_EN bit. 5:4 Reserved 3 BIOS_70_EN--R/W. Enables decoding two 1-M BIOS memory ranges. 0 = Disable. 1 = Enable the following ranges for the BIOS FF70 0000h-FF7F FFFFh FF30 0000h-FF3F FFFFh 2 BIOS_60_EN--R/W. Enables decoding two 1-M BIOS memory ranges. 0 = Disable. 1 = Enable the following ranges for the BIOS FF60 0000h-FF6F FFFFh FF20 0000h-FF2F FFFFh 1 BIOS_50_EN--R/W. Enables decoding two 1-M BIOS memory ranges. 0 = Disable. 1 = Enable the following ranges for the BIOS FF50 0000h-FF5F FFFFh FF10 0000h-FF1F FFFFh 0 BIOS_40_EN--R/W. Enables decoding two 1-M BIOS memory ranges. 0 = Disable. 1 = Enable the following ranges for the BIOS FF40 0000h-FF4F FFFFh FF00 0000h-FF0F FFFFh Note: Datasheet Description This register effects the BIOS decode regardless of whether the BIOS is resident on LPC or SPI. The concept of Feature Space does not apply to SPI-based flash. The PCH simply decodes these ranges as memory accesses when enabled for the SPI flash interface. 395 LPC Interface Bridge Registers (D31:F0) 12.1.33 BIOS_CNTL--BIOS Control Register (LPC I/F--D31:F0) Offset Address: DCh Default Value: 20h Lockable: No Attribute: R/WLO, R/W, RO Size: 8 bits Power Well:Core Bit 7:6 Description Reserved 5 SMM BIOS Write Protect Disable (SMM_BWP)--R/WL. This bit set defines when the BIOS region can be written by the host. 0 = BIOS region SMM protection is disabled. The BIOS Region is writable regardless if processors are in SMM or not. (Set this field to 0 for legacy behavior). 1 = BIOS region SMM protection is enabled. The BIOS Region is not writable unless all processors are in SMM and BIOS Write Enable (BIOSWE) is set to `1'. 4 Top Swap Status (TSS)--RO. This bit provides a read-only path to view the state of the Top Swap bit that is at offset 3414h, bit 0. 3:2 SPI Read Configuration (SRC)--R/W. This 2-bit field controls two policies related to BIOS reads on the SPI interface: Bit 3 - Prefetch Enable Bit 2 - Cache Disable Settings are summarized below: Bits 3:2 12.1.34 Description 00b No prefetching, but caching enabled. 64B demand reads load the read buffer cache with "valid" data, allowing repeated code fetches to the same line to complete quickly. 01b No prefetching and no caching. One-to-one correspondence of host BIOS reads to SPI cycles. This value can be used to invalidate the cache. 10b Prefetching and Caching enabled. This mode is used for long sequences of short reads to consecutive addresses (that is, shadowing). 11b Reserved. This is an invalid configuration, caching must be enabled when prefetching is enabled. 1 BIOS Lock Enable (BLE)--R/WLO. 0 = Transition of BIOSWE from `0' to `1' will not cause an SMI to be asserted. 1 = Enables setting the BIOSWE bit to cause SMIs and locks SMM_BWP. Once set, this bit can only be cleared by a PLTRST#. 0 BIOS Write Enable (BIOSWE)--R/W. 0 = Only read cycles result in Firmware Hub or SPI I/F cycles. 1 = Access to the BIOS space is enabled for both read and write cycles. When this bit is written from a 0 to a 1 and BIOS Lock Enable (BLE) is also set, an SMI# is generated. This ensures that only SMI code can update BIOS. FDCAP--Feature Detection Capability ID Register (LPC I/F--D31:F0) Offset Address: E0h-E1h Default Value: 0009h Bit 15:8 7:0 396 Attribute: RO Size: 16 bits Power Well:Core Description Next Item Pointer (NEXT)--RO. Configuration offset of the next Capability Item. 00h indicates the last item in the Capability List. Capability ID--RO. Indicates a Vendor Specific Capability Datasheet LPC Interface Bridge Registers (D31:F0) 12.1.35 FDLEN--Feature Detection Capability Length Register (LPC I/F--D31:F0) Offset Address: E2h Default Value: 0Ch 12.1.36 Attribute: RO Size: 8 bits Power Well:Core Bit Description 7:0 Capability Length--RO. Indicates the length of this Vendor Specific capability, as required by PCI Specification. FDVER--Feature Detection Version Register (LPC I/F--D31:F0) Offset Address: E3h Default Value: 10h Bit 12.1.37 Attribute: RO Size: 8 bits Power Well:Core Description 7:4 Vendor-Specific Capability ID--RO. A value of 1h in this 4-bit field identifies this Capability as Feature Detection Type. This field allows software to differentiate the Feature Detection Capability from other Vendor-Specific capabilities 3:0 Capability Version--RO. This field indicates the version of the Feature Detection capability FVECIDX--Feature Vector Index Register (LPC I/F--D31:F0) Offset Address: E4h-E7h Default Value: 00000000h Bit 31:6 12.1.38 Attribute: R/W Size: 32 bits Power Well:Core Description Reserved 5:2 Index (IDX)--R/W. 4-bit index pointer into the 64-byte Feature Vector space. Data is read from the FVECD register. This points to a DWord register. 1:0 Reserved FVECD--Feature Vector Data Register (LPC I/F--D31:F0) Offset Address: E8h-EBh Default Value: See Description Bit 31:0 Datasheet Attribute: RO Size: 32 bits Power Well:Core Description Data (DATA)--RO. 32-bit data value that is read from the Feature Vector offset pointed to by FVECIDX. 397 LPC Interface Bridge Registers (D31:F0) 12.1.39 Feature Vector Space 12.1.39.1 FVEC0--Feature Vector Register 0 FVECIDX.IDX: Default Value: 0000b See Description Bit 398 Description 31:12 Reserved 11:10 USB Port Count Capability--RO 00 = 14 ports 01 = 12 ports 10 = 10 ports 11 = Reserved 9:8 Attribute: RO Size: 32 bits Power Well:Core Reserved 7 RAID Capability Bit 1--RO See bit 5 Description. 6 SATA Ports 2 and 3--RO 0 = Capable 1 = Disabled 5 RAID Capability Bit 0--RO RAID Capability is defined by the combination of bits 7 and 5 of this register.: Bit 7 Bit 5 Capability 0 0 No RAID 0 1 RAID 1 1 0 RAID 0/1/5/10 1 1 RAID 0/1/5/10 and Intel Smart Response Technology 4 Reserved 3 SATA Port 1 6 Gb/s Capability--RO 0 = Capable 1 = Disabled 2 SATA Port 0 6 Gb/s Capability--RO 0 = Capable 1 = Disabled 1 PCI Interface Capability--RO 0 = Capable 1 = Disabled 0 Reserved Datasheet LPC Interface Bridge Registers (D31:F0) 12.1.39.2 FVEC1--Feature Vector Register 1 FVECIDX.IDX: Default Value: 0001b See Description Bit 31:23 22 21:0 12.1.39.3 Description Reserved USB Redirect (USBr) Capability--RO 0 = Capable 1 = Disabled Reserved FVEC2--Feature Vector Register 2 FVECIDX.IDX: Default Value: 0010b See Description Bit 31:23 Description Reserved Intel(R) Anti-Theft Technology Capability--RO 0 = Disabled 1 = Capable 21 PCI Express* Ports 7 and 8--RO 0 = Capable 1 = Disabled 17 16:0 Reserved PCH Integrated Graphics Support Capability--RO 0 = Capable 1 = Disabled Reserved FVEC3--Feature Vector Register 3 FVECIDX.IDX: Default Value: 0011b See Description Bit 31:14 Attribute: RO Size: 32 bits Power Well:Core Description Reserved 13 Data Center Manageability Interface (DCMI) Capability--RO 0 = Capable 1 = Disabled 12 Node Manager Capability--RO 0 = Capable 1 = Disabled 11:0 Datasheet Attribute: RO Size: 32 bits Power Well:Core 22 20:18 12.1.39.4 Attribute: RO Size: 32 bits Power Well:Core Reserved 399 LPC Interface Bridge Registers (D31:F0) 12.1.40 RCBA--Root Complex Base Address Register (LPC I/F--D31:F0) Offset Address: F0-F3h Default Value: 00000000h Bit 31:14 13:1 0 12.2 Attribute: Size: R/W 32 bits Description Base Address (BA)--R/W. Base Address for the root complex register block decode range. This address is aligned on a 16-KB boundary. Reserved Enable (EN)--R/W. When set, this bit enables the range specified in BA to be claimed as the Root Complex Register Block. DMA I/O Registers Table 12-2. DMA Registers (Sheet 1 of 2) Port Alias 00h 10h Register Name Default Type Channel 0 DMA Base and Current Address Undefined R/W 01h 11h Channel 0 DMA Base and Current Count Undefined R/W 02h 12h Channel 1 DMA Base and Current Address Undefined R/W 03h 13h Channel 1 DMA Base and Current Count Undefined R/W 04h 14h Channel 2 DMA Base and Current Address Undefined R/W 05h 15h Channel 2 DMA Base and Current Count Undefined R/W 06h 16h Channel 3 DMA Base and Current Address Undefined R/W 07h 17h Channel 3 DMA Base and Current Count Undefined R/W 08h 18h Channel 0-3 DMA Command Undefined WO Undefined RO 0Ah 1Ah Channel 0-3 DMA Write Single Mask 000001XXb WO 0Bh 1Bh Channel 0-3 DMA Channel Mode 000000XXb WO 0Ch 1Ch Channel 0-3 DMA Clear Byte Pointer Undefined WO 0Dh 1Dh Channel 0-3 DMA Master Clear Undefined WO 0Eh 1Eh Channel 0-3 DMA Clear Mask Undefined WO Channel 0-3 DMA Status 400 0Fh 1Fh Channel 0-3 DMA Write All Mask 0Fh R/W 80h 90h Reserved Page Undefined R/W 81h 91h Channel 2 DMA Memory Low Page Undefined R/W 82h -- Channel 3 DMA Memory Low Page Undefined R/W 83h 93h 84h-86h 94h-96h Channel 1 DMA Memory Low Page Undefined R/W Reserved Pages Undefined R/W 87h 97h Channel 0 DMA Memory Low Page Undefined R/W 88h 98h Reserved Page Undefined R/W 89h 99h Channel 6 DMA Memory Low Page Undefined R/W 8Ah 9Ah Channel 7 DMA Memory Low Page Undefined R/W 8Bh 9Bh 8Ch-8Eh 9Ch-9Eh Channel 5 DMA Memory Low Page Undefined R/W Reserved Page Undefined R/W Datasheet LPC Interface Bridge Registers (D31:F0) Table 12-2. DMA Registers (Sheet 2 of 2) Port Alias Register Name Default 8Fh 9Fh Refresh Low Page Undefined R/W C0h C1h Channel 4 DMA Base and Current Address Undefined R/W C2h C3h Channel 4 DMA Base and Current Count Undefined R/W C4h C5h Channel 5 DMA Base and Current Address Undefined R/W C6h C7h Channel 5 DMA Base and Current Count Undefined R/W C8h C9h Channel 6 DMA Base and Current Address Undefined R/W CAh CBh Channel 6 DMA Base and Current Count Undefined R/W CCh CDh Channel 7 DMA Base and Current Address Undefined R/W CEh CFh Channel 7 DMA Base and Current Count Undefined R/W D0h D1h Channel 4-7 DMA Command Undefined WO Undefined RO D4h D5h Channel 4-7 DMA Write Single Mask 000001XXb WO Channel 4-7 DMA Status 12.2.1 D6h D7h Channel 4-7 DMA Channel Mode 000000XXb WO D8h D9h Channel 4-7 DMA Clear Byte Pointer Undefined WO DAh dBh Channel 4-7 DMA Master Clear Undefined WO DCh DDh Channel 4-7 DMA Clear Mask Undefined WO DEh DFh Channel 4-7 DMA Write All Mask 0Fh R/W DMABASE_CA--DMA Base and Current Address Registers I/O Address: Ch. #0 = 00h; Ch. #1 = 02hAttribute: Ch. #2 = 04h; Ch. #3 = 06hSize: Ch. #5 = C4h Ch. #6 = C8h Ch. #7 = CCh; Default Value: Undefined Lockable: NoPower Well: Datasheet Type R/W 16 bits (per channel), but accessed in two 8-bit quantities Core Bit Description 15:0 Base and Current Address--R/W. This register determines the address for the transfers to be performed. The address specified points to two separate registers. On writes, the value is stored in the Base Address register and copied to the Current Address register. On reads, the value is returned from the Current Address register. The address increments/decrements in the Current Address register after each transfer, depending on the mode of the transfer. If the channel is in auto-initialize mode, the Current Address register will be reloaded from the Base Address register after a terminal count is generated. For transfers to/from a 16-bit slave (channels 5-7), the address is shifted left one bit location. Bit 15 will be shifted into Bit 16. The register is accessed in 8 bit quantities. The byte is pointed to by the current byte pointer flip/ flop. Before accessing an address register, the byte pointer flip/flop should be cleared to ensure that the low byte is accessed first. 401 LPC Interface Bridge Registers (D31:F0) 12.2.2 DMABASE_CC--DMA Base and Current Count Registers I/O Address: Ch. #0 = 01h; Ch. #1 = 03h Ch. #2 = 05h; Ch. #3 = 07hSize: Ch. #5 = C6h; Ch. #6 = CAh Ch. #7 = CEh; Default Value: Undefined Lockable: NoPower Well: 12.2.3 Core Bit Description 15:0 Base and Current Count--R/W. This register determines the number of transfers to be performed. The address specified points to two separate registers. On writes, the value is stored in the Base Count register and copied to the Current Count register. On reads, the value is returned from the Current Count register. The actual number of transfers is one more than the number programmed in the Base Count Register (that is, programming a count of 4h results in 5 transfers). The count is decrements in the Current Count register after each transfer. When the value in the register rolls from 0 to FFFFh, a terminal count is generated. If the channel is in auto-initialize mode, the Current Count register will be reloaded from the Base Count register after a terminal count is generated. For transfers to/from an 8-bit slave (channels 0-3), the count register indicates the number of bytes to be transferred. For transfers to/from a 16-bit slave (channels 5-7), the count register indicates the number of words to be transferred. The register is accessed in 8 bit quantities. The byte is pointed to by the current byte pointer flip/ flop. Before accessing a count register, the byte pointer flip/flop should be cleared to ensure that the low byte is accessed first. DMAMEM_LP--DMA Memory Low Page Registers I/O Address: Default Value: Lockable: 402 Attribute: R/W 16 bits (per channel), but accessed in two 8-bit quantities Ch. #0 = 87h; Ch. #1 = 83h Ch. #2 = 81h; Ch. #3 = 82h Ch. #5 = 8Bh; Ch. #6 = 89h Ch. #7 = 8Ah; Undefined No Attribute: R/W Size: 8 bits Power Well:Core Bit Description 7:0 DMA Low Page (ISA Address bits [23:16])--R/W. This register works in conjunction with the DMA controller's Current Address Register to define the complete 24-bit address for the DMA channel. This register remains static throughout the DMA transfer. Bit 16 of this register is ignored when in 16 bit I/O count by words mode as it is replaced by the bit 15 shifted out from the current address register. Datasheet LPC Interface Bridge Registers (D31:F0) 12.2.4 DMACMD--DMA Command Register I/O Address: Default Value: Lockable: Ch. #0-3 = 08h; Ch. #4-7 = D0h Undefined No Bit 7:5 4 Description Reserved. Must be 0. DMA Group Arbitration Priority--WO. Each channel group is individually assigned either fixed or rotating arbitration priority. At part reset, each group is initialized in fixed priority. 0 = Fixed priority to the channel group 1 = Rotating priority to the group. 3 Reserved. Must be 0. 2 DMA Channel Group Enable--WO. Both channel groups are enabled following part reset. 0 = Enable the DMA channel group. 1 = Disable. Disabling channel group 4-7 also disables channel group 0-3, which is cascaded through channel 4. 1:0 12.2.5 Reserved. Must be 0. DMASTA--DMA Status Register I/O Address: Default Value: Lockable: Bit Datasheet Attribute: WO Size: 8 bits Power Well:Core Ch. #0-3 = 08h; Ch. #4-7 = D0h Undefined No Attribute: RO Size: 8 bits Power Well:Core Description 7:4 Channel Request Status--RO. When a valid DMA request is pending for a channel, the corresponding bit is set to 1. When a DMA request is not pending for a particular channel, the corresponding bit is set to 0. The source of the DREQ may be hardware or a software request. Channel 4 is the cascade channel; thus, the request status of channel 4 is a logical OR of the request status for channels 0 through 3. 4 = Channel 0 5 = Channel 1 (5) 6 = Channel 2 (6) 7 = Channel 3 (7) 3:0 Channel Terminal Count Status--RO. When a channel reaches terminal count (TC), its status bit is set to 1. If TC has not been reached, the status bit is set to 0. Channel 4 is programmed for cascade; thus, the TC bit response for channel 4 is irrelevant: 0 = Channel 0 1 = Channel 1 (5) 2 = Channel 2 (6) 3 = Channel 3 (7) 403 LPC Interface Bridge Registers (D31:F0) 12.2.6 DMA_WRSMSK--DMA Write Single Mask Register I/O Address: Default Value: Lockable: Ch. #0-3 = 0Ah; Ch. #4-7 = D4h 0000 01xx No Bit 7:3 2 1:0 12.2.7 Description Reserved. Must be 0. Channel Mask Select--WO. 0 = Enable DREQ for the selected channel. The channel is selected through bits [1:0]. Therefore, only one channel can be masked / unmasked at a time. 1 = Disable DREQ for the selected channel. DMA Channel Select--WO. These bits select the DMA Channel Mode Register to program. 00 = Channel 0 (4) 01 = Channel 1 (5) 10 = Channel 2 (6) 11 = Channel 3 (7) DMACH_MODE--DMA Channel Mode Register I/O Address: Default Value: Lockable: 404 Attribute: WO Size: 8 bits Power Well:Core Ch. #0-3 = 0Bh; Ch. #4-7 = D6h 0000 00xx No Attribute: WO Size: 8 bits Power Well:Core Bit Description 7:6 DMA Transfer Mode--WO. Each DMA channel can be programmed in one of four different modes: 00 = Demand mode 01 = Single mode 10 = Reserved 11 = Cascade mode 5 Address Increment/Decrement Select--WO. This bit controls address increment/decrement during DMA transfers. 0 = Address increment. (default after part reset or Master Clear) 1 = Address decrement. 4 Autoinitialize Enable--WO. 0 = Autoinitialize feature is disabled and DMA transfers terminate on a terminal count. A part reset or Master Clear disables autoinitialization. 1 = DMA restores the Base Address and Count registers to the current registers following a terminal count (TC). 3:2 DMA Transfer Type--WO. These bits represent the direction of the DMA transfer. When the channel is programmed for cascade mode, (bits [7:6] = 11) the transfer type is irrelevant. 00 = Verify - No I/O or memory strobes generated 01 = Write - Data transferred from the I/O devices to memory 10 = Read - Data transferred from memory to the I/O device 11 = Invalid 1:0 DMA Channel Select--WO. These bits select the DMA Channel Mode Register that will be written by bits [7:2]. 00 = Channel 0 (4) 01 = Channel 1 (5) 10 = Channel 2 (6) 11 = Channel 3 (7) Datasheet LPC Interface Bridge Registers (D31:F0) 12.2.8 DMA Clear Byte Pointer Register I/O Address: Default Value: Lockable: 12.2.9 Ch. #0-3 = 0Ch; Ch. #4-7 = D8h xxxx xxxx No Bit Description 7:0 Clear Byte Pointer--WO. No specific pattern. Command enabled with a write to the I/O port address. Writing to this register initializes the byte pointer flip/flop to a known state. It clears the internal latch used to address the upper or lower byte of the 16-bit Address and Word Count Registers. The latch is also cleared by part reset and by the Master Clear command. This command precedes the first access to a 16-bit DMA controller register. The first access to a 16-bit register will then access the significant byte, and the second access automatically accesses the most significant byte. DMA Master Clear Register I/O Address: Default Value: Ch. #0-3 = 0Dh; Ch. #4-7 = DAh xxxx xxxx Bit 7:0 12.2.10 Attribute: Size: WO 8 bits Description Master Clear--WO. No specific pattern. Enabled with a write to the port. This has the same effect as the hardware Reset. The Command, Status, Request, and Byte Pointer flip/flop registers are cleared and the Mask Register is set. DMA_CLMSK--DMA Clear Mask Register I/O Address: Default Value: Lockable: Bit 7:0 Datasheet Attribute: WO Size: 8 bits Power Well:Core Ch. #0-3 = 0Eh; Ch. #4-7 = DCh xxxx xxxx No Attribute: WO Size: 8 bits Power Well:Core Description Clear Mask Register--WO. No specific pattern. Command enabled with a write to the port. 405 LPC Interface Bridge Registers (D31:F0) 12.2.11 DMA_WRMSK--DMA Write All Mask Register I/O Address: Default Value: Lockable: Ch. #0-3 = 0Fh; Ch. #4-7 = DEh 0000 1111 No Bit 12.3 Attribute: R/W Size: 8 bits Power Well:Core Description 7:4 Reserved. Must be 0. 3:0 Channel Mask Bits--R/W. This register permits all four channels to be simultaneously enabled/ disabled instead of enabling/disabling each channel individually, as is the case with the Mask Register - Write Single Mask Bit. In addition, this register has a read path to allow the status of the channel mask bits to be read. A channel's mask bit is automatically set to 1 when the Current Byte/ Word Count Register reaches terminal count (unless the channel is in auto-initialization mode). Setting the bit(s) to a 1 disables the corresponding DREQ(s). Setting the bit(s) to a 0 enables the corresponding DREQ(s). Bits [3:0] are set to 1 upon part reset or Master Clear. When read, bits [3:0] indicate the DMA channel [3:0] ([7:4]) mask status. Bit 0 = Channel 0 (4)1 = Masked, 0 = Not Masked Bit 1 = Channel 1 (5)1 = Masked, 0 = Not Masked Bit 2 = Channel 2 (6)1 = Masked, 0 = Not Masked Bit 3 = Channel 3 (7)1 = Masked, 0 = Not Masked Note: Disabling channel 4 also disables channels 0-3 due to the cascade of channels 0-3 through channel 4. Timer I/O Registers Port Aliases 40h 50h 41h 51h 42h 52h 43h 53h Register Name Counter 0 Interval Time Status Byte Format Counter 0 Counter Access Port Counter 1 Interval Time Status Byte Format Counter 1 Counter Access Port Type 0XXXXXXXb RO Undefined R/W 0XXXXXXXb RO Undefined R/W 0XXXXXXXb RO Counter 2 Counter Access Port Undefined R/W Timer Control Word Undefined WO XXXXXXX0b WO X0h WO Counter 2 Interval Time Status Byte Format Timer Control Word Register Counter Latch Command 406 Default Value Datasheet LPC Interface Bridge Registers (D31:F0) 12.3.1 TCW--Timer Control Word Register I/O Address: Default Value: 43h All bits undefined Attribute: Size: WO 8 bits This register is programmed prior to any counter being accessed to specify counter modes. Following part reset, the control words for each register are undefined and each counter output is 0. Each timer must be programmed to bring it into a known state. Bit Description 7:6 Counter Select--WO. The Counter Selection bits select the counter the control word acts upon as shown below. The Read Back Command is selected when bits[7:6] are both 1. 00 = Counter 0 select 01 = Counter 1 select 10 = Counter 2 select 11 = Read Back Command 5:4 Read/Write Select--WO. These bits are the read/write control bits. The actual counter programming is done through the counter port (40h for counter 0, 41h for counter 1, and 42h for counter 2). 00 = Counter Latch Command 01 = Read/Write Least Significant Byte (LSB) 10 = Read/Write Most Significant Byte (MSB) 11 = Read/Write LSB then MSB 3:1 Counter Mode Selection--WO. These bits select one of six possible modes of operation for the selected counter. Bit Value 0 Mode 000b Mode 0 Out signal on end of count (=0) 001b Mode 1 Hardware retriggerable one-shot x10b Mode 2 Rate generator (divide by n counter) x11b Mode 3 Square wave output 100b Mode 4 Software triggered strobe 101b Mode 5 Hardware triggered strobe Binary/BCD Countdown Select--WO. 0 = Binary countdown is used. The largest possible binary count is 216 1 = Binary coded decimal (BCD) count is used. The largest possible BCD count is 104 There are two special commands that can be issued to the counters through this register, the Read Back Command and the Counter Latch Command. When these commands are chosen, several bits within this register are redefined. These register formats are described as follows: RdBK_CMD--Read Back Command The Read Back Command is used to determine the count value, programmed mode, and current states of the OUT pin and Null count flag of the selected counter or counters. Status and/or count may be latched in any or all of the counters by selecting the counter during the register write. The count and status remain latched until read, and further latch commands are ignored until the count is read. Both count and status of the selected counters may be latched simultaneously by setting both bit 5 and bit 4 to 0. If both are latched, the first read operation from that counter returns the latched status. The next one or two reads, depending on whether the counter is programmed for one or two byte counts, returns the latched count. Subsequent reads return an unlatched count. Datasheet 407 LPC Interface Bridge Registers (D31:F0) Bit 7:6 Description Read Back Command. Must be 11 to select the Read Back Command 5 Latch Count of Selected Counters. 0 = Current count value of the selected counters will be latched 1 = Current count will not be latched 4 Latch Status of Selected Counters. 0 = Status of the selected counters will be latched 1 = Status will not be latched 3 Counter 2 Select. 1 = Counter 2 count and/or status will be latched 2 Counter 1 Select. 1 = Counter 1 count and/or status will be latched 1 Counter 0 Select. 1 = Counter 0 count and/or status will be latched. 0 Reserved. Must be 0. LTCH_CMD--Counter Latch Command The Counter Latch Command latches the current count value. This command is used to insure that the count read from the counter is accurate. The count value is then read from each counter's count register through the Counter Ports Access Ports Register (40h for counter 0, 41h for counter 1, and 42h for counter 2). The count must be read according to the programmed format; that is, if the counter is programmed for two byte counts, two bytes must be read. The two bytes do not have to be read one right after the other (read, write, or programming operations for other counters may be inserted between the reads). If a counter is latched once and then latched again before the count is read, the second Counter Latch Command is ignored. Bit 408 Description 7:6 Counter Selection. These bits select the counter for latching. If "11" is written, then the write is interpreted as a read back command. 00 = Counter 0 01 = Counter 1 10 = Counter 2 5:4 Counter Latch Command. 00 = Selects the Counter Latch Command. 3:0 Reserved. Must be 0. Datasheet LPC Interface Bridge Registers (D31:F0) 12.3.2 SBYTE_FMT--Interval Timer Status Byte Format Register I/O Address: Default Value: Counter 0 = 40h, Counter 1 = 41h, Counter 2 = 42h Bits[6:0] undefined, Bit 7=0 Attribute: Size: RO 8 bits per counter Each counter's status byte can be read following a Read Back Command. If latch status is chosen (bit 4=0, Read Back Command) as a read back option for a given counter, the next read from the counter's Counter Access Ports Register (40h for counter 0, 41h for counter 1, and 42h for counter 2) returns the status byte. The status byte returns the following: Bit 7 Counter OUT Pin State--RO. 0 = OUT pin of the counter is also a 0 1 = OUT pin of the counter is also a 1 6 Count Register Status--RO. This bit indicates when the last count written to the Count Register (CR) has been loaded into the counting element (CE). The exact time this happens depends on the counter mode, but until the count is loaded into the counting element (CE), the count value will be incorrect. 0 = Count has been transferred from CR to CE and is available for reading. 1 = Null Count. Count has not been transferred from CR to CE and is not yet available for reading. 5:4 Read/Write Selection Status--RO. These reflect the read/write selection made through bits[5:4] of the control register. The binary codes returned during the status read match the codes used to program the counter read/write selection. 00 = Counter Latch Command 01 = Read/Write Least Significant Byte (LSB) 10 = Read/Write Most Significant Byte (MSB) 11 = Read/Write LSB then MSB 3:1 Mode Selection Status--RO. These bits return the counter mode programming. The binary code returned matches the code used to program the counter mode, as listed under the bit function above. 000 = Mode 0 - Out signal on end of count (=0) 001 = Mode 1 - Hardware retriggerable one-shot x10 = Mode 2 - Rate generator (divide by n counter) x11 = Mode 3 - Square wave output 100 = Mode 4 - Software triggered strobe 101 = Mode 5 - Hardware triggered strobe 0 12.3.3 Description Countdown Type Status--RO. This bit reflects the current countdown type. 0 = Binary countdown 1 = Binary Coded Decimal (BCD) countdown. Counter Access Ports Register I/O Address: Default Value: Bit 7:0 Datasheet Counter 0 - 40h, Counter 1 - 41h, Counter 2 - 42h All bits undefined Attribute: R/W Size: 8 bits Description Counter Port--R/W. Each counter port address is used to program the 16-bit Count Register. The order of programming, either LSB only, MSB only, or LSB then MSB, is defined with the Interval Counter Control Register at port 43h. The counter port is also used to read the current count from the Count Register, and return the status of the counter programming following a Read Back Command. 409 LPC Interface Bridge Registers (D31:F0) 12.4 8259 Interrupt Controller (PIC) Registers 12.4.1 Interrupt Controller I/O MAP The interrupt controller registers are located at 20h and 21h for the master controller (IRQ 0-7), and at A0h and A1h for the slave controller (IRQ 8-13). These registers have multiple functions, depending upon the data written to them. Table 12-3 shows the different register possibilities for each address. Table 12-3. PIC Registers Port Aliases 20h 24h, 28h, 2Ch, 30h, 34h, 38h, 3Ch Master PIC ICW1 Init. Cmd Word 1 25h, 29h, 2Dh, 31h, 35h, 39h, 3Dh 21h A0h Register Name Default Value Type Undefined WO Master PIC OCW2 Op Ctrl Word 2 001XXXXXb WO Master PIC OCW3 Op Ctrl Word 3 X01XXX10b WO Master PIC ICW2 Init. Cmd Word 2 Undefined WO Master PIC ICW3 Init. Cmd Word 3 Undefined WO Master PIC ICW4 Init. Cmd Word 4 01h WO Master PIC OCW1 Op Ctrl Word 1 00h R/W A4h, A8h, ACh, B0h, B4h, B8h, BCh Slave PIC ICW1 Init. Cmd Word 1 A5h, A9h, ADh, B1h, B5h, B9h, BDh Slave PIC ICW2 Init. Cmd Word 2 Slave PIC ICW3 Init. Cmd Word 3 Undefined WO Slave PIC ICW4 Init. Cmd Word 4 01h WO Slave PIC OCW1 Op Ctrl Word 1 00h R/W 4D0h - Master PIC Edge/Level Triggered 00h R/W 4D1h - Slave PIC Edge/Level Triggered 00h R/W A1h Undefined WO Slave PIC OCW2 Op Ctrl Word 2 001XXXXXb WO Slave PIC OCW3 Op Ctrl Word 3 X01XXX10b WO Undefined WO Note: Refer to note addressing active-low interrupt sources in 8259 Interrupt Controllers section (Chapter 5.9). 12.4.2 ICW1--Initialization Command Word 1 Register Offset Address: Master Controller - 20h Slave Controller - A0h Default Value: All bits undefined Attribute: Size: WO 8 bits /controller A write to Initialization Command Word 1 starts the interrupt controller initialization sequence, during which the following occurs: 1. The Interrupt Mask register is cleared. 2. IRQ7 input is assigned priority 7. 3. The slave mode address is set to 7. 4. Special mask mode is cleared and Status Read is set to IRR. Once this write occurs, the controller expects writes to ICW2, ICW3, and ICW4 to complete the initialization sequence. 410 Datasheet LPC Interface Bridge Registers (D31:F0) Bit 7:5 12.4.3 Description ICW/OCW Select--WO. These bits are MCS-85 specific, and not needed. 000 = Should be programmed to "000" 4 ICW/OCW Select--WO. 1 = This bit must be a 1 to select ICW1 and enable the ICW2, ICW3, and ICW4 sequence. 3 Edge/Level Bank Select (LTIM)--WO. Disabled. Replaced by the edge/level triggered control registers (ELCR, D31:F0:4D0h, D31:F0:4D1h). 2 ADI--WO. 0 = Ignored for the PCH. Should be programmed to 0. 1 Single or Cascade (SNGL)--WO. 0 = Must be programmed to a 0 to indicate two controllers operating in cascade mode. 0 ICW4 Write Required (IC4)--WO. 1 = This bit must be programmed to a 1 to indicate that ICW4 needs to be programmed. ICW2--Initialization Command Word 2 Register Offset Address: Master Controller - 21h Slave Controller - A1h Default Value: All bits undefined Attribute: Size: WO 8 bits /controller ICW2 is used to initialize the interrupt controller with the five most significant bits of the interrupt vector address. The value programmed for bits[7:3] is used by the processor to define the base address in the interrupt vector table for the interrupt routines associated with each IRQ on the controller. Typical ISA ICW2 values are 08h for the master controller and 70h for the slave controller. Bit Datasheet Description 7:3 Interrupt Vector Base Address--WO. Bits [7:3] define the base address in the interrupt vector table for the interrupt routines associated with each interrupt request level input. 2:0 Interrupt Request Level--WO. When writing ICW2, these bits should all be 0. During an interrupt acknowledge cycle, these bits are programmed by the interrupt controller with the interrupt to be serviced. This is combined with bits [7:3] to form the interrupt vector driven onto the data bus during the second INTA# cycle. The code is a three bit binary code: Code Master Interrupt Slave Interrupt 000b IRQ0 IRQ8 001b IRQ1 IRQ9 010b IRQ2 IRQ10 011b IRQ3 IRQ11 100b IRQ4 IRQ12 101b IRQ5 IRQ13 110b IRQ6 IRQ14 411 LPC Interface Bridge Registers (D31:F0) 12.4.4 ICW3--Master Controller Initialization Command Word 3 Register Offset Address: 21h Default Value: All bits undefined Bit 7:3 2 1:0 12.4.5 Attribute: Size: Description 0 = These bits must be programmed to 0. Cascaded Interrupt Controller IRQ Connection--WO. This bit indicates that the slave controller is cascaded on IRQ2. When IRQ8#-IRQ15 is asserted, it goes through the slave controller's priority resolver. The slave controller's INTR output onto IRQ2. IRQ2 then goes through the master controller's priority solver. If it wins, the INTR signal is asserted to the processor, and the returning interrupt acknowledge returns the interrupt vector for the slave controller. 1 = This bit must always be programmed to a 1. 0 = These bits must be programmed to 0. ICW3--Slave Controller Initialization Command Word 3 Register Offset Address: A1h Default Value: All bits undefined Bit 12.4.6 Attribute: Size: WO 8 bits Description 7:3 0 = These bits must be programmed to 0. 2:0 Slave Identification Code--WO. These bits are compared against the slave identification code broadcast by the master controller from the trailing edge of the first internal INTA# pulse to the trailing edge of the second internal INTA# pulse. These bits must be programmed to 02h to match the code broadcast by the master controller. When 02h is broadcast by the master controller during the INTA# sequence, the slave controller assumes responsibility for broadcasting the interrupt vector. ICW4--Initialization Command Word 4 Register Offset Address: Master Controller - 021h Slave Controller - 0A1h Default Value: 01h Bit 7:5 412 WO 8 bits Attribute: Size: WO 8 bits Description 0 = These bits must be programmed to 0. 4 Special Fully Nested Mode (SFNM)--WO. 0 = Should normally be disabled by writing a 0 to this bit. 1 = Special fully nested mode is programmed. 3 Buffered Mode (BUF)--WO. 0 = Must be programmed to 0 for the PCH. This is non-buffered mode. 2 Master/Slave in Buffered Mode--WO. Not used. 0 = Should always be programmed to 0. 1 Automatic End of Interrupt (AEOI)--WO. 0 = This bit should normally be programmed to 0. This is the normal end of interrupt. 1 = Automatic End of Interrupt (AEOI) mode is programmed. 0 Microprocessor Mode--WO. 1 = Must be programmed to 1 to indicate that the controller is operating in an Intel Architecture-based system. Datasheet LPC Interface Bridge Registers (D31:F0) 12.4.7 OCW1--Operational Control Word 1 (Interrupt Mask) Register Offset Address: Master Controller - 021h Slave Controller - 0A1h Default Value: 00h 12.4.8 Attribute: Size: R/W 8 bits Bit Description 7:0 Interrupt Request Mask--R/W. When a 1 is written to any bit in this register, the corresponding IRQ line is masked. When a 0 is written to any bit in this register, the corresponding IRQ mask bit is cleared, and interrupt requests will again be accepted by the controller. Masking IRQ2 on the master controller will also mask the interrupt requests from the slave controller. OCW2--Operational Control Word 2 Register Offset Address: Master Controller - 020h Slave Controller - 0A0h Default Value: Bit[4:0]=undefined, Bit[7:5]=001 Attribute: Size: WO 8 bits Following a part reset or ICW initialization, the controller enters the fully nested mode of operation. Non-specific EOI without rotation is the default. Both rotation mode and specific EOI mode are disabled following initialization. Datasheet Bit Description 7:5 Rotate and EOI Codes (R, SL, EOI)--WO. These three bits control the Rotate and End of Interrupt modes and combinations of the two. 000 = Rotate in Auto EOI Mode (Clear) 001 = Non-specific EOI command 010 = No Operation 011 = *Specific EOI Command 100 = Rotate in Auto EOI Mode (Set) 101 = Rotate on Non-Specific EOI Command 110 = *Set Priority Command 111 = *Rotate on Specific EOI Command *L0 - L2 Are Used 4:3 OCW2 Select--WO. When selecting OCW2, bits 4:3 = 00 2:0 Interrupt Level Select (L2, L1, L0)--WO. L2, L1, and L0 determine the interrupt level acted upon when the SL bit is active. A simple binary code, outlined below, selects the channel for the command to act upon. When the SL bit is inactive, these bits do not have a defined function; programming L2, L1 and L0 to 0 is sufficient in this case. Code Interrupt Level Code Interrupt Level 000b IRQ0/8 000b IRQ4/12 001b IRQ1/9 001b IRQ5/13 010b IRQ2/10 010b IRQ6/14 011b IRQ3/11 011b IRQ7/15 413 LPC Interface Bridge Registers (D31:F0) 12.4.9 OCW3--Operational Control Word 3 Register Offset Address: Master Controller - 020h Slave Controller - 0A0h Default Value: Bit[6,0]=0, Bit[7,4:2]=undefined, Bit[5,1]=1 Bit WO 8 bits Description 7 Reserved. Must be 0. 6 Special Mask Mode (SMM)--WO. 1 = The Special Mask Mode can be used by an interrupt service routine to dynamically alter the system priority structure while the routine is executing, through selective enabling/disabling of the other channel's mask bits. Bit 5, the ESMM bit, must be set for this bit to have any meaning. 5 Enable Special Mask Mode (ESMM)--WO. 0 = Disable. The SMM bit becomes a "don't care". 1 = Enable the SMM bit to set or reset the Special Mask Mode. 4:3 2 1:0 414 Attribute: Size: OCW3 Select--WO. When selecting OCW3, bits 4:3 = 01 Poll Mode Command--WO. 0 = Disable. Poll Command is not issued. 1 = Enable. The next I/O read to the interrupt controller is treated as an interrupt acknowledge cycle. An encoded byte is driven onto the data bus, representing the highest priority level requesting service. Register Read Command--WO. These bits provide control for reading the In-Service Register (ISR) and the Interrupt Request Register (IRR). When bit 1=0, bit 0 will not affect the register read selection. When bit 1=1, bit 0 selects the register status returned following an OCW3 read. If bit 0=0, the IRR will be read. If bit 0=1, the ISR will be read. Following ICW initialization, the default OCW3 port address read will be "read IRR". To retain the current selection (read ISR or read IRR), always write a 0 to bit 1 when programming this register. The selected register can be read repeatedly without reprogramming OCW3. To select a new status register, OCW3 must be reprogrammed prior to attempting the read. 00 = No Action 01 = No Action 10 = Read IRQ Register 11 = Read IS Register Datasheet LPC Interface Bridge Registers (D31:F0) 12.4.10 ELCR1--Master Controller Edge/Level Triggered Register Offset Address: 4D0h Default Value: 00h Attribute: Size: R/W 8 bits In edge mode, (bit[x] = 0), the interrupt is recognized by a low to high transition. In level mode (bit[x] = 1), the interrupt is recognized by a high level. The cascade channel, IRQ2, the heart beat timer (IRQ0), and the keyboard controller (IRQ1), cannot be put into level mode. Bit 7 IRQ7 ECL--R/W. 0 = Edge 1 = Level 6 IRQ6 ECL--R/W. 0 = Edge 1 = Level. 5 IRQ5 ECL--R/W. 0 = Edge 1 = Level 4 IRQ4 ECL--R/W. 0 = Edge 1 = Level 3 IRQ3 ECL--R/W. 0 = Edge 1 = Level 2:0 Datasheet Description Reserved. Must be 0. 415 LPC Interface Bridge Registers (D31:F0) 12.4.11 ELCR2--Slave Controller Edge/Level Triggered Register Offset Address: 4D1h Default Value: 00h Attribute: Size: R/W 8 bits In edge mode, (bit[x] = 0), the interrupt is recognized by a low to high transition. In level mode (bit[x] = 1), the interrupt is recognized by a high level. The real time clock, IRQ8#, and the floating point error interrupt, IRQ13, cannot be programmed for level mode. Bit 416 Description 7 IRQ15 ECL--R/W. 0 = Edge 1 = Level 6 IRQ14 ECL--R/W. 0 = Edge 1 = Level 5 Reserved. Must be 0. 4 IRQ12 ECL--R/W. 0 = Edge 1 = Level 3 IRQ11 ECL--R/W. 0 = Edge 1 = Level 2 IRQ10 ECL--R/W. 0 = Edge 1 = Level 1 IRQ9 ECL--R/W. 0 = Edge 1 = Level 0 Reserved. Must be 0. Datasheet LPC Interface Bridge Registers (D31:F0) 12.5 Advanced Programmable Interrupt Controller (APIC) 12.5.1 APIC Register Map The APIC is accessed using an indirect addressing scheme. Two registers are visible by software for manipulation of most of the APIC registers. These registers are mapped into memory space. The address bits 19:12 of the address range are programmable through bits 7:0 of OIC register (Chipset Config Registers:Offset 31FEh) The registers are shown in Table 12-4. Table 12-4. APIC Direct Registers Address Mnemonic Register Name Size Type FEC_ _0000h IND FEC_ _0010h DAT Index 8 bits R/W Data 32 bits R/W FEC_ _0040h EOIR EOI 32 bits WO Table 12-5 lists the registers that can be accessed within the APIC using the Index Register. When accessing these registers, accesses must be done one DWord at a time. For example, software should never access byte 2 from the Data register before accessing bytes 0 and 1. The hardware will not attempt to recover from a bad programming model in this case. Table 12-5. APIC Indirect Registers 12.5.2 Index Mnemonic 00 ID Register Name Size Type Identification 32 bits R/W Version 32 bits RO -- RO 01 VER 02-0F -- 10-11 REDIR_TBL0 Redirection Table 0 64 bits R/W, RO 12-13 REDIR_TBL1 Redirection Table 1 64 bits R/W, RO ... ... 3E-3F REDIR_TBL23 40-FF -- Reserved ... Redirection Table 23 Reserved ... ... 64 bits R/W, RO -- RO IND--Index Register Memory Address FEC_ _0000h Default Value: 00h Attribute: Size: R/W 8 bits The Index Register will select which APIC indirect register to be manipulated by software. The selector values for the indirect registers are listed in Table 12-5. Software will program this register to select the desired APIC internal register. . Bit 7:0 Datasheet Description APIC Index--R/W. This is an 8-bit pointer into the I/O APIC register table. 417 LPC Interface Bridge Registers (D31:F0) 12.5.3 DAT--Data Register Memory Address FEC_ _0000h Default Value: 00000000h Attribute: Size: R/W 32 bits This is a 32-bit register specifying the data to be read or written to the register pointed to by the Index register. This register can only be accessed in DWord quantities. Bit 7:0 12.5.4 Description APIC Data--R/W. This is a 32-bit register for the data to be read or written to the APIC indirect register (Figure 12-5) pointed to by the Index register (Memory Address FEC0_0000h). EOIR--EOI Register Memory Address FEC_ _0000h Default Value: N/A Attribute: Size: R/W 32 bits The EOI register is present to provide a mechanism to maintain the level triggered semantics for level-triggered interrupts issued on the parallel bus. When a write is issued to this register, the I/O APIC will check the lower 8 bits written to this register, and compare it with the vector field for each entry in the I/O Redirection Table. When a match is found, the Remote_IRR bit (Index Offset 10h, bit 14) for that I/O Redirection Entry will be cleared. Note: If multiple I/O Redirection entries, for any reason, assign the same vector for more than one interrupt input, each of those entries will have the Remote_IRR bit reset to 0. The interrupt, which was prematurely reset, will not be lost because if its input remained active when the Remote_IRR bit was cleared, the interrupt will be reissued and serviced at a later time. Only bits 7:0 are actually used. Bits 31:8 are ignored by the PCH. Note: To provide for future expansion, the processor should always write a value of 0 to Bits 31:8. Bit 31:8 7:0 418 Description Reserved. To provide for future expansion, the processor should always write a value of 0 to Bits 31:8. Redirection Entry Clear--WO. When a write is issued to this register, the I/O APIC will check this field, and compare it with the vector field for each entry in the I/O Redirection Table. When a match is found, the Remote_IRR bit for that I/O Redirection Entry will be cleared. Datasheet LPC Interface Bridge Registers (D31:F0) 12.5.5 ID--Identification Register Index Offset: Default Value: 00h 00000000h Attribute: Size: R/W 32 bits The APIC ID serves as a physical name of the APIC. The APIC bus arbitration ID for the APIC is derived from its I/O APIC ID. This register is reset to 0 on power-up reset. Bit 31:28 Reserved 27:24 APIC ID--R/W. Software must program this value before using the APIC. 23:16 Reserved 15 14:0 12.5.6 Description Scratchpad Bit. Reserved VER--Version Register Index Offset: Default Value: 01h 00170020h Attribute: Size: RO, R/WO 32 bits Each I/O APIC contains a hardwired Version Register that identifies different implementation of APIC and their versions. The maximum redirection entry information also is in this register, to let software know how many interrupt are supported by this APIC. Bit 31:24 Reserved 23:16 Maximum Redirection Entries (MRE)--R/WO. This is the entry number (0 being the lowest entry) of the highest entry in the redirection table. It is equal to the number of interrupt input pins minus one and is in the range 0 through 239. In the PCH this field is hardwired to 17h to indicate 24 interrupts. BIOS must write to this field after PLTRST# to lockdown the value. this allows BIOS to utilize some of the entries for its own purpose and thus advertising fewer IOxAPIC Redirection Entries to the OS. 15 14:8 7:0 Datasheet Description Pin Assertion Register Supported (PRQ)--RO. Indicate that the IOxAPIC does not implement the Pin Assertion Register. Reserved Version (VS)--RO. This is a version number that identifies the implementation version. 419 LPC Interface Bridge Registers (D31:F0) 12.5.7 REDIR_TBL--Redirection Table Register Index Offset: Default Value: 10h-11h (vector 0) through 3E-3Fh (vector 23) Bit 16 = 1. All other bits undefined Attribute: R/W, RO Size: 64 bits each, (accessed as two 32-bit quantities) The Redirection Table has a dedicated entry for each interrupt input pin. The information in the Redirection Table is used to translate the interrupt manifestation on the corresponding interrupt pin into an APIC message. The APIC will respond to an edge triggered interrupt as long as the interrupt is held until after the acknowledge cycle has begun. Once the interrupt is detected, a delivery status bit internally to the I/O APIC is set. The state machine will step ahead and wait for an acknowledgment from the APIC unit that the interrupt message was sent. Only then will the I/O APIC be able to recognize a new edge on that interrupt pin. That new edge will only result in a new invocation of the handler if its acceptance by the destination APIC causes the Interrupt Request Register bit to go from 0 to 1. (In other words, if the interrupt was not already pending at the destination.) 420 Bit Description 63:56 Destination--R/W. If bit 11 of this entry is 0 (Physical), then bits 59:56 specifies an APIC ID. In this case, bits 63:59 should be programmed by software to 0. If bit 11 of this entry is 1 (Logical), then bits 63:56 specify the logical destination address of a set of processors. 55:48 Extended Destination ID (EDID)--RO. These bits are sent to a local APIC only when in Processor System Bus mode. They become bits 11:4 of the address. 47:17 Reserved 16 Mask--R/W. 0 = Not masked: An edge or level on this interrupt pin results in the delivery of the interrupt to the destination. 1 = Masked: Interrupts are not delivered nor held pending. Setting this bit after the interrupt is accepted by a local APIC has no effect on that interrupt. This behavior is identical to the device withdrawing the interrupt before it is posted to the processor. It is software's responsibility to deal with the case where the mask bit is set after the interrupt message has been accepted by a local APIC unit but before the interrupt is dispensed to the processor. 15 Trigger Mode--R/W. This field indicates the type of signal on the interrupt pin that triggers an interrupt. 0 = Edge triggered. 1 = Level triggered. 14 Remote IRR--R/W. This bit is used for level triggered interrupts; its meaning is undefined for edge triggered interrupts. 0 = Reset when an EOI message is received from a local APIC. 1 = Set when Local APIC/s accept the level interrupt sent by the I/O APIC. 13 Interrupt Input Pin Polarity--R/W. This bit specifies the polarity of each interrupt signal connected to the interrupt pins. 0 = Active high. 1 = Active low. 12 Delivery Status--RO. This field contains the current status of the delivery of this interrupt. Writes to this bit have no effect. 0 = Idle. No activity for this interrupt. 1 = Pending. Interrupt has been injected, but delivery is not complete. 11 Destination Mode--R/W. This field determines the interpretation of the Destination field. 0 = Physical. Destination APIC ID is identified by bits 59:56. 1 = Logical. Destinations are identified by matching bit 63:56 with the Logical Destination in the Destination Format Register and Logical Destination Register in each Local APIC. Datasheet LPC Interface Bridge Registers (D31:F0) Bit 10:8 7:0 Description Delivery Mode--R/W. This field specifies how the APICs listed in the destination field should act upon reception of this signal. Certain Delivery Modes will only operate as intended when used in conjunction with a specific trigger mode. These encodings are listed in the note below: Vector--R/W. This field contains the interrupt vector for this interrupt. Values range between 10h and FEh. Note: Delivery Mode encoding: 000 = Fixed. Deliver the signal on the INTR signal of all processor cores listed in the destination. Trigger Mode can be edge or level. 001 = Lowest Priority. Deliver the signal on the INTR signal of the processor core that is executing at the lowest priority among all the processors listed in the specified destination. Trigger Mode can be edge or level. 010 = SMI (System Management Interrupt). Requires the interrupt to be programmed as edge triggered. The vector information is ignored but must be programmed to all 0s for future compatibility: not supported 011 = Reserved 100 = NMI. Deliver the signal on the NMI signal of all processor cores listed in the destination. Vector information is ignored. NMI is treated as an edge triggered interrupt even if it is programmed as level triggered. For proper operation this redirection table entry must be programmed to edge triggered. The NMI delivery mode does not set the RIRR bit. If the redirection table is incorrectly set to level, the loop count will continue counting through the redirection table addresses. Once the count for the NMI pin is reached again, the interrupt will be sent again: not supported 101 = INIT. Deliver the signal to all processor cores listed in the destination by asserting the INIT signal. All addressed local APICs will assume their INIT state. INIT is always treated as an edge triggered interrupt even if programmed as level triggered. For proper operation this redirection table entry must be programmed to edge triggered. The INIT delivery mode does not set the RIRR bit. If the redirection table is incorrectly set to level, the loop count will continue counting through the redirection table addresses. Once the count for the INIT pin is reached again, the interrupt will be sent again: not supported 110 = Reserved 111 = ExtINT. Deliver the signal to the INTR signal of all processor cores listed in the destination as an interrupt that originated in an externally connected 8259A compatible interrupt controller. The INTA cycle that corresponds to this ExtINT delivery will be routed to the external controller that is expected to supply the vector. Requires the interrupt to be programmed as edge triggered. 12.6 Real Time Clock Registers 12.6.1 I/O Register Address Map The RTC internal registers and RAM are organized as two banks of 128 bytes each, called the standard and extended banks. The first 14 bytes of the standard bank contain the RTC time and date information along with four registers, A-D, that are used for configuration of the RTC. The extended bank contains a full 128 bytes of battery backed SRAM, and will be accessible even when the RTC module is disabled (using the RTC configuration register). Registers A-D do not physically exist in the RAM. All data movement between the host processor and the real-time clock is done through registers mapped to the standard I/O space. The register map is shown in Table 12-6. Table 12-6. RTC I/O Registers Datasheet I/O Locations If U128E bit = 0 70h and 74h Also alias to 72h and 76h Real-Time Clock (Standard RAM) Index Register 71h and 75h Also alias to 73h and 77h Real-Time Clock (Standard RAM) Target Register Function 72h and 76h Extended RAM Index Register (if enabled) 73h and 77h Extended RAM Target Register (if enabled) 421 LPC Interface Bridge Registers (D31:F0) Notes: 1. I/O locations 70h and 71h are the standard legacy location for the real-time clock. The map for this bank is shown in Table 12-7. Locations 72h and 73h are for accessing the extended RAM. The extended RAM bank is also accessed using an indexed scheme. I/O address 72h is used as the address pointer and I/O address 73h is used as the data register. Index addresses above 127h are not valid. If the extended RAM is not needed, it may be disabled. 2. Software must preserve the value of bit 7 at I/O addresses 70h. When writing to this address, software must first read the value, and then write the same value for bit 7 during the sequential address write. Port 70h is not directly readable. The only way to read this register is through Alt Access mode. Although RTC Index bits 6:0 are readable from port 74h, bit 7 will always return 0. If the NMI# enable is not changed during normal operation, software can alternatively read this bit once and then retain the value for all subsequent writes to port 70h. 12.6.2 Indexed Registers The RTC contains two sets of indexed registers that are accessed using the two separate Index and Target registers (70/71h or 72/73h), as shown in Table 12-7. Table 12-7. RTC (Standard) RAM Bank Index 00h Seconds 01h Seconds Alarm 02h Minutes 03h Minutes Alarm 04h Hours 05h Hours Alarm 06h Day of Week 07h Day of Month 08h Month 09h Year 0Ah Register A 0Bh Register B 0Ch Register C 0Dh 0Eh-7Fh 422 Name Register D 114 Bytes of User RAM Datasheet LPC Interface Bridge Registers (D31:F0) 12.6.2.1 RTC_REGA--Register A RTC Index: Default Value: Lockable: 0A Undefined No Attribute: R/W Size: 8 bits Power Well:RTC This register is used for general configuration of the RTC functions. None of the bits are affected by RSMRST# or any other PCH reset signal. Datasheet Bit Description 7 Update In Progress (UIP)--R/W. This bit may be monitored as a status flag. 0 = The update cycle will not start for at least 488 s. The time, calendar, and alarm information in RAM is always available when the UIP bit is 0. 1 = The update is soon to occur or is in progress. 6:4 Division Chain Select (DV[2:0])--R/W. These three bits control the divider chain for the oscillator, and are not affected by RSMRST# or any other reset signal. 010 = Normal Operation 11X = Divider Reset 101 = Bypass 15 stages (test mode only) 100 = Bypass 10 stages (test mode only) 011 = Bypass 5 stages (test mode only) 001 = Invalid 000 = Invalid 3:0 Rate Select (RS[3:0])--R/W. Selects one of 13 taps of the 15 stage divider chain. The selected tap can generate a periodic interrupt if the PIE bit is set in Register B. Otherwise this tap will set the PF flag of Register C. If the periodic interrupt is not to be used, these bits should all be set to 0. RS3 corresponds to bit 3. 0000 = Interrupt never toggles 0001 = 3.90625 ms 0010 = 7.8125 ms 0011 = 122.070 s 0100 = 244.141 s 0101 = 488.281 s 0110 = 976.5625 s 0111 = 1.953125 ms 1000 = 3.90625 ms 1001 = 7.8125 ms 1010 = 15.625 ms 1011 = 31.25 ms 1100 = 62.5 ms 1101 = 125 ms 1110 = 250 ms 1111= 500 ms 423 LPC Interface Bridge Registers (D31:F0) 12.6.2.2 RTC_REGB--Register B (General Configuration) RTC Index: Default Value: Lockable: Bit 7 Attribute: R/W Size: 8 bits Power Well:RTC Description Update Cycle Inhibit (SET)--R/W. Enables/Inhibits the update cycles. This bit is not affected by RSMRST# nor any other reset signal. 0 = Update cycle occurs normally once each second. 1 = A current update cycle will abort and subsequent update cycles will not occur until SET is returned to 0. When set is one, the BIOS may initialize time and calendar bytes safely. Note: 424 0Bh U0U00UUU (U: Undefined) No This bit should be set then cleared early in BIOS POST after each powerup directly after coin-cell battery insertion. 6 Periodic Interrupt Enable (PIE)--R/W. This bit is cleared by RSMRST#, but not on any other reset. 0 = Disable. 1 = Enable. Allows an interrupt to occur with a time base set with the RS bits of register A. 5 Alarm Interrupt Enable (AIE)--R/W. This bit is cleared by RTCRST#, but not on any other reset. 0 = Disable. 1 = Enable. Allows an interrupt to occur when the AF is set by an alarm match from the update cycle. An alarm can occur once a second, one an hour, once a day, or one a month. 4 Update-Ended Interrupt Enable (UIE)--R/W. This bit is cleared by RSMRST#, but not on any other reset. 0 = Disable. 1 = Enable. Allows an interrupt to occur when the update cycle ends. 3 Square Wave Enable (SQWE)--R/W. This bit serves no function in the PCH. It is left in this register bank to provide compatibility with the Motorola 146818B. The PCH has no SQW pin. This bit is cleared by RSMRST#, but not on any other reset. 2 Data Mode (DM)--R/W. This bit specifies either binary or BCD data representation. This bit is not affected by RSMRST# nor any other reset signal. 0 = BCD 1 = Binary 1 Hour Format (HOURFORM)--R/W. This bit indicates the hour byte format. This bit is not affected by RSMRST# nor any other reset signal. 0 = Twelve-hour mode. In twelve-hour mode, the seventh bit represents AM as 0 and PM as one. 1 = Twenty-four hour mode. 0 Daylight Savings Legacy Software Support (DSLSWS)--R/W. Daylight savings functionality is no longer supported. This bit is used to maintain legacy software support and has no associated functionality. If BUC.DSO bit is set, the DSLSWS bit continues to be R/W. Datasheet LPC Interface Bridge Registers (D31:F0) 12.6.2.3 RTC_REGC--Register C (Flag Register) RTC Index: Default Value: Lockable: 0Ch 00U00000 (U: Undefined) No Attribute: RO Size: 8 bits Power Well:RTC Writes to Register C have no effect. Bit 7 Interrupt Request Flag (IRQF)--RO. IRQF = (PF * PIE) + (AF * AIE) + (UF *UFE). This bit also causes the RTC Interrupt to be asserted. This bit is cleared upon RSMRST# or a read of Register C. 6 Periodic Interrupt Flag (PF)--RO. This bit is cleared upon RSMRST# or a read of Register C. 0 = If no taps are specified using the RS bits in Register A, this flag will not be set. 1 = Periodic interrupt Flag will be 1 when the tap specified by the RS bits of register A is 1. 5 Alarm Flag (AF)--RO. 0 = This bit is cleared upon RTCRST# or a read of Register C. 1 = Alarm Flag will be set after all Alarm values match the current time. 4 Update-Ended Flag (UF)--RO. 0 = The bit is cleared upon RSMRST# or a read of Register C. 1 = Set immediately following an update cycle for each second. 3:0 12.6.2.4 Description Reserved. Will always report 0. RTC_REGD--Register D (Flag Register) RTC Index: Default Value: Lockable: Attribute: R/W Size: 8 bits Power Well:RTC Bit Description 7 Valid RAM and Time Bit (VRT)--R/W. 0 = This bit should always be written as a 0 for write cycle, however it will return a 1 for read cycles. 1 = This bit is hardwired to 1 in the RTC power well. 6 5:0 12.7 0Dh 10UUUUUU (U: Undefined) No Reserved. This bit always returns a 0 and should be set to 0 for write cycles. Date Alarm--R/W. These bits store the date of month alarm value. If set to 000000b, then a don't care state is assumed. The host must configure the date alarm for these bits to do anything, yet they can be written at any time. If the date alarm is not enabled, these bits will return 0s to mimic the functionality of the Motorola 146818B. These bits are not affected by any reset assertion. Processor Interface Registers Table 12-8 is the register address map for the processor interface registers. Table 12-8. Processor Interface PCI Register Address Map Offset Datasheet Mnemonic Register Name Default Attribute 61h NMI_SC NMI Status and Control 00h R/W, RO 70h NMI_EN NMI Enable 80h R/W (special) R/W 92h PORT92 F0h COPROC_ERR CF9h RST_CNT Init 00h Coprocessor Error 00h WO Reset Control 00h R/W 425 LPC Interface Bridge Registers (D31:F0) 12.7.1 NMI_SC--NMI Status and Control Register I/O Address: Default Value: Lockable: 61h 00h No Bit 12.7.2 Description 7 SERR# NMI Source Status (SERR#_NMI_STS)--RO. 1 = Bit is set if a PCI agent detected a system error and pulses the PCI SERR# line and if bit 2 (PCI_SERR_EN) is cleared. This interrupt source is enabled by setting bit 2 to 0. To reset the interrupt, set bit 2 to 1 and then set it to 0. When writing to port 61h, this bit must be 0. Note: This bit is set by any of the PCH internal sources of SERR; this includes SERR assertions forwarded from the secondary PCI bus, errors on a PCI Express* port, or other internal functions that generate SERR#. 6 IOCHK# NMI Source Status (IOCHK_NMI_STS)--RO. 1 = Bit is set if an LPC agent (using SERIRQ) asserted IOCHK# and if bit 3 (IOCHK_NMI_EN) is cleared. This interrupt source is enabled by setting bit 3 to 0. To reset the interrupt, set bit 3 to 1 and then set it to 0. When writing to port 61h, this bit must be a 0. 5 Timer Counter 2 OUT Status (TMR2_OUT_STS)--RO. This bit reflects the current state of the 8254 counter 2 output. Counter 2 must be programmed following any PCI reset for this bit to have a determinate value. When writing to port 61h, this bit must be a 0. 4 Refresh Cycle Toggle (REF_TOGGLE)--RO. This signal toggles from either 0 to 1 or 1 to 0 at a rate that is equivalent to when refresh cycles would occur. When writing to port 61h, this bit must be a 0. 3 IOCHK# NMI Enable (IOCHK_NMI_EN)--R/W. 0 = Enabled. 1 = Disabled and cleared. 2 PCI SERR# Enable (PCI_SERR_EN)--R/W. 0 = SERR# NMIs are enabled. 1 = SERR# NMIs are disabled and cleared. 1 Speaker Data Enable (SPKR_DAT_EN)--R/W. 0 = SPKR output is a 0. 1 = SPKR output is equivalent to the Counter 2 OUT signal value. 0 Timer Counter 2 Enable (TIM_CNT2_EN)--R/W. 0 = Disable 1 = Enable NMI_EN--NMI Enable (and Real Time Clock Index) Register I/O Address: Default Value: Lockable: Note: 70h 80h No Attribute: R/W (special) Size: 8 bits Power Well:Core The RTC Index field is write-only for normal operation. This field can only be read in AltAccess Mode. Note, however, that this register is aliased to Port 74h (documented in Table 12-6), and all bits are readable at that address. Bits 7 6:0 426 Attribute: R/W, RO Size: 8 bits Power Well:Core Description NMI Enable (NMI_EN)--R/W (special). 0 = Enable NMI sources. 1 = Disable All NMI sources. Real Time Clock Index Address (RTC_INDX)--R/W (special). This data goes to the RTC to select which register or CMOS RAM address is being accessed. Datasheet LPC Interface Bridge Registers (D31:F0) 12.7.3 PORT92--Init Register I/O Address: Default Value: Lockable: 92h 00h No Bit 7:2 12.7.4 Description Reserved 1 Alternate A20 Gate (ALT_A20_GATE)--R/W. Functionality reserved. A20M# functionality is not supported. 0 INIT_NOW--R/W. When this bit transitions from a 0 to a 1, the PCH will force INIT# active for 16 PCI clocks. COPROC_ERR--Coprocessor Error Register I/O Address: Default Value: Lockable: 12.7.5 F0h 00h No Attribute: WO Size: 8 bits Power Well:Core Bits Description 7:0 Coprocessor Error (COPROC_ERR)--WO. Any value written to this register will cause IGNNE# to go active, if FERR# had generated an internal IRQ13. For FERR# to generate an internal IRQ13, the COPROC_ERR_EN bit must be 1. RST_CNT--Reset Control Register I/O Address: Default Value: Lockable: CF9h 00h No Bit 7:4 3 Attribute: R/W Size: 8 bits Power Well:Core Description Reserved Full Reset (FULL_RST)--R/W. This bit is used to determine the states of SLP_S3#, SLP_S4#, and SLP_S5# after a CF9 hard reset (SYS_RST =1 and RST_CPU is set to 1), after PWROK going low (with RSMRST# high), or after two TCO timeouts. 0 = PCH will keep SLP_S3#, SLP_S4# and SLP_S5# high. 1 = PCH will drive SLP_S3#, SLP_S4# and SLP_S5# low for 3-5 seconds. Note: Datasheet Attribute: R/W Size: 8 bits Power Well:Core When this bit is set, it also causes the full power cycle (SLP_S3/4/5# assertion) in response to SYS_RESET#, PWROK#, and Watchdog timer reset sources. 2 Reset Processor (RST_CPU)--R/W. When this bit transitions from a 0 to a 1, it initiates a hard or soft reset, as determined by the SYS_RST bit (bit 1 of this register). 1 System Reset (SYS_RST)--R/W. This bit is used to determine a hard or soft reset to the processor. 0 = When RST_CPU bit goes from 0 to 1, the PCH performs a soft reset by activating INIT# for 16 PCI clocks. 1 = When RST_CPU bit goes from 0 to 1, the PCH performs a hard reset by activating PLTRST# and SUS_STAT# active for a minimum of about 1 milliseconds. In this case, SLP_S3#, SLP_S4# and SLP_S5# state (assertion or de-assertion) depends on FULL_RST bit setting. The PCH main power well is reset when this bit is 1. It also resets the resume well bits (except for those noted throughout this document). 0 Reserved 427 LPC Interface Bridge Registers (D31:F0) 12.8 Power Management Registers The power management registers are distributed within the PCI Device 31: Function 0 space, as well as a separate I/O range. Each register is described below. Unless otherwise indicated, bits are in the main (core) power well. Bits not explicitly defined in each register are assumed to be reserved. When writing to a reserved bit, the value should always be 0. Software should not attempt to use the value read from a reserved bit, as it may not be consistently 1 or 0. 12.8.1 Power Management PCI Configuration Registers (PM--D31:F0) Table 12-9 shows a small part of the configuration space for PCI Device 31: Function 0. It includes only those registers dedicated for power management. Some of the registers are only used for Legacy Power management schemes. Table 12-9. Power Management PCI Register Address Map (PM--D31:F0) 12.8.1.1 Offset Mnemonic A0h-A1h GEN_PMCON_1 A2-A3h Default Attribute General Power Management Configuration 1 0000h R/W, R/WLO, RO GEN_PMCON_2 General Power Management Configuration 2 2000h R/W, R/WC, RO A4h-A5h GEN_PMCON_3 General Power Management Configuration 3 4206h R/W, R/WC, RO, R/WL A6h GEN_PMCON_LOCK General Power Management Configuration Lock 00h RO, R/WL AAh BM_BREAK_EN_2 BM_BREAK_EN Register #2 00h R/W, RO ABh BM_BREAK_EN BM_BREAK_EN Register 00h R/W, RO Power Management Initialization 00000000h R/W, R/WLO GPI Routing Control Register 00000000h R/W GPI Routing Control Register #2 00000000h R/W ACh-AFh PMIR B8h-BBh GPI_ROUT BCh-BFh GPI_ROUT2 Register Name GEN_PMCON_1--General PM Configuration 1 Register (PM--D31:F0) Offset Address: A0-A1h Default Value: 0000h Lockable: No Bit 428 Attribute: R/W, RO, R/WLO Size: 16 bits Usage: ACPI, Legacy Power Well:Core Description 15 Reserved 14 GEN_PMCON_1 Field 4--R/W. BIOS may write to this field. 13 GEN_PMCON_1 Field 3--R/W. BIOS may write to this field. 12 GEN_PMCON_1 Field 2--R/W. BIOS may write to this field. 11 GEN_PMCON_1 Field 1--R/W. BIOS must program this field to 1b. 10 BIOS_PCI_EXP_EN--R/W. This bit acts as a global enable for the SCI associated with the PCI Express* ports. 0 = The various PCI Express ports and processor cannot cause the PCI_EXP_STS bit to go active. 1 = The various PCI Express ports and processor can cause the PCI_EXP_STS bit to go active. Datasheet LPC Interface Bridge Registers (D31:F0) Bit 9 8:7 Description PWRBTN_LVL--RO. This bit indicates the current state of the PWRBTN# signal. 0 = Low. 1 = High. Reserved 6 SMI_LOCK_GP22--R/WLO. When this bit is set, writes to GPI_ROUT2[7:6], ALT_GPI_SMI_EN2[3], and GP_IO_SEL[22] will have no effect. Once the SMI_LOCK_GP22 bit is set, writes of 0 to SMI_LOCK_GP22 have no effect (that is, once set, this bit can only be cleared by PLTRST#). 5 SMI_LOCK_GP6--R/WLO. When this bit is set, writes to GPI_ROUT[13:12], ALT_GPI_SMI_EN[6] and GP_IO_SEL[6] will have no effect. Once the SMI_LOCK_GP6 bit is set, writes of 0 to SMI_LOCK_GP6 have no effect (that is, once set, this bit can only be cleared by PLTRST#). 4 SMI_LOCK--R/WLO. When this bit is set, writes to the GLB_SMI_EN bit (PMBASE + 30h, bit 0) will have no effect. Once the SMI_LOCK bit is set, writes of 0 to SMI_LOCK bit will have no effect (that is, once set, this bit can only be cleared by PLTRST#). 3 (Mobile Only) 3 (Desktop Only) Reserved Pseudo CLKRUN_EN (PSEUDO_CLKRUN_EN)--R/W. 0 = Disable. 1 = Enable internal CLKRUN# logic to allow DMI PLL shutdown. This bit has no impact on state of external CLKRUN# pin. Notes: 1. PSEUDO_CLKRUN_EN bit does not result in STP_PCI# assertion to actually stop the external PCICLK. 2. This bit should be set mutually exclusive with the CLKRUN_EN bit. Setting PSEUDO_CLKRUN_EN in a mobile SKU could result in unspecified behavior. 2 (Mobile Only) PCI CLKRUN# Enable (CLKRUN_EN)--R/W. 0 = Disable. PCH drives the CLKRUN# signal low. 1 = Enable CLKRUN# logic to control the system PCI clock using the CLKRUN# and STP_PCI# signals. Notes: 1. When the SLP_EN# bit is set, the PCH drives the CLKRUN# signal low regardless of the state of the CLKRUN_EN bit. This ensures that the PCI and LPC clocks continue running during a transition to a sleep state. 2. This bit should be set mutually exclusive with the PSEUDO_CLKRUN_EN bit. Setting CLKRUN_EN in a non-mobile SKU could result in unspecified behavior. 2 (Desktop Only) 1:0 Datasheet Reserved Periodic SMI# Rate Select (PER_SMI_SEL)--R/W. Set by software to control the rate at which periodic SMI# is generated. 00 = 64 seconds 01 = 32 seconds 10 = 16 seconds 11 = 8 seconds 429 LPC Interface Bridge Registers (D31:F0) 12.8.1.2 GEN_PMCON_2--General PM Configuration 2 Register (PM--D31:F0) Offset Address: A2-A3h Default Value: 2000h Lockable: No Bit Attribute: R/W, RO, R/WC Size: 16 bits Usage: ACPI, Legacy Power Well:RTC, SUS Description 15 Reserved 14 DC_PP_DIS--R/W. On DC PHY Power Diable. * When this bit is set, SLP_LAN# will be driven low when ACPRESENT is low. This indicates that LAN PHY should be powered off on battery mode. * When this bit is cleared (default), ACPRESENT state does not impact SLP_LAN# value. Refer to Section 5.14.10.5 for more details on SLP_LAN# value. This bit is reset by RTCRST#. 13 DSX_PP_DIS--/W. In Deep Sx PHY Power Disable. * When this bit is set (default), SLP_LAN# will be driven low in Deep Sx. * When cleared, SLP_LAN# status in Deep Sx is dependant on status of Sx_PP_EN setting. Refer to Section 5.14.10.5 for more details on SLP_LAN# value. This bit is reset by RTCRST#. 12 AG3_PP_EN--R/W. After G3 PHY Power Enable. * When this bit is cleared (default), SLP_LAN# will be driven low upon exiting G3. * When this bit is set, SLP_LAN# value is dependant on DSX_PP_DIS and Sx_PP_EN setting. Refer to Section 5.14.10.5 for more details on SLP_LAN# value. This bit is reset by RTCRST#. 11 Sx_PP_EN--R/W. Sx PHY Power Enable (Non G3 to Sx entry) * When this bit is cleared (default), SLP_LAN# will be driven low in Sx/M-Off. * When this bit is set, SLP_LAN# will be driven high in Sx/M-Off. Refer to Section 5.14.10.5 for more details on SLP_LAN# value. This bit is on VCCDSW3_3 and is reset when DSW is reset. 10:8 7 Reserved DRAM Initialization Bit--R/W. This bit does not affect hardware functionality in any way. BIOS is expected to set this bit prior to starting the DRAM initialization sequence and to clear this bit after completing the DRAM initialization sequence. BIOS can detect that a DRAM initialization sequence was interrupted by a reset by reading this bit during the boot sequence. * If the bit is 1, then the DRAM initialization was interrupted. * This bit is reset by the assertion of the RSMRST# pin. 6 Reserved 5 Memory Placed in Self-Refresh (MEM_SR)--RO. * If the bit is 1, DRAM should have remained powered and held in Self-Refresh through the last power state transition (that is, the last time the system left S0). * This bit is reset by the assertion of the RSMRST# pin. 4 System Reset Status (SRS)--R/WC. Software clears this bit by writing a 1 to it. 0 = SYS_RESET# button Not pressed. 1 = PCH sets this bit when the SYS_RESET# button is pressed. BIOS is expected to read this bit and clear it, if it is set. Notes: 1. This bit is also reset by RSMRST# and CF9h resets. 2. The SYS_RESET# is implemented in the Main power well. This pin must be properly isolated and masked to prevent incorrectly setting this Suspend well status bit. 430 Datasheet LPC Interface Bridge Registers (D31:F0) Bit Description 3 Processor Thermal Trip Status (CTS)--R/WC. 0 = Software clears this bit by writing a 1 to it. 1 = This bit is set when PLTRST# is inactive and THRMTRIP# goes active while the system is in an S0 or S1 state. Notes: 1. This bit is also reset by RSMRST#, and CF9h resets. It is not reset by the shutdown and reboot associated with the processor THRMTRIP# event. 2. The CF9h reset in the description refers to CF9h type core well reset which includes SYS_RESET#, PWROK/SYS_PWROK low, SMBus hard reset, TCO Timeout. This type of reset will clear CTS bit. 2 Minimum SLP_S4# Assertion Width Violation Status--R/WC. 0 = Software clears this bit by writing a 1 to it. 1 = Hardware sets this bit when the SLP_S4# assertion width is less than the time programmed in the SLP_S4# Minimum Assertion Width field (D31:F0:Offset A4h:bits 5:4). The PCH begins the timer when SLP_S4# is asserted during S4/S5 entry or when the RSMRST# input is deasserted during SUS well power-up. This bit is functional regardless of the values in the SLP_S4# Assertion Stretch Enable (D31:F0:Offset A4h:bit 3) and in the Disable SLP Stretching after SUS Well Power Up (D31:F0:Offset A4h:bit 12). Note: 12.8.1.3 This bit is reset by the assertion of the RSMRST# pin, but can be set in some cases before the default value is readable. 1 SYS_PWROK Failure (SYSPWR_FLR)--R/WC. 0 = This bit will be cleared only be software writing a 1 back to the bit or by SUS well power loss. 1 = This bit will be set any time SYS_PWROK drops unexpectedly when the system was in S0 or S1 state. 0 PWROK Failure (PWROK_FLR)--R/WC. 0 = This bit will be cleared only be software writing a 1 back to the bit or by SUS well power loss. 1 = This bit will be set any time PWROK goes low when the system was in S0 or S1 state. Note: See Chapter 5.14.10.3 for more details about the PWROK pin functionality. GEN_PMCON_3--General PM Configuration 3 Register (PM--D31:F0) Offset Address: A4-A5h WL Default Value: 4206h Lockable: No Attribute: R/W, R/WC, RO, R/ Size: 16 bits Usage: ACPI, Legacy Power Well:RTC, SUS Bit Description 15 PME B0 S5 Disable (PME_B0_S5_DIS)--R/W. When set to 1, this bit blocks wake events from PME_B0_STS in S5, regardless of the state of PME_B0_EN. When cleared (default), wake events from PME_B0_STS are allowed in S5 if PME_B0_EN = 1. Wakes from power states other than S5 are not affected by this policy bit. The net effect of setting PME_B0_S5_DIS = '1' is described by the truth table below: Y = Wake; N = Don't wake; B0 = PME_B0_EN; OV = WoL Enable Override B0/OV S1/S3/S4 S5 00 N N 01 N Y (LAN only) 11 Y (all PME B0 sources) Y (LAN only) 10 Y (all PME B0 sources) N This bit is cleared by the RTCRST# pin. Datasheet 431 LPC Interface Bridge Registers (D31:F0) Bit Description 14 SUS Well Power Failure (SUS_PWR_FLR)--R/WC. 0 = Software writes a 1 to this bit to clear it. 1 = This bit is set to '1' whenever SUS well power is lost, as indicated by RSMRST# assertion. This bit is in the SUS well, and defaults to '1' based on RSMRST# assertion (not cleared by any type of reset). 13 WoL Enable Override (WOL_EN_OVRD)--R/W. 0 = WoL policies are determined by PMEB0 enable bit and appropriate LAN status bits 1 = Enable appropriately configured integrated LAN to wake the system in S5 only regardless of the value in the PME_B0_EN bit in the GPE0_EN register. This bit is cleared by the RTCRST# pin. 12 Disable SLP Stretching After SUS Well Power Up (DIS_SLP_STRCH_SUS_UP): R/WL 0 = Enables stretching on SLP signals after SUS power failure as enabled and configured in other fields. 1 = Disables stretching on SLP signals when powering up after a SUS well power loss. regardless of the state of the SLP_S4# Assertion Stretch Enable (bit 3). This bit is cleared by the RTCRST# pin. Notes: 1. This field is RO when the SLP Stretching Policy Lock-Down bit is set. 2. If this bit is cleared, SLP stretch timers start on SUS well power up (the PCH has no ability to count stretch time while the SUS well is powered down). 3. This policy bit has a different effect on SLP_SUS# stretching than on the other SLP_* pins since SLP_SUS# is the control signal for one of the scenarios where SUS well power is lost (Deep Sx). The effect of setting this bit to '1' on: -- SLP_S3# and SLP_S4# stretching: disabled after any SUS power loss. -- SLP_SUS# stretching: disabled after G3, but no impact on Deep Sx. 11:10 SLP_S3# Minimum Assertion Width (SLP_S3_MIN_ASST_WDTH): R/WL This 2-bit value indicates the minimum assertion width of the SLP_S3# signal to ensure that the Main power supplies have been fully power-cycled. Valid Settings are: 00 = 60 us 01 = 1 ms 10 = 50 ms 11 = 2 s This bit is cleared by the RSMRST# pin. Note: 9 8 7:6 432 This field is RO when the SLP Stretching Policy Lock-Down bit is set. General Reset Status (GEN_RST_STS)--R/WC. This bit is set by hardware whenever PLTRST# asserts for any reason other than going into a software-entered sleep state (using PM1CNT.SLP_EN write) or a suspend well power failure (RSMRST# pin assertion). BIOS is expected to consult and then write a 1 to clear this bit during the boot flow before determining what action to take based on PM1_STS.WAK_STS = 1. If GEN_RST_STS = 1, the cold reset boot path should be followed rather than the resume path, regardless of the setting of WAK_STS. This bit is cleared by the RSMRST# pin. Reserved. SWSMI_RATE_SEL--R/W. This field indicates when the SWSMI timer will time out. Valid values are: 00 = 1.5 ms 0.6 ms 01 = 16 ms 4 ms 10 = 32 ms 4 ms 11 = 64 ms 4 ms These bits are not cleared by any type of reset except RTCRST#. Datasheet LPC Interface Bridge Registers (D31:F0) Bit Description 5:4 SLP_S4# Minimum Assertion Width(SLP_S4_MIN_ASST_WDTH)--R/WL. This field indicates the minimum assertion width of the SLP_S4# signal to ensure that the DRAM modules have been safely power-cycled. Valid values are: 11 = 1 second 10 = 2 seconds 01 = 3 seconds 00 = 4 seconds This value is used in two ways: 1. If the SLP_S4# assertion width is ever shorter than this time, a status bit is set for BIOS to read when S0 is entered. 2. If enabled by bit 3 in this register, the hardware will prevent the SLP_S4# signal from deasserting within this minimum time period after asserting. RTCRST# forces this field to the conservative default state (00b). Notes: 1. This field is RO when the SLP Stretching Policy Lock-Down bit is set. 2. The logic that measures this time is in the suspend power well. Therefore, when leaving a G3 or Deep Sx state, the minimum time is measured from the de-assertion of the internal suspend well reset (unless the "Disable SLP Stretching After SUS Well Power Up" bit is set). 3 SLP_S4# Assertion Stretch Enable--R/WL. 0 = The SLP_S4# minimum assertion time is defined in Power Sequencing and Reset Signal Timings table. 1 = The SLP_S4# signal minimally assert for the time specified in bits 5:4 of this register. This bit is cleared by RTCRST#. Note: This bit is RO when the SLP Stretching Policy Lock-Down bit is set. 2 RTC Power Status (RTC_PWR_STS)--R/W. This bit is set when RTCRST# indicates a weak or missing battery. The bit is not cleared by any type of reset. The bit will remain set until the software clears it by writing a 0 back to this bit position. 1 Power Failure (PWR_FLR)--R/WC. This bit is in the DeepSx well and defaults to 1 based on DPWROK de-assertion (not cleared by any type of reset). 0 = Indicates that the trickle current has not failed since the last time the bit was cleared. Software clears this bit by writing a 1 to it. 1 = Indicates that the trickle current (from the main battery or trickle supply) was removed or failed. Note: 0 Note: Datasheet Clearing CMOS in a PCH-based platform can be done by using a jumper on RTCRST# or GPI. Implementations should not attempt to clear CMOS by using a jumper to pull VccRTC low. AFTERG3_EN--R/W. This bit determines what state to go to when power is re-applied after a power failure (G3 state). This bit is in the RTC well and is only cleared by RTCRST# assertion. 0 = System will return to S0 state (boot) after power is re-applied. 1 = System will return to the S5 state (except if it was in S4, in which case it will return to S4). In the S5 state, the only enabled wake event is the Power Button or any enabled wake event that was preserved through the power failure. RSMRST# is sampled using the RTC clock. Therefore, low times that are less than one RTC clock period may not be detected by the PCH. 433 LPC Interface Bridge Registers (D31:F0) 12.8.1.4 GEN_PMCON_LOCK--General Power Management Configuration Lock Register Offset Address: Default Value: Lockable: Power Well: A6h 00h No Core Bit 7:3 12.8.1.5 RO, R/WLO 8 bits ACPI Description Reserved 2 SLP Stretching Policy Lock-Down (SLP_STR_POL_LOCK)--R/WLO. When set to 1, this bit locks down the Disable SLP Stretching After SUS Well Power Up, SLP_S3# Minimum Assertion Width, SLP_S4# Minimum Assertion Width, SLP_S4# Assertion Stretch Enable bits in the GEN_PMCON_3 register, making them read-only. This bit becomes locked when a value of 1b is written to it. Writes of 0 to this bit are always ignored. This bit is cleared by platform reset. 1 ACPI_BASE_LOCK--R/WLO. When set to 1, this bit locks down the ACPI Base Address Register (ABASE) at offset 40h. The Base Address Field becomes read-only. This bit becomes locked when a value of 1b is written to it. Writes of 0 to this bit are always ignored. Once locked by writing 1, the only way to clear this bit is to perform a platform reset. 0 Reserved BM_BREAK_EN_2 Register #2 (PM--D31:F0) Offset Address: Default Value: Lockable: Power Well: Bit 7:2 434 Attribute: Size: Usage: AAh 00h No Core Attribute: Size: Usage: R/W, RO 8 bits ACPI, Legacy Description Reserved 1 xHCI Break Enable (xHCI_BREAK_EN)--R/W. 0 = xHCI traffic will not cause BM_STS to be set. 1 = xHCI traffic will cause BM_STS to be set. 0 SATA3 Break Enable (SATA3_BREAK_EN)--R/W. 0 = SATA3 traffic will not cause BM_STS to be set. 1 = SATA3 traffic will cause BM_STS to be set. Datasheet LPC Interface Bridge Registers (D31:F0) 12.8.1.6 BM_BREAK_EN Register (PM--D31:F0) Offset Address: Default Value: Lockable: Power Well: Bit Attribute: Size: Usage: Storage Break Enable (STORAGE_BREAK_EN)--R/W. 0 = Serial ATA traffic will not cause BM_STS to be set. 1 = Serial ATA traffic will cause BM_STS to be set. 6 PCIE_BREAK_EN--R/W. 0 = PCI Express* traffic will not cause BM_STS to be set. 1 = PCI Express traffic will cause BM_STS to be set. 2 R/W, RO 8 bits ACPI, Legacy Description 7 5:3 Datasheet ABh 00h No Core Reserved EHCI_BREAK_EN--R/W. 0 = EHCI traffic will not cause BM_STS to be set. 1 = EHCI traffic will cause BM_STS to be set. 1 Reserved 0 HDA_BREAK_EN--R/W. 0 = Intel High Definition Audio traffic will not cause BM_STS to be set. 1 = Intel High Definition Audio traffic will cause BM_STS to be set. 435 LPC Interface Bridge Registers (D31:F0) 12.8.1.7 GPI_ROUT--GPI Routing Control Register (PM--D31:F0) Offset Address: B8h-BBh Default Value: 00000000h Lockable: No Bit 436 Attribute: R/W Size: 32 bits Power Well:Suspend Description 31:30 GPI 15 Route--R/W. See bits 1:0 for description. 29:28 GPI 14 Route--R/W. See bits 1:0 for description. 27:26 GPI 13 Route--R/W. See bits 1:0 for description. 25:24 GPI 12 Route--R/W. See bits 1:0 for description. 23:22 GPI 11 Route--R/W. See bits 1:0 for description. 21:20 GPI 10 Route--R/W. See bits 1:0 for description. 19:18 GPI 9 Route--R/W. See bits 1:0 for description. 17:16 GPI 8 Route--R/W. See bits 1:0 for description. 15:14 GPI 7 Route--R/W. See bits 1:0 for description. 13:12 GPI 6 Route--R/W. See bits 1:0 for description. 11:10 GPI 5 Route--R/W. See bits 1:0 for description. 9:8 GPI 4 Route--R/W. See bits 1:0 for description. 7:6 GPI 3 Route--R/W. See bits 1:0 for description. 5:4 GPI 2 Route--R/W. See bits 1:0 for description. 3:2 GPI 1 Route--R/W. See bits 1:0 for description. 1:0 GPI 0 Route--R/W. If the corresponding GPIO is implemented and is configured as an Input, then a `1' in the corresponding GP_LVL bit can be routed to cause an interrupt. The type of interrupt (that is, NMI, SMI# or SCI) depends on the configuration bits in this register as well as the configuration bits in related registers, as described below. 00 = No effect. 01 = SMI# (if corresponding ALT_GPI_SMI_EN bit is also set). 10 = SCI (if corresponding GPE0_EN bit is also set). 11 = NMI (if corresponding GPI_NMI_EN is also set). If the system is in an S3-S5 state and if the GPE0_EN bit is also set, then the GPIO can cause a Wake event from Sx state, even if the GPIO is NOT routed to cause an NMI, SMI#, or SCI. Exception: If the system is in S5 state due to a power button override, then the GPIs will not cause wake events. Further, Core well GPIs are not capable of waking the system from sleep states where the Core well is not powered. Note: If the GPIO is not set to an input, or if the Native function is selected, then the corresponding field in this register has no effect. Datasheet LPC Interface Bridge Registers (D31:F0) 12.8.1.8 GPI_ROUT2--GPI Routing Control Register #2 (PM-D31:F0) Offset Address: BCh-BFh Default Value: 00000000h Lockable: No Bit 12.8.2 Attribute: R/W Size: 32 bits Power Well:Suspend Description 31:16 Reserved 15:14 GPI60 Route--R/W. See bits 1:0 for description. 13:12 GPI57 Route--R/W. See bits 1:0 for description. 11:10 GPI56 Route--R/W. See bits 1:0 for description. 9:8 GPI43 Route--R/W. See bits 1:0 for description. 7:6 GPI22 Route--R/W. See bits 1:0 for description. 5:4 GPI21 Route--R/W. See bits 1:0 for description. 3:2 GPI19 Route--R/W. See bits 1:0 for description. 1:0 GPI17 Route--R/W. If the corresponding GPIO is implemented and is configured as an Input, then a `1' in the corresponding GP_LVL bit can be routed to cause an interrupt. The type of interrupt (that is, NMI, SMI# or SCI) depends on the configuration bits in this register as well as the configuration bits in related registers, as described below. 00 = No effect. 01 = SMI# (if corresponding ALT_GPI_SMI_EN2 bit is also set). 10 = SCI (if corresponding GPE0_EN bit is also set). 11 = NMI (if corresponding GPI_NMI_EN is also set). If the system is in an S3-S5 state and if the GPE0_EN bit is also set, then the GPIO can cause a Wake event from Sx state, even if the GPIO is NOT routed to cause an NMI, SMI# or SCI. Exception: If the system is in S5 state due to a power button override, then the GPIs will not cause wake events. Further, Core well GPIs are not capable of waking the system from sleep states where the Core well is not powered. Note: If the GPIO is not set to an input, or if the Native function is selected, then the corresponding field in this register has no effect. APM I/O Decode Register Table 12-10 shows the I/O registers associated with APM support. This register space is enabled in the PCI Device 31: Function 0 space (APMDEC_EN), and cannot be moved (fixed I/O location). Table 12-10. APM Register Map 12.8.2.1 Address Mnemonic B2h APM_CNT B3h APM_STS Default Type Advanced Power Management Control Port 00h R/W Advanced Power Management Status Port 00h R/W APM_CNT--Advanced Power Management Control Port Register I/O Address: Default Value: Lockable: Power Well: Bit 7:0 Datasheet Register Name B2h 00h No Core Attribute: Size: Usage: R/W 8 bits Legacy Only Description Used to pass an APM command between the OS and the SMI handler. Writes to this port not only store data in the APMC register, but also generates an SMI# when the APMC_EN bit is set. 437 LPC Interface Bridge Registers (D31:F0) 12.8.2.2 APM_STS--Advanced Power Management Status Port Register I/O Address: Default Value: Lockable: Power Well: 12.8.3 B3h 00h No Core Attribute: Size: Usage: R/W 8 bits Legacy Only Bit Description 7:0 Used to pass data between the OS and the SMI handler. Basically, this is a scratchpad register and is not affected by any other register or function (other than a PCI reset). Power Management I/O Registers Table 12-11 shows the registers associated with ACPI and Legacy power management support. These registers locations are all offsets from the ACPI base address defined in the PCI Device 31: Function 0 space (PMBASE), and can be moved to any 128-byte aligned I/O location. In order to access these registers, the ACPI Enable bit (ACPI_EN) must be set. The registers are defined to support the ACPI 4.0a specification and generally use the same bit names. Note: All reserved bits and registers will always return 0 when read, and will have no effect when written. Table 12-11. ACPI and Legacy I/O Register Map 438 PMBASE + Offset Mnemonic 00h-01h PM1_STS 02h-03h PM1_EN 04h-07h PM1_CNT PM1 Control 08h-0Bh PM1_TMR PM1 Timer 20h-27h GPE0_STS General Purpose Event 0 Status 28h-2Fh GPE0_EN 30h-33h Register Name Default Attribute PM1 Status 0000h R/WC PM1 Enable 0000h R/W 00000000h R/W, WO 00000000h RO 000000000000 0000h RO, R/WC General Purpose Event 0 Enables 00000000 00000000h RO, R/W SMI_EN SMI# Control and Enable 00000002h R/W, WO, R/WO 34h-37h SMI_STS SMI Status 00000000h R/WC, RO 38h-39h ALT_GPI_SMI_EN Alternate GPI SMI Enable 0000h R/W 3Ah-3Bh ALT_GPI_SMI_STS Alternate GPI SMI Status 0000h R/WC 42h GPE_CNTL 44h-45h DEVACT_STS General Purpose Event Control Device Activity Status PM2 Control 00h R/W 0000h R/WC 50h PM2_CNT 00h R/W 5Ch-5Dh ALT_GPI_SMI_EN2 Alternate GPI SMI Enable 2 Register 0000h R/W, RO 5Eh-5Fh ALT_GPI_SMI_STS2 Alternate GPI SMI Status 2 Register 0000h RO, RWC 60h-7Fh -- -- -- Reserved for TCO Datasheet LPC Interface Bridge Registers (D31:F0) 12.8.3.1 PM1_STS--Power Management 1 Status Register I/O Address: Default Value: Lockable: Power Well: PMBASE + 00h 0000h No Bits 0-7: Core, Bits 12-15: Suspend Bit 11: RTC, Bits 8, 10 and 14: DSW Attribute: Size: Usage: R/WC 16 bits ACPI or Legacy If bit 10 or 8 in this register is set, and the corresponding _EN bit is set in the PM1_EN register, then the PCH will generate a Wake Event. Once back in an S0 state (or if already in an S0 state when the event occurs), the PCH will also generate an SCI if the SCI_EN bit is set, or an SMI# if the SCI_EN bit is not set. Note: Bit 5 does not cause an SMI# or a wake event. Bit 0 does not cause a wake event but can cause an SMI# or SCI. Bit Description 15 Wake Status (WAK_STS)--R/WC. This bit is not affected by hard resets caused by a CF9 write, but is reset by RSMRST#. 0 = Software clears this bit by writing a 1 to it. 1 = Set by hardware when the system is in one of the sleep states (using the SLP_EN bit) and an enabled wake event occurs. Upon setting this bit, the PCH will transition the system to the ON state. If the AFTERG3_EN bit is not set and a power failure (such as removed batteries) occurs without the SLP_EN bit set, the system will return to an S0 state when power returns, and the WAK_STS bit will not be set. If the AFTERG3_EN bit is set and a power failure occurs without the SLP_EN bit having been set, the system will go into an S5 state when power returns, and a subsequent wake event will cause the WAK_STS bit to be set. Any subsequent wake event would have to be caused by either a Power Button press, or an enabled wake event that was preserved through the power failure (enable bit in the RTC well). 14 PCI Express* Wake Status (PCIEXPWAK_STS)--R/WC. 0 = Software clears this bit by writing a 1 to it. If the WAKE# pin is still active during the write or the PME message received indication has not been cleared in the root port, then the bit will remain active (that is, all inputs to this bit are level-sensitive). 1 = This bit is set by hardware to indicate that the system woke due to a PCI Express wakeup event. This wakeup event can be caused by the PCI Express WAKE# pin being active or receipt of a PCI Express PME message at a root port. This bit is set only when one of these events causes the system to transition from a non-S0 system power state to the S0 system power state. This bit is set independent of the state of the PCIEXP_WAKE_DIS bit. Note: 13:12 Reserved 11 Power Button Override Status (PWRBTNOR_STS)--R/WC. 0 = Software clears this bit by writing a 1 to it. 1 = This bit is set any time a Power Button Override occurs (that is, the power button is pressed for at least 4 consecutive seconds), due to the corresponding bit in the SMBus slave message, Intel ME Initiated Power Button Override, Intel ME Initiated Host Reset with Power down or due to an internal thermal sensor catastrophic condition. The power button override causes an unconditional transition to the S5 state. The BIOS or SCI handler clears this bit by writing a 1 to it. This bit is not affected by hard resets using CF9h writes, and is not reset by RSMRST#. Thus, this bit is preserved through power failures. If this bit is still asserted when the global SCI_EN is set, an SCI will be generated. 10 RTC Status (RTC_STS)--R/WC. This bit is not affected by hard resets caused by a CF9 write, but is reset by DPWROK. 0 = Software clears this bit by writing a 1 to it. 1 = Set by hardware when the RTC generates an alarm (assertion of the IRQ8# signal). Additionally if the RTC_EN bit (PMBASE + 02h, bit 10) is set, the setting of the RTC_STS bit will generate a wake event. 9 Datasheet This bit does not itself cause a wake event or prevent entry to a sleeping state. Thus, if the bit is 1 and the system is put into a sleeping state, the system will not automatically wake. Reserved 439 LPC Interface Bridge Registers (D31:F0) Bit Description 8 Power Button Status (PWRBTN__STS)--R/WC. This bit is not affected by hard resets caused by a CF9 write but is reset by DPWROK. 0 = If the PWRBTN# signal is held low for more than 4 seconds, the hardware clears the PWRBTN_STS bit, sets the PWRBTNOR_STS bit, and the system transitions to the S5 state with only PWRBTN# enabled as a wake event. This bit can be cleared by software by writing a one to the bit position. 1 = This bit is set by hardware when the PWRBTN# signal is asserted Low, independent of any other enable bit. In the S0 state, while PWRBTN_EN and PWRBTN_STS are both set, an SCI (or SMI# if SCI_EN is not set) will be generated. In any sleeping state S1-S5, while PWRBTN_EN (PMBASE + 02h, bit 8) and PWRBTN_STS are both set, a wake event is generated. Note: 7:6 Reserved 5 Global Status (GBL _STS)--R/WC. 0 = The SCI handler should then clear this bit by writing a 1 to the bit location. 1 = Set when an SCI is generated due to BIOS wanting the attention of the SCI handler. BIOS has a corresponding bit, BIOS_RLS, which will cause an SCI and set this bit. 4 Bus Master Status (BM_STS)--R/WC. This bit will not cause a wake event, SCI or SMI#. 0 = Software clears this bit by writing a 1 to it. 1 = Set by the PCH when a PCH-visible bus master requests access to memory or the BMBUSY# signal is active. 3:1 0 12.8.3.2 If the PWRBTN_STS bit is cleared by software while the PWRBTN# signal is sell asserted, this will not cause the PWRBN_STS bit to be set. The PWRBTN# signal must go inactive and active again to set the PWRBTN_STS bit. Reserved Timer Overflow Status (TMROF_STS)--R/WC. 0 = The SCI or SMI# handler clears this bit by writing a 1 to the bit location. 1 = This bit gets set any time bit 22 of the 24-bit timer goes high (bits are numbered from 0 to 23). This will occur every 2.3435 seconds. When the TMROF_EN bit (PMBASE + 02h, bit 0) is set, then the setting of the TMROF_STS bit will additionally generate an SCI or SMI# (depending on the SCI_EN). PM1_EN--Power Management 1 Enable Register I/O Address: Default Value: Lockable: Power Well: Bit Attribute: Size: Usage: R/W 16 bits ACPI or Legacy Description 15 Reserved 14 PCI Express* Wake Disable(PCIEXPWAK_DIS)--R/W. Modification of this bit has no impact on the value of the PCIEXP_WAKE_STS bit. 0 = Inputs to the PCIEXP_WAKE_STS bit in the PM1 Status register enabled to wake the system. 1 = Inputs to the PCIEXP_WAKE_STS bit in the PM1 Status register disabled from waking the system. 13:11 10 9 440 PMBASE + 02h 0000h No Bits 0-7: Core, Bits 8-9, 11-13, 15: Suspend, Bit 14: DSW, Bit 10: RTC Reserved RTC Event Enable (RTC_EN)--R/W. This bit is in the RTC well to allow an RTC event to wake after a power failure. 0 = No SCI (or SMI#) or wake event is generated then RTC_STS (PMBASE + 00h, bit 10) goes active. 1 = An SCI (or SMI#) or wake event will occur when this bit is set and the RTC_STS bit goes active. Reserved Datasheet LPC Interface Bridge Registers (D31:F0) Bit Description 8 Power Button Enable (PWRBTN_EN)--R/W. This bit is used to enable the setting of the PWRBTN_STS bit to generate a power management event (SMI#, SCI). PWRBTN_EN has no effect on the PWRBTN_STS bit (PMBASE + 00h, bit 8) being set by the assertion of the power button. The Power Button is always enabled as a Wake event. 0 = Disable. 1 = Enable. 7:6 5 Global Enable (GBL_EN)--R/W. When both the GBL_EN and the GBL_STS bit (PMBASE + 00h, bit 5) are set, an SCI is raised. 0 = Disable. 1 = Enable SCI on GBL_STS going active. 4:1 0 12.8.3.3 Reserved Reserved Timer Overflow Interrupt Enable (TMROF_EN)--R/W. Works in conjunction with the SCI_EN bit (PMBASE + 04h, bit 0) as described below: TMROF_EN SCI_EN Effect when TMROF_STS is set 0 X No SMI# or SCI 1 0 SMI# 1 1 SCI PM1_CNT--Power Management 1 Control Register I/O Address: Default Value: Lockable: Power Well: PMBASE + 04h 00000000h No Bits 0-9, 13-31: Core, Bits 10-12: RTC Bit 31:14 13 12:10 9:3 2 Datasheet Attribute: Size: Usage: R/W, WO 32 bits ACPI or Legacy Description Reserved Sleep Enable (SLP_EN)--WO. Setting this bit causes the system to sequence into the Sleep state defined by the SLP_TYP field. Sleep Type (SLP_TYP)--R/W. This 3-bit field defines the type of Sleep the system should enter when the SLP_EN bit is set to 1. These bits are only reset by RTCRST#. Code Master Interrupt 000b ON: Typically maps to S0 state. 001b Puts Processor Core in S1 state. 010b Reserved 011b Reserved 100b Reserved 101b Suspend-To-RAM. Assert SLP_S3#: Typically maps to S3 state. 110b Suspend-To-Disk. Assert SLP_S3#, and SLP_S4#: Typically maps to S4 state. 111b Soft Off. Assert SLP_S3#, SLP_S4#, and SLP_S5#: Typically maps to S5 state. Reserved Global Release (GBL_RLS)--WO. 0 = This bit always reads as 0. 1 = ACPI software writes a 1 to this bit to raise an event to the BIOS. BIOS software has a corresponding enable and status bits to control its ability to receive ACPI events. 441 LPC Interface Bridge Registers (D31:F0) 12.8.3.4 Bit Description 1 Bus Master Reload (BM_RLD)--R/W. This bit is treated as a scratchpad bit. This bit is reset to 0 by PLTRST# 0 = Bus master requests will not cause a break from the C3 state. 1 = Enables Bus Master requests (internal or external) to cause a break from the C3 state. If software fails to set this bit before going to C3 state, the PCH will still return to a snoopable state from C3 or C4 states due to bus master activity. 0 SCI Enable (SCI_EN)--R/W. Selects the SCI interrupt or the SMI# interrupt for various events including the bits in the PM1_STS register (bit 10, 8, 0), and bits in GPE0_STS. 0 = These events will generate an SMI#. 1 = These events will generate an SCI. PM1_TMR--Power Management 1 Timer Register I/O Address: Default Value: Lockable: Power Well: PMBASE + 08h 00000000h No Core Bit 31:24 23:0 12.8.3.5 Attribute: Size: Usage: RO 32 bits ACPI Description Reserved Timer Value (TMR_VAL)--RO. Returns the running count of the PM timer. This counter runs off a 3.579545 MHz clock (14.31818 MHz divided by 4). It is reset to 0 during a PCI reset, and then continues counting as long as the system is in the S0 state. After an S1 state, the counter will not be reset (it will continue counting from the last value in S0 state. Anytime bit 22 of the timer goes HIGH to LOW (bits referenced from 0 to 23), the TMROF_STS bit (PMBASE + 00h, bit 0) is set. The High-to-Low transition will occur every 2.3435 seconds. If the TMROF_EN bit (PMBASE + 02h, bit 0) is set, an SCI interrupt is also generated. GPE0_STS--General Purpose Event 0 Status Register I/O Address: RO Default Value: Lockable: Power Well: PMBASE + 20h Attribute: 0000000000000000h Size: No Usage: Bits 0-34, 36-37, 56-63: Suspend, Bit 35, 38: DSW Bits 0:32,35 R/WC Bits 33:34, 36:63 64-bit ACPI This register is symmetrical to the General Purpose Event 0 Enable Register. Unless indicated otherwise below, if the corresponding _EN bit is set, then when the _STS bit is set, the PCH will generate a Wake Event. Once back in an S0 state (or if already in an S0 state when the event occurs), the PCH will also generate an SCI if the SCI_EN bit is set, or an SMI# if the SCI_EN bit (PMBASE + 04h, bit 0) is not set. Bits 31:16 are reset by a CF9h full reset; bits 63:32 and 15:0 are not reset. All bits (except bit 35) are reset by RSMRST#. Bit 35 is reset by DPWROK. Bit 442 Description 63 GPI60_STS - R/WC. Refer to bit[56] in this register for description. 62 GPI57_STS - R/WC. Refer to bit[56] in this register for description. 61 GPI56_STS - R/WC. Refer to bit[56] in this register for description. 60 GPI43_STS - R/WC. Refer to bit[56] in this register for description. 59 GPI22_STS - R/WC. Refer to bit[56] in this register for description. 58 GPI21_STS - R/WC. Refer to bit[56] in this register for description. Datasheet LPC Interface Bridge Registers (D31:F0) Bit Description 57 GPI19_STS - R/WC. Refer to bit[56] in this register for description. 56 GPI17_STS--R/WC. 0 = Software clears this bit by writing a 1 to it. 1 = These bits are set any time the corresponding GPIO is set up as an input and the corresponding GPIO signal is high (or low if the corresponding GP_INV bit is set). If the corresponding enable bit is set in the GPE0_EN register, then when the GPI[n]_STS bit is set: * If the system is in an S1-S5 state, the event will also wake the system. * If the system is in an S0 state (or upon waking back to an S0 state), a SCI will be caused depending on the GPI_ROUT2 bits (D31:F0:BCh, bits 15:0) for the corresponding GPI. 55-39 38 37:36 35 Reserved Wake Alarm Device Timer Status (WADT_STS)--R/WC. This bit is set whenever any of the wake alarm device timers signal a timer expiration. Reserved GPI27_STS--R/WC. 0 = Disable. 1 = Set by hardware and can be reset by writing a one to this bit position or a resume well reset. This bit is set whenever GPIO27 is seen asserted low. GPIO27 is always monitored as an input for the purpose of setting this bit, regardless of the actual GPIO configuration. Note: GPI27 can be configured as wake input to allow wakes from Deep Sx but, since the pin is shared, the PCH counts on this pin remaining asserted until PLTRST# de-asserts or the PCH may misinterpret the pin assertion as a LAN wake request. 34:32 Reserved 31:16 GPIn_STS--R/WC. 0 = Software clears this bit by writing a 1 to it. 1 = These bits are set any time the corresponding GPIO is set up as an input and the corresponding GPIO signal is high (or low if the corresponding GP_INV bit is set). If the corresponding enable bit is set in the GPE0_EN register, then when the GPI[n]_STS bit is set: * If the system is in an S1-S5 state, the event will also wake the system. * If the system is in an S0 state (or upon waking back to an S0 state), a SCI will be caused depending on the GPI_ROUT bits (D31:F0:B8h, bits 31:30) for the corresponding GPI. Note: 15:14 13 Datasheet Mapping is as follows: bit 31 corresponds to GPI[15]... and bit 16 corresponds to GPI[0]. Reserved PME_B0_STS--R/WC. This bit will be set to 1 by the PCH when any internal device with PCI Power Management capabilities on bus 0 asserts the equivalent of the PME# signal. Additionally, if the PME_B0_EN bit and SCI_EN bits are set, and the system is in an S0 state, then the setting of the PME_B0_STS bit will generate an SCI (or SMI# if SCI_EN is not set). If the PME_B0_EN bit is set, and the system is in an S1-S4 state (or S5 state due to SLP_TYP and SLP_EN), then the setting of the PME_B0_STS bit will generate a wake event. If the system is in an S5 state due to power button override, then the PME_B0_STS bit will not cause a wake event or SCI. The default for this bit is 0. Writing a 1 to this bit position clears this bit. The following are internal devices which can set this bit: * Intel HD Audio * Intel Management Engine "maskable" wake events * Integrated LAN * SATA * EHCI * XHCI 12 Reserved 11 PME_STS--R/WC. 0 = Software clears this bit by writing a 1 to it. 1 = Set by hardware when the PME# signal goes active. Additionally, if the PME_EN and SCI_EN bits are set, and the system is in an S0 state, then the setting of the PME_STS bit will generate an SCI or SMI# (if SCI_EN is not set). If the PME_EN bit is set, and the system is in an S1-S4 state (or S5 state due to setting SLP_TYP and SLP_EN), then the setting of the PME_STS bit will generate a wake event. If the system is in an S5 state due to power button override or a power failure, then PME_STS will not cause a wake event or SCI. 443 LPC Interface Bridge Registers (D31:F0) Bit 10 (Desktop Only) 10 (Mobile Only) Reserved BATLOW_STS--R/WC. (Mobile Only) Software clears this bit by writing a 1 to it. 0 = BATLOW# Not asserted 1 = Set by hardware when the BATLOW# signal is asserted. 9 PCI_EXP_STS--R/WC. 0 = Software clears this bit by writing a 1 to it. 1 = Set by hardware to indicate that: -- The PME event message was received on one or more of the PCI Express* ports -- An Assert PMEGPE message received from the processor using DMI Notes: 1. The PCI WAKE# pin has no impact on this bit. 2. If the PCI_EXP_STS bit went active due to an Assert PMEGPE message, then a Deassert PMEGPE message must be received prior to the software write in order for the bit to be cleared. 3. If the bit is not cleared and the corresponding PCI_EXP_EN bit is set, the level-triggered SCI will remain active. 4. A race condition exists where the PCI Express device sends another PME message because the PCI Express device was not serviced within the time when it must resend the message. This may result in a spurious interrupt, and this is comprehended and approved by the PCI Express* Specification, Revision 1.0a. The window for this race condition is approximately 95-105 milliseconds. 8 RI_STS--R/WC. 0 = Software clears this bit by writing a 1 to it. 1 = Set by hardware when the RI# input signal goes active. 7 SMBus Wake Status (SMB_WAK_STS)--R/WC. Software clears this bit by writing a 1 to it. 0 = Wake event not caused by the PCH's SMBus logic. 1 = Set by hardware to indicate that the wake event was caused by the PCH's SMBus logic. The SMI handler should then clear this bit. NOTES: 1. The SMBus controller will independently cause an SMI# so this bit does not need to do so (unlike the other bits in this register). 2. This bit is set by the SMBus slave command 01h (Wake/SMI#) even when the system is in the S0 state. Therefore, to avoid an instant wake on subsequent transitions to sleep states, software must clear this bit after each reception of the Wake/SMI# command or just prior to entering the sleep state. 3. The SMBALERT_STS bit (SMB_BASE+00h:Bit 5) should be cleared by software before the SMB_WAK_STS bit is cleared. 6 TCOSCI_STS--R/WC. Software clears this bit by writing a 1 to it. 0 = TOC logic or thermal sensor logic did Not cause SCI. 1 = Set by hardware when the TCO logic or thermal sensor logic causes an SCI. 5:3 444 Description Reserved 2 SWGPE_STS--R/WC. The SWGPE_CTRL bit (bit 1 of GPE_CTRL reg) acts as a level input to this bit. 1 HOT_PLUG_STS--R/WC. 0 = This bit is cleared by writing a 1 to this bit position. 1 = When a PCI Express* Hot-Plug event occurs. This will cause an SCI if the HOT_PLUG_EN and SCI_EN bits are set. 0 Reserved Datasheet LPC Interface Bridge Registers (D31:F0) 12.8.3.6 GPE0_EN--General Purpose Event 0 Enables Register I/O Address: Default Value: Lockable: Power Well: PMBASE + 28h Attribute: 0000000000000000h Size: No Usage: Bits 0-7, 9, 12, 14-34, 36-63 Suspend, Bits 8, 10-11, 13, 35 RTC R/W 64-bit ACPI This register is symmetrical to the General Purpose Event 0 Status Register. Bit Description 63 GPI[60]_EN - R/W. Refer to bit 56 for description. 62 GPI[57]_EN - R/W. Refer to bit 56 for description. 61 GPI[56]_EN - R/W. Refer to bit 56 for description. 60 GPI[43]_EN - R/W. Refer to bit 56 for description. 59 GPI[22]_EN - R/W. Refer to bit 56 for description. 58 GPI[21]_EN - R/W. Refer to bit 56 for description. 57 GPI[19]_EN - R/W. Refer to bit 56 for description. 56 GPI[17]_EN - R/W. This bit enables the corresponding GPI[n]_STS bits being set to cause an SCI and/or wake event. 55:39 38 37-36 35 Reserved WADT_EN - R/W. Used to enable the setting of the WADT_STS bit to generate wake/SMI#/SCI. Reserved GPI27_EN--R/W. 0 = Disable. 1 = Enable the setting of the GPI27_STS bit to generate a wake event/SCI/SMI#. GPIO27 is a valid host wake event from Deep Sx. The wake enable configuration persists after a G3 state. Note: Host wake events from the PHY through GPIO27 cannot be disabled by clearing this bit. Note: In the Deep S4/S5 state, GPIO27 has no GPIO functionality other than wake enable capability if this corresponding bit is set. Note: GPI27 can be configured as wake input to allow wakes from Deep Sx but, since the pin is shared, the PCH counts on this pin remaining asserted until PLTRST# de-asserts or the PCH may misinterpret the pin assertion as a LAN wake request. 34:32 Reserved 31:16 GPIn_EN--R/W. These bits enable the corresponding GPI[n]_STS bits being set to cause a SCI, and/or wake event. These bits are cleared by RSMRST#. Note: Mapping is as follows: bit 31 corresponds to GPI15... and bit 16 corresponds to GPI0. 15:14 Reserved 13 PME_B0_EN--R/W. 0 = Disable Note: 12 Reserved 11 PME_EN--R/W. 0 = Disable. 1 = Enables the setting of the PME_STS to generate a wake event and/or an SCI. PME# can be a wake event from the S1-S4 state or from S5 (if entered using SLP_EN, but not power button override). 10 (Desktop Only) Datasheet Enables the setting of the PME_B0_STS bit to generate a wake event and/or an SCI or SMI#. Reserved 445 LPC Interface Bridge Registers (D31:F0) Bit Description 10 (Mobile Only) BATLOW_EN--R/W. (Mobile Only) 0 = Disable. 1 = Enables the BATLOW# signal to cause an SMI# or SCI (depending on the SCI_EN bit) when it goes low. This bit does not prevent the BATLOW# signal from inhibiting the wake event. 9 PCI_EXP_EN--R/W. 0 = Disable SCI generation upon PCI_EXP_STS bit being set. 1 = Enables PCH to cause an SCI when PCI_EXP_STS bit is set. This is used to allow the PCI Express* ports, including the link to the processor, to cause an SCI due to wake/PME events. 8 RI_EN--R/W. The value of this bit will be maintained through a G3 state and is not affected by a hard reset caused by a CF9h write. 0 = Disable. 1 = Enables the setting of the RI_STS to generate a wake event. 7 Reserved 6 TCOSCI_EN--R/W. 0 = Disable. 1 = Enables the setting of the TCOSCI_STS to generate an SCI. 5:3 12.8.3.7 Reserved 2 SWGPE_EN--R/W. This bit allows software to control the assertion of SWGPE_STS bit. This bit This bit, when set to 1, enables the SW GPE function. If SWGPE_CTRL is written to a 1, hardware will set SWGPE_STS (acts as a level input) If SWGPE_STS, SWGPE_EN, and SCI_EN are all 1s, an SCI will be generated If SWGPE_STS = 1, SWGPE_EN = 1, SCI_EN = 0, and GBL_SMI_EN = 1 then an SMI# will be generated 1 HOT_PLUG_EN--R/W. 0 = Disables SCI generation upon the HOT_PLUG_STS bit being set. 1 = Enables the PCH to cause an SCI when the HOT_PLUG_STS bit is set. This is used to allow the PCI Express* ports to cause an SCI due to Hot-Plug events. 0 Reserved SMI_EN--SMI Control and Enable Register I/O Address: Default Value: Lockable: Power Well: Note: PMBASE + 30h 00000002h No Core R/W, R/WO, WO 32 bit ACPI or Legacy This register is symmetrical to the SMI status register. Bit Description 31 xHCI SMI Enable (xHCI _SMI_EN)--R/W. 0 = Disable 1 = Enables xHCI to generate an SMI# 30 ME SMI Enable (ME _SMI_EN)--R/W. 0 = Disable 1 = Enables ME to generate an SMI# 29:28 27 26:19 18 446 Attribute: Size: Usage: Reserved GPIO_UNLOCK_SMI_EN--R/WO. Setting this bit will cause the PCH to generate an SMI# when the GPIO_UNLOCK_SMI_STS bit is set in the SMI_STS register. Once written to 1, this bit can only be cleared by PLTRST#. Reserved INTEL_USB2_EN--R/W. 0 = Disable 1 = Enables Intel-Specific EHCI SMI logic to cause SMI#. Datasheet LPC Interface Bridge Registers (D31:F0) Bit 17 16:15 Description LEGACY_USB2_EN--R/W. 0 = Disable 1 = Enables legacy EHCI logic to cause SMI#. Reserved 14 PERIODIC_EN--R/W. 0 = Disable. 1 = Enables the PCH to generate an SMI# when the PERIODIC_STS bit (PMBASE + 34h, bit 14) is set in the SMI_STS register (PMBASE + 34h). 13 TCO_EN--R/W. 0 = Disables TCO logic generating an SMI#. If the NMI2SMI_EN bit is set, SMIs that are caused by re-routed NMIs will not be gated by the TCO_EN bit. Even if the TCO_EN bit is 0, NMIs will still be routed to cause SMIs. 1 = Enables the TCO logic to generate SMI#. Note: 12 Reserved 11 MCSMI_EN Microcontroller SMI Enable (MCSMI_EN)--R/W. 0 = Disable. 1 = Enables PCH to trap accesses to the microcontroller range (62h or 66h) and generate an SMI#. The "trapped' cycles will be claimed by the PCH on PCI, but not forwarded to LPC. 10:8 Datasheet This bit cannot be written once the TCO_LOCK bit is set. Reserved 7 BIOS Release (BIOS_RLS)--WO. 0 = This bit will always return 0 on reads. Writes of 0 to this bit have no effect. 1 = Enables the generation of an SCI interrupt for ACPI software when a one is written to this bit position by BIOS software. Note: GBL_STS being set will cause an SCI, even if the SCI_EN bit is not set. Software must take great care not to set the BIOS_RLS bit (which causes GBL_STS to be set) if the SCI handler is not in place. 6 Software SMI# Timer Enable (SWSMI_TMR_EN)--R/W. 0 = Disable. Clearing the SWSMI_TMR_EN bit before the timer expires will reset the timer and the SMI# will not be generated. 1 = Starts Software SMI# Timer. When the SWSMI timer expires (the timeout period depends upon the SWSMI_RATE_SEL bit setting), SWSMI_TMR_STS is set and an SMI# is generated. SWSMI_TMR_EN stays set until cleared by software. 5 APMC_EN--R/W. 0 = Disable. Writes to the APM_CNT register will not cause an SMI#. 1 = Enables writes to the APM_CNT register to cause an SMI#. 4 SLP_SMI_EN--R/W. 0 = Disables the generation of SMI# on SLP_EN. This bit must be 0 before the software attempts to transition the system into a sleep state by writing a 1 to the SLP_EN bit. 1 = A write of 1 to the SLP_EN bit (bit 13 in PM1_CNT register) will generate an SMI#, and the system will not transition to the sleep state based on that write to the SLP_EN bit. 3 LEGACY_USB_EN--R/W. 0 = Disable. 1 = Enables legacy USB circuit to cause SMI#. 2 BIOS_EN--R/W. 0 = Disable. 1 = Enables the generation of SMI# when ACPI software writes a 1 to the GBL_RLS bit (D31:F0:PMBase + 04h:bit 2). If the BIOS_STS bit (D31:F0:PMBase + 34h:bit 2), which gets set when software writes 1 to GBL_RLS bit, is already a 1 at the time that BIOS_EN becomes 1, an SMI# will be generated when BIOS_EN gets set. 447 LPC Interface Bridge Registers (D31:F0) 12.8.3.8 Bit Description 1 End of SMI (EOS)--R/W (special). This bit controls the arbitration of the SMI signal to the processor. This bit must be set for the PCH to assert SMI# low to the processor after SMI# has been asserted previously. 0 = Once the PCH asserts SMI# low, the EOS bit is automatically cleared. 1 = When this bit is set to 1, SMI# signal will be de-asserted for 4 PCI clocks before its assertion. In the SMI handler, the processor should clear all pending SMIs (by servicing them and then clearing their respective status bits), set the EOS bit, and exit SMM. This will allow the SMI arbiter to re-assert SMI upon detection of an SMI event and the setting of a SMI status bit. Note: The PCH is able to generate 1st SMI after reset even though EOS bit is not set. Subsequent SMI require EOS bit is set. 0 GBL_SMI_EN--R/W. 0 = No SMI# will be generated by PCH. This bit is reset by a PCI reset event. 1 = Enables the generation of SMI# in the system upon any enabled SMI event. Note: When the SMI_LOCK bit is set, this bit cannot be changed. SMI_STS--SMI Status Register I/O Address: Default Value: Lockable: Power Well: Note: Attribute: Size: Usage: RO, R/WC 32 bits ACPI or Legacy If the corresponding _EN bit is set when the _STS bit is set, the PCH will cause an SMI# (except bits 8-10 and 12, which do not need enable bits since they are logic ORs of other registers that have enable bits). The PCH uses the same GPE0_EN register (I/O address: PMBase+2Ch) to enable/disable both SMI and ACPI SCI general purpose input events. ACPI OS assumes that it owns the entire GPE0_EN register per the ACPI specification. Problems arise when some of the general-purpose inputs are enabled as SMI by BIOS, and some of the general purpose inputs are enabled for SCI. In this case ACPI OS turns off the enabled bit for any GPIx input signals that are not indicated as SCI general-purpose events at boot, and exit from sleeping states. BIOS should define a dummy control method which prevents the ACPI OS from clearing the SMI GPE0_EN bits. Bit 31:28 Description Reserved 27 GPIO_UNLOCK_SMI_STS--R/WC. This bit will be set if the GPIO registers lockdown logic is requesting an SMI#. Writing a 1 to this bit position clears this bit to 0. 26 SPI_STS--RO. This bit will be set if the SPI logic is generating an SMI#. This bit is read only because the sticky status and enable bits associated with this function are located in the SPI registers. 25:22 448 PMBASE + 34h 00000000h No Core Reserved 21 MONITOR_STS--RO. This bit will be set if the Trap/SMI logic has caused the SMI. This will occur when the processor or a bus master accesses an assigned register (or a sequence of accesses). See Section 10.1.17 through Section 10.1.33 for details on the specific cause of the SMI. 20 PCI_EXP_SMI_STS--RO. PCI Express* SMI event occurred. This could be due to a PCI Express* PME event or Hot-Plug event. 19 Reserved 18 INTEL_USB2_STS--RO. This non-sticky read-only bit is a logical OR of each of the SMI status bits in the Intel-Specific EHCI SMI Status Register ANDed with the corresponding enable bits. This bit will not be active if the enable bits are not set. Writes to this bit will have no effect. All integrated EHCIs are represented with this bit. 17 LEGACY_USB2_STS--RO. This non-sticky read-only bit is a logical OR of each of the SMI status bits in the EHCI Legacy Support Register ANDed with the corresponding enable bits. This bit will not be active if the enable bits are not set. Writes to this bit will have no effect. All integrated ECHIs are represented with this bit. Datasheet LPC Interface Bridge Registers (D31:F0) Bit Datasheet Description 16 SMBus SMI Status (SMBUS_SMI_STS)--R/WC. Software clears this bit by writing a 1 to it. 0 = This bit is set from the 64 kHz clock domain used by the SMBus. Software must wait at least 15.63 s after the initial assertion of this bit before clearing it. 1 = Indicates that the SMI# was caused by: 1. The SMBus Slave receiving a message that an SMI# should be caused, or 2. The SMBALERT# signal goes active and the SMB_SMI_EN bit is set and the SMBALERT_DIS bit is cleared, or 3. The SMBus Slave receiving a Host Notify message and the HOST_NOTIFY_INTREN and the SMB_SMI_EN bits are set, or 4. The PCH detecting the SMLINK_SLAVE_SMI command while in the S0 state. 15 SERIRQ_SMI_STS--RO. 0 = SMI# was not caused by the SERIRQ decoder. 1 = Indicates that the SMI# was caused by the SERIRQ decoder. Note: This is not a sticky bit 14 PERIODIC_STS--R/WC. Software clears this bit by writing a 1 to it. 0 = Software clears this bit by writing a 1 to it. 1 = This bit is set at the rate determined by the PER_SMI_SEL bits. If the PERIODIC_EN bit (PMBASE + 30h, bit 14) is also set, the PCH generates an SMI#. 13 TCO_STS--R/WC. Software clears this bit by writing a 1 to it. 0 = SMI# not caused by TCO logic. 1 = Indicates the SMI# was caused by the TCO logic. This is not a wake event. 12 Device Monitor Status (DEVMON_STS)--RO. 0 = SMI# not caused by Device Monitor. 1 = Set if bit 0 of the DEVACT_STS register (PMBASE + 44h) is set. The bit is not sticky, so writes to this bit will have no effect. 11 Microcontroller SMI# Status (MCSMI_STS)--R/WC. Software clears this bit by writing a 1 to it. 0 = Indicates that there has been no access to the power management microcontroller range (62h or 66h). 1 = Set if there has been an access to the power management microcontroller range (62h or 66h) and the Microcontroller Decode Enable #1 bit in the LPC Bridge I/O Enables configuration register is 1 (D31:F0:Offset 82h:bit 11). This implementation assumes that the Microcontroller is on LPC. If this bit is set, and the MCSMI_EN bit is also set, the PCH will generate an SMI#. 10 GPE1_STS--RO. This bit is a logical OR of the bits in the ALT_GPI_SMI_STS and the ALT_GPI_SMI_STS2 registers that are also set up to cause an SMI# (as indicated by the GPI_ROUT and GPI_ROUT2 registers) and have the corresponding bit set in the ALT_GPI_SMI_EN and ALT_GPI_SMI_EN2 registers. Bits that are not routed to cause an SMI# will have no effect on this bit. 0 = SMI# was not generated by a GPI assertion. 1 = SMI# was generated by a GPI assertion. 9 GPE0_STS--RO. This bit is a logical OR of the bits 35, 13, 11, 10, 8 and 2 in the GPE0_STS register (PMBASE + 28h) that also have the corresponding bit set in the GPE0_EN register (PMBASE + 2Ch). 0 = SMI# was not generated by a GPE0 event. 1 = SMI# was generated by a GPE0 event. 8 PM1_STS_REG--RO. This is an ORs of the bits in the ACPI PM1 Status Register (offset PMBASE+00h) that can cause an SMI#. 0 = SMI# was not generated by a PM1_STS event. 1 = SMI# was generated by a PM1_STS event. 7 Reserved 6 SWSMI_TMR_STS--R/WC. Software clears this bit by writing a 1 to it. 0 = Software SMI# Timer has Not expired. 1 = Set by the hardware when the Software SMI# Timer expires. 5 APM_STS--R/WC. Software clears this bit by writing a 1 to it. 0 = No SMI# generated by write access to APM Control register with APMCH_EN bit set. 1 = SMI# was generated by a write access to the APM Control register with the APMC_EN bit set. 4 SLP_SMI_STS--R/WC. Software clears this bit by writing a 1 to the bit location. 0 = No SMI# caused by write of 1 to SLP_EN bit when SLP_SMI_EN bit is also set. 1 = Indicates an SMI# was caused by a write of 1 to SLP_EN bit when SLP_SMI_EN bit is also set. 449 LPC Interface Bridge Registers (D31:F0) Bit 3 LEGACY_USB_STS--RO. This bit is a logical OR of each of the SMI status bits in the USB Legacy Keyboard/Mouse Control Registers ANDed with the corresponding enable bits. This bit will not be active if the enable bits are not set. 0 = SMI# was not generated by USB Legacy event. 1 = SMI# was generated by USB Legacy event. 2 BIOS_STS--R/WC. 0 = No SMI# generated due to ACPI software requesting attention. 1 = This bit gets set by hardware when a 1 is written by software to the GBL_RLS bit (D31:F0:PMBase + 04h:bit 2). When both the BIOS_EN bit (D31:F0:PMBase + 30h:bit 2) and the BIOS_STS bit are set, an SMI# will be generated. The BIOS_STS bit is cleared when software writes a 1 to its bit position. 1:0 12.8.3.9 Description Reserved ALT_GPI_SMI_EN--Alternate GPI SMI Enable Register I/O Address: Default Value: Lockable: Power Well: 15:0 Alternate GPI SMI Enable--R/W. These bits are used to enable the corresponding GPIO to cause an SMI#. For these bits to have any effect, the following must be true. * The corresponding bit in the ALT_GPI_SMI_EN register is set. * The corresponding GPI must be routed in the GPI_ROUT register to cause an SMI. * The corresponding GPIO must be implemented. Mapping is as follows: bit 15 corresponds to GPI15... bit 0 corresponds to GPI0. ALT_GPI_SMI_STS--Alternate GPI SMI Status Register PMBASE +3Ah 0000h No Suspend Bit 15:0 Attribute: Size: Usage: R/WC 16 bits ACPI or Legacy Description Alternate GPI SMI Status--R/WC. These bits report the status of the corresponding GPIOs. 0 = Inactive. Software clears this bit by writing a 1 to it. 1 = Active These bits are sticky. If the following conditions are true, then an SMI# will be generated and the GPE0_STS bit set: * The corresponding bit in the ALT_GPI_SMI_EN register (PMBASE + 38h) is set * The corresponding GPIO must be routed in the GPI_ROUT register to cause an SMI. * The corresponding GPIO must be implemented. Note: Note: All bits are in the resume well. Default for these bits is dependent on the state of the GPIO pins. Mapping is as follows: bit 15 corresponds to GPIO15... bit 0 corresponds to GPIO0. GPE_CNTL--General Purpose Control Register I/O Address: Default Value: Lockable: Power Well: 450 R/W 16 bits ACPI or Legacy Description I/O Address: Default Value: Lockable: Power Well: 12.8.3.11 Attribute: Size: Usage: Bit Note: 12.8.3.10 PMBASE +38h 0000h No Suspend PMBASE +42h 00h No Bits 0-1, 3-7: Suspend Bit 2: RTC Attribute: Size: Usage: R/W 8 bits ACPI or Legacy Datasheet LPC Interface Bridge Registers (D31:F0) Bit 7:2 12.8.3.12 Description Reserved 1 SWGPE_CTRL--R/W. This bit allows software to control the assertion of SWGPE_STS bit. This bit is used by hardware as the level input signal for the SWGPE_STS bit in the GPE0_STS register. When SWGPE_CTRL is 1, SWGPE_STS will be set to 1, and writes to SWGPE_STS with a value of 1 to clear SWGPE_STS will result in SWGPE_STS being set back to 1 by hardware. When SWGPE_CTRL is 0, writes to SWGPE_STS with a value of 1 will clear SWGPE_STS to 0. In addition to being cleared by RSMRST# assertion, the PCH also clears this bit due to a Power Button Override event, Intel ME Initiated Power Button Override, Intel ME Initiated Host Reset with Power down, SMBus unconditional power down, processor thermal trip event, or due to an internal thermal sensor catastrophic condition. 0 Reserved DEVACT_STS--Device Activity Status Register I/O Address: Default Value: Lockable: Power Well: PMBASE +44h 0000h No Core Attribute: Size: Usage: R/WC 16 bits Legacy Only Each bit indicates if an access has occurred to the corresponding device's trap range, or for bits 6:9 if the corresponding PCI interrupt is active. This register is used in conjunction with the Periodic SMI# timer to detect any system activity for legacy power management. The periodic SMI# timer indicates if it is the right time to read the DEVACT_STS register (PMBASE + 44h). Note: Software clears bits that are set in this register by writing a 1 to the bit position. Bit 15:13 12 11:10 Reserved KBC_ACT_STS--R/WC. KBC (60/64h). 0 = Indicates that there has been no access to this device I/O range. 1 = This device I/O range has been accessed. Clear this bit by writing a 1 to the bit location. Reserved 9 PIRQDH_ACT_STS--R/WC. PIRQ[D or H]. 0 = The corresponding PCI interrupts have not been active. 1 = At least one of the corresponding PCI interrupts has been active. Clear this bit by writing a 1 to the bit location. 8 PIRQCG_ACT_STS--R/WC. PIRQ[C or G]. 0 = The corresponding PCI interrupts have not been active. 1 = At least one of the corresponding PCI interrupts has been active. Clear this bit by writing a 1 to the bit location. 7 PIRQBF_ACT_STS--R/WC. PIRQ[B or F]. 0 = The corresponding PCI interrupts have not been active. 1 = At least one of the corresponding PCI interrupts has been active. Clear this bit by writing a 1 to the bit location. 6 PIRQAE_ACT_STS--R/WC. PIRQ[A or E]. 0 = The corresponding PCI interrupts have not been active. 1 = At least one of the corresponding PCI interrupts has been active. Clear this bit by writing a 1 to the bit location. 5:0 Datasheet Description Reserved 451 LPC Interface Bridge Registers (D31:F0) 12.8.3.13 PM2_CNT--Power Management 2 Control Register I/O Address: Default Value: Lockable: Power Well: PMBASE + 50h 00h No Core Bit 7:1 0 12.8.3.14 Reserved Arbiter Disable (ARB_DIS)--R/W This bit is a scratchpad bit for legacy software compatibility. ALT_GPI_SMI_EN2--Alternate GPI SMI Enable 2 Register PMBASE + 5Ch 0000h No Suspend Bit 15:8 Attribute: Size: Usage: R/W, RO 16 bits ACPI Description Reserved 7 Alternate GPI[60] SMI Enable (ALT_GPI60_SMI_EN)--R/W. Refer to bit [0] in this register for description. 6 Alternate GPI[57] SMI Enable (ALT_GPI57_SMI_EN)--R/W. Refer to bit [0] in this register for description. 5 Alternate GPI[56] SMI Enable (ALT_GPI56_SMI_EN)--R/W. Refer to bit [0] in this register for description. 4 Alternate GPI[43] SMI Enable (ALT_GPI43_SMI_EN)--R/W. Refer to bit [0] in this register for description. 3 Alternate GPI[22] SMI Enable (ALT_GPI22_SMI_EN)--R/W. Refer to bit [0] in this register for description. 2 Alternate GPI[21] SMI Enable (ALT_GPI21_SMI_EN)--R/W. Refer to bit [0] in this register for description. 1 Alternate GPI[19] SMI Enable (ALT_GPI19_SMI_EN)--R/W. Refer to bit [0] in this register for description. 0 Alternate GPI[17] SMI Enable (ALT_GPI17_SMI_EN)--R/W. These bits are used to enable the corresponding GPIO to cause an SMI#. For these bits to have any effect, the following must be true. * The corresponding bit in the ALT_GPI_SMI_STS2 register is set. * The corresponding GPI must be routed in the GPI_ROUT2 register to cause an SMI. * The corresponding GPIO must be implemented. ALT_GPI_SMI_STS2--Alternate GPI SMI Status 2 Register I/O Address: Default Value: Lockable: Power Well: Bit 15:8 452 R/W 8 bits ACPI Description I/O Address: Default Value: Lockable: Power Well: 12.8.3.15 Attribute: Size: Usage: PMBASE + 5E-5Fh 00h No Suspend Attribute: Size: Usage: R/W, RO 16 bits ACPI Description Reserved 7 Alternate GPI[60] SMI Status (ALT_GPI60_SMI_STS) - R/W. Refer to bit[0] in this register for description. 6 Alternate GPI[57] SMI Status (ALT_GPI57_SMI_STS) - R/W. Refer to bit[0] in this register for description. 5 Alternate GPI[56] SMI Status (ALT_GPI56_SMI_STS) - R/W. Refer to bit[0] in this register for description. Datasheet LPC Interface Bridge Registers (D31:F0) Bit 12.9 Description 4 Alternate GPI[43] SMI Status (ALT_GPI43_SMI_STS) - R/W. Refer to bit[0] in this register for description. 3 Alternate GPI[22] SMI Status (ALT_GPI22_SMI_STS) - R/W. Refer to bit[0] in this register for description. 2 Alternate GPI[21] SMI Status (ALT_GPI21_SMI_STS) - R/W. Refer to bit[0] in this register for description. 1 Alternate GPI[19] SMI Status (ALT_GPI19_SMI_STS) - R/W. Refer to bit[0] in this register for description. 0 Alternate GPI[17] SMI Status (ALT_GPI17_SMI_STS) - R/W. These bits report the status of the corresponding GPIOs. 0 = Inactive. Software clears this bit by writing a 1 to it. 1 = Active These bits are sticky. If the following conditions are true, then an SMI# will be generated and the GPE0_STS bit set: * The corresponding bit in the ALT_GPI_SMI_EN2 register (PMBASE + 5Ch) is set * The corresponding GPIO must be routed in the GPI_ROUT2 register to cause an SMI. * The corresponding GPIO must be implemented. System Management TCO Registers The TCO logic is accessed using registers mapped to the PCI configuration space (D31:F0) and the system I/O space. For TCO PCI Configuration registers, see LPC D31:F0 PCI Configuration registers. TCO Register I/O Map The TCO I/O registers reside in a 32-byte range pointed to by a TCOBASE value, which is, PMBASE + 60h in the PCI config space. The following table shows the mapping of the registers within that 32-byte range. Each register is described in the following sections. Table 12-12. TCO I/O Register Address Map (Sheet 1 of 2) Datasheet TCOBASE + Offset Mnemonic 00h-01h TCO_RLD 02h TCO_DAT_IN 03h TCO_DAT_OUT Register Name Default Attribute 0000h R/W TCO Data In 00h R/W TCO Data Out 00h R/W TCO Timer Reload and Current Value 04h-05h TCO1_STS TCO1 Status 0000h R/WC, RO 06h-07h TCO2_STS TCO2 Status 0000h R/WC 08h-09h TCO1_CNT TCO1 Control 0000h R/W, R/WLO, R/WC 0Ah-0Bh TCO2_CNT TCO2 Control 0008h R/W 0Ch-0Dh TCO_MESSAGE1, TCO_MESSAGE2 TCO Message 1 and 2 00h R/W 0Eh TCO_WDCNT TCO Watchdog Control 00h R/W 0Fh -- 10h SW_IRQ_GEN 11h -- 12h-13h TCO_TMR Reserved Software IRQ Generation Reserved TCO Timer Initial Value -- -- 03h R/W -- -- 0004h R/W 453 LPC Interface Bridge Registers (D31:F0) Table 12-12. TCO I/O Register Address Map (Sheet 2 of 2) 12.9.1 TCOBASE + Offset Mnemonic 14h-1Fh -- Register Name Reserved TCOBASE +00h 0000h No Bit 15:10 9:0 Attribute: R/W Size: 16 bits Power Well:Core TCO Timer Value--R/W. Reading this register will return the current count of the TCO timer. Writing any value to this register will reload the timer to prevent the timeout. TCO_DAT_IN--TCO Data In Register TCOBASE +02h 00h No Attribute: R/W Size: 8 bits Power Well:Core Bit Description 7:0 TCO Data In Value--R/W. This data register field is used for passing commands from the OS to the SMI handler. Writes to this register will cause an SMI and set the SW_TCO_SMI bit in the TCO1_STS register (D31:F0:04h). TCO_DAT_OUT--TCO Data Out Register TCOBASE +03h 00h No Attribute: R/W Size: 8 bits Power Well:Core Bit Description 7:0 TCO Data Out Value--R/W. This data register field is used for passing commands from the SMI handler to the OS. Writes to this register will set the TCO_INT_STS bit in the TCO1_STS register. It will also cause an interrupt, as selected by the TCO_INT_SEL bits. TCO1_STS--TCO1 Status Register I/O Address: Default Value: Lockable: TCOBASE +04h 2000h No Attribute: R/WC, RO Size: 16 bits Power Well:Core (Except bit 7, in RTC) Bit 15:14 454 -- Reserved I/O Address: Default Value: Lockable: 12.9.4 -- Description I/O Address: Default Value: Lockable: 12.9.3 Attribute TCO_RLD--TCO Timer Reload and Current Value Register I/O Address: Default Value: Lockable: 12.9.2 Default Description Reserved 13 TCO_SLVSEL (TCO Slave Select)--RO. This register bit is Read Only by Host and indicates the value of TCO Slave Select Soft Strap. Refer to the PCH Soft Straps section of the SPI Chapter for details. 12 DMISERR_STS--R/WC. 0 = Software clears this bit by writing a 1 to it. 1 = PCH received a DMI special cycle message using DMI indicating that it wants to cause an SERR#. The software must read the processor to determine the reason for the SERR#. Datasheet LPC Interface Bridge Registers (D31:F0) Bit Description 11 Reserved 10 DMISMI_STS--R/WC. 0 = Software clears this bit by writing a 1 to it. 1 = PCH received a DMI special cycle message using DMI indicating that it wants to cause an SMI. The software must read the processor to determine the reason for the SMI. 9 DMISCI_STS--R/WC. 0 = Software clears this bit by writing a 1 to it. 1 = PCH received a DMI special cycle message using DMI indicating that it wants to cause an SCI. The software must read the processor to determine the reason for the SCI. 8 BIOSWR_STS--R/WC. 0 = Software clears this bit by writing a 1 to it. 1 = PCH sets this bit and generates and SMI# to indicate an invalid attempt to write to the BIOS. This occurs when either: a) The BIOSWP bit is changed from 0 to 1 and the BLD bit is also set, or b) any write is attempted to the BIOS and the BIOSWP bit is also set. Note: On write cycles attempted to the 4 MB lower alias to the BIOS space, the BIOSWR_STS will not be set. 7 NEWCENTURY_STS--R/WC. This bit is in the RTC well. 0 = Cleared by writing a 1 to the bit position or by RTCRST# going active. 1 = This bit is set when the Year byte (RTC I/O space, index offset 09h) rolls over from 99 to 00. Setting this bit will cause an SMI# (but not a wake event). Note: The NEWCENTURY_STS bit is not valid when the RTC battery is first installed (or when RTC power has not been maintained). Software can determine if RTC power has not been maintained by checking the RTC_PWR_STS bit (D31:F0:A4h, bit 2), or by other means (such as a checksum on RTC RAM). If RTC power is determined to have not been maintained, BIOS should set the time to a valid value and then clear the NEWCENTURY_STS bit. The NEWCENTURY_STS bit may take up to 3 RTC clocks for the bit to be cleared after a 1 is written to the bit to clear it. After writing a 1 to this bit, software should not exit the SMI handler until verifying that the bit has actually been cleared. This will ensure that the SMI is not re-entered. 6:4 12.9.5 Reserved 3 TIMEOUT--R/WC. 0 = Software clears this bit by writing a 1 to it. 1 = Set by PCH to indicate that the SMI was caused by the TCO timer reaching 0. 2 TCO_INT_STS--R/WC. 0 = Software clears this bit by writing a 1 to it. 1 = SMI handler caused the interrupt by writing to the TCO_DAT_OUT register (TCOBASE + 03h). 1 SW_TCO_SMI--R/WC. 0 = Software clears this bit by writing a 1 to it. 1 = Software caused an SMI# by writing to the TCO_DAT_IN register (TCOBASE + 02h). 0 NMI2SMI_STS--RO. 0 = Cleared by clearing the associated NMI status bit. 1 = Set by the PCH when an SMI# occurs because an event occurred that would otherwise have caused an NMI (because NMI2SMI_EN is set). TCO2_STS--TCO2 Status Register I/O Address: Default Value: Lockable: TCOBASE +06h 0000h No Attribute: R/WC Size: 16 bits Power Well:Resume (Except Bit 0, in RTC) Bit 15:5 Datasheet Description Reserved 455 LPC Interface Bridge Registers (D31:F0) 12.9.6 Bit Description 4 SMLink Slave SMI Status (SMLINK_SLV_SMI_STS)--R/WC. Allow the software to go directly into a pre-determined sleep state. This avoids race conditions. Software clears this bit by writing a 1 to it. 0 = The bit is reset by RSMRST#, but not due to the PCI Reset associated with exit from S3-S5 states. 1 = PCH sets this bit to 1 when it receives the SMI message on the SMLink Slave Interface. 3 Reserved 2 BOOT_STS--R/WC. 0 = Cleared by PCH based on RSMRST# or by software writing a 1 to this bit. Software should first clear the SECOND_TO_STS bit before writing a 1 to clear the BOOT_STS bit. 1 = Set to 1 when the SECOND_TO_STS bit goes from 0 to 1 and the processor has not fetched the first instruction. If rebooting due to a second TCO timer timeout, and if the BOOT_STS bit is set, the PCH will reboot using the `safe' multiplier (1111). This allows the system to recover from a processor frequency multiplier that is too high, and allows the BIOS to check the BOOT_STS bit at boot. If the bit is set and the frequency multiplier is 1111, then the BIOS knows that the processor has been programmed to an invalid multiplier. 1 SECOND_TO_STS--R/WC. 0 = Software clears this bit by writing a 1 to it, or by a RSMRST#. 1 = PCH sets this bit to 1 to indicate that the TIMEOUT bit had been (or is currently) set and a second timeout occurred before the TCO_RLD register was written. If this bit is set and the NO_REBOOT config bit is 0, then the PCH will reboot the system after the second timeout. The reboot is done by asserting PLTRST#. 0 Intruder Detect (INTRD_DET)--R/WC. 0 = Software clears this bit by writing a 1 to it, or by RTCRST# assertion. 1 = Set by PCH to indicate that an intrusion was detected. This bit is set even if the system is in G3 state. Notes: 1. This bit has a recovery time. After writing a 1 to this bit position (to clear it), the bit may be read back as a 1 for up 65 microseconds before it is read as a 0. Software must be aware of this recovery time when reading this bit after clearing it. 2. If the INTRUDER# signal is active when the software attempts to clear the INTRD_DET bit, the bit will remain as a 1, and the SMI# will be generated again immediately. The SMI handler can clear the INTRD_SEL bits (TCOBASE + 0Ah, bits 2:1), to avoid further SMIs. However, if the INTRUDER# signals goes inactive and then active again, there will not be further SMI's (because the INTRD_SEL bits would select that no SMI# be generated). 3. If the INTRUDER# signal goes inactive some point after the INTRD_DET bit is written as a 1, then the INTRD_DET signal will go to a 0 when INTRUDER# input signal goes inactive. This is slightly different than a classic sticky bit, since most sticky bits would remain active indefinitely when the signal goes active and would immediately go inactive when a 1 is written to the bit. TCO1_CNT--TCO1 Control Register I/O Address: Default Value: Lockable: Bit 15:13 456 TCOBASE +08h 0000h No Attribute: R/W, R/WLO, R/WC Size: 16 bits Power Well:Core Description Reserved 12 TCO_LOCK--R/WLO. When set to 1, this bit prevents writes from changing the TCO_EN bit (in offset 30h of Power Management I/O space). Once this bit is set to 1, it can not be cleared by software writing a 0 to this bit location. A core-well reset is required to change this bit from 1 to 0. This bit defaults to 0. 11 TCO Timer Halt (TCO_TMR_HLT)--R/W. 0 = The TCO Timer is enabled to count. 1 = The TCO Timer will halt. It will not count, and thus cannot reach a value that will cause an SMI# or set the SECOND_TO_STS bit. When set, this bit will prevent rebooting and prevent Alert On LAN event messages from being transmitted on the SMLink (but not Alert On LAN* heartbeat messages). 10 Reserved Datasheet LPC Interface Bridge Registers (D31:F0) Bit 9 8 7:0 12.9.7 Description NMI2SMI_EN--R/W. 0 = Normal NMI functionality. 1 = Forces all NMIs to instead cause SMIs. The functionality of this bit is dependent upon the settings of the NMI_EN bit and the GBL_SMI_EN bit as detailed in the following table: NMI_EN GBL_SMI_EN 0b 0b No SMI# at all because GBL_SMI_EN = 0 0b 1b SMI# will be caused due to NMI events 1b 0b No SMI# at all because GBL_SMI_EN = 0 1b 1b No SMI# due to NMI because NMI_EN = 1 NMI_NOW--R/WC. 0 = Software clears this bit by writing a 1 to it. The NMI handler is expected to clear this bit. Another NMI will not be generated until the bit is cleared. 1 = Writing a 1 to this bit causes an NMI. This allows the BIOS or SMI handler to force an entry to the NMI handler. Reserved TCO2_CNT--TCO2 Control Register I/O Address: Default Value: Lockable: Bit 15:6 TCOBASE +0Ah 0008h No Attribute: R/W Size: 16 bits Power Well:Resume Description Reserved 5:4 OS_POLICY--R/W. OS-based software writes to these bits to select the policy that the BIOS will use after the platform resets due the WDT. The following convention is recommended for the BIOS and OS: 00 = Boot normally 01 = Shut down 10 = Do not load OS. Hold in pre-boot state and use LAN to determine next step 11 = Reserved Note: These are just scratchpad bits. They should not be reset when the TCO logic resets the platform due to Watchdog Timer. 3 GPIO11_ALERT_DISABLE--R/W. At reset (using RSMRST# asserted) this bit is set and GPIO[11] alerts are disabled. 0 = Enable. 1 = Disable GPIO11/SMBALERT# as an alert source for the heartbeats and the SMBus slave. 2:1 0 Datasheet Description INTRD_SEL--R/W. This field selects the action to take if the INTRUDER# signal goes active. 00 = No interrupt or SMI# 01 = Interrupt (as selected by TCO_INT_SEL). 10 = SMI 11 = Reserved Reserved 457 LPC Interface Bridge Registers (D31:F0) 12.9.8 TCO_MESSAGE1 and TCO_MESSAGE2 Registers I/O Address: Default Value: Lockable: TCOBASE +0Ch (Message 1) TCOBASE +0Dh (Message 2) 00h No Bit 7:0 12.9.9 TCO_WDCNT--TCO Watchdog Control Register 7:0 Attribute: Size: R/W 8 bits Description The BIOS or system management software can write into this register to indicate more details on the boot progress. The register will reset to 00h based on a RSMRST# (but not PLTRST#). The external microcontroller can read this register to monitor boot progress. SW_IRQ_GEN--Software IRQ Generation Register Offset Address: TCOBASE + 10h Default Value: 03h Power Well: Core Bit 7:2 Attribute: Size: R/W 8 bits Description Reserved 1 IRQ12_CAUSE--R/W. When software sets this bit to 1, IRQ12 will be asserted. When software sets this bit to 0, IRQ12 will be de-asserted. 0 IRQ1_CAUSE--R/W. When software sets this bit to 1, IRQ1 will be asserted. When software sets this bit to 0, IRQ1 will be de-asserted. TCO_TMR--TCO Timer Initial Value Register I/O Address: Default Value: Lockable: Bit 15:10 9:0 458 Size: 8 bits Power Well:Resume TCO_MESSAGE[n]--R/W. BIOS can write into these registers to indicate its boot progress. The external microcontroller can read these registers to monitor the boot progress. Bit 12.9.11 R/W Description Offset Address: TCOBASE + 0Eh Default Value: 00h Power Well: Resume 12.9.10 Attribute: TCOBASE +12h 0004h No Attribute: R/W Size: 16 bits Power Well:Core Description Reserved TCO Timer Initial Value--R/W. Value that is loaded into the timer each time the TCO_RLD register is written. Values of 0000h or 0001h will be ignored and should not be attempted. The timer is clocked at approximately 0.6 seconds, and thus allows timeouts ranging from 1.2 second to 613.8 seconds. Note: The timer has an error of 1 tick (0.6 S). The TCO Timer will only count down in the S0 state. Datasheet LPC Interface Bridge Registers (D31:F0) 12.10 General Purpose I/O Registers The control for the general purpose I/O signals is handled through a 128-byte I/O space. The base offset for this space is selected by the GPIOBASE register. Table 12-13. Registers to Control GPIO Address Map Datasheet GPIOBASE + Offset Mnemonic 00h-03h GPIO_USE_SEL 04h-07h GP_IO_SEL 08h-0Bh -- 0Ch-0Fh GP_LVL 10h-13h -- 14h-17h -- 18h-1Bh GPO_BLINK Register Name Default Attribute GPIO Use Select B96BA1FFh R/W GPIO Input/Output Select EEFF6EFFh R/W Reserved 0h -- 02FE0100h R/W Reserved 0h -- Reserved 0h -- GPIO Blink Enable 00040000h R/W R/W GPIO Level for Input or Output 1Ch-1Fh GP_SER_BLINK GP Serial Blink 00000000h 20h-23h GP_SB_CMDSTS GP Serial Blink Command Status 00080000h R/W 24h-27h GP_SB_DATA GP Serial Blink Data 00000000h R/W 28h-29h GPI_NMI_EN GPI NMI Enable 0000h R/W 2Ah-2Bh GPI_NMI_STS GPI NMI Status 0000h R/WC 2Ch-2Fh GPI_INV GPIO Signal Invert 00000000h R/W 30h-33h GPIO_USE_SEL2 GPIO Use Select 2 020300FEh (mobile only) / 020300FFh (Desktop only) R/W GPIO Input/Output Select 2 1F57FFF4h R/W GPIO Level for Input or Output 2 A4AA0007h R/W 34h-37h GP_IO_SEL2 38h-3Bh GP_LVL2 3Ch-3Fh -- 40h-43h GPIO_USE_SEL3 44h-47h GP_IO_SEL3 48h-4Bh GP_LVL3 4Ch-5Fh -- 60h-63h GP_RST_SEL1 Reserved 0h -- 00000030h (mobile only)/ 00000130h (desktop only) R/W GPIO Input/Output Select 3 00000FF0h R/W GPIO Level for Input or Output 3 000000C0h R/W GPIO Use Select 3 Reserved GPIO Reset Select 1 -- -- 01000000h R/W 64h-67h GP_RST_SEL2 GPIO Reset Select 2 00000000h R/W 68h-6Bh GP_RST_SEL3 GPIO Reset Select 3 00000000h R/W 6Ch-7Fh -- -- -- Reserved 459 LPC Interface Bridge Registers (D31:F0) 12.10.1 GPIO_USE_SEL--GPIO Use Select Register Offset Address: GPIOBASE + 00h Default Value: B96BA1FFh Lockable: Yes Attribute: R/W Size: 32 bits Power Well:Core for 0:7, 16:23, Resume for 8:15, 24:31 Bit Description 31:0 GPIO_USE_SEL[31:0]--R/W. Each bit in this register enables the corresponding GPIO (if it exists) to be used as a GPIO, rather than for the native function. 0 = Signal used as native function. 1 = Signal used as a GPIO. Notes: 1. The following bits are always 1 because they are always unmultiplexed: 8, 15, 24, 27, and 28. 2. After a full reset (RSMRST#) all multiplexed signals in the resume and core wells are configured as their default function. After only a PLTRST#, the GPIOs in the core well are configured as their default function. 3. When configured to GPIO mode, the multiplexing logic will present the inactive state to native logic that uses the pin as an input. 4. All GPIOs are reset to the default state by CF9h reset except GPIO24. Other resume well GPIOs' reset behavior can be programmed using GP_RST_SEL registers. 5. Bit 29 can be configured to GPIO when SLP_WLAN#/GPIO29 Select soft strap is set to 1 (GPIO usage). 12.10.2 GP_IO_SEL--GPIO Input/Output Select Register Offset Address: GPIOBASE +04h Default Value: EEFF6EFFh Lockable: Yes 12.10.3 Attribute: R/W Size: 32 bits Power Well:Core for 0:7, 16:23, Resume for 8:15, 24:31 Bit Description 31:0 GP_IO_SEL[31:0]--R/W. When configured in native mode (GPIO_USE_SEL[n] is 0), writes to these bits have no effect. The value reported in this register is undefined when programmed as native mode. 0 = Output. The corresponding GPIO signal is an output. 1 = Input. The corresponding GPIO signal is an input. GP_LVL--GPIO Level for Input or Output Register Offset Address: GPIOBASE +0Ch Default Value: 02FE0100h Lockable: Yes Bit 31:0 460 Attribute: R/W Size: 32 bits Power Well:Core for 0:7, 16:23, Resume for 8:15, 24:31 Description GP_LVL[31:0]--R/W. These registers are implemented as dual read/write with dedicated storage each. Write value will be stored in the write register, while read is coming from the read register which will always reflect the value of the pin. If GPIO[n] is programmed to be an output (using the corresponding bit in the GP_IO_SEL register), then the corresponding GP_LVL[n] write register value will drive a high or low value on the output pin. 1 = high, 0 = low. When configured in native mode (GPIO_USE_SEL[n] is 0), writes to these bits are stored but have no effect on the pin value. The value reported in this register is undefined when programmed as native mode. Note: Bit 29 setting will be ignored if Intel ME FW is configuring SLP_WLAN# behavior. When GPIO29/SLP_WLAN# Select soft strap is set to 1 (GPIO usage), bit 29 can be used as regular GP_LVL bit. Datasheet LPC Interface Bridge Registers (D31:F0) 12.10.4 GPO_BLINK--GPO Blink Enable Register Offset Address: GPIOBASE +18h Default Value: 00040000h Lockable: No Bit Description 31:0 GP_BLINK[31:0]--R/W. The setting of this bit has no effect if the corresponding GPIO signal is programmed as an input. 0 = The corresponding GPIO will function normally. 1 = If the corresponding GPIO is programmed as an output, the output signal will blink at a rate of approximately once per second. The high and low times have approximately 0.5 seconds each. The GP_LVL bit is not altered when this bit is set. The value of the corresponding GP_LVL bit remains unchanged during the blink process, and does not effect the blink in any way. The GP_LVL bit is not altered when programmed to blink. It will remain at its previous value. These bits correspond to GPIO in the Resume well. These bits revert to the default value based on RSMRST# or a write to the CF9h register (but not just on PLTRST#). Note: 12.10.5 Attribute: R/W Size: 32 bits Power Well:Core for 0:7, 16:23, Resume for 8:15, 24:31 GPIO18 will blink by default immediately after reset. This signal could be connected to an LED to indicate a failed boot (by programming BIOS to clear GP_BLINK18 after successful POST). GP_SER_BLINK--GP Serial Blink Register Offset Address: GPIOBASE +1Ch Default Value: 00000000h Lockable: No Datasheet Attribute: R/W Size: 32 bits Power Well:Core for 0:7, 16:23, Resume for 8:15, 24:31 Bit Description 31:0 GP_SER_BLINK[31:0]--R/W. The setting of this bit has no effect if the corresponding GPIO is programmed as an input or if the corresponding GPIO has the GPO_BLINK bit set. When set to a 0, the corresponding GPIO will function normally. When using serial blink, this bit should be set to a 1 while the corresponding GP_IO_SEL bit is set to 1. Setting the GP_IO_SEL bit to 0 after the GP_SER_BLINK bit ensures PCH will not drive a 1 on the pin as an output. When this corresponding bit is set to a 1 and the pin is configured to output mode, the serial blink capability is enabled. The PCH will serialize messages through an open-drain buffer configuration. The value of the corresponding GP_LVL bit remains unchanged and does not impact the serial blink capability in any way. Writes to this register have no effect when the corresponding pin is configured in native mode and the read value returned is undefined. 461 LPC Interface Bridge Registers (D31:F0) 12.10.6 GP_SB_CMDSTS--GP Serial Blink Command Status Register Offset Address: GPIOBASE +20h Default Value: 00080000h Lockable: No Bit Description 31:24 Reserved 23:22 Data Length Select (DLS)--R/W. This field determines the number of bytes to serialize on GPIO. 00 = Serialize bits 7:0 of GP_SB_DATA (1 byte) 01 = Serialize bits 15:0 of GP_SB_DATA (2 bytes) 10 = Undefined - Software must not write this value 11 = Serialize bits 31:0 of GP_SB_DATA (4 bytes) Software should not modify the value in this register unless the Busy bit is clear. Writes to this register have no effect when the corresponding pin is configured in native mode and the read value returned is undefined. 21:16 Data Rate Select (DRS)--R/W. This field selects the number of 120ns time intervals to count between Manchester data transitions. The default of 8h results in a 960 ns minimum time between transitions. A value of 0h in this register produces undefined behavior. Software should not modify the value in this register unless the Busy bit is clear. 15:9 8 7:1 0 12.10.7 Attribute: R/W, RO Size: 32 bits Power Well:Core Reserved Busy--RO. This read-only status bit is the hardware indication that a serialization is in progress. Hardware sets this bit to 1 based on the Go bit being set. Hardware clears this bit when the Go bit is cleared by the hardware. Reserved Go--R/W. This bit is set to 1 by software to start the serialization process. Hardware clears the bit after the serialized data is sent. Writes of 0 to this register have no effect. Software should not write this bit to 1 unless the Busy status bit is cleared. GP_SB_DATA--GP Serial Blink Data Register Offset Address: GPIOBASE +24h Default Value: 00000000h Lockable: No Bit 31:0 12.10.8 Attribute: R/W Size: 32 bits Power Well: Core Description GP_SB_DATA[31:0]--R/W. This register contains the data serialized out. The number of bits shifted out are selected through the DLS field in the GP_SB_CMDSTS register. This register should not be modified by software when the Busy bit is set. GPI_NMI_EN--GPI NMI Enable Register Offset Address: GPIOBASE +28h Default Value: 00000h Lockable: No 462 Attribute: R/W Size: 16 bits Power Well:Core for 0:7 Resume for 8:15 Bit Description 15:0 GPI_NMI_EN[15:0]. GPI NMI Enable: This bit only has effect if the corresponding GPIO is used as an input and its GPI_ROUT register is being programmed to NMI functionality. When set to 1, it used to allow active-low and active-high inputs (depends on inversion bit) to cause NMI. Datasheet LPC Interface Bridge Registers (D31:F0) 12.10.9 GPI_NMI_STS--GPI NMI Status Register Offset Address: GPIOBASE +2Ah Default Value: 00000h Lockable: Yes Attribute: R/WC Size: 16 bits Power Well:Core for 0:7 Resume for 8:15 Bit Description 15:0 GPI_NMI_STS[15:0]. GPI NMI Status: GPI_NMI_STS[15:0]. GPI NMI Status: This bit is set if the corresponding GPIO is used as an input, and its GPI_ROUT register is being programmed to NMI functionality and also GPI_NMI_EN bit is set when it detects either: 1) active-high edge when its corresponding GPI_INV is configured with value 0. 2) active-low edge when its corresponding GPI_INV is configured with value 1. Note: Writing value of 1 will clear the bit, while writing value of 0 have no effect. 12.10.10 GPI_INV--GPIO Signal Invert Register Offset Address: GPIOBASE +2Ch Default Value: 00000000h Lockable: No Bit 31:16 15:0 Datasheet Attribute: R/W Size: 32 bits Power Well: Core for 17, 16, 7:0 Description Reserved Input Inversion (GP_INV[n])--R/W. This bit only has effect if the corresponding GPIO is used as an input and used by the GPE logic, where the polarity matters. When set to `1', then the GPI is inverted as it is sent to the GPE logic that is using it. This bit has no effect on the value that is reported in the GP_LVL register. These bits are used to allow both active-low and active-high inputs to cause SMI# or SCI. In the S0 or S1 state, the input signal must be active for at least two PCI clocks to ensure detection by the PCH. In the S3, S4, or S5 states the input signal must be active for at least 2 RTC clocks to ensure detection. The setting of these bits has no effect if the corresponding GPIO is programmed as an output. These bits correspond to GPI that are in the resume well, and will be reset to their default values by RSMRST# or by a write to the CF9h register. 0 = The corresponding GPI_STS bit is set when the PCH detects the state of the input pin to be high. 1 = The corresponding GPI_STS bit is set when the PCH detects the state of the input pin to be low. 463 LPC Interface Bridge Registers (D31:F0) 12.10.11 GPIO_USE_SEL2--GPIO Use Select 2 Register Offset Address: GPIOBASE +30h Default Value: 020300FFh (Desktop) 020300FEh (Mobile) Lockable: Yes Attribute: Size: R/W 32 bits Power Well:Core for 0:7, 16:23, Resume for 8:15, 24:31 This register corresponds to GPIO[63:32]. Bit 0 corresponds to GPIO32 and bit 31 corresponds to GPIO63. Bit Description 31:0 GPIO_USE_SEL2[63:32]--R/W. Each bit in this register enables the corresponding GPIO (if it exists) to be used as a GPIO, rather than for the native function. 0 = Signal used as native function. 1 = Signal used as a GPIO. Notes: 1. The following bits are always 1 because they are always unmultiplexed: 3, 25. The following bit is unmultiplexed in desktop and is also 1: 0. 2. If GPIO[n] does not exist, then, the (n-32) bit in this register will always read as 0 and writes will have no effect. The following bit is also not used in mobile and is always 0 on mobile: 0. 3. After a full reset RSMRST# all multiplexed signals in the resume and core wells are configured as their default function. After only a PLTRST#, the GPIOs in the core well are configured as their default function. 4. When configured to GPIO mode, the multiplexing logic will present the inactive state to native logic that uses the pin as an input. 5. Bit 26 is ignored, functionality is configured by bits 9:8 of FLMAP0 register. 6. For GPIO35, write bit 0 is reserved and should always be written as "1". 7. GPIO47 and GPIO56 are mobile only GPIOs and not available on Desktop 12.10.12 GP_IO_SEL2--GPIO Input/Output Select 2 Register Offset Address: GPIOBASE +34h Default Value: 1F57FFF4h Lockable: Yes Attribute: R/W Power Well:Core for 0:7, 16:23, Resume for 8:15, 24:31 This register corresponds to GPIO[63:32]. Bit 0 corresponds to GPIO32 and bit 31 corresponds to GPIO63. Bit 31:0 464 Description GP_IO_SEL2[63:32]--R/W. 0 = GPIO signal is programmed as an output. 1 = Corresponding GPIO signal (if enabled in the GPIO_USE_SEL2 register) is programmed as an input. Datasheet LPC Interface Bridge Registers (D31:F0) 12.10.13 GP_LVL2--GPIO Level for Input or Output 2 Register Offset Address: GPIOBASE +38h Default Value: A4AA0007h Lockable: Yes Attribute: R/W Size: 32 bits Power Well:Core for 0:7, 16:23, Resume for 8:15, 24:31 This register corresponds to GPIO[63:32]. Bit 0 corresponds to GPIO32 and bit 31 corresponds to GPIO63. Bit Description 31:0 GP_LVL[63:32]--R/W. These registers are implemented as dual read/write with dedicated storage each. Write value will be stored in the write register, while read is coming from the read register which will always reflect the value of the pin. If GPIO[n] is programmed to be an output (using the corresponding bit in the GP_IO_SEL register), then the corresponding GP_LVL[n] write register value will drive a high or low value on the output pin. 1 = high, 0 = low. When configured in native mode (GPIO_USE_SEL[n] is 0), writes to these bits are stored but have no effect to the pin value. The value reported in this register is undefined when programmed as native mode. 12.10.14 GPIO_USE_SEL3--GPIO Use Select 3 Register Offset Address: GPIOBASE +40h Default Value: 00000130h (Desktop) 00000030h (Mobile) Lockable: Yes Attribute: Size: R/W 32 bits Power Well:Core for 0:7, 16:23, Resume for 8:15, 24:31 This register corresponds to GPIO[75:64]. Bit 0 corresponds to GPIO64 and bit 11 corresponds to GPIO75. Bit 31:12 11:0 Datasheet Description Always 0. No corresponding GPIO. GPIO_USE_SEL3[75:64]--R/W. Each bit in this register enables the corresponding GPIO (if it exists) to be used as a GPIO, rather than for the native function. 0 = Signal used as native function. 1 = Signal used as a GPIO. Notes: 1. The following bit is always 1 because it is always unmultiplexed: 8 2. If GPIO[n] does not exist, then, the (n-64) bit in this register will always read as 0 and writes will have no effect. 3. After a full reset RSMRST# all multiplexed signals in the resume and core wells are configured as their default function. After only a PLTRST#, the GPIOs in the core well are configured as their default function. 4. When configured to GPIO mode, the multiplexing logic will present the inactive state to native logic that uses the pin as an input. 5. GPIO73 is a mobile only GPIO and not available on Desktop. 465 LPC Interface Bridge Registers (D31:F0) 12.10.15 GP_IO_SEL3--GPIO Input/Output Select 3 Register Offset Address: GPIOBASE +44h Default Value: 00000FF0h Lockable: Yes Attribute: R/W Size: 32 bits Power Well:Core for 0:7, 16:23, Resume for 8:15, 24:31 This register corresponds to GPIO[75:64]. Bit 0 corresponds to GPIO64 and bit 11 corresponds to GPIO75. Bit 31:12 11:0 Description Always 0. No corresponding GPIO. GP_IO_SEL3[75:64]--R/W. 0 = GPIO signal is programmed as an output. 1 = Corresponding GPIO signal (if enabled in the GPIO_USE_SEL3 register) is programmed as an input. 12.10.16 GP_LVL3--GPIO Level for Input or Output 3 Register Offset Address: GPIOBASE +48h Default Value: 000000C0h Lockable: Yes Attribute: R/W Size: 32 bits Power Well:Core for 0:7, 16:23, Resume for 8:15, 24:31 This register corresponds to GPIO[75:64]. Bit 0 corresponds to GPIO64 and bit 11 corresponds to GPIO75. Bit 31:12 11:0 Description Always 0. No corresponding GPIO. GP_LVL[75:64]--R/W. These registers are implemented as dual read/write with dedicated storage each. Write value will be stored in the write register, while read is coming from the read register which will always reflect the value of the pin. If GPIO[n] is programmed to be an output (using the corresponding bit in the GP_IO_SEL register), then the corresponding GP_LVL[n] write register value will drive a high or low value on the output pin. 1 = high, 0 = low. When configured in native mode (GPIO_USE_SEL[n] is 0), writes to these bits are stored but have no effect to the pin value. The value reported in this register is undefined when programmed as native mode. 12.10.17 GP_RST_SEL1--GPIO Reset Select Register Offset Address: GPIOBASE +60h Default Value: 01000000h Lockable: Yes Bit Description 31:24 GP_RST_SEL[31:24]--R/W. 0 = Corresponding GPIO registers will be reset by PWROK de-assertion, CF9h reset (06h or 0Eh), or SYS_RESET# assertion. 1 = Corresponding GPIO registers will be reset by RSMRST# assertion only. Note: GPIO[24] register bits are not cleared by CF9h reset by default. 23:16 Reserved 15:8 7:0 466 Attribute: R/W Size: 32 bits Power Well:Core for 0:7, 16:23, Resume for 8:15, 24:31 GP_RST_SEL[15:8]--R/W. 0 = Corresponding GPIO registers will be reset by PWROK de-assertion, CF9h reset (06h or 0Eh), or SYS_RESET# assertion. 1 = Corresponding GPIO registers will be reset by RSMRST# assertion only. Reserved Datasheet LPC Interface Bridge Registers (D31:F0) 12.10.18 GP_RST_SEL2--GPIO Reset Select Register Offset Address: GPIOBASE +64h Default Value: 00000000h Lockable: Yes Attribute: R/W Size: 32 bits Power Well:Core for 0:7, 16:23, Resume for 8:15, 24:31 Bit Description 31:24 GP_RST_SEL[63:56]--R/W. 0 = Corresponding GPIO registers will be reset by PWROK de-assertion, CF9h reset (06h or 0Eh), or SYS_RESET# assertion. 1 = Corresponding GPIO registers will be reset by RSMRST# assertion only. 23:16 Reserved 15:8 7:0 GP_RST_SEL[47:40]--R/W. 0 = Corresponding GPIO registers will be reset by PWROK de-assertion, CF9h reset (06h or 0Eh), or SYS_RESET# assertion. 1 = Corresponding GPIO registers will be reset by RSMRST# assertion only. Reserved 12.10.19 GP_RST_SEL3--GPIO Reset Select Register Offset Address: GPIOBASE +68h Default Value: 00000000h Lockable: Yes Bit 31:12 11:8 7:0 Attribute: R/W Size: 32 bits Power Well:Core for 0:7, 16:23, Resume for 8:15, 24:31 Description Reserved GP_RST_SEL[75:72]--R/W. 0 = Corresponding GPIO registers will be reset by PWROK de-assertion, CF9h reset (06h or 0Eh), or SYS_RESET# assertion. 1 = Corresponding GPIO registers will be reset by RSMRST# assertion only. Reserved Datasheet 467 SATA Controller Registers (D31:F2) 13 SATA Controller Registers (D31:F2) 13.1 PCI Configuration Registers (SATA-D31:F2) Note: Address locations that are not shown should be treated as Reserved. All of the SATA registers are in the core well. None of the registers can be locked. Table 13-1. SATA Controller PCI Register Address Map (SATA-D31:F2) (Sheet 1 of 2) 468 Offset Mnemonic Register Name Default Attribute 00h-01h VID Vendor Identification 8086h RO 02h-03h DID Device Identification See register description RO 04h-05h PCICMD 0000h R/W, RO 06h-07h PCISTS 08h RID Revision Identification 02B0h R/WC, RO See register description RO 09h PI Programming Interface See register description See register description 0Ah SCC Sub Class Code See register description See register description PCI Command PCI Status 0Bh BCC Base Class Code 01h RO 0Dh PMLT Primary Master Latency Timer 00h RO 0Eh HTYPE 10h-13h PCMD_BAR Primary Command Block Base Address Header Type 00h RO 00000001h R/W, RO 14h-17h PCNL_BAR Primary Control Block Base Address 00000001h R/W, RO 18h-1Bh SCMD_BAR Secondary Command Block Base Address 00000001h R/W, RO 1Ch-1Fh SCNL_BAR 20h-23h BAR 24h-27h ABAR / SIDPBA 2Ch-2Dh SVID Secondary Control Block Base Address 00000001h R/W, RO Legacy Bus Master Base Address 00000001h R/W, RO AHCI Base Address / SATA Index Data Pair Base Address See register description See register description Subsystem Vendor Identification 0000h R/WO 0000h R/WO 80h RO 2Eh-2Fh SID Subsystem Identification 34h CAP Capabilities Pointer 3Ch INT_LN Interrupt Line 00h R/W 3Dh INT_PN Interrupt Pin See register description RO 40h-41h IDE_TIM Primary IDE Timing 0000h R/W 42h-43h IDE_TIM Secondary IDE Timing 0000h R/W 44h SIDETIM Slave IDE Timing 00h R/W 48h SDMA_CNT Synchronous DMA Control 00h R/W 4Ah-4Bh SDMA_TIM Synchronous DMA Timing 54h-57h IDE_CONFIG IDE I/O Configuration 0000h R/W 00000000h R/W Datasheet SATA Controller Registers (D31:F2) Table 13-1. SATA Controller PCI Register Address Map (SATA-D31:F2) (Sheet 2 of 2) Offset Mnemonic 70h-71h PID 72h-73h PC 74h-75h Default Attribute PCI Power Management Capability Identification See register description RO PCI Power Management Capabilities See register description RO PMCS PCI Power Management Control and Status See register description R/W, RO, R/WC 80h-81h MSICI Message Signaled Interrupt Capability Identification 7005h RO 82h-83h MSIMC Message Signaled Interrupt Message Control 84h-87h MSIMA Message Signaled Interrupt Message Address 88h-89h MSIMD 90h MAP 92h-93h PCS 94h-97h SCLKCG RO, R/W RO, R/W Message Signaled Interrupt Message Data 0000h R/W Address Map 0000h R/W, R/WO Port Control and Status SATA Clock Gating Control 0000h R/W, RO 00000000h R/W 9Ch-9Fh SGC SATA General Configuration 00000000h R/W, R/WO SATACR0 SATA Capability Register 0 0010B012h RO, R/WO SATA Capability Register 1 00000048h RO 0009h RO See register description R/WO, RO 0000h RO, R/W ACh-AFh SATACR1 B0h-B1h FLRCID FLR Capability Identification B2h-B3h FLRCLV FLR Capability Length and Version B4h-B5h FLRC C0h ATC APM Trapping Control 00h R/W C4h ATS APM Trapping Status 00h R/WC D0h-D3h SP E0h-E3h BFCS FLR Control Scratch Pad 00000000h R/W BIST FIS Control/Status 00000000h R/W, R/WC E4h-E7h BFTD1 BIST FIS Transmit Data, DW1 00000000h R/W E8h-EBh BFTD2 BIST FIS Transmit Data, DW2 00000000h R/W The PCH SATA controller is not arbitrated as a PCI device; therefore, it does not need a master latency timer. VID--Vendor Identification Register (SATA--D31:F2) Offset Address: 00h-01h Default Value: 8086h Lockable: No Bit 15:0 Datasheet 0000h 00000000h A8h-ABh Note: 13.1.1 Register Name Attribute: RO Size: 16 bit Power Well:Core Description Vendor ID--RO. This is a 16-bit value assigned to Intel. Intel VID = 8086h 469 SATA Controller Registers (D31:F2) 13.1.2 DID--Device Identification Register (SATA--D31:F2) Offset Address: 02h-03h Default Value: See bit description Lockable: No Bit 15:0 Description Device ID--RO. This is a 16-bit value assigned to the PCH SATA controller. Note: 13.1.3 Attribute: RO Size: 16 bit Power Well:Core The value of this field will change dependent upon the value of the MAP Register. See Section 13.1.34 PCICMD--PCI Command Register (SATA-D31:F2) Address Offset: 04h-05h Default Value: 0000h Bit 15:11 10 470 Attribute: Size: RO, R/W 16 bits Description Reserved Interrupt Disable--R/W. This disables pin-based INTx# interrupts. This bit has no effect on MSI operation. 0 = Internal INTx# messages are generated if there is an interrupt and MSI is not enabled. 1 = Internal INTx# messages will not be generated. 9 Fast Back to Back Enable (FBE)--RO. Hardwired to 0. 8 SERR# Enable (SERR_EN)--RO. Hardwired to 0. 7 Wait Cycle Control (WCC)--RO. Hardwired to 0. 6 Parity Error Response (PER)--R/W. 0 = Disabled. SATA controller will not generate PERR# when a data parity error is detected. 1 = Enabled. SATA controller will generate PERR# when a data parity error is detected. 5 VGA Palette Snoop (VPS)--RO. Hardwired to 0. 4 Postable Memory Write Enable (PMWE)--RO. Hardwired to 0. 3 Special Cycle Enable (SCE)--RO. Hardwired to 0. 2 Bus Master Enable (BME)--R/W. This bit controls the SATA controller's ability to act as a master for data transfers. This bit does not impact the generation of completions for split transaction commands. 1 Memory Space Enable (MSE)--R/W / RO. Controls access to the SATA controller's target memory space (for AHCI). This bit is RO 0 when not in AHCI/RAID modes. 0 I/O Space Enable (IOSE)--R/W. This bit controls access to the I/O space registers. 0 = Disables access to the Legacy or Native IDE ports (both Primary and Secondary) as well as the Bus Master I/O registers. 1 = Enable. The Base Address register for the Bus Master registers should be programmed before this bit is set. Datasheet SATA Controller Registers (D31:F2) 13.1.4 PCISTS--PCI Status Register (SATA-D31:F2) Address Offset: 06h-07h Default Value: 02B0h Note: Description 15 Detected Parity Error (DPE)--R/WC. 0 = No parity error detected by SATA controller. 1 = SATA controller detects a parity error on its interface. 14 Signaled System Error (SSE)--RO. Hardwired to 0. 13 Received Master Abort (RMA)--R/WC. 0 = Master abort not generated. 1 = SATA controller, as a master, generated a master abort. 12 Reserved--R/WC. 11 Signaled Target Abort (STA)--RO. Hardwired to 0. 10:9 DEVSEL# Timing Status (DEV_STS)--RO. 01 = Hardwired; Controls the device select time for the SATA controller's PCI interface. 8 Data Parity Error Detected (DPED)--R/WC. For PCH, this bit can only be set on read completions received from the bus when there is a parity error. 0 = No data parity error received. 1 = SATA controller, as a master, either detects a parity error or sees the parity error line asserted, and the parity error response bit (bit 6 of the command register) is set. 7 Fast Back to Back Capable (FB2BC)--RO. Hardwired to 1. 6 Reserved 5 66MHz Capable (66MHZ_CAP)--RO. Hardwired to 1. 4 Capabilities List (CAP_LIST)--RO. This bit indicates the presence of a capabilities list. The minimum requirement for the capabilities list must be PCI power management for the SATA controller. 3 Interrupt Status (INTS)--RO. Reflects the state of INTx# messages, IRQ14 or IRQ15. 0 = Interrupt is cleared (independent of the state of Interrupt Disable bit in the command register [offset 04h]). 1 = Interrupt is to be asserted 2:0 Reserved RID--Revision Identification Register (SATA--D31:F2) Offset Address: 08h Default Value: See bit description Datasheet R/WC, RO 16 bits For the writable bits, software must write a 1 to clear bits that are set. Writing a 0 to the bit has no effect. Bit 13.1.5 Attribute: Size: Attribute: Size: RO 8 bits Bit Description 7:0 Revision ID--RO. This field indicates the device specific revision identifier. See Section 1.3 for the value of the RID Register. 471 SATA Controller Registers (D31:F2) 13.1.6 PI--Programming Interface Register (SATA-D31:F2) 13.1.6.1 When Sub Class Code Register (D31:F2:Offset 0Ah) = 01h Address Offset: 09h Default Value: 8Ah Bit 7 6:4 13.1.6.2 Attribute: Size: Description Reserved. This read-only bit is a 1 to indicate that the PCH supports bus master operation Reserved. Will always return 0. 3 Secondary Mode Native Capable (SNC)--RO. Hardwired to `1' to indicate secondary controller supports both legacy and native modes. 2 Secondary Mode Native Enable (SNE)--R/W. Determines the mode that the secondary channel is operating in. 0 = Secondary controller operating in legacy (compatibility) mode 1 = Secondary controller operating in native PCI mode. If this bit is set by software, then the PNE bit (bit 0 of this register) must also be set by software. While in theory these bits can be programmed separately, such a configuration is not supported by hardware. 1 Primary Mode Native Capable (PNC)--RO. Hardwired to `1' to indicate primary controller supports both legacy and native modes. 0 Primary Mode Native Enable (PNE)--R/W. Determines the mode that the primary channel is operating in. 0 = Primary controller operating in legacy (compatibility) mode. 1 = Primary controller operating in native PCI mode. If this bit is set by software, then the SNE bit (bit 2 of this register) must also be set by software simultaneously. When Sub Class Code Register (D31:F2:Offset 0Ah) = 04h Address Offset: 09h Default Value: 00h Bit 7:0 13.1.6.3 Attribute: Size: RO 8 bits Description Interface (IF)--RO. When configured as RAID, this register becomes read only 0. When Sub Class Code Register (D31:F2:Offset 0Ah) = 06h Address Offset: 09h Default Value: 01h Bit 7:0 472 R/W, RO 8 bits Attribute: Size: RO 8 bits Description Interface (IF)--RO. Indicates that the SATA Controller is an AHCI HBA that has a major revision of 1. Datasheet SATA Controller Registers (D31:F2) 13.1.7 SCC--Sub Class Code Register (SATA-D31:F2) Address Offset: 0Ah Default Value: See bit description Bit 7:0 Sub Class Code (SCC) This field specifies the sub-class code of the controller, per the table below: Note: SCC Register Value 00b 01h (IDE Controller) 01b 06h (AHCI Controller) 10b 04h (RAID Controller) Not all SCC values may be available for a given SKU. See Section 1.3 for details on storage controller capabilities. BCC--Base Class Code Register (SATA-D31:F2SATA-D31:F2) Address Offset: 0Bh Default Value: 01h Bit 7:0 13.1.9 Attribute: Size: Base Class Code (BCC)--RO. 01h = Mass storage device PMLT--Primary Master Latency Timer Register (SATA-D31:F2) Bit 7:0 Attribute: Size: RO 8 bits Description Master Latency Timer Count (MLTC)--RO. 00h = Hardwired. The SATA controller is implemented internally, and is not arbitrated as a PCI device, so it does not need a Master Latency Timer. HTYPE--Header Type Register (SATA-D31:F2) Address Offset: 0Eh Default Value: 00h Bit 7 6:0 Datasheet RO 8 bits Description Address Offset: 0Dh Default Value: 00h 13.1.10 RO 8 bits Description MAP.SMS (D31:F2:Offset 90h:bit 7:6) Value 13.1.8 Attribute: Size: Attribute: Size: RO 8 bits Description Multi-function Device (MFD)--RO. Indicates this SATA controller is not part of a multifunction device. Header Layout (HL)--RO. Indicates that the SATA controller uses a target device layout. 473 SATA Controller Registers (D31:F2) 13.1.11 PCMD_BAR--Primary Command Block Base Address Register (SATA-D31:F2) Address Offset: 10h-13h Default Value: 00000001h Bit 31:16 15:3 2:1 0 Note: 13.1.12 Attribute: Size: Description Reserved Base Address--R/W. This field provides the base address of the I/O space (8 consecutive I/O locations). Reserved Resource Type Indicator (RTE)--RO. Hardwired to 1 to indicate a request for I/O space. This 8-byte I/O space is used in native mode for the Primary Controller's Command Block. PCNL_BAR--Primary Control Block Base Address Register (SATA-D31:F2) Address Offset: 14h-17h Default Value: 00000001h Bit 31:16 15:2 Attribute: Size: Description Reserved Base Address--R/W. This field provides the base address of the I/O space (4 consecutive I/O locations). Reserved 0 Resource Type Indicator (RTE)--RO. Hardwired to 1 to indicate a request for I/O space. This 4-byte I/O space is used in native mode for the Primary Controller's Control Block. SCMD_BAR--Secondary Command Block Base Address Register (SATA D31:F2) Address Offset: 18h-1Bh Default Value: 00000001h Bit 31:16 15:3 2:1 0 Note: 474 R/W, RO 32 bits 1 Note: 13.1.13 R/W, RO 32 bits Attribute: Size: R/W, RO 32 bits Description Reserved Base Address--R/W. This field provides the base address of the I/O space (8 consecutive I/O locations). Reserved Resource Type Indicator (RTE)--RO. Hardwired to 1 to indicate a request for I/O space. This 8-byte I/O space is used in native mode for the Secondary Controller's Command Block. Datasheet SATA Controller Registers (D31:F2) 13.1.14 SCNL_BAR--Secondary Control Block Base Address Register (SATA D31:F2) Address Offset: 1Ch-1Fh Default Value: 00000001h Bit 31:16 15:2 R/W, RO 32 bits Description Reserved Base Address--R/W. This field provides the base address of the I/O space (4 consecutive I/O locations). 1 Reserved 0 Resource Type Indicator (RTE)--RO. Hardwired to 1 to indicate a request for I/O space. Note: 13.1.15 Attribute: Size: This 4-byte I/O space is used in native mode for the Secondary Controller's Control Block. BAR--Legacy Bus Master Base Address Register (SATA-D31:F2) Address Offset: 20h-23h Default Value: 00000001h Attribute: Size: R/W, RO 32 bits The Bus Master IDE interface function uses Base Address register 5 to request a 16byte I/O space to provide a software interface to the Bus Master functions. Only 12 bytes are actually used (6 bytes for primary, 6 bytes for secondary). Only bits [15:4] are used to decode the address. Bit 31:16 15:5 4 3:1 0 13.1.16 Description Reserved Base Address--R/W. This field provides the base address of the I/O space (16 consecutive I/O locations). Base--R/W / RO. When SCC is 01h, this bit will be R/W resulting in requesting 16B of I/O space. When SCC is not 01h, this bit will be Read Only 0, resulting in requesting 32B of I/O space. Reserved Resource Type Indicator (RTE)--RO. Hardwired to 1 to indicate a request for I/O space. ABAR/SIDPBA1--AHCI Base Address Register / Serial ATA Index Data Pair Base Address (SATA-D31:F2) When the programming interface is not IDE (that is, SCC is not 01h), this register is named ABAR. When the programming interface is IDE, this register becomes SIDPBA. Hardware does not clear those BA bits when switching from IDE component to non-IDE component or vice versa. BIOS is responsible for clearing those bits to 0 since the number of writable bits changes after component switching (as indicated by a change in SCC). In the case, this register will then have to be re-programmed to a proper value. Datasheet 475 SATA Controller Registers (D31:F2) 13.1.16.1 When SCC is not 01h When the programming interface is not IDE, the register represents a memory BAR allocating space for the AHCI memory registers defined in Section 13.4. Address Offset: 24-27h Attribute: R/W, RO Default Value: 00000000h Size: 32 bits Bit 31:11 10:4 3 2:1 0 Note: 13.1.16.2 Description Base Address (BA)--R/W. Base address of register memory space (aligned to 2 KB) Reserved Prefetchable (PF)--RO. Indicates that this range is not prefetchable Type (TP)--RO. Indicates that this range can be mapped anywhere in 32-bit address space. Resource Type Indicator (RTE)--RO. Hardwired to 0 to indicate a request for register memory space. The ABAR register must be set to a value of 0001_0000h or greater. When SCC is 01h When the programming interface is IDE, the register becomes an I/O BAR allocating 16 bytes of I/O space for the I/O-mapped registers defined in Section 13.2. Although 16 bytes of locations are allocated, only 8 bytes are used as SINDX and SDATA registers; with the remaining 8 bytes preserved for future enhancement. Attribute: R/WO Address Offset: 24h-27h Default Value: 00000001h Size: 32 bits Bit 31:16 15:4 3:1 0 13.1.17 Description Reserved Base Address (BA)--R/W. Base address of the I/O space. Reserved Resource Type Indicator (RTE)--RO. Indicates a request for I/O space. SVID--Subsystem Vendor Identification Register (SATA-D31:F2) Address Offset: 2Ch-2Dh Default Value: 0000h Lockable: No Function Level Reset:No 476 Attribute: R/WO Size: 16 bits Power Well:Core Bit Description 15:0 Subsystem Vendor ID (SVID)--R/WO. Value is written by BIOS. No hardware action taken on this value. Datasheet SATA Controller Registers (D31:F2) 13.1.18 SID--Subsystem Identification Register (SATA-D31:F2) Address Offset: 2Eh-2Fh Default Value: 0000h Lockable: No Function Level Reset: No Bit 15:0 13.1.19 Attribute: R/WO Size: 16 bits Power Well:Core Description Subsystem ID (SID)--R/WO. Value is written by BIOS. No hardware action taken on this value. CAP--Capabilities Pointer Register (SATA-D31:F2) Address Offset: 34h Default Value: 80h 13.1.20 Attribute: Size: Bit Description 7:0 Capabilities Pointer (CAP_PTR)--RO. Indicates that the first capability pointer offset is 80h. This value changes to 70h if the Sub Class Code (SCC) (Dev 31:F2:0Ah) is configure as IDE mode (value of 01). INT_LN--Interrupt Line Register (SATA-D31:F2) Address Offset: 3Ch Default Value: 00h Function Level Reset:No Bit 7:0 13.1.21 Attribute: Size: R/W 8 bits Description Interrupt Line--R/W. This field is used to communicate to software the interrupt line that the interrupt pin is connected to. Interrupt Line register is not reset by FLR. INT_PN--Interrupt Pin Register (SATA-D31:F2) Address Offset: 3Dh Default Value: See Register Description Datasheet RO 8 bits Attribute: Size: RO 8 bits Bit Description 7:0 Interrupt Pin--RO. This reflects the value of D31IP.SIP (Chipset Config Registers:Offset 3100h:bits 11:8). 477 SATA Controller Registers (D31:F2) 13.1.22 IDE_TIM--IDE Timing Register (SATA-D31:F2) Address Offset: Primary: 40h-41h Secondary: 42h-43h Default Value: 0000h Attribute: R/W Size: 16 bits Bits 14:12 and 9:0 of this register are R/W to maintain software compatibility. These bits have no effect on hardware. Bit 15 IDE Decode Enable (IDE)--R/W. Individually enable/disable the Primary or Secondary decode. 0 = Disable. 1 = Enables the PCH to decode the associated Command Block (1F0-1F7h for primary, 170-177h for secondary, or their native mode BAR equivalents) and Control Block (3F6h for primary, 376h for secondary, or their native mode BAR equivalents). This bit effects the IDE decode ranges for both legacy and native-mode decoding. 14:12 IDE_TIM Field 2--R/W. This field is R/W to maintain software compatibility. This field has no effect on hardware. 11:10 Reserved 9:0 13.1.23 Description IDE_TIM Field 1--R/W. This field is R/W to maintain software compatibility. This field has no effect on hardware. SIDETIM--Slave IDE Timing Register (SATA-D31:F2) Address Offset: 44h Default Value: 00h Note: 13.1.24 Attribute: Size: This register is R/W to maintain software compatibility. These bits have no effect on hardware. Bit Description 7:0 SIDETIM Field 1--R/W. This field is R/W to maintain software compatibility. This field has no effect on hardware. SDMA_CNT--Synchronous DMA Control Register (SATA-D31:F2) Address Offset: 48h Default Value: 00h Note: Attribute: Size: R/W 8 bits This register is R/W to maintain software compatibility. These bits have no effect on hardware. Bit 478 R/W 8 bits Description 7:4 Reserved 3:0 SDMA_CNT Field 1--R/W. This field is R/W to maintain software compatibility. This field has no effect on hardware. Datasheet SATA Controller Registers (D31:F2) 13.1.25 SDMA_TIM--Synchronous DMA Timing Register (SATA-D31:F2) Address Offset: 4Ah-4Bh Default Value: 0000h Note: Description 15:14 Reserved 13:12 SDMA_TIM Field 4--R/W. This field is R/W to maintain software compatibility. This field has no effect on hardware. 11:10 Reserved 9:8 SDMA_TIM Field 3--R/W. This field is R/W to maintain software compatibility. This field has no effect on hardware. 7:6 Reserved 5:4 SDMA_TIM Field 2--R/W. This field is R/W to maintain software compatibility. This field has no effect on hardware. 3:2 Reserved 1:0 SDMA_TIM Field 1--R/W. This field is R/W to maintain software compatibility. This field has no effect on hardware. IDE_CONFIG--IDE I/O Configuration Register (SATA-D31:F2) Address Offset: 54h-57h Default Value: 00000000h Note: Attribute: Size: Description 31:24 Reserved 23:12 IDE_CONFIG Field 2--R/W. This field is R/W to maintain software compatibility. This field has no effect on hardware. 11:8 7:0 Reserved IDE_CONFIG Field 1--R/W. This field is R/W to maintain software compatibility. This field has no effect on hardware. PID--PCI Power Management Capability Identification Register (SATA-D31:F2) Address Offset: 70h-71h Default Value: See Register Description Attribute: Size: RO 16 bits Bits Description 15:8 Next Capability (NEXT)--R/W. A8h is the location of the Serial ATA capability structure. A8h is the recommended setting for non-IDE mode. If the controller is to operate in IDE mode, BIOS is requested to program this field to 00h. Note: Refer to the SGC.REGLOCK description in order to lock the register to become RO. 7:0 Datasheet R/W 32 bits This register is R/W to maintain software compatibility. These bits have no effect on hardware. Bit 13.1.27 R/W 16 bits This register is R/W to maintain software compatibility. These bits have no effect on hardware. Bit 13.1.26 Attribute: Size: Capability ID (CID)--RO. Hardwired to 01h. Indicates that this pointer is a PCI power management. 479 SATA Controller Registers (D31:F2) 13.1.28 PC--PCI Power Management Capabilities Register (SATA-D31:F2) Address Offset: 72h-73h Default Value: See Register Description Bits 15:11 RO 16 bits Description PME Support (PME_SUP)--RO. 00000 = If SCC = 01h, indicates no PME support in IDE mode. 01000 = If SCC is not 01h, in a non-IDE mode, indicates PME# can be generated from the D3HOT state in the SATA host controller. 10 D2 Support (D2_SUP)--RO. Hardwired to 0. The D2 state is not supported 9 D1 Support (D1_SUP)--RO. Hardwired to 0. The D1 state is not supported 8:6 5 Auxiliary Current (AUX_CUR)--RO. PME# from D3COLD state is not supported, therefore this field is 000b. Device Specific Initialization (DSI)--RO. Hardwired to 0 to indicate that no device-specific initialization is required. 4 Reserved 3 PME Clock (PME_CLK)--RO. Hardwired to 0 to indicate that PCI clock is not required to generate PME#. 2:0 13.1.29 Attribute: Size: Version (VER)--RO. Hardwired to 011 to indicates support for Revision 1.2 of the PCI Power Management Specification. PMCS--PCI Power Management Control and Status Register (SATA-D31:F2) Address Offset: 74h-75h Default Value: 0008h Function Level Reset: No (Bits 8 and 15) Bits 15 Attribute: Size: R/W, R/WC 16 bits Description PME Status (PMES)--R/WC. Bit is set when a PME event is to be requested, and if this bit and PMEE is set, a PME# will be generated from the SATA controller Note: When SCC = 01h, hardware will automatically change the attribute of this bit to RO 0. Software is advised to clear PMEE and PMES together prior to changing SCC thru MAP.SMS. This bit is not reset by Function Level Reset. 14:9 8 Reserved PME Enable (PMEE)--R/W. When set, the SATA controller asserts PME# when exiting D3HOT on a wake event. Note: When SCCSCC = 01h, hardware will automatically change the attribute of this bit to RO 0. Software is advised to clear PMEE and PMES together prior to changing SCC thru MAP.SMS. This bit is not reset by Function Level Reset. 7:4 480 Reserved 3 No Soft Reset (NSFRST)--RO. These bits are used to indicate whether devices transitioning from D3HOT state to D0 state will perform an internal reset. 0 = Device transitioning from D3HOT state to D0 state perform an internal reset. 1 = Device transitioning from D3HOT state to D0 state do not perform an internal reset. Configuration content is preserved. Upon transition from the D3HOT state to D0 state initialized state, no additional operating system intervention is required to preserve configuration context beyond writing to the PowerState bits. Regardless of this bit, the controller transition from D3HOT state to D0 state by a system or bus segment reset will return to the state D0 uninitialized with only PME context preserved if PME is supported and enabled. 2 Reserved Datasheet SATA Controller Registers (D31:F2) Bits 1:0 13.1.30 Description Power State (PS)--R/W. These bits are used both to determine the current power state of the SATA controller and to set a new power state. 00 = D0 state 11 = D3HOT state When in the D3HOT state, the controller's configuration space is available; however, the I/O and memory spaces are not. Additionally, interrupts are blocked. MSICI--Message Signaled Interrupt Capability Identification Register (SATA-D31:F2) Address Offset: 80h-81h Default Value: 7005h Note: Attribute: Size: RO 16 bits There is no support for MSI when the software is operating in legacy (IDE) mode when AHCI is not enabled. Prior to switching from AHCI to IDE mode, software must make sure that MSI is disabled. Bits Description 15:8 Next Pointer (NEXT)--R/W. Indicates the next item in the list is the PCI power management pointer. BIOS may program this field to A8h indicating that the next item is Serial ATA Capability Structure. Note: Refer to the SGC.REGLOCK description in order to lock the register to become RO. This bit is not reset by a Function Level Reset 7:0 13.1.31 Capability ID (CID)--RO. Capabilities ID indicates MSI. MSIMC--Message Signaled Interrupt Message Control Register (SATA-D31:F2) Address Offset: 82h-83h Default Value: 0000h Note: R/W, RO 16 bits There is no support for MSI when the software is operating in legacy (IDE) mode when AHCI is not enabled. Prior to switching from AHCI to IDE mode, software must make sure that MSI is disabled. Bits 15:8 7 Datasheet Attribute: Size: Description Reserved 64-bit Address Capable (C64)--RO. Capable of generating a 32-bit message only. 481 SATA Controller Registers (D31:F2) Bits Description 6:4 Multiple Message Enable (MME)--RO. = 000 (and MSIE is set), a single MSI message will be generated for all SATA ports, and bits [15:0] of the message vector will be driven from MD[15:0]. For 6 port components: MME Value Driven on MSI Memory Write Bits[15:3] Bit[2] Bit[1] Bit[0] 000, 001, 010 MD[15:3] MD[2] MD[1] MD[0] 011 MD[15:3] Port Port Port Port Port Port 0: 1: 2: 3: 4: 5: 0 0 0 0 1 1 Port Port Port Port Port Port 0: 1: 2: 3: 4: 5: 0 0 1 1 0 0 Port Port Port Port Port Port 0: 1: 2: 3: 4: 5: 0 1 0 1 0 1 For 4 port components: MME Value Driven on MSI Memory Write Bits[15:3] Bit[2] Bit[1] Bit[0] 000, 001, 010 MD[15:3] MD[2] MD[1] MD[0] 011 MD[15:3] Port Port Port Port 0: 1: 4: 5: 0 0 1 1 Port Port Port Port 0: 1: 2: 3: 0 0 0 0 Port Port Port Port 0: 1: 2: 3: 0 1 0 1 All other MME values are reserved. If this field is set to one of these reserved values, the results are undefined. Note: The CCC interrupt is generated on unimplemented port (AHCI PI register bit equal to 0). If CCC interrupt is disabled, no MSI shall be generated for the port dedicated to the CCC interrupt. When CCC interrupt occurs, MD[2:0] is dependant on CCC_CTL.INT (in addition to MME). 3:1 0 13.1.32 Multiple Message Capable (MMC)--RO. MMC is not supported. MSI Enable (MSIE)--R/W /RO. If set, MSI is enabled and traditional interrupt pins are not used to generate interrupts. This bit is R/W when SC.SCC is not 01h and is read-only 0 when SCC is 01h. The CMD.ID bit has no effect on MSI. Note: Software must clear this bit to 0 to disable MSI first before changing the number of messages allocated in the MMC field. Software must also make sure this bit is cleared to `0' when operating in legacy mode (when GHC.AE = 0). MSIMA--Message Signaled Interrupt Message Address Register (SATA-D31:F2) Address Offset: 84h-87h Default Value: 00000000h Note: R/W 32 bits There is no support for MSI when the software is operating in legacy (IDE) mode when AHCI is not enabled. Prior to switching from AHCI to IDE mode, software must make sure that MSI is disabled. Bits 31:2 1:0 482 Attribute: Size: Description Address (ADDR)--R/W. Lower 32 bits of the system specified message address, always DWord aligned. Reserved Datasheet SATA Controller Registers (D31:F2) 13.1.33 MSIMD--Message Signaled Interrupt Message Data Register (SATA-D31:F2) Address Offset: 88h-89h Default Value: 0000h Note: 15:0 Description Data (DATA)--R/W. This 16-bit field is programmed by system software if MSI is enabled. Its content is driven onto the lower word of the data bus of the MSI memory write transaction. When the MME field is set to `001' or `010', bit [0] and bits [1:0] respectively of the MSI memory write transaction will be driven based on the source of the interrupt rather than from MD[2:0]. See the description of the MME field. MAP--Address Map Register (SATA-D31:F2) Address Offset: 90h Default Value: 0000h Function Level Reset:No (Bits 7:5 and 13:8 only) Bits 15:8 Attribute: Size: R/W, R/WO 16 bits Description Reserved 7:6 SATA Mode Select (SMS)--R/W. Software programs these bits to control the mode in which the SATA Controller should operate: 00b = IDE mode 01b = AHCI mode 10b = RAID mode 11b = Reserved Notes: 1. The SATA Function Device ID will change based on the value of this register. 2. When switching from AHCI or RAID mode to IDE mode, a 2 port SATA controller (Device 31, Function 5) will be enabled. 3. SW shall not manipulate SMS during runtime operation; that is. the OS will not do this. The BIOS may choose to switch from one mode to another during POST. 4. Not all register values may be available for a given SKU. See Section 1.3 for details on storage controller capabilities. These bits are not reset by Function Level Reset. 5 SATA Port-to-Controller Configuration (SC)--R/W. This bit changes the number of SATA ports available within each SATA Controller. 0 = Up to 4 SATA ports are available for Controller 1 (Device 31 Function 2) with ports [3:0] and up to 2 SATA ports are available for Controller 2 (Device 31 Function 5) with ports [5:4]. 1 = Up to 6 SATA ports are available for Controller 1 (Device 31 Function 2) with ports [5:0] and no SATA ports are available for Controller 2 (Device 31 Function 5). Note: This bit should be set to 1 in AHCI/RAID mode. This bit is not reset by Function Level Reset. 4:0 13.1.35 R/W 16 bits There is no support for MSI when the software is operating in legacy (IDE) mode when AHCI is not enabled. Prior to switching from AHCI to IDE mode, software must make sure that MSI is disabled. Bits 13.1.34 Attribute: Size: Reserved PCS--Port Control and Status Register (SATA-D31:F2) Address Offset: 92h-93h Default Value: 0000h Function Level Reset: No Attribute: Size: R/W, RO 16 bits By default, the SATA ports are set to the disabled state (bits [5:0] = 0). When enabled by software, the ports can transition between the on, partial, and slumber states and can detect devices. When disabled, the port is in the "off" state and cannot detect any devices. Datasheet 483 SATA Controller Registers (D31:F2) If an AHCI-aware or RAID enabled operating system is being booted, then system BIOS shall insure that all supported SATA ports are enabled prior to passing control to the OS. Once the AHCI aware OS is booted, it becomes the enabling/disabling policy owner for the individual SATA ports. This is accomplished by manipulating a port's PxSCTL and PxCMD fields. Because an AHCI or RAID aware OS will typically not have knowledge of the PxE bits and because the PxE bits act as master on/off switches for the ports, preboot software must insure that these bits are set to 1 prior to booting the OS, regardless as to whether or not a device is currently on the port. Bits Description 15 OOB Retry Mode (ORM)--R/W. 0 = The SATA controller will not retry after an OOB failure 1 = The SATA controller will continue to retry after an OOB failure until successful (infinite retry) 14 Reserved 13 Port 5 Present (P5P)--RO. The status of this bit may change at any time. This bit is cleared when the port is disabled using P5E. This bit is not cleared upon surprise removal of a device. 0 = No device detected. 1 = The presence of a device on Port 5 has been detected. 12 Port 4 Present (P4P)--RO. The status of this bit may change at any time. This bit is cleared when the port is disabled using P4E. This bit is not cleared upon surprise removal of a device. 0 = No device detected. 1 = The presence of a device on Port 4 has been detected. 11 Port 3 Present (P3P)--RO. The status of this bit may change at any time. This bit is cleared when the port is disabled using P3E. This bit is not cleared upon surprise removal of a device. 0 = No device detected. 1 = The presence of a device on Port 3 has been detected. Note: Bit may be Reserved depending on if port is available in the given SKU. See Section 1.3 for details if port is available. 10 Port 2 Present (P2P)--RO. The status of this bit may change at any time. This bit is cleared when the port is disabled using P2E. This bit is not cleared upon surprise removal of a device. 0 = No device detected. 1 = The presence of a device on Port 2 has been detected. Note: Bit may be Reserved depending on if port is available in the given SKU. See Section 1.3 for details if port is available. 9 Port 1 Present (P1P)--RO. The status of this bit may change at any time. This bit is cleared when the port is disabled using P1E. This bit is not cleared upon surprise removal of a device. 0 = No device detected. 1 = The presence of a device on Port 1 has been detected. 8 Port 0 Present (P0P)--RO. The status of this bit may change at any time. This bit is cleared when the port is disabled using P0E. This bit is not cleared upon surprise removal of a device. 0 = No device detected. 1 = The presence of a device on Port 0 has been detected. 7:6 484 Reserved 5 Port 5 Enabled (P5E)--R/W / RO. 0 = Disabled. The port is in the `off' state and cannot detect any devices. 1 = Enabled. The port can transition between the on, partial, and slumber states and can detect devices. Notes: 1. This bit takes precedence over P5CMD.SUD (offset ABAR+398h:bit 1) 2. If MAP.SC is 0, SCC is 01h, MAP.SPD[5] is 1h,or set to a PCIe* Port then this bit will be read only 0. 4 Port 4 Enabled (P4E)--R/W / RO. 0 = Disabled. The port is in the `off' state and cannot detect any devices. 1 = Enabled. The port can transition between the on, partial, and slumber states and can detect devices. Note: 1. This bit takes precedence over P4CMD.SUD (offset ABAR+318h:bit 1) 2. If MAP.SC is 0, SCC is 01h, MAP.SPD[4] is 1h,or set to a PCIe Port then this bit will be read only 0. Datasheet SATA Controller Registers (D31:F2) Datasheet Bits Description 3 Port 3 Enabled (P3E)--R/W / RO. 0 = Disabled. The port is in the `off' state and cannot detect any devices. 1 = Enabled. The port can transition between the on, partial, and slumber states and can detect devices. Notes: 1. This bit takes precedence over P3CMD.SUD (offset ABAR+298h:bit 1). When MAP.SPD[3] is 1 this is reserved and is read-only 0. 2. Bit may be Reserved and RO depending on if port is available in the given SKU. See Section 1.3 for details if port is available. 2 Port 2 Enabled (P2E)--R/W / RO. 0 = Disabled. The port is in the `off' state and cannot detect any devices. 1 = Enabled. The port can transition between the on, partial, and slumber states and can detect devices. Notes: 1. This bit takes precedence over P2CMD.SUD (offset ABAR+218h:bit 1). When MAP.SPD[2] is 1 this is reserved and is read-only 0. 2. Bit may be Reserved and RO depending on if port is available in the given SKU. See Section 1.3 for details if port is available. 1 Port 1 Enabled (P1E)--R/W / RO. 0 = Disabled. The port is in the `off' state and cannot detect any devices. 1 = Enabled. The port can transition between the on, partial, and slumber states and can detect devices. Note: This bit takes precedence over P1CMD.SUD (offset ABAR+198h:bit 1). When MAP.SPD[1] is 1 this is reserved and is read-only 0. 0 Port 0 Enabled (P0E)--R/W / RO. 0 = Disabled. The port is in the `off' state and cannot detect any devices. 1 = Enabled. The port can transition between the on, partial, and slumber states and can detect devices. Note: This bit takes precedence over P0CMD.SUD (offset ABAR+118h:bit 1). When MAP.SPD[0] is 1 this is reserved and is read-only 0. 485 SATA Controller Registers (D31:F2) 13.1.36 SCLKCG--SATA Clock Gating Control Register Address Offset: 94h-97h Default Value: 00000000h Bit Description Reserved 29:24 Port Clock Disable (PCD)--R/W. 0 = All clocks to the associated port logic will operate normally. 1 = The backbone clock driven to the associated port logic is gated and will not toggle. Bit 29: Port 5 Bit 28: Port 4 Bit 27: Port 3 BIt 26: Port 2 Bit 25: Port 1 Bit 24: Port 0 If a port is not available, software shall set the corresponding bit to 1. Software can also set the corresponding bits to 1 on ports that are disabled. Software cannot set the PCD [port x]=1 if the corresponding PCS.PxE=1 in either Dev31Func2 or Dev31Func5 (dual controller IDE mode) or AHCI GHC.PI[x] = "1". Reserved SGC--SATA General Configuration Register Address Offset: 9Ch-9Fh Default Value: 00000000h Function Level Reset: No Attribute: Size: R/W, R/WO 32 bits Bit Description 31 Register Lock (REGLOCK)--R/WO. 0 = Will not lock CAP.CAP_PTR, PID.NEXT, MSICI.NEXT, or SATACR0.NEXT 1 = Setting this bit will lock CAP.CAP_PTR, PID.NEXT, MSICI.NEXT, and SATACR0.NEXT. Once locked these register bits will become RO. BIOS is requested to program this field prior to IOS handoff. This bit is not reset by a Function Level Reset. 30:8 Reserved 7 (non-RAID Capable SKUs Only) Reserved 7 (RAID Capable SKUs Only) Alternate ID Enable (AIE)--R/WO. 0 = Clearing this bit when in RAID mode, the SATA Controller located at Device 31: Function 2 will report its Device ID as 2822h for all Desktop SKUs of the PCH or 282Ah for all Mobile SKUs of the PCH. Clearing this bit is required for the Intel Rapid Storage Technology driver (including the Microsoft* Windows Vista* OS and later in-box version of the driver) to load on the platform. Intel Smart Response Technology also requires that the bit be cleared in order to be enabled on the platform. 1 = Setting this bit when in RAID mode, the SATA Controller located at Device 31: Function 2 will report its Device ID as called out in the Section 1.4 for Desktop SKUs or 1E07h for all Mobile SKUs of the chipset. This setting will prevent the Intel Rapid Storage Technology driver (including the Microsoft Windows* OS in-box version of the driver) from loading on the platform. During the Microsoft Windows OS installation, the user will be required to "load" (formerly done by pressing the F6 button on the keyboard) the appropriate RAID storage driver that is enabled by this setting. This field is reset by PLTRST#. BIOS is required to reprogram the value of this bit after resuming from S3, S4 and S5. 6 Alternate ID Select (AIES)--R/WO. BIOS must write to this bit field. 5 Reserved - BIOS may write to this field. 4:1 486 R/W 32 bits 31:30 23:0 13.1.37 Attribute: Size: Reserved Datasheet SATA Controller Registers (D31:F2) 13.1.38 Bit Description 0 SATA 4-port All Master Configuration Indicator (SATA4PMIND)--RO. 0 = Normal configuration. 1 = Two IDE Controllers are implemented, each supporting two ports for a Primary Master and a Secondary Master. Note: BIOS must also make sure that corresponding port clocks are gated (using SCLKCG configuration register). SATACR0--SATA Capability Register 0 (SATA-D31:F2) Address Offset: A8h-ABh Default Value: 0010B012h Function Level Reset: No (Bits 15:8 only) Note: Description 31:24 Reserved 23:20 Major Revision (MAJREV)--RO. Major revision number of the SATA Capability Pointer implemented. 19:16 Minor Revision (MINREV)--RO. Minor revision number of the SATA Capability Pointer implemented. 15:8 7:0 Next Capability Pointer (NEXT)--R/WO. Points to the next capability structure. These bits are not reset by Function Level Reset. Capability ID (CAP)--RW. The value 00h indicates the final item in the SATA Capability List. Note: Refer to the SGC.REGLOCK description in order to lock the register to become RO. SATACR1--SATA Capability Register 1 (SATA-D31:F2) Address Offset: ACh-AFh Default Value: 00000048h Note: Attribute: Size: RO 32 bits When SCC is 01h, this register is read-only 0. Bit 31:16 Datasheet RO, R/WO 32 bits This register is read-only 0 when SCC is 01h. Bit 13.1.39 Attribute: Size: Description Reserved 15:4 BAR Offset (BAROFST)--RO. Indicates the offset into the BAR where the Index/Data pair are located (in DWord granularity). The Index and Data I/O registers are located at offset 10h within the I/O space defined by LBAR. A value of 004h indicates offset 10h. 000h = 0h offset 001h = 4h offset 002h = 8h offset 003h = Bh offset 004h = 10h offset ... FFFh = 3FFFh offset (max 16KB) 3:0 BAR Location (BARLOC)--RO. Indicates the absolute PCI Configuration Register address of the BAR containing the Index/Data pair (in DWord granularity). The Index and Data I/O registers reside within the space defined by LBAR in the SATA controller. A value of 8h indicates offset 20h, which is LBAR. 0000 - 0011b = reserved 0100b = 10h => BAR0 0101b = 14h => BAR1 0110b = 18h => BAR2 0111b = 1Ch => BAR3 1000b = 20h => LBAR 1001b = 24h => BAR5 1010-1110b = Reserved 1111b = Index/Data pair in PCI Configuration space. This is not supported in the PCH. 487 SATA Controller Registers (D31:F2) 13.1.40 FLRCID--FLR Capability Identification Register (SATA- D31:F2) Address Offset: B0-B1h Default Value: 0009h Bit 15:8 7:0 RO 16 bits Description Next Capability Pointer--RO. 00h indicates the final item in the capability list. Capability ID--RO. The value of this field depends on the FLRCSSEL (RCBA+3410h:bit 12) bit. FLRCSSEL (RCBA+3410h:bit 12) Value 13.1.41 Attribute: Size: Capability ID Register Value 0b 13h 1b 00h (Vendor Specific) FLRCLV--FLR Capability Length and Version Register (SATA-D31:F2) Address Offset: B2-B3h Attribute: Default Value: xx06h Size: Function Level Reset:No (Bit 9:8 Only when FLRCSSEL = 0) RO, R/WO 16 bits When FLRCSSEL (RCBA+3410h:bit 12) = 1, this register is RO. Bit 15:10 Reserved 9 FLR Capability--R/WO. 1 = Support for Function Level reset. This bit is not reset by the Function Level Reset. 8 TXP Capability--R/WO. 1 = Support for Transactions Pending (TXP) bit. TXP must be supported if FLR is supported. 7:0 13.1.42 Description Vendor-Specific Capability ID--RO. This field indicates the number of bytes of this Vendor Specific capability as required by the PCI specification. It has the value of 06h for the FLR capability. FLRC--FLR Control Register (SATA-D31:F2) Address Offset: B4h-B5h Default Value: 0000h Attribute: Size: RO, R/W 16 bits When FLRCSSEL (RCBA+3410h:bit 12) = 1, this register is RO. Bit 15:9 8 7:1 0 488 Description Reserved Transactions Pending (TXP)--RO. 0 = Controller has received all non-posted requests. 1 = Controller has issued non-posted requests which has not been completed. Reserved Initiate FLR--R/W. Used to initiate FLR transition. A write of 1 indicates FLR transition. Since hardware must not respond to any cycles till FLR completion the value read by software from this bit is 0. Datasheet SATA Controller Registers (D31:F2) 13.1.43 ATC--APM Trapping Control Register (SATA-D31:F2) Address Offset: C0h Default Value: 00h Function Level Reset:No Bit 7:4 13.1.44 Attribute: Size: R/W 8 bits Description Reserved 3 Secondary Slave Trap (SST)--R/W. Enables trapping and SMI# assertion on legacy I/O accesses to 170h-177h and 376h. The active device on the secondary interface must be device 1 for the trap and/or SMI# to occur. 2 Secondary Master Trap (SPT)--R/W. Enables trapping and SMI# assertion on legacy I/O accesses to 170h-177h and 376h. The active device on the secondary interface must be device 0 for the trap and/or SMI# to occur. 1 Primary Slave Trap (PST)--R/W. Enables trapping and SMI# assertion on legacy I/O accesses to 1F0h-1F7h and 3F6h. The active device on the primary interface must be device 1 for the trap and/ or SMI# to occur. 0 Primary Master Trap (PMT)--R/W. Enables trapping and SMI# assertion on legacy I/O accesses to 1F0h-1F7h and 3F6h. The active device on the primary interface must be device 0 for the trap and/or SMI# to occur. ATS--APM Trapping Status Register (SATA-D31:F2) Address Offset: C4h Default Value: 00h Function Level Reset:No Attribute: Size: R/WC 8 bits . Bit 7:4 13.1.45 Description Reserved 3 Secondary Slave Trap (SST)--R/WC. Indicates that a trap occurred to the secondary slave device. 2 Secondary Master Trap (SPT)--R/WC. Indicates that a trap occurred to the secondary master device. 1 Primary Slave Trap (PST)--R/WC. Indicates that a trap occurred to the primary slave device. 0 Primary Master Trap (PMT)--R/WC. Indicates that a trap occurred to the primary master device. SP--Scratch Pad Register (SATA-D31:F2) Address Offset: D0h Default Value: 00000000h Attribute: Size: R/W 32 bits . Bit 31:0 13.1.46 Description Data (DT)--R/W. This is a read/write register that is available for software to use. No hardware action is taken on this register. BFCS--BIST FIS Control/Status Register (SATA-D31:F2) Address Offset: E0h-E3h Default Value: 00000000h Bits 31:16 Datasheet Attribute: Size: R/W, R/WC 32 bits Description Reserved 489 SATA Controller Registers (D31:F2) Bits Description 15 Port 5 BIST FIS Initiate (P5BFI)--R/W. When a rising edge is detected on this bit field, the PCH initiates a BIST FIS to the device on Port 5, using the parameters specified in this register and the data specified in BFTD1 and BFTD2. The BIST FIS will only be initiated if a device on Port 5 is present and ready (not partial/slumber state). After a BIST FIS is successfully completed, software must disable and re-enable the port using the PxE bits at offset 92h prior to attempting additional BIST FISs or to return the PCH to a normal operational mode. If the BIST FIS fails to complete, as indicated by the BFF bit in the register, then software can clear then set the P5BFI bit to initiate another BIST FIS. This can be retried until the BIST FIS eventually completes successfully. 14 Port 4 BIST FIS Initiate (P4BFI)--R/W. When a rising edge is detected on this bit field, the PCH initiates a BIST FIS to the device on Port 4, using the parameters specified in this register and the data specified in BFTD1 and BFTD2. The BIST FIS will only be initiated if a device on Port 4 is present and ready (not partial/slumber state). After a BIST FIS is successfully completed, software must disable and re-enable the port using the PxE bits at offset 92h prior to attempting additional BIST FISs or to return the PCH to a normal operational mode. If the BIST FIS fails to complete, as indicated by the BFF bit in the register, then software can clear then set the P4BFI bit to initiate another BIST FIS. This can be retried until the BIST FIS eventually completes successfully. 13 Port 3 BIST FIS Initiate (P3BFI)--R/W. When a rising edge is detected on this bit field, the PCH initiates a BIST FIS to the device on Port 3, using the parameters specified in this register and the data specified in BFTD1 and BFTD2. The BIST FIS will only be initiated if a device on Port 3 is present and ready (not partial/slumber state). After a BIST FIS is successfully completed, software must disable and re-enable the port using the PxE bits at offset 92h prior to attempting additional BIST FISs or to return the PCH to a normal operational mode. If the BIST FIS fails to complete, as indicated by the BFF bit in the register, then software can clear then set the P3BFI bit to initiate another BIST FIS. This can be retried until the BIST FIS eventually completes successfully. Note: 12 Port 2 BIST FIS Initiate (P2BFI)--R/W. When a rising edge is detected on this bit field, the PCH initiates a BIST FIS to the device on Port 2, using the parameters specified in this register and the data specified in BFTD1 and BFTD2. The BIST FIS will only be initiated if a device on Port 2 is present and ready (not partial/slumber state). After a BIST FIS is successfully completed, software must disable and re-enable the port using the PxE bits at offset 92h prior to attempting additional BIST FISes or to return the PCH to a normal operational mode. If the BIST FIS fails to complete, as indicated by the BFF bit in the register, then software can clear then set the P2BFI bit to initiate another BIST FIS. This can be retried until the BIST FIS eventually completes successfully. Note: 11 490 This bit must be cleared by software prior to initiating a BIST FIS. BIST FIS Failed (BFF)--R/WC. 0 = Software clears this bit by writing a 1 to it. 1 = This bit is set any time a BIST FIS transmitted by PCH receives an R_ERR completion status from the device. Note: 9 Bit may be Reserved depending on if port is available in the given SKU. See Section 1.3 for details if port is available. BIST FIS Successful (BFS)--R/WC. 0 = Software clears this bit by writing a 1 to it. 1 = This bit is set any time a BIST FIS transmitted by PCH receives an R_OK completion status from the device. Note: 10 Bit may be Reserved depending on if port is available in the given SKU. See Section 1.3 for details if port is available. This bit must be cleared by software prior to initiating a BIST FIS. Port 1 BIST FIS Initiate (P1BFI)--R/W. When a rising edge is detected on this bit field, the PCH initiates a BIST FIS to the device on Port 1, using the parameters specified in this register and the data specified in BFTD1 and BFTD2. The BIST FIS will only be initiated if a device on Port 1 is present and ready (not partial/slumber state). After a BIST FIS is successfully completed, software must disable and re-enable the port using the PxE bits at offset 92h prior to attempting additional BIST FISes or to return the PCH to a normal operational mode. If the BIST FIS fails to complete, as indicated by the BFF bit in the register, then software can clear then set the P1BFI bit to initiate another BIST FIS. This can be retried until the BIST FIS eventually completes successfully. Datasheet SATA Controller Registers (D31:F2) 13.1.47 Bits Description 8 Port 0 BIST FIS Initiate (P0BFI)--R/W. When a rising edge is detected on this bit field, the PCH initiates a BIST FIS to the device on Port 0, using the parameters specified in this register and the data specified in BFTD1 and BFTD2. The BIST FIS will only be initiated if a device on Port 0 is present and ready (not partial/slumber state). After a BIST FIS is successfully completed, software must disable and re-enable the port using the PxE bits at offset 92h prior to attempting additional BIST FISes or to return the PCH to a normal operational mode. If the BIST FIS fails to complete, as indicated by the BFF bit in the register, then software can clear then set the P0BFI bit to initiate another BIST FIS. This can be retried until the BIST FIS eventually completes successfully. 7:2 BIST FIS Parameters (BFP)--R/W. These 6 bits form the contents of the upper 6 bits of the BIST FIS Pattern Definition in any BIST FIS transmitted by the PCH. This field is not port specific - its contents will be used for any BIST FIS initiated on port 0, port 1, port 2, or port 3. The specific bit definitions are: Bit 7: T - Far End Transmit mode Bit 6: A - Align Bypass mode Bit 5: S - Bypass Scrambling Bit 4: L - Far End Retimed Loopback Bit 3: F - Far End Analog Loopback Bit 2: P - Primitive bit for use with Transmit mode 1:0 Reserved BFTD1--BIST FIS Transmit Data1 Register (SATA-D31:F2) Address Offset: E4h-E7h Default Value: 00000000h 13.1.48 Attribute: Size: Bits Description 31:0 BIST FIS Transmit Data 1--R/W. The data programmed into this register will form the contents of the second DWord of any BIST FIS initiated by the PCH. This register is not port specific--its contents will be used for BIST FIS initiated on any port. Although the 2nd and 3rd DWs of the BIST FIS are only meaningful when the "T" bit of the BIST FIS is set to indicate "Far-End Transmit mode", this register's contents will be transmitted as the BIST FIS 2nd DW regardless of whether or not the "T" bit is indicated in the BFCS register (D31:F2:E0h). BFTD2--BIST FIS Transmit Data2 Register (SATA-D31:F2) Address Offset: E8h-EBh Default Value: 00000000h Datasheet R/W 32 bits Attribute: Size: R/W 32 bits Bits Description 31:0 BIST FIS Transmit Data 2--R/W. The data programmed into this register will form the contents of the third DWord of any BIST FIS initiated by the PCH. This register is not port specific--its contents will be used for BIST FIS initiated on any port. Although the 2nd and 3rd DWs of the BIST FIS are only meaningful when the "T" bit of the BIST FIS is set to indicate "Far-End Transmit mode", this register's contents will be transmitted as the BIST FIS 3rd DW regardless of whether or not the "T" bit is indicated in the BFCS register (D31:F2:E0h). 491 SATA Controller Registers (D31:F2) 13.2 Bus Master IDE I/O Registers (D31:F2) The bus master IDE function uses 16 bytes of I/O space, allocated using the BAR register, located in D31:F2 Configuration space, offset 20h. All bus master IDE I/O space registers can be accessed as byte, word, or DWord quantities. Reading reserved bits returns an indeterminate, inconsistent value, and writes to reserved bits have no affect (but should not be attempted). These registers are only used for legacy operation. Software must not use these registers when running AHCI. All I/O registers are reset by Function Level Reset. The register address I/O map is shown in Table 13-2. Table 13-2. Bus Master IDE I/O Register Address Map 492 BAR+ Offset Mnemonic 00h BMICP 01h -- 02h BMISP 03h -- Register Command Register Primary Reserved Bus Master IDE Status Register Primary Reserved 04h-07h BMIDP Bus Master IDE Descriptor Table Pointer Primary 08h BMICS Command Register Secondary 09h -- 0Ah BMISS 0Bh -- 0Ch-0Fh BMIDS 10h AIR 14h AIDR Reserved Bus Master IDE Status Register Secondary Reserved Default Attribute 00h R/W -- RO 00h R/W, R/WC, RO -- RO xxxxxxxxh R/W 00h R/W -- RO 00h R/W, R/WC, RO -- RO Bus Master IDE Descriptor Table Pointer Secondary xxxxxxxxh R/W AHCI Index Register 00000000h R/W, RO AHCI Index Data Register xxxxxxxxh R/W Datasheet SATA Controller Registers (D31:F2) 13.2.1 BMIC[P,S]--Bus Master IDE Command Register (D31:F2) Address Offset: Primary: BAR + 00h Secondary: BAR + 08h Default Value: 00h Bit 7:4 3 2:1 0 Size: 8 bits Reserved. Returns 0. Read / Write Control (R/WC)--R/W. This bit sets the direction of the bus master transfer. This bit must NOT be changed when the bus master function is active. 0 = Memory reads 1 = Memory writes Reserved. Returns 0. Start/Stop Bus Master (START)--R/W. 0 = All state information is lost when this bit is cleared. Master mode operation cannot be stopped and then resumed. If this bit is reset while bus master operation is still active (that is, the Bus Master IDE Active bit (D31:F2:BAR + 02h, bit 0) of the Bus Master IDE Status register for that IDE channel is set) and the drive has not yet finished its data transfer (the Interrupt bit in the Bus Master IDE Status register for that IDE channel is not set), the bus master command is said to be aborted and data transferred from the drive may be discarded instead of being written to system memory. 1 = Enables bus master operation of the controller. Bus master operation does not actually start unless the Bus Master Enable bit (D31:F2:04h, bit 2) in PCI configuration space is also set. Bus master operation begins when this bit is detected changing from 0 to 1. The controller will transfer data between the IDE device and memory only when this bit is set. Master operation can be halted by writing a 0 to this bit. This bit is intended to be cleared by software after the data transfer is completed, as indicated by either the Bus Master IDE Active bit being cleared or the Interrupt bit of the Bus Master IDE Status register for that IDE channel being set, or both. Hardware does not clear this bit automatically. If this bit is cleared to 0 prior to the DMA data transfer being initiated by the drive in a device to memory data transfer, then the PCH will not send DMAT to terminate the data transfer. SW intervention (such as, sending SRST) is required to reset the interface in this condition. BMIS[P,S]--Bus Master IDE Status Register (D31:F2) Address Offset: Primary: BAR + 02h Secondary: BAR + 0Ah Default Value: 00h Attribute: R/W, R/WC, RO Size: 8 bits Bit Description 7 Simplex Only--RO. 0 = Both bus master channels (primary and secondary) can be operated independently and can be used at the same time. 1 = Only one channel may be used at the same time. 6 Drive 1 DMA Capable--R/W. 0 = Not Capable. 1 = Capable. Set by device dependent code (BIOS or device driver) to indicate that drive 1 for this channel is capable of DMA transfers, and that the controller has been initialized for optimum performance. The PCH does not use this bit. It is intended for systems that do not attach BMIDE to the PCI bus. 5 Drive 0 DMA Capable--R/W. 0 = Not Capable 1 = Capable. Set by device dependent code (BIOS or device driver) to indicate that drive 0 for this channel is capable of DMA transfers, and that the controller has been initialized for optimum performance. The PCH does not use this bit. It is intended for systems that do not attach BMIDE to the PCI bus. 4:3 Datasheet R/W Description Note: 13.2.2 Attribute: Reserved. Returns 0. 493 SATA Controller Registers (D31:F2) Bit 13.2.3 Description 2 Interrupt--R/WC. 0 = Software clears this bit by writing a 1 to it. 1 = Set when a device FIS is received with the `I' bit set, provided that software has not disabled interrupts using the IEN bit of the Device Control Register. 1 Error--R/WC. 0 = Software clears this bit by writing a 1 to it. 1 = This bit is set when the controller encounters a target abort or master abort when transferring data on PCI. 0 Bus Master IDE Active (ACT)--RO. 0 = This bit is cleared by the PCH when the last transfer for a region is performed, where EOT for that region is set in the region descriptor. It is also cleared by the PCH when the Start Bus Master bit (D31:F2:BAR+ 00h, bit 0) is cleared in the Command register. When this bit is read as a 0, all data transferred from the drive during the previous bus master command is visible in system memory, unless the bus master command was aborted. 1 = Set by the PCH when the Start bit is written to the Command register. BMID[P,S]--Bus Master IDE Descriptor Table Pointer Register (D31:F2) Address Offset: Primary: BAR + 04h-07h Secondary: BAR + 0Ch-0Fh Default Value: All bits undefined R/W Size: 32 bits Bit Description 31:2 Address of Descriptor Table (ADDR)--R/W. The bits in this field correspond to bits [31:2] of the memory location of the Physical Region Descriptor (PRD). The Descriptor Table must be DWordaligned. The Descriptor Table must not cross a 64-K boundary in memory. 1:0 13.2.4 Attribute: Reserved AIR--AHCI Index Register (D31:F2) Address Offset: Primary: BAR + 10h Default Value: 00000000h Attribute: Size: R/W 32 bits This register is available only when SCC is not 01h. Bit 31:11 10:2 1:0 494 Description Reserved Index (INDEX)--R/W. This Index register is used to select the DWord offset of the Memory Mapped AHCI register to be accessed. A DWord, Word or Byte access is specified by the active byte enables of the I/O access to the Data register. Reserved Datasheet SATA Controller Registers (D31:F2) 13.2.5 AIDR--AHCI Index Data Register (D31:F2) Address Offset: Primary: BAR + 14h Default Value: All bits undefined Attribute: Size: R/W 32 bits This register is available only when SCC is not 01h. 13.3 Bit Description 31:0 Data (DATA)--R/W. This Data register is a "window" through which data is read or written to the AHCI memory mapped registers. A read or write to this Data register triggers a corresponding read or write to the memory mapped register pointed to by the Index register. The Index register must be setup prior to the read or write to this Data register. A physical register is not actually implemented as the data is actually stored in the memory mapped registers. Since this is not a physical register, the "default" value is the same as the default value of the register pointed to by Index. Serial ATA Index/Data Pair Superset Registers All of these I/O registers are in the core well. They are exposed only when SCC is 01h (that is, IDE programming interface). These are Index/Data Pair registers that are used to access the SerialATA superset registers (SerialATA Status (PxSSTS), SerialATA Control (PxSCTL) and SerialATA Error (PxSERR)). The I/O space for these registers is allocated through SIDPBA. Locations with offset from 08h to 0Fh are reserved for future expansion. Software-write operations to the reserved locations will have no effect while software-read operations to the reserved locations will return 0. 13.3.1 Offset Mnemonic Register 00h-03h SINDEX Serial ATA Index 04h-07h SDATA Serial ATA Data 08h-0Ch -- Reserved 0Ch-0Fh -- Reserved SINDX--Serial ATA Index Register (D31:F2) Address Offset: SIDPBA + 00h Default Value: 00000000h Bit 31:16 15.8 Datasheet Attribute: Size: R/W 32 bits Description Reserved Port Index (PIDX)--R/W. This Index field is used to specify the port of the SATA controller at which the port-specific SSTS, SCTL, and SERR registers are located. 00h = Primary Master (Port 0) 01h = Primary Slave (Port 2) 02h = Secondary Master (Port 1) 03h = Secondary Slave (Port 3) All other values are Reserved. 495 SATA Controller Registers (D31:F2) 13.3.2 Bit Description 7:0 Register Index (RIDX)--R/W. This index field is used to specify one out of three registers currently being indexed into. These three registers are the Serial ATA superset SStatus, SControl and SError memory registers and are port specific, hence for this SATA controller, there are four sets of these registers. Refer to Section 13.4.2.10, Section 13.4.2.11, and Section 13.4.2.12 for definitions of the SStatus, SControl and SError registers. 00h = SSTS 01h = SCTL 02h = SERR All other values are Reserved. SDATA--Serial ATA Data Register (D31:F2) Address Offset: SIDPBA + 04h Default Value: 00000000h 13.3.2.1 Attribute: Size: R/W 32 bits Bit Description 31:0 Data (DATA)--R/W. This Data register is a "window" through which data is read or written to from the register pointed to by the Serial ATA Index (SINDX) register above. A physical register is not actually implemented as the data is actually stored in the memory mapped registers. Since this is not a physical register, the "default" value is the same as the default value of the register pointed to by SINDX.RIDX field. PxSSTS--Serial ATA Status Register (D31:F2) Address Offset: Default Value: 00000000h Attribute: Size: RO 32 bits SDATA when SINDX.RIDX is 00h. This is a 32-bit register that conveys the current state of the interface and host. The PCH updates it continuously and asynchronously. When the PCH transmits a COMRESET to the device, this register is updated to its reset values. Bit 31:12 11:8 Description Reserved Interface Power Management (IPM)--RO. Indicates the current interface state: Value 0h Description Device not present or communication not established 1h Interface in active state 2h Interface in PARTIAL power management state 6h Interface in SLUMBER power management state All other values reserved. 7:4 Current Interface Speed (SPD)--RO. Indicates the negotiated interface communication speed. Value Description 0h Device not present or communication not established 1h Generation 1 communication rate negotiated 2h Generation 2 communication rate negotiated 3h Generation 3 communication rate negotiated All other values reserved The PCH Supports Generation 1 communication rates (1.5 Gb/s), Gen 2 rates (3.0 Gb/s) and Gen 3 rates (6.0Gb/s) 496 Datasheet SATA Controller Registers (D31:F2) Bit 3:0 Description Device Detection (DET)--RO. Indicates the interface device detection and Phy state: Value Description 0h No device detected and Phy communication not established 1h Device presence detected but Phy communication not established 3h Device presence detected and Phy communication established 4h Phy in offline mode as a result of the interface being disabled or running in a BIST loopback mode All other values reserved. 13.3.2.2 PxSCTL--Serial ATA Control Register (D31:F2) Address Offset: Default Value: 00000000h Attribute: Size: R/W, RO 32 bits SDATA when SINDX.RIDX is 01h. This is a 32-bit read-write register by which software controls SATA capabilities. Writes to the SControl register result in an action being taken by the PCH or the interface. Reads from the register return the last value written to it. Bit Description 31:20 Reserved 19:16 Port Multiplier Port (PMP)--R/W. This field is not used by AHCI. 15:12 Select Power Management (SPM)--R/W. This field is not used by AHCI. 11:8 Interface Power Management Transitions Allowed (IPM)--R/W. Indicates which power states the PCH is allowed to transition to: Value Description 0h No interface restrictions 1h Transitions to the PARTIAL state disabled 2h Transitions to the SLUMBER state disabled 3h Transitions to both PARTIAL and SLUMBER states disabled All other values reserved 7:4 Speed Allowed (SPD)--R/W. Indicates the highest allowable speed of the interface. This speed is limited by the CAP.ISS (ABAR+00h:bit 23:20) field. Value Description 0h No speed negotiation restrictions 1h Limit speed negotiation to Generation 1 communication rate 2h Limit speed negotiation to Generation 2 communication rate 3h Limit speed negotiation to Generation 3 communication rate All other values reserved. The PCH Supports Generation 1 communication rates (1.5 Gb/s), Gen 2 rates (3.0 Gb/s) and Gen 3 rates (6.0Gb/s) Datasheet 497 SATA Controller Registers (D31:F2) Bit 3:0 Description Device Detection Initialization (DET)--R/W. Controls the PCH's device detection and interface initialization. Value Description 0h No device detection or initialization action requested 1h Perform interface communication initialization sequence to establish communication. This is functionally equivalent to a hard reset and results in the interface being reset and communications re-initialized 4h Disable the Serial ATA interface and put Phy in offline mode All other values reserved. When this field is written to a 1h, the PCH initiates COMRESET and starts the initialization process. When the initialization is complete, this field shall remain 1h until set to another value by software. This field may only be changed to 1h or 4h when PxCMD.ST is 0. Changing this field while the PCH is running results in undefined behavior. 13.3.2.3 PxSERR--Serial ATA Error Register (D31:F2) Address Offset: Default Value: 00000000h Attribute: Size: R/WC 32 bits SDATA when SINDx.RIDX is 02h. Bits 26:16 of this register contains diagnostic error information for use by diagnostic software in validating correct operation or isolating failure modes. Bits 11:0 contain error information used by host software in determining the appropriate response to the error condition. If one or more of bits 11:8 of this register are set, the controller will stop the current transfer. Bit 31:27 Reserved 26 Exchanged (X): When set to one, this bit indicates that a change in device presence has been detected since the last time this bit was cleared. This bit shall always be set to 1 anytime a COMINIT signal is received. This bit is reflected in the P0IS.PCS bit. 25 Unrecognized FIS Type (F): Indicates that one or more FISs were received by the Transport layer with good CRC, but had a type field that was not recognized. 24 Transport state transition error (T): Indicates that an error has occurred in the transition from one state to another within the Transport layer since the last time this bit was cleared. 23 Link Sequence Error (S): Indicates that one or more Link state machine error conditions was encountered. The Link Layer state machine defines the conditions under which the link layer detects an erroneous transition. 22 Handshake (H). Indicates that one or more R_ERR handshake response was received in response to frame transmission. Such errors may be the result of a CRC error detected by the recipient, a disparity or 8b/10b decoding error, or other error condition leading to a negative handshake on a transmitted frame. 21 CRC Error (C). Indicates that one or more CRC errors occurred with the Link Layer. 20 Disparity Error (D). This field is not used by AHCI. 19 10b to 8b Decode Error (B). Indicates that one or more 10b to 8b decoding errors occurred. 18 Comm Wake (W). Indicates that a Comm Wake signal was detected by the Phy. 17 Phy Internal Error (I). Indicates that the Phy detected some internal error. 16 PhyRdy Change (N): When set to 1, this bit indicates that the internal PhyRdy signal changed state since the last time this bit was cleared. In the PCH, this bit will be set when PhyRdy changes from a 0 -> 1 or a 1 -> 0. The state of this bit is then reflected in the PxIS.PRCS interrupt status bit and an interrupt will be generated if enabled. Software clears this bit by writing a 1 to it. 15:12 498 Description Reserved Datasheet SATA Controller Registers (D31:F2) Bit Description 11 Internal Error (E). The SATA controller failed due to a master or target abort when attempting to access system memory. 10 Protocol Error (P). A violation of the Serial ATA protocol was detected. Note: The PCH does not set this bit for all protocol violations that may occur on the SATA link. 9 Persistent Communication or Data Integrity Error (C). A communication error that was not recovered occurred that is expected to be persistent. Persistent communications errors may arise from faulty interconnect with the device, from a device that has been removed or has failed, or a number of other causes. 8 Transient Data Integrity Error (T): A data integrity error occurred that was not recovered by the interface. 7:2 Reserved 1 Recovered Communications Error (M). Communications between the device and host was temporarily lost but was re-established. This can arise from a device temporarily being removed, from a temporary loss of Phy synchronization, or from other causes and may be derived from the PhyNRdy signal between the Phy and Link layers. 0 Recovered Data Integrity Error (I). A data integrity error occurred that was recovered by the interface through a retry operation or other recovery action. 13.4 AHCI Registers (D31:F2) Note: These registers are AHCI-specific and available when the PCH is properly configured. The Serial ATA Status, Control, and Error registers are special exceptions and may be accessed on all PCH components if properly configured; see Section 13.3 for details. The memory mapped registers within the SATA controller exist in non-cacheable memory space. Additionally, locked accesses are not supported. If software attempts to perform locked transactions to the registers, indeterminate results may occur. Register accesses shall have a maximum size of 64-bits; 64-bit access must not cross an 8-byte alignment boundary. All memory registers are reset by Function Level Reset unless specified otherwise. The registers are broken into two sections - generic host control and port control. The port control registers are the same for all ports, and there are as many registers banks as there are ports. Table 13-3. AHCI Register Address Map Datasheet ABAR + Offset Mnemonic 00-1Fh GHC 20h-FFh -- Register Generic Host Control Reserved 100h-17Fh P0PCR Port 0 port control registers 180h-1FFh P1PCR Port 1 port control registers 200h-27Fh P2PCR Port 2 port control registers Note: Registers may be Reserved depending on if port is available in the given SKU. See Section 1.3 for details if port is available. 280h-2FFh P3PCR Port 3 port control registers Note: Registers may be Reserved depending on if port is available in the given SKU. See Section 1.3 for details if port is available. 300h-37Fh P4PCR Port 4 port control registers 380h-3FFh P5PCR Port 5 port control registers 499 SATA Controller Registers (D31:F2) 13.4.1 AHCI Generic Host Control Registers (D31:F2) Table 13-4. Generic Host Controller Register Address Map ABAR + Offset Mnemonic 00h-03h CAP 04h-07h GHC 08h-0Bh 0Ch-0Fh Default Attribute Host Capabilities FF22FFC2h (desktop) DE127F03h (mobile) R/WO, RO Global PCH Control 00000000h R/W, RO IS Interrupt Status 00000000h R/WC PI Ports Implemented 00000000h R/WO, RO 10h-13h VS AHCI Version 00010300h RO 1Ch-1Fh EM_LOC Enclosure Management Location 01600002h RO 20h-23h EM_CTRL Enclosure Management Control 07010000h R/W, R/WO, RO 24h-27h CAP2 HBA Capabilities Extended 00000004h RO 003Fh R/WO C8h-C9h 13.4.1.1 Register RSTF Intel (R) RST Feature Capabilities CAP--Host Capabilities Register (D31:F2) Address Offset: ABAR + 00h-03h Default Value: FF22FFC2h (Desktop) DE127F03h (Mobile) Function Level Reset:No Attribute: Size: R/WO, RO 32 bits All bits in this register that are R/WO are reset only by PLTRST#. 500 Bit Description 31 Supports 64-bit Addressing (S64A)--RO. Indicates that the SATA controller can access 64bit data structures. The 32-bit upper bits of the port DMA Descriptor, the PRD Base, and each PRD entry are read/write. 30 Supports Command Queue Acceleration (SCQA)--R/WO. When set to 1, indicates that the SATA controller supports SATA command queuing using the DMA Setup FIS. The PCH handles DMA Setup FISes natively, and can handle auto-activate optimization through that FIS. 29 Supports SNotification Register (SSNTF)--R/WO. The PCH SATA Controller does not support the SNotification register. BIOS must write a 0 to this field. 28 Supports Mechanical Presence Switch (SMPS)--R/WO. When set to 1, indicates whether the SATA controller supports mechanical presence switches on its ports for use in Hot-Plug operations. This value is loaded by platform BIOS prior to OS initialization. If this bit is set, BIOS must also map the SATAGP pins to the SATA controller through GPIO space. 27 Supports Staggered Spin-up (SSS)--R/WO. Indicates whether the SATA controller supports staggered spin-up on its ports, for use in balancing power spikes. This value is loaded by platform BIOS prior to OS initialization. 0 = Staggered spin-up not supported. 1 = Staggered spin-up supported. 26 Supports Aggressive Link Power Management (SALP)--R/WO. 0 = Software shall treat the PxCMD.ALPE and PxCMD.ASP bits as reserved. 1 = The SATA controller supports auto-generating link requests to the partial or slumber states when there are no commands to process. 25 Supports Activity LED (SAL)--RO. Indicates that the SATA controller supports a single output pin (SATALED#) which indicates activity. Datasheet SATA Controller Registers (D31:F2) Bit 24 23:20 Supports Command List Override (SCLO)--R/WO. When set to 1, indicates that the Controller supports the PxCMD.CLO bit and its associated function. When cleared to 0, the Controller is not capable of clearing the BSY and DRQ bits in the Status register in order to issue a software reset if these bits are still set from a previous operation. Interface Speed Support (ISS)--R/WO. Indicates the maximum speed the SATA controller can support on its ports. 1h = 1.5 Gb/s; 2h =3 Gb/s; 3h = 6 Gb/s The default of this field is dependent upon the PCH SKU. If at least one PCH SATA port supports 6 Gb/s, the default will be 3h. If no PCH SATA ports support 6 Gb/s, then the default will be 2h and writes of 3h will be ignored by the PCH. See Section 1.3 for details on 6 Gb/s port availability. 19 Supports Non-Zero DMA Offsets (SNZO)--RO. Reserved, as per the AHCI Revision 1.3 specification 18 Supports AHCI Mode Only (SAM)--RO. The SATA controller may optionally support AHCI access mechanism only. 0 = SATA controller supports both IDE and AHCI Modes 1 = SATA controller supports AHCI Mode Only 17:16 Reserved 15 PIO Multiple DRQ Block (PMD)--RO. Hardwired to 1. The SATA controller supports PIO Multiple DRQ Command Block 14 Slumber State Capable (SSC)--R/WO. When set to 1, the SATA controller supports the slumber state. 13 Partial State Capable (PSC)--R/WO. When set to 1, the SATA controller supports the partial state. 12:8 Number of Command Slots (NCS)--RO. Hardwired to 1Fh to indicate support for 32 slots. 7 Command Completion Coalescing Supported (CCCS)--R/WO. 0 = Command Completion Coalescing Not Supported 1 = Command Completion Coalescing Supported 6 Enclosure Management Supported (EMS)--R/WO. 0 = Enclosure Management Not Supported 1 = Enclosure Management Supported 5 Supports External SATA (SXS)--R/WO. 0 = External SATA is not supported on any ports 1 = External SATA is supported on one or more ports When set, software can examine each SATA port's Command Register (PxCMD) to determine which port is routed externally. 4:0 13.4.1.2 Description Number of Ports (NPS)--RO. Indicates number of supported ports. The number of ports indicated in this field may be more than the number of ports indicated in the PI (ABAR + 0Ch) register. Field value dependent on number of ports available in a given SKU. See Section 1.3 for details. GHC--Global PCH Control Register (D31:F2) Address Offset: ABAR + 04h-07h Default Value: 00000000h R/W, RO 32 bits Bit Description 31 AHCI Enable (AE)--R/W. When set, this bit indicates that an AHCI driver is loaded and the controller will be talked to using AHCI mechanisms. This can be used by an PCH that supports both legacy mechanisms (such as SFF-8038i) and AHCI to know when the controller will not be talked to as legacy. 0 = Software will communicate with the PCH using legacy mechanisms. 1 = Software will communicate with the PCH using AHCI. The PCH will not have to allow command processing using both AHCI and legacy mechanisms. Software shall set this bit to 1 before accessing other AHCI registers. 30:3 Datasheet Attribute: Size: Reserved 501 SATA Controller Registers (D31:F2) Bit Description 2 MSI Revert to Single Message (MRSM)--RO. When set to 1 by hardware, this bit indicates that the host controller requested more than one MSI vector but has reverted to using the first vector only. When this bit is cleared to 0, the controller has not reverted to single MSI mode (that is, hardware is already in single MSI mode, software has allocated the number of messages requested, or hardware is sharing interrupt vectors if MC.MME < MC.MMC). "MC.MSIE = 1 (MSI is enabled) "MC.MMC > 0 (multiple messages requested) "MC.MME > 0 (more than one message allocated) "MC.MME!= MC.MMC (messages allocated not equal to number requested) When this bit is set to 1, single MSI mode operation is in use and software is responsible for clearing bits in the IS register to clear interrupts. This bit shall be cleared to 0 by hardware when any of the four conditions stated is false. This bit is also cleared to 0 when MC.MSIE = 1 and MC.MME = 0h. In this case, the hardware has been programmed to use single MSI mode, and is not "reverting" to that mode. For PCH, the controller shall always revert to single MSI mode when the number of vectors allocated by the host is less than the number requested. This bit is ignored when GHC.HR = 1. 1 Interrupt Enable (IE)--R/W. This global bit enables interrupts from the PCH. 0 = All interrupt sources from all ports are disabled. 1 = Interrupts are allowed from the AHCI controller. 0 Controller Reset (HR)--R/W. Resets the PCH AHCI controller. 0 = No effect 1 = When set by software, this bit causes an internal reset of the PCH AHCI controller. All state machines that relate to data transfers and queuing return to an idle condition, and all ports are re-initialized using COMRESET. Note: 13.4.1.3 For further details, consult Section 10.4.3 of the Serial ATA Advanced Host Controller Interface Specification, Revision 1.3. IS--Interrupt Status Register (D31:F2) Address Offset: ABAR + 08h-0Bh Default Value: 00000000h Attribute: Size: R/WC 32 bits This register indicates which of the ports within the controller have an interrupt pending and require service. Bit 31:6 502 Description Reserved. Returns 0. 5 Interrupt Pending Status Port[5] (IPS[5])--R/WC. 0 = No interrupt pending. 1 = Port 5 has an interrupt pending. Software can use this information to determine which ports require service after an interrupt. 4 Interrupt Pending Status Port[4] (IPS[4])--R/WC. 0 = No interrupt pending. 1 = Port 4 has an interrupt pending. Software can use this information to determine which ports require service after an interrupt. 3 Interrupt Pending Status Port[3] (IPS[3])--R/WC. 0 = No interrupt pending. 1 = Port 3 has an interrupt pending. Software can use this information to determine which ports require service after an interrupt. Note: Bit may be Reserved depending on if port is available in the given SKU. See Section 1.3 for details if port is available. 2 Interrupt Pending Status Port[2] (IPS[2])--R/WC. 0 = No interrupt pending. 1 = Port 2 has an interrupt pending. Software can use this information to determine which ports require service after an interrupt. Note: Bit may be Reserved depending on if port is available in the given SKU. See Section 1.3 for details if port is available. Datasheet SATA Controller Registers (D31:F2) 13.4.1.4 Bit Description 1 Interrupt Pending Status Port[1] (IPS[1])--R/WC. 0 = No interrupt pending. 1 = Port 1has an interrupt pending. Software can use this information to determine which ports require service after an interrupt. 0 Interrupt Pending Status Port[0] (IPS[0])--R/WC. 0 = No interrupt pending. 1 = Port 0 has an interrupt pending. Software can use this information to determine which ports require service after an interrupt. PI--Ports Implemented Register (D31:F2) Address Offset: ABAR + 0Ch-0Fh Default Value: 00000000h Function Level Reset:No Attribute: Size: R/WO, RO 32 bits This register indicates which ports are exposed to the PCH. It is loaded by platform BIOS. It indicates which ports that the device supports are available for software to use. For ports that are not available, software must not read or write to registers within that port. After BIOS issues initial write to this register, BIOS is requested to issue two reads to this register. If BIOS accesses any of the port specific AHCI address range before setting PI bit, BIOS is required to read the PI register before the initial write to the PI register. Bit 31:6 Datasheet Description Reserved. Returns 0. 5 Ports Implemented Port 5 (PI5)--R/WO. 0 = The port is not implemented. 1 = The port is implemented. This bit is read-only 0 if this is a PCIe Port, MAP.SC = 0 or SCC = 01h. 4 Ports Implemented Port 4 (PI4)--R/WO. 0 = The port is not implemented. 1 = The port is implemented. This bit is read-only 0 if this is a PCIe Port, MAP.SC = 0 or SCC = 01h. 3 Ports Implemented Port 3 (PI3)--R/WO. 0 = The port is not implemented. 1 = The port is implemented. Note: Bit may be Reserved and RO `0' depending on if port is available in the given SKU. See Section 1.3 for details if port is available. 2 Ports Implemented Port 2 (PI2)--R/WO. 0 = The port is not implemented. 1 = The port is implemented. Note: Bit may be Reserved and RO `0' depending on if port is available in the given SKU. See Section 1.3 for details if port is available. 1 Ports Implemented Port 1 (PI1)--R/WO. 0 = The port is not implemented. 1 = The port is implemented. 0 Ports Implemented Port 0 (PI0)--R/WO. 0 = The port is not implemented. 1 = The port is implemented. 503 SATA Controller Registers (D31:F2) 13.4.1.5 VS--AHCI Version Register (D31:F2) Address Offset: ABAR + 10h-13h Default Value: 00010300h Attribute: Size: RO 32 bits This register indicates the major and minor version of the AHCI specification. It is BCD encoded. The upper two bytes represent the major version number, and the lower two bytes represent the minor version number. Example: Version 3.12 would be represented as 00030102h. The current version of the specification is 1.30 (00010300h). Bit 31:16 15:0 13.4.1.6 Description Major Version Number (MJR)--RO. Indicates the major version is 1 Minor Version Number (MNR)--RO. Indicates the minor version is 30. EM_LOC--Enclosure Management Location Register (D31:F2) Address Offset: ABAR + 1Ch-1Fh Default Value: 01600002h Attribute: Size: RO 32 bits This register identifies the location and size of the enclosure management message buffer. This register is reserved if enclosure management is not supported (that is, CAP.EMS = 0). Bit 13.4.1.7 Description 31:16 Offset (OFST)--RO. The offset of the message buffer in DWords from the beginning of the ABAR. 15:0 Buffer Size (SZ)--RO. Specifies the size of the transmit message buffer area in DWords. The PCH SATA controller only supports transmit buffer. A value of 0 is invalid. EM_CTRL--Enclosure Management Control Register (D31:F2) Address Offset: ABAR + 20h-23h Default Value: 07010000h Attribute: Size: R/W, R/WO, RO 32 bits This register is used to control and obtain status for the enclosure management interface. This register includes information on the attributes of the implementation, enclosure management messages supported, the status of the interface, whether any message are pending, and is used to initiate sending messages. This register is reserved if enclosure management is not supported (CAP_EMS = 0). Bit 31:27 504 Description Reserved 26 Activity LED Hardware Driven (ATTR.ALHD)--R/WO. 1 = The SATA controller drives the activity LED for the LED message type in hardware and does not utilize software for this LED. The host controller does not begin transmitting the hardware based activity signal until after software has written CTL.TM=1 after a reset condition. 25 Transmit Only (ATTR.XMT)--RO. 0 = The SATA controller supports transmitting and receiving messages. 1 = The SATA controller only supports transmitting messages and does not support receiving messages. Datasheet SATA Controller Registers (D31:F2) Bit 24 23:20 Single Message Buffer (ATTR.SMB)--RO. 0 = There are separate receive and transmit buffers such that unsolicited messages could be supported. 1 = The SATA controller has one message buffer that is shared for messages to transmit and messages received. Unsolicited receive messages are not supported and it is software's responsibility to manage access to this buffer. Reserved 19 SGPIO Enclosure Management Messages (SUPP.SGPIO)--RO. 1 = The SATA controller supports the SGPIO register interface message type. 18 SES-2 Enclosure Management Messages (SUPP.SES2)--RO. 1 = The SATA controller supports the SES-2 message type. 17 SAF-TE Enclosure Management Messages (SUPP.SAFTE)--RO. 1 = The SATA controller supports the SAF-TE message type. 16 LED Message Types (SUPP.LED)--RO. 1 = The SATA controller supports the LED message type. 15:10 Reserved 9 Reset (RST):--R/W. 0 = A write of 0 to this bit by software will have no effect. 1 = When set by software, The SATA controller resets all enclosure management message logic and takes all appropriate reset actions to ensure messages can be transmitted / received after the reset. After the SATA controller completes the reset operation, the SATA controller sets the value to 0. 8 Transmit Message (CTL.TM)--R/W. 0 = A write of 0 to this bit by software will have no effect. 1 = When set by software, The SATA controller transmits the message contained in the message buffer. When the message is completely sent, the SATA controller sets the value to 0. Software must not change the contents of the message buffer while CTL.TM is set to 1. 7:1 0 13.4.1.8 Description Reserved Message Received (STS.MR):--RO. Message Received is not supported in the PCH. CAP2--HBA Capabilities Extended Register Address Offset: ABAR + 24h-27h Default Value: 00000004h Function Level Reset:No Bit 31:3 2 1:0 Datasheet Attribute: Size: RO 32 bits Description Reserved Automatic Partial to Slumber Transitions (APST) 0= Not supported 1= Supported Reserved 505 SATA Controller Registers (D31:F2) 13.4.1.9 RSTF--Intel(R) RST Feature Capabilities Register Address Offset: ABAR + C8h-C9h Default Value: 003Fh Function Level Reset:No Attribute: Size: R/WO 16 bits No hardware action is taken on this register. This register is needed for the Intel Rapid Storage Technology software. These bits are set by BIOS to request the feature from the appropriate Intel Rapid Storage Technology software. Bit 506 Description 15:12 Reserved 11:10 OROM UI Normal Delay (OUD)--R/WO. The values of these bits specify the delay of the OROM UI Splash Screen in a normal status. 00 = 2 Seconds (Default) 01 = 4 Seconds 10 = 6 Seconds 11 = 8 Seconds If bit 5 = 0b these values will be disregarded. 9 Intel(R) Smart Response Technology Enable Request (SEREQ)--R/WO. Indicates the requested status of the Intel Smart Response Technology support. 0 = Disabled 1 = Enabled 8 Intel(R) RRT Only on eSATA (ROES)--R/WO. Indicates the request that only Intel Rapid Recovery Technology (RRT) volumes can span internal and external SATA (eSATA). If not set, any RAID volume can span internal and external SATA. 0 = Disabled 1 = Enabled 7 Reserved 6 HDD Unlock (HDDLK)--R/WO Indicates the requested status of HDD password unlock in the OS. 0 = Disabled 1 = Enabled 5 Intel RST OROM UI (RSTOROMUI)--R/WO. Indicates the requested status of the Intel RST OROM UI display. 0 = The Intel RST OROM UI and banner are not displayed if all disks and RAID volumes have a normal status. 1 = The Intel RST OROM UI is displayed during each boot. 4 Intel(R) RRT Enable (RSTE)--R/WO Indicates the requested status of the Intel Rapid Recovery Technology support. 0 = Disabled 1 = Enabled 3 RAID 5 Enable (R5E)--R/WO Indicates the requested status of RAID 5 support. 0 = Disabled 1 = Enabled 2 RAID 10 Enable (R10E)--R/WO Indicates the requested status of RAID 10 support. 0 = Disabled 1 = Enabled 1 RAID 1 Enable (R1E)--R/WO Indicates the requested status of RAID 1 support. 0 = Disabled 1 = Enabled 0 RAID 0 Enable (R0E)--R/WO Indicates the requested status of RAID 0 support. 0 = Disabled 1 = Enabled Datasheet SATA Controller Registers (D31:F2) 13.4.2 Port Registers (D31:F2) Ports not available will result in the corresponding Port DMA register space being reserved. The controller shall ignore writes to the reserved space on write cycles and shall return 0 on read cycle accesses to the reserved location. Table 13-5. Port [5:0] DMA Register Address Map (Sheet 1 of 3) ABAR + Offset Datasheet Mnemonic 100h-103h P0CLB 104h-107h P0CLBU Register Port 0 Command List Base Address Port 0 Command List Base Address Upper 32-Bits 108h-10Bh P0FB 10Ch-10Fh P0FBU 110h-113h P0IS Port 0 Interrupt Status 114h-117h P0IE Port 0 Interrupt Enable 118h-11Bh P0CMD 11Ch-11Fh -- 120h-123h P0TFD Port 0 Task File Data 124h-127h P0SIG Port 0 Signature 128h-12Bh P0SSTS Port 0 Serial ATA Status 12Ch-12Fh P0SCTL Port 0 Serial ATA Control 130h-133h P0SERR Port 0 Serial ATA Error 134h-137h P0SACT Port 0 Serial ATA Active 138h-13Bh P0CI 13Ch-17Fh -- 180h-183h P1CLB 184h-187h P1CLBU Port 0 FIS Base Address Port 0 FIS Base Address Upper 32-Bits Port 0 Command Reserved Port 0 Command Issue Reserved Port 1 Command List Base Address Port 1 Command List Base Address Upper 32-Bits 188h-18Bh P1FB 18Ch-18Fh P1FBU Port 1 FIS Base Address 190h-193h P1IS Port 1 Interrupt Status 194h-197h P1IE Port 1 Interrupt Enable 198h-19Bh P1CMD 19Ch-19Fh -- 1A0h-1A3h P1TFD Port 1 Task File Data 1A4h-1A7h P1SIG Port 1 Signature 1A8h-1ABh P1SSTS Port 1 Serial ATA Status 1ACh-1AFh P1SCTL Port 1 Serial ATA Control 1B0h-1B3h P1SERR Port 1 Serial ATA Error 1B4h-1B7h P1SACT Port 1 Serial ATA Active 1B8h-1BBh P1CI 1BCh-1FFh -- Reserved 200h-27Fh -- Registers may be Reserved depending on if port is available in the given SKU. See Section 1.3 for details if port is available. 200h-203h P2CLB 204h-207h P2CLBU Port 1 FIS Base Address Upper 32-Bits Port 1 Command Reserved Port 1 Command Issue Port 2 Command List Base Address Port 2 Command List Base Address Upper 32-Bits 507 SATA Controller Registers (D31:F2) Table 13-5. Port [5:0] DMA Register Address Map (Sheet 2 of 3) ABAR + Offset 508 Mnemonic Register 208h-20Bh P2FB 20Ch-20Fh P2FBU 210h-213h P2IS Port 2 Interrupt Status 214h-217h P2IE Port 2 Interrupt Enable 218h-21Bh P2CMD 21Ch-21Fh -- 220h-223h P2TFD Port 2 Task File Data 224h-227h P2SIG Port 2 Signature 228h-22Bh P2SSTS Port 2 Serial ATA Status 22Ch-22Fh P2SCTL Port 2 Serial ATA Control 230h-233h P2SERR Port 2 Serial ATA Error 234h-237h P2SACT Port 2 Serial ATA Active 238h-23Bh P2CI 23Ch-27Fh -- Reserved 280h-2FFh -- Registers may be Reserved depending on if port is available in the given SKU. See Section 1.3 for details if port is available. 280h-283h P3CLB 284h-287h P3CLBU 288h-28Bh P3FB 28Ch-28Fh P3FBU 290h-293h P3IS 294h-297h P3IE 298h-29Bh P3CMD 29Ch-29Fh -- 2A0h-2A3h P3TFD Port 2 FIS Base Address Port 2 FIS Base Address Upper 32-Bits Port 2 Command Reserved Port 2 Command Issue Port 3 Command List Base Address Port 3 Command List Base Address Upper 32-Bits Port 3 FIS Base Address Port 3 FIS Base Address Upper 32-Bits Port 3 Interrupt Status Port 3 Interrupt Enable Port 3 Command Reserved Port 3 Task File Data 2A4h-2A7h P3SIG 2A8h-2ABh P3SSTS Port 3 Serial ATA Status 2ACh-2AFh P3SCTL Port 3 Serial ATA Control 2B0h-2B3h P3SERR Port 3 Serial ATA Error 2B4h-2B7h P3SACT Port 3 Serial ATA Active 2B8h-2BBh P3CI Port 3 Command Issue 2BCh-2FFh -- 300h-303h P4CLB 304h-307h P4CLBU 308h-30Bh P4FB 30Ch-30Fh P4FBU 310h-313h P4IS 314h-317h P4IE 318h-31Bh P4CMD 31Ch-31Fh -- 320h-323h P4TFD Port 3 Signature Reserved Port 4 Command List Base Address Port 4 Command List Base Address Upper 32-Bits Port 4 FIS Base Address Port 4 FIS Base Address Upper 32-Bits Port 4 Interrupt Status Port 4 Interrupt Enable Port 4 Command Reserved Port 4 Task File Data Datasheet SATA Controller Registers (D31:F2) Table 13-5. Port [5:0] DMA Register Address Map (Sheet 3 of 3) ABAR + Offset 13.4.2.1 Mnemonic 324h-327h P4SIG 328h-32Bh P4SSTS Port 4 Signature Port 4 Serial ATA Status 32Ch-32Fh P4SCTL Port 4 Serial ATA Control 330h-333h P4SERR Port 4 Serial ATA Error 334h-337h P4SACT Port 4 Serial ATA Active 338h-33Bh P4CI Port 4 Command Issue 33Ch-37Fh -- 380h-383h P5CLB Reserved Port 5 Command List Base Address 384h-387h P5CLBU 388h-38Bh P5FB 38Ch-38Fh P5FBU 390h-393h P5IS Port 5 Interrupt Status 394h-397h P5IE Port 5 Interrupt Enable 398h-39Bh P5CMD 39Ch-39Fh -- 3A0h-3A3h P5TFD 3A4h-3A7h P5SIG 3A8h-3ABh P5SSTS Port 5 Command List Base Address Upper 32-Bits Port 5 FIS Base Address Port 5 FIS Base Address Upper 32-Bits Port 5 Command Reserved Port 5 Task File Data Port 5 Signature Port 5 Serial ATA Status 3ACh-3AFh P5SCTL Port 5 Serial ATA Control 3B0h-3B3h P5SERR Port 5 Serial ATA Error 3B4h-3B7h P5SACT Port 5 Serial ATA Active 3B8h-3BBh P5CI Port 5 Command Issue 3BCh-FFFh -- Reserved PxCLB--Port [5:0] Command List Base Address Register (D31:F2) Address Offset: Port 0: ABAR Port 1: ABAR Port 2: ABAR Port 3: ABAR Port 4: ABAR Port 5: ABAR Default Value: Undefined + + + + + + 100h Attribute: R/W 180h 200h (if port available; see Section 1.3) 280h (if port available; see Section 1.3) 300h 380h Size: 32 bits Bit Description 31:10 Command List Base Address (CLB)--R/W. Indicates the 32-bit base for the command list for this port. This base is used when fetching commands to execute. The structure pointed to by this address range is 1 KB in length. This address must be 1-KB aligned as indicated by bits 31:10 being read/write. These bits are not reset on a controller reset. 9:0 Datasheet Register Reserved 509 SATA Controller Registers (D31:F2) 13.4.2.2 PxCLBU--Port [5:0] Command List Base Address Upper 32-Bits Register (D31:F2) Address Offset: Port 0: ABAR Port 1: ABAR Port 2: ABAR Port 3: ABAR Port 4: ABAR Port 5: ABAR Default Value: Undefined 13.4.2.3 Description 31:0 Command List Base Address Upper (CLBU)--R/W. Indicates the upper 32-bits for the command list base address for this port. This base is used when fetching commands to execute. These bits are not reset on a controller reset. PxFB--Port [5:0] FIS Base Address Register (D31:F2) + + + + + + 108h Attribute: R/W 188h 208h (if port available; see Section 1.3) 288h (if port available; see Section 1.3) 308h 388h Size: 32 bits Bit Description 31:8 FIS Base Address (FB)--R/W. Indicates the 32-bit base for received FISes. The structure pointed to by this address range is 256 bytes in length. This address must be 256-byte aligned, as indicated by bits 31:3 being read/write. These bits are not reset on a controller reset. 7:0 Reserved PxFBU--Port [5:0] FIS Base Address Upper 32-Bits Register (D31:F2) Address Offset: Port 0: ABAR Port 1: ABAR Port 2: ABAR Port 3: ABAR Port 4: ABAR Port 5: ABAR Default Value: Undefined Bit 31:0 510 104h Attribute: R/W 184h 204h (if port available; see Section 1.3) 284h (if port available; see Section 1.3) 304h 384h Size: 32 bits Bit Address Offset: Port 0: ABAR Port 1: ABAR Port 2: ABAR Port 3: ABAR Port 4: ABAR Port 5: ABAR Default Value: Undefined 13.4.2.4 + + + + + + + + + + + + 10Ch Attribute: R/W 18Ch 20Ch (if port available; see Section 1.3) 28Ch (if port available; see Section 1.3) 30Ch 38Ch Size: 32 bits Description FIS Base Address Upper (FBU)--R/W. Indicates the upper 32-bits for the received FIS base for this port. These bits are not reset on a controller reset. Datasheet SATA Controller Registers (D31:F2) 13.4.2.5 PxIS--Port [5:0] Interrupt Status Register (D31:F2) Address Offset: Port 0: ABAR Port 1: ABAR Port 2: ABAR Port 3: ABAR Port 4: ABAR Port 5: ABAR Default Value: 00000000h Bit 110h Attribute: R/WC, RO 190h 210h (if port available; see Section 1.3) 290h (if port available; see Section 1.3) 310h 390h Size: 32 bits Description 31 Cold Port Detect Status (CPDS)--RO. Cold presence detect is not supported. 30 Task File Error Status (TFES)--R/WC. This bit is set whenever the status register is updated by the device and the error bit (PxTFD.bit 0) is set. 29 Host Bus Fatal Error Status (HBFS)--R/WC. Indicates that the PCH encountered an error that it cannot recover from due to a bad software pointer. In PCI, such an indication would be a target or master abort. 28 Host Bus Data Error Status (HBDS)--R/WC. Indicates that the PCH encountered a data error (uncorrectable ECC / parity) when reading from or writing to system memory. 27 Interface Fatal Error Status (IFS)--R/WC. Indicates that the PCH encountered an error on the SATA interface which caused the transfer to stop. 26 Interface Non-fatal Error Status (INFS)--R/WC. Indicates that the PCH encountered an error on the SATA interface but was able to continue operation. 25 Reserved 24 Overflow Status (OFS)--R/WC. Indicates that the PCH received more bytes from a device than was specified in the PRD table for the command. 23 Incorrect Port Multiplier Status (IPMS)--R/WC. The PCH SATA controller does not support Port Multipliers. 22 PhyRdy Change Status (PRCS)--RO. When set to one, this bit indicates the internal PhyRdy signal changed state. This bit reflects the state of PxSERR.DIAG.N. Unlike most of the other bits in the register, this bit is RO and is only cleared when PxSERR.DIAG.N is cleared. The internal PhyRdy signal also transitions when the port interface enters partial or slumber power management states. Partial and slumber must be disabled when Surprise Removal Notification is desired, otherwise the power management state transitions will appear as false insertion and removal events. 21:8 Datasheet + + + + + + Reserved 7 Device Interlock Status (DIS)--R/WC. When set, this bit indicates that a platform mechanical presence switch has been opened or closed, which may lead to a change in the connection state of the device. This bit is only valid in systems that support an mechanical presence switch (CAP.SIS [ABAR+00:bit 28] set). For systems that do not support an mechanical presence switch, this bit will always be 0. 6 Port Connect Change Status (PCS)--RO. This bit reflects the state of PxSERR.DIAG.X. (ABAR+130h/1D0h/230h/2D0h, bit 26) Unlike other bits in this register, this bit is only cleared when PxSERR.DIAG.X is cleared. 0 = No change in Current Connect Status. 1 = Change in Current Connect Status. 5 Descriptor Processed (DPS)--R/WC. A PRD with the I bit set has transferred all its data. 4 Unknown FIS Interrupt (UFS)--RO. When set to 1, this bit indicates that an unknown FIS was received and has been copied into system memory. This bit is cleared to 0 by software clearing the PxSERR.DIAG.F bit to 0. This bit does not directly reflect the PxSERR.DIAG.F bit. PxSERR.DIAG.F is set immediately when an unknown FIS is detected, whereas this bit is set when the FIS is posted to memory. Software should wait to act on an unknown FIS until this bit is set to 1 or the two bits may become out of sync. 3 Set Device Bits Interrupt (SdBS)--R/WC. A Set Device Bits FIS has been received with the I bit set and has been copied into system memory. 2 DMA Setup FIS Interrupt (DSS)--R/WC. A DMA Setup FIS has been received with the I bit set and has been copied into system memory. 511 SATA Controller Registers (D31:F2) Bit 13.4.2.6 Description 1 PIO Setup FIS Interrupt (PSS)--R/WC. A PIO Setup FIS has been received with the I bit set, it has been copied into system memory, and the data related to that FIS has been transferred. 0 Device to Host Register FIS Interrupt (DHRS)--R/WC. A D2H Register FIS has been received with the I bit set, and has been copied into system memory. PxIE--Port [5:0] Interrupt Enable Register (D31:F2) Address Offset: Port 0: ABAR Port 1: ABAR Port 2: ABAR Port 3: ABAR Port 4: ABAR Port 5: ABAR Default Value: 00000000h + + + + + + 114h Attribute: R/W, RO 194h 214h (if port available; see Section 1.3) 294h (if port available; see Section 1.3) 314h 394h Size: 32 bits This register enables and disables the reporting of the corresponding interrupt to system software. When a bit is set (1) and the corresponding interrupt condition is active, then an interrupt is generated. Interrupt sources that are disabled (0) are still reflected in the status registers. Bit 31 Cold Presence Detect Enable (CPDE)--RO. Cold Presence Detect is not supported. 30 Task File Error Enable (TFEE)--R/W. When set, and GHC.IE and PxTFD.STS.ERR (due to a reception of the error register from a received FIS) are set, the PCH will generate an interrupt. 29 Host Bus Fatal Error Enable (HBFE)--R/W. When set, and GHC.IE and PxS.HBFS are set, the PCH will generate an interrupt. 28 Host Bus Data Error Enable (HBDE)--R/W. When set, and GHC.IE and PxS.HBDS are set, the PCH will generate an interrupt. 27 Host Bus Data Error Enable (HBDE)--R/W. When set, GHC.IE is set, and PxIS.HBDS is set, the PCH will generate an interrupt. 26 Interface Non-fatal Error Enable (INFE)--R/W. When set, GHC.IE is set, and PxIS.INFS is set, the PCH will generate an interrupt. 25 Reserved 24 Overflow Error Enable (OFE)--R/W. When set, and GHC.IE and PxS.OFS are set, the PCH will generate an interrupt. 23 Incorrect Port Multiplier Enable (IPME)--R/W. The PCH SATA controller does not support Port Multipliers. BIOS and storage software should keep this bit cleared to 0. 22 PhyRdy Change Interrupt Enable (PRCE)--R/W. When set, and GHC.IE is set, and PxIS.PRCS is set, the PCH shall generate an interrupt. 21:8 512 Description Reserved 7 Device Interlock Enable (DIE)--R/W. When set, and PxIS.DIS is set, the PCH will generate an interrupt. For systems that do not support an mechanical presence switch, this bit shall be a read-only 0. 6 Port Change Interrupt Enable (PCE)--R/W. When set, and GHC.IE and PxS.PCS are set, the PCH will generate an interrupt. 5 Descriptor Processed Interrupt Enable (DPE)--R/W. When set, and GHC.IE and PxS.DPS are set, the PCH will generate an interrupt. 4 Unknown FIS Interrupt Enable (UFIE)--R/W. When set, and GHC.IE is set and an unknown FIS is received, the PCH will generate this interrupt. 3 Set Device Bits FIS Interrupt Enable (SdBE)--R/W. When set, and GHC.IE and PxS.SdBS are set, the PCH will generate an interrupt. 2 DMA Setup FIS Interrupt Enable (DSE)--R/W. When set, and GHC.IE and PxS.DSS are set, the PCH will generate an interrupt. Datasheet SATA Controller Registers (D31:F2) Bit 13.4.2.7 Description 1 PIO Setup FIS Interrupt Enable (PSE)--R/W. When set, and GHC.IE and PxS.PSS are set, the PCH will generate an interrupt. 0 Device to Host Register FIS Interrupt Enable (DHRE)--R/W. When set, and GHC.IE and PxS.DHRS are set, the PCH will generate an interrupt. PxCMD--Port [5:0] Command Register (D31:F2) Address Offset: Port 0: ABAR + 118h Attribute: R/W, RO, R/WO Port 1: ABAR + 198h Port 2: ABAR + 218h (if port available; see Section 1.3) Port 3: ABAR + 298h (if port available; see Section 1.3) Port 4: ABAR + 318h Port 5: ABAR + 398h Default Value: 0000w00wh Size: 32 bits where w = 00?0b (for?, see bit description) Function Level Reset:No (Bit 21, 19 and 18 only) Bit Description 31:28 Interface Communication Control (ICC)--R/W.This is a four bit field that can be used to control reset and power states of the interface. Writes to this field will cause actions on the interface, either as primitives or an OOB sequence, and the resulting status of the interface will be reported in the PxSSTS register (Address offset Port 0:ABAR+124h, Port 1: ABAR+1A4h, Port 2: ABAR+224h, Port 3: ABAR+2A4h, Port 4: ABAR+224h, Port 5: ABAR+2A4h). Value Fh-7h 6h Definition Reserved Slumber: This will cause the PCH to request a transition of the interface to the slumber state. The SATA device may reject the request and the interface will remain in its current state 5h-3h Reserved 2h Partial: This will cause the PCH to request a transition of the interface to the partial state. The SATA device may reject the request and the interface will remain in its current state. 1h Active: This will cause the PCH to request a transition of the interface into the active 0h No-Op / Idle: When software reads this value, it indicates the PCH is not in the process of changing the interface state or sending a device reset, and a new link command may be issued. When system software writes a non-reserved value other than No-Op (0h), the PCH will perform the action and update this field back to Idle (0h). If software writes to this field to change the state to a state the link is already in (such as, interface is in the active state and a request is made to go to the active state), the PCH will take no action and return this field to Idle. Note: Datasheet When the ALPE bit (bit 26) is set, this register should not be set to 02h or 06h. 27 Aggressive Slumber / Partial (ASP)--R/W. When set to 1, and the ALPE bit (bit 26) is set, the PCH shall aggressively enter the slumber state when it clears the PxCI register and the PxSACT register is cleared. When cleared, and the ALPE bit is set, the PCH will aggressively enter the partial state when it clears the PxCI register and the PxSACT register is cleared. If CAP.SALP is cleared to 0, software shall treat this bit as reserved. 26 Aggressive Link Power Management Enable (ALPE)--R/W. When set to 1, the PCH will aggressively enter a lower link power state (partial or slumber) based upon the setting of the ASP bit (bit 27). 25 Drive LED on ATAPI Enable (DLAE)--R/W. When set to 1, the PCH will drive the LED pin active for ATAPI commands (PxCLB[CHz.A] set) in addition to ATA commands. When cleared, the PCH will only drive the LED pin active for ATA commands. See Section 5.17.10 for details on the activity LED. 513 SATA Controller Registers (D31:F2) Bit Description 24 Device is ATAPI (ATAPI)--R/W. When set to 1, the connected device is an ATAPI device. This bit is used by the PCH to control whether or not to generate the desktop LED when commands are active. See Section 5.17.10 for details on the activity LED. 23 Automatic Partial Slumber Transitions Enabled (APSTE)--R/W. 0 = This port will not perform Automatic Partial to Slumber Transitions. 1 = The HBA may perform Automatic Partial to Slumber Transitions. Note: Reserved 21 External SATA Port (ESP)--R/WO. 0 = This port supports internal SATA devices only. 1 = This port will be used with an external SATA device and Hot-Plug is supported. When set, CAP.SXS must also be set. This bit is not reset by Function Level Reset. 20 Reserved 19 Mechanical Switch Attached to Port (MPSP)--R/WO. If set to 1, the PCH supports a mechanical presence switch attached to this port. The PCH takes no action on the state of this bit - it is for system software only. For example, if this bit is cleared, and an mechanical presence switch toggles, the PCH still treats it as a proper mechanical presence switch event. Note: 18 This bit is not reset on a Controller reset or by a Function Level Reset. Hot-Plug Capable Port (HPCP)--R/WO. 0 = Port is not capable of Hot-Plug. 1 = Port is Hot-Plug capable. This indicates whether the platform exposes this port to a device which can be Hot-Plugged. SATA by definition is hot-pluggable, but not all platforms are constructed to allow the device to be removed (it may be screwed into the chassis, for example). This bit can be used by system software to indicate a feature such as "eject device" to the end-user. The PCH takes no action on the state of this bit - it is for system software only. For example, if this bit is cleared, and a HotPlug event occurs, the PCH still treats it as a proper Hot-Plug event. Note: 17:16 This bit is not reset on a Controller reset or by a Function Level Reset. Reserved 15 Controller Running (CR)--RO. When this bit is set, the DMA engines for a port are running. 14 FIS Receive Running (FR)--RO. When set, the FIS Receive DMA engine for the port is running. 13 Mechanical Presence Switch State (MPSS)--RO. The MPSS bit reports the state of a mechanical presence switch attached to this port. If CAP.SMPS is set to 1 and the mechanical presence switch is closed then this bit is cleared to 0. If CAP.SMPS is set to 1 and the mechanical presence switch is open then this bit is set to 1. If CAP.SMPS is set to '0' then this bit is cleared to 0. Software should only use this bit if both CAP.SMPS and PxCMD.MPSP are set to 1. 12:8 Current Command Slot (CCS)--RO. Indicates the current command slot the PCH is processing. This field is valid when the ST bit is set in this register, and is constantly updated by the PCH. This field can be updated as soon as the PCH recognizes an active command slot, or at some point soon after when it begins processing the command. This field is used by software to determine the current command issue location of the PCH. In queued mode, software shall not use this field, as its value does not represent the current command being executed. Software shall only use PxCI and PxSACT when running queued commands. 7:5 4 514 Software should only set this bit to `1' if CAP2.APST is set to `1'. 22 Reserved FIS Receive Enable (FRE)--R/W. When set, the PCH may post received FISes into the FIS receive area pointed to by PxFB (ABAR+108h/188h/208h/288h) and PxFBU (ABAR+10Ch/18Ch/ 20Ch/28Ch). When cleared, received FISes are not accepted by the PCH, except for the first D2H (device-to-host) register FIS after the initialization sequence. System software must not set this bit until PxFB (PxFBU) have been programmed with a valid pointer to the FIS receive area, and if software wishes to move the base, this bit must first be cleared, and software must wait for the FR bit (bit 14) in this register to be cleared. Datasheet SATA Controller Registers (D31:F2) 13.4.2.8 Bit Description 3 Command List Override (CLO)--R/W. Setting this bit to 1 causes PxTFD.STS.BSY and PxTFD.STS.DRQ to be cleared to 0. This allows a software reset to be transmitted to the device regardless of whether the BSY and DRQ bits are still set in the PxTFD.STS register. The Controller sets this bit to 0 when PxTFD.STS.BSY and PxTFD.STS.DRQ have been cleared to 0. A write to this register with a value of 0 shall have no effect. This bit shall only be set to 1 immediately prior to setting the PxCMD.ST bit to 1 from a previous value of 0. Setting this bit to 1 at any other time is not supported and will result in indeterminate behavior. Software must wait for CLO to be cleared to 0 before setting PxCMD.ST to 1. 2 Power On Device (POD)--RO. Cold presence detect not supported. Defaults to 1. 1 Spin-Up Device (SUD)--R/W / RO This bit is R/W and defaults to 0 for systems that support staggered spin-up (R/W when CAP.SSS (ABAR+00h:bit 27) is 1). Bit is RO 1 for systems that do not support staggered spin-up (when CAP.SSS is 0). 0 = No action. 1 = On an edge detect from 0 to 1, the PCH starts a COMRESET initialization sequence to the device. Clearing this bit to 0 does not cause any OOB signal to be sent on the interface. When this bit is cleared to 0 and PxSCTL.DET=0h, the controller will enter listen mode. 0 Start (ST)--R/W. When set, the PCH may process the command list. When cleared, the PCH may not process the command list. Whenever this bit is changed from a 0 to a 1, the PCH starts processing the command list at entry 0. Whenever this bit is changed from a 1 to a 0, the PxCI register is cleared by the PCH upon the PCH putting the controller into an idle state. Refer to Section 10.3 of the Serial ATA AHCI Specification for important restrictions on when ST can be set to 1 and cleared to 0. PxTFD--Port [5:0] Task File Data Register (D31:F2) Address Offset: Port 0: ABAR Port 1: ABAR Port 2: ABAR Port 3: ABAR Port 4: ABAR Port 5: ABAR Default Value: 0000007Fh + + + + + + 120h Attribute: RO 1A0h 220h (if port available; see Section 1.3) 2A0h (if port available; see Section 1.3) 320h 3A0h Size: 32 bits This is a 32-bit register that copies specific fields of the task file when FISes are received. The FISes that contain this information are: D2H Register FIS,PIO Setup FIS and Set Device Bits FIS. Bit 31:16 15:8 7:0 Datasheet Description Reserved Error (ERR)--RO. Contains the latest copy of the task file error register. Status (STS)--RO. Contains the latest copy of the task file status register. Fields in this register that affect AHCI. Bit Field 7 BSY Indicates the interface is busy Definition 6:4 N/A Not applicable 3 DRQ Indicates a data transfer is requested 2:1 N/A Not applicable 0 ERR Indicates an error during the transfer 515 SATA Controller Registers (D31:F2) 13.4.2.9 PxSIG--Port [5:0] Signature Register (D31:F2) Address Offset: Port 0: ABAR Port 1: ABAR Port 2: ABAR Port 3: ABAR Port 4: ABAR Port 5: ABAR Default Value: FFFFFFFFh + + + + + + 124h Attribute: RO 1A4h 224h (if port available; see Section 1.3) 2A4h (if port available; see Section 1.3) 324h 3A4h Size: 32 bits This is a 32-bit register which contains the initial signature of an attached device when the first D2H Register FIS is received from that device. It is updated once after a reset sequence. Bit Description 31:0 Signature (SIG)--RO. Contains the signature received from a device on the first D2H register FIS. The bit order is as follows: Bit 31:24 23:16 LBA Mid Register 15:8 LBA Low Register 7:0 13.4.2.10 Field LBA High Register Sector Count Register PxSSTS--Port [5:0] Serial ATA Status Register (D31:F2) Address Offset: Port 0: ABAR Port 1: ABAR Port 2: ABAR Port 3: ABAR Port 4: ABAR Port 5: ABAR Default Value: 00000000h + + + + + + 128h Attribute: RO 1A8h 228h (if port available; see Section 1.3) 2A8h (if port available; see Section 1.3) 328h 3A8h Size: 32 bits This is a 32-bit register that conveys the current state of the interface and host. The PCH updates it continuously and asynchronously. When the PCH transmits a COMRESET to the device, this register is updated to its reset values. Bit 31:12 11:8 Description Reserved Interface Power Management (IPM)--RO. Indicates the current interface state: Value 0h Description Device not present or communication not established 1h Interface in active state 2h Interface in PARTIAL power management state 6h Interface in SLUMBER power management state All other values reserved. 516 Datasheet SATA Controller Registers (D31:F2) Bit 7:4 Description Current Interface Speed (SPD)--RO. Indicates the negotiated interface communication speed. Value Description 0h Device not present or communication not established 1h Generation 1 communication rate negotiated 2h Generation 2 communication rate negotiated 3h Generation 3 communication rate negotiated All other values reserved. The PCH supports Gen 1 communication rates (1.5 Gb/s), Gen 2 rates (3.0 Gb/s) and Gen 3 rates (6.0 Gb/s) (supported speeds are determined by SKU; see Section 1.3) 3:0 Device Detection (DET)--RO. Indicates the interface device detection and Phy state: Value Description 0h No device detected and Phy communication not established 1h Device presence detected but Phy communication not established 3h Device presence detected and Phy communication established 4h Phy in offline mode as a result of the interface being disabled or running in a BIST loopback mode All other values reserved. 13.4.2.11 PxSCTL--Port [5:0] Serial ATA Control Register (D31:F2) Address Offset: Port 0: ABAR Port 1: ABAR Port 2: ABAR Port 3: ABAR Port 4: ABAR Port 5: ABAR Default Value: 00000004h + + + + + + 12Ch Attribute: R/W, RO 1ACh 22Ch (if port available; see Section 1.3) 2ACh (if port available; see Section 1.3) 32Ch 3ACh Size: 32 bits This is a 32-bit read-write register by which software controls SATA capabilities. Writes to the SControl register result in an action being taken by the PCH or the interface. Reads from the register return the last value written to it. Bit Description 31:20 Reserved 19:16 Port Multiplier Port (PMP)--R/W. This field is not used by AHCI 15:12 Select Power Management (SPM)--R/W. This field is not used by AHCI 11:8 Interface Power Management Transitions Allowed (IPM)--R/W. Indicates which power states the PCH is allowed to transition to: Value Description 0h No interface restrictions 1h Transitions to the PARTIAL state disabled 2h Transitions to the SLUMBER state disabled 3h Transitions to both PARTIAL and SLUMBER states disabled All other values reserved Datasheet 517 SATA Controller Registers (D31:F2) Bit Description 7:4 Speed Allowed (SPD)--R/W. Indicates the highest allowable speed of the interface. This speed is limited by the CAP.ISS (ABAR+00h:bit 23:20) field. Value Description 0h No speed negotiation restrictions 1h Limit speed negotiation to Generation 1 communication rate 2h Limit speed negotiation to Generation 2 communication rate 3h Limit speed negotiation to Generation 3 communication rate The PCH Supports Gen 1 communication rates (1.5 Gb/s), Gen 2 rates (3.0 Gb/s) and Gen 3 rates (6.0 Gb/s) (supported speeds are determined by SKU; see Section 1.3) If software changes SPD after port has been enabled, software is required to perform a port reset using DET=1h. This field shall remain 1h until set to another value by software. 3:0 Device Detection Initialization (DET)--R/W. Controls the PCH's device detection and interface initialization. Value Description 0h No device detection or initialization action requested 1h Perform interface communication initialization sequence to establish communication. This is functionally equivalent to a hard reset and results in the interface being reset and communications re-initialized 4h Disable the Serial ATA interface and put Phy in offline mode All other values reserved. When this field is written to a 1h, the PCH initiates COMRESET and starts the initialization process. When the initialization is complete, this field shall remain 1h until set to another value by software. This field may only be changed to 1h or 4h when PxCMD.ST is 0. Changing this field while the PCH is running results in undefined behavior. Note: It is permissible to implement any of the Serial ATA defined behaviors for transmission of COMRESET when DET=1h. 13.4.2.12 PxSERR--Port [5:0] Serial ATA Error Register (D31:F2) Address Offset: Port 0: ABAR Port 1: ABAR Port 2: ABAR Port 3: ABAR Port 4: ABAR Port 5: ABAR Default Value: 00000000h + + + + + + 130h Attribute: R/WC 1B0h 230h (if port available; see Section 1.3) 2B0h (if port available; see Section 1.3) 330h 3B0h Size: 32 bits Bits 26:16 of this register contain diagnostic error information for use by diagnostic software in validating correct operation or isolating failure modes. Bits 11:0 contain error information used by host software in determining the appropriate response to the error condition. If one or more of bits 11:8 of this register are set, the controller will stop the current transfer. Bit 31:27 518 Description Reserved 26 Exchanged (X)--R/WC. When set to 1, this bit indicates that a change in device presence has been detected since the last time this bit was cleared. This bit shall always be set to 1 anytime a COMINIT signal is received. This bit is reflected in the P0IS.PCS bit. 25 Unrecognized FIS Type (F)--R/WC. Indicates that one or more FISs were received by the Transport layer with good CRC, but had a type field that was not recognized. 24 Transport state transition error (T)--R/WC. Indicates that an error has occurred in the transition from one state to another within the Transport layer since the last time this bit was cleared. Datasheet SATA Controller Registers (D31:F2) Bit Description 23 Link Sequence Error (S): Indicates that one or more Link state machine error conditions was encountered. The Link Layer state machine defines the conditions under which the link layer detects an erroneous transition. 22 Handshake (H)--R/WC. Indicates that one or more R_ERR handshake response was received in response to frame transmission. Such errors may be the result of a CRC error detected by the recipient, a disparity or 8b/10b decoding error, or other error condition leading to a negative handshake on a transmitted frame. 21 CRC Error (C)--R/WC. Indicates that one or more CRC errors occurred with the Link Layer. 20 Disparity Error (D)--R/WC. This field is not used by AHCI. 19 10b to 8b Decode Error (B)--R/WC. Indicates that one or more 10b to 8b decoding errors occurred. 18 Comm Wake (W)--R/WC. Indicates that a Comm Wake signal was detected by the Phy. 17 Phy Internal Error (I)--R/WC. Indicates that the Phy detected some internal error. 16 PhyRdy Change (N)--R/WC. When set to 1, this bit indicates that the internal PhyRdy signal changed state since the last time this bit was cleared. In the PCH, this bit will be set when PhyRdy changes from a 0 -> 1 or a 1 -> 0. The state of this bit is then reflected in the PxIS.PRCS interrupt status bit and an interrupt will be generated if enabled. Software clears this bit by writing a 1 to it. 15:12 Reserved 11 Internal Error (E)--R/WC. The SATA controller failed due to a master or target abort when attempting to access system memory. 10 Protocol Error (P)--R/WC. A violation of the Serial ATA protocol was detected. Note: Persistent Communication or Data Integrity Error (C)--R/WC. A communication error that was not recovered occurred that is expected to be persistent. Persistent communications errors may arise from faulty interconnect with the device, from a device that has been removed or has failed, or a number of other causes. 8 Transient Data Integrity Error (T)--R/WC. A data integrity error occurred that was not recovered by the interface. 7:2 13.4.2.13 The PCH does not set this bit for all protocol violations that may occur on the SATA link. 9 Reserved. 1 Recovered Communications Error (M)--R/WC. Communications between the device and host was temporarily lost but was re-established. This can arise from a device temporarily being removed, from a temporary loss of Phy synchronization, or from other causes and may be derived from the PhyNRdy signal between the Phy and Link layers. 0 Recovered Data Integrity Error (I)--R/WC. A data integrity error occurred that was recovered by the interface through a retry operation or other recovery action. PxSACT--Port [5:0] Serial ATA Active Register (D31:F2) Address Offset: Port 0: ABAR Port 1: ABAR Port 2: ABAR Port 3: ABAR Port 4: ABAR Port 5: ABAR Default Value: 00000000h Bit 31:0 Datasheet + + + + + + 134h Attribute: R/W 1B4h 234h (if port available; see Section 1.3) 2B4h (if port available; see Section 1.3) 334h 3B4h Size: 32 bits Description Device Status (DS)--R/W. System software sets this bit for SATA queuing operations prior to setting the PxCI.CI bit in the same command slot entry. This field is cleared using the Set Device Bits FIS. This field is also cleared when PxCMD.ST (ABAR+118h/198h/218h/298h:bit 0) is cleared by software, and as a result of a COMRESET or SRST. 519 SATA Controller Registers (D31:F2) 13.4.2.14 PxCI--Port [5:0] Command Issue Register (D31:F2) Address Offset: Port 0: ABAR Port 1: ABAR Port 2: ABAR Port 3: ABAR Port 4: ABAR Port 5: ABAR Default Value: 00000000h + + + + + + 138h Attribute: R/W 1B8h 238h (if port available; see Section 1.3) 2B8h (if port available; see Section 1.3) 338h 3B8h Size: 32 bits Bit Description 31:0 Commands Issued (CI)--R/W. This field is set by software to indicate to the PCH that a command has been built-in system memory for a command slot and may be sent to the device. When the PCH receives a FIS which clears the BSY and DRQ bits for the command, it clears the corresponding bit in this register for that command slot. Bits in this field shall only be set to 1 by software when PxCMD.ST is set to 1. This field is also cleared when PxCMD.ST (ABAR+118h/198h/218h/298h:bit 0) is cleared by software. 520 Datasheet SATA Controller Registers (D31:F5) 14 SATA Controller Registers (D31:F5) 14.1 PCI Configuration Registers (SATA-D31:F5) Note: Address locations that are not shown should be treated as Reserved. All of the SATA registers are in the core well. None of the registers can be locked. Table 14-1. SATA Controller PCI Register Address Map (SATA-D31:F5) (Sheet 1 of 2) Offset Datasheet Mnemonic Register Name Default Attribute 00h-01h VID Vendor Identification 8086h RO 02h-03h DID Device Identification See register description RO 04h-05h PCICMD PCI Command 0000h R/W, RO 06h-07h PCISTS PCI Status 02B0h R/WC, RO 08h RID Revision Identification See register description RO 09h PI Programming Interface See register description See register description 0Ah SCC Sub Class Code See register description See register description 0Bh BCC Base Class Code 01h RO 10h-13h PCMD_BAR Primary Command Block Base Address 00000001h R/W, RO 14h-17h PCNL_BAR Primary Control Block Base Address 00000001h R/W, RO 18h-1Bh SCMD_BAR Secondary Command Block Base Address 00000001h R/W, RO 1Ch-1Fh SCNL_BAR Secondary Control Block Base Address 00000001h R/W, RO 20h-23h BAR 24h-27h SIDPBA 2Ch-2Dh SVID 2Eh-2Fh SID Legacy Bus Master Base Address 00000001h R/W, RO Serial ATA Index / Data Pair Base Address 00000000h See register description Subsystem Vendor Identification 0000h R/WO Subsystem Identification 0000h R/WO 34h CAP Capabilities Pointer 80h RO 3Ch INT_LN Interrupt Line 00h R/W 3Dh INT_PN Interrupt Pin See register description RO 40h-41h IDE_TIM Primary IDE Timing 0000h R/W 0000h R/W 00h R/W 42h-43h IDE_TIM Secondary IDE Timing 44h SIDETIM Slave IDE Timing 48h SDMA_CNT Synchronous DMA Control 00h R/W 4Ah-4Bh SDMA_TIM Synchronous DMA Timing 0000h R/W 54h-57h IDE_CONFIG IDE I/O Configuration 00000000h R/W 70h-71h PID PCI Power Management Capability Identification See register description RO 72h-73h PC PCI Power Management Capabilities 4003h RO 74h-75h PMCS PCI Power Management Control and Status 0008h R/W, RO, R/WC 521 SATA Controller Registers (D31:F5) Table 14-1. SATA Controller PCI Register Address Map (SATA-D31:F5) (Sheet 2 of 2) Offset Mnemonic Default Attribute 90h-91h MAP Address Map 0000h R/W 92h-93h PCS Port Control and Status 0000h R/W, RO, R/WC A8h-ABh SATACR0 SATA Capability Register 0 0010B012h RO, R/WO ACh-AFh SATACR1 SATA Capability Register 1 00000048h RO B0h-B1h FLRCID FLR Capability ID 0009h RO B2h-B3h FLRCLV FLR Capability Length and Value 2006h RO B4h-B5h FLRCTRL FLR Control 0000h R/W, RO C0h ATC APM Trapping Control 00h R/W C4h ATS APM Trapping Status 00h R/WC Note: 14.1.1 Register Name The PCH SATA controller is not arbitrated as a PCI device; therefore, it does not need a master latency timer. VID--Vendor Identification Register (SATA--D31:F5) Offset Address: 00h-01h Default Value: 8086h Lockable: No Bit 15:0 14.1.2 Attribute: RO Size: 16 bit Power Well:Core Description Vendor ID--RO. This is a 16-bit value assigned to Intel. Intel VID = 8086h DID--Device Identification Register (SATA--D31:F5) Offset Address: 02h-03h Default Value: See bit description Lockable: No Bit 15:0 Description Device ID--RO. This is a 16-bit value assigned to the PCH SATA controller. Note: 14.1.3 Attribute: RO Size: 16 bit Power Well:Core The value of this field will change dependent upon the value of the MAP Register. See Section 1.3 for the value of the RID Register and Section 14.1.27. PCICMD--PCI Command Register (SATA-D31:F5) Address Offset: 04h-05h Default Value: 0000h Bit 15:11 10 522 Attribute: Size: RO, R/W 16 bits Description Reserved Interrupt Disable--R/W. This disables pin-based INTx# interrupts. This bit has no effect on MSI operation. 0 = Internal INTx# messages are generated if there is an interrupt and MSI is not enabled. 1 = Internal INTx# messages will not be generated. 9 Fast Back to Back Enable (FBE)--RO. Hardwired to 0. 8 SERR# Enable (SERR_EN)--RO. Hardwired to 0. 7 Wait Cycle Control (WCC)--RO. Hardwired to 0. Datasheet SATA Controller Registers (D31:F5) Bit 14.1.4 Description 6 Parity Error Response (PER)--R/W. 0 = Disabled. SATA controller will not generate PERR# when a data parity error is detected. 1 = Enabled. SATA controller will generate PERR# when a data parity error is detected. 5 VGA Palette Snoop (VPS)--RO. Hardwired to 0. 4 Postable Memory Write Enable (PMWE)--RO. Hardwired to 0. 3 Special Cycle Enable (SCE)--RO. Hardwired to 0. 2 Bus Master Enable (BME)--R/W. This bit controls the PCH ability to act as a PCI master for IDE Bus Master transfers. This bit does not impact the generation of completions for split transaction commands. 1 Memory Space Enable (MSE)--RO. This controller does not support AHCI; therefore, no memory space is required. 0 I/O Space Enable (IOSE)--R/W. This bit controls access to the I/O space registers. 0 = Disables access to the Legacy or Native IDE ports (both Primary and Secondary) as well as the Bus Master I/O registers. 1 = Enable. The Base Address register for the Bus Master registers should be programmed before this bit is set. PCISTS--PCI Status Register (SATA-D31:F5) Address Offset: 06h-07h Default Value: 02B0h Note: R/WC, RO 16 bits For the writable bits, software must write a 1 to clear bits that are set. Writing a 0 to the bit has no effect. Bit Description 15 Detected Parity Error (DPE)--R/WC. 0 = No parity error detected by SATA controller. 1 = SATA controller detects a parity error on its interface. 14 Signaled System Error (SSE)--RO. Hardwired to 0. 13 Received Master Abort (RMA)--R/WC. 0 = Master abort Not generated. 1 = SATA controller, as a master, generated a master abort. 12 Reserved 11 Signaled Target Abort (STA)--RO. Hardwired to 0. 10:9 DEVSEL# Timing Status (DEV_STS)--RO. 01 = Hardwired; Controls the device select time for the SATA controller's PCI interface. 8 Data Parity Error Detected (DPED)--R/WC. For PCH, this bit can only be set on read completions received from SiBUS where there is a parity error. 1 = SATA controller, as a master, either detects a parity error or sees the parity error line asserted, and the parity error response bit (bit 6 of the command register) is set. 7 Fast Back to Back Capable (FB2BC)--RO. Hardwired to 1. 6 User Definable Features (UDF)--RO. Hardwired to 0. 5 66MHz Capable (66MHZ_CAP)--RO. Hardwired to 1. 4 Capabilities List (CAP_LIST)--RO. This bit indicates the presence of a capabilities list. The minimum requirement for the capabilities list must be PCI power management for the SATA controller. 3 Interrupt Status (INTS)--RO. Reflects the state of INTx# messages, IRQ14 or IRQ15. 0 = Interrupt is cleared (independent of the state of Interrupt Disable bit in the command register [offset 04h]). 1 = Interrupt is to be asserted 2:0 Datasheet Attribute: Size: Reserved 523 SATA Controller Registers (D31:F5) 14.1.5 RID--Revision Identification Register (SATA--D31:F5) Offset Address: 08h Default Value: See bit description 14.1.6 Attribute: Size: RO 8 bits Bit Description 7:0 Revision ID--RO. This field indicates the device specific revision identifier. See Section 1.3 for the value of the RID Register. PI--Programming Interface Register (SATA-D31:F5) Address Offset: 09h Default Value: 85h Attribute: Size: RO 8 bits When SCC = 01h Bit 7 6:4 14.1.7 Description This read-only bit is a 1 to indicate that the PCH supports bus master operation Reserved 3 Secondary Mode Native Capable (SNC)--RO. Indicates whether or not the secondary channel has a fixed mode of operation. 0 = Indicates the mode is fixed and is determined by the (read-only) value of bit 2. This bit will always return 0. 2 Secondary Mode Native Enable (SNE)--RO. Determines the mode that the secondary channel is operating in. 1 = Secondary controller operating in native PCI mode. This bit will always return 1. 1 Primary Mode Native Capable (PNC)--RO. Indicates whether or not the primary channel has a fixed mode of operation. 0 = Indicates the mode is fixed and is determined by the (read-only) value of bit 0. This bit will always return 0. 0 Primary Mode Native Enable (PNE)--RO. Determines the mode that the primary channel is operating in. 1 = Primary controller operating in native PCI mode. This bit will always return 1. SCC--Sub Class Code Register (SATA-D31:F5) Address Offset: 0Ah Default Value: 01h Bit 7:0 524 Attribute: Size: RO 8 bits Description Sub Class Code (SCC)--RO. The value of this field determines whether the controller supports legacy IDE mode. Datasheet SATA Controller Registers (D31:F5) 14.1.8 BCC--Base Class Code Register (SATA-D31:F5SATA-D31:F5) Address Offset: 0Bh Default Value: 01h Bit 7:0 14.1.9 Attribute: Size: Description Base Class Code (BCC)--RO. 01h = Mass storage device PCMD_BAR--Primary Command Block Base Address Register (SATA-D31:F5) Address Offset: 10h-13h Default Value: 00000001h Bit 31:16 15:3 2:1 0 Note: 14.1.10 Attribute: Size: R/W, RO 32 bits Description Reserved Base Address--R/W. This field provides the base address of the I/O space (8 consecutive I/O locations). Reserved Resource Type Indicator (RTE)--RO. Hardwired to 1 to indicate a request for I/O space. This 8-byte I/O space is used in native mode for the Primary Controller's Command Block. PCNL_BAR--Primary Control Block Base Address Register (SATA-D31:F5) Address Offset: 14h-17h Default Value: 00000001h Bit 31:16 15:2 Attribute: Size: R/W, RO 32 bits Description Reserved Base Address--R/W. This field provides the base address of the I/O space (4 consecutive I/O locations). 1 Reserved 0 Resource Type Indicator (RTE)--RO. Hardwired to 1 to indicate a request for I/O space. Note: Datasheet RO 8 bits This 4-byte I/O space is used in native mode for the Primary Controller's Command Block. 525 SATA Controller Registers (D31:F5) 14.1.11 SCMD_BAR--Secondary Command Block Base Address Register (SATA D31:F5) Address Offset: 18h-1Bh Default Value: 00000001h Bit 31:16 15:3 2:1 0 Note: 14.1.12 Attribute: Size: Description Reserved Base Address--R/W. This field provides the base address of the I/O space (8 consecutive I/O locations). Reserved Resource Type Indicator (RTE)--RO. Hardwired to 1 to indicate a request for I/O space. This 8-byte I/O space is used in native mode for the Secondary Controller's Command Block. SCNL_BAR--Secondary Control Block Base Address Register (SATA D31:F5) Address Offset: 1Ch-1Fh Default Value: 00000001h Bit 31:16 15:2 Attribute: Size: R/W, RO 32 bits Description Reserved Base Address--R/W. This field provides the base address of the I/O space (4 consecutive I/O locations). 1 Reserved 0 Resource Type Indicator (RTE)--RO. Hardwired to 1 to indicate a request for I/O space. Note: 14.1.13 R/W, RO 32 bits This 4-byte I/O space is used in native mode for the Secondary Controller's Command Block. BAR--Legacy Bus Master Base Address Register (SATA-D31:F5) Address Offset: 20h-23h Default Value: 00000001h Attribute: Size: R/W, RO 32 bits The Bus Master IDE interface function uses Base Address register 5 to request a 16byte I/O space to provide a software interface to the Bus Master functions. Only 12 bytes are actually used (6 bytes for primary, 6 bytes for secondary). Only bits [15:4] are used to decode the address. Bit 31:16 15:5 4 3:1 0 526 Description Reserved Base Address--R/W. This field provides the base address of the I/O space (16 consecutive I/O locations). Base Address 4 (BA4)--R/W. When SCC is 01h, this bit will be R/W resulting in requesting 16B of I/O space. Reserved Resource Type Indicator (RTE)--RO. Hardwired to 1 to indicate a request for I/O space. Datasheet SATA Controller Registers (D31:F5) 14.1.14 SIDPBA--SATA Index/Data Pair Base Address Register (SATA-D31:F5) Address Offset: 24h-27h Default Value: 00000000h Attribute: Size: R/W, RO 32 bits When SCC is 01h When the programming interface is IDE, the register represents an I/O BAR allocating 16B of I/O space for the I/O mapped registers defined in Section 14.3. While 16B of locations are allocated, some maybe reserved. Bit 31:16 15:4 3:1 0 14.1.15 Description Reserved Base Address (BA)--R/W. Base address of register I/O space Reserved Resource Type Indicator (RTE)--RO. Hardwired to 1 to indicate a request for I/O space. SVID--Subsystem Vendor Identification Register (SATA-D31:F5) Address Offset: 2Ch-2Dh Default Value: 0000h Lockable: No Function Level Reset:No 14.1.16 Attribute: R/WO Size: 16 bits Power Well:Core Bit Description 15:0 Subsystem Vendor ID (SVID)--R/WO. Value is written by BIOS. No hardware action taken on this value. SID--Subsystem Identification Register (SATA-D31:F5) Address Offset: 2Eh-2Fh Default Value: 0000h Lockable: No Bit 15:0 14.1.17 Attribute: R/WO Size: 16 bits Power Well:Core Description Subsystem ID (SID)--R/WO. Value is written by BIOS. No hardware action taken on this value. CAP--Capabilities Pointer Register (SATA-D31:F5) Address Offset: 34h Default Value: 70h Datasheet Attribute: Size: RO 8 bits Bit Description 7:0 Capabilities Pointer (CAP_PTR)--RO. Indicates that the first capability pointer offset is 70h if the Sub Class Code (SCC) (Dev 31:F2:0Ah) is configure as IDE mode (value of 01). 527 SATA Controller Registers (D31:F5) 14.1.18 INT_LN--Interrupt Line Register (SATA-D31:F5) Address Offset: 3Ch Default Value: 00h Function Level Reset: No Bit 7:0 14.1.19 Attribute: Size: Description Interrupt Line--R/W. This field is used to communicate to software the interrupt line that the interrupt pin is connected to. These bits are not reset by FLR. INT_PN--Interrupt Pin Register (SATA-D31:F5) Address Offset: 3Dh Default Value: See Register Description Bit 7:0 14.1.20 R/W 8 bits Attribute: Size: RO 8 bits Description Interrupt Pin--RO. This reflects the value of D31IP.SIP1 (Chipset Config Registers:Offset 3100h:bits 11:8). IDE_TIM--IDE Timing Register (SATA-D31:F5) Address Offset: Primary: 40h-41h Attribute: R/W Secondary: 42h-43h Default Value: 0000h Size: 16 bits Bits 14:12 and 9:0 of this register are R/W to maintain software compatibility. These bits have no effect on hardware. Bit 15 IDE Decode Enable (IDE)--R/W. Individually enable/disable the Primary or Secondary decode. 0 = Disable. 1 = Enables the PCH to decode the associated Command Block and Control Block. 14:12 IDE_TIM Field 2--R/W. This field is R/W to maintain software compatibility. This field has no effect on hardware. 11:10 Reserved 9:0 14.1.21 Description IDE_TIM Field 1--R/W. This field is R/W to maintain software compatibility. This field has no effect on hardware. SDMA_CNT--Synchronous DMA Control Register (SATA-D31:F5) Address Offset: 48h Default Value: 00h Note: R/W 8 bits This register is R/W to maintain software compatibility. These bits have no effect on hardware. Bit 7:3 528 Attribute: Size: Description Reserved 2 Secondary Master ATAxx Enable (SDAE0)--R/W. 0 = Disable (default) 1 = Enable DMA timing modes for the secondary master device. 1 Reserved Datasheet SATA Controller Registers (D31:F5) Bit 0 14.1.22 Description Primary Master ATAxx Enable (PDAE0)--R/W. 0 = Disable (default) 1 = Enable DMA timing modes for the primary master device SDMA_TIM--Synchronous DMA Timing Register (SATA-D31:F5) Address Offset: 4Ah-4Bh Default Value: 0000h Note: 15:10 Description Reserved 9:8 SDMA_TIM Field 2--R/W. This field is R/W to maintain software compatibility. This field has no effect on hardware. 7:2 Reserved 1:0 SDMA_TIM Field 1--R/W. This field is R/W to maintain software compatibility. This field has no effect on hardware. IDE_CONFIG--IDE I/O Configuration Register (SATA-D31:F5) Address Offset: 54h-57h Default Value: 00000000h Note: Attribute: Size: R/W 32 bits This register is R/W to maintain software compatibility. These bits have no effect on hardware. Bit Description 31:24 Reserved 23:16 IDE_CONFIG Field 6--R/W. This field is R/W to maintain software compatibility. This field has no effect on hardware. 15 Reserved 14 IDE_CONFIG Field 5--R/W. This field is R/W to maintain software compatibility. This field has no effect on hardware. 13 Reserved 12 IDE_CONFIG Field 4--R/W. This field is R/W to maintain software compatibility. This field has no effect on hardware. 11:8 7:4 Datasheet R/W 16 bits This register is R/W to maintain software compatibility. These bits have no effect on hardware. Bit 14.1.23 Attribute: Size: Reserved IDE_CONFIG Field 3--R/W. This field is R/W to maintain software compatibility. This field has no effect on hardware. 3 Reserved 2 IDE_CONFIG Field 2--R/W. This field is R/W to maintain software compatibility. This field has no effect on hardware. 1 Reserved 0 IDE_CONFIG Field 1--R/W. This field is R/W to maintain software compatibility. This field has no effect on hardware. 529 SATA Controller Registers (D31:F5) 14.1.24 PID--PCI Power Management Capability Identification Register (SATA-D31:F5) Address Offset: 70h-71h Default Value: B001h Bits 15:8 7:0 14.1.25 Attribute: Size: Description Next Capability (NEXT)--RO. When SCC is 01h, this field will be B0h indicating the next item is FLR Capability Pointer in the list. Capability ID (CID)--RO. Indicates that this pointer is a PCI power management. PC--PCI Power Management Capabilities Register (SATA-D31:F5) Address Offset: 72h-73h Default Value: 4003h Bits 15:11 Attribute: Size: RO 16 bits Description PME Support (PME_SUP)--RO. By default with SCC = 01h, the default value of 00000 indicates no PME support in IDE mode. 10 D2 Support (D2_SUP)--RO. Hardwired to 0. The D2 state is not supported 9 D1 Support (D1_SUP)--RO. Hardwired to 0. The D1 state is not supported 8:6 Auxiliary Current (AUX_CUR)--RO. PME# from D3COLD state is not supported, therefore this field is 000b. 5 Device Specific Initialization (DSI)--RO. Hardwired to 0 to indicate that no device-specific initialization is required. 4 Reserved 3 PME Clock (PME_CLK)--RO. Hardwired to 0 to indicate that PCI clock is not required to generate PME#. 2:0 14.1.26 RO 16 bits Version (VER)--RO. Hardwired to 011 to indicates support for Revision 1.2 of the PCI Power Management Specification. PMCS--PCI Power Management Control and Status Register (SATA-D31:F5) Address Offset: 74h-75h Default Value: 0008h Function Level Reset:No (Bits 8 and 15 only) Bits 15 Attribute: Size: RO, R/W, R/WC 16 bits Description PME Status (PMES)--R/WC. Bit is set when a PME event is to be requested, and if this bit and PMEE is set, a PME# will be generated from the SATA controller. Note: When SCC=01h this bit will be RO 0. Software is advised to clear PMEE together with PMES prior to changing SCC through MAP.SMS. This bit is not reset by Function Level Reset. 14:9 8 Reserved PME Enable (PMEE)--R/W. When SCC is not 01h, this bit R/W. When set, the SATA controller generates PME# form D3HOT on a wake event. Note: When SCC=01h, this bit will be RO 0. Software is advised to clear PMEE together with PMES prior to changing SCC through MAP.SMS. This bit is not reset by Function Level Reset. 530 Datasheet SATA Controller Registers (D31:F5) Bits 7:4 3 2 1:0 14.1.27 Description Reserved No Soft Reset (NSFRST)--RO. These bits are used to indicate whether devices transitioning from D3HOT state to D0 state will perform an internal reset. 0 = Device transitioning from D3HOT state to D0 state perform an internal reset. 1 = Device transitioning from D3HOT state to D0 state do not perform an internal reset. Configuration content is preserved. Upon transition from the D3HOT state to D0 state initialized state, no additional operating system intervention is required to preserve configuration context beyond writing to the PowerState bits. Regardless of this bit, the controller transition from D3HOT state to D0 state by a system or bus segment reset will return to the state D0 uninitialized with only PME context preserved if PME is supported and enabled. Reserved Power State (PS)--R/W. These bits are used both to determine the current power state of the SATA controller and to set a new power state. 00 = D0 state 11 = D3HOT state When in the D3HOT state, the controller's configuration space is available, but the I/O and memory spaces are not. Additionally, interrupts are blocked. MAP--Address Map Register (SATA-D31:F5) Address Offset: 90h-91h Default Value: 0000h Function Level Reset: No (Bits 9:8 only) Bits 15:8 Datasheet Attribute: Size: R/W, R/WO, RO bits Description Reserved 7:6 SATA Mode Select (SMS)--R/W. Software programs these bits to control the mode in which the SATA Controller should operate. 00b = IDE Mode All other combinations are reserved. 5:2 Reserved 1:0 Map Value (MV)--Reserved. 531 SATA Controller Registers (D31:F5) 14.1.28 PCS--Port Control and Status Register (SATA-D31:F5) Address Offset: 92h-93h Default Value: 0000h Function Level Reset: No Attribute: Size: R/W, RO 16 bits By default, the SATA ports are set to the disabled state (bits [5:0] = 0). When enabled by software, the ports can transition between the on, partial, and slumber states and can detect devices. When disabled, the port is in the "off" state and cannot detect any devices. If an AHCI-aware or RAID enabled operating system is being booted, then system BIOS shall insure that all supported SATA ports are enabled prior to passing control to the OS. Once the AHCI aware OS is booted, it becomes the enabling/disabling policy owner for the individual SATA ports. This is accomplished by manipulating a port PxSCTL and PxCMD fields. Because an AHCI or RAID aware OS will typically not have knowledge of the PxE bits and because the PxE bits act as master on/off switches for the ports, preboot software must insure that these bits are set to 1 prior to booting the OS, regardless as to whether or not a device is currently on the port. Bits 15:10 Reserved 9 Port 5 Present (P5P)--RO. The status of this bit may change at any time. This bit is cleared when the port is disabled using P1E. This bit is not cleared upon surprise removal of a device. 0 = No device detected. 1 = The presence of a device on Port 1 has been detected. 8 Port 4 Present (P4P)--RO. The status of this bit may change at any time. This bit is cleared when the port is disabled using P0E. This bit is not cleared upon surprise removal of a device. 0 = No device detected. 1 = The presence of a device on Port 0 has been detected. 7:2 14.1.29 Description Reserved 1 Port 5 Enabled (P5E)--R/W. 0 = Disabled. The port is in the `off' state and cannot detect any devices. 1 = Enabled. The port can transition between the on, partial, and slumber states and can detect devices. This bit is read-only 0 when MAP.SPD[1]= 1 pr is a PCIe Port. 0 Port 4 Enabled (P4E)--R/W. 0 = Disabled. The port is in the `off' state and cannot detect any devices. 1 = Enabled. The port can transition between the on, partial, and slumber states and can detect devices. This bit is read-only 0 when MAP.SPD[0]= 1 or is a PCIe Port. SATACR0--SATA Capability Register 0 (SATA-D31:F5) Address Offset: A8h-ABh Default Value: 0010B012h Function Level Reset: No (Bits 15:8 only) Attribute: Size: RO, R/WO 32 bits When SCC is 01h, this register is read-only 0. Bit 532 Description 31:24 Reserved 23:20 Major Revision (MAJREV)--RO. Major revision number of the SATA Capability Pointer implemented. 19:16 Minor Revision (MINREV)--RO. Minor revision number of the SATA Capability Pointer implemented. Datasheet SATA Controller Registers (D31:F5) Bit 15:8 7:0 14.1.30 Description Next Capability Pointer (NEXT)--R/WO. Points to the next capability structure. Capability ID (CAP)--RO. The value of 12h has been assigned by the PCI SIG to designate the SATA capability pointer. SATACR1--SATA Capability Register 1 (SATA-D31:F5) Address Offset: ACh-AFh Default Value: 00000048h Attribute: Size: RO 32 bits When SCC is 01h, this register is read-only 0. Bit 31:16 14.1.31 Description Reserved 15:4 BAR Offset (BAROFST)--RO. Indicates the offset into the BAR where the index/Data pair are located (in DWord granularity). The index and Data I/O registers are located at offset 10h within the I/O space defined by LBAR (BAR4). A value of 004h indicates offset 10h. 3:0 BAR Location (BARLOC)--RO. Indicates the absolute PCI Configuration Register address of the BAR containing the Index/Data pair (in DWord granularity). The Index and Data I/O registers reside within the space defined by LBAR (BAR4) in the SATA controller. a value of 8h indicates and offset of 20h, which is LBAR (BAR4). FLRCID--FLR Capability ID Register (SATA-D31:F5) Address Offset: B0h-B1h Default Value: 0009h Bit 15:8 7:0 14.1.32 Attribute: Size: RO 16 bits Description Next Capability Pointer--RO. A value of 00h indicates the final item in the Capability List. Capability ID--RO. The value of this field depends on the FLRCSSECL bit. If FLRCSSEL = 0, this field is 13h If FLRCSSEL = 1, this field is 00h. FLRCLV--FLR Capability Length and Value Register (SATA-D31:F5) Address Offset: B2h-B3h Default Value: 2006h Function Level Reset:No (Bits 9:8 only) Attribute: Size: RO, R/WO 16 bits When FLRCSSEL = 0, this register is RO. Bit 15:10 Reserved 9 FLR Capability--R/WO. This field indicates support for Function Level Reset. 8 TXP Capability--R/WO. This field indicates support for the Transactions Pending (TXP) bit. TXP must be supported if FLR is supported. 7:0 Datasheet Description Capability Length--RO. This field indicates the number of bytes of the Vendor Specific capability as required by the PCI specification. It has the value of 06h for FLR Capability. 533 SATA Controller Registers (D31:F5) 14.1.33 FLRCTRL--FLR Control Register (SATA-D31:F5) Address Offset: B4h-B5h Default Value: 0000h Bit 15:9 8 7:1 0 14.1.34 Attribute: Size: Description Reserved Transactions Pending (TXP)--RO. 0 = Completions for all Non-Posted requests have been received by the controller. 1 = Controller has issued Non-Posted request which has not been completed. Reserved Initiate FLR--R/W. Used to initiate FLR transition. A write of 1 indicates FLR transition. ATC--APM Trapping Control Register (SATA-D31:F5) Address Offset: C0h Default Value: 00h Note: Attribute: Size: 7:0 Description Reserved ATC--APM Trapping Control Register (SATA-D31:F5) Address Offset: C4h Default Value: 00h Note: Attribute: Size: R/WC 8 bits This SATA controller does not support legacy I/O access. Therefore, this register is reserved. Software shall not change the default values of the register; otherwise the result will be undefined. Bit 7:0 14.2 R/W 8 bits This SATA controller does not support legacy I/O access. Therefore, this register is reserved. Software shall not change the default values of the register; otherwise, the result will be undefined. Bit 14.1.35 R/W, RO 16 bits Description Reserved Bus Master IDE I/O Registers (D31:F5) The bus master IDE function uses 16 bytes of I/O space, allocated using the BAR register, located in D31:F2 Configuration space, offset 20h. All bus master IDE I/O space registers can be accessed as byte, word, or DWord quantities. Reading reserved bits returns an indeterminate, inconsistent value, and writes to reserved bits have no affect (but should not be attempted). These registers are only used for legacy operation. Software must not use these registers when running AHCI. The description of the I/O registers is shown in Table 14-1. Table 14-1. Bus Master IDE I/O Register Address Map (Sheet 1 of 2) 534 BAR+ Offset Mnemonic 00 BMICP 01 -- Register Command Register Primary Reserved Default Attribute 00h R/W -- RO Datasheet SATA Controller Registers (D31:F5) Table 14-1. Bus Master IDE I/O Register Address Map (Sheet 2 of 2) 14.2.1 BAR+ Offset Mnemonic 02 BMISP 03 -- Register Bus Master IDE Status Register Primary Reserved 04-07 BMIDP Bus Master IDE Descriptor Table Pointer Primary 08 BMICS Command Register Secondary 09 -- 0Ah BMISS 0Bh -- 0Ch-0Fh BMIDS Reserved Bus Master IDE Status Register Secondary Reserved Bus Master IDE Descriptor Table Pointer Secondary Attribute 00h R/W, R/WC, RO -- RO xxxxxxxxh R/W 00h R/W -- RO 00h R/W, R/WC, RO -- RO xxxxxxxxh R/W BMIC[P,S]--Bus Master IDE Command Register (D31:F5) Address Offset: Primary: BAR + 00h Secondary: BAR + 08h Default Value: 00h Bit 7:4 3 2:1 0 Attribute: R/W Size: 8 bits Description Reserved Read / Write Control (R/WC)--R/W. This bit sets the direction of the bus master transfer: This bit must NOT be changed when the bus master function is active. 0 = Memory reads 1 = Memory writes Reserved Start/Stop Bus Master (START)--R/W. 0 = All state information is lost when this bit is cleared. Master mode operation cannot be stopped and then resumed. If this bit is reset while bus master operation is still active (that is, the Bus Master IDE Active bit (D31:F5:BAR + 02h, bit 0) of the Bus Master IDE Status register for that IDE channel is set) and the drive has not yet finished its data transfer (the Interrupt bit in the Bus Master IDE Status register for that IDE channel is not set), the bus master command is said to be aborted and data transferred from the drive may be discarded instead of being written to system memory. 1 = Enables bus master operation of the controller. Bus master operation does not actually start unless the Bus Master Enable bit (D31:F5:04h, bit 2) in PCI configuration space is also set. Bus master operation begins when this bit is detected changing from 0 to 1. The controller will transfer data between the IDE device and memory only when this bit is set. Master operation can be halted by writing a 0 to this bit. Note: Datasheet Default This bit is intended to be cleared by software after the data transfer is completed, as indicated by either the Bus Master IDE Active bit being cleared or the Interrupt bit of the Bus Master IDE Status register for that IDE channel being set, or both. Hardware does not clear this bit automatically. If this bit is cleared to 0 prior to the DMA data transfer being initiated by the drive in a device to memory data transfer, then the PCH will not send DMAT to terminate the data transfer. SW intervention (such as, sending SRST) is required to reset the interface in this condition. 535 SATA Controller Registers (D31:F5) 14.2.2 BMIS[P,S]--Bus Master IDE Status Register (D31:F5) Address Offset: Primary: BAR + 02h Secondary: BAR + 0Ah Default Value: 00h Bit 7 Size: 8 bits Description PRD Interrupt Status (PRDIS)--R/WC. 0 = Software clears this bit by writing a 1 to it. 1 = This bit is set when the host controller execution of a PRD that has its PRD_INT bit set. Reserved 5 Drive 0 DMA Capable--R/W. 0 = Not Capable 1 = Capable. Set by device dependent code (BIOS or device driver) to indicate that drive 0 for this channel is capable of DMA transfers, and that the controller has been initialized for optimum performance. The PCH does not use this bit. It is intended for systems that do not attach BMIDE to the PCI bus. Reserved 2 Interrupt--R/WC. 0 = Software clears this bit by writing a 1 to it. 1 = Set when a device FIS is received with the `I' bit set, provided that software has not disabled interrupts using the IEN bit of the Device Control Register (see chapter 5 of the Serial ATA Specification, Revision 1.0a). 1 Error--R/WC. 0 = Software clears this bit by writing a 1 to it. 1 = This bit is set when the controller encounters a target abort or master abort when transferring data on PCI. 0 Bus Master IDE Active (ACT)--RO. 0 = This bit is cleared by the PCH when the last transfer for a region is performed, where EOT for that region is set in the region descriptor. It is also cleared by the PCH when the Start Bus Master bit (D31:F5:BAR+ 00h, bit 0) is cleared in the Command register. When this bit is read as a 0, all data transferred from the drive during the previous bus master command is visible in system memory, unless the bus master command was aborted. 1 = Set by the PCH when the Start bit is written to the Command register. BMID[P,S]--Bus Master IDE Descriptor Table Pointer Register (D31:F5) Address Offset: Primary: BAR + 04h-07h Secondary: BAR + 0Ch-0Fh Default Value: All bits undefined Attribute: R/W Size: 32 bits Bit Description 31:2 Address of Descriptor Table (ADDR)--R/W. The bits in this field correspond to bits [31:2] of the memory location of the Physical Region Descriptor (PRD). The Descriptor Table must be DWordaligned. The Descriptor Table must not cross a 64-K boundary in memory. 1:0 536 R/W, R/WC, RO 6 4:3 14.2.3 Attribute: Reserved Datasheet SATA Controller Registers (D31:F5) 14.3 Serial ATA Index/Data Pair Superset Registers All of these I/O registers are in the core well. They are exposed only when SCC is 01h (that is, IDE programming interface) and the controller is not in combined mode. These are Index/Data Pair registers that are used to access the SerialATA superset registers (SerialATA Status, SerialATA Control and SerialATA Error). The I/O space for these registers is allocated through SIDPBA. Locations with offset from 08h to 0Fh are reserved for future expansion. Software-write operations to the reserved locations shall have no effect while software-read operations to the reserved locations shall return 0. 14.3.1 SINDX--SATA Index Register (D31:F5) Address Offset: SIDPBA + 00h Default Value: 00000000h Note: 31:16 15:8 7:0 Description Reserved Port Index (PIDX)--R/W. This Index field is used to specify the port of the SATA controller at which the port-specific SSTS, SCTL, and SERR registers are located. 00h = Primary Master (Port 4) 02h = Secondary Master (Port 5) All other values are Reserved. Register Index (RIDX)--R/W. This Index field is used to specify one out of three registers currently being indexed into. 00h = SSTS 01h = SCTL 02h = SERR All other values are Reserved. SDATA--SATA Index Data Register (D31:F5) Address Offset: SIDPBA + 04h Default Value: All bits undefined Note: Datasheet R/W 32 bits These are Index/Data Pair Registers that are used to access the SSTS, SCTL, and SERR. The I/O space for these registers is allocated through SIDPBA. Bit 14.3.2 Attribute: Size: Attribute: Size: R/W 32 bits These are Index/Data Pair Registers that are used to access the SSTS, SCTL, and SERR. The I/O space for these registers is allocated through SIDPBA. Bit Description 31:0 Data (DATA)--R/W. This Data register is a "window" through which data is read or written to the memory mapped registers. A read or write to this Data register triggers a corresponding read or write to the memory mapped register pointed to by the Index register. The Index register must be setup prior to the read or write to this Data register. A physical register is not actually implemented as the data is actually stored in the memory mapped registers. Since this is not a physical register, the "default" value is the same as the default value of the register pointed to by Index. 537 SATA Controller Registers (D31:F5) 14.3.2.1 PxSSTS--Serial ATA Status Register (D31:F5) Address Offset: Default Value: 00000000h Attribute: Size: RO 32 bits SDATA when SINDX.RIDX is 00h. This is a 32-bit register that conveys the current state of the interface and host. The PCH updates it continuously and asynchronously. When the PCH transmits a COMRESET to the device, this register is updated to its reset values. Bit 31:12 11:8 Description Reserved Interface Power Management (IPM)--RO. Indicates the current interface state: Value 0h Description Device not present or communication not established 1h Interface in active state 2h Interface in PARTIAL power management state 6h Interface in SLUMBER power management state All other values reserved. 7:4 Current Interface Speed (SPD)--RO. Indicates the negotiated interface communication speed. Value Description 0h Device not present or communication not established 1h Generation 1 communication rate negotiated 2h Generation 2 communication rate negotiated 3h Generation 3 communication rate negotiated All other values reserved. The PCH Supports Gen 1 communication rates (1.5 Gb/s), Gen 2 rates (3.0 Gb/s) and Gen 3 rates (6.0 Gb/s). 3:0 Device Detection (DET)--RO. Indicates the interface device detection and Phy state: Value Description 0h No device detected and Phy communication not established 1h Device presence detected but Phy communication not established 3h Device presence detected and Phy communication established 4h Phy in offline mode as a result of the interface being disabled or running in a BIST loopback mode All other values reserved. 538 Datasheet SATA Controller Registers (D31:F5) 14.3.2.2 PxSCTL--Serial ATA Control Register (D31:F5) Address Offset: Default Value: 00000004h Attribute: Size: R/W, RO 32 bits SDATA when SINDX.RIDX is 01h. This is a 32-bit read-write register by which software controls SATA capabilities. Writes to the SControl register result in an action being taken by the PCH or the interface. Reads from the register return the last value written to it. Bit Description 31:20 Reserved 19:16 Port Multiplier Port (PMP)--RO. This field is not used by AHCI. 15:12 Select Power Management (SPM)--RO. This field is not used by AHCI. 11:8 Interface Power Management Transitions Allowed (IPM)--R/W. Indicates which power states the PCH is allowed to transition to: Value Description 0h No interface restrictions 1h Transitions to the PARTIAL state disabled 2h Transitions to the SLUMBER state disabled 3h Transitions to both PARTIAL and SLUMBER states disabled All other values reserved 7:4 Speed Allowed (SPD)--R/W. Indicates the highest allowable speed of the interface. This speed is limited by the CAP.ISS (ABAR+00h:bit 23:20) field. Value Description 0h No speed negotiation restrictions 1h Limit speed negotiation to Generation 1 communication rate 2h Limit speed negotiation to Generation 2 communication rate 3h Limit speed negotiation to Generation 3 communication rate All other values reserved. The PCH Supports Gen 1 communication rates (1.5 Gb/s), Gen 2 rates (3.0 Gb/s) and Gen 3 rates (6 Gb/s). 3:0 Device Detection Initialization (DET)--R/W. Controls the PCH's device detection and interface initialization. Value Description 0h No device detection or initialization action requested 1h Perform interface communication initialization sequence to establish communication. This is functionally equivalent to a hard reset and results in the interface being reset and communications re-initialized 4h Disable the Serial ATA interface and put Phy in offline mode All other values reserved. Datasheet 539 SATA Controller Registers (D31:F5) 14.3.2.3 PxSERR--Serial ATA Error Register (D31:F5) Address Offset: Default Value: 00000000h Attribute: Size: R/WC 32 bits SDATA when SINDx.RIDX is 02h. Bits 26:16 of this register contains diagnostic error information for use by diagnostic software in validating correct operation or isolating failure modes. Bits 11:0 contain error information used by host software in determining the appropriate response to the error condition. If one or more of bits 11:8 of this register are set, the controller will stop the current transfer. Bit 31:27 Description Reserved 26 Exchanged (X)--R/WC. When set to 1, this bit indicates that a change in device presence has been detected since the last time this bit was cleared. This bit shall always be set to 1 anytime a COMINIT signal is received. This bit is reflected in the P0IS.PCS bit. 25 Unrecognized FIS Type (F)--R/WC. Indicates that one or more FISs were received by the Transport layer with good CRC, but had a type field that was not recognized. 24 Transport state transition error (T)--R/WC. Indicates that an error has occurred in the transition from one state to another within the Transport layer since the last time this bit was cleared. 23 Link Sequence Error (S): Indicates that one or more Link state machine error conditions was encountered. The Link Layer state machine defines the conditions under which the link layer detects an erroneous transition. 22 Handshake (H)--R/WC. Indicates that one or more R_ERR handshake response was received in response to frame transmission. Such errors may be the result of a CRC error detected by the recipient, a disparity or 8b/10b decoding error, or other error condition leading to a negative handshake on a transmitted frame. 21 CRC Error (C)--R/WC. Indicates that one or more CRC errors occurred with the Link Layer. 20 Disparity Error (D)--R/WC. This field is not used by AHCI. 19 10b to 8b Decode Error (B)--R/WC. Indicates that one or more 10b to 8b decoding errors occurred. 18 Comm Wake (W)--R/WC. Indicates that a Comm Wake signal was detected by the Phy. 17 Phy Internal Error (I)--R/WC. Indicates that the Phy detected some internal error. 16 PhyRdy Change (N)--R/WC. When set to 1, this bit indicates that the internal PhyRdy signal changed state since the last time this bit was cleared. In the PCH, this bit will be set when PhyRdy changes from a 0 -> 1 or a 1 -> 0. The state of this bit is then reflected in the PxIS.PRCS interrupt status bit and an interrupt will be generated if enabled. Software clears this bit by writing a 1 to it. 15:12 Reserved 11 Internal Error (E)--R/WC. The SATA controller failed due to a master or target abort when attempting to access system memory. 10 Protocol Error (P)--R/WC. A violation of the Serial ATA protocol was detected. Note: The PCH does not set this bit for all protocol violations that may occur on the SATA link. 9 Persistent Communication or Data Integrity Error (C)--R/WC. A communication error that was not recovered occurred that is expected to be persistent. Persistent communications errors may arise from faulty interconnect with the device, from a device that has been removed or has failed, or a number of other causes. 8 Transient Data Integrity Error (T)--R/WC. A data integrity error occurred that was not recovered by the interface. 7:2 Reserved 1 Recovered Communications Error (M)--R/WC. Communications between the device and host was temporarily lost but was re-established. This can arise from a device temporarily being removed, from a temporary loss of Phy synchronization, or from other causes and may be derived from the PhyNRdy signal between the Phy and Link layers. 0 Recovered Data Integrity Error (I)--R/WC. A data integrity error occurred that was recovered by the interface through a retry operation or other recovery action. 540 Datasheet EHCI Controller Registers (D29:F0, D26:F0) 15 EHCI Controller Registers (D29:F0, D26:F0) 15.1 USB EHCI Configuration Registers (USB EHCI--D29:F0, D26:F0) Note: Prior to BIOS initialization of the PCH USB subsystem, the EHCI controllers will appear as Function 7. After BIOS initialization, the EHCI controllers will be Function 0. Note: Register address locations that are not shown in Table 15-1 should be treated as Reserved (see Section 9.2 for details). Table 15-1. USB EHCI PCI Register Address Map (USB EHCI--D29:F0, D26:F0) (Sheet 1 of 2) Datasheet Offset Mnemonic Default Value Attribute 00h-01h VID Vendor Identification Register Name 8086h RO 02h-03h DID Device Identification See register description RO 04h-05h PCICMD PCI Command 0000h R/W, RO 06h-07h PCISTS PCI Status 0290h R/W, RO 08h RID See register description RO Revision Identification 09h PI Programming Interface 20h RO 0Ah SCC Sub Class Code 03h RO 0Bh BCC Base Class Code 0Ch RO 0Dh PMLT Primary Master Latency Timer 00h RO 0Eh HEADTYP 10h-13h MEM_BASE 2Ch-2Dh SVID 2Eh-2Fh SID Header Type 00h RO 00000000h R/W, RO USB EHCI Subsystem Vendor Identification XXXXh R/W USB EHCI Subsystem Identification XXXXh R/W Memory Base Address 34h CAP_PTR Capabilities Pointer 50h RO 3Ch INT_LN Interrupt Line 00h R/W 3Dh INT_PN Interrupt Pin See register description RO 50h PWR_CAPID 01h RO 58h R/W PCI Power Management Capability ID 51h NXT_PTR1 Next Item Pointer 52h-53h PWR_CAP Power Management Capabilities C9C2h R/W 54h-55h PWR_CNTL_STS Power Management Control / Status 0000h R/W, R/WC, RO 58h DEBUG_CAPID 0Ah RO 98h RWS 20A0h RO Debug Port Capability ID 59h NXT_PTR2 5Ah-5Bh DEBUG_BASE Next Item Pointer #2 Debug Port Base Offset 60h USB_RELNUM USB Release Number 20h RO 61h FL_ADJ Frame Length Adjustment 20h R/W, RO 62h-63h PWAKE_CAP 64h PDO Port Wake Capabilities 07FFh R/W, RO Port Disable Override Register 0000h R/W, RO 541 EHCI Controller Registers (D29:F0, D26:F0) Table 15-1. USB EHCI PCI Register Address Map (USB EHCI--D29:F0, D26:F0) (Sheet 2 of 2) Offset Mnemonic Register Name RMH Device Removable Field Register Default Value Attribute 66h RMHDEVR 0000h R/W, RO 68h-6Bh LEG_EXT_CAP USB EHCI Legacy Support Extended Capability 00000001h R/W, RO 6Ch-6Fh LEG_EXT_CS USB EHCI Legacy Extended Support Control/Status 00000000h R/W, R/WC, RO 70h-73h SPECIAL_SMI Intel Specific USB 2.0 SMI 00000000h R/W, R/WC 74h-77h OCMAP Over-Current Mapping C0300C03h R/W 78h-7Dh -- 7Eh-7Fh RMHWKCTL Reserved RMH Wake Control -- -- 0000h R/W, RO 80h ACCESS_CNTL Access Control 00h R/W, RO 84h-87h EHCIIR1 EHCI Initialization Register 1 01h R/W 98h FLR_CID FLR Capability ID 13h RO 99h FLR_NEXT FLR Next Capability Pointer 00h RO 9Ch FLR_CTRL FLR Control 00h R/W, RO 9Dh FLR_STS FLR Status 00h RO Note: All configuration registers in this section are in the core well and reset by a core well reset and the D3-to-D0 warm reset, except as noted. 15.1.1 VID--Vendor Identification Register (USB EHCI--D29:F0, D26:F0) Offset Address: 00h-01h Default Value: 8086h Bit 15:0 15.1.2 Attribute: Size: RO 16 bits Vendor ID--RO. This is a 16-bit value assigned to Intel. DID--Device Identification Register (USB EHCI--D29:F0, D26:F0) Bit Description 15:0 Device ID--RO. This is a 16-bit value assigned to the PCH USB EHCI controller. See Section 1.3 for the value of the DID Register. PCICMD--PCI Command Register (USB EHCI--D29:F0, D26:F0) Address Offset: 04h-05h Default Value: 0000h Bit 15:11 542 RO 16 bits Description Offset Address: 02h-03h Default Value: See bit description 15.1.3 Attribute: Size: Attribute: Size: R/W, RO 16 bits Description Reserved Read Only Datasheet EHCI Controller Registers (D29:F0, D26:F0) Bit Description 10 Interrupt Disable--R/W. 0 = The function is capable of generating interrupts. 1 = The function can not generate its interrupt to the interrupt controller. The corresponding Interrupt Status bit (D29:F0, D26:F0:06h, bit 3) is not affected by the interrupt enable. 9 Fast Back to Back Enable (FBE)--RO. Hardwired to 0. 8 SERR# Enable (SERR_EN)--R/W. 0 = Disables EHC's capability to generate an SERR#. 1 = The Enhanced Host controller (EHC) is capable of generating (internally) SERR# in the following cases: *When it receive a completion status other than "successful" for one of its DMA initiated memory reads on DMI (and subsequently on its internal interface). *When it detects an address or command parity error and the Parity Error Response bit is set. *When it detects a data parity error (when the data is going into the EHC) and the Parity Error Response bit is set. 7 Wait Cycle Control (WCC)--RO. Hardwired to 0. 6 Parity Error Response (PER)--R/W. 0 = The EHC is not checking for correct parity (on its internal interface). 1 = The EHC is checking for correct parity (on its internal interface) and halt operation when bad parity is detected during the data phase. Note: If the EHC detects bad parity on the address or command phases when the bit is set to 1, the host controller does not take the cycle. It halts the host controller (if currently not halted) and sets the Host System Error bit in the USBSTS register. This applies to both requests and completions from the system interface. This bit must be set in order for the parity errors to generate SERR#. 15.1.4 5 VGA Palette Snoop (VPS)--RO. Hardwired to 0. 4 Postable Memory Write Enable (PMWE)--RO. Hardwired to 0. 3 Special Cycle Enable (SCE)--RO. Hardwired to 0. 2 Bus Master Enable (BME)--R/W. 0 = Disables this functionality. 1 = Enables the PCH to act as a master on the PCI bus for USB transfers. 1 Memory Space Enable (MSE)--R/W. This bit controls access to the USB 2.0 Memory Space registers. 0 = Disables this functionality. 1 = Enables accesses to the USB 2.0 registers. The Base Address register (D29:F0, D26:F0:10h) for USB 2.0 should be programmed before this bit is set. 0 I/O Space Enable (IOSE)--RO. Hardwired to 0. PCISTS--PCI Status Register (USB EHCI--D29:F0, D26:F0) Address Offset: 06h-07h Default Value: 0290h Note: R/WC, RO 16 bits For the writable bits, software must write a 1 to clear bits that are set. Writing a 0 to the bit has no effect. Bit 15 Datasheet Attribute: Size: Description Detected Parity Error (DPE)--R/WC. 0 = No parity error detected. 1 = This bit is set by the PCH when a parity error is seen by the EHCI controller, regardless of the setting of bit 6 or bit 8 in the Command register or any other conditions. 543 EHCI Controller Registers (D29:F0, D26:F0) Bit 14 Signaled System Error (SSE)--R/WC. 0 = No SERR# signaled by the PCH. 1 = This bit is set by the PCH when it signals SERR# (internally). The SER_EN bit (bit 8 of the Command Register) must be 1 for this bit to be set. 13 Received Master Abort (RMA)--R/WC. 0 = No master abort received by EHC on a memory access. 1 = This bit is set when EHC, as a master, receives a master abort status on a memory access. This is treated as a Host Error and halts the DMA engines. This event can optionally generate an SERR# by setting the SERR# Enable bit. 12 Received Target Abort (RTA)--R/WC. 0 = No target abort received by EHC on memory access. 1 = This bit is set when EHC, as a master, receives a target abort status on a memory access. This is treated as a Host Error and halts the DMA engines. This event can optionally generate an SERR# by setting the SERR# Enable bit (D29:F0, D26:F0:04h, bit 8). 11 Signaled Target Abort (STA)--RO. This bit is used to indicate when the EHCI function responds to a cycle with a target abort. There is no reason for this to happen, so this bit is hardwired to 0. 10:9 DEVSEL# Timing Status (DEVT_STS)--RO. This 2-bit field defines the timing for DEVSEL# assertion. Read Only 8 Master Data Parity Error Detected (DPED)--R/WC. 0 = No data parity error detected on USB 2.0 read completion packet. 1 = This bit is set by the PCH when a data parity error is detected on a USB 2.0 read completion packet on the internal interface to the EHCI host controller and bit 6 of the Command register is set to 1. 7 Fast Back to Back Capable (FB2BC)--RO. Hardwired to 1. 6 User Definable Features (UDF)--RO. Hardwired to 0. 5 66 MHz Capable (66 MHz _CAP)--RO. Hardwired to 0. 4 Capabilities List (CAP_LIST)--RO. Hardwired to 1 indicating that offset 34h contains a valid capabilities pointer. 3 Interrupt Status--RO. This bit reflects the state of this function's interrupt at the input of the enable/disable logic. 0 = This bit will be 0 when the interrupt is de-asserted. 1 = This bit is a 1 when the interrupt is asserted. The value reported in this bit is independent of the value in the Interrupt Enable bit. 2:0 15.1.5 Description Reserved RID--Revision Identification Register (USB EHCI--D29:F0, D26:F0) Offset Address: 08h Default Value: See bit description Bit 7:0 544 Attribute: Size: RO 8 bits Description Revision ID--RO. This field indicates the device specific revision identifier. See Section 1.3 for the value of the RID Register. Datasheet EHCI Controller Registers (D29:F0, D26:F0) 15.1.6 PI--Programming Interface Register (USB EHCI--D29:F0, D26:F0) Address Offset: 09h Default Value: 20h 15.1.7 Attribute: Size: Bit Description 7:0 Programming Interface--RO. A value of 20h indicates that this USB 2.0 host controller conforms to the EHCI Specification. SCC--Sub Class Code Register (USB EHCI--D29:F0, D26:F0) Address Offset: 0Ah Default Value: 03h Bit 7:0 15.1.8 Attribute: Size: RO 8 bits BCC--Base Class Code Register (USB EHCI--D29:F0, D26:F0) 7:0 Description Base Class Code (BCC)--RO. 0Ch = Serial bus controller. PMLT--Primary Master Latency Timer Register (USB EHCI--D29:F0, D26:F0) Address Offset: 0Dh Default Value: 00h Bit 7:0 Attribute: Size: RO 8 bits Description Master Latency Timer Count (MLTC)--RO. Hardwired to 00h. Because the EHCI controller is internally implemented with arbitration on an interface (and not PCI), it does not need a master latency timer. HEADTYP--Header Type Register (USB EHCI--D29:F0, D26:F0) Address Offset: 0Eh Default Value: 00h Bit 7 6:0 Datasheet RO 8 bits Sub Class Code (SCC)--RO. 03h = Universal serial bus host controller. Bit 15.1.10 Attribute: Size: Description Address Offset: 0Bh Default Value: 0Ch 15.1.9 RO 8 bits Attribute: Size: RO 8 bits Description Multi-Function Device--RO. When set to `1' indicates this is a multifunction device: 0 = Single-function device 1 = Multi-function device. Configuration Layout. Hardwired to 00h, which indicates the standard PCI configuration layout. 545 EHCI Controller Registers (D29:F0, D26:F0) 15.1.11 MEM_BASE--Memory Base Address Register (USB EHCI--D29:F0, D26:F0) Address Offset: 10h-13h Default Value: 00000000h Bit 31:10 9:4 3 2:1 0 15.1.12 Attribute: Size: Description Base Address--R/W. Bits [31:10] correspond to memory address signals [31:10], respectively. This gives 1-KB of locatable memory space aligned to 1-KB boundaries. Reserved Prefetchable--RO. Hardwired to 0 indicating that this range should not be prefetched. Type--RO. Hardwired to 00b indicating that this range can be mapped anywhere within 32-bit address space. Resource Type Indicator (RTE)--RO. Hardwired to 0 indicating that the base address field in this register maps to memory space. SVID--USB EHCI Subsystem Vendor ID Register (USB EHCI--D29:F0, D26:F0) Address Offset: 2Ch-2Dh Default Value: XXXXh Reset: None Attribute: R/W Size: 16 bits Power Well:Core Bit Description 15:0 Subsystem Vendor ID (SVID)--R/W. This register, in combination with the USB 2.0 Subsystem ID register, enables the operating system to distinguish each subsystem from the others. Note: 15.1.13 Writes to this register are enabled when the WRT_RDONLY bit (D29:F0, D26:F0:80h, bit 0) is set to 1. SID--USB EHCI Subsystem ID Register (USB EHCI--D29:F0, D26:F0) Address Offset: 2Eh-2Fh Default Value: XXXXh Reset: None Attribute: R/W Size: 16 bits Power Well:Core Bit Description 15:0 Subsystem ID (SID)--R/W. BIOS sets the value in this register to identify the Subsystem ID. This register, in combination with the Subsystem Vendor ID register, enables the operating system to distinguish each subsystem from other(s). Note: 546 R/W, RO 32 bits Writes to this register are enabled when the WRT_RDONLY bit (D29:F0, D26:F0:80h, bit 0) is set to 1. Datasheet EHCI Controller Registers (D29:F0, D26:F0) 15.1.14 CAP_PTR--Capabilities Pointer Register (USB EHCI--D29:F0, D26:F0) Address Offset: 34h Default Value: 50h Power Well: Core Bit 7:0 15.1.15 Attribute: Size: Description Capabilities Pointer (CAP_PTR)--RO. This register points to the starting offset of the USB 2.0 capabilities ranges. INT_LN--Interrupt Line Register (USB EHCI--D29:F0, D26:F0) Address Offset: 3Ch Default Value: 00h Reset: No Bit 7:0 15.1.16 Attribute: R/W Size: 8 bits Power Well:Core Description Interrupt Line (INT_LN)--R/W. This data is not used by the PCH. It is used as a scratchpad register to communicate to software the interrupt line that the interrupt pin is connected to. INT_PN--Interrupt Pin Register (USB EHCI--D29:F0, D26:F0) Address Offset: 3Dh Default Value: See Description 15.1.17 Attribute: Size: RO 8 bits Bit Description 7:0 Interrupt Pin--RO. This reflects the value of D29IP.E1IP (Chipset Config Registers:Offset 3108:bits 3:0) or D26IP.E2IP (Chipset Config Registers:Offset 3114:bits 3:0). Note: As a single function device, only INTA# may be used while the other three interrupt lines have no meaning. (refer to PCI 3.0 specification, Section 2.2.6, Interrupt Pins). Note: Bits 7:4 are always 0h PWR_CAPID--PCI Power Management Capability Identification Register (USB EHCI--D29:F0, D26:F0) Address Offset: 50h Default Value: 01h Bit 7:0 Datasheet RO 8 bits Attribute: Size: RO 8 bits Description Power Management Capability ID--RO. A value of 01h indicates that this is a PCI Power Management capabilities field. 547 EHCI Controller Registers (D29:F0, D26:F0) 15.1.18 NXT_PTR1--Next Item Pointer #1 Register (USB EHCI--D29:F0, D26:F0) Address Offset: 51h Default Value: 58h Power Well: Core 15.1.19 Attribute: Size: R/W 8 bits Bit Description 7:0 Next Item Pointer 1 Value--R/W (special). This register defaults to 58h that indicates that the next capability registers begin at configuration offset 58h. This register is writable when the WRT_RDONLY bit (D29:F0, D26:F0:80h, bit 0) is set. This allows BIOS to effectively hide the Debug Port capability registers, if necessary. This register should only be written during system initialization before the plug-and-play software has enabled any master-initiated traffic. Only values of 58h (Debug Port and FLR capabilities visible) and 98h (Debug Port invisible, next capability is FLR) are expected to be programmed in this register. Note: Register not reset by D3-to-D0 warm reset. PWR_CAP--Power Management Capabilities Register (USB EHCI--D29:F0, D26:F0) Address Offset: 52h-53h Default Value: C9C2h Power Well: Core Attribute: Size: R/W, RO 16 bits Bit Description 15:11 PME Support (PME_SUP)--R/W. This 5-bit field indicates the power states in which the function may assert PME#. The PCH EHC does not support the D1 or D2 states. For all other states, the PCH EHC is capable of generating PME#. Software should never need to modify this field. 10 D2 Support (D2_SUP)--RO. 0 = D2 State is not supported 9 D1 Support (D1_SUP)--RO. 0 = D1 State is not supported 8:6 5 Auxiliary Current (AUX_CUR)--R/W. The PCH EHC reports 375 mA maximum suspend well current required when in the D3COLD state. Device Specific Initialization (DSI)--RO. The PCH reports 0, indicating that no device-specific initialization is required. 4 Reserved 3 PME Clock (PME_CLK)--RO. The PCH reports 0, indicating that no PCI clock is required to generate PME#. 2:0 Version (VER)--RO. The PCH reports 010b, indicating that it complies with Revision 1.1 of the PCI Power Management Specification. Notes: 1. Normally, this register is read-only to report capabilities to the power management software. To report different power management capabilities, depending on the system in which the PCH is used, bits 15:11 and 8:6 in this register are writable when the WRT_RDONLY bit (D29:F0, D26:F0:80h, bit 0) is set. The value written to this register does not affect the hardware other than changing the value returned during a read. 2. Reset: core well, but not D3-to-D0 warm reset. 548 Datasheet EHCI Controller Registers (D29:F0, D26:F0) 15.1.20 PWR_CNTL_STS--Power Management Control / Status Register (USB EHCI--D29:F0, D26:F0) Address Offset: 54h-55h Default Value: 0000h Power Well Bits 1,0:Core; Power Well Bits 15,8: Bit 15 Attribute: Size: Suspend R/W, R/WC, RO 16 bits Description PME Status--R/WC. 0 = Writing a 1 to this bit will clear it and cause the internal PME to de-assert (if enabled). 1 = This bit is set when the PCH EHC would normally assert the PME# signal independent of the state of the PME_En bit. Note: This bit must be explicitly cleared by the operating system each time the operating system is loaded. This bit is not reset by Function Level Reset. 14:13 12:9 Data Select--RO. Hardwired to 0000b indicating it does not support the associated Data register. 8 PME Enable--R/W. 0 = Disable. 1 = Enables the PCH EHC to generate an internal PME signal when PME_Status is 1. Note: This bit must be explicitly cleared by the operating system each time it is initially loaded. This bit is not reset by Function Level Reset. 7:2 Reserved 1:0 Power State--R/W. This 2-bit field is used both to determine the current power state of EHC function and to set a new power state. The definition of the field values are: 00 = D0 state 11 = D3HOT state If software attempts to write a value of 10b or 01b in to this field, the write operation must complete normally; however, the data is discarded and no state change occurs. When in the D3HOT state, the PCH must not accept accesses to the EHC memory range; but the configuration space must still be accessible. When not in the D0 state, the generation of the interrupt output is blocked. Specifically, the PIRQH is not asserted by the PCH when not in the D0 state. When software changes this value from the D3HOT state to the D0 state, an internal warm (soft) reset is generated, and software must re-initialize the function. Note: 15.1.21 Data Scale--RO. Hardwired to 00b indicating it does not support the associated Data register. Reset (bits 15, 8): suspend well, and not D3-to-D0 warm reset nor core well reset. DEBUG_CAPID--Debug Port Capability ID Register (USB EHCI--D29:F0, D26:F0) Address Offset: 58h Default Value: 0Ah Bit 7:0 Datasheet Attribute: Size: RO 8 bits Description Debug Port Capability ID--RO. Hardwired to 0Ah indicating that this is the start of a Debug Port Capability structure. 549 EHCI Controller Registers (D29:F0, D26:F0) 15.1.22 NXT_PTR2--Next Item Pointer #2 Register (USB EHCI--D29:F0, D26:F0) Address Offset: 59h Default Value: 98h Function Level Reset: No Bit 7:0 15.1.23 Attribute: Size: Description Next Item Pointer 2 Capability--RO. This register points to the next capability in the Function Level Reset capability structure. DEBUG_BASE--Debug Port Base Offset Register (USB EHCI--D29:F0, D26:F0) Address Offset: 5Ah-5Bh Default Value: 20A0h Attribute: Size: Description 15:13 BAR Number--RO. Hardwired to 001b to indicate the memory BAR begins at offset 10h in the EHCI configuration space. Debug Port Offset--RO. Hardwired to 0A0h to indicate that the Debug Port registers begin at offset A0h in the EHCI memory range. USB_RELNUM--USB Release Number Register (USB EHCI--D29:F0, D26:F0) Address Offset: 60h Default Value: 20h Bit 7:0 550 RO 16 bits Bit 12:0 15.1.24 RO 8 bits Attribute: Size: RO 8 bits Description USB Release Number--RO. A value of 20h indicates that this controller follows Universal Serial Bus (USB) Specification, Revision 2.0. Datasheet EHCI Controller Registers (D29:F0, D26:F0) 15.1.25 FL_ADJ--Frame Length Adjustment Register (USB EHCI--D29:F0, D26:F0) Address Offset: 61h Default Value: 20h Function Level Reset: No Attribute: R/W Size: 8 bits Power Well:Suspend This feature is used to adjust any offset from the clock source that generates the clock that drives the SOF counter. When a new value is written into these six bits, the length of the frame is adjusted. Its initial programmed value is system dependent based on the accuracy of hardware USB clock and is initialized by system BIOS. This register should only be modified when the HChalted bit (D29:F0, D26:F0:CAPLENGTH + 24h, bit 12) in the USB 2.0_STS register is a 1. Changing value of this register while the host controller is operating yields undefined results. It should not be reprogrammed by USB system software unless the default or BIOS programmed values are incorrect, or the system is restoring the register while returning from a suspended state. These bits in suspend well and not reset by a D3-to-D0 warm rest or a core well reset. Bit Datasheet Description 7:6 Reserved--RO. These bits are reserved for future use and should read as 00b. 5:0 Frame Length Timing Value--R/W. Each decimal value change to this register corresponds to 16 high-speed bit times. The SOF cycle time (number of SOF counter clock periods to generate a SOF micro-frame length) is equal to 59488 + value in this field. The default value is decimal 32 (20h) that gives a SOF cycle time of 60000. Frame Length (# 480 MHz Clocks) (decimal) Frame Length Timing Value (this register) (decimal) 59488 0 59504 1 59520 2 -- -- 59984 31 60000 32 -- -- 60480 62 60496 63 551 EHCI Controller Registers (D29:F0, D26:F0) 15.1.26 PWAKE_CAP--Port Wake Capability Register (USB EHCI--D29:F0, D26:F0) Address Offset: 62-63h Default Value: 07FFh Function Level Reset: No Attribute: R/W, RO Size: 16 bits Power Well:Suspend This register is in the suspend power well. The intended use of this register is to establish a policy about which ports are to be used for wake events. Bit positions 1- 8(D29) or 1-6(D26) in the mask correspond to a physical port implemented on the current EHCI controller. A 1 in a bit position indicates that a device connected below the port can be enabled as a wake-up device and the port may be enabled for disconnect/ connect or overcurrent events as wake-up events. This is an information-only mask register. The bits in this register do not affect the actual operation of the EHCI host controller. The system-specific policy can be established by BIOS initializing this register to a system-specific value. System software uses the information in this register when enabling devices and ports for remote wake-up. These bits are not reset by a D3-to-D0 warm rest or a core well reset. s Bit 15:11 10:1 (D29) 0 15.1.27 Description Reserved, Read Only Port Wake Up Capability Mask--R/W. Bit positions 1-10 correspond to a physical port implemented on this host controller. For example, bit position 1 corresponds to port 1, bit position 2 corresponds to port 2, and so on. Port Wake Implemented--R/W. A 1 in this bit indicates that this register is implemented to software. PDO--Port Disable Override Register Address Offset: 64h Default Value: 0000h Power Well: Suspend Bit 15:8 7:0 552 Attribute: Size: R/W, RO 16 bits Description Reserved, Read Only USB Port Disable: A `1' in a bit position prevents the corresponding USB port from reporting a Device Connection to the hub. Attempts to enable the port will be ignored by the hardware when this bit is 1. For EHCI 2, bit 7 and 6 are reserved. Writing to these bits has no significance. This register cannot be written when the USB Per-Port Registers Write Enable bit (in Power Management I/O Space) is 0. Datasheet EHCI Controller Registers (D29:F0, D26:F0) 15.1.28 RMHDEVR--RMH Device Removable Field Register Address Offset: 66h Default Value: 0000h Power Well: Suspend Bit 15:9 8:1 0 15.1.29 Attribute: Size: Description Reserved, Read Only Device Removable Bit Map: A `1' in a given bit position in this field indicates that the corresponding downstream port of the RMH is connected to a non-removable device. A `0' indicates that the port is exposed to the user. Bits 8:1 are mapped to Ports 8:1 (on EHCI #1, Device. 29) Bits 6:1 are mapped to Ports 6:1 (on EHCI #2, Device. 26) This bits control the value returned by the RMH in the DeviceRemovable field of the Hub Descriptor. A `1' in a given bit position in this register will result in the corresponding bit in the DeviceRemovable field of the hub descriptor being set to `1' as well (indicating that the port is connected to a non-removable device). System BIOS is expected to set these values upon Boot and resume from Sx states. Note: Bits 8:7 are reserved (maintained as RW but with no significance) for EHCI2 (Device 26) since RMH#2 corresponding to EHCI2 has only 6 ports. Reserved, Read Only LEG_EXT_CAP--USB EHCI Legacy Support Extended Capability Register (USB EHCI--D29:F0, D26:F0) Address Offset: 68-6Bh Default Value: 00000001h Power Well: Suspend Function Level Reset: No Note: Attribute: Size: R/W, RO 32 bits These bits are not reset by a D3-to-D0 warm rest or a core well reset. Bit 31:25 24 23:17 16 Datasheet R/W, RO 16 bits Description Reserved--RO. Hardwired to 00h HC OS Owned Semaphore--R/W. System software sets this bit to request ownership of the EHCI controller. Ownership is obtained when this bit reads as 1 and the HC BIOS Owned Semaphore bit reads as clear. Reserved--RO. Hardwired to 00h HC BIOS Owned Semaphore--R/W. The BIOS sets this bit to establish ownership of the EHCI controller. System BIOS will clear this bit in response to a request for ownership of the EHCI controller by system software. 15:8 Next EHCI Capability Pointer--RO. Hardwired to 00h to indicate that there are no EHCI Extended Capability structures in this device. 7:0 Capability ID--RO. Hardwired to 01h to indicate that this EHCI Extended Capability is the Legacy Support Capability. 553 EHCI Controller Registers (D29:F0, D26:F0) 15.1.30 LEG_EXT_CS--USB EHCI Legacy Support Extended Control / Status Register (USB EHCI--D29:F0, D26:F0) Address Offset: 6C-6Fh Default Value: 00000000h Power Well: Suspend Function Level Reset: No Note: R/W, R/WC, RO 32 bits These bits are not reset by a D3-to-D0 warm rest or a core well reset. Bit Description 31 SMI on BAR--R/WC. Software clears this bit by writing a 1 to it. 0 = Base Address Register (BAR) not written. 1 = This bit is set to 1 when the Base Address Register (BAR) is written. 30 SMI on PCI Command--R/WC. Software clears this bit by writing a 1 to it. 0 = PCI Command (PCICMD) Register Not written. 1 = This bit is set to 1 when the PCI Command (PCICMD) Register is written. 29 SMI on OS Ownership Change--R/WC. Software clears this bit by writing a 1 to it. 0 = No HC OS Owned Semaphore bit change. 1 = This bit is set to 1 when the HC OS Owned Semaphore bit in the LEG_EXT_CAP register (D29:F0, D26:F0:68h, bit 24) transitions from 1 to 0 or 0 to 1. 28:22 21 Reserved SMI on Async Advance--RO. This bit is a shadow bit of the Interrupt on Async Advance bit (D29:F0, D26:F0:CAPLENGTH + 24h, bit 5) in the USB 2.0_STS register. Note: 20 19 To clear this bit system software must write a 1 to the Port Change Detect bit in the USB2.0_STS register. SMI on USB Error--RO. This bit is a shadow bit of USB Error Interrupt (USBERRINT) bit (D29:F0, D26:F0:CAPLENGTH + 24h, bit 1) in the USB2.0_STS register. Note: 16 To clear this bit system software must write a 1 to the Frame List Rollover bit in the USB2.0_STS register. SMI on Port Change Detect--RO. This bit is a shadow bit of Port Change Detect bit (D29:F0, D26:F0:CAPLENGTH + 24h, bit 2) in the USB2.0_STS register. Note: 17 To clear this bit system software must write a 1 to the Host System Error bit in the USB2.0_STS register. SMI on Frame List Rollover--RO. This bit is a shadow bit of Frame List Rollover bit (D29:F0, D26:F0:CAPLENGTH + 24h, bit 3) in the USB2.0_STS register. Note: 18 To clear this bit system software must write a 1 to the Interrupt on Async Advance bit in the USB 2.0_STS register. SMI on Host System Error--RO. This bit is a shadow bit of Host System Error bit in the USB2.0_STS register (D29:F0, D26:F0:CAPLENGTH + 24h, bit 4). Note: To clear this bit system software must write a 1 to the USB Error Interrupt bit in the USB2.0_STS register. SMI on USB Complete--RO. This bit is a shadow bit of USB Interrupt (USBINT) bit (D29:F0, D26:F0:CAPLENGTH + 24h, bit 0) in the USB2.0_STS register. Note: 554 Attribute: Size: To clear this bit system software must write a 1 to the USB Interrupt bit in the USB2.0_STS register. 15 SMI on BAR Enable--R/W. 0 = Disable. 1 = Enable. When this bit is 1 and SMI on BAR (D29:F0, D26:F0:6Ch, bit 31) is 1, then the host controller will issue an SMI. 14 SMI on PCI Command Enable--R/W. 0 = Disable. 1 = Enable. When this bit is 1 and SMI on PCI Command (D29:F0, D26:F0:6Ch, bit 30) is 1, then the host controller will issue an SMI. Datasheet EHCI Controller Registers (D29:F0, D26:F0) Bit Description 13 SMI on OS Ownership Enable--R/W. 0 = Disable. 1 = Enable. When this bit is a 1 AND the OS Ownership Change bit (D29:F0, D26:F0:6Ch, bit 29) is 1, the host controller will issue an SMI. 12:6 15.1.31 Reserved 5 SMI on Async Advance Enable--R/W. 0 = Disable. 1 = Enable. When this bit is a 1, and the SMI on Async Advance bit (D29:F0, D26:F0:6Ch, bit 21) is a 1, the host controller will issue an SMI immediately. 4 SMI on Host System Error Enable--R/W. 0 = Disable. 1 = Enable. When this bit is a 1, and the SMI on Host System Error (D29:F0, D26:F0:6Ch, bit 20) is a 1, the host controller will issue an SMI. 3 SMI on Frame List Rollover Enable--R/W. 0 = Disable. 1 = Enable. When this bit is a 1, and the SMI on Frame List Rollover bit (D29:F0, D26:F0:6Ch, bit 19) is a 1, the host controller will issue an SMI. 2 SMI on Port Change Enable--R/W. 0 = Disable. 1 = Enable. When this bit is a 1, and the SMI on Port Change Detect bit (D29:F0, D26:F0:6Ch, bit 18) is a 1, the host controller will issue an SMI. 1 SMI on USB Error Enable--R/W. 0 = Disable. 1 = Enable. When this bit is a 1, and the SMI on USB Error bit (D29:F0, D26:F0:6Ch, bit 17) is a 1, the host controller will issue an SMI immediately. 0 SMI on USB Complete Enable--R/W. 0 = Disable. 1 = Enable. When this bit is a 1, and the SMI on USB Complete bit (D29:F0, D26:F0:6Ch, bit 16) is a 1, the host controller will issue an SMI immediately. SPECIAL_SMI--Intel(R) Specific USB 2.0 SMI Register (USB EHCI--D29:F0, D26:F0) Address Offset: 70h-73h Default Value: 00000000h Power Well: Suspend Function Level Reset: No Note: R/W, R/WC 32 bits These bits are not reset by a D3-to-D0 warm rest or a core well reset. Bit Datasheet Attribute: Size: Description 31:25 Reserved 24:22 SMI on PortOwner--R/WC. Software clears these bits by writing a 1 to it. 0 = No Port Owner bit change. 1 = Bits 24:22 correspond to the Port Owner bits for ports 0 (22) through 3 (24). These bits are set to 1 when the associated Port Owner bits transition from 0 to 1 or 1 to 0. 21 SMI on PMCSR--R/WC. Software clears these bits by writing a 1 to it. 0 = Power State bits Not modified. 1 = Software modified the Power State bits in the Power Management Control/Status (PMCSR) register (D29:F0, D26:F0:54h). 20 SMI on Async--R/WC. Software clears these bits by writing a 1 to it. 0 = No Async Schedule Enable bit change 1 = Async Schedule Enable bit transitioned from 1 to 0 or 0 to 1. 555 EHCI Controller Registers (D29:F0, D26:F0) Bit 556 Description 19 SMI on Periodic--R/WC. Software clears this bit by writing a 1 it. 0 = No Periodic Schedule Enable bit change. 1 = Periodic Schedule Enable bit transitions from 1 to 0 or 0 to 1. 18 SMI on CF--R/WC. Software clears this bit by writing a 1 it. 0 = No Configure Flag (CF) change. 1 = Configure Flag (CF) transitions from 1 to 0 or 0 to 1. 17 SMI on HCHalted--R/WC. Software clears this bit by writing a 1 it. 0 = HCHalted did Not transition to 1 (as a result of the Run/Stop bit being cleared). 1 = HCHalted transitions to 1 (as a result of the Run/Stop bit being cleared). 16 SMI on HCReset--R/WC. Software clears this bit by writing a 1 it. 0 = HCRESET did Not transitioned to 1. 1 = HCRESET transitioned to 1. 15:6 SMI on PortOwner Enable--R/W. 0 = Disable. 1 = Enable. When any of these bits are 1 and the corresponding SMI on PortOwner bits are 1, then the host controller will issue an SMI. Unused ports should have their corresponding bits cleared. 5 SMI on PMSCR Enable--R/W. 0 = Disable. 1 = Enable. When this bit is 1 and SMI on PMSCR is 1, then the host controller will issue an SMI. 4 SMI on Async Enable--R/W. 0 = Disable. 1 = Enable. When this bit is 1 and SMI on Async is 1, then the host controller will issue an SMI 3 SMI on Periodic Enable--R/W. 0 = Disable. 1 = Enable. When this bit is 1 and SMI on Periodic is 1, then the host controller will issue an SMI. 2 SMI on CF Enable--R/W. 0 = Disable. 1 = Enable. When this bit is 1 and SMI on CF is 1, then the host controller will issue an SMI. 1 SMI on HCHalted Enable--R/W. 0 = Disable. 1 = Enable. When this bit is a 1 and SMI on HCHalted is 1, then the host controller will issue an SMI. 0 SMI on HCReset Enable--R/W. 0 = Disable. 1 = Enable. When this bit is a 1 and SMI on HCReset is 1, then host controller will issue an SMI. Datasheet EHCI Controller Registers (D29:F0, D26:F0) 15.1.32 OCMAP--Over-Current Mapping Register Address Offset: 74-77h Default Value: C0300C03h Function Level Reset: No Attribute: R/W Size: 32 bits Power well: Suspend Bit Description 31:24 OC3/OC7 Mapping Each bit position maps OC3 (EHCI 1) and OC7 (EHCI2) to a set of ports as follows: EHCI 1: Map OC3 Bit: 31 Port: 7 30 29 28 27 26 25 24 6 5 4 3 2 1 0 EHCI 2: Map OC7 Bit: 31 30 29 28 27 26 25 24 Port: Rsvd Rsvd 13 12 11 10 9 8 It is software responsibility to ensure that a given port`s bit map is set only for one OC pin. 23:16 OC2/OC6 Mapping Each bit position maps OC2 (EHCI 1) and OC6 (EHCI2) to a set of ports as follows: EHCI 1: Map OC2 Bit: 23 Port: 7 22 21 20 19 18 17 16 6 5 4 3 2 1 0 EHCI 2: Map OC6 Bit: 23 22 21 20 19 18 17 16 Port: Rsvd Rsvd 13 12 11 10 9 8 It is software responsibility to ensure that a given port`s bit map is set only for one OC pin. 15:08 OC1/OC5 Mapping Each bit position maps OC1 (EHCI 1) and OC5 (EHCI2) to a set of ports as follows: EHCI 1: Map OC1 Bit: 15 Port: 7 14 13 12 11 10 9 8 6 5 4 3 2 1 0 EHCI 2: Map OC5 Bit: 15 14 13 12 11 10 9 8 Port: Rsvd Rsvd 13 12 11 10 9 8 It is software responsibility to ensure that a given port`s bit map is set only for one OC pin. 07:00 OC0/OC4 Mapping Each bit position maps OC0 (EHCI 1) and OC4 (EHCI2) to a set of ports as follows: EHCI 1: Map OC0 Bit: Port: 7 7 6 6 5 4 3 2 1 0 5 4 3 2 1 0 EHCI 2: Map OC4 Bit: 7 6 5 4 3 2 1 0 Port: Rsvd Rsvd 13 12 11 10 9 8 It is software responsibility to ensure that a given port`s bit map is set only for one OC pin. Datasheet 557 EHCI Controller Registers (D29:F0, D26:F0) 15.1.33 RMHWKCTL--RMH Wake Control Register Address Offset: 7Eh Default Value: 0000h Function Level Reset: No Bit 15:09 08 07:04 15.1.34 Attribute: R/W, RO Size: 16 bits Power well: Suspend Description Reserved RMH Inherit EHCI Wake Control Settings -R/W. 0 = bits 2:0 of this register DO NOT reflect the appropriate bits of EHCI PORTSC0 bits 22:20. 1 = Bits 2:0 of this register reflect the appropriate bits of EHCI PORTSC0 bits 22:20. Reserved 03 RMH Upstream Wake on Device Resume Disable- R/W 0 = The RMH will initiate a resume on its upstream port and cause a wake when a device resume occurs on an enabled downstream port 1 = The RMH will NOT initiate a resume on its upstream port and cause a wake when a device resume occurs on an enabled downstream port 02 RMH Upstream Wake on OC Disable - R/W 0 = The RMH will initiate a resume on its upstream port and cause a wake when overcurrent condition occurs downstream port 1 = The RMH will NOT initiate a resume on its upstream port and cause a wake when overcurrent condition occurs downstream port 01 RMH Upstream Wake on Disconnect Disable - R/W 0 = The RMH will initiate a resume on its upstream port and cause a wake when a disconnect event occurs on a downstream port 1 = The RMH will NOT initiate a resume on its upstream port and cause a wake when a disconnect event occurs on a downstream port 00 RMH Upstream Wake on Connect Disable- R/W 0 = The RMH will initiate a resume on its upstream port and cause a wake when a connect event occurs on a downstream port 1 = The RMH will NOT initiate a resume on its upstream port and cause a wake when a connect event occurs on a downstream port ACCESS_CNTL--Access Control Register (USB EHCI--D29:F0, D26:F0) Address Offset: 80h Default Value: 00h Function Level Reset: No Bit 7:1 0 558 Attribute: Size: R/W 8 bits Description Reserved WRT_RDONLY--R/W. When set to 1, this bit enables a select group of normally read-only registers in the EHC function to be written by software. Registers that may only be written when this mode is entered are noted in the summary tables and detailed description as "Read/Write-Special". The registers fall into two categories: 1. System-configured parameters 2. Status bits Datasheet EHCI Controller Registers (D29:F0, D26:F0) 15.1.35 EHCIIR1--EHCI Initialization Register 1 (USB EHCI--D29:F0, D26:F0) Address Offset: 84h Default Value: 01h Power well: Core Bit 31:29 28 Attribute: Size: R/W 32 bits Description Reserved EHCI Prefetch Entry Clear--R/W. 0 = EHC will clear prefetched entries in DMA. 1 = EHC will not clear prefetched entries in DMA 27:5 4 3:0 15.1.36 Reserved Intel(R) Prefetch Based Pause Enable--R/W. 0 = Intel Prefetch Based Pause is disabled. 1 = Intel Prefetch Based Pause is enabled. Reserved FLR_CID--Function Level Reset Capability ID Register (USB EHCI--D29:F0, D26:F0) Address Offset: 98h Default Value: 13h Function Level Reset: No Bit 7:0 15.1.37 Attribute: Size: Description Capability ID--RO. 13h = Capability ID FLR_NEXT--Function Level Reset Next Capability Pointer Register (USB EHCI--D29:F0, D26:F0) Address Offset: 99h Default Value: 00h Function Level Reset: No Bit 7:0 15.1.38 RO 8 bits Attribute: Size: RO 8 bits Description A value of 00h in this register indicates this is the last capability field. FLR_CLV--Function Level Reset Capability Length and Version Register (USB EHCI--D29:F0, D26:F0) Address Offset: 9Ah-9Bh Default Value: 0306h Function Level Reset: No Attribute: Size: R/WO, RO 16 bits When FLRCSSEL = 0, this register is defined as follows: Bit 15:10 9 Datasheet Description Reserved FLR Capability--R/WO. 1 = Support for Function Level Reset (FLR). 559 EHCI Controller Registers (D29:F0, D26:F0) Bit 8 7:0 15.1.39 Description TXP Capability--R/WO. 1 = Support for Transactions Pending (TXP) bit. TXP must be supported if FLR is supported. Capability Length--RO. This field indicates the # of bytes of this vendor specific capability as required by the PCI specification. It has the value of 06h for the FLR capability. FLR_CTRL--Function Level Reset Control Register (USB EHCI--D29:F0, D26:F0) Address Offset: 9Ch Default Value: 00h Function Level Reset: No Bit 7:1 0 15.1.40 Attribute: Size: Description Reserved Initiate FLR--R/W. This bit is used to initiate FLR transition. A write of 1 initiates FLR transition. Since hardware must not respond to any cycles until FLR completion, the value read by software from this bit is always 0. FLR_STS--Function Level Reset Status Register (USB EHCI--D29:F0, D26:F0) Address Offset: 9Dh Default Value: 00h Function Level Reset: No Bit 7:1 0 560 R/W 8 bits Attribute: Size: RO 8 bits Description Reserved Transactions Pending (TXP)--RO. 0 = Completions for all non-posted requests have been received. 1 = Controller has issued non-posted requests which have not been completed. Datasheet EHCI Controller Registers (D29:F0, D26:F0) 15.2 Memory-Mapped I/O Registers The EHCI memory-mapped I/O space is composed of two sets of registers--Capability Registers and Operational Registers. Note: The PCH EHCI controller will not accept memory transactions (neither reads nor writes) as a target that are locked transactions. The locked transactions should not be forwarded to PCI as the address space is known to be allocated to USB. Note: When the EHCI function is in the D3 PCI power state, accesses to the USB 2.0 memory range are ignored and result a master abort. Similarly, if the Memory Space Enable (MSE) bit (D29:F0, D26:F0:04h, bit 1) is not set in the Command register in configuration space, the memory range will not be decoded by the PCH enhanced host controller (EHC). If the MSE bit is not set, the PCH must default to allowing any memory accesses for the range specified in the BAR to go to PCI. This is because the range may not be valid and, therefore, the cycle must be made available to any other targets that may be currently using that range. 15.2.1 Host Controller Capability Registers These registers specify the limits, restrictions and capabilities of the host controller implementation. Within the host controller capability registers, only the structural parameters register is writable. These registers are implemented in the suspend well and is only reset by the standard suspend-well hardware reset, not by HCRESET or the D3-to-D0 reset. Note: The EHCI controller does not support as a target memory transactions that are locked transactions. Attempting to access the EHCI controller Memory-Mapped I/O space using locked memory transactions will result in undefined behavior. Note: When the USB2 function is in the D3 PCI power state, accesses to the USB2 memory range are ignored and will result in a master abort. Similarly, if the Memory Space Enable (MSE) bit is not set in the Command register in configuration space, the memory range will not be decoded by the Enhanced Host Controller (EHC). If the MSE bit is not set, the EHC will not claim any memory accesses for the range specified in the BAR. Table 15-1. Enhanced Host Controller Capability Registers MEM_BASE + Offset Register 00h CAPLENGTH Capabilities Registers Length 02h-03h HCIVERSION Host Controller Interface Version Number 04h-07h HCSPARAMS 08h-0Bh HCCPARAMS Note: Datasheet Mnemonic Default Attribute 20h RO 0100h RO Host Controller Structural Parameters 00204208h (D29:F0) 00203206 (D26:F0) R/W (special), RO Host Controller Capability Parameters 0003688h R/W, RO "Read/Write Special" means that the register is normally read-only, but may be written when the WRT_RDONLY bit is set. Because these registers are expected to be programmed by BIOS during initialization, their contents must not get modified by HCRESET or D3-to-D0 internal reset. 561 EHCI Controller Registers (D29:F0, D26:F0) 15.2.1.1 CAPLENGTH--Capability Registers Length Register Offset: Default Value: MEM_BASE + 00h 20h Bit 7:0 15.2.1.2 Capability Register Length Value--RO. This register is used as an offset to add to the Memory Base Register (D29:F0, D26:F0:10h) to find the beginning of the Operational Register Space. This field is hardwired to 20h indicating that the Operation Registers begin at offset 20h. HCIVERSION--Host Controller Interface Version Number Register MEM_BASE + 02h-03h 0100h Bit 15:0 Attribute: Size: Host Controller Interface Version Number--RO. This is a two-byte register containing a BCD encoding of the version number of interface that this host controller interface conforms. HCSPARAMS--Host Controller Structural Parameters MEM_BASE + 04h-07h 00200008h (D29:F0) 00200006h (D26:F0) Function Level Reset: No Attribute: Size: R/W, RO 32 bits This register is reset by a suspend well reset and not a D3-to-D0 reset or HCRESET. Bit Description 31:24 Reserved 23:20 Debug Port Number (DP_N)--RO. Hardwired to 2h indicating that the Debug Port is on the second lowest numbered port on the EHCI. EHCI#1: Port 1 EHCI#2: Port 9 19:16 Reserved 15:12 Number of Companion Controllers (N_CC)--RO. This field indicates the number of companion controllers associated with this USB EHCI host controller.There are no companion controllers so this field is set to zero as a read only bit. 11:8 Number of Ports per Companion Controller (N_PCC)--RO. This field indicates the number of ports supported per companion host controller. This field is 0h indication no other companion controller support. 7:4 Reserved. These bits are reserved and default to 0. 3:0 N_PORTS--R/W. This field specifies the number of physical downstream ports implemented on this host controller. The value of this field determines how many port registers are addressable in the Operational Register Space. Valid values are in the range of 1h to Fh. A 0 in this field is undefined. For Integrated USB 2.0 Rate Matching Hub Enabled: Each EHCI reports 2 ports by default. Port 0 assigned to the RMH and port 1 assigned as the debug port. When the KVM/USB-R feature is enabled it will show up as Port2 on the EHCI, and BIOS would need to update this field to 3h. Note: 562 RO 16 bits Description Offset: Default Value: Note: RO 8 bits Description Offset: Default Value: 15.2.1.3 Attribute: Size: This register is writable when the WRT_RDONLY bit is set. Datasheet EHCI Controller Registers (D29:F0, D26:F0) 15.2.1.4 HCCPARAMS--Host Controller Capability Parameters Register Offset: Default Value: MEM_BASE + 08h-0Bh 00036881h Bit 31:18 R/W, RO 32 bits Description Reserved 17 Asynchronous Schedule Update Capability (ASUC)--R/W. This bit indicates that the hardware supports the Asynch schedule prefetch enable bit in the USB command register. 16 Periodic Schedule Update Capability (PSUC)--R/W. This field indicates that the EHC hardware supports the Periodic Schedule prefetch bit in the USB2.0_CMD register. 15:8 EHCI Extended Capabilities Pointer (EECP)--RO. This field is hardwired to 68h, indicating that the EHCI capabilities list exists and begins at offset 68h in the PCI configuration space. 7:4 Isochronous Scheduling Threshold--R/W. This field indicates, relative to the current position of the executing host controller, where software can reliably update the isochronous schedule. When bit 7 is 0, the value of the least significant 3 bits indicates the number of micro-frames a host controller hold a set of isochronous data structures (one or more) before flushing the state. When bit 7 is a 1, then host software assumes the host controller may cache an isochronous data structure for an entire frame. Refer to the EHCI specification for details on how software uses this information for scheduling isochronous transfers. This field is hardwired to 8h. 3 Reserved 2 Asynchronous Schedule Park Capability--RO. This bit is hardwired to 0 indicating that the host controller does not support this optional feature 1 Programmable Frame List Flag--RO. 0 = System software must use a frame list length of 1024 elements with this host controller. The USB2.0_CMD register (D29:F0, D26:F0:CAPLENGTH + 20h, bits 3:2) Frame List Size field is a read-only register and must be set to 0. 1 = System software can specify and use a smaller frame list and configure the host controller using the USB2.0_CMD register Frame List Size field. The frame list must always be aligned on a 4K page boundary. This requirement ensures that the frame list is always physically contiguous. 0 64-bit Addressing Capability--RO. This field documents the addressing range capability of this implementation. The value of this field determines whether software should use the 32-bit or 64-bit data structures. This bit is hardwired to 1. Note: Datasheet Attribute: Size: The PCH supports 64-bit addressing only. 563 EHCI Controller Registers (D29:F0, D26:F0) 15.2.2 Host Controller Operational Registers This section defines the enhanced host controller operational registers. These registers are located after the capabilities registers. The operational register base must be DWord-aligned and is calculated by adding the value in the first capabilities register (CAPLENGTH) to the base address of the enhanced host controller register address space (MEM_BASE). Since CAPLENGTH is always 20h, Table 15-2 already accounts for this offset. All registers are 32 bits in length. Table 15-2. Enhanced Host Controller Operational Register Address Map Note: MEM_BAS E + Offset Mnemonic 20h-23h USB2.0_CMD USB 2.0 Command 00080000h R/W, RO 24h-27h USB2.0_STS USB 2.0 Status 00001000h R/WC, RO 28h-2Bh USB2.0_INTR 2Ch-2Fh FRINDEX 30h-33h Register Name Default Special Notes Attribute USB 2.0 Interrupt Enable 00000000h R/W, RO USB 2.0 Frame Index 00000000h R/W, RO CTRLDSSEGMENT Control Data Structure Segment 00000000h R/W, RO 34h-37h PERIODICLISTBAS E Periodic Frame List Base Address 00000000h R/W, RO 38h-3Bh ASYNCLISTADDR Current Asynchronous List Address 00000000h R/W, RO 3Ch-5Fh -- 0h RO 60h-63h CONFIGFLAG Configure Flag 00000000h Suspend R/W, RO 64h-67h PORT1SC Port 1 Status and Control 00003000h Suspend R/W, R/WC, RO 68h-6Bh PORT2SC Port 2 Status and Control 00003000h Suspend R/W, R/WC, RO 6Ch-6Fh PORT3SC Port 3 Status and Control 00003000h Suspend R/W, R/WC, RO Reserved A0h-B3h -- Debug Port Registers Undefined R/W, RO B4h-3FFh -- Reserved Undefined RO Software must read and write these registers using only DWord accesses.These registers are divided into two sets. The first set at offsets MEM_BASE + 00:3Bh are implemented in the core power well. Unless otherwise noted, the core well registers are reset by the assertion of any of the following: * Core well hardware reset * HCRESET * D3-to-D0 reset The second set at offsets MEM_BASE + 60h to the end of the implemented register space are implemented in the Suspend power well. Unless otherwise noted, the suspend well registers are reset by the assertion of either of the following: * Suspend well hardware reset * HCRESET 564 Datasheet EHCI Controller Registers (D29:F0, D26:F0) 15.2.2.1 USB2.0_CMD--USB 2.0 Command Register Offset: Default Value: MEM_BASE + 20-23h 00080000h Bit R/W, RO 32 bits Description 31:24 Reserved 23:16 Interrupt Threshold Control--R/W. System software uses this field to select the maximum rate at which the host controller will issue interrupts. The only valid values are defined below. If software writes an invalid value to this register, the results are undefined. Value 15:14 Datasheet Attribute: Size: Maximum Interrupt Interval 00h Reserved 01h 1 micro-frame 02h 2 micro-frames 04h 4 micro-frames 08h 8 micro-frames (default, equates to 1 ms) 10h 16 micro-frames (2 ms) 20h 32 micro-frames (4 ms) 40h 64 micro-frames (8 ms) Reserved 13 Asynch Schedule Update (ASC)--R/W. This bit is used by the EHCI Asycnh schedule caching function.when operating in C0 mode. it is ignored when Asynch caching operates in Cx mode. When this bit is set, it allows the asynch schedule to be cached. When cleared, it causes the cache to be disabled and all modified entries to be written back. 12 Periodic Schedule Prefetch Enable--R/W. This bit is used by software to enable the host controller to prefetch the periodic schedule even in C0. 0 = Prefetch based pause enabled only when not in C0. 1 = Prefetch based pause enable in C0. Once software has written a 1b to this bit to enable periodic schedule prefetching, it must disable prefetching by writing a 0b to this bit whenever periodic schedule updates are about to begin. Software should continue to dynamically disable and re-enable the prefetcher surrounding any updates to the periodic scheduler (that is, until the host controller has been reset using a HCRESET). 11:8 Unimplemented Asynchronous Park Mode Bits--RO. Hardwired to 000b indicating the host controller does not support this optional feature. 7 Light Host Controller Reset--RO. Hardwired to 0. The PCH does not implement this optional reset. 6 Interrupt on Async Advance Doorbell--R/W. This bit is used as a doorbell by software to tell the host controller to issue an interrupt the next time it advances asynchronous schedule. 0 = The host controller sets this bit to a 0 after it has set the Interrupt on Async Advance status bit (D29:F0, D26:F0:CAPLENGTH + 24h, bit 5) in the USB2.0_STS register to a 1. 1 = Software must write a 1 to this bit to ring the doorbell. When the host controller has evicted all appropriate cached schedule state, it sets the Interrupt on Async Advance status bit in the USB2.0_STS register. If the Interrupt on Async Advance Enable bit in the USB2.0_INTR register (D29:F0, D26:F0:CAPLENGTH + 28h, bit 5) is a 1 then the host controller will assert an interrupt at the next interrupt threshold. See the EHCI specification for operational details. Note: Software should not write a 1 to this bit when the asynchronous schedule is inactive. Doing so will yield undefined results. 5 Asynchronous Schedule Enable--R/W. This bit controls whether the host controller skips processing the Asynchronous Schedule. 0 = Do not process the Asynchronous Schedule 1 = Use the ASYNCLISTADDR register to access the Asynchronous Schedule. 4 Periodic Schedule Enable--R/W. This bit controls whether the host controller skips processing the Periodic Schedule. 0 = Do not process the Periodic Schedule 1 = Use the PERIODICLISTBASE register to access the Periodic Schedule. 565 EHCI Controller Registers (D29:F0, D26:F0) Bit Description 3:2 Frame List Size--RO. This field is R/W only if Programmable Frame List Flag in the HCCPARAMS registers is set to a one. This field specifies the size of the frame list. 00b = 1024 elements (4096 bytes) - Default value 01b = 512 elements (2048 bytes) 10b = 256 elements (1024 bytes) for resource constrained environments. 1 Host Controller Reset (HCRESET)--R/W. This control bit used by software to reset the host controller. The effects of this on root hub registers are similar to a Chip Hardware Reset (that is, RSMRST# assertion and PWROK de-assertion on the PCH). When software writes a 1 to this bit, the host controller resets its internal pipelines, timers, counters, state machines, and so on to their initial value. Any transaction currently in progress on USB is immediately terminated. A USB reset is not driven on downstream ports. Note: PCI configuration registers and Host controller capability registers are not effected by this reset. All operational registers, including port registers and port state machines are set to their initial values. Port ownership reverts to the companion host controller(s), with the side effects described in the EHCI specification. Software must re-initialize the host controller in order to return the host controller to an operational state. This bit is set to 0 by the host controller when the reset process is complete. Software cannot terminate the reset process early by writing a 0 to this register. Software should not set this bit to a 1 when the HCHalted bit (D29:F0, D26:F0:CAPLENGTH + 24h, bit 12) in the USB2.0_STS register is a 0. Attempting to reset an actively running host controller will result in undefined behavior. This reset me be used to leave EHCI port test modes. 0 Run/Stop (RS)--R/W. 0 = Stop (default) 1 = Run. When set to a 1, the Host controller proceeds with execution of the schedule. The Host controller continues execution as long as this bit is set. When this bit is set to 0, the Host controller completes the current transaction on the USB and then halts. The HCHalted bit in the USB2.0_STS register indicates when the Host controller has finished the transaction and has entered the stopped state. Software should not write a 1 to this field unless the host controller is in the Halted state (that is, HCHalted in the USBSTS register is a 1). The Halted bit is cleared immediately when the Run bit is set. The following table explains how the different combinations of Run and Halted should be interpreted: Run/Stop Halted 0b 0b Interpretation In the process of halting 0b 1b Halted 1b 0b Running 1b 1b Invalid - the HCHalted bit clears immediately Memory read cycles initiated by the EHC that receive any status other than Successful will result in this bit being cleared. Note: 566 The Command Register indicates the command to be executed by the serial bus host controller. Writing to the register causes a command to be executed. Datasheet EHCI Controller Registers (D29:F0, D26:F0) 15.2.2.2 USB2.0_STS--USB 2.0 Status Register Offset: Default Value: MEM_BASE + 24h-27h 00001000h Attribute: Size: R/WC, RO 32 bits This register indicates pending interrupts and various states of the Host controller. The status resulting from a transaction on the serial bus is not indicated in this register. See the Interrupts description in section 4 of the EHCI specification for additional information concerning USB 2.0 interrupt conditions. Note: For the writable bits, software must write a 1 to clear bits that are set. Writing a 0 has no effect. Bit 31:16 15 Description Reserved Asynchronous Schedule Status RO. This bit reports the current real status of the Asynchronous Schedule. 0 = Disabled. (Default) 1 = Enabled. Note: 14 Periodic Schedule Status RO. This bit reports the current real status of the Periodic Schedule. 0 = Disabled. (Default) 1 = Enabled. Note: The Host controller is not required to immediately disable or enable the Periodic Schedule when software transitions the Periodic Schedule Enable bit (D29:F0, D26:F0:CAPLENGTH + 20h, bit 4) in the USB2.0_CMD register. When this bit and the Periodic Schedule Enable bit are the same value, the Periodic Schedule is either enabled (1) or disabled (0). 13 Reclamation RO. This read-only status bit is used to detect an empty asynchronous schedule. The operational model and valid transitions for this bit are described in Section 4 of the EHCI Specification. 12 HCHalted RO. 0 = This bit is a 0 when the Run/Stop bit is a 1. 1 = The Host controller sets this bit to 1 after it has stopped executing as a result of the Run/Stop bit being set to 0, either by software or by the Host controller hardware (such as, internal error). (Default) 11:6 Datasheet The Host controller is not required to immediately disable or enable the Asynchronous Schedule when software transitions the Asynchronous Schedule Enable bit (D29:F0, D26:F0:CAPLENGTH + 20h, bit 5) in the USB2.0_CMD register. When this bit and the Asynchronous Schedule Enable bit are the same value, the Asynchronous Schedule is either enabled (1) or disabled (0). Reserved 5 Interrupt on Async Advance--R/WC. System software can force the host controller to issue an interrupt the next time the host controller advances the asynchronous schedule by writing a 1 to the Interrupt on Async Advance Doorbell bit (D29:F0, D26:F0:CAPLENGTH + 20h, bit 6) in the USB2.0_CMD register. This bit indicates the assertion of that interrupt source. 4 Host System Error--R/WC. 0 = No serious error occurred during a host system access involving the Host controller module 1 = The Host controller sets this bit to 1 when a serious error occurs during a host system access involving the Host controller module. A hardware interrupt is generated to the system. Memory read cycles initiated by the EHC that receive any status other than Successful will result in this bit being set. When this error occurs, the Host controller clears the Run/Stop bit in the USB2.0_CMDregister (D29:F0, D26:F0:CAPLENGTH + 20h, bit 0) to prevent further execution of the scheduled TDs. A hardware interrupt is generated to the system (if enabled in the Interrupt Enable Register). 3 Frame List Rollover--R/WC. 0 = No Frame List Index rollover from its maximum value to 0. 1 = The Host controller sets this bit to a 1 when the Frame List Index rolls over from its maximum value to 0. Since the PCH only supports the 1024-entry Frame List Size, the Frame List Index rolls over every time FRNUM13 toggles. 567 EHCI Controller Registers (D29:F0, D26:F0) 568 Bit Description 2 Port Change Detect--R/WC. This bit is allowed to be maintained in the Auxiliary power well. Alternatively, it is also acceptable that on a D3 to D0 transition of the EHCI HC device, this bit is loaded with the OR of all of the PORTSC change bits (including: Force port resume, overcurrent change, enable/disable change and connect status change). Regardless of the implementation, when this bit is readable (that is, in the D0 state), it must provide a valid view of the Port Status registers. 0 = No change bit transition from a 0 to 1 or No Force Port Resume bit transition from 0 to 1 as a result of a J-K transition detected on a suspended port. 1 = The Host controller sets this bit to 1 when any port for which the Port Owner bit is set to 0 has a change bit transition from a 0 to 1 or a Force Port Resume bit transition from 0 to 1 as a result of a J-K transition detected on a suspended port. 1 USB Error Interrupt (USBERRINT)--R/WC. 0 = No error condition. 1 = The Host controller sets this bit to 1 when completion of a USB transaction results in an error condition (such as, error counter underflow). If the TD on which the error interrupt occurred also had its IOC bit set, both this bit and Bit 0 are set. See the EHCI specification for a list of the USB errors that will result in this interrupt being asserted. 0 USB Interrupt (USBINT)--R/WC. 0 = No completion of a USB transaction whose Transfer Descriptor had its IOC bit set. No short packet is detected. 1 = The Host controller sets this bit to 1 when the cause of an interrupt is a completion of a USB transaction whose Transfer Descriptor had its IOC bit set. The Host controller also sets this bit to 1 when a short packet is detected (actual number of bytes received was less than the expected number of bytes). Datasheet EHCI Controller Registers (D29:F0, D26:F0) 15.2.2.3 USB2.0_INTR--USB 2.0 Interrupt Enable Register Offset: Default Value: MEM_BASE + 28h-2Bh 00000000h Attribute: Size: R/W, RO 32 bits This register enables and disables reporting of the corresponding interrupt to the software. When a bit is set and the corresponding interrupt is active, an interrupt is generated to the host. Interrupt sources that are disabled in this register still appear in the USB2.0_STS Register to allow the software to poll for events. Each interrupt enable bit description indicates whether it is dependent on the interrupt threshold mechanism (see Section 4 of the EHCI specification), or not. Bit 31:6 Datasheet Description Reserved 5 Interrupt on Async Advance Enable--R/W. 0 = Disable. 1 = Enable. When this bit is a 1, and the Interrupt on Async Advance bit (D29:F0, D26:F0:CAPLENGTH + 24h, bit 5) in the USB2.0_STS register is a 1, the host controller will issue an interrupt at the next interrupt threshold. The interrupt is acknowledged by software clearing the Interrupt on Async Advance bit. 4 Host System Error Enable--R/W. 0 = Disable. 1 = Enable. When this bit is a 1, and the Host System Error Status bit (D29:F0, D26:F0:CAPLENGTH + 24h, bit 4) in the USB2.0_STS register is a 1, the host controller will issue an interrupt. The interrupt is acknowledged by software clearing the Host System Error bit. 3 Frame List Rollover Enable--R/W. 0 = Disable. 1 = Enable. When this bit is a 1, and the Frame List Rollover bit (D29:F0, D26:F0:CAPLENGTH + 24h, bit 3) in the USB2.0_STS register is a 1, the host controller will issue an interrupt. The interrupt is acknowledged by software clearing the Frame List Rollover bit. 2 Port Change Interrupt Enable--R/W. 0 = Disable. 1 = Enable. When this bit is a 1, and the Port Change Detect bit (D29:F0, D26:F0:CAPLENGTH + 24h, bit 2) in the USB2.0_STS register is a 1, the host controller will issue an interrupt. The interrupt is acknowledged by software clearing the Port Change Detect bit. 1 USB Error Interrupt Enable--R/W. 0 = Disable. 1 = Enable. When this bit is a 1, and the USBERRINT bit (D29:F0, D26:F0:CAPLENGTH + 24h, bit 1) in the USB2.0_STS register is a 1, the host controller will issue an interrupt at the next interrupt threshold. The interrupt is acknowledged by software by clearing the USBERRINT bit in the USB2.0_STS register. 0 USB Interrupt Enable--R/W. 0 = Disable. 1 = Enable. When this bit is a 1, and the USBINT bit (D29:F0, D26:F0:CAPLENGTH + 24h, bit 0) in the USB2.0_STS register is a 1, the host controller will issue an interrupt at the next interrupt threshold. The interrupt is acknowledged by software by clearing the USBINT bit in the USB2.0_STS register. 569 EHCI Controller Registers (D29:F0, D26:F0) 15.2.2.4 FRINDEX--Frame Index Register Offset: Default Value: MEM_BASE + 2Ch-2Fh 00000000h Attribute: Size: R/W, RO 32 bits The SOF frame number value for the bus SOF token is derived or alternatively managed from this register. Refer to Section 4 of the EHCI specification for a detailed explanation of the SOF value management requirements on the host controller. The value of FRINDEX must be within 125 s (1 micro-frame) ahead of the SOF token value. The SOF value may be implemented as an 11-bit shadow register. For this discussion, this shadow register is 11 bits and is named SOFV. SOFV updates every 8 micro-frames (1 millisecond). An example implementation to achieve this behavior is to increment SOFV each time the FRINDEX[2:0] increments from 0 to 1. Software must use the value of FRINDEX to derive the current micro-frame number, both for high-speed isochronous scheduling purposes and to provide the get microframe number function required to client drivers. Therefore, the value of FRINDEX and the value of SOFV must be kept consistent if chip is reset or software writes to FRINDEX. Writes to FRINDEX must also write-through FRINDEX[13:3] to SOFV[10:0]. In order to keep the update as simple as possible, software should never write a FRINDEX value where the three least significant bits are 111b or 000b. Note: This register is used by the host controller to index into the periodic frame list. The register updates every 125 microseconds (once each micro-frame). Bits [12:3] are used to select a particular entry in the Periodic Frame List during periodic schedule execution. The number of bits used for the index is fixed at 10 for the PCH since it only supports 1024-entry frame lists. This register must be written as a DWord. Word and byte writes produce undefined results. This register cannot be written unless the Host controller is in the Halted state as indicated by the HCHalted bit (D29:F0, D26:F0:CAPLENGTH + 24h, bit 12). A write to this register while the Run/Stop bit (D29:F0, D26:F0:CAPLENGTH + 20h, bit 0) is set to a 1 (USB2.0_CMD register) produces undefined results. Writes to this register also effect the SOF value. See Section 4 of the EHCI specification for details. Bit 31:14 13:0 570 Description Reserved Frame List Current Index/Frame Number--R/W. The value in this register increments at the end of each time frame (such as, micro-frame). Bits [12:3] are used for the Frame List current index. This means that each location of the frame list is accessed 8 times (frames or micro-frames) before moving to the next index. Datasheet EHCI Controller Registers (D29:F0, D26:F0) 15.2.2.5 CTRLDSSEGMENT--Control Data Structure Segment Register Offset: Default Value: MEM_BASE + 30h-33h 00000000h Attribute: Size: R/W, RO 32 bits This 32-bit register corresponds to the most significant address bits [63:32] for all EHCI data structures. Since the PCH hardwires the 64-bit Addressing Capability field in HCCPARAMS to 1, this register is used with the link pointers to construct 64-bit addresses to EHCI control data structures. This register is concatenated with the link pointer from either the PERIODICLISTBASE, ASYNCLISTADDR, or any control data structure link field to construct a 64-bit address. This register allows the host software to locate all control data structures within the same 4 GB memory segment. 15.2.2.6 Bit Description 31:12 Upper Address[63:44]--RO. Hardwired to 0s. The PCH EHC is only capable of generating addresses up to 16 terabytes (44 bits of address). 11:0 Upper Address[43:32]--R/W. This 12-bit field corresponds to address bits 43:32 when forming a control data structure address. PERIODICLISTBASE--Periodic Frame List Base Address Register Offset: Default Value: MEM_BASE + 34h-37h 00000000h Attribute: Size: R/W 32 bits This 32-bit register contains the beginning address of the Periodic Frame List in the system memory. Since the PCH host controller operates in 64-bit mode (as indicated by the 1 in the 64-bit Addressing Capability field in the HCCSPARAMS register) (offset 08h, bit 0), then the most significant 32 bits of every control data structure address comes from the CTRLDSSEGMENT register. HCD loads this register prior to starting the schedule execution by the host controller. The memory structure referenced by this physical memory pointer is assumed to be 4-Kbyte aligned. The contents of this register are combined with the Frame Index Register (FRINDEX) to enable the Host controller to step through the Periodic Frame List in sequence. Bit 31:12 11:0 Datasheet Description Base Address (Low)--R/W. These bits correspond to memory address signals 31:12, respectively. Reserved 571 EHCI Controller Registers (D29:F0, D26:F0) 15.2.2.7 ASYNCLISTADDR--Current Asynchronous List Address Register Offset: Default Value: MEM_BASE + 38h-3Bh 00000000h Attribute: Size: R/W 32 bits This 32-bit register contains the address of the next asynchronous queue head to be executed. Since the PCH host controller operates in 64-bit mode (as indicated by a 1 in 64-bit Addressing Capability field in the HCCPARAMS register) (offset 08h, bit 0), then the most significant 32 bits of every control data structure address comes from the CTRLDSSEGMENT register (offset 08h). Bits [4:0] of this register cannot be modified by system software and will always return 0s when read. The memory structure referenced by this physical memory pointer is assumed to be 32-byte aligned. Bit 31:5 4:0 15.2.2.8 Description Link Pointer Low (LPL)--R/W. These bits correspond to memory address signals 31:5, respectively. This field may only reference a Queue Head (QH). Reserved CONFIGFLAG--Configure Flag Register Offset: Default Value: MEM_BASE + 60h-63h 00000000h Attribute: Size: R/W 32 bits This register is in the suspend power well. It is only reset by hardware when the suspend power is initially applied or in response to a host controller reset. Bit 31:1 0 15.2.2.9 Description Reserved Configure Flag (CF)--R/W. Host software sets this bit as the last action in its process of configuring the Host controller. This bit controls the default port-routing control logic. Bit values and side-effects are listed below. See Chapter 4 of the EHCI specification for operation details. 0 = Compatibility debug only (default). 1 = Port routing control logic default-routes all ports to this host controller. PORTSC--Port N Status and Control Register Offset: Attribute: Default Value: Note: Port 0 RMH: MEM_BASE + 64h-67h Port 1 Debug Port: MEM_BASE + 68-6Bh Port 2 USB redirect (if enabled): MEM_BASE + 6C-6Fh R/W, R/WC, RO 00003000h Size: 32 bits This register is associated with the upstream ports of the EHCI controller and does not represent downstream hub ports. USB Hub class commands must be used to determine RMH port status and enable test modes. See Chapter 11 of the USB Specification, Revision 2.0 for more details. Rate Matching Hub wake capabilities can be configured by the RMHWKCTL Register (RCBA+35B0h) located in the Chipset Configuration chapter. A host controller must implement one or more port registers. Software uses the N_Port information from the Structural Parameters Register to determine how many ports need to be serviced. All ports have the structure defined below. Software must not write to unreported Port Status and Control Registers. 572 Datasheet EHCI Controller Registers (D29:F0, D26:F0) This register is in the suspend power well. It is only reset by hardware when the suspend power is initially applied or in response to a host controller reset. The initial conditions of a port are: * No device connected * Port disabled. When a device is attached, the port state transitions to the attached state and system software will process this as with any status change notification. Refer to Section 4 of the EHCI specification for operational requirements for how change events interact with port suspend mode. Bit 31:23 Description Reserved 22 Wake on Overcurrent Enable (WKOC_E)--R/W. 0 = Disable. (Default) 1 = Enable. Writing this bit to a 1 enables the setting of the PME Status bit in the Power Management Control/Status Register (offset 54, bit 15) when the overcurrent Active bit (bit 4 of this register) is set. 21 Wake on Disconnect Enable (WKDSCNNT_E)--R/W. 0 = Disable. (Default) 1 = Enable. Writing this bit to a 1 enables the setting of the PME Status bit in the Power Management Control/Status Register (offset 54, bit 15) when the Current Connect Status changes from connected to disconnected (that is, bit 0 of this register changes from 1 to 0). 20 Wake on Connect Enable (WKCNNT_E)--R/W. 0 = Disable. (Default) 1 = Enable. Writing this bit to a 1 enables the setting of the PME Status bit in the Power Management Control/Status Register (offset 54, bit 15) when the Current Connect Status changes from disconnected to connected (that is, bit 0 of this register changes from 0 to 1). 19:16 Port Test Control--R/W. When this field is 0s, the port is NOT operating in a test mode. A non-zero value indicates that it is operating in test mode and the specific test mode is indicated by the specific value. The encoding of the test mode bits are (0110b - 1111b are reserved): Value Maximum Interrupt Interval 0000b Test mode not enabled (default) 0001b Test J_STATE 0010b Test K_STATE 0011b Test SE0_NAK 0100b Test Packet 0101b FORCE2.0, ENABLE Refer to the USB Specification Revision Chapter 7 for details on each test mode. 15:14 Port Owner--R/W. This bit unconditionally goes to a 0 when the Configured Flag bit in the USB2.0_CMD register makes a 0 to 1 transition. System software uses this field to release ownership of the port to a selected host controller (in the event that the attached device is not a high-speed device). Software writes a 1 to this bit when the attached device is not a high-speed device. A 1 in this bit means that a companion host controller owns and controls the port. See Section 4 of the EHCI Specification for operational details. 12 Port Power (PP)--RO. Read-only with a value of 1. This indicates that the port does have power. 11:10 Datasheet Reserved 13 Line Status--RO.These bits reflect the current logical levels of the D+ (bit 11) and D- (bit 10) signal lines. These bits are used for detection of low-speed USB devices prior to the port reset and enable sequence. This field is valid only when the port enable bit is 0 and the current connect status bit is set to a 1. 00 = SE0 10 = J-state 01 = K-state 11 = Undefined 573 EHCI Controller Registers (D29:F0, D26:F0) Bit Description 9 Reserved 8 Port Reset--R/W. When software writes a 1 to this bit (from a 0), the bus reset sequence as defined in the USB Specification, Revision 2.0 is started. Software writes a 0 to this bit to terminate the bus reset sequence. Software must keep this bit at a 1 long enough to ensure the reset sequence completes as specified in the USB Specification, Revision 2.0. 1 = Port is in Reset. 0 = Port is not in Reset. 7 Note: When software writes a 0 to this bit, there may be a delay before the bit status changes to a 0. The bit status will not read as a 0 until after the reset has completed. If the port is in high-speed mode after reset is complete, the host controller will automatically enable this port (such as, set the Port Enable bit to a 1). A host controller must terminate the reset and stabilize the state of the port within 2 milliseconds of software transitioning this bit from 0 to 1. For example: if the port detects that the attached device is high-speed during reset, then the host controller must have the port in the enabled state within 2 ms of software writing this bit to a 0. The HCHalted bit (D29:F0, D26:F0:CAPLENGTH + 24h, bit 12) in the USB2.0_STS register should be a 0 before software attempts to use this bit. The host controller may hold Port Reset asserted to a 1 when the HCHalted bit is a 1. This bit is 0 if Port Power is 0 Note: System software should not attempt to reset a port if the HCHalted bit in the USB2.0_STS register is a 1. Doing so will result in undefined behavior. Suspend--R/W. 0 = Port not in suspend state.(Default) 1 = Port in suspend state. Port Enabled Bit and Suspend bit of this register define the port states as follows: Port Enabled Suspend Port State 0 X Disabled 1 0 Enabled 1 1 Suspend When in suspend state, downstream propagation of data is blocked on this port, except for port reset. The bit status does not change until the port is suspended and that there may be a delay in suspending a port depending on the activity on the port. The host controller will unconditionally set this bit to a 0 when software sets the Force Port Resume bit to a 0 (from a 1). A write of 0 to this bit is ignored by the host controller. If host software sets this bit to a 1 when the port is not enabled (that is, Port enabled bit is a 0), the results are undefined. 6 Force Port Resume--R/W. 0 = No resume (K-state) detected/driven on port. (Default) 1 = Resume detected/driven on port. Software sets this bit to a 1 to drive resume signaling. The Host controller sets this bit to a 1 if a J-to-K transition is detected while the port is in the Suspend state. When this bit transitions to a 1 because a J-to-K transition is detected, the Port Change Detect bit (D29:F0, D26:F0:CAPLENGTH + 24h, bit 2) in the USB2.0_STS register is also set to a 1. If software sets this bit to a 1, the host controller must not set the Port Change Detect bit. Note: 5 574 When the EHCI controller owns the port, the resume sequence follows the defined sequence documented in the USB Specification, Revision 2.0. The resume signaling (Full-speed 'K') is driven on the port as long as this bit remains a 1. Software must appropriately time the Resume and set this bit to a 0 when the appropriate amount of time has elapsed. Writing a 0 (from 1) causes the port to return to high-speed mode (forcing the bus below the port into a high-speed idle). This bit will remain a 1 until the port has switched to the high-speed idle. Overcurrent Change--R/WC. The functionality of this bit is not dependent upon the port owner. Software clears this bit by writing a 1 to it. 0 = No change. (Default) 1 = There is a change to Overcurrent Active. Datasheet EHCI Controller Registers (D29:F0, D26:F0) 15.2.3 Bit Description 4 Overcurrent Active--RO. 0 = This port does not have an overcurrent condition. (Default) 1 = This port currently has an overcurrent condition. This bit will automatically transition from 1 to 0 when the over current condition is removed. The PCH automatically disables the port when the overcurrent active bit is 1. 3 Port Enable/Disable Change--R/WC. For the root hub, this bit gets set to a 1 only when a port is disabled due to the appropriate conditions existing at the EOF2 point (See Chapter 11 of the USB Specification for the definition of a port error). This bit is not set due to the Disabled-to-Enabled transition, nor due to a disconnect. Software clears this bit by writing a 1 to it. 0 = No change in status. (Default). 1 = Port enabled/disabled status has changed. 2 Port Enabled/Disabled--R/W. Ports can only be enabled by the host controller as a part of the reset and enable. Software cannot enable a port by writing a 1 to this bit. Ports can be disabled by either a fault condition (disconnect event or other fault condition) or by host software. The bit status does not change until the port state actually changes. There may be a delay in disabling or enabling a port due to other host controller and bus events. 0 = Disable 1 = Enable (Default) 1 Connect Status Change--R/WC. This bit indicates a change has occurred in the port's Current Connect Status. Software sets this bit to 0 by writing a 1 to it. 0 = No change (Default). 1 = Change in Current Connect Status. The host controller sets this bit for all changes to the port device connect status, even if system software has not cleared an existing connect status change. For example, the insertion status changes twice before system software has cleared the changed condition, hub hardware will be "setting" an already-set bit (that is, the bit will remain set). 0 Current Connect Status--RO. This value reflects the current state of the port, and may not correspond directly to the event that caused the Connect Status Change bit (Bit 1) to be set. 0 = No device is present. (Default) 1 = Device is present on port. USB 2.0-Based Debug Port Registers The Debug port's registers are located in the same memory area, defined by the Base Address Register (MEM_BASE), as the standard EHCI registers. The base offset for the debug port registers (A0h) is declared in the Debug Port Base Offset Capability Register at Configuration offset 5Ah (D29:F0, D26:F0:offset 5Ah). The specific EHCI port that supports this debug capability (Port 1 for D29:F0 and Port 9 for D26:F0) is indicated by a 4-bit field (bits 20-23) in the HCSPARAMS register of the EHCI controller. The address map of the Debug Port registers is shown in Table 15-3. Table 15-3. Debug Port Register Address Map MEM_BASE + Offset Mnemonic A0-A3h CNTL_STS A4-A7h USBPID A8-AFh DATABUF[7:0] B0-B3h CONFIG Register Name Default Attribute Control / Status 00000000h R/W, R/WC, RO USB PIDs 00000000h R/W, RO Data Buffer (Bytes 7:0) 00000000 00000000h R/W Configuration 00007F01h R/W Notes: 1. All of these registers are implemented in the core well and reset by PLTRST#, EHC HCRESET, and a EHC D3-to-D0 transition. 2. The hardware associated with this register provides no checks to ensure that software programs the interface correctly. How the hardware behaves when programmed improperly is undefined. Datasheet 575 EHCI Controller Registers (D29:F0, D26:F0) 15.2.3.1 CNTL_STS--Control / Status Register Offset: Default Value: Power well: MEM_BASE + A0h 00000000h Suspend Bit R/W, R/WC, RO 32 bits Description 31 Reserved 30 OWNER_CNT--R/W. 0 = Ownership of the debug port is NOT forced to the EHCI controller (Default) 1 = Ownership of the debug port is forced to the EHCI controller (that is, immediately taken away from the companion Classic USB Host controller) If the port was already owned by the EHCI controller, then setting this bit has no effect. This bit overrides all of the ownership-related bits in the standard EHCI registers. 29 Reserved 28 ENABLED_CNT--R/W. 0 = Software can clear this by writing a 0 to it. The hardware clears this bit for the same conditions where the Port Enable/Disable Change bit (in the PORTSC register) is set. (Default) 1 = Debug port is enabled for operation. Software can directly set this bit if the port is already enabled in the associated PORTSC register (this is enforced by the hardware). 27:17 16 15:12 Reserved DONE_STS--R/WC. Software can clear this by writing a 1 to it. 0 = Request Not complete 1 = Set by hardware to indicate that the request is complete. LINK_ID_STS--RO. This field identifies the link interface. 0h = Hardwired. Indicates that it is a USB Debug Port. 11 Reserved 10 IN_USE_CNT--R/W. Set by software to indicate that the port is in use. Cleared by software to indicate that the port is free and may be used by other software. This bit is cleared after reset. (This bit has no affect on hardware.) 9:7 EXCEPTION_STS--RO. This field indicates the exception when the ERROR_GOOD#_STS bit is set. This field should be ignored if the ERROR_GOOD#_STS bit is 0. 000 =No Error. (Default) Note: This should not be seen since this field should only be checked if there is an error. 001 =Transaction error: Indicates the USB 2.0 transaction had an error (CRC, bad PID, timeout, and so on) 010 =Hardware error. Request was attempted (or in progress) when port was suspended or reset. All Other combinations are reserved. 6 ERROR_GOOD#_STS--RO. 0 = Hardware clears this bit to 0 after the proper completion of a read or write. (Default) 1 = Error has occurred. Details on the nature of the error are provided in the Exception field. 5 GO_CNT--R/W. 0 = Hardware clears this bit when hardware sets the DONE_STS bit. (Default) 1 = Causes hardware to perform a read or write request. Note: 4 576 Attribute: Size: Writing a 1 to this bit when it is already set may result in undefined behavior. WRITE_READ#_CNT--R/W. Software clears this bit to indicate that the current request is a read. Software sets this bit to indicate that the current request is a write. 0 = Read (Default) 1 = Write Datasheet EHCI Controller Registers (D29:F0, D26:F0) Bit Description 3:0 DATA_LEN_CNT--R/W. This field is used to indicate the size of the data to be transferred. default = 0h. For write operations, this field is set by software to indicate to the hardware how many bytes of data in Data Buffer are to be transferred to the console. A value of 0h indicates that a zero-length packet should be sent. A value of 1-8 indicates 1-8 bytes are to be transferred. Values 9-Fh are invalid and how hardware behaves if used is undefined. For read operations, this field is set by hardware to indicate to software how many bytes in Data Buffer are valid in response to a read operation. A value of 0h indicates that a zero length packet was returned and the state of Data Buffer is not defined. A value of 1-8 indicates 1-8 bytes were received. Hardware is not allowed to return values 9-Fh. The transferring of data always starts with byte 0 in the data area and moves toward byte 7 until the transfer size is reached. Notes: 1. Software should do Read-Modify-Write operations to this register to preserve the contents of bits not being modified. This include Reserved bits. 2. To preserve the usage of RESERVED bits in the future, software should always write the same value read from the bit until it is defined. Reserved bits will always return 0 when read. 15.2.3.2 USBPID--USB PIDs Register Offset: Default Value: Power well: MEM_BASE + A4h-A7h 00000000h Suspend Attribute: Size: R/W, RO 32 bits This DWord register is used to communicate PID information between the USB debug driver and the USB debug port. The debug port uses some of these fields to generate USB packets, and uses other fields to return PID information to the USB debug driver. Bit 31:24 Reserved 23:16 RECEIVED_PID_STS[23:16]--RO. Hardware updates this field with the received PID for transactions in either direction. When the controller is writing data, this field is updated with the handshake PID that is received from the device. When the host controller is reading data, this field is updated with the data packet PID (if the device sent data), or the handshake PID (if the device NAKs the request). This field is valid when the hardware clears the GO_DONE#_CNT bit. 15:8 7:0 15.2.3.3 Description SEND_PID_CNT[15:8]--R/W. Hardware sends this PID to begin the data packet when sending data to USB (that is, WRITE_READ#_CNT is asserted). Software typically sets this field to either DATA0 or DATA1 PID values. TOKEN_PID_CNT[7:0]--R/W. Hardware sends this PID as the Token PID for each USB transaction. Software typically sets this field to either IN, OUT, or SETUP PID values. DATABUF[7:0]--Data Buffer Bytes[7:0] Register Offset: Default Value: MEM_BASE + A8h-AFh 0000000000000000h Attribute: Size: R/W 64 bits This register can be accessed as 8 separate 8-bit registers or 2 separate 32-bit register. Datasheet Bit Description 63:0 DATABUFFER[63:0]--R/W. This field is the 8 bytes of the data buffer. Bits 7:0 correspond to least significant byte (byte 0). Bits 63:56 correspond to the most significant byte (byte 7). The bytes in the Data Buffer must be written with data before software initiates a write request. For a read request, the Data Buffer contains valid data when DONE_STS bit (offset A0, bit 16) is cleared by the hardware, ERROR_GOOD#_STS (offset A0, bit 6) is cleared by the hardware, and the DATA_LENGTH_CNT field (offset A0, bits 3:0) indicates the number of bytes that are valid. 577 EHCI Controller Registers (D29:F0, D26:F0) 15.2.3.4 CONFIG--Configuration Register Offset: Default Value: Bit 31:15 14:8 MEM_BASE + B0-B3h 00007F01h Attribute: Size: R/W 32 bits Description Reserved USB_ADDRESS_CNF--R/W. This 7-bit field identifies the USB device address used by the controller for all Token PID generation. (Default = 7Fh) 7:4 Reserved 3:0 USB_ENDPOINT_CNF--R/W. This 4-bit field identifies the endpoint used by the controller for all Token PID generation. (Default = 1h) 578 Datasheet xHCI Controller Registers (D20:F0) 16 xHCI Controller Registers (D20:F0) 16.1 USB xHCI Configuration Registers (USB xHCI--D20:F0) Note: Register address locations that are not shown in Table 16-1 should be treated as Reserved (see Section 9.2 for details). Note: "Multiple" in the Power Well column means that multiple power wells apply to this register since the individual fields in the register may be on different power wells. Table 16-1. USB xHCI PCI Register Address Map (USB xHCI--D20:F0) (Sheet 1 of 2) Offset Power Well Mnemonic 00h-01h Core VID 02h-03h Core DID 04h-05h Core PCICMD 06h-07h Core PCISTS 08h Core RID 09h Core PI 0Ah Core SCC Register Name Default Value Type Vendor Identification 8086h RO Device Identification See register description RO PCI Command 0000h R/W, RO PCI Status 0290h R/WC, RO Revision Identification 00h RO Programming Interface 30h RO Sub Class Code 03h RO 0Bh Core BCC Base Class Code 0Ch RO 0Dh Core PMLT Primary Master Latency Timer 00h RO 0Eh Core HEADTYP 00h RO 10h-13h Core MEM_BASE_L Memory Base Address Low 00000004h R/W, RO 14h-17h Core MEM_BASE_H Memory Base Address High 2Ch-2Dh Core SVID 2Eh-2Fh Core SID 34h Core CAP_PTR Header Type 00000000h R/W USB xHCI Subsystem Vendor Identification 0000h R/W USB xHCI Subsystem Identification 0000h R/W 70h RO Capabilities Pointer 3Ch Core INT_LN Interrupt Line 00h R/W 3Dh Core INT_PN Interrupt Pin See register description RO xHC System Bus Configuration 0000F0FDh R/W, R/WC xHC System Bus Configuration 2 00000000h R/WO 40h-43h Core XHCC 44h-47h Multiple XHCC2 60h Sus SBRN Serial Bus Release Number 30h RO 61h Multiple FL_ADJ Frame Length Adjustment 20h R/W 70h Core PWR_CAPID PCI Power Management Capability ID 01h RO 71h Core NXT_PTR1 Next Item Pointer #1 80h R/W 72h-73h Core PWR_CAP Power Management Capabilities C9C2h R/W, RO Datasheet 579 xHCI Controller Registers (D20:F0) Table 16-1. USB xHCI PCI Register Address Map (USB xHCI--D20:F0) (Sheet 2 of 2) Offset Power Well Mnemonic 74h-75h Multiple PWR_CNTL_STS 80h Core MSI_CAPID 81h Core NXT_PTR2 82h-83h Core MSI_MCTL MSI Message Control Register 84h-87h Core MSI_LMAD MSI Lower Message Address 88h-8Bh Core MSI_UMAD MSI Upper Message Address 000000h R/W 8Ch-8Fh Core MSI_MD MSI Message Data 00000000h R/W C0h-C3h Sus U2OCM1 XHCI USB2 Overcurrent Pin Mapping 1 00000000h R/W, RO C4h-C7h Sus U2OCM2 XHCI USB2 Overcurrent Pin Mapping 2 00000000h R/W, RO C8h-CBh Sus U3OCM1 XHCI USB3 Overcurrent Pin Mapping 1 00000000h R/W, RO CCh-CFh Sus U3OCM2 XHCI USB3 Overcurrent Pin Mapping 2 00000000h R/W, RO D0h-D3h Multiple XUSB2PR D4h-D7h Core XUSB2PRM D8h-dBh D8h-dBh USB3_PSSEN Multiple USB3PR Register Name Default Value Type 0000h R/W, R/WC, RO Message Signaled Interrupt Capability ID 05h RO Next Item Pointer #2 00h RO 0086h RO, R/W 00000000h RW, RO Power Management Control / Status xHC USB 2.0 Port Routing 00000000h R/W, RO xHC USB 2.0 Port Routing Mask 00000000h RO, R/WLO USB 3.0 Port SuperSpeed Enable Register 00000000h RO, R/W USB3 Port Routing 00000000h R/W, RO DCh-DFh Core USB3PRM USB 3.0 Port Routing Mask 00000000h R/W, RO E4h-E7h Multiple USB2PDO USB2 Port Disable Override 00000000h R/WO E8h-EBh Multiple USB3PDO USB3 Port Disable Override 00000000h R/WO 16.1.1 VID--Vendor Identification Register (USB xHCI--D20:F0) Offset Address: 00h-01h Default Value: 8086h Bit 15:0 16.1.2 RO 16 bits Attribute: Size: RO 16 bits Description Vendor ID--RO. This is a 16-bit value assigned to Intel. DID--Device Identification Register (USB xHCI--D20:F0) Offset Address: 02h-03h Default Value: See bit description 580 Attribute: Size: Bit Description 15:0 Device ID--RO. This is a 16-bit value assigned to the PCH USB xHCI controller. See Section 1.3 for the value of the DID Register. Datasheet xHCI Controller Registers (D20:F0) 16.1.3 PCICMD--PCI Command Register (USB xHCI--D20:F0) Address Offset: 04h-05h Default Value: 0000h Bit 15:11 10 Attribute: Size: R/W, RO 16 bits Description Reserved Interrupt Disable--R/W. 0 = The function is capable of generating interrupts. 1 = The function can not generate its interrupt to the interrupt controller. The corresponding Interrupt Status bit (D20:F0, Offset 06h, bit 3) is not affected by the interrupt enable. 9 Fast Back to Back Enable (FBE)--RO. Hardwired to 0. 8 SERR# Enable (SERR_EN)--R/W. 0 = Disables xHC's capability to generate an SERR#. 1 = The xHCI Host controller (xHC) is capable of generating (internally) SERR# in the following cases: -- When it receive a completion status other than "successful" for one of its DMA initiated memory reads on DMI (and subsequently on its internal interface). -- When it detects an address or command parity error and the Parity Error Response bit is set. -- When it detects a data parity error (when the data is going into the xHC) and the Parity Error Response bit is set. 7 Wait Cycle Control (WCC)--RO. Hardwired to 0. 6 Parity Error Response (PER)--R/W. 0 = The xHC is not checking for correct parity (on its internal interface). 1 = The xHC is checking for correct parity (on its internal interface) and halt operation when bad parity is detected during the data phase. Note: This applies to both requests and completions from the system interface. This bit must be set in order for the parity errors to generate SERR#. Datasheet 5 VGA Palette Snoop (VPS)--RO. Hardwired to 0. 4 Postable Memory Write Enable (PMWE)--RO. Hardwired to 0. 3 Special Cycle Enable (SCE)--RO. Hardwired to 0. 2 Bus Master Enable (BME)--R/W. 0 = Disables this functionality. 1 = Enables the xHC to act as a master on the PCI bus for USB transfers. 1 Memory Space Enable (MSE)--R/W. This bit controls access to the xHC Memory Space registers. 0 = Disables this functionality. 1 = Enables accesses to the xHC Memory Space registers. The Base Address register (D20:F0:10h) should be programmed before this bit is set. 0 I/O Space Enable (IOSE)--RO. Hardwired to 0. 581 xHCI Controller Registers (D20:F0) 16.1.4 PCISTS--PCI Status Register (USB xHCI--D20:F0) Address Offset: 06h-07h Default Value: 0290h Note: R/WC, RO 16 bits For the writable bits, software must write a 1 to clear bits that are set. Writing a 0 to the bit has no effect. Bit Description 15 Detected Parity Error (DPE)--R/WC. 0 = No parity error detected. 1 = This bit is set by the PCH when a parity error is seen by the xHCI controller, regardless of the setting of bit 6 or bit 8 in the Command register or any other conditions. 14 Signaled System Error (SSE)--R/WC. 0 = No SERR# signaled by the PCH. 1 = This bit is set by the PCH when it signals SERR# (internally). The SER_EN bit (bit 8 of the Command Register) must be 1 for this bit to be set. 13 Received Master Abort (RMA)--R/WC. 0 = No master abort received by xHC on a memory access. 1 = This bit is set when xHC, as a master, receives a master abort status on a memory access. This is treated as a Host Error and halts the DMA engines. This event can optionally generate an SERR# by setting the SERR# Enable bit. 12 Received Target Abort (RTA)--R/WC. 0 = No target abort received by xHC on memory access. 1 = This bit is set when xHC, as a master, receives a target abort status on a memory access. This is treated as a Host Error and halts the DMA engines. This event can optionally generate an SERR# by setting the SERR# Enable bit. 11 Signaled Target Abort (STA)--RO. This bit is used to indicate when the xHCI function responds to a cycle with a target abort. There is no reason for this to happen, so this bit is hardwired to 0. 10:9 DEVSEL# Timing Status (DEVT_STS)--RO. This 2-bit field defines the timing for DEVSEL# assertion. 8 Master Data Parity Error Detected (DPED)--R/WC. 0 = No data parity error detected on USB read completion packet. 1 = This bit is set by the PCH when a data parity error is detected on a xHC read completion packet on the internal interface to the xHCI host controller and bit 6 of the Command register is set to 1. 7 Fast Back to Back Capable (FB2BC)--RO. Hardwired to 1. 6 User Definable Features (UDF)--RO. Hardwired to 0. 5 66 MHz Capable (66 MHz _CAP)--RO. Hardwired to 0. 4 Capabilities List (CAP_LIST)--RO. Hardwired to 1 indicating that offset 34h contains a valid capabilities pointer. 3 Interrupt Status--RO. This bit reflects the state of this function's interrupt at the input of the enable/disable logic. 0 = This bit will be 0 when the interrupt is de-asserted. 1 = This bit is a 1 when the interrupt is asserted. The value reported in this bit is independent of the value in the Interrupt Enable bit. 2:0 582 Attribute: Size: Reserved Datasheet xHCI Controller Registers (D20:F0) 16.1.5 RID--Revision Identification Register (USB xHCI--D20:F0) Offset Address: 08h Default Value: See bit description 16.1.6 Attribute: Size: Bit Description 7:0 Revision ID--RO. This field indicates the device specific revision identifier. See Section 1.3 for the value of the Revision ID Register. PI--Programming Interface Register (USB xHCI--D20:F0) Address Offset: 09h Default Value: 30h Bit 7:0 16.1.7 Attribute: Size: Programming Interface--RO. A value of 30h indicates that this USB host controller conforms to the xHCI Specification. SCC--Sub Class Code Register (USB xHCI--D20:F0) Bit 7:0 RO 8 bits Attribute: Size: RO 8 bits Sub Class Code (SCC)--RO. 03h = Universal Serial Bus host controller. BCC--Base Class Code Register (USB xHCI--D20:F0) Bit 7:0 Description Base Class Code (BCC)--RO. 0Ch = Serial bus controller. PMLT--Primary Master Latency Timer Register (USB xHCI--D20:F0) Address Offset: 0Dh Default Value: 00h Bit 7:0 Datasheet Attribute: Size: Description Address Offset: 0Bh Default Value: 0Ch 16.1.9 RO 8 bits Description Address Offset: 0Ah Default Value: 03h 16.1.8 RO 8 bits Attribute: Size: RO 8 bits Description Master Latency Timer Count (MLTC)--RO. Hardwired to 00h. Because the xHCI controller is internally implemented with arbitration on an interface (and not PCI), it does not need a master latency timer. 583 xHCI Controller Registers (D20:F0) 16.1.10 HEADTYP--Header Type Register (USB xHCI--D20:F0) Address Offset: 0Eh Default Value: 00h Bit 7 6:0 16.1.11 Attribute: Size: Description Multi-Function Device--RO. When set to `1' indicates this is a multifunction device: 0 = Single-function device 1 = Multi-function device. Configuration Layout. Hardwired to 00h, which indicates the standard PCI configuration layout. MEM_BASE_L--Memory Base Address Low Register (USB xHCI--D20:F0) Address Offset: 10h-13h Default Value: 00000004h Bit 31:16 15:4 3 2:1 0 16.1.12 Attribute: Size: Base Address--R/W. Bits [31:16] correspond to memory address signals [31:16], respectively. This gives 64 KB of relocatable memory space aligned to 64 KB boundaries. Reserved Prefetchable--RO. Hardwired to 0 indicating that this range should not be prefetched. Type--RO. Hardwired to 10 indicating that this range can be mapped anywhere within 64-bit address space. Resource Type Indicator (RTE)--RO. Hardwired to 0 indicating that the base address field in this register maps to memory space. MEM_BASE_H--Memory Base Address High Register (USB xHCI--D20:F0) Bit 31:0 Attribute: Size: R/W 32 bits Description Base Address--R/W. Bits [63:32] correspond to memory address signals [63:32], respectively. This gives 64 KB of relocatable memory space aligned to 64 KB boundaries. SVID--USB xHCI Subsystem Vendor ID Register (USB xHCI--D20:F0) Address Offset: 2Ch-2Dh Default Value: 0000h Reset: None Bit 15:0 584 R/W, RO 32 bits Description Address Offset: 14h-17h Default Value: 00000000h 16.1.13 RO 8 bits Attribute: Size: R/W 16 bits Description Subsystem Vendor ID (SVID)--R/W. This register, in combination with the xHC Subsystem ID register, enables the operating system to distinguish each subsystem from the others. Datasheet xHCI Controller Registers (D20:F0) 16.1.14 SID--USB xHCI Subsystem ID Register (USB xHCI--D20:F0) Address Offset: 2Eh-2Fh Default Value: 0000h Reset: None 16.1.15 Attribute: Size: Bit Description 15:0 Subsystem ID (SID)--R/W. BIOS sets the value in this register to identify the Subsystem ID. This register, in combination with the Subsystem Vendor ID register, enables the operating system to distinguish each subsystem from other(s). CAP_PTR--Capabilities Pointer Register (USB xHCI--D20:F0) Address Offset: 34h Default Value: 70h Bit 7:0 16.1.16 Attribute: Size: Capabilities Pointer (CAP_PTR)--RO. This register points to the starting offset of the xHC capabilities ranges. INT_LN--Interrupt Line Register (USB xHCI--D20:F0) Bit 7:0 Attribute: Size: Interrupt Line (INT_LN)--R/W. This data is not used by the PCH. It is used as a scratchpad register to communicate to software the interrupt line that the interrupt pin is connected to. INT_PN--Interrupt Pin Register (USB xHCI--D20:F0) Bit 7:0 Attribute: Size: RO 8 bits Description Interrupt Pin--RO. Bits 3:0 reflect the value of the interrupt pin registers in chipset configuration space. Bits 7:4 are always 0h XHCC--xHC System Bus Configuration Register (USB xHCI--D20:F0) Address Offset: 40-43h Default Value: 0000F0FDh Bit 31:25 Datasheet R/W 8 bits Description Address Offset: 3Dh Default Value: See Description 16.1.18 RO 8 bits Description Address Offset: 3Ch Default Value: 00h Function Level Reset: No 16.1.17 R/W 16 bits Attribute: Size: R/W, R/WC 32 bits Description Reserved 585 xHCI Controller Registers (D20:F0) Bit 24 Master/Target Abort SERR (RMTASERR)--R/W. When set, this bit allows the out-of-band error reporting from the xHCI Controller to be reported as SERR# (if SERR# reporting is enabled) and thus setting the STS.SSE bit. 23 Unsupported Request Detected (URD)--R/WC. This bit is set by HW when the xHCI Controller received an unsupported request posted cycle. Once set, this bit is cleared by SW. 22 Unsupported Request Report Enable (URRE)--R/W. When set, this bit allows the URD bit to be reported as SERR# (if SERR# reporting is enabled) and thus setting the STS.SSE bit. 21:19 Inactivity Initiated L1 Enable (IIL1E)--R/W. If programmed to a non-zero value, the bit field allows L1 power management to be enabled after the time-out period specified. 000 = Disabled 001 = 32 bb_cclk 010 = 64 bb_cclk 011 = 128 bb_cclk 100 = 256 bb_cclk 101 = 512 bb_cclk 110 = 1024 bb_cclk 111 = 131072 bb_cclk 18 xHC Initiated L1 Enable (XHCIL1E)--R/W. 0 = xHC-initiated L1 power management is disabled 1 = Allows xHC-initiated L1 power management to be enabled 17 D3 Initiated L1 Enable (D3IL1E)--R/W. 0 = PCI device state D3-initiated L1 power management is disabled 1 = Allows PCI device state D3-initiated L1 power management to be enabled 16:0 16.1.19 Description Reserved XHCC2--xHC System Bus Configuration Register 2 (USB xHCI--D20:F0) Address Offset: 44-47h Default Value: 00000000h Bit 31 30:0 16.1.20 Attribute: Size: Description OC Configuration Done (OCCFDONE)--R/WO. This bit is used by BIOS to prevent spurious switching during OC configuration. Note: This bit must be set by BIOS after configuration of the OC mapping bits is complete. Once this bit is set, OC mapping shall not be changed by SW. Reserved SBRN--Serial Bus Release Number Register (USB xHCI--D20:F0) Address Offset: 60h Default Value: 30h Bit 7:0 586 R/WO 32 bits Attribute: Size: RO 8 bits Description Serial Bus Release Number (SBRN)--RO. A value of 30h indicates that this controller follows USB release 3.0. Datasheet xHCI Controller Registers (D20:F0) 16.1.21 FL_ADJ--Frame Length Adjustment Register (USB xHCI--D20:F0) Address Offset: 61h Default Value: 20h Function Level Reset: No Attribute: Size: R/W 8 bits This feature is used to adjust any offset from the clock source that generates the clock that drives the SOF counter. When a new value is written into these six bits, the length of the frame is adjusted. Its initial programmed value is system dependent based on the accuracy of hardware USB clock and is initialized by system BIOS. This register should only be modified when the HChalted bit (D20:F0:CAPLENGTH + 84h, bit 0) in the USB_STS register is a 1. Changing value of this register while the host controller is operating yields undefined results. It should not be reprogrammed by USB system software unless the default or BIOS programmed values are incorrect, or the system is restoring the register while returning from a suspended state. These bits in suspend well and not reset by a D3-to-D0 warm rest or a core well reset. Bit 16.1.22 Description 7:6 Reserved--RO. These bits are reserved for future use and should read as 00b. 5:0 Frame Length Timing Value--R/W. Each decimal value change to this register corresponds to 16 high-speed bit times. The SOF cycle time (number of SOF counter clock periods to generate a SOF micro-frame length) is equal to 59488 + value in this field. The default value is decimal 32 (20h), which gives a SOF cycle time of 60000. Frame Length (# 480 MHz Clocks) (decimal) Frame Length Timing Value (this register) (decimal) 59488 0 59504 1 59520 2 ... ... 59984 31 ... ... 60496 63 60480 62 60496 63 PWR_CAPID--PCI Power Management Capability ID Register (USB xHCI--D20:F0) Address Offset: 70h Default Value: 01h Bit 7:0 Datasheet Attribute: Size: RO 8 bits Description Power Management Capability ID--RO. A value of 01h indicates that this is a PCI Power Management capabilities field. 587 xHCI Controller Registers (D20:F0) 16.1.23 NXT_PTR1--Next Item Pointer #1 Register (USB xHCI--D20:F0) Address Offset: 71h Default Value: 80h 16.1.24 Attribute: Size: R/W 8 bits Bit Description 7:0 Next Item Pointer 1 Value--R/W (special). This register defaults to 80h, which indicates that the next capability registers begin at configuration offset 80h. This register is writable when the ACCTRL bit (D20:F0:40h, bit 31) is `0'. This allows BIOS to effectively hide the next capability registers, if necessary. This register should only be written during system initialization before the plug-and-play software has enabled any master-initiated traffic. Values of 80h implies the next capability is MSI. Values of 00h implies that the MSI capability is hidden. PWR_CAP--Power Management Capabilities Register (USB xHCI--D20:F0) Address Offset: 72h-73h Default Value: C9C2h Attribute: Size: R/W, RO 16 bits Bit Description 15:11 PME Support (PME_SUP)--R/W. This 5-bit field indicates the power states in which the function may assert PME#. The PCH xHC does not support the D1 or D2 states. For all other states, the PCH xHC is capable of generating PME#. Software should never need to modify this field. 10 D2 Support (D2_SUP)--RO. 0 = D2 State is not supported 9 D1 Support (D1_SUP)--RO. 0 = D1 State is not supported 8:6 5 Auxiliary Current (AUX_CUR)--R/W. The PCH xHC reports 375 mA maximum suspend well current required when in the D3COLD state. Device Specific Initialization (DSI)--RO. The PCH reports 0, indicating that no device-specific initialization is required. 4 Reserved 3 PME Clock (PME_CLK)--RO. The PCH reports 0, indicating that no PCI clock is required to generate PME#. 2:0 Version (VER)--RO. The PCH reports 010b, indicating that it complies with Revision 1.1 of the PCI Power Management Specification. Notes: 1. Normally, this register is read-only to report capabilities to the power management software. To report different power management capabilities, depending on the system in which the PCH is used, the write access to this register is controlled by the Access Control bit (D20:F0:40h, bit 31). The value written to this register does not affect the hardware other than changing the value returned during a read. 2. This register is modified and maintained by BIOS. 3. Reset: core well, but not D3-to-D0 warm reset. 588 Datasheet xHCI Controller Registers (D20:F0) 16.1.25 PWR_CNTL_STS--Power Management Control / Status Register (USB xHCI--D20:F0) Address Offset: 74h-75h Default Value: 0000h Bit 15 Attribute: Size: R/W, R/WC, RO 16 bits Description PME Status--R/WC. This bit is set when the PCH xHC would normally assert the PME# signal independent of the state of the PME_En bit. Writing a 1 to this bit will clear it and cause the internal PME to de-assert (if enabled). Note: This bit must be explicitly cleared by the operating system each time the operating system is loaded. This bit is not reset by Function Level Reset. 14:13 16.1.26 Data Scale--RO. Hardwired to 00b indicating it does not support the associated Data register. 12:9 Data Select--RO. Hardwired to 0000b indicating it does not support the associated Data register. 8 PME Enable (PME_En)--R/W. 0 = Disable. 1 = Enables the PCH xHC to generate an internal PME signal when PME_Status is 1. Note: This bit must be explicitly cleared by the operating system each time it is initially loaded. This bit is not reset by Function Level Reset. 7:2 Reserved 1:0 Power State--R/W. This 2-bit field is used both to determine the current power state of EHC function and to set a new power state. The definition of the field values are: 00 = D0 state 11 = D3HOT state If software attempts to write a value of 10b or 01b in to this field, the write operation must complete normally; however, the data is discarded and no state change occurs. When in the D3HOT state, the PCH must not accept accesses to the EHC memory range; but the configuration space must still be accessible. MSI_CAPID--Message Signaled Interrupt Capability ID Register (USB xHCI--D20:F0) Address Offset: 80h Default Value: 05h 16.1.27 Attribute: Size: Bit Description 7:0 Capability ID--RO. Hardwired to 05h indicating that this is the start of a MSI Capability structure. NEXT_PTR2--Next Item Pointer Register #2 (USB xHCI--D20:F0) Address Offset: 81h Default Value: 00h Function Level Reset: No Bit 7:0 Datasheet RO 8 bits Attribute: Size: RO 8 bits Description Next Item Pointer Capability--RO. This register points to the next capability. 589 xHCI Controller Registers (D20:F0) 16.1.28 MSI_MCTL--MSI Message Control Register (USB xHCI--D20:F0) Address Offset: 82h-83h Default Value: 0086h Bit 15:8 7 Description Reserved. 64-bit Address Capable (C64)--RO. Capable of generating 64-bit messages. Multiple Message Enable (MME)--RW. Indicates the number of messages the controller should assert. This device supports multiple message MSI. 3:1 Multiple Message Capable (MMC)--RO. This field is set by HW to reflect the number of Interrupters supported. The controller supports up to 8 interrupters. Encoding for number of Interrupters: 000 1 001 2 010 4 011 8 100 16 101 32 110-111 Reserved MSI Enable (MSIE)--RW. If set to 1, MSI is enabled and the traditional interrupt pins are not used to generate interrupts. If cleared to 0, MSI operation is disabled and the traditional interrupt pins are used. MSI_LMAD--MSI Lower Message Address Register (USB xHCI--D20:F0) Address Offset: 84h-87h Default Value: 00000000h Bit 31:2 1:0 16.1.30 Attribute: Size: R/W, RO 32 bits Description Lower Message Address--RW. Lower DWord of the system specified message address. Reserved. MSI_UMAD--MSI Upper Message Address Register (USB xHCI--D20:F0) Address Offset: 88h-8Bh Default Value: 00000000h Bit 31:0 590 RO, R/W 16 bits 6:4 0 16.1.29 Attribute: Size: Attribute: Size: R/W 32 bits Description Upper Message Address--RW. Upper DWord of the system specified message address. Datasheet xHCI Controller Registers (D20:F0) 16.1.31 MSI_MD--MSI Message Data Register (USB xHCI--D20:F0) Address Offset: 8Ch-8Fh Default Value: 00000000h Attribute: Size: Bit 31:16 15:0 16.1.32 Description Reserved. Data--R/W. This 16-bit field is programmed by system software if MSI is enabled. Its content is driven onto the lower word (PCI AD[15:0]) during the data phase of the MSI memory write transaction. U2OCM1 - XHCI USB2 Overcurrent Mapping Register1 (USB xHCI--D20:F0) Address Offset: C0-C3h Default Value: 00000000h Attribute: Size: Description 31:24 OC3 Mapping Each bit position maps OC3# to a set of ports as follows: The OC3# pin is ganged to the overcurrent signal of each port that has its corresponding bit set. It is software responsibility to ensure that a given port`s bit map is set only for one OC pin. 23:16 15:8 12 9 8 3 2 1 0 13 12 9 8 3 2 1 0 OC1 Mapping Each bit position maps OC1# to a set of ports as follows: The OC1# pin is ganged to the overcurrent signal of each port that has its corresponding bit set. It is software responsibility to ensure that a given port`s bit map is set only for one OC pin. Port 7:0 13 OC2 Mapping Each bit position maps OC2# to a set of ports as follows: The OC2# pin is ganged to the overcurrent signal of each port that has its corresponding bit set. It is software responsibility to ensure that a given port`s bit map is set only for one OC pin. Port 13 12 9 8 3 2 1 0 OC0 Mapping Each bit position maps OC0# to a set of ports as follows: The OC0# pin is ganged to the overcurrent signal of each port that has its corresponding bit set. It is software responsibility to ensure that a given port`s bit map is set only for one OC pin. Port 13 12 9 8 3 2 1 0 U2OCM2 - XHCI USB2 Overcurrent Mapping Register 2 (USB xHCI--D20:F0) Address Offset: C4-C7h Default Value: 00000000h Attribute: Size: Bit R/W, RO 32 bits Description 31:30 Reserved 29:24 OC7 Mapping Each bit position maps OC7 to a set of ports as follows: The OC7 pin is ganged to the overcurrent signal of each port that has its corresponding bit set. It is software responsibility to ensure that a given port`s bit map is set only for one OC pin. Port Datasheet R/W, RO 32 bits Bit Port 16.1.33 R/W 32 bits 11 10 7 6 5 4 591 xHCI Controller Registers (D20:F0) Bit Description 23:22 Reserved 21:16 OC6 Mapping Each bit position maps OC6 to a set of ports as follows: The OC6 pin is ganged to the overcurrent signal of each port that has its corresponding bit set. It is software responsibility to ensure that a given port`s bit map is set only for one OC pin. Port 15:14 13:8 10 7 6 5 4 Reserved OC5 Mapping Each bit position maps OC5 to a set of ports as follows: The OC5 pin is ganged to the overcurrent signal of each port that has its corresponding bit set. It is software responsibility to ensure that a given port`s bit map is set only for one OC pin. Port 11 10 7 6 5 4 7:6 Reserved 5:0 OC4 Mapping Each bit position maps OC4 to a set of ports as follows: The OC4 pin is ganged to the overcurrent signal of each port that has its corresponding bit set. It is software responsibility to ensure that a given port`s bit map is set only for one OC pin. Port 16.1.34 11 11 10 7 6 5 4 U3OCM1 - XHCI USB3 Overcurrent Pin Mapping 1 (USB xHCI--D20:F0) Address Offset: C8-CBh Default Value: 00000000h Attribute: Size: Bit Description 31:30 Reserved 29:24 OC3 Mapping Each bit position maps OC3to a set of ports as follows: The OC3 pin is ganged to the overcurrent signal of each port that has its corresponding bit set. It is software responsibility to ensure that a given port`s bit map is set only for one OC pin. Port 6 5 4 3 2 1 23:22 Reserved 21:16 OC2 Mapping Each bit position maps OC2 to a set of ports as follows: The OC2 pin is ganged to the overcurrent signal of each port that has its corresponding bit set. It is software responsibility to ensure that a given port`s bit map is set only for one OC pin. Port 15:14 13:8 6 5 4 3 2 1 Reserved OC1 Mapping Each bit position maps OC1 to a set of ports as follows: The OC1 pin is ganged to the overcurrent signal of each port that has its corresponding bit set. It is software responsibility to ensure that a given port`s bit map is set only for one OC pin. Port 6 5 4 3 2 1 7:6 Reserved 5:0 OC0 Mapping Each bit position maps OC0 to a set of ports as follows: The OC0 pin is ganged to the overcurrent signal of each port that has its corresponding bit set. It is software responsibility to ensure that a given port`s bit map is set only for one OC pin. Port 592 R/W, RO 32 bits 6 5 4 3 2 1 Datasheet xHCI Controller Registers (D20:F0) 16.1.35 U3OCM2 - XHCI USB3 Overcurrent Pin Mapping 2 (USB xHCI--D20:F0) Address Offset: CC-CFh Default Value: 00000000h Attribute: Size: Bit Description 31:30 Reserved 29:24 OC7 Mapping Each bit position maps OC7 to a set of ports as follows: The OC7 pin is ganged to the overcurrent signal of each port that has its corresponding bit set. It is software responsibility to ensure that a given port`s bit map is set only for one OC pin. Port 5 4 3 2 1 Reserved 21:16 OC6 Mapping Each bit position maps OC6 to a set of ports as follows: The OC6 pin is ganged to the overcurrent signal of each port that has its corresponding bit set. It is software responsibility to ensure that a given port`s bit map is set only for one OC pin. 15:14 13:8 6 5 4 3 2 1 Reserved OC5 Mapping Each bit position maps OC5 to a set of ports as follows: The OC5 pin is ganged to the overcurrent signal of each port that has its corresponding bit set. It is software responsibility to ensure that a given port`s bit map is set only for one OC pin. Port 6 5 4 3 2 1 7:6 Reserved 5:0 OC4 Mapping Each bit position maps OC4 to a set of ports as follows: The OC4 pin is ganged to the overcurrent signal of each port that has its corresponding bit set. It is software responsibility to ensure that a given port`s bit map is set only for one OC pin. Port 6 5 4 3 2 1 XUSB2PR--xHC USB 2.0 Port Routing Register (USB xHCI--D20:F0) Address Offset: Default Value: Note: 6 23:22 Port 16.1.36 R/W, RO 32 bits D0-D3h 00000000h Attribute: Size: R/W, RO 32 bits Bits 3:0 are located in the Suspend Well. Bit 31:15 14:0 Description Reserved. USB 2.0 Host Controller Selector (USB2HCSEL)--R/W. Maps a USB 2.0 port to the xHC or EHC #1 host controller. When set to 0, this bit routes all the corresponding USB 2.0 port pins to the EHCI controller (D29:F0) and RMH #1. The USB 2.0 port is masked from the xHC and the USB 2.0 port's OC pin is routed to the EHCI controller (D29:F0). When set to 1, this bit routes all the corresponding USB 2.0 pins to the xHC controller. The USB 2.0 port is masked from the EHC and the USB 2.0 port's OC pin is routed to the xHC controller (D20:F0). Port to bit mapping is in one-hot encoding; that is, bit 0 controls port 1 and so on. Bit 0 = USB 2.0 Port 0 .... Bit 13 = USB 2.0 Port 13 Datasheet 593 xHCI Controller Registers (D20:F0) 16.1.37 XUSB2PRM--xHC USB 2.0 Port Routing Mask Register (USB xHCI--D20:F0) Address Offset: Default Value: Note: D4-D7h 00000000h Attribute: Size: RO, R/WL 32 bits The R/WL property of this register is controlled by the ACCTRL bit (D20:F0:40h, bit 31). Bit Description 31:15 14:0 Reserved. USB 2.0 Host Controller Selector Mask (USB2HCSELM)--R/W. This bit field allows the BIOS to communicate to the OS which USB 2.0 ports can be switched from the EHC controller to the xHC controller. When set to 1, the OS may switch the USB 2.0 port between the EHCI and xHCI host controllers by modifying the corresponding USB2HCSEL bit (D20:F0:D0h, bit 3:0). When set to 0, The OS shall not modify the corresponding USB2HCSEL bit. Port to bit mapping is in one-hot encoding: that is, bit 0 controls port 1 and so on. Bit 0 = USB 2.0 Port 0 .... Bit 13 = USB 2.0 Port 13 16.1.38 USB3_PSSEN--USB 3.0 Port SuperSpeed Enable Register (USB xHCI--D20:F0) Address Offset: Default Value: Note: D8h-dBh 00000000h Attribute: Size: RO, R/W 32 bits Bits 3:0 are located in the Suspend Well. Bit 31:6 5:0 Description Reserved. USB 3.0 Port SuperSpeed Enable (USB3PSSEN)--R/W. This field controls whether SuperSpeed capability is enabled for a given USB 3.0 port. When set to 1, this bit enables the SuperSpeed terminations and allows the xHC to view the SuperSpeed connections on the USB port. Enables PORTSC to see the connects on the ports. When set to 0, the port's SuperSpeed capability is not visible to the xHC. Bit 0 = USB 3.0 Port 1 Bit 1 = USB 3.0 Port 2 Bit 2 = USB 3.0 Port 3 Bit 3 = USB 3.0 Port 4 Bit 4 = USB 3.0 Port 5 Bit 5 = USB 3.0 Port 6 594 Datasheet xHCI Controller Registers (D20:F0) 16.1.39 USB3PRM--USB 3.0 Port Routing Mask Register (USB xHCI--D20:F0) Address Offset: DC-DFh Default Value: 00000000h Power Well: Core Note: Attribute: Size: R/WL, RO 32 bits The R/WL property of this register is controlled by the ACCTRL bit (D20:F0:40h, bit 31). Bit 31:6 5:0 Description Reserved. USB 2.0 Host Controller Selector Mask (USB2HCSELM)--R/W. This bit field allows the BIOS to communicate to the OS which USB 3.0 ports can have the SuperSpeed capabilities enabled. When set to 1, the OS may enable or disable the SuperSpeed capabilities by modifying the corresponding USB3PSSEN bit (D20:F0:D8h, bit 3:0). When set to 0, the OS shall not modify the corresponding USB3PSSEN bit. Bit 0 = USB 3.0 Port 1 Bit 1 = USB 3.0 Port 2 Bit 2 = USB 3.0 Port 3 Bit 3 = USB 3.0 Port 4 Bit 4 = USB 3.0 Port 5 Bit 5 = USB 3.0 Port 6 16.1.40 USB2PDO--xHCI USB Port Disable Override Register (USB xHCI--D20:F0) Address Offset: E4-E7h Default Value: 00000000h Power Well: Suspend Bit 31:15 14:0 Attribute: Size: R/WO 32 bits Description Reserved. xHCI USB Port Disable Override (XUSBPDO)--R/WO. 0 = Allows corresponding USB port to report a Device Connection to the xHC. 1 = Prevents the corresponding USB port from reporting a Device Connection to the xHC. Port to bit mapping is in one-hot encoding; that is, bit 0 controls port 1 and so on. Bit 0 = USB 2.0 Port 0 .... Bit 13 = USB 2.0 Port 13 Datasheet 595 xHCI Controller Registers (D20:F0) 16.1.41 USB3PDO--USB3 Port Disable Override (USB xHCI--D20:F0) Address Offset: E8-EBh Default Value: 00000000h Power Well: Suspend Bit 31:15 14:0 Attribute: Size: R/WO 32 bits Description Reserved. xHCI USB Port Disable Override (XUSBPDO)--R/WO. 0 = Allows corresponding USB port to report a Device Connection to the xHC. 1 = Prevents the corresponding USB port from reporting a Device Connection to the xHC. Bit 0 = USB 3.0 Port 1 Bit 1 = USB 3.0 Port 2 Bit 2 = USB 3.0 Port 3 Bit 3 = USB 3.0 Port 4 Bit 4 = USB 3.0 Port 5 Bit 5 = USB 3.0 Port 6 16.2 Memory-Mapped I/O Registers The xHCI memory-mapped I/O space is composed of two sets of registers: Capability Registers and Operational Registers. Note: The PCH xHC controller will not accept locked memory transactions (neither reads nor writes) as a target. The locked transactions should not be forwarded to PCI as the address space is known to be allocated to USB. Attempting to access the xHCI controller Memory-Mapped I/O space using locked memory transactions will result in undefined behavior. Note: When the xHCI function is in the D3 PCIe power state, accesses to the xHCI memory range are ignored and result in a master abort. Similarly, if the Memory Space Enable (MSE) bit (D20:F0:04h, bit 1) is not set in the Command register in configuration space, the memory range will not be decoded by the PCH xHC. If the MSE bit is not set, the PCH must default to allowing any memory accesses for the range specified in the BAR to go to PCI. This is because the range may not be valid and, therefore, the cycle must be made available to any other targets that may be currently using that range. 596 Datasheet xHCI Controller Registers (D20:F0) 16.2.1 Host Controller Capability Registers These registers specify the limits, restrictions and capabilities of the host controller implementation. Table 16-1. Enhanced Host Controller Capability Registers MEM_BASE + Offset Power Well Mnemonic Register Default Type 80h RW/L 0100h RO 00h Core CAPLENGTH Capabilities Registers Length 02h-03h Core HCIVERSION Host Controller Interface Version Number 04h-07h Core HCSPARAMS1 Host Controller Structural Parameters #1 15000820h RW/L 08h-0Bh Core HCSPARAMS2 Host Controller Structural Parameters #2 84000054h RW/L 0Ch-0Fh Core HCSPARAMS3 10h-13h Core HCCPARAMS 14h-17h Core dBOFF 18h-1Bh Core RTSOFF 16.2.1.1 00040001h RW/L 200071E9h RW/L Doorbell Offset 0000C000h RO Runtime Register Space Offset 00001000h RO CAPLENGTH--Capability Registers Length Register Offset: Default Value: 16.2.1.2 Host Controller Structural Parameters #3 Host Controller Capability Parameters MEM_BASE + 00h 80h Description 7:0 Capability Register Length Value--RW. This register is used as an offset to add to the Memory Base Register (D20:F0:10h) to find the beginning of the Operational Register Space. This register is modified and maintained by BIOS. HCIVERSION--Host Controller Interface Version Number Register MEM_BASE + 02h-03h 0100h Bit 15:0 Attribute: Size: RO 16 bits Description Host Controller Interface Version Number--RO. This is a two-byte register containing a BCD encoding of the version number of interface that this host controller interface conforms to. HCSPARAMS1--Host Controller Structural Parameters #1 Register Offset: Default Value: Datasheet RW/L 8 bits Bit Offset: Default Value: 16.2.1.3 Attribute: Size: MEM_BASE + 04h-07h 15000820h Attribute: Size: RW/L 32 bits Bit Description 31:24 Number of Ports (MaxPorts)--RW/L. This field specifies the number of physical downstream ports implemented on this host controller. The value of this field determines how many port registers are addressable in the Operational Register Space. Default value = 15h 23:19 Reserved 18:8 Number of Interrupters (MaxIntrs)--RW/L. This field specifies the number of interrupters implemented on this host controller. Each interrupter is allocated to a vector of MSI and controls its generation and moderation. 7:0 Number of Device Slots (MaxSlots)--RW/L. This field specifies the number of Device Context Structures and Doorbell Array entries this host controller can support. Valid values are in the range of 1 to 255. 597 xHCI Controller Registers (D20:F0) 16.2.1.4 HCSPARAMS2--Host Controller Structural Parameters #2 Register Offset: Default Value: MEM_BASE + 08h-0Bh 84000054h Bit 31:27 26 25:8 16.2.1.5 Attribute: Size: RW/L 32 bits Description Max Scratchpad Buffers (MaxScratchpadBufs)--RW/L. Indicates the number of Scratchpad Buffers system software shall reserve for the xHC. Scratchpad Restore (SPR)--RW/L. 0 = Indicates the Scratchpad buffer space may be freed and reallocated between power events. 1 = Indicates that the xHC requires the integrity of the Scratchpad buffer space to be maintained across power events. Reserved. 7:4 Event Ring Segment Table Max (ERSTMax)--RW/L. This field determines the maximum value supported by the Event Ring Segment Table Base Size registers. 3:0 Isochronous Scheduling Threshold (IST)--RW/L. This field indicates to system software the minimum distance (in time) that it is required to stay ahead of the xHC while adding TRBs, in order to have the xHC process them at the correct time. The value is specified in the number if frames/ microframes. If bit [3] of IST is cleared to 0b, software can add a TRB no later than IST [2:0] microframes before that TRB is scheduled to be executed. If bit [3] of IST is set to 1b, software can add a TRB no later than IST[2:0] frames before that TRB is scheduled to be executed. HCSPARAMS3--Host Controller Structural Parameters #3 Register Offset: Default Value: MEM_BASE + 0Ch-0Fh 00040001h Attribute: Size: RW/L 32 bits Bit Description 31:16 U2 Device Exit Latency (U2DEL)--RW/L. Indicates the worst case latency to transition from U2 to U0. Applies to all root hub ports. The following are permissible values: Value Description 00h Zero 01h Less than 1 s 02h Less than 2 s ... 0Bh-FFh 15:8 7:0 Reserved Reserved. U1 Device Exit Latency (U1DEL)--RW/L. Worst case latency to transition a root hub Port Link State (PLS) from U1 to U0. Applies to all root hub ports. The following are permissible values: Value Description 00h Zero 01h Less than 1 s 02h Less than 2 s ... 0800h-FFFFh 598 Reserved Datasheet xHCI Controller Registers (D20:F0) 16.2.1.6 HCCPARAMS--Host Controller Capability Parameters Register Offset: Default Value: MEM_BASE + 10h-13h 200071E9h Bit Description xHCI Extended Capabilities Pointer (xECP)--RW/L This field indicates the existence of a capabilities list. The value of this field indicates a relative offset, in 32-bit words, from Base to the beginning of the first extended capability. 15:12 Maximum Primary Stream Array Size (MaxPSASize)--RW/L. This fields identifies the maximum size Primary Stream Array that the xHC supports. The Primary Stream Array size = 2MaxPSASize+1. Valid MaxPSASize values are 1 to 15. 11 Reserved. 10 Stopped EDLTA Capability (SEC)--RW/L. This flag indicates that the host controller implementation Stream Context support a Stopped EDLTA field. Stopped Short Packet Capability (SPC)--RW/L. This flag indicates that the host controller implementation is capable of generating a Stopped - Short Packet Completion Code. 8 Reserved. 7 No Secondary SID Support (NSS)--RW/L. Hardwired to `0' indicating Secondary Stream ID decoding is supported. 6 Latency Tolerance Messaging Capability (LTC)--RW/L. 0 = Latency Tolerance Messaging is not supported. 1 = Latency Tolerance Messaging is supported 5 Light HC Reset Capability (LHRC)--RW/L. 0 = Light Host Controller Reset is not supported. 1 = Light Host Controller Reset is supported 4 Port Indicators (PIND)--RW/L. This bit indicates whether the xHC root hub ports support port indicator control. When this bit is a `1', the port status and control registers include a read/writeable field for controlling the state of the port indicator. 3 Port Power Control (PPC)--RO. This bit indicates whether the host controller implementation includes port power control. A `1' in this bit indicates the ports have port power switches. A `0' in this bit indicates the port do not have port power switches. 2 Context Size (CSZ)--RW/L. If this bit is set to `1', then the xHC uses 64 byte Context data structures. If this bit is cleared to `0', then the xHC uses 32 byte Context data structures. Note: This flag does not apply to Stream Contexts. 1 BW Negotiation Capability (BNC)--RW/L. 0 = Not capable of BW Negotiation. 1 = Capable of BW Negotiation. 0 64-bit Addressing Capability (AC64)--RW/L. This bit documents the addressing range capability of the xHC. The value of this flag determines whether the xHC has implemented the high order 32 bits of 64-bit register and data structure pointer fields. Values for this flag have the following interpretation: 0 = Supports 32-bit address memory pointers 1 = Supports 64-bit address memory pointers If 32-bit address memory pointers are implemented, the xHC shall ignore the high order 32 bits of 64-bit data structure pointer fields, and system software shall ignore the high order 32 bits of 64-bit xHC registers. dBOFF--Doorbell Offset Register Offset: Default Value: MEM_BASE + 14h-17h 0000C000h Attribute: Size: RO 32 bits Bit Description 31:2 Doorbell Array Offset--RO. This field defines the DWord offset of the Doorbell Array base address from the Base (that is, the base address of the xHCI Capability register address space). 1:0 Datasheet RW/L 32 bits 31:16 9 16.2.1.7 Attribute: Size: Reserved. 599 xHCI Controller Registers (D20:F0) 16.2.1.8 RTSOFF--Runtime Register Space Offset Register Offset: Default Value: MEM_BASE + 18h-1Bh 00001000h Bit 31:2 1:0 16.2.2 Attribute: Size: RO 32 bits Description Runtime Register Space Offset--RO. This field defines the 32-byte offset of the xHCI Runtime Registers from the Base. That is, Runtime Register Base Address = Base + Runtime Register Set Offset. Reserved. Host Controller Operational Registers This section defines the xHC operational registers. These registers are located after the capabilities registers. The operational register base must be DWord-aligned and is calculated by adding the value in the first capabilities register (CAPLENGTH) to the base address of the xHC register address space (MEM_BASE). Since CAPLENGTH is always 80h, Table 16-2 already accounts for this offset. All registers are 32 bits in length. Table 16-2. Enhanced Host Controller Operational Register Address Map MEM_BASE + Offset Power Well Mnemonic 80h-83h Core USB_CMD USB Command 00000000h R/W, RO 84h-87h Core USB_STS USB Status 00000001h R/WC, RO 88h-8Bh Core PAGESIZE Page Size 00000001h RO 94h-97h Core DNCTRL Device Notification Control 00000000h R/W, RO Default Type 98h-9Bh Core CRCRL Command Ring Control Low 00000000h R/W, RO 9Ch-9Fh Core CRCRH Command Ring Control High 00000000h R/W, RO B0h-B3h Core DCBAAPL Device Context Base Address Array Pointer Low 00000000h R/W, RO B4h-B7h Core DCBAAPH Device Context Base Address Array Pointer High 00000000h R/W, RO B8h-BBh Core CONFIG 480h, 490h, 4A0h, 4B0h, 4C0h, 4D0h, 4E0h, 4F0h, 500h, 510h, 520h, 530h, 540h, 550h, 560h Multiple PORTSCNUSB2 484h, 494h, 4A4h, 4B4h, 4C4h, 4D4h, 4E4h, 4F4h, 504h, 514h, 524h, 534h, 544h, 554h, 564h Multiple PORTPMSCNUSB2 570h, 580h, 590h, 5A0h, 5B0h, 5C0h Multiple PORTSCNUSB3 574h, 584h, 594h, 5A4h, 5B4h, 5C4h Suspend PORTPMSCN 578h, 588h, 598h, 5A8h, 5B8h, 5C8h Core PORTLIX Note: 600 Register Name Configure 00000000h R/W, RO Port N Status and Control USB2 000002A0h R/W, R/WC, RO, R/WO, R/ WC Port N Power Management Status and Control USB2 00000000h R/W, RO Port N Status and Control USB3 000002A0h R/W, RO Port N Power Management Status and Control USB3 00000000h R/W, RO USB 3.0 Port Link Info 00000000h RO Software must read and write these registers using only DWord accesses. Datasheet xHCI Controller Registers (D20:F0) 16.2.2.1 USB_CMD--USB Command Register Offset: Default Value: MEM_BASE + 80h-83h 00000000h Bit 31:12 Attribute: Size: R/W, RO 32 bits Description Reserved. 11 Enable U3 MFINDEX Stop (EU3S)--R/W. When set to 1b, the xHC may stop the MFINDEX counting action if all Root Hub ports are in the U3, Disconnected, Disabled, or Powered-off state. When cleared to 0b, the xHC may stop the MFINDEX counting action if all Root Hub ports are in the Disconnected, Disabled, or Powered-off state. 10 Enable Wrap Event (EWE)--R/W. When set to 1b, the xHC shall generate a MFINDEX Wrap Event every time the MFINDEX register transitions from 03FFFh to 0. When cleared to 0b, no MFINDEX Wrap Events are generated. 9 Controller Restore State (CRS)--R/W. When set to 1b, MEM_BASE+80h:bit 0= 0b, and MEM_BASE+80h:bit 8 = 1b, the xHC shall perform a Restore State operation and restore its internal state. When set to 1b and MEM_BASE+80h:bit 0= 1b or MEM_BASE+80h:bit 8 = 0b, or when cleared to `0', no Restore State operation shall be performed. Note: 8 Controller Save State (CSS)--R/W. When written by software with 1b and MEM_BASE+80h:bit 0= 0b, the xHC shall save any internal state that will be restored by a subsequent Restore State operation. When written by software with 1b and MEM_BASE+80h:bit 0= 1b, or written with `0', no Save State operation shall be performed. Note: 7 This flag always returns `0' when read. Light Host Controller Reset (LHCRST)--R/W. If the Light HC Reset Capability (LHRC) bit (MEM_BASE=10h:bit 5) is 1b, then setting this bit to 1b allows the driver to reset the xHC without affecting the state of the ports. A system software read of this bit as 0b indicates the Light Host Controller Reset has completed and it is safe for software to re-initialize the xHC. A software read of this bit as a 1b indicates the Light Host Controller Reset has not yet completed. Note: 6:4 This flag always returns `0' when read. If Light HC Reset Capability is not implemented, a read of this flag will always return a 0b. Reserved. 3 Host System Error Enable (HSEE)--R/W. When this bit is set to 1b, and the HSE bit (MEM_BASE+84h:bit 2) is set to 1b, the xHC shall assert out-of-band error signaling to the host. The signaling is acknowledged by software clearing the HSE bit. 2 Interrupter Enable (INTE)--R/W. This bit provides system software with a means of enabling or disabling the host system interrupts generated by interrupters. When this bit is set to 1b, then Interrupter host system interrupt generation is allowed, such that the xHC shall issue an interrupt at the next interrupt threshold if the host system interrupt mechanism (such that MSI, MSIX, and so on) is enabled. The interrupt is acknowledged by a host system interrupt specific mechanism. 1 Host Controller Reset (HCRST)--R/W. This control bit is used by software to reset the host controller. When software sets this bit to 1b, the Host Controller resets its internal pipelines, timers, counters, state machines, and so on to their initial value. Any transaction currently in progress on USB is immediately terminated. A USB reset is not driven on downstream ports. PCI Configuration registers are not affected by this reset. All operational registers, including port registers and port state machines are set to their initial values. Notes: 1. This bit is cleared to 0b by the Host Controller when the reset process is complete. Software cannot terminate the reset process early by writing a 0b to this bit and shall not write any xHC Operational or Runtime registers while HCRST is set to 1b. 2. Software shall not set this bit to 1b when the HCHalted (HCH) bit (MEM_BASE+84h:bit 0) is set to 0b. Attempting to reset an actively running host controller will result in undefined behavior. Datasheet 601 xHCI Controller Registers (D20:F0) 16.2.2.2 Bit Description 0 Run/Stop (R/S)--R/W. When set to 1b, the xHC proceeds with execution of the schedule. The xHC continues execution as long as this bit is set to 1b. When this bit is cleared to 0b, the xHC completes the current and any actively pipelined transactions on the USB and then halts. The xHC shall halt within 16 microframes after software clears the Run/ Stop bit. The HCHalted (HCH) bit (MEM_BASE+84h:bit 0) indicates when the xHC has finished its pending pipelined transactions and has entered the stopped state. Software shall not write a `1' to this flag unless the xHC is in the Halted state (that is, HCH in the USBSTS register is `1'); doing so will yield undefined results. USB_STS--USB Status Register Offset: Default Value: MEM_BASE + 84h-87h 00000001h Attribute: Size: R/WC, RO 32 bits This register indicates pending interrupts and various states of the Host controller. The status resulting from a transaction on the serial bus is not indicated in this register. See the Interrupts description in Section 4 of the xHCI specification for additional information concerning interrupt conditions. Note: For the writable bits, software must write a 1 to clear bits that are set. Writing a 0 has no effect. Bit 31:13 Description Reserved. 12 Host Controller Error (HCE) RO. This flag shall be set to indicate that an internal error condition has been detected which requires software to reset and re-initialize the xHC. 0 = No internal xHC error conditions exist. 1 = Internal xHC error condition exists. 11 Controller Not Ready (CNR) RO. 0 = Ready 1 = Not Ready Software shall not write any Doorbell or Operational register of the xHC, other than the USBSTS register, until CNR = 0b. This flag is set by the xHC after a Hardware Reset and cleared when the xHC is ready to begin accepting register writes. This flag shall remain cleared (0b) until the next Chip Hardware Reset. 10 Save/Restore Error (SRE) R/WC. If an error occurs during a Save or Restore operation this bit shall be set to 1b. This bit shall be cleared to 0b when a Save or Restore operation is initiated or when written with 1b. 9 Restore State Status (RSS) RO. When the Controller Restore State (CRS) flag in the USB_CMD register is written with 1b this bit shall be set to 1b and remain set while the xHC restores its internal state. Note: 8 Note: 7:5 4 602 When the Restore State operation is complete, this bit shall be cleared to 0b. Save State Status (SSS) RO. When the Controller Save State (CSS) flag in the USB_CMD register is written with 1b this bit shall be set to 1b and remain set while the xHC saves its internal state. When the Save State operation is complete, this bit shall be cleared to 0b. Reserved. Port Change Detect (PCD)--R/WC. This bit is allowed to be maintained in the Auxiliary power well. Alternatively, it is also acceptable that on a D3 to D0 transition of the xHC, this bit is loaded with the OR of all of the PORTSC change bits (including: Force port resume, overcurrent change, enable/ disable change and connect status change). Regardless of the implementation, when this bit is readable (that is, in the D0 state), it must provide a valid view of the Port Status registers. 0 = No change bit transition from a 0 to 1 or No Force Port Resume bit transition from 0 to 1 as a result of a J-K transition detected on a suspended port. 1 = The Host controller sets this bit to 1 when any port for which the Port Owner bit is set to 0 has a change bit transition from a 0 to 1 or a Force Port Resume bit transition from 0 to 1 as a result of a J-K transition detected on a suspended port. Datasheet xHCI Controller Registers (D20:F0) 16.2.2.3 Bit Description 3 Event Interrupt (EINT)--R/WC. The xHC sets this bit to 1b when the Interrupt Pending (IP) bit of any Interrupter is transitions from 0b to 1b. Software that uses EINT shall clear it prior to clearing any IP flags. A race condition will occur if software clears the IP flags then clears the EINT flag, and between the operations another IP `0' to '1' transition occurs. In this case the new IP transition will be lost. 2 Host System Error (HSE)--R/WC. The xHC sets this bit to 1b when a serious error is detected, either internal to the xHC or during a host system access involving the xHC module. Conditions that set this bit to `1' include PCI Parity error, PCI Master Abort, and PCI Target Abort. When this error occurs, the xHC clears the Run/Stop (R/S) bit in the USB_CMD register to prevent further execution of the scheduled TDs. If the HSEE bit in the USB_CMD register is 1b, the xHC shall also assert out-ofband error signaling to the host. 1 Reserved. 0 HCHalted (HCH)--RO. This bit is a `0' whenever the Run/Stop (R/S) bit is set to 1b. The xHC sets this bit to 1b after it has stopped executing as a result of the Run/Stop (R/S) bit being cleared to 0b, either by software or by the xHC hardware (such as internal error). If this bit is set to1b, then SOFs, microSOFs, or Isochronous Timestamp Packets (ITP) shall not be generated by the xHC. PAGESIZE--Page Size Register Offset: Default Value: MEM_BASE + 88h-8Bh 00000001h Bit 31:16 15:0 16.2.2.4 RO 32 bits Description Reserved Page Size--RO. Hardwired to 1h to indicate support for 4k byte page sizes. DNCTRL--Device Notification Control Register Offset: Default Value: Bit 31:16 15:0 Datasheet Attribute: Size: MEM_BASE + 94h-97h 00000000h Attribute: Size: R/W, RO 32 bits Description Reserved. Notification Enable--R/W. When a Notification Enable bit is set, a Device Notification Event will be generated when a Device Notification Transaction Packet is received with the matching value in the Notification Type field. For example, setting N1 to `1' enables Device Notification Event generation if a Device Notification TP is received with its Notification Type field set to `1' (FUNCTION_WAKE), and so on. Refer to the USB 3.0 Specification for more information on Notification Types. 603 xHCI Controller Registers (D20:F0) 16.2.2.5 CRCRL--Command Ring Control Low Register Offset: Default Value: Bit 31:6 MEM_BASE + 98h-9Bh 00000000h Attribute: Size: R/W, RO 32 bits Description Command Ring Pointer--R/W. This field defines low order bits of the initial value of the 64-bit Command Ring Dequeue Pointer. Notes: 1. Writes to this field are ignored when Command Ring Running bit (CRR) = 1b. 2. If the CRCR register is written while the Command Ring is stopped (CRR = 0b), the value of this field shall be used to fetch the first Command TRB the next time the Host Controller Doorbell register is written with the dB Reason field set to Host Controller Command. 3. If the CRCR register is not written while the Command Ring is stopped (CRR = 0b), then the Command Ring shall begin fetching Command TRBs at the current value of the internal xHC Command Ring Dequeue Pointer. 4. Reading this field always returns 0b. 5:4 Reserved. 3 Command Ring Running (CRR)--RO. This bit is set to 1b if the Run/Stop (R/S) bit is 1b and the Host Controller Doorbell register is written with the dB Reason field set to Host Controller Command. It is cleared to 0b when the Command Ring is stopped after writing a 1b to the Command Stop (CS) or Command Abort (CA) bits, or if the R/S bit is cleared to 0b. 2 Command Abort (CA)--R/W. Writing a 1b to this bit shall immediately terminate the currently executing command, stop the Command Ring, and generate a Command Completion Event with the Completion Code set to Command Ring Stopped. The next write to the Host Controller Doorbell with dB Reason field set to Host Controller Command shall restart the Command Ring operation. Notes: 1. Writes to this flag are ignored by the xHC if Command Ring Running (CRR) = 0b. 2. Reading this bit always returns 0b. 1 Command Stop (CS)--R/W. Writing a 1b to this bit shall stop the operation of the Command Ring after the completion of the currently executing command, and generate a Command Completion Event with the Completion Code set to Command Ring Stopped and the Command TRB Pointer set to the current value of the Command Ring Dequeue Pointer. The next write to the Host Controller Doorbell with dB Reason field set to Host Controller Command shall restart the Command Ring operation. Notes: 1. Writes to this flag are ignored by the xHC if Command Ring Running (CRR) bit = 0b. 2. Reading this bit always returns 0b. 0 Ring Cycle State (RCS)--R/W. This bit identifies the value of the xHC Consumer Cycle State (CCS) flag for the TRB referenced by the Command Ring Pointer. Notes: 1. Writes to this bit are ignored when the Command Ring Running (CRR) bit = 1b. 2. If the CRCR register is written while the Command Ring is stopped (CCR = 0b), then the value of this flag shall be used to fetch the first Command TRB the next time the Host Controller Doorbell register is written with the dB Reason field set to Host Controller Command. 3. If the CRCR register is not written while the Command Ring is stopped (CCR = 0b), then the Command Ring will begin fetching Command TRBs using the current value of the internal Command Ring CCS flag. 4. Reading this flag always returns 0b. Notes: 1. Setting the Command Stop (CS) or Command Abort (CA) flags while CRR = 1b shall generate a Command Ring Stopped Command Completion Event. 2. Setting both the Command Stop (CS) and Command Abort (CA) flags with a single write to the CRCR register while CRR = `1' shall be interpreted as a Command Abort (CA) by the xHC. 3. The values of the internal xHC Command Ring CCS flag and Dequeue Pointer are undefined after hardware reset, so these fields shall be initialized before setting USB_CMD Run/Stop (R/S) bit (MEM_BASE+80:bit 0) to 1b. 604 Datasheet xHCI Controller Registers (D20:F0) 16.2.2.6 CRCRH--Command Ring Control High Register Offset: Default Value: MEM_BASE + 9Ch-9Fh 00000000h Bit 31:0 Attribute: Size: R/W, RO 32 bits Description Command Ring Pointer--R/W. This field defines high order bits of the initial value of the 64-bit Command Ring Dequeue Pointer. Notes: 1. Writes to this field are ignored when Command Ring Running bit (CRR) = 1b. 2. If the CRCR register is written while the Command Ring is stopped (CRR = 0b), the value of this field shall be used to fetch the first Command TRB the next time the Host Controller Doorbell register is written with the dB Reason field set to Host Controller Command. 3. If the CRCR register is not written while the Command Ring is stopped (CRR = 0b), then the Command Ring shall begin fetching Command TRBs at the current value of the internal xHC Command Ring Dequeue Pointer. 4. Reading this field always returns 0b. 16.2.2.7 DCBAAPL--Device Context Base Address Array Pointer Low Register Offset: Default Value: Description Device Context Base Address Array Pointer--R/W. This field defines low order bits of the 64-bit base address of the Device Context Pointer Array table (a table of address pointers that reference Device Context structures for the devices attached to the host.) Reserved. DCBAAPH--Device Context Base Address Array Pointer High Register MEM_BASE + B4h-B7h 00000000h Attribute: Size: R/W, RO 32 bits Bit Description 31:0 Device Context Base Address Array Pointer--R/W. This field defines high order bits of the 64-bit base address of the Device Context Pointer Array table (a table of address pointers that reference Device Context structures for the devices attached to the host.) CONFIG--Configure Register Offset: Default Value: Bit 31:8 7:0 Datasheet R/W, RO 32 bits Bit Offset: Default Value: 16.2.2.9 Attribute: Size: 31:6 5:0 16.2.2.8 MEM_BASE + B0h-B3h 00000000h MEM_BASE + B8h-BBh 00000000h Attribute: Size: R/W, RO 32 bits Description Reserved. Max Device Slots Enabled (MaxSlotsEn)--R/W. This field specifies the maximum number of enabled Device Slots. Valid values are in the range of 0h to 20h. Enabled Devices Slots are allocated contiguously (such that a value of 16 specifies that Device Slots 1 to 16 are active.) A value of `0' disables all Device Slots. A disabled Device Slot shall not respond to Doorbell Register references. Note: This field shall not be modified if the xHC is running (Run/Stop (R/S) = `1'). 605 xHCI Controller Registers (D20:F0) 16.2.2.10 PORTSCNUSB2--Port N Status and Control USB2 Register Offset: There are 15 USB2 PORTSC registers at offsets: 480h, 490h, 4A0h, 4B0h, 4C0h, 4D0h, 4E0h, 4F0h, 500h, 510h, 520h, 530h, 540h, 550h, 560h Attribute: R/W, R/WC, RO, R/WO Default Value: 000002A0h Size: 32 bits A host controller must implement one or more port registers. Software uses the N_Port information from the Structural Parameters Register to determine how many ports need to be serviced. All ports have the structure defined below. Software must not write to unreported Port Status and Control Registers. This register is in the suspend power well. It is only reset by hardware when the suspend power is initially applied or in response to a host controller reset. The initial conditions of a port are: * No device connected * Port disabled. When a device is attached, the port state transitions to the attached state and system software will process this as with any status change notification. Refer to Section 4 of the xHCI Specification for operational requirements for how change events interact with port suspend mode. Bit Description 31 Warm Port Reset (WPR)--R/WO. When software sets this bit to 1b, the Warm Reset sequence is initiated and the PR bit is set to 1b. Once initiated, the PR, PRC, and WRC bits shall reflect the progress of the Warm Reset sequence. This flag shall always return 0b when read. 30 Note: This bit applies only to USB 3.0 capable ports. For ports that are only USB 2.0 capable, this bit is Reserved. Note: This bit is in the Suspend Well. Device Removable (DR)--RO. This bit indicates if this port has a removable device attached. 0 = Device is removable. 1 = Device is non-removable. Note: 29:28 27 Wake on Over-current Enable (WOE)--R/W. 0 = Disable. (Default) 1 = Enable. Writing this bit to a 1b enables the port to be sensitive to over-current conditions as system wake-up events. Note: 26 This bit is in the Suspend Well. Wake on Connect Enable (WCE)--R/W. 0 = Disable. (Default) 1 = Enable. Writing this bit to a 1b enables the port to be sensitive to device connects as system wake-up events. Note: 606 This bit is in the Suspend Well. Wake on Disconnect Enable (WDE)--R/W. 0 = Disable. (Default) 1 = Enable. Writing this bit to a 1b enables the port to be sensitive to device disconnects as system wake-up events. Note: 25 This bit is in the Core Well. Reserved. This bit is in the Suspend Well. Datasheet xHCI Controller Registers (D20:F0) Bit 24 23 22 Description Cold Attach Status (CAS)--RO. This bit indicates that far-end terminations were detected in the Disconnected state and the Root Hub Port State Machine was unable to advance to the Enabled state. Software shall clear this bit by writing a 1b to the WPR bit or the xHC shall clear this bit if the CSS bit transitions to 1. Note: This bit is 0b if the PP bit is 0b or for USB 2.0 capable-only ports. Note: This bit is in the Suspend Well. Port Config Error Change (CEC)--R/W. This flag indicates that the port failed to configure its link partner. Software shall clear this bit by writing a 1 to it. Note: This bit applies only to USB 3.0 capable ports. This bit is Reserved for USB 2.0 capable-only ports. Note: This bit is in the Suspend Well. Port Link State Change (PLC)--R/WC. 0 = No change 1 = Link Status Change This flag is set to `1' due to the following Port Link State (PLS) transitions: Transition Condition U3 -> Resume Wakeup signaling from a device Resume -> Recovery -> U0 Device Resume complete (USB 3.0 capable ports only) Resume -> U0 Device Resume complete (USB 2.0 capable-only ports) U3 -> Recovery -> U0 Software Resume complete (USB 3.0 capable ports only) U3 -> U0 Software Resume complete (USB 2.0 capable-only ports) U2 -> U0 L1 Resume complete (USB 2.0 capable-only ports) U0 -> U0 L1 Entry Reject (USB 2.0 capable-only ports) U0 -> Disabled L1 Entry Error (USB 2.0 capable-only ports) Any state -> Inactive Error (USB 3.0 capable ports only) Notes: 1. This bit shall not be set if the PLS transition was due to software setting the PP bit to 0b. 2. Software shall clear this bit by writing a 1 to it. 3. This bit is in the Suspend Well. 21 Port Reset Change (PRC)--R/WC. This flag is set to `1' due a '1' to '0' transition of Port Reset (PR); such as when any reset processing on this port is complete. 0 = No change 1 = Reset Complete Notes: 1. This bit shall not be set to 1b if the reset processing was forced to terminate due to software clearing the PP bit or PED bit to 0b. 2. Software shall clear this bit by writing a 1 to it. 3. This bit is in the Suspend Well. 20 Over-current Change (OCC)--R/WC. The functionality of this bit is not dependent upon the port owner. Software clears this bit by writing a 1 to it. 0 = No change. (Default) 1 = There is a change to Overcurrent Active. Note: 19 Datasheet This bit is in the Suspend Well. Warm Port Reset Change (WRC)--R/WC. This bit is set when Warm Reset processing on this port completes. 0 = No change. (Default) 1 = Warm reset complete Notes: 1. This bit shall not be set to 1b if the reset processing was forced to terminate due to software clearing the PP bit or PED bit to 0b. 2. Software shall clear this bit by writing a 1 to it. 3. This bit applies only to USB 3.0 capable ports. This bit is Reserved for USB 2.0 capable-only ports. 4. This bit is in the Suspend Well. 607 xHCI Controller Registers (D20:F0) Bit Description 18 Port Enabled/Disabled Change (PEC)--R/WC. 0 = No change. (Default) 1 = There is a change to PED bit. Notes: 1. This bit shall not be set if the PED transition was due to software setting the PP bit to 0. 2. Software shall clear this bit by writing a 1 to it. 3. For a USB 2.0-only port, this bit shall be set to 1 only when the port is disabled due to the appropriate conditions existing at the EOF2 point. (See Chapter 11 of the USB Specification for the definition of a port error). 4. For a USB 3.0 port, this bit shall be set to `1' if an enabled port transitions to a Disabled state (that is, a `1' to `0' transition of PED). Refer to Section 4 of the xHCI Specification for more information. 5. This bit is in the Suspend Well. 17 Connect Status Change (CSC)--R/WC. This flag indicates a change has occurred in the port's Current Connect Status (CCS) or Cold Attach Status (CAS) bits. 0 = No change. (Default) 1 = There is a change to the CCS or CAS bit. The xHC sets this bit to 1b for all changes to the port device connect status, even if system software has not cleared an existing Connect Status Change. For example, the insertion status changes twice before system software has cleared the changed condition, root hub hardware will be "setting" an already-set bit (that is, the bit will remain 1b). Notes: 1. This bit shall not be set if the CCS transition was due to software setting the PP bit to 0b, or the CAS bit transition was die to software setting the WPR bit to 1b. 2. Software shall clear this bit by writing a 1 to it. 3. This bit is in the Suspend Well. 16 Port Link State Write Strobe (LWS)--R/W. 0 = When 0b, write data in PLS field is ignored. (Default) 1 = When this bit is set to 1b on a write reference to this register, this flag enables writes to the PLS field. Reads to this bit return `0'. Note: This bit is in the Suspend Well. 15:14 Reserved. 13:10 Port Speed (Port_Speed). A device attached to this port operates at a speed defined by the following codes: Value Speed 0001b Full-speed (12 Mb/s) 0010b Low-speed (1.5 Mb/s) 0011b High-speed (480 Mb/s) All other values reserved. Refer to the eXtensible Host Controller Interface for Universal Serial Bus Specification for additional details. Note: 9 Note: 608 This bit is in the Suspend Well. Port Power (PP)--RO. Read-only with a value of 1. This indicates that the port does have power. This bit is in the Suspend Well. Datasheet xHCI Controller Registers (D20:F0) Bit Description 8:5 Port Link State (PLS)--R/W. This field is used to power manage the port and reflects its current link state. When the port is in the Enabled state, system software may set the link U-state by writing this field. System software may also write this field to force a Disabled to Disconnected state transition of the port. Write Value Description 0 The link shall transition to a U0 state from any of the U-states. 2 USB 2.0 ports only. The link should transition to the U2 State. 3 The link shall transition to a U3 state from any of the U-states. This action selectively suspends the device connected to this port. While the Port Link State = U3, the hub does not propagate downstream-directed traffic to this port, but the hub will respond to resume signaling from the port. 5 USB 3.0 ports only. If the port is in the Disabled state (PLS = Disabled, PP = 1), then the link shall transition to a RxDetect state and the port shall transition to the Disconnected state, else ignored. 15 USB 2.0 ports only. If the port is in the U3 state (PLS = U3), then the link shall remain in the U3 state and the port shall transition to the U3Exit substate, else ignored. All other values Note: Ignored The Port Link State Write Strobe (LWS) shall be set to 1b to write this field. Read Value Definition 0 Link is in the U0 State 1 Link is in the U1 State 2 Link is in the U2 State 3 Link is in the U3 State (Device Suspended) 4 Link is in the Disabled State 5 Link is in the RxDetect State 6 Link is in the Inactive State 7 Link is in the Polling State 8 Link is in the Recovery State 9 Link is in the Hot Reset State 10 11 12-14 15 Link is in the Compliance Mode State Link is in the Test Mode State Reserved Link is in the Resume State Notes: 1. This field is undefined if PP = 0. 2. Transitions between different states are not reflected until the transition is complete. 3. This bit is in the Suspend Well. 4 Port Reset (PR)--R/W. When software writes a 1 to this bit (from a 0), the bus reset sequence as defined in the USB Specification, Revision 2.0 is started. Software writes a 0 to this bit to terminate the bus reset sequence. Software must keep this bit at a 1 long enough to ensure the reset sequence completes as specified in the USB Specification, Revision 2.0. USB 3.0 ports shall execute the Hot Reset sequence as defined in the USB 3.0 Specification. PR remains set until reset signaling is completed by the root hub. 1 = Port is in Reset. 0 = Port is not in Reset. 3 Overcurrent Active (OCA)--RO. 0 = This port does not have an overcurrent condition. (Default) 1 = This port currently has an overcurrent condition. This bit will automatically transition from 1 to 0 when the over current condition is removed. The PCH automatically disables the port when the overcurrent active bit is 1. Note: Note: 2 Datasheet This bit is in the Suspend Well. This bit is in the Suspend Well. Reserved. 609 xHCI Controller Registers (D20:F0) Bit Description 1 Port Enabled/Disabled--R/W. Ports can only be enabled by the host controller as a part of the reset and enable. Software cannot enable a port by writing a 1 to this bit. Ports can be disabled by either a fault condition (disconnect event or other fault condition) or by host software. The bit status does not change until the port state actually changes. There may be a delay in disabling or enabling a port due to other host controller and bus events. 0 = Disable 1 = Enable (Default) 0 Current Connect Status--RO. This value reflects the current state of the port, and may not correspond directly to the event that caused the Connect Status Change bit (Bit 1) to be set. 0 = No device is present. (Default) 1 = Device is present on port. Note: Note: 16.2.2.11 This bit is in the Suspend Well. This bit is in the Suspend Well. PORTPMSCNUSB2--xHCI Port N Power Management Status and Control USB2 Register Offset: There are 15 USB2 PORTPMSC registers at offsets: 484h, 494h, 4A4h, 4B4h, 4C4h, 4D4h, 4E4h, 4F4h, 504h, 514h, 524h, 534h, 544h, 554h, 564h Attribute: R/W, RO Default Value: 00000000h Size: 32 bits Bit Description 31:28 Port Test Control--R/W. When this field is `0', the port is not operating in a test mode. (Default) A non-zero value indicates that the port is operating in test mode and the specific test mode is indicated by the specific value. A non-zero Port Test Control value is only valid to a port that is in the Disabled state. If the port is not in this state, the xHC shall respond with the Port Test Control field set to Port Test Control Error. The encoding of the Test Mode bits for a USB 2.0 port are: Value Test Mode 0h Test mode not enabled 1h Test J_STATE 2h Test K_STATE 3h Test SE0_NAK 4h Test Packet 5h Test FORCE_ENABLE 6h-14h 15 Reserved. Port Test Control Error Refer to the Sections 7.1.20 and 11.24.2.13 of the USB 2.0 Specification for more information on Test Modes. Note: 27:17 16 Hardware LPM Enable (HLE)--RO. 0 = Disable. 1 = Enable. When this bit is a 1, hardware controlled LPM shall be enabled for this port. Refer to Section 4 of the USB 2.0 LPM Specification for more information. Note: 15:8 This bit is in the Suspend Well. L1 Device Slot--R/W. System software sets this field to indicate the ID of the Device Slot associated with the device directly attached to the Root Hub port. A value of 0 indicates there is no device present. Note: 610 This bit is in the Suspend Well. Reserved. This bit is in the Suspend Well. Datasheet xHCI Controller Registers (D20:F0) Bit Description 7:4 Host Initiated Resume Duration (HIRD)--R/W. System software sets this field to indicate to the recipient device how long the xHC will drive resume if it (the xHC) initiates an exit from L1. The HIRD value is encoded as follows: The value of 0000b is interpreted as 50 s. Each incrementing value up adds 75 s to the previous value. For example, 0001b is 125 s, 0010b is 200 s and so on. Based on this rule, the maximum value resume drive time is at encoding value 1111b which represents 1.2ms. Refer to Section 4 of the USB 2.0 LPM Specification for more information. Note: 3 Remote Wake Enable (RWE)--R/W. The host system sets this flag to enable or disable the device for remote wake from L1. 0 = Disable. (Default) 1 = Enable. The value of this flag will temporarily (while in L1) override the current setting of the Remote Wake feature set by the standard Set/ClearFeature() commands defined in Universal Serial Bus Specification, revision 2.0, Chapter 9. Note: 2:0 This bit is in the Suspend Well. L1 status--RO. Note: 16.2.2.12 This bit is in the Suspend Well. This bit is in the Suspend Well. PORTSCNUSB3--xHCI USB 3.0 Port N Status and Control Register Offset: There are 6 USB3 PORTSC registers at offsets: 570h, 580h, 590h, 5A0h, 5B0h, 5C0h Attribute: R/W,RO Default Value: 000002A0h Size: 32 bits A host controller must implement one or more port registers. Software uses the N_Port information from the Structural Parameters Register to determine how many ports need to be serviced. All ports have the structure defined below. Software must not write to unreported Port Status and Control Registers. This register is in the suspend power well. It is only reset by hardware when the suspend power is initially applied or in response to a host controller reset. The initial conditions of a port are: * No device connected * Port disabled. When a device is attached, the port state transitions to the attached state and system software will process this as with any status change notification. Refer to Section 4 of the xHCI Specification for operational requirements for how change events interact with port suspend mode. Bit Description 31 Warm Port Reset (WPR)--R/WO. When software sets this bit to 1b, the Warm Reset sequence is initiated and the PR bit is set to 1b. Once initiated, the PR, PRC, and WRC bits shall reflect the progress of the Warm Reset sequence. This flag shall always return 0b when read. Note: This bit applies only to USB 3.0 capable ports. For ports that are only USB 2.0 capable, this bit is Reserved. Note: 30 Note: 29:28 Datasheet This bit is in the Suspend Well. Device Removable (DR)--RO. This bit indicates if this port has a removable device attached. 0 = Device is removable. 1 = Device is non-removable. This bit is in the Core Well. Reserved. 611 xHCI Controller Registers (D20:F0) Bit 27 Description Wake on Over-current Enable (WOE)--R/W. 0 = Disable. (Default) 1 = Enable. Writing this bit to a 1b enables the port to be sensitive to over-current conditions as system wake-up events. Note: 26 Note: 25 This bit is in the Suspend Well. Port Config Error Change (CEC)--R/W. This flag indicates that the port failed to configure its link partner. Software shall clear this bit by writing a 1 to it. Note: This bit applies only to USB 3.0 capable ports. This bit is Reserved for USB 2.0 capable-only ports. Note: 22 This bit is in the Suspend Well. Cold Attach Status (CAS)--RO. This bit indicates that far-end terminations were detected in the Disconnected state and the Root Hub Port State Machine was unable to advance to the Enabled state. Software shall clear this bit by writing a 1b to the WPR bit or the xHC shall clear this bit if the CSS bit transitions to 1. Note: This bit is 0b if the PP bit is 0b or for USB 2.0 capable-only ports. Note: 23 This bit is in the Suspend Well. Wake on Connect Enable (WCE)--R/W. 0 = Disable. (Default) 1 = Enable. Writing this bit to a 1b enables the port to be sensitive to device connects as system wake-up events. Note: 24 This bit is in the Suspend Well. Wake on Disconnect Enable (WDE)--R/W. 0 = Disable. (Default) 1 = Enable. Writing this bit to a 1b enables the port to be sensitive to device disconnects as system wake-up events. This bit is in the Suspend Well. Port Link State Change (PLC)--R/WC. 0 = No change 1 = Link Status Change This flag is set to `1' due to the following Port Link State (PLS) transitions: Transition Condition U3 -> Resume Wakeup signaling from a device Resume -> Recovery -> U0 Device Resume complete (USB 3.0 capable ports only) Resume -> U0 Device Resume complete (USB 2.0 capable-only ports) U3 -> Recovery -> U0 Software Resume complete (USB 3.0 capable ports only) U3 -> U0 Software Resume complete (USB 2.0 capable-only ports) U2 -> U0 L1 Resume complete (USB 2.0 capable-only ports) U0 -> U0 L1 Entry Reject (USB 2.0 capable-only ports) U0 -> Disabled L1 Entry Error (USB 2.0 capable-only ports) Any state -> Inactive Error (USB 3.0 capable ports only) Notes: 1. This bit shall not be set if the PLS transition was due to software setting the PP bit to 0b. 2. Software shall clear this bit by writing a 1 to it. 3. This bit is in the Suspend Well. 21 612 Port Reset Change (PRC)--R/WC. This flag is set to `1' due a '1' to '0' transition of Port Reset (PR); such as when any reset processing on this port is complete. 0 = No change 1 = Reset Complete Notes: 1. This bit shall not be set to 1b if the reset processing was forced to terminate due to software clearing the PP bit or PED bit to 0b. 2. Software shall clear this bit by writing a 1 to it. 3. This bit is in the Suspend Well. Datasheet xHCI Controller Registers (D20:F0) Bit 20 Description Over-current Change (OCC)--R/WC. The functionality of this bit is not dependent upon the port owner. Software clears this bit by writing a 1 to it. 0 = No change. (Default) 1 = There is a change to Overcurrent Active. Note: This bit is in the Suspend Well. 19 Warm Port Reset Change (WRC)--R/WC. This bit is set when Warm Reset processing on this port completes. 0 = No change. (Default) 1 = Warm reset complete Notes: 1. This bit shall not be set to 1b if the reset processing was forced to terminate due to software clearing the PP bit or PED bit to 0b. 2. Software shall clear this bit by writing a 1 to it. 3. This bit applies only to USB 3.0 capable ports. This bit is Reserved for USB 2.0 capable-only ports. 4. This bit is in the Suspend Well. 18 Port Enabled/Disabled Change (PEC)--R/WC. 0 = No change. (Default) 1 = There is a change to PED bit. Notes: 1. This bit shall not be set if the PED transition was due to software setting the PP bit to 0. 2. Software shall clear this bit by writing a 1 to it. 3. For a USB 2.0-only port, this bit shall be set to 1 only when the port is disabled due to the appropriate conditions existing at the EOF2 point. (See Chapter 11 of the USB Specification for the definition of a port error). 4. For a USB 3.0 port, this bit shall be set to `1' if an enabled port transitions to a Disabled state (that is, a `1' to `0' transition of PED). Refer to Section 4 of the xHCI Specification for more information. 5. This bit is in the Suspend Well. 17 Connect Status Change (CSC)--R/WC. This flag indicates a change has occurred in the port's Current Connect Status (CCS) or Cold Attach Status (CAS) bits. 0 = No change. (Default) 1 = There is a change to the CCS or CAS bit. The xHC sets this bit to 1b for all changes to the port device connect status, even if system software has not cleared an existing Connect Status Change. For example, the insertion status changes twice before system software has cleared the changed condition, root hub hardware will be "setting" an already-set bit (that is, the bit will remain 1b). Notes: 1. This bit shall not be set if the CCS transition was due to software setting the PP bit to 0b, or the CAS bit transition was die to software setting the WPR bit to 1b. 2. Software shall clear this bit by writing a 1 to it. 3. This bit is in the Suspend Well. 16 Port Link State Write Strobe (LWS)--R/W. 0 = When 0b, write data in PLS field is ignored. (Default) 1 = When this bit is set to 1b on a write reference to this register, this flag enables writes to the PLS field. Reads to this bit return `0'. Note: This bit is in the Suspend Well. 15:14 Reserved. 13:10 Port Speed (Port_Speed). A device attached to this port operates at a speed defined by the following codes: Value Speed 0100 SuperSpeed (5 Gb/s) All other values reserved. Refer to the eXtensible Host Controller Interface for Universal Serial Bus Specification for additional details. 9 Port Power (PP)--RO. Read-only with a value of 1. This indicates that the port does have power. Note: Datasheet This bit is in the Suspend Well. 613 xHCI Controller Registers (D20:F0) Bit Description 8:5 Port Link State (PLS)--R/W. This field is used to power manage the port and reflects its current link state. When the port is in the Enabled state, system software may set the link U-state by writing this field. System software may also write this field to force a Disabled to Disconnected state transition of the port. Write Value The link shall transition to a U0 state from any of the U-states. 2 USB 2.0 ports only. The link should transition to the U2 State. 3 The link shall transition to a U3 state from any of the U-states. This action selectively suspends the device connected to this port. While the Port Link State = U3, the hub does not propagate downstream-directed traffic to this port, but the hub will respond to resume signaling from the port. 5 USB 3.0 ports only. If the port is in the Disabled state (PLS = Disabled, PP = 1), then the link shall transition to a RxDetect state and the port shall transition to the Disconnected state, else ignored. 15 All other values Note: Description 0 USB 2.0 ports only. If the port is in the U3 state (PLS = U3), then the link shall remain in the U3 state and the port shall transition to the U3Exit substate, else ignored. Ignored The Port Link State Write Strobe (LWS) shall be set to 1b to write this field. Read Value Definition 0 Link is in the U0 State 1 Link is in the U1 State 2 Link is in the U2 State 3 Link is in the U3 State (Device Suspended) 4 Link is in the Disabled State 5 Link is in the RxDetect State 6 Link is in the Inactive State 7 Link is in the Polling State 8 Link is in the Recovery State 9 Link is in the Hot Reset State 10 Link is in the Compliance Mode State 11 Link is in the Test Mode State 12-14 15 Reserved Link is in the Resume State Notes: 1. This field is undefined if PP = 0. 2. Transitions between different states are not reflected until the transition is complete. 3. This bit is in the Suspend Well. 4 Port Reset (PR)--R/W. When software writes a 1 to this bit (from a 0), the bus reset sequence as defined in the USB Specification, Revision 2.0 is started. Software writes a 0 to this bit to terminate the bus reset sequence. Software must keep this bit at a 1 long enough to ensure the reset sequence completes as specified in the USB Specification, Revision 2.0. USB 3.0 ports shall execute the Hot Reset sequence as defined in the USB 3.0 Specification. PR remains set until reset signaling is completed by the root hub. 1 = Port is in Reset. 0 = Port is not in Reset. 3 Overcurrent Active (OCA)--RO. 0 = This port does not have an overcurrent condition. (Default) 1 = This port currently has an overcurrent condition. This bit will automatically transition from 1 to 0 when the over current condition is removed. The PCH automatically disables the port when the overcurrent active bit is 1. Note: Note: 2 614 This bit is in the Suspend Well. This bit is in the Suspend Well. Reserved. Datasheet xHCI Controller Registers (D20:F0) Bit Description 1 Port Enabled/Disabled--R/W. Ports can only be enabled by the host controller as a part of the reset and enable. Software cannot enable a port by writing a 1 to this bit. Ports can be disabled by either a fault condition (disconnect event or other fault condition) or by host software. The bit status does not change until the port state actually changes. There may be a delay in disabling or enabling a port due to other host controller and bus events. 0 = Disable 1 = Enable (Default) 0 Current Connect Status--RO. This value reflects the current state of the port, and may not correspond directly to the event that caused the Connect Status Change bit (Bit 1) to be set. 0 = No device is present. (Default) 1 = Device is present on port. Note: Note: 16.2.2.13 This bit is in the Suspend Well. This bit is in the Suspend Well. PORTPMSCN--Port N Power Management Status and Control USB3 Register Offset: There are 6 USB3 PORTPMSCN registers at offsets: 574h, 584h, 594h, 5A4h, 5B4h, 5C4h Attribute: R/W, RO Default Value: 00000000h Size: 32 bits Bit 31:17 16 15:8 Description Reserved. Force Link PM Accept (FLA)--R/W. When this bit is set to `1', the port shall generate a Set Link Function LMP with the Force_LinkPM_Accept bit asserted. This bit shall be set to 0b by the assertion of PR to 1 or when CCS = transitions from 0 to 1. Writes to this flag have no affect if PP = 0b. The Set Link Function LMP is sent by the xHC to the device connected on this port when this bit transitions from 0' to 1. Refer to Sections 8.4.1, 10.4.2.2 and 10.4.2.9 of the USB 3.0 Specification for more details. U2 Timeout--R/W. Timeout value for U2 inactivity timer. If equal to FFh, the port is disabled from initiating U2 entry. This field shall be set to 0 by the assertion of PR to 1. Refer to Section 4 of the xHCI Specification for more information on U2 Timeout operation. The following are permissible values: Value Description 00h Zero (default) 01h 256 s 02h 512 s ... 7:0 FEh 65.024 ms FFh Infinite U1 Timeout--R/W. Timeout value for U1 inactivity timer. If equal to FFh, the port is disabled from initiating U1 entry. This field shall be set to 0 by the assertion of PR to 1. Refer to Section 4 of the xHCI Specification for more information on U1 Timeout operation. The following are permissible values: Value Description 00h Zero (default) 01h 1 s 02h 2 s ... 7Fh 80h-FEh FFh Datasheet 127 s Reserved Infinite 615 xHCI Controller Registers (D20:F0) 16.2.2.14 PORTLIX--USB 3.0 Port X Link Info Register Offset: There are 6 USB3 PORTLIX registers at offsets: 578h, 588h, 598h, 5A8h, 5B8h, 5C8h Attribute: RO Default Value: 00000000h Size: 32 bits Bit 31:16 15:0 16.2.3 Description Reserved. Link Error Count - RO. Host Controller Runtime Registers This section defines the xHC runtime registers. The base address of this register space is referred to as Runtime Base. The Runtime Base shall be 32-byte aligned and is calculated by adding the value Runtime Register Space Offset register (MEM_BASE+18h:bits 31:2) to the Capability Base address. All Runtime registers are multiples of 32 bits in length. Table 16-3. Enhanced Host Controller Operational Register Address Map Runtime Base + Offset 16.2.3.1 Power Well Mnemonic 00h-03h Core MFINDEX Microframe Index 00000000h RO 20h-23h Core IMAN Interrupter X Management 00000000h RO, R/W, R/WC 24h-27h Core IMOD Interrupter X Moderation 00000FA0h R/W 28h-2Bh Core ERSTSZ Event Ring Segment Table Size X 00000000h R/W, RO 30h-33h Core ERSTBAL Event Ring Segment Table Base Address Low X 00000000h R/W, RO 34h-37h Core ERSTBAH Event Ring Segment Table Base Address High X 00000000h R/W 38h-3Bh Core ERDPL Event Ring Dequeue Pointer Low X 00000000h R/W, R/WC 3Ch-3Fh Core ERDPH Event Ring Dequeue Pointer High X 00000000h R/W Default Type MFINDEX--Microframe Index Register Offset: Default Value: Bit 31:14 13:0 616 Register Name Runtime Base + 00h-03h 00000000h Attribute: Size: RO, 32 bits Description Reserved. Microframe Index--RO. The value in this register increments at the end of each microframe (such as 125 us.). Bits 13:3 may be used to determine the current 1ms. Frame Index. Datasheet xHCI Controller Registers (D20:F0) 16.2.3.2 IMAN--Interrupter X Management Register Offset: Attribute: Default Value: Note: Base Base Base Base Base Base Base Base + + + + + + + + 20h-23h 40h-43h 60h-63h 80h-83h A0h-A3h C0h-C3h E0h-E3h 100h-103h Size: 32 bits The xHC implements up to 8 Interrupters. There are 8 IMAN registers, one for each Interrupter. Bit 31:2 Datasheet Interrupter 1: Runtime Interrupter 2: Runtime Interrupter 3: Runtime Interrupter 4: Runtime Interrupter 5: Runtime Interrupter 6: Runtime Interrupter 7: Runtime Interrupter 8: Runtime RO, R/W, R/WC 00000000h Description Reserved. 1 Interrupt Enable (IE)--RO. This flag specifies whether the Interrupter is capable of generating an interrupt. 0 = The Interrupter is prohibited from generating interrupts. 1 = When this bit and the IP bit are set (1b), the Interrupter shall generate an interrupt when the Interrupter Moderation Counter reaches `0'. 0 Interrupt Pending (IP)--R/WC. 0 = No interrupt is pending for the Interrupter. 1 = An interrupt is pending for this Interrupter. This bit is set to 1b when IE = 1, the IMODI Interrupt Moderation Counter field = 0b, the Event Ring associated with the Interrupter is not empty (or for the Primary Interrupter when the HCE flag is set to 1b), and EHB = 0. If MSI interrupts are enabled, this flag shall be cleared automatically when the PCI DWord write generated by the Interrupt assertion is complete. If PCI Pin Interrupts are enabled, this flag shall be cleared by software. 617 xHCI Controller Registers (D20:F0) 16.2.3.3 IMOD--Interrupter X Moderation Register Offset: Attribute: Default Value: Note: 16.2.3.4 Base Base Base Base Base Base Base Base + + + + + + + + 24h-27h 44h-47h 64h-67h 84h-87h A4h-A7h C4h-C7h E4h-E7h 104h-107h Size: 32 bits Bit Description 31:16 Interrupt Moderation Counter (IMODC)--R/W. Down counter. Loaded with Interval Moderation value (value of bits 15:0) whenever the IP bit is cleared to 0b, counts down to `0', and stops. The associated interrupt shall be signaled whenever this counter is `0', the Event Ring is not empty, the IE and IP bits = 1, and EHB = 0. This counter may be directly written by software at any time to alter the interrupt rate. 15:0 Interrupt Moderation Interval (IMODI)--R/W. Minimum inter-interrupt interval. The interval is specified in 250ns increments. A value of `0' disables interrupt throttling logic and interrupts shall be generated immediately if IP = 0, EHB = 0, and the Event Ring is not empty. ERSTSZ--Event Ring Segment Table Size X Register Attribute: Default Value: 1: Runtime 2: Runtime 3: Runtime 4: Runtime 5: Runtime 6: Runtime 7: Runtime 8: Runtime R/W, RO 00000000h Base Base Base Base Base Base Base Base + + + + + + + + 28h-2Bh 48h-4Bh 68h-6Bh 88h-8Bh A8h-ABh C8h-CBh E8h-EBh 108h-10Bh Size: 32 bits There are 8 ERSTSZ registers. Bit 31:16 15:0 618 Runtime Runtime Runtime Runtime Runtime Runtime Runtime Runtime The xHC implements up to 8 Interrupters. There are 8 IMOD registers, one for each Interrupter. Offset: Note: Interrupter 1: Interrupter 2: Interrupter 3: Interrupter 4: Interrupter 5: Interrupter 6: Interrupter 7: Interrupter 8: R/W 00000FA0h Description Reserved. Event Ring Segment Table Size--R/W. This field identifies the number of valid Event Ring Segment Table entries in the Event Ring Segment Table pointed to by the Event Ring Segment Table Base Address register. Datasheet xHCI Controller Registers (D20:F0) 16.2.3.5 ERSTBAL--Event Ring Segment Table Base Address Low X Register Offset: Attribute: Default Value: Note: 30h-33h 50h-53h 70h-73h 90h-93h B0h-B3h D0h-D3h F0h-F3h 110h-113h Size: 32 bits Description 31:6 Event Ring Segment Table Base Address Register (ERSTBA_LO)--R/W. This field defines the low order bits of the start address of the Event Ring Segment Table. This field shall not be modified if HCHalted (HCH) = 0. Reserved. ERSTBAH--Event Ring Segment Table Base Address High X Register Attribute: Default Value: Datasheet + + + + + + + + Bit Offset: Note: Base Base Base Base Base Base Base Base There are 8 ERSTBAL registers. 5:0 16.2.3.6 1: Runtime 2: Runtime 3: Runtime 4: Runtime 5: Runtime 6: Runtime 7: Runtime 8: Runtime R/W, RO 00000000h 1: Runtime Base + 34h-37h 2: Runtime Base + 54h-57h 3: Runtime Base + 74h-77h 4: Runtime Base + 94h-97h 5: Runtime Base + B4h-B7h 6: Runtime Base + D4h-D7h 7: Runtime Base + F4h-F7h 8: 1Runtime Base + 14h-117h R/W 00000000h Size: 32 bits There are 8 ERSTBAH registers. Bit Description 31:0 Event Ring Segment Table Base Address Register (ERSTBA_HI)--R/W. This field defines the low order bits of the start address of the Event Ring Segment Table. This field shall not be modified if HCHalted (HCH) = 0. 619 xHCI Controller Registers (D20:F0) 16.2.3.7 ERDPL--Event Ring Dequeue Pointer Low X Register Offset: Attribute: Default Value: Note: 38h-3Bh 58h-5Bh 78h-7Bh 98h-9Bh B8h-BBh D8h-dBh F8h-FBh 118h-11Bh Size: 32 bits Description 31:4 Event Ring Dequeue Pointer--R/W. This field defines the low order bits of the 64- bit address of the current Event Ring Dequeue Pointer. Event Handler Busy (EHB)--R/WC. This flag shall be set to `1' when the IP bit is set to `1' and cleared to `0' by software when the Dequeue Pointer register is written. Dequeue ERST Segment Index (DESI)--R/W. This field may be used by the xHC to accelerate checking the Event Ring full condition. This field is written with the low order 3 bits of the offset of the ERST entry which defines the Event Ring segment that Event Ring Dequeue Pointer resides in. ERDPH--Event Ring Dequeue Pointer High X Register Offset: Attribute: Default Value: 16.2.4 + + + + + + + + Bit 2:0 Note: Base Base Base Base Base Base Base Base There are 8 ERDPL registers. 3 16.2.3.8 1: Runtime 2: Runtime 3: Runtime 4: Runtime 5: Runtime 6: Runtime 7: Runtime 8: Runtime R/W, R/WC 00000000h 1: Runtime 2: Runtime 3: Runtime 4: Runtime 5: Runtime 6: Runtime 7: Runtime 8: Runtime R/W 00000000h Base Base Base Base Base Base Base Base + + + + + + + + 3Ch-3Fh 5Ch-5Fh 7Ch-7Fh 9Ch-9Fh BCh-BFh DCh-DFh FCh-FFh 11Ch-11Fh Size: 32 bits There are 8 ERDPH registers. Bit Description 31:0 Event Ring Dequeue Pointer--R/W. This field defines the low order bits of the 64- bit address of the current Event Ring Dequeue Pointer. Doorbell Registers Door Bell registers are an array of 64 registers, with 0 to 32 being used by the xHC and the remainder being reserved. One 32-bit Doorbell Register is defined in the array for each Device Slot. System software utilizes the Doorbell Register to notify the xHC that it has Device Slot related work for the xHC to perform. These registers are pointed to by the Doorbell Offset Register (dBOFF) in the xHC Capability register space. The Doorbell Array base address shall be DWord aligned and is calculated by adding the value in the dBOFF register (MEM_BASE+14h-17h) to "Base" (the base address of the xHCI Capability register address space). 620 Datasheet xHCI Controller Registers (D20:F0) All registers are 32 bits in length. Software should read and write these registers using only DWord accesses. 16.2.4.1 DOORBELL--Doorbell X Register Offset: Attribute: Default Value: Power Well Doorbell 1: dBOFF + 00h-03h Doorbell 2: dBOFF + 04h-07h .... Doorbell 32: dBOFF + 7Ch-7Fh R/W 00000000h Core Note: There are 32 contiguous DOORBELL registers. Note: Reading this register will always show 00000000h. Bit 31:16 15:8 7:0 Size: 32 bits Description dB Stream ID--R/W. If the endpoint of a Device Context Doorbell defines Streams, then this field shall be used to identify which Stream of the endpoint the doorbell reference is targeting. System software is responsible for ensuring that the value written to this field is valid. If the endpoint does not define Streams (MaxPStreams = 0) and a non-'0' value is written to this field, the doorbell reference shall be ignored. This field only applies to Device Context Doorbells and shall be cleared to `0' for Host Controller Commands. This field returns `0' when read. Reserved. dB Target--R/W. This field defines the target of the doorbell reference. Refer to the xHCI Specification for definitions of the values. Note that Doorbell Register 0 is dedicated to Command Ring and decodes this field differently than the other Doorbell Registers. This field returns `0' when read and should be treated as "undefined" by software. When the Host Controller Doorbell (0) is written, the DB TaskStream ID field shall be set to `0'. Datasheet 621 Integrated Intel(R) High Definition Audio (Intel(R) HD Audio) Controller Registers 17 Integrated Intel(R) High Definition Audio (Intel(R) HD Audio) Controller Registers 17.1 Intel(R) High Definition Audio (Intel(R) HD Audio) Controller Registers (D27:F0) The Intel High Definition Audio controller resides in PCI Device 27, Function 0 on bus 0. This function contains a set of DMA engines that are used to move samples of digitally encoded data between system memory and external codecs. Note: All registers in this function (including memory-mapped registers) are addressable in byte, word, and DWord quantities. The software must always make register accesses on natural boundaries (that is, DWord accesses must be on DWord boundaries; word accesses on word boundaries, and so on). Register access crossing the DWord boundary are ignored. In addition, the memory-mapped register space must not be accessed with the LOCK semantic exclusive-access mechanism. If software attempts exclusive-access mechanisms to the Intel High Definition Audio memory-mapped space, the results are undefined. Note: Users interested in providing feedBack on the Intel High Definition Audio specification or planning to implement the Intel High Definition Audio specification into a future product will need to execute the Intel(R) High Definition Audio Specification Developer's Agreement. For more information, contact nextgenaudio@intel.com. 17.1.1 Intel(R) High Definition Audio PCI Configuration Space (Intel(R) High Definition Audio--D27:F0) Note: Address locations that are not shown should be treated as Reserved. Table 17-1. Intel(R) High Definition Audio (Intel(R) HD Audio) PCI Register Address Map (Intel(R) High Definition Audio D27:F0) (Sheet 1 of 3) Offset 622 Mnemonic Register Name Default Attribute 00h-01h VID Vendor Identification 8086h RO 02h-03h DID Device Identification See register description RO 04h-05h PCICMD PCI Command 0000h R/W, RO 06h-07h PCISTS PCI Status 0010h R/WC, RO 08h RID Revision Identification See register description RO 09h PI Programming Interface 00h RO 0Ah SCC Sub Class Code 03h RO 0Bh BCC Base Class Code 04h RO 0Ch CLS 0Dh LT 0Eh HEADTYP Cache Line Size 00h R/W Latency Timer 00h RO Header Type 00h RO Datasheet Integrated Intel(R) High Definition Audio (Intel(R) HD Audio) Controller Registers Table 17-1. Intel(R) High Definition Audio (Intel(R) HD Audio) PCI Register Address Map (Intel(R) High Definition Audio D27:F0) (Sheet 2 of 3) Datasheet Offset Mnemonic 10h-13h HdBARL 14h-17h HdBARU 2Ch-2Dh SVID 2Eh-2Fh SID 34h CAPPTR Register Name Default Attribute Intel(R) High Definition Audio Lower Base Address (Memory) 00000004h R/W, RO Intel(R) High Definition Audio Upper Base Address (Memory) 00000000h R/W Subsystem Vendor Identification 0000h R/WO Subsystem Identification 0000h R/WO 50h RO Capability List Pointer 3Ch INTLN Interrupt Line 00h R/W 3Dh INTPN Interrupt Pin See Register Description RO 40h HDCTL Intel(R) High Definition Audio Control 01h R/W, RO 4Ch DCKCTL Docking Control (Mobile Only) 00h R/W, RO 4Dh DCKSTS Docking Status (Mobile Only) 80h R/WO, RO 50h-51h PID PCI Power Management Capability ID 6001h R/WO, RO 52h-53h PC Power Management Capabilities 54h-57h PCS Power Management Control and Status 60h-61h MID MSI Capability ID 7005h RO 62h-63h MMC MSI Message Control 0080h R/W, RO C842h RO 00000000h R/W, RO, R/WC 64h-67h MMLA MSI Message Lower Address 00000000h R/W, RO 68h-6Bh MMUA MSI Message Upper Address 00000000h R/W 6Ch-6Dh MMD MSI Message Data 0000h R/W 70h-71h PXID PCI Express* Capability Identifiers 0010h RO 72h-73h PXC 74h-77h DEVCAP 78h-79h DEVC 7Ah-7Bh DEVS PCI Express Capabilities 0091h RO 10000000h RO, R/WO Device Control 0800h R/W, RO Device Status 0010h RO Device Capabilities 100h-103h VCCAP Virtual Channel Enhanced Capability Header 13010002h R/WO 104h-107h PVCCAP1 Port VC Capability Register 1 00000001h RO 108h-10Bh PVCCAP2 Port VC Capability Register 2 00000000h RO 10Ch-10D PVCCTL Port VC Control 0000h RO 10Eh-10Fh PVCSTS Port VC Status 0000h RO 110h-113h VC0CAP VC0 Resource Capability 00000000h RO 114h-117h VC0CTL VC0 Resource Control 800000FFh R/W, RO 11Ah-11Bh VC0STS VC0 Resource Status 0000h RO 11Ch-11Fh VCiCAP VCi Resource Capability 00000000h RO 120h-123h VCiCTL VCi Resource Control 00000000h R/W, RO 126h-127h VCiSTS VCi Resource Status 130h-133h RCCAP Root Complex Link Declaration Enhanced Capability Header 134h-137h ESD 140h-143h L1DESC 0000h RO 00010005h RO Element Self Description 0F000100h RO Link 1 Description 00000001h RO 623 Integrated Intel(R) High Definition Audio (Intel(R) HD Audio) Controller Registers Table 17-1. Intel(R) High Definition Audio (Intel(R) HD Audio) PCI Register Address Map (Intel(R) High Definition Audio D27:F0) (Sheet 3 of 3) 17.1.1.1 Offset Mnemonic 148h-14Bh L1ADDL 14Ch-14Fh L1ADDU Register Name Default Attribute Link 1 Lower Address See Register Description RO Link 1 Upper Address 00000000h RO VID--Vendor Identification Register (Intel(R) High Definition Audio Controller--D27:F0) Offset: Default Value: 00h-01h 8086h Bit 15:0 17.1.1.2 Attribute: Size: Description Vendor ID--RO. This is a 16-bit value assigned to Intel. Intel VID = 8086h DID--Device Identification Register (Intel(R) High Definition Audio Controller--D27:F0) Offset Address: 02h-03h Default Value: See bit description Bit 15:0 17.1.1.3 Attribute: Size: RO 16 bits Description Device ID--RO. This is a 16-bit value assigned to the PCH's Intel(R) High Definition Audio controller. See Section 1.3 for the value of the DID Register. PCICMD--PCI Command Register (Intel(R) High Definition Audio Controller--D27:F0) Offset Address: 04h-05h Default Value: 0000h Bit 15:11 10 Attribute: Size: R/W, RO 16 bits Description Reserved Interrupt Disable (ID)--R/W. 0= The INTx# signals may be asserted. 1= The Intel High Definition Audio controller's INTx# signal will be de-asserted. Note: 624 RO 16 bits This bit does not affect the generation of MSIs. 9 Fast Back to Back Enable (FBE)--RO. Hardwired to 0. 8 SERR# Enable (SERR_EN)--R/W. SERR# is not generated by the PCH Intel High Definition Audio Controller. 7 Wait Cycle Control (WCC)--RO. Hardwired to 0. 6 Parity Error Response (PER)--R/W. PER functionality not implemented. 5 VGA Palette Snoop (VPS)--RO. Hardwired to 0. 4 Memory Write and Invalidate Enable (MWIE)--RO. Hardwired to 0. 3 Special Cycle Enable (SCE)--RO. Hardwired to 0. 2 Bus Master Enable (BME)--R/W. Controls standard PCI Express* bus mastering capabilities for Memory and I/O, reads and writes. This bit also controls MSI generation since MSI's are essentially Memory writes. 0 = Disable 1 = Enable Datasheet Integrated Intel(R) High Definition Audio (Intel(R) HD Audio) Controller Registers Bit 17.1.1.4 Description 1 Memory Space Enable (MSE)--R/W. Enables memory space addresses to the Intel High Definition Audio controller. 0 = Disable 1 = Enable 0 I/O Space Enable (IOSE)--RO. Hardwired to 0 since the Intel High Definition Audio controller does not implement I/O space. PCISTS--PCI Status Register (Intel(R) High Definition Audio Controller--D27:F0) Offset Address: 06h-07h Default Value: 0010h Bit 15 Description Detected Parity Error (DPE)--RO. Hardwired to 0. 14 SERR# Status (SERRS)--RO. Hardwired to 0. Received Master Abort (RMA)--R/WC. Software clears this bit by writing a 1 to it. 0 = No master abort received. 1 = The Intel High Definition Audio controller sets this bit when, as a bus master, it receives a master abort. When set, the Intel High Definition Audio controller clears the run bit for the channel that received the abort. 12 Received Target Abort (RTA)--RO. Hardwired to 0. 11 Signaled Target Abort (STA)--RO. Hardwired to 0. DEVSEL# Timing Status (DEV_STS)--RO. Hardwired to 0. 8 Data Parity Error Detected (DPED)--RO. Hardwired to 0. 7 Fast Back to Back Capable (FB2BC)--RO. Hardwired to 0. 6 Reserved 5 66 MHz Capable (66MHZ_CAP)--RO. Hardwired to 0. 4 Capabilities List (CAP_LIST)--RO. Hardwired to 1. Indicates that the controller contains a capabilities pointer list. The first item is pointed to by looking at configuration offset 34h. 3 Interrupt Status (IS)--RO. 0 = This bit is 0 after the interrupt is cleared. 1 = This bit is 1 when the INTx# is asserted. This bit is not set by an MSI. 2:0 Reserved RID--Revision Identification Register (Intel(R) High Definition Audio Controller--D27:F0) Offset: Default Value: Datasheet RO, R/WC 16 bits 13 10:9 17.1.1.5 Attribute: Size: 08h See bit description Attribute: RO Size: 8 Bits Bit Description 7:0 Revision ID--RO. This field indicates the device specific revision identifier. See Section 1.3 for the value of the RID Register. 625 Integrated Intel(R) High Definition Audio (Intel(R) HD Audio) Controller Registers 17.1.1.6 PI--Programming Interface Register (Intel(R) High Definition Audio Controller--D27:F0) Offset: Default Value: 09h 00h Bit 7:0 17.1.1.7 Attribute: Size: Description Programming Interface--RO. SCC--Sub Class Code Register (Intel(R) High Definition Audio Controller--D27:F0) Address Offset: 0Ah Default Value: 03h Bit 7:0 17.1.1.8 Attribute: Size: Sub Class Code (SCC)--RO. 03h = Audio Device BCC--Base Class Code Register (Intel(R) High Definition Audio Controller--D27:F0) Bit 7:0 Attribute: Size: Base Class Code (BCC)--RO. 04h = multi-media device CLS--Cache Line Size Register (Intel(R) High Definition Audio Controller--D27:F0) Bit 7:0 Attribute: Size: R/W 8 bits Description Cache Line Size--R/W. Implemented as R/W register, but has no functional impact to the PCH LT--Latency Timer Register (Intel(R) High Definition Audio Controller--D27:F0) Address Offset: 0Dh Default Value: 00h Bit 7:0 626 RO 8 bits Description Address Offset: 0Ch Default Value: 00h 17.1.1.10 RO 8 bits Description Address Offset: 0Bh Default Value: 04h 17.1.1.9 RO 8 bits Attribute: Size: RO 8 bits Description Latency Timer--RO. Hardwired to 00 Datasheet Integrated Intel(R) High Definition Audio (Intel(R) HD Audio) Controller Registers 17.1.1.11 HEADTYP--Header Type Register (Intel(R) High Definition Audio Controller--D27:F0) Address Offset: 0Eh Default Value: 00h Bit 7:0 17.1.1.12 Attribute: Size: Description Header Type--RO. Hardwired to 00. HdBARL--Intel(R) High Definition Audio Lower Base Address Register (Intel(R) High Definition Audio--D27:F0) Address Offset: 10h-13h Default Value: 00000004h Bit 31:14 13:4 3 17.1.1.13 Attribute: Size: R/W, RO 32 bits Description Lower Base Address (LBA)--R/W. Base address for the Intel High Definition Audio controller's memory mapped configuration registers. 16 Kbytes are requested by hardwiring bits 13:4 to 0s. Reserved Prefetchable (PREF)--RO. Hardwired to 0 to indicate that this BAR is NOT prefetchable 2:1 Address Range (ADDRNG)--RO. Hardwired to 10b, indicating that this BAR can be located anywhere in 64-bit address space. 0 Space Type (SPTYP)--RO. Hardwired to 0. Indicates this BAR is located in memory space. HdBARU--Intel(R) High Definition Audio Upper Base Address Register (Intel(R) High Definition Audio Controller--D27:F0) Address Offset: 14h-17h Default Value: 00000000h 17.1.1.14 RO 8 bits Attribute: Size: R/W 32 bits Bit Description 31:0 Upper Base Address (UBA)--R/W. Upper 32 bits of the Base address for the Intel High Definition Audio controller's memory mapped configuration registers. SVID--Subsystem Vendor Identification Register (Intel(R) High Definition Audio Controller--D27:F0) Address Offset: 2Ch-2Dh Default Value: 0000h Function Level Reset: No Attribute: Size: R/WO 16 bits The SVID register, in combination with the Subsystem ID register (D27:F0:2Eh), enable the operating environment to distinguish one audio subsystem from the other(s). This register is implemented as write-once register. Once a value is written to it, the value can be read back. Any subsequent writes will have no effect. This register is not affected by the D3HOT to D0 transition. Bit 15:0 Datasheet Description Subsystem Vendor ID--R/WL. Locked when HDCTL.BCLD = 1. 627 Integrated Intel(R) High Definition Audio (Intel(R) HD Audio) Controller Registers 17.1.1.15 SID--Subsystem Identification Register (Intel(R) High Definition Audio Controller--D27:F0) Address Offset: 2Eh-2Fh Default Value: 0000h Function Level Reset:No Attribute: Size: R/WO 16 bits The SID register, in combination with the Subsystem Vendor ID register (D27:F0:2Ch) make it possible for the operating environment to distinguish one audio subsystem from the other(s). This register is implemented as write-once register. Once a value is written to it, the value can be read back. Any subsequent writes will have no effect. This register is not affected by the D3HOT to D0 transition. Bit 15:0 17.1.1.16 Description Subsystem ID--R/WL. Locked when HDCTL.BCLD = 1. CAPPTR--Capabilities Pointer Register (Intel(R) High Definition Audio Controller--D27:F0) Address Offset: 34h Default Value: 50h Attribute: Size: RO 8 bits This register indicates the offset for the capability pointer. 17.1.1.17 Bit Description 7:0 Capabilities Pointer (CAP_PTR)--RO. This field indicates that the first capability pointer offset is offset 50h (Power Management Capability). INTLN--Interrupt Line Register (Intel(R) High Definition Audio Controller--D27:F0) Address Offset: 3Ch Default Value: 00h Function Level Reset:No Bit 7:0 17.1.1.18 Attribute: Size: Description Interrupt Line (INT_LN)--R/W. This data is not used by the PCH. It is used to communicate to software the interrupt line that the interrupt pin is connected to. INTPN--Interrupt Pin Register (Intel(R) High Definition Audio Controller--D27:F0) Address Offset: 3Dh Default Value: See Description Bit 628 R/W 8 bits Attribute: Size: RO 8 bits Description 7:4 Reserved 3:0 Interrupt Pin (IP)--RO. This reflects the value of D27IP.ZIP (Chipset Config Registers:Offset 3110h:bits 3:0). Datasheet Integrated Intel(R) High Definition Audio (Intel(R) HD Audio) Controller Registers 17.1.1.19 HDCTL--Intel(R) High Definition Audio Control Register (Intel(R) High Definition Audio Controller--D27:F0) Address Offset: 40h Default Value: 01h Bit 7:2 17.1.1.20 Attribute: Size: Description Reserved 1 BIOS Configuration Lock Down Bit (BCLD): This bit being set is an indication that BIOS configuration is done and HD-Audio Controller hardware can start operates using the defined configurations. Setting this bit also lock down the read only field that BIOS initialized 0 Intel(R) High Definition Signal Mode--RO. This bit is hardwired to 1 (High Definition Audio mode). DCKCTL--Docking Control Register (Mobile Only) (Intel(R) High Definition Audio Controller--D27:F0) Address Offset: 4Ch Default Value: 00h Function Level Reset: No Bit 7:1 0 17.1.1.21 Attribute: Size: R/W, RO 8 bits Description Reserved Dock Attach (DA)--R/W / RO. Software writes a 1 to this bit to initiate the docking sequence on the HDA_DOCK_EN# and HDA_DOCK_RST# signals. When the docking sequence is complete, hardware will set the Dock Mated (GSTS.DM) status bit to 1. Software writes a 0 to this bit to initiate the undocking sequence on the HDA_DOCK_EN# and HDA_DOCK_RST# signals. When the undocking sequence is complete, hardware will set the Dock Mated (GSTS.DM) status bit to 0. Software must check the state of the Dock Mated (GSTS.DM) bit prior to writing to the Dock Attach bit. Software shall only change the DA bit from 0 to 1 when DM=0. Likewise, software shall only change the DA bit from 1 to 0 when DM=1. If these rules are violated, the results are undefined. This bit is Read Only when the DCKSTS.DS bit = 0. DCKSTS--Docking Status Register (Mobile Only) (Intel(R) High Definition Audio Controller--D27:F0) Address Offset: 4Dh Default Value: 80h Function Level Reset: No Attribute: Size: R/WO, RO 8 bits Bit Description 7 Docking Supported (DS)--R/WL. A 1 indicates that the PCH supports HD Audio Docking. The DCKCTL.DA bit is only writable when this DS bit is 1. ACPI BIOS software should only branch to the docking routine when this DS bit is 1. BIOS may clear this bit to 0 to prohibit the ACPI BIOS software from attempting to run the docking routines. This bit is reset to its default value only on a PLTRST#, but not on a CRST# or D3hot-to-D0 transition. Locked when HDCTL.BCLD = 1. 6:1 0 Datasheet RO 8 bits Reserved Dock Mated (DM)--RO. This bit effectively communicates to software that an Intel HD Audio docked codec is physically and electrically attached. Controller hardware sets this bit to 1 after the docking sequence triggered by writing a 1 to the Dock Attach (GCTL.DA) bit is completed (HDA_DOCK_RST# de-assertion). This bit indicates to software that the docked codec(s) may be discovered using the STATESTS register and then enumerated. Controller hardware sets this bit to 0 after the undocking sequence triggered by writing a 0 to the Dock Attach (GCTL.DA) bit is completed (HDA_DOCK_EN# de-asserted). This bit indicates to software that the docked codec(s) may be physically undocked. 629 Integrated Intel(R) High Definition Audio (Intel(R) HD Audio) Controller Registers 17.1.1.22 PID--PCI Power Management Capability ID Register (Intel(R) High Definition Audio Controller--D27:F0) Address Offset: 50h-51h Default Value: 6001h Function Level Reset: No (Bits 7:0 only) Bit 15:8 7:0 17.1.1.23 Attribute: Size: Description Next Capability (Next)--R/WL. Points to the next capability structure (MSI). Locked when HDCTL.BCLD = 1. Cap ID (CAP)--RO. Hardwired to 01h. Indicates that this pointer is a PCI power management capability. These bits are not reset by Function Level Reset. PC--Power Management Capabilities Register (Intel(R) High Definition Audio Controller--D27:F0) Address Offset: 52h-53h Default Value: C842h Attribute: Size: Description 15:11 PME Support--RO. Hardwired to 11001b. Indicates PME# can be generated from D3 and D0 states. 9 8:6 D2 Support--RO. Hardwired to 0. Indicates that D2 state is not supported. D1 Support--RO. Hardwired to 0. Indicates that D1 state is not supported. Aux Current--RO. Hardwired to 001b. Reports 55 mA maximum suspend well current required when in the D3COLD state. 5 Device Specific Initialization (DSI)--RO. Hardwired to 0. Indicates that no device specific initialization is required. 4 Reserved 3 2:0 PME Clock (PMEC)--RO. Does not apply. Hardwired to 0. Version--RO. Hardwired to 010b. Indicates support for version 1.1 of the PCI Power Management Specification. PCS--Power Management Control and Status Register (Intel(R) High Definition Audio Controller--D27:F0) Address Offset: 54h-57h Default Value: 00000000h Function Level Reset:No Bit 31:24 Attribute: Size: Data--RO. Does not apply. Hardwired to 0. Bus Power/Clock Control Enable--RO. Does not apply. Hardwired to 0. 22 B2/B3 Support--RO. Does not apply. Hardwired to 0. 15 14:9 RO, R/W, R/WC 32 bits Description 23 21:16 630 RO 16 bits Bit 10 17.1.1.24 R/WO, RO 16 bits Reserved PME Status (PMES)--R/WC. 0 = Software clears the bit by writing a 1 to it. 1 = This bit is set when the Intel High Definition Audio controller would normally assert the PME# signal independent of the state of the PME_EN bit (bit 8 in this register). This bit is in the resume well and is cleared by a power-on reset. Software must not make assumptions about the reset state of this bit and must set it appropriately. Reserved Datasheet Integrated Intel(R) High Definition Audio (Intel(R) HD Audio) Controller Registers Bit Description 8 PME Enable (PMEE)--R/W. 0 = Disable 1 = When set and if corresponding PMES also set, the Intel High Definition Audio controller sets the PME_B0_STS bit in the GPE0_STS register (PMBASE +28h). This bit is in the resume well and is cleared on a power-on reset. Software must not make assumptions about the reset state of this bit and must set it appropriately. 7:2 Reserved 1:0 Power State (PS)--R/W. This field is used both to determine the current power state of the Intel High Definition Audio controller and to set a new power state. 00 = D0 state 11 = D3HOT state Others = reserved Notes: 1. If software attempts to write a value of 01b or 10b in to this field, the write operation must complete normally; however, the data is discarded and no state change occurs. 2. When in the D3HOT states, the Intel High Definition Audio controller's configuration space is available, but the I/O and memory space are not. Additionally, interrupts are blocked. 3. When software changes this value from D3HOT state to the D0 state, an internal warm (soft) reset is generated, and software must re-initialize the function. 17.1.1.25 MID--MSI Capability ID Register (Intel(R) High Definition Audio Controller--D27:F0) Address Offset: 60h-61h Default Value: 7005h Bit 15:8 7:0 17.1.1.26 Attribute: Size: Description Next Capability (Next)--RO. Hardwired to 70h. Points to the PCI Express* capability structure. Cap ID (CAP)--RO. Hardwired to 05h. Indicates that this pointer is a MSI capability. MMC--MSI Message Control Register (Intel(R) High Definition Audio Controller--D27:F0) Address Offset: 62h-63h Default Value: 0080h Bit 15:8 Attribute: Size: RO, R/W 16 bits Description Reserved 7 64b Address Capability (64ADD)--RO. Hardwired to 1. Indicates the ability to generate a 64-bit message address. 6:4 Multiple Message Enable (MME)--RO. Normally this is a R/W register. However since only 1 message is supported, these bits are hardwired to 000 = 1 message. 3:1 0 Datasheet RO 16 bits Multiple Message Capable (MMC)--RO. Hardwired to 0 indicating request for 1 message. MSI Enable (ME)--R/W. 0 = an MSI may not be generated 1 = an MSI will be generated instead of an INTx signal. 631 Integrated Intel(R) High Definition Audio (Intel(R) HD Audio) Controller Registers 17.1.1.27 MMLA--MSI Message Lower Address Register (Intel(R) High Definition Audio Controller--D27:F0) Address Offset: 64h-67h Default Value: 00000000h Bit 31:2 1:0 17.1.1.28 Attribute: Size: Description Message Lower Address (MLA)--R/W. Lower address used for MSI message. Reserved MMUA--MSI Message Upper Address Register (Intel(R) High Definition Audio Controller--D27:F0) Address Offset: 68h-6Bh Default Value: 00000000h Bit 31:0 17.1.1.29 Attribute: Size: Message Upper Address (MUA)--R/W. Upper 32-bits of address used for MSI message. MMD--MSI Message Data Register (Intel(R) High Definition Audio Controller--D27:F0) Bit 15:0 Attribute: Size: Message Data (MD)--R/W. Data used for MSI message. PXID--PCI Express* Capability ID Register (Intel(R) High Definition Audio Controller--D27:F0) Bit 15:8 7:0 Attribute: Size: RO 16 bits Description Next Capability (Next)--RO. Hardwired to 0. Indicates that this is the last capability structure in the list. Cap ID (CAP)--RO. Hardwired to 10h. Indicates that this pointer is a PCI Express* capability structure. PXC--PCI Express* Capabilities Register (Intel(R) High Definition Audio Controller--D27:F0) Address Offset: 72h-73h Default Value: 0091h Bit 15:14 13:9 8 632 R/W 16 bits Description Address Offset: 70h-71h Default Value: 0010h 17.1.1.31 R/W 32 bits Description Address Offset: 6Ch-6Dh Default Value: 0000h 17.1.1.30 RO, R/W 32 bits Attribute: Size: RO 16 bits Description Reserved Interrupt Message Number (IMN)--RO. Hardwired to 0. Slot Implemented (SI)--RO. Hardwired to 0. 7:4 Device/Port Type (DPT)--RO. Hardwired to 1001b. Indicates that this is a Root Complex Integrated endpoint device. 3:0 Capability Version (CV)--RO. Hardwired to 0001b. Indicates version #1 PCI Express capability Datasheet Integrated Intel(R) High Definition Audio (Intel(R) HD Audio) Controller Registers 17.1.1.32 DEVCAP--Device Capabilities Register (Intel(R) High Definition Audio Controller--D27:F0) Address Offset: 74h-77h Default Value: 10000000h Function Level Reset: No Bit 31:29 28 Reserved Function Level Reset (FLR)--R/WL. A 1 indicates that the PCH HD Audio Controller supports the Function Level Reset Capability. Locked when HDCTL.BCLD = 1. Captured Slot Power Limit Scale (SPLS)--RO. Hardwired to 0. 25:18 Captured Slot Power Limit Value (SPLV)--RO. Hardwired to 0. 17:15 Reserved 14 Power Indicator Present--RO. Hardwired to 0. 13 Attention Indicator Present--RO. Hardwired to 0. 12 8:6 5 R/WO, RO 32 bits Description 27:26 11:9 17.1.1.33 Attribute: Size: Attention Button Present--RO. Hardwired to 0. Endpoint L1 Acceptable Latency--R/WL. BIOS must write to this bit field during boot. Locked when HDCTL.BCLD = 1. Endpoint L0s Acceptable Latency--R/WL. BIOS must write to this bit field during boot. Locked when HDCTL.BCLD = 1. Extended Tag Field Support--RO. Hardwired to 0. Indicates 5-bit tag field support 4:3 Phantom Functions Supported--RO. Hardwired to 0. Indicates that phantom functions not supported. 2:0 Max Payload Size Supported--RO. Hardwired to 0. Indicates 128-B maximum payload size capability. DEVC--Device Control Register (Intel(R) High Definition Audio Controller--D27:F0) Address Offset: 78h-79h Default Value: 0800h Function Level Reset:No (Bit 11 Only) Bit 15 14:12 11 Attribute: Size: R/W, RO 16 bits Description Initiate FLR (IF)--R/W. This bit is used to initiate FLR transition. 1 = A write of 1 initiates FLR transition. Since hardware does not respond to any cycles until FLR completion, the read value by software from this bit is 0. Max Read Request Size--RO. Hardwired to 0 enabling 128B maximum read request size. No Snoop Enable (NSNPEN)--R/W. 0 = The Intel High Definition Audio controller will not set the No Snoop bit. In this case, isochronous transfers will not use VC1 (VCi) even if it is enabled since VC1 is never snooped. Isochronous transfers will use VC0. 1 = The Intel High Definition Audio controller is permitted to set the No Snoop bit in the Requester Attributes of a bus master transaction. In this case, VC0 or VC1 may be used for isochronous transfers. Note: This bit is not reset on D3HOT to D0 transition; however, it is reset by PLTRST#. This bit is not reset by Function Level Reset. 10 Datasheet Auxiliary Power Enable--RO. Hardwired to 0, indicating that Intel High Definition Audio device does not draw AUX power 9 Phantom Function Enable--RO. Hardwired to 0 disabling phantom functions. 8 Extended Tag Field Enable--RO. Hardwired to 0 enabling 5-bit tag. 633 Integrated Intel(R) High Definition Audio (Intel(R) HD Audio) Controller Registers Bit 7:5 4 17.1.1.34 Description Max Payload Size--RO. Hardwired to 0 indicating 128B. Enable Relaxed Ordering--RO. Hardwired to 0 disabling relaxed ordering. 3 Unsupported Request Reporting Enable--R/W. Not implemented. 2 Fatal Error Reporting Enable--R/W. Not implemented. 1 Non-Fatal Error Reporting Enable--R/W. Not implemented. 0 Correctable Error Reporting Enable--R/W. Not implemented. DEVS--Device Status Register (Intel(R) High Definition Audio Controller--D27:F0) Address Offset: 7Ah-7Bh Default Value: 0010h Bit 15:6 17.1.1.35 Attribute: Size: Description Reserved 5 Transactions Pending--RO. 0 = Indicates that completions for all non-posted requests have been received 1 = Indicates that Intel High Definition Audio controller has issued non-posted requests which have not been completed. 4 AUX Power Detected--RO. Hardwired to 1 indicating the device is connected to resume power 3 Unsupported Request Detected--RO. Not implemented. Hardwired to 0. 2 Fatal Error Detected--RO. Not implemented. Hardwired to 0. 1 Non-Fatal Error Detected--RO. Not implemented. Hardwired to 0. 0 Correctable Error Detected--RO. Not implemented. Hardwired to 0. VCCAP--Virtual Channel Enhanced Capability Header (Intel(R) High Definition Audio Controller--D27:F0) Address Offset: 100h-103h Default Value: 13010002h Bit 634 RO 16 bits Attribute: Size: R/WO 32 bits Description 31:20 Next Capability Offset--R/WL. Points to the next capability header. 130h = Root Complex Link Declaration Enhanced Capability Header 000h = Root Complex Link Declaration Enhanced Capability Header is not supported. Locked when HDCTL.BCLD = 1. 19:16 Capability Version--R/WL. 0h =PCI Express Virtual channel capability and the Root Complex Topology Capability structure are not supported. 1h =PCI Express Virtual channel capability and the Root Complex Topology Capability structure are supported. Locked when HDCTL.BCLD = 1. 15:0 PCI Express* Extended Capability--R/WL. 0000h =PCI Express Virtual channel capability and the Root Complex Topology Capability structure are not supported. 0002h =PCI Express Virtual channel capability and the Root Complex Topology Capability structure are supported. Locked when HDCTL.BCLD = 1. Datasheet Integrated Intel(R) High Definition Audio (Intel(R) HD Audio) Controller Registers 17.1.1.36 PVCCAP1--Port VC Capability Register 1 (Intel(R) High Definition Audio Controller--D27:F0) Address Offset: 104h-107h Default Value: 00000001h Bit 31:12 11:10 9:8 7 6:4 3 2:0 17.1.1.37 Attribute: Size: Description Reserved Port Arbitration Table Entry Size--RO. Hardwired to 0 since this is an endpoint device. Reference Clock--RO. Hardwired to 0 since this is an endpoint device. Reserved Low Priority Extended VC Count--RO. Hardwired to 0. Indicates that only VC0 belongs to the low priority VC group. Reserved Extended VC Count--RO. Hardwired to 001b. Indicates that 1 extended VC (in addition to VC0) is supported by the Intel High Definition Audio controller. PVCCAP2--Port VC Capability Register 2 (Intel(R) High Definition Audio Controller--D27:F0) Address Offset: 108h-10Bh Default Value: 00000000h Attribute: Size: Description 31:24 VC Arbitration Table Offset--RO. Hardwired to 0 indicating that a VC arbitration table is not present. 7:0 Reserved VC Arbitration Capability--RO. Hardwired to 0. These bits are not applicable since the Intel High Definition Audio controller reports a 0 in the Low Priority Extended VC Count bits in the PVCCAP1 register. PVCCTL--Port VC Control Register (Intel(R) High Definition Audio Controller--D27:F0) Address Offset: 10Ch-10Dh Default Value: 0000h Bit 15:4 3:1 0 17.1.1.39 Attribute: Size: RO 16 bits Description Reserved VC Arbitration Select--RO. Hardwired to 0. Normally these bits are R/W. However, these bits are not applicable since the Intel High Definition Audio controller reports a 0 in the Low Priority Extended VC Count bits in the PVCCAP1 register. Load VC Arbitration Table--RO. Hardwired to 0 since an arbitration table is not present. PVCSTS--Port VC Status Register (Intel(R) High Definition Audio Controller--D27:F0) Address Offset: 10Eh-10Fh Default Value: 0000h Bit 15:1 0 Datasheet RO 32 bits Bit 23:8 17.1.1.38 RO 32 bits Attribute: Size: RO 16 bits Description Reserved VC Arbitration Table Status--RO. Hardwired to 0 since an arbitration table is not present. 635 Integrated Intel(R) High Definition Audio (Intel(R) HD Audio) Controller Registers 17.1.1.40 VC0CAP--VC0 Resource Capability Register (Intel(R) High Definition Audio Controller--D27:F0) Address Offset: 110h-113h Default Value: 00000000h Bit 31:24 23 22:16 Description Port Arbitration Table Offset--RO. Hardwired to 0 since this field is not valid for endpoint devices Reserved Maximum Time Slots--RO. Hardwired to 0 since this field is not valid for endpoint devices. Reject Snoop Transactions--RO. Hardwired to 0 since this field is not valid for endpoint devices. 14 Advanced Packet Switching--RO. Hardwired to 0 since this field is not valid for endpoint devices. 7:0 Reserved Port Arbitration Capability--RO. Hardwired to 0 since this field is not valid for endpoint devices. VC0CTL--VC0 Resource Control Register (Intel(R) High Definition Audio Controller--D27:F0) Address Offset: 114h-117h Default Value: 800000FFh Function Level Reset: No Bit 31 30:27 Attribute: Size: VC0 Enable--RO. Hardwired to 1 for VC0. Reserved VC0 ID--RO. Hardwired to 0 since the first VC is always assigned as VC0. 23:20 Reserved 16 15:8 7:0 Port Arbitration Select--RO. Hardwired to 0 since this field is not valid for endpoint devices. Load Port Arbitration Table--RO. Hardwired to 0 since this field is not valid for endpoint devices. Reserved TC/VC0 Map--R/W, RO. Bit 0 is hardwired to 1 since TC0 is always mapped VC0. Bits [7:1] are implemented as R/W bits. VC0STS--VC0 Resource Status Register (Intel(R) High Definition Audio Controller--D27:F0) Address Offset: 11Ah-11Bh Default Value: 0000h Bit 15:2 636 R/W, RO 32 bits Description 26:24 19:17 17.1.1.42 RO 32 bits 15 13:8 17.1.1.41 Attribute: Size: Attribute: Size: RO 16 bits Description Reserved 1 VC0 Negotiation Pending--RO. Hardwired to 0 since this bit does not apply to the integrated Intel High Definition Audio device. 0 Port Arbitration Table Status--RO. Hardwired to 0 since this field is not valid for endpoint devices. Datasheet Integrated Intel(R) High Definition Audio (Intel(R) HD Audio) Controller Registers 17.1.1.43 VCiCAP--VCi Resource Capability Register (Intel(R) High Definition Audio Controller--D27:F0) Address Offset: 11Ch-11Fh Default Value: 00000000h Bit 31:24 23 22:16 Description Port Arbitration Table Offset--RO. Hardwired to 0 since this field is not valid for endpoint devices. Reserved Maximum Time Slots--RO. Hardwired to 0 since this field is not valid for endpoint devices. Reject Snoop Transactions--RO. Hardwired to 0 since this field is not valid for endpoint devices. 14 Advanced Packet Switching--RO. Hardwired to 0 since this field is not valid for endpoint devices. 7:0 Reserved Port Arbitration Capability--RO. Hardwired to 0 since this field is not valid for endpoint devices. VCiCTL--VCi Resource Control Register (Intel(R) High Definition Audio Controller--D27:F0) Address Offset: 120h-123h Default Value: 00000000h Function Level Reset: No Bit 31 Attribute: Size: VCi Enable--R/W. 0 = VCi is disabled 1 = VCi is enabled This bit is not reset on D3HOT to D0 transition; however, it is reset by PLTRST#. 30:27 Reserved 26:24 VCi ID--R/W. This field assigns a VC ID to the VCi resource. This field is not used by the PCH hardware, but it is R/W to avoid confusing software. 23:20 Reserved 19:17 16 15:8 7:0 Port Arbitration Select--RO. Hardwired to 0 since this field is not valid for endpoint devices. Load Port Arbitration Table--RO. Hardwired to 0 since this field is not valid for endpoint devices. Reserved TC/VCi Map--R/W, RO. This field indicates the TCs that are mapped to the VCi resource. Bit 0 is hardwired to 0 indicating that it cannot be mapped to VCi. Bits [7:1] are implemented as R/W bits. This field is not used by the PCH hardware, but it is R/W to avoid confusing software. VCiSTS--VCi Resource Status Register (Intel(R) High Definition Audio Controller--D27:F0) Address Offset: 126h-127h Default Value: 0000h Bit 15:2 Datasheet R/W, RO 32 bits Description Note: 17.1.1.45 RO 32 bits 15 13:8 17.1.1.44 Attribute: Size: Attribute: Size: RO 16 bits Description Reserved 1 VCi Negotiation Pending--RO. Does not apply. Hardwired to 0. 0 Port Arbitration Table Status--RO. Hardwired to 0 since this field is not valid for endpoint devices. 637 Integrated Intel(R) High Definition Audio (Intel(R) HD Audio) Controller Registers 17.1.1.46 RCCAP--Root Complex Link Declaration Enhanced Capability Header Register (Intel(R) High Definition Audio Controller--D27:F0) Address Offset: 130h-133h Default Value: 00010005h Bit Description Next Capability Offset--RO. Hardwired to 0 indicating this is the last capability. 19:16 Capability Version--RO. Hardwired to 1h. PCI Express* Extended Capability ID--RO. Hardwired to 0005h. ESD--Element Self Description Register (Intel(R) High Definition Audio Controller--D27:F0) Address Offset: 134h-137h Default Value: 0F000100h Bit Attribute: Size: Description Port Number--RO. Hardwired to 0Fh indicating that the Intel High Definition Audio controller is assigned as Port #15d. 23:16 Component ID--RL. This field returns the value of the ESD.CID field of the chip configuration section. ESD.CID is programmed by BIOS. Locked when HDCTL.BCLD = 1. Number of Link Entries--RO. The Intel High Definition Audio only connects to one device, the PCH egress port. Therefore, this field reports a value of 1h. 7:4 Reserved 3:0 Element Type (ELTYP)--RO. The Intel High Definition Audio controller is an integrated Root Complex Device. Therefore, the field reports a value of 0h. L1DESC--Link 1 Description Register (Intel(R) High Definition Audio Controller--D27:F0) Address Offset: 140h-143h Default Value: 00000001h Bit Attribute: Size: Description Target Port Number--RO. The Intel High Definition Audio controller targets the PCH's Port 0. 23:16 Target Component ID--RO. This field returns the value of the ESD.CID field of the chip configuration section. ESD.CID is programmed by BIOS. Reserved 1 Link Type--RO. Hardwired to 0 indicating Type 0. 0 Link Valid--RO. Hardwired to 1. L1ADDL--Link 1 Lower Address Register (Intel(R) High Definition Audio Controller--D27:F0) Address Offset: 148h-14Bh Default Value: See Register Description Bit 31:14 638 RO 32 bits 31:24 15:2 17.1.1.49 RO 32 bits 31:24 15:8 17.1.1.48 RO 32 bits 31:20 15:0 17.1.1.47 Attribute: Size: Attribute: Size: RO 32 bits Description Link 1 Lower Address--RO. Hardwired to match the RCBA register value in the PCI-LPC bridge (D31:F0:F0h). Datasheet Integrated Intel(R) High Definition Audio (Intel(R) HD Audio) Controller Registers Bit 13:0 17.1.1.50 Description Reserved L1ADDU--Link 1 Upper Address Register (Intel(R) High Definition Audio Controller--D27:F0) Address Offset: 14Ch-14Fh Default Value: 00000000h Bit 31:0 Datasheet Attribute: Size: RO 32 bits Description Link 1 Upper Address--RO. Hardwired to 00000000h. 639 Integrated Intel(R) High Definition Audio (Intel(R) HD Audio) Controller Registers 17.1.2 Intel(R) High Definition Audio Memory Mapped Configuration Registers (Intel(R) High Definition Audio D27:F0) The base memory location for these memory mapped configuration registers is specified in the HdBAR register (D27:F0:offset 10h and D27:F0:offset 14h). The individual registers are then accessible at HdBAR + Offset as indicated in Table 17-1. These memory mapped registers must be accessed in byte, word, or DWord quantities. Note: Address locations that are not shown should be treated as Reserved. Table 17-1. Intel(R) High Definition Audio Memory Mapped Configuration Registers Address Map (Intel(R) High Definition Audio D27:F0) (Sheet 1 of 4) 640 HdBAR + Offset Mnemonic 00h-01h GCAP Global Capabilities 02h VMIN Minor Version Register Name 03h VMAJ 04h-05h OUTPAY 06h-07h INPAY Input Payload Capability 08h-0Bh GCTL Global Control 0Ch-0Dh WAKEEN 0Eh-0Fh STATESTS 10h-11h GSTS 12h-13h GCAP2 18h-19h OUTSTRMPAY 1Ah-1Bh INSTRMPAY 1Ch-1Fh -- 20h-23h INTCTL Major Version Output Payload Capability Default Attribute 4401h RO, R/WO 00h RO 01h RO 003Ch RO 001Dh RO 00000000h R/W Wake Enable 0000h R/W State Change Status 0000h R/WC Global Status 0000h R/WC Global Capabilities 2 0001h R/WL Output Stream Payload Capability 0030h RO Input Stream Payload Capability 0018h RO Reserved 00000000h RO Interrupt Control 00000000h R/W 24h-27h INTSTS Interrupt Status 00000000h RO 30h-33h WALCLK Wall Clock Counter 00000000h RO 38h-3Bh SSYNC 40h-43h CORBLBASE Stream Synchronization 00000000h R/W CORB Lower Base Address 00000000h R/W, RO 44h-47h CORBUBASE 48h-49h CORBWP CORB Write Pointer CORB Upper Base Address 00000000h R/W 0000h R/W 4Ah-4Bh CORBRP CORB Read Pointer 4Ch CORBCTL CORB Control 0000h R/W, RO 00h R/W 4Dh CORBST 4Eh CORBSIZE CORB Status 00h R/WC CORB Size 42h RO 50h-53h RIRBLBASE RIRB Lower Base Address 00000000h R/W, RO 54h-57h RIRBUBASE RIRB Upper Base Address 00000000h R/W 58h-59h RIRBWP RIRB Write Pointer 0000h R/W, RO 5Ah-5Bh RINTCNT Response Interrupt Count 0000h R/W 5Ch RIRBCTL RIRB Control 00h R/W 5Dh RIRBSTS RIRB Status 00h R/WC Datasheet Integrated Intel(R) High Definition Audio (Intel(R) HD Audio) Controller Registers Table 17-1. Intel(R) High Definition Audio Memory Mapped Configuration Registers Address Map (Intel(R) High Definition Audio D27:F0) (Sheet 2 of 4) Datasheet HdBAR + Offset Mnemonic 5Eh RIRBSIZE 60h-63h IC 64h-67h IR 68h-69h ICS 70h-73h DPLBASE 74h-77h 80h-82h Register Name Default Attribute 42h RO Immediate Command 00000000h R/W Immediate Response 00000000h RO RIRB Size Immediate Command Status 0000h R/W, R/WC DMA Position Lower Base Address 00000000h R/W, RO DPUBASE DMA Position Upper Base Address 00000000h R/W ISD0CTL Input Stream Descriptor Control 040000h R/W, RO 83h ISD0STS ISD0 Status 00h R/WC, RO 84h-87h ISD0LPIB ISD0 Link Position in Buffer 00000000h RO 88h-8Bh ISD0CBL ISD0 Cyclic Buffer Length 00000000h R/W 8Ch-8Dh ISD0LVI ISD0 Last Valid Index 0000h R/W 8Eh-8F ISD0FIFOW ISD0 FIFO Watermark 0004h R/W 90h-91h ISD0FIFOS ISD0 FIFO Size 0000h R/W 92h-93h ISD0FMT ISD0 Format 0000h R/W 98h-9Bh ISD0BDPL ISD0 Buffer Descriptor List Pointer -Lower Base Address 00000000h R/W, RO 9Ch-9Fh ISD0BDPU ISD0 Buffer Description List Pointer -Upper Base Address 00000000h R/W A0h-A2h ISD1CTL Input Stream Descriptor 1(ISD1) Control 040000h R/W, RO A3h ISD1STS ISD1 Status 00h R/WC, RO A4h-A7h ISD1LPIB ISD1 Link Position in Buffer 00000000h RO 00000000h R/W 0000h R/W A8h-ABh ISD1CBL ISD1 Cyclic Buffer Length ACh-ADh ISD1LVI ISD1 Last Valid Index AEh-AFh ISD1FIFOW ISD1 FIFO Watermark 0004h R/W B0h-B1h ISD1FIFOS ISD1 FIFO Size 0000h R/W B2h-B3h ISD1FMT ISD1 Format 0000h R/W B8h-BBh ISD1BDPL ISD1 Buffer Descriptor List Pointer -Lower Base Address 00000000h R/W, RO BCh-BFh ISD1BDPU ISD1 Buffer Description List Pointer -Upper Base Address 00000000h R/W C0h-C2h ISD2CTL Input Stream Descriptor 2 (ISD2) Control 040000h R/W, RO C3h ISD2STS ISD2 Status 00h R/WC, RO C4h-C7h ISD2LPIB ISD2 Link Position in Buffer 00000000h RO 00000000h R/W 0000h R/W C8h-CBh ISD2CBL ISD2 Cyclic Buffer Length CCh-CDh ISD2LVI ISD2 Last Valid Index CEh-CFh ISD1FIFOW ISD1 FIFO Watermark 0004h R/W D0h-D1h ISD2FIFOS ISD2 FIFO Size 0000h R/W D2h-D3h ISD2FMT ISD2 Format 0000h R/W D8h-dBh ISD2BDPL ISD2 Buffer Descriptor List Pointer -Lower Base Address 00000000h R/W, RO DCh-DFh ISD2BDPU ISD2 Buffer Description List Pointer -Upper Base Address 00000000h R/W 641 Integrated Intel(R) High Definition Audio (Intel(R) HD Audio) Controller Registers Table 17-1. Intel(R) High Definition Audio Memory Mapped Configuration Registers Address Map (Intel(R) High Definition Audio D27:F0) (Sheet 3 of 4) 642 HdBAR + Offset Mnemonic E0h-E2h ISD3CTL Register Name Input Stream Descriptor 3 (ISD3) Control Default Attribute 040000h R/W, RO E3h ISD3STS ISD3 Status 00h R/WC, RO E4h-E7h ISD3LPIB ISD3 Link Position in Buffer 00000000h RO E8h-EBh ISD3CBL ISD3 Cyclic Buffer Length 00000000h R/W ECh-EDh ISD3LVI ISD3 Last Valid Index 0000h R/W EEh-EFh ISD3FIFOW ISD3 FIFO Watermark 0004h R/W F0h-F1h ISD3FIFOS ISD3 FIFO Size 0000h R/W F2h-F3h ISD3FMT ISD3 Format 0000h R/W F8h-FBh ISD3BDPL ISD3 Buffer Descriptor List Pointer -Lower Base Address 00000000h R/W, RO FCh-FFh ISD3BDPU ISD3 Buffer Description List Pointer -Upper Base Address 00000000h R/W 100h-102h OSD0CTL Output Stream Descriptor 0 (OSD0) Control 040000h R/W, RO 103h OSD0STS OSD0 Status 00h R/WC, RO 104h-107h OSD0LPIB OSD0 Link Position in Buffer 00000000h RO 00000000h R/W 0000h R/W 108h-10Bh OSD0CBL OSD0 Cyclic Buffer Length 10Ch-10Dh OSD0LVI OSD0 Last Valid Index 10Eh-10Fh OSD0FIFOW OSD0 FIFO Watermark 0004h R/W 110h-111h OSD0FIFOS OSD0 FIFO Size 0000h R/W 112-113h OSD0FMT OSD0 Format 0000h R/W 118h-11Bh OSD0BDPL OSD0 Buffer Descriptor List Pointer -Lower Base Address 00000000h R/W, RO 11Ch-11Fh OSD0BDPU OSD0 Buffer Description List Pointer -Upper Base Address 00000000h R/W 120h-122h OSD1CTL Output Stream Descriptor 1 (OSD1) Control 040000h R/W, RO 123h OSD1STS OSD1 Status 00h R/WC, RO 124h-127h OSD1LPIB OSD1 Link Position in Buffer 00000000h RO 00000000h R/W 0000h R/W 128h-12Bh OSD1CBL OSD1 Cyclic Buffer Length 12Ch-12Dh OSD1LVI OSD1 Last Valid Index 12Eh-12Fh OSD1FIFOW OSD1 FIFO Watermark 0004h R/W 130h-131h OSD1FIFOS OSD1 FIFO Size 0000h R/W 132h-133h OSD1FMT OSD1 Format 0000h R/W 138h-13Bh OSD1BDPL OSD1 Buffer Descriptor List Pointer -Lower Base Address 00000000h R/W, RO 13Ch-13Fh OSD1BDPU OSD1 Buffer Description List Pointer -Upper Base Address 00000000h R/W 140h-142h OSD2CTL Output Stream Descriptor 2 (OSD2) Control 040000h R/W, RO 143h OSD2STS OSD2 Status 00h R/WC, RO 144h-147h OSD2LPIB OSD2 Link Position in Buffer 00000000h RO 148h-14Bh OSD2CBL OSD2 Cyclic Buffer Length 00000000h R/W 14Ch-14Dh OSD2LVI OSD2 Last Valid Index 0000h R/W 14Eh-14Fh OSD2FIFOW OSD2 FIFO Watermark 0004h R/W Datasheet Integrated Intel(R) High Definition Audio (Intel(R) HD Audio) Controller Registers Table 17-1. Intel(R) High Definition Audio Memory Mapped Configuration Registers Address Map (Intel(R) High Definition Audio D27:F0) (Sheet 4 of 4) 17.1.2.1 HdBAR + Offset Mnemonic 150h-151h OSD2FIFOS Register Name OSD2 FIFO Size Attribute 0000h R/W 152h-153h OSD2FMT OSD2 Format 0000h R/W 158h-15Bh OSD2BDPL OSD2 Buffer Descriptor List Pointer -Lower Base Address 00000000h R/W, RO 15Ch-15Fh OSD2BDPU OSD2 Buffer Description List Pointer -Upper Base Address 00000000h R/W 160h-162h OSD3CTL Output Stream Descriptor 3 (OSD3) Control 040000h R/W, RO 163h OSD3STS OSD3 Status 00h R/WC, RO 164h-167h OSD3LPIB OSD3 Link Position in Buffer 00000000h RO 00000000h R/W 0000h R/W 168h-16Bh OSD3CBL OSD3 Cyclic Buffer Length 16Ch-16Dh OSD3LVI OSD3 Last Valid Index 16Eh-16Fh OSD3FIFOW OSD3 FIFO Watermark 0004h R/W 170h-171h OSD3FIFOS OSD3 FIFO Size 0000h R/W 172h-173h OSD3FMT OSD3 Format 0000h R/W 178h-17Bh OSD3BDPL OSD3 Buffer Descriptor List Pointer -Lower Base Address 00000000h R/W, RO 17Ch-17Fh OSD3BDPU OSD3 Buffer Description List Pointer -Upper Base Address 00000000h R/W GCAP--Global Capabilities Register (Intel(R) High Definition Audio Controller--D27:F0) Memory Address:HdBAR + 00h Default Value: 4401h Bit 15:12 Datasheet Default Attribute: Size: RO, R/WO 16 bits Description Number of Output Stream Supported--R/WL. 0100b indicates that the PCH's Intel High Definition Audio controller supports 4 output streams. Locked when HDCTL.BCLD = 1. 11:8 Number of Input Stream Supported--R/WL. 0100b indicates that the PCH's Intel High Definition Audio controller supports 4 input streams. Locked when HDCTL.BCLD = 1. 7:3 Number of Bidirectional Stream Supported--RO. Hardwired to 0 indicating that the PCH's Intel High Definition Audio controller supports 0 bidirectional stream. 2:1 Number of Serial Data Out Signals--RO. Hardwired to 0 indicating that the PCH's Intel High Definition Audio controller supports 1 serial data output signal. 0 64-bit Address Supported--R/WL. 1b indicates that the PCH's Intel High Definition Audio controller supports 64-bit addressing for BDL addresses, data buffer addressees, and command buffer addresses. Locked when HDCTL.BCLD = 1. 643 Integrated Intel(R) High Definition Audio (Intel(R) HD Audio) Controller Registers 17.1.2.2 VMIN--Minor Version Register (Intel(R) High Definition Audio Controller--D27:F0) Memory Address:HdBAR + 02h Default Value: 00h 17.1.2.3 Attribute: Size: Bit Description 7:0 Minor Version--RO. Hardwired to 0 indicating that the PCH supports minor revision number 00h of the Intel High Definition Audio specification. VMAJ--Major Version Register (Intel(R) High Definition Audio Controller--D27:F0) Memory Address:HdBAR + 03h Default Value: 01h 17.1.2.4 Attribute: Size: Description 7:0 Major Version--RO. Hardwired to 01h indicating that the PCH supports major revision number 1 of the Intel High Definition Audio specification. OUTPAY--Output Payload Capability Register (Intel(R) High Definition Audio Controller--D27:F0) Bit 15:7 6:0 Attribute: Size: RO 16 bits Description Reserved Output Payload Capability--RO. Hardwired to 3Ch indicating 60 word payload. This field indicates the total output payload available on the link. This does not include bandwidth used for command and control. This measurement is in 16-bit word quantities per 48 MHz frame. The default link clock of 24.000 MHz (the data is double pumped) provides 1000 bits per frame, or 62.5 words in total. 40 bits are used for command and control, leaving 60 words available for data payload. 00h = 0 word 01h = 1 word payload. ..... FFh = 256 word payload. INPAY--Input Payload Capability Register (Intel(R) High Definition Audio Controller--D27:F0) Memory Address:HdBAR + 06h Default Value: 001Dh Bit 15:7 6:0 644 RO 8 bits Bit Memory Address:HdBAR + 04h Default Value: 003Ch 17.1.2.5 RO 8 bits Attribute: Size: RO 16 bits Description Reserved Input Payload Capability--RO. Hardwired to 1Dh indicating 29 word payload. This field indicates the total output payload available on the link. This does not include bandwidth used for response. This measurement is in 16-bit word quantities per 48 MHz frame. The default link clock of 24.000 MHz provides 500 bits per frame, or 31.25 words in total. 36 bits are used for response, leaving 29 words available for data payload. 00h = 0 word 01h = 1 word payload. ..... FFh = 256 word payload. Datasheet Integrated Intel(R) High Definition Audio (Intel(R) HD Audio) Controller Registers 17.1.2.6 GCTL--Global Control Register (Intel(R) High Definition Audio Controller--D27:F0) Memory Address:HdBAR + 08h Default Value: 00000000h Bit 31:9 8 7:2 Datasheet Attribute: Size: R/W 32 bits Description Reserved Accept Unsolicited Response Enable--R/W. 0 = Unsolicited responses from the codecs are not accepted. 1 = Unsolicited response from the codecs are accepted by the controller and placed into the Response Input Ring Buffer. Reserved 1 Flush Control--R/W. Writing a 1 to this bit initiates a flush. When the flush completion is received by the controller, hardware sets the Flush Status bit and clears this Flush Control bit. Before a flush cycle is initiated, the DMA Position Buffer must be programmed with a valid memory address by software, but the DMA Position Buffer bit 0 needs not be set to enable the position reporting mechanism. Also, all streams must be stopped (the associated RUN bit must be 0). When the flush is initiated, the controller will flush the pipelines to memory to ensure that the hardware is ready to transition to a D3 state. Setting this bit is not a critical step in the power state transition if the content of the FIFOs is not critical. 0 Controller Reset #--R/W. 0 = Writing a 0 causes the Intel High Definition Audio controller to be reset. All state machines, FIFOs, and non-resume well memory mapped configuration registers (not PCI configuration registers) in the controller will be reset. The Intel High Definition Audio link RESET# signal will be asserted, and all other link signals will be driven to their default values. After the hardware has completed sequencing into the reset state, it will report a 0 in this bit. Software must read a 0 from this bit to verify the controller is in reset. 1 = Writing a 1 causes the controller to exit its reset state and de-assert the Intel High Definition Audio link RESET# signal. Software is responsible for setting/clearing this bit such that the minimum Intel High Definition Audio link RESET# signal assertion pulse width specification is met. When the controller hardware is ready to begin operation, it will report a 1 in this bit. Software must read a 1 from this bit before accessing any controller registers. This bit defaults to a 0 after Hardware reset, therefore, software needs to write a 1 to this bit to begin operation. Notes: 1. The CORB/RIRB RUN bits and all stream RUN bits must be verified cleared to 0 before writing a 0 to this bit in order to assure a clean re-start. 2. When setting or clearing this bit, software must ensure that minimum link timing requirements (minimum RESET# assertion time, and so on) are met. 3. When this bit is 0 indicating that the controller is in reset, writes to all Intel High Definition Audio memory mapped registers are ignored as if the device is not present. The only exception is this register itself. The Global Control register is write-able as a DWord, Word, or Byte even when CRST# (this bit) is 0 if the byte enable for the byte containing the CRST# bit (Byte Enable 0) is active. If Byte Enable 0 is not active, writes to the Global Control register will be ignored when CRST# is 0. When CRST# is 0, reads to Intel High Definition Audio memory mapped registers will return their default value except for registers that are not reset with PLTRST# or on a D3HOT to D0 transition. 645 Integrated Intel(R) High Definition Audio (Intel(R) HD Audio) Controller Registers 17.1.2.7 WAKEEN--Wake Enable Register (Intel(R) High Definition Audio Controller--D27:F0) Memory Address:HdBAR + 0Ch Default Value: 0000h Function Level Reset:No Bit 15:4 3:0 17.1.2.8 Attribute: Size: Description Reserved SDIN Wake Enable Flags--R/W. These bits control which SDI signal(s) may generate a wake event. A 1b in the bit mask indicates that the associated SDIN signal is enabled to generate a wake. Bit 0 is used for SDI[0] Bit 1 is used for SDI[1] Bit 2 is used for SDI[2] Bit 3 is used for SDI[3] Note: These bits are in the resume well and only cleared on a power on reset. Software must not make assumptions about the reset state of these bits and must set them appropriately. STATESTS--State Change Status Register (Intel(R) High Definition Audio Controller--D27:F0) Memory Address:HdBAR + 0Eh Default Value: 0000h Function Level Reset:No Bit 15:4 3:0 17.1.2.9 Attribute: Size: R/WC 16 bits Description Reserved SDIN State Change Status Flags--R/WC. Flag bits that indicate which SDI signal(s) received a state change event. The bits are cleared by writing 1s to them. Bit 0 = SDI[0] Bit 1 = SDI[1] Bit 2 = SDI[2] Bit 3 = SDI[3] These bits are in the resume well and only cleared on a power on reset. Software must not make assumptions about the reset state of these bits and must set them appropriately. GSTS--Global Status Register (Intel(R) High Definition Audio Controller--D27:F0) Memory Address:HdBAR + 10h Default Value: 0000h Bit 15:2 646 R/W 16 bits Attribute: Size: R/WC 16 bits Description Reserved 1 Flush Status--R/WC. This bit is set to 1 by hardware to indicate that the flush cycle initiated when the Flush Control bit (HdBAR + 08h, bit 1) was set has completed. Software must write a 1 to clear this bit before the next time the Flush Control bit is set to clear the bit. 0 Reserved Datasheet Integrated Intel(R) High Definition Audio (Intel(R) HD Audio) Controller Registers 17.1.2.10 GCAP2 Global Capabilities 2 Register (Intel(R) High Definition Audio Controller--D27:F0) Memory Address:HdBAR + 12h Default Value: 0001h Bit 15:1 0 17.1.2.11 Attribute: Size: Description Reserved Energy Efficient Audio Capability (EEAC)--R/WL. Indicates whether the energy efficient audio with deeper buffering is supported or not. 0 = Not supported. 1 = Supported. Locked when HDCTL.BCLD = 1. OUTSTRMPAY--Output Stream Payload Capability (Intel(R) High Definition Audio Controller--D27:F0) Memory Address:HdBAR + 18h Default Value: 0030h Bit 15:8 7:0 17.1.2.12 Attribute: Size: RO 16 bits Description Reserved Output Stream Payload Capability (OUTSTRMPAY)--RO. Indicates maximum number of words per frame for any single output stream. This measurement is in 16 bit word quantities per 48 kHz frame. 48 Words (96B) is the maximum supported, therefore a value of 30h is reported in this register. Software must ensure that a format which would cause more words per frame than indicated is not programmed into the Output Stream Descriptor register. 00h = 0 words 01h = 1 word payload ... FFh = 255h word payload INSTRMPAY--Input Stream Payload Capability (Intel(R) High Definition Audio Controller--D27:F0) Memory Address:HdBAR + 1Ah Default Value: 0018h Bit 15:8 7:0 Datasheet R/WL 16 bits Attribute: Size: RO 16 bits Description Reserved Input Stream Payload Capability (INSTRMPAY)--RO. Indicates maximum number of words per frame for any single input stream. This measurement is in 16 bit word quantities per 48 kHz frame. 24 Words (48B) is the maximum supported, therefore a value of 18h is reported in this register. Software must ensure that a format which would cause more words per frame than indicated is not programmed into the Input Stream Descriptor register. 00h = 0 words 01h = 1 word payload ... FFh = 255h word payload 647 Integrated Intel(R) High Definition Audio (Intel(R) HD Audio) Controller Registers 17.1.2.13 INTCTL--Interrupt Control Register (Intel(R) High Definition Audio Controller--D27:F0) Memory Address:HdBAR + 20h Default Value: 00000000h R/W 32 bits Bit Description 31 Global Interrupt Enable (GIE)--R/W. Global bit to enable device interrupt generation. 1 = When set to 1, the Intel High Definition Audio function is enabled to generate an interrupt. This control is in addition to any bits in the bus specific address space, such as the Interrupt Enable bit in the PCI configuration space. Note: This bit is not affected by the D3HOT to D0 transition. 30 Controller Interrupt Enable (CIE)--R/W. Enables the general interrupt for controller functions. 1 = When set to 1, the controller generates an interrupt when the corresponding status bit gets set due to a Response Interrupt, a Response Buffer Overrun, and State Change events. Note: This bit is not affected by the D3HOT to D0 transition. 29:8 7:0 648 Attribute: Size: Reserved Stream Interrupt Enable (SIE)--R/W. When set to 1, the individual streams are enabled to generate an interrupt when the corresponding status bits get set. A stream interrupt will be caused as a result of a buffer with IOC = 1in the BDL entry being completed, or as a result of a FIFO error (underrun or overrun) occurring. Control over the generation of each of these sources is in the associated Stream Descriptor. The streams are numbered and the SIE bits assigned sequentially, based on their order in the register set. Bit 0 = input stream 1 Bit 1 = input stream 2 Bit 2 = input stream 3 Bit 3 = input stream 4 Bit 4 = output stream 1 Bit 5 = output stream 2 Bit 6 = output stream 3 Bit 7 = output stream 4 Datasheet Integrated Intel(R) High Definition Audio (Intel(R) HD Audio) Controller Registers 17.1.2.14 INTSTS--Interrupt Status Register (Intel(R) High Definition Audio Controller--D27:F0) Memory Address:HdBAR + 24h Default Value: 00000000h Attribute: Size: RO 32 bits Bit Description 31 Global Interrupt Status (GIS)--RO. This bit is an OR of all the interrupt status bits in this register. Note: This bit is not affected by the D3HOT to D0 transition. 30 Controller Interrupt Status (CIS)--RO. Status of general controller interrupt. 1 = Interrupt condition occurred due to a Response Interrupt, a Response Buffer Overrun Interrupt, or a SDIN State Change event. The exact cause can be determined by interrogating other registers. This bit is an OR of all of the stated interrupt status bits for this register. Notes: 1. This bit is set regardless of the state of the corresponding interrupt enable bit, but a hardware interrupt will not be generated unless the corresponding enable bit is set. 2. This bit is not affected by the D3HOT to D0 transition. 29:8 7:0 Reserved Stream Interrupt Status (SIS)--RO. 1 = Interrupt condition occurred on the corresponding stream. This bit is an OR of all of the stream's interrupt status bits. Note: These bits are set regardless of the state of the corresponding interrupt enable bits. The streams are numbered and the SIE bits assigned sequentially, based on their order in the register set. Bit 0 = input stream 1 Bit 1 = input stream 2 Bit 2 = input stream 3 Bit 3 = input stream 4 Bit 4 = output stream 1 Bit 5 = output stream 2 Bit 6 = output stream 3 Bit 7 = output stream 4 17.1.2.15 WALCLK--Wall Clock Counter Register (Intel(R) High Definition Audio Controller--D27:F0) Memory Address:HdBAR + 30h Default Value: 00000000h Datasheet Attribute: Size: RO 32 bits Bit Description 31:0 Wall Clock Counter--RO. A 32-bit counter that is incremented on each link Bit Clock period and rolls over from FFFF FFFFh to 0000 0000h. This counter will roll over to 0 with a period of approximately 179 seconds. This counter is enabled while the Bit Clock bit is set to 1. Software uses this counter to synchronize between multiple controllers. Will be reset on controller reset. 649 Integrated Intel(R) High Definition Audio (Intel(R) HD Audio) Controller Registers 17.1.2.16 SSYNC--Stream Synchronization Register (Intel(R) High Definition Audio Controller--D27:F0) Memory Address:HdBAR + 38h Default Value: 00000000h Bit 31:8 7:0 17.1.2.17 Attribute: Size: Description Reserved Stream Synchronization (SSYNC)--R/W. When set to 1, these bits block data from being sent on or received from the link. Each bit controls the associated stream descriptor (that is, bit 0 corresponds to the first stream descriptor, and so on) To synchronously start a set of DMA engines, these bits are first set to 1. The RUN bits for the associated stream descriptors are then set to 1 to start the DMA engines. When all streams are ready (FIFORDY =1), the associated SSYNC bits can all be set to 0 at the same time, and transmission or reception of bits to or from the link will begin together at the start of the next full link frame. To synchronously stop the streams, first these bits are set, and then the individual RUN bits in the stream descriptor are cleared by software. If synchronization is not desired, these bits may be left as 0, and the stream will simply begin running normally when the stream's RUN bit is set. The streams are numbered and the SIE bits assigned sequentially, based on their order in the register set. Bit 0 = input stream 1 Bit 1 = input stream 2 Bit 2 = input stream 3 Bit 3 = input stream 4 Bit 4 = output stream 1 Bit 5= output stream 2 Bit 6= output stream 3 Bit 7= output stream 4 CORBLBASE--CORB Lower Base Address Register (Intel(R) High Definition Audio Controller--D27:F0) Memory Address:HdBAR + 40h Default Value: 00000000h Bit 31:7 6:0 17.1.2.18 Attribute: Size: R/W, RO 32 bits Description CORB Lower Base Address--R/W. Lower address of the Command Output Ring Buffer, allowing the CORB base address to be assigned on any 128-B boundary. This register field must not be written when the DMA engine is running or the DMA transfer may be corrupted. CORB Lower Base Unimplemented Bits--RO. Hardwired to 0. This required the CORB to be allocated with 128B granularity to allow for cache line fetch optimizations. CORBUBASE--CORB Upper Base Address Register (Intel(R) High Definition Audio Controller--D27:F0) Memory Address:HdBAR + 44h Default Value: 00000000h Bit 31:0 650 R/W 32 bits Attribute: Size: R/W 32 bits Description CORB Upper Base Address--R/W. Upper 32 bits of the address of the Command Output Ring buffer. This register field must not be written when the DMA engine is running or the DMA transfer may be corrupted. Datasheet Integrated Intel(R) High Definition Audio (Intel(R) HD Audio) Controller Registers 17.1.2.19 CORBWP--CORB Write Pointer Register (Intel(R) High Definition Audio Controller--D27:F0) Memory Address:HdBAR + 48h Default Value: 0000h Bit 15:8 7:0 17.1.2.20 Attribute: Size: Description Reserved CORB Write Pointer--R/W. Software writes the last valid CORB entry offset into this field in DWord granularity. The DMA engine fetches commands from the CORB until the Read pointer matches the Write pointer. Supports 256 CORB entries (256x4B = 1KB). This register field may be written when the DMA engine is running. CORBRP--CORB Read Pointer Register (Intel(R) High Definition Audio Controller--D27:F0) Memory Address:HdBAR + 4Ah Default Value: 0000h Attribute: Size: Description 15 CORB Read Pointer Reset--R/W. Software writes a 1 to this bit to reset the CORB Read Pointer to 0 and clear any residual prefetched commands in the CORB hardware buffer within the Intel High Definition Audio controller. The hardware will physically update this bit to 1 when the CORB Pointer reset is complete. Software must read a 1 to verify that the reset completed correctly. Software must clear this bit back to 0 and read back the 0 to verify that the clear completed correctly. The CORB DMA engine must be stopped prior to resetting the Read Pointer or else DMA transfer may be corrupted. 7:0 Reserved CORB Read Pointer (CORBRP)--RO. Software reads this field to determine how many commands it can write to the CORB without over-running. The value read indicates the CORB Read Pointer offset in DWord granularity. The offset entry read from this field has been successfully fetched by the DMA controller and may be over-written by software. Supports 256 CORB entries (256 x 4B=1KB). This field may be read while the DMA engine is running. CORBCTL--CORB Control Register (Intel(R) High Definition Audio Controller--D27:F0) Memory Address:HdBAR + 4Ch Default Value: 00h Bit 7:2 Datasheet R/W, RO 16 bits Bit 14:8 17.1.2.21 R/W 16 bits Attribute: Size: R/W 8 bits Description Reserved 1 Enable CORB DMA Engine--R/W. 0 = DMA stop 1 = DMA run After software writes a 0 to this bit, the hardware may not stop immediately. The hardware will physically update the bit to 0 when the DMA engine is truly stopped. Software must read a 0 from this bit to verify that the DMA engine is truly stopped. 0 CORB Memory Error Interrupt Enable--R/W. If this bit is set, the controller will generate an interrupt if the CMEI status bit (HdBAR + 4Dh: bit 0) is set. 651 Integrated Intel(R) High Definition Audio (Intel(R) HD Audio) Controller Registers 17.1.2.22 CORBST--CORB Status Register (Intel(R) High Definition Audio Controller--D27:F0) Memory Address:HdBAR + 4Dh Default Value: 00h Bit 7:1 0 17.1.2.23 Attribute: Size: Description Reserved CORB Memory Error Indication (CMEI)--R/WC. 1 = Controller detected an error in the path way between the controller and memory. This may be an ECC bit error or any other type of detectable data error which renders the command data fetched invalid. Software can clear this bit by writing a 1 to it. However, this type of error leaves the audio subsystem in an un-viable state and typically requires a controller reset by writing a 0 to the Controller Reset # bit (HdBAR + 08h: bit 0). CORBSIZE--CORB Size Register Intel(R) High Definition Audio Controller--D27:F0) Memory Address:HdBAR + 4Eh Default Value: 42h 17.1.2.24 Attribute: Size: Description 7:4 CORB Size Capability--RO. Hardwired to 0100b indicating that the PCH only supports a CORB size of 256 CORB entries (1024B) 3:2 Reserved 1:0 CORB Size--RO. Hardwired to 10b which sets the CORB size to 256 entries (1024B) RIRBLBASE--RIRB Lower Base Address Register (Intel(R) High Definition Audio Controller--D27:F0) Bit Attribute: Size: R/W, RO 32 bits Description 31:7 RIRB Lower Base Address--R/W. Lower address of the Response Input Ring Buffer, allowing the RIRB base address to be assigned on any 128-B boundary. This register field must not be written when the DMA engine is running or the DMA transfer may be corrupted. 6:0 RIRB Lower Base Unimplemented Bits--RO. Hardwired to 0. This required the RIRB to be allocated with 128-B granularity to allow for cache line fetch optimizations. RIRBUBASE--RIRB Upper Base Address Register (Intel(R) High Definition Audio Controller--D27:F0) Memory Address:HdBAR + 54h Default Value: 00000000h 652 RO 8 bits Bit Memory Address:HdBAR + 50h Default Value: 00000000h 17.1.2.25 R/WC 8 bits Attribute: Size: R/W 32 bits Bit Description 31:0 RIRB Upper Base Address--R/W. Upper 32 bits of the address of the Response Input Ring Buffer. This register field must not be written when the DMA engine is running or the DMA transfer may be corrupted. Datasheet Integrated Intel(R) High Definition Audio (Intel(R) HD Audio) Controller Registers 17.1.2.26 RIRBWP--RIRB Write Pointer Register (Intel(R) High Definition Audio Controller--D27:F0) Memory Address:HdBAR + 58h Default Value: 0000h Description 15 RIRB Write Pointer Reset--R/W. Software writes a 1 to this bit to reset the RIRB Write Pointer to 0. The RIRB DMA engine must be stopped prior to resetting the Write Pointer or else DMA transfer may be corrupted. This bit is always read as 0. 7:0 Reserved RIRB Write Pointer (RIRBWP)--RO. Indicates the last valid RIRB entry written by the DMA controller. Software reads this field to determine how many responses it can read from the RIRB. The value read indicates the RIRB Write Pointer offset in 2 DWord RIRB entry units (since each RIRB entry is 2 DWords long). Supports up to 256 RIRB entries (256 x 8 B = 2 KB). This register field may be written when the DMA engine is running. RINTCNT--Response Interrupt Count Register (Intel(R) High Definition Audio Controller--D27:F0) Memory Address:HdBAR + 5Ah Default Value: 0000h Bit 15:8 7:0 17.1.2.28 Attribute: Size: R/W 16 bits Description Reserved N Response Interrupt Count--R/W. 0000 0001b = 1 response sent to RIRB ........... 1111 1111b = 255 responses sent to RIRB 0000 0000b = 256 responses sent to RIRB The DMA engine should be stopped when changing this field or else an interrupt may be lost. Each response occupies 2 DWords in the RIRB. This is compared to the total number of responses that have been returned, as opposed to the number of frames in which there were responses. If more than one codecs responds in one frame, then the count is increased by the number of responses received in the frame. RIRBCTL--RIRB Control Register (Intel(R) High Definition Audio Controller--D27:F0) Memory Address:HdBAR + 5Ch Default Value: 00h Bit 7:3 Datasheet R/W, RO 16 bits Bit 14:8 17.1.2.27 Attribute: Size: Attribute: Size: R/W 8 bits Description Reserved 2 Response Overrun Interrupt Control--R/W. If this bit is set, the hardware will generate an interrupt when the Response Overrun Interrupt Status bit (HdBAR + 5Dh: bit 2) is set. 1 Enable RIRB DMA Engine--R/W. 0 = DMA stop 1 = DMA run After software writes a 0 to this bit, the hardware may not stop immediately. The hardware will physically update the bit to 0 when the DMA engine is truly stopped. Software must read a 0 from this bit to verify that the DMA engine is truly stopped. 0 Response Interrupt Control--R/W. 0 = Disable Interrupt 1 = Generate an interrupt after N number of responses are sent to the RIRB buffer OR when an empty Response slot is encountered on all SDI[x] inputs (whichever occurs first). The N counter is reset when the interrupt is generated. 653 Integrated Intel(R) High Definition Audio (Intel(R) HD Audio) Controller Registers 17.1.2.29 RIRBSTS--RIRB Status Register (Intel(R) High Definition Audio Controller--D27:F0) Memory Address:HdBAR + 5Dh Default Value: 00h Bit 7:3 2 17.1.2.30 Attribute: Size: Description Reserved Response Overrun Interrupt Status--R/WC. 1 = Software sets this bit to 1 when the RIRB DMA engine is not able to write the incoming responses to memory before additional incoming responses overrun the internal FIFO. When the overrun occurs, the hardware will drop the responses which overrun the buffer. An interrupt may be generated if the Response Overrun Interrupt Control bit is set. This status bit is set even if an interrupt is not enabled for this event. Software clears this bit by writing a 1 to it. 1 Reserved 0 Response Interrupt--R/WC. 1 = Hardware sets this bit to 1 when an interrupt has been generated after N number of Responses are sent to the RIRB buffer OR when an empty Response slot is encountered on all SDI[x] inputs (whichever occurs first). This status bit is set even if an interrupt is not enabled for this event. Software clears this bit by writing a 1 to it. RIRBSIZE--RIRB Size Register (Intel(R) High Definition Audio Controller--D27:F0) Memory Address:HdBAR + 5Eh Default Value: 42h Bit 17.1.2.31 Attribute: Size: RO 8 bits Description 7:4 RIRB Size Capability--RO. Hardwired to 0100b indicating that the PCH only supports a RIRB size of 256 RIRB entries (2048B). 3:2 Reserved 1:0 RIRB Size--RO. Hardwired to 10b which sets the CORB size to 256 entries (2048B). IC--Immediate Command Register (Intel(R) High Definition Audio Controller--D27:F0) Memory Address:HdBAR + 60h Default Value: 00000000h 654 R/WC 8 bits Attribute: Size: R/W 32 bits Bit Description 31:0 Immediate Command Write--R/W. The command to be sent to the codec using the Immediate Command mechanism is written to this register. The command stored in this register is sent out over the link during the next available frame after a 1 is written to the ICB bit (HdBAR + 68h: bit 0). Datasheet Integrated Intel(R) High Definition Audio (Intel(R) HD Audio) Controller Registers 17.1.2.32 IR--Immediate Response Register (Intel(R) High Definition Audio Controller--D27:F0) Memory Address:HdBAR + 64h Default Value: 00000000h 17.1.2.33 Attribute: Size: Bit Description 31:0 Immediate Response Read (IRR)--RO. This register contains the response received from a codec resulting from a command sent using the Immediate Command mechanism. If multiple codecs responded in the same time, there is no assurance as to which response will be latched. Therefore, broadcast-type commands must not be issued using the Immediate Command mechanism. ICS--Immediate Command Status Register (Intel(R) High Definition Audio Controller--D27:F0) Memory Address:HdBAR + 68h Default Value: 0000h Bit 15:2 17.1.2.34 Attribute: Size: R/W, R/WC 16 bits Description Reserved 1 Immediate Result Valid (IRV)--R/WC. 1 = Set to 1 by hardware when a new response is latched into the Immediate Response register (HdBAR + 64). This is a status flag indicating that software may read the response from the Immediate Response register. Software must clear this bit by writing a 1 to it before issuing a new command so that the software may determine when a new response has arrived. 0 Immediate Command Busy (ICB)--R/W. When this bit is read as 0, it indicates that a new command may be issued using the Immediate Command mechanism. When this bit transitions from a 0 to a 1 (using software writing a 1), the controller issues the command currently stored in the Immediate Command register to the codec over the link. When the corresponding response is latched into the Immediate Response register, the controller hardware sets the IRV flag and clears the ICB bit back to 0. Software may write this bit to a 0 if the bit fails to return to 0 after a reasonable time out period. Note: An Immediate Command must not be issued while the CORB/RIRB mechanism is operating, otherwise the responses conflict. This must be enforced by software. DPLBASE--DMA Position Lower Base Address Register (Intel(R) High Definition Audio Controller--D27:F0) Memory Address:HdBAR + 70h Default Value: 00000000h Attribute: Size: R/W, RO 32 bits Bit Description 31:7 DMA Position Lower Base Address--R/W. Lower 32 bits of the DMA Position Buffer Base Address. This register field must not be written when any DMA engine is running or the DMA transfer may be corrupted. This same address is used by the Flush Control and must be programmed with a valid value before the Flush Control bit (HdBAR+08h:bit 1) is set. 6:1 0 Datasheet RO 32 bits DMA Position Lower Base Unimplemented bits--RO. Hardwired to 0 to force the 128-byte buffer alignment for cache line write optimizations. DMA Position Buffer Enable--R/W. 1 = Controller will write the DMA positions of each of the DMA engines to the buffer in the main memory periodically (typically once per frame). Software can use this value to know what data in memory is valid data. 655 Integrated Intel(R) High Definition Audio (Intel(R) HD Audio) Controller Registers 17.1.2.35 DPUBASE--DMA Position Upper Base Address Register (Intel(R) High Definition Audio Controller--D27:F0) Memory Address:HdBAR + 74h Default Value: 00000000h 17.1.2.36 Attribute: Size: Bit Description 31:0 DMA Position Upper Base Address--R/W. Upper 32 bits of the DMA Position Buffer Base Address. This register field must not be written when any DMA engine is running or the DMA transfer may be corrupted. SDCTL--Stream Descriptor Control Register (Intel(R) High Definition Audio Controller--D27:F0) Memory Address:Input Stream[0]: HdBAR + 80h Input Stream[1]: HdBAR + A0h Input Stream[2]: HdBAR + C0h Input Stream[3]: HdBAR + E0h Output Stream[0]: HdBAR + 100h Output Stream[1]: HdBAR + 120h Output Stream[2]: HdBAR + 140h Output Stream[3]: HdBAR + 160h Default Value: 040000h Attribute: R/W, RO Size: 24 bits Bit Description 23:20 Stream Number--R/W. This value reflect the Tag associated with the data being transferred on the link. When data controlled by this descriptor is sent out over the link, it will have its stream number encoded on the SYNC signal. When an input stream is detected on any of the SDI signals that match this value, the data samples are loaded into FIFO associated with this descriptor. While a single SDI input may contain data from more than one stream number, two different SDI inputs may not be configured with the same stream number. 0000 = Reserved 0001 = Stream 1 ........ 1110 = Stream 14 1111 = Stream 15 19 Bidirectional Direction Control--RO. This bit is only meaningful for bidirectional streams; therefore, this bit is hardwired to 0. 18 Traffic Priority--RO. Hardwired to 1 indicating that all streams will use VC1 if it is enabled through the PCI Express* registers. 17:16 Stripe Control--RO. This bit is only meaningful for input streams; therefore, this bit is hardwired to 0. 15:5 656 R/W 32 bits Reserved 4 Descriptor Error Interrupt Enable--R/W. 0 = Disable 1 = An interrupt is generated when the Descriptor Error Status bit is set. 3 FIFO Error Interrupt Enable--R/W. This bit controls whether the occurrence of a FIFO error (overrun for input or underrun for output) will cause an interrupt or not. If this bit is not set, bit 3in the Status register will be set, but the interrupt will not occur. Either way, the samples will be dropped. 2 Interrupt on Completion Enable--R/W. This bit controls whether or not an interrupt occurs when a buffer completes with the IOC bit set in its descriptor. If this bit is not set, bit 2 in the Status register will be set, but the interrupt will not occur. Datasheet Integrated Intel(R) High Definition Audio (Intel(R) HD Audio) Controller Registers 17.1.2.37 Bit Description 1 Stream Run (RUN)--R/W. 0 = DMA engine associated with this input stream will be disabled. The hardware will report a 0 in this bit when the DMA engine is actually stopped. Software must read a 0 from this bit before modifying related control registers or restarting the DMA engine. 1 = DMA engine associated with this input stream will be enabled to transfer data from the FIFO to the main memory. The SSYNC bit must also be cleared in order for the DMA engine to run. For output streams, the cadence generator is reset whenever the RUN bit is set. 0 Stream Reset (SRST)--R/W. 0 = Writing a 0 causes the corresponding stream to exit reset. When the stream hardware is ready to begin operation, it will report a 0 in this bit. Software must read a 0 from this bit before accessing any of the stream registers. 1 = Writing a 1 causes the corresponding stream to be reset. The Stream Descriptor registers (except the SRST bit itself) and FIFOs for the corresponding stream are reset. After the stream hardware has completed sequencing into the reset state, it will report a 1 in this bit. Software must read a 1 from this bit to verify that the stream is in reset. The RUN bit must be cleared before SRST is asserted. SDSTS--Stream Descriptor Status Register (Intel(R) High Definition Audio Controller--D27:F0) Memory Address:Input Stream[0]: HdBAR + 83h Input Stream[1]: HdBAR + A3h Input Stream[2]: HdBAR + C3h Input Stream[3]: HdBAR + E3h Output Stream[0]: HdBAR + 103h Output Stream[1]: HdBAR + 123h Output Stream[2]: HdBAR + 143h Output Stream[3]: HdBAR + 163h Default Value: 00h Bit 7:6 R/WC, RO Size: 8 bits Description Reserved 5 FIFO Ready (FIFORDY)--RO. For output streams, the controller hardware will set this bit to 1 while the output DMA FIFO contains enough data to maintain the stream on the link. This bit defaults to 0 on reset because the FIFO is cleared on a reset. For input streams, the controller hardware will set this bit to 1 when a valid descriptor is loaded and the engine is ready for the RUN bit to be set. 4 Descriptor Error--R/WC. 1 = A serious error occurred during the fetch of a descriptor. This could be a result of a Master Abort, a parity or ECC error on the bus, or any other error which renders the current Buffer Descriptor or Buffer Descriptor list useless. This error is treated as a fatal stream error, as the stream cannot continue running. The RUN bit will be cleared and the stream will stopped. Software may attempt to restart the stream engine after addressing the cause of the error and writing a 1 to this bit to clear it. 3 FIFO Error--R/WC. 1 = FIFO error occurred. This bit is set even if an interrupt is not enabled. The bit is cleared by writing a 1 to it. For an input stream, this indicates a FIFO overrun occurring while the RUN bit is set. When this happens, the FIFO pointers do not increment and the incoming data is not written into the FIFO, thereby being lost. For an output stream, this indicates a FIFO underrun when there are still buffers to send. The hardware should not transmit anything on the link for the associated stream if there is not valid data to send. 2 Buffer Completion Interrupt Status--R/WC. This bit is set to 1 by the hardware after the last sample of a buffer has been processed, AND if the Interrupt on Completion bit is set in the command byte of the buffer descriptor. It remains active until software clears it by writing a 1 to it. 1:0 Datasheet Attribute: Reserved 657 Integrated Intel(R) High Definition Audio (Intel(R) HD Audio) Controller Registers 17.1.2.38 SDLPIB--Stream Descriptor Link Position in Buffer Register (Intel(R) High Definition Audio Controller--D27:F0) Memory Address:Input Stream[0]: HdBAR + 84h Input Stream[1]: HdBAR + A4h Input Stream[2]: HdBAR + C4h Input Stream[3]: HdBAR + E4h Output Stream[0]: HdBAR + 104h Output Stream[1]: HdBAR + 124h Output Stream[2]: HdBAR + 144h Output Stream[3]: HdBAR + 164h Default Value: 00000000h Bit 31:0 17.1.2.39 RO Size: 32 bits Description Link Position in Buffer--RO. Indicates the number of bytes that have been received off the link. This register will count from 0 to the value in the Cyclic Buffer Length register and then wrap to 0. SDCBL--Stream Descriptor Cyclic Buffer Length Register (Intel(R) High Definition Audio Controller--D27:F0) Memory Address:Input Stream[0]: HdBAR + 88h Input Stream[1]: HdBAR + A8h Input Stream[2]: HdBAR + C8h Input Stream[3]: HdBAR + E8h Output Stream[0]: HdBAR + 108h Output Stream[1]: HdBAR + 128h Output Stream[2]: HdBAR + 148h Output Stream[3]: HdBAR + 168h Default Value: 00000000h 658 Attribute: Attribute: R/W Size: 32 bits Bit Description 31:0 Cyclic Buffer Length--R/W. Indicates the number of bytes in the complete cyclic buffer. This register represents an integer number of samples. Link Position in Buffer will be reset when it reaches this value. Software may only write to this register after Global Reset, Controller Reset, or Stream Reset has occurred. This value should be only modified when the RUN bit is 0. Once the RUN bit has been set to enable the engine, software must not write to this register until after the next reset is asserted, or transfer may be corrupted. Datasheet Integrated Intel(R) High Definition Audio (Intel(R) HD Audio) Controller Registers 17.1.2.40 SDLVI--Stream Descriptor Last Valid Index Register (Intel(R) High Definition Audio Controller--D27:F0) Memory Address:Input Stream[0]: HdBAR + 8Ch Input Stream[1]: HdBAR + ACh Input Stream[2]: HdBAR + CCh Input Stream[3]: HdBAR + ECh Output Stream[0]: HdBAR + 10Ch Output Stream[1]: HdBAR + 12Ch Output Stream[2]: HdBAR + 14Ch Output Stream[3]: HdBAR + 16Ch Default Value: 0000h Bit 15:8 7:0 17.1.2.41 R/W Size: 16 bits Description Reserved Last Valid Index--R/W. The value written to this register indicates the index for the last valid Buffer Descriptor in BDL. After the controller has processed this descriptor, it will wrap back to the first descriptor in the list and continue processing. This field must be at least 1; that is, there must be at least 2 valid entries in the buffer descriptor list before DMA operations can begin. This value should only modified when the RUN bit is 0. SDFIFOW--Stream Descriptor FIFO Watermark Register (Intel(R) High Definition Audio Controller--D27:F0) Memory Address:Input Stream[0]: HdBAR + 8Eh Input Stream[1]: HdBAR + AEh Input Stream[2]: HdBAR + CEh Input Stream[3]: HdBAR + EEh Output Stream[0]: HdBAR + 10Eh Output Stream[1]: HdBAR + 12Eh Output Stream[2]: HdBAR + 14Eh Output Stream[3]: HdBAR + 16Eh Default Value: 0004h Bit 15:3 2:0 Datasheet Attribute: Attribute: RO Size: 16 bits Description Reserved FIFO Watermark (FIFOW)--RO. Indicates the minimum number of bytes accumulated/free in the FIFO before the controller will start a fetch/eviction of data. The HD Audio Controller hardwires the FIFO Watermark to either 32 B or 64 B based on the number of bytes per frame for the configured input stream. 100 = 32 B (Default) 101 = 64 B Others = Unsupported Note: When the bit field is programmed to an unsupported size, the hardware sets itself to the default value. Software must read the bit field to test if the value is supported after setting the bit field. 659 Integrated Intel(R) High Definition Audio (Intel(R) HD Audio) Controller Registers 17.1.2.42 ISDFIFOS--Input Stream Descriptor FIFO Size Register (Intel(R) High Definition Audio Controller--D27:F0) Memory Address:Input Stream[0]: HdBAR + 90h Input Stream[1]: HdBAR + B0h Input Stream[2]: HdBAR + D0h Input Stream[3]: HdBAR + F0h Output Stream[0]: HdBAR + 110h Output Stream[1]: HdBAR + 130h Output Stream[2]: HdBAR + 150h Output Stream[3]: HdBAR + 170h Default Value: 0000h 17.1.2.43 RO Size: 16 bits Bit Description 15:0 FIFO Size--RW. When GCAP2.EEACS = 0, indicates the maximum number of bytes that could be evicted (for input) or fetched (for output) by the controller at one time. This is the maximum number of bytes that may have been received into the HW buffer but not yet transferred out, and is also the maximum possible value that the PICB count will increase by at one time. The FIFO size is calculated based on factors including the stream format programmed in SDFMT register. As the default value is zero, SW must write to the respective SDFMT register to kick of the FIFO size calculation, and read back to find out the HW allocated FIFO size. As the default value is zero, SW must write to the <I/O>SD<0:3>FMT register to kick off the FIFO size calculation, and read back to find out the HW allocated FIFO size. When GCAP2.EEACS = 1, this FIFOS value represent the minimum FIFO size HW required to operate efficiently. Software can program FIFOL register to extend the effective FIFO size in HW beyond this minimum value advertised. In this case, the maximum number. SDFMT--Stream Descriptor Format Register (Intel(R) High Definition Audio Controller--D27:F0) Memory Address:Input Stream[0]: HdBAR + 92h Input Stream[1]: HdBAR + B2h Input Stream[2]: HdBAR + D2h Input Stream[3]: HdBAR + F2h Output Stream[0]: HdBAR + 112h Output Stream[1]: HdBAR + 132h Output Stream[2]: HdBAR + 152h Output Stream[3]: HdBAR + 172h Default Value: 0000h Bit Reserved 14 Sample Base Rate--R/W 0 = 48 kHz 1 = 44.1 kHz 10:8 7 Attribute: R/W Size: 16 bits Description 15 13:11 660 Attribute: Sample Base Rate Multiple--R/W 000 = 48 kHz, 44.1 kHz or less 001 = x2 (96 kHz, 88.2 kHz, 32 kHz) 010 = x3 (144 kHz) 011 = x4 (192 kHz, 176.4 kHz) Others = Reserved. Sample Base Rate Devisor--R/W. 000 = Divide by 1(48 kHz, 44.1 kHz) 001 = Divide by 2 (24 kHz, 22.05 kHz) 010 = Divide by 3 (16 kHz, 32 kHz) 011 = Divide by 4 (11.025 kHz) 100 = Divide by 5 (9.6 kHz) 101 = Divide by 6 (8 kHz) 110 = Divide by 7 111 = Divide by 8 (6 kHz) Reserved Datasheet Integrated Intel(R) High Definition Audio (Intel(R) HD Audio) Controller Registers Bit 17.1.2.44 Description 6:4 Bits per Sample (BITS)--R/W. 000 =8 bits. The data will be packed in memory in 8-bit containers on 16-bit boundaries 001 =16 bits. The data will be packed in memory in 16-bit containers on 16-bit boundaries 010 = 20 bits. The data will be packed in memory in 32-bit containers on 32-bit boundaries 011 =24 bits. The data will be packed in memory in 32-bit containers on 32-bit boundaries 100 =32 bits. The data will be packed in memory in 32-bit containers on 32-bit boundaries Others = Reserved. 3:0 Number of Channels (CHAN)--R/W. Indicates number of channels in each frame of the stream. 0000 =1 0001 =2 ........ 1111 =16 SdBDPL--Stream Descriptor Buffer Descriptor List Pointer Lower Base Address Register (Intel(R) High Definition Audio Controller--D27:F0) Memory Address:Input Stream[0]: HdBAR + 98h Input Stream[1]: HdBAR + B8h Input Stream[2]: HdBAR + D8h Input Stream[3]: HdBAR + F8h Output Stream[0]: HdBAR + 118h Output Stream[1]: HdBAR + 138h Output Stream[2]: HdBAR + 158h Output Stream[3]: HdBAR + 178h Default Value: 00000000h Bit 31:7 6:0 17.1.2.45 Attribute: R/W,RO Size: 32 bits Description Buffer Descriptor List Pointer Lower Base Address--R/W. Lower address of the Buffer Descriptor List. This value should only be modified when the RUN bit is 0, or DMA transfer may be corrupted. Hardwired to 0 forcing alignment on 128-B boundaries. SdBDPU--Stream Descriptor Buffer Descriptor List Pointer Upper Base Address Register (Intel(R) High Definition Audio Controller--D27:F0) Memory Address:Input Stream[0]: HdBAR + 9Ch Input Stream[1]: HdBAR + BCh Input Stream[2]: HdBAR + DCh Input Stream[3]: HdBAR + FCh Output Stream[0]: HdBAR + 11Ch Output Stream[1]: HdBAR + 13Ch Output Stream[2]: HdBAR + 15Ch Output Stream[3]: HdBAR + 17Ch Default Value: 00000000h bits Bit 31:0 Attribute: R/W Size: 32 Description Buffer Descriptor List Pointer Upper Base Address--R/W. Upper 32-bit address of the Buffer Descriptor List. This value should only be modified when the RUN bit is 0, or DMA transfer may be corrupted. Datasheet 661 SMBus Controller Registers (D31:F3) 18 SMBus Controller Registers (D31:F3) 18.1 PCI Configuration Registers (SMBus--D31:F3) Table 18-1. SMBus Controller PCI Register Address Map (SMBus--D31:F3) Offset Default Attribute VID Vendor Identification 8086 RO 02h-03h DID Device Identification See register description RO 04h-05h PCICMD PCI Command 0000h R/W, RO 06h-07h PCISTS PCI Status 0280h RO 08h RID Revision Identification See register description RO 09h PI Programming Interface 00h RO 0Ah SCC Sub Class Code 05h RO 0Bh BCC Base Class Code 0Ch RO 10h SMBMBAR0 Memory Base Address Register 0 (Bit 31:0) 00000004h R/W, RO 14h SMBMBAR1 Memory Based Address Register 1 (Bit 63:32) 00000000h R/W 20h-23h SMB_BASE SMBus Base Address 2Ch-2Dh SVID 00000001h R/W, RO Subsystem Vendor Identification 0000h RO Subsystem Identification 2Eh-2Fh SID 0000h R/WO 3Ch INT_LN Interrupt Line 00h R/W 3Dh INT_PN Interrupt Pin See register description RO 40h HOSTC Host Configuration 00h R/W, R/WO Registers that are not shown should be treated as Reserved (See Section 9.2 for details). VID--Vendor Identification Register (SMBus--D31:F3) Address: Default Value: Bit 15:0 662 Register Name 00h-01h Note: 18.1.1 Mnemonic 00h-01h 8086h Attribute: Size: RO 16 bits Description Vendor ID--RO. This is a 16-bit value assigned to Intel Datasheet SMBus Controller Registers (D31:F3) 18.1.2 DID--Device Identification Register (SMBus--D31:F3) Address: Default Value: 18.1.3 02h-03h See bit description RO 16 bits Bit Description 15:0 Device ID--RO. This is a 16-bit value assigned to the PCH SMBus controller. See Section 1.3 for the value of the DID Register. PCICMD--PCI Command Register (SMBus--D31:F3) Address: Default Value: 04h-05h 0000h Bit 15:11 10 Datasheet Attribute: Size: Attribute: Size: RO, R/W 16 bits Description Reserved Interrupt Disable--R/W. 0 = Enable 1 = Disables SMBus to assert its PIRQB# signal. 9 Fast Back to Back Enable (FBE)--RO. Hardwired to 0. 8 SERR# Enable (SERR_EN)--R/W. 0 = Enables SERR# generation. 1 = Disables SERR# generation. 7 Wait Cycle Control (WCC)--RO. Hardwired to 0. 6 Parity Error Response (PER)--R/W. 0 = Disable 1 = Sets Detected Parity Error bit (D31:F3:06, bit 15) when a parity error is detected. 5 VGA Palette Snoop (VPS)--RO. Hardwired to 0. 4 Postable Memory Write Enable (PMWE)--RO. Hardwired to 0. 3 Special Cycle Enable (SCE)--RO. Hardwired to 0. 2 Bus Master Enable (BME)--RO. Hardwired to 0. 1 Memory Space Enable (MSE)--R/W. 0 = Disables memory mapped config space. 1 = Enables memory mapped config space. 0 I/O Space Enable (IOSE)--R/W. 0 = Disable 1 = Enables access to the SMBus I/O space registers as defined by the Base Address Register. 663 SMBus Controller Registers (D31:F3) 18.1.4 PCISTS--PCI Status Register (SMBus--D31:F3) Address: Default Value: Note: 06h-07h 0280h Description 15 Detected Parity Error (DPE)--R/WC. 0 = No parity error detected. 1 = Parity error detected. 14 Signaled System Error (SSE)--R/WC. 0 = No system error detected. 1 = System error detected. 13 Received Master Abort (RMA)--RO. Hardwired to 0. 12 Received Target Abort (RTA)--RO. Hardwired to 0. 11 10:9 Signaled Target Abort (STA)--RO. Hardwired to 0. DEVSEL# Timing Status (DEVT)--RO. This 2-bit field defines the timing for DEVSEL# assertion for positive decode. 01 = Medium timing. 8 Data Parity Error Detected (DPED)--RO. Hardwired to 0. 7 Fast Back to Back Capable (FB2BC)--RO. Hardwired to 1. 6 User Definable Features (UDF)--RO. Hardwired to 0. 5 66 MHz Capable (66MHZ_CAP)--RO. Hardwired to 0. 4 Capabilities List (CAP_LIST)--RO. Hardwired to 0 because there are no capability list structures in this function 3 Interrupt Status (INTS)--RO. This bit indicates that an interrupt is pending. It is independent from the state of the Interrupt Enable bit in the PCI Command register. 2:0 Reserved RID--Revision Identification Register (SMBus--D31:F3) Offset Address: 08h Default Value: See bit description Bit 7:0 18.1.6 Attribute: Size: RO 8 bits Description Revision ID--RO. This field indicates the device specific revision identifier. See Section 1.3 the value of the RID Register. PI--Programming Interface Register (SMBus--D31:F3) Offset Address: 09h Default Value: 00h Bit 7:0 664 RO 16 bits For the writable bits, software must write a 1 to clear bits that are set. Writing a 0 to the bit has no effect. Bit 18.1.5 Attribute: Size: Attribute: Size: RO 8 bits Description Reserved Datasheet SMBus Controller Registers (D31:F3) 18.1.7 SCC--Sub Class Code Register (SMBus--D31:F3) Address Offset: 0Ah Default Value: 05h Bit 7:0 18.1.8 Attribute: Size: Description Sub Class Code (SCC)--RO. 05h = SMBus serial controller BCC--Base Class Code Register (SMBus--D31:F3) Address Offset: 0Bh Default Value: 0Ch Bit 7:0 18.1.9 Attribute: Size: Base Class Code (BCC)--RO. 0Ch = Serial controller. SMBMBAR0--D31_F3_SMBus Memory Base Address 0 Register (SMBus--D31:F3) Bit 31:8 7:4 3 2:1 0 Attribute: Size: R/W, RO 32 bits Description Base Address--R/W. Provides the 32 byte system memory base address for the PCH SMB logic. Reserved Prefetchable (PREF)--RO. Hardwired to 0. Indicates that SMBMBAR is not prefetchable. Address Range (ADDRNG)--RO. Indicates that this SMBMBAR can be located anywhere in 64-bit address space. Hardwired to 10b. Memory Space Indicator--RO. This read-only bit always is 0, indicating that the SMB logic is Memory mapped. SMBMBAR1--D31_F3_SMBus Memory Base Address 1 Register (SMBus--D31:F3) Address Offset: 14h-17h Default Value: 00000000h Bit 31:0 Datasheet RO 8 bits Description Address Offset: 10-13h Default Value: 00000004h 18.1.10 RO 8 bits Attribute: Size: R/W 32 bits Description Base Address--R/W. Provides bits 63:32 system memory base address for the PCH SMB logic. 665 SMBus Controller Registers (D31:F3) 18.1.11 SMB_BASE--SMBus Base Address Register (SMBus--D31:F3) Address Offset: 20-23h Default Value: 00000001h Bit 31:16 15:5 4:1 0 18.1.12 Attribute: Size: Description Reserved--RO Base Address--R/W. This field provides the 32-byte system I/O base address for the PCH's SMB logic. Reserved--RO IO Space Indicator--RO. Hardwired to 1 indicating that the SMB logic is I/O mapped. SVID--Subsystem Vendor Identification Register (SMBus--D31:F2/F4) Address Offset: 2Ch-2Dh Default Value: 0000h Lockable: No 18.1.13 Attribute: RO Size: 16 bits Power Well:Core Bit Description 15:0 Subsystem Vendor ID (SVID)--RO. The SVID register, in combination with the Subsystem ID (SID) register, enables the operating system (OS) to distinguish subsystems from each other. The value returned by reads to this register is the same as that which was written by BIOS into the IDE SVID register. Note: Software can write to this register only once per core well reset. Writes should be done as a single 16-bit cycle. SID--Subsystem Identification Register (SMBus--D31:F2/F4) Address Offset: 2Eh-2Fh Default Value: 0000h Lockable: No Attribute: R/WO Size: 16 bits Power Well:Core Bit Description 15:0 Subsystem ID (SID)--R/WO. The SID register, in combination with the SVID register, enables the operating system (OS) to distinguish subsystems from each other. The value returned by reads to this register is the same as that which was written by BIOS into the IDE SID register. Note: 18.1.14 Software can write to this register only once per core well reset. Writes should be done as a single 16-bit cycle. INT_LN--Interrupt Line Register (SMBus--D31:F3) Address Offset: 3Ch Default Value: 00h 666 R/W, RO 32-bits Attribute: Size: R/W 8 bits Bit Description 7:0 Interrupt Line (INT_LN)--R/W. This data is not used by the PCH. It is to communicate to software the interrupt line that the interrupt pin is connected to PIRQB#. Datasheet SMBus Controller Registers (D31:F3) 18.1.15 INT_PN--Interrupt Pin Register (SMBus--D31:F3) Address Offset: 3Dh Default Value: See description Bit 7:0 18.1.16 Attribute: Size: Description Interrupt PIN (INT_PN)--RO. This reflects the value of D31IP.SMIP in chipset configuration space. HOSTC--Host Configuration Register (SMBus--D31:F3) Address Offset: 40h Default Value: 00h Bit 7:5 Datasheet RO 8 bits Attribute: Size: R/W, R/WO 8 bits Description Reserved 4 SPD Write Disable--R/WO. 0 = SPD write enabled. 1 = SPD write disabled. Writes to SMBus addresses 50h - 57h are disabled. Note: This bit is R/WO and will be reset on PLTRST# assertion. This bit should be set by BIOS to `1'. SW can only program this bit when both the START bit (SMB_BASE + 02h, bit 6) and Host Busy bit (SMB_BASE + 00h, bit 0) are `0'; otherwise the write may result in undefined behavior. 3 Soft SMBus Reset (SSRESET)--R/W. 0 = The HW will reset this bit to 0 when SMBus reset operation is completed. 1 = The SMBus state machine and logic in the PCH is reset. 2 I2C_EN--R/W. 0 = SMBus behavior. 1 = The PCH is enabled to communicate with I2C devices. This will change the formatting of some commands. 1 SMB_SMI_EN--R/W. 0 = SMBus interrupts will not generate an SMI#. 1 = Any source of an SMB interrupt will instead be routed to generate an SMI#. Refer to Section 5.22.4 (Interrupts / SMI#). This bit needs to be set for SMBALERT# to be enabled. 0 SMBus Host Enable (HST_EN)--R/W. 0 = Disable the SMBus Host controller. 1 = Enable. The SMB Host controller interface is enabled to execute commands. The INTREN bit (offset SMB_BASE + 02h, bit 0) needs to be enabled for the SMB Host controller to interrupt or SMI#. The SMB Host controller will not respond to any new requests until all interrupt requests have been cleared. 667 SMBus Controller Registers (D31:F3) 18.2 SMBus I/O and Memory Mapped I/O Registers The SMBus registers (see Table 18-1) can be accessed through I/O BAR or Memory BAR registers in PCI configuration space. The offsets are the same for both I/O and Memory Mapped I/O registers. Table 18-1. SMBus I/O and Memory Mapped I/O Register Address Map SMB_BASE + Offset 668 Mnemonic Register Name Default Attribute 00h HST_STS Host Status 00h R/WC, RO 02h HST_CNT Host Control 00h R/W, WO 03h HST_CMD Host Command 00h R/W 04h XMIT_SLVA Transmit Slave Address 00h R/W 05h HST_D0 Host Data 0 00h R/W 06h HST_D1 Host Data 1 00h R/W 07h HOST_BLOCK_dB 08h PEC Host Block Data Byte 00h R/W Packet Error Check 00h R/W 09h RCV_SLVA Receive Slave Address 0Ah-0Bh SLV_DATA Receive Slave Data 44h R/W 0000h RO 0Ch AUX_STS Auxiliary Status 00h R/WC, RO 0Dh AUX_CTL Auxiliary Control 00h R/W 0Eh SMLINK_PIN_CTL SMLink Pin Control (TCO Compatible Mode) See register description R/W, RO 0Fh SMBus_PIN_CTL SMBus Pin Control See register description R/W, RO 10h SLV_STS Slave Status 00h R/WC 11h SLV_CMD Slave Command 00h R/W 14h NOTIFY_DADDR Notify Device Address 00h RO 16h NOTIFY_DLOW Notify Data Low Byte 00h RO 17h NOTIFY_DHIGH Notify Data High Byte 00h RO Datasheet SMBus Controller Registers (D31:F3) 18.2.1 HST_STS--Host Status Register (SMBus--D31:F3) Register Offset: SMB_BASE + 00h Default Value: 00h Attribute: Size: R/WC, RO 8-bits All status bits are set by hardware and cleared by the software writing a one to the particular bit position. Writing a 0 to any bit position has no effect. Bit Description 7 Byte Done Status (DS)--R/WC. 0 = Software can clear this by writing a 1 to it. 1 = Host controller received a byte (for Block Read commands) or if it has completed transmission of a byte (for Block Write commands) when the 32-byte buffer is not being used. This bit will be set, even on the last byte of the transfer. This bit is not set when transmission is due to the LAN interface heartbeat. This bit has no meaning for block transfers when the 32-byte buffer is enabled. Note: Datasheet When the last byte of a block message is received, the host controller will set this bit. However, it will not immediately set the INTR bit (bit 1 in this register). When the interrupt handler clears the DS bit, the message is considered complete, and the host controller will then set the INTR bit (and generate another interrupt). Thus, for a block message of n bytes, the PCH will generate n+1 interrupts. The interrupt handler needs to be implemented to handle these cases. When not using the 32 Byte Buffer, hardware will drive the SMBCLK signal low when the DS bit is set until SW clears the bit. This includes the last byte of a transfer. Software must clear the DS bit before it can clear the BUSY bit. 6 INUSE_STS--R/W. This bit is used as semaphore among various independent software threads that may need to use the PCH's SMBus logic, and has no other effect on hardware. 0 = After a full PCI reset, a read to this bit returns a 0. 1 = After the first read, subsequent reads will return a 1. A write of a 1 to this bit will reset the next read value to 0. Writing a 0 to this bit has no effect. Software can poll this bit until it reads a 0, and will then own the usage of the host controller. 5 SMBALERT_STS--R/WC. 0 = Interrupt or SMI# was not generated by SMBALERT#. Software clears this bit by writing a 1 to it. 1 = The source of the interrupt or SMI# was the SMBALERT# signal. This bit is only cleared by software writing a 1 to the bit position or by RSMRST# going low. If the signal is programmed as a GPIO, then this bit will never be set. 4 FAILED--R/WC. 0 = Software clears this bit by writing a 1 to it. 1 = The source of the interrupt or SMI# was a failed bus transaction. This bit is set in response to the KILL bit being set to terminate the host transaction. 3 BUS_ERR--R/WC. 0 = Software clears this bit by writing a 1 to it. 1 = The source of the interrupt of SMI# was a transaction collision. 2 DEV_ERR--R/WC. 0 = Software clears this bit by writing a 1 to it. The PCH will then de-assert the interrupt or SMI#. 1 = The source of the interrupt or SMI# was due to one of the following: *Invalid Command Field, *Unclaimed Cycle (host initiated), *Host Device Time-out Error. 1 INTR--R/WC. This bit can only be set by termination of a command. INTR is not dependent on the INTREN bit (offset SMB_BASE + 02h, bit 0) of the Host controller register (offset 02h). It is only dependent on the termination of the command. If the INTREN bit is not set, then the INTR bit will be set, although the interrupt will not be generated. Software can poll the INTR bit in this non-interrupt case. 0 = Software clears this bit by writing a 1 to it. The PCH then de-asserts the interrupt or SMI#. 1 = The source of the interrupt or SMI# was the successful completion of its last command. 0 HOST_BUSY--R/WC. 0 = Cleared by the PCH when the current transaction is completed. 1 = Indicates that the PCH is running a command from the host interface. No SMB registers should be accessed while this bit is set, except the BLOCK DATA BYTE Register. The BLOCK DATA BYTE Register can be accessed when this bit is set only when the SMB_CMD bits in the Host Control Register are programmed for Block command or I2C Read command. This is necessary in order to check the DONE_STS bit. 669 SMBus Controller Registers (D31:F3) 18.2.2 HST_CNT--Host Control Register (SMBus--D31:F3) Register Offset: SMB_BASE + 02h Default Value: 00h Note: Attribute: Size: R/W, WO 8-bits A read to this register will clear the byte pointer of the 32-byte buffer. Bit 7 Description PEC_EN--R/W. 0 = SMBus host controller does not perform the transaction with the PEC phase appended. 1 = Causes the host controller to perform the SMBus transaction with the Packet Error Checking phase appended. For writes, the value of the PEC byte is transferred from the PEC Register. For reads, the PEC byte is loaded in to the PEC Register. This bit must be written prior to the write in which the START bit is set. 6 START--WO. 0 = This bit will always return 0 on reads. The HOST_BUSY bit in the Host Status register (offset 00h) can be used to identify when the PCH has finished the command. 1 = Writing a 1 to this bit initiates the command described in the SMB_CMD field. All registers should be setup prior to writing a 1 to this bit position. 5 LAST_BYTE--WO. This bit is used for Block Read commands. 1 = Software sets this bit to indicate that the next byte will be the last byte to be received for the block. This causes the PCH to send a NACK (instead of an ACK) after receiving the last byte. Note: 4:2 670 Once the SECOND_TO_STS bit in TCO2_STS register (D31:F0, TCOBASE+6h, bit 1) is set, the LAST_BYTE bit also gets set. While the SECOND_TO_STS bit is set, the LAST_BYTE bit cannot be cleared. This prevents the PCH from running some of the SMBus commands (Block Read/Write, I2C Read, Block I2C Write). SMB_CMD--R/W. The bit encoding below indicates which command the PCH is to perform. If enabled, the PCH will generate an interrupt or SMI# when the command has completed If the value is for a non-supported or reserved command, the PCH will set the device error (DEV_ERR) status bit (offset SMB_BASE + 00h, bit 2) and generate an interrupt when the START bit is set. The PCH will perform no command, and will not operate until DEV_ERR is cleared. 000 = Quick: The slave address and read/write value (bit 0) are stored in the transmit slave address register. 001 = Byte: This command uses the transmit slave address and command registers. Bit 0 of the slave address register determines if this is a read or write command. 010 = Byte Data: This command uses the transmit slave address, command, and DATA0 registers. Bit 0 of the slave address register determines if this is a read or write command. If it is a read, the DATA0 register will contain the read data. 011 = Word Data: This command uses the transmit slave address, command, DATA0 and DATA1 registers. Bit 0 of the slave address register determines if this is a read or write command. If it is a read, after the command completes, the DATA0 and DATA1 registers will contain the read data. 100 = Process Call: This command uses the transmit slave address, command, DATA0 and DATA1 registers. Bit 0 of the slave address register determines if this is a read or write command. After the command completes, the DATA0 and DATA1 registers will contain the read data. 101 = Block: This command uses the transmit slave address, command, DATA0 registers, and the Block Data Byte register. For block write, the count is stored in the DATA0 register and indicates how many bytes of data will be transferred. For block reads, the count is received and stored in the DATA0 register. Bit 0 of the slave address register selects if this is a read or write command. For writes, data is retrieved from the first n (where n is equal to the specified count) addresses of the SRAM array. For reads, the data is stored in the Block Data Byte register. 110 = I2C Read: This command uses the transmit slave address, command, DATA0, DATA1 registers, and the Block Data Byte register. The read data is stored in the Block Data Byte register. The PCH continues reading data until the NAK is received. 111 = Block Process: This command uses the transmit slave address, command, DATA0 and the Block Data Byte register. For block write, the count is stored in the DATA0 register and indicates how many bytes of data will be transferred. For block read, the count is received and stored in the DATA0 register. Bit 0 of the slave address register always indicate a write command. For writes, data is retrieved from the first m (where m is equal to the specified count) addresses of the SRAM array. For reads, the data is stored in the Block Data Byte register. Note: E32B bit in the Auxiliary Control register must be set for this command to work. Datasheet SMBus Controller Registers (D31:F3) Bit 18.2.3 Description 1 KILL--R/W. 0 = Normal SMBus host controller functionality. 1 = Kills the current host transaction taking place, sets the FAILED status bit, and asserts the interrupt (or SMI#). This bit, once set, must be cleared by software to allow the SMBus host controller to function normally. 0 INTREN--R/W. 0 = Disable. 1 = Enable the generation of an interrupt or SMI# upon the completion of the command. HST_CMD--Host Command Register (SMBus--D31:F3) Register Offset: SMB_BASE + 03h Default Value: 00h Bit 7:0 18.2.4 Attribute: Size: R/W 8 bits Description This 8-bit field is transmitted by the host controller in the command field of the SMBus protocol during the execution of any command. XMIT_SLVA--Transmit Slave Address Register (SMBus--D31:F3) Register Offset: SMB_BASE + 04h Default Value: 00h Attribute: Size: R/W 8 bits This register is transmitted by the host controller in the slave address field of the SMBus protocol. Bit 7:1 0 18.2.5 Description Address--R/W. This field provides a 7-bit address of the targeted slave. RW--R/W. Direction of the host transfer. 0 = Write 1 = Read Note: Writes to SMBus addresses 50h - 57h are disabled depending on the setting of bit 4 in HOSTC register (D31:F3:Offset 40h). HST_D0--Host Data 0 Register (SMBus--D31:F3) Register Offset: SMB_BASE + 05h Default Value: 00h Datasheet Attribute: Size: R/W 8 bits Bit Description 7:0 Data0/Count--R/W. This field contains the 8-bit data sent in the DATA0 field of the SMBus protocol. For block write commands, this register reflects the number of bytes to transfer. This register should be programmed to a value between 1 and 32 for block counts. A count of 0 or a count above 32 will result in unpredictable behavior. The host controller does not check or log invalid block counts. 671 SMBus Controller Registers (D31:F3) 18.2.6 HST_D1--Host Data 1 Register (SMBus--D31:F3) Register Offset: SMB_BASE + 06h Default Value: 00h Bit 7:0 18.2.7 Attribute: Size: Description Data1--R/W. This 8-bit register is transmitted in the DATA1 field of the SMBus protocol during the execution of any command. Host_BLOCK_dB--Host Block Data Byte Register (SMBus--D31:F3) Register Offset: SMB_BASE + 07h Default Value: 00h 18.2.8 Attribute: Size: R/W 8 bits Bit Description 7:0 Block Data (BDTA)--R/W. This is either a register, or a pointer into a 32-byte block array, depending upon whether the E32B bit is set in the Auxiliary Control register. When the E32B bit (offset SMB_BASE + 0Dh, bit 1) is cleared, this is a register containing a byte of data to be sent on a block write or read from on a block read. When the E32B bit is set, reads and writes to this register are used to access the 32-byte block data storage array. An internal index pointer is used to address the array, which is reset to 0 by reading the HCTL register (offset 02h). The index pointer then increments automatically upon each access to this register. The transfer of block data into (read) or out of (write) this storage array during an SMBus transaction always starts at index address 0. When the E2B bit is set, for writes, software will write up to 32-bytes to this register as part of the setup for the command. After the Host controller has sent the Address, Command, and Byte Count fields, it will send the bytes in the SRAM pointed to by this register. When the E2B bit is cleared for writes, software will place a single byte in this register. After the host controller has sent the address, command, and byte count fields, it will send the byte in this register. If there is more data to send, software will write the next series of bytes to the SRAM pointed to by this register and clear the DONE_STS bit. The controller will then send the next byte. During the time between the last byte being transmitted to the next byte being transmitted, the controller will insert wait-states on the interface. When the E2B bit is set for reads, after receiving the byte count into the Data0 register, the first series of data bytes go into the SRAM pointed to by this register. If the byte count has been exhausted or the 32-byte SRAM has been filled, the controller will generate an SMI# or interrupt (depending on configuration) and set the DONE_STS bit. Software will then read the data. During the time between when the last byte is read from the SRAM to when the DONE_STS bit is cleared, the controller will insert wait-states on the interface. PEC--Packet Error Check (PEC) Register (SMBus--D31:F3) Register Offset: SMB_BASE + 08h Default Value: 00h 672 R/W 8 bits Attribute: Size: R/W 8 bits Bit Description 7:0 PEC_DATA--R/W. This 8-bit register is written with the 8-bit CRC value that is used as the SMBus PEC data prior to a write transaction. For read transactions, the PEC data is loaded from the SMBus into this register and is then read by software. Software must ensure that the INUSE_STS bit is properly maintained to avoid having this field over-written by a write transaction following a read transaction. Datasheet SMBus Controller Registers (D31:F3) 18.2.9 RCV_SLVA--Receive Slave Address Register (SMBus--D31:F3) Register Offset: SMB_BASE + 09h Default Value: 44h Lockable: No Bit 7 6:0 18.2.10 Attribute: R/W Size: 8 bits Power Well:Resume Description Reserved SLAVE_ADDR--R/W. This field is the slave address that the PCH decodes for read and write cycles. the default is not 0, so the SMBus Slave Interface can respond even before the processor comes up (or if the processor is dead). This register is cleared by RSMRST#, but not by PLTRST#. SLV_DATA--Receive Slave Data Register (SMBus--D31:F3) Register Offset: SMB_BASE + 0Ah-0Bh Default Value: 0000h Lockable: No Attribute: RO Size: 16 bits Power Well:Resume This register contains the 16-bit data value written by the external SMBus master. The processor can then read the value from this register. This register is reset by RSMRST#, but not PLTRST#. Bit 15:8 7:0 18.2.11 Description Data Message Byte 1 (DATA_MSG1)--RO. See Section 5.22.7 for a discussion of this field. Data Message Byte 0 (DATA_MSG0)--RO. See Section 5.22.7 for a discussion of this field. AUX_STS--Auxiliary Status Register (SMBus--D31:F3) Register Offset: SMB_BASE + 0Ch Default Value: 00h Lockable: No Bit 7:2 Datasheet Attribute: R/WC, RO Size: 8 bits Power Well:Resume Description Reserved 1 SMBus TCO Mode (STCO)--RO. This bit reflects the strap setting of TCO compatible mode versus Advanced TCO mode. 0 = The PCH is in the compatible TCO mode. 1 = The PCH is in the advanced TCO mode. 0 CRC Error (CRCE)--R/WC. 0 = Software clears this bit by writing a 1 to it. 1 = This bit is set if a received message contained a CRC error. When this bit is set, the DERR bit of the host status register will also be set. This bit will be set by the controller if a software abort occurs in the middle of the CRC portion of the cycle or an abort happens after the PCH has received the final data bit transmitted by an external slave. 673 SMBus Controller Registers (D31:F3) 18.2.12 AUX_CTL--Auxiliary Control Register (SMBus--D31:F3) Register Offset: SMB_BASE + 0Dh Default Value: 00h Lockable: No Bit 7:2 18.2.13 Attribute: R/W Size: 8 bits Power Well:Resume Description Reserved 1 Enable 32-Byte Buffer (E32B)--R/W. 0 = Disable. 1 = Enable. When set, the Host Block Data register is a pointer into a 32-byte buffer, as opposed to a single register. This enables the block commands to transfer or receive up to 32-bytes before the PCH generates an interrupt. 0 Automatically Append CRC (AAC)--R/W. 0 = The PCH will Not automatically append the CRC. 1 = The PCH will automatically append the CRC. This bit must not be changed during SMBus transactions or undetermined behavior will result. It should be programmed only once during the lifetime of the function. SMLINK_PIN_CTL--SMLink Pin Control Register (SMBus--D31:F3) Register Offset: SMB_BASE + 0Eh Default Value: See Description Attribute: Size: Note: This register is in the resume well and is reset by RSMRST#. Note: This register is only applicable in the TCO compatible mode. Bit 7:3 674 R/W, RO 8 bits Description Reserved 2 SMLINK_CLK_CTL--R/W. 0 = The PCH will drive the SMLink0 pin low, independent of what the other SMLink logic would otherwise indicate for the SMLink0 pin. 1 = The SMLink0 pin is not overdriven low. The other SMLink logic controls the state of the pin. (Default) 1 SMLINK1_CUR_STS--RO. This read-only bit has a default value that is dependent on an external signal level. This pin returns the value on the SMLink1 pin. This allows software to read the current state of the pin. 0 = Low 1 = High 0 SMLINK0_CUR_STS--RO. This read-only bit has a default value that is dependent on an external signal level. This pin returns the value on the SMLink0 pin. This allows software to read the current state of the pin. 0 = Low 1 = High Datasheet SMBus Controller Registers (D31:F3) 18.2.14 SMBus_PIN_CTL--SMBus Pin Control Register (SMBus--D31:F3) Register Offset: SMB_BASE + 0Fh Default Value: See Description Note: 7:3 Description Reserved 2 SMBCLK_CTL--R/W. 1 = The SMBCLK pin is not overdriven low. The other SMBus logic controls the state of the pin. 0 = The PCH drives the SMBCLK pin low, independent of what the other SMB logic would otherwise indicate for the SMBCLK pin. (Default) 1 SMBDATA_CUR_STS--RO. This read-only bit has a default value that is dependent on an external signal level. This pin returns the value on the SMBDATA pin. This allows software to read the current state of the pin. 0 = Low 1 = High 0 SMBCLK_CUR_STS--RO. This read-only bit has a default value that is dependent on an external signal level. This pin returns the value on the SMBCLK pin. This allows software to read the current state of the pin. 0 = Low 1 = High SLV_STS--Slave Status Register (SMBus--D31:F3) Register Offset: SMB_BASE + 10h Default Value: 00h Note: R/W, RO 8 bits This register is in the resume well and is reset by RSMRST#. Bit 18.2.15 Attribute: Size: Attribute: Size: R/WC 8 bits This register is in the resume well and is reset by RSMRST#. All bits in this register are implemented in the 64 kHz clock domain. Therefore, software must poll this register until a write takes effect before assuming that a write has completed internally. Bit 7:1 0 Datasheet Description Reserved HOST_NOTIFY_STS--R/WC. The PCH sets this bit to a 1 when it has completely received a successful Host Notify Command on the SMBus pins. Software reads this bit to determine that the source of the interrupt or SMI# was the reception of the Host Notify Command. Software clears this bit after reading any information needed from the Notify address and data registers by writing a 1 to this bit. The PCH will allow the Notify Address and Data registers to be over-written once this bit has been cleared. When this bit is 1, the PCH will NACK the first byte (host address) of any new "Host Notify" commands on the SMBus pins. Writing a 0 to this bit has no effect. 675 SMBus Controller Registers (D31:F3) 18.2.16 SLV_CMD--Slave Command Register (SMBus--D31:F3) Register Offset: SMB_BASE + 11h Default Value: 00h Note: 7:2 Description Reserved 2 SMBALERT_DIS--R/W. 0 = Allows the generation of the interrupt or SMI#. 1 = Software sets this bit to block the generation of the interrupt or SMI# due to the SMBALERT# source. This bit is logically inverted and ANDed with the SMBALERT_STS bit (offset SMB_BASE + 00h, bit 5). The resulting signal is distributed to the SMI# and/or interrupt generation logic. This bit does not effect the wake logic. 1 HOST_NOTIFY_WKEN--R/W. Software sets this bit to 1 to enable the reception of a Host Notify command as a wake event. When enabled this event is "OR'd" in with the other SMBus wake events and is reflected in the SMB_WAK_STS bit of the General Purpose Event 0 Status register. 0 = Disable 1 = Enable 0 HOST_NOTIFY_INTREN--R/W. Software sets this bit to 1 to enable the generation of interrupt or SMI# when HOST_NOTIFY_STS (offset SMB_BASE + 10h, bit 0) is 1. This enable does not affect the setting of the HOST_NOTIFY_STS bit. When the interrupt is generated, either PIRQB# or SMI# is generated, depending on the value of the SMB_SMI_EN bit (D31:F3:40h, bit 1). If the HOST_NOTIFY_STS bit is set when this bit is written to a 1, then the interrupt (or SMI#) will be generated. The interrupt (or SMI#) is logically generated by AND'ing the STS and INTREN bits. 0 = Disable 1 = Enable NOTIFY_DADDR--Notify Device Address Register (SMBus--D31:F3) Register Offset: SMB_BASE + 14h Default Value: 00h Note: Attribute: Size: 7:1 0 Description DEVICE_ADDRESS--RO. This field contains the 7-bit device address received during the Host Notify protocol of the SMBus 2.0 Specification. Software should only consider this field valid when the HOST_NOTIFY_STS bit (D31:F3:SMB_BASE +10, bit 0) is set to 1. Reserved NOTIFY_DLOW--Notify Data Low Byte Register (SMBus--D31:F3) Register Offset: SMB_BASE + 16h Default Value: 00h Note: Attribute: Size: RO 8 bits This register is in the resume well and is reset by RSMRST#. Bit 7:0 676 RO 8 bits This register is in the resume well and is reset by RSMRST#. Bit 18.2.18 R/W 8 bits This register is in the resume well and is reset by RSMRST#. Bit 18.2.17 Attribute: Size: Description DATA_LOW_BYTE--RO. This field contains the first (low) byte of data received during the Host Notify protocol of the SMBus 2.0 specification. Software should only consider this field valid when the HOST_NOTIFY_STS bit (D31:F3:SMB_BASE +10, bit 0) is set to 1. Datasheet SMBus Controller Registers (D31:F3) 18.2.19 NOTIFY_DHIGH--Notify Data High Byte Register (SMBus--D31:F3) Register Offset: SMB_BASE + 17h Default Value: 00h Note: Attribute: Size: RO 8 bits This register is in the resume well and is reset by RSMRST#. Bit 7:0 Description DATA_HIGH_BYTE--RO. This field contains the second (high) byte of data received during the Host Notify protocol of the SMBus 2.0 specification. Software should only consider this field valid when the HOST_NOTIFY_STS bit (D31:F3:SMB_BASE +10, bit 0) is set to 1. Datasheet 677 PCI Express* Configuration Registers 19 PCI Express* Configuration Registers 19.1 PCI Express* Configuration Registers (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Note: This section assumes the default PCI Express Function Number-to-Root Port mapping is used. Function numbers for a given root port are assignable through the Root Port Function Number and Hide for PCI Express Root Ports register (RCBA+0404h). Note: Register address locations that are not shown in Table 19-1 should be treated as Reserved. Table 19-1. PCI Express* Configuration Registers Address Map (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) (Sheet 1 of 2) 678 Function 0-7 Default Attribute Vendor Identification 8086h RO Device Identification See register description RO Offset Mnemonic Register Name 00h-01h VID 02h-03h DID 04h-05h PCICMD PCI Command 0000h R/W, RO 06h-07h PCISTS PCI Status 0010h R/WC, RO 08h RID Revision Identification See register description RO RO 09h PI Programming Interface 00h 0Ah SCC Sub Class Code 04h RO 0Bh BCC Base Class Code 06h RO 0Ch CLS Cache Line Size 00h R/W 0Dh PLT Primary Latency Timer 00h RO 0Eh HEADTYP Header Type 81h RO 18h-1Ah BNUM Bus Number 000000h R/W 1Bh SLT 00h RO Secondary Latency Timer 1Ch-1Dh IOBL I/O Base and Limit 0000h R/W, RO 1Eh-1Fh SSTS Secondary Status Register 0000h R/WC 20h-23h MBL Memory Base and Limit 00000000h R/W 24h-27h PMBL Prefetchable Memory Base and Limit 00010001h R/W, RO 28h-2Bh PMBU32 Prefetchable Memory Base Upper 32 Bits 00000000h R/W 2Ch-2Fh PMLU32 Prefetchable Memory Limit Upper 32 Bits 00000000h R/W 34h CAPP Capabilities List Pointer 3Ch-3Dh INTR Interrupt Information 40h RO See bit description R/W, RO R/W 3Eh-3Fh BCTRL Bridge Control Register 0000h 40h-41h CLIST Capabilities List 8010h RO 42h-43h XCAP PCI Express* Capabilities 0042h R/WO, RO 44h-47h DCAP Device Capabilities 00008000h RO 48h-49h DCTL Device Control 0000h R/W, RO Datasheet PCI Express* Configuration Registers Table 19-1. PCI Express* Configuration Registers Address Map (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) (Sheet 2 of 2) Datasheet Offset Mnemonic Register Name 4Ah-4Bh DSTS Device Status 4Ch-4Fh LCAP Link Capabilities 50h-51h LCTL 52h-53h LSTS 54h-57h 58h-59h 5Ah-5Bh Function 0-7 Default Attribute 0010h R/WC, RO See bit description RO, R/WO Link Control 0000h R/W, RO Link Status See bit description RO SLCAP Slot Capabilities Register 00060060h R/WO, RO SLCTL Slot Control 0000h R/W, RO SLSTS Slot Status 0000h R/WC, RO 5Ch-5Dh RCTL Root Control 0000h R/W 60h-63h RSTS Root Status 00000000h R/WC, RO 64h-67h DCAP2 Device Capabilities 2 Register 00080816h R/WO,RO 68h-69h DCTL2 Device Control 2 Register 0000h R/W, RO 70h-71h LCTL2 Link Control 2 Register 0002h R/W 72h-73h LSTS2 Link Status 2 Register 0000h RO 80h-81h MID Message Signaled Interrupt Identifiers 9005h RO 82h-83h MC Message Signaled Interrupt Message Control 0000h R/W, RO 84h-87h MA Message Signaled Interrupt Message Address 00000000h R/W 88h-89h MD Message Signaled Interrupt Message Data 0000h R/W 90h-91h SVCAP Subsystem Vendor Capability A00Dh R/WO,RO 94h-97h SVID 00000000h R/WO A0h-A1h PMCAP A2h-A3h PMC Subsystem Vendor Identification Power Management Capability 0001h RO PCI Power Management Capability C803h RO A4h-A7h PMCS PCI Power Management Control and Status 00000000h R/W, RO D4h-D7h MPC2 Miscellaneous Port Configuration 2 00000800h R/W, RO D8h-dBh MPC Miscellaneous Port Configuration 09110000h R/W, RO, R/ WO SMI/SCI Status Register 00000000h R/WC 00h R/W PCI Express Configuration Register 3 00000000h R/W Uncorrectable Error Status See bit description R/WC, RO PCI Express* Configuration Register 4 See bit description R/W DCh-DFh SMSCS E1h RPDCGEN ECh-EFh PECR3 104h-107h UES FCh-FFh PECR4 108h-10Bh UEM Uncorrectable Error Mask 00000000h R/WO, RO 10Ch-10Fh UEV Uncorrectable Error Severity 00060011h RO Rort Port Dynamic Clock Gating Enable 110h-113h CES Correctable Error Status 00000000h R/WC 114h-117h CEM Correctable Error Mask 00002000h R/WO 118h-11Bh AECC Advanced Error Capabilities and Control 00000000h RO 130h-133h RES Root Error Status 00000000h R/WC, RO 320h-323h PECR2 PCI Express Configuration Register 2 0004B05Bh R/W 324h-327h PEETM PCI Express Extended Test Mode Register See bit description RO 330h-333h PEC1 PCI Express Configuration Register 1 28000016h RO, R/W 679 PCI Express* Configuration Registers 19.1.1 VID--Vendor Identification Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 00h-01h Default Value: 8086h Attribute: Size: Bit 15:0 19.1.2 Description Vendor ID--RO. This is a 16-bit value assigned to Intel. Intel VID = 8086h DID--Device Identification Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 02h-03h Default Value: Port 1= Bit Port 2= Bit Port 3= Bit Port 4= Bit Port 5= Bit Port 6= Bit Port 7= Bit Port 8= Bit 680 RO 16 bits Attribute: Size: Description Description Description Description Description Description Description Description RO 16 bits Bit Description 15:0 Device ID--RO. This is a 16-bit value assigned to the PCH's PCI Express controller. See Section 1.3 for the value of the DID Register. Datasheet PCI Express* Configuration Registers 19.1.3 PCICMD--PCI Command Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 04h-05h Default Value: 0000h Bit 15:11 10 Attribute: Size: R/W, RO 16 bits Description Reserved Interrupt Disable--R/W. This disables pin-based INTx# interrupts on enabled Hot-Plug and power management events. This bit has no effect on MSI operation. 0 = Internal INTx# messages are generated if there is an interrupt for Hot-Plug or power management and MSI is not enabled. 1 = Internal INTx# messages will not be generated. This bit does not affect interrupt forwarding from devices connected to the root port. Assert_INTx and Deassert_INTx messages will still be forwarded to the internal interrupt controllers if this bit is set. 9 Fast Back to Back Enable (FBE)--Reserved per the PCI Express* Base Specification. 8 SERR# Enable (SEE)--R/W. 0 = Disable. 1 = Enables the root port to generate an SERR# message when PSTS.SSE is set. 7 Wait Cycle Control (WCC)--Reserved per the PCI Express Base Specification. 6 Parity Error Response (PER)--R/W. 0 = Disable. 1 = Indicates that the device is capable of reporting parity errors as a master on the backbone. 5 VGA Palette Snoop (VPS)--Reserved per the PCI Express* Base Specification. 4 Postable Memory Write Enable (PMWE)--Reserved per the PCI Express* Base Specification. 3 Special Cycle Enable (SCE)--Reserved per the PCI Express* Base Specification. 2 Bus Master Enable (BME)--R/W. 0 = Disable. Memory and I/O requests received at a Root Port must be handled as Unsupported Requests. 1 = Enable. Allows the root port to forward Memory and I/O Read/Write cycles onto the backbone from a PCI Express* device. Note: Datasheet This bit does not affect forwarding of completions in either upstream or downstream direction nor controls forwarding of requests other than memory or I/O 1 Memory Space Enable (MSE)--R/W. 0 = Disable. Memory cycles within the range specified by the memory base and limit registers are master aborted on the backbone. 1 = Enable. Allows memory cycles within the range specified by the memory base and limit registers can be forwarded to the PCI Express device. 0 I/O Space Enable (IOSE)--R/W. This bit controls access to the I/O space registers. 0 = Disable. I/O cycles within the range specified by the I/O base and limit registers are master aborted on the backbone. 1 = Enable. Allows I/O cycles within the range specified by the I/O base and limit registers can be forwarded to the PCI Express device. 681 PCI Express* Configuration Registers 19.1.4 PCISTS--PCI Status Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 06h-07h Default Value: 0010h R/WC, RO 16 bits Bit Description 15 Detected Parity Error (DPE)--R/WC. 0 = No parity error detected. 1 = Set when the root port receives a command or data from the backbone with a parity error. This is set even if PCIMD.PER (D28:F0/F1/F2/F3:04, bit 6) is not set. 14 Signaled System Error (SSE)--R/WC. 0 = No system error signaled. 1 = Set when the root port signals a system error to the internal SERR# logic. 13 Received Master Abort (RMA)--R/WC. 0 = Root port has not received a completion with unsupported request status from the backbone. 1 = Set when the root port receives a completion with unsupported request status from the backbone. 12 Received Target Abort (RTA)--R/WC. 0 = Root port has not received a completion with completer abort from the backbone. 1 = Set when the root port receives a completion with completer abort from the backbone. 11 Signaled Target Abort (STA)--R/WC. 0 = No target abort received. 1 = Set whenever the root port forwards a target abort received from the downstream device onto the backbone. 10:9 DEVSEL# Timing Status (DEV_STS)--Reserved per the PCI Express* Base Specification. 8 Master Data Parity Error Detected (DPED)--R/WC. 0 = No data parity error received. 1 = Set when the root port receives a completion with a data parity error on the backbone and PCIMD.PER (D28:F0/F1/F2/F3:04, bit 6) is set. 7 Fast Back to Back Capable (FB2BC)--Reserved per the PCI Express* Base Specification. 6 Reserved 5 66 MHz Capable--Reserved per the PCI Express* Base Specification. 4 Capabilities List--RO. Hardwired to 1. Indicates the presence of a capabilities list. 3 Interrupt Status--RO. Indicates status of Hot-Plug and power management interrupts on the root port that result in INTx# message generation. 0 = Interrupt is de-asserted. 1 = Interrupt is asserted. This bit is not set if MSI is enabled. If MSI is not enabled, this bit is set regardless of the state of PCICMD.Interrupt Disable bit (D28:F0/F1/F2/F3/F4/F5/F6/F7/F6/F7:04h:bit 10). 2:0 682 Attribute: Size: Reserved Datasheet PCI Express* Configuration Registers 19.1.5 RID--Revision Identification Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Offset Address: 08h Default Value: See bit description 19.1.6 Attribute: Size: Bit Description 7:0 Revision ID--RO. This field indicates the device specific revision identifier. See Section 1.3 for the value of the RID Register. PI--Programming Interface Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 09h Default Value: 00h Bit 7:0 19.1.7 Attribute: Size: Programming Interface--RO. 00h = No specific register level programming interface defined. SCC--Sub Class Code Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Attribute: Size: RO 8 bits Bit Description 7:0 Sub Class Code (SCC)--RO. This field is determined by bit 2 of the MPC register (D28:F0-5:Offset D8h, bit 2). 04h = PCI-to-PCI bridge. 00h = Host Bridge. BCC--Base Class Code Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 0Bh Default Value: 06h Bit 7:0 Datasheet RO 8 bits Description Address Offset: 0Ah Default Value: 04h 19.1.8 RO 8 bits Attribute: Size: RO 8 bits Description Base Class Code (BCC)--RO. 06h = Indicates the device is a bridge device. 683 PCI Express* Configuration Registers 19.1.9 CLS--Cache Line Size Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 0Ch Default Value: 00h Bit 7:0 19.1.10 Attribute: Size: Description Cache Line Size (CLS)--R/W. This is read/write but contains no functionality, per the PCI Express* Base Specification. PLT--Primary Latency Timer Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 0Dh Default Value: 00h Bit 19.1.11 Attribute: Size: RO 8 bits Description 7:3 Latency Count. Reserved per the PCI Express* Base Specification. 2:0 Reserved HEADTYP--Header Type Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 0Eh Default Value: 81h Bit 7 6:0 684 R/W 8 bits Attribute: Size: RO 8 bits Description Multi-Function Device--RO. 0 = Single-function device. 1 = Multi-function device. Configuration Layout--RO. This field is determined by bit 2 of the MPC register (D28:F0-5:Offset D8h, bit 2). 00h = Indicates a Host Bridge. 01h = Indicates a PCI-to-PCI bridge. Datasheet PCI Express* Configuration Registers 19.1.12 BNUM--Bus Number Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 18-1Ah Default Value: 000000h Bit 23:16 15:8 7:0 19.1.13 Attribute: Size: Description Subordinate Bus Number (SBBN)--R/W. Indicates the highest PCI bus number below the bridge. Secondary Bus Number (SCBN)--R/W. Indicates the bus number the port. Primary Bus Number (PBN)--R/W. Indicates the bus number of the backbone. SLT--Secondary Latency Timer Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 1Bh Default Value: 00h Bit 7:0 19.1.14 Attribute: Size: RO 8 bits Description Secondary Latency Timer--Reserved for a Root Port per the PCI Express* Base Specification. IOBL--I/O Base and Limit Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 1Ch-1Dh Default Value: 0000h Bit 15:12 11:8 Datasheet R/W 24 bits Attribute: Size: R/W, RO 16 bits Description I/O Limit Address (IOLA)--R/W. I/O Base bits corresponding to address lines 15:12 for 4-KB alignment. Bits 11:0 are assumed to be padded to FFFh. I/O Limit Address Capability (IOLC)--RO. Indicates that the bridge does not support 32-bit I/O addressing. 7:4 I/O Base Address (IOBA)--R/W. I/O Base bits corresponding to address lines 15:12 for 4-KB alignment. Bits 11:0 are assumed to be padded to 000h. 3:0 I/O Base Address Capability (IOBC)--RO. Indicates that the bridge does not support 32-bit I/O addressing. 685 PCI Express* Configuration Registers 19.1.15 SSTS--Secondary Status Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 1Eh-1Fh Default Value: 0000h Bit R/WC 16 bits Description 15 Detected Parity Error (DPE)--R/WC. 0 = No error. 1 = The port received a poisoned TLP. 14 Received System Error (RSE)--R/WC. 0 = No error. 1 = The port received an ERR_FATAL or ERR_NONFATAL message from the device. 13 Received Master Abort (RMA)--R/WC. 0 = Unsupported Request not received. 1 = The port received a completion with "Unsupported Request" status from the device. 12 Received Target Abort (RTA)--R/WC. 0 = Completion Abort not received. 1 = The port received a completion with "Completion Abort" status from the device. 11 Signaled Target Abort (STA)--R/WC. 0 = Completion Abort not sent. 1 = The port generated a completion with "Completion Abort" status to the device. 10:9 Secondary DEVSEL# Timing Status (SDTS): Reserved per PCI Express* Base Specification. 8 Data Parity Error Detected (DPD)--R/WC. 0 = Conditions below did not occur. 1 = Set when the BCTRL.PERE (D28:FO/F1/F2/F3/F4/F5:3E: bit 0) is set, and either of the following two conditions occurs: *Port receives completion marked poisoned. *Port poisons a write request to the secondary side. 7 Secondary Fast Back to Back Capable (SFBC): Reserved per PCI Express* Base Specification. 6 Reserved 5 Secondary 66 MHz Capable (SC66): Reserved per PCI Express* Base Specification. 4:0 686 Attribute: Size: Reserved Datasheet PCI Express* Configuration Registers 19.1.16 MBL--Memory Base and Limit Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 20h-23h Default Value: 00000000h Attribute: Size: R/W 32 bits Accesses that are within the ranges specified in this register will be sent to the attached device if CMD.MSE (D28:F0~F7:04:bit 1) is set. Accesses from the attached device that are outside the ranges specified will be forwarded to the backbone if CMD.BME (D28:F0~F7:04:bit 2) is set. The comparison performed is MB AD[31:20] ML. Bit 31:20 Memory Limit (ML)--R/W. These bits are compared with bits 31:20 of the incoming address to determine the upper 1-MB aligned value of the range. 19:16 Reserved 15:4 3:0 19.1.17 Description Memory Base (MB)--R/W. These bits are compared with bits 31:20 of the incoming address to determine the lower 1-MB aligned value of the range. Reserved PMBL--Prefetchable Memory Base and Limit Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 24h-27h Default Value: 00010001h Attribute: Size: R/W, RO 32 bits Accesses that are within the ranges specified in this register will be sent to the device if CMD.MSE (D28:F0~F7;04, bit 1) is set. Accesses from the device that are outside the ranges specified will be forwarded to the backbone if CMD.BME (D28:F0~F7;04, bit 2) is set. The comparison performed is PMBU32:PMB AD[63:32]:AD[31:20] PMLU32:PML. Bit 31:20 Prefetchable Memory Limit (PML)--R/W. These bits are compared with bits 31:20 of the incoming address to determine the upper 1-MB aligned value of the range. 19:16 64-bit Indicator (I64L)--RO. Indicates support for 64-bit addressing 15:4 3:0 19.1.18 Description Prefetchable Memory Base (PMB)--R/W. These bits are compared with bits 31:20 of the incoming address to determine the lower 1-MB aligned value of the range. 64-bit Indicator (I64B)--RO. Indicates support for 64-bit addressing PMBU32--Prefetchable Memory Base Upper 32 Bits Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 28h-2Bh Default Value: 00000000h Bit 31:0 Datasheet Attribute: Size: R/W 32 bits Description Prefetchable Memory Base Upper Portion (PMBU)--R/W. Upper 32-bits of the prefetchable address base. 687 PCI Express* Configuration Registers 19.1.19 PMLU32--Prefetchable Memory Limit Upper 32 Bits Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 2Ch-2Fh Default Value: 00000000h Attribute: Size: Bit 31:0 19.1.20 Description Prefetchable Memory Limit Upper Portion (PMLU)--R/W. Upper 32-bits of the prefetchable address limit. CAPP--Capabilities List Pointer Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 34h Default Value: 40h 19.1.21 Attribute: Size: RWO 8 bits Bit Description 7:0 Capabilities Pointer (PTR)--RO. Indicates that the pointer for the first entry in the capabilities list is at 40h in configuration space. INTR--Interrupt Information Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 3Ch-3Dh Default Value: See bit description Function Level Reset:No (Bits 7:0 only) Bit 15:8 R/W, RO 16 bits Interrupt Pin (IPIN)--RO. Indicates the interrupt pin driven by the root port. At reset, this register takes on the following values that reflect the reset state of the D28IP register in chipset config space: Port Reset Value 1 D28IP.P1IP 2 D28IP.P2IP 3 D28IP.P3IP 4 D28IP.P4IP 5 D28IP.P5IP 6 D28IP.P6IP 7 D28IP.P7IP Note: 7:0 Attribute: Size: Description 8 688 R/W 32 bits D28IP.P8IP The value that is programmed into D28IP is always reflected in this register. Interrupt Line (ILINE)--R/W. Default = 00h. Software written value to indicate which interrupt line (vector) the interrupt is connected to. No hardware action is taken on this register. These bits are not reset by FLR. Datasheet PCI Express* Configuration Registers 19.1.22 BCTRL--Bridge Control Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 3Eh-3Fh Default Value: 0000h Bit 15:12 19.1.23 Attribute: Size: Description Reserved 11 Discard Timer SERR# Enable (DTSE): Reserved per PCI Express* Base Specification, Revision 1.0a 10 Discard Timer Status (DTS): Reserved per PCI Express* Base Specification, Revision 1.0a. 9 Secondary Discard Timer (SDT): Reserved per PCI Express* Base Specification, Revision 1.0a. 8 Primary Discard Timer (PDT): Reserved per PCI Express* Base Specification, Revision 1.0a. 7 Fast Back to Back Enable (FBE): Reserved per PCI Express* Base Specification, Revision 1.0a. 6 Secondary Bus Reset (SBR)--R/W. Triggers a hot reset on the PCI Express* port. 5 Master Abort Mode (MAM): Reserved per Express specification. 4 VGA 16-Bit Decode (V16)--R/W. 0 = VGA range is enabled. 1 = The I/O aliases of the VGA range (see BCTRL:VE definition below), are not enabled, and only the base I/O ranges can be decoded. 3 VGA Enable (VE)--R/W. 0 = The ranges below will not be claimed off the backbone by the root port. 1 = The following ranges will be claimed off the backbone by the root port: * Memory ranges A0000h-BFFFFh * I/O ranges 3B0h - 3BBh and 3C0h - 3DFh, and all aliases of bits 15:10 in any combination of 1s 2 ISA Enable (IE)--R/W. This bit only applies to I/O addresses that are enabled by the I/O Base and I/O Limit registers and are in the first 64 KB of PCI I/O space. 0 = The root port will not block any forwarding from the backbone as described below. 1 = The root port will block any forwarding from the backbone to the device of I/O transactions addressing the last 768 bytes in each 1-KB block (offsets 100h to 3FFh). 1 SERR# Enable (SE)--R/W. 0 = The messages described below are not forwarded to the backbone. 1 = ERR_COR, ERR_NONFATAL, and ERR_FATAL messages received are forwarded to the backbone. 0 Parity Error Response Enable (PERE)--R/W. When set, 0 = Poisoned write TLPs and completions indicating poisoned TLPs will not set the SSTS.DPD (D28:F0/F1/F2/F3/F4/F5/F6/F7:1E, bit 8). 1 = Poisoned write TLPs and completions indicating poisoned TLPs will set the SSTS.DPD (D28:F0/ F1/F2/F3/F4/F5/F6/F7:1E, bit 8). CLIST--Capabilities List Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 40-41h Default Value: 8010h Attribute: Size: R/WO, RO 16 bits Bit Description 15:8 Next Capability (NEXT)--RWO. Indicates the location of the next pointer. The default value of this register is 80h, which points to the MSI Capability structure. Since this is a RWO register, BIOS must write a value to this register, even if it is to re-write the default value. 7:0 Datasheet R/W 16 bits Capability ID (CID)--RO. Indicates this is a PCI Express* capability. 689 PCI Express* Configuration Registers 19.1.24 XCAP--PCI Express* Capabilities Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 42h-43h Default Value: 0042h Bit 15:14 13:9 8 19.1.25 Attribute: Size: Description Reserved Interrupt Message Number (IMN)--RO. The PCH does not have multiple MSI interrupt numbers. Slot Implemented (SI)--R/WO. Indicates whether the root port is connected to a slot. Slot support is platform specific. BIOS programs this field, and it is maintained until a platform reset. 7:4 Device / Port Type (DT)--RO. Indicates this is a PCI Express* root port. 3:0 Capability Version (CV)--RO. Indicates PCI Express 2.0. DCAP--Device Capabilities Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 44h-47h Default Value: 00008000h Bit 31:28 Attribute: Size: Reserved 27:26 Captured Slot Power Limit Scale (CSPS)--RO. Not supported. Captured Slot Power Limit Value (CSPV)--RO. Not supported. 17:16 Reserved 14:12 R/WO, RO 32 bits Description 25:18 15 Role Based Error Reporting (RBER)--RO. Indicates that this device implements the functionality defined in the Error Reporting ECN as required by the PCI Express 2.0 specification. Reserved 11:9 Endpoint L1 Acceptable Latency (E1AL)--RO. This field is reserved with a setting of 000b for devices other than Endpoints, per the PCI Express 2.0 Spec. 8:6 Endpoint L0 Acceptable Latency (E0AL)--RO. This field is reserved with a setting of 000b for devices other than Endpoints, per the PCI Express 2.0 Spec. 5 690 R/WO, RO 16 bits Extended Tag Field Supported (ETFS)--RO. Indicates that 8-bit tag fields are supported. 4:3 Phantom Functions Supported (PFS)--RO. No phantom functions supported. 2:0 Max Payload Size Supported (MPS)--RWO. BIOS should write to this field during system initialization. Only a maximum payload size of 128B is supported. Programming this field to any value other than 000b (128B) will result in aliasing to 128B max payload size. Datasheet PCI Express* Configuration Registers 19.1.26 DCTL--Device Control Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 48h-49h Default Value: 0000h Bit 15 14:12 R/W, RO 16 bits Description Reserved Max Read Request Size (MRRS)--RO. Hardwired to 0. 11 Enable No Snoop (ENS)--RO. Not supported. The root port will never issue non-snoop requests. 10 Aux Power PM Enable (APME)--R/W. The OS will set this bit to 1 if the device connected has detected aux power. It has no effect on the root port otherwise. 9 8 7:5 Datasheet Attribute: Size: Phantom Functions Enable (PFE)--RO. Not supported. Extended Tag Field Enable (ETFE)--RO. Not supported. Max Payload Size (MPS)--R/W. The root port only supports 128B max payloads, regardless of the programming of this field. Programming this field to any value other than 000b (128B) will result in aliasing to 128B max payload size. BIOS should program this field prior to enabling BME. 4 Enable Relaxed Ordering (ERO)--RO. Not supported. 3 Unsupported Request Reporting Enable (URE)--R/W. 0 = The root port will ignore unsupported request errors. 1 = Allows signaling ERR_NONFATAL, ERR_FATAL, or ERR_COR to the Root Control register when detecting an unmasked Unsupported Request (UR). An ERR_COR is signaled when a unmasked Advisory Non-Fatal UR is received. An ERR_FATAL, ERR_or NONFATAL, is sent to the Root Control Register when an uncorrectable non-Advisory UR is received with the severity set by the Uncorrectable Error Severity register. 2 Fatal Error Reporting Enable (FEE)--R/W. 0 = The root port will ignore fatal errors. 1 = Enables signaling of ERR_FATAL to the Root Control register due to internally detected errors or error messages received across the link. Other bits also control the full scope of related error reporting. 1 Non-Fatal Error Reporting Enable (NFE)--R/W. 0 = The root port will ignore non-fatal errors. 1 = Enables signaling of ERR_NONFATAL to the Root Control register due to internally detected errors or error messages received across the link. Other bits also control the full scope of related error reporting. 0 Correctable Error Reporting Enable (CEE)--R/W. 0 = The root port will ignore correctable errors. 1 = Enables signaling of ERR_CORR to the Root Control register due to internally detected errors or error messages received across the link. Other bits also control the full scope of related error reporting. 691 PCI Express* Configuration Registers 19.1.27 DSTS--Device Status Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 4Ah-4Bh Default Value: 0010h Attribute: Size: Bit 15:6 19.1.28 Description Reserved 5 Transactions Pending (TDP)--RO. This bit has no meaning for the root port since only one transaction may be pending to the PCH, so a read of this bit cannot occur until it has already returned to 0. 4 AUX Power Detected (APD)--RO. The root port contains AUX power for wakeup. 3 Unsupported Request Detected (URD)--R/WC. Indicates an unsupported request was detected. 2 Fatal Error Detected (FED)--R/WC. Indicates a fatal error was detected. 0 = Fatal has not occurred. 1 = A fatal error occurred from a data link protocol error, link training error, buffer overflow, or malformed TLP. 1 Non-Fatal Error Detected (NFED)--R/WC. Indicates a non-fatal error was detected. 0 = Non-fatal has not occurred. 1 = A non-fatal error occurred from a poisoned TLP, unexpected completions, unsupported requests, completer abort, or completer timeout. 0 Correctable Error Detected (CED)--R/WC. Indicates a correctable error was detected. 0 = Correctable has not occurred. 1 = The port received an internal correctable error from receiver errors / framing errors, TLP CRC error, DLLP CRC error, replay num rollover, replay timeout. LCAP--Link Capabilities Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 4Ch-4Fh Default Value: See bit description Attribute: Size: Bit 31:24 23:22 692 R/WC, RO 16 bits R/WO, RO/V, RO 32 bits Description Port Number (PN)--RO/V. Indicates the port number for the root port. This value is different for each implemented port: Function Port # Value of PN Field D28:F0 1 01h D28:F1 2 02h D28:F2 3 03h D28:F3 4 04h D28:F4 5 05h D28:F5 6 06h D28:F6 7 07h D28:F7 8 08h Reserved 21 Link Bandwidth Notification Capability (LBNC)--RO. Hardwired to 1b to indicate that this port supports Link Bandwidth Notification status and interrupt mechanisms. 20 Link Active Reporting Capable (LARC)--RO. Hardwired to 1b to indicate that this port supports the optional capability of reporting the DL_Active state of the Data Link Control and Management State Machine. Datasheet PCI Express* Configuration Registers Bit Description 19 Reserved 18 Clock Power Management (CPM)--RO. 0 = PCH root ports do not support the CLKREQ# mechanism. 1 = PCH root ports support the CLKREQ# mechanism. 17:15 L1 Exit Latency (EL1)--R/WO. Indicates an exit latency of 2us to 4us. 000b = Less than 1us 001b = 1 us to less than 2 us 010b = 2 us to less than 4 us 011b = 4 us to less than 8 us 100b = 8 us to less than 16 us 101b = 16 us to less than 32 us 110b = 32 us to 64 us 111b = more than 64 us Note: If PXP PLL shutdown is enabled, BIOS should program this latency to comprehend PLL lock latency. 14:12 L0s Exit Latency (EL0)--RO/V. Indicates an exit latency based upon common-clock configuration. LCLT.CCC Value of EL0 (these bits) 0 MPC.UCEL (D28:F0~F7:D8h:bits20:18) 1 MPC.CCEL (D28:F0~F7:D8h:bits17:15) Note: 11:10 LCLT.CCC is at D28:F0~F7:50h:bit 6. Active State Power Management Support (APMS)--R/WO. Indicates what level of active state link power management is supported on the root port. Note: In a SKU where ASPM control is disabled, the default value of this field is hard wired to 01b, regardless of any value the BIOS writes to this field. Otherwise, the default value of this field is 11b. Value Datasheet Definition 00b Reserved 01b L0s Entry Supported 10b Reserved 11b Both L0s and L1 Entry Supported 9:4 Maximum Link Width (MLW)--RO/V. These bits are set by the PCIEPCS1[1:0] soft strap in the PCHSTRP9 record. Note: Support for 1 x2 or 1 x4 configuration on PCIe Port 1 is only available per Section 5.1 guidelines. 000011 = 1 x4: Port 1 (x4) 000010 = Reserved 000001 = 1 x2 and 2 x1s: Port 1 (x2), Port 3 (x1) and Port 4 (x1) 000000 = 4 x1s: Port 1 (x1), Port 2 (x1), Port 3 (x1) and Port 4 (x1) This bit is set by the PCIEPCS2[1:0] soft strap in the PCHSTRP9 record. 000011 = 1 x4: Port 5 (x4) 000010 = Reserved 000001 = 1 x2 and 2 x1s: Port 5 (x2), Port 7 (x1) and Port 8 (x1) 000000 = 4 x1s: Port 5 (x1), Port 6 (x1), Port 7 (x1) and Port 8 (x1) 3:0 Maximum Link Speed (MLS)--RO. 0001b = indicates the link speed is 2.5 Gb/s 0010b = 5.0 Gb/s and 2.5Gb/s link speeds supported Note: These bits report a value of 0001b if Gen2 disable bit 14 is set in the MPC register, else the value reported is 0010b 693 PCI Express* Configuration Registers 19.1.29 LCTL--Link Control Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 50h-51h Default Value: 0000h Bit 15:10 R/W, RO 16 bits Description Reserved 9 Hardware Autonomous Width Disable - RO. Hardware never attempts to change the link width except when attempting to correct unreliable Link operation. 8 Reserved 7 Extended Synch (ES)--R/W. 0 = Extended synch disabled. 1 = Forces extended transmission of FTS ordered sets in FTS and extra TS2 at exit from L1 prior to entering L0. 6 Common Clock Configuration (CCC)--R/W. 0 = The PCH and device are not using a common reference clock. 1 = The PCH and device are operating with a distributed common reference clock. Note: Non-Common Clock Mode operation is not supported on all PCI Express root ports. 5 Retrain Link (RL)--R/W. 0 = This bit always returns 0 when read. 1 = The root port will train its downstream link. Note: Software uses LSTS.LT (D28:F0/F1/F2/F3/F4/F5/F6/F7:52, bit 11) to check the status of training. Note: It is permitted to write 1b to this bit while simultaneously writing modified values to other fields in this register. If the LTSSM is not already in Recovery or Configuration, the resulting Link training must use the modified values. If the LTSSM is already in Recovery or Configuration, the modified values are not required to affect the Link training that is already in progress. 4 Link Disable (LD)--R/W. 0 = Link enabled. 1 = The root port will disable the link. 3 Read Completion Boundary Control (RCBC)--RO. Indicates the read completion boundary is 64 bytes. 2 Reserved 1:0 694 Attribute: Size: Active State Link PM Control (APMC)--R/W. Indicates whether the root port should enter L0s or L1 or both. 00 = Disabled 01 = L0s Entry Enabled 10 = L1 Entry Enabled 11 = L0s and L1 Entry Enabled Datasheet PCI Express* Configuration Registers 19.1.30 LSTS--Link Status Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 52h-53h Default Value: See bit description Bit 15:14 RO 16 bits Description Reserved 13 Data Link Layer Active (DLLA)--RO. Default value is 0b. 0 = Data Link Control and Management State Machine is not in the DL_Active state 1 = Data Link Control and Management State Machine is in the DL_Active state 12 Slot Clock Configuration (SCC)--RO. Set to 1b to indicate that the PCH uses the same reference clock as on the platform and does not generate its own clock. 11 Link Training (LT)--RO. Default value is 0b. 0 = Link training completed. 1 = Link training is occurring. 10 Link Training Error (LTE)--RO. Not supported. Set value is 0b. 9:4 Negotiated Link Width (NLW)--RO. This field indicates the negotiated width of the given PCI Express* link. The contents of this NLW field is undefined if the link has not successfully trained. Port # 000001b, 000010b, 000100b 2 000001b 3 000001b, 000010b 4 000001b 5 000001b, 000010b, 000100b 6 000001b 7 000001b, 000010b 8 3:0 Possible Values 1 Note: Datasheet Attribute: Size: 000001b 000001b = x1 link width, 000010b =x2 linkwidth, 000100b = x4 linkwidth Link Speed (LS)--RO. This field indicates the negotiated Link speed of the given PCI Express* link. 0001b = Link is 2.5 Gb/s 0010b = Link is 5.0 Gb/s 695 PCI Express* Configuration Registers 19.1.31 SLCAP--Slot Capabilities Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 54h-57h Default Value: 00060060h 696 Attribute: Size: R/WO, RO 32 bits Bit Description 31:19 Physical Slot Number (PSN)--R/WO. This is a value that is unique to the slot number. BIOS sets this field and it remains set until a platform reset. 18:17 Reserved 16:15 Slot Power Limit Scale (SLS)--R/WO. Specifies the scale used for the slot power limit value. BIOS sets this field and it remains set until a platform reset. 14:7 Slot Power Limit Value (SLV)--R/WO. Specifies the upper limit (in conjunction with SLS value), on the upper limit on power supplied by the slot. The two values together indicate the amount of power in watts allowed for the slot. BIOS sets this field and it remains set until a platform reset. 6 Hot-Plug Capable (HPC)--R/WO. 1b = Indicates that Hot-Plug is supported. 5 Hot-Plug Surprise (HPS)--R/WO. 1b = Indicates the device may be removed from the slot without prior notification. 4 Power Indicator Present (PIP)--RO. 0b = Indicates that a power indicator LED is not present for this slot. 3 Attention Indicator Present (AIP)--RO. 0b = Indicates that an attention indicator LED is not present for this slot. 2 MRL Sensor Present (MSP)--RO. 0b = Indicates that an MRL sensor is not present. 1 Power Controller Present (PCP)--RO. 0b = Indicates that a power controller is not implemented for this slot. 0 Attention Button Present (ABP)--RO. 0b = Indicates that an attention button is not implemented for this slot. Datasheet PCI Express* Configuration Registers 19.1.32 SLCTL--Slot Control Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 58h-59h Default Value: 0000h Bit 15:13 R/W, RO 16 bits Description Reserved 12 Link Active Changed Enable (LACE)--R/W. When set, this field enables generation of a Hot-Plug interrupt when the Data Link Layer Link Active field (D28:F0/F1/F2/F3/F4/F5/F6/F7:52h:bit 13) is changed. 11 Reserved 10 Power Controller Control (PCC)--RO.This bit has no meaning for module based Hot-Plug. 9:6 Reserved 5 Hot-Plug Interrupt Enable (HPE)--R/W. 0 = Hot-Plug interrupts based on Hot-Plug events is disabled. 1 = Enables generation of a Hot-Plug interrupt on enabled Hot-Plug events. 4 Reserved 3 Presence Detect Changed Enable (PDE)--R/W. 0 = Hot-Plug interrupts based on presence detect logic changes is disabled. 1 = Enables the generation of a Hot-Plug interrupt or wake message when the presence detect logic changes state. 2:0 19.1.33 Attribute: Size: Reserved SLSTS--Slot Status Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 5Ah-5Bh Default Value: 0000h Bit 15:9 8 Attribute: Size: R/WC, RO 16 bits Description Reserved Link Active State Changed (LASC)--R/WC. 1 = This bit is set when the value reported in Data Link Layer Link Active field of the Link Status register (D28:F0/F1/F2/F3/F4/F5/F6/F7:52h:bit 13) is changed. In response to a Data Link Layer State Changed event, software must read Data Link Layer Link Active field of the Link Status register to determine if the link is active before initiating configuration cycles to the hot plugged device. Datasheet 7 Reserved 6 Presence Detect State (PDS)--RO. If XCAP.SI (D28:F0/F1/F2/F3/F4/F5/F6/F7:42h:bit 8) is set (indicating that this root port spawns a slot), then this bit: 0 = Indicates the slot is empty. 1 = Indicates the slot has a device connected. Otherwise, if XCAP.SI is cleared, this bit is always set (1). 5 MRL Sensor State (MS)--Reserved as the MRL sensor is not implemented. 4 Reserved 3 Presence Detect Changed (PDC)--R/WC. 0 = No change in the PDS bit. 1 = The PDS bit changed states. 2 MRL Sensor Changed (MSC)--Reserved as the MRL sensor is not implemented. 1 Power Fault Detected (PFD)--Reserved as a power controller is not implemented. 0 Reserved 697 PCI Express* Configuration Registers 19.1.34 RCTL--Root Control Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 5Ch-5Dh Default Value: 0000h Bit 15:4 19.1.35 Attribute: Size: Description Reserved 3 PME Interrupt Enable (PIE)--R/W. 0 = Interrupt generation disabled. 1 = Interrupt generation enabled when PCISTS.Inerrupt Status (D28:F0~F7:60h, bit 16) is in a set state (either due to a 0 to 1 transition, or due to this bit being set with RSTS.IS already set). 2 System Error on Fatal Error Enable (SFE)--R/W. 0 = An SERR# will not be generated. 1 = An SERR# will be generated, assuming CMD.SEE (D28:F0~F7:04, bit 8) is set, if a fatal error is reported by any of the devices in the hierarchy of this root port, including fatal errors in this root port. 1 System Error on Non-Fatal Error Enable (SNE)--R/W. 0 = An SERR# will not be generated. 1 = An SERR# will be generated, assuming CMD.SEE (D28:F0~F7:04, bit 8) is set, if a non-fatal error is reported by any of the devices in the hierarchy of this root port, including non-fatal errors in this root port. 0 System Error on Correctable Error Enable (SCE)--R/W. 0 = An SERR# will not be generated. 1 = An SERR# will be generated, assuming CMD.SEE (D28:F0~F7:04, bit 8) if a correctable error is reported by any of the devices in the hierarchy of this root port, including correctable errors in this root port. RSTS--Root Status Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 60h-63h Default Value: 00000000h Bit 31:18 Attribute: Size: R/WC, RO 32 bits Description Reserved 17 PME Pending (PP)--RO. 0 = When the original PME is cleared by software, it will be set again, the requestor ID will be updated, and this bit will be cleared. 1 = Indicates another PME is pending when the PME status bit is set. 16 PME Status (PS)--R/WC. 0 = PME was not asserted. 1 = Indicates that PME was asserted by the requestor ID in RID. Subsequent PMEs are kept pending until this bit is cleared. 15:0 698 R/W 16 bits PME Requestor ID (RID)--RO. Indicates the PCI requestor ID of the last PME requestor. Valid only when PS is set. Datasheet PCI Express* Configuration Registers 19.1.36 DCAP2--Device Capabilities 2 Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 64h-67h Default Value: 00080816h Bit 31:12 11 10:5 4 3:0 19.1.37 Attribute: Size: Description Reserved LTR Mechanism Supported (LTRMS)--RWO. A value of 1b indicates support for the optional Latency Tolerance Reporting (LTR) mechanism. Reserved Completion Timeout Disable Supported (CTDS)--RO. A value of 1b indicates support for the Completion Timeout Disable mechanism. Completion Timeout Ranges Supported (CTRS) - RO. This field indicates device support for the optional Completion Timeout programmability mechanism. This mechanism allows system software to modify the Completion Timeout value. This field is hardwired to support 10 ms to 250 ms and 250 ms to 4 s. DCTL2--Device Control 2 Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 68h-69h Default Value: 0000h Bit 15:11 Attribute: Size: RO, R/W 16 bits Description Reserved 10 LTR Mechanism Enable (LTREN)--RW. A value of 1b enables support for the optional Latency Tolerance Reporting (LTR) mechanism. 9:5 Reserved 4 Datasheet RWO, RO 32 bits Completion Timeout Disable (CTD)--R/W. When set to 1b, this bit disables the Completion Timeout mechanism. If there are outstanding requests when the bit is cleared, it is permitted but not required for hardware to apply the completion timeout mechanism to the outstanding requests. If this is done, it is permitted to base the start time for each request on either the time this bit was cleared or the time each request was issued. 699 PCI Express* Configuration Registers Bit Description 3:0 Completion Timeout Value (CTV)--R/W. In Devices that support Completion Timeout programmability, this field allows system software to modify the Completion Timeout value. This field is applicable to Root Ports, Endpoints that issue requests on their own behalf, and PCI Express* to PCI/PCI-X Bridges that take ownership of requests issued on PCI Express. For all other devices this field is reserved and must be hardwired to 0000b. A Device that does not support this optional capability must hardwire this field to 0000b and is required to implement a timeout value in the range 50 us to 50 ms. Devices that support Completion Timeout programmability must support the values given below, corresponding to the programmability ranges indicated in the Completion Timeout Values Supported field. The PCH targeted configurable ranges are listed below, along with the range allowed by the PCI Express 2.0 specification. Defined encodings: 0000b = Default range: 40 ms to 50 ms (specification range 50 us to 50 ms) Values available if Range A (50 us to 10 ms) programmability range is supported: 0001b = 90 s to 100 s (specification range is 50 s to 100 s) 0010b = 9 ms to 10ms (specification range is 1 ms to 10 ms) Values available if Range B (10 ms to 250 ms) programmability range is supported: 0101b = 40ms to 50ms (specification range is 16 ms to 55 ms) 0110b = 160ms to 170ms (specification range is 65 ms to 210 ms) Values available if Range C (250 ms to 4s) programmability range is supported: 1001b = 400 ms to 500 ms (specification range is 260 ms to 900 ms) 1010b = 1.6 s to 1.7 s (specification range is 1 s to 3.5 s) All other values are Reserved. Note: 19.1.38 Software is permitted to change the value in this field at any time. For requests already pending when the Completion Timeout Value is changed, hardware is permitted to use either the new or the old value for the outstanding requests, and is permitted to base the start time for each request either on when this value was changed or on when each request was issued. LCTL2--Link Control 2 Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 70h-71h Default Value: 0002h Bit 15:13 700 Attribute: Size: R/W 16 bits Description Reserved 12 Compliance De-Emphasis (CD)--R/W. This bit sets the de-emphasis level in Polling.Compliance state if the entry occurred due to the Enter Compliance bit being 1b. Encodings: 0 = -6 dB 1 = -3.5 dB When the Link is operating at 2.5 GT/s, the setting of this bit has no effect. The default value of this bit is 0b. This bit is intended for debug, compliance testing purposes. System firmware and software are allowed to modify this bit only during debug or compliance testing. 11 Compliance SOS (CSOS)--R/W. When set to 1b, the LTSSM is required to send SKP Ordered Sets periodically in between the (modified) compliance patterns. The default value of this bit is 0b. Datasheet PCI Express* Configuration Registers Bit Description 10 Enter Modified Compliance (EMC)--R/W. When this bit is set to 1b, the device transmits Modified Compliance Pattern if the LTSSM enters Polling.Compliance substrate. This register is intended for debug, compliance testing purposes only and the system must ensure it is set to the default value during normal operation. The default value of this bit is 0b. 9:7 Transmit Margin (TM)--R/W. This field controls the value of the non-de-emphasized voltage level at the Transmitter pins. This field is reset to 000b on entry to the LTSSM Polling.Configuration substrate (see PCI Express Chapter 4 for details of how the Transmitter voltage level is determined in various states). Encodings: 000b: Normal operating range 001b: 800-1200 mV for full swing and 400-700 mV for half-swing 010b - (n-1): Values must be monotonic with a non-zero slope. The value of n must be greater than 3 and less than 7. At least two of these must be below the normal operating range of n: 200-400 mV for full-swing and 100-200 mV for half-swing n - 111b" Reserved For a Multi-Function device associated with an Upstream Port, the field in Function 0 is of type RWS, and only Function 0 controls the component`s Link behavior. In all other Functions of that device, this field is of type Reserved. Default value of this field is 000b. Components that support only the 2.5 GT/s speed are permitted to hardwire this bit to 000b. This register is intended for debug, compliance testing purposes only and the system must ensure it is set to the default value during normal operation. 6 5 Reserved 4 Enter Compliance (EC)--R/W. Software is permitted to force a Link to enter Compliance mode at the speed indicated in the Target Link Speed field by setting this bit to 1b in both components on a Link and then initiating a hot reset on the Link. 3:0 19.1.39 Selectable De-emphasis (SD)--R/W. When the Link is operating at 5.0 GT/s speed, this bit selects the level of de-emphasis for an Upstream component. Encodings: 1b =3.5 dB 0b = 6 dB When the Link is operating at 2.5 GT/s speed, the setting of this bit has no effect. Target Link Speed (TLS)--R/W. This field sets an upper limit on Link operational speed by restricting the values advertised by the upstream component in its training sequences. 0001b = 2.5 GT/s Target Link Speed 0010b = 5.0 GT/s and 2.5 GT/s Target Link Speeds All other values reserved. LSTS2--Link Status 2 Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 72h-73h Default Value: 0000h Bit 15:1 0 Datasheet Attribute: Size: RO 16 bits Description Reserved Current De-emphasis Level (CDL)--RO. When the Link is operating at 5 GT/s speed, this bit reflects the level of de-emphasis. Encodings: 0 = -6 dB 1 = -3.5 dB The value in this bit is undefined when the Link is operating at 2.5 GT/s speed. 701 PCI Express* Configuration Registers 19.1.40 MID--Message Signaled Interrupt Identifiers Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 80h-81h Default Value: 9005h Bit 15:8 7:0 19.1.41 Attribute: Size: Description Next Pointer (NEXT)--RO. Indicates the location of the next pointer in the list. Capability ID (CID)--RO. Capabilities ID indicates MSI. MC--Message Signaled Interrupt Message Control Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 82-83h Default Value: 0000h Bit 15:8 7 Attribute: Size: Description Reserved 64-bit Address Capable (C64)--RO. Capable of generating a 32-bit message only. Multiple Message Enable (MME)--R/W. These bits are R/W for software compatibility, but only one message is ever sent by the root port. 3:1 Multiple Message Capable (MMC)--RO. Only one message is required. MSI Enable (MSIE)--R/W. 0 = MSI is disabled. 1 = MSI is enabled and traditional interrupt pins are not used to generate interrupts. Note: CMD.BME (D28:F0/F1/F2/F3/F4/F5/F6/F7:04h:bit 2) must be set for an MSI to be generated. If CMD.BME is cleared, and this bit is set, no interrupts (not even pin based) are generated. MA--Message Signaled Interrupt Message Address Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 84h-87h Default Value: 00000000h Bit 31:2 1:0 702 R/W, RO 16 bits 6:4 0 19.1.42 RO 16 bits Attribute: Size: R/W 32 bits Description Address (ADDR)--R/W. Lower 32 bits of the system specified message address, always DW aligned. Reserved Datasheet PCI Express* Configuration Registers 19.1.43 MD--Message Signaled Interrupt Message Data Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 88h-89h Default Value: 0000h Bit 15:0 19.1.44 Attribute: Size: Description Data (DATA)--R/W. This 16-bit field is programmed by system software if MSI is enabled. Its content is driven onto the lower word (PCI AD[15:0]) during the data phase of the MSI memory write transaction. SVCAP--Subsystem Vendor Capability Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 90h-91h Default Value: A00Dh Attribute: Size: Description 15:8 Next Capability (NEXT)--R/WO. Indicates the location of the next pointer in the list. As this register is RWO, BIOS must write a value to this register, even if it is to re-write the default value. Capability Identifier (CID)--RO. Value of 0Dh indicates this is a PCI bridge subsystem vendor capability. SVID--Subsystem Vendor Identification Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 94h-97h Default Value: 00000000h Bit 31:16 15:0 19.1.46 Attribute: Size: R/WO 32 bits Description Subsystem Identifier (SID)--R/WO. Indicates the subsystem as identified by the vendor. This field is write once and is locked down until a bridge reset occurs (not the PCI bus reset). Subsystem Vendor Identifier (SVID)--R/WO. Indicates the manufacturer of the subsystem. This field is write once and is locked down until a bridge reset occurs (not the PCI bus reset). PMCAP--Power Management Capability Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: A0h-A1h Default Value: 0001h Bit 15:8 7:0 Datasheet R/WO, RO 16 bits Bit 7:0 19.1.45 R/W 16 bits Attribute: Size: RO 16 bits Description Next Capability (NEXT)--RO. Indicates this is the last item in the list. Capability Identifier (CID)--RO. Value of 01h indicates this is a PCI power management capability. 703 PCI Express* Configuration Registers 19.1.47 PMC--PCI Power Management Capabilities Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: A2h-A3h Default Value: C803h Attribute: Size: RO 16 bits Bit Description 15:11 PME_Support (PMES)--RO. Indicates PME# is supported for states D0, D3HOT and D3COLD. The root port does not generate PME#, but reporting that it does is necessary for some legacy operating systems to enable PME# in devices connected behind this root port. 10 D2_Support (D2S)--RO. The D2 state is not supported. 9 D1_Support (D1S)--RO The D1 state is not supported. 8:6 5 Aux_Current (AC)--RO. Reports 375 mA maximum suspend well current required when in the D3COLD state. Device Specific Initialization (DSI)--RO. 1 = Indicates that no device-specific initialization is required. 4 Reserved 3 PME Clock (PMEC)--RO. 1 = Indicates that PCI clock is not required to generate PME#. 2:0 19.1.48 Version (VS)--RO. Indicates support for Revision 1.2 of the PCI Power Management Specification. PMCS--PCI Power Management Control and Status Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: A4h-A7h Default Value: 00000000h Bit 31:24 23 22 21:16 15 Attribute: Size: R/W, RO 32 bits Description Reserved Bus Power / Clock Control Enable (BPCE)--Reserved per PCI Express* Base Specification, Revision 1.0a. B2/B3 Support (B23S)--Reserved per PCI Express* Base Specification, Revision 1.0a. Reserved PME Status (PMES)--RO. 1 = Indicates a PME was received on the downstream link. 14:9 8 Reserved PME Enable (PMEE)--R/W. 1 = Indicates PME is enabled. The root port takes no action on this bit, but it must be R/W for some legacy operating systems to enable PME# on devices connected to this root port. This bit is sticky and resides in the resume well. The reset for this bit is RSMRST# which is not asserted during a warm reset. 704 7:2 Reserved 1:0 Power State (PS)--R/W. This field is used both to determine the current power state of the root port and to set a new power state. The values are: 00 = D0 state 11 = D3HOT state Note: When in the D3HOT state, the controller's configuration space is available, but the I/O and memory spaces are not. Type 1 configuration cycles are also not accepted. Interrupts are not required to be blocked as software will disable interrupts prior to placing the port into D3HOT. If software attempts to write a `10' or `01' to these bits, the write will be ignored. Datasheet PCI Express* Configuration Registers 19.1.49 MPC2--Miscellaneous Port Configuration Register 2 (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: D4h-D7h Default Value: 00000800h Bit 3:2 19.1.50 R/W, RO 32 bits Description 31:5 4 Attribute: Size: Reserved ASPM Control Override Enable (ASPMCOEN)--R/W. 1 = Root port will use the values in the ASPM Control Override registers 0 = Root port will use the ASPM Registers in the Link Control register. Notes: This register allows BIOS to control the root port ASPM settings instead of the OS. ASPM Control Override (ASPMO)--R/W. Provides BIOS control of whether root port should enter L0s or L1 or both. 00 = Disabled 01 = L0s Entry Enabled 10 = L1 Entry Enabled 11 = L0s and L1 Entry Enabled. 1 EOI Forwarding Disable (EOIFD)--R/W. When set, EOI messages are not claimed on the backbone by this port an will not be forwarded across the PCIe link. 0 = Broadcast EOI messages that are sent on the backbone are claimed by this port and forwarded across the PCIe* link. 1 = Broadcast EOI messages are not claimed on the backbone by this port and will not be forwarded across the PCIe Link. 0 L1 Completion Timeout Mode (LICTM)--R/W. 0 = PCI Express Specification Compliant. Completion timeout is disabled during software initiated L1, and enabled during ASPM initiate L1. 1 = Completion timeout is enabled during L1, regardless of how L1 entry was initiated. MPC--Miscellaneous Port Configuration Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: D8h-dBh Default Value: 09110000h Bit Attribute: Size: R/W, RO, R/WO 32 bits Description 31 Power Management SCI Enable (PMCE)--R/W. 0 = SCI generation based on a power management event is disabled. 1 = Enables the root port to generate SCI whenever a power management event is detected. 30 Hot-Plug SCI Enable (HPCE)--R/W. 0 = SCI generation based on a Hot-Plug event is disabled. 1 = Enables the root port to generate SCI whenever a Hot-Plug event is detected. 29 Link Hold Off (LHO)--R/W. 1 = Port will not take any TLP. This is used during loopback mode to fill up the downstream queue. 28 Datasheet Address Translator Enable (ATE)--R/W. This bit is used to enable address translation using the AT bits in this register during loopback mode. 0 = Disable 1 = Enable 27 Reserved 26 Invalid Receive Bus Number Check Enable (IRBNCE)--R/W. When set, the receive transaction layer will signal an error if the bus number of a Memory request does not fall within the range between SCBN and SBBN. If this check is enabled and the request is a memory write, it is treated as an Unsupported Request. If this check is enabled and the request is a non-posted memory read request, the request is considered a Malformed TLP and a fatal error. Messages, I/O, Config, and Completions are never checked for valid bus number. 705 PCI Express* Configuration Registers Bit Description 25 Invalid Receive Range Check Enable (IRRCE)--R/W. When set, the receive transaction layer will treat the TLP as an Unsupported Request error if the address range of a Memory request does not fall outside the range between prefetchable and non-prefetchable base and limit. Messages, I/O, Configuration, and Completions are never checked for valid address ranges. 24 BME Receive Check Enable (BMERCE)--R/W. When set, the receive transaction layer will treat the TLP as an Unsupported Request error if a memory read or write request is received and the Bus Master Enable bit is not set. Messages, I/O, Config, and Completions are never checked for BME. 23 Reserved 22 Detect Override (FORCEDET)--R/W. 0 = Normal operation. Detected output from AFE is sampled for presence detection. 1 = Override mode. Ignores AFE detect output and link training proceeds as if a device were detected. 21 Flow Control During L1 Entry (FCDL1E)--R/W. 0 = No flow control update DLLPs sent during L1 Ack transmission. 1 = Flow control update DLLPs sent during L1 Ack transmission as required to meet the 30 s periodic flow control update. 20:18 Unique Clock Exit Latency (UCEL)--R/W. This value represents the L0s Exit Latency for uniqueclock configurations (LCTL.CCC = 0) (D28:F0/F1/F2/F3/F4/F5/F6/F7:Offset 50h:bit 6). It defaults to 512 ns to less than 1 s, but may be overridden by BIOS. 17:15 Common Clock Exit Latency (CCEL)--R/W. This value represents the L0s Exit Latency for commonclock configurations (LCTL.CCC = 1) (D28:F0/F1/F2/F3/F4/F5/F6/F7:Offset 50h:bit 6). It defaults to 128 ns to less than 256 ns, but may be overridden by BIOS. 14 13:8 7 6:3 706 PCIe Gen2 Speed Disable--R/W. 0 = PCIe supported data rate is defined as set through Supported Link Speed and Target Link Speed settings. 1 = PCIe supported data rate is limited to 2.5 GT/s (Gen1). Supported Link Speed register bits will reflect "0001b" when this bit is set. When this bit is changed, link retrain needs to be performed for the change to be effective. Reserved Port I/OxAPIC Enable (PAE)--R/W. 0 = Hole is disabled. 1 = A range is opened through the bridge for the following memory addresses: Port # Address 1 FEC1_0000h - FEC1_7FFFh 2 FEC1_8000h - FEC1_FFFFh 3 FEC2_0000h - FEC2_7FFFh 4 FEC2_8000h - FEC2_FFFFh 5 FEC3_0000h - FEC3_7FFFh 6 FEC3_8000h - FEC3_FFFFh 7 FEC4_0000h - FEC4_7FFFh 8 FEC4_8000h - FEC4_FFFFh Reserved 2 Bridge Type (BT)--R/WO. This register can be used to modify the Base Class and Header Type fields from the default PCI-to-PCI bridge to a Host Bridge. Having the root port appear as a Host Bridge is useful in some server configurations. 0 = The root port bridge type is a PCI-to-PCI Bridge, Header Sub-Class = 04h, and Header Type = Type 1. 1 = The root port bridge type is a PCI-to-PCI Bridge, Header Sub-Class = 00h, and Header Type = Type 0. 1 Hot-Plug SMI Enable (HPME)--R/W. 0 = SMI generation based on a Hot-Plug event is disabled. 1 = Enables the root port to generate SMI whenever a Hot-Plug event is detected. 0 Power Management SMI Enable (PMME)--R/W. 0 = SMI generation based on a power management event is disabled. 1 = Enables the root port to generate SMI whenever a power management event is detected. Datasheet PCI Express* Configuration Registers 19.1.51 SMSCS--SMI/SCI Status Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: DCh-DFh Default Value: 00000000h Bit Description Power Management SCI Status (PMCS)--R/WC. 1 = PME control logic needs to generate an interrupt, and this interrupt has been routed to generate an SCI. 30 Hot-Plug SCI Status (HPCS)--R/WC. 1 = Hot-Plug controller needs to generate an interrupt, and has this interrupt been routed to generate an SCI. 4 3:2 Reserved Hot-Plug Link Active State Changed SMI Status (HPLAS)--R/WC. 1 = SLSTS.LASC (D28:F0/F1/F2/F3/F4/F5/F6/F7:5Ah, bit 8) transitioned from 0-to-1, and MPC.HPME (D28:F0/F1/F2/F3/F4/F5/F6/F7:D8h, bit 1) is set. When this bit is set, an SMI# will be generated. Reserved 1 Hot-Plug Presence Detect SMI Status (HPPDM)--R/WC. 1 = SLSTS.PDC (D28:F0/F1/F2/F3/F4/F5/F6/F7:5Ah, bit 3) transitioned from 0-to-1, and MPC.HPME (D28:F0/F1/F2/F3/F4/F5/F6/F7:D8h, bit 1) is set. When this bit is set, an SMI# will be generated. 0 Power Management SMI Status (PMMS)--R/WC. 1 = RSTS.PS (D28:F0/F1/F2/F3/F4/F5/F6/F7:60h, bit 16) transitioned from 0-to-1, and MPC.PMME (D28:F0/F1/F2/F3/F4/F5/F6/F7:D8h, bit 1) is set. RPDCGEN--Root Port Dynamic Clock Gating Enable Register (PCI Express--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: E1h Default Value: 00h Bits 7:4 Datasheet R/WC 32 bits 31 29:5 19.1.52 Attribute: Size: Attribute: Size: R/W 8-bits Description Reserved. RO 3 Shared Resource Dynamic Link Clock Gating Enable (SRDLCGEN)--R/W. 0 = Disables dynamic clock gating of the shared resource link clock domain. 1 = Enables dynamic clock gating on the root port shared resource link clock domain. Only the value from Port 1 is used for ports 1-4. Only the value from Port 5 is used for ports 5-8. 2 Shared Resource Dynamic Backbone Clock Gate Enable (SRdBCGEN)--R/W. 0 = Disables dynamic clock gating of the shared resource backbone clock domain. 1 = Enables dynamic clock gating on the root port shared resource backbone clock domain. Only the value from Port 1 is used for ports 1-4. Only the value from Port 5 is used for ports 5-8. 1 Root Port Dynamic Link Clock Gate Enable (RPDLCGEN)--R/W. 0 = Disables dynamic clock gating of the root port link clock domain. 1 = Enables dynamic clock gating on the root port link clock domain. 0 Root Port Dynamic Backbone Clock Gate Enable (RPdBCGEN)--R/W. 0 = Disables dynamic clock gating of the root port backbone clock domain. 1 = Enables dynamic clock gating on the root port backbone clock domain. 707 PCI Express* Configuration Registers 19.1.53 PECR3--PCI Express* Configuration Register 3 (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: ECh-EFh Default Value: 00000000h Bit 31:2 19.1.54 Attribute: Size: Description Reserved 1 Subtractive Decode Compatibility Device ID (SDCDID)--R/W. 0 = This function reports the device Device ID value assigned to the PCI Express Root Ports. See Section 1.3 for the value of the DID Register. 1 = This function reports a Device ID of 244Eh for desktop or 2448h for mobile. If subtractive decode (SDE) is enabled, having this bit as '0' allows the function to present a Device ID that is recognized by the operating system. 0 Subtractive Decode Enable (SDE)--R/W. 0 = Subtractive decode is disabled this function and will only claim transactions positively. 1 = This port will subtractively forward transactions across the PCIe link downstream memory and I/O transactions that are not positively claimed any internal device or bridge. Software must ensure that only one PCH device is enabled for Subtractive decode at a time. PECR4--PCI Express* Configuration Register 4 (PCI Express*--D28:F0/F1/F2/F3/F4/F5) Address Offset: FCh-FFh Default Value: See Below Bit 31:30 Attribute: Size: R/W 32 bits Description USB3 PCIe* Port 2 Mode Strap (USB3_PCIE_PORT2_MODE_STRAP)--RO 00 = Root Port 2 is statically assigned to PCI Express (or GbE) (Default) 01 = Root Port 2 is statically assigned to USB3 10 = Reserved 11 = Reserved Note: Only the value from Port 1 is used. 29:24 Reserved 23:22 SATA Port 3 PCIe* Port 6 Lane 0 Mode Strap (SATAP3_PCIEP6L0_MODE_STRAP)--RO 00 = Statically assigned to SATA Port 3 01 = Statically assigned to PCIe* Port 6 Lane 0 10 = Reserved 11 = Assigned based on the native mode of GPIO37 pin. If the native GPIO37 pin is a 1, then it is assigned to SATA Port 3; otherwise, it is assigned to PCIe* Port 6 Lane 0 Note: Note: Note: 708 R/W 32 bits If this soft strap is set to 11 then GPIO37 native mode is SATA3_PCIEP6L0#; otherwise, the native mode is SATA3GP. This soft strap only has effect if it is allowed by the SATAP3_PCIE6L0_Mode (bits 13:12 in this register). Only the value from Port 1 is used. Datasheet PCI Express* Configuration Registers Bit Description 21:20 SATA Port 2 PCIe* Port 6 Lane 1 Mode Strap (SATAP2_PCIEP6L1_MODE_STRAP)--RO 00 = Statically assigned to SATA Port 2 01 = Statically assigned to PCIe* Port 6 Lane 1 10 = Reserved 11 = Assigned based on the native mode of GPIO36 pin. If the native GPIO36 pin is a `1', then it is assigned to SATA Port 2, else it is assigned to PCIe* Port 6 Lane 1 Note: Note: Note: 19 If this soft strap is set to 11, then GPIO36 native mode is SATA2_PCIE6L1#; otherwise, the native mode is SATA2GP. This soft strap only has effect if it is allowed by the SATAP2_PCIE6L1_Mode (bits 11:10 in this register). Only the value from Port 1 is used. GBE Over PCI Express Port Enable Strap (GBE_PCIE_PEN_STRAP)--RO. 0 = GbE MAC/PHY port communication is not enabled over PCI Express. 1 = The PCI Express port selected by the GBE_PCIEPORTSEL_STRAP (bits 18:16 in this register) will be used for GbE MAC/PHY over PCI Express communication. This strap defines the GbE port. Note: Note: 18:16 GBE PCIe* Port Select Strap (GBE_PCIEPORTSEL_STRAP)--RO. Used to determine which PCIe* port to use for GbE MAC/PHY over PCI Express communication. 000 = Port 3 001 = Port 4 010 = Port 5 Lane 0 011 = Port 5 Lane 1 100 = Port 5 Lane 2 101 = Port 5 Lane 3 110 - 111 = Reserved Note: Note: 15:14 The value of this register, not the soft strap, should be used by GbE and PCI Express. Only the value from Port 1 is used by the lane multiplexing logic. The value of this register, not the soft strap, should be used by GbE and PCI Express. Only the value from Port 1 is used by the lane multiplexing logic. Root Port Configuration Strap (RPC_STRAP)--RO For Port 1: 11 = 1x4 Port 1 (x4), Ports 2-4 (Disabled) 10 = 2x2 Port 1 (x2), Port 3 (x2), Ports 2, 4 (Disabled) 01 = 1x2, 2x1 Port 1 (x2), Port 2 (Disabled), Ports 3, 4 (x1) 00 = 4x1 Ports 1-4 (x1) For Port 5 and Port 6: 11 = 1x4 10 = 1x2 01 = Reserved 00 = 1x1 Note: 13:12 SATA Port 3 PCIe* Port 6 Lane 0 Mode (SATAP3_PCIEP6L0_MODE)--RO 00 = Root Port 1 is statically assigned to SATA Port 3 01 = Root Port 1 is statically assigned to PCIe* Port 6 Lane 0 10 = Assigned based on the SATAP3_PCIEP6L0_MODE_STRAP (bits 23:22 in this register) 11 = Reserved Note: Datasheet Only the value from Port 1 is used for ports 1-4. The values from Port 5 and Port 6 are used for the respective ports. Only the value from Port 1 is used. 709 PCI Express* Configuration Registers Bit 11:10 Description SATA Port 2 PCIe* Port 6 Lane 1 Mode (SATAP2_PCIEP6L1_MODE)--RO 00 = Root Port 1 is statically assigned to SATA Port 2 01 = Root Port 1 is statically assigned to PCIe* Port 6 Lane 1 10 = Assigned based on SATAP2_PCIEP6L1_MODE_STRAP (bits 21:20 in this register) 11 = Reserved Note: 9:2 Reserved 1:0 USB3 PCIe* Port 1 Mode Strap (USB3_PCIE_PORT1_MODE)--RO 00 = Root Port 1 is statically assigned to PCI Express (or GbE) 01 = Root Port 1 is statically assigned to USB3 10 = Reserved 11 = Reserved Note: 19.1.55 Only the value from Port 1 is used. Only the value from Port 1 is used. UES--Uncorrectable Error Status Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 104h-107h Default Value: 00000000000x0xxx0x0x0000000x0000b Attribute: Size: R/WC, RO 32 bits This register maintains its state through a platform reset. It loses its state upon suspend. Bit 31:21 20 Reserved Unsupported Request Error Status (URE)--R/WC. Indicates an unsupported request was received. 19 ECRC Error Status (EE)--RO. ECRC is not supported. 18 Malformed TLP Status (MT)--R/WC. Indicates a malformed TLP was received. 17 Receiver Overflow Status (RO)--R/WC. Indicates a receiver overflow occurred. 16 Unexpected Completion Status (UC)--R/WC. Indicates an unexpected completion was received. 15 Completion Abort Status (CA)--R/WC. Indicates a completer abort was received. 14 Completion Timeout Status (CT)--R/WC. Indicates a completion timed out. This bit is set if Completion Timeout is enabled and a completion is not returned within the time specified by the Completion TImeout Value 13 Flow Control Protocol Error Status (FCPE)--RO. Flow Control Protocol Errors not supported. 12 Poisoned TLP Status (PT)--R/WC. Indicates a poisoned TLP was received. 11:5 4 3:1 0 710 Description Reserved Data Link Protocol Error Status (DLPE)--R/WC. Indicates a data link protocol error occurred. Reserved Training Error Status (TE)--RO. Training Errors not supported. Datasheet PCI Express* Configuration Registers 19.1.56 UEM--Uncorrectable Error Mask Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 108h-10Bh Default Value: 00000000h Attribute: Size: R/WO, RO 32 bits When set, the corresponding error in the UES register is masked, and the logged error will cause no action. When cleared, the corresponding error is enabled. Bit 31:21 20 Reserved Unsupported Request Error Mask (URE)--R/WO. 0 = The corresponding error in the UES register (D28:F0/F1/F2/F3/F4/F5/F6/F7:144) is enabled. 1 = The corresponding error in the UES register (D28:F0/F1/F2/F3/F4/F5/F6/F7:144) is masked. 19 ECRC Error Mask (EE)--RO. ECRC is not supported. 18 Malformed TLP Mask (MT)--R/WO. 0 = The corresponding error in the UES register (D28:F0/F1/F2/F3/F4/F5/F6/F7:144) is enabled. 1 = The corresponding error in the UES register (D28:F0/F1/F2/F3/F4/F5/F6/F7:144) is masked. 17 Receiver Overflow Mask (RO)--R/WO. 0 = The corresponding error in the UES register (D28:F0/F1/F2/F3/F4/F5/F6/F7:144) is enabled. 1 = The corresponding error in the UES register (D28:F0/F1/F2/F3/F4/F5/F6/F7:144) is masked. 16 Unexpected Completion Mask (UC)--R/WO. 0 = The corresponding error in the UES register (D28:F0/F1/F2/F3/F4/F5/F6/F7:144) is enabled. 1 = The corresponding error in the UES register (D28:F0/F1/F2/F3/F4/F5/F6/F7:144) is masked. 15 Completion Abort Mask (CA)--R/WO. 0 = The corresponding error in the UES register (D28:F0/F1/F2/F3/F4/F5/F6/F7:144) is enabled. 1 = The corresponding error in the UES register (D28:F0/F1/F2/F3/F4/F5/F6/F7:144) is masked. 14 Completion Timeout Mask (CT)--R/WO. 0 = The corresponding error in the UES register (D28:F0/F1/F2/F3/F4/F5/F6/F7:144) is enabled. 1 = The corresponding error in the UES register (D28:F0/F1/F2/F3/F4/F5/F6/F7:144) is masked. 13 Flow Control Protocol Error Mask (FCPE)--RO. Flow Control Protocol Errors not supported. 12 Poisoned TLP Mask (PT)--R/WO. 0 = The corresponding error in the UES register (D28:F0/F1/F2/F3/F4/F5/F6/F7:144) is enabled. 1 = The corresponding error in the UES register (D28:F0/F1/F2/F3/F4/F5/F6/F7:144) is masked. 11:5 4 3:1 0 Datasheet Description Reserved Data Link Protocol Error Mask (DLPE)--R/WO. 0 = The corresponding error in the UES register (D28:F0/F1/F2/F3/F4/F5/F6/F7:144) is enabled. 1 = The corresponding error in the UES register (D28:F0/F1/F2/F3/F4/F5/F6/F7:144) is masked. Reserved Training Error Mask (TE)--RO. Training Errors not supported 711 PCI Express* Configuration Registers 19.1.57 UEV--Uncorrectable Error Severity Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 10Ch-10Fh Default Value: 00060011h Bit 31:21 RO, R/W 32 bits Description Reserved 20 Unsupported Request Error Severity (URE)--R/W. 0 = Error considered non-fatal. (Default) 1 = Error is fatal. 19 ECRC Error Severity (EE)--RO. ECRC is not supported. 18 Malformed TLP Severity (MT)--R/W. 0 = Error considered non-fatal. 1 = Error is fatal. (Default) 17 Receiver Overflow Severity (RO)--R/W. 0 = Error considered non-fatal. 1 = Error is fatal. (Default) 16 Reserved 15 Completion Abort Severity (CA)--R/W. 0 = Error considered non-fatal. (Default) 1 = Error is fatal. 14 Reserved 13 Flow Control Protocol Error Severity (FCPE)--RO. Flow Control Protocol Errors not supported. 12 Poisoned TLP Severity (PT)--R/W. 0 = Error considered non-fatal. (Default) 1 = Error is fatal. 11:5 4 3:1 0 712 Attribute: Size: Reserved Data Link Protocol Error Severity (DLPE)--R/W. 0 = Error considered non-fatal. 1 = Error is fatal. (Default) Reserved Training Error Severity (TE)--R/W. TE is not supported. Datasheet PCI Express* Configuration Registers 19.1.58 CES--Correctable Error Status Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 110h-113h Default Value: 00000000h Bit 31:14 13 12 11:9 R/WC 32 bits Description Reserved Advisory Non-Fatal Error Status (ANFES)--R/WC. 0 = Advisory Non-Fatal Error did not occur. 1 = Advisory Non-Fatal Error did occur. Replay Timer Timeout Status (RTT)--R/WC. Indicates the replay timer timed out. Reserved 8 Replay Number Rollover Status (RNR)--R/WC. Indicates the replay number rolled over. 7 Bad DLLP Status (BD)--R/WC. Indicates a bad DLLP was received. 6 5:1 0 19.1.59 Attribute: Size: Bad TLP Status (BT)--R/WC. Indicates a bad TLP was received. Reserved Receiver Error Status (RE)--R/WC. Indicates a receiver error occurred. CEM--Correctable Error Mask Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 114h-117h Default Value: 00002000h Attribute: Size: R/WO 32 bits When set, the corresponding error in the CES register is masked, and the logged error will cause no action. When cleared, the corresponding error is enabled. Bit 31:14 Reserved 13 Advisory Non-Fatal Error Mask (ANFEM)--R/WO. 0 = Does not mask Advisory Non-Fatal errors. 1 = Masks Advisory Non-Fatal errors from (a) signaling ERR_COR to the device control register and (b) updating the Uncorrectable Error Status register. This register is set by default to enable compatibility with software that does not comprehend RoleBased Error Reporting. Note: The correctable error detected bit in device status register is set whenever the Advisory Non-Fatal error is detected, independent of this mask bit. 12 Replay Timer Timeout Mask (RTT)--R/WO. Mask for replay timer timeout. 11:9 Reserved 8 Replay Number Rollover Mask (RNR)--R/WO. Mask for replay number rollover. 7 Bad DLLP Mask (BD)--R/WO. Mask for bad DLLP reception. 6 Bad TLP Mask (BT)--R/WO. Mask for bad TLP reception. 5:1 0 Datasheet Description Reserved Receiver Error Mask (RE)--R/WO. Mask for receiver errors. 713 PCI Express* Configuration Registers 19.1.60 AECC--Advanced Error Capabilities and Control Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 118h-11Bh Default Value: 00000000h Bit 31:9 Reserved ECRC Check Enable (ECE)--RO. ECRC is not supported. 7 ECRC Check Capable (ECC)--RO. ECRC is not supported. 6 ECRC Generation Enable (EGE)--RO. ECRC is not supported. 5 ECRC Generation Capable (EGC)--RO. ECRC is not supported. First Error Pointer (FEP)--RO. Identifies the bit position of the last error reported in the Uncorrectable Error Status Register. RES--Root Error Status Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 130h-133h Default Value: 00000000h Bit 31:27 26:7 714 RO 32 bits Description 8 4:0 19.1.61 Attribute: Size: Attribute: Size: R/WC, RO 32 bits Description Advanced Error Interrupt Message Number (AEMN)--RO. There is only one error interrupt allocated. Reserved 6 Fatal Error Messages Received (FEMR)--RO. Set when one or more Fatal Uncorrectable Error Messages have been received. 5 Non-Fatal Error Messages Received (NFEMR)--RO. Set when one or more Non-Fatal Uncorrectable error messages have been received 4 First Uncorrectable Fatal (FUF)--RO. Set when the first Uncorrectable Error message received is for a fatal error. 3 Multiple ERR_FATAL/NONFATAL Received (MENR)--RO. For the PCH, only one error will be captured. 2 ERR_FATAL/NONFATAL Received (ENR)--R/WC. 0 = No error message received. 1 = Either a fatal or a non-fatal error message is received. 1 Multiple ERR_COR Received (MCR)--RO. For the PCH, only one error will be captured. 0 ERR_COR Received (CR)--R/WC. 0 = No error message received. 1 = A correctable error message is received. Datasheet PCI Express* Configuration Registers 19.1.62 PECR2--PCI Express* Configuration Register 2 (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 320-323h Default Value: 0004B05Bh Bit 31:20 21 20:0 19.1.63 Attribute: Size: Description Reserved PECR2 Field 1--R/W. BIOS must set this bit to 1b. Reserved PEETM--PCI Express* Extended Test Mode Register (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 324h-327h Default Value: See Description Bit 31:5 4 Attribute: Size: RO 32 bits Description Reserved Lane Reversal (LR)--RO. This register reads the setting of the PCIELR1 soft strap for port 1 and the PCIELR2 soft strap for port 5. 0 = No Lane reversal (default). 1 = PCI Express lanes 0-3 (register in port 1) or lanes 4-7 (register in port 5) are reversed. Notes: 1. The port configuration straps must be set such that Port 1 or Port 5 is configured as a x4 port using lanes 0-3, or 4-7 when Lane Reversal is enabled. x2 lane reversal is not supported. 2. This register is only valid on port 1 (for ports 1-4) or port 5 (for ports 5-8). 3 Reserved 2 Scrambler Bypass Mode (BAU)--R/W. 0 = Normal operation. Scrambler and descrambler are used. 1 = Bypasses the data scrambler in the transmit direction and the data de-scrambler in the receive direction. Note: This functionality intended for debug/testing only. Note: If bypassing scrambler with the PCH root port 1 in x4 configuration, each PCH root port must have this bit set. 1:0 19.1.64 R/W 32 bits Reserved PEC1--PCI Express* Configuration Register 1 (PCI Express*--D28:F0/F1/F2/F3/F4/F5/F6/F7) Address Offset: 330h-333h Default Value: 28000016h Bit 31:8 7:0 Attribute: Size: RO, R/W 32 bits Description Reserved PEC1 Field 1--R/W. BIOS must program this field to 40h. Datasheet 715 High Precision Event Timer Registers 20 High Precision Event Timer Registers The timer registers are memory-mapped in a non-indexed scheme. This allows the processor to directly access each register without having to use an index register. The timer register space is 1024 bytes. The registers are generally aligned on 64-bit boundaries to simplify implementation with IA64 processors. There are four possible memory address ranges beginning at 1) FED0_0000h, 2) FED0_1000h, 3) FED0_2000h, 4) FED0_3000h. The choice of address range will be selected by configuration bits in the High Precision Timer Configuration Register (Chipset Config Registers:Offset 3404h). Behavioral Rules: 1. Software must not attempt to read or write across register boundaries. For example, a 32-bit access should be to offset x0h, x4h, x8h, or xCh. 32-bit accesses should not be to 01h, 02h, 03h, 05h, 06h, 07h, 09h, 0Ah, 0Bh, 0Dh, 0Eh, or 0Fh. Any accesses to these offsets will result in an unexpected behavior, and may result in a master abort. However, these accesses should not result in system hangs. 64bit accesses can only be to x0h and must not cross 64-bit boundaries. 2. Software should not write to Read Only registers. 3. Software should not expect any particular or consistent value when reading reserved registers or bits. 20.1 Memory Mapped Registers Table 20-1. Memory-Mapped Register Address Map (Sheet 1 of 2) 716 Offset Mnemonic 000h-007h GCAP_ID 008h-00Fh -- 010h-017h GEN_CONF 018h-01Fh -- 020h-027h GINTR_STA 028h-0EFh -- 0F0h-0F7h MAIN_CNT 0F8h-0FFh -- 100h-107h TIM0_CONF 108h-10Fh TIM0_COMP 110h-11Fh -- Register General Capabilities and Identification Reserved General Configuration Reserved General Interrupt Status Reserved Main Counter Value Reserved Default Attribute 0429B17F8086 A201h RO -- -- 000000000000 0000h R/W -- -- 000000000000 0000h R/WC -- -- N/A R/W -- -- Timer 0 Configuration and Capabilities N/A R/W, RO Timer 0 Comparator Value N/A R/W -- -- Reserved 120h-127h TIM1_CONF Timer 1 Configuration and Capabilities N/A R/W, RO 128h-12Fh TIM1_COMP Timer 1 Comparator Value N/A R/W 130h-13Fh -- -- -- Reserved Datasheet High Precision Event Timer Registers Table 20-1. Memory-Mapped Register Address Map (Sheet 2 of 2) Offset Mnemonic Register Default Attribute 140h-147h TIM2_CONF Timer 2 Configuration and Capabilities N/A R/W, RO 148h-14Fh TIM2_COMP Timer 2 Comparator Value N/A R/W 150h-15Fh -- 160h-167h TIM3_CONG Reserved Timer 3 Configuration and Capabilities -- -- N/A R/W, RO 168h-16Fh TIM3_COMP Timer 3 Comparator Value N/A R/W 180h-187h TIM4_CONG Timer 4 Configuration and Capabilities N/A R/W, RO 188h-18Fh TIM4_COMP Timer 4 Comparator Value N/A R/W 190h-19Fh -- -- -- 1A0h-1A7h TIM5_CONG Timer 5 Configuration and Capabilities N/A R/W, RO 1A8h-1AFh TIM5_COMP Timer 5 Comparator Value N/A R/W 1B0h-1BFh -- 1C0h-1C7h TIM6_CONG Reserved -- -- Timer 6 Configuration and Capabilities Reserved N/A R/W, RO Timer 6 Comparator Value N/A R/W -- -- 1C8h-1CFh TIM6_COMP 1D0h-1DFh -- 1E0h-1E7h TIM7_CONG Timer 7 Configuration and Capabilities N/A R/W, RO 1E8h-1EFh TIM7_COMP Timer 7 Comparator Value N/A R/W Reserved 1F0h-19Fh -- Reserved -- -- 200h-3FFh -- Reserved -- -- Notes: 1. Reads to reserved registers or bits will return a value of 0. 2. Software must not attempt locks to the memory-mapped I/O ranges for High Precision Event Timers. If attempted, the lock is not honored, which means potential deadlock conditions may occur. 20.1.1 GCAP_ID--General Capabilities and Identification Register Address Offset: 00h Default Value: 0429B17F8086A201h RO 64 bits Bit Description 63:32 Main Counter Tick Period (COUNTER_CLK_PER_CAP)--RO. This field indicates the period at which the counter increments in femptoseconds (10^-15 seconds). This will return 0429B17Fh when read. This indicates a period of 69841279 fs (69.841279 ns). 31:16 Vendor ID Capability (VENDOR_ID_CAP)--RO. This is a 16-bit value assigned to Intel. 15 Legacy Replacement Rout Capable (LEG_RT_CAP)--RO. Hardwired to 1. Legacy Replacement Interrupt Rout option is supported. 14 Reserved. This bit returns 0 when read. 13 12:8 7:0 Datasheet Attribute: Size: Counter Size Capability (COUNT_SIZE_CAP)--RO. Hardwired to 1. Counter is 64-bit wide. Number of Timer Capability (NUM_TIM_CAP)--RO. This field indicates the number of timers in this block. 07h = Eight timers. Revision Identification (REV_ID)--RO. This indicates which revision of the function is implemented. Default value will be 01h. 717 High Precision Event Timer Registers 20.1.2 GEN_CONF--General Configuration Register Address Offset: 010h Default Value: 00000000 00000000h Bit 63:2 R/W 64 bits Description Reserved. These bits return 0 when read. 1 Legacy Replacement Rout (LEG_RT_CNF)--R/W. If the ENABLE_CNF bit and the LEG_RT_CNF bit are both set, then the interrupts will be routed as follows: * Timer 0 is routed to IRQ0 in 8259 or IRQ2 in the I/O APIC * Timer 1 is routed to IRQ8 in 8259 or IRQ8 in the I/O APIC * Timer 2-n is routed as per the routing in the timer n config registers. * If the Legacy Replacement Rout bit is set, the individual routing bits for Timers 0 and 1 (APIC) will have no impact. * If the Legacy Replacement Rout bit is not set, the individual routing bits for each of the timers are used. * This bit will default to 0. BIOS can set it to 1 to enable the legacy replacement routing, or 0 to disable the legacy replacement routing. 0 Overall Enable (ENABLE_CNF)--R/W. This bit must be set to enable any of the timers to generate interrupts. If this bit is 0, then the main counter will halt (will not increment) and no interrupts will be caused by any of these timers. For level-triggered interrupts, if an interrupt is pending when the ENABLE_CNF bit is changed from 1 to 0, the interrupt status indications (in the various Txx_INT_STS bits) will not be cleared. Software must write to the Txx_INT_STS bits to clear the interrupts. Note: 20.1.3 Attribute: Size: This bit will default to 0. BIOS can set it to 1 or 0. GINTR_STA--General Interrupt Status Register Address Offset: 020h Default Value: 00000000 00000000h Attribute: Size: R/WC 64 bits . Bit 63:8 7 718 Description Reserved. These bits will return 0 when read. Timer 7 Interrupt Active (T07_INT_STS)--R/WC. Same functionality as Timer 0. 6 Timer 6 Interrupt Active (T06_INT_STS)--R/WC. Same functionality as Timer 0. 5 Timer 5 Interrupt Active (T05_INT_STS)--R/WC. Same functionality as Timer 0. 4 Timer 4 Interrupt Active (T04_INT_STS)--R/WC. Same functionality as Timer 0. 3 Timer 3 Interrupt Active (T03_INT_STS)--R/WC. Same functionality as Timer 0. 2 Timer 2 Interrupt Active (T02_INT_STS)--R/WC. Same functionality as Timer 0. 1 Timer 1 Interrupt Active (T01_INT_STS)--R/WC. Same functionality as Timer 0. 0 Timer 0 Interrupt Active (T00_INT_STS)--R/WC. The functionality of this bit depends on whether the edge or level-triggered mode is used for this timer. (default = 0) If set to level-triggered mode: This bit will be set by hardware if the corresponding timer interrupt is active. Once the bit is set, it can be cleared by software writing a 1 to the same bit position. Writes of 0 to this bit will have no effect. If set to edge-triggered mode: This bit should be ignored by software. Software should always write 0 to this bit. Note: Defaults to 0. In edge triggered mode, this bit will always read as 0 and writes will have no effect. Datasheet High Precision Event Timer Registers 20.1.4 MAIN_CNT--Main Counter Value Register Address Offset: 0F0h Default Value: N/A Attribute: Size: R/W 64 bits . Bit 63:0 20.1.5 Description Counter Value (COUNTER_VAL[63:0])--R/W. Reads return the current value of the counter. Writes load the new value to the counter. Notes: 1. Writes to this register should only be done while the counter is halted. 2. Reads to this register return the current value of the main counter. 3. 32-bit counters will always return 0 for the upper 32-bits of this register. 4. If 32-bit software attempts to read a 64-bit counter, it should first halt the counter. Since this delays the interrupts for all of the timers, this should be done only if the consequences are understood. It is strongly recommended that 32-bit software only operate the timer in 32-bit mode. 5. Reads to this register are monotonic. No two consecutive reads return the same value. The second of two reads always returns a larger value (unless the timer has rolled over to 0). TIMn_CONF--Timer n Configuration and Capabilities Register Address Offset: Timer Timer Timer Timer Timer Timer Timer Timer Default Value: N/A Note: 0: 1: 2: 3: 4: 5: 6: 7: 100-107h 120-127h 140-147h 160-167h 180-187h 1A0-1A7h 1C0-1C7h 1E0-1E7h RO, R/W Size: 64 bit The letter n can be 0, 1, 2, 3, 4, 5, 6, or 7 referring to Timer 0, 1, 2, 3, 4, 5, 6, or 7. Bit Datasheet Attribute: Description 63:56 Reserved. These bits will return 0 when read. 55:52, 44,43 Timer Interrupt Rout Capability (TIMERn_INT_ROUT_CAP)--RO. Timer 0, 1:Bits 52, 53, 54, and 55 in this field (corresponding to IRQ 20, 21, 22, and 23) have a value of 1. Writes will have no effect. Timer 2:Bits 43, 52, 53, 54, and 55 in this field (corresponding to IRQ 11, 20, 21, 22, and 23) have a value of 1. Writes will have no effect. Timer 3:Bits 44, 52, 53, 54, and 55 in this field (corresponding to IRQ 11, 20, 21, 22, and 23) have a value of 1. Writes will have no effect. Timer 4, 5, 6, 7:This field is always 0 as interrupts from these timers can only be delivered using direct processor interrupt messages. Note: If IRQ 11 is used for HPET #2, software should ensure IRQ 11 is not shared with any other devices to ensure the proper operation of HPET #2. Note: If IRQ 12 is used for HPET #3, software should ensure IRQ 12 is not shared with any other devices to ensure the proper operation of HPET #3. 51:45, 42:16 Reserved. These bits return 0 when read. 15 Timer n Processor Message Interrupt Delivery (Tn_PROCMSG_INT_DEL_CAP)--RO. This bit is always read as `1', since the PCH HPET implementation supports the direct processor interrupt delivery. 14 Timer n Processor Message Interrupt Enable (Tn_PROCMSG_EN_CNF)--R/W / RO. If the Tn_PROCMSG_INT_DEL_CAP bit is set for this timer, then the software can set the Tn_PROCMSG_EN_CNF bit to force the interrupts to be delivered directly as processor messages, rather than using the 8259 or I/O (x) APIC. In this case, the Tn_INT_ROUT_CNF field in this register will be ignored. The Tn_PROCMSG_ROUT register will be used instead. Timer 0, 1, 2, 3 Specific: This bit is a read/write bit. Timer 4, 5, 6, 7 Specific: This bit is always Read Only `1' as interrupt from these timers can only be delivered using direct processor interrupt messages. 719 High Precision Event Timer Registers Bit Description 13:9 Timer n Interrupt Rout (Tn_INT_ROUT_CNF)--R/W / RO. This 5-bit field indicates the routing for the interrupt to the 8259 or I/O (x) APIC. Software writes to this field to select which interrupt in the 8259 or I/O (x) will be used for this timer's interrupt. If the value is not supported by this particular timer, then the value read back will not match what is written. The software must only write valid values. Timer 4, 5, 6, 7: This field is Read Only and reads will return 0. Notes: 1. If the interrupt is handled using the 8259, only interrupts 0-15 are applicable and valid. Software must not program any value other than 0-15 in this field. 2. If the Legacy Replacement Rout bit is set, then Timers 0 and 1 will have a different routing, and this bit field has no effect for those two timers. 3. Timer 0,1: Software is responsible to make sure it programs a valid value (20, 21, 22, or 23) for this field. The PCH logic does not check the validity of the value written. 4. Timer 2: Software is responsible to make sure it programs a valid value (11, 20, 21, 22, or 23) for this field. The PCH logic does not check the validity of the value written. 5. Timer 3: Software is responsible to make sure it programs a valid value (12, 20, 21, 22, or 23) for this field. The PCH logic does not check the validity of the value written. 6. Timers 4, 5, 6, 7: This field is always Read Only 0 as interrupts from these timers can only be delivered using direct processor interrupt messages. 8 Timer n 32-bit Mode (TIMERn_32MODE_CNF)--R/W or RO. Software can set this bit to force a 64-bit timer to behave as a 32-bit timer. Timer 0:Bit is read/write (default to 0). 0 = 64 bit; 1 = 32 bit Timers 1, 2, 3, 4, 5, 6, 7:Hardwired to 0. Writes have no effect (since these seven timers are 32bits). Note: When this bit is set to 1, the hardware counter will do a 32-bit operation on comparator match and rollovers; thus, the upper 32-bit of the Timer 0 Comparator Value register is ignored. The upper 32-bit of the main counter is not involved in any rollover from lower 32-bit of the main counter and becomes all zeros. 7 Reserved. This bit returns 0 when read. 6 Timer n Value Set (TIMERn_VAL_SET_CNF)--R/W. Software uses this bit only for Timer 0 if it has been set to periodic mode. By writing this bit to a 1, the software is then allowed to directly set the timer's accumulator. Software does not have to write this bit back to 1 (it automatically clears). Software should not write a 1 to this bit position if the timer is set to non-periodic mode. Note: This bit will return 0 when read. Writes will only have an effect for Timer 0 if it is set to periodic mode. Writes will have no effect for Timers 1, 2, 3, 4, 5, 6, 7. 5 Timer n Size (TIMERn_SIZE_CAP)--RO. This read only field indicates the size of the timer. Timer 0:Value is 1 (64-bits). Timers 1, 2, 3, 4, 5, 6, 7: Value is 0 (32-bits). 4 Periodic Interrupt Capable (TIMERn_PER_INT_CAP)--RO. If this bit is 1, the hardware supports a periodic mode for this timer's interrupt. Timer 0: Hardwired to 1 (supports the periodic interrupt). Timers 1, 2, 3, 4, 5, 6, 7: Hardwired to 0 (does not support periodic interrupt). 3 Timer n Type (TIMERn_TYPE_CNF)--R/W or RO. Timer 0:Bit is read/write. 0 = Disable timer to generate periodic interrupt; 1 = Enable timer to generate a periodic interrupt. Timers 1, 2, 3, 4, 5, 6, 7: Hardwired to 0. Writes have no affect. 2 Timer n Interrupt Enable (TIMERn_INT_ENB_CNF)--R/W. This bit must be set to enable timer n to cause an interrupt when it times out. 0 = Disable (Default). The timer can still count and generate appropriate status bits, but will not cause an interrupt. 1 = Enable. 1 Timer Interrupt Type (TIMERn_INT_TYPE_CNF)--R/W. 0 = The timer interrupt is edge triggered. This means that an edge-type interrupt is generated. If another interrupt occurs, another edge will be generated. 1 = The timer interrupt is level triggered. This means that a level-triggered interrupt is generated. The interrupt will be held active until it is cleared by writing to the bit in the General Interrupt Status Register. If another interrupt occurs before the interrupt is cleared, the interrupt will remain active. Timer 4, 5, 6, 7: This bit is Read Only, and will return 0 when read 0 Note: 720 Reserved. These bits will return 0 when read. Reads or writes to unimplemented timers should not be attempted. Read from any unimplemented registers will return an undetermined value. Datasheet High Precision Event Timer Registers 20.1.6 TIMn_COMP--Timer n Comparator Value Register Address Offset: Timer Timer Timer Timer Timer Timer Timer Timer Default Value: N/A 0: 1: 2: 3: 4: 5: 6: 7: 108h-10Fh, 128h-12Fh, 148h-14Fh, 168h-16Fh, 188h-18Fh, 1A8h-1AFh, 1C8h-1CFh, 1E8h-1EFh Attribute: R/W Size: 64 bit Bit Description 63:0 Timer Compare Value--R/W. Reads to this register return the current value of the comparator If Timer n is configured to non-periodic mode: Writes to this register load the value against which the main counter should be compared for this timer. * When the main counter equals the value last written to this register, the corresponding interrupt can be generated (if so enabled). * The value in this register does not change based on the interrupt being generated. If Timer 0 is configured to periodic mode: * When the main counter equals the value last written to this register, the corresponding interrupt can be generated (if so enabled). * After the main counter equals the value in this register, the value in this register is increased by the value last written to the register. For example, if the value written to the register is 00000123h, then 1. An interrupt will be generated when the main counter reaches 00000123h. 2. The value in this register will then be adjusted by the hardware to 00000246h. 3. Another interrupt will be generated when the main counter reaches 00000246h 4. The value in this register will then be adjusted by the hardware to 00000369h * As each periodic interrupt occurs, the value in this register will increment. When the incremented value is greater than the maximum value possible for this register (FFFFFFFFh for a 32-bit timer or FFFFFFFFFFFFFFFFh for a 64-bit timer), the value will wrap around through 0. For example, if the current value in a 32-bit timer is FFFF0000h and the last value written to this register is 20000h, then after the next interrupt the value will change to 00010000h Default value for each timer is all 1s for the bits that are implemented. For example, a 32-bit timer has a default value of 00000000FFFFFFFFh. A 64-bit timer has a default value of FFFFFFFFFFFFFFFFh. Datasheet 721 High Precision Event Timer Registers 20.1.7 TIMERn_PROCMSG_ROUT--Timer n Processor Message Interrupt Rout Register Address Offset: Timer Timer Timer Timer Timer Timer Timer Timer Default Value: N/A Note: 0: 1: 2: 3: 4: 5: 6: 7: 110-117h, 130-137h, 150-157h, 170-177h, 190-197h, 1B0-1B7h, 1D0-1D7h, 1F0-1F7h, Attribute: R/W Size: 64 bit The letter n can be 0, 1, 2, 3, 4, 5, 6, or 7 referring to Timer 0, 1, 2, 3, 4, 5, 6, or 7. Software can access the various bytes in this register using 32-bit or 64-bit accesses. 32-bit accesses can be done to offset 1x0h or 1x4h. 64-bit accesses can be done to 1x0h. 32-bit accesses must not be done to offsets 1x1h, 1x2h, 1x3h, 1x5h, 1x6h, or 1x7h. Bit Description 63:32 Tn_PROCMSG_INT_ADDR--R/W. Software sets this 32-bit field to indicate the location that the direct processor interrupt message should be written. 31:0 Tn_PROCMSG_INT_VAL--R/W. Software sets this 32-bit field to indicate that value that is written during the direct processor interrupt message. 722 Datasheet Serial Peripheral Interface (SPI) 21 Serial Peripheral Interface (SPI) The Serial Peripheral Interface resides in memory mapped space. This function contains registers that allow for the setup and programming of devices that reside on the SPI interface. Note: All registers in this function (including memory-mapped registers) must be addressable in byte, word, and DWord quantities. The software must always make register accesses on natural boundaries (that is, DWord accesses must be on DWord boundaries; word accesses on word boundaries, and so on) In addition, the memory-mapped register space must not be accessed with the LOCK semantic exclusive-access mechanism. If software attempts exclusive-access mechanisms to the SPI memory-mapped space, the results are undefined. 21.1 Serial Peripheral Interface Memory Mapped Configuration Registers The SPI Host Interface registers are memory-mapped in the RCRB (Root Complex Register Block) Chipset Register Space with a base address (SPIBAR) of 3800h and are located within the range of 3800h to 39FFh. The address for RCRB are in the RCBA Register (see Section 12.1.40). The individual registers are then accessible at SPIBAR + Offset as indicated in the following table. These memory mapped registers must be accessed in byte, word, or DWord quantities. Table 21-1. Serial Peripheral Interface (SPI) Register Address Map (SPI Memory Mapped Configuration Registers) (Sheet 1 of 2) SPIBAR + Offset Datasheet Mnemonic Register Name 00h-03h BFPR BIOS Flash Primary Region 04h-05h HSFS Hardware Sequencing Flash Status 06h-07h HSFC 08h-0Bh FADDR Hardware Sequencing Flash Control Default 00000000h 0000h 0000h Flash Address 00000000h 0Ch-0Fh -- Reserved 00000000h 10h-13h FDATA0 Flash Data 0 00000000h 14h-4Fh FDATAN Flash Data N 00000000h 50h-53h FRAP Flash Region Access Permissions 00000202h 54h-57h FREG0 Flash Region 0 00000000h 58h-5Bh FREG1 Flash Region 1 00000000h 5Ch-5Fh FREG2 Flash Region 2 00000000h 60h-63h FREG3 Flash Region 3 00000000h 64h-67h FREG4 Flash Region 4 00000000h 67h-73h -- 74h-77h PR0 Reserved for Future Flash Regions Flash Protected Range 0 00000000h 723 Serial Peripheral Interface (SPI) Table 21-1. Serial Peripheral Interface (SPI) Register Address Map (SPI Memory Mapped Configuration Registers) (Sheet 2 of 2) 21.1.1 SPIBAR + Offset Mnemonic 78h-7Bh PR1 Flash Protected Range 1 00000000h 7Ch-7Fh PR2 Flash Protected Range 2 00000000h 80h-83h PR3 Flash Protected Range 3 00000000h 84h-87h PR4 Flash Protected Range 4 00000000h 88h-8Fh -- Register Name Reserved -- 90h SSFS Software Sequencing Flash Status 00h 91h-93h SSFC Software Sequencing Flash Control 0000h 94h-95h PREOP Prefix Opcode Configuration 0000h 96h-97h OPTYPE Opcode Type Configuration 0000h 98h-9Fh OPMENU Opcode Menu Configuration 000000000000000 0h A0h BBAR BIOS Base Address Configuration FDOC Flash Descriptor Observability Control 00000000h B4h-B7h FDOD Flash Descriptor Observability Data 00000000h B8h-C3h -- C0h-C3h AFC Reserved -- Additional Flash Control 00000000h C4h-C7h LVSCC Host Lower Vendor Specific Component Capabilities 00000000h C8h-C11h UVSCC Host Upper Vendor Specific Component Capabilities 00000000h D0h-D3h FPB Flash Partition Boundary 00000000h F0h-F3h SRDL Soft Reset Data Lock 00000000h F4h-F7h SRDC Soft Reset Data Control 00000000h F8h-FBh SRD Soft Reset Data 00000000h BFPR -BIOS Flash Primary Region Register (SPI Memory Mapped Configuration Registers) Attribute: Size: RO 32 bits This register is only applicable when SPI device is in descriptor mode. Bit 31:29 Description Reserved 28:16 BIOS Flash Primary Region Limit (PRL)--RO. This specifies address bits 24:12 for the Primary Region Limit. The value in this register loaded from the contents in the Flash Descriptor.FLREG1.Region Limit 15:13 Reserved 12:0 724 00000000h B0h-B3h Memory Address: SPIBAR + 00h Default Value: 00000000h Note: Default BIOS Flash Primary Region Base (PRB)--RO. This specifies address bits 24:12 for the Primary Region Base The value in this register is loaded from the contents in the Flash Descriptor.FLREG1.Region Base Datasheet Serial Peripheral Interface (SPI) 21.1.2 HSFS--Hardware Sequencing Flash Status Register (SPI Memory Mapped Configuration Registers) Memory Address: SPIBAR + 04h Default Value: 0000h Bit RO, R/WC, R/W 16 bits Description 15 Flash Configuration Lock-Down (FLOCKDN)--R/W/L. When set to 1, those Flash Program Registers that are locked down by this FLOCKDN bit cannot be written. Once set to 1, this bit can only be cleared by a hardware reset due to a global reset or host partition reset in an Intel ME enabled system. 14 Flash Descriptor Valid (FDV)--RO. This bit is set to a 1 if the Flash Controller read the correct Flash Descriptor Signature. If the Flash Descriptor Valid bit is not 1, software cannot use the Hardware Sequencing registers, but must use the software sequencing registers. Any attempt to use the Hardware Sequencing registers will result in the FCERR bit being set. 13 Flash Descriptor Override Pin Strap Status (FDOPSS)--RO. This bit indicates the condition of the Flash Descriptor Security Override / Intel ME Debug Mode pin strap. 0 = The Flash Descriptor Security Override / Intel ME Debug Mode strap is set using external pullup on HDA_SDO 1 = No override 12:6 Datasheet Attribute: Size: Reserved 5 SPI Cycle In Progress (SCIP)--RO. Hardware sets this bit when software sets the Flash Cycle Go (FGO) bit in the Hardware Sequencing Flash Control register. This bit remains set until the cycle completes on the SPI interface. Hardware automatically sets and clears this bit so that software can determine when read data is valid and/or when it is safe to begin programming the next command. Software must only program the next command when this bit is 0. Note: This field is only applicable when in Descriptor mode and Hardware sequencing is being used. 4:3 Block/Sector Erase Size (BERASE)--RO. This field identifies the erasable sector size for all Flash components. Valid Bit Settings: 00 = 256 Byte 01 = 4 K Byte 10 = 8 K Byte 11 = 64 K Byte If the FLA is less than FPBA, then this field reflects the value in the LVSCC.LBES register. If the FLA is greater or equal to FPBA, then this field reflects the value in the UVSCC.UBES register. Note: This field is only applicable when in Descriptor mode and Hardware sequencing is being used. 2 Access Error Log (AEL)--R/W/C. Hardware sets this bit to a 1 when an attempt was made to access the BIOS region using the direct access method or an access to the BIOS Program Registers that violated the security restrictions. This bit is simply a log of an access security violation. This bit is cleared by software writing a 1. Note: This field is only applicable when in Descriptor mode and Hardware sequencing is being used. 1 Flash Cycle Error (FCERR)--R/W/C. Hardware sets this bit to 1 when an program register access is blocked to the FLASH due to one of the protection policies or when any of the programmed cycle registers is written while a programmed access is already in progress. This bit remains asserted until cleared by software writing a 1 or until hardware reset occurs due to a global reset or host partition reset in an Intel ME enabled system. Software must clear this bit before setting the FLASH Cycle GO bit in this register. Note: This field is only applicable when in Descriptor mode and Hardware sequencing is being used. 0 Flash Cycle Done (FDONE)--R/W/C. The PCH sets this bit to 1 when the SPI Cycle completes after software previously set the FGO bit. This bit remains asserted until cleared by software writing a 1 or hardware reset due to a global reset or host partition reset in an Intel ME enabled system. When this bit is set and the SPI SMI# Enable bit is set, an internal signal is asserted to the SMI# generation block. Software must make sure this bit is cleared prior to enabling the SPI SMI# assertion for a new programmed access. Note: This field is only applicable when in Descriptor mode and Hardware sequencing is being used. 725 Serial Peripheral Interface (SPI) 21.1.3 HSFC--Hardware Sequencing Flash Control Register (SPI Memory Mapped Configuration Registers) Memory Address: SPIBAR + 06h Default Value: 0000h Note: Description 15 Flash SPI SMI# Enable (FSMIE)--R/W. When set to 1, the SPI asserts an SMI# request whenever the Flash Cycle Done bit is 1. 14 Reserved 13:8 Flash Data Byte Count (FdBC)--R/W. This field specifies the number of bytes to shift in or out during the data portion of the SPI cycle. The contents of this register are 0s based with 0b representing 1 byte and 111111b representing 64 bytes. The number of bytes transferred is the value of this field plus 1. This field is ignored for the Block Erase command. 7:3 Reserved 2:1 FLASH Cycle (FCYCLE)--R/W. This field defines the Flash SPI cycle type generated to the FLASH when the FGO bit is set as defined below: 00 = Read (1 up to 64 bytes by setting FdBC) 01 = Reserved 10 = Write (1 up to 64 bytes by setting FdBC) 11 = Block Erase 0 Flash Cycle Go (FGO)--R/W/S. A write to this register with a 1 in this bit initiates a request to the Flash SPI Arbiter to start a cycle. This register is cleared by hardware when the cycle is granted by the SPI arbiter to run the cycle on the SPI bus. When the cycle is complete, the FDONE bit is set. Software is forbidden to write to any register in the HSFLCTL register between the FGO bit getting set and the FDONE bit being cleared. Any attempt to violate this rule will be ignored by hardware. Hardware allows other bits in this register to be programmed for the same transaction when writing this bit to 1. This saves an additional memory write. This bit always returns 0 on reads. FADDR--Flash Address Register (SPI Memory Mapped Configuration Registers) Memory Address: SPIBAR + 08h Default Value: 00000000h Bit 31:25 24:0 726 R/W, R/WS 16 bits This register is only applicable when SPI device is in descriptor mode. Bit 21.1.4 Attribute: Size: Attribute: Size: R/W 32 bits Description Reserved Flash Linear Address (FLA)--R/W. The FLA is the starting byte linear address of a SPI Read or Write cycle or an address within a Block for the Block Erase command. The Flash Linear Address must fall within a region for which BIOS has access permissions. Hardware must convert the FLA into a Flash Physical Address (FPA) before running this cycle on the SPI bus. Datasheet Serial Peripheral Interface (SPI) 21.1.5 FDATA0--Flash Data 0 Register (SPI Memory Mapped Configuration Registers) Memory Address: SPIBAR + 10h Default Value: 00000000h 21.1.6 Attribute: Size: Bit Description 31:0 Flash Data 0 (FD0)--R/W. This field is shifted out as the SPI Data on the Master-Out Slave-In Data pin during the data portion of the SPI cycle. This register also shifts in the data from the Master-In Slave-Out pin into this register during the data portion of the SPI cycle. The data is always shifted starting with the least significant byte, msb to lsb, followed by the next least significant byte, msb to lsb, and so on. Specifically, the shift order on SPI in terms of bits within this register is: 7-6-5-4-3-2-1-0-15-14-13-...8-23-22-...16-31...24 Bit 24 is the last bit shifted out/in. There are no alignment assumptions; byte 0 always represents the value specified by the cycle address. The data in this register may be modified by the hardware during any programmed SPI transaction. Direct Memory Reads do not modify the contents of this register. FDATAN--Flash Data [N] Register (SPI Memory Mapped Configuration Registers) Memory Address: SPIBAR + 14h SPIBAR + 18h SPIBAR + 1Ch SPIBAR + 20h SPIBAR + 24h SPIBAR + 28h SPIBAR + 2Ch SPIBAR + 30h SPIBAR + 34h SPIBAR + 38h SPIBAR + 3Ch SPIBAR + 40h SPIBAR + 44h SPIBAR + 48h SPIBAR + 4Ch Default Value: 00000000h Bit 31:0 Datasheet R/W 32 bits Attribute: R/W Size: 32 bits Description Flash Data N (FD[N])--R/W. Similar definition as Flash Data 0. However, this register does not begin shifting until FD[N-1] has completely shifted in/out. 727 Serial Peripheral Interface (SPI) 21.1.7 FRAP--Flash Regions Access Permissions Register (SPI Memory Mapped Configuration Registers) Memory Address: SPIBAR + 50h Default Value: 00000202h Note: 21.1.8 Attribute: Size: This register is only applicable when SPI device is in descriptor mode. Bit Description 31:24 BIOS Master Write Access Grant (BMWAG)--R/W. Each bit [31:24] corresponds to Master[7:0]. BIOS can grant one or more masters write access to the BIOS region 1 overriding the permissions in the Flash Descriptor. Master[1] is Host processor/BIOS, Master[2] is Intel Management Engine, Master[3] is Host processor/GbE. Master[0] and Master[7:4] are reserved. The contents of this register field are locked by the FLOCKDN bit. 23:16 BIOS Master Read Access Grant (BMRAG)--R/W. Each bit [23:16] corresponds to Master[7:0]. BIOS can grant one or more masters read access to the BIOS region 1 overriding the read permissions in the Flash Descriptor. Master[1] is Host processor/BIOS, Master[2] is Intel Management Engine, Master[3] is Host processor/GbE. Master[0] and Master[7:4] are reserved. The contents of this register field are locked by the FLOCKDN bit 15:8 BIOS Region Write Access (BRWA)--RO. Each bit [15:8] corresponds to Regions [7:0]. If the bit is set, this master can erase and write that particular region through register accesses. The contents of this register field are that of the Flash Descriptor. Flash Master 1 Master Region Write Access OR a particular master has granted BIOS write permissions in their Master Write Access Grant register or the Flash Descriptor Security Override strap is set. 7:0 BIOS Region Read Access (BRRA)--RO. Each bit [7:0] corresponds to Regions [7:0]. If the bit is set, this master can read that particular region through register accesses. The contents of this register field are that of the Flash Descriptor.Flash Master 1.Master Region Write Access OR a particular master has granted BIOS read permissions in their Master Read Access Grant register or the Flash Descriptor Security Override strap is set. FREG0--Flash Region 0 (Flash Descriptor) Register (SPI Memory Mapped Configuration Registers) Memory Address: SPIBAR + 54h Default Value: 00000000h Note: Attribute: Size: RO 32 bits This register is only applicable when SPI device is in descriptor mode. Bit Description 31:29 Reserved 28:16 Region Limit (RL)--RO. This specifies address bits 24:12 for the Region 0 Limit. The value in this register is loaded from the contents in the Flash Descriptor.FLREG0.Region Limit. 15:13 Reserved 12:0 728 RO, R/W 32 bits Region Base (RB) / Flash Descriptor Base Address Region (FdBAR)--RO. This specifies address bits 24:12 for the Region 0 Base The value in this register is loaded from the contents in the Flash Descriptor.FLREG0.Region Base. Datasheet Serial Peripheral Interface (SPI) 21.1.9 FREG1--Flash Region 1 (BIOS Descriptor) Register (SPI Memory Mapped Configuration Registers) Memory Address: SPIBAR + 58h Default Value: 00000000h Note: Description 31:29 Reserved 28:16 Region Limit (RL)--RO. This specifies address bits 24:12 for the Region 1 Limit. The value in this register is loaded from the contents in the Flash Descriptor.FLREG1.Region Limit. 15:13 Reserved 12:0 Region Base (RB)--RO. This specifies address bits 24:12 for the Region 1 Base The value in this register is loaded from the contents in the Flash Descriptor.FLREG1.Region Base. FREG2--Flash Region 2 (Intel(R) ME) Register (SPI Memory Mapped Configuration Registers) Memory Address: SPIBAR + 5Ch Default Value: 00000000h Note: Attribute: Size: Description 31:29 Reserved 28:16 Region Limit (RL)--RO. This specifies address bits 24:12 for the Region 2 Limit. The value in this register is loaded from the contents in the Flash Descriptor.FLREG2.Region Limit. 15:13 12:0 Reserved Region Base (RB)--RO. This specifies address bits 24:12 for the Region 2 Base The value in this register is loaded from the contents in the Flash Descriptor.FLREG2.Region Base FREG3--Flash Region 3 (GbE) Register (SPI Memory Mapped Configuration Registers) Memory Address: SPIBAR + 60h Default Value: 00000000h Note: Attribute: Size: RO 32 bits This register is only applicable when SPI device is in descriptor mode. Bit Description 31:29 Reserved 28:16 Region Limit (RL)--RO. This specifies address bits 24:12 for the Region 3 Limit. The value in this register is loaded from the contents in the Flash Descriptor.FLREG3.Region Limit. 15:13 Reserved 12:0 Datasheet RO 32 bits This register is only applicable when SPI device is in descriptor mode. Bit 21.1.11 RO 32 bits This register is only applicable when SPI device is in descriptor mode. Bit 21.1.10 Attribute: Size: Region Base (RB)--RO. This specifies address bits 24:12 for the Region 3 Base The value in this register is loaded from the contents in the Flash Descriptor.FLREG3.Region Base 729 Serial Peripheral Interface (SPI) 21.1.12 FREG4--Flash Region 4 (Platform Data) Register (SPI Memory Mapped Configuration Registers) Memory Address: SPIBAR + 64h Default Value: 00000000h Note: Description 31:29 Reserved 28:16 Region Limit (RL)--RO. This specifies address bits 24:12 for the Region 4 Limit. The value in this register is loaded from the contents in the Flash Descriptor.FLREG4.Region Limit. 15:13 Reserved 12:0 Region Base (RB)--RO. This specifies address bits 24:12 for the Region 4 Base The value in this register is loaded from the contents in the Flash Descriptor.FLREG4.Region Base. PR0--Protected Range 0 Register (SPI Memory Mapped Configuration Registers) Memory Address: SPIBAR + 74h Default Value: 00000000h Note: Attribute: Size: R/W 32 bits This register can not be written when the FLOCKDN bit is set to 1. Bit 31 30:29 28:16 15 14:13 12:0 730 RO 32 bits This register is only applicable when SPI device is in descriptor mode. Bit 21.1.13 Attribute: Size: Description Write Protection Enable--R/W. When set, this bit indicates that the Base and Limit fields in this register are valid and that writes and erases directed to addresses between them (inclusive) must be blocked by hardware. The base and limit fields are ignored when this bit is cleared. Reserved Protected Range Limit--R/W. This field corresponds to FLA address bits 24:12 and specifies the upper limit of the protected range. Address bits 11:0 are assumed to be FFFh for the limit comparison. Any address greater than the value programmed in this field is unaffected by this protected range. Read Protection Enable--R/W. When set, this bit indicates that the Base and Limit fields in this register are valid and that read directed to addresses between them (inclusive) must be blocked by hardware. The base and limit fields are ignored when this bit is cleared. Reserved Protected Range Base--R/W. This field corresponds to FLA address bits 24:12 and specifies the lower base of the protected range. Address bits 11:0 are assumed to be 000h for the base comparison. Any address less than the value programmed in this field is unaffected by this protected range. Datasheet Serial Peripheral Interface (SPI) 21.1.14 PR1--Protected Range 1 Register (SPI Memory Mapped Configuration Registers) Memory Address: SPIBAR + 78h Default Value: 00000000h Note: 31 30:29 28:16 15 14:13 12:0 Description Write Protection Enable--R/W. When set, this bit indicates that the Base and Limit fields in this register are valid and that writes and erases directed to addresses between them (inclusive) must be blocked by hardware. The base and limit fields are ignored when this bit is cleared. Reserved Protected Range Limit--R/W. This field corresponds to FLA address bits 24:12 and specifies the upper limit of the protected range. Address bits 11:0 are assumed to be FFFh for the limit comparison. Any address greater than the value programmed in this field is unaffected by this protected range. Read Protection Enable--R/W. When set, this bit indicates that the Base and Limit fields in this register are valid and that read directed to addresses between them (inclusive) must be blocked by hardware. The base and limit fields are ignored when this bit is cleared. Reserved Protected Range Base--R/W. This field corresponds to FLA address bits 24:12 and specifies the lower base of the protected range. Address bits 11:0 are assumed to be 000h for the base comparison. Any address less than the value programmed in this field is unaffected by this protected range. PR2--Protected Range 2 Register (SPI Memory Mapped Configuration Registers) Memory Address: SPIBAR + 7Ch Default Value: 00000000h Note: Attribute: Size: R/W 32 bits This register can not be written when the FLOCKDN bit is set to 1. Bit 31 30:29 28:16 15 14:13 12:0 Datasheet R/W 32 bits This register can not be written when the FLOCKDN bit is set to 1. Bit 21.1.15 Attribute: Size: Description Write Protection Enable--R/W. When set, this bit indicates that the Base and Limit fields in this register are valid and that writes and erases directed to addresses between them (inclusive) must be blocked by hardware. The base and limit fields are ignored when this bit is cleared. Reserved Protected Range Limit--R/W. This field corresponds to FLA address bits 24:12 and specifies the upper limit of the protected range. Address bits 11:0 are assumed to be FFFh for the limit comparison. Any address greater than the value programmed in this field is unaffected by this protected range. Read Protection Enable--R/W. When set, this bit indicates that the Base and Limit fields in this register are valid and that read directed to addresses between them (inclusive) must be blocked by hardware. The base and limit fields are ignored when this bit is cleared. Reserved Protected Range Base--R/W. This field corresponds to FLA address bits 24:12 and specifies the lower base of the protected range. Address bits 11:0 are assumed to be 000h for the base comparison. Any address less than the value programmed in this field is unaffected by this protected range. 731 Serial Peripheral Interface (SPI) 21.1.16 PR3--Protected Range 3 Register (SPI Memory Mapped Configuration Registers) Memory Address: SPIBAR + 80h Default Value: 00000000h Note: 31 30:29 28:16 15 14:13 12:0 Description Write Protection Enable--R/W. When set, this bit indicates that the Base and Limit fields in this register are valid and that writes and erases directed to addresses between them (inclusive) must be blocked by hardware. The base and limit fields are ignored when this bit is cleared. Reserved Protected Range Limit--R/W. This field corresponds to FLA address bits 24:12 and specifies the upper limit of the protected range. Address bits 11:0 are assumed to be FFFh for the limit comparison. Any address greater than the value programmed in this field is unaffected by this protected range. Read Protection Enable--R/W. When set, this bit indicates that the Base and Limit fields in this register are valid and that read directed to addresses between them (inclusive) must be blocked by hardware. The base and limit fields are ignored when this bit is cleared. Reserved Protected Range Base--R/W. This field corresponds to FLA address bits 24:12 and specifies the lower base of the protected range. Address bits 11:0 are assumed to be 000h for the base comparison. Any address less than the value programmed in this field is unaffected by this protected range. PR4--Protected Range 4 Register (SPI Memory Mapped Configuration Registers) Memory Address: SPIBAR + 84h Default Value: 00000000h Note: Attribute: Size: R/W 32 bits This register can not be written when the FLOCKDN bit is set to 1. Bit Description 31 Write Protection Enable--R/W. When set, this bit indicates that the Base and Limit fields in this register are valid and that writes and erases directed to addresses between them (inclusive) must be blocked by hardware. The base and limit fields are ignored when this bit is cleared. 30:29 28:16 15 14:13 12:0 732 R/W 32 bits This register can not be written when the FLOCKDN bit is set to 1. Bit 21.1.17 Attribute: Size: Reserved Protected Range Limit--R/W. This field corresponds to FLA address bits 24:12 and specifies the upper limit of the protected range. Address bits 11:0 are assumed to be FFFh for the limit comparison. Any address greater than the value programmed in this field is unaffected by this protected range. Read Protection Enable--R/W. When set, this bit indicates that the Base and Limit fields in this register are valid and that read directed to addresses between them (inclusive) must be blocked by hardware. The base and limit fields are ignored when this bit is cleared. Reserved Protected Range Base--R/W. This field corresponds to FLA address bits 24:12 and specifies the lower base of the protected range. Address bits 11:0 are assumed to be 000h for the base comparison. Any address less than the value programmed in this field is unaffected by this protected range. Datasheet Serial Peripheral Interface (SPI) 21.1.18 SSFS--Software Sequencing Flash Status Register (SPI Memory Mapped Configuration Registers) Memory Address: SPIBAR + 90h Default Value: 00h Note: RO, R/WC 8 bits The Software Sequencing control and status registers are reserved if the hardware sequencing control and status registers are used. Bit 7:5 Datasheet Attribute: Size: Description Reserved 4 Access Error Log (AEL)--RO. This bit reflects the value of the Hardware Sequencing Status AEL register. 3 Flash Cycle Error (FCERR)--R/WC. Hardware sets this bit to 1 when a programmed access is blocked from running on the SPI interface due to one of the protection policies or when any of the programmed cycle registers is written while a programmed access is already in progress. This bit remains asserted until cleared by software writing a 1 or hardware reset due to a global reset or host partition reset in an Intel ME enabled system. 2 Cycle Done Status--R/WC. The PCH sets this bit to 1 when the SPI Cycle completes (that is, SCIP bit is 0) after software sets the GO bit. This bit remains asserted until cleared by software writing a 1 or hardware reset due to a global reset or host partition reset in an Intel ME enabled system. When this bit is set and the SPI SMI# Enable bit is set, an internal signal is asserted to the SMI# generation block. Software must make sure this bit is cleared prior to enabling the SPI SMI# assertion for a new programmed access. 1 Reserved 0 SPI Cycle In Progress (SCIP)--RO. Hardware sets this bit when software sets the SPI Cycle Go bit in the Command register. This bit remains set until the cycle completes on the SPI interface. Hardware automatically sets and clears this bit so that software can determine when read data is valid and/or when it is safe to begin programming the next command. Software must only program the next command when this bit is 0. 733 Serial Peripheral Interface (SPI) 21.1.19 SSFC--Software Sequencing Flash Control Register (SPI Memory Mapped Configuration Registers) Memory Address: SPIBAR + 91h Default Value: F80000h Bit R/W 24 bits Description 23:19 Reserved - BIOS must set this field to `11111'b 18:16 SPI Cycle Frequency (SCF)--R/W. This register sets frequency to use for all SPI software sequencing cycles (write, erase, fast read, read status, and so on) except for the read cycle which always run at 20 MHz. 000 = 20 MHz 001 = 33 MHz 100 = 50 MHz All other values reserved. This register is locked when the SPI Configuration Lock-Down bit is set. 15 SPI SMI# Enable (SME)--R/W. When set to 1, the SPI asserts an SMI# request whenever the Cycle Done Status bit is 1. 14 Data Cycle (DS)--R/W. When set to 1, there is data that corresponds to this transaction. When 0, no data is delivered for this cycle, and the dBC and data fields themselves are don't cares. 13:8 Data Byte Count (dBC)--R/W. This field specifies the number of bytes to shift in or out during the data portion of the SPI cycle. The valid settings (in decimal) are any value from 0 to 63. The number of bytes transferred is the value of this field plus 1. When this field is 00_0000b, there is 1 byte to transfer and that 11_1111b means there are 64 bytes to transfer. 7 734 Attribute: Size: Reserved 6:4 Cycle Opcode Pointer (COP)--R/W. This field selects one of the programmed opcodes in the Opcode Menu to be used as the SPI Command/Opcode. In the case of an Atomic Cycle Sequence, this determines the second command. 3 Sequence Prefix Opcode Pointer (SPOP)--R/W. This field selects one of the two programmed prefix opcodes for use when performing an Atomic Cycle Sequence. A value of 0 points to the opcode in the least significant byte of the Prefix Opcodes register. By making this programmable, the PCH supports flash devices that have different opcodes for enabling writes to the data space versus status register. 2 Atomic Cycle Sequence (ACS)--R/W. When set to 1 along with the SCGO assertion, the PCH will execute a sequence of commands on the SPI interface without allowing the LAN component to arbitrate and interleave cycles. The sequence is composed of: * Atomic Sequence Prefix Command (8-bit opcode only) * Primary Command specified below by software (can include address and data) * Polling the Flash Status Register (opcode 05h) until bit 0 becomes 0b. The SPI Cycle in Progress bit remains set and the Cycle Done Status bit remains unset until the Busy bit in the Flash Status Register returns 0. 1 SPI Cycle Go (SCGO)--R/WS. This bit always returns 0 on reads. However, a write to this register with a 1 in this bit starts the SPI cycle defined by the other bits of this register. The "SPI Cycle in Progress" (SCIP) bit gets set by this action. Hardware must ignore writes to this bit while the Cycle In Progress bit is set. Hardware allows other bits in this register to be programmed for the same transaction when writing this bit to 1. This saves an additional memory write. 0 Reserved Datasheet Serial Peripheral Interface (SPI) 21.1.20 PREOP--Prefix Opcode Configuration Register (SPI Memory Mapped Configuration Registers) Memory Address: SPIBAR + 94h Default Value: 0000h R/W 16 bits Bit Description 15:8 Prefix Opcode 1--R/W. Software programs an SPI opcode into this field that is permitted to run as the first command in an atomic cycle sequence. 7:0 Prefix Opcode 0--R/W. Software programs an SPI opcode into this field that is permitted to run as the first command in an atomic cycle sequence. Note: 21.1.21 Attribute: Size: This register is not writable when the Flash Configuration Lock-Down bit (SPIBAR + 04h:15) is set. OPTYPE--Opcode Type Configuration Register (SPI Memory Mapped Configuration Registers) Memory Address: SPIBAR + 96h Default Value: 0000h Attribute: Size: R/W 16 bits Entries in this register correspond to the entries in the Opcode Menu Configuration register. Note: The definition below only provides write protection for opcodes that have addresses associated with them. Therefore, any erase or write opcodes that do not use an address should be avoided (for example, "Chip Erase" and "Auto-Address Increment Byte Program") Bit 15:14 Opcode Type 7--R/W. See the description for bits 1:0 13:12 Opcode Type 6--R/W. See the description for bits 1:0 11:10 Opcode Type 5--R/W. See the description for bits 1:0 9:8 Opcode Type 4--R/W. See the description for bits 1:0 7:6 Opcode Type 3--R/W. See the description for bits 1:0 5:4 Opcode Type 2--R/W. See the description for bits 1:0 3:2 Opcode Type 1--R/W. See the description for bits 1:0 1:0 Opcode Type 0--R/W. This field specifies information about the corresponding Opcode 0. This information allows the hardware to 1) know whether to use the address field and 2) provide BIOS and Shared Flash protection capabilities. The encoding of the two bits is: 00 = No address associated with this Opcode; Read cycle type 01 = No address associated with this Opcode; Write cycle type 10 = Address required; Read cycle type 11 = Address required; Write cycle type Note: Datasheet Description This register is not writable when the SPI Configuration Lock-Down bit (SPIBAR + 00h:15) is set. 735 Serial Peripheral Interface (SPI) 21.1.22 OPMENU--Opcode Menu Configuration Register (SPI Memory Mapped Configuration Registers) Memory Address: SPIBAR + 98h Default Value: 0000000000000000h Attribute: Size: R/W 64 bits Eight entries are available in this register to give BIOS a sufficient set of commands for communicating with the flash device, while also restricting what malicious software can do. This keeps the hardware flexible enough to operate with a wide variety of SPI devices. Note: It is recommended that BIOS avoid programming Write Enable opcodes in this menu. Malicious software could then perform writes and erases to the SPI flash without using the atomic cycle mechanism. This could cause functional failures in a shared flash environment. Write Enable opcodes should only be programmed in the Prefix Opcodes. Bit Description 63:56 Allowable Opcode 7--R/W. See the description for bits 7:0 55:48 Allowable Opcode 6--R/W. See the description for bits 7:0 47:40 Allowable Opcode 5--R/W. See the description for bits 7:0 39:32 Allowable Opcode 4--R/W. See the description for bits 7:0 31:24 Allowable Opcode 3--R/W. See the description for bits 7:0 23:16 Allowable Opcode 2--R/W. See the description for bits 7:0 15:8 Allowable Opcode 1--R/W. See the description for bits 7:0 7:0 Allowable Opcode 0--R/W. Software programs an SPI opcode into this field for use when initiating SPI commands through the Control Register. This register is not writable when the SPI Configuration Lock-Down bit (SPIBAR + 00h:15) is set. 21.1.23 BBAR--BIOS Base Address Configuration Register (SPI Memory Mapped Configuration Registers) Memory Address: SPIBAR + A0h Default Value: 00000000h Attribute: Size: R/W, RO 32 bits Eight entries are available in this register to give BIOS a sufficient set of commands for communicating with the flash device, while also restricting what malicious software can do. This keeps the hardware flexible enough to operate with a wide variety of SPI devices. Bit 31:24 23:8 7:0 736 Description Reserved Bottom of System Flash--R/W. This field determines the bottom of the System BIOS. The PCH will not run programmed commands nor memory reads whose address field is less than this value. this field corresponds to bits 23:8 of the 3-byte address; bits 7:0 are assumed to be 00h for this vector when comparing to a potential SPI address. Note: The SPI host controller prevents any programmed cycle using the address register with an address less than the value in this register. Some flash devices specify that the Read ID command must have an address of 0000h or 0001h. If this command must be supported with these devices, it must be performed with the BIOS BAR. Reserved Datasheet Serial Peripheral Interface (SPI) 21.1.24 FDOC--Flash Descriptor Observability Control Register (SPI Memory Mapped Configuration Registers) Memory Address: SPIBAR + B0h Default Value: 00000000h Note: Description 31:15 Reserved 14:12 Flash Descriptor Section Select (FDSS)--R/W. Selects which section within the loaded Flash Descriptor to observe. 000 = Flash Signature and Descriptor Map 001 = Component 010 = Region 011 = Master 111 = Reserved 11:2 1:0 Flash Descriptor Section Index (FDSI)--R/W. Selects the DW offset within the Flash Descriptor Section to observe. Reserved FDOD--Flash Descriptor Observability Data Register (SPI Memory Mapped Configuration Registers) Memory Address: SPIBAR + B4h Default Value: 00000000h Note: Attribute: Size: 31:0 Description Flash Descriptor Section Data (FDSD)--RO. Returns the DW of data to observe as selected in the Flash Descriptor Observability Control. AFC--Additional Flash Control Register (SPI Memory Mapped Configuration Registers) Memory Address: SPIBAR + C0h Default Value: 00000000h Bit 31:3 2:1 0 Datasheet RO 32 bits This register that can be used to observe the contents of the Flash Descriptor that is stored in the PCH Flash Controller. Bit 21.1.26 R/W 32 bits This register that can be used to observe the contents of the Flash Descriptor that is stored in the PCH Flash Controller. This register is only applicable when SPI device is in descriptor mode. Bit 21.1.25 Attribute: Size: Attribute: Size: RO, R/W 32 bits. Description Reserved Flash Controller Interface Dynamic Clock Gating Enable--R/W. 00 = Flash Controller Interface Dynamic Clock Gating is Disabled 11 = Flash Controller Interface Dynamic Clock Gating is Enabled Other encodings are Reserved. Flash Controller Core Dynamic Clock Gating Enable--R/W. 0 = Flash Controller Core Dynamic Clock Gating is Disabled 1 = Flash Controller Core Dynamic Clock Gating is Enabled 737 Serial Peripheral Interface (SPI) 21.1.27 LVSCC--Host Lower Vendor Specific Component Capabilities Register (SPI Memory Mapped Configuration Registers) Memory Address: SPIBAR + C4h Default Value: 00000000h Note: RO, R/WL 32 bits All attributes described in LVSCC must apply to all flash space below the FPBA, even if it spans between two separate flash parts. This register is only applicable when SPI device is in descriptor mode. Bit 31:24 23 22:16 15:8 7:5 738 Attribute: Size: Description Reserved Vendor Component Lock (LVCL)--R/W. This register locks itself when set. 0 = The lock bit is not set 1 = The Vendor Component Lock bit is set. Note: This bit applies to both UVSCC and LVSCC registers. Reserved Lower Erase Opcode (LEO)--R/W. This register is programmed with the Flash erase instruction opcode required by the vendor's Flash component. This register is locked by the Vendor Component Lock (LVCL) bit. Reserved 4 Write Enable on Write Status (LWEWS)--R/W. This register is locked by the Vendor Component Lock (LVCL) bit. 0 = No automatic write of 00h will be made to the SPI flash's status register) 1 = A write of 00h to the SPI flash's status register will be sent on EVERY write and erase to the SPI flash. 06h 01h 00h is the opcode sequence used to unlock the Status register. Notes: 1. This bit should not be set to 1 if there are non-volatile bits in the SPI flash's status register. This may lead to premature flash wear out. 2. This is not an atomic sequence. If the SPI component's status register is non-volatile, then BIOS should issue an atomic software sequence cycle to unlock the flash part. 3. Bit 3 and bit 4 should NOT be both set to 1. 3 Lower Write Status Required (LWSR)--R/W. This register is locked by the Vendor Component Lock (LVCL) bit. 0 = No automatic write of 00h will be made to the SPI flash's status register) 1 = A write of 00h to the SPI flash's status register will be sent on EVERY write and erase to the SPI flash. 50h 01h 00h is the opcode sequence used to unlock the Status register. Notes: 1. This bit should not be set to 1 if there are non volatile bits in the SPI flash's status register. This may lead to premature flash wear out. 2. This is not an atomic sequence. If the SPI component's status register is non-volatile, then BIOS should issue an atomic software sequence cycle to unlock the flash part. 3. Bit 3 and bit 4 should NOT be both set to 1. 2 Lower Write Granularity (LWG)--R/W. This register is locked by the Vendor Component Lock (LVCL) bit. 0 = 1 Byte 1 = 64 Byte Notes: 1. If more than one Flash component exists, this field must be set to the lowest common write granularity of the different Flash components. 2. If using 64 B write, BIOS must ensure that multiple byte writes do not occur over 256 B boundaries. This will lead to corruption as the write will wrap around the page boundary on the SPI flash part. This is a a feature page writable SPI flash. 1:0 Lower Block/Sector Erase Size (LBES)--R/W. This field identifies the erasable sector size for all Flash components. 00 = 256 Byte 01 = 4 KB 10 = 8 KB 11 = 64 KB This register is locked by the Vendor Component Lock (LVCL) bit. Hardware takes no action based on the value of this register. The contents of this register are to be used only by software and can be read in the HSFSTS.BERASE register in both the BIOS and the GbE program registers if FLA is less than FPBA. Datasheet Serial Peripheral Interface (SPI) 21.1.28 UVSCC--Host Upper Vendor Specific Component Capabilities Register (SPI Memory Mapped Configuration Registers) Memory Address: SPIBAR + C8h Default Value: 00000000h Attribute: Size: RO, R/WL 32 bits Note: All attributes described in UVSCC must apply to all flash space equal to or above the FPBA, even if it spans between two separate flash parts. This register is only applicable when SPI device is in descriptor mode. Note: To prevent this register from being modified you must use LVSCC.VCL bit. Bit 31:16 15:8 7:5 4 Description Reserved Upper Erase Opcode (UEO)--R/W. This register is programmed with the Flash erase instruction opcode required by the vendor's Flash component. This register is locked by the Vendor Component Lock (UVCL) bit. Reserved Write Enable on Write Status (UWEWS)--R/W. This register is locked by the Vendor Component Lock (UVCL) bit. 0 = No automatic write of 00h will be made to the SPI flash's status register) 1 = A write of 00h to the SPI flash's status register will be sent on EVERY write and erase to the SPI flash. 06h 01h 00h is the opcode sequence used to unlock the Status register. Notes: 1. This bit should not be set to 1 if there are non volatile bits in the SPI flash's status register. This may lead to premature flash wear out. 2. This is not an atomic sequence. If the SPI component's status register is non-volatile, then BIOS should issue an atomic software sequence cycle to unlock the flash part. 3. Bit 3 and bit 4 should NOT be both set to 1. 3 Upper Write Status Required (UWSR)--R/W. This register is locked by the Vendor Component Lock (UVCL) bit. 0 = No automatic write of 00h will be made to the SPI flash's status register) 1 = A write of 00h to the SPI flash's status register will be sent on EVERY write and erase to the SPI flash. 50h 01h 00h is the opcode sequence used to unlock the Status register. Notes: 1. This bit should not be set to `1' if there are non volatile bits in the SPI flash's status register. This may lead to premature flash wear out. 2. This is not an atomic sequence. If the SPI component's status register is non-volatile, then BIOS should issue an atomic software sequence cycle to unlock the flash part. 3. Bit 3 and bit 4 should NOT be both set to 1. 2 Upper Write Granularity (UWG)--R/W. This register is locked by the Vendor Component Lock (UVCL) bit. 0 = 1 Byte 1 = 64 Byte Notes: 1. If more than one Flash component exists, this field must be set to the lowest common write granularity of the different Flash components. 2. If using 64 B write, BIOS must ensure that multiple byte writes do not occur over 256 B boundaries. This will lead to corruption as the write will wrap around the page boundary on the SPI flash part. This is a a feature page writable SPI flash. 1:0 Datasheet Upper Block/Sector Erase Size (UBES)--R/W. This field identifies the erasable sector size for all Flash components. Valid Bit Settings: 00 = 256 Byte 01 = 4 KB 10 = 8 KB 11 = 64 KB This register is locked by the Vendor Component Lock (UVCL) bit. Hardware takes no action based on the value of this register. The contents of this register are to be used only by software and can be read in the HSFSTS.BERASE register in both the BIOS and the GbE program registers if FLA is greater or equal to FPBA. 739 Serial Peripheral Interface (SPI) 21.1.29 PTINX--Flash Parameter Table Index Register Memory Address: SPIBAR + CCh Default Value: 00000000h Note: Description 31:16 Reserved. 15:14 Supported Parameter Table (PTINXSPT) - RO/V. Selects which supported parameter table to observe. 00 =Component 0 Property Parameter Table 01 =Component 1 Property Parameter Table 10 - 11 = Reserved 13:12 Header or Data (PTINXHORD) - RO/V. Select parameter table header DWord versus Data DWord. 00 = SFDP Header 01 = Parameter Table Header 10 = Data 11 = Reserved 11:2 1:0 Parameter Table DW Index (PTINXPTDWI) - RO/V. Selects the DWord offset within the parameter table to observe. Reserved. PTDATA--Flash Parameter Table Data Register Memory Address: SPIBAR + D0h Default Value: 00000000h Note: 21.1.31 Attribute: Size: RO/V 32 bits This register is only applicable when SPI device is in descriptor mode. Bit Description 31:0 Parameter Table DW Data (PTDWD) - RO/V. Returns the DWord of data to observe as selected in the Parameter Table Index register. Note: The returned value of reserved fields in the SFDP header or table must be ignored by software. The flash controller may return either 0 or 1 for these fields. SRDL--Soft Reset Data Lock Register (SPI Memory Mapped Configuration Registers) Memory Address: SPIBAR + F0h Default Value: 00000000h Bit 31:1 0 740 RO, RW 32 bits This register is only applicable when SPI device is in descriptor mode. Bit 21.1.30 Attribute: Size: Attribute: Size: R/WL 32 bits Description Reserved Set_Stap Lock (SSL)--R/WL. 0 = The SRDL (this register), SRDC (SPIBAR+F4h), and SRD (SPIBAR+F4h) registers are writeable. 1 = The SRDL (this register), SRDC (SPIBAR+F4h), and SRD (SPIBAR+F4h) registers are locked. Note: That this bit is reset to `0' on CF9h resets. Datasheet Serial Peripheral Interface (SPI) 21.1.32 SRDC--Soft Reset Data Control Register (SPI Memory Mapped Configuration Registers) Memory Address: SPIBAR + F4h Default Value: 00000000h Bit 31:1 0 21.1.33 Attribute: Size: Description Reserved Soft Reset Data Select (SRDS)--R/WL. 0 = The Set_Strap data sends the default processor configuration data. 1 = The Set_Strap message bits come from the Set_Strap Msg Data register. Notes: 1. This bit is reset by the RSMRST# or when the Resume well loses power. 2. This bit is locked by the SSL bit (SPIBAR+F0h:bit 0). SRD--Soft Reset Data Register (SPI Memory Mapped Configuration Registers) Memory Address: SPIBAR + F8h Default Value: 00000000h Bit 31:14 13:0 21.2 R/WL 32 bits Attribute: Size: R/WL 32 bits Description Reserved Set_Stap Data (SSD)--R/WL. Notes: 1. These bits are reset by the RSMRST#, or when the Resume well loses power. 2. These bits are locked by the SSL bit (SPIBAR+F0h:bit 0). Flash Descriptor Records The following sections describe the data structure of the Flash Descriptor on the SPI device. These are not registers within the PCH. 21.3 OEM Section Memory Address: F00h Default Value: Size: 256 Bytes 256 Bytes are reserved at the top of the Flash Descriptor for use by the OEM. The information stored by the OEM can only be written during the manufacturing process as the Flash Descriptor read/write permissions must be set to Read Only when the computer leaves the manufacturing floor. The PCH Flash controller does not read this information. FFh is suggested to reduce programming time. Datasheet 741 Serial Peripheral Interface (SPI) 21.4 GbE SPI Flash Program Registers The GbE Flash registers are memory-mapped with a base address MBARB found in the GbE LAN register chapter Device 25: Function 0: Offset 14h. The individual registers are then accessible at MBARB + Offset as indicated in the following table. These memory mapped registers must be accessed in byte, word, or DWord quantities. Note: These register are only applicable when SPI flash is used in descriptor mode. Table 21-1. Gigabit LAN SPI Flash Program Register Address Map (GbE LAN Memory Mapped Configuration Registers) 742 MBARB + Offset Mnemonic 00h-03h GLFPR Gigabit LAN Flash Primary Region 04h-05h HSFS Hardware Sequencing Flash Status 06h-07h HSFC 08h-0Bh FADDR 0Ch-0Fh -- 10h-13h FDATA0 14h-4Fh -- 50h-53h FRAP Register Name Hardware Sequencing Flash Control Flash Address Default Attribute 00000000h RO 0000h RO, R/WC, R/ W 0000h R/W, R/WS 00000000h R/W Reserved 00000000h Flash Data 0 00000000h R/W Reserved 00000000h Flash Region Access Permissions 00000000h RO, R/W 54h-57h FREG0 Flash Region 0 00000000h RO 58h-5Bh FREG1 Flash Region 1 00000000h RO 5Ch-5F FREG2 Flash Region 2 00000000h RO 60h-63h FREG3 Flash Region 3 00000000h RO Flash Protected Range 0 00000000h R/W Flash Protected Range 1 00000000h R/W 64h-73h -- 74h-77h PR0 78h-7Bh PR1 7Ch-8Fh -- Reserved for Future Flash Regions Reserved 90h SSFS Software Sequencing Flash Status 00h RO, R/WC 91h-93h SSFC Software Sequencing Flash Control 000000h R/W 94h-95h PREOP Prefix Opcode Configuration 0000h R/W 96h-97h OPTYPE Opcode Type Configuration 0000h R/W 98h-9Fh OPMENU Opcode Menu Configuration 000000000000 0000h R/W A0h-DFh -- Reserved Datasheet Serial Peripheral Interface (SPI) 21.4.1 GLFPR -Gigabit LAN Flash Primary Region Register (GbE LAN Memory Mapped Configuration Registers) Memory Address: MBARB + 00h Default Value: 00000000h Bit 31:29 28:16 15:13 12:0 21.4.2 Attribute: Size: Description Reserved GbE Flash Primary Region Limit (PRL)--RO. This specifies address bits 24:12 for the Primary Region Limit. The value in this register loaded from the contents in the Flash Descriptor.FLREG3.Region Limit Reserved GbE Flash Primary Region Base (PRB)--RO. This specifies address bits 24:12 for the Primary Region Base The value in this register is loaded from the contents in the Flash Descriptor.FLREG3.Region Base HSFS--Hardware Sequencing Flash Status Register (GbE LAN Memory Mapped Configuration Registers) Memory Address: MBARB + 04h Default Value: 0000h Bit Attribute: Size: RO, R/WC, R/W 16 bits Description 15 Flash Configuration Lock-Down (FLOCKDN)--R/W. When set to 1, those Flash Program Registers that are locked down by this FLOCKDN bit cannot be written. Once set to 1, this bit can only be cleared by a hardware reset due to a global reset or host partition reset in an Intel ME enabled system. 14 Flash Descriptor Valid (FDV)--RO. This bit is set to a 1 if the Flash Controller read the correct Flash Descriptor Signature. If the Flash Descriptor Valid bit is not 1, software cannot use the Hardware Sequencing registers, but must use the software sequencing registers. Any attempt to use the Hardware Sequencing registers will result in the FCERR bit being set. 13 Flash Descriptor Override Pin Strap Status (FDOPSS)--RO. This bit indicates the condition of the Flash Descriptor Security Override / Intel ME Debug Mode pin strap. 0 = The Flash Descriptor Security Override / Intel ME Debug Mode strap is set using external pullup on HDA_SDO 1 = No override 12:6 Datasheet RO 32 bits Reserved 5 SPI Cycle In Progress (SCIP)--RO. Hardware sets this bit when software sets the Flash Cycle Go (FGO) bit in the Hardware Sequencing Flash Control register. This bit remains set until the cycle completes on the SPI interface. Hardware automatically sets and clears this bit so that software can determine when read data is valid and/or when it is safe to begin programming the next command. Software must only program the next command when this bit is 0. 4:3 Block/Sector Erase Size (BERASE)--RO. This field identifies the erasable sector size for all Flash components. 00 = 256 Byte 01 = 4 K Byte 10 = 8 K Byte 11 = 64 K Byte If the Flash Linear Address is less than FPBA then this field reflects the value in the LVSCC.LBES register. If the Flash Linear Address is greater or equal to FPBA then this field reflects the value in the UVSCC.UBES register. 743 Serial Peripheral Interface (SPI) 21.4.3 Bit Description 2 Access Error Log (AEL)--R/W/C. Hardware sets this bit to a 1 when an attempt was made to access the BIOS region using the direct access method or an access to the BIOS Program Registers that violated the security restrictions. This bit is simply a log of an access security violation. This bit is cleared by software writing a 1. 1 Flash Cycle Error (FCERR)--R/W/C. Hardware sets this bit to 1 when an program register access is blocked to the FLASH due to one of the protection policies or when any of the programmed cycle registers is written while a programmed access is already in progress. This bit remains asserted until cleared by software writing a 1 or until hardware reset occurs due to a global reset or host partition reset in an Intel ME enabled system. Software must clear this bit before setting the FLASH Cycle GO bit in this register. 0 Flash Cycle Done (FDONE)--R/W/C. The PCH sets this bit to 1 when the SPI Cycle completes after software previously set the FGO bit. This bit remains asserted until cleared by software writing a 1 or hardware reset due to a global reset or host partition reset in an Intel ME enabled system. When this bit is set and the SPI SMI# Enable bit is set, an internal signal is asserted to the SMI# generation block. Software must make sure this bit is cleared prior to enabling the SPI SMI# assertion for a new programmed access. HSFC--Hardware Sequencing Flash Control Register (GbE LAN Memory Mapped Configuration Registers) Memory Address: MBARB + 06h Default Value: 0000h Bit 15:10 744 Attribute: Size: R/W, R/WS 16 bits Description Reserved 9:8 Flash Data Byte Count (FdBC)--R/W. This field specifies the number of bytes to shift in or out during the data portion of the SPI cycle. The contents of this register are 0s based with 0b representing 1 byte and 11b representing 4 bytes. The number of bytes transferred is the value of this field plus 1. This field is ignored for the Block Erase command. 7:3 Reserved 2:1 FLASH Cycle (FCYCLE)--R/W. This field defines the Flash SPI cycle type generated to the FLASH when the FGO bit is set as defined below: 00 = Read (1 up to 4 bytes by setting FdBC) 01 = Reserved 10 = Write (1 up to 4 bytes by setting FdBC) 11 = Block Erase 0 Flash Cycle Go (FGO)--R/W/S. A write to this register with a 1 in this bit initiates a request to the Flash SPI Arbiter to start a cycle. This register is cleared by hardware when the cycle is granted by the SPI arbiter to run the cycle on the SPI bus. When the cycle is complete, the FDONE bit is set. Software is forbidden to write to any register in the HSFLCTL register between the FGO bit getting set and the FDONE bit being cleared. Any attempt to violate this rule will be ignored by hardware. Hardware allows other bits in this register to be programmed for the same transaction when writing this bit to 1. This saves an additional memory write. This bit always returns 0 on reads. Datasheet Serial Peripheral Interface (SPI) 21.4.4 FADDR--Flash Address Register (GbE LAN Memory Mapped Configuration Registers) Memory Address: MBARB + 08h Default Value: 00000000h Bit 31:25 24:0 21.4.5 Attribute: Size: Description Reserved Flash Linear Address (FLA)--R/W. The FLA is the starting byte linear address of a SPI Read or Write cycle or an address within a Block for the Block Erase command. The Flash Linear Address must fall within a region for which BIOS has access permissions. FDATA0--Flash Data 0 Register (GbE LAN Memory Mapped Configuration Registers) Memory Address: MBARB + 10h Default Value: 00000000h 21.4.6 Attribute: Size: R/W 32 bits Bit Description 31:0 Flash Data 0 (FD0)--R/W. This field is shifted out as the SPI Data on the Master-Out Slave-In Data pin during the data portion of the SPI cycle. This register also shifts in the data from the Master-In Slave-Out pin into this register during the data portion of the SPI cycle. The data is always shifted starting with the least significant byte, msb to lsb, followed by the next least significant byte, msb to lsb, and so on. Specifically, the shift order on SPI in terms of bits within this register is: 7-6-5-4-3-2-1-0-15-14-13-...8-23-22-...16-31...24 Bit 24 is the last bit shifted out/in. There are no alignment assumptions; byte 0 always represents the value specified by the cycle address. The data in this register may be modified by the hardware during any programmed SPI transaction. Direct Memory Reads do not modify the contents of this register. FRAP--Flash Regions Access Permissions Register (GbE LAN Memory Mapped Configuration Registers) Memory Address: MBARB + 50h Default Value: 00000808h Bit Attribute: Size: RO, R/W 32 bits Description 31:28 Reserved 27:25 GbE Master Write Access Grant (GMWAG)--R/W. Each bit 27:25 corresponds to Master[3:1]. GbE can grant one or more masters write access to the GbE region 3 overriding the permissions in the Flash Descriptor. Master[1] is Host Processor/BIOS, Master[2] is Intel Management Engine, Master[3] is Host processor/GbE. The contents of this register are locked by the FLOCKDN bit. 24:20 Reserved 19:17 GbE Master Read Access Grant (GMRAG)--R/W. Each bit 19:17 corresponds to Master[3:1]. GbE can grant one or more masters read access to the GbE region 3 overriding the read permissions in the Flash Descriptor. Master[1] is Host processor/BIOS, Master[2] is Intel Management Engine, Master[3] is GbE. The contents of this register are locked by the FLOCKDN bit 16:12 11:8 Datasheet R/W 32 bits Reserved GbE Region Write Access (GRWA)--RO. Each bit 11:8 corresponds to Regions 3:0. If the bit is set, this master can erase and write that particular region through register accesses. 7:4 Reserved 3:0 GbE Region Read Access (GRRA)--RO. Each bit 3:0 corresponds to Regions 3:0. If the bit is set, this master can read that particular region through register accesses. 745 Serial Peripheral Interface (SPI) 21.4.7 FREG0--Flash Region 0 (Flash Descriptor) Register (GbE LAN Memory Mapped Configuration Registers) Memory Address: MBARB + 54h Default Value: 00000000h Bit Description Reserved 28:16 Region Limit (RL)--RO. This specifies address bits 24:12 for the Region 0 Limit. The value in this register is loaded from the contents in the Flash Descriptor.FLREG0.Region Limit. 15:13 Reserved Region Base (RB)--RO. This specifies address bits 24:12 for the Region 0 Base The value in this register is loaded from the contents in the Flash Descriptor.FLREG0.Region Base. FREG1--Flash Region 1 (BIOS Descriptor) Register (GbE LAN Memory Mapped Configuration Registers) Memory Address: MBARB + 58h Default Value: 00000000h Bit Attribute: Size: Description Reserved 28:16 Region Limit (RL)--RO. This specifies address bits 24:12 for the Region 1 Limit. The value in this register is loaded from the contents in the Flash Descriptor.FLREG1.Region Limit. 15:13 Reserved Region Base (RB)--RO. This specifies address bits 24:12 for the Region 1 Base The value in this register is loaded from the contents in the Flash Descriptor.FLREG1.Region Base. FREG2--Flash Region 2 (Intel(R) ME) Register (GbE LAN Memory Mapped Configuration Registers) Memory Address: MBARB + 5Ch Default Value: 00000000h Bit 746 RO 32 bits 31:29 12:0 21.4.9 RO 32 bits 31:29 12:0 21.4.8 Attribute: Size: Attribute: Size: RO 32 bits Description 31:29 Reserved 28:16 Region Limit (RL)--RO. This specifies address bits 24:12 for the Region 2 Limit. The value in this register is loaded from the contents in the Flash Descriptor.FLREG2.Region Limit. 15:13 Reserved 12:0 Region Base (RB)--RO. This specifies address bits 24:12 for the Region 2 Base The value in this register is loaded from the contents in the Flash Descriptor.FLREG2.Region Base. Datasheet Serial Peripheral Interface (SPI) 21.4.10 FREG3--Flash Region 3 (GbE) Register (GbE LAN Memory Mapped Configuration Registers) Memory Address: MBARB + 60h Default Value: 00000000h Bit Description Reserved 28:16 Region Limit (RL)--RO. This specifies address bits 24:12 for the Region 3 Limit. The value in this register is loaded from the contents in the Flash Descriptor.FLREG3.Region Limit. 12:0 Reserved Region Base (RB)--RO. This specifies address bits 24:12 for the Region 3 Base The value in this register is loaded from the contents in the Flash Descriptor.FLREG3.Region Base. PR0--Protected Range 0 Register (GbE LAN Memory Mapped Configuration Registers) Memory Address: MBARB + 74h Default Value: 00000000h Note: Attribute: Size: R/W 32 bits This register can not be written when the FLOCKDN bit is set to 1. Bit 31 30:29 28:16 15 14:13 12:0 Datasheet RO 32 bits 31:29 15:13 21.4.11 Attribute: Size: Description Write Protection Enable--R/W. When set, this bit indicates that the Base and Limit fields in this register are valid and that writes and erases directed to addresses between them (inclusive) must be blocked by hardware. The base and limit fields are ignored when this bit is cleared. Reserved Protected Range Limit--R/W. This field corresponds to FLA address bits 24:12 and specifies the upper limit of the protected range. Address bits 11:0 are assumed to be FFFh for the limit comparison. Any address greater than the value programmed in this field is unaffected by this protected range. Read Protection Enable--R/W. When set, this bit indicates that the Base and Limit fields in this register are valid and that read directed to addresses between them (inclusive) must be blocked by hardware. The base and limit fields are ignored when this bit is cleared. Reserved Protected Range Base--R/W. This field corresponds to FLA address bits 24:12 and specifies the lower base of the protected range. Address bits 11:0 are assumed to be 000h for the base comparison. Any address less than the value programmed in this field is unaffected by this protected range. 747 Serial Peripheral Interface (SPI) 21.4.12 PR1--Protected Range 1 Register (GbE LAN Memory Mapped Configuration Registers) Memory Address: MBARB + 78h Default Value: 00000000h Note: 31 30:29 28:16 15 14:13 12:0 Description Write Protection Enable--R/W. When set, this bit indicates that the Base and Limit fields in this register are valid and that writes and erases directed to addresses between them (inclusive) must be blocked by hardware. The base and limit fields are ignored when this bit is cleared. Reserved Protected Range Limit--R/W. This field corresponds to FLA address bits 24:12 and specifies the upper limit of the protected range. Address bits 11:0 are assumed to be FFFh for the limit comparison. Any address greater than the value programmed in this field is unaffected by this protected range. Read Protection Enable--R/W. When set, this bit indicates that the Base and Limit fields in this register are valid and that read directed to addresses between them (inclusive) must be blocked by hardware. The base and limit fields are ignored when this bit is cleared. Reserved Protected Range Base--R/W. This field corresponds to FLA address bits 24:12 and specifies the lower base of the protected range. Address bits 11:0 are assumed to be 000h for the base comparison. Any address less than the value programmed in this field is unaffected by this protected range. SSFS--Software Sequencing Flash Status Register (GbE LAN Memory Mapped Configuration Registers) Memory Address: MBARB + 90h Default Value: 00h Note: Attribute: Size: RO, R/WC 8 bits The Software Sequencing control and status registers are reserved if the hardware sequencing control and status registers are used. Bit 7:5 748 R/W 32 bits This register can not be written when the FLOCKDN bit is set to 1. Bit 21.4.13 Attribute: Size: Description Reserved 4 Access Error Log (AEL)--RO. This bit reflects the value of the Hardware Sequencing Status AEL register. 3 Flash Cycle Error (FCERR)--R/WC. Hardware sets this bit to 1 when a programmed access is blocked from running on the SPI interface due to one of the protection policies or when any of the programmed cycle registers is written while a programmed access is already in progress. This bit remains asserted until cleared by software writing a 1 or hardware reset due to a global reset or host partition reset in an Intel ME enabled system. 2 Cycle Done Status--R/WC. The PCH sets this bit to 1 when the SPI Cycle completes (that is, SCIP bit is 0) after software sets the GO bit. This bit remains asserted until cleared by software writing a 1 or hardware reset due to a global reset or host partition reset in an Intel ME enabled system. When this bit is set and the SPI SMI# Enable bit is set, an internal signal is asserted to the SMI# generation block. Software must make sure this bit is cleared prior to enabling the SPI SMI# assertion for a new programmed access. 1 Reserved 0 SPI Cycle In Progress (SCIP)--RO. Hardware sets this bit when software sets the SPI Cycle Go bit in the Command register. This bit remains set until the cycle completes on the SPI interface. Hardware automatically sets and clears this bit so that software can determine when read data is valid and/or when it is safe to begin programming the next command. Software must only program the next command when this bit is 0. Datasheet Serial Peripheral Interface (SPI) 21.4.14 SSFC--Software Sequencing Flash Control Register (GbE LAN Memory Mapped Configuration Registers) Memory Address: MBARB + 91h Default Value: 000000h Bit R/W 24 bits Description 23:19 Reserved 18:16 SPI Cycle Frequency (SCF)--R/W. This register sets frequency to use for all SPI software sequencing cycles (write, erase, fast read, read status, and so on) except for the read cycle which always run at 20 MHz. 000 = 20 MHz 001 = 33 MHz All other values = Reserved. This register is locked when the SPI Configuration Lock-Down bit is set. 15 Reserved 14 Data Cycle (DS)--R/W. When set to 1, there is data that corresponds to this transaction. When 0, no data is delivered for this cycle, and the dBC and data fields themselves are don't cares. 13:8 Data Byte Count (dBC)--R/W. This field specifies the number of bytes to shift in or out during the data portion of the SPI cycle. The valid settings (in decimal) are any value from 0 to 3. The number of bytes transferred is the value of this field plus 1. When this field is 00b, then there is 1 byte to transfer and that 11b means there are 4 bytes to transfer. 7 Datasheet Attribute: Size: Reserved 6:4 Cycle Opcode Pointer (COP)--R/W. This field selects one of the programmed opcodes in the Opcode Menu to be used as the SPI Command/Opcode. In the case of an Atomic Cycle Sequence, this determines the second command. 3 Sequence Prefix Opcode Pointer (SPOP)--R/W. This field selects one of the two programmed prefix opcodes for use when performing an Atomic Cycle Sequence. A value of 0 points to the opcode in the least significant byte of the Prefix Opcodes register. By making this programmable, the PCH supports flash devices that have different opcodes for enabling writes to the data space versus status register. 2 Atomic Cycle Sequence (ACS)--R/W. When set to 1 along with the SCGO assertion, the PCH will execute a sequence of commands on the SPI interface without allowing the LAN component to arbitrate and interleave cycles. The sequence is composed of: * Atomic Sequence Prefix Command (8-bit opcode only) * Primary Command specified below by software (can include address and data) * Polling the Flash Status Register (opcode 05h) until bit 0 becomes 0b. The SPI Cycle in Progress bit remains set and the Cycle Done Status bit remains unset until the Busy bit in the Flash Status Register returns 0. 1 SPI Cycle Go (SCGO)--R/WS. This bit always returns 0 on reads. However, a write to this register with a `1' in this bit starts the SPI cycle defined by the other bits of this register. The "SPI Cycle in Progress" (SCIP) bit gets set by this action. Hardware must ignore writes to this bit while the Cycle In Progress bit is set. Hardware allows other bits in this register to be programmed for the same transaction when writing this bit to 1. This saves an additional memory write. 0 Reserved 749 Serial Peripheral Interface (SPI) 21.4.15 PREOP--Prefix Opcode Configuration Register (GbE LAN Memory Mapped Configuration Registers) Memory Address: MBARB + 94h Default Value: 0000h R/W 16 bits Bit Description 15:8 Prefix Opcode 1--R/W. Software programs an SPI opcode into this field that is permitted to run as the first command in an atomic cycle sequence. 7:0 Prefix Opcode 0--R/W. Software programs an SPI opcode into this field that is permitted to run as the first command in an atomic cycle sequence. Note: 21.4.16 Attribute: Size: This register is not writable when the SPI Configuration Lock-Down bit (MBARB + 00h:15) is set. OPTYPE--Opcode Type Configuration Register (GbE LAN Memory Mapped Configuration Registers) Memory Address: MBARB + 96h Default Value: 0000h Attribute: Size: R/W 16 bits Entries in this register correspond to the entries in the Opcode Menu Configuration register. Note: The definition below only provides write protection for opcodes that have addresses associated with them. Therefore, any erase or write opcodes that do not use an address should be avoided (for example, "Chip Erase" and "Auto-Address Increment Byte Program"). Bit 15:14 Opcode Type 7--R/W. See the description for bits 1:0 13:12 Opcode Type 6--R/W. See the description for bits 1:0 11:10 Opcode Type 5--R/W. See the description for bits 1:0 9:8 Opcode Type 4--R/W. See the description for bits 1:0 7:6 Opcode Type 3--R/W. See the description for bits 1:0 5:4 Opcode Type 2--R/W. See the description for bits 1:0 3:2 Opcode Type 1--R/W. See the description for bits 1:0 1:0 Opcode Type 0--R/W. This field specifies information about the corresponding Opcode 0. This information allows the hardware to 1) know whether to use the address field and 2) provide BIOS and Shared Flash protection capabilities. The encoding of the two bits is: 00 = No address associated with this Opcode; Read cycle type 01 = No address associated with this Opcode; Write cycle type 10 = Address required; Read cycle type 11 = Address required; Write cycle type Note: 750 Description This register is not writable when the SPI Configuration Lock-Down bit (MBARB + 00h:15) is set. Datasheet Serial Peripheral Interface (SPI) 21.4.17 OPMENU--Opcode Menu Configuration Register (GbE LAN Memory Mapped Configuration Registers) Memory Address: MBARB + 98h Default Value: 0000000000000000h Attribute: Size: R/W 64 bits Eight entries are available in this register to give GbE a sufficient set of commands for communicating with the flash device, while also restricting what malicious software can do. This keeps the hardware flexible enough to operate with a wide variety of SPI devices. Note: It is recommended that GbE avoid programming Write Enable opcodes in this menu. Malicious software could then perform writes and erases to the SPI flash without using the atomic cycle mechanism. This could cause functional failures in a shared flash environment. Write Enable opcodes should only be programmed in the Prefix Opcodes. Bit Description 63:56 Allowable Opcode 7--R/W. See the description for bits 7:0 55:48 Allowable Opcode 6--R/W. See the description for bits 7:0 47:40 Allowable Opcode 5--R/W. See the description for bits 7:0 39:32 Allowable Opcode 4--R/W. See the description for bits 7:0 31:24 Allowable Opcode 3--R/W. See the description for bits 7:0 23:16 Allowable Opcode 2--R/W. See the description for bits 7:0 15:8 Allowable Opcode 1--R/W. See the description for bits 7:0 7:0 Allowable Opcode 0--R/W. Software programs an SPI opcode into this field for use when initiating SPI commands through the Control Register. This register is not writable when the SPI Configuration Lock-Down bit (MBARB + 00h:15) is set. Datasheet 751 Thermal Sensor Registers (D31:F6) 22 Thermal Sensor Registers (D31:F6) 22.1 PCI Bus Configuration Registers Table 22-1. Thermal Sensor Register Address Map Offset 22.1.1 Mnemonic Register Name Attribute 00h-01h VID Vendor Identification 8086h RO 02h-03h DID Device Identification 3A32h RO 04h-05h CMD Command Register 0000h R/W, RO 06h-07h STS Device Status 0010h R/WC, RO 08h RID Revision ID 00h RO 09h PI Programming Interface 00h RO 0Ah SCC Sub Class Code 80h RO 0Bh BCC Base Class Code 11h RO 0Ch CLS 0Dh LT Cache Line Size 00h RO Latency Timer 00h RO 0Eh HTYPE Header Type 00h RO 10h-13h TBAR Thermal Base Address 00000004h R/W, RO 14h-17h TBARH Thermal Base Address High DWord 2Ch-2Dh SVID 2Eh-2Fh SID 34h CAP_PTR 00000000h RO Subsystem Vendor Identifier 0000h R/WO Subsystem Identifier 0000h R/WO 50h RO Capabilities Pointer 3Ch INTLN Interrupt Line 00h R/W 3Dh INTPN Interrupt Pin See Description RO 40h-43h TBARB BIOS Assigned Thermal Base Address 00000004h R/W, RO 44h-47h TBARBH BIOS Assigned Thermal Base High DWord 00000000h R/W 50h-51h PID PCI Power Management Capability ID 0001h RO 52h-53h PC Power Management Capabilities 0023h RO 54h-57h PCS Power Management Control and Status 0008h R/W, RO VID--Vendor Identification Register Offset Address: 00h-01h Default Value: 8086h Lockable: No Bit 15:0 752 Default Attribute: RO Size: 16 bit Power Well:Core Description Vendor ID--RO. This is a 16-bit value assigned to Intel. Intel VID = 8086h Datasheet Thermal Sensor Registers (D31:F6) 22.1.2 DID--Device Identification Register Offset Address: 02h-03h Default Value: 3A32h Bit 15:0 22.1.3 Attribute: Size: Description Device ID (DID)--RO. Indicates the device number assigned by the SIG. CMD--Command Register Address Offset: 04h-05h Default Value: 0000h Bit 15:11 10 22.1.4 Attribute: Size: RO, R/W 16 bits Description Reserved Interrupt Disable (ID)--R/W. Enables the device to assert an INTx#. 0 = When cleared, the INTx# signal may be asserted. 1 = When set, the Thermal logic's INTx# signal will be de-asserted. 9 FBE (Fast Back to Back Enable)--RO. Hardwired to 0. 8 SEN (SERR Enable)--RO. Hardwired to 0. 7 WCC (Wait Cycle Control)--RO. Hardwired to 0. 6 PER (Parity Error Response)--RO. Hardwired to 0. 5 VPS (VGA Palette Snoop)--RO. Hardwired to 0. 4 MWI (Memory Write and Invalidate Enable)--RO. Hardwired to 0. 3 SCE (Special Cycle Enable)--RO. Hardwired to 0. 2 BME (Bus Master Enable)--R/W. 0 = Function disabled as bus master. 1 = Function enabled as bus master. 1 Memory Space Enable (MSE)--R/W. 0 = Disable 1 = Enable. Enables memory space accesses to the Thermal registers. 0 IOS (I/O Space)--RO. The Thermal logic does not implement I/O Space; therefore, this bit is hardwired to 0. STS--Status Register Address Offset: 06h-07h Default Value: 0010h Datasheet RO 16 bits Attribute: Size: R/WC, RO 16 bits Bit Description 15 Detected Parity Error (DPE)--R/WC. This bit is set whenever a parity error is seen on the internal interface for this function, regardless of the setting of bit 6 in the command register. Software clears this bit by writing a 1 to this bit location. 14 SERR# Status (SERRS)--RO. Hardwired to 0. 13 Received Master Abort (RMA)--RO. Hardwired to 0. 12 Received Target Abort (RTA)--RO. Hardwired to 0. 11 Signaled Target-Abort (STA)--RO. Hardwired to 0. 10:9 DEVSEL# Timing Status (DEVT)--RO. Hardwired to 0. 8 Master Data Parity Error (MDPE)--RO. Hardwired to 0. 7 Fast Back to Back Capable (FBC)--RO. Hardwired to 0. 753 Thermal Sensor Registers (D31:F6) Bit 6 Reserved 5 66 MHz Capable (C66)--RO. Hardwired to 0. 4 Capabilities List Exists (CLIST)--RO. Indicates that the controller contains a capabilities pointer list. The first item is pointed to by looking at configuration offset 34h. 3 Interrupt Status (IS)--RO. Reflects the state of the INTx# signal at the input of the enable/ disable circuit. This bit is a 1 when the INTx# is asserted. This bit is a 0 after the interrupt is cleared (independent of the state of the Interrupt Disable bit in the command register). 2:0 22.1.5 Description Reserved RID--Revision Identification Register Address Offset: 08h Default Value: 00h Bit 7:0 22.1.6 Attribute: Size: Description Revision ID (RID)--RO. This field indicates the device specific revision identifier. PI--Programming Interface Register Address Offset: 09h Default Value: 00h Bit 7:0 22.1.7 Attribute: Size: Programming Interface (PI)--RO. The PCH Thermal logic has no standard programming interface. SCC--Sub Class Code Register Bit 7:0 Attribute: Size: Sub Class Code (SCC)--RO. Value assigned to the PCH Thermal logic. BCC--Base Class Code Register Bit 7:0 Attribute: Size: RO 8 bits Description Base Class Code (BCC)--RO. Value assigned to the PCH Thermal logic. CLS--Cache Line Size Register Address Offset: 0Ch Default Value: 00h Bit 7:0 754 RO 8 bits Description Address Offset: 0Bh Default Value: 11h 22.1.9 RO 8 bits Description Address Offset: 0Ah Default Value: 80h 22.1.8 RO 8 bits Attribute: Size: RO 8 bits Description Cache Line Size (CLS)--RO. Does not apply to PCI Bus Target-only devices. Datasheet Thermal Sensor Registers (D31:F6) 22.1.10 LT--Latency Timer Register Address Offset: 0Dh Default Value: 00h Bit 7:0 22.1.11 Attribute: Size: Description Latency Timer (LT)--RO. Does not apply to PCI Bus Target-only devices. HTYPE--Header Type Register Address Offset: 0Eh Default Value: 00h Attribute: Size: RO 8 bits Bit Description 7 Multi-Function Device (MFD)--RO. This bit is 0 because a multi-function device only needs to be marked as such in Function 0, and the Thermal registers are not in Function 0. 6:0 22.1.12 RO 8 bits Header Type (HTYPE)--RO. Implements Type 0 Configuration header. TBAR--Thermal Base Register Address Offset: 10h-13h Default Value: 00000004h Attribute: Size: R/W, RO 32 bits This BAR creates 4K bytes of memory space to signify the base address of Thermal memory mapped configuration registers. This memory space is active when the Command (CMD) register Memory Space Enable (MSE) bit is set and either TBAR[31:12] or TBARH are programmed to a non-zero address. This BAR is owned by the Operating System, and allows the OS to locate the Thermal registers in system memory space. Bit 31:12 11:4 3 2:1 0 22.1.13 Description Thermal Base Address (TBA)--R/W. This field provides the base address for the Thermal logic memory mapped configuration registers. 4 KB bytes are requested by hardwiring bits 11:4 to 0s. Reserved Prefetchable (PREF)--RO. Indicates that this BAR is NOT prefetchable. Address Range (ADDRNG)--RO. Indicates that this BAR can be located anywhere in 64-bit address space. Space Type (SPTYP)--RO. Indicates that this BAR is located in memory space. TBARH--Thermal Base High DWord Register Address Offset: 14h-17h Default Value: 00000000h Attribute: Size: R/W, RO 32 bits This BAR extension holds the high 32 bits of the 64-bit TBAR. In conjunction with TBAR, it creates 4 KB of memory space to signify the base address of Thermal memory mapped configuration registers. Bit 31:0 Datasheet Description Thermal Base Address High (TBAH)--R/W. TBAR bits 61:32. 755 Thermal Sensor Registers (D31:F6) 22.1.14 SVID--Subsystem Vendor ID Register Address Offset: 2Ch-2Dh Default Value: 0000h Attribute: Size: R/WO 16 bits This register should be implemented for any function that could be instantiated more than once in a given system. The SVID register, in combination with the Subsystem ID register, enables the operating environment to distinguish one subsystem from the other(s). Software (BIOS) will write the value to this register. After that, the value can be read, but writes to the register will have no effect. The write to this register should be combined with the write to the SID to create one 32-bit write. This register is not affected by D3HOT to D0 reset. Bit 15:0 22.1.15 Description SVID (SVID)--R/WO. These R/WO bits have no PCH functionality. SID--Subsystem ID Register Address Offset: 2Eh-2Fh Default Value: 0000h Attribute: Size: R/WO 16 bits This register should be implemented for any function that could be instantiated more than once in a given system. The SID register, in combination with the Subsystem Vendor ID register make it possible for the operating environment to distinguish one subsystem from the other(s). Software (BIOS) will write the value to this register. After that, the value can be read, but writes to the register will have no effect. The write to this register should be combined with the write to the SVID to create one 32-bit write. This register is not affected by D3HOT to D0 reset. Bit 15:0 22.1.16 Description SID (SAID)--R/WO. These R/WO bits have no PCH functionality. CAP_PTR--Capabilities Pointer Register Address Offset: 34h Default Value: 50h 22.1.17 Attribute: Size: Bit Description 7:0 Capability Pointer (CP)--RO. Indicates that the first capability pointer offset is offset 50h (Power Management Capability). INTLN--Interrupt Line Register Address Offset: 3Ch Default Value: 00h 756 RO 8 bits Attribute: Size: R/W 8 bits Bit Description 7:0 Interrupt Line--R/W. PCH hardware does not use this field directly. It is used to communicate to software the interrupt line that the interrupt pin is connected to. Datasheet Thermal Sensor Registers (D31:F6) 22.1.18 INTPN--Interrupt Pin Register Address Offset: 3Dh Default Value: See description Bit 22.1.19 Attribute: Size: RO 8 bits Description 7:4 Reserved 3:0 Interrupt Pin--RO. This reflects the value of the Device 31 interrupt pin bits 27:24 (TTIP) in chipset configuration space. TBARB--BIOS Assigned Thermal Base Address Register Address Offset: 40h-43h Default Value: 00000004h Attribute: Size: R/W, RO 32 bits This BAR creates 4 KB of memory space to signify the base address of Thermal memory mapped configuration registers. This memory space is active when TBARB.SPTYPEN is asserted. This BAR is owned by the BIOS, and allows the BIOS to locate the Thermal registers in system memory space. If both TBAR and TBARB are programmed, then the OS and BIOS each have their own independent "view" of the Thermal registers, and must use the TSIU register to denote Thermal registers ownership/availability. Bit 31:12 11:4 3 2:1 0 22.1.20 Description Thermal Base Address (TBA)--R/W. This field provides the base address for the Thermal logic memory mapped configuration registers. 4K B bytes are requested by hardwiring bits 11:4 to 0s. Reserved Prefetchable (PREF)--RO. Indicates that this BAR is NOT prefetchable. Address Range (ADDRNG)--RO. Indicates that this BAR can be located anywhere in 64-bit address space. Space Type Enable (SPTYPEN)--R/W. 0 = Disable. 1 = Enable. When set to 1b by software, enables the decode of this memory BAR. TBARBH--BIOS Assigned Thermal Base High DWord Register Address Offset: 44h-47h Default Value: 00000000h Attribute: Size: R/W 32 bits This BAR extension holds the high 32 bits of the 64-bit TBARB. Bit 31:0 22.1.21 Description Thermal Base Address High (TBAH)--R/W. TBAR bits 61:32. PID--PCI Power Management Capability ID Register Address Offset: 50h-51h Default Value: 0001h Bit 15:8 7:0 Datasheet Attribute: Size: RO 16 bits Description Next Capability (NEXT)--RO. Indicates that this is the last capability structure in the list. Cap ID (CAP)--RO. Indicates that this pointer is a PCI power management capability 757 Thermal Sensor Registers (D31:F6) 22.1.22 PC--Power Management Capabilities Register Address Offset: 52h-53h Default Value: 0023h Bit 15:11 PME_Support--RO. Indicates PME# is not supported D2_Support--RO. The D2 state is not supported. 9 D1_Support--RO. The D1 state is not supported. Aux_Current--RO. PME# from D3COLD state is not supported, therefore this field is 000b. 5 Device Specific Initialization (DSI)--RO. Indicates that device-specific initialization is required. 4 Reserved 3 2:0 PME Clock (PMEC)--RO. Does not apply. Hardwired to 0. Version (VS)--RO. Indicates support for Revision 1.2 of the PCI Power Management Specification. PCS--Power Management Control And Status Register Address Offset: 54h-57h Default Value: 0008h Bit 31:24 Attribute: Size: Description Bus Power/Clock Control Enable (BPCCE)--RO. Hardwired to 0. 22 B2/B3 Support (B23)--RO. Does not apply. Hardwired to 0. 15 14:9 8 7:4 3 2 1:0 R/W, RO 32 bits Data--RO. Does not apply. Hardwired to 0s. 23 21:16 758 RO 16 bits Description 10 8:6 22.1.23 Attribute: Size: Reserved PME Status (PMES)--RO. This bit is always 0, since this PCI Function does not generate PME#. Reserved PME Enable (PMEE)--RO. This bit is always zero, since this PCI Function does not generate PME#. Reserved No Soft Reset--RO. When set 1, this bit indicates that devices transitioning from D3HOT to D0 because of PowerState commands do not perform an internal reset. Configuration context is preserved. Upon transition from D3HOT to D0 initialized state, no additional operating system intervention is required to preserve Configuration Context beyond writing the PowerState bits. Reserved Power State (PS)--R/W. This field is used both to determine the current power state of the Thermal controller and to set a new power state. The values are: 00 = D0 state 11 = D3HOT state If software attempts to write a value of 10b or 01b in to this field, the write operation must complete normally; however, the data is discarded and no state change occurs. When in the D3HOT states, the Thermal controller's configuration space is available, but the I/O and memory spaces are not. Additionally, interrupts are blocked. When software changes this value from the D3HOT state to the D0 state, no internal warm (soft) reset is generated. Datasheet Thermal Sensor Registers (D31:F6) 22.2 Thermal Memory Mapped Configuration Registers (Thermal Sensor - D31:F26) The base memory for these thermal memory mapped configuration registers is specified in the TBARB (D31:F6:Offset 40h) register. The individual registers are then accessible at TBARB + Offset. All registers in Table 22-1 are located in the Core Well. Table 22-1. Thermal Memory Mapped Configuration Register Address Map 22.2.1 Offset Mnemonic 00h-01h TEMP 04h TSC Thermal Sensor Control 00h RO, R/W 06h TSS Thermal Sensor Status 00h RO, R/W, R/WC Temperature Default Attribute 0000h RO 08h TSEL Thermal Sensor Enable and Lock 00h RO, R/W 0Ah TSREL Thermal Sensor Report Enable and Lock 00h RO, R/W Thermal Sensor SMI Control 0Ch TSMIC 10h-11h CTT 14h-15h 18h-19h 00h RO, R/W Catastrophic Trip Point 01FFh RO, R/W TAHV Thermal Alert High Value 0000h RO, R/W TALV Thermal Alert Low Value 0000h RO, R/W 40h-43h TL Throttle Levels 00000000h RO, R/W 60h-61h PHL PCH Hot Level 0000h RO, R/W 62h PHLC 80h TAS PHL Control 00h RO, R/W Thermal Alert Status 00h RO, R/W, R/WC 82h TSPIEN PCI Interrupt Event Enables 00h RO, R/W 84h TSGPEN General Purpose Event Enables 00h RO, R/W TEMP--Temperature Register Offset Address: Default Value: Bit 15:9 8:0 Datasheet Register Name TBARB+00h 0000h Attribute: Size: RO 16 bit Description Reserved TS Reading (TSR)--RO. The die temperature with resolution of 1/2 degree C and an offset of -50 C. Thus, a reading of 0x121 is 94.5C. 759 Thermal Sensor Registers (D31:F6) 22.2.2 TSC--Thermal Sensor Control Register Offset Address: Default Value: TBARB+04h 00h Attribute: Size: RO, R/W 8 bit This register controls the operation of the thermal sensor. Bit Description 7 Policy Lock-Down Bit--R/W. When written to 1, this bit prevents any more writes to the register (offset 04h) and to CTT (offset 10h) 6:1 0 22.2.3 Reserved Catastrophic Power-Down Enable--R/W. When set to 1, the power management logic (PMC) transitions to the S5 state when a catastrophic temperature is detected by the sensor. The transition to the S5 state must be unconditional (like the Power Button Override Function). The thermal sensor and response logic is in the core/main power well; therefore, detection of a catastrophic temperature is limited to times when this well is powered and out of reset. TSS--Thermal Sensor Status Register Offset Address: Default Value: TBARB+06h 00h Attribute: Size: RO, R/W 8 bit This register provides statuses of the thermal sensor. Bit 7:5 Description Reserved 4 Thermal Sensor Dynamic Shutdown Status (TSDSS)--RO. This bit indicates the status of the thermal sensor circuit when TSEL.ETS=1. 1 = thermal sensor is fully operational 0 = thermal sensor is in a dynamic shutdown state 3 GPE Status (GPES)--R/WC. Set when GPE is enabled for a trip event. Software must write a `1' to this bit to clear the GPE status. GPE can be configured to cause an SMI or SCI. As long as this bit is set, the GPE indication to the global GPE logic is asserted. 2 1:0 22.2.4 SMI Status (SMIS)--R/WC. Set when SMI is enabled for a trip event. Software must write a `1' to this bit to clear the SMI status. As long as this bit is set, the SMI indication to the global SMI logic is asserted. Reserved TSEL--Thermal Sensor Enable and Lock Register Offset Address: Default Value: TBARB+08h 00h Attribute: Size: RO, R/W 8 bit This register controls the operation of the thermal sensor. Bit 7 6:1 0 760 Description Policy Lock-Down Bit--R/W. When written to 1, this bit prevents any more writes to this register. Reserved Enable TS (ETS)--R/W. 1 = Enables the thermal sensor. Until this bit is set, no thermometer readings or trip events will occur. If SW reads the TEMP register before the sensor is enabled, it will read 0x0. The value of this bit is sent to the thermal sensor. NOTE: if the sensor is running and valid temperatures have been captured in TEMP and then ETS is cleared, TEMP will retain its old value. Clearing ETS does not force TEMP to 0x00. 0 = Disables the sensor. Datasheet Thermal Sensor Registers (D31:F6) 22.2.5 TSREL--Thermal Sensor Reporting Enable and Lock Register Offset Address: TBARB+0Ah Default Value: 00h Description 7 Policy Lock-Down Bit--R/W. When written to 1, this bit prevents anymore writes to this register. 0 Reserved Enable SMBus Temperature Reporting--R/W. 1 = Enables the reporting of the PCH temperature to the SMBus and PMC. This must also be set if ME needs access to the PCH temperature. Once enabled this bit should not be cleared by software. If it is cleared then the EC may get an undefined value. Software has no need to dynamically disable and then re-enable this bit. 0 = Disables temperature reporting. TSMIC--Thermal Sensor SMI Control Register Offset Address: Default Value: TBARB+0Ch 00h Attribute: Size: Description 7 Policy Lock-Down Bit--R/W. When written to 1, this bit prevents anymore writes to this register. 0 Reserved SMI Enable on Alert Thermal Sensor Trip--R/W. 1 = Enables SMI# assertions on alert thermal sensor events for either low-to-high or high-to-low events. Both edges are enabled by this one bit. 0 = Disables SMI# assertions for alert thermal events. CTT--Catastrophic Trip Point Register Offset Address: TBARB+10h Default Value: 01FFh Bit 15:9 8:0 22.2.8 RO, R/W 8 bit Bit 6:1 22.2.7 RO, R/W 8 bit Bit 6:1 22.2.6 Attribute: Size: Attribute: Size: RO, R/W 16 bit Description Reserved Catastrophic Temperature TRIP (CTRIP)--R/W. When the current temperature reading is greater than or equal to the value in this register, a catastrophic trip event is signaled. This register is locked by TSC[7] TAHV--Thermal Alert High Value Register Offset Address: Default Value: Bit 15:9 8:0 TBARB+14h 0000h Attribute: Size: RO, R/W 16 bit Description Reserved Alert High (AH)--R/W. Sets the high value for the alert indication. See the later section for usage. Note: It is illegal for SW to program AH to a value less than TALV.AL. This register is not lockable, so that SW can change the values during runtime. Datasheet 761 Thermal Sensor Registers (D31:F6) 22.2.9 TALV--Thermal Alert Low Value Register Offset Address: TBARB+18h Default Value: 0000h Bit 15:9 8:0 22.2.10 Attribute: Size: R/W, RO 16 bit Description Reserved Alert Low (AL)--R/W. Sets the low value for the alert indication. See the later section for usage. This register is not lockable, so that SW can change the values during runtime. TL--Throttle Levels Register Offset Address: TBARB+40h Default Value: 00000000h Attribute: Size: RO, R/W 32 bit Bit Description 31 TT.Lock - R/W. When set to `1', this entire register (TL) is locked and remains locked until the next platform reset. 30 TT.State13 Enable (TT13EN) - R/W. When set to `1' and the programmed GPIO pin is a `1', then PMSync state 13 will force at least T2 state. 29 TT Enable (TTEN) - R/W. When set the thermal throttling states are enabled. At reset, BIOS must set bits 28:0 and then do a separate write to set bit 29 to enable throttling. SW may set bit 31 at the same time it sets bit 29 if it wishes to lock the register. If SW wishes to change the values of 28:0, it must first clear the TTEN bit, then change the values in 28:0; and then re-enable TTEN. It is legal to set bits 31, 30 and 29 with the same write. This bit must not be set by SW until SW has already enabled the thermal sensor(TSEL.ETS ='1'). If TTEN is written to `0', after having been enabled, then the PCH may stay in the throttling state it was in at the moment TTEN is disabled. There is no intent that the sensor be enabled for a while and then disabled and left off. It may be disabled temporarily while changing the register values, but it should not be left in the disabled state. 28:20 T2 Level (T2L) - R/W. When TTEN = 1 AND TSE = `1' AND (T2L >= TSR[8:0] > T1L), then the system is in T2 state. When TTEN = 1 AND TSE = `1' AND (TSR[8:0] > T2L), then the system is in T3 state. Note: The T3 condition overrides PMSync[13] and forces the system to T3 if both cases are true. SW NOTE:T2L must be programmed to a value greater than T1L if TTEN='1' 19 18:10 Reserved T1 Level (T1L) - R/W. When TTEN = 1 AND TSE = 1 AND (T1L >= TSR[8:0] > T0L), then the system is in T1 state. SW NOTE:T1L must be programmed to a value greater than T0L if TTEN='1' 9 8:0 762 Reserved T0 Level (T0L) - R/W. When TEMP.TSR[8:0] <= T0L OR TT.Enable is `0' OR TSE 0', then the system is in T0 state. Datasheet Thermal Sensor Registers (D31:F6) 22.2.11 PHL--PCH Hot Level Register Offset Address: TBARB+60h Default Value: 0000h Bit 15 14:9 8:0 22.2.12 Attribute: Size: Description PHL Enable (PHLE) - R/W. When set and the current temperature reading, TSR, is greater than PHLL, then the TEMP_ALERT# pin will be asserted (active low). Reserved PHL Level (PHLL) - R/W. Temperature value used for TEMP_ALERT# pin. PHLC--PHL Control Register Offset Address: TBARB+62h Default Value: 00h Bit 7:1 0 22.2.13 RO, R/W 16 bit Attribute: Size: RO, R/W 8 bit Description Reserved PHL Lock - R/W. When written to a `1', then both PHL and PHLC are locked TAS--Thermal Alert Status Register Offset Address: TBARB+80h Default Value: 00h Bit 7:2 Attribute: Size: RO, R/W 8 bit Description Reserved 1 Alert High-to-Low Event (AHLE)--R/WC. 1 = Indicates that a Hot Thermal Sensor trip event occurred based on a lower to higher temperature transition thru the trip point. 0 = No trip for this event Software must write a 1 to clear this status bit. 0 Alert Low-to-High Event (ALHE)--R/WC. 1 = Indicates that an Aux Thermal Sensor trip event occurred based on a lower to higher temperature transition thru the trip point. 0 = No trip for this event Software must write a 1 to clear this status bit. Note: AHLE will not be set until there has been one occurrence of a Low to High event (ALHE must have been set once). This prevents the case where the system power up at a reasonably high temperature and starts to cool off while booting and causing an interrupt before there is SW loaded to handle it. 22.2.14 TSPIEN--PCI Interrupt Event Enables Register Offset Address: TBARB+82h Default Value: 00h Bit 7:2 Datasheet Attribute: Size: RO, R/W 8 bit Description Reserved 1 Alert High-to-Low Enable--R/W. When set to 1, the thermal sensor logic asserts the Thermal logic PCI INTx signal when the corresponding status bit is set in the Thermal Error Status register. When cleared, the corresponding status bit does not result in PCI INTx. 0 Alert Low-to-High Enable--R/W. See the description for bit 1 763 Thermal Sensor Registers (D31:F6) 22.2.15 TSGPEN--General Purpose Event Enables Register Offset Address: TBARB+84h Default Value: 00h Bit 7:2 1 Attribute: Size: RO, R/W 8 bit Description Reserved Alert High-to-Low Enable--R/W. When set to 1, the thermal sensor logic asserts its General Purpose Event signal to the GPE block when the corresponding status bit is set in the Thermal Error Status register. When cleared, the corresponding status bit does not result in the GPE signal assertion. Alert Low-to-High Enable--R/W. See the description for bit 1. 764 Datasheet Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23 Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.1 First Intel(R) Management Engine Interface (Intel(R) MEI) Configuration Registers (Intel(R) MEI 1--D22:F0) 23.1.1 PCI Configuration Registers (Intel(R) MEI 1--D22:F0) Table 23-1. Intel(R) MEI 1 Configuration Registers Address Map (Intel(R) MEI 1--D22:F0) (Sheet 1 of 2) / Offset Datasheet Mnemonic Register Name Default Attribute 00h-01h VID Vendor Identification 8086h RO 02h-03h DID Device Identification See register description RO 04h-05h PCICMD PCI Command 0000h R/W, RO 06h-07h PCISTS PCI Status 0010h RO 08h RID Revision Identification See register description RO 09h-0Bh CC Class Code 078000h RO 0Eh HTYPE 10h-17h MEI0_MBAR Header Type 80h RO 00000000000 00004h R/W, RO 2Ch-2Dh SVID 2Eh-2Fh SID Subsystem Vendor ID 0000h R/WO Subsystem ID 0000h R/WO 34h CAPP Capabilities List Pointer 3Ch-3Dh INTR Interrupt Information Intel MEI 1 MMIO Base Address 50h RO 0100h R/W, RO 40h-43h HFSTS1 Host Firmware Status Register #1 00000000h RO 44h-47h ME_UMA Management Engine UMA Register 10000000h RO 48h-4Bh HFSTS2 Host Firmware Status Register #2 00000000h RO 4Ch-4Fh H_GS Host General Status 00000000h R/W 50h-51h PID PCI Power Management Capability ID 8C01h RO 52h-53h PC PCI Power Management Capabilities C803h RO 54h-55h PMCS PCI Power Management Control and Status 0008h R/WC, R/W, RO 60h-63h HFSTS3 Host Firmware Status Register #3 00000000h RO 64h-67h HFSTS4 Host Firmware Status Register #4 00000000h RO 68h-6Bh HFSTS5 Host Firmware Status Register #5 00000000h RO 6Ch-6Fh HFSTS6 Host Firmware Status Register #6 00000000h RO 70h-73h H_GS2 Host General Status 2 00000000h RW 74h-77h H_GS3 Host General Status 3 00000000h RW 765 Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) Table 23-1. Intel(R) MEI 1 Configuration Registers Address Map (Intel(R) MEI 1--D22:F0) (Sheet 2 of 2) 23.1.1.1 Offset Mnemonic Register Name 8Ch-8Dh MID Message Signaled Interrupt Identifiers 0005h RO 8Eh-8Fh MC Message Signaled Interrupt Message Control 0080h R/W, RO MA Message Signaled Interrupt Message Address 00000000h R/W, RO 94h-97h MUA Message Signaled Interrupt Upper Address 00000000h R/W 98h-99h MD Message Signaled Interrupt Message Data 0000h R/W A0h HIDM BCh-BFh HERES C0h-DFh HER[1:8] 00h R/W Intel MEI Extended Register Status Intel MEI Interrupt Delivery Mode 40000000h RO Intel MEI Extended Register DW[1:8] 00000000h RO VID--Vendor Identification Register (Intel(R) MEI 1--D22:F0) Bit 15:0 Attribute: Size: RO 16 bits Description Vendor ID (VID)--RO. This is a 16-bit value assigned to Intel. DID--Device Identification Register (Intel(R) MEI 1--D22:F0) Address Offset: 02h-03h Default Value: See bit description Bit 15:0 23.1.1.3 Attribute 90h-93h Address Offset: 00h-01h Default Value: 8086h 23.1.1.2 Default Attribute: Size: RO 16 bits Description Device ID (DID)--RO. This is a 16-bit value assigned to the Intel Management Engine Interface controller. See Section 1.3 for the value of the DID Register. PCICMD--PCI Command Register (Intel(R) MEI 1--D22:F0) Address Offset: 04h-05h Default Value: 0000h Bit 15:11 Attribute: Size: R/W, RO 16 bits Description Reserved 10 Interrupt Disable (ID)--R/W. Disables this device from generating PCI line based interrupts. This bit does not have any effect on MSI operation. 9:3 Reserved 2 Bus Master Enable (BME)--R/W. Controls the Intel MEI host controller's ability to act as a system memory master for data transfers. When this bit is cleared, Intel ME bus master activity stops and any active DMA engines return to an idle condition. This bit is made visible to firmware through the H_PCI_CSR register, and changes to this bit may be configured by the H_PCI_CSR register to generate an Intel ME MSI. When this bit is 0, Intel MEI is blocked from generating MSI to the host processor. Note: This bit does not block Intel MEI accesses to Intel ME UMA; that is, writes or reads to the host and Intel ME circular buffers through the read window and write window registers still cause Intel ME backbone transactions to Intel ME UMA. 766 Datasheet Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) Bit 23.1.1.4 Description 1 Memory Space Enable (MSE)--R/W. Controls access to the Intel ME memory mapped register space. 0 = Disable. Memory cycles within the range specified by the memory base and limit registers are master aborted. 1 = Enable. Allows memory cycles within the range specified by the memory base and limit registers accepted. 0 Reserved PCISTS--PCI Status Register (Intel(R) MEI 1--D22:F0) Address Offset: 06h-07h Default Value: 0010h Bit 15:5 Attribute: Size: RO 16 bits Description Reserved 4 Capabilities List (CL)--RO. Indicates the presence of a capabilities list, hardwired to 1. 3 Interrupt Status (IS)--RO. Indicates the interrupt status of the device. 0 = Interrupt is de-asserted. 1 = Interrupt is asserted. 2:0 23.1.1.5 Reserved RID--Revision Identification Register (Intel(R) MEI 1--D22:F0) Offset Address: 08h Default Value: See bit description 23.1.1.6 Attribute: Size: Bit Description 7:0 Revision ID--RO. This field indicates the device specific revision identifier. See Section 1.3 for the value of the RID Register. CC--Class Code Register (Intel(R) MEI 1--D22:F0) Address Offset: 09h-0Bh Default Value: 078000h Bit 23:16 15:8 7:0 Datasheet RO 8 bits Attribute: Size: RO 24 bits Description Base Class Code (BCC)--RO. Indicates the base class code of the Intel MEI device. Sub Class Code (SCC)--RO. Indicates the sub class code of the Intel MEI device. Programming Interface (PI)--RO. Indicates the programming interface of the Intel MEI device. 767 Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.1.1.7 HTYPE--Header Type Register (Intel(R) MEI 1--D22:F0) Address Offset: 0Eh Default Value: 80h Bit 7 6:0 23.1.1.8 Attribute: Size: RO 8 bits Description Multi-Function Device (MFD)--RO. Indicates the Intel MEI host controller is part of a multifunction device. Header Layout (HL)--RO. Indicates that the Intel MEI uses a target device layout. MEI0_MBAR--Intel(R) MEI 1 MMIO Base Address (Intel(R) MEI 1--D22:F0) Address Offset: 10h-17h Default Value: 0000000000000004h Attribute: Size: R/W, RO 64 bits This register allocates space for the MEI0 memory mapped registers. Bit 63:4 3 2:1 0 23.1.1.9 Description Base Address (BA)--R/W. Software programs this field with the base address of this region. Prefetchable Memory (PM)--RO. Indicates that this range is not prefetchable. Type (TP)--RO. Set to 10b to indicate that this range can be mapped anywhere in 64-bit address space. Resource Type Indicator (RTE)--RO. Indicates a request for register memory space. SVID--Subsystem Vendor ID Register (Intel(R) MEI 1--D22:F0) Address Offset: 2Ch-2Dh Default Value: 0000h Bit 15:0 23.1.1.10 Attribute: Size: Description Subsystem Vendor ID (SSVID)--R/WO. Indicates the sub-system vendor identifier. This field should be programmed by BIOS during boot-up. Once written, this register becomes Read Only. This field can only be cleared by PLTRST#. Note: Register must be written as a Word write or as a DWord write with SID register. SID--Subsystem ID Register (Intel(R) MEI 1--D22:F0) Address Offset: 2Eh-2Fh Default Value: 0000h 768 R/WO 16 bits Attribute: Size: R/WO 16 bits Bit Description 15:0 Subsystem ID (SSID)--R/WO. Indicates the sub-system identifier. This field should be programmed by BIOS during boot-up. Once written, this register becomes Read Only. This field can only be cleared by PLTRST#. Note: Register must be written as a Word write or as a DWord write with SVID register. Datasheet Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.1.1.11 CAPP--Capabilities List Pointer Register (Intel(R) MEI 1--D22:F0) Address Offset: 34h Default Value: 50h 23.1.1.12 Attribute: Size: Bit Description 7:0 Capabilities Pointer (PTR)--RO. Indicates that the pointer for the first entry in the capabilities list is at 50h in configuration space. INTR--Interrupt Information Register (Intel(R) MEI 1--D22:F0) Address Offset: 3Ch-3Dh Default Value: 0100h Bit 23.1.1.13 Attribute: Size: 15:8 Interrupt Pin (IPIN)--RO. This indicates the interrupt pin the Intel MEI host controller uses. A value of 1h/2h/3h/4h indicates that this function implements legacy interrupt on INTA/INTB/INTC/ INTD, respectively. 7:0 Interrupt Line (ILINE)--R/W. Software written value to indicate which interrupt line (vector) the interrupt is connected to. No hardware action is taken on this register. HFS--Host Firmware Status Register (Intel(R) MEI 1--D22:F0) Attribute: Size: RO 32 bits Bit Description 31:0 Host Firmware Status (HFS)--RO. This register field is used by Firmware to reflect the operating environment to the host. ME_UMA--Intel(R) Management Engine UMA Register (Intel(R) MEI 1--D22:F0) Address Offset: 44h-47h Default Value: 80000000h Bit 31 30:7 16 15:6 5:0 Datasheet R/W, RO 16 bits Description Address Offset: 40h-43h Default Value: 00000000h 23.1.1.14 RO 8 bits Attribute: Size: RO 32 bits Description Reserved--RO. Hardwired to 1. Can be used by host software to discover that this register is valid. Reserved Intel ME UMA Size Valid--RO. This bit indicates that FW has written to the MUSZ field. Reserved Intel ME UMA Size (MUSZ)--RO. This field reflect Intel ME Firmware's desired size of Intel ME UMA memory region. This field is set by Intel ME firmware prior to core power bring up allowing BIOS to initialize memory. 000000b = 0 MB, No memory allocated to Intel ME UMA 000001b = 1 MB 000010b = 2 MB 000100b = 4 MB 001000b = 8 MB 010000b = 16 MB 100000b = 32 MB 769 Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.1.1.15 GMES--General Intel(R) ME Status Register (Intel(R) MEI 1--D22:F0) Address Offset: 48h-4Bh Default Value: 00000000h Bit 31:0 23.1.1.16 Attribute: Size: Description General Intel ME Status (ME_GS)--RO. This field is populated by Intel ME. H_GS--Host General Status Register (Intel(R) MEI 1--D22:F0) Address Offset: 4Ch-4Fh Default Value: 00000000h Bit 31:0 23.1.1.17 Attribute: Size: Host General Status(H_GS)--R/W. General Status of Host, this field is not used by Hardware PID--PCI Power Management Capability ID Register (Intel(R) MEI 1--D22:F0) Bit 15:8 7:0 Attribute: Size: RO 16 bits Description Next Capability (NEXT)--RO. Value of 8Ch indicates the location of the next pointer. Capability ID (CID)--RO. Indicates the linked list item is a PCI Power Management Register. PC--PCI Power Management Capabilities Register (Intel(R) MEI 1--D22:F0) Address Offset: 52h-53h Default Value: C803h Attribute: Size: RO 16 bits Bit Description 15:11 PME_Support (PSUP)--RO. This five-bit field indicates the power states in which the function may assert PME#. Intel MEI can assert PME# from any D-state except D1 or D2 which are not supported by Intel MEI. 10:9 8:6 5 Reserved Aux_Current (AC)--RO. Reports the maximum Suspend well current required when in the D3cold state. Value of 00b is reported. Device Specific Initialization (DSI)--RO. Indicates whether device-specific initialization is required. 4 Reserved 3 PME Clock (PMEC)--RO. Indicates that PCI clock is not required to generate PME#. 2:0 770 R/W 32 bits Description Address Offset: 50h-51h Default Value: 8C01h 23.1.1.18 RO 32 bits Version (VS)--RO. Hardwired to 011b to indicate support for Revision 1.2 of the PCI Power Management Specification. Datasheet Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.1.1.19 PMCS--PCI Power Management Control and Status Register (Intel(R) MEI 1--D22:F0) Address Offset: 54h-55h Default Value: 0008h Description 15 PME Status (PMES)--R/WC. Bit is set by Intel ME Firmware. Host software clears bit by writing `1' to bit. This bit is reset when CL_RST# asserted. 8 7:4 3 2 1:0 Reserved PME Enable (PMEE)--R/W. This bit is read/write and is under the control of host SW. It does not directly have an effect on PME events. However, this bit is shadowed so Intel ME FW can monitor it. Intel ME FW will not cause the PMES bit to transition to 1 while the PMEE bit is 0, indicating that host SW had disabled PME. This bit is reset when PLTRST# asserted. Reserved No_Soft_Reset (NSR)--RO. This bit indicates that when the Intel MEI host controller is transitioning from D3hot to D0 due to a power state command, it does not perform an internal reset. Configuration context is preserved. Reserved Power State (PS)--R/W. This field is used both to determine the current power state of the Intel MEI host controller and to set a new power state. The values are: 00 = D0 state (default) 11 = D3hot state The D1 and D2 states are not supported for the Intel MEI host controller. When in the D3hot state, the Intel ME's configuration space is available, but the register memory spaces are not. Additionally, interrupts are blocked. GMES2--General Intel(R) ME Status Register 2 (Intel(R) MEI 1--D22:F0) Address Offset: 60h-63h Default Value: 00000000h Bit 31:0 23.1.1.21 Attribute: Size: RO 32 bits Description General Intel ME Status 2 (ME_GS 2)--RO. This field is populated by Intel ME. GMES3--General Intel(R) ME Status Register 3 (Intel(R) MEI 1--D22:F0) Address Offset: 64h-67h Default Value: 00000000h Bit 31:0 Datasheet R/WC, R/W, RO 16 bits Bit 14:9 23.1.1.20 Attribute: Size: Attribute: Size: RO 32 bits Description General Intel ME Status 3 (ME_GS 3)--RO. This field is populated by Intel ME. 771 Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.1.1.22 GMES4--General Intel(R) ME Status Register 4 (Intel(R) MEI 1--D22:F0) Address Offset: 68h-6Bh Default Value: 00000000h Bit 31:0 23.1.1.23 Attribute: Size: Description General Intel ME Status 4 (ME_GS 4)--RO. This field is populated by Intel ME. GMES5--General Intel(R) ME Status Register 5 (Intel(R) MEI 1--D22:F0) Address Offset: 6Ch-6Fh Default Value: 00000000h Bit 31:0 23.1.1.24 Attribute: Size: General Intel ME Status 5 (ME_GS 5)--RO. This field is populated by Intel ME. H_GS2--Host General Status Register 2 (Intel(R) MEI 1--D22:F0) Attribute: Size: Description 31:0 Host General Status 2 (H_GS 2)--R/W. General Status of Host, this field is not used by Hardware H_GS3--Host General Status Register 3 (Intel(R) MEI 1--D22:F0) Attribute: Size: R/W 32 bits Bit Description 31:0 Host General Status 3( H_GS3)--R/W. General Status of Host, this field is not used by Hardware MID--Message Signaled Interrupt Identifiers Register (Intel(R) MEI 1--D22:F0) Address Offset: 8Ch-8Dh Default Value: 0005h Bit 15:8 7:0 772 R/W 32 bits Bit Address Offset: 74h-77h Default Value: 00000000h 23.1.1.26 RO 32 bits Description Address Offset: 70h-73h Default Value: 00000000h 23.1.1.25 RO 32 bits Attribute: Size: RO 16 bits Description Next Pointer (NEXT)--RO. Value of 00h indicates that this is the last item in the list. Capability ID (CID)--RO. Capabilities ID indicates MSI. Datasheet Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.1.1.27 MC--Message Signaled Interrupt Message Control Register (Intel(R) MEI 1--D22:F0) Address Offset: 8Eh-8Fh Default Value: 0080h Bit 15:8 7 6:1 0 23.1.1.28 Attribute: Size: Description Reserved 64-bit Address Capable (C64)--RO. Specifies that function is capable of generating 64-bit messages. Reserved MSI Enable (MSIE)--R/W. If set, MSI is enabled and traditional interrupt pins are not used to generate interrupts. MA--Message Signaled Interrupt Message Address Register (Intel(R) MEI 1--D22:F0) Address Offset: 90h-93h Default Value: 00000000h Bit 31:2 1:0 23.1.1.29 Attribute: Size: Address (ADDR)--R/W. Lower 32 bits of the system specified message address, always DW aligned. Reserved MUA--Message Signaled Interrupt Upper Address Register (Intel(R) MEI 1--D22:F0) Bit 31:0 Attribute: Size: R/W 32 bits Description Upper Address (UADDR)--R/W. Upper 32 bits of the system specified message address, always DW aligned. MD--Message Signaled Interrupt Message Data Register (Intel(R) MEI 1--D22:F0) Address Offset: 98h-99h Default Value: 0000h Bit 15:0 Datasheet R/W, RO 32 bits Description Address Offset: 94h-97h Default Value: 00000000h 23.1.1.30 R/W, RO 16 bits Attribute: Size: R/W 16 bits Description Data (DATA)--R/W. This 16-bit field is programmed by system software if MSI is enabled. Its content is driven during the data phase of the MSI memory write transaction. 773 Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.1.1.31 HIDM--MEI Interrupt Delivery Mode Register (Intel(R) MEI 1--D22:F0) Address Offset: A0h Default Value: 00h Bit 23.1.1.32 Attribute: Size: Description 7:2 Reserved 1:0 Intel MEI Interrupt Delivery Mode (HIDM)--R/W. These bits control what type of interrupt the Intel MEI will send the host. They are interpreted as follows: 00 = Generate Legacy or MSI interrupt 01 = Generate SCI 10 = Generate SMI HERES--Intel(R) MEI Extend Register Status (Intel(R) MEI 1--D22:F0) Address Offset: BCh-BFh Default Value: 40000000h Attribute: Size: Description 31 Extend Register Valid (ERV)--RO. Set by firmware after all firmware has been loaded. If ERA field is SHA-1, the result of the extend operation is in HER:5-1. If ERA field is SHA-256, the result of the extend operation is in HER:8-1. 30 Extend Feature Present (EFP)--RO. This bit is hardwired to 1 to allow driver software to easily detect the chipset supports the Extend Register FW measurement feature. 3:0 Reserved Extend Register Algorithm (ERA)--RO. This field indicates the hash algorithm used in the FW measurement extend operations. Encodings are: 0h = SHA-1 2h = SHA-256 Other values = Reserved. HERX--Intel(R) MEI Extend Register DWX (Intel(R) MEI 1--D22:F0) Address Offset: HER1: C0h-C3h HER2: C4h-C7h HER3: C8h-CBh HER4: CCh-CFh HER5: D0h-D3h HER6: D4h-D7h HER7: D8h-dBh HER8: DCh-DFh Default Value: 00000000h Bit 31:0 Attribute: RO Size: 32 bits Description Extend Register DWX (ERDWX)--RO. Xth DWord result of the extend operation. Note: 774 RO 32 bits Bit 29:4 23.1.1.33 R/W 8 bits Extend Operation is HER[5:1] if using SHA-1. If using SHA-256 then Extend Operation is HER[8:1] Datasheet Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.1.2 MEI0_MBAR--Intel(R) MEI 1 MMIO Registers These MMIO registers are accessible starting at the Intel MEI 1 MMIO Base Address (MEI0_MBAR) which gets programmed into D22:F0:Offset 10-17h. These registers are reset by PLTRST# unless otherwise noted. Table 23-1. Intel(R) MEI 1 MMIO Register Address Map 23.1.2.1 MEI0_MBAR+Of fset Mnemonic 00-03h H_CB_WW 04h-07h H_CSR Register Name 00000000h W Host Control Status 02000000h RO, R/W, R/WC 08h-0Bh ME_CB_RW Intel ME Circular Buffer Read Window FFFFFFFFh RO 0Ch-0Fh ME_CSR_HA Intel ME Control Status Host Access 02000000h RO H_CB_WW--Host Circular Buffer Write Window Register (Intel(R) MEI 1 MMIO Register) Attribute: Size: WO 32 bits Bit Description 31:0 Host Circular Buffer Write Window Field (H_CB_WWF). This bit field is for host to write into its circular buffer. The host's circular buffer is located at the Intel ME subsystem address specified in the Host CB Base Address register. This field is write only, reads will return arbitrary data. Writes to this register will increment the H_CBWP as long as ME_RDY is 1. When ME_RDY is 0, writes to this register have no effect and are not delivered to the H_CB, nor is H_CBWP incriminated. H_CSR--Host Control Status Register (Intel(R) MEI 1 MMIO Register) Address Offset: MEI0_MBAR + 04h Default Value: 02000000h Attribute: Size: RO, R/W, R/WC 32 bits Bit Description 31:24 Host Circular Buffer Depth (H_CBD)--RO. This field indicates the maximum number of 32-bit entries available in the host circular buffer (H_CB). Host software uses this field along with the H_CBRP and H_CBWP fields to calculate the number of valid entries in the H_CB to read or # of entries available for write. This field is implemented with a "1-hot" scheme. Only one bit will be set to a "1" at a time. Each bit position represents the value n of a buffer depth of (2^n). For example, when bit# 1 is 1, the buffer depth is 2; when bit#2 is 1, the buffer depth is 4, and so on. The allowed buffer depth values are 2, 4, 8, 16, 32, 64 and 128. 23:16 Host CB Write Pointer (H_CBWP)--RO. Points to next location in the H_CB for host to write the data. Software uses this field along with H_CBRP and H_CBD fields to calculate the number of valid entries in the H_CB to read or number of entries available for write. 15:8 Host CB Read Pointer (H_CBRP)--RO. Points to next location in the H_CB where a valid data is available for embedded controller to read. Software uses this field along with H_CBWR and H_CBD fields to calculate the number of valid entries in the host CB to read or number of entries available for write. 7:5 Datasheet Attribute Host Circular Buffer Write Window Address Offset: MEI0_MBAR + 00h Default Value: 00000000h 23.1.2.2 Default Reserved Note: For writes to this register, these bits shall be written as 000b. 4 Host Reset (H_RST)--R/W. Setting this bit to 1 will initiate a Intel MEI reset sequence to get the circular buffers into a known good state for host and Intel ME communication. When this bit transitions from 0 to 1, hardware will clear the H_RDY and ME_RDY bits. 3 Host Ready (H_RDY)--R/W. This bit indicates that the host is ready to process messages. 775 Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.1.2.3 Bit Description 2 Host Interrupt Generate (H_IG)--R/W. Once message(s) are written into its CB, the host sets this bit to one for the HW to set the ME_IS bit in the ME_CSR and to generate an interrupt message to Intel ME. HW will send the interrupt message to Intel ME only if the ME_IE is enabled. HW then clears this bit to 0. 1 Host Interrupt Status (H_IS)--R/WC. Hardware sets this bit to 1 when ME_IG bit is set to 1. Host clears this bit to 0 by writing a 1 to this bit position. H_IE has no effect on this bit. 0 Host Interrupt Enable (H_IE)--R/W. Host sets this bit to 1 to enable the host interrupt (INTR# or MSI) to be asserted when H_IS is set to 1. ME_CB_RW--Intel(R) ME Circular Buffer Read Window Register (Intel(R) MEI 1 MMIO Register) Address Offset: MEI0_MBAR + 08h Default Value: FFFFFFFFh 23.1.2.4 Attribute: Size: Bit Description 31:0 Intel ME Circular Buffer Read Window Field (ME_CB_RWF). This bit field is for host to read from the Intel ME Circular Buffer. The Intel ME circular buffer is located at the Intel ME subsystem address specified in the Intel ME CB Base Address register. This field is read only, writes have no effect. Reads to this register will increment the ME_CBRP as long as ME_RDY is 1. When ME_RDY is 0, reads to this register have no effect, all 1s are returned, and ME_CBRP is not incremented. ME_CSR_HA--Intel(R) ME Control Status Host Access Register (Intel(R) MEI 1 MMIO Register) Address Offset: MEI0_MBAR + 0Ch Default Value: 02000000h Bit Attribute: Size: Intel ME Circular Buffer Depth Host Read Access (ME_CBD_HRA). Host read only access to ME_CBD. 23:16 Intel ME CB Write Pointer Host Read Access (ME_CBWP_HRA). Host read only access to ME_CBWP. 7:5 RO 32 bits Description 31:24 15:8 776 RO 32 bits Intel ME CB Read Pointer Host Read Access (ME_CBRP_HRA). Host read only access to ME_CBRP. Reserved 4 Intel ME Reset Host Read Access (ME_RST_HRA). Host read access to ME_RST. 3 Intel ME Ready Host Read Access (ME_RDY_HRA): Host read access to ME_RDY. 2 Intel ME Interrupt Generate Host Read Access (ME_IG_HRA). Host read only access to ME_IG. 1 Intel ME Interrupt Status Host Read Access (ME_IS_HRA). Host read only access to ME_IS. 0 Intel ME Interrupt Enable Host Read Access (ME_IE_HRA). Host read only access to ME_IE. Datasheet Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.2 Second Intel(R) Management Engine Interface (Intel(R) MEI 2) Configuration Registers (Intel(R) MEI 2--D22:F1) 23.2.1 PCI Configuration Registers (Intel(R) MEI 2--D22:F2) Table 23-2. Intel(R) MEI 2 Configuration Registers Address Map (Intel(R) MEI 2--D22:F1) (Sheet 1 of 2) Datasheet Offset Mnemonic 00h-01h VID 02h-03h DID 04h-05h PCICMD 06h-07h PCISTS 08h RID 09h-0Bh CC 0Eh HTYPE 10h-17h MEI1_MBAR 2Ch-2Dh SVID Register Name Default Attribute Vendor Identification 8086h RO Device Identification See register description RO 0000h R/W, RO PCI Command PCI Status Revision Identification Class Code 0010h RO See register description RO 078000h RO 80h RO 0000000000000 004h R/W, RO Subsystem Vendor ID 0000h R/WO Subsystem ID 0000h R/WO 50h RO Header Type Intel MEI 2 MMIO Base Address 2Eh-2Fh SID 34h CAPP 3Ch-3Dh INTR Interrupt Information 0200h R/W, RO 40h-43h HFS Host Firmware Status 00000000h RO 48h-4Bh GMES General Intel ME Status 00000000h RO 4Ch-4Fh H_GS Host General Status 00000000h R/W 50h-51h PID PCI Power Management Capability ID 8C01h RO 52h-53h PC PCI Power Management Capabilities C803h RO 54h-55h PMCS PCI Power Management Control and Status 0008h R/WC, R/W, RO 60h-63h GMES2 General Intel ME Status 2 00000000h RO Capabilities List Pointer 64h-67h GMES3 General Intel ME Status 3 00000000h RO 68h-6Bh GMES4 General Intel ME Status 4 00000000h RO 6Ch-6Fh GMES5 General Intel ME Status 5 00000000h RO 70h-73h H_GS2 Host General Status 2 00000000h RW Host General Status 3 74h-77h H_GS3 00000000h RW 8Ch-8Dh MID Message Signaled Interrupt Identifiers 0005h RO 8Eh-8Fh MC Message Signaled Interrupt Message Control 0080h R/W, RO 90h-93h MA Message Signaled Interrupt Message Address 00000000h R/W, RO 94h-97h MUA Message Signaled Interrupt Upper Address 00000000h R/W 98h-99h MD 0000h R/W Message Signaled Interrupt Message Data 777 Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) Table 23-2. Intel(R) MEI 2 Configuration Registers Address Map (Intel(R) MEI 2--D22:F1) (Sheet 2 of 2) 23.2.1.1 Offset Mnemonic A0h HIDM BC-BFh HERES C0-DFh HER[1:8] Register Name Intel MEI Interrupt Delivery Mode R/W 40000000h RO 00000000h RO VID--Vendor Identification Register (Intel(R) MEI 2--D22:F1) 15:0 Attribute: Size: RO 16 bits Description Vendor ID (VID)--RO. This is a 16-bit value assigned to Intel. DID--Device Identification Register (Intel(R) MEI 2--D22:F1) Address Offset: 02h-03h Default Value: See bit description Bit 15:0 Attribute: Size: RO 16 bits Description Device ID (DID)--RO. This is a 16-bit value assigned to the Intel Management Engine Interface controller. See Section 1.3 for the value of the DID Register. PCICMD--PCI Command Register (Intel(R) MEI 2--D22:F1) Address Offset: 04h-05h Default Value: 0000h Bit 15:11 Attribute: Size: R/W, RO 16 bits Description Reserved 10 Interrupt Disable (ID)--R/W. Disables this device from generating PCI line based interrupts. This bit does not have any effect on MSI operation. 9:3 Reserved 2 Bus Master Enable (BME)--R/W. Controls the Intel MEI host controller's ability to act as a system memory master for data transfers. When this bit is cleared, Intel MEI bus master activity stops and any active DMA engines return to an idle condition. This bit is made visible to firmware through the H_PCI_CSR register, and changes to this bit may be configured by the H_PCI_CSR register to generate an Intel ME MSI. When this bit is 0, Intel MEI is blocked from generating MSI to the host processor. Note: 778 00h Intel MEI Extended Register DW[1:8] Bit 23.2.1.3 Attribute Intel MEI Extended Register Status Address Offset: 00h-01h Default Value: 8086h 23.2.1.2 Default This bit does not block Intel MEI accesses to Intel ME UMA; that is, writes or reads to the host and Intel ME circular buffers through the read window and write window registers still cause Intel ME backbone transactions to Intel ME UMA. 1 Memory Space Enable (MSE)--R/W. Controls access to the Intel ME memory mapped register space. 0 = Disable. Memory cycles within the range specified by the memory base and limit registers are master aborted. 1 = Enable. Allows memory cycles within the range specified by the memory base and limit registers accepted. 0 Reserved Datasheet Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.2.1.4 PCISTS--PCI Status Register (Intel(R) MEI 2--D22:F1) Address Offset: 06h-07h Default Value: 0010h Bit 15:5 Attribute: Size: RO 16 bits Description Reserved 4 Capabilities List (CL)--RO. Indicates the presence of a capabilities list, hardwired to 1. 3 Interrupt Status--RO. Indicates the interrupt status of the device. 0 = Interrupt is de-asserted. 1 = Interrupt is asserted. 2:0 23.2.1.5 Reserved RID--Revision Identification Register (Intel(R) MEI 2--D22:F1) Offset Address: 08h Default Value: See bit description 23.2.1.6 Attribute: Size: Bit Description 7:0 Revision ID--RO. This field indicates the device specific revision identifier. See Section 1.3 for the value of the RID Register. CC--Class Code Register (Intel(R) MEI 2--D22:F1) Address Offset: 09h-0Bh Default Value: 078000h Bit 23:16 15:8 7:0 23.2.1.7 Attribute: Size: RO 24 bits Description Base Class Code (BCC)--RO. Indicates the base class code of the Intel MEI device. Sub Class Code (SCC)--RO. Indicates the sub class code of the Intel MEI device. Programming Interface (PI)--RO. Indicates the programming interface of the Intel MEI device. HTYPE--Header Type Register (Intel(R) MEI 2--D22:F1) Address Offset: 0Eh Default Value: 80h Bit 7 6:0 Datasheet RO 8 bits Attribute: Size: RO 8 bits Description Multi-Function Device (MFD)--RO. Indicates the Intel MEI host controller is part of a multifunction device. Header Layout (HL)--RO. Indicates that the Intel MEI uses a target device layout. 779 Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.2.1.8 MEI1_MBAR--Intel MEI 2 MMIO Base Address (Intel(R) MEI 2--D22:F1) Address Offset: 10h-17h Default Value: 0000000000000004h Attribute: Size: R/W, RO 64 bits This register allocates space for the Intel MEI memory mapped registers. Bit 63:4 3 2:1 0 23.2.1.9 Description Base Address (BA)--R/W. Software programs this field with the base address of this region. Prefetchable Memory (PM)--RO. Indicates that this range is not prefetchable. Type (TP)--RO. Set to 10b to indicate that this range can be mapped anywhere in 64-bit address space. Resource Type Indicator (RTE)--RO. Indicates a request for register memory space. SVID--Subsystem Vendor ID Register (Intel(R) MEI 2--D22:F1) Address Offset: 2Ch-2Dh Default Value: 0000h Bit 15:0 23.2.1.10 Attribute: Size: Description Subsystem Vendor ID (SSVID)--R/WO. Indicates the sub-system vendor identifier. This field should be programmed by BIOS during boot-up. Once written, this register becomes Read Only. This field can only be cleared by PLTRST#. Note: Register must be written as a Word write or as a DWord write with SID register. SID--Subsystem ID Register (Intel(R) MEI 2--D22:F1) Address Offset: 2Eh-2Fh Default Value: 0000h Attribute: Size: Description 15:0 Subsystem ID (SSID)--R/WO. Indicates the sub-system identifier. This field should be programmed by BIOS during boot-up. Once written, this register becomes Read Only. This field can only be cleared by PLTRST#. Register must be written as a Word write or as a DWord write with SVID register. CAPP--Capabilities List Pointer Register (Intel(R) MEI 2--D22:F1) Address Offset: 34h Default Value: 50h 780 R/WO 16 bits Bit Note: 23.2.1.11 R/WO 16 bits Attribute: Size: RO 8 bits Bit Description 7:0 Capabilities Pointer (PTR)--RO. Indicates that the pointer for the first entry in the capabilities list is at 50h in configuration space. Datasheet Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.2.1.12 INTR--Interrupt Information Register (Intel(R) MEI 2--D22:F1) Address Offset: 3Ch-3Dh Default Value: 0200h 23.2.1.13 Attribute: Size: Bit Description 15:8 Interrupt Pin (IPIN)--RO. This field indicates the interrupt pin the Intel MEI host controller uses. A value of 1h/2h/3h/4h indicates that this function implements legacy interrupt on INTA/INTB/INTC/ INTD, respectively. 7:0 Interrupt Line (ILINE)--R/W. Software written value to indicate which interrupt line (vector) the interrupt is connected to. No hardware action is taken on this register. HFS--Host Firmware Status Register (Intel(R) MEI 2--D22:F1) Address Offset: 40h-43h Default Value: 00000000h 23.2.1.14 Attribute: Size: Description 31:0 Host Firmware Status (HFS)--RO. This register field is used by Firmware to reflect the operating environment to the host. GMES--General Intel(R) ME Status Register (Intel(R) MEI 2--D22:F1) Bit 31:0 Attribute: Size: General Intel ME Status (ME_GS)--RO. This field is populated by Intel ME. H_GS--Host General Status Register (Intel(R) MEI 2--D22:F1) Bit 31:0 Attribute: Size: R/W 32 bits Description Host General Status (H_GS)--R/W. General Status of Host, this field is not used by Hardware PID--PCI Power Management Capability ID Register (Intel(R) MEI 2--D22:F1) Address Offset: 50h-51h Default Value: 8C01h Bit 15:8 7:0 Datasheet RO 32 bits Description Address Offset: 4Ch-4Fh Default Value: 00000000h 23.2.1.16 RO 32 bits Bit Address Offset: 48h-4Bh Default Value: 00000000h 23.2.1.15 R/W, RO 16 bits Attribute: Size: RO 16 bits Description Next Capability (NEXT)--RO. Value of 8Ch indicates the location of the next pointer. Capability ID (CID)--RO. Indicates the linked list item is a PCI Power Management Register. 781 Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.2.1.17 PC--PCI Power Management Capabilities Register (Intel(R) MEI 2--D22:F1) Address Offset: 52h-53h Default Value: C803h Description 15:11 PME_Support (PSUP)--RO. This five-bit field indicates the power states in which the function may assert PME#. Intel MEI can assert PME# from any D-state except D1 or D2 which are not supported by Intel MEI. 8:6 Reserved Aux_Current (AC)--RO. Reports the maximum Suspend well current required when in the D3cold state. Value of 00b is reported. 5 Device Specific Initialization (DSI)--RO. Indicates whether device-specific initialization is required. 4 Reserved 3 PME Clock (PMEC)--RO. Indicates that PCI clock is not required to generate PME#. 2:0 Version (VS)--RO. Hardwired to 011b to indicate support for Revision 1.2 of the PCI Power Management Specification. PMCS--PCI Power Management Control and Status Register (Intel(R) MEI 2--D22:F1) Address Offset: 54h-55h Default Value: 0008h Bit 15 14:9 8 7:4 3 2 1:0 782 RO 16 bits Bit 10:9 23.2.1.18 Attribute: Size: Attribute: Size: R/WC, R/W, RO 16 bits Description PME Status (PMES)--R/WC. Bit is set by Intel ME Firmware. Host software clears bit by writing 1 to bit. This bit is reset when CL_RST# is asserted. Reserved PME Enable (PMEE)--R/W. This bit is read/write and is under the control of host SW. It does not directly have an effect on PME events. However, this bit is shadowed so Intel ME FW can monitor it. Intel ME FW will not cause the PMES bit to transition to 1 while the PMEE bit is 0, indicating that host SW had disabled PME. This bit is reset when PLTRST# asserted. Reserved No_Soft_Reset (NSR)--RO. This bit indicates that when the Intel MEI host controller is transitioning from D3hot to D0 due to a power state command, it does not perform an internal reset. Configuration context is preserved. Reserved Power State (PS)--R/W. This field is used both to determine the current power state of the Intel MEI host controller and to set a new power state. The values are: 00 = D0 state (default) 11 = D3hot state The D1 and D2 states are not supported for the Intel MEI host controller. When in the D3hot state, the Intel ME's configuration space is available, but the register memory spaces are not. Additionally, interrupts are blocked. Datasheet Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.2.1.19 GMES2--General Intel(R) ME Status Register 2 (Intel(R) MEI 2--D22:F1) Address Offset: 60h-63h Default Value: 00000000h Bit 31:0 23.2.1.20 Attribute: Size: Description General Intel ME Status 2 (ME_GS 2)--RO. This field is populated by Intel ME. GMES3--General Intel(R) ME Status Register 3 (Intel(R) MEI 2--D22:F1) Address Offset: 64h-67h Default Value: 00000000h Bit 31:0 23.2.1.21 Attribute: Size: General Intel ME Status 3 (ME_GS 3)--RO. This field is populated by Intel ME. GMES4--General Intel(R) ME Status Register 4 (Intel(R) MEI 2--D22:F1) Bit 31:0 Attribute: Size: General Intel ME Status 4 (ME_GS 4)--RO. This field is populated by Intel ME. GMES5--General Intel(R) ME Status Register 5 (Intel(R) MEI 2--D22:F1) Bit 31:0 Attribute: Size: RO 32 bits Description General Intel ME Status 5 (ME_GS 5)--RO. This field is populated by Intel ME. H_GS2--Host General Status Register 2 (Intel(R) MEI 2--D22:F1) Address Offset: 70h-73h Default Value: 00000000h Datasheet RO 32 bits Description Address Offset: 6Ch-6Fh Default Value: 00000000h 23.2.1.23 RO 32 bits Description Address Offset: 68h-6Bh Default Value: 00000000h 23.2.1.22 RO 32 bits Attribute: Size: R/W 32 bits Bit Description 31:0 Host General Status 2 (H_GS 2)--R/W. General Status of Host, this field is not used by Hardware 783 Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.2.1.24 H_GS3--Host General Status Register 3 (Intel(R) MEI 2--D22:F1) Address Offset: 74h-77h Default Value: 00000000h 23.2.1.25 Attribute: Size: Bit Description 31:0 Host General Status 3 (H_GS3)--R/W. General Status of Host, this field is not used by Hardware MID--Message Signaled Interrupt Identifiers Register (Intel(R) MEI 2--D22:F1) Address Offset: 8Ch-8Dh Default Value: 0005h Bit 15:8 7:0 23.2.1.26 Attribute: Size: Next Pointer (NEXT)--RO. Value of 00h indicates that this is the last item in the list. Capability ID (CID)--RO. Capabilities ID indicates MSI. MC--Message Signaled Interrupt Message Control Register (Intel(R) MEI 2--D22:F1) Bit 15:8 7 6:1 0 Attribute: Size: R/W, RO 16 bits Description Reserved 64-bit Address Capable (C64)--RO. Specifies that function is capable of generating 64-bit messages. Reserved MSI Enable (MSIE)--R/W. If set, MSI is enabled and traditional interrupt pins are not used to generate interrupts. MA--Message Signaled Interrupt Message Address Register (Intel(R) MEI 2--D22:F1) Address Offset: 90h-93h Default Value: 00000000h Bit 31:2 1:0 784 RO 16 bits Description Address Offset: 8Eh-8Fh Default Value: 0080h 23.2.1.27 R/W 32 bits Attribute: Size: R/W, RO 32 bits Description Address (ADDR)--R/W. Lower 32 bits of the system specified message address, always DW aligned. Reserved Datasheet Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.2.1.28 MUA--Message Signaled Interrupt Upper Address Register (Intel(R) MEI 2--D22:F1) Address Offset: 94h-97h Default Value: 00000000h Bit 31:0 23.2.1.29 Attribute: Size: Description Upper Address (UADDR)--R/W. Upper 32 bits of the system specified message address, always DW aligned. MD--Message Signaled Interrupt Message Data Register (Intel(R) MEI 2--D22:F1) Address Offset: 98h-99h Default Value: 0000h Bit 15:0 23.2.1.30 Attribute: Size: Data (DATA)--R/W. This 16-bit field is programmed by system software if MSI is enabled. Its content is driven during the data phase of the MSI memory write transaction. HIDM--Intel(R) MEI Interrupt Delivery Mode Register (Intel(R) MEI 2--D22:F1) Bit Attribute: Size: R/W 8 bits Description 7:2 Reserved 1:0 Intel MEI Interrupt Delivery Mode (HIDM)--R/W. These bits control what type of interrupt the Intel MEI will send the host. They are interpreted as follows: 00 = Generate Legacy or MSI interrupt 01 = Generate SCI 10 = Generate SMI HERES--Intel(R) MEI Extend Register Status (Intel(R) MEI 2--D22:F1) Address Offset: BCh-BFh Default Value: 40000000h Attribute: Size: RO 32 bits Bit Description 31 Extend Register Valid (ERV)--RO. Set by firmware after all firmware has been loaded. If ERA field is SHA-1, the result of the extend operation is in HER:5-1. If ERA field is SHA-256, the result of the extend operation is in HER:8-1. 30 Extend Feature Present (EFP)--RO. This bit is hardwired to 1 to allow driver software to easily detect the chipset supports the Extend Register FW measurement feature. 29:4 3:0 Datasheet R/W 16 bits Description Address Offset: A0h Default Value: 00h 23.2.1.31 R/W 32 bits Reserved Extend Register Algorithm (ERA)--RO. This field indicates the hash algorithm used in the FW measurement extend operations. Encodings are: 0h = SHA-1 2h = SHA-256 Other values = Reserved 785 Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.2.1.32 HERX--Intel(R) MEI Extend Register DWX (Intel(R) MEI 2--D22:F1) Address Offset: HER1: C0h-C3h HER2: C4h-C7h HER3: C8h-CBh HER4: CCh-CFh HER5: D0h-D3h HER6: D4h-D7h HER7: D8h-dBh HER8: DCh-DFh Default Value: 00000000h Bit 31:0 RO Size: 32 bits Description Extend Register DWX (ERDWX)--RO. Xth DWord result of the extend operation. Note: 23.2.2 Attribute: Extend Operation is HER[5:1] if using SHA-1. If using SHA-256, then Extend Operation is HER[8:1]. MEI1_MBAR--Intel(R) MEI 2 MMIO Registers These MMIO registers are accessible starting at the Intel MEI 2 MMIO Base Address (MEI1_MBAR) which gets programmed into D22:F1:Offset 10-17h. These registers are reset by PLTRST# unless otherwise noted. Table 23-3. Intel(R) MEI 2 MMIO Register Address Map 23.2.2.1 MEI1_MBAR+ Offset Mnemonic 00-03h H_CB_WW 04h-07h H_CSR 08h-0Bh 0Ch-0Fh Register Name Default Attribute Host Circular Buffer Write Window 00000000h W Host Control Status 02000000h R/W, R/WC, RO ME_CB_RW Intel ME Circular Buffer Read Window FFFFFFFFh RO ME_CSR_HA Intel ME Control Status Host Access 02000000h RO H_CB_WW--Host Circular Buffer Write Window (Intel(R) MEI 2 MMIO Register) Address Offset: MEI1_MBAR + 00h Default Value: 00000000h 786 Attribute: Size: W 32 bits Bit Description 31:0 Host Circular Buffer Write Window Field (H_CB_WWF)--W. This bit field is for host to write into its circular buffer. The host's circular buffer is located at the Intel ME subsystem address specified in the Host CB Base Address register. This field is write only; reads will return arbitrary data. Writes to this register will increment the H_CBWP as long as ME_RDY is 1. When ME_RDY is 0, writes to this register have no effect and are not delivered to the H_CB, nor is H_CBWP incremented. Datasheet Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.2.2.2 H_CSR--Host Control Status Register (Intel(R) MEI 2 MMIO Register) Address Offset: MEI1_MBAR + 04h Default Value: 02000000h Description 31:24 Host Circular Buffer Depth (H_CBD)--RO. This field indicates the maximum number of 32-bit entries available in the host circular buffer (H_CB). Host software uses this field along with the H_CBRP and H_CBWP fields to calculate the number of valid entries in the H_CB to read or # of entries available for write. This field is implemented with a "1-hot" scheme. Only one bit will be set to a "1" at a time. Each bit position represents the value n of a buffer depth of (2^n). For example, when bit# 1 is 1, the buffer depth is 2; when bit#2 is 1, the buffer depth is 4, and so on. The allowed buffer depth values are 2, 4, 8, 16, 32, 64 and 128. 23:16 Host CB Write Pointer (H_CBWP)--RO. Points to next location in the H_CB for host to write the data. Software uses this field along with H_CBRP and H_CBD fields to calculate the number of valid entries in the H_CB to read or number of entries available for write. 15:8 Host CB Read Pointer (H_CBRP)--RO. Points to next location in the H_CB where a valid data is available for embedded controller to read. Software uses this field along with H_CBWR and H_CBD fields to calculate the number of valid entries in the host CB to read or number of entries available for write. Reserved Note: For writes to this register, these bits shall be written as 000b. 4 Host Reset (H_RST)--R/W. Setting this bit to 1 will initiate a Intel MEI reset sequence to get the circular buffers into a known good state for host and Intel ME communication. When this bit transitions from 0 to 1, hardware will clear the H_RDY and ME_RDY bits. 3 Host Ready (H_RDY)--R/W. This bit indicates that the host is ready to process messages. 2 Host Interrupt Generate (H_IG)--R/W. Once message(s) are written into its CB, the host sets this bit to one for the HW to set the ME_IS bit in the ME_CSR and to generate an interrupt message to Intel ME. HW will send the interrupt message to Intel ME only if the ME_IE is enabled. HW then clears this bit to 0. 1 Host Interrupt Status (H_IS)--R/WC. Hardware sets this bit to 1 when ME_IG bit is set to 1. Host clears this bit to 0 by writing a 1 to this bit position. H_IE has no effect on this bit. 0 Host Interrupt Enable (H_IE)--R/W. Host sets this bit to 1 to enable the host interrupt (INTR# or MSI) to be asserted when H_IS is set to 1. ME_CB_RW--Intel(R) ME Circular Buffer Read Window Register (Intel(R) MEI 2 MMIO Register) Address Offset: MEI1_MBAR + 08h Default Value: FFFFFFFFh Datasheet RO, R/W, R/WC 32 bits Bit 7:5 23.2.2.3 Attribute: Size: Attribute: Size: RO 32 bits Bit Description 31:0 Intel ME Circular Buffer Read Window Field (ME_CB_RWF). This bit field is for host to read from the Intel ME Circular Buffer. The Intel ME's circular buffer is located at the Intel ME subsystem address specified in the Intel ME CB Base Address register. This field is read only, writes have no effect. Reads to this register will increment the ME_CBRP as long as ME_RDY is 1. When ME_RDY is 0, reads to this register have no effect, all 1s are returned, and ME_CBRP is not incremented. 787 Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.2.2.4 ME_CSR_HA--Intel(R) ME Control Status Host Access Register (Intel(R) MEI 2 MMIO Register) Address Offset: MEI1_MBAR + 0Ch Default Value: 02000000h Bit Intel ME Circular Buffer Depth Host Read Access (ME_CBD_HRA). Host read only access to ME_CBD. 23:16 Intel ME CB Write Pointer Host Read Access (ME_CBWP_HRA). Host read only access to ME_CBWP. 7:5 RO 32 bits Description 31:24 15:8 788 Attribute: Size: Intel ME CB Read Pointer Host Read Access (ME_CBRP_HRA). Host read only access to ME_CBRP. Reserved 4 Intel ME Reset Host Read Access (ME_RST_HRA). Host read access to ME_RST. 3 Intel ME Ready Host Read Access (ME_RDY_HRA). Host read access to ME_RDY. 2 Intel ME Interrupt Generate Host Read Access (ME_IG_HRA). Host read only access to ME_IG. 1 Intel ME Interrupt Status Host Read Access (ME_IS_HRA). Host read only access to ME_IS. 0 Intel ME Interrupt Enable Host Read Access (ME_IE_HRA). Host read only access to ME_IE. Datasheet Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.3 IDE Redirect IDER Registers (IDER--D22:F2) 23.3.1 PCI Configuration Registers (IDER--D22:F2) Table 23-4. IDE Redirect Function IDER Register Address Map Address Offset 23.3.1.1 Register Symbol Register Name Attribute 00h-01h VID Vendor Identification 8086h RO 02h-03h DID Device Identification See register description RO 04h-05h PCICMD PCI Command 0000h RO, R/W 06h-07h PCISTS PCI Status 00B0h RO 08h RID Revision ID See register description RO 09h-0Bh CC Class Codes 010185h RO 0Ch CLS Cache Line Size 10h-13h PCMdBA 00h RO Primary Command Block IO Bar 00000001h RO, R/W 14h-17h PCTLBA Primary Control Block Base Address 00000001h RO, R/W 18h-1Bh SCMdBA Secondary Command Block Base Address 00000001h RO, R/W 1Ch-1Fh SCTLBA Secondary Control Block base Address 00000001h RO, R/W 20h-23h LBAR Legacy Bus Master Base Address 00000001h RO, R/W 2Ch-2Dh SVID Subsystem Vendor ID 0000h R/WO 2Eh-2Fh SID Subsystem ID 8086h R/WO 34h CAPP Capabilities Pointer C8h RO 3Ch-3Dh INTR Interrupt Information 0300h R/W, RO C8h-C9h PID PCI Power Management Capability ID D001h RO CAh-CBh PC PCI Power Management Capabilities 0023h RO CCh-CFh PMCS 00000000h RO, R/W, RO/V D0h-D1h MID 0005h RO D2h-D3h MC Message Signaled Interrupt Message Control 0080h RO, R/W D4h-D7h MA Message Signaled Interrupt Message Address 00000000h R/W, RO D8h-dBh MAU Message Signaled Interrupt Message Upper Address 00000000h RO, R/W DC-DDh MD 0000h R/W PCI Power Management Control and Status Message Signaled Interrupt Capability ID Message Signaled Interrupt Message Data VID--Vendor Identification Register (IDER--D22:F2) Address Offset: 00-01h Default Value: 8086h Bit 15:0 Datasheet Default Value Attribute: Size: RO 16 bits Description Vendor ID (VID)--RO. This is a 16-bit value assigned by Intel. 789 Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.3.1.2 DID--Device Identification Register (IDER--D22:F2) Address Offset: 02-03h Default Value: See bit description Bit 15:0 23.3.1.3 Attribute: Size: Description Device ID (DID)--RO. This is a 16-bit value assigned to the PCH IDER controller. See Section 1.3 for the value of the DID Register. PCICMD--PCI Command Register (IDER--D22:F2) Address Offset: 04-05h Default Value: 0000h Bit 15:11 23.3.1.4 Attribute: Size: Reserved 10 Interrupt Disable (ID)--R/W. This disables pin-based INTx# interrupts. This bit has no effect on MSI operation. When set, internal INTx# messages will not be generated. When cleared, internal INTx# messages are generated if there is an interrupt and MSI is not enabled. 9:3 Reserved 2 Bus Master Enable (BME)--RO. This bit controls the PT function's ability to act as a master for data transfers. This bit does not impact the generation of completions for split transaction commands. 1 Memory Space Enable (MSE)--RO. PT function does not contain target memory space. 0 I/O Space enable (IOSE)--RO. This bit controls access to the PT function's target I/O space. PCISTS--PCI Device Status Register (IDER--D22:F2) Bit 15:11 10:9 8:5 Attribute: Size: RO 16 bits Description Reserved DEVSEL# Timing Status (DEVT)--RO. This bit controls the device select time for the PT function's PCI interface. Reserved 4 Capabilities List (CL)--RO. This bit indicates that there is a capabilities pointer implemented in the device. 3 Interrupt Status (IS)--RO. This bit reflects the state of the interrupt in the function. Setting of the Interrupt Disable bit to 1 has no affect on this bit. Only when this bit is a 1 and ID bit is 0 is the INTc interrupt asserted to the Host. 2:0 Reserved RID--Revision Identification Register (IDER--D22:F2) Address Offset: 08h Default Value: See bit description Bit 7:0 790 RO, R/W 16 bits Description Address Offset: 06-07h Default Value: 00B0h 23.3.1.5 RO 16 bits Attribute: Size: RO 8 bits Description Revision ID--RO. This field indicates the device specific revision identifier. See Section 1.3 for the value of the RID Register. Datasheet Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.3.1.6 CC--Class Codes Register (IDER--D22:F2) Address Offset: 09-0Bh Default Value: 010185h 23.3.1.7 Attribute: Size: Bit Description 23:16 Base Class Code (BCC)--RO This field indicates the base class code of the IDER host controller device. 15:8 Sub Class Code (SCC)--RO This field indicates the sub class code of the IDER host controller device. 7:0 Programming Interface (PI)--RO This field indicates the programming interface of the IDER host controller device. CLS--Cache Line Size Register (IDER--D22:F2) Address Offset: 0Ch Default Value: 00h Bit 7:0 23.3.1.8 Attribute: Size: Cache Line Size (CLS)--RO. All writes to system memory are Memory Writes. PCMdBA--Primary Command Block IO Bar Register (IDER--D22:F2) Bit 31:16 15:3 2:1 0 Attribute: Size: RO, R/W 32 bits Description Reserved Base Address (BAR)--R/W Base Address of the BAR0 I/O space (8 consecutive I/O locations). Reserved Resource Type Indicator (RTE)--RO. This bit indicates a request for I/O space. PCTLBA--Primary Control Block Base Address Register (IDER--D22:F2) Address Offset: 14-17h Default Value: 00000001h Bit 31:16 15:2 Datasheet RO 8 bits Description Address Offset: 10-13h Default Value: 00000001h 23.3.1.9 RO 24 bits Attribute: Size: RO, R/W 32 bits Description Reserved Base Address (BAR)--R/W. Base Address of the BAR1 I/O space (4 consecutive I/O locations) 1 Reserved 0 Resource Type Indicator (RTE)--RO. This bit indicates a request for I/O space 791 Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.3.1.10 SCMdBA--Secondary Command Block Base Address Register (IDER--D22:F2) Address Offset: 18-1Bh Default Value: 00000001h Bit 31:16 15:3 2:1 0 23.3.1.11 Attribute: Size: Description Reserved Base Address (BAR)--R/W. Base Address of the I/O space (8 consecutive I/O locations). Reserved Resource Type Indicator (RTE)--RO. This bit indicates a request for I/O space. SCTLBA--Secondary Control Block base Address Register (IDER--D22:F2) Address Offset: 1C-1Fh Default Value: 00000001h1 Bit 31:16 15:2 23.3.1.12 Attribute: Size: Reserved Base Address (BAR)--R/W. Base Address of the I/O space (4 consecutive I/O locations). 1 Reserved 0 Resource Type Indicator (RTE)--RO. This bit indicates a request for I/O space. LBAR--Legacy Bus Master Base Address Register (IDER--D22:F2) Bit 31:16 15:4 3:1 0 Attribute: Size: RO, R/W 32 bits Description Reserved Base Address (BA)--R/W. Base Address of the I/O space (16 consecutive I/O locations). Reserved Resource Type Indicator (RTE)--RO. This bit indicates a request for I/O space. SVID--Subsystem Vendor ID Register (IDER--D22:F2) Address Offset: 2Ch-2Dh Default Value: 0000h Bit 15:0 792 RO, R/W 32 bits Description Address Offset: 20-23h Default Value: 00000001h 23.3.1.13 RO, R/W 32 bits Attribute: Size: R/WO 16 bits Description Subsystem Vendor ID (SSVID)--R/WO. Indicates the sub-system vendor identifier. This field should be programmed by BIOS during boot-up. Once written, this register becomes Read Only. This field can only be cleared by PLTRST#. Note: Register must be written as a DWord write with SID register. Datasheet Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.3.1.14 SID--Subsystem ID Register (IDER--D22:F2) Address Offset: 2Eh-2Fh Default Value: 8086h 23.3.1.15 Attribute: Size: Bit Description 15:0 Subsystem ID (SSID)--R/WO. Indicates the sub-system identifier. This field should be programmed by BIOS during boot-up. Once written, this register becomes Read Only. This field can only be cleared by PLTRST#. Note: Register must be written as a DWord write with SVID register. CAPP--Capabilities List Pointer Register (IDER--D22:F2) Address Offset: 34h Default Value: C8h 23.3.1.16 Attribute: Size: Description 7:0 Capability Pointer (CP)--R/WO. This field indicates that the first capability pointer is offset C8h (the power management capability). INTR--Interrupt Information Register (IDER--D22:F2) Bit 15:8 7:0 R/W, RO Size: 16 bits Description Interrupt Pin (IPIN)--RO. A value of 1h/2h/3h/4h indicates that this function implements legacy interrupt on INTA/INTB/INTC/INTD, respectively FunctionValueINTx (2 IDE)03hINTC Interrupt Line (ILINE)--R/W. The value written in this register indicates which input of the system interrupt controller, the device's interrupt pin is connected to. This value is used by the OS and the device driver, and has no affect on the hardware. PID--PCI Power Management Capability ID Register (IDER--D22:F2) Address Offset: C8-C9h Default Value: D001h Bit 15:8 7:0 Datasheet RO 8 bits Bit Address Offset: 3C-3Dh Attribute: Default Value: 0300h 23.3.1.17 R/WO 16 bits Attribute: Size: RO 16 bits Description Next Capability (NEXT)--RO. Its value of D0h points to the MSI capability. Cap ID (CID)--RO. This field indicates that this pointer is a PCI power management. 793 Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.3.1.18 PC--PCI Power Management Capabilities Register (IDER--D22:F2) Address Offset: CA-CBh Default Value: 0023h Bit 15:11 10:9 8:6 5 Description PME_Support (PSUP)--RO. This five-bit field indicates the power states in which the function may assert PME#. IDER can assert PME# from any D-state except D1 or D2 which are not supported by IDER. Reserved Aux_Current (AC)--RO. Reports the maximum Suspend well current required when in the D3cold state. Value of 000b is reported. Device Specific Initialization (DSI)--RO. Indicates whether device-specific initialization is required. Reserved 3 PME Clock (PMEC)--RO. Indicates that PCI clock is not required to generate PME#. Version (VS)--RO. Hardwired to 011b to indicate support for Revision 1.2 of the PCI Power Management Specification. PMCS--PCI Power Management Control and Status Register (IDER--D22:F2) Address Offset: CC-CFh Default Value: 00000000h Bit 31:4 Attribute: Size: RO, R/W 32 bits Description Reserved 3 No Soft Reset (NSR)--RO. 0 = Devices do perform an internal reset upon transitioning from D3hot to D0 using software control of the PowerState bits. Configuration Context is lost when performing the soft reset. Upon transition from the D3hot to the D0 state, full re-initialization sequence is needed to return the device to D0 Initialized. 1 = Devices do not perform an internal reset upon transitioning from D3hot to D0. Configuration Context is preserved. Upon transition from the D3hot to the D0 Initialized state, no additional operating system intervention is required to preserve Configuration Context beyond writing the PowerState bits. 2 Reserved 1:0 794 RO 16 bits 4 2:0 23.3.1.19 Attribute: Size: Power State (PS)--R/W. This field is used both to determine the current power state of the PT function and to set a new power state. The values are: 00 = D0 state 11 = D3HOT state When in the D3HOT state, the controller's configuration space is available, but the I/O and memory spaces are not. Additionally, interrupts are blocked. If software attempts to write a '10' or '01' to these bits, the write will be ignored. Datasheet Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.3.1.20 MID--Message Signaled Interrupt Capability ID Register (IDER--D22:F2) Address Offset: D0-D1h Default Value: 0005h Bit 15:8 7:0 23.3.1.21 Attribute: Size: Description Next Pointer (NEXT)--RO. This value indicates this is the last item in the capabilities list. Capability ID (CID)--RO. The Capabilities ID value indicates device is capable of generating an MSI. MC--Message Signaled Interrupt Message Control Register (IDER--D22:F2) Address Offset: D2-D3h Default Value: 0080h Bit 15:8 7 Attribute: Size: Description Reserved 64-bit Address Capable (C64)--RO. Capable of generating 64-bit and 32-bit messages. Multiple Message Enable (MME)--R/W. These bits are R/W for software compatibility, but only one message is ever sent by the PT function. 3:1 Multiple Message Capable (MMC)--RO. Only one message is required. MSI Enable (MSIE)--R/W. If set, MSI is enabled and traditional interrupt pins are not used to generate interrupts. MA--Message Signaled Interrupt Message Address Register (IDER--D22:F2) Address Offset: D4-D7h Default Value: 00000000h Bit 31:2 1:0 23.3.1.23 Attribute: Size: R/W, RO 32 bits Description Address (ADDR)--R/W. This field contains the Lower 32 bits of the system specified message address, always DWord aligned Reserved MAU--Message Signaled Interrupt Message Upper Address Register (IDER--D22:F2) Address Offset: D8-dBh Default Value: 00000000h Bit 31:4 3:0 Datasheet RO, R/W 16 bits 6:4 0 23.3.1.22 RO 16 bits Attribute: Size: RO, R/W 32 bits Description Reserved Address (ADDR)--R/W. This field contains the Upper 4 bits of the system specified message address. 795 Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.3.1.24 MD--Message Signaled Interrupt Message Data Register (IDER--D22:F2) Address Offset: DC-DDh Default Value: 0000h Attribute: Size: Bit 15:0 23.3.2 R/W 16 bits Description Data (DATA)--R/W. This content is driven onto the lower word of the data bus of the MSI memory write transaction. IDER BAR0 Registers Table 23-5. IDER BAR0 Register Address Map 796 Address Offset Register Symbol Default Value Attribute 0h IDEDATA IDE Data Register 00h R/W 1h 1h IDEERD1 IDE Error Register DEV1 00h R/W IDEERD0 IDE Error Register DEV0 00h R/W 1h IDEFR 2h IDESCIR 2h 2h Register Name IDE Features Register 00h R/W IDE Sector Count In Register 00h R/W IDESCOR1 IDE Sector Count Out Register Device 1 00h R/W IDESCOR0 IDE Sector Count Out Register Device 0 00h R/W 3h IDESNOR0 IDE Sector Number Out Register Device 0 00h R/W 3h IDESNOR1 IDE Sector Number Out Register Device 1 00h R/W 3h IDESNIR IDE Sector Number In Register 00h R/W 4h IDECLIR IDE Cylinder Low In Register 00h R/W 4h IDCLOR1 IDE Cylinder Low Out Register Device 1 00h R/W 4h IDCLOR0 IDE Cylinder Low Out Register Device 0 00h R/W 5h IDCHOR0 IDE Cylinder High Out Register Device 0 00h R/W 5h IDCHOR1 IDE Cylinder High Out Register Device 1 00h R/W 5h IDECHIR IDE Cylinder High In Register 00h R/W 6h IDEDHIR IDE Drive/Head In Register 00h R/W 6h IDDHOR1 IDE Drive Head Out Register Device 1 00h R/W 6h IDDHOR0 IDE Drive Head Out Register Device 0 00h R/W 7h IDESD0R IDE Status Device 0 Register 80h R/W 7h IDESD1R IDE Status Device 1 Register 80h R/W 7h IDECR IDE Command Register 00h R/W Datasheet Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.3.2.1 IDEDATA--IDE Data Register (IDER--D22:F2) Address Offset: 0h Default Value: 00h Attribute: Size: R/W 8 bits The IDE data interface is a special interface that is implemented in the HW. This data interface is mapped to I/O space from the host and takes read and write cycles from the host targeting master or slave device. Writes from host to this register result in the data being written to Intel ME memory. Reads from host to this register result in the data being fetched from Intel ME memory. Data is typically written/ read in WORDs. Intel ME FW must enable hardware to allow it to accept Host initiated Read/ Write cycles, else the cycles are dropped. 23.3.2.2 Bit Description 7:0 IDE Data Register (IDEDR)--R/W. Data Register implements the data interface for IDE. All writes and reads to this register translate into one or more corresponding write/reads to Intel ME memory. IDEERD1--IDE Error Register DEV1 (IDER--D22:F2) Address Offset: 01h Default Value: 00h Attribute: Size: R/W 8 bits This register implements the Error register of the command block of the IDE function. The register is read only by the HOST interface when DEV = 1 (slave device). Bit 7:0 23.3.2.3 Description IDE Error Data (IDEED)--R/W. Drive reflects its error/ diagnostic code to the host using this register at different times. IDEERD0--IDE Error Register DEV0 (IDER--D22:F2) Address Offset: 01h Default Value: 00h Attribute: Size: R/W 8 bits This register implements the Error register of the command block of the IDE function. The register is read only by the HOST interface when DEV = 0 (master device). Bit 7:0 Datasheet Description IDE Error Data (IDEED)--R/W. Drive reflects its error/ diagnostic code to the host using this register at different times. 797 Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.3.2.4 IDEFR--IDE Features Register (IDER--D22:F2) Address Offset: 01h Default Value: 00h Attribute: Size: R/W 8 bits This register implements the Feature register of the command block of the IDE function. This register can be written only by the Host. When the HOST reads the same address, it reads the Error register of Device 0 or Device 1 depending on the device_select bit (bit 4 of the drive/head register). Bit 7:0 23.3.2.5 Description IDE Feature Data (IDEFD)--R/W. IDE drive specific data written by the Host IDESCIR--IDE Sector Count In Register (IDER--D22:F2) Address Offset: 02h Default Value: 00h Attribute: Size: R/W 8 bits This register implements the Sector Count register of the command block of the IDE function. This register can be written only by the Host. When host writes to this register, all 3 registers (IDESCIR, IDESCOR0, IDESCOR1) are updated with the written value. A host read to this register address reads the IDE Sector Count Out Register IDESCOR0 if DEV=0 or IDESCOR1 if DEV=1 Bit 7:0 23.3.2.6 Description IDE Sector Count Data (IDESCD)--R/W. Host writes the number of sectors to be read or written. IDESCOR1--IDE Sector Count Out Register Device 1 Register (IDER--D22:F2) Address Offset: 02h Default Value: 00h Attribute: Size: R/W 8 bits This register is read by the HOST interface if DEV = 1. Intel ME Firmware writes to this register at the end of a command of the selected device. When the host writes to this address, the IDE Sector Count In Register (IDESCIR), this register is updated. Bit 7:0 798 Description IDE Sector Count Out Dev1 (ISCOD1)--R/W. Sector Count register for Slave Device (that is, Device 1) Datasheet Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.3.2.7 IDESCOR0--IDE Sector Count Out Register Device 0 Register (IDER--D22:F2) Address Offset: 02h Default Value: 00h Attribute: Size: R/W 8 bits This register is read by the HOST interface if DEV = 0. Intel ME Firmware writes to this register at the end of a command of the selected device. When the host writes to this address, the IDE Sector Count In Register (IDESCIR), this register is updated. 23.3.2.8 Bit Description 7:0 IDE Sector Count Out Dev0 (ISCOD0)--R/W. Sector Count register for Master Device (that is, Device 0). IDESNOR0--IDE Sector Number Out Register Device 0 Register (IDER--D22:F2) Address Offset: 03h Default Value: 00h Attribute: Size: R/W 8 bits This register is read by the Host if DEV = 0. Intel ME Firmware writes to this register at the end of a command of the selected device. When the host writes to the IDE Sector Number In Register (IDESNIR), this register is updated with that value. Bit 7:0 23.3.2.9 Description IDE Sector Number Out DEV 0 (IDESNO0)--R/W. Sector Number Out register for Master device. IDESNOR1--IDE Sector Number Out Register Device 1 Register (IDER--D22:F2) Address Offset: 03h Default Value: 00h Attribute: Size: R/W 8 bits This register is read by the Host if DEV = 1. Intel ME Firmware writes to this register at the end of a command of the selected device. When the host writes to the IDE Sector Number In Register (IDESNIR), this register is updated with that value. Bit 7:0 Datasheet Description IDE Sector Number Out DEV 1 (IDESNO1)--R/W. Sector Number Out register for Slave device. 799 Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.3.2.10 IDESNIR--IDE Sector Number In Register (IDER--D22:F2) Address Offset: 03h Default Value: 00h Attribute: Size: R/W 8 bits This register implements the Sector Number register of the command block of the IDE function. The register can be written only by the Host. When host writes to this register, all 3 registers (IDESNIR, IDESNOR0, IDESNOR1) are updated with the written value. Host read to this register address reads the IDE Sector Number Out Register IDESNOR0 if DEV=0 or IDESNOR1 if DEV=1. 23.3.2.11 Bit Description 7:0 IDE Sector Number Data (IDESND)--R/W. This register contains the number of the first sector to be transferred. IDECLIR--IDE Cylinder Low In Register (IDER--D22:F2) Address Offset: 04h Default Value: 00h Attribute: Size: R/W 8 bits This register implements the Cylinder Low register of the command block of the IDE function. The register can be written only by the Host. When host writes to this register, all 3 registers (IDECLIR, IDECLOR0, IDECLOR1) are updated with the written value. Host read to this register address reads the IDE Cylinder Low Out Register IDECLOR0 if DEV=0 or IDECLOR1 if DEV=1. Bit 7:0 23.3.2.12 Description IDE Cylinder Low Data (IDECLD)--R/W. Cylinder Low register of the command block of the IDE function. IDCLOR1--IDE Cylinder Low Out Register Device 1 Register (IDER--D22:F2) Address Offset: 04h Default Value: 00h Attribute: Size: R/W 8 bits This register is read by the Host if DEV = 1. Intel ME Firmware writes to this register at the end of a command of the selected device. When the host writes to the IDE Cylinder Low In Register (IDECLIR), this register is updated with that value. Bit 7:0 800 Description IDE Cylinder Low Out DEV 1. (IDECLO1)--R/W. Cylinder Low Out Register for Slave Device. Datasheet Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.3.2.13 IDCLOR0--IDE Cylinder Low Out Register Device 0 Register (IDER--D22:F2) Address Offset: 04h Default Value: 00h Attribute: Size: R/W 8 bits This register is read by the Host if DEV = 0. Intel ME Firmware writes to this register at the end of a command of the selected device. When the host writes to the IDE Cylinder Low In Register (IDECLIR), this register is updated with that value. 23.3.2.14 Bit Description 7:0 IDE Cylinder Low Out DEV 0. (IDECLO0)--R/W. Cylinder Low Out Register for Master Device. IDCHOR0--IDE Cylinder High Out Register Device 0 Register (IDER--D22:F2) Address Offset: 05h Default Value: 00h Attribute: Size: R/W 8 bits This register is read by the Host if DEVice = 0. Intel ME Firmware writes to this register at the end of a command of the selected device. When the host writes to the IDE Cylinder High In Register (IDECHIR), this register is updated with that value. 23.3.2.15 Bit Description 7:0 IDE Cylinder High Out DEV 0 (IDECHO0)--R/W. Cylinder High out register for Master device. IDCHOR1--IDE Cylinder High Out Register Device 1 Register (IDER--D22:F2) Address Offset: 05h Default Value: 00h Attribute: Size: R/W 8 bits This register is read by the Host if Device = 1. Intel ME Firmware writes to this register at the end of a command of the selected device. When the host writes to the IDE Cylinder High In Register (IDECHIR), this register is updated with that value. Bit 7:0 Datasheet Description IDE Cylinder High Out DEV 1 (IDECHO1)--R/W. Cylinder High out register for Slave device. 801 Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.3.2.16 IDECHIR--IDE Cylinder High In Register (IDER--D22:F2) Address Offset: 05h Default Value: 00h Attribute: Size: R/W 8 bits This register implements the Cylinder High register of the command block of the IDE function. The register can be written only by the Host. When host writes to this register, all 3 registers (IDECHIR, IDECHOR0, IDECHOR1) are updated with the written value. Host read to this register address reads the IDE Cylinder High Out Register IDECHOR0 if DEV=0 or IDECHOR1 if DEV=1. 23.3.2.17 Bit Description 7:0 IDE Cylinder High Data (IDECHD)--R/W. Cylinder High data register for IDE command block. IDEDHIR--IDE Drive/Head In Register (IDER--D22:F2) Address Offset: 06h Default Value: 00h Attribute: Size: R/W 8 bits This register implements the Drive/Head register of the command block of the IDE. The register can be written only by the Host. When host writes to this register, all 3 registers (IDEDHIR, IDEDHOR0, IDEDHOR1) are updated with the written value. Host read to this register address reads the IDE Drive/Head Out Register (IDEDHOR0) if DEV=0 or IDEDHOR1 if DEV=1. Bit 4 of this register is the DEV (master/slave) bit. This bit is cleared by hardware on IDE software reset (S_RST toggles to '1') in addition to Host system reset and D3->D0 transition of the function. Bit 7:0 802 Description IDE Drive/Head Data (IDEDHD)--R/W. Register defines the drive number, head number and addressing mode. Datasheet Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.3.2.18 IDDHOR1--IDE Drive Head Out Register Device 1 Register (IDER--D22:F2) Address Offset: 06h Default Value: 00h Attribute: Size: R/W 8 bits This register is read only by the Host. Host read to this Drive/head In register address reads the IDE Drive/Head Out Register (IDEDHOR0) if DEV=1 Bit 4 of this register is the DEV (master/slave) bit. This bit is cleared by hardware on IDE software reset (S_RST toggles to '1') in addition to the Host system reset and D3 to D0 transition of the IDE function. When the host writes to this address, it updates the value of the IDEDHIR register. Bit 7:0 23.3.2.19 Description IDE Drive Head Out DEV 1 (IDEDHO1)--R/W. Drive/Head Out register of Slave device. IDDHOR0--IDE Drive Head Out Register Device 0 Register (IDER--D22:F2) Address Offset: 06h Default Value: 00h Attribute: Size: R/W 8 bits This register is read only by the Host. Host read to this Drive/head In register address reads the IDE Drive/Head Out Register (IDEDHOR0) if DEV=0. Bit 4 of this register is the DEV (master/slave) bit. This bit is cleared by hardware on IDE software reset (S_RST toggles to 1) in addition to the Host system reset and D3 to D0 transition of the IDE function. When the host writes to this address, it updates the value of the IDEDHIR register. Bit 7:0 23.3.2.20 Description IDE Drive Head Out DEV 0 (IDEDHO0)--R/W. Drive/Head Out register of Master device. IDESD0R--IDE Status Device 0 Register (IDER--D22:F2) Address Offset: 07h Default Value: 80h Attribute: Size: R/W 8 bits This register implements the status register of the Master device (DEV = 0). The register is read only by the Host. Host read of this register clears the Master device's interrupt. When the HOST writes to the same address it writes to the command register The bits description is for ATA mode. Bit 7 Datasheet Description Busy (BSY)--R/W. This bit is set by HW when the IDECR is being written and DEV=0, or when SRST bit is asserted by Host or host system reset or D3-to-D0 transition of the IDE function. This bit is cleared by FW write of 0. 803 Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) Bit 6 23.3.2.21 Description Drive Ready (DRDY)--R/W. When set, this bit indicates drive is ready for command. 5 Drive Fault (DF)--R/W. Indicates Error on the drive. 4 Drive Seek Complete (DSC)--R/W. Indicates Heads are positioned over the desired cylinder. 3 Data Request (DRQ)--R/W. Set when, the drive wants to exchange data with the Host using the data register. 2 Corrected Data (CORR)--R/W. When set, this bit indicates a correctable read error has occurred. 1 Index (IDX)--R/W. This bit is set once per rotation of the medium when the index mark passes under the read/write head. 0 Error (ERR)--R/W. When set, this bit indicates an error occurred in the process of executing the previous command. The Error Register of the selected device contains the error information. IDESD1R--IDE Status Device 1 Register (IDER--D22:F2) Address Offset: 07h Default Value: 80h Attribute: Size: R/W 8 bits This register implements the status register of the slave device (DEV = 1). The register is read only by the Host. Host read of this register clears the slave device's interrupt. When the HOST writes to the same address it writes to the command register. The bits description is for ATA mode. Bit 804 Description 7 Busy (BSY)--R/W. This bit is set by hardware when the IDECR is being written and DEV=0, or when SRST bit is asserted by the Host or host system reset or D3-to-D0 transition of the IDE function. This bit is cleared by FW write of 0. 6 Drive Ready (DRDY)--R/W. When set, indicates drive is ready for command. 5 Drive Fault (DF)--R/W. Indicates Error on the drive. 4 Drive Seek Complete (DSC)--R/W. Indicates Heads are positioned over the desired cylinder. 3 Data Request (DRQ)--R/W. Set when the drive wants to exchange data with the Host using the data register. 2 Corrected Data (CORR)--R/W. When set indicates a correctable read error has occurred. 1 Index (IDX)--R/W. This bit is set once per rotation of the medium when the index mark passes under the read/write head. 0 Error (ERR)--R/W. When set, this bit indicates an error occurred in the process of executing the previous command. The Error Register of the selected device contains the error information Datasheet Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.3.2.22 IDECR--IDE Command Register (IDER--D22:F2) Address Offset: 07h Default Value: 00h Attribute: Size: R/W 8 bits This register implements the Command register of the command block of the IDE function. The register can be written only by the Host. When the HOST reads the same address it reads the Status register DEV0 if DEV=0 or Status Register DEV1 if DEV=1 (Drive/Head register bit [4]). 23.3.3 Bit Description 7:0 IDE Command Data (IDECD)--R/W. Host sends the commands (read/ write, and so on) to the drive using this register. IDER BAR1 Registers Table 23-6. IDER BAR1 Register Address Map 23.3.3.1 Address Offset Register Symbol 2h IDDCR 2h IDASR Default Value Attribute IDE Device Control Register 00h RO, WO IDE Alternate status Register 00h RO Register Name IDDCR--IDE Device Control Register (IDER--D22:F2) Address Offset: 2h Default Value: 00h Attribute: Size: WO 8 bits This register implements the Device Control register of the Control block of the IDE function. The register is Write only by the Host. When the HOST reads to the same address it reads the Alternate Status register. Bit 7:3 Datasheet Description Reserved 2 Software reset (S_RST)--WO. When this bit is set by the Host, it forces a reset to the device. 1 Host interrupt Disable (nIEN)--WO. When set, this bit disables hardware from sending interrupt to the Host. 0 Reserved 805 Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.3.3.2 IDASR--IDE Alternate Status Register (IDER--D22:F2) Address Offset: 2h Default Value: 00h Attribute: Size: RO 8 bits This register implements the Alternate Status register of the Control block of the IDE function. The register is a mirror register to the status register in the command block. Reading this register by the HOST does not clear the IDE interrupt of the DEV selected device Host read of this register when DEV=0 (Master), Host gets the mirrored data of IDESD0R register. Host read of this register when DEV=1 (Slave), host gets the mirrored data of IDESD1R register. 23.3.4 Bit Description 7:0 IDE Alternate Status Register (IDEASR)--RO. This field mirrors the value of the DEV0/ DEV1 status register, depending on the state of the DEV bit on Host reads. IDER BAR4 Registers Table 23-7. IDER BAR4 Register Address Map 806 Address Offset Register Symbol Default Value Attribute 0h IDEPBMCR IDE Primary Bus Master Command Register 00h RO, R/W 1h IDEPBMDS0R IDE Primary Bus Master Device Specific 0 Register 00h R/W 2h IDEPBMSR IDE Primary Bus Master Status Register 80h RO, R/W 3h IDEPBMDS1R IDE Primary Bus Master Device Specific 1 Register 00h R/W 4h IDEPBMDTPR0 IDE Primary Bus Master Descriptor Table Pointer Register Byte 0 00h R/W 5h IDEPBMDTPR1 IDE Primary Bus Master Descriptor Table Pointer Register Byte 1 00h R/W 6h IDEPBMDTPR2 IDE Primary Bus Master Descriptor Table Pointer Register Byte 2 00h R/W 7h IDEPBMDTPR3 IDE Primary Bus Master Descriptor Table Pointer Register Byte 3 00h R/W 8h IDESBMCR IDE Secondary Bus Master Command Register 00h RO, R/W 9h IDESBMDS0R IDE Secondary Bus Master Device Specific 0 Register 00h R/W Ah IDESBMSR IDE Secondary Bus Master Status Register 00h R/W, RO Bh IDESBMDS1R IDE Secondary Bus Master Device Specific 1 Register 00h R/W Ch IDESBMDTPR0 IDE Secondary Bus Master Descriptor Table Pointer Register Byte 0 00h R/W Dh IDESBMDTPR1 IDE Secondary Bus Master Descriptor Table Pointer Register Byte 1 00h R/W Eh IDESBMDTPR2 IDE Secondary Bus Master Descriptor Table Pointer Register Byte 2 00h R/W Fh IDESBMDTPR3 IDE Secondary Bus Master Descriptor Table Pointer Register Byte 3 00h R/W Register Name Datasheet Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.3.4.1 IDEPBMCR--IDE Primary Bus Master Command Register (IDER--D22:F2) Address Offset: 00h Default Value: 00h Attribute: Size: RO, R/W 8 bits This register implements the bus master command register of the primary channel. The register is programmed by the Host. Bit 7:4 3 2:1 0 23.3.4.2 Description Reserved Read Write Command (RWC)--R/W. This bit sets the direction of bus master transfer. 0 = Reads are performed from system memory 1 = Writes are performed to System Memory. This bit should not be changed when the bus master function is active. Reserved Start/Stop Bus Master (SSBM)--R/W. This bit gates the bus master operation of IDE function when 0. Writing 1 enables the bus master operation. Bus master operation can be halted by writing a 0 to this bit. Operation cannot be stopped and resumed. This bit is cleared after data transfer is complete as indicated by either the BMIA bit or the INT bit of the Bus Master status register is set or both are set. IDEPBMDS0R--IDE Primary Bus Master Device Specific 0 Register (IDER--D22:F2) Address Offset: 01h Default Value: 00h 23.3.4.3 Bit Description 7:0 Device Specific Data0 (DSD0)--R/W. Device Specific R/W 8 bits Attribute: Size: RO, R/W 8 bits IDEPBMSR--IDE Primary Bus Master Status Register (IDER--D22:F2) Address Offset: 02h Default Value: 80h Bit Description 7 Simplex Only (SO)--RO. Value indicates whether both Bus Master Channels can be operated at the same time or not. 0 = Both can be operated independently 1 = Only one can be operated at a time. 6 Drive 1 DMA Capable (D1DC)--R/W. This bit is read/write by the host (not write 1 clear). 5 Drive 0 DMA Capable (D0DC)--R/W. This bit is read/write by the host (not write 1 clear). 4:3 Datasheet Attribute: Size: Reserved 2 Interrupt (INT)--R/W. This bit is set by the hardware when it detects a positive transition in the interrupt logic (refer to IDE host interrupt generation diagram).The hardware will clear this bit when the Host SW writes 1 to it. 1 Error (ER)--R/W. Bit is typically set by FW. Hardware will clear this bit when the Host SW writes 1 to it. 0 Bus Master IDE Active (BMIA)--RO. This bit is set by hardware when SSBM register is set to 1 by the Host. When the bus master operation ends (for the whole command) this bit is cleared by firmware. This bit is not cleared when the HOST writes 1 to it. 807 Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.3.4.4 IDEPBMDS1R--IDE Primary Bus Master Device Specific 1 Register (IDER--D22:F2) Address Offset: 03h Default Value: 00h Bit 7:0 23.3.4.5 Attribute: Size: Description Device Specific Data1 (DSD1)--R/W. Device Specific Data. IDEPBMDTPR0--IDE Primary Bus Master Descriptor Table Pointer Byte 0 Register (IDER--D22:F2) Address Offset: 04h Default Value: 00h Bit 7:0 23.3.4.6 Attribute: Size: Descriptor Table Pointer Byte 0 (DTPB0)--R/W. This register implements the Byte 0 (1 of 4 bytes) of the descriptor table Pointer (four I/O byte addresses) for bus master operation of the primary channel. This register is read/write by the HOST interface. IDEPBMDTPR1--IDE Primary Bus Master Descriptor Table Pointer Byte 1 Register (IDER--D22:F2) Bit 7:0 Attribute: Size: Descriptor Table Pointer Byte 1 (DTPB1)--R/W. This register implements the Byte 1 (of four bytes) of the descriptor table Pointer (four I/O byte addresses) for bus master operation of the primary channel. This register is programmed by the Host. IDEPBMDTPR2--IDE Primary Bus Master Descriptor Table Pointer Byte 2 Register (IDER--D22:F2) Attribute: Size: R/W 8 bits Bit Description 7:0 Descriptor Table Pointer Byte 2 (DTPB2)--R/W. This register implements the Byte 2 (of four bytes) of the descriptor table Pointer (four I/O byte addresses) for bus master operation of the primary channel. This register is programmed by the Host. IDEPBMDTPR3--IDE Primary Bus Master Descriptor Table Pointer Byte 3 Register (IDER--D22:F2) Address Offset: 07h Default Value: 00h 808 R/W 8 bits Description Address Offset: 06h Default Value: 00h 23.3.4.8 R/W 8 bits Description Address Offset: 05h Default Value: 00h 23.3.4.7 R/W 8 bits Attribute: Size: R/W 8 bits Bit Description 7:0 Descriptor Table Pointer Byte 3 (DTPB3)--R/W. This register implements the Byte 3 (of four bytes) of the descriptor table Pointer (four I/O byte addresses) for bus master operation of the primary channel. This register is programmed by the Host. Datasheet Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.3.4.9 IDESBMCR--IDE Secondary Bus Master Command Register (IDER--D22:F2) Address Offset: 08h Default Value: 00h Bit 7:4 3 2:1 0 23.3.4.10 Attribute: Size: Description Reserved Read Write Command (RWC)--R/W. This bit sets the direction of bus master transfer. When 0, Reads are performed from system memory; when 1, writes are performed to System Memory. This bit should not be changed when the bus master function is active. Reserved Start/Stop Bus Master (SSBM)--R/W. This bit gates the bus master operation of IDE function when zero. Writing 1 enables the bus master operation. Bus master operation can be halted by writing a 0 to this bit. Operation cannot be stopped and resumed. This bit is cleared after data transfer is complete as indicated by either the BMIA bit or the INT bit of the Bus Master status register is set or both are set. IDESBMDS0R--IDE Secondary Bus Master Device Specific 0 Register (IDER--D22:F2) Address Offset: 09h Default Value: 00h 23.3.4.11 Attribute: Size: R/W 8 bits Bit Description 7:0 Device Specific Data0 (DSD0)--R/W. This register implements the bus master Device Specific 1 register of the secondary channel. This register is programmed by the Host. IDESBMSR--IDE Secondary Bus Master Status Register (IDER--D22:F2) Address Offset: 0Ah Default Value: 80h Attribute: Size: R/W, RO 8 bits Bit Description 7 Simplex Only (SO)--R/W. This bit indicates whether both Bus Master Channels can be operated at the same time or not. 0 = Both can be operated independently 1 = Only one can be operated at a time. 6 Drive 1 DMA Capable (D1DC)--R/W. This bit is read/write by the host. 5 4:0 Datasheet R/W 8 bits Drive 0 DMA Capable (D0DC)--R/W. This bit is read/write by the host. Reserved 809 Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.3.4.12 IDESBMDS1R--IDE Secondary Bus Master Device Specific 1 Register (IDER--D22:F2) Address Offset: 0Bh Default Value: 00h 23.3.4.13 Attribute: Size: Bit Description 7:0 Device Specific Data1 (DSD1)--R/W. This register implements the bus master Device Specific 1 register of the secondary channel. This register is programmed by the Host for device specific data if any. IDESBMDTPR0--IDE Secondary Bus Master Descriptor Table Pointer Byte 0 Register (IDER--D22:F2) Address Offset: 0Ch Default Value: 00h Bit 7:0 23.3.4.14 Attribute: Size: Descriptor Table Pointer Byte 0 (DTPB0)--R/W. This register implements the Byte 0 (1 of 4 bytes) of the descriptor table Pointer (four I/O byte addresses) for bus master operation of the secondary channel. This register is read/write by the HOST interface. IDESBMDTPR1--IDE Secondary Bus Master Descriptor Table Pointer Byte 1 Register (IDER--D22:F2) Bit 7:0 Attribute: Size: R/W 8 bits Description Descriptor Table Pointer Byte 1 (DTPB1)--R/W. This register implements the Byte 1 (of four bytes) of the descriptor table Pointer (four I/O byte addresses) for bus master operation of the secondary channel. This register is programmed by the Host. IDESBMDTPR2--IDE Secondary Bus Master Descriptor Table Pointer Byte 2 Register (IDER--D22:F2) Address Offset: 0Eh Default Value: 00h Bit 7:0 810 R/W 8 bits Description Address Offset: 0Dh Default Value: 00h 23.3.4.15 R/W 8 bits Attribute: Size: R/W 8 bits Description Descriptor Table Pointer Byte 2 (DTPB2)--R/W. This register implements the Byte 2 (of four bytes) of the descriptor table Pointer (four I/O byte addresses) for bus master operation of the secondary channel. This register is programmed by the Host. Datasheet Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.3.4.16 IDESBMDTPR3--IDE Secondary Bus Master Descriptor Table Pointer Byte 3 Register (IDER--D22:F2) Address Offset: 0Fh Default Value: 00h Attribute: Size: Bit 7:0 R/W 8 bits Description Descriptor Table Pointer Byte 3 (DTPB3)--R/W. This register implements the Byte 3 (of four bytes) of the descriptor table Pointer (four I/O byte addresses) for bus master operation of the secondary channel. This register is programmed by the Host. 23.4 Serial Port for Remote Keyboard and Text (KT) Redirection (KT--D22:F3) 23.4.1 PCI Configuration Registers (KT--D22:F3) Table 23-8. Serial Port for Remote Keyboard and Text (KT) Redirection Register Address Map Address Offset Datasheet Register Symbol Register Name Default Value Attribute 00h-01h VID Vendor Identification 8086h RO 02h-03h DID Device Identification See Register description RO 04h-05h CMD Command Register 0000h RO, R/W 06h-07h STS Device Status 00B0h RO 08h RID Revision ID See Register description RO 09h-0Bh CC Class Codes 070002h RO 0Ch CLS 00h RO 10h-13h KTIBA KT IO Block Base Address Cache Line Size 00000001h RO, R/W 14h-17h KTMBA KT Memory Block Base Address 2Ch-2Dh SVID 00000000h RO, R/W Subsystem Vendor ID 0000h R/WO 8086h R/WO C8h RO 2Eh-2Fh SID Subsystem ID 34h CAP Capabilities Pointer 3Ch-3Dh INTR Interrupt Information 0200h R/W, RO C8h-C9h PID PCI Power Management Capability ID D001h RO CAh-CBh PC PCI Power Management Capabilities 0023h RO D0h-D1h MID Message Signaled Interrupt Capability ID 0005h RO D2h-D3h MC Message Signaled Interrupt Message Control 0080h RO, R/W D4h-D7h MA Message Signaled Interrupt Message Address 00000000h RO, R/W D8h-dBh MAU Message Signaled Interrupt Message Upper Address 00000000h RO, R/W DCh-DDh MD 0000h R/W Message Signaled Interrupt Message Data 811 Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.4.1.1 VID--Vendor Identification Register (KT--D22:F3) Address Offset: 00-01h Default Value: 8086h Bit 15:0 23.4.1.2 Attribute: Size: Description Vendor ID (VID)--RO. This is a 16-bit value assigned by Intel. DID--Device Identification Register (KT--D22:F3) Address Offset: 02-03h Default Value: See bit description 23.4.1.3 Attribute: Size: Description 15:0 Device ID (DID)--RO. This is a 16-bit value assigned to the PCH KT controller. See Section 1.3 for the value of the DID Register. CMD--Command Register (KT--D22:F3) Bit 15:11 Attribute: Size: RO, R/W 16 bits Description Reserved 10 Interrupt Disable (ID)--R/W. This bit disables pin-based INTx# interrupts. This bit has no effect on MSI operation. 1 = Internal INTx# messages will not be generated. 0 = Internal INTx# messages are generated if there is an interrupt and MSI is not enabled. 9:3 Reserved 2 Bus Master Enable (BME)--R/W. This bit controls the KT function's ability to act as a master for data transfers. This bit does not impact the generation of completions for split transaction commands. For KT, the only bus mastering activity is MSI generation. 1 Memory Space Enable (MSE)--R/W. This bit controls Access to the PT function's target memory space. 0 I/O Space enable (IOSE)--R/W. This bit controls access to the PT function's target I/O space. STS--Device Status Register (KT--D22:F3) Address Offset: 06-07h Default Value: 00B0h Bit 15:11 10:9 8:5 Attribute: Size: RO 16 bits Description Reserved DEVSEL# Timing Status (DEVT)--RO. This field controls the device select time for the PT function's PCI interface. Reserved 4 Capabilities List (CL)--RO. This bit indicates that there is a capabilities pointer implemented in the device. 3 Interrupt Status (IS)--RO. This bit reflects the state of the interrupt in the function. Setting of the Interrupt Disable bit to 1 has no affect on this bit. Only when this bit is a 1 and ID bit is 0 is the INTB interrupt asserted to the Host. 2:0 812 RO 16 bits Bit Address Offset: 04-05h Default Value: 0000h 23.4.1.4 RO 16 bits Reserved Datasheet Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.4.1.5 RID--Revision ID Register (KT--D22:F3) Address Offset: 08h Default Value: See bit description 23.4.1.6 Attribute: Size: Bit Description 7:0 Revision ID--RO. This field indicates the device specific revision identifier. See Section 1.3 for the value of the RID Register. CC--Class Codes Register (KT--D22:F3) Address Offset: 09-0Bh Default Value: 070002h Bit 23:16 15:8 7:0 23.4.1.7 RO 8 bits Attribute: Size: RO 24 bits Description Base Class Code (BCC)--RO This field indicates the base class code of the KT host controller device. Sub Class Code (SCC)--RO This field indicates the sub class code of the KT host controller device. Programming Interface (PI)--RO This field indicates the programming interface of the KT host controller device. CLS--Cache Line Size Register (KT--D22:F3) Address Offset: 0Ch Default Value: 00h Attribute: Size: RO 8 bits This register defines the system cache line size in DWord increments. Mandatory for master which use the Memory-Write and Invalidate command. Bit 7:0 23.4.1.8 Description Cache Line Size (CLS)--RO. All writes to system memory are Memory Writes. KTIBA--KT IO Block Base Address Register (KT--D22:F3) Address Offset: 10-13h Default Value: 00000001h Bit 31:16 15:3 2:1 0 Datasheet Attribute: Size: RO, R/W 32 bits Description Reserved Base Address (BAR)--R/W. This field provides the base address of the I/O space (8 consecutive I/O locations). Reserved Resource Type Indicator (RTE)--RO. This bit indicates a request for I/O space 813 Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.4.1.9 KTMBA--KT Memory Block Base Address Register (KT--D22:F3) Address Offset: 14-17h Default Value: 00000000h Bit 31:12 11:4 3 23.4.1.10 Attribute: Size: Description Base Address (BAR)--R/W. This field provides the base address for Memory Mapped I,O BAR. Bits 31:12 correspond to address signals 31:12. Reserved Prefetchable (PF)--RO. This bit indicates that this range is not prefetchable. 2:1 Type (TP)--RO. This field indicates that this range can be mapped anywhere in 32-bit address space. 0 Resource Type Indicator (RTE)--RO. This bit indicates a request for register memory space. SVID--Subsystem Vendor ID Register (KT--D22:F3) Address Offset: 2Ch-2Dh Default Value: 0000h Bit 15:0 Attribute: Size: Subsystem Vendor ID (SSVID)--R/WO. Indicates the sub-system vendor identifier. This field should be programmed by BIOS during boot-up. Once written, this register becomes Read Only. This field can only be cleared by PLTRST#. Register must be written as a DWord write with SID register. SID--Subsystem ID Register (KT--D22:F3) Address Offset: 2Eh-2Fh Default Value: 8086h Attribute: Size: R/WO 16 bits Bit Description 15:0 Subsystem ID (SSID)--R/WO. Indicates the sub-system identifier. This field should be programmed by BIOS during boot-up. Once written, this register becomes Read Only. This field can only be cleared by PLTRST#. Note: 23.4.1.12 R/WO 16 bits Description Note: 23.4.1.11 RO, R/W 32 bits Register must be written as a DWord write with SVID register. CAP--Capabilities Pointer Register (KT--D22:F3) Address Offset: 34h Default Value: C8h Attribute: Size: RO 8 bits This optional register is used to point to a linked list of new capabilities implemented by the device. Bit 7:0 814 Description Capability Pointer (CP)--RO. This field indicates that the first capability pointer is offset C8h (the power management capability). Datasheet Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.4.1.13 INTR--Interrupt Information Register (KT--D22:F3) Address Offset: 3C-3Dh Default Value: 0200h Bit 15:8 7:0 23.4.1.14 Attribute: Size: Description Interrupt Pin (IPIN)--RO. A value of 1h/2h/3h/4h indicates that this function implements legacy interrupt on INTA/INTB/INTC/INTD, respectively FunctionValueINTx (3 KT/Serial Port)02hINTB Interrupt Line (ILINE)--R/W. The value written in this register tells which input of the system interrupt controller, the device's interrupt pin is connected to. This value is used by the OS and the device driver, and has no affect on the hardware. PID--PCI Power Management Capability ID Register (KT--D22:F3) Address Offset: C8-C9h Default Value: D001h Bit 15:8 7:0 23.4.1.15 Attribute: Size: RO 16 bits Description Next Capability (NEXT)--RO. A value of D0h points to the MSI capability. Cap ID (CID)--RO. This field indicates that this pointer is a PCI power management. PC--PCI Power Management Capabilities ID Register (KT--D22:F3) Address Offset: CA-CBh Default Value: 0023h Bit 15:11 10:6 5 Attribute: Size: RO 16 bits Description PME Support (PME)--RO.This field indicates no PME# in the PT function. Reserved Device Specific Initialization (DSI)--RO. This bit indicates that no device-specific initialization is required. 4 Reserved 3 PME Clock (PMEC)--RO. This bit indicates that PCI clock is not required to generate PME# 2:0 Datasheet R/W, RO 16 bits Version (VS)--RO. This field indicates support for the PCI Power Management Specification, Revision 1.2. 815 Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.4.1.16 MID--Message Signaled Interrupt Capability ID Register (KT--D22:F3) Address Offset: D0-D1h Default Value: 0005h Attribute: Size: RO 16 bits Message Signaled Interrupt is a feature that allows the device/function to generate an interrupt to the host by performing a DWord memory write to a system specified address with system specified data. This register is used to identify and configure an MSI capable device. Bit 15:8 7:0 23.4.1.17 Description Next Pointer (NEXT)--RO. This value indicates this is the last item in the list. Capability ID (CID)--RO. This field value of Capabilities ID indicates device is capable of generating MSI. MC--Message Signaled Interrupt Message Control Register (KT--D22:F3) Address Offset: D2-D3h Default Value: 0080h Bit 15:8 7 RO, R/W 16 bits Description Reserved 64-bit Address Capable (C64)--RO. Capable of generating 64-bit and 32-bit messages. 6:4 Multiple Message Enable (MME)--R/W.These bits are R/W for software compatibility, but only one message is ever sent by the PT function. 3:1 Multiple Message Capable (MMC)--RO. Only one message is required. 0 23.4.1.18 Attribute: Size: MSI Enable (MSIE)--R/W. If set, MSI is enabled and traditional interrupt pins are not used to generate interrupts. MA--Message Signaled Interrupt Message Address Register (KT--D22:F3) Address Offset: D4-D7h Default Value: 00000000h Attribute: Size: RO, R/W 32 bits This register specifies the DWord aligned address programmed by system software for sending MSI. Bit 31:2 1:0 816 Description Address (ADDR)--R/W. Lower 32 bits of the system specified message address, always DWord aligned. Reserved Datasheet Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.4.1.19 MAU--Message Signaled Interrupt Message Upper Address Register (KT--D22:F3) Address Offset: D8-dBh Default Value: 00000000h Attribute: Size: Bit 31:4 3:0 23.4.1.20 RO, R/W 32 bits Description Reserved Address (ADDR)--R/W. Upper 4 bits of the system specified message address. MD--Message Signaled Interrupt Message Data Register (KT--D22:F3) Address Offset: DC-DDh Default Value: 0000h Attribute: Size: R/W 16 bits This 16-bit field is programmed by system software if MSI is enabled Bit 15:0 23.4.2 Description Data (DATA)--R/W. This MSI data is driven onto the lower word of the data bus of the MSI memory write transaction. KT IO/Memory Mapped Device Registers Table 23-9. KT IO/Memory Mapped Device Register Address Map Datasheet Address Offset Register Symbol 0h KTRxBR Default Value Attribute KT Receive Buffer Register 00h RO Register Name 0h KTTHR KT Transmit Holding Register 00h WO 0h KTDLLR KT Divisor Latch LSB Register 00h R/W KT Interrupt Enable register 00h R/W, RO KT Divisor Latch MSB Register 00h R/W 1h KTIER 1h KTDLMR 2h KTIIR KT Interrupt Identification register 00h RO 2h KTFCR KT FIFO Control register 00h WO 3h KTLCR KT Line Control register 03h R/W 4h KTMCR KT Modem Control register 00h RO, R/W 5h KTLSR KT Line Status register 00h RO 6h KTMSR KT Modem Status register 00h RO 817 Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.4.2.1 KTRxBR--KT Receive Buffer Register (KT--D22:F3) Address Offset: 00h Default Value: 00h Attribute: Size: RO 8 bits This implements the KT Receiver Data register. Host access to this address, depends on the state of the DLAB bit (KTLCR[7]). It must be 0 to access the KTRxBR. RxBR: Host reads this register when FW provides it the receive data in non-FIFO mode. In FIFO mode, host reads to this register translate into a read from Intel ME memory (RBR FIFO). Bit 7:0 23.4.2.2 Description Receiver Buffer Register (RBR)--RO. Implements the Data register of the Serial Interface. If the Host does a read, it reads from the Receive Data Buffer. KTTHR--KT Transmit Holding Register (KT--D22:F3) Address Offset: 00h Default Value: 00h Attribute: Size: RO 8 bits This implements the KT Transmit Data register. Host access to this address, depends on the state of the DLAB bit (KTLCR[7]). It must be 0 to access the KTTHR. THR: When host wants to transmit data in the non-FIFO mode, it writes to this register. In FIFO mode, writes by host to this address cause the data byte to be written by hardware to Intel ME memory (THR FIFO). Bit 7:0 23.4.2.3 Description Transmit Holding Register (THR)--WO. Implements the Transmit Data register of the Serial Interface. If the Host does a write, it writes to the Transmit Holding Register. KTDLLR--KT Divisor Latch LSB Register (KT--D22:F3) Address Offset: 00h Default Value: 00h Attribute: Size: R/W 8 bits This register implements the KT DLL register. Host can Read/Write to this register only when the DLAB bit (KTLCR[7]) is 1. When this bit is 0, Host accesses the KTTHR or the KTRBR depending on Read or Write. This is the standard Serial Port Divisor Latch register. This register is only for software compatibility and does not affect performance of the hardware. Bit 7:0 818 Description Divisor Latch LSB (DLL)--R/W. Implements the DLL register of the Serial Interface. Datasheet Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.4.2.4 KTIER--KT Interrupt Enable Register (KT--D22:F3) Address Offset: 01h Default Value: 00h Attribute: Size: R/W 8 bits This implements the KT Interrupt Enable register. Host access to this address, depends on the state of the DLAB bit (KTLCR[7]). It must be "0" to access this register. The bits enable specific events to interrupt the Host. Bit 7:4 23.4.2.5 Description Reserved 3 MSR (IER2)--R/W. When set, this bit enables bits in the Modem Status register to cause an interrupt to the host. 2 LSR (IER1)--R/W.When set, this bit enables bits in the Receiver Line Status Register to cause an Interrupt to the Host. 1 THR (IER1)--R/W. When set, this bit enables an interrupt to be sent to the Host when the transmit Holding register is empty. 0 DR (IER0)--R/W. When set, the Received Data Ready (or Receive FIFO Timeout) interrupts are enabled to be sent to Host. KTDLMR--KT Divisor Latch MSB Register (KT--D22:F3) Address Offset: 01h Default Value: 00h Attribute: Size: R/W 8 bits Host can Read/Write to this register only when the DLAB bit (KTLCR[7]) is 1. When this bit is 0, Host accesses the KTIER. This is the standard Serial interface's Divisor Latch register's MSB. This register is only for SW compatibility and does not affect performance of the hardware. Bit 7:0 23.4.2.6 Description Divisor Latch MSB (DLM)--R/W. Implements the Divisor Latch MSB register of the Serial Interface. KTIIR--KT Interrupt Identification Register (KT--D22:F3) Address Offset: 02h Default Value: 00h Attribute: Size: RO 8 bits The KT IIR register prioritizes the interrupts from the function into 4 levels and records them in the IIR_STAT field of the register. When Host accesses the IIR, hardware freezes all interrupts and provides the priority to the Host. Hardware continues to monitor the interrupts but does not change its current indication until the Host read is over. Table in the Host Interrupt Generation section shows the contents. Bit 7 FIFO Enable (FIEN1)--RO. This bit is connected by hardware to bit 0 in the FCR register. 6 FIFO Enable (FIEN0)--RO. This bit is connected by hardware to bit 0 in the FCR register. 5:4 Datasheet Description Reserved 819 Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) Bit Description 3:1 IIR STATUS (IIRSTS)--RO. These bits are asserted by the hardware according to the source of the interrupt and the priority level. 0 23.4.2.7 Interrupt Status (INTSTS)--RO. 0 = Pending interrupt to Host 1 = No pending interrupt to Host KTFCR--KT FIFO Control Register (KT--D22:F3) Address Offset: 02h Default Value: 00h Attribute: Size: WO 8 bits When Host writes to this address, it writes to the KTFCR. The FIFO control Register of the serial interface is used to enable the FIFOs, set the receiver FIFO trigger level and clear FIFOs under the direction of the Host. When Host reads from this address, it reads the KTIIR. Bit 23.4.2.8 Description 7:6 Receiver Trigger Level (RTL)--WO. Trigger level in bytes for the RCV FIFO. Once the trigger level number of bytes is reached, an interrupt is sent to the Host. 00 = 01 01 = 04 10 = 08 11 = 14 5:3 Reserved 2 XMT FIFO Clear (XFIC)--WO. When the Host writes one to this bit, the hardware will clear the XMT FIFO. This bit is self-cleared by hardware. 1 RCV FIFO Clear (RFIC)--WO. When the Host writes one to this bit, the hardware will clear the RCV FIFO. This bit is self-cleared by hardware. 0 FIFO Enable (FIE)--WO.When set, this bit indicates that the KT interface is working in FIFO node. When this bit value is changed the RCV and XMT FIFO are cleared by hardware. KTLCR--KT Line Control Register (KT--D22:F3) Address Offset: 03h Default Value: 03h Attribute: Size: R/W 8 bits The line control register specifies the format of the asynchronous data communications exchange and sets the DLAB bit. Most bits in this register have no affect on hardware and are only used by the FW. Bit Description 7 Divisor Latch Address Bit (DLAB)--R/W. This bit is set when the Host wants to read/write the Divisor Latch LSB and MSB Registers. This bit is cleared when the Host wants to access the Receive Buffer Register or the Transmit Holding Register or the Interrupt Enable Register. 6 Break Control (BC)--R/W. This bit has no affect on hardware. 5:4 3 Parity Enable (PE)--R/W.This bit has no affect on hardware. 2 Stop Bit Select (SBS)--R/W. This bit has no affect on hardware. 1:0 820 Parity Bit Mode (PBM)--R/W. This bit has no affect on hardware. Word Select Byte (WSB)--R/W. This bit has no affect on hardware. Datasheet Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.4.2.9 KTMCR--KT Modem Control Register (KT--D22:F3) Address Offset: 04h Default Value: 00h Attribute: Size: R/W 8 bits The Modem Control Register controls the interface with the modem. Since the FW emulates the modem, the Host communicates to the FW using this register. Register has impact on hardware when the Loopback mode is on. Bit 7:5 23.4.2.10 Description Reserved 4 Loop Back Mode (LBM)--R/W. When set by the Host, this bit indicates that the serial port is in loop Back mode. This means that the data that is transmitted by the host should be received. Helps in debug of the interface. 3 Output 2 (OUT2)--R/W. This bit has no affect on hardware in normal mode. In loop back mode the value of this bit is written by hardware to the Modem Status Register bit 7. 2 Output 1 (OUT1)--R/W. This bit has no affect on hardware in normal mode. In loop back mode the value of this bit is written by hardware to Modem Status Register bit 6. 1 Request to Send Out (RTSO)--R/W. This bit has no affect on hardware in normal mode. In loopback mode, the value of this bit is written by hardware to Modem Status Register bit 4. 0 Data Terminal Ready Out (DRTO)--R/W. This bit has no affect on hardware in normal mode. In loopback mode, the value in this bit is written by hardware to Modem Status Register Bit 5. KTLSR--KT Line Status Register (KT--D22:F3) Address Offset: 05h Default Value: 00h Attribute: Size: WO 8 bits This register provides status information of the data transfer to the Host. Error indication, and so on are provided by the HW/FW to the host using this register. Bit Description 7 RX FIFO Error (RXFER)--RO. This bit is cleared in non FIFO mode. This bit is connected to BI bit in FIFO mode. 6 Transmit Shift Register Empty (TEMT)--RO. This bit is connected by HW to bit 5 (THRE) of this register. 5 Transmit Holding Register Empty (THRE)--RO. This bit is always set when the mode (FIFO/ Non-FIFO) is changed by the Host. This bit is active only when the THR operation is enabled by the FW. This bit has acts differently in the different modes: Non FIFO: This bit is cleared by hardware when the Host writes to the THR registers and set by hardware when the FW reads the THR register. FIFO mode: This bit is set by hardware when the THR FIFO is empty, and cleared by hardware when the THR FIFO is not empty. This bit is reset on Host system reset or D3->D0 transition. 4 Break Interrupt (BI)--RO. This bit is cleared by hardware when the LSR register is being read by the Host. 3:2 Datasheet Reserved 1 Overrun Error (OE): This bit is cleared by hardware when the LSR register is being read by the Host. The FW typically sets this bit, but it is cleared by hardware when the host reads the LSR. 0 Data Ready (DR)--RO. Non-FIFO Mode: This bit is set when the FW writes to the RBR register and cleared by hardware when the RBR register is being Read by the Host. FIFO Mode: This bit is set by hardware when the RBR FIFO is not empty and cleared by hardware when the RBR FIFO is empty. This bit is reset on Host System Reset or D3->D0 transition. 821 Intel(R) Management Engine (Intel(R) ME) Subsystem Registers (D22:F[3:0]) 23.4.2.11 KTMSR--KT Modem Status Register (KT--D22:F3) Address Offset: 06h Default Value: 00h Attribute: Size: RO 8 bits The functionality of the Modem is emulated by the FW. This register provides the status of the current state of the control lines from the modem. Bit Description 7 Data Carrier Detect (DCD)--RO. In Loop Back mode this bit is connected by hardware to the value of MCR bit 3. 6 Ring Indicator (RI)--RO. In Loop Back mode this bit is connected by hardware to the value of MCR bit 2. 5 Data Set Ready (DSR)--RO. In Loop Back mode this bit is connected by hardware to the value of MCR bit 0. 4 Clear To Send (CTS)--RO. In Loop Back mode this bit is connected by hardware to the value of MCR bit 1. 3 Delta Data Carrier Detect (DDCD)--RO. This bit is set when bit 7 is changed. This bit is cleared by hardware when the MSR register is being read by the HOST driver. 2 Trailing Edge of Read Detector (TERI)--RO. This bit is set when bit 6 is changed from 1 to 0. This bit is cleared by hardware when the MSR register is being read by the Host driver. 1 Delta Data Set Ready (DDSR)--RO. This bit is set when bit 5 is changed. This bit is cleared by hardware when the MSR register is being read by the Host driver. 0 Delta Clear To Send (DCTS)--RO. This bit is set when bit 4 is changed. This bit is cleared by hardware when the MSR register is being read by the Host driver. 822 Datasheet