Photologic(R) Dual Channel Encoder OPBA301, OPBA303 Features: Dual channel outputs for Quadrature output Open collector inverter outputs 0.010" (0.254 mm) sensor apertures for high resolution Snap mount Product Photo Here Description: The OPBA301 and OPBA303 device consists of an infrared emitting diode and a monolithic integrated circuit which incorporates two independent photodiodes, linear amplifiers, Schmitt trigger circuits and output transistors. The OPBA301 features a dual TTL output that is compatible with TTL/LSTTL and can drive 8 TTL loads. The OPBA303 has a 10K pull-up output with EMI protection on each channel. Applications include linear and rotary encoders with high resolution provided by internal 0.010" (0.254 mm) apertures located in front of the Photologic(R) sensor on 0.040" (1.02 mm) center line spacing. Custom electrical design, wire length and connectors are available. Contact your local representative or OPTEK for more information. Applications: Ordering Information Mechanical switch replacement Speed and direction indication Mechanical limit indication Rotary encoders Edge sensing Sliding door automotive and Part Number LED Peak Wavelength OPBA301 Sensor Output Slot Width / Depth Aperture Emitter/Sensor Wire Length 0.200" / 0.350" 0.05" / 0.01" 24" 22 AWG Flat Dual TTL 890 nm OPBA303 10K Pull-Up liftgate applications OPBA301 VREG AMP OPBA303 4-Vcc 4-Vcc VREG 10K 3-Out B AMP 3-Out B 0.01f AMP 2-Out A AMP 1-GND 10K 2-Out A 0.01f 1-GND OPTEK Technology is TS 16949:2002 certified, any changes will be consistent with TS 16949:2002 procedures. OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue B 02/13 Page 1 of 5 Photologic(R) Dual Channel Encoder OPBA301, OPBA303 OPBA301, OPBA303 B A Pin # Description 1 Output-A 2 Output-B 3 VCC 4 Ground CONTAINS POLYSULFONE To avoid stress cracking, we suggest using ND Industries' Vibra-Tite for thread-locking. Vibra-Tite evaporates fast without causing structural failure in OPTEK's molded plastics. Absolute Maximum Ratings (TA = 25 C unless otherwise noted) Storage & Operating Temperature Range -40C to +85 C Input Diode Forward DC Current 50 mA Reverse DC Voltage 2.0 V (1) 100 mW Supply Voltage, VCC 5.5 V Voltage at Output OPBA301 OPBA303 18 V 5.5V Power Dissipation Output Photologic(R) Power Dissipation(2) 200 mW Sinking Output Current DIMENSIONS ARE IN: 40 mA [ MILLIMETERS] INCHES OPTEK Technology is TS 16949:2002 certified, any changes will be consistent with TS 16949:2002 procedures. Issue B 02/13 Page 2 of 5 OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Photologic(R) Dual Channel Encoder OPBA301, OPBA303 Electrical Characteristics (TA = 25 C unless otherwise noted) SYMBOL PARAMETER MIN TYP MAX UNITS 4.5 - 5.5 V TEST CONDITIONS Input Diode Supply Voltage VCC Output Photologic(R) Sensor ICCL Supply Current Both Outputs Low (both photodiodes irradiated) - 25.5 29 mA Unblocked condition (no load on output) ICCH Supply Current Both Outputs High (both photodiodes shaded) - 20.5 23 mA Blocked condition (no load on output) ICCM Supply Current Mixed Output States (one high, one low) - 23 - mA 1 blocked condition 1 unblocked condition IOH High Level Output Current - 1 30 A VOH = 16 V (blocked condition) VOL Low Level Output Voltage - 0.21 0.40 V IOL = 12.8 mA (unblocked condition) Propagation Delay Output High to Low Output Low to High - 2 10 - s s VCC = 5 V, RL = 360 , f = 10 kHz, DC = 50% Output Rise Time Output Fall Time - 20 5 - ns ns RL = 360 tPHL, tPLH tr, tf Performance Curves Low Level Output vs Ambient Temperature High Level Output vs Ambient Temperature 33 VCC = 4.5 V IOL = 12.8 mA = 890 nm EE = 0.5 mW/cm2 Low Level Output Current - V OL 0.4 15 10 5 VCC = 5 V No Load on Output = 890 nm 31 Supply C urrent - I CC L , I CC H (m A) (volts) mW/cm2 20 OH (nA) VCC = 4.5 V VOH = 18 V EE = 0 High Level Output Current - I Supply Current vs Ambient Temperature 0.5 25 0.3 VOL 0.2 29 27 25 ICCL 23 ICCH 21 0.1 19 IOH 17 0 0 0 -50 -25 0 25 50 TA - Ambient Temperature (C) 75 100 -50 -25 0 25 50 75 100 TA - Ambient Temperature (C) -50 -25 0 25 50 75 100 TA - Ambient Temperature (C) OPTEK Technology is TS 16949:2002 certified, any changes will be consistent with TS 16949:2002 procedures. OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue B 02/13 Page 3 of 5 Photologic(R) Dual Channel Encoder OPBA301, OPBA303 Performance Curves Rise and Fall Time vs Ambient Temperature vs Output Load Propagation Delay vs Ambient Temperature 20 250 VCC = 5 V = 890 nm f = 10 kHz t r, R L = 2 K Propagation Delay - t P H L , t P LH (s) Switching Tim e - t r, t f (ns) 200 Amplitude = 0.5 mW/cm2 VCC = 5 V RL = 360 = 890 nm f = 10 kHz Duty Cycle = 50% 150 Amplitude = 0.5 mW/cm2 t r, R L = 1 K 100 50 15 10 tPHL 5 tPLH tr, RL = 360 tf, RL = 360 , 1 k , 2 k 0 -50 -25 0 25 50 75 0 100 -50 -25 TA - Ambient Temperature (C) 0 25 50 75 100 TA - Ambient Temperature (C) Ideal Target Size & Spacing For Linear or Circular Targets Sensor Output(s) Ch-A 0.09 [2.20] Clear Hole Ch-B 0.09 [2.20] Clear Hole 0.07 [1.80] Clear Hole 0.07 [1.80] 0.06 [1.50] MIN. 0.07 [1.80] 1-1 0-1 0-0 1-0 1-1 0-1 0-0 1-0 Dimensions are in inches [mm] Please consult OPTEK for target design and sensor location relative to the target. OPTEK Technology is TS 16949:2002 certified, any changes will be consistent with TS 16949:2002 procedures. Issue B 02/13 Page 4 of 5 OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Photologic(R) Dual Channel Encoder OPBA301, OPBA303 Issue Approval Date Initial Release Tom Osborne 2/03/06 A.1 Minor changes to the first paragraph on page 1 Tom Osborne 3/29/06 A.2 Changed part numbers OPBA301 & OPBA302 on page 2 Tom Osborne 4/10/06 A.3 Added new DIMENSIONS statement and repositioned items on the pages to match other data sheets. Used smaller new logo. Fixed minor typos on page 2. A.4 Removed OPBA300, OPBA302, changed verbiage to accommodate the change, removed Package 1. A Change Description 07/28/06 Tom Osborne 02/21/2013 OPTEK Technology is TS 16949:2002 certified, any changes will be consistent with TS 16949:2002 procedures. OPTEK Technology Inc. -- 1645 Wallace Drive, Carrollton, Texas 75006 Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 sensors@optekinc.com www.optekinc.com Issue B 02/13 Page 5 of 5