RP30-2412DEW - Recom International Power

244 www.recom-international.comApril-2005

30 Watt

Single &&

Dual

Output

POWERLINE

DC/DC-Converter

RP30-

S_DEW

Series

●4:1 Wide Input Voltage Range

●30 Watts Output Power

●1.6kVDC Isolation

●Fixed Operating Frequency

●Six-Sided Continuous Shield

●International Safety Standard Approvals

●Standard 50.8 x40.6x10.2mm Package

●Efficiency to 88%

Features

Selection Guide 24V and 48V Input Types

Part Number Input Output Output Input (4) Efficiency(5) Capacitive(6)

Range Voltage Current Current Load max.

VDC VDC mA mA % µF

RP30-241.5SEW 10-40 1.5 8000 658 80 65000

RP30-241.8SEW 10-40 1.8 8000 759 83 65000

RP30-242.5SEW 10-40 2.5 8000 1029 85 33000

RP30-243.3SEW 10-40 3.3 6000 994 87 19500

RP30-2405SEW 10-40 5 6000 1506 87 10200

RP30-2412SEW 10-40 12 2500 1506 87 3300

RP30-2415SEW 10-40 15 2000 1488 88 1100

RP30-481.5SEW 18-75 1.5 8000 329 80 65000

RP30-481.8SEW 18-75 1.8 8000 380 83 65000

RP30-482.5SEW 18-75 2.5 8000 508 86 33000

RP30-483.3SEW 18-75 3.3 6000 497 87 19500

RP30-4805SEW 18-75 5 6000 744 88 10200

RP30-4812SEW 18-75 12 2500 753 87 3300

RP30-4815SEW 18-75 15 2000 744 88 1100

RP30-2412DEW 10-40 ±12 ±1250 1543 85 ±1000

RP30-2415DEW 10-40 ±15 ±1000 1524 86 ±680

RP30-4812DEW 18-75 ±12 ±1250 762 86 ±1000

RP30-4815DEW 18-75 ±15 ±1000 753 87 ±680

The EW-Series of DC/DC Converters are fully certified to EN 60950: 2000.

This makes them ideal for all

Telecom and safety applications where approved isolation is required.

Description

www.recom-international.com 245

April-2005

Specifications (typical at nominal input and 25°C unless otherwise noted)

Input Voltage Range 24V nominal input 10-40VDC

48V nominal input 18-75VDC

Under Voltage Lockout 24V input DC-DC ON 10VDC

DC-DC OFF 8VDC

48V input DC-DC ON 18VDC

DC-DC OFF 16VDC

Input Filter (see note 1) L-C Type

Input Voltage Variation dv/dt (Complies with ETS300 132 part 4.4) 5V/ms max

Input Surge Voltage (100 ms max.) 24V Input 50VDC

48V Input 100VDC

Input Reflected Ripple (nominal Vin and full load) 20mAp-p

Start Up Time (nominal Vin and constant resistor load) 10ms typ.

Remote ON/OFF (see note 7) DC-DC ON Open or 3.5V < Vr < 12V

DC-DC OFF Short or 0V < Vr < 1.2V

Remote OFF input current Nominal input 2.5mA

Output Power 30W max.

continued on next page

Derating-Graph (Ambient Temperature)

POWERLINE

DC/DC-Converter RP30-S_DEW

Series

125

100

Ambient Temperature Range (°C)

-25 -10 0 50 60 80 90 100

Output Power (%)

Natural Convection

-40 70

125

100

Ambient Temperature Range (°C)

-25 -10 0 50 60 70 80 90 100

Output Power (%)

Natural Convection

-40

75°C

RP30-243.3SEW RP30-243.3SEW With Heat Sink

Intput Voltage (V)

Efficiency (%)

15 3020 25 35 40

Efficiency VS Input Voltage

Output Load (A)

Efficiency (%)

25634

Efficiency VS Output Load

RP30-483.3SEW RP30-483.3SEW

Typical Characteristics

Derating graphes are valid only for the shown part numbers. If you need detailed derating-information about a

part-number not shown here please contact our technical customer service at info@recom-development.at

246 www.recom-international.comApril-2005

Specifications (typical at nominal input and 25°C unless otherwise noted)

POWERLINE

DC/DC-Converter RP30-S_DEW

Series

Output Voltage Accuracy (full Load and nominal Vin) ±1%

Voltage Adjustability ±10%

Minimum Load Single 0%

Dual 10% of FL

Line Regulation (LL-HL at full load) ±0.5%

Load Regulation (25% to 100% FL) Single ±0.5%

Dual ±1%

Cross Regulation (Note 9) ±5%

Ripple and Noise (20MHz bandwith) Single 1.5, 1.8, 2.5, 3.3V 60mVp-p

(Measured with a 1004pF/50V MLCC) Single 5V 75mVp-p

Single 12, 15V 100mVp-p

Dual 5, 12, 15V 100mVp-p

Temperature Coefficient ±0.02%/°C, max.

Transient Response (25% load step change) 300µS

Over Voltage Protection 1.5, 1.8, 2.5, 3.3V 3.9V

Zener diode clamp (only single) 5V 6.2V

12V 15V

15V 18V

Over Load Protection (% of full load at nominal Vin) 150% typ

Short Circuit Protection Hiccup, automatic recovery

Efficiency see „Selection Guide“ table

Isolation Voltage 1.600VDC min.

Isolation Resistance 109Ωmin.

Isolation Capacitance 1000pF max.

Operating Frequency 300kHz typ.

Approved to Safety Standards EN60950

Operating Temperature Range -40°C to +85°C(with derating)

Maximum Case Temperature +100°C

Storage Temperature Range -55°C to +105°C

Over Temperature Protection 115°C typ.

Thermal Impedance Natural convection 10°C/Watt

Natural convection with Heat Sink 8.24°C/Watt

Thermal Shock MIL-STD-810D

Vibration 10-55Hz, 2G, 30 Min. along X, Y and Z

Relative Humidity 5% to 95% RH

Case Material Nickel-Coated copper

Base Material Non-conductive black plastic

Potting Material Epoxy (UL94-V0)

Conducted Emissions EN55022 Class A

Radiated Emissions EN55022 Class A

ESD EN61000-4-2 Perf. Criteria 2

Radiated Immunity EN61000-4-3 Perf. Criteria 2

Fast Transient EN61000-4-4 Perf. Criteria 2

Surge EN61000-4-5 Perf. Criteria 2

Conducted Immunity EN61000-4-6 Perf. Criteria 2

continued on next page

www.recom-international.com 247

April-2005

Specifications (typical at nominal input and 25°C unless otherwise noted)

POWERLINE

DC/DC-Converter RP30-S_DEW

Series

Weight 48g

Dimensions 50.8 x 40.6 x 10.2mm

MTBF (see note 2) 1.315 x 106Hours

Notes :

Package Style and Pinning (mm)

50.80

5.10

15.20

17.80

40.60

45.70

12.70

10.20

17.80

10.20

5.6

10.20

dia.

1.0

Bottom View

3rd angle

projection

Pin Pitch Tolerance ±0.35 mm

Pin Connections

Pin # Single Dual

1 +Vin +Vin

2 -Vin -Vin

4 CTRL CTRL

5 No Pin +Vout

6 +Vout Com

7 -Vout -Vout

8 Trim Trim

Trim Up

Trim Down

7(7)

8(8)

6(5)

External Output Trimming

Output can be externally trimmed by using the method

shown below.

( ) for dual output trim

1. An external filter capacitor is required for normal operation. The capacitor should be capable of handing 1A ripple current for 48V/24V models.

RECOM suggest: Nippon chemi-con KMF series, 220µF/100V, ESR 90m Ω.

2. BELLCORE TR-NWT-000332. Case l: 50% Stress, Temperature at 40°C (Ground fixed and controlled environment).

3. Simulated source impedance of 12uH. 12uH inductor in series with +Vin.

4. Maximum value at nominal input voltage and full load of standard type.

5. Typical value at nominal input voltage and full load.

6. Test by minimum Vin and constant resistor load.

7. The ON/OFF control function can be positive or negative logic. The pin voltage is referenced to negative input.

Positive logic ON/OFF is standard, no suffix (Ex. RP30-2405SEW)

Negative logic ON/OFF is marked with suffix-N (Ex. RP30-2405SEW/N).

8. Heat sink is optional and P/N: 7G-0011A.

9. The dual output required a minimum 10% loading on the output to maintain specified regulation. Operation under no-load condition will not damage

these devices, however they may not meet all listed specification.

10.See application notes for EMI-filtering.