© Semiconductor Components Industries, LLC, 2006
May, 2017 Rev. 7
1Publication Order Number:
MT9V032/D
MT9V032
MT9V032 1/3‐Inch Wide
VGA CMOS Digital Image
Sensor
Table 1. KEY PERFORMANCE PARAMETERS
Parameter Value
Optical Format 1/3-inch
Active Imager Size 4.51 mm (H) × 2.88 mm (V)
5.35 mm diagonal
Active Pixels 752H × 480 V
Pixel Size 6.0 mm × 6.0 mm
Color Filter Array Monochrome or color RGB Bayer
Pattern
Shutter Type Global Shutter
Maximum Data Rate Master Clock 26.6 MPS/26.6 MHz
Full Resolution 752 x 480
Frame Rate 60 fps (at full resolution)
ADC Resolution 10bit columnparallel
Responsivity 4.8 V/luxsec (550 nm)
Dynamic Range >55 dB;
>80 dB100dB in HDR mode
Supply Voltage 3.3 V ±0.3 V (all supplies)
Power Consumption <320 mW at maximum data rate;
100 mW standby Power
Operating Temperature 30°C to + 70°C
Packaging 48Pin CLCC
Features
Array Format: WideVGA, Active 752H x 480V (360,960 Pixels)
Global Shutter Photodiode Pixels; Simultaneous Integration And
Readout
Monochrome Or Color: Near_IR Enhanced Performance For Use
With NonVisible NIR Illumination
Readout Modes: Progressive Or Interlaced
Shutter Efficiency: >99%
Simple TwoWire Serial Interface
Register Lock Capability
Window Size: User Programmable To Any Smaller Format (QVGA,
CIF, QCIF, etc.). Data Rate Can Be Maintained Independent Of
Window Size
Binning: 2 x 2 And 4 x 4 Of The Full Resolution
ADC: OnChip, 10bit ColumnParallel (Option To Operate In
12bit To 10bit Companding Mode)
Automatic Controls: Auto Exposure Control (AEC) And Auto Gain
Control (AGC); Variable Regional And Variable Weight AEC/AGC
www.onsemi.com
See detailed ordering and shipping information on page2 of
this data sheet.
ORDERING INFORMATION
Support For Four Unique Serial Control
Register IDs To Control Multiple Imagers
On The Same Bus
Data Output Formats:
Single Sensor Mode:
10bit Parallel/StandAlone
8bit Or 10bit Serial LVDS
Stereo Sensor Mode:
Interspersed 8bit Serial LVDS
Applications
Security
High Dynamic Range Imaging
Unattended Surveillance
Stereo Vision
Video As Input
Machine Vision
Automation
CLCC48 11.43 × 11.43
CASE 848AQ
MT9V032
www.onsemi.com
2
Table of Contents
Ordering Information 3
General Description 4
Pixel Data Format 8
Color Device Limitations 9
Output Data Format 10
Serial Bus Description 12
TwoWire Serial Interface Sample Read and Write Sequences 14
Registers 16
Feature Description 31
OnChip Biases 34
Window Control 35
Blanking Control 36
Pixel Integration Control 37
Gain settings 40
Read Mode Options 45
Electrical Specifications 50
Temperature Reference 55
Appendix A Serial Configurations 57
Appendix B PowerOn Reset and Standby Timing 60
MT9V032
www.onsemi.com
3
ORDERING INFORMATION
Table 2. AVAILABLE PART NUMBERS
Part Number Product Description Orderable Product Attribute Description †
MT9V032C12STCD3GEVK 48pin CLCC demo3 kit (color)
MT9V032C12STCDGEVK 48pin CLCC demo kit (color)
MT9V032C12STCDP 48pin CLCC (color) Dry Pack with Protective Film
MT9V032C12STCDR 48pin CLCC (color) Dry Pack without Protective Film
MT9V032C12STCHGEVB 48pin CLCC headboard only (color)
MT9V032C12STCTP 48pin CLCC (color) Tape & Reel with Protective Film
MT9V032C12STMDGEVK 48pin CLCC demo kit (mono)
MT9V032C12STMDP 48pin CLCC (mono) Dry Pack with Protective Film
MT9V032C12STMDR 48pin CLCC (mono) Dry Pack without Protective Film
MT9V032C12STMHGEVB 48pin CLCC headboard only (mono)
MT9V032C12STMTP 48pin CLCC (mono) Tape & Reel with Protective Film
For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specification Brochure, BRD8011/D.
See the ON Semiconductor Device Nomenclature
document (TND310/D) for a full description of the naming
convention used for image sensors. For reference
documentation, including information on evaluation kits,
please visit our web site at www.onsemi.com.
MT9V032
www.onsemi.com
4
GENERAL DESCRIPTION
The ON Semiconductor MT9V032 is a 1/3inch
wideVGA format CMOS activepixel digital image sensor
with global shutter and high dynamic range (HDR)
operation. The sensor has specifically been designed to
support the demanding interior and exterior surveillance
imaging needs, which makes this part ideal for a wide
variety of imaging applications in realworld environments.
This wideVGA CMOS image sensor features ON
Semiconductors breakthrough lownoise CMOS imaging
technology that achieves CCD image quality (based on
signaltonoise ratio and lowlight sensitivity) while
maintaining the inherent size, cost, and integration
advantages of CMOS.
The active imaging pixel array is 752H x 480V. It
incorporates sophisticated camera functions onchip—such
as binning 2 x 2 and 4 x 4, to improve sensitivity when
operating in smaller resolutions—as well as windowing,
column and row mirroring. It is programmable through a
simple twowire serial interface.
The MT9V032 can be operated in its default mode or be
programmed for frame size, exposure, gain setting, and
other parameters. The default mode outputs a
wideVGAsize image at 60 frames per second (fps).
An onchip analogtodigital converter (ADC) provides
10 bits per pixel. A 12bit resolution companded for 10 bits
for small signals can be alternatively enabled, allowing more
accurate digitization for darker areas in the image.
In addition to a traditional, parallel logic output the
MT9V032 also features a serial lowvoltage differential
signaling (LVDS) output. The sensor can be operated in a
stereocamera, and the sensor, designated as a
stereomaster, is able to merge the data from itself and the
stereoslave sensor into one serial LVDS stream.
Control Register
Timing and Control
Digital Processing
Analog Processing
ADCs
ActivePixel
Sensor (APS)
Array
752H x 480 V
Slave Video LVDS in
(for stereo applications only)
Serial Video
LVDS Out
Parallel
Video
Data Out
Serial
Register
I/O
Figure 1. Block Diagram
MT9V032
www.onsemi.com
5
Figure 2. 48-Pin CLCC Pinout Diagram
123456 44 43
19 20 21 22 23 24 25 26 27 28 29 30
7
8
9
10
11
12
13
14
15
16
17
18
42
41
40
39
38
37
36
35
34
33
32
31
48 47 46 45
LVDSGND
BYPASS_CLKIN_N
LINE_VALID
FRAME_VALID
SDATA
S_STRL_ADRO
NC
VAA
STANDBY
S_CTRL_ADR1
VDDLVDS
DGND
DOUT0
BYPASS_CLKIN_P
SER_DATAIN_N
SER_DATAIN_P
LVDSGND
DGND
VDD
DOUT5
DOUT6
DOUT7
DOUT8
SER_DATAOUT_N
SER_DATAOUT_P
SHFT_CLKOUT_N
SHFT_CLKOUT_P
VDD
SYSCLK
PIXCLK
DOUT1
DOUT2
DOUT3
DOUT4
VAAPIX
AGND
NC
VAA
AGND
RESET#
DOUT9
STLN_OUT
EXPOSURE
SCLK
STFRM_OUT
LED_OUT
OE
RSVD
Table 3. PIN DESCRIPTIONS (Only pins DOUT0 through DOUT9 may be tristated)
48Pin LLCC
Numbers Symbol Type Descriptions Note
29 RSVD Input Connect to DGND. 1
10 SER_DATAIN_N Input Serial data in for stereoscopy (differential negative). Tie to 1kW pull
up (to 3.3V) in nonstereoscopy mode.
11 SER_DATAIN_P Input Serial data in for stereoscopy (differential positive). Tie to DGND in
nonstereoscopy mode.
8 BYPASS_CLKIN_N Input Input bypass shiftCLK (differential negative). Tie to 1KW pullup (to
3.3V) in nonstereoscopy mode.
9 BYPASS_CLKIN_P Input Input bypass shiftCLK (differential positive). Tie to DGND in non
stereoscopy mode.
23 EXPOSURE Input Rising edge starts exposure in slave mode.
25 SCLK Input Twowire serial interface clock. Connect to VDD with 1.5K resistor
even when no other twowire serial interface peripheral is attached.
28 OE Input DOUT enable pad, active HIGH. 2
30 S_CTRL_ADR0 Input Twowire serial interface slave address bit 3.
31 S_CTRL_ADR1 Input Twowire serial interface slave address bit 5.
32 RESET# Input Asynchronous reset. All registers assume defaults.
33 STANDBY Input Shut down sensor operation for power saving.
MT9V032
www.onsemi.com
6
Table 3. PIN DESCRIPTIONS (Only pins DOUT0 through DOUT9 may be tristated)
48Pin LLCC
Numbers NoteDescriptionsTypeSymbol
47 SYSCLK Input Master clock (26.6 MHz).
24 SDATA I/O Twowire serial interface data. Connect to VDD with 1.5K resistor
even when no other twowire serial interface peripheral is attached.
22 STLN_OUT I/O Output in master modestart line sync to drive slave chip in
phase; input in slave mode.
26 STFRM_OUT I/O Output in master modestart frame sync to drive a slave chip in
phase; input in slave mode.
20 LINE_VALID Output Asserted when DOUT data is valid.
21 FRAME_VALID Output Asserted when DOUT data is valid.
15 DOUT5 Output Parallel pixel data output 5.
16 DOUT6 Output Parallel pixel data output 6.
17 DOUT7 Output Parallel pixel data output 7.
18 DOUT8 Output Parallel pixel data output 8
19 DOUT9 Output Parallel pixel data output 9.
27 LED_OUT Output LED strobe output.
41 DOUT4 Output Parallel pixel data output 4.
42 DOUT3 Output Parallel pixel data output 3.
43 DOUT2 Output Parallel pixel data output 2.
44 DOUT1 Output Parallel pixel data output 1.
45 DOUT0 Output Parallel pixel data output 0.
46 PIXCLK Output Pixel clock out. DOUT is valid on rising edge of this clock.
2 SHFT_CLKOUT_N Output Output shift CLK (differential negative).
3 SHFT_CLKOUT_P Output Output shift CLK (differential positive).
4 SER_DATAOUT_N Output Serial data out (differential negative).
5 SER_DATAOUT_P Output Serial data out (differential positive).
1, 14 VDD Supply Digital power 3.3V.
35, 39 VAA Supply Analog power 3.3V.
40 VAAPIX Supply Pixel power 3.3V.
6 VDDLVDS Supply Dedicated power for LVDS pads.
7, 12 LVDSGND Ground Dedicated GND for LVDS pads.
13, 48 DGND Ground Digital GND.
34, 38 AGND Ground Analog GND.
36, 37 NC NC No connect. 3
1. Pin 29 (RSVD) must be tied to GND
2. Output Enable (OE) tristates signals DOUT0–DOUT9. No other signals are tristated with OE.
3. No connect. These pins must be left floating for proper operation.
MT9V032
www.onsemi.com
7
Master Clock
STANDBY from
Controller or
Digital GND
TwoWire
Serial Interface
SYSCLK
OE
RESET#
EXPOSURE
STANDBY
S_CTRL_ADR0
S_CTRL_ADR1
SCLK
SDATA
RSVD LVDSGND
DOUT(9:0
)
DGND AGND
LINE_VALID
FRAME_VALID
PIXCLK
LED_OUT
ERROR
To Controller
To LED Output
VDDLVDS VDD
VDD
VAA
VAA VAAPIX
VAAPIX
10KW
1.5KW
0.1mF
Figure 3. Typical Configuration (Connection)Parallel Output Mode
NOTE: LVDS signals are to be left floating.
VDD
VDD VAA
VAA
VDDLVDS
DOUT(9:0)
Master Clock
STANDBY from
Controller or
Digital GND
TwoWire
Serial Interface
SYSCLK
OE
RESET#
EXPOSURE
STANDBY
S_CTRL_ADR0
S_CTRL_ADR1
SCLK
SDATA
RSVD LVDSGND
DOUT(9:0
)
DGND AGND
LINE_VALID
FRAME_VALID
PIXCLK
LED_OUT
ERROR
To Controller
To LED Output
VDDLVDS VDD
VDD
VAA
VAA VAAPIX
VAAPIX
10KW
1.5KW
0.1mF
NOTE: LVDS signals are to be left floating.
VDD
VDD VAA
VAA
VDDLVDS
DOUT(9:0)
DGND
MT9V032
www.onsemi.com
8
PIXEL DATA FORMAT
Pixel Array Structure
The MT9V032 pixel array is configured as 782 columns
by 492 rows, shown in Figure 4. The left 26 columns and the
top eight rows of pixels are optically black and can be used
to monitor the black level. The black row data is used
internally for the automatic black level adjustment.
However, the middle four black rows can also be read out by
setting the sensor to raw data output mode. There are 753
columns by 481 rows of optically active pixels. The active
area is surrounded with optically transparent dummy
columns and rows to improve image uniformity within the
active area. One additional active column and active row are
used to allow horizontally and vertically mirrored readout to
also start on the same color pixel.
8 dark, 1 light dummy rows
2 dummy rows
2 dummy
columns
26 dark, 1 light
dummy columns
(0.0)
(782,492)
Figure 4. Pixel Array Description
Pixel
(2,9)
.
.
.
.
.
.
G
B
G
B
G
B
R
G
R
G
R
G
G
B
G
B
G
B
R
G
R
G
R
G
G
B
G
B
G
B
R
G
R
G
R
G
G
B
G
B
G
B
Figure 5. Pixel Color Pattern Detail (Top Right Corner)
Column Readout Direction
Row
Readout
Direction
R
G
R
G
R
G
MT9V032
www.onsemi.com
9
COLOR DEVICE LIMITATIONS
The color version of the MT9V032 does not support or
offers reduced performance for the following
functionalities.
Pixel Binning
Pixel binning is done on immediate neighbor pixels only;
no facility is provided to skip pixels according to a Bayer
pattern. Therefore, the result of binning combines pixels of
different colors. For more information, see “Pixel Binning”.
Interlaced Readout
Interlaced readout yields one field consisting only of red
and green pixels and another consisting only of blue and
green pixels. This is due to the Bayer pattern of the CFA.
Automatic Black Level Calibration
When the color bit is set (R0x0F[2]=1), the sensor uses
GREEN1 pixels black level correction value, which is
applied to all colors. To use calibration value based on all
dark pixels offset values, the color bit should be cleared.
Other Limiting Factors
Black level correction and rowwise noise correction are
applied uniformly to each color. Automatic exposure and
gain control calculations are made based on all three colors,
not just the green luma channel. High dynamic range does
operate; however, ON Semiconductor strongly recommends
limiting use to linear operation if good color fidelity is
required.
MT9V032
www.onsemi.com
10
OUTPUT DATA FORMAT
The MT9V032 image data can be read out in a progressive
scan or interlaced scan mode. Valid image data is surrounded
by horizontal and vertical blanking, as shown in Figure 6.
The amount of horizontal and vertical blanking is
programmable through R0x05 and R0x06, respectively.
LINE_VALID is HIGH during the shaded region of the
figure. See “Output Data Timing” for the description of
FRAME_VALID timing.
VALID iMAGE HORIZONTAL
BLANKING
VERTICAL/HORIZONTAL
BLANKING
VERTICAL BLANKING
00 00 00 ………… 00 00 00
00 00 00 ………… 00 00 00
00 00 00 ………… 00 00 00
00 00 00 ………… 00 00 00
00 00 00 ………… 00 00 00
00 00 00 ………… 00 00 00
00 00 00 ………… 00 00 00
00 00 00 ………… 00 00 00
00 00 00 ………… 00 00 00
00 00 00 ………… 00 00 00
00 00 00 ………… 00 00 00
00 00 00 ………… 00 00 00
P0,0 P0,1 P0,2…………P0,n1 P0,n
P1,0 P1,1 P1,2…………P1,n1 P1,n
Pm1,0 Pm1,1…………Pm1,n1 Pm1,n
Pm,0 Pm,1…………Pm,n1 Pm,n
Figure 6. Spatial Illustration of Image Readout
Output Data Timing
The data output of the MT9V032 is synchronized with the
PIXCLK output. When LINE_VALID is HIGH, one 10bit
pixel datum is output every PIXCLK period.
LINE_VALID
PIXCLK
Blanking Valide Image Data Blanking
P0
(9:0) P1
(9:0) P2
(9:0) P3
(9:0) P4
(9:0)
Pn1
(9:0)
Pn
(9:0)
Figure 7. Timing Example of Pixel Data
DOUT(9:0)
The PIXCLK is a nominally inverted version of the master
clock (SYSCLK). This allows PIXCLK to be used as a clock
to latch the data. However, when column bin 2 is enabled, the
PIXCLK is HIGH for one complete master clock master
period and then LOW for one complete master clock period;
when column bin 4 is enabled, the PIXCLK is HIGH for two
complete master clock periods and then LOW for two
complete master clock periods. It is continuously enabled,
even during the blanking period. Setting R0x74 bit[4] = 1
causes the MT9V032 to invert the polarity of the PIXCLK.
The parameters P1, A, Q, and P2 in Figure 8 are defined
in Table 4.
MT9V032
www.onsemi.com
11
Figure 8. Row Timing and FRAME_VALID/LINE_VALID Signals
P1 A QA QAP2
FRAME_VALID
LINE_VALID
...
...
...
Number of master clocks
Table 4. FRAME TIME LARGER THAN ONE FRAME
Parameter Name Equation Default Timing at 26.66 MHz
AActive data time R0x04 752 pixel clocks
= 752 master = 28.20ms
P1 Frame start blanking R0x05 23 71 pixel clocks
= 71master = 2.66ms
P2 Frame end blanking 23 (fixed) 23 pixel clocks
= 23 master = 0.86ms
QHorizontal blanking R0x05 94 pixel clocks
= 94 master = 3.52ms
A+Q Row time R0x04 + R0x05 846 pixel clocks
= 846 master = 31.72ms
VVertical blanking (R0x06) x (A + Q) + 4 38,074 pixel clocks
= 38,074 master = 1.43ms
Nrows x (A + Q) Frame valid time (R0x03) × (A + Q) 406,080 pixel clocks
= 406,080 master = 15.23ms
FTotal frame time V + (Nrows x (A + Q)) 444,154 pixel clocks
= 444,154 master = 16.66ms
Sensor timing is shown above in terms of pixel clock and
master clock cycles (refer to Figure 7). The recommended
master clock frequency is 26.66 MHz. The vertical blanking
and total frame time equations assume that the number of
integration rows (bits 11 through 0 of R0x0B) is less than the
number of active rows plus blanking rows minus overhead
rows (R0x03 + R0x06 2). If this is not the case, the number
of integration rows must be used instead to determine the
frame time, as shown in Table 5. In this example it is
assumed that R0x0B is programmed with 523 rows. For
Simultaneous Mode, if the exposure time register (0x0B)
exceeds the total readout time, then vertical blanking is
internally extended automatically to adjust for the additional
integration exposure time required. This extended value is
not written back to R0x06 (vertical blanking). R0x06 can be
used to adjust frame to frame readout time. This register
does not affect the exposure time but it may extend the
readout time.
Table 5. FRAME TIME LONG INTEGRATION TIME
Parameter Name
Equation
(Number of Master Clock Cycles) Default Timing at 26.66 MHz
V’ Vertical blanking (long integration
time) (R0x0B + 2 R0x03) × (A + Q) + 4 38,074 pixel clocks
= 38,074 master = 1.43ms
F” Total frame time (long integration
exposure time) (R0x0B + 2) × (A + Q) + 4 444,154 pixel clocks
= 444,154 master = 16.66ms
4. The MT9V032 uses column parallel analogtodigital converters, thus short row timing is not possible. The minimum total row time is 660
columns (horizontal width + horizontal blanking). The minimum horizontal blanking is 43. When the window width is set below 617, horizontal
blanking must be increased. The frame rate will not increase for row times less than 660 columns.
MT9V032
www.onsemi.com
12
SERIAL BUS DESCRIPTION
Registers are written to and read from the MT9V032
through the twowire serial interface bus. The MT9V032 is
a serial interface slave with four possible IDs (0x90, 0x98,
0xB0,and 0xB8) determined by the S_CTRL_ADR0 and
S_CTRL_ADR1 input pins. Data is transferred into the
MT9V032 and out through the serial data (SDATA) line. The
SDATA line is pulled up to VDD offchip by a 1.5KW resistor.
Either the slave or master device can pull the SDATA line
down—the serial interface protocol determines which
device is allowed to pull the SDATA line down at any given
time. The registers are 16bit wide, and can be accessed
through 16 or 8bit twowire serial interface sequences.
Protocol
The twowire serial interface defines several different
transmission codes, as follows:
a start bit
the slave device 8bit address
a(n) (no) acknowledge bit
an 8bit message
a stop bit
Sequence
A typical read or write sequence begins by the master
sending a start bit. After the start bit, the master sends the
slave device’s 8bit address. The last bit of the address
determines if the request is a read or a write, where a “0”
indicates a write and a “1” indicates a read. The slave device
acknowledges its address by sending an acknowledge bit
back to the master.
If the request was a write, the master then transfers the
8bit register address to which a write should take place. The
slave sends an acknowledge bit to indicate that the register
address has been received. The master then transfers the data
8 bits at a time, with the slave sending an acknowledge bit
after each 8 bits. The MT9V032 uses 16bit data for its
internal registers, thus requiring two 8bit transfers to write
to one register. After 16 bits are transferred, the register
address is automatically incremented, so that the next 16 bits
are written to the next register address. The master stops
writing by sending a start or stop bit.
A typical read sequence is executed as follows. First the
master sends the write mode slave address and 8bit register
address, just as in the write request. The master then sends
a start bit and the read mode slave address. The master then
clocks out the register data 8 bits at a time. The master sends
an acknowledge bit after each 8bit transfer. The register
address is autoincremented after every 16 bits is
transferred. The data transfer is stopped when the master
sends a noacknowledge bit. The MT9V032 allows for 8bit
data transfers through the twowire serial interface by
writing (or reading) the most significant 8 bits to the register
and then writing (or reading) the least significant 8 bits to
R0xF0 (240).
Bus Idle State
The bus is idle when both the data and clock lines are
HIGH. Control of the bus is initiated with a start bit, and the
bus is released with a stop bit. Only the master can generate
the start and stop bits.
Start Bit
The start bit is defined as a HIGHtoLOW transition of
the data line while the clock line is HIGH.
Stop Bit
The stop bit is defined as a LOWtoHIGH transition of
the data line while the clock line is HIGH.
Slave Address
The 8bit address of a twowire serial interface device
consists of 7 bits of address and 1 bit of direction. A “0” in
the LSB of the address indicates write mode, and a “1”
indicates read mode. As indicated above, the MT9V032
allows four possible slave addresses determined by the two
input pins, S_CTRL_ADR0 and S_CTRL_ADR1.
MT9V032
www.onsemi.com
13
Table 6. SLAVE ADDRESS MODES
{S_CTRL_ADR1, S_CTRL_ADR0} Slave Address Write/Read Mode
00 0x90 Write
0x91 Read
01 0x98 Write
0x99 Read
10 0xB0 Write
0xB1 Read
11 0xB8 Write
0xB9 Read
Data Bit Transfer
One data bit is transferred during each clock pulse. The
twowire serial interface clock pulse is provided by the
master. The data must be stable during the HIGH period of
the serial clock—it can only change when the twowire
serial interface clock is LOW. Data is transferred 8 bits at a
time, followed by an acknowledge bit.
Acknowledge Bit
The master generates the acknowledge clock pulse. The
transmitter (which is the master when writing, or the slave
when reading) releases the data line, and the receiver
indicates an acknowledge bit by pulling the data line LOW
during the acknowledge clock pulse.
NoAcknowledge Bit
The noacknowledge bit is generated when the data line
is not pulled down by the receiver during the acknowledge
clock pulse. A noacknowledge bit is used to terminate a
read sequence.
MT9V032
www.onsemi.com
14
TWOWIRE SERIAL INTERFACE SAMPLE READ AND WRITE SEQUENCES
16Bit Write Sequence
A typical write sequence for writing 16 bits to a register
is shown in Figure 9. A start bit given by the master, followed
by the write address, starts the sequence. The image sensor
then gives an acknowledge bit and expects the register
address to come first, followed by the 16bit data. After each
8bit word is sent, the image sensor gives an acknowledge
bit. All 16 bits must be written before the register is updated.
After 16 bits are transferred, the register address is
automatically incremented, so that the next 16 bits are
written to the next register. The master stops writing by
sending a start or stop bit.
Figure 9. Timing Diagram Showing a Write to R0x09 with Value 0x0284
SCLK
START ACK
0xB8 ADDR 0000 0010
R0x09
ACK ACK ACK
STOP
1000 0100
SDATA
16Bit Read Sequence
A typical read sequence is shown in Figure 10. First the
master has to write the register address, as in a write
sequence. Then a start bit and the read address specify that
a read is about to happen from the register. The master then
clocks out the register data 8 bits at a time. The master sends
an acknowledge bit after each 8bit transfer. The register
address is autoincremented after every 16 bits is
transferred. The data transfer is stopped when the master
sends a noacknowledge bit.
Figure 10. Timing Diagram Showing a Read from R0x09; Returned Value 0x0284
SCLK
START ACK
0xB8 ADDR 0xB9 ADDR 0000 0010
R0x09
ACK ACK ACK
STOP
1000 0100
NACK
SDATA
8Bit Write Sequence
To be able to write 1 byte at a time to the register, a special
register address is added. The 8bit write is done by first
writing the upper 8 bits to the desired register and then
writing the lower 8 bits to the special register address
(R0xF0). The register is not updated until all 16 bits have
been written. It is not possible to just update half of a register.
In Figure 11, a typical sequence for 8bit writing is shown.
The second byte is written to the special register (R0xF0).
Figure 11. Timing Diagram Showing a Bytewise Write to R0x09 with Value 0x0284
STOP
ACKSTART
0xB8 ADDR
ACK
SCLK
ACKACKACKACK
R0x09
0xB8 ADDR 0000 0010 1000 0100
START
SDATA R0xF0
8Bit Read Sequence
To read one byte at a time the same special register address
is used for the lower byte. The upper 8 bits are read from the
desired register. By following this with a read from the
special register (R0xF1) the lower 8 bits are accessed
(Figure 12). The master sets the noacknowledge bits
shown.
MT9V032
www.onsemi.com
15
Figure 12. Timing Diagram Showing a Bytewise Read from R0x09; Returned Value 0x0284
START
0xB9 ADDR
SCLK
STOP
ACKACKACK
R0x09
START
0xB8 ADDR 0000 0010
START
0xB9 ADDR
SCLK
NACKACKACKACKSTART
0xB8 ADDR 1000 0100
SDATA
SDATA
NACK
R0xF0
Register Lock
Included in the MT9V032 is a register lock (R0xFE)
feature that can be used as a solution to reduce the
probability of an inadvertent noisetriggered twowire
serial interface write to the sensor. All registers (or read
mode register—register 13 only) can be locked.
At powerup, the register lock defaults to a value of
0xBEEF, which implies that all registers are unlocked and
any twowire serial interface writes to the register get
committed.
Lock All Registers
If a unique pattern (0xDEAD) to R0xFE is programmed,
any subsequent twowire serial interface writes to registers
(except R0xFE) are NOT committed. Alternatively, if the
user writes a 0xBEEF to the register lock register, all
registers are unlocked and any subsequent twowire serial
interface writes to the register are committed.
Lock Read More Register Only (R0x0D)
If a unique pattern (0xDEAF) to R0xFE is programmed,
any subsequent twowire serial interface writes to register
13 are NOT committed. Alternatively, if the user writes a
0xBEEF to register lock register, register 13 is unlocked and
any subsequent twowire serial interface writes to this
register are committed.
MT9V032
www.onsemi.com
16
REGISTERS
CAUTION: Writing and changing the value of a
reserved register (word or bit) puts the
device in an unknown state and may
damage the device.
Table 7 provides default register descriptions of the
registers.
Table 8 provides detailed descriptions of the registers.
Table 7. DEFAULT REGISTER DESCRIPTIONS (1 = always 1;0 = always; d = programmable; ? = read only)
Register # (Hex) Description Data Format (Binary) Default Value (Hex)
0x00 Chip Version 0001 0011 0001 00001 (LSB) Iter. 1: 0x1311
Iter. 2: 0x1311
Iter. 3: 0x1313
0x01 Column Start 0000 00dd dddd dddd 0x0001
0x02 Row Start 0000 000d dddd dddd 0x0004
0x03 Window Height 0000 000d dddd dddd 0x01E0
0x04 Window Width 0000 00dd dddd dddd 0x02F0
0x05 Horizontal Blanking 0000 00dd dddd dddd 0x005E
0x06 Vertical Blanking 0ddd dddd dddd dddd 0x002D
0x07 Chip Control 0000 dddd dddd dddd 0x0388
0x08 Shutter Width 1 0ddd dddd dddd dddd 0x01BB
0x09 Shutter Width 2 0ddd dddd dddd dddd 0x01D9
0x0A Shutter Width Ctrl 0000 00dd dddd dddd 0x0164
0x0B Total Shutter Width 0ddd dddd dddd dddd 0x01E0
0x0C Reset 0000 0000 0000 00dd 0x0000
0x0D Read Mode 0000 0011 dddd dddd 0x0300
0x0E Monitor Mode 0000 0000 0000 000d 0x0000
0x0F Pixel Operation Mode 0000 0000 dddd dddd 0x0011
0x10 Reserved 0x0040
0x11 Reserved 0x8042
0x12 Reserved 0x0022
0x13 Reserved 0x2D32
0x14 Reserved 0x0E02
0x15 Reserved 0x7F32
0x16 Reserved 0x2802
0x17 Reserved 0x3E38
0x18 Reserved 0x3E38
0x19 Reserved 0x2802
0x1A Reserved 0x0428
0x1B LED_OUT Ctrl 0000 0000 0000 00dd 0x0000
0x1C ADC Mode Control 0000 0000 0000 00dd 0x0002
0x1D Reserved 0x0000
0x1E Reserved 0x0000
0x1F Reserved 0x0000
0x20 Reserved 0x01D1
0x21 Reserved 0x0020
0x22 Reserved 0x0020
0x23 Reserved 0x0010
MT9V032
www.onsemi.com
17
Table 7. DEFAULT REGISTER DESCRIPTIONS (continued)(1 = always 1;0 = always; d = programmable; ? = read only)
Register # (Hex) Default Value (Hex)Data Format (Binary)Description
0x24 Reserved 0x0010
0x25 Reserved 0x0020
0x26 Reserved 0x0010
0x27 Reserved 0x0010
0x28 Reserved 0x0010
0x29 Reserved 0x0010
0x2A Reserved 0x0020
0x2B Reserved 0x0004
0x2C VREF_ADC Control 0000 0000 0000 0ddd 0x0840
0x2D Reserved 0x0004
0x2E Reserved 0x0007
0x2F Reserved 0x0004
0x30 Reserved 0x0003
0x31 V1 0000 0000 000d dddd 0x001D
0x32 V2 0000 0000 000d dddd 0x0018
0x33 V3 0000 0000 000d dddd 0x0015
0x34 V4 0000 0000 000d dddd 0x0004
0x35 Analog Gain 0000 0000 0ddd dddd 0x0010
0x36 Max Analog Gain 0000 0000 0ddd dddd 0x0040
0x37 Reserved 0x0000
0x38 Reserved 0x0000
0x42 Frame Dark Average 0000 0000 ???? ???? RO
0x46 Dark Avg Thresholds dddd dddd dddd dddd 0x231D
0x47 BL Calib Control 1000 0000 ddd0 000d 0x8080
0x48 BL Calibration Value 0000 0000 dddd dddd 0x0000
0x4C BL Calib Step Size 0000 0000 000d dddd 0x0002
0x60 Reserved 0x0000
0x61 Reserved 0x0000
0x62 Reserved 0x0000
0x63 Reserved 0x0000
0x64 Reserved 0x0000
0x65 Reserved 0x0000
0x66 Reserved 0x0000
0x67 Reserved 0x0000
0x68 Reserved RO
0x69 Reserved RO
0x6A Reserved RO
0x6B Reserved RO
0x6C Reserved 0x0000
0x70 Row Noise Corr Ctrl 1 0000 d000 00d1 dddd 0x0034
0x71 Reserved 0x0000
0x72 Row Noise Constant 0000 0000 dddd dddd 0x002A
MT9V032
www.onsemi.com
18
Table 7. DEFAULT REGISTER DESCRIPTIONS (continued)(1 = always 1;0 = always; d = programmable; ? = read only)
Register # (Hex) Default Value (Hex)Data Format (Binary)Description
0x73 Row Noise Corr Ctrl 2 0000 00dd dddd dddd 0x02F7
0x74 Pixclk, FV, LV 0000 0000 000d dddd 0x0000
0x7F Digital Test Pattern 0ddd ddd dddd dddd 0x0000
0x80 Tile Weight/Gain X0_Y0 0000 0000 dddd dddd 0x00F4
0x81 Tile Weight/Gain X1_Y0 0000 0000 dddd dddd 0x00F4
0x82 Tile Weight/Gain X2_Y0 0000 0000 dddd dddd 0x00F4
0x83 Tile Weight/Gain X3_Y0 0000 0000 dddd dddd 0x00F4
0x84 Tile Weight/Gain X4_Y0 0000 0000 dddd dddd 0x00F4
0x85 Tile Weight/Gain X0_Y1 0000 0000 dddd dddd 0x00F4
0x86 Tile Weight/Gain X1_Y1 0000 0000 dddd dddd 0x00F4
0x87 Tile Weight/Gain X2_Y1 0000 0000 dddd dddd 0x00F4
0x88 Tile Weight/Gain X3_Y1 0000 0000 dddd dddd 0x00F4
0x89 Tile Weight/Gain X4_Y1 0000 0000 dddd dddd 0x00F4
0x8A Tile Weight/Gain X0_Y2 0000 0000 dddd dddd 0x00F4
0x8B Tile Weight/Gain X1_Y2 0000 0000 dddd dddd 0x00F4
0x8C Tile Weight/Gain X2_Y2 0000 0000 dddd dddd 0x00F4
0x8D Tile Weight/Gain X3_Y2 0000 0000 dddd dddd 0x00F4
0x8E Tile Weight/Gain X4_Y2 0000 0000 dddd dddd 0x00F4
0x8F Tile Weight/Gain X0_Y3 0000 0000 dddd dddd 0x00F4
0x90 Tile Weight/Gain X1_Y3 0000 0000 dddd dddd 0x00F4
0x91 Tile Weight/Gain X2_Y3 0000 0000 dddd dddd 0x00F4
0x92 Tile Weight/Gain X3_Y3 0000 0000 dddd dddd 0x00F4
0x93 Tile Weight/Gain X4_Y3 0000 0000 dddd dddd 0x00F4
0x94 Tile Weight/Gain X0_Y4 0000 0000 dddd dddd 0x00F4
0x95 Tile Weight/Gain X1_Y4 0000 0000 dddd dddd 0x00F4
0x96 Tile Weight/Gain X2_Y4 0000 0000 dddd dddd 0x00F4
0x97 Tile Weight/Gain X3_Y4 0000 0000 dddd dddd 0x00F4
0x98 Tile Weight/Gain X4_Y4 0000 0000 dddd dddd 0x00F4
0x99 Tile Coord. X 0/5 0000 00dd dddd dddd 0x0000
0x9A Tile Coord. X 1/5 0000 00dd dddd dddd 0x0096
0x9B Tile Coord. X 2/5 0000 00dd dddd dddd 0x012C
0x9C Tile Coord. X 3/5 0000 00dd dddd dddd 0x01C2
0x9D Tile Coord. X 4/5 0000 00dd dddd dddd 0x0258
0x9E Tile Coord. X 5/5 0000 00dd dddd dddd 0x02F0
0x9F Tile Coord. Y 0/5 0000 000d dddd dddd 0x0000
0xA0 Tile Coord. Y 1/5 0000 000d dddd dddd 0x0060
0xA1 Tile Coord. Y 2/5 0000 000d dddd dddd 0x00C0
0xA2 Tile Coord. Y 3/5 0000 000d dddd dddd 0x0120
0xA3 Tile Coord. Y 4/5 0000 000d dddd dddd 0x0180
0xA4 Tile Coord. Y 5/5 0000 000d dddd dddd 0x01E0
0XA5 AEC/AGC Desired Bin 0000 0000 00dd dddd 0x003A
0xA6 AEC Update Frequency 0000 0000 0000 dddd 0x0002
MT9V032
www.onsemi.com
19
Table 7. DEFAULT REGISTER DESCRIPTIONS (continued)(1 = always 1;0 = always; d = programmable; ? = read only)
Register # (Hex) Default Value (Hex)Data Format (Binary)Description
0xA7 Reserved 0x0000
0xA8 AEC LPF 0000 0000 0000 00dd 0x0000
0xA9 AGC Update Frequency 0000 0000 0000 dddd 0x0002
0xAA Reserved 0x0000
0xAB AGC LPF 0000 0000 0000 00dd 0x0002
0xAF AEC/AGC Enable 0000 0000 0000 00dd 0x0003
0xB0 AEC/AGC Pix Count dddd dddd dddd dddd 0xABE0
0xB1 LVDS Master Ctrl 0000 0000 0000 dddd 0x0002
0xB2 LVDS Shift Clk Ctrl 0000 0000 000d 0ddd 0x0010
0xB3 LVDS Data Ctrl 0000 0000 000d 0ddd 0x0010
0xB4 Data Stream Latency 0000 0000 0000 00dd 0x0000
0xB5 LVDS Internal Sync 0000 0000 0000 000d 0x0000
0xB6 LVDS Payload Control 0000 0000 0000 000d 0x0000
0xB7 Stereoscop. Error Ctrl 0000 0000 0000 0ddd 0x0000
0xB8 Stereoscop. Error Flag 0000 0000 0000 000? RO
0xB9 LVDS Data Output ???? ???? ???? ???? RO
0xBA AGC Gain Output 0000 0000 0??? ???? RO
0XBB AEC Gain Output ???? ???? ???? ???? RO
0xBC AGC/AEC Current Bin 0000 0000 00?? ???? RO
0xBD Maximum Shutter Width dddd dddd dddd dddd 0x01E0
0xBE AGC/AEC Bin Difference Threshold 0000 0000 dddd dddd 0x0014
0xBF Field Blank 0000 000d dddd dddd 0x0016
0xC0 Mon Mode Capture Ctrl 0000 0000 dddd dddd 0x000A
0xC1 Temperature 0000 00?? ???? ???? RO
0xC2 Analog Controls dddd dddd dddd dddd 0x0840
0xC3 NTSC FV & LV Ctrl 0000 0000 0000 00dd 0x03840
0xC4 NTSC Horiz Blank Ctrl dddd dddd dddd dddd 0x4416
0xC5 NTSC Vert Blank Ctrl dddd dddd dddd dddd 0x4421
0xF0 Bytewise Addr 0x0000
0xF1 Reserved Reserved
0xFE Register Lock dddd dddd dddd dddd 0xBEEF
0xFF Chip Version 0001 0011 0000 0000 Iter. 1: 0x1311
Iter. 2 : 0x1311
Iter. 3: 0x1313
MT9V032
www.onsemi.com
20
Shadowed Registers
Some sensor settings cannot be changed during frame
readout. For example, changing the register Window Width
(R0x04) part way through frame readout results in
inconsistent LINE_VALID behavior. To avoid this, the
MT9V032 double buffers many registers by implementing
a “pending” and a “live” version. Twowire serial interface
reads and writes access the pending register. The live
register controls the sensor operation. The value in the
pending register is transferred to a live register at a fixed
point in the frame timing, called “framestart.” Framestart
is defined as the point at which the first dark row is read out.
By default, this occurs four row times before
FRAME_VALID goes HIGH. To determine which registers
or register fields are doublebuffered in this way, see the
“Shadowed” column in Table 8.
Shadowed
N = No. The register value is updated and used
immediately.
Y = Yes. The register value is updated at next frame
start. Frame start is defined as when the first dark row
is read out. By default this is four rows before
FRAME_VALID goes HIGH.
Read/Write
R = Readonly register/bit.
W = Read/Write register/bit.
Table 8 provides a detailed description of the registers. Bit
fields that are not identified in the table are read only.
Table 8. REGISTER DESCRIPTIONS
Bit Bit Name Bit Description
Default
in Hex
(Dec)
Shad-
owed
Legal
Values
(Dec)
Read/
Write
0X00/0XFF (0/255) CHIP VERSION
15:0 Chip Version Chip version—readonly Iter. 1:
0x1311
(4881)
Iter. 2:
0x1311
(4881)
Iter. 3:
0x1313
(4883)
R
0X01 (1) COLUMN START
9:0 Column Start The first column to be read out (not counting dark
columns that may be read). To window the image down, set
this register to the starting X value. Readable/active col-
umns are 1–752.
1 Y 1–752 W
0X02 (2) ROW START
8:0 Row Start The first row to be read out (not counting any dark rows that
may be read). To window the image down, set this register
to the starting Y value. Setting a value less than four is not
recommended since the dark rows should be read using
R0x0D.
4 Y 4–482 W
0X03 (3) WINDOW HEIGHT
8:0 Window Height Number of rows in the image to be read out (not counting
any dark rows or border rows that may be read).
1E0
(480)
Y 1–480 W
0X04 (4) WINDOW WIDTH
9:0 Window Width Number of columns in image to be read out (not counting
any dark columns or border columns that may be read).
2F0
(752)
Y 1–752 W
0X05 (5) HORIZONTAL BLANKING
9:0 Horizontal Blanking Number of blank columns in a row. Minimum horizontal
blanking is 43 columns.
05E
(94)
Y 43–1023 W
0X06 (6) VERTICAL BLANKING
14:0 Vertical Blanking Number of blank rows in a frame. This number must be
equal to or larger than four.
002D
(45)
Y 4–3000 W
0X07 (7) CHIP CONTROL
MT9V032
www.onsemi.com
21
Table 8. REGISTER DESCRIPTIONS
0X06 (6) VERTICAL BLANKING
2:0 Scan Mode 0 = Progressive scan.
1 = Not valid.
2 = Twofield Interlaced scan. Evennumbered rows are
read first, and followed by oddnumbered rows.
3 = Singlefield Interlaced scan. If start address is even
number, only evennumbered rows are read out; if start
address is odd number, only oddnumbered rows are
read out. Effective image size is decreased by half.
0 Y 0, 2, 3 W
3Sensor Master/Slave
Mode
0 = Slave mode. Initiating exposure and readout is allowed.
1 = Master mode. Sensor generates its own exp
sure and readout timing according to simultaneous/se-
quential mode control bit.
1 Y 0,1 W
4Sensor Snapshot Mode 0 = Snapshot disabled.
1 = Snapshot mode enabled. The start of frame is triggered
by providing a pulse at EXPOSURE pin. Sensor master/
slave mode should be set to logic 1 to turn on this mode.
0 Y 0,1 W
5Stereoscopy Mode 0 = Stereoscopy disabled. Sensor is standalone and the
PLL generates a 320 MHz (x12) clock.
1 = Stereoscopy enabled. The PLL generates a 480 MHz
(x18) clock.
0 Y 0,1 W
6Stereoscopic
Master/Slave mode
0 = Stereoscopic master.
1 = Stereoscopic slave. Stereoscopy mode should be en-
abled when using this bit.
0 Y 0,1 W
7Parallel Output Enable 0 = Disable parallel output. DOUT(9:0) are in HighZ.
1 = Enable parallel output.
1 Y 0,1 W
8Simultaneous/
Sequential Mode
0 = Sequential mode. Pixel and column readout takes place
only after exposure is complete.
1 = Simultaneous mode. Pixel and column readout takes
place in conjunction with exposure.
1 Y 0,1 W
0X08 (8) SHUTTER WIDTH 1
14:0 Shutter Width 1 The row number in which the first knee occurs. This may be
used only when high dynamic range option (bit 6 of R0x0F)
is enabled and exposure knee point auto adjust control bit is
disabled. This register is not shadowed, but any change
made does not take effect until the following new frame.
1BB
(443)
N 1–32767 W
0X09 (9) SHUTTER WIDTH 2
14:0 Shutter Width 2 The row number in which the second knee occurs. This may
be used only when high dynamic range option (bit 6 of
R0x0F) is enabled and exposure knee point auto adjust
control bit is disabled. This register is not shadowed, but
any change made does not take effect until the following
new frame.
Shutter width 2 = (bits 14:0)
Note:
t1 = Shutter width 1;
t2 = Shutter width 2 – Shutter 1;
t3 = Total integration – Shutter width 2.
1D9
(473)
N 1–32767 W
0X0A (10) SHUTTER WIDTH CONTROL
3:0 T2 Ratio Onehalf to the power of this value indicates the ratio of
duration time t2, when saturation control gate is adjusted to
level V2 to total integration when exposure knee point auto
adjust control bit is enabled. This register is not shadowed,
but any change made does not take effect until the following
new frame.
t2 = Total integration × (½)t2_ratio.
4 N 0–15 W
MT9V032
www.onsemi.com
22
Table 8. REGISTER DESCRIPTIONS
0X09 (9) SHUTTER WIDTH 2
7:4 T3 Ratio Onehalf to the power of this value indicates the ratio of
duration time t3, when saturation control gate is adjusted to
level V3 to total integration when exposure knee point auto
adjust control bit is enabled. This register is not shadowed,
but any change made does not take effect until the following
new frame.
t3 = Total integration × (½)t3_ratio.
Note: t1 = Total integration t2 t3.
6 N 0–15 W
8Exposure Knee Point
Auto Adjust Enable
0 = Auto adjust disabled.
1 = Auto adjust enabled.
1 N 0,1 W
9Single Knee Enable 0 = Single knee disabled.
1 = Single knee enabled.
0 N 0,1 W
0X0B (11) TOTAL SHUTTER WIDTH
14:0 Total Shutter Width Total integration time in number of rows. This value is used
only when AEC is disabled only (bit 0 of Register 175). This
register is not shadowed, but any change made does not
take effect until the following new frame.
1E0
(480)
N 1–32767 W
0X0C (12) RESET
0Soft Reset Setting this bit causes the sensor to abandon the current
frame by resetting all digital logic except twowire serial
interface configuration. This is a selfresetting register bit
and should always read “0.” (This bit deasserts internal
active LOW reset signal for 15 clock cycles.)
0 N 0, 1 W
1Auto Block Soft Reset Setting this bit causes the sensor to reset the automatic
gain and exposure control logic. This is a selfresetting
register bit and should always read “0.” (This bit deasserts
internal active LOW reset signal for 15 clock cycles.)
0 Y 0, 1 W
0X0D (13) READ MODE
1:0 Row Bin 0 = Normal operation.
1 = Row bin 2. Two pixel rows are read per row output.
Image size is effectively reduced by a factor of 2 vertically
while data rate and pixel clock are not affected. Resulting
frame rate is increased by 2.
2 = Row bin 4. Four pixel rows are read per row output.
Image size is effectively reduced by a factor of 4 vertically
while data rate and pixel clock are not affected. Resulting
frame rate is increased by 4.
3 = Not valid.
0 Y 0, 1, 2 W
3:2 Column Bin 0 = Normal operation.
1 = Column bin 2. When set, image size is reduced by a
factor of 2 horizontally. Frame rate is not affected but data
rate and pixel clock are reduced by onehalf that of
master clock.
2 = Column bin 4. When set, image size is reduced by a
factor of 4 horizontally. Frame rate is not affected but data
rate and pixel clock are reduced by onefourth that of
master clock.
3 = Not valid.
0 Y 0, 1, 2 W
4Row Flip Read out rows from bottom to top (upside down). When set,
row readout starts from row (Row Start + Window Height)
and continues down to (Row Start + 1). When clear, readout
starts at Row Start and continues to (Row Start + Window
Height 1). This ensures that the starting color is main-
tained.
0 Y 0, 1 W
MT9V032
www.onsemi.com
23
Table 8. REGISTER DESCRIPTIONS
0X09 (9) SHUTTER WIDTH 2
5Column Flip Read out columns from right to left (mirrored). When set,
column readout starts from column (Col Start + Window
Width) and continues down to (Col Start + 1). When clear,
readout starts at Col Start and continues to (Col Start +
Window Width 1). This ensures that the starting color is
maintained.
0 Y 0, 1 W
6Show Dark Rows When set, the programmed dark rows is output before the
active window. Frame valid is thus asserted earlier than
normal. This has no effect on integration time or frame rate.
Whether the dark rows are shown in the image or not the
definition frame start is before the dark rows are read out.
0 Y 0, 1 W
7Show Dark Columns When set, the programmed dark columns are output before
the active pixels in a line. Line valid is thus asserted earlier
than normal, and the horizontal blank time gets shorter by
18 pixel clocks.
0 Y 0, 1 W
9:8 Reserved Reserved. 3
0X0E (14) MONITOR MODE
0Monitor Mode Enable Setting this bit puts the sensor into a cycle of sleeping for
five minutes, and waking up to capture a programmable
number of frames (R0xC0). Clearing this bit resumes nor-
mal operation.
0 Y 0, 1 W
0X0F (15) PIXEL OPERATION MODE
2Color/Mono Should be set according to sensor type:
0 = Monochrome.
1 = Color.
0 Y 0, 1 W
6High Dynamic Range 0 = Linear operation.
1 = High Dynamic Range. Voltage and shutter width must
be correctly set for saturation control to operate.
0 Y 0, 1 W
0X1B (27) LED_OUT CONTROL
0Disable LED_OUT Disable LED_OUT output. When cleared, the output pin
LED_OUT is pulsed high when the sensor is undergoing
exposure.
0 Y 0, 1 W
1Invert LED_OUT Invert polarity of LED_OUT output. When set, the output pin
LED_OUT is pulsed low when the sensor is undergoing
exposure.
0 Y 0, 1 W
0X1C (28) ADC RESOLUTION CONTROL
1:0 ADC Mode 0 = Invalid.
1 = Invalid.
2 = 10bit linear.
3 = 12to10bit companding.
2 Y 2, 3 W
0X2C (44) VREF_ADC CONTROL
2:0 VREF_ADC Voltage
Level
0 = VREF_ADC = 1.0V.
1 = VREF_ADC = 1.1V.
2 = VREF_ADC = 1.2V.
3 = VREF_ADC = 1.3V.
4 = VREF_ADC = 1.4V.
5 = VREF_ADC = 1.5V.
6 = VREF_ADC = 1.6V.
7 = VREF_ADC = 2.1V.
Range: 1.0–2.1V; Default: 1.4V
VREF_ADC for ADC.
4 N 0–7 W
0X31 (49) V1 CONTROL
4:0 V1 voltage level V_Step = bits (4:0) x 62.5mV + 0.5625V.
Range: 0.5625 2.5V; Default: 2.375V.
Usage: V_Step1 HiDy voltage.
1D
(29)
N 0–31 W
0X32 (50) V2 CONTROL
MT9V032
www.onsemi.com
24
Table 8. REGISTER DESCRIPTIONS
0X32 (50) V2 CONTROL
4:0 V2 voltage level V_Step = bits (4:0) x 62.5mV + 0.5625V.
Range: 0.5625 2.5V; Default: 2.0625V.
Usage: V_Step2 HiDy voltage.
18
(24)
N 0–31 W
0X33 (51) V3 CONTROL
4:0 V3 voltage level V_Step = bits (4:0) x 62.5mV + 0.5625V.
Range: 0.5625 2.5V; Default: 1.875V.
Usage: V_Step3 HiDy voltage.
15
(21)
N 0–31 W
0X34 (52) V4 CONTROL
4:0 V4 voltage level V_Step = bits (4:0) x 62.5mV + 0.5625V.
Range: 0.5625 2.5V; Default: 0.8125V.
Usage: V_Step HiDy parking voltage, also provides anti
blooming when V_Step is disabled.
4 N 0–31 W
0X35 (53) ANALOG GAIN
6:0 Analog Gain Analog gain = bits (6:0) x 0.0625 for values 16–31
Analog gain = bits (6:0)/2 x 0.125 for values 32–64
For values 16–31: each LSB increases analog gain
0.0625v/v. A value of 16 = 1X gain. Range: 1X to 1.9375X
For values 32–64: each 2 LSB increases analog gain
0.125v/v. Range: 2X to 4X. An LSB increase of 1 will not
increase the gain; the value must be incremented by 2
No exception detection is installed and caution
should be taken when programming
10
(16)
Y 16–64 W
0X36 (54) MAXIMUM ANALOG GAIN
6:0 Maximum Analog Gain This register is used by the automatic gain control (AGC) as
the upper threshold of gain. This ensures the new calibrated
gain value does not exceed that which the MT9V032 sup-
ports.
Range: 16dec–64dec for 1X–4X respectively. Note: No ex-
ception detection is installed; caution should be taken when
programming.
40
(64)
Y 16–64 W
0X42 (66) FRAME DARK AVERAGE
7:0 Frame Dark Average The value read is the frame averaged black level, that is,
used in the black level algorithm calculations.
0 R
0X46 (70) DARK AVERAGE THRESHOLDS
7:0 Lower threshold Lower threshold for targeted black level in ADC LSBs. 1D
(29)
N 0–255 W
15:8 Upper threshold Upper threshold for targeted black level in ADC LSBs. 23
(35)
N 0–255 W
0X47 (71) BLACK LEVEL CALIBRATION CONTROL
0Manual Override Manual override of black level correction.
1 = Override automatic black level correction with pro-
grammed values. (R0x48).
0 = Normal operation (default).
0 N 0, 1 W
7:5 Frames to average over Two to the power of this value decide how many frames to
average over when the black level algorithm is in the aver-
aging mode. In this mode the running frame average is
calculated from the following formula:
Running frame ave = Old running frame ave (old running
frame ave)/2n + (new frame ave)/ 2n.
4 N 0–7 W
15:8 Reserved Reserved. 80
(128)
0X48 (72) BLACK LEVEL CALIBRATION VALUE
MT9V032
www.onsemi.com
25
Table 8. REGISTER DESCRIPTIONS
0X48 (72) BLACK LEVEL CALIBRATION VALUE
7:0 Black Level Calibration
Value
Analog calibration offset: Negative numbers are represented
with two’s complement, which is shown in the following
formula: Sign = bit 7 (0 is positive, 1 is negative).
If positive offset value: Magnitude = bit 6:0.
If negative offset value: Magnitude = not (bit 6:0) + 1.
During twowire serial interface read, this register returns
the userprogrammed value when manual override is en-
abled (R0x47 bit 0); otherwise, this register returns the re-
sult
obtained from the calibration algorithm.
0 N –127 to
127
W
0X4C (76) BLACK LEVEL CALIBRATION VALUE STEP SIZE
4:0 Step Size of Calibration
Value
This is the size calibration value may change (positively or
negatively) from frame to frame.
1 calib LSB = ½ ADC LSB, assuming analog gain = 1.
2 N 0–31 W
0X70 (112) ROW NOISE CORRECTION CONTROL 1
3:0 Number of Dark Pixels The number of pixels used in the rowwise noise calcula-
tion.
0 = 2 pixels.
1 = 4 pixels.
2 = 6 pixels.
4 = 10 pixels.
8 = 18 pixels.
See “Rowwise Noise Correction” for additional information.
4 Y 0, 1, 2,
4, 8
W
4Reserved Reserved. 1
5Enable noise correction 0 = Normal operation.
1 = Enable row noise cancellation algorithm. When this bit is
set, on a per row basis, the dark average is subtracted
from each pixel in the row, and then a constant (R0x72) is
added.
1 Y 0, 1 W
11 Use black level average 1 = Use black level frame average from the dark rows in the
row noise correction algorithm for low gains. This frame
average was taken before the last adjustment of the offset
DAC for that frame, so it might be slightly off.
0 = Use the average value of the dark columns read out in
each row as dark average.
0 Y 0, 1 W
0X72 (114) ROW NOISE CONSTANT
7:0 Row noise constant Constant used in the row noise cancellation algorithm. It
should be set to the dark level targeted by the black level
algorithm plus the noise expected between the averaged
values of dark columns. At default the constant is set to 42
LSB.
2A
(42)
Y 0–255 W
0X73 (115) ROW NOISE CORRECTION CONTROL 2
9:0 Dark start column ad-
dress
The starting column address for the dark columns to be
used in the rowwise noise correction algorithm.
2F7
(759)
Y 759–775 W
0X74 (116) PIXEL CLOCK, FRAME AND LINE VALID CONTROL
0Invert Line Valid Invert line valid. When set, LINE_VALID is reset to logic “0”
when DOUT is valid.
0 Y 0, 1 W
1Invert Frame Valid Invert frame valid. When set, FRAME_VALID is reset to
logic “0” when frame is valid.
0 Y 0, 1 W
2XOR Line Valid 1 = Line valid = ”Continuous” Line Valid XOR Frame Valid
0 = Line Valid determined by bit 3. Ineffective if Continuous
Line Valid is set.
0 Y 0, 1 W
3Continuous Line Valid 1 = ”Continuous” Line Valid (continue producing line valid
during vertical blank).
0 = Normal Line Valid (default, no line valid during vertical
blank).
0 Y 0, 1 W
MT9V032
www.onsemi.com
26
Table 8. REGISTER DESCRIPTIONS
0X74 (116) PIXEL CLOCK, FRAME AND LINE VALID CONTROL
4Invert Pixel Clock Invert pixel clock. When set, LINE_VALID, FRAME_VALID,
and DOUT is set up to the rising edge of pixel clock, PIXCLK.
When clear, they are set up to the falling edge of PIXCLK.
0 Y 0, 1 W
0X7F (127) DIGITAL TEST PATTERN
9:0 Twowire Serial Inter-
face Test Data
The 10bit test data in this register is used in place of the
data from the sensor. The data is inserted at the beginning
of the digital signal processing. Both test enable (bit 13) and
use twowire serial interface (bit 10) must be set.
0 N 0–1023 W
10 Use Twowire Serial In-
terface Test Data
0 = Use Gray Shade Test Pattern as test data.
1 = Use Twowire Serial Interface Test Data (bits 9:0) as
test data.
0 N 0, 1 W
12:11 Gray Shade Test Pat-
tern
0 = None.
1 = Vertical Shades.
2 = Horizontal Shades.
3 = Diagonal Shade.
When bits (12:11) ! 0, the MT9V032 generates a gray
shaded test pattern to be used as digital test data. Ineffec-
tive when Use Twowire Serial Interface Test Data (bit 10)
is set.
0 N 0–3 W
13 Test Enable Enable the use of test data/gray shaded test pattern in the
signal chain. The data is inserted instead of data from the
ADCs.
Set R0x70 bit 5 = 0 when using this mode. If R0x70 bit 5 =
1, the rowwise correction algorithm processes the test data
values and the result is not accurate.
0 Y 0, 1 W
14 Flip TwoWire Serial In-
terface Test Data
Use only when twowire serial interface test data (bit 10) is
set. When set, the twowire serial interface test data (bits
9:0) is used in place of the data from ADC/memory on odd
columns, while complement of the twowire serial interface
test data is used on even columns.
0 N 0, 1 W
0X80 (128) 0X98 (152) TILED DIGITAL GAIN
3:0 Tile Gain Tile Digital Gain = Bits (3:0) x 0.25. See “Gain Settings” for
additional information on digital gain.
4 Y 1–15 W
7:4 Sample Weight To indicate the weight of individual tile used in the automatic
gain/exposure control algorithm.
F
(15)
Y 0–15 W
Refer to Figure 25 for R0x99 (153) R0xA4 (164).
0X99 (153) DIGITAL TILE COORDINATE 1 XDIRECTION
9:0 X 0/5 The starting xcoordinate of digital tiles X0_*. 0 Y 0–752 W
0X9A (154) DIGITAL TILE COORDINATE 2 XDIRECTION
9:0 X 1/5 The starting xcoordinate of digital tiles X1_*. 096
(150)
Y 0–752 W
0X9B (155) DIGITAL TILE COORDINATE 3 XDIRECTION
9:0 X 2/5 The starting xcoordinate of digital tiles X2_*. 12C
(300)
Y 0–752 W
0X9C (156) DIGITAL TILE COORDINATE 4 XDIRECTION
9:0 X 3/5 The starting xcoordinate of digital tiles X3_*. 1C2
(450)
Y 0–752 W
0X9D (157) DIGITAL TILE COORDINATE 5 XDIRECTION
9:0 X 4/5 The starting xcoordinate of digital tiles X4_*. 258
(600)
Y 0–752 W
0X9E (158) DIGITAL TILE COORDINATE 6 XDIRECTION
9:0 X 5/5 The ending xcoordinate of digital tiles X4_*. 2F0
(752)
Y 0–752 W
MT9V032
www.onsemi.com
27
Table 8. REGISTER DESCRIPTIONS
0X9F (159) DIGITAL TILE COORDINATE 1 YDIRECTION
8:0 Y 0/5 The starting ycoordinate of digital tiles *_Y0. 0 Y 0–480 W
0XA0 (160) DIGITAL TILE COORDINATE 2 YDIRECTION
8:0 Y 1/5 The starting ycoordinate of digital tiles *_Y1. 60
(96)
Y 0–480 W
0XA1 (161) DIGITAL TILE COORDINATE 3 YDIRECTION
8:0 Y 2/5 The starting ycoordinate of digital tiles *_Y2. 0C0
(192)
Y 0–480 W
0XA2 (162) DIGITAL TILE COORDINATE 4 YDIRECTION
8:0 Y 3/5 The starting ycoordinate of digital tiles *_Y3. 120
(288)
Y 0–480 W
0XA3 (163) DIGITAL TILE COORDINATE 5 YDIRECTION
8:0 Y 4/5 The starting ycoordinate of digital tiles *_Y4. 180
(384)
Y 0–480 W
0XA4 (164) DIGITAL TILE COORDINATE 6 YDIRECTION
8:0 Y 5/5 The ending ycoordinate of digital tiles *_Y4. 1E0
(480)
Y 0–480 W
0XA5 (165) AEC/AGC DESIRED BIN
5:0 Desired Bin Userdefined “desired bin” that gives a measure of how
bright the image is intended
3A
(58)
Y 1–64 W
0XA6 (166) AEC UPDATE FREQUENCY
3:0 Exp Skip Frame The number of frames that the AEC must skip before updat-
ing the exposure register (R0xBB).
2 Y 0–15 W
0XA8 (168) AEC LOW PASS FILTER
1:0 Exp LPF This value plays a role in determining the increment/decre-
ment size of exposure value from frame to frame. If current
bin ! 0 (R0xBC),
When Exp LPF = 0:
Actual new exposure = Calculated new exposure
When Exp LPF = 1:
If |(Calculated new exp current exp) | > (current exp/4),
Actual new exposure = Calculated new exposure, otherwise
Actual new exposure = Current exp + (calculated new
exp/2)
When Exp LPF = 2:
If |(Calculated new exp current exp) |> (current exp/4),
Actual new exposure = Calculated new exposure, otherwise
Actual new exposure = Current exp + (calculated new
exp/4)
2 Y 0–2 WX
0XA9 (169) AGC OUTPUT UPDATE FREQUENCY
3:0 Gain Skip Frame The number of frames that the AGC must skip before updat-
ing the gain register (R0xBA).
2 Y 0–15 W
0XAB (171) AGC LOW PASS FILTER
MT9V032
www.onsemi.com
28
Table 8. REGISTER DESCRIPTIONS
0XAB (171) AGC LOW PASS FILTER
1:0 Gain LPF This value plays a role in determining the increment/decre-
ment size of gain value from frame to frame. If current bin !
0 (R0xBC)
When Gain LPF = 0
Actual new gain = Calculated new gain
When Exp LPF = 1
if |(Calculated new gain current gain) | > (current gain/4),
Actual new gain = Calculated new gain, otherwise
Actual new gain = Current exp+ (calculated new gain/2)
When Exp LPF = 2:
if |(Calculated new gain current gain) | > (current gain /4),
Actual new gain = Calculated new gain, otherwise
Actual new gain = Current gain+ (calculated new gain/4).
2 Y 0–2 W
0XAF (175) AGC/AEC ENABLE
0AEC Enable 0 = Disable Automatic Exposure Control
1 = Enable Automatic Exposure Control
1Y0, 1 W
1AGC Enable 0 = Disable Automatic Gain Control.
1 = Enable Automatic Gain Control.
1Y0, 1 W
0XB0 (176) AGC/AEC PIXEL COUNT
150Pixel Count The number of pixel used for the AEC/AGC histogram. ABE0
(44,00)
Y 0–65535 W
0XB1 (177) LVDS MASTER CONTROL
0PLL Bypass 0 = Internal shiftCLK is driven by PLL.
1 = Internal shiftCLK is sourced from the LVDS_BY-
PASS_CLK.
0 Y 0, 1 W
1LVDS Powerdown 0 = Normal operation.
1 = Powerdown LVDS block.
1 Y 0, 1 W
2PLL Test Mode 0 = Normal operation.
1 = The PLL output frequency is equal to the system clock
frequency (26.6 MHz).
0 Y 0, 1 W
3LVDS Test Mode 0 = Normal operation.
1 = The SER_DATAOUT_P drives a square wave in both
stereo and standalone modes). In stereo mode, ensure
that SER_DATAIN_P is logic “0.”
0 Y 0, 1 W
0XB2 (178) LVDS SHIFT CLOCK CONTROL
2:0 Shiftclk Delay Element
Select
The amount of shiftCLK delay that minimizes intersensor
skew.
0 Y 0–7 W
4LVDS Receiver Power
down
When set, LVDS receiver is disabled. 1 Y 0, 1 W
0XB3 (179) LVDS DATA CONTROL
2:0 Data Delay Element
Select
The amount of data delay that minimizes intersensor skew. 0 Y 0–7 W
4LVDS Driver Power
down
When set, data LVDS driver is disabled. 1 Y 0, 1 W
0XB4 (180) LVDS LATENCY
1:0 Stream Latency Select The amount of delay so that the two streams are in sync. 0 Y 0–3 W
0XB5 (181) LVDS INTERNAL SYNC
0LVDS Internal Sync En-
able
When set, the MT9V032 generates sync pattern (data with
all zeros except start bit) on LVDS_SER_DATA_OUT.
0 Y 0, 1 W
0XB6 (182) LVDS PAYLOAD CONTROL
MT9V032
www.onsemi.com
29
Table 8. REGISTER DESCRIPTIONS
0XB6 (182) LVDS PAYLOAD CONTROL
0Use 10bit Pixel Enable When set, all 10 pixel data bits are output in standalone
mode. Control signals are embedded. If clear, 8 bits of pixel
data are output with 2 control bits. See “LVDS Output For-
mat” for additional information.
0 Y 0, 1 W
0XB7 (183) STEREOSCOPY ERROR CONTROL
0Enable Stereo Error
Detect
Set this bit to enable stereo error detect mechanism. 0 Y 0, 1 W
1Enable Stick Stereo Er-
ror Flag
When set, the stereo error flag remains asserted once an
error is detected unless clear stereo error flag (bit 2) is set.
0 Y 0, 1 W
2Clear Stereo Error Flag Set this bit to clear the stereoscopy error flag (R0xB8
returns to logic 0).
0 Y 0, 1 W
0XB8 (184) STEREOSCOPY ERROR FLAG
0Stereoscopy Error Flag Stereoscopy error status flag. It is also directly connected to
the ERROR output pin.
R
0XB9 (185) LVDS DATA OUTPUT
15:0 Combo Reg This 16bit value contains both 8bit pixel values from both
stereoscopic master and slave sensors. It can be used in
diagnosis to determine how well in sync the two sensors
are. Captures the state when master sensor has issued
a reserved byte and slave has not.
Note: This register should be read from the stereoscopic
master sensor only.
R
0XBA (186) AGC GAIN OUTPUT
6:0 AGC Gain Status register to report the current gain value obtained
from the AGC algorithm.
10
(16)
R
0XBB (187) AEC EXPOSURE OUTPUT
15:0 AEC Exposure Status register to report the current exposure value obtained
from the AEC Algorithm.
00C8
(200)
R
0XBC (188) AGC/AEC CURRENT BIN
5:0 Current Bin Status register to report the current bin of the histogram. R
0XBD (189) MAXIMUM TOTAL SHUTTER WIDTH
15:0 Maximum Total Shutter
Width
This register is used by the automatic exposure control
(AEC) as the upper threshold of exposure. This ensures the
new calibrated integration value does not exceed that which
the MT9V032 supports.
01E0
(480)
Y 1–2047 W
0XBE (190) AGC/AEC BIN DIFFERENCE THRESHOLD
7:0 Bin Difference Thresh-
old
This register is used by the AEC only when exposure reach-
es its minimum value of 1. If the difference between desired
bin (R0xA5) and current bin (R0xBC) is larger than the
threshold, the exposure is increased.
14
(20)
Y 0–63 W
0XBF (191) FIELD VERTICAL BLANK
8:0 Field Vertical Blank The number of blank rows between odd and even fields.
Note: For interlaced (both field) mode only. See R0x07[2:0].
16
(22)
Y 0–255 W
0XC0 (192) MONITOR MODE CAPTURE CONTROL
7:0 Image Capture Numb The number of frames to be captured during the wakeup
period when monitor mode is enabled.
0A
(10)
Y 0–255 W
0XC1 (193) THERMAL INFORMATION
9:0 Temperature Output Status register to report the temperature of sensor. Updated
once per frame.
R
0XC2 (194) ANALOG CONTROLS
6Reserved Reserved. 1 N 0, 1 W
MT9V032
www.onsemi.com
30
Table 8. REGISTER DESCRIPTIONS
0XC2 (194) ANALOG CONTROLS
7AntiEclipse Enable Setting this bit turns on antieclipse circuitry. 0 N 0, 1 W
11:13 V_rst_lim voltage Level V_rst_lim = bits (2:0) × 50mV + 1.95V
Range: 1.95–2.30V; Default: 2.00V
Usage: For antieclipse reference voltage control
1 N 0–7 W
0XC3 (195) NTSC FRAME VALID CONTROL
0Extend Frame Valid When set, frame valid is extended for halfline in length at
the odd field.
0 Y 0, 1 W
1Replace FV/LV with
Ped/Snyc
When set, frame valid and line valid is replaced by ped and
sync signals respectively.
0 Y 0, 1 W
0XC4 (196) NTSC HORIZONTAL BLANKING CONTROL
7:0 Front porch width The front porch width in number of master clock cycle.
NTSC standard is 1.5msec ±0.1msec
16
(22)
Y 0–255 W
15:8 Sync Width The sync pulse width in number of master clock cycle.
NTSC standard is 4.7msec ±0.1msec.
044
(68)
Y 0–255 W
0XC5 (197) NTSC VERTICAL BLANKING CONTROL
7:0 Equalizing Pulse Width The pulse width in number of master clock cycle. NTSC
standard is 2.3msec ±0.1msec.
21
(33)
Y 0–255 W
15:8 Vertical Serration Width The pulse width in number of master clock cycle. NTSC
standard is 4.7msec ±0.1msec.
44
(68)
Y 0–255 W
0XF0 (240) BYTEWISE ADDRESS
Bytewise Address Special address to perform 8bit READs and WRITEs to
the sensor. See the “TwoWire Serial Interface Sam-
ple Read and Write Sequences” for further details on how to
use this functionality.
0XFE (254) REGISTER LOCK
15:0 Register Lock Code To lock all registers except R0xFE, program data with
0xDEAD; to unlock twowire serial interface, program data
with 0xBEEF. When twowire serial interface is locked, any
subsequent twowire serial interface write to register other
than to twowire serial interface Protect Enable Register is
ignored until twowire serial interface is unlocked.
To lock Register 13 only, program data with 0xDEAF; to
unlock, program data with 0xBEEF. When Register 13 is
locked, any subsequent twowire serial interface write to
this register only is ignored until register is unlocked.
BEEF
(48879)
N 48879,
57005,
57007
W
MT9V032
www.onsemi.com
31
FEATURE DESCRIPTION
Operational Modes
The MT9V032 works in master, snapshot, or slave mode.
In master mode the sensor generates the readout timing. In
snapshot mode it accepts an external trigger to start
integration, then generates the readout timing. In slave mode
the sensor accepts both external integration and readout
controls. The integration time is programmed through the
twowire serial interface during master or snapshot modes,
or controlled through externally generated control signal
during slave mode.
Master Mode
There are two possible operation methods for master
mode: simultaneous and sequential. One of these operation
modes must be selected through the twowire serial
interface.
Simultaneous Master Mode
In simultaneous master mode, the exposure period occurs
during readout. The frame synchronization waveforms are
shown in Figure13 and Figure 14. The exposure and readout
happen in parallel rather than sequentially, making this the
fastest mode of operation.
Figure 13. Simultaneous Master Mode Synchronization Waveforms #1
Readout Time > Exposure Time
Readout Time
LED_OUT
FRAME_VALID
XXX
Vertical Blanking
XXX XXX
LINE_VALID
DOUT(9:0)
LED_OUT
FRAME_VALID
XXX XXX XXX
LINE_VALID
DOUT(9:0
)
Vertical Blanking
Exposure Time
Exposure Time > Readout Time
Figure 14. Simultaneous Master Mode Synchronization Waveforms #2
DOUT(9:0)
When exposure time is greater than the sum of vertical
blank and window height, the number of vertical blank rows
is increased automatically to accommodate the exposure
time.
Sequential Master Mode
In sequential master mode the exposure period is followed
by readout. The frame synchronization waveforms for
sequential master mode are shown in Figure15. The frame
rate changes as the integration time changes.
MT9V032
www.onsemi.com
32
Figure 15. Sequential Master Mode Synchronization Waveforms
XXX XXX XXX
Exposure Time
LED_OUT
FRAME_VALID
LINE_VALID
DOUT(9:0)
Snapshot Mode
In snapshot mode the sensor accepts an input trigger
signal which initiates exposure, and is immediately
followed by readout. Figure 16 shows the interface signals
used in snapshot mode. In snapshot mode, the start of the
integration period is determined by the externally applied
EXPOSURE pulse that is input to the MT9V032. The
integration time is preprogrammed via the twowire serial
interface on R0x0B. After the frame’s integration period is
complete the readout process commences and the syncs and
data are output. Sensor in snapshot mode can capture a single
image or a sequence of images. The frame rate may only be
controlled by changing the period of the user supplied
EXPOSURE pulse train. The frame synchronization
waveforms for snapshot mode are shown in Figure 17.
CONTROLLER MT9V032
EXPOSURE
SYSCLK
DOUT(9:0
)
PIXCLK
LINE_VALID
FRAME_VALID
Figure 16. Snapshot Mode Frame Synchronization Waveforms
DOUT(9:0)
Figure 17. Snapshot Mode Frame Synchronization Waveforms
XXX XXX XXX
DOUT(9:0
)
LINE_VALID
Exposure Time
LED_OUT
FRAME_VALID
EXPOSURE
DOUT(9:0)
Slave Mode
In slave mode, the exposure and readout are controlled
using the EXPOSURE, STFRM_OUT, and STLN_OUT
pins. When the slave mode is enabled, STFRM_OUT and
STLN_OUT become input pins.
The start and end of integration are controlled by
EXPOSURE and STFRM_OUT pulses, respectively. While
a STFRM_OUT pulse is used to stop integration, it is also
used to enable the readout process.
MT9V032
www.onsemi.com
33
After integration is stopped, the user provides
STLN_OUT pulses to trigger row readout. A full row of data
is read out with each STLN_OUT pulse. The user must
provide enough time between successive STLN_OUT
pulses to allow the complete readout of one row.
It is also important to provide additional STLN_OUT
pulses to allow the sensors to read the vertical blanking rows.
It is recommended that the user program the vertical blank
register (R0x06) with a value of 4, and achieve additional
vertical blanking between frames by delaying the
application of the STFRM_OUT pulse.
The elapsed time between the rising edge of STLN_OUT
and the first valid pixel data is [horizontal blanking register
(R0x05) + 4] clock cycles.
Figure 18. Slave Mode Operation
Exposure
STFRM_OUT
LED_OUT
STLN_OUT
LINE_VALID
(input)
(input)
(input)
(output)
(output)
1row
time
1row
time
98 master
clocks
2 master
clocks
Vertical Blanking
(def=45 lines)
Integration Time
Signal Path
The MT9V032 signal path consists of a programmable
gain, a programmable analog offset, and a 10bit ADC. See
“Black Level Calibration” for the programmable offset
operation description.
Figure 19. Signal Path
Pixel Output
(reset minus signal)
Offset Correction
Voltage (R0x48 or
result of BLC)
Gain Selection
(R0x35 or
result of AGC)
ADC Data
(9:0)
10 (12) bit ADC
C1
C2
+
Σ
×
MT9V032
www.onsemi.com
34
ONCHIP BIASES
ADC Voltage Reference
The ADC voltage reference is programmed through
R0x2C, bits 2:0. The ADC reference ranges from 1.0V to
2.1V. The default value is 1.4V. The increment size of the
voltage reference is 0.1V from 1.0V to 1.6V (R0x2C[2:0]
values 0 to 6). At R0x2C[2:0] = 7, the reference voltage
jumps to 2.1V.
The effect of the ADC calibration does not scale with
VREF. Instead it is a fixed value relative to the output of the
analog gain stage. At default, one LSB of calibration equals
two LSB in output data (1LSBOffset = 2mV, 1LSBADC =
1mV).
It is very important to preserve the correct values of the
other bits in R0x2C. The default register setting is 0x0004.
V_Step Voltage Reference
This voltage is used for pixel high dynamic range
operations, programmable from R0x31 through R0x34.
Chip Version
Chip version registers R0x00 and R0xFF are readonly.
MT9V032
www.onsemi.com
35
WINDOW CONTROL
Registers R0x01 column start, R0x02 Row Start, R0x03
window height (row size), and R0x04 window width
(column size) control the size and starting coordinates of the
window.
The values programmed in the window height and width
registers are the exact window height and width out of the
sensor. The window start value should never be set below
four.
To read out the dark rows set bit 6 of R0x0D. In addition,
bit 7 of R0x0D can be used to display the dark columns in
the image.
MT9V032
www.onsemi.com
36
BLANKING CONTROL
Horizontal blanking and vertical blanking registers
R0x05 and R0x06 respectively control the blanking time in
a row (horizontal blanking) and between frames (vertical
blanking).
Horizontal blanking is specified in terms of pixel
clocks.
Vertical blanking is specified in terms of numbers of
rows.
The actual imager timing can be calculated using Table4
and Table 5 which describe “Row Timing and
FRAME_VALID/LINE_VALID signals.” The minimum
number of vertical blank rows is 4.
MT9V032
www.onsemi.com
37
PIXEL INTEGRATION CONTROL
Total Integration
R0x0B Total Shutter Width (In Terms of Number of
Rows)
This register (along with the window width and horizontal
blanking registers) controls the integration time for the
pixels.
The actual total integration time, tINT, is:
tINT +(Number of rows of integration x row time) )overhead
(eq. 1)
where:
The number of rows integration is equal to the result of
automatic exposure control (AEC) which may vary
from frame to frame, or, if AEC is disabled, the value in
R0x0B
Row time = (R0x04 + R0x05) master clock periods
Overhead = (R0x04 + R0x05 – 255) master clock
periods
Typically, the value of R0x0B (total shutter width) is
limited to the number of rows per frame (which includes
vertical blanking rows), such that the frame rate is not
affected by the integration time. If R0x0B is increased
beyond the total number of rows per frame, it is required to
add additional blanking rows using R0x06 as needed. A
second constraint is that tINT must be adjusted to avoid
banding in the image from light flicker. Under 60Hz flicker,
this means frame time must be a multiple of 1/120 of a
second. Under 50Hz flicker, frame time must be a multiple
of 1/100 of a second.
Changes to Integration Time
With automatic exposure control disabled (R0xAF, bit 0
is cleared to LOW), and if the total integration time (R0x0B)
is changed through the twowire serial interface while
FRAME_VALID is asserted for frame n, the first frame
output using the new integration time is frame (n + 2).
Similarly, when automatic exposure control is enabled, any
change to the integration time for frame n first appears in
frame (n + 2) output.
The sequence is as follows:
1. During frame n, the new integration time is held in
the R0x0B live register.
2. At the start of frame (n + 1), the new integration
time is transferred to the exposure control module.
Integration for each row of frame (n + 1) has been
completed using the old integration time. The
earliest time that a row can start integrating using
the new integration time is immediately after that
row has been read for frame (n + 1). The actual
time that rows start integrating using the new
integration time is dependent on the new value of
the integration time.
3. When frame (n + 1) is read out, it is integrated
using the new integration time. If the integration
time is changed (R0x0B written) on successive
frames, each value written is applied to a single
frame; the latency between writing a value and it
affecting the frame readout remains at two frames.
However, when automatic exposure control is
disabled, if the integration time is changed through
the twowire serial interface after the falling edge
of FRAME_VALID for frame n, the first frame
output using the new integration time becomes
frame (n+3).
FRAME_VALID
LED_OUT
New Integration
Programmed
Actual
Integration
Image Data
Frame Start
Figure 20. Latency When Changing Integration
Int = 200 rows Int = 300 rows
Int = 200 rows Int = 300 rows
Output Image with
Int = 200 rows Output
Image with
Int = 300 rows
MT9V032
www.onsemi.com
38
Exposure Indicator
The exposure indicator is controlled by:
R0x1B LED_OUT control
The MT9V032 provides an output pin, LED_OUT, to
indicate when the exposure takes place. When R0x1B bit 0
is clear, LED_OUT is HIGH during exposure. By using
R0x1B, bit 1, the polarity of the LED_OUT pin can be
inverted.
High Dynamic Range
High dynamic range is controlled by:
R0x08 shutter width 1
R0x09 shutter width 2
R0x0A shutter width control
R0x31R0x34 V_Step voltages
In the MT9V032, high dynamic range (that is, R0x0F, bit
6 = 1) is achieved by controlling the saturation level of the
pixel (HDR or high dynamic range gate) during the exposure
period. The sequence of the control voltages at the HDR gate
is shown in Figure 21. After the pixels are reset, the step
voltage, V_Step, which is applied to HDR gate, is set up at
V1 for integration time t1 then to V2 for time t2, then V3 for
time t3, and finally it is parked at V4, which also serves as
an antiblooming voltage for the photodetector. This
sequence of voltages leads to a piecewise linear pixel
response, illustrated (in approximates) in Figure 21.
VAA(3.3V)
Figure 21. Sequence of Control Voltages at the HDR Gate
Exposure
HDR
Voltage
V1~1.4V V2~1.2V V3~1.0V
V4~0.8V
t1t2t3
VAA(3.3V)
V1~1.4V V2~1.2V V3~1.0V
t1t2t3
Output
Light Intensity
dV1
dV2
dV3
1/t 11/t 22 1/t 3
Figure 22. Sequence of Voltages in a Piecewise Linear Pixel Response
The parameters of the step voltage V_Step which takes
values V1, V2, and V3 directly affect the position of the knee
points in Figure 22.
Light intensities work approximately as a reciprocal of the
partial exposure time. Typically, t1 is the longest exposure,
t2 shorter, and so on. Thus the range of light intensities is
shortest for the first slope, providing the highest sensitivity.
The register settings for V_Step and partial exposures are:
V1 = R0x31, bits 4:0
V2 = R0x32, bits 4:0
V3 = R0x33, bits 4:0
V4 = R0x34, bits 4:0
tINT = t1 + t2 + t3
There are two ways to specify the knee points timing, the
first by manual setting (default) and the second by automatic
knee point adjustment.
When the auto adjust enabler is set to HIGH (LOW by
default), the MT9V032 calculates the knee points
automatically using the following equations:
t1+tINT *t2*t3(eq. 2)
åt2+tINTx(1ń2)R0x0A,bits3:0 (eq. 3)
åt3+tINTx(1ń2)R0x0A,bits7:4 (eq. 4)
As a default for auto exposure, t2 is 1/16 of tINT, t3 is 1/64
of tINT.
MT9V032
www.onsemi.com
39
When the auto adjust enabler is disabled (default), t1, t2,
and t3 may be programmed through the twowire serial
interface:
t1+(R0x08, bits 14:0) (eq. 5)
t2+(R0x09, bits 14:0) *(R0x08,bits 14:0) (eq. 6)
t3+tINT *t1*t2(eq. 7)
tINT may be based on the manual setting of R0x0B or the
result of the AEC. If the AEC is enabled then the auto knee
adjust must also be enabled.
Variable ADC Resolution
By default, ADC resolution of the sensor is 10bit.
Additionally, a companding scheme of 12bit into 10bit is
enabled by the R0x1C (28). This mode allows higher ADC
resolution which means less quantization noise at lowlight,
and lower resolution at high light, where good ADC
quantization is not so critical because of the high level of the
photon’s shot noise.
10bit
Codes
1,024
768
512
256
256 512 1,024 2,048 4,096
12bit
Codes
8 to 1 Companding (2,048 256)
4 to 1 Companding (1,536 384)
2 to 1 Companding (256 128)
No companding (256 256)
Figure 23. 12to 10Bit Companding Chart
MT9V032
www.onsemi.com
40
GAIN SETTINGS
Changes to Gain Settings
When the digital gain settings (R0x80R0x98) are
changed, the gain is updated on the next frame start.
However, the latency for an analog gain change to take effect
depends on the automatic gain control.
If automatic gain control is enabled (R0xAF, bit 1 is set to
HIGH), the gain changed for frame n first appears in frame
(n + 1); if the automatic gain control is disabled, the gain
changed for frame n first appears in frame (n + 2).
Both analog and digital gain change regardless of whether
the integration time is also changed simultaneously.
New Gain
Programmed
Actual
Gain
Image Data
Frame Start
FRAME_VALID
Gain = 3.5X
Gain = 3.0X Gain = 3.5X
Gain = 3.0X
Output Image with
Gain = 3.0X
Output
Image with
Gain = 3.5X
Figure 24. Latency of Analog Gain Change When AGC Is Disabled
MT9V032
www.onsemi.com
41
Analog Gain
Analog gain is controlled by:
R0x35 global gain
The formula for gain setting is:
Gain +Bits[6 : 0] x 0.0625 (eq. 8)
The analog gain range supported in the MT9V032 is
1X4X with a step size of 6.25 percent. To control gain
manually with this register, the sensor must NOT be in AGC
mode. When adjusting the luminosity of an image, it is
recommended to alter exposure first and yield to gain
increases only when the exposure value has reached a
maximum limit.
Analog gain +bits (6 : 0) x 0.0625 for values16 *31 (eq. 9)
Analog gain +bits (6 : 0) ń2x 0.125 for values 32 *64 (eq. 10)
For values 16–31: each LSB increases analog gain
0.0625v/v. A value of 16 = 1X gain. Range: 1X to 1.9375X.
For values 32–64: each 2 LSB increases analog gain
0.125v/v (that is, double the gain increase for 2 LSB).
Range: 2X to 4X. Odd values do not result in gain increases;
the gain increases by 0.125 for values 32, 34, 36, and so on.
Digital Gain
Digital gain is controlled by:
R0x99R0xA4 tile coordinates
R0x80R0x98 tiled digital gain and weight
In the MT9V032, the image may be divided into 25 tiles,
as shown in Figure 25, through the twowire serial interface,
and apply digital gain individually to each tile.
X0/5 X1/5 X2/5 X3/5 X4/5 X5/5
Y0/5
Y2/5
Y1/5
Y3/5
Y4/5
Y5/5
Figure 25. Tiled Sample
x0_y0 x1_y0 x4_y0
x0_y1 x1_y1 x4_y1
x0_y2 x1_y2 x4_y2
x0_y3 x1_y3 x4_y3
x0_y4 x1_y4 x4_y4
Registers 0x990x9E and 0x9F0xA4 represent the
coordinates X0/5X5/5 and Y0/5Y5/5 in Figure 25,
respectively.
Digital gains of registers 0x800x98 apply to their
corresponding tiles. The MT9V032 supports a digital gain
of 0.253.75X.
The formula for digital gain setting is:
Digital gain +Bits [3 : 0] x 0.25 (eq. 11)
Black Level Calibration
Black level calibration is controlled by:
R0x4C
R0x42
R0x46–R0x48
The MT9V032 has automatic black level calibration
onchip, and if enabled, its result may be used in the offset
correction shown in Figure 26.
MT9V032
www.onsemi.com
42
Figure 26. Black Level Calibration Flow Chart
Pixel Output
(reset minus signal)
Offset Correction
Voltage (R0x48 or
result of BLC)
Gain Selection
(R0x35 or
result of AGC)
ADC Data
(9:0)
10 (12) bit ADC
C1
C2
+
Σ
×
VREF
(R0x2C)
The automatic black level calibration measures the
average value of pixels from 2 dark rows (1 dark row if row
bin 4 is enabled) of the chip. (The pixels are averaged as if
they were lightsensitive and passed through the appropriate
gain.)
This row average is then digitally lowpass filtered over
many frames (R0x47, bits 7:5) to remove temporal noise and
random instabilities associated with this measurement.
Then, the new filtered average is compared to a minimum
acceptable level, low threshold, and a maximum acceptable
level, high threshold.
If the average is lower than the minimum acceptable level,
the offset correction voltage is increased by a programmable
offset LSB in R0x4C. (Default step size is 2 LSB Offset =
1 ADC LSB at analog gain = 1X.)
If it is above the maximum level, the offset correction
voltage is decreased by 2 LSB (default).
To avoid oscillation of the black level from below to
above, the region the thresholds should be programmed so
the difference is at least two times the offset DAC step size.
In normal operation, the black level calibration
value/offset correction value is calculated at the beginning
of each frame and can be read through the twowire serial
interface from R0x48. This register is an 8bit signed two’s
complement value.
However, if R0x47, bit 0 is set to “1,” the calibration value
in R0x48 may be manually set to override the automatic
black level calculation result. This feature can be used in
conjunction with the “show dark rows” feature (R0x0D, bit
6) if using an external black level calibration circuit.
The offset correction voltage is generated according to the
following formulas:
Offset Correction Voltage +(8 *bit signed twoȀs complement calibration value, *127to127) x 0.5mV (eq. 12)
ADC input voltage +(Pixel Output Voltage )Offset Correction Voltage) x Analog Gain (eq. 13)
Rowwise Noise Correction
Rowwise noise correction is controlled by the following
registers:
R0x70 row noise control
R0x72 row noise constant
R0x73 dark column start
When the rowwise noise cancellation algorithm is
enabled, the average value of the dark columns read out is
used as a correction for the whole row. The rowwise
correction is in addition to the general black level correction
applied to the whole sensor frame and cannot be used to
replace the latter. The dark average is subtracted from each
pixel belonging to the same row, and then a positive constant
is added (R0x72, bits 7:0). This constant should be set to the
dark level targeted by the black level algorithm plus the
noise expected on the measurements of the averaged values
from dark columns; it is meant to prevent clipping from
negative noise fluctuations.
Pixel value +ADC value *dark column average )row noise constant (eq. 14)
On a perrow basis, the dark column average is calculated
from a programmable number of dark columns (pixels)
values (R0x70, bits 3:0). The default is 10 dark columns. Of
these, the maximum and minimum values are removed and
then the average is calculated. If R0x70, bits 3:0 are set to
“0” (2 pixels), it is essentially equivalent to disabling the
dark average calculation since the average is equal to “0”
after the maximum and minimum values are removed.
R0x73 is used to indicate the starting column address of
dark pixels that the rownoise correction algorithm uses for
calculation. In the MT9V032, dark columns which may be
used are 759–776. R0x73 is used to select the starting
column for the calculation.
One additional note in setting the rownoise correction
register:
777 t(R0x73, bits9 : 0) )number of dark pixels programmed in R0x70, bits3 : 0 *1 (eq. 15)
MT9V032
www.onsemi.com
43
This is to ensure the column pointer does not go beyond
the limit the MT9V032 can support.
Automatic Gain Control and Automatic Exposure
Control
The integrated AEC/AGC unit is responsible for ensuring
that optimal auto settings of exposure and (analog) gain are
computed and updated every frame.
Automatic exposure control (AEC) and automatic gain
control (AGC) can be individually enabled or disabled by
R0xAF. When AEC is disabled (R0xAF[0] = 0), the sensor
uses the manual exposure value in R0x0B. When AGC is
disabled (R0xAF[1] = 0), the sensor uses the manual gain
value in R0x35. See ON Semiconductor Technical Note
TN0981, “MT9V032 AEC and AGC Functions,” for
further details.
MAX. EXPOSURE
(R0xBD)
DESIRED BIN
(desired luminance)
(R0xA5)
MAX. GAIN
(R0x36)
EXP. LPF
(R0xA8)
EXP. SKIP
(R0xA6)
MANUAL EXP.
(R0x08)
AEC ENABLE
(R0Xaf[0])
To exposure
timing control
To analog
gain control
R0xBA
AEC
OUTPUT
R0xBB
AGC OUTPUT
MIN GAIN
MIN EXP
GAIN LPF
(R0xAB)
GAIN SKIP
(R0xA9)
MANUAL GAIN
(R0x35)
AGC ENABLE
(R0xAF[1])
CURRENT BIN
(current luminance
(R0xBC)
AEC
UNIT
HISTOGRAM
GENERATOR
UNIT
AGC
UNIT
1
16
Figure 27. Controllable and Observable AEC/AGC Registers
0
1
1
0
The exposure is measured in rowtime by reading
R0xBB. The exposure range is 1 to 2047. The gain is
measured in gainunits by reading R0xBA. The gain range
is 16 to 63 (unity gain = 16 gainunits; multiply by 1/16 to
get the true gain).
When AEC is enabled (R0xAF[0] = 1), the maximum auto
exposure value is limited by R0xBD; minimum auto
exposure is fixed at 1 row.
When AGC is enabled (R0xAF[1] = 1), the maximum
auto gain value is limited by R0x36; minimum auto gain is
fixed to 16 gainunits.
The exposure control measures current scene luminosity
and desired output luminosity by accumulating a histogram
of pixel values while reading out a frame. The desired
exposure and gain are then calculated from this for
subsequent frame.
Pixel Clock Speed
The pixel clock speed is same as the master clock
(SYSCLK) at 26.66 MHz by default. However, when
column binning 2 or 4 (R0x0D, bit 2 or 3) is enabled, the
pixel clock speed is reduced by half and onefourth of the
master clock speed respectively. See “Read Mode Options”
and “Column Binning” for additional information.
Hard Reset of Logic
The RC circuit for the MT9V032 uses a 10kW resistor and
a 0.1mF capacitor. The rise time for the RC circuit is 1ms
maximum.
Soft Reset of Logic
Soft reset of logic is controlled by:
R0x0C reset
Bit 0 is used to reset the digital logic of the sensor while
preserving the existing twowire serial interface
configuration. Furthermore, by asserting the soft reset, the
sensor aborts the current frame it is processing and starts
a new frame. Bit 1 is a shadowed reset control register bit to
explicitly reset the automatic gain and exposure control
feature.
These two bits are selfresetting bits and also return to “0”
during twowire serial interface reads.
STANDBY Control
The sensor goes into standby mode by setting STANDBY
to HIGH. Once the sensor detects that STANDBY is
asserted, it completes the current frame before disabling the
digital logic, internal clocks, and analog power enable
signal. To release the sensor from the standby mode, reset
MT9V032
www.onsemi.com
44
STANDBY back to LOW. The LVDS must be powered to
ensure that the device is in standby mode. See
“Appendix B PowerOn Reset and Standby Timing” for
more information on standby.
Monitor Mode Control
Monitor mode is controlled by:
R0x0E monitor mode enable
R0xC0 monitor mode image capture control
The sensor goes into monitor mode when R0x0E bit 0 is
set to HIGH. In this mode, the sensor first captures
a programmable number of frames (R0xC0), then goes into
a sleep period for five minutes. The cycle of sleeping for five
minutes and waking up to capture a number of frames
continues until R0x0E bit 0 is cleared to return to normal
operation.
In some applications when monitor mode is enabled, the
purpose of capturing frames is to calibrate the gain and
exposure of the scene using automatic gain and exposure
control feature. This feature typically takes less than 10
frames to settle. In case a larger number of frames is needed,
the value of R0xC0 may be increased to capture more
frames.
During the sleep period, none of the analog circuitry and
a very small fraction of digital logic (including
a fiveminute timer) is powered. The master clock
(SYSCLK) is therefore always required.
MT9V032
www.onsemi.com
45
READ MODE OPTIONS
(Also see “Output Data Format” and “Output Data
Timing”.)
Column Flip
By setting bit 5 of R0x0D the readout order of the columns
is reversed, as shown in Figure 28.
Row Flip
By setting bit 4 of R0x0D the readout order of the rows is
reversed, as shown in Figure 29.
Figure 28. Readout of 6 Pixels in Normal and Column Flip Output Mode
LINE_VALID
Normal readout
DOUT(9:0
)
Reverse readout
DOUT(9:0
)
P4,1
(9:0) P4,2
(9:0) P4,3
(9:0) P4,4
(9:0) P4,5
(9:0) P4,6
(9:0)
P4,n
(9:0) P4,n1
(9:0) P4,n2
(9:0) P4,n3
(9:0)
P4,n4
(9:0) P4,n5
(9:0)
DOUT(9:0)
DOUT(9:0)
Figure 29. Readout of 6 Rows in Normal and Row Flip Output Mode
LINE_VALID
Normal readout
DOUT(9:0
)
Reverse readout
DOUT(9:0
)
Row4
(9:0) Row5
(9:0) Row6
(9:0) Row7
(9:0) Row8
7(9:0) Row9
(9:0)
Row484
(9:0)
Row483
(9:0)
Row482
(9:0) Row481
(9:0)
Row480
7(9:0) Row479
(9:0)
DOUT(9:0)
DOUT(9:0)
Pixel Binning
In addition to windowing mode in which smaller
resolution (CIF, QCIF) is obtained by selecting small
window from the sensor array, the MT9V032 also provides
the ability to show the entire image captured by pixel array
with smaller resolution by pixel binning. Pixel binning is
based on combining signals from adjacent pixels by
averaging. There are two options: binning 2 and binning 4.
When binning 2 is on, 4 pixel signals from 2 adjacent rows
and columns are combined. In binning 4 mode, 16 pixels are
combined from 4 adjacent rows and columns. The image
mode may work in conjunction with image flip. The binning
operation increases SNR but decreases resolution.
Enabling row bin2 and row bin4 improves frame rate by
2x and 4x respectively. The feature of column binning does
not increase the frame rate in less resolution modes.
Row Binning
By setting bit 0 or 1 of R0x0D, only half or onefourth of
the row set is read out, as shown in Figure 30 below. The
number of rows read out is half or onefourth of what is set
in R0x03.
MT9V032
www.onsemi.com
46
Row10
(9:0)
Row4
(9:0) Row5
(9:0) Row6
(9:0) Row7
(9:0) Row8
7(9:0) Row9
(9:0)
LINE_VALID
Normal readout
LINE_VALID
Row Bin 2 readout
LINE_VALID
Row Bin 4 readout
Row11
(9:0)
Row4
(9:0) Row6
(9:0) Row8
(9:0) Row10
(9:0)
Row4
(9:0) Row8
(9:0)
Figure 30. Readout of 8 Pixels in Normal and Row bin Output Mode
DOUT(9:0)
DOUT(9:0)
DOUT(9:0)
Column Binning
In setting bit 2 or 3 of R0x0D, the pixel data rate is slowed
down by a factor of either two or four, respectively. This is
due to the overhead time in the digital pixel data processing
chain. As a result, the pixel clock speed is also reduced
accordingly.
Figure 31. Readout of 8 Pixels in Normal and Column Bin Output Mode
d1234
(9:0)
LINE_VALID
Normal readout
DOUT(9:0
)
PIXCLK
LINE_VALID
Column Bin 2 readout
DOUT(9:0
)
PIXCLK
LINE_VALID
Column Bin 4 readout
DOUT(9:0
)
PIXCLK
D1
(9:0) D3
(9:0) D4
(9:0) D5
(9:0) D6
(9:0) D7
(9:0)
D2
(9:0) D8
(9:0)
D12
(9:0) D34
(9:0) D56
(9:0) D78
(9:0)
d5678
(9:0)
DOUT(9:0)
DOUT(9:0)
DOUT(9:0)
Interlaced Readout
The MT9V032 has two interlaced readout options. By
setting R0x07[2:0] = 1, all the evennumbered rows are read
out first, followed by a number of programmable field
blanking (R0xBF, bits 7:0), and then the oddnumbered
rows and finally vertical blanking (minimum is 4 blanking
rows). By setting R0x07[2:0] = 2, only one field is read out;
consequently, the number of rows read out is half what is set
in R0x03. The row start address (R0x02) determines which
field gets read out; if the row start address is even, the even
field is read out; if row start address is odd, the odd field is
read out.
MT9V032
www.onsemi.com
47
VALID IMAGE Even Field
00 00 00 ………… 00 00 00
00 00 00 ………… 00 00 00
P4,1 P4,2 P4,3…………P4,n1 P4,n
P6,0 P6,1 P6,2…………P6,n1 P6,n
00 00 00 …………………… 00 00 00
00 00 00 …………………… 00 00 00
00 00 00 ………… 00 00 00
00 00 00 ………… 00 00 00
00 00 00 ………… 00 00 00
00 00 00 ………… 00 00 00
Pm2,0 Pm2,2………Pm2,n2 Pm2,n
Pm,2 Pm,2…………Pm,n1 Pm,n
VALID IMAGE Odd Field
HORIZONTAL
BLANKING
FIELD BLANKING
VERTICAL BLANKING
P5,1 P5,2 P5,3…………P5,n1 P5,n
P7,0 P7,1 P7,2…………P7,n1 P7,n
Pm3,1 Pm3,2………Pm3,n1 Pm3,n
Pm,1 Pm,1…………Pm,n1 Pm,n
00 00 00 ……………………………… 00 00 00
00 00 00 ……………………………… 00 00 00
Figure 32. Spatial Illustration of Interlaced Image Readout
When interlaced mode is enabled, the total number of
blanking rows are determined by both field blanking register
(R0xBF) and vertical blanking register (R0x06). The
followings are their equations.
Field Blanking +R0xBF, bits 7 : 0 (eq. 16)
Vertical Blanking +R0x06, bits 8 : 0 *R0xBF, bits 7 : 0(eq. 17)
with
minimum vertical blanking requirement +4(eq. 18)
Similar to progressive scan, FRAME_VALID is logic
LOW during the valid image row only. Binning should not
be used in conjunction with interlaced mode.
LINE_VALID
By setting bit 2 and 3 of R0x74, the LINE_VALID signal
can get three different output formats. The formats for
reading out four rows and two vertical blanking rows are
shown in Figure 33. In the last format, the LINE_VALID
signal is the XOR between the continuous LINE_VALID
signal and the FRAME_VALID signal.
Default
FRAME_VALID
LINE_VALID
Continuously
FRAME_VALID
XOR
FRAME_VALID
LINE_VALID
LINE_VALID
Figure 33. Different LINE_VALID Formats
LVDS Serial (StandAlone/Stereo) Output
The LVDS interface allows for the streaming of sensor
data serially to a standard offtheshelf deserializer up to
five meters away from the sensor. The pixels (and controls)
are packeted—12bit packets for standalone mode and
18bit packets for stereoscopy mode. All serial signalling
(CLK and data) is LVDS. The LVDS serial output could
either be data from a single sensor (standalone) or
streammerged data from two sensors (self and its
stereoscopic slave pair). The appendices describe in detail
the topologies for both standalone and stereoscopic modes.
There are two standard deserializers that can be used. One
for a standalone sensor stream and the other from a
stereoscopic stream. The deserializer attached to a
MT9V032
www.onsemi.com
48
standalone sensor is able to reproduce the standard parallel
output (8bit pixel data, LINE_VALID, FRAME_VALID
and PIXCLK). The deserializer attached to a stereoscopic
sensor is able to reproduce 8bit pixel data from each sensor
(with embedded LINE_VALID and FRAME_VALID) and
pixelclk. An additional (simple) piece of logic is required
to extract LINE_VALID and FRAME_VALID from the
8bit pixel data. Irrespective of the mode
(stereoscopy/standalone), LINE_VALID and
FRAME_VALID are always embedded in the pixel data.
In stereoscopic mode, the two sensors run in lockstep,
implying all state machines are in the same state at any given
time. This is ensured by the sensorpair getting their
sysclks and sysresets in the same instance. Configuration
writes through the twowire serial interface are done in such
a way that both sensors can get their configuration updates
at once. The intersensor serial link is designed in such a
way that once the slave PLL locks and the datadly,
shftclkdly and streamlatencysel are configured, the
master sensor streams good stereo content irrespective of
any variation voltage and/or temperature as long as it is
within specification. The configuration values of datadly,
shftclkdly and streamlatencysel are either
predetermined from the board layout or can be empirically
determined by reading back the stereoerror flag. This flag
gets asserted when the two sensor streams are not in sync
when merged. The combo_reg is used for outofsync
diagnosis.
Figure 34. Serial Output Format for 6x2 Frame
Internal
PIXCLK
Internal
Parallel
Data
Internal
Line_Valid
Internal
Frame_Valid
External
Serial
Data Out
NOTES: 1. External pixel values of 0, 1, 2, 3, are reserved (they only convey control information).
Any raw pixel of value 0, 1, 2 and 3 will be substituted with 4.
2. The external pixel sequence 1023, 0 1023 is a reserved sequence (conveys control
information). Any raw pixel sequence of 1023, 0, 1023 will be substituted with 1023, 4, 1023.
P42P41 P43 P44 P45 P46 P52 P53 P54 P56
P55
P51
1023 0 1023 1 P41 P42 P43 P44 P45 P46 2 1 P51 P52 P53 P54 P55 P56 3
LVDS Output Format
In standalone mode, the packet size is 12 bits (2 frame
bits and 10 payload bits); 10bit pixels or 8bit pixels can be
selected. In 8bit pixel mode (R0xB6[0] = 0), the packet
consists of a start bit, 8bit pixel data (with sync codes), the
line valid bit, the frame valid bit and the stop bit. For 10bit
pixel mode (R0xB6[0] = 1), the packet consists of a start bit,
10bit pixel data, and the stop bit.
Table 9. LVDS PACKET FORMAT IN STANDALONE MODE (Stereoscopy Mode Bit DeAsserted)
12 Bit Packet
Use_10bit_pixels Bit DeAsserted
(8Bit Mode)
Use_10bit_pixels Bit Asserted
(10Bit Mode)
Bit[0] 1’b1(Start bit) 1’b1(Start bit)
Bit[1] PixelData[2] PixelData[0]
Bit[2] PixelData[3] PixelData[1]
Bit[3] PixelData[4] PixelData[2]
Bit[4] PixelData[5] PixelData[3]
Bit[5] PixelData[6] PixelData[4]
Bit[6] PixelData[7] PixelData[5]
Bit[7] PixelData[8] PixelData[6]
Bit[8] PixelData[9] PixelData[7]
Bit[9] Line_Valid PixelData[8]
Bit[10] Frame_Valid PixelData[9]
Bit[11] 1’b0(Stop bit) 1’b0(Stop bit)
In stereoscopic mode (see Figure 47), the packet size is 18
bits (2 frame bits and 16 payload bits). The packet consists
of a start bit, the master pixel byte (with sync codes), the
slave byte (with sync codes), and the stop bit.)
MT9V032
www.onsemi.com
49
Table 10. LVDS PACKET FORMAT IN STEREOSCOPY MODE (Stereoscopy Mode Bit Asserted)
18bit Packet Function
Bit[0] 1’b1 (Start bit)
Bit[1] Master Sensor Pixel Data [2]
Bit[2] Master Sensor Pixel Data [3]
Bit[3] Master Sensor Pixel Data [4]
Bit[4] Master Sensor Pixel Data [5]
Bit[5] Master Sensor Pixel Data [6]
Bit[6] Master Sensor Pixel Data [7]
Bit[7] Master Sensor Pixel Data [8]
Bit[8] Master Sensor Pixel Data [9]
Bit[9] Slave Sensor Pixel Data [2]
Bit[10] Slave Sensor Pixel Data [3]
Bit[11] Slave Sensor Pixel Data [4]
Bit[12] Slave Sensor Pixel Data [5]
Bit[13] Slave Sensor Pixel Data [6]
Bit[14] Slave Sensor Pixel Data [7]
Bit[15] Slave Sensor Pixel Data [8]
Bit[16] Slave Sensor Pixel Data [9]
Bit[17] 1’b0 (Stop bit)
Control signals LINE_VALID and FRAME_VALID can
be reconstructed from their respective preceding and
succeeding flags that are always embedded within the pixel
data in the form of reserved words.
Table 11. RESERVED WORDS IN THE PIXEL DATA STREAM
Pixel Data Reserved Word Flag
0Precedes frame valid assertion
1Precedes line valid assertion
2Succeeds line valid deassertion
3Succeeds frame valid deassertion
When LVDS mode is enabled along with column binning
(bin 2 or bin 4, R0x0D[3:2]), the packet size remains the
same but the serial pixel data stream repeats itself depending
on whether 2X or 4X binning is set:
For bin 2, LVDS outputs double the expected data
(pixel 0,0 is output twice in sequence, followed by pixel
0,1 twice, . . .).
For bin 4, LVDS outputs 4 times the expected data
(pixel 0,0 is output 4 times in sequence followed by
pixel 0,1 times 4, . . .).
The receiving hardware will need to undersample the
output stream getting data either every 2 clocks (bin 2) or
every 4 (bin 4) clocks.
If the sensor provides a pixel whose value is 0,1, 2, or 3
(that is, the same as a reserved word) then the outgoing serial
pixel value is switched to 4
MT9V032
www.onsemi.com
50
ELECTRICAL SPECIFICATIONS
Table 12. DC ELECTRICAL CHARACTERISTICS (VPWR = 3.3V +0.3V; TA = Ambient = 25°C)
Symbol Definition Condition Minimum
Typi
cal Maximum Unit
VIH Input high voltage VPWR 0.5 VPWR + 0.3 V
VIL Input low voltage –0.3 0.8 V
IIN Input leakage current No pullup resistor;
VIN = VPWR or VGND –15.0
15.0 mA
VOH Output high voltage IOH = –4.0mA VPWR 0.7 V
VOL Output low voltage IOL = 4.0mA 0.3 V
IOH Output high current VOH = VDD 0.7 –9.0 mA
IOL Output low current VOL = 0.7 9.0 mA
VAA Analog power supply Default settings 3.0 3.3 3.6 V
IPWRAAnalog supply current Default settings 35.0 60.0 mA
VDD Digital power supply Default settings 3.0 3.3 3.6 V
IPWRDDigital supply current Default settings, CLOAD= 10pF 35.0 60 mA
VAAPIX Pixel array power sup-
ply Default settings 3.0
3.3 3.6 V
IPIX Pixel supply current Default settings 0.5 1.4 3.0 mA
VLVDS LVDS power supply Default settings 3.0 3.3 3.6 V
ILVDS LVDS supply current Default settings 11.0 13.0 15.0 mA
IPWRA Standby Analog standby supply
current STDBY = VDD 2
3 4 mA
IPWRD Standby
Clock Off
Digital standby supply
current with clock off STDBY = VDD, CLKIN = 0 MHz 1
2 4 mA
IPWRD Standby
Clock On
Digital standby supply
current with clock on STDBY= VDD, CLKIN = 27 MHz
1.05 mA
LVDS DRIVER DC SPECIFICATIONS
|VOD|Output differential volt-
age
RLOAD = 100
W ± 1%
250
400 mV
|DVOD|
Change in VOD between
complementary output
states
50 mV
VOS Output offset voltage 1.0 1.2 1.4 mV
DVOS
Change in VOS between
complementary output
states
35 mV
IOS Output current when
driver shorted to ground
±10 ±12 mA
IOZ Output current when
driver is tristate
±1±10 mA
LVDS RECEIVER DC SPECIFICATIONS
VIDTH+ Input differential | VGPD| < 925mV –100 100 mV
Iin Input current ±20 mA
MT9V032
www.onsemi.com
51
Table 13. ABSOLUTE MAXIMUM RATINGS
Symbol Parameter Minimum Maximum Unit
VSUPPLY Power supply voltage (all supplies) –0.3 4.5 V
ISUPPLY Total power supply current 200 mA
IGND Total ground current 200 mA
VIN DC input voltage –0.3 VDD + 0.3 V
VOUT DC output voltage –0.3 VDD + 0.3 V
TSTG1Storage temperature –40 +125 °C
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
5. This is a stress rating only, and functional operation of the device at these or any other conditions above those indicated in the operational
sections of this specification is not implied.
Exposure to absolute maximum rating conditions for extended periods may affect reliability.
Table 14. AC ELECTRICAL CHARACTERISTICS (VPWR = 3.3V ±0.3V; TA = Ambient = 25°C; Output Load = 10pF)
Definition Symbol Condition Min Typ Max Unit
SYSCLK Input clock frequency Note 1 13.0 26.6 27.0 MHz
Clock duty cycle 45.0 50.0 55.0 %
tRInput clock rise time 1 2 5 ns
tFInput clock fall time 1 2 5 ns
tPLHPSYSCLK to PIXCLK
propagation delay
CLOAD = 10pF 3 7 11 ns
tPD PIXCLK to valid DOUT(9:0)
propagation delay
CLOAD = 10pF –2 0 2 ns
tSD Data setup time 14 16 ns
tHD Data hold time 14 16 ns
tPFLR PIXCLK to LINE_VALID
propagation delay
CLOAD = 10pF –2 0 2 ns
tPFLF PIXCLK to FRAME_VALID
propagation delay
CLOAD = 10pF –2 0 2 ns
6. The frequency range specified applies only to the parallel output mode of operation.
Propagation Delays for PIXCLK and Data Out Signals
The pixel clock is inverted and delayed relative to the
master clock. The relative delay from the master clock
(SYSCLK) rising edge to both the pixel clock (PIXCLK)
falling edge and the data output transition is typically 7ns.
Note that the falling edge of the pixel clock occurs at
approximately the same time as the data output transitions.
See Table 14 for data setup and hold times.
Propagation Delays for FRAME_VALID and
LINE_VALID Signals
The LINE_VALID and FRAME_VALID signals change
on the same rising master clock edge as the data output. The
LINE_VALID goes HIGH on the same rising master clock
edge as the output of the first valid pixel’s data and returns
LOW on the same master clock rising edge as the end of the
output of the last valid pixel’s data.
As shown in the Output Data Timing, FRAME_VALID
goes HIGH 143 pixel clocks before the first
MT9V032
www.onsemi.com
52
Figure 35. Propagation Delays for PIXCLK and Data Out Signals
t
tR
tF
DOUT(9:0)
tPLHP
SYSCLK
PIXCLK
tHDSD
tPDPD
Figure 36. Propagation Delays for FRAME_VALID and LINE_VALID Signals
FRAME_VALID
LINE_VALID
FRAME_VALID
LINE_VALID
t
PIXCLK PIXCLK
P
tFLR FLF
PP
PP
Performance Specifications
Table 15 summarizes the specification for each
performance parameter.
Table 15. PERFORMANCE SPECIFICATIONS
Parameter Unit Minimum Typical Maximum Test Number
Sensitivity LSB 400 572 745 1
DSNU LSB N/A 2.3 7.0 2
PRNU % N/A 1.3 4.0 3
Dynamic Range dB 52.0 54.4 N/A 4
SNR dB 33.0 37.3 N/A 5
NOTES: All specifications address operation is at TA=25°C (±3°C) and supply voltage = 3.3V. Image sensor was tested without a lens.
Multiple images were captured and analyzed.
Setup: VDD = VAA = VAAPIX = LVDSVDD = 3.3V. Testing was done with default frame timing and default register settings, with
the exception of AEC/AGC, row noise correction, and auto black level, which were disabled.
Performance definitions are detailed in the following sections.
Test 1: Sensitivity
A flatfield light source (90 lux, color temperature
4400K, broadband, w/ IR cut filter) is used as an
illumination source. Signals are measured in LSB on the
sensor output. A series of four frames are captured and
averaged to obtain a scalar sensitivity output code.
Test 2: Dark Signal Nonuniformity (DSNU)
The image sensor is held in the dark. Analog gain is
changed to the maximum setting of 4X. Signals are
measured in LSB on the sensor output. A series of four
frames are captured and averaged (pixelbypixel) into one
average frame. DSNU is calculated as the standard deviation
of this average frame.
Test 3: Photo Response Nonuniformity (PRNU)
A flatfield light source (90 lux, color temperature
4400K, broadband, with IR cut filter) is used as an
illumination source. Signals are measured in LSB on the
sensor output. Two series of four frames are captured and
averaged (pixelbypixel) into one average frame, one
series is captured under illuminated conditions, and one is
captured in the dark. PRNU is expressed as a percentage
relating the standard deviation of the average frames
difference (illuminated frame dark frame) to the average
illumination level:
MT9V032
www.onsemi.com
53
PRNU +100
1
Np@ȍNp
i+1ǒSillumination(i) *Sdark(i)Ǔ2
Ǹ
1
NpȍNp
i+1(Sillumination(i))
(eq. 19)
Where Sillumination (i) is the signal measured for the ith pixel
from the average illuminated frame, Sdark is the signal
measured for the ith pixel from the average dark frame, and
Np is the total number of pixels contained in the array.
Test 4: Dynamic Range
A temporal noise measurement is made with the image
sensor in the dark and analog gain changed to the maximum
setting of 4X. Signals are measured in LSB on the sensor
output. Two consecutive dark frames are captured.
Temporal noise is calculated as the average pixel value of the
difference frame:
si+ȍNpi+1(S1i *S2i)2
2@Np
Ǹ(eq. 20)
Where S 1i is the signal measured for the ith pixel from the
first frame, S2i is the signal measured for the ith pixel from
the second frame, and Np is the total number of pixels
contained in the array.
The dynamic range is calculated according to the
following formula:
DynamicRange +20
.log (4 1022)
st
(eq. 21)
Where t is the temporal noise measured in the dark at 4X
gain.
Test 5: SignaltoNoise Ratio
A flatfield light source (90 lux, color temperature
4400K, broadband, with IR cut filter) is used as an
illumination source. Signals are measured in LSB on the
sensor output. Two consecutive illuminated frames are
captured. Temporal noise is calculated as the average pixel
value of the difference frame (according to the formula
shown in Test 4).
The signaltonoise ratio is calculated as the ratio of the
average signal level to the temporal noise according to the
following formula:
Signal *to *Noise *Ratio +20
.log
((ȍNpi+1S1i)ńNp)
st
(eq. 22
)
Where σt is the temporal noise measured from the
illuminated frames, S1i is the signal measured for the ith
pixel from the first frame, and Np is the total number of
pixels contained in the array.
TwoWire Serial Bus Timing
The twowire serial bus operation requires certain
minimum master clock cycles between transitions. These
are specified in the following diagrams in master clock
cycles.
Figure 37. Serial Host Interface Start Condition Timing
SCLK
SDATA
44
Figure 38. Serial Host Interface Stop Condition Timing
NOTE: All timing are in units of master clock cycle.
SCLK
SDATA
44
MT9V032
www.onsemi.com
54
Figure 39. Serial Host Interface Data Timing for WRITE
SCLK
4
S
DATA
4
NOTE: SDATA is driven by an off-chip transmitter.
Figure 40. Serial Host Interface Data Timing for READ
SCLK
5
S
DATA
NOTE: SDATA is pulled LOW by the sensor, or allowed to be pulled HIGH by a pull-up resistor off-chip.
Figure 41. Acknowledge Signal Timing After an 8-Bit WRITE to the Sensor
SCLK
Sensor pulls down
S
DATA pin
6
SDATA
3
Figure 42. Acknowledge Signal Timing After an 8-Bit READ from the Sensor
SCLK
Sensor tristates SDATA pin
(turns off pull down)
7
S
DATA
6
NOTE: After a READ, the master receiver must pull down SDATA to acknowledge receipt of data bits. When read sequence is
complete, the master must generate a “No Acknowledge” by leaving SDATA to float HIGH. On the following cycle,
a start or stop bit may be used.
MT9V032
www.onsemi.com
55
TEMPERATURE REFERENCE
The MT9V032 contains a temperature reference circuit
that can be used to measure relative temperatures. Contact
your ON Semiconductor field applications engineer (FAE)
for more information on using this circuit.
Figure 43. Typical Quantum Efficiency Color
0
10
20
30
40
350 450 550 650 750 850 950 1050
Wavelength (nm)
Quantum Efficiency (%)
5
15
25
35 Blue
Red
Green (B)
Green (R)
0
10
20
30
40
350 450 550 650 750 850 950 1050
Wavelength (nm)
Quantum Efficiency (%)
50
60
Figure 44. Typical Quantum Efficiency Monochrome
MT9V032
www.onsemi.com
56
Figure 45. Package Mechanical Drawing (CASE 848AQ)
Seating
plane
4.4
11.43
5.215 5.715
Lid material: borosilicate glass 0.55 thickness
Wall material: alumina ceramic
Substrate material: alumina ceramic 0.7 thickness
8.8
4.4 5.715
4.84
5.215
0.8
TYP 1.75
0.8 TYP
8.8
48 1
10.9 ±0.1
CTR
47X
1.0 ±0.2
48X R 0.15
48X
0.40 ±0.05
11.43
10.9 ±0.1
CTR
Lead finish:
Au plating, 0.50 microns
minimum thickness
over Ni plating, 1.27 microns
minimum thickness
2.3 ±0.2
1.7
Note: 1. Optical center = package center
First
clear
pixel
Optical
center
1
C
A
B
Optical
area
Optical area:
Maximum rotation of optical area relative to package edges: 1º
Maximum tilt of optical area relative to seating plane A:50 microns
Maximum tilt of optical area relative to top of cover glass D:100 microns
A
D
0.90
for reference only
1.400 ±0.125
0.35
for reference only
V CTR
0.20A B C
H CTR
0.20 A B C
Image
sensor die:
0.675 thickness
0.10 A0.05
0.24X
NOTES: 1. All dimensions in millimeters.
2. Optical center = Package center
MT9V032
www.onsemi.com
57
APPENDIX A SERIAL CONFIGURATIONS
With the LVDS serial video output, the deserializer can be
up to 8 meters from the sensor. The serial link can save on
the cabling cost of 14 wires (DOUT[9:0], LINE_VALID,
FRAME_VALID, PIXCLK, GND). Instead, just three wires
(two serial LVDS, one GND) are sufficient to carry the video
signal.
Configuration of Sensor for Stand Alone Serial
Output with Internal PLL
In this configuration, the internal PLL generates the
shiftclk (x12). The LVDS pins SER_DATAOUT_P and
SER_DATAOUT_N must be connected to a deserializer
(clocked at approximately the same system clock
frequency).
Figure 46 shows how a standard offtheshelf deserializer
(National Semiconductor DS92LV1212A) can be used to
retrieve the standard parallel video signals of DOUT(9:0),
LINE_VALID and FRAME_VALID.
Sensor
CLK 26.6 Mhz
Osc.
26.6 Mhz
Osc.
DS92LV1212A
LVDS
SER_DATAOUT
LVDS
SER_DATAIN
LVDS
BYPASS_CLKIN
LVDS
SHIFT_CLKOUT
8 meters (maximum)
LINE_VALID
FRAME_VALID
PIXEL
8bit configuration shown
82
Figure 46. StandAlone Topology
Typical configuration of the sensor:
1. Power up sensor.
2. Enable LVDS driver (set R0xB3[4]= 0).
3. Deassert LVDS powerdown (set R0xB1[1] = 0.
4. Issue a soft reset (set R0x0C[0] = 1 followed by
R0x0C[0] = 0.
If necessary:
5. Force sync patterns for the deserializer to lock (set
R0xB5[0] = 1).
6. Stop applying sync patterns (set R0xB5[0] = 0).
Configuration of Sensor for
Stereoscopic Serial Output with Internal
PPL
In this configuration the internal PLL generates the
shiftclk (x18) in phase with the systemclock. The LVDS
pins SER_DATAOUT_P and SER_DATAOUT_N must be
connected to a deserializer (clocked at approximately the
same system clock frequency).
Figure 47 shows how a standard offtheshelf deserializer
can be used to retrieve back DOUT(9:2) for both the master
and slave sensors. Additional logic is required to extract out
LINE_VALID and FRAME_VALID embedded within the
pixel data stream.
MT9V032
www.onsemi.com
58
SENSOR SENSOR
26.6 MHz
Osc.
DS92LV16
LVDS
SER_DATAOUT
LVDS
SER_DATAIN
LVDS
BYPASS_CLKIN
LVDS
SHIFT_CLKOUT
5 meters (maximum)
PIXEL
FROM
MASTER
PIXEL
FROM
SLAVE
LV and FV are embedded in the data stream
82
Figure 47. Stereoscopic Topology
SLAVE
MASTER
LVDS
SER_DATAOUT
LVDS
SHIFT_CLKOUT
26.6 MHz
Osc.
LVDS
BYPASS_CLKIN
LVDS
SER_DATAIN
Typical configuration of the master and slave sensors:
1. Power up the sensors.
2. Broadcast WRITE to deassert LVDS
powerdown (set R0xB1[1] = 0).
3. Individual WRITE to master sensor putting its
internal PLL into bypass mode (set R0xB1[0] = 1).
4. Broadcast WRITE to both sensors to set the
stereoscopy bit (set R0x07[5] = 1).
5. Make sure all resolution, vertical blanking,
horizontal blanking, window size, and AEC/AGC
configurations are done through broadcast WRITE
to maintain lockstep.
6. Broadcast WRITE to enable LVDS driver (set
R0xB3[4] = 0).
7. Broadcast WRITE to enable LVDS receiver (set
R0xB2[4] = 0).
8. Individual WRITE to master sensor, putting its
internal PLL into bypass mode (set R0xB1[0] = 1).
9. Individual WRITE to slave sensor, enabling its
internal PLL (set R0xB1[0] = 0).
10. Individual WRITE to slave sensor, setting it as a
stereo slave (set R0x07[6] = 1).
11. Individual WRITEs to master sensor to minimize
the intersensor skew (set R0xB2[2:0],
R0xB3[2:0], and R0xB4[1:0] appropriately). Use
R0xB7 and R0xB8 to get lockstep feedback from
stereo_error_flag.
12. Broadcast WRITE to issue a soft reset (set
R0x0C[0] = 1 followed by R0x0C[0] = 0).
NOTE: The stereo_error_flag is set if a mismatch has
occurred at a reserved byte (slave and master
sensors codes at this reserved byte must match).
If the flag is set, steps 11 and 12 are repeated
until the stereo_error_flag remains cleared.
Broadcast and Individual Writes for Stereoscopic
Topology
In stereoscopic mode, the two sensors are required to run
in lockstep. This implies that control logic in each sensor is
in exactly the same state as its pair on every clock. To ensure
this, all inputs that affect control logic must be identical and
arrive at the same time at each sensor.
These inputs include:
system clock
system reset
twowire serial interface clk SCL
twowire serial interface data SDA
MT9V032
www.onsemi.com
59
SLAVE
SENSOR
MASTER
SENSOR
CLK
HOST
26.6 MHz
Osc.
CLKS_CTRL_ADR[0] CLKS_CTRL_ADR[0]
SDASCL SDASCL
SCL
SDA
L
L
L
Host launches SCL and SDA on positive
edge of SYSCLK
All system clock lengths (L) must be equal.
SCL and SDA lengths to each sensor (from the host) must also be equal.
Figure 48. TwoWire Serial Interface Configuration in Stereoscopic Mode
The setup in Figure 48 shows how the two sensors can
maintain lockstep when their configuration registers are
written through the twowire serial interface. A WRITE to
configuration registers would either be broadcast
(simultaneous WRITES to both sensors) or individual
(WRITE to just one sensor at a time). READs from
configuration registers would be individual (READs from
just one sensor at a time).
One of the two serial interface slave address bits of the
sensor is hardwired. The other is controlled by the host. This
allows the host to perform either a broadcast or a onetoone
access.
Broadcast WRITES are performed by setting the same
S_CTRL_ADR input bit for both slave and master sensor.
Individual WRITES are performed by setting opposite
S_CTRL_ADR input bit for both slave and master sensor.
Similarly, individual READs are performed by setting
opposite S_CTRL_ADR input bit for both slave and master
sensor.
MT9V032
www.onsemi.com
60
APPENDIX B POWERON RESET AND STANDBY TIMING
Reset, Clocks, and Standby
There are no constraints concerning the order in which the
various power supplies are applied; however, the MT9V032
requires reset in order operate properly at powerup. Refer
to Figure 49 for the powerup, reset, and standby sequences.
Figure 49. Powerup, Reset, Clock and Standby Sequence
nonLowPower LowPower nonLowPower
Power
down
Wake
up ActiveStandby
PreStandbyActive
Power
up
MIN 20 SYSCLK cycles
Note 3
RESET #
STANDBY
SYSCLK
MIN 10 SYSCLK cycles
Does not
respond to
serial
interface
when
STANDBY = 1
MIN 10 SYSCLK cycles
MIN 10 SYSCLK cycles
DOUT[9:0]
DOUT[9:0]
DATA OUTPUT
SCLK, SDATA
TwoWire Serial I/F
Driven = 0
VDD, VDDLVDS
VAA, VAAPIX
1. All output signals are defined during initial powerup with RESET# held LOW without SYSCLK being active. To properly
reset the rest of the sensor, during initial powerup, assert RESET# (set to LOW state) for at least 750ns after all power
supplies have stabilized and SYSCLK is active (being clocked). Driving RESET# to LOW state does not put the part in
a low power state.
2. Before using twowire serial interface,wait for 10 SYSCLK rising edges after RESET# is deasserted.
3. Once the sensor detects that STANDBY has been asserted, it completes the current frame readout before entering
standby mode. The user must supply enough SYSCLKs to allow a complete frame raedout. See Table 4, “Frame Time,”
for more information.
4. In standby, all video data and synchronization output signals are HighZ.
5. In standby, the twowire serial interface is not active.
Standby Assertion Restrictions
STANDBY cannot be asserted at any time. If STANDBY
is asserted during a specific window within the vertical
blanking period, the MT9V032 may enter a permanent
standby state. This window (that is, dead zone) occurs prior
to the beginning of the new frame readout. The permanent
standby state is identified by the absence of the
FRAME_VALID signal on frame readouts. Issuing a
hardware reset (RESET# set to LOW state) will return the
image sensor to default startup conditions.
This dead zone can be avoided by:
1. Asserting STANDBY during the valid frame
readout time (FRAME_VALID is HIGH) and
maintaining STANDBY assertion for a minimum
of one frame period.
2. Asserting STANDBY at the end of valid frame
readout (falling edge of FRAME_VALID) and
maintaining STANDBY assertion for a minimum
of [5 + R0x06] rowtimes.
When STANDBY is asserted during the vertical blanking
period (FRAME_VALID is LOW), the STANDBY signal
must not change state between [Vertical Blanking Register
(R0x06) 5] rowtimes and [Vertical Blanking Register
+ 5] rowtimes after the falling edge of FRAME_VALID.
MT9V032
www.onsemi.com
61
FRAME_VALID
Vertical Blanking Period
(R0x06) rowtimes
Dead Zone
10 rowtimes
5 rowtimes 5 rowtimes
Figure 50. STANDBY Restricted Location
ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent
coverage may be accessed at www.onsemi.com/site/pdf/PatentMarking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein.
ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards,
regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer
application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not
designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification
in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized
application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such
claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This
literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
N. American Technical Support: 8002829855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81358171050
MT9V032/D
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
19521 E. 32nd Pkwy, Aurora, Colorado 80011 USA
Phone: 3036752175 or 8003443860 Toll Free USA/Canada
Fax: 3036752176 or 8003443867 Toll Free USA/Canada
Email: orderlit@onsemi.com
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
ON Semiconductor:
MT9V032C12STCD3-GEVK MT9V032C12STCH-GEVB MT9V032C12STMH-GEVB