Fast switching H bridge Module fastPACK 0 H Features/ Eigenschaften - 1 phase fast switching IGBT + FRED full bridge 1 phase fast switching IGBT + FRED asymmetric bridge optional NTC temperature sensor Tyco Electronics Rupert-Mayer-Str. 44, D-81359 Munchen power.switches@tycoelectronics.com V23990-P50_-_-PM fastPACK 0 H module types / Produkttypen part - number V23990P501-F-PM P502-F-PM P503-F-PM P500-F-PM Voltage 600V 600V 600V 600V current 15A 20A 30A 35A F-01 types on request and adequate numbers. Schematics/ Schaltplane Type F: 1~ full bridge Type F-01: 1~ asymmetric bridge 17 18 3 16 2 1 14 15 4 5 11 12 13 Tyco Electronics 8 7 6 9 10 Rupert-Mayer-Str. 44, D-81359 Munchen power.switches@tycoelectronics.com V23990-P50_-_-PM fastPACK 0 H Outline / Pinout Toleranz der Pinpositionen: 0.5 mm am Pinende Tolerance of pin positions: 0.5 mm at pinhead Tyco Electronics Rupert-Mayer-Str. 44, D-81359 Munchen power.switches@tycoelectronics.com V23990-P50_-_-PM fastPACK 0 H Montagehinweise / Handling Instruction Montagehinweise... ... fur die Leiterplatte * Das Modul muss vor dem Lotvorgang zuerst in die Locher der Leiterplatte eingerastet werden. Siehe unten * Nach dem Einrasten mussen alle Kontaktpins eingelotet werden. * Die Pins durfen wahrend und nach der Montage bei einer max. Modultemperatur von 25C nicht mehr als 0.2 mm bzw 35 N gedehnt bzw gestaucht werden. * Die Pins durfen bei einer max. Substrattemperatur von 100C mit nicht mehr als 5 N auf Dauer belastet werden. * Eine Vibrationsbelastung der Pins ist unbedingt zu vermeiden. Handling Instructions... ... to the PCB * The module must be fixed to the PCB by clipping into the adequate holes before pin soldering. See below * After fixing all pins must be soldered into the PCB. * During assembly, at a max. module temperature of 25C, the pins should not be drawn or pushed more than 0.2 mm or loaded with a higher force than 35N. * At a maximum substrate-temperature of 100C the load of the pin should not exceed 5N. ...fur den Kuhlkorper * Die Montageflache des Kuhlkorpers mu sauber und frei von Partikeln sein. * Die Ebenheit mu < 0.05 mm auf einer Lange von 100 mm betragen. * die Rauhigkeit sollte geringer als RZ < 0.01 mm sein. ...to the heatsink * the heatsink surface must be clean and particleless. * the flatness must be < 0.05 mm for 100 mm continous. * the surface roughness should be less than RZ < 0.01 mm. ...fur die Warmeleitpaste * homogene Verteilung der Warmeleitpaste auf der ganzen Modulbodenplatte mit einer max. Dicke von 0.05 mm. * Dickere Warmeleitpaste erhoht den Rth. ...to the thermal paste * homogenous applying of the thermal conducting paste over the whole module plate with a thickness of max. 0.05 mm. * Thicker thermal paste can raise the value of the Rth. ... fur die Befestigungsschrauben des Kuhlkorpers * zuerst die Schrauben mit halbem Drehmoment festziehen. * dann mit max. Drehmoment festziehen (falls moglich nach 3 Stunden noch einmal festziehen). ...to the fastening screws of the heatsink * Vibration stress on pins is not allowed * tighten crossover with the half torque first. * tighten crossover with max. torque second (if possible, after 3 hours again) Tabelle 1 Anzugsdrehmomente fur den Kuhlkorper Table 1 Torque instruction to the heatsink Befestigungsschrauben / screws Schraubenunterlegscheibe Auendruchmesser / washer outer diameter Anzugsdrehmoment / mounting torque M4 D= 9mm Tyco Electronics Ma =2.0-2.2Nm Rupert-Mayer-Str. 44, D-81359 Munchen power.switches@tycoelectronics.com V23990-P50_-_-PM fastPACK 0 H PCB holes Tyco Electronics Rupert-Mayer-Str. 44, D-81359 Munchen power.switches@tycoelectronics.com V23990-P50_-_-PM fastPACK 0 H Mounting 1. Insert the modulpins to the PCB 2. Press one short side of the modul gently as shown on figure until two clips of that side are locked 3. Press the other side to lock the remaining two clips. 4. Module in place on PCB: These products are designed for fast switching applications. Tyco Electronics does not recommend the use of its products for other applications. Especially it is not recommended to use the modules in life support applications where such use may directly threaten life or injure due to device failure or malfunction. We reserve the right to make changes of the product at any time without notice, in order to supply the best possible product. Tyco Electronics Rupert-Mayer-Str. 44, D-81359 Munchen power.switches@tycoelectronics.com