LM195QML, LM195QML-SP www.ti.com SNLS194A - NOVEMBER 2010 - REVISED MARCH 2013 LM195QML Ultra Reliable Power Transistors FEATURES DESCRIPTION * * * * * * The LM195 is a fast, monolithic power integrated circuit with complete overload protection. This device, which acts as a high gain power transistor, has included on the chip, current limiting, power limiting, and thermal overload protection making it virtually impossible to destroy from any type of overload. 1 2 * * Internal Thermal Limiting Greater Than 1.0A Output Current 3.0 A Typical Base Current 500 ns Switching Time 2.0V Saturation Base Can be Driven up to 40V Without Damage Directly Interfaces with CMOS or TTL 100% Electrical Burn-in The inclusion of thermal limiting, a feature not easily available in discrete designs, provides virtually absolute protection against overload. Excessive power dissipation or inadequate heat sinking causes the thermal limiting circuitry to turn off the device preventing excessive heating. The LM195 offers a significant increase in reliability as well as simplifying power circuitry. In some applications, where protection is unusually difficult, such as switching regulators, lamp or solenoid drivers where normal power dissipation is low, the LM195 is especially advantageous. The LM195 is easy to use and only a few precautions need be observed. Excessive collector to emitter voltage can destroy the LM195 as with any power transistor. When the device is used as an emitter follower with low source impedance, it is necessary to insert a 5.0k resistor in series with the base lead to prevent possible emitter follower oscillations. Although the device is usually stable as an emitter follower, the resistor eliminates the possibility of trouble without degrading performance. Finally, since it has good high frequency response, supply bypassing is recommended. Connection Diagram Figure 1. 5-Pin TO - Bottom View See NDT0003A Package 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2010-2013, Texas Instruments Incorporated LM195QML, LM195QML-SP SNLS194A - NOVEMBER 2010 - REVISED MARCH 2013 www.ti.com Schematic Diagram Simplified Circuit 1.0 Amp Lamp Flasher These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 2 Submit Documentation Feedback Copyright (c) 2010-2013, Texas Instruments Incorporated Product Folder Links: LM195QML LM195QML-SP LM195QML, LM195QML-SP www.ti.com SNLS194A - NOVEMBER 2010 - REVISED MARCH 2013 Absolute Maximum Ratings (1) Collector to Emitter Voltage 42V Collector to Base Voltage 42V Base to Emitter Voltage (Forward) 42V Base to Emitter Voltage (Reverse) 20V Collector Current Internally Limited Power Dissipation (2) Internally Limited Operating Temperature Range -55C TA +125C TO package -65C TA +150C Storage Temperature Range Lead Temperature (Soldering, 10 sec.) 260C JA Thermal Resistance JC (1) TO package; Still Air at 0.5W 192C/W TO package; 500LF/Min Air Flow at 0.5W 66C/W TO package at 1.0W 29C/W Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not ensure specific performance limits. For ensured specifications and test conditions, see the Electrical Characteristics. The ensured specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. The maximum power dissipation must be derated at elevated temperatures and is dictated by TJmax (maximum junction temperature), JA (package junction to ambient thermal resistance), and TA (ambient temperature). The maximum allowable power dissipation at any temperature is PDmax = (TJmax - TA)/JA or the number given in the Absolute Maximum Ratings, whichever is lower. (2) Quality Conformance Inspection Table 1. Mil-Std-883, Method 5005 - Group A Subgroup Description Temp (C) 1 Static tests at +25 2 Static tests at +125 3 Static tests at -55 4 Dynamic tests at +25 5 Dynamic tests at +125 6 Dynamic tests at -55 7 Functional tests at +25 8A Functional tests at +125 8B Functional tests at -55 9 Switching tests at +25 10 Switching tests at +125 11 Switching tests at -55 12 Settling time at +25 13 Settling time at +125 14 Settling time at -55 LM195H/883 Electrical Characteristics DC Parameter Collector to Emitter Symbol VCE (1) Parameter Conditions IC IMax Operating Voltage Notes See (1) Min Max Unit Subgroups 42 V 1, 2, 3 Parameter tested go-no-go only. Copyright (c) 2010-2013, Texas Instruments Incorporated Product Folder Links: LM195QML LM195QML-SP Submit Documentation Feedback 3 LM195QML, LM195QML-SP SNLS194A - NOVEMBER 2010 - REVISED MARCH 2013 www.ti.com LM195H/883 Electrical Characteristics DC Parameter Base to Emitter Symbol BVBE Parameter Breakdown Voltage ISC Collector Current Conditions Notes See (1) VCE 42V VCE 7V Unit Subgroups 42 V 1, 2, 3 1.2 A 1 Min Max 1 A 2, 3 2 V 1, 2 2.5 V 3 VSat Saturation Voltage IC = 1A IB Base Current 0 VBE 42V, IC IMax 5 A 1, 2, 3 IQ Quiescent Current VCE = 42V, VBE = 0V 5 mA 1, 2, 3 VBk Breakdown Delta VBE Thr (1) Thermal Response VC = 46-42V, IL = 50mA -0.03 0.01 V 1 VC = 46-38V -0.03 0.01 V 1 VC = 50-42V -0.03 0.01 V 1 100S -10 100 mV 1 500S -10 70 mV 1 2mS -10 50 mV 1 20mS -10 10 mV 1 Min Max Unit Subgroups Parameter tested go-no-go only. LM195H/883 Electrical Characteristics AC Parameter Symbol Parameter Conditions Notes tON Response Time VI = 0-2V, RL = 36, V+ = 36V 1.8 S 9, 10, 11 tOFF Response Time VI = 2-0V, RL = 36, V+ = 36V 1.8 S 9, 10, 11 4 Submit Documentation Feedback Copyright (c) 2010-2013, Texas Instruments Incorporated Product Folder Links: LM195QML LM195QML-SP LM195QML, LM195QML-SP www.ti.com SNLS194A - NOVEMBER 2010 - REVISED MARCH 2013 Typical Performance Characteristics Bias Current Quiescent Current Figure 2. Figure 3. Base Emitter Voltage Base Current Figure 4. Figure 5. Saturation Voltage Response Time Figure 6. Figure 7. Copyright (c) 2010-2013, Texas Instruments Incorporated Product Folder Links: LM195QML LM195QML-SP Submit Documentation Feedback 5 LM195QML, LM195QML-SP SNLS194A - NOVEMBER 2010 - REVISED MARCH 2013 www.ti.com Typical Performance Characteristics (continued) Response Time 10V Transfer Function Figure 8. Figure 9. 36V Transfer Function Transconductance Figure 10. Figure 11. Small Signal Frequency Response Figure 12. 6 Submit Documentation Feedback Copyright (c) 2010-2013, Texas Instruments Incorporated Product Folder Links: LM195QML LM195QML-SP LM195QML, LM195QML-SP www.ti.com SNLS194A - NOVEMBER 2010 - REVISED MARCH 2013 Typical Applications 1.0 Amp Voltage Follower *Solid Tantalum Power PNP *Protects against excessive base drive **Needed for stability Time Delay Copyright (c) 2010-2013, Texas Instruments Incorporated Product Folder Links: LM195QML LM195QML-SP Submit Documentation Feedback 7 LM195QML, LM195QML-SP SNLS194A - NOVEMBER 2010 - REVISED MARCH 2013 www.ti.com 1.0 MHz Oscillator 1.0 Amp Negative Regulator Solid Tantalum 1.0 Amp Positive Voltage Regulator Solid Tantalum 8 Submit Documentation Feedback Copyright (c) 2010-2013, Texas Instruments Incorporated Product Folder Links: LM195QML LM195QML-SP LM195QML, LM195QML-SP www.ti.com SNLS194A - NOVEMBER 2010 - REVISED MARCH 2013 Fast Optically Isolated Switch Optically Isolated Power Transistor CMOS or TTL Lamp Interface Two Terminal Current Limiter 40V Switch *Drive Voltage 0V to 10V 42V Copyright (c) 2010-2013, Texas Instruments Incorporated Product Folder Links: LM195QML LM195QML-SP Submit Documentation Feedback 9 LM195QML, LM195QML-SP SNLS194A - NOVEMBER 2010 - REVISED MARCH 2013 www.ti.com 6.0V Shunt Regulator with Crowbar Two Terminal 100 mA Current Regulator Low Level Power Switch Turn ON = 350 mV Turn OFF = 200 mV 10 Submit Documentation Feedback Copyright (c) 2010-2013, Texas Instruments Incorporated Product Folder Links: LM195QML LM195QML-SP LM195QML, LM195QML-SP www.ti.com SNLS194A - NOVEMBER 2010 - REVISED MARCH 2013 Power One-Shot T = R1C R2 = 3R1 R2 82k Emitter Follower *Need for Stability High Input Impedance AC Emitter Follower Fast Follower *Prevents storage with fast fall time square wave drive Copyright (c) 2010-2013, Texas Instruments Incorporated Product Folder Links: LM195QML LM195QML-SP Submit Documentation Feedback 11 LM195QML, LM195QML-SP SNLS194A - NOVEMBER 2010 - REVISED MARCH 2013 www.ti.com Power Op Amp *Adjust for 50 mA quiescent current Solid Tantalum 6.0 Amp Variable Output Switching Regulator *Sixty turns wound on Arnold Type A-083081-2 core. **Four devices in parallel Solid tantalum REVISION HISTORY SECTION Released Revision Section Changes 11/30/2010 A New Release, Corporate format 1 MDS data sheets converted into one Corp. data sheet format. MNLM195-H Rev 0BL will be archived. 03/20/2013 A All Changed layout of National Data Sheet to TI format 12 Submit Documentation Feedback Copyright (c) 2010-2013, Texas Instruments Incorporated Product Folder Links: LM195QML LM195QML-SP PACKAGE OPTION ADDENDUM www.ti.com 25-Oct-2016 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) 5962-8777801XA ACTIVE TO NDT 3 20 TBD Call TI Call TI -55 to 125 LM195H/883 5962-8777801XA Q A CO 5962-8777801XA Q > T LM195H/883 ACTIVE TO NDT 3 20 TBD Call TI Call TI -55 to 125 LM195H/883 5962-8777801XA Q A CO 5962-8777801XA Q > T (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 25-Oct-2016 Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 MECHANICAL DATA NDT0003A H03A (Rev D) www.ti.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2016, Texas Instruments Incorporated Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments: 5962-8777801XA LM195H/883