CD4007UB - Harris Semiconductor - Datasheet.Directory

5-3

CD4000B Series

This section is intended as a guide for circuit and equipment

designers in the operation and application of MOS inte-

grated circuits. It covers general operating and handling con-

siderations with respect to the following critical factors:

• Operating Supply Voltage Range

• Power Dissipation and Derating

• System Noise Considerations

• Power Source Rules

• Gate-oxide Protection Networks

• Input Signals and Ratings

• Chip Assembly and Storage

• Device Mounting

• Testing

More speciﬁc information is then given on signiﬁcant fea-

tures, special design and application requirements, and

standard ratings and electrical characteristics for CMOS B-

series logic circuits, and on CMOS special function circuits

(special interface and display driver circuits).

General Operating and Handling

Considerations

The following paragraphs discuss some key operating and

handling considerations that must be taken into account to

achieve maximum advantage of the CMOS technology.

Additional information on the operation and handling of

CMOS integrated circuits is given in Application Note

AN6525, “Guide to Better Handling and Operation of CMOS

Integrated Circuits”. See Section 8, “How to Use Answer-

FAX”, in this selection guide.

Operating Supply Voltage Range

Because logic systems occasionally experience transient con-

ditions on the power supply line which, when added to the

nominal power-bus voltage, could exceed the safe limits of cir-

cuits connected to the power bus, the recommended operat-

ing supply voltage range is 3V to 18V for B-series devices.

The recommended maximum power supply limit is substan-

tially below the minimum primary breakdown limit for the

devices to allow for limited power supply transient and regula-

tion limits. For circuits that operated in a linear mode over a

portion of the voltage range, such as RC or crystal oscillators,

a minimum supply voltage of 4V is recommended.

Power Dissipation and Derating

The power dissipation of a CMOS integrated circuit is the

sum of a DC (quiescent) component and an AC (dynamic)

components. The DC component is the sum of the net inte-

grated circuit reverse diode junction current and the surface

leakage current times the supply voltage. In standard B-

series logic devices, the DC dissipation typically ranges,

depending upon device complexity, from 100nW to 400nW

for a supply voltage of 10V. Worst-case DC dissipation is the

product of the maximum quiescent current (given in the data

sheet on each device) and the DC supply voltage VDD.

Dynamic power dissipation has three components:

1. The dissipation that results from current that charges and

discharges the external load capacitance of the output

buffers. The dissipation of each output buffer is equal to

CV2f, where C is the load capacitance, V is the supply

voltage, and f is the switching frequency of that output.

2. The dissipation that results from current that charges and

discharges the internal node capacitances.

3. The dissipation caused by the current spikes through the

PMOS and NMOS transistors in series at the instant of

switching. This component amounts to approximately

10% of the total dissipation, shown graphically in the

datasheets of most CMOS circuits.

All CMOS devices are rated at 200mW per package at the

maximum operating ambient temperature rating (TA) of

125oC for all packages. Power ratings for temperatures

below the maximum operating temperature are shown in the

standard CMOS thermal derating chart in Figure 1. This

chart assumes that the device is mounted and soldered (or

placed in a socket) on a PC board; there is natural convec-

tion cooling, with the PC board mounted horizontally; and

the pressure is standard (14.7psia). In addition to the overall

package dissipation, device dissipation per output transistor

is limited to 100mW maximum over the full package operat-

ing temperature range.

FIGURE 1. STANDARD CMOS THERMAL DERATING CHART

System Noise Considerations

In general, CMOS devices are much less sensitive to noise

on power and ground lines than bipolar logic families (such

as TTL or DTL). However, this sensitivity varies as a function

of the power supply voltage, and more importantly as a func-

tion of synchronism between noise spikes and input transi-

tions. Good power distribution in digital systems requires

that the power bus have a low dynamic impedance; for this

purpose, discrete decoupling capacitors should be distrib-

uted across the power bus. A more detailed discussion of

CMOS noise immunity is provided by Application Note

AN6587, “Noise Immunity of B-series CMOS Integrated Cir-

cuits”. See Section 8, “How to Use AnswerFAX”, in this

selection guide.

20 40 60 80 100 120

TA, AMBIENT TEMPERATURE (oC)

600

500

400

300

200

100

PACKAGE DISSIPATION (mW)

85 125

SLOPE = 12mW/oC

Technical Overview

5-4

Technical Overview

Power Source Rules

Figure 2 shows the basic CMOS inverter and its gate-oxide

protection network plus inherent diodes. The safe operating

procedures listed below can be understood by reference to

this inverter.

NOTES:

1. These Diodes are inherently part of the manufacturing process.

2. Diode Breakdown

D1 ≈ 25V

D2 ≈ 50V

R2 << R1

FIGURE 2. BASIC CMOS INVERTER WITH B-SERIES TYPE

PROTECTION NETWORK

1. When separate power supplies are used for the CMOS

device and for the device inputs, the device power supply

should always be turned on before the independent input

signal sources, and the input signals should be turned off

before the power supply is turned off (VSS ≤ VI≤ VDD as

a maximum limit). This rule will prevent over dissipation

and possible damage to the D2 input protection diode

when the device power supply is grounded. When the de-

vice power supply is an open circuit, violation of this rule

can result in undesired circuit operation although device

damage should not result: AC inputs can be rectiﬁed by

diode D2 to act as a power supply.

2. The power supply operating voltage should be kept safely

below the absolute maximum supply rating, as indicated

previously.

3. The power supply polarity for CMOS circuits should not be

reversed. The positive (VDD) terminal should never be

more than 0.5V negative with respect to the negative

(VSS) terminal (VDD - VSS > -0.5V). Reversal of polarities

will forward-bias and short the structural and protection

diode between VDD and VSS.

4. VDD should be equal to or greater than VCC for CMOS

buffers which have two power supplies (except for the

CD40109B, and in particular, for CD4009 and CD4010

CMOS-to-TTL “down” conversion devices).

5. Power source current capability should be limited to as

low a value as reasonable to assure good logic operation.

6. Large values of resistors in series with VDD or VSS should

be avoided; transient turn-on of input protection diodes

can result from drops across such resistors during

switching.

Gate-Oxide Protection Network

A problem occasionally encountered in handling and testing

low power semiconductor devices, including MOS and small

geometry bipolar devices, has been damage to gate oxide

VDD

OUT

D1 D1

D2D2

VSS

COS/MOS

(NOTE 1)

and/or P-N junctions. Figure 3 shows the gate-oxide protec-

tion circuits used to protect CMOS devices from static elec-

tricity damage. Application Note AN6525, “Guide to Better

Handling and Operation of CMOS Integrated Circuits”. See

Section 8, “How to Use AnswerFAX”, in this selection guide.

FIGURE 3A. FOR B-SERIES CMOS PRODUCT

FIGURE 3B. FOR CD4049UB AND CD4050B AND CD40109B

CMOS TYPES

FIGURE 3C. FOR CMOS TRANSMISSION GATES

NOTES:

1. These Diodes are inherently part of the manufacturing process.

2. VCC for CD4049UB and CD4050B

3. Diode Breakdown

D1 ≈ 25V

D2 ≈ 50V

FIGURE 3. GATE-OXIDE PROTECTION NETWORKS USED IN

HARRIS CMOS INTEGRATED CIRCUITS

VDD

OUT

VSS

(NOTE 1)

OUT

VDD (NOTE 2)

VSS

(NOTE 1)

CD4049UB

CD40109B

CD4050B

VDD

VSS

P-WELL

IN/OUT OUT/IN

D1 (NOTE 1)

D2 (NOTE 1)

(NOTE 1) D1

(NOTE 1) D2

GATE 1

GATE 2

N-SUB

5-5

Technical Overview

Input Signals and Ratings

Input signals should be maintained with in the power supply

voltage range, VSS ≤ VI≤ VDD. If the input signal exceeds the

recommended input signal swing range, the input current

should be limited to ±100µA to minimize cross talk between

input signals on adjacent terminals, and also to minimize any

reduction in noise immunity.

The absolute maximum input current rating of ±10mA, shown

in the published data, protects the device against the possible

occurrence of an induced VDD - VSS latch condition, or dam-

age to the input protection diodes. Latch-up conditions are

explained in Application Note AN6525, “Guide to Better Han-

dling and Operation of CMOS Integrated Circuits”. See Sec-

tion 8, “How to Use AnswerFAX”, in this selection guide.

ALL CMOS inputs should be terminated. An exception can

be made in the case of unbuffered NOR and NAND gates

where terminating one of the series inputs to the proper

polarity will not permit current ﬂow caused by a ﬂoating

input. Thus tying low one of the inputs of an unbuffered

NAND gate, or tying high one of the inputs of an unbuffered

NOR gate will satisfy this requirement.

When CMOS inputs are wired to edge card connectors with

CMOS drive coming from another PC board, a shunt resistor

in the range of 100kW should be connected to VDD or VSS,

as applicable, in case the inputs become unterminated with

the power supply on.

When CMOS circuits are driven by TTL logic, a “pull-up”

resistor should be connected from the CMOS input to 5V

(further information is given in Application Note AN6602,

“Interfacing COS/MOS with Other Logic Families”, See Sec-

tion 8, “How to Use AnswerFAX”, in this selection guide.

Output Rules

1. The power dissipation in a CMOS package should not ex-

ceed the rated value for the ambient temperature speci-

ﬁed. The actual dissipation should be calculated when

shorting outputs directly to VDD or VSS, driving low im-

pedance loads, or directly driving the base of P-N-P or

N-P-N bipolar transistor.

2. Output short circuits often result from testing errors or im-

proper board assembly. Shorts on buffer outputs or

across power supplies greater than 5V can damage

CMOS devices.

3. CMOS, like active pull-up TTL, can be connected in the

“wire-OR” configuration because an “on” PMOS and an

“on” NMOS transistor could be directly shorted across the

power supply rails. (Exception: CD40107B)

4. Paralleling inputs and outputs of gates is recommended

only when the gates are within the same IC package.

5. Output loads should return to a voltage within the supply

voltage range VDD to VSS.

6. Large capacitive loads (greater than 5000pF) on CMOS

buffers or high current drivers act like short circuits and

may over dissipate output transistors.

7. Output transistors may be over dissipated by operating

buffers as linear amplifiers or using these types as one

shot or astable multivibrators.

Noise immunity and Noise Margin

The complementary structure of the inverter, common to all

CMOS logic devices, results in a near-ideal input-output

transfer characteristic, with switching point midway (45% to

55%) between the 0 and 1 output logic levels. The result is

high DC noise immunity.

Figure 4 shows a typical transfer curve that may be used to

deﬁne the DC noise immunity of CMOS integrated circuits.

The noise immunity voltage (VIL or VIH) is the noise voltage

at any one input that does not propagate through the sys-

tem. Minimum noise immunity for buffered B-series CMOS

devices is 30%, 30%, and 27%, respectively for supply volt-

ages VDD of 5V, 10V, 15V and 20% of VDD for all unbuffered

gates. The VIL and VIH speciﬁcations deﬁne the maximum

permissible additive noise voltage at an input terminal when

input signals are within 50mV of the supply rails.

FIGURE 4. TYPICAL TRANSFER CURVE FOR A INVERTING

GATE AT VDD = 10V

Noise margin is the difference between the noise-immunity

voltage (VIL or VIH) and the output voltage VO. Noise margin

voltage is the maximum voltage that can be impressed upon

an input voltage VIN (where VIN is the VOL or VOH voltage of

the preceding stage) at any (or all) logic I/O terminals with-

out upsetting the logic or causing any output to exceed the

output voltage (VO) conditions speciﬁed for VIL and VIH rat-

ings. Figure 5 illustrates the noise margin concept in a sim-

ple system. Minimum noise margins for buffered B-series

CMOS devices are 1V, 2V, and 2.5V, respectively, for supply

voltages 5V, 10V, and 15V.

FIGURE 5. NOISE MARGIN EXAMPLE USING INVERTERS

VIL MAX VIH MIN

VIN

VIL (TYP)

VO(HIGH)

VOUT

VO(LOW)

VNML = VIL (MAX) - VO(LOW)

VNML = VO(HIGH) - VIH (MIN)

VIH TYP

012345678910

IH = 3.5V VOL = 0.5V

VDD = 5V VOL = 0.5V

VNML = 1V

VIL = 1.5V

VOH = 4.5V

VNML = 1V

VIH = 3.5V

5-6

Technical Overview

Of the two noise limitation speciﬁcations (noise immunity

and noise margin), noise immunity is more practical for

CMOS devices because CMOS outputs are normally within

50mV of supply rails.

Noise immunity increases as the input pulse width becomes

less than the propagation delay of the circuit. This condition

is often described as AC noise immunity. Further information

on noise immunity is given in Application Note AN6587,

“Noise Immunity of B-series CMOS Integrated Circuits”. See

Section 8, “How to Use AnswerFAX”, in this selection guide.

Clock Rise and Fall Time Requirements

Most CMOS clocked devices have maximum rise and fall

time ratings (normally 5ms to 15ms). With longer rise or fall

times, a device may not function properly because of data

ripple through, false triggering problems, etc. Some B-series

CMOS counters have Schmitt-trigger shaping circuits built

into the clock circuit, removing the restriction for input rise or

fall times. Long rise and fall times on CMOS buffer-type

inputs cause increased power dissipation which may exceed

device capability for operating power supply voltages greater

than 5V.

Parallel Clocking

Process variations leading to differences in input threshold

voltage among random device samples can cause loss of

data between certain synchronously clock sequential cir-

cuits, as shown in Figure 6. This problem can be avoided if

the maximum clock rise time (tRCL) for cascading any two

CMOS sequential devices is limited in accordance with the

following equation:

B-Series Types

where tP = tPHL or tPLH (whichever is smaller) for the unit A in

Figure 6 as speciﬁed on the device data sheet at the speci-

ﬁed value of VDD and loading conditions. Schmitt-trigger cir-

cuits such as the CD4093B are an ideal solution to

applications requiring wave-shipping.

FIGURE 6. ERROR EFFECT THAT RESULTS FROM A SLOW

CLOCK IN CASCADED CIRCUITS

Maximum tRCL

0.8VDD V()

1.15V

------------------------------- tP

×ns()=

VDD

SWITCHING POINT = 0.3VDD

SWITCHING POINT = 0.7VDD

PROPER

ERROR

DQ1 B

0.3VDD

0.7VDD

NOTE: CASCADING WITH SLOW

CLOCK CAN CAUSE ERROR

Three-State Logic

Three-state logic can be easily implemented by use of a

transmission gate in the output circuit; this technique pro-

vides a solution to the wire-OR problem in many cases.

Chip Assembly and Storage

Harris CMOS integrated circuits are provided in a chip from

(H sufﬁx) to allow customer design of special and complex

circuits to suit individual needs. CMOS chips are electrically

identical to and offer the features of their counterparts

sealed in ceramic and plastic packages. The following para-

graphs describe mounting considerations, packaging, ship-

ping and storage criteria, handling criteria, visual inspection

criteria, testing criteria, and bonding pad layout and dimen-

sions for each chip.

Mounting Considerations

All CMOS chips are non-gold backed and require the use of

epoxy mounting, conductive silver paste or equivalent is rec-

ommended. In any case the manufacturer’s recommenda-

tions for storage and use should be followed.

In CMOS circuits MOS-transistor P-channel substrates (N-

type bulk material) are connected to VDD, therefore, when

chips are mounted and a conductive paste is used, care

must be taken to keep the active substrate isolated from

ground or other circuit elements.

Packing, Shipping, and Storage Criteria

Solid-state chips, being small in size and unencapsulated,

are physically fragile and require special handling consider-

ation as follows:

• Chips must be stored under proper conditions to insure that

they are not subjected to a moist and/or contaminated atmo-

sphere that could alter their electrical, physical, or mechani-

cal characteristics. After the shipping container is opened,

the chip must be stored under the following conditions:

- Storage Temperature, 40oC Max

- Relative Humidity, 50% Max

- Clean, Dust-Free Environment

• The user must exercise proper care when handling chips

to prevent even the slightest physical damage to the chip.

• During mounting and lead bonding of chips the user must

use proper assembly techniques to obtain proper electri-

cal, thermal, and mechanical performance.

• After the chip has been mounted and bonded, any neces-

sary procedure must be followed by the user to insure that

these non-hermetic chips are not subjected to a moist and

contaminated atmosphere which might cause the develop-

ment of electrical conductive paths across the relatively

small insulating surfaces. In addition, proper consideration

must be given to the protection of these devices from

other harmful environments which could conceivably affect

their performance and/or reliability.

Handling Criteria

The user should ﬁnd the following suggested precautions

helpful in handling CMOS chips.

5-7

Technical Overview

Because of the extremely small size and fragile nature of

chips, the equipment designer should exercise care in han-

dling these devices.

For additional handling considerations for CMOS devices,

refer to Application Note AN6525, “Guide to Better Handling

and Operation of CMOS Integrated Circuits”. See Section 8,

“How to Use AnswerFAX”, in this selection guide.

• Grounding

- Bonders, pellet pick-up tools, table tops, trim and form

tools, sealing equipment, and other equipment used in

chip handling should be properly grounded.

- The operator should be properly grounded.

• In-Process Handling

- Assemblies or subassemblies of chips should be trans-

ported and stored in conductive carriers.

- All external leads of the assemblies or subassemblies

should be shorted together.

• Bonding Sequence

- Connect VDD ﬁrst to external connections, for example,

terminal 14 of the CD4001BH.

- Remaining functions may be connected to their external

connections in any sequence.

• Testing

- Transport all assemblies of chips in conductive carriers.

- In testing chip assemblies or subassemblies, the opera-

tor should be properly grounded.

Visual Inspection Criteria

All standard commercial CMOS chips undergo a visual inspec-

tion which is patterned after MIL-STD-883, Method 2010, Con-

dition B with modiﬁcations reﬂecting CMOS requirements.

Testing Criteria

CMOS chips are DC electrically tested 100% in accordance

with the same standards prescribed for Harris devices in

standard packages.

Device Testing

Harris CMOS circuits are 100% tested by circuit probe in the

wafer stage and are 100% tested again after they have been

packaged. DC tests of Harris devices are performed at 5V,

10V, 15V, and 20V; functionality is checked at 2.8V, 17V, and

20V. Sample testing is used to assure adherence to quality

requirements and AC speciﬁcations.

Static test, high speed functional and DC parametric tests,

are performed at wafer and package stages by means of a

Teradyne 325 test set or equivalent.

Users should follow the sequences below when testing

CMOS devices:

1. Insert the device into the test socket.

2. Apply VDD.

3. Apply the input signal.

4. Perform the test.

5. On completion of test, remove the input signal.

6. Turn off the power supply (VDD).

7. Remove the device from the test socket and insert it into

a conductive carrier. CMOS devices under test must not

be exposed to electrostatic discharge or forward biasing

of the intrinsic protective diodes shown in Figure 3.

Detailed information on the techniques employed in the test-

ing of Harris CMOS integrated circuits are described in

Application Note AN6532, “Fundamentals of Testing CMOS

Integrated Circuits”. See Section 8, “How to Use Answer-

FAX”, in this selection guide.

Device Mounting

Integrated circuits are normally supplied with lead-tin plated

leads to facilitate soldering into circuit boards. In those rela-

tively few applications requiring welding of the device leads,

rather than soldering, the devices may be obtained with

nickel-plated Kovar leads (See MIL-I-38535). It should be

recognized that this type of plating will not provide complete

protection against lead corrosion in the presence of high

humidity and mechanical stress.

In any method of mounting integrated circuits which involves

bending or forming of the device leads, it is extremely impor-

tant that the lead be supported and clamped between the

bend and the package seal, and that bending be done with

care to avoid damage to lead plating. In no case should the

radius of the bend be less than the diameter of the lead. It is

also extremely important that the ends of bent leads be

straight to assure proper insertion through the holes in the

printed-circuit board.

High Voltage B-Series CMOS

Integrated Circuits

Harris CD4000B series types have a maximum DC supply

voltage rating of -0.5V to 20V, and a recommended operat-

ing supply voltage range of 3V to 18V. The major features of

this series are as follows:

• High Voltage (20V) Ratings

• 100% Tested for Quiescent Current at 20V

• 5V, 10V, and 15V Parametric Ratings

• Standardized, Symmetrical Output Characteristics

• Maximum Input Current of 1µA at 18V Over Full Package

Temperature Range; 100nA at 18V and 25oC

• Noise Margin (Full Package Temperature Range) =

1V at VDD = 5V

2V at VDD = 10V

2.5 V at VDD = 15V

• Meets all requirements of JEDEC Tentative Standard No.

13B, “Standard Speciﬁcations for Description of B-Series

CMOS Devices”.

JEDEC Minimum Standard

Under the sponsorship of the Joint Electron Devices Engi-

neering Council (JEDEC) of the Electronic Industries Associ-

ation (EIA), minimum industrial standards have been

established for the maximum ratings, DC and AC electrical

5-8

Technical Overview

characteristics of B-series CMOS integrated circuits. The

JEDEC standard (JEDEC Tentative Standard No. 13B)

deﬁnes B-series CMOS integrated circuits as a uniform fam-

ily of both buffered and unbuffered types that have an abso-

lute DC supply voltage rating of at least 18V.

Buffered CMOS Devices

These are types in which the output “on” impedance is inde-

pendent of any and all valid input logic conditions, both pre-

ceding and present. All such CMOS products are designated

by sufﬁx “B” following the basic type number.

Unbuffered CMOS Devices

These are types that meet all B-series speciﬁcations except

that the logical outputs are not buffered and the noise-immu-

nity voltages, VIL and VIH, are speciﬁed as 20% and 80%,

respectively, of VDD for operation from 5V, 10V, and 17V and

83%, respectively, of VDD for operation from 15V. All such

CMOS product are designated by the sufﬁx “UB”.

The JEDEC minimum standard also includes in the B-series,

CMOS types that have analog inputs or outputs and in addi-

tion, have maximum ratings and logical input and output

parameters that conform to B-series speciﬁcations wherever

applicable. These CMOS devices are also designated by the

sufﬁx “B”.

All B-series CMOS devices can directly replace their A-series

counterparts in most applications. The UB types are high volt-

age versions of corresponding A-series (unbuffered) types.

Commercial A-series types have been obsoleted and

replaced by B-series counterparts with only a few exceptions

such as the continuing CD4059A types.

The Absolute Maximum Rating - JEDEC table lists the

minimum standards established for the maximum ratings

and recommended operating conditions for B-series CMOS

integrated circuits.

The DC Electrical Speciﬁcation - JEDEC table shows the

JEDEC standards for the DC electrical speciﬁcations of

CMOS B-series integrated circuits.

Standardized Ratings and Static Characteristics

Harris B-series CMOS integrated circuits meet or exceed the

most stringent requirements of the JEDEC B-series speciﬁ-

cations. The Absolute Maximum Ratings table shows the

standardized maximum ratings and recommended operating

supply voltage range for Harris B-series CMOS integrated

circuits. The standardized DC electrical speciﬁcations for

these devices are shown in the DC Electrical Speciﬁcation

table. As with the JEDEC speciﬁcations, the Harris standard-

ized characteristics classify the B-series devices into three

leakage (quiescent device current) categories. Table 1 lists

the Harris types in each category and indicates types that,

although they are still B-series types, differ in one or more

static characteristics.

The Absolute Maximum Ratings table and the DC Electri-

cal Speciﬁcation table show that in a number on important

respects, Harris has established new performance stan-

dards for B-series CMOS logic circuits.

• Tight Limits For All Packages

Harris devices used the same set of limits for all package

styles. The JEDEC standard establishes two sets of limits

for most DC parameters; a tight set for products having a

full operating temperature range of -55oC to +125oC (all

Harris devices), and a relaxed set for products having a

limited temperature range of -40oC to +85oC. Because

Harris supplies only one premium grade of B-series prod-

uct in all package styles (i.e., fall-out chips are not used),

all B-series CMOS devices are speciﬁed to the tight set of

limits only.

• Improved Voltage Rating

All Harris B-series devices are tested to voltages that

insure safe operation at the absolute maximum DC supply

voltage rating of 20V. This higher rating permits greater

derating for reliable 15V operation, permits greater 15V

supply tolerance and peak transients, and permits system

use to 18V with conﬁdence.

• Wider Operating Range

All Harris B-series devices have a recommended maxi-

mum operating voltage of 18V. The higher limit permits

18V system supply operation, and also permits wider

power source tolerance and transients for supplies nor-

mally set up to 18V

• Lower Leakage Current

The JEDEC standard establishes three sets of limits for

quiescent device current (IDD) intended to match chip

complexity to device leakage current as realistically as

possible.

For all three levels of chip complexity, all Harris B-series

devices (regardless of package) conform to the tighter set

of limits established in the standard. In addition, a maxi-

mum rating is speciﬁed at 20V, as well as at 5V, 10V, and

15V. As a result:

- In current limited applications, CMOS users can depend

on one tight leakage limit independent of package style

selected.

- Customer use of CMOS product up through 18V is pro-

tected by a published tight leakage current speciﬁcation at

20V (as well as by an input leakage speciﬁcation at 18V).

• Symmetrical Output

Most Harris B-series devices have balanced complemen-

tary output drive (i.e., the output high current IOH rating is

the same as the output low current IOL rating speciﬁed to

the tighter set of limits established in the JEDEC standard.

The balanced output provides uniform rise and fall time

performance, improved system noise energy (dynamic)

immunity, optimum device speed for both output switching

low-to-high (tPLH) and output switching high-to-low (tPHL),

and in general the identical high and low DC and AC char-

acteristics normally associated with a good complemen-

tary output drive circuit. MOS system design, simulation,

and performance are signiﬁcantly enhanced by equal high

and low DC and AC performance ratings and one tight

speciﬁcation limit for all package styles.

5-9

• Improved Input Current (Leakage) Ratings

All Harris B-series devices (regardless of package) have a

maximum input leakage current (IIN) rating of 100nA spec-

iﬁed at voltages up to 18V, and a maximum limit of 1µA at

the upper limit of the package temperature range. Actually,

the 100nA rating is a practical speciﬁcation limited by the

inability of commercial test equipment to measure lower

currents. Laboratory tests show that input leakage cur-

rents of Harris B-series CMOS devices are signiﬁcantly

lower than this limit, typically ranging from 10pA to 100pA.

• Buffered and Unbuffered Gates

The new industry standard establishes a sufﬁx “UB” for

CMOS products that meet all B-series speciﬁcations

except that the logical outputs of the devices are not buff-

ered and the VIL and VIH speciﬁcations are relaxed. The

sufﬁx “B” deﬁnes only buf fered output devices in which the

output “on” impedance is independent of any and all valid

input logic conditions, both preceding and present.

Harris supplies both buffered “B” and unbuffered “UB” ver-

sions of a few popular NOR and NAND gates to make

available to designers the advantages of both. The follow-

ing table brieﬂy compares the features of the two versions,

a more detailed coverage of the special features of B- and

UB- series CMOS gates is provided by Application Note

AN6558, “Understanding Buffered and Unbuffered CMOS

Characteristics”. See Section 8, “How to Use AnswerF AX”,

in this selection guide.

•Reliability

Harris B-series CMOS integrated circuits incorporate the

latest improvements in processing technology and plastic

and ceramic packaging techniques. Product quality is real

time controlled using accelerated temperature group qual-

ity screening in which measured DC parameters are criti-

cized against tight B-series limits.

Figure 7 through Figure 10 show the standardized N- and

P-channel drain characteristics for B-series CMOS

devices, and Figure 11 through Figure 14 show the nor-

malized variation of output source and sink currents with

respect to temperature and voltage in these devices.

COMPARISON OF “B” AND “UB”

CHARACTERISTIC BUFFERED

VERSION “B” UNBUFFERED

VERSION “UB”

Propagation Delay

(Speed) Moderate Fast

Noise Immunity/Margin Excellent Good

Output Impedance and

Output Transition Time Constant Variable

AC Gain High Medium

Output Oscillation for

Slow inputs Yes No

Input Capacitance Low High

FIGURE 7. TYPICAL OUTPUT LOW (SINK) CURRENT

CHARACTERISTICS FIGURE 8. MINIMUM OUTPUT LOW (SINK) CURRENT

CHARACTERISTICS

FIGURE 9. TYPICAL OUTPUT HIGH (SOURCE) CURRENT CHARACTERISTICS

051015

DS, DRAIN-TO-SOURCE VOLTAGE (V)

IOL, OUTPUT LOW (SINK) CURRENT (mA)

AMBIENT TEMPERATURE, TA = 25oC

GATE-TO-SOURCE VOLTAGE, VGS = 15V

10V

12.5

7.5

2.5

051015

DS, DRAIN-TO-SOURCE VOLTAGE (V)

IOL, OUTPUT LOW (SINK) CURRENT (mA)

GATE-TO-SOURCE VOLTAGE, VGS = 15V

10V

5V AMBIENT TEMPERATURE, TA = 25oC

-30

-25

-20

-15

-10

-5

IOH, OUTPUT HIGH (SOURCE) CURRENT (mA)

GATE-TO-SOURCE VOLTAGE, VGS = -5V

VDS, DRAIN-TO-SOURCE VOLTAGE (V)

-5-10-15-20

-10V

-15V

AMBIENT TEMPERATURE, TA = 25oC

Technical Overview

5-10

FIGURE 10. MINIMUM OUTPUT HIGH (SOURCE) CURRENT

CHARACTERISTICS FIGURE 1 1. V ARIA TION OF NORMALIZED OUTPUT LOW (SINK)

CURRENT IOL AND OUTPUT HIGH (SOURCE)

CURRENT IOH WITH TEMPERATURE

FIGURE 12. VARIATION OF NORMALIZED OUTPUT LOW (SINK)

CURRENT IOL AND OUTPUT HIGH (SOURCE)

CURRENT IOH WITH SUPPLY VOLTAGE

FIGURE 13. VARIATION OF LOW-TO-HIGH (tTLH) AND HIGH-TO-

LOW (tTHL) TRANSITION TIME, AND LOW-TO-HIGH

(tPHL) PROPAGATION DELAY TIME WITH

TEMPERATURE

FIGURE 14. VARIATION OF LOW-TO-HIGH (tTLH) AND HIGH-TO-

LOW (tTHL) TRANSITION TIME WITH SUPPLY

VOLTAGE

FIGURE 15. VARIATION OF TRANSITION TIME (tTHL, tTLH) WITH

LOAD CAPACITANCE

-15

-10

-5

IOH, OUTPUT HIGH (SOURCE) CURRENT (mA)

AMBIENT TEMPERATURE, TA = 25oC

-10V

-15V

VDS, DRAIN-TO-SOURCE VOLTAGE (V)

-5-10-15-20

GATE-TO-SOURCE VOLTAGE, VGS = -5V 2

-100 -50 0 50 100 150

TA, AMBIENT TEMPERATURE (oC)

NORMALIZED SINK, IOL, AND

SOURCE, IOH, CURRENT

1.4

1.2

0.8

0.6

0.4

0.2 051015

DD, SUPPLY VOLTAGE (V)

NORMALIZED SINK, IOL, AND

SOURCE, IOH, CURRENT

-100 -75 -50 -25 0 25 50 75 100 125

NORMALIZED TRANSITION TIME, tTHL, t TLH, AND

PROPAGATION DELAY TIME, tPHL, tPLH

1.4

1.2

0.8

0.6

TA, AMBIENT TEMPERATURE (oC)

VDD, SUPPLY VOLTAGE (V)

3.5

2.5

1.5

0.5 0 2 4 6 8 10 12 14 16

NORMALIZED LOW-TO-HIGH, tTLH, AND

HIGH-TO-LOW , tTHL, TRANSITION TIME

AMBIENT TEMPERATURE, TA = 25oC

tTHL, tTLH, TRANSITION TIME (ns)

CL, LOAD CAPACITANCE (pF)

020406080

100

150

200

AMBIENT TEMPERATURE, TA = 25oC

VDD, SUPPLY VOLTAGE = 5V

100

10V

15V

Technical Overview

5-11

Technical Overview

B-Series AC Electrical Speciﬁcations

B-series AC electrical speciﬁcations for individual types are

under the following conditions: VDD = 5V, 10V, and 15V;

TA= +25oC; CL = 50pF; RL = 200kΩ; tR and tF = 20ns. Figure

13 shows the variation of B-series AC parameter with temper-

ature. Figure 14 shows the variation of output transition time

with supply voltage. Figure 17 shows the variation of the stan-

dardized output transition time with load capacitance.

Maximum propagation delay or transition times for values of

CL other than the speciﬁed 50pF can be determined by use

of the multiplication factor (usually 2) between the typical

and maximum values given in the AC speciﬁcations chart

included in the technical data for each device applied to the

typical curves, and also shown in the device technical data.

B-Series AC Switching Speciﬁcations

The AC Electrical Speciﬁcation table deﬁnes the major

CMOS AC speciﬁcations, with reference to the waveforms

shown in Figure 16 through Figure 19. Test conditions of

VDD, low capacitance (CL), and input conditions are given for

individual types in the published data.

CMOS Special Products

Harris supplies some special CMOS products that have

operating supply voltage ranges and other characteristics

that differ from the standardized data speciﬁed for B-series

CMOS integrated circuits.

These special application types include: interface circuits for

level shifting applications to interface CMOS logic levels with

different logic types; display drivers non-multiplexed, 4 digit,

7 segment LCD types containing all the circuitry necessary

for driving conventional LCD displays without the need for

external components, and a video sync generator function.

FIGURE 16. TRANSITION TIMES AND PROPAGATION DELAY

TIMES, COMBINATION LOGIC

NOTE: Outputs should be switching from 10% VDD to 90% VDD in

accordance with the device truth table.

FIGURE 17. CLOCK PULSE RISE AND F ALL TIMES AND PULSE

WIDTH

tPHL tPLH

tTHL tTLH

90%

50%

10%

50%

10%

INVERTING

OUTPUT

INPUT

GND

VDD

tRtF

90% VDD

CLOCK 90% 50%

10% GND

VDD

tRCLtFCL

50% 50%

tWL tWH

10%

tWL + tWH =fCL

FIGURE 18A.

FIGURE 18B.

FIGURE 18. THREE-STATE PROPAGATION DELAY WAVE

SHAPES AND TEST CIRCUIT

NOTE:

1. (H) or (L) Optional

FIGURE 19. SETUP TIMES, HOLD TIMES, REMOVAL TIME, AND

PROPAGATION DELAY TIMES FOR EDGE

TRIGGERED SEQUENTIAL LOGIC CIRCUITS

50% 10%

90%

VSS

VDD

10%

90% 50%

50%

OUTPUT

DISABLE

OUTPUT LOW

TO OFF

OUTPUT HIGH

TO OFF

OUTPUTS

CONNECTED OUTPUTS

DISCONNECTED OUTPUTS

CONNECTED

20ns 20ns

tPHZ

tPLZ VDD

VOL

VOH

VSS

90%

10%

tPZH

tPZL

IC WITH

THREE-

STATE

OUTPUT

OTHER

INPUTS

OUTPUT

DISABLE

VDD FOR tPLZ AND tPZL

VSS FOR tPHZ AND tPZH

OUTPUT

RL = 1kΩ

50pF

tRCLtFCL

GND

VDD

GND

VDD

50%

90%

10%

GND

CLOCK

INPUT

DATA

INPUT

OUTPUT

SET, RESET

OR PRESET

VDD

50%

50%50%

50%

90%

10%

50%

90%

tREM

tPLH

tSU(H)

(NOTE 1)

tSU(L) (NOTE 1)

tTLH tTHL

tH(L)

(NOTE 1)

tH(H)

(NOTE 1)

tPHL

GND

VDD

5-12

Family Ratings and Speciﬁcations‡

Absolute Maximum Ratings JEDEC Standard for DC Speciﬁcations of B-Series CMOS Integrated Circuits (Note 1 and Note 2)

DC Supply Voltage, VDD . . . . . . . . . . . . . . . . . . . . . . -0.5V to +18V

DC Input Voltage, VIN . . . . . . . . . . . . . . . . . . . . -0.5V to VDD +0.5V DC Input Current, IIN (For Any One Input). . . . . . . . . . . . . . . . . .±10mA

Storage Temperature, TS . . . . . . . . . . . . . . . . . . . .-65oC to +150oC

CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation

of the device at these or any other conditions above those indicated in the operational sections of this speciﬁcation is not implied.

Recommended Operating Conditions

DC Supply Voltage, VDD . . . . . . . . . . . . . . . . . . . . . . . +3V to +15V Operating Temperature Range, TA . . . . . . . . . . . . .-55oC to +125oC

DC Electrical Speciﬁcation JEDEC Standard for DC Speciﬁcations of B-Series CMOS Integrated Circuits

PARAMETERS SYMBOL TEST

CONDITIONS TEMP.

RANGE VDD

(V)

(NOTE 3)

TLOW +25oC(NOTE 4)

THIGH

UNITMIN MAX MIN TYP MAX MIN MAX

Quiescent

Device Current IDD VIN = VSS or VDD

All Valid Input

Combinations

Mil 5 - 0.25 - - 0.25 - 7.5 µA

10 - 0.5 - - 0.5 - 15 µA

Gates 15 - 1 - - 1 - 30 µA

Comm 5 - 1 - - 1 - 7.5 µA

10 - 2 - - 2 - 15 µA

15 - 4 - - 4 - 30 µA

Buffers,

Flip-Flops IDD VIN = VSS or VDD

All Valid Input

Combinations

Mil5-1--1-30µA

10 - 2 - - 2 - 60 µA

15 - 4 - - 4 - 120 µA

Comm 5 - 4 - - 4 - 30 µA

10 - 8 - - 8 - 60 µA

15 - 16 - - 16 - 120 µA

MSI IDD VIN = VSS or VDD

All Valid Input

Combinations

Mil 5 - 5 - - 5 - 150 µA

10 - 10 - - 10 - 300 µA

15 - 20 - - 20 - 600 µA

Comm 5 - 20 - - 20 - 150 µA

10 - 40 - - 40 - 300 µA

15 - 80 - - 80 - 600 µA

Low Level

Output Voltage VOL VIN = VSS or VDD

|IO| <1µAAll 5 - 0.05 - - 0.05 - 0.05 V

10 - 0.05 - - 0.05 - 0.05 V

15 - 0.05 - - 0.05 - 0.05 V

High Level

Output Voltage VOH VIN = VSS or VDD

|IO| <1µAAll 5 4.95 - 4.95 - - 4.95 - V

10 9.95 - 9.95 - - 9.95 - V

15 14.95 - 14.95 - - 14.95 - V

‡ For speciﬁc technical information on each individual device type, refer to the appropriate data sheet in Harris AnswerFAX.

See Section 8, “How to use AnswerFAX”, in this selection guide.

5-13

Input Low V oltage VIL VO = 0.5V or 4.5V

VO = 1V or 9V

VO = 1.5V or 13.5V

|IO| <1µA

All 5 - 1.5 - - 1.5 - 1.5 V

B Types 10 - 3 - - 3 - 3 V

15 - 4 - - 4 - 4 V

UB Types 5 - 1 - - 1 - 1 V

10 - 2 - - 2 - 2 V

15 - 2.5 - - 2.5 - 2.5 V

Input High Voltage VIH VO = 0.5V or 4.5V

VO = 1V or 9V

VO = 1.5V or 13.5V

|IO| <1µA

All 5 3.5 - 3.5 - - 3.5 - V

B Types 10 7 - 7 - - 7 - V

15 11 - 11 - - 11 - V

UB Types 5 4 - 4 - - 4 - V

108-8--8-V

15 12.5 - 12.5 - - 12.5 - V

Output Low (Sink)

Current IOL VO = 0.4V

VIN = 0V or 5V

VO = 0.5V

VIN = 0V or 10V

VO = 1.5V

VIN = 0V or 15V

Mil 5 0.64 - 0.51 - - 0.36 - mA

10 1.6 - 1.3 - - 0.9 - mA

15 4.2 - 3.4 - - 2.4 - mA

Comm 5 0.52 - 0.44 - - 0.36 - mA

10 1.3 - 1.1 - - 0.9 - mA

15 3.6 - 3.0 - - 2.4 - mA

Output High

(Source) Current IOH VO = 4.6V

VIN = 0V or 5V

VO = 9.5V

VIN = 0V or 10V

VO = 13.5V

VIN = 0V or 15V

Mil 5 -0.25 - -0.2 - - -0.14 - mA

10 -0.62 - -0.5 - - -0.35 - mA

15 -1.8 - -1.5 - - -1.1 - mA

Comm 5 -0.2 - -0.16 - - -0.12 - mA

10 -0.5 - -0.4 - - -0.3 - mA

15 -1.4 - -1.2 - - -1.0 - mA

Input Current IIN VIN = 0V or 15V Mil 15 - ±0.1 - - ±0.1 - ±1µA

VIN = 0V or 15V Comm 15 - ±0.3 - - ±0.3 - ±1µA

Three-State

Output Leakage

Current

IOUT Max VIN = 0V or 15V Mil 15 - ±0.4 - - ±0.4 - ±12 µA

VIN = 0V or 15V Comm 15 - ±1.6 - - ±1.6 - ±12 µA

Input Capacitance

Per Unit Load CIN Any Input All -----7.5--pF

NOTES:

1. Voltages referenced to VSS.

2. Reprinted from JEDEC Standard No. 13-B, “JEDEC Standard Specification for Description of B-Series CMOS Devices”.

3. TLOW = -55oC for Military Temperature Range Device, -40oC for Commercial Temperature Device (All Harris Devices).

4. THIGH = +125oC for Military Temperature Range Device, +85oC for Commercial Temperature Range Device.

DC Electrical Speciﬁcation JEDEC Standard for DC Speciﬁcations of B-Series CMOS Integrated Circuits (Continued)

PARAMETERS SYMBOL TEST

CONDITIONS TEMP.

RANGE VDD

(V)

(NOTE 3)

TLOW +25oC(NOTE 4)

THIGH

UNITMIN MAX MIN TYP MAX MIN MAX

Family Ratings and Speciﬁcations‡

‡ For speciﬁc technical information on each individual device type, refer to the appropriate data sheet in Harris AnswerFAX.

See Section 8, “How to use AnswerFAX”, in this selection guide.

5-14

Standardized Absolute Maximum Ratings For B-Series CMOS Integrated Circuits

DC Supply Voltage, VDD

Voltage Reference to VSS Terminal. . . . . . . . . . . . . -0.5V to +20V

Input Voltage, All Inputs . . . . . . . . . . . . . . . . . . . -0.5V to VDD +0.5V

DC Input Current,

For Any One Input. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .±10mA

Lead Temperature (During Soldering)

At Distance 1/16in. ± 1/32in. (1.59mm ± 0.79mm)

from Case for 10s Max . . . . . . . . . . . . . . . . . . . . . . . . . . . +265oC

Power Dissipation Per, PD

TA = -55oC to +100oC . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500mW

TA = +100oC to +125oC. . . Derate Linearly at 12mW/oC to 200mW

Device Dissipation Per Output Transistor

For TA = Full Package Temperature Range

(All Package Test) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100mW

Operating Temperature Range, TA . . . . . . . . . . . . .-55oC to +125oC

Storage Temperature, TSTG . . . . . . . . . . . . . . . . . .-65oC to +150oC

CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation

of the device at these or any other conditions above those indicated in the operational sections of this speciﬁcation is not implied.

Recommended Operating Conditions

Supply, Voltage Range

For TA = Full Package Temperature Range . . . . . . . +3V to +18V

Standardized DC Electrical Speciﬁcation For B-Series CMOS Integrated Circuits

PARAMETERS SYMBOL

TEST CONDITIONS LIMITS +25oC

UNIT

(V) VIN

(V) VDD

(V) -55oC -40oC +85oC +125oC MIN TYP MAX

Quiescent Device

Current IDD Max - 0, 5 5 0.25 0.25 7.5 7.5 - 0.01 0.25 µA

- 0, 10 10 0.5 0.5 15 15 - 0.01 0.5 µA

Gates, Inverters

(Note 1) - 0, 15 15 1 1 30 30 - 0.01 1 µA

- 0, 20 20 5 5 150 150 - 0.02 5 µA

Buffers, Flip-

Flops, Latches,

Multi-Level Gates

(MSI-1 Types)

(Note 1)

- 0, 5 5 1 1 30 30 - 0.02 1 µA

- 0, 10 10 2 2 60 60 - 0.02 2 µA

- 0, 15 15 4 4 120 120 - 0.02 4 µA

- 0, 20 20 20 20 600 600 - 0.04 20 µA

Complex Logic

(MSI-2 Types)

(Note 1)

- 0, 5 5 5 5 150 150 - 0.04 5 µA

- 0, 10 10 10 10 300 300 - 0.04 10 µA

- 0, 15 15 20 20 600 600 - 0.04 20 µA

- 0, 20 20 100 100 3000 3000 - 0.08 100 µA

Output Low (Sink)

Current Min IOL Min 0.4 0, 5 5 0.64 0.61 0.42 0.36 0.51 1 - mA

0.5 0, 10 10 1.6 1.5 1.1 0.9 1.3 2.6 - mA

1.5 0, 15 15 4.2 4 2.8 2.4 3.4 6.8 - mA

Output High (Source)

Current, Min IOH Min 4.6 0, 5 5 -6.4 -0.61 -0.42 -0.36 -0.51 -1 - mA

2.5 0, 5 5 -2 -1.8 -1.3 -1.15 -1.6 -3.2 - mA

9.5 0, 10 10 -1.6 -1.5 -1.1 -0.9 -1.3 -2.6 - mA

13.5 0, 15 15 -4.2 -4 -2.8 -2.4 -3.4 -6.8 - mA

Family Ratings and Speciﬁcations‡

‡ For speciﬁc technical information on each individual device type, refer to the appropriate data sheet in Harris AnswerFAX.

See Section 8, “How to use AnswerFAX”, in this selection guide.

5-15

Family Ratings and Speciﬁcations‡

Output Voltage Low-

Level VOL Max - 0, 5 5 0.05 - 0 0.05 V

- 0, 10 10 0.05 - 0 0.05 V

- 0, 15 15 0.05 - 0 0.05 V

Output Voltage

High-Level VOH Min - 0, 5 5 4.95 4.95 5 - V

- 0, 10 10 9.95 9.95 10 - V

- 0, 15 15 14.95 14.95 15 - V

Input Low Voltage VIL Max 0.5, 4.5 - 5 1.5 - - 1.5 V

1, 9 - 10 3 - - 3 V

B Types 1.5, 13.5 - 15 4 - - 4 V

UB Types 0.5, 4.5 - 5 1 - - 1 V

1, 9 - 10 2 - - 2 V

1.5, 13.5 - 15 2.5 - - 2.5 V

Input High Voltage VIH Max 0.5, 4.5 - 5 3.5 3.5 - - V

1, 9 - 10 7 7 - - V

B Types 1.5, 13.5 - 15 11 11 - - V

UB Types 0.5, 4.5 - 5 4 4 - - V

1, 9 - 10 8 8 - - V

1.5, 13.5 - 15 12.5 12.5 - - V

Input Current IIN Max - 0, 18 18 ±0.1 ±0.1 ±1±1-±10-5 ±0.1 µA

Three-State Output

Leakage Current IOUT Max 0, 18 0, 18 18 ±0.4 ±0.4 ±12 ±12 - ±10-4 ±0.4 µA

NOTE:

1. Classiﬁcations of Harris CMOS B-Series Types are Shown in Table 1.

Standardized DC Electrical Speciﬁcation For B-Series CMOS Integrated Circuits (Continued)

PARAMETERS SYMBOL

TEST CONDITIONS LIMITS +25oC

UNIT

(V) VIN

(V) VDD

(V) -55oC -40oC +85oC +125oC MIN TYP MAX

‡ For speciﬁc technical information on each individual device type, refer to the appropriate data sheet in Harris AnswerFAX.

See Section 8, “How to use AnswerFAX”, in this selection guide.

5-16

AC Electrical Speciﬁcations Deﬁnitions

PARAMETERS SYMBOL MIN MAX NOTES

PROPAGATION DELAY

Outputs Going High to Low tPHL -X-

Outputs Going Low to High tPLH -X-

OUTPUT TRANSITION TIME

Outputs Going High to Low tTHL -X-

Outputs Going Low to High tTLH -X-

PULSE WIDTH

Set, Reset, Preset, Enable, Disable, Strobe, Clock tWL or tWH X-1

Clock Input Frequency fCL - X 1, 2

Clock Input Rise and Fall Time tRCL, tFCL -X-

Set-Up Time tSU X-1

Hold Time tHX-1

Removal Time - Set, Reset, Preset-Enable tREM X-1

THREE-STATE DISABLE DELAY TIMES

High Level to High Impedance tPHZ -X-

High Impedance to Low Level tPZL -X-

Low Level to High Impedance tPLZ -X-

High Impedance to High Level tPZH -X-

NOTES:

1. By placing a deﬁning Min or Max in front of deﬁnition, the limits can change from Min to Max, or vice versa.

2. Clock input waveform should have a 50% duty cycle and be such as to cause the Outputs to be switching from 10% VDD to 90% VDD in

accordance with the device truth table.

TABLE 1. CLASSIFICATION OF HARRIS B-SERIES CMOS INTEGRATED CIRCUITS ACCORDING

TO CIRCUIT COMPLEXITY

GATES/INVERTERS

BUFFERS/FLIP-FLOP/

LATCHES/MULTI-LEVEL

GATES (MSl-1) COMPLEX LOGIC (MSI-2)

CD4001B CD4069UB CD4009UB

(Note 1) C04093B CD4006B CD4055B

(Note 1) CD4532B

CD4001UB CD4070B CD4010B

(Note 1) CD4095B CD4008B CD4056B

(Note 1) CD4536B

CD4002B CD4071B CD4013B CD4096B CD4014B CD4060B CD4541B

CD4007UB CD4072B CD4019B CD4098B CD4015B CD4063B CD4543B

CD4011B CD4073B CD4027B CD4502B

(Note 1) CD4017B CD4067B

(Note 1) CD4555B

CD4011UB CD4075B CD4030B CD4503B CD4018B CD4076B CD4556B

CD4012B CD4077B CD4041UB

(Note 1) CD4504B CD4020B CD4089B CD4560B

Family Ratings and Speciﬁcations‡

‡ For speciﬁc technical information on each individual device type, refer to the appropriate data sheet in Harris AnswerFAX.

See Section 8, “How to use AnswerFAX”, in this selection guide.

5-17

CD4016B

(Note 1) CD4078B CD4042B CD4519B CD4021B CD4094B CD4566B

CD4023B CD4081B CD4043B CD40106B CD4022B CD4097B

(Note 1) CD4585B

CD4025B CD4082B CD4044B CD40107B

(Note 1) CD4024B CD4099B CD4724B

CD4048B CD40117B CD4047B CD40109B

(Note 1) CD4026B CD4508B CD14538B

CD4066B

(Note 1) CD4572UB CD4049UB

(Note 1) CD40174B CD4028B CD4510B CD40100B

CD4068B CD4050B

(Note 1) CD40175B CD4029B CD4511B

(Note 1) CD40102B

CD4085B CD40257B CD4031B CD4512B CD40103B

CD4086B CD4033B CD4514B CD40105B

CD4034B CD4515B CD40110B

(Note 1)

CD4035B CD4516B CD40147B

CD4040B CD4517B CD40160B

CD4045B

(Note 1) CD4518B CD40161B

CD4046B

(Note 1) CD4520B CD40163B

CD4051B

(Note 1) CD4521B CD40192B

CD4052B

(Note 1) CD4522B CD40193B

CD4053B

(Note 1) CD4527B CD40194B

CD4054B

(Note 1) CD4529B

NOTE:

1. Indicates types for which, because of special design requirements, one or more static characteristics differ from the standardized data.

Refer to data pages on these types for speciﬁc differences.

TABLE 1. CLASSIFICATION OF HARRIS B-SERIES CMOS INTEGRATED CIRCUITS ACCORDING

TO CIRCUIT COMPLEXITY (Continued)

GATES/INVERTERS

BUFFERS/FLIP-FLOP/

LATCHES/MULTI-LEVEL

GATES (MSl-1) COMPLEX LOGIC (MSI-2)

Family Ratings and Speciﬁcations

5-18

Enhanced Product

STANDARD IC CIRCUITS

SUFFIX “X”

Burn-In Time (Note 1) 160 Hours

Temperature (Note 1) +125oC

Bias Voltage CD4000B 15V

Special Differs by Type

PRODUCT IDENTIFICATION

All Enhanced Product is Identified by a Suffix “X”

Examples: Standard CD4001BE Enhanced CD4001BEX

NOTE:

1. Or equivalent means equivalent time-temperature/voltage result-

ing in the same activation energy.

PRODUCT FLOW

100% BURN-IN 160 HRS AT +125oC OR EQUIVALENT

100% PARAMETRIC AND FUNCTIONAL TESTS AT +25oC

SAMPLE

PARAMETRIC AND

FUNCTIONAL TESTS

AT +25oC

AQL = 0.025%

ENHANCED PRODUCT

= PRODUCT STATE OR PROCESS

= QUALITY ASSURANCE STEP

STANDARD PRODUCT