3.5 GSPS Direct Digital Synthesizer
with 12-Bit DAC
Data Sheet
AD9914
Rev. D Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©20122014 Analog Devices, Inc. All rights reserved.
Technical Support www.analog.com
FEATURES
3.5 GSPS internal clock speed
Integrated 12-bit DAC
Frequency tuning resolution to 190 pHz
16-bit phase tuning resolution
12-bit amplitude scaling
Programmable modulus
Automatic linear and nonlinear frequency sweeping
capability
32-bit parallel datapath interface
8 frequency/phase offset profiles
Phase noise: −128 dBc/Hz (1 kHz offset at 1396 MHz)
Wideband SFDR < −50 dBc
Serial or parallel I/O control
1.8 V/3.3 V power supplies
Software and hardware controlled power-down
88-lead LFCSP package
PLL REF CLK multiplier
Phase modulation capability
Amplitude modulation capability
APPLICATIONS
Agile LO frequency synthesis
Programmable clock generator
FM chirp source for radar and scanning systems
Test and measurement equipment
Acousto-optic device drivers
Polar modulator
Fast frequency hopping
FUNCTIONAL BLOCK DIAGRAM
Figure 1.
12-BI T DAC
3.5GSPS DDS CORE
TIMING AND CONTROL
10836-001
AD9914 HIGH S P E E D P ARALLE L
MODULATION
PORT
LINEAR
SWEEP
BLOCK
SERIAL OR PARALLE L
DATA P ORT
REF CLK
MULTIPLIER
AD9914 Data Sheet
Rev. D | Page 2 of 48
TABLE OF CONTENTS
Features .............................................................................................. 1
Applications ....................................................................................... 1
Functional Block Diagram .............................................................. 1
Revision History ............................................................................... 2
General Description ......................................................................... 3
Specifications ..................................................................................... 4
DC Specifications ......................................................................... 4
AC Specifications .......................................................................... 5
Absolute Maximum Ratings ............................................................ 8
Thermal Performance .................................................................. 8
ESD Caution .................................................................................. 8
Pin Configuration and Function Descriptions ............................. 9
Typical Performance Characteristics ........................................... 12
Equivalent Circuits ......................................................................... 16
Theory of Operation ...................................................................... 17
Single Tone Mode ....................................................................... 17
Profile Modulation Mode .......................................................... 17
Digital Ramp Modulation Mode .............................................. 17
Parallel Data Port Modulation Mode ....................................... 17
Programmable Modulus Mode ................................................. 17
Mode Priority .............................................................................. 18
Functional Block Detail ................................................................. 19
DDS Core .................................................................................... 19
12-Bit DAC Output .................................................................... 20
DAC Calibration Output ........................................................... 20
Reconstruction Filter ................................................................. 20
Clock Input (REF_CLK/REF_CLK) ........................................ 21
PLL Lock Indication .................................................................. 22
Output Shift Keying (OSK) ....................................................... 22
Digital Ramp Generator (DRG) ............................................... 23
Power-Down Control ................................................................ 27
Programming and Function Pins ................................................. 28
Serial Programming ....................................................................... 31
Control InterfaceSerial I/O ................................................... 31
General Serial I/O Operation ................................................... 31
Instruction Byte .......................................................................... 31
Serial I/O Port Pin Descriptions .............................................. 31
Serial I/O Timing Diagrams ..................................................... 32
MSB/LSB Transfers .................................................................... 32
Parallel Programming (8-/16-Bit) ................................................ 33
Register Map and Bit Descriptions .............................................. 34
Register Bit Descriptions ........................................................... 39
Outline Dimensions ....................................................................... 45
Ordering Guide .......................................................................... 45
REVISION HISTORY
1/14—Rev. C to Rev. D
Changes to Digital Timing Specifications Parameter, Table 2 ..... 5
Changes to Figure 23 ....................................................................... 15
Change to DAC Calibration Output Section ............................... 20
Change to Address 0x02, Table 14 ................................................. 34
Changes to Table 17 ......................................................................... 41
11/13—Rev. B to Rev. C
Changes to Table 2 ............................................................................. 5
Change to Programming and Function Pins Section ................. 30
7/13—Rev. A to Rev. B
Change to CMOS Logic Outputs Parameter, Table 1 ................... 4
Changes to Table 2 ............................................................................. 7
Changes to DDS Core Section ....................................................... 19
Changes to Phase-Locked Loop (PLL) Multiplier Section ........ 21
Changed PLL Charge Pump Section to PLL Charge Pump/
Total Feedback Divider Section; Changes to Table 8, PLL
Loop Filter Components Section, and Figure 34 ........................ 22
Change to Table 14 .......................................................................... 34
Changes to Bits [15:8], Table 17 .................................................... 42
8/12—Rev. 0 to Rev. A
Changes to Features Section ............................................................ 1
Changed Differential Input Voltage Unit from mV p-p to V p-p .... 4
Changes to Tabl e 14 ....................................................................... 34
Changes to Tabl e 16 ....................................................................... 40
Changes to Tabl e 28 ....................................................................... 44
Updated Outline Dimensions ....................................................... 45
7/12—Revision 0: Initial Version
Data Sheet AD9914
Rev. D | Page 3 of 48
GENERAL DESCRIPTION
The AD9914 is a direct digital synthesizer (DDS) featuring a
12-bit DAC. The AD9914 uses advanced DDS technology,
coupled with an internal high speed, high performance DAC
to form a digitally programmable, complete high frequency
synthesizer capable of generating a frequency-agile analog
output sinusoidal waveform at up to 1.4 GHz. The AD9914
enables fast frequency hopping and fine tuning resolution
(64-bit capable using programmable modulus mode). The
AD9914 also offers fast phase and amplitude hopping capability.
The frequency tuning and control words are loaded into the
AD9914 via a serial or parallel I/O port. The AD9914 also
supports a user defined linear sweep mode of operation for
generating linear swept waveforms of frequency, phase, or
amplitude. A high speed, 32-bit parallel data input port is
included, enabling high data rates for polar modulation
schemes and fast reprogramming of the phase, frequency,
and amplitude tuning words.
The AD9914 is specified to operate over the extended industrial
temperature range (see the Absolute Maximum Ratings section).
Figure 2. Detailed Block Diagram
10836-002
32
F0 TO F3
D0 TO D31
PS[2:0]
I/O_UPDATE
POWER-
DOWN
CONTROL
EXT_PWR_DWN
DAC_RSET
AOUT
AOUT
OSK
DROVER
DRCTL
DRHOLD
SYNC_CLK
A
θ
CLOCK
AMPLITUDE ( A)
FREQUENCY (ω)
PHASE (θ)
DIGITAL
RAMP
GENERATOR
2
4MULTICHIP
SYNCHRONIZATION
SYSCLK
PLL
REF_CLK
REF_CLK
AD9914
OUTPUT
SHIFT
KEYING
DATA
ROUTE
AND
PARTITION
CONTROL
3
INTERNAL CLO CK TIM ING
AND CONTROL
ω
Acos (ωt + θ)
Asin (ωt + θ)
SYNC_OUT
SYNC_IN
LOOP_FILTER
MASTER_RESET
DAC
12-BIT
DDS
INTERNAL
PROGRAMMING
REGISTERS
AD9914 Data Sheet
Rev. D | Page 4 of 48
SPECIFICATIONS
DC SPECIFICATIONS
AVDD (1.8V) and DVDD (1.8V) = 1.8 V ± 5%, AVDD (3.3V) and DVDD_I/O (3.3V) = 3.3 V ± 5%, TA = 25°C, RSET = 3.3 kΩ,
IOUT = 20 mA, external reference clock frequency = 3.5 GHz with reference clock (REF CLK) multiplier bypassed, unless otherwise noted.
Table 1.
Parameter Min Typ Max Unit Test Conditions/Comments
SUPPLY VOLTAGE
DVDD_I/O 3.135 3.30 3.465 V Pin 16, Pin 83
DVDD 1.71 1.80 1.89 V Pin 6, Pin 23, Pin 73
AVDD (3.3V) 3.135 3.30 3.465 V Pin 34, Pin 36, Pin 39, Pin 40, Pin 43, Pin 47, Pin 50, Pin 52,
Pin 53, Pin 60
AVDD (1.8V)
1.71
1.89
V
Pin 32, Pin 56, Pin 57
SUPPLY CURRENT See also the total power dissipation specifications
IDVDD_I/O 20 mA Pin 16, Pin 83
I
DVDD
433
mA
Pin 6, Pin 23, Pin 73
IAVDD(3.3V) 640 mA Pin 34, Pin 36, Pin 39, Pin 40, Pin 43, Pin 47, Pin 50, Pin 52,
Pin 53, Pin 60
IAVDD(1.8V) 178 mA Pin 32, Pin 56, Pin 57
TOTAL POWER DISSIPATION
Base DDS Power, PLL Disabled 2392 3091 mW 3.5 GHz, single-tone mode, modules disabled, linear
sweep disabled, amplitude scaler disabled
Base DDS Power, PLL Enabled 2237 2627 mW 2.5 GHz, single-tone mode, modules disabled, linear
sweep disabled, amplitude scaler disabled
Linear Sweep Additional Power 28 mW
Modulus Additional Power 20 mW
Amplitude Scaler Additional
Power
138 mW Manual or automatic
Full Power-Down Mode 400 616 mW Using either the power-down and enable register or the
EXT_PWR_DWN pin
CMOS LOGIC INPUTS
Input High Voltage (VIH) 2.0 DVDD_I/O V
Input Low Voltage (V
IL
)
0.8
V
Input Current (IINH, IINL) ±60 ±200 µA At VIN = 0 V and VIN = DVDD_I/O
Maximum Input Capacitance (CIN) 3 pF
CMOS LOGIC OUTPUTS
Output High Voltage (VOH) 2.7 DVDD_I/O V IOH = 1 mA
Output Low Voltage (VOL) 0.4 V IOL = 1 mA
REF CLK INPUT CHARACTERISTICS REF CLK inputs should always be ac-coupled (both
single-ended and differential)
REF CLK Multiplier Bypassed
Input Capacitance 1 pF Single-ended, each pin
Input Resistance 1.4 Differential
Internally Generated DC Bias
Voltage
V
Differential Input Voltage 0.8 1.5 V p-p
REF CLK Multiplier Enabled
Input Capacitance 1 pF Single-ended, each pin
Input Resistance 1.4 Differential
Internally Generated DC Bias
Voltage
V
Differential Input Voltage 0.8 1.5 V p-p
Data Sheet AD9914
Rev. D | Page 5 of 48
AC SPECIFICATIONS
AVDD (1.8V) and DVDD (1.8V) = 1.8 V ± 5%, AVDD3 (3.3V) and DVDD_I/O (3.3V) = 3.3 V ± 5%, TA = 25°C, RSET = 3.3 kΩ, IOUT =
20 mA, external reference clock frequency = 3.5 GHz with reference clock (REF CLK) multiplier bypassed, unless otherwise noted.
Table 2.
Parameter Min Typ Max Unit Test Conditions/Comments
REF CLK INPUT Input frequency range
REF CLK Multiplier Bypassed
Input Frequency Range 500 3500 MHz Maximum fOUT is 0.4 × fSYSCLK
Duty Cycle 45 55 %
Minimum Differential Input Level 632 mV p-p Equivalent to 316 mV swing on each leg
System Clock (SYSCLK) PLL Enabled
VCO Frequency Range 2400 2500 MHz
VCO Gain (K
V
)
60
MHz/V
Maximum PFD Rate 125 MHz
CLOCK DRIVERS
SYNC_CLK Output Driver
Frequency Range 146 MHz
Duty Cycle 45 50 55 %
Rise Time/Fall Time (20% to 80%) 650 ps
SYNC_OUT Output Driver 10 pF load
Frequency Range 9.1 MHz
Duty Cycle
33
66
%
CFR2 register, Bit 9 = 1
Rise Time (20% to 80%) 1350 ps 10 pF load
Fall Time (20% to 80%) 1670 ps 10 pF load
DAC OUTPUT CHARACTERISTICS
Output Frequency Range (1st Nyquist
Zone)
0 1750 MHz
Output Resistance 50 Ω Single-ended (each pin internally terminated to
AVDD (3.3V))
Output Capacitance 1 pF
Full-Scale Output Current
20.48
mA
Range depends on DAC R
SET
resistor
Gain Error 10 +10 % FS
Output Offset 0.6 μA
Voltage Compliance Range AVDD
0.50
AVDD +
0.50
V
Wideband SFDR See the Typical Performance Characteristics
section
101.1 MHz Output −66 dBc 0 MHz to 1750 MHz
427.5 MHz Output −65 dBc 0 MHz to 1750 MHz
696.5 MHz Output 57 dBc 0 MHz to 1750 MHz
1396.5 MHz Output 52 dBc 0 MHz to 1750 MHz
Narrow-Band SFDR See the Typical Performance Characteristics
section
100.5 MHz Output
95
dBc
±500 kHz
427.5 MHz Output 95 dBc ±500 kHz
696.5 MHz Output 95 dBc ±500 kHz
1396.5 MHz Output −92 dBc ±500 kHz
DIGITAL TIMING SPECIFICATIONS
Time Required to Enter Power-Down 45 ns Power-down mode loses DAC/PLL calibration
settings
Time Required to Leave Power-Down 250 ns Must recalibrate DAC/PLL
Minimum Master Reset time 24 SYSCLK cycles
Maximum DAC Calibration Time (t
CAL
)
135
µs
See the
DAC Calibration Output
section for
formula
Maximum PLL Calibration Time (tREF_CLK) 16 ms PFD rate = 25 MHz
8 ms PFD rate = 50 MHz
Maximum Profile Toggle Rate 2 SYNC_CLK period
AD9914 Data Sheet
Rev. D | Page 6 of 48
Parameter Min Typ Max Unit Test Conditions/Comments
PARALLEL PORT TIMING
Write Timing
Address Setup Time to WR Active 1 ns
Address Hold Time to WR Inactive 0 ns
Data Setup Time to WR Inactive 3.8 ns
Data Hold Time to WR Inactive 0 ns
WR Minimum Low Time 2.1 ns
WR Minimum High Time 3.8 ns
Minimum WR Time 10.5 ns
Read Timing
Address to Data Valid 92 ns
Address Hold to RD Inactive 0 ns
RD Active to Data Valid 69 ns
RD Inactive to Data Tristate 50 ns
RD Minimum Low Time 69 ns
RD Minimum High Time 50 ns
SERIAL PORT TIMING
SCLK Clock Rate (1/tCLK ) 80 MHz SCLK duty cycle = 50%
SCLK Pulse Width High, t
HIGH
1.5
ns
SCLK Pulse Width Low, tLOW 5.1 ns
SDIO to SCLK Setup Time, tDS 4.9 ns
SDIO to SCLK Hold Time, tDH 0 ns
SCLK Falling Edge to Valid Data on
SDIO/SDO, tDV
78 ns
CS to SCLK Setup Time, tS 4 ns
CS to SCLK Hold Time, tH 0 ns
CS Minimum Pulse Width High, tPWH 4 ns
DATA PORT TIMING
D[31:0] Setup Time to SYNC_CLK 2 ns
D[31:0] Hold Time to SYNC_CLK 0 ns
F[3:0] Setup Time to SYNC_CLK 2 ns
F[3:0] Hold Time to SYNC_CLK 0 ns
IO_UPDATE Pin Setup Time to
SYNC_CLK
2 ns
IO_UPDATE Pin Hold Time to
SYNC_CLK
0 ns
Profile Pin Setup Time to SYNC_CLK 2 ns
Profile Pin Hold Time to SYNC_CLK 0 ns
DR_CTL/DR_HOLD Setup Time to
SYNC_CLK
2 ns
DR_CTL/DR_HOLD Hold Time to
SYNC_CLK
0 ns
Data Sheet AD9914
Rev. D | Page 7 of 48
Parameter Min Typ Max Unit Test Conditions/Comments
DATA LATENCY (PIPELINE DELAY) SYSCLK cycles = fS = system clock frequency
in GHz
Single Tone Mode or Profile Mode
(Matched Latency Disabled)
Frequency 318 SYSCLK cycles OSK disabled
342 SYSCLK cycles OSK enabled
Phase 294 SYSCLK cycles OSK disabled
318
SYSCLK cycles
OSK enabled
Amplitude 102 SYSCLK cycles OSK enabled
Single Tone Mode or Profile Mode
(Matched Latency Enabled)
Frequency 318 SYSCLK cycles OSK disabled
342 SYSCLK cycles OSK enabled
Phase 318 SYSCLK cycles OSK disabled
342 SYSCLK cycles OSK enabled
Amplitude 342 SYSCLK cycles OSK enabled
Modulation Mode with 32-Bit Parallel
Port (Matched Latency Disabled)
Frequency 318 SYSCLK cycles OSK disabled
342 SYSCLK cycles OSK enabled
Phase 294 SYSCLK cycles OSK disabled
318 SYSCLK cycles OSK enabled
Amplitude 102 SYSCLK cycles OSK enabled
Modulation Mode with 32-Bit Parallel
Port (Matched Latency Enabled)
Frequency 318 SYSCLK cycles OSK disabled
342 SYSCLK cycles OSK enabled
Phase 318 SYSCLK cycles OSK disabled
342 SYSCLK cycles OSK enabled
Amplitude 342 SYSCLK cycles OSK enabled
Sweep Mode (Match Latency Disabled)
Frequency 342 SYSCLK cycles OSK disabled
366 SYSCLK cycles OSK enabled
Phase 318 SYSCLK cycles OSK disabled
342 SYSCLK cycles OSK enabled
Amplitude 126 SYSCLK cycles OSK enabled
Sweep Mode (Match Latency Enabled)
Frequency
342
SYSCLK cycles
OSK disabled
366 SYSCLK cycles OSK enabled
Phase 342 SYSCLK cycles OSK disabled
366 SYSCLK cycles OSK enabled
Amplitude 366 SYSCLK cycles OSK enabled
AD9914 Data Sheet
Rev. D | Page 8 of 48
ABSOLUTE MAXIMUM RATINGS
Table 3.
Parameter Rating
AVDD (1.8 V), DVDD (1.8 V) Supplies 2 V
AVDD (3.3 V), DVDD_I/O (3.3 V) Supplies 4 V
Digital Input Voltage 0.7 V to +4 V
Digital Output Current 5 mA
Storage Temperature Range
65°C to +150°C
Operating Temperature Range 40°C to +85°C
Maximum Junction Temperature 150°C
Lead Temperature (10 sec Soldering) 300°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
THERMAL PERFORMANCE
Table 4.
Symbol Description Value1 Unit
θJA Junction-to-ambient thermal
resistance (still air) per JEDEC
JESD51-2
24.1 °C/W
θJMA Junction-to-ambient thermal
resistance (1.0 m/sec airflow)
per JEDEC JESD51-6
21.3 °C/W
θJMA Junction-to-ambient thermal
resistance (2.0 m/sec air flow)
per JEDEC JESD51-6
20.0 °C/W
θ
JB
Junction-to-board thermal
resistance (still air) per JEDEC
JESD51-8
13.3
°C/W
ΨJB Junction-to-board characterization
parameter (still air) per JEDEC
JESD51-6
12.8 °C/W
θJC
Junction-to-case thermal resistance
2.21
°C/W
ΨJT Junction-to-top-of-package
characterization parameter (still air)
per JEDEC JESD51-2
0.23 °C/W
1 Results are from simulations. PCB is JEDEC multilayer. Thermal performance
for actual applications requires careful inspection of the conditions in the
application to determine if they are similar to those assumed in these
calculations.
ESD CAUTION
Data Sheet AD9914
Rev. D | Page 9 of 48
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
Figure 3. Pin Configuration
Table 5. Pin Function Descriptions
Pin No. Mnemonic I/O1 Description
1, 2, 13 to 15, 68
to 72, 75 to 81,
87, 88
D5 to D7, D16 to
D31, D27 to D31
I/O Parallel Port Pins. The 32-bit parallel port offers the option for serial or parallel programming
of the internal registers. In addition, the parallel port can be configured to provide direct FSK,
PSK, or ASK (or combinations thereof) modulation data. The 32-bit parallel port configuration
is set by the state of the four function pins (F0 to F3).
3 D15/A7 I/O Parallel Port Pin/Address Line. The state of the F0 to F3 function pins determines if this pin
acts as a line for direct FSK, PSK, or ASK data or as an address line for programming the
internal registers.
4 D14/A6 I/O Parallel Port Pin/Address Line. The state of the F0 to F3 function pins determines if this pin
acts as a line for direct FSK, PSK, or ASK data or as an address line for programming the
internal registers.
5 D13/A5 I/O Parallel Port Pin/Address Line. The state of the F0 to F3 function pins determines if this pin
acts as a line for direct FSK, PSK, or ASK data or as an address line for programming the
internal registers.
8 D12/A4 I/O Parallel Port Pin/Address Line. The state of the F0 to F3 function pins determines if this pin
acts as a line for direct FSK, PSK, or ASK data or as an address line for programming the
internal registers.
9 D11/A3 I/O Parallel Port Pin/Address Line. The state of the F0 to F3 function pins determines if this pin
acts as a line for direct FSK, PSK, or ASK data or as an address line for programming the
internal registers.
10 D10/A2 I/O Parallel Port Pin/Address Line. Multipurpose pin depending on the state of the function pins
(F0 to F3). The state of the F0 to F3 function pins determines if this pin acts as a line for direct
FSK, PSK, or ASK data or as an address line for programming the internal registers.
11 D9/A1 I/O Parallel Port Pin/Address Line. Multipurpose pin depending on the state of the function pins
(F0 to F3). The state of the F0 to F3 function pins determines if this pin acts as a line for direct
FSK, PSK, or ASK data or as an address line for programming the internal registers.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
D17
D16
D15/A7
D14/A6
D13/A5
DVDD (1.8V)
DGND
D12/A4
D11/A3
D10/A2
D9/A1
D8/A0
D7
D6
D5
DVDD_I /O ( 3.3V) 17DGND 18D4/SYNCIO 19D3/SDO 20D2/SDIO/WR
23
24
25
26
27
28
29
30
31
32
33
34
36
37
DVDD (1.8V)
DGND
PS0
PS1
PS2
F0
F1
F2
F3
AVDD (1.8V)
AGND
AVDD (3.3V) 35
AGND
AVDD (3.3V)
AGND 38AGND 39AVDD (3.3V) 40AVDD (3.3V) 41
AOUT
58
57
56
55
54
53
52
51
50
49
48
47
46
45
LOOP_FILTER
59 REF
60 AVDD (3.3V)
61 SYNC_OUT
62 SYNC_IN
63 DRCTL
64 DRHOLD
65 DROVER
66 OSK
AVDD (1.8V)
AVDD (1.8V)
REF CLK
REF CLK
AVDD (3.3V)
AVDD (3.3V)
AGND
AVDD (3.3V)
AGND
DAC_RSET
AVDD (3.3V)
AGND
DAC_BP
78
77
76
75
74
73
72
71
70
69
68
67
D23
79 D22
80 D21
81 D20
82 SYNC_CLK
83 DVDD_I /O ( 3.3V)
84 DGND
85 MASTER_RESET
86 I/O_UPDATE
87 D19
88 D18
D24
D25
D26
DGND
DVDD (1.8V)
D27
D28
D29
D30
D31
EXT_PWR_DWN
NOTES
1. THE EP AD M US T BE S OLDE RE D TO GROUND.
10836-003
21D1/SCLK/RD 22D0/CS/PWD
42AOUT 43AVDD ( 3.3V) 44AGND
AD9914
TOP VIEW
(No t t o Scal e)
AD9914 Data Sheet
Rev. D | Page 10 of 48
Pin No. Mnemonic I/O1 Description
12 D8/A0 I/O Parallel Port Pin/Address Line. The state of the F0 to F3 function pins determines if this pin
acts as a line for direct FSK, PSK, or ASK data or as an address line for programming the
internal registers.
18 D4/SYNCIO I Parallel Port Pin/Serial Port Synchronization Pin. This pin is D4 for direct FSK, PSK, or ASK data.
If serial mode is invoked via F0 to F3, this pin is used to reset the serial port.
19 D3/SDO I/O Parallel Port Pin/Serial Data Output. This pin is D3 for direct FSK, PSK, or ASK data. If serial
mode is invoked via F0 to F3, this pin is used for readback mode for serial operation.
20 D2/SDIO/WR I/O Parallel Port Pin/Serial Data Input and Output/Write Input. This pin is D2 for direct FSK, PSK,
or ASK data. If serial mode is invoked via F0 to F3, this pin is used for the SDIO for serial
operation. If parallel mode is enabled, this pin is used to write to change the values of the
internal registers.
21 D1/SCLK/RD I Parallel Port Pin/Serial Clock/Read Input. This pin is D1 for direct FSK, PSK, or ASK data. If
serial mode is invoked via F0 to F3, this pin is used for SCLK for serial operation. If parallel
mode is enabled, this pin is used to read back the value of the internal registers.
22 D0/CS/PWD I Parallel Port Pin/Chip Select/Parallel Width. This pin is D0 for direct FSK, PSK, or ASK data. If
serial mode is invoked via F0 to F3, this pin is used for the chip select for serial operation. If
parallel mode is enabled, this pin is used to set either 8-bit data or16-bit data.
6, 23, 73 DVDD (1.8V) I Digital Core Supplies (1.8 V).
7, 17, 24, 74, 84 DGND I Digital Ground.
16, 83 DVDD_I/O (3.3V) I Digital Input/Output Supplies (3.3 V).
32, 56, 57 AVDD (1.8V) I Analog Core Supplies (1.8 V).
33, 35, 37, 38,
44, 46, 49, 51
AGND
I
Analog Ground.
34, 36, 39, 40,
43, 47, 50, 52,
53, 60
AVDD (3.3V) I Analog DAC Supplies (3.3 V).
25, 26, 27 PS0 to PS2 I Profile Select Pins. Digital inputs (active high). Use these pins to select one of eight
phase/frequency profiles for the DDS. Changing the state of one of these pins transfers the
current contents of all I/O buffers to the corresponding registers. State changes should be set
up on the SYNC_CLK pin (Pin 82).
28, 29, 30, 31 F0 to F3 I Function Pins. Digital inputs. The state of these pins determines if a serial or parallel interface
is used. In addition, the function pins determine how the 32-bit parallel data-word is
partitioned for FSK, PSK, or ASK modulation mode.
41 AOUT O DAC Complementary Output Source. Analog output (voltage mode). Internally connected
through a 50 Ω resistor to AVDD (3.3V).
42 AOUT O DAC Output Source. Analog output (voltage mode). Internally connected through a 50 Ω
resistor to AVDD (3.3V).
45 DAC_BP I DAC Bypass Pin. Provides access to the common control node of the DAC current sources.
Connecting a capacitor between this pin and ground can improve noise performance at the
DAC output.
48 DAC_RSET O Analog Reference. This pin programs the DAC output full-scale reference current. Connect a
3.3 kΩ resistor to AGND.
54 REF_CLK I Complementary Reference Clock Input. Analog input.
55 REF_CLK I Reference Clock Input. Analog input.
58 LOOP_FILTER O External PLL Loop Filter Node.
59 REF O Local PLL Reference Supply. Typically at 2.05 V.
61 SYNC_OUT O Digital Synchronization Output. Used to synchronize multiple chips.
62 SYNC_IN I Digital Synchronization Input. Used to synchronize multiple chips.
63 DRCTL I Ramp Control. Digital input (active high). This pin controls the sweep direction (up/down).
64
DRHOLD
I
Ramp Hold. Digital input (active high). Pauses the sweep when active.
65 DROVER O Ramp Over. Digital output (active high). This pin switches to Logic 1 when the digital ramp
generator reaches its programmed upper or lower limit.
66 OSK I Output Shift Keying. Digital input (active high). When the OSK features are placed in either
manual or automatic mode, this pin controls the OSK function. In manual mode, it toggles
the multiplier between 0 (low) and the programmed amplitude scale factor (high). In
automatic mode, a low sweeps the amplitude down to zero and a high sweeps the
amplitude up to the amplitude scale factor.
Data Sheet AD9914
Rev. D | Page 11 of 48
Pin No. Mnemonic I/O1 Description
67 EXT_PWR_DWN I External Power-Down. Digital input (active high). A high level on this pin initiates the
currently programmed power-down mode.
82 SYNC_CLK O Clock Output. Digital output. Many of the digital inputs on the chip, such as I/O_UPDATE,
PS[2:0], and the parallel data port (D0 to D31), must be set up on the rising edge of
this signal.
85 MASTER_RESET I Master Reset. Digital input (active high). Clears all memory elements and sets registers to
default values.
86 I/O_UPDATE I Input/Output Update. Digital input (active high). A high on this pin transfers the contents of
the I/O buffers to the corresponding internal registers.
EPAD Exposed Pad. The EPAD must be soldered to ground.
1 I = input, O = output.
AD9914 Data Sheet
Rev. D | Page 12 of 48
TYPICAL PERFORMANCE CHARACTERISTICS
Nominal supply voltage; DAC RSET = 3.3 kΩ, TA = 25°C, unless otherwise noted.
Figure 4. Wideband SFDR at 171.5 MHz
SYSCLK = 3.5 GHz (SYSCLK PLL Bypassed)
Figure 5. Wideband SFDR at 427.5 MHz
SYSCLK = 3.5 GHz (SYSCLK PLL Bypassed)
Figure 6. Wideband SFDR at 696.5 MHz,
SYSCLK = 3.5 GHz (SYSCLK PLL Bypassed)
Figure 7. Narrow-Band SFDR at 171.5 MHz,
SYSCLK = 3.5 GHz (SYSCLK PLL Bypassed)
Figure 8. Narrow-Band SFDR at 427.5 MHz,
SYSCLK = 3.5 GHz (SYSCLK PLL Bypassed)
Figure 9. Narrow-Band SFDR at 696.5 MHz,
SYSCLK = 3.5 GHz (SYSCLK PLL Bypassed)
ST ART 0Hz
–100
–90
–80
–70
–60
–50
–40
–30
–20
–10
0
175MHz/DIV S TO P 1.75GHz
SF DR ( dBc)
10836-004
ST ART 0Hz
–100
–90
–80
–70
–60
–50
–40
–30
–20
–10
0
175MHz/DIV S TO P 1.75GHz
SF DR ( dBc)
10836-005
ST ART 0Hz
–100
–90
–80
–70
–60
–50
–40
–30
–20
–10
0
175MHz/DIV S TO P 1.75GHz
SF DR ( dBc)
10836-006
CENT E R 171.5MHz
–100
–90
–80
–70
–60
–50
–40
–30
–20
–10
0
50kHz/DIV SP AN 500kHz
SF DR ( dBc)
10836-007
CENT E R 427.5MHz
–100
–90
–80
–70
–60
–50
–40
–30
–20
–10
0
50kHz/DIV SP AN 500kHz
SF DR ( dBc)
10836-008
CENT E R 696.5MHz
–100
–90
–80
–70
–60
–50
–40
–30
–20
–10
0
50kHz/DIV SP AN 500kHz
SF DR ( dBc)
10836-009
Data Sheet AD9914
Rev. D | Page 13 of 48
Figure 10. Wideband SFDR at 1396.5 MHz,
SYSCLK = 3.5 GHz (SYSCLK PLL Bypassed)
Figure 11. Wideband SFDR vs. Normalized fOUT
SYSCLK = 3.5 GHz
Figure 12. Wideband SFDR vs. Normalized fOUT,
SYSCLK = 2.5 GHz to 3.5 GHz
Figure 13. Narrow-Band SFDR at 1396.5 MHz,
SYSCLK = 3.5 GHz (SYSCLK PLL Bypassed)
Figure 14. Absolute Phase Noise of REF CLK Source Driving AD9914
Rohde & Schwarz SMA100 Signal Generator at 3.5 GHz Buffered by Series
ADCLK925
Figure 15. Absolute Phase Noise Curves of DDS Output at 3.5 GHz Operation
–100
–90
–80
–70
–60
–50
–40
–30
–20
–10
0
SF DR (d Bc)
ST ART 0Hz 175MHz /DI V ST O P 1.75G H z
10836-010
0
–80 0 0.050.100.15 0.400.350.300.250.20
SF DR (d Bc)
f
C
/
f
S
–70
–60
–50
–40
–30
–20
–10
10836-011
0
–80 0 0.05 0.10 0.15 0.400.350.300.250.20
SF DR (d Bc)
f
C
/
f
S
–70
–60
–50
–40
–30
–20
–10
10836-012
SYSCLK = 2.7GHz
SYSCLK = 2.8GHz
SYSCLK = 2.9GHz
SYSCLK = 3.0GHz
SYSCLK = 3.1GHz
SYSCLK = 3.2GHz
SYSCLK = 3.3GHz
SYSCLK = 3.4GHz
SYSCLK = 3.5GHz
SYSCL K = 1.5GHz
SYSCL K = 1.6GHz
SYSCL K = 1.7GHz
SYSCL K = 1.8GHz
SYSCL K = 1.9GHz
SYSCL K = 2.0GHz
SYSCL K = 2.1GHz
SYSCL K = 2.2GHz
SYSCL K = 2.3GHz
SYSCL K = 2.4GHz
SYSCL K = 2.5GHz
SYSCL K = 2.6GHz
CENT ER 1396.5M Hz
–100
–90
–80
–70
–60
–50
–40
–30
–20
–10
0
50kHz/DIV SPAN 500kHz
SFDR (dBc)
10836-013
10 100 1k 10k 100k 1M 10M 100M
FREQUENCY OFF SET (Hz)
70
–90
–80
–100
–110
–120
–130
–140
–150
–160
–170
PHASE NOISE (dBc/Hz)
SMA
SMA AND
ADCLK925
10836-014
10 100 1k 10k 100k 1M 10M 100M
FREQUENCY OFF SET (Hz)
70
–90
–80
–100
–110
–120
–130
–140
–150
–160
–170
PHASE NOISE (dBc/Hz)
1396MHz
696MHz
427MHz 171MHz
10836-015
AD9914 Data Sheet
Rev. D | Page 14 of 48
Figure 16. Absolute Phase Noise Curves of Normalized REF CLK Source to
DDS Output at 1396 MHz (SYSCLK = 3.5 GHz)
Figure 17. Residual Phase Noise Curves
Figure 18. Power Supply Current vs. SYSCLK
Figure 19. Absolute Phase Noise Curves of DDS Output Using Internal PLL at
2.5 GHz Operation
Figure 20. Residual PN vs. Absolute PN Measurement Curves at 1396 MHz
Figure 21. Residual Phase Noise vs. Normalized Absolute REF CLK Source
Phase Noise at 1396 MHz
10 100 1k 10k 100k 1M 10M 100M
FREQUENCY OFFSET (Hz)
70
–90
–80
–100
–110
–120
–130
–140
–150
–160
–170
PHASE NOISE (dBc/Hz)
1396MHz
NORMALIZED
REF CLK S O URCE
10836-016
60
–90
–80
–70
–100
–110
–120
–130
–140
–150
–160
–170
–180
10836-017
10 100 1k 10k 100k 1M 10M 100M
FREQUENCY OFFSET (Hz)
PHASE NOISE (d Bc/Hz)
427MHz
1396MHz
696MHz
171MHz
0.5
0.4
0.3
0.2
0.1
0
500 1000 400035003000250020001500
SUPPLY CURRENT (A)
SYSTEM CLOCK (MHz)
10836-018
3.3V ANALOG
3.3V DI GITAL
1.8V ANALOG
1.8V DI GITAL
10 100 1k 10k 100k 1M 10M 100M
FREQUENCY OFFSET (Hz)
70
–90
–80
–100
–110
–120
–130
–140
–150
–160
–170
PHASE NOISE (dBc/Hz)
978MHz
305MHz
123MHz
497MHz
10836-019
10 100 1k 10k 100k 1M 10M 100M
FR E QUENC Y OFFSE T ( Hz )
PHASE NOISE (dBc/Hz)
1396MHz ABSOLUTE
1396MHz RESIDUAL
60
–90
–80
–70
–100
–110
–120
–130
–140
–150
–160
10836-020
60
–90
–80
–70
–100
–110
–120
–130
–140
–150
–160
–170
–18010 100 1k 10k 100k 1M 10M 100M
FREQUENCY OFFSET (Hz)
PHASE NOISE (d Bc/Hz)
1396MHz ABSOLUTE
1396MHz RESIDUAL
10836-021
Data Sheet AD9914
Rev. D | Page 15 of 48
Figure 22. SYNC_OUT (fSYSCLK/384)
Figure 23. DAC Calibration Time vs. SYSCLK Rate. See the DAC Calibration
Output Section for Formula.
Figure 24. Measured Rising Linear Frequency Sweep
Figure 25. Measured Falling Linear Frequency Sweep
10836-022
CH2 1.0V Ω M20.00ms IT 40.0ps/pt
A CH2 1.64V
1
1.0
0.9
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0
500 3500
TIME (ms)
SYSTEM CLOCK RATE (MHz)
1000 1500 2000 2500 3000
10836-023
930
870
880
890
900
910
920
–6 –2–4 6420
FREQUENCY (MHz)
TIME (ms)
10836-024
930
870
880
890
900
910
920
–6 –2–4 6420
FREQUENCY (MHz)
TIME (ms)
10836-025
AD9914 Data Sheet
Rev. D | Page 16 of 48
EQUIVALENT CIRCUITS
Figure 26. DAC Output
Figure 27. REF CLK input
Figure 28. CMOS Input
Figure 29. CMOS Output
10836-044
SWITCH
CONTROL
CODE
AGND
AVDD (3.3V)
CURRENT
SWITCH
ARRAY
CURRENT
SWITCH
ARRAY
AOUT AOUT
INTERNAL
50Ω
INTERNAL
50Ω
I
FS
/2 + I
CODE
I
FS
/2 – I
CODE
I
FS
41
42
10836-048
REF_CLK REF_CLK
AVDD (3.3V)
DVDD (3.3V)
10836-045
DVDD (3.3V)
10836-043
Data Sheet AD9914
Rev. D | Page 17 of 48
THEORY OF OPERATION
The AD9914 has five modes of operation.
Single tone
Profile modulation
Digital ramp modulation (linear sweep)
Parallel data port modulation
Programmable modulus mode
The modes define the data source used to supply the DDS with
its signal control parameters: frequency, phase, or amplitude.
The partitioning of the data into different combinations of
frequency, phase, and amplitude is established based on the
mode and/or specific control bits and function pins.
Although the various modes are described independently, they can
be enabled simultaneously. This provides an unprecedented level
of flexibility for generating complex modulation schemes. However,
to avoid multiple data sources from driving the same DDS signal
control parameter, the device has a built-in priority protocol.
In single tone mode, the DDS signal control parameters come
directly from the profile programming registers. In digital ramp
modulation mode, the DDS signal control parameters are delivered
by a digital ramp generator. In parallel data port modulation mode,
the DDS signal control parameters are driven directly into the
parallel port.
The various modulation modes generally operate on only one of
the DDS signal control parameters (two in the case of the polar
modulation format via the parallel data port). The unmodulated
DDS signal control parameters are stored in programming registers
and automatically routed to the DDS based on the selected mode.
A separate output shift keying (OSK) function is also available.
This function employs a separate digital linear ramp generator
that affects only the amplitude parameter of the DDS. The OSK
function has priority over the other data sources that can drive
the DDS amplitude parameter. As such, no other data source
can drive the DDS amplitude when the OSK function is enabled.
SINGLE TONE MODE
In single tone mode, the DDS signal control parameters are
supplied directly from the profile programming registers. A
profile is an independent register that contains the DDS signal
control parameters. Eight profile registers are available. Note
that the profile pins must be used to select the desired register.
PROFILE MODULATION MODE
Each profile is independently accessible. For FSK, PSK, or ASK
modulation, use the three external profile pins (PS[2:0]) to select
the desired profile. A change in the state of the profile pins with
the next rising edge on SYNC_CLK updates the DDS with the
parameters specified by the selected profile. Therefore, the profile
change must meet the setup and hold times to the SYNC_CLK
rising edge. Note that amplitude control must also be enabled
using the OSK enable bit in the CFR1 register (0x00[8]).
DIGITAL RAMP MODULATION MODE
In digital ramp modulation mode, the modulated DDS signal
control parameter is supplied directly from the digital ramp
generator (DRG). The ramp generation parameters are
controlled through the serial or parallel I/O port.
The ramp generation parameters allow the user to control both
the rising and falling slopes of the ramp. The upper and lower
boundaries of the ramp, the step size and step rate of the rising
portion of the ramp, and the step size and step rate of the falling
portion of the ramp are all programmable.
The ramp is digitally generated with 32-bit output resolution.
The 32-bit output of the DRG can be programmed to affect
frequency, phase, or amplitude. When programmed for frequency,
all 32 bits are used. However, when programmed for phase or
amplitude, only the 16 MSBs or 12 MSBs, respectively, are used.
The ramp direction (rising or falling) is externally controlled by
the DRCTL pin. An additional pin (DRHOLD) allows the user
to suspend the ramp generator in its present state. Note that
amplitude control must also be enabled using the OSK enable
bit in Register CFR1.
PARALLEL DATA PORT MODULATION MODE
In parallel data port modulation mode, the modulated DDS signal
control parameter(s) are supplied directly from the 32-bit parallel
data port. The function pins define how the 32-bit data-word is
applied to the DDS signal control parameters. Formatting of the
32-bit data-word is unsigned binary, regardless of the destination.
Parallel Data Clock (SYNC_CLK)
The AD9914 generates a clock signal on the SYNC_CLK pin
that runs at 1/24 of the DAC sample rate (the sample rate of the
parallel data port). SYNC_CLK serves as a data clock for the
parallel port.
PROGRAMMABLE MODULUS MODE
In programmable modulus mode, the DRG is used as an
auxiliary accumulator to alter the frequency equation of the
DDS core, making it possible to implement fractions that are
not restricted to a power of 2 in the denominator. A standard
DDS is restricted to powers of 2 as a denominator because the
phase accumulator is a set of bits as wide as the frequency
tuning word (FTW).
When in programmable modulus mode, however, the
frequency equation is:
f0 = (fS)(FTW + A/B)/232
where f0/fS < ½, 0 ≤ FTW < 231, 2 ≤ B ≤ 2321, and A < B.
This equation implies a modulus of B × 232 (rather than 232, in
the case of a standard DDS). Furthermore, because B is
programmable, the result is a DDS with a programmable
modulus.
AD9914 Data Sheet
Rev. D | Page 18 of 48
When in programmable modulus mode, the 32-bit auxiliary
accumulator operates in a way that allows it to roll over at a
value other than its full capacity of 232. That is, it operates with a
modified modulus based on the programmable value of B. With
each roll over of the auxiliary accumulator, a value of 1 LSB
adds to the current accumulated value of the 32-bit phase
accumulator. This behavior changes the modulus of the phase
accumulator to B × 232 (instead of 232), allowing it to synthesize
the desired f0.
To determine the programmable modulus mode register values
for FTW, A, and B, the user must first define f0/fS as a ratio of
relatively prime integers, M/N. That is, having converted f0 and
fS to integers, M and N, reduce the fraction, M/N, to its lowest
terms. Then, divide M × 232 by N. The integer part of this division
operation is the value of FTW (Register 0x04[31:0]). The
remainder, Y, of this division operation is
Y = (232 × M) – (FTW × N)
The value of Y facilitates the determination of A and B by taking
the fraction, Y/N, and reducing it to its lowest terms. Then, the
numerator of the reduced fraction is A (Register 0x06[31:0])
and the denominator is the B (Register 0x05[31:0]).
For example, synthesizing precisely 300 MHz with a 1 GHz
system clock is not possible with a standard DDS. It is possible,
however, using programmable modulus as follows.
First, express f0/fS as a ratio of integers:
300,000,000/1,000,000,000
Reducing this fraction to lowest terms yields 3/10; therefore,
M = 3 and N = 10. FTW is the integer part of (M × 232)/N, or
(3 × 232)/10, which is 1,288,490,188 (0x4CCCCCCC in 32-bit
hexadecimal notation). The remainder, Y, of (3 × 232)/10, is (232
× 3) (1,288,490,188 × 10), which is 8. Therefore, Y/N is 8/10,
which reduces to 4/5. Therefore, A = 4 and B = 5 (0x00000004
and 0x00000005 in 32-bit hexadecimal notation, respectively).
Programming the AD9914 with these values of FTW, A, and B
results in an output frequency that is exactly 3/10 of the system
clock frequency.
MODE PRIORITY
The ability to activate each mode independently makes it
possible to have multiple data sources attempting to drive the
same DDS signal control parameter (frequency, phase, and
amplitude). To avoid contention, the AD9914 has a built-in
priority system. Table 6 summarizes the priority for each of the
DDS modes. The data source column in Table 6 lists data sources
for a particular DDS signal control parameter in descending
order of precedence. For example, if the profile mode enable bit
and the parallel data port enable bit (0x01[23:22]) are set to
Logic 1 and both are programmed to source the frequency
tuning word to DDS output, the profile modulation mode has
priority over the parallel data port modulation mode.
Table 6. Data Source Priority
Priority
DDS Signal Control Parameters
Data Source Conditions
Highest
Priority
Programmable
modulus
If programmable modulus mode is used to output frequency only, no other data source can be used to
control the output frequency in this mode. Note that the DRG is used in conjunction with programmable
modulus mode; therefore, the DRG cannot be used to sweep phase or amplitude in programmable
modulus mode.
If output phase offset control is desired, enable profile mode and use the profile registers and profile
pins accordingly to control output phase adjustment.
If output amplitude control is desired, enable profile mode and use the profile registers and profile pins
accordingly to control output amplitude adjustment. Note that the OSK enable bit must be set to control
the output amplitude.
DRG The digital ramp modulation mode is the next highest priority mode. If the DRG is enabled to sweep
output frequency, phase, or amplitude, the two parameters not being swept can be controlled
independently via the profile mode.
Profiles The profile modulation mode is the next highest priority mode. Profile mode can be used to control all
three parameters independently, if desired.
Lowest
Priority
Parallel port Parallel data port modulation has the lowest priority but the most flexibility as far as changing any
parameter at the high rate. See the Programming and Function Pins section.
Data Sheet AD9914
Rev. D | Page 19 of 48
FUNCTIONAL BLOCK DETAIL
DDS CORE
The direct digital synthesizer (DDS) block generates a reference
signal (sine or cosine based on 0x00[16], the enable sine output
bit). The parameters of the reference signal (frequency, phase,
and amplitude) are applied to the DDS at its frequency, phase
offset, and amplitude control inputs, as shown in Figure 30.
The output frequency (fOUT) of the AD9914 is controlled by the
frequency tuning word (FTW) at the frequency control input to
the DDS. The relationship among fOUT, FTW, and fSYSCLK is given by
SYSCLK
OUT
f
FTW
f
=
32
2
(1)
where FTW is a 32-bit integer ranging in value from 0 to
2,147,483,647 (231 − 1), which represents the lower half of the
full 32-bit range. This range constitutes frequencies from dc to
Nyquist (that is, ½ fSYSCLK).
The FTW required to generate a desired value of fOUT is found
by solving Equation 1 for FTW, as given in Equation 2.
=
SYSCLK
OUT
f
f
FTW
32
2round
(2)
where the round(x) function rounds the argument (the value of
x) to the nearest integer. This is required because the FTW is
constrained to be an integer value. For example, for fOUT =
41 MHz and fSYSCLK = 122.88 MHz, FTW = 1,433,053,867
(0x556AAAAB).
Programming an FTW greater than 231 produces an aliased
image that appears at a frequency given by
SYSCLK
OUT f
FTW
f
=32
2
1
(for FTW ≥ 231)
The relative phase of the DDS signal can be digitally controlled
by means of a 16-bit phase offset word (POW). The phase offset
is applied prior to the angle-to-amplitude conversion block internal
to the DDS core. The relative phase offset θ) is given by
=
14
14
2
360
2
2
POW
POW
π
θ
where the upper quantity is for the phase offset expressed as
radian units and the lower quantity as degrees.
To find the POW value necessary to develop an arbitrary Δθ,
solve the preceding equation for POW and round the result (in
a manner similar to that described previously for finding an
arbitrary FTW).
The relative amplitude of the DDS signal can be digitally scaled
(relative to full scale) by means of a 12-bit amplitude scale factor
(ASF). The amplitude scale value is applied at the output of the
angle-to-amplitude conversion block internal to the DDS core.
The amplitude scale is given by
=
12
12
2
log20
2
ASF
ASF
ScaleAmplitude
(3)
where the upper quantity is amplitude expressed as a fraction of
full scale and the lower quantity is expressed in decibels relative
to full scale.
To find the ASF value necessary for a particular scale factor, solve
Equation 3 for ASF and round the result (in a manner similar
to that described previously for finding an arbitrary FTW).
When the AD9914 is programmed to modulate any of the DDS
signal control parameters, the maximum modulation sample
rate is 1/24 fSYSCLK. This means that the modulation signal exhibits
images at multiples of 1/24 fSYSCLK. The impact of these images
must be considered when using the device as a modulator.
Figure 30. DDS Block Diagram
DDS_CLK
32 17
FREQUENCY
CONTROL
ANGLE-TO-
AMPLITUDE
CONVERSION
(SINE OR
COSINE)
PHASE
OFFSET
CONTROL
TO DAC
(MSBs)
D Q
R
ACCUMULATOR
RESET
32
16
MSB ALIGNED
AMPLITUDE
CONTROL 12
DDS SIGNA L CO NTROL PARAMETERS
14
12
17
32
32 12
12
32-BIT
ACCUMULATOR
10836-026
AD9914 Data Sheet
Rev. D | Page 20 of 48
12-BIT DAC OUTPUT
The AD9914 incorporates an integrated 12-bit, current output
DAC. The output current is delivered as a balanced signal using
two outputs. The use of balanced outputs reduces the potential
amount of common-mode noise present at the DAC output,
offering the advantage of an increased signal-to-noise ratio. An
external resistor (RSET) connected between the DAC_RSET pin
and AGND establishes the reference current. The recommended
value of RSET is 3.3 kΩ.
Attention should be paid to the load termination to keep the
output voltage within the specified compliance range; voltages
developed beyond this range cause excessive distortion and can
damage the DAC output circuitry.
DAC CALIBRATION OUTPUT
The DAC CAL enable bit in the CFR4 control register (0x03[24])
must be manually set and then cleared after each power-up and
every time the REF CLK or internal system clock is changed.
This initiates an internal calibration routine to optimize the
setup and hold times for internal DAC timing. Failure to
calibrate may degrade performance and even result in loss of
functionality. The length of time to calibrate the DAC clock is
calculated from the following equation:
S
CAL f
t632,469
=
RECONSTRUCTION FILTER
The DAC output signal appears as a sinusoid sampled at fS. The
frequency of the sinusoid is determined by the frequency tuning
word (FTW) that appears at the input to the DDS. The DAC
output is typically passed through an external reconstruction
filter that serves to remove the artifacts of the sampling process
and other spurs outside the filter bandwidth.
Because the DAC constitutes a sampled system, its output must
be filtered so that the analog waveform accurately represents the
digital samples supplied to the DAC input. The unfiltered DAC
output contains the desired baseband signal, which extends from
dc to the Nyquist frequency (fS/2). It also contains images of the
baseband signal that theoretically extend to infinity. Notice that
the odd numbered images (shown in Figure 31) are mirror
images of the baseband signal. Furthermore, the entire DAC
output spectrum is affected by a sin(x)/x response, which is
caused by the sample-and-hold nature of the DAC output signal.
For applications using the fundamental frequency of the DAC
output, the response of the reconstruction filter should preserve
the baseband signal (Image 0), while completely rejecting all
other images. However, a practical filter implementation
typically exhibits a relatively flat pass band that covers the
desired output frequency plus 20%, rolls off as steeply as
possible, and then maintains significant (though not complete)
rejection of the remaining images. Depending on how close
unwanted spurs are to the desired signal, a third-, fifth-, or
seventh-order elliptic low-pass filter is common.
Some applications operate from an image above the Nyquist
frequency, and those applications use a band-pass filter instead
of a low-pass filter. The design of the reconstruction filter has a
significant impact on the overall signal performance. Therefore,
good filter design and implementation techniques are important
for obtaining the best possible jitter results.
Figure 31. DAC Spectrum vs. Reconstruction Filter Response
PRIMARY
SIGNAL FILTER
RESPONSE SIN(x)/x
ENVELOPE
SPURS
IMAGE 0 IMAGE 1 IMAGE 2 IMAGE 3 IMAGE 4
0
–20
–40
–60
–80
–100
MAGNITUDE
(dB)
fs/2 fs3fs/2 2fs5fs/2
f
BASE BAND
10836-027
Data Sheet AD9914
Rev. D | Page 21 of 48
CLOCK INPUT (REF_CLK/REF_CLK)
REF_CLK/REF_CLK Overview
The AD9914 supports a number of options for producing the
internal SYSCLK signal (that is, the DAC sample clock) via the
REF_CLK/REF_CLK input pins. The REF_CLK input can be
driven directly from a differential or single-ended source. There
is also an internal phase-locked loop (PLL) multiplier that can
be independently enabled. However, the PLL limits the SYSCLK
signal between 2.4 GHz and 2.5 GHz operation. A differential
signal is recommended when the PLL is bypassed. A block
diagram of the REF_CLK functionality is shown in Figure 32.
Figure 32 also shows how the CFR3 control bits are associated
with specific functional blocks.
Figure 32. REF_CLK Block Diagram
The PLL enable bit is used to choose between the PLL path or
the direct input path. When the direct input path is selected,
the REF_CLK/REF_CLK pins must be driven by an external
signal source (single-ended or differential). Input frequencies
up to 3.5 GHz are supported.
Direct Driven REF_CLK/REF_CLK
With a differential signal source, the REF_CLK/REF_CLK pins
are driven with complementary signals and ac-coupled with 0.1 µF
capacitors. With a single-ended signal source, either a single-
ended-to-differential conversion can be employed or the
REF_CLK input can be driven single-ended directly. In either
case, 0.1 µF capacitors are used to ac couple both
REF_CLK/ REF_CLK pins to avoid disturbing the internal dc
bias voltage of ~1.35 V. See Figure 33 for more details.
The REF_CLK/REF_CLK input resistance is ~2.5 kΩ differential
(~1.2 kΩ single-ended). Most signal sources have relatively low
output impedances. The REF_CLK/REF_CLK input resistance
is relatively high; therefore, its effect on the termination impedance
is negligible and can usually be chosen to be the same as the output
impedance of the signal source. The bottom two examples in
Figure 33 assume a signal source with a 50 Ω output impedance.
Figure 33. Direct Connection Diagram
Phase-Locked Loop (PLL) Multiplier
An internal phase-locked loop (PLL) provides the option to use
a reference clock frequency that is significantly lower than the
system clock frequency. The PLL supports a wide range of
programmable even frequency multiplication factors (20× to
510×) as well as a programmable charge pump current and
external loop filter components (connected via the PLL
LOOP_FILTER pin). These features add an extra layer of
flexibility to the PLL, allowing optimization of phase noise
performance and flexibility in frequency plan development. The
PLL is also equipped with a PLL lock bit indicator (0x1B[24]).
The PLL output frequency range (fSYSCLK) is constrained to the
range of 2.4 GHz ≤ fSYSCLK ≤ 2.5 GHz by the internal VCO.
VCO Calibration
When using the PLL to generate the system clock, VCO calibration
is required to tune the VCO appropriately and achieve good
performance. When the reference input signal is stable, the
VCO cal enable bit in the CFR1 register, 0x00[24], must be
asserted. Subsequent VCO calibrations require that the VCO
calibration bit be cleared prior to initiating another VCO
calibration. VCO calibration must occur before DAC calibration
to ensure optimal performance and functionality.
REF_CLK
REF_CLK
2 7
2
LOOP_FILTER
58
DOUBL E R E NABLE
CFR3[19]
55
54
DOUBLER
CLO CK E DGE
CFR3[16]
×2
÷ 1, 2, 4, 8
ENABLE
IN
PLL ENABLE
CFR3[18]
LOOP
FILTER
PLL OUT
0
1
0
1SYSCLK
INPUT DI V IDER
RESET CF R3[ 22]
INPUT DI V IDER RAT IO
CFR3[21:20]
CHARGE
PUMP DIVIDE
N
CFR3[15:8]
I
CP
CFR3[5:3]
10836-028
TERMINATION
REF_CLK
DIFFERENTIAL SOURCE,
DIFFERENTIAL I NP UT
SI NGLE - E NDE D S OURCE,
DIFFERENTIAL I NP UT
SI NGLE - E NDE D S OURCE,
SI NGLE - E NDE D INPUT
55
54
0.1µF
0.1µF
PECL,
LVPECL,
OR
LVDS
DRIVER
REF_CLK
55
54
50Ω
0.1µF
0.1µF
BALUN
(1:1)
REF_CLK
REF_CLK
REF_CLK
REF_CLK
55
54
0.1µF
0.1µF
50Ω
10836-029
AD9914 Data Sheet
Rev. D | Page 22 of 48
PLL Charge Pump/Total Feedback Divider
The charge pump current (ICP) value is automatically chosen via
the VCO calibration process and N value (N = 10 to 255) stored
in Feedback Divider N[7:0] in the CFR3 register (0x02[15:8]). N
values below 10 should be avoided.
Note that the total PLL multiplication value for the PLL is always
2N due to the fixed divide by 2 element in the feedback path.
This is shown in Figure 34. This fixed divide by 2 element forces
only even PLL multiplication.
To manually override the charge pump current value, the manual
ICP selection bit in CFR3 (0x02[6]) must be set to Logic 1. This
provides the user with additional flexibility to optimize the PLL
performance. Table 7 lists the bit settings vs. the nominal charge
pump current.
Table 7. PLL Charge Pump Current
ICP Bits (CFR3[5:3]) Charge Pump Current, ICP A)
000 125
001 250
010 375
011
500 (default)
100 625
101 750
110 875
111 1000
Table 8. N divider vs. Charge Pump Current
N Divider Range
Recommended Charge Pump
Current, ICP A)
10 to 15 125
16 to 23 250
24 to 35 375
36 to 43 500
44 to 55 625
56 to 63 750
64 to 79 875
80 to 100 1000
PLL Loop Filter Components
The loop filter is mostly internal to the device, as shown in
Figure 34. The recommended external capacitor value is 560 pF.
Because CP and RPZ are integrated, it is not recommended to
adjust the loop bandwidth via the external capacitor value. The
better option is to adjust the charge pump current even though
it is a coarse adjustment.
For example, suppose the PLL is manually programmed such
that ICP = 375 μA, KV = 60 MHz/V, and N = 25. This produces a
loop bandwidth of approximately 250 kHz.
Figure 34. REF CLK PLL External Loop Filter
PLL LOCK INDICATION
When the PLL is in use, the PLL lock bit (0x1B[24])provides an
active high indication that the PLL has locked to the REF CLK
input signal.
OUTPUT SHIFT KEYING (OSK)
The OSK function (see Figure 35) allows the user to control the
output signal amplitude of the DDS. The amplitude data generated
by the OSK block has priority over any other functional block
that is programmed to deliver amplitude data to the DDS.
Therefore, the OSK data source, when enabled, overrides all
other amplitude data sources.
The operation of the OSK function is governed by two CFR1
register bits, OSK enable (0x00[8]) and external OSK enable
(0x00[9]), the external OSK pin, the profile pins, and the 12 bits
of amplitude scale factor found in one of eight profile registers.
The profile pins are used to select the profile register containing
the desired amplitude scale factor.
The primary control for the OSK block is the OSK enable bit
(0x00[8]). When the OSK function is disabled, the OSK input
controls and OSK pin are ignored.
The OSK pin functionality depends on the state of the external
OSK enable bit and the OSK enable bit. When both bits are set
to Logic 1 and the OSK pin is Logic 0, the output amplitude is
forced to 0; otherwise, if the OSK pin is Logic 1, the output
amplitude is set by the amplitude scale factor value in one of
eight profile registers depending on the profile pin selection.
Figure 35. OSK Block Diagram
PFD CP
LOOP_FILTER
VCO
÷N ÷2
PLL OUT
PLL IN
REF CLK PL L
R
PZ
(3.5kΩ)
C
Z
= 560pF (RE COMM E NDE D)
59 58
10836-030
REF
0.47µF
C
P
50pF
OS K E NABLE
EXTERNAL
OS K E NABLE
12
OSK
DDS CL OCK
12
PS0 PS1 PS2
25 26 27 66
TO DDS
AMPLITUDE
CONTROL
PARAMETER
OSK
CONTROLLER
AMPLITUDE S CALE
FACTOR (1 OF 8
SELECTED PROFILE
REGISTERS [27:16])
10836-031
Data Sheet AD9914
Rev. D | Page 23 of 48
DIGITAL RAMP GENERATOR (DRG)
DRG Overview
To sweep phase, frequency, or amplitude from a defined start
point to a defined endpoint, a completely digital ramp generator
is included in the AD9914. The DRG makes use of eight control
register bits, three external pins, and five 32-bit registers (see
Figure 36).
Figure 36. Digital Ramp Block Diagram
The primary control for the DRG is the digital ramp enable bit
(0x01[19]). When disabled, the other DRG input controls are
ignored and the internal clocks are shut down to conserve power.
The output of the DRG is a 32-bit unsigned data bus that can be
routed to any one of the three DDS signal control parameters, as
controlled by the two digital ramp destination bits in Control
Function Register 2 according to Table 9. The 32-bit output bus
is MSB-aligned with the 32-bit frequency parameter, the 16-bit
phase parameter, or the 12-bit amplitude parameter, as defined
by the destination bits. When the destination is phase or amplitude,
the unused LSBs are ignored.
Table 9. Digital Ramp Destination
Digital Ramp
Destination Bits
(CFR2[21:20])
DDS Signal
Control
Parameter
Bits Assigned to
DDS Parameter
00
Frequency
31:0
01 Phase 31:18
1x1 Amplitude 31:20
1 x = don’t care.
The ramp characteristics of the DRG are fully programmable. This
includes the upper and lower ramp limits, and independent control
of the step size and step rate for both the positive and negative slope
characteristics of the ramp. A detailed block diagram of the DRG is
shown in Figure 37.
The direction of the ramping function is controlled by the
DRCTL pin. Logic 0 on this pin causes the DRG to ramp with a
negative slope, whereas Logic 1 causes the DRG to ramp with a
positive slope.
The DRG also supports a hold feature controlled via the DRHOLD
pin. When this pin is set to Logic 1, the DRG is stalled at its last
state; otherwise, the DRG operates normally. The DDS signal
control parameters that are not the destination of the DRG are
taken from the active profile.
Figure 37. Digital Ramp Generator Detail
DRCTL
DDS CL OCK
DRHOLD
DROVER
DIGITAL RAMP ENABL E
LOAD LRR AT I/O_UPDATE
CLE AR DIGI TAL
RAMPACCUMULATOR
AUTOCLEAR DIGITAL
RAMPACCUMULATOR 32
32
DIGITAL RAMP DESTINATION 2
DIGITAL RAMP NO- DWELL2
32
32
63 64 65
32
32
TO DDS
SIGNAL
CONTROL
PARAMETER
DIGITAL
RAMP
GENERATOR
DIGITAL RAMP LOWER LIMIT REGISTER
RISING DIGITAL RAMP STEP
SIZE REGI ST ER
DIGITAL RAMP UPPER LIMIT REGISTER
FALLING DIGITAL RAMP STEP
SIZE REGI ST ER
DIGITAL RAMP RATE REGISTER
10836-032
DDS CL OCK
D Q
R
LOWER
LIMIT
0
1
DECREMENT ST E P SIZE
PRESET
Q
DRCTL
LOAD
CLE AR DIGITAL RAMPACCUMULATOR
AUTO CLEAR DI GITAL RAMPACC
.
NO DWELL
LIMIT CONTROL
DIGITAL RAMPACCUMULATOR
INCRE M E NT ST E P SIZE
32
32
0
1
NEGAT I VE SL O PE RATE
POSIT I VE SL O PE RATE
16
16
32
16
63
DRHOLD 64
32
32
LOAD
CONTROL
LOGIC
LOAD LRR AT I/O_UPDATE
DIGITAL
RAMP
TIMER
ACCUMULATOR
RESET
CONTROL
LOGIC
NO-DWELL
CONTROL2
3232
TO DDS
SIGNAL
CONTROL
PARAMETER
UPPER
LIMIT
32
10836-033
AD9914 Data Sheet
Rev. D | Page 24 of 48
DRG Slope Control
The core of the DRG is a 32-bit accumulator clocked by a
programmable timer. The time base for the timer is the DDS
clock, which operates at 1/24 fSYSCLK. The timer establishes the
interval between successive updates of the accumulator. The
positive (+Δt) and negative (−Δt) slope step intervals are
independently programmable as given by
SYSCLK
f
P
t24
=+
SYSCLK
f
N
t24
=
where P and N are the two 16-bit values stored in the 32-bit digital
ramp rate register and control the step interval. N defines the step
interval of the negative slope portion of the ramp. P defines the step
interval of the positive slope portion of the ramp.
The step size of the positive (STEPP) and negative (STEPN) slope
portions of the ramp are 32-bit values programmed into the 32-bit
rising and falling digital ramp step size registers (0x06 and 0x07).
Program each of the step sizes as an unsigned integer (the hardware
automatically interprets STEPN as a negative value). The
relationship between the 32-bit step size values and actual units
of frequency, phase, or amplitude depend on the digital ramp
destination bits. Calculate the actual frequency, phase, or amplitude
step size by substituting STEPN or STEPP for M in the following
equations as required:
SYSCLK
f
M
StepFrequency
=
32
2
31
2
M
StepPhase
π
=
(radians)
29
2
45M
StepPhase =
(degrees)
FS
I
M
StepAmplitude
=
32
2
Note that the frequency units are the same as those used to
represent fSYSCLK (MHz, for example). The amplitude units are
the same as those used to represent IFS, the full-scale output
current of the DAC (mA, for example).
The phase and amplitude step size equations yield the average
step size. Although the step size accumulates with 32-bit precision,
the phase or amplitude destination exhibits only 16 bits or 12 bits,
respectively. Therefore, at the destination, the actual phase or
amplitude step is the accumulated 32-bit value truncated to
16 bits or 12 bits, respectively.
As described previously, the step interval is controlled by a
16-bit programmable timer. There are three events that can
cause this timer to be reloaded prior to its expiration. One event
occurs when the digital ramp enable bit transitions from cleared
to set, followed by an I/O update. A second event is a change of
state in the DRCTL pin. The third event is enabled using the load
LRR at I/O update bit (0x00[15]).
DRG Limit Control
The ramp accumulator is followed by limit control logic that
enforces an upper and lower boundary on the output of the
ramp generator. Under no circumstances does the output of the
DRG exceed the programmed limit values while the DRG is
enabled. The limits are set through the 64-bit digital ramp limit
register. Note that the upper limit value must be greater than the
lower limit value to ensure normal operation.
DRG Accumulator Clear
The ramp accumulator can be cleared (that is, reset to 0) under
program control. When the ramp accumulator is cleared, it forces
the DRG output to the lower limit programmed into the digital
ramp limit register.
With the limit control block embedded in the feedback path of the
accumulator, resetting the accumulator is equivalent to presetting
it to the lower limit value.
Data Sheet AD9914
Rev. D | Page 25 of 48
Figure 38. Normal Ramp Generation
Normal Ramp Generation
Normal ramp generation implies that both no-dwell bits are
cleared (see the No-Dwell Ramp Generation section for details).
In Figure 38, a sample ramp waveform is depicted with the
required control signals. The top trace is the DRG output. The
next trace down is the status of the DROVER output pin (assuming
that the DRG over output enable bit is set). The remaining traces
are control bits and control pins. The pertinent ramp parameters
are also identified (upper and lower limits plus step size and Δt
for the positive and negative slopes). Along the bottom, circled
numbers identify specific events. These events are referred to by
number (Event 1 and so on) in the following paragraphs.
In this example, the positive and negative slopes of the ramp are
different to demonstrate the flexibility of the DRG. The parameters
of both slopes can be programmed to make the positive and
negative slopes the same.
Event 1The digital ramp enable bit is set, which has no effect
on the DRG output because the bit is not effective until an I/O
update occurs.
Event 2An I/O update registers the digital ramp enable bit. If
DRCTL = 1 is in effect (the gray portion of the DRCTL trace),
the DRG output immediately begins a positive slope (the gray
portion of the DRG output trace). Otherwise, if DRCTL = 0, the
DRG output is initialized to the lower limit.
Event 3DRCTL transitions to Logic 1 to initiate a positive
slope at the DRG output. In this example, the DRCTL pin is
held long enough to cause the DRG to reach its programmed
upper limit. The DRG remains at the upper limit until the ramp
accumulator is cleared (DRCTL = 0) or the upper limit is
reprogrammed to a higher value. In the latter case, the DRG
immediately resumes its previous positive slope profile.
Event 4DRCTL transitions to Logic 0 to initiate a negative
slope at the DRG output. In this example, the DRCTL pin is
held long enough to cause the DRG to reach its programmed
lower limit. The DRG remains at the lower limit until DRCTL = 1,
or until the lower limit is reprogrammed to a lower value. In the
latter case, the DRG immediately resumes its previous negative
slope profile.
Event 5DRCTL transitions to Logic 1 for the second time,
initiating a second positive slope.
Event 6The positive slope profile is interrupted by DRHOLD
transitioning to Logic 1. This stalls the ramp accumulator and
freezes the DRG output at its last value.
Event 7DRHOLD transitions to Logic 0, releasing the ramp
accumulator and reinstating the previous positive slope profile.
Event 8The clear digital ramp accumulator bit is set, which
has no effect on the DRG because the bit is not effective until an
I/O update is issued.
Event 9An I/O update registers that the clear digital ramp
accumulator bit is set, resetting the ramp accumulator and forcing
the DRG output to the programmed lower limit. The DRG output
remains at the lower limit until the clear condition is removed.
Event 10The clear digital ramp accumulator bit is cleared,
which has no effect on the DRG output because the bit is not
effective until an I/O update is issued.
Event 11An I/O update registers that the clear digital ramp
accumulator bit is cleared, releasing the ramp accumulator; and
the previous positive slope profile restarts.
Event 12The autoclear digital ramp accumulator bit is set,
which has no effect on the DRG output because the bit is not
effective until an I/O update is issued.
DRG OUTP UT
LOWER LIMIT
UPPER LIMIT
DRCTL
DRHOLD
AUTOCLEAR DIGITAL
RAMPACCUMULATOR
CLE AR DIGI TAL
RAMPACCUMULATOR
I/O_UPDATE
POSITIVE
STEP SIZE
NEGATIVE
STEP SIZE
P DDS CLO CK CY CLES N DDS CL OCK CYCL E S 1 DDS CL OCK CYCL E
DIGITAL RAMP ENABL E
DROVER
CLEAR
RELEASE
AUTO
CLEAR
–Δt
t
1 2 3 4 5 6 7 8 9
10
11
12
13
10836-034
AD9914 Data Sheet
Rev. D | Page 26 of 48
Event 13An I/O update registers that the autoclear digital
ramp accumulator bit is set, resetting the ramp accumulator.
However, with an automatic clear, the ramp accumulator is held
in reset for only a single DDS clock cycle. This forces the DRG
output to the lower limit, but the ramp accumulator is immedi-
ately made available for normal operation. In this example, the
DRCTL pin remains Logic 1; therefore, the DRG output restarts
the previous positive ramp profile.
No-Dwell Ramp Generation
The two no-dwell high and no-dwell low bits (0x01[18:17]) in
CFR2 add to the flexibility of the DRG capabilities. During normal
ramp generation, when the DRG output reaches the programmed
upper or lower limit, it simply remains at the limit until the
operating parameters dictate otherwise. However, during no-dwell
operation, the DRG output does not necessarily remain at the limit.
For example, if the digital ramp no-dwell high bit is set when the
DRG reaches the upper limit, it automatically (and immediately)
snaps to the lower limit (that is, it does not ramp back to the lower
limit; it jumps to the lower limit). Likewise, when the digital ramp
no-dwell low bit is set, and the DRG reaches the lower limit, it
automatically (and immediately) snaps to the upper limit.
During no-dwell operation, the DRCTL pin is monitored for state
transitions only; that is, the static logic level is immaterial.
During no-dwell high operation, a positive transition of the
DRCTL pin initiates a positive slope ramp, which continues
uninterrupted (regardless of any further activity on the DRCTL
pin) until the upper limit is reached.
During no-dwell low operation, a negative transition of the DRCTL
pin initiates a negative slope ramp, which continues uninterrupted
(regardless of any further activity on the DRCTL pin) until the
lower limit is reached.
Setting both no-dwell bits invokes a continuous ramping mode
of operation; that is, the DRG output automatically oscillates
between the two limits using the programmed slope parameters.
Furthermore, the function of the DRCTL pin is slightly different.
Instead of controlling the initiation of the ramp sequence, it
only serves to change the direction of the ramp; that is, if the
DRG output is in the midst of a positive slope and the DRCTL
pin transitions from Logic 1 to Logic 0, the DRG immediately
switches to the negative slope parameters and resumes oscilla-
tion between the limits. Likewise, if the DRG output is in the
midst of a negative slope and the DRCTL pin transitions from
Logic 0 to Logic 1, the DRG immediately switches to the positive
slope parameters and resumes oscillation between the limits.
When both no-dwell bits are set, the DROVER signal produces
a positive pulse (two cycles of the DDS clock) each time the DRG
output reaches either of the programmed limits (assuming that
the DRG over output enable bit (0x01[13]) is set).
A no-dwell high DRG output waveform is shown in Figure 39.
The waveform diagram assumes that the digital ramp no-dwell
high bit is set and has been registered by an I/O update. The
status of the DROVER pin is also shown with the assumption
that the DRG over output enable bit has been set.
The circled numbers in Figure 39 indicate specific events, which
are explained as follows:
Event 1Indicates the instant that an I/O update registers that the
digital ramp enable bit is set.
Event 2DRCTL transitions to Logic 1, initiating a positive
slope at the DRG output.
Event 3DRCTL transitions to Logic 0, which has no effect on
the DRG output.
Event 4Because the digital ramp no-dwell high bit is set, the
moment that the DRG output reaches the upper limit, it imme-
diately switches to the lower limit, where it remains until the
next Logic 0 to Logic 1 transition of DRCTL.
Event 5DRCTL transitions from Logic 0 to Logic 1, which
restarts a positive slope ramp.
Event 6 and Event 7DRCTL transitions are ignored until the
DRG output reaches the programmed upper limit.
Event 8Because the digital ramp no-dwell high bit is set, the
moment that the DRG output reaches the upper limit, it immedi-
ately switches to the lower limit, where it remains until the next
Logic 0 to Logic 1 transition of DRCTL.
Operation with the digital ramp no-dwell low bit set (instead of
the digital ramp no-dwell high bit) is similar, except that the DRG
output ramps in the negative direction on a Logic 1 to Logic 0
transition of DRCTL and jumps to the upper limit upon
reaching the lower limit.
Figure 39. No-Dwell High Ramp Generation
UPPER LIMIT
P DDS CLO CK CY CLES
1 2 3 4 5 6 7 8
DRG OUTP UT
LOWER LIMIT
DRCTL
POSITIVE
STEP SIZE
DROVER
t
10836-035
Data Sheet AD9914
Rev. D | Page 27 of 48
DROVER Pin
The DROVER pin provides an external signal to indicate the status
of the DRG. Specifically, when the DRG output is at either of
the programmed limits, the DROVER pin is Logic 1; otherwise,
it is Logic 0. In the special case of both no-dwell bits set, the
DROVER pin pulses positive for two DDS clock cycles each
time the DRG output reaches either of the programmed limits.
Frequency Jumping Capability in DRG Mode
Another feature of the AD9914 allows the user to skip a predefined
range of frequencies during a normal sweep. The frequency jump
enable bit in CFR2 (0x01[14]) enables this functionality. When
this bit is set, the sweeping logic monitors the instantaneous
frequency. When it reaches the frequency point defined in the
lower frequency jump register (0x09) on the next accumulation
cycle, instead of accumulating a delta tuning word as in normal
sweeping, it skips directly to the frequency value set in the upper
frequency jump register (0x0A), and vice versa. Figure 40 shows
how this feature works.
A second frequency jump can also be allowed if the frequency
jump registers are reprogrammed before the sweeping is complete.
The following rules apply when this feature is enabled.
The frequency jump values must lie between the lower
limit and upper limit of the frequency sweep range.
The lower frequency jump register value must be lower
than that of the upper frequency jump register value.
Figure 40. Frequency vs. Time
POWER-DOWN CONTROL
The AD9914 offers the ability to independently power down
three specific sections of the device. Power-down functionality
applies to the following:
Digital core
DAC
Input REF CLK clock circuitry
A power-down of the digital core disables the ability to update
the serial/parallel I/O port. However, the digital power-down
bit (0x00[7]) can still be cleared to prevent the possibility of a
nonrecoverable state.
Software power-down is controlled via three independent
power-down bits in CFR1. Software control requires that the
EXT_PWR_DWN pin be forced to a Logic 0 state. In this case,
setting the desired power-down bits (0x00[7:5]) via the serial
I/O port powers down the associated functional block, whereas
clearing the bits restores the function.
Alternatively, all three functions can be simultaneously powered
down via external hardware control through the EXT_PWR_DWN
pin. When this pin is forced to Logic 1, all four circuit blocks are
powered down regardless of the state of the power-down bits;
that is, the independent power-down bits in CFR1 are ignored
and overridden when EXT_PWR_DWN is Logic 1.
Based on the state of the external power-down control bit, the
EXT_PWR_DWN pin produces either a full power-down or a
fast recovery power-down. The fast recovery power-down mode
maintains power to the DAC bias circuitry and the PLL, VCO,
and input clock circuitry. Although the fast recovery power-down
does not conserve as much power as the full power-down, it allows
the device to awaken very quickly from the power-down state.
FREQUENCY
t
UPPER LIMIT
0x09
0x0A
LOWER LIMIT
10836-036
AD9914 Data Sheet
Rev. D | Page 28 of 48
PROGRAMMING AND FUNCTION PINS
The AD9914 is equipped with a 32-bit parallel port. The 32-bit
port is for programming the internal registers of the device in
either serial mode or parallel mode as well as allowing for direct
modulation control of frequency (FTW), phase (POW), and
amplitude (AMP). The state of the external function pins (F0
to F3) determines how the 32-bit parallel port is configured.
Pin 28 to Pin 31 are the function pins. Refer to Table 10 for
possible configurations.
Note that the OSK enable bit, CFR1[8], must be set to enable
amplitude control, as shown in Tabl e 10.
Table 10. Parallel Port Configurations
Function Pins, 32-Bit Parallel Port Pin Assignment
F[3:0]1 Mode Description Bits[31:24]2 Bits[23:16]3 Bits[15:8]4 Bits[7:0]5
0000 Parallel programming mode Data[15:8]
(optional)
Data[7:0] Address[7:0] Used to control writes, reads, and
8-bit or 16-bit data-word. See the
Parallel Programming section for
details.
0001
Serial programming mode
Not used
Not used
Not used
Used to control SCLK, SDIO,
SDO, CS, and SYNCIO. See the
Serial Programming section for
details.
0010 Full 32 bits of direct frequency
tuning word control. MSB and LSB
aligned to parallel port pins
FTW[31:24] FTW[23:16] FTW[15:8] FTW[7:0]
0011 Full 32 bits of direct frequency
tuning word control with different
parallel port pin assignments
FTW[15:8] FTW[7:0] FTW[31:24] FTW[23:16]
0100 Full 16 bits of direct phase offset
control and full 12 bits of direct
amplitude control
POW[15:8] POW[7:0] AMP[11:8] AMP[7:0]
0101 Full 12 bits of direct amplitude
control and full 16 bits of direct
phase offset control
AMP[11:8] AMP[7:0] POW[15:8] POW[7:0]
0110 24 bits of partial FTW control and
8 bits of partial amplitude control
FTW[31:24] FTW[23:16] FTW[15:8] AMP[15:8]
0111 24 bits of partial FTW control and
8 bits of partial phase offset control
FTW[31:24] FTW[23:16] FTW[15:8] POW[15:8]
1000 24 bits of partial FTW control and
8 bits of partial amplitude control
FTW[31:24] FTW[23:16] FTW[15:8] AMP[7:0]
1001 24 bits of partial FTW control and
8 bits of partial phase offset control
FTW[31:24] FTW[23:16] FTW[15:8] POW[7:0]
1010 24 bits of partial FTW control and
8 bits of partial amplitude control
FTW[23:16] FTW[15:8] FTW[7:0] AMP[15:8]
1011 24 bits of partial FTW control and
8 bits of partial phase offset control
FTW[23:16] FTW[15:8] FTW[7:0] POW[15:8]
1100 24 bits of partial FTW control and
8 bits of partial amplitude control
FTW[23:16] FTW[15:8] FTW[7:0] AMP[7:0]
1101 24 bits of partial FTW control and
8 bits of partial phase offset control
FTW[23:16] FTW[15:8] FTW[7:0] POW[7:0]
1110 Not used Not used Not used Not used
1111 Not used Not used Not used Not used
1 Pin 31 to Pin 28.
2 Pin 68 to Pin 72, Pin 75 to 77.
3 Pin 78 to Pin 81, Pin 87, Pin 88, Pin 1, Pin 2.
4 Pin 3 to Pin 5, Pin 8 to Pin 12.
5 Pin 13 to Pin 15, Pin 18 to Pin 22.
Data Sheet AD9914
Rev. D | Page 29 of 48
Figure 41. Parallel Port Block Diagram
The 32-pin parallel port of the AD9914 works in conjunction
with an independent set of four function pins that control the
functionality of the parallel port. The 32 pins of the parallel port
constitute a 32-bit word designated by Bits[31:0] (31 indicating
the most significant bit (MSB) and 0 indicating the least significant
bit (LSB)), with the four function pins designated as F[3:0]. The
relationship between the function pins, the 32-pin parallel port,
the internal programming registers, and the DDS control
parameters (frequency, phase, and amplitude) is illustrated in
Figure 41. Note that the parallel port operates in three different
modes as defined by the function pins.
The parallel mode is in effect when the logic levels applied to
the function pins are F[3:0] = 0000. This allows the parallel port
to function as a parallel interface providing access to all of the
device programming registers. In parallel mode, the 32-pin port
(Bits[31:0]) is subdivided into three groups with Bits[31:16]
constituting 16 data bits, Bits[15:8] constituting eight address
bits, and Bits[2:0] constituting three control bits. The address
bits target a specific device register, whereas the data bits
constitute the register content. The control bits establish read or
write functionality as well as set the width of the data bus. That
is, the user can select whether the data bus spans 16 bits
(Bits[31:16]) or eight bits (Bits[23:16]). The parallel mode
allows the user to write to the device registers at rates of up to
200 MBps using 16-bit data (or 100 MBps using 8-bit data).
The serial mode is in effect when the logic levels applied to the
function pins are F[3:0] = 0001. This allows the parallel port to
function as a serial interface providing access to all of the device
programming registers. In this mode, only five pins of the 32-pin
parallel port are functional (Bits[4:0]). These pins provide chip
select (CS), serial clock (SCLK), and I/O synchronization
(SYNCIO) functionality for the serial interface, as well as two
serial data lines (SDO and SDIO). The serial mode supports
data rates of up to 80 Mbps.
When the logic levels applied to the function pins are F[3:0] =
0010 to 1101 (note that 1110 and 1111 are unused), the parallel
port functions as a high speed interface with direct access to the
32-bit frequency, 16-bit phase, and 12-bit amplitude parameters
of the DDS core. The table in Figure 41 shows the segmentation
of the 32-pin parallel port by identifying Bits[31:0] with the
frequency (FTW[31:0]), phase (POW[15:0]), and amplitude
(AMP[15:0]) parameters of the DDS. Note, however, that
although AMP[15:0] indicate 16-bit resolution, the actual
amplitude resolution is 12 bits. Therefore, only AMP[11:0]
provide amplitude control (that is, AMP[15:12] are not used).
PARALLEL
PORT PINS
4DECODE
D Q
CK
32 ROUTING
LOGIC
32
32
32
27 8
8
8
WR
RD
DIRE CT MO DE S
5
SDO
SYNCIO
SDIO
SCLK
CS
PARAL LEL M ODE
SERIAL M ODE
FTW FREQUENCY
PHASE
AMPLITUDE
DDS
32
16
12 POW
AMP
0000
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
1101
0001
0010
PARAL LEL M ODE
SERIAL M ODE
DIRE CT MO DE
OS K E NABLE
10836-046
NOTES
1. AM P [ 11: 0] CONTROL S AM P LITUDE. AMP[ 15: 12] UNUS E D.
FUNCTION
PINS
FUNCTION PINS AND DI RE CT MODE
BITS[31:0] VS. FTW, PO W , AMP
F[3:0]
BITS[31:0]
F[3:0] BITS[31:24] BITS[23:16] BITS[15:8] BITS[7:0]
FTW[31:24]
FTW[15:8]
POW[15:8]
AMP[11:8]
FTW[31:24]
FTW[31:24]
FTW[31:24]
FTW[31:24]
FTW[23:16]
FTW[23:16]
FTW[23:16]
FTW[23:16]
FTW[23:16]
FTW[7:0]
POW[7:0]
AMP[7:0]
FTW[23:16]
FTW[23:16]
FTW[23:16]
FTW[23:16]
FTW[15:8]
FTW[15:8]
FTW[15:8]
FTW[15:8]
FTW[15:8]
FTW[31:24]
AMP[11:8]
POW[15:8]
FTW[15:8]
FTW[15:8]
FTW[15:8]
FTW[15:8]
FTW[7:0]
FTW[7:0]
FTW[7:0]
FTW[7:0]
FTW[7:0]
FTW[23:16]
AMP[7:0]
POW[7:0]
AMP[15:8]
POW[15:8]
AMP[7:0]
POW[7:0]
AMP[15:8]
POW[15:8]
AMP[7:0]
POW[7:0]
PROGRAMMING
REGISTERS
IO_UPDATE
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
SERIAL
CONTROL
SYSTEM
CLOCK
SYNC_CLK
PARALLEL
CONTROL
BITS[31:24]
BITS[23:16]
BITS[15:8]
BIT 2
BIT 1
BIT 0
D[15:8]
D[7:0]
A[7:0]
16 BITS/ 8 BIT S
AD9914 Data Sheet
Rev. D | Page 30 of 48
Furthermore, to make use of amplitude control, the user must
be sure to program the OSK enable bit in the CFR1 register
(0x00[8]) to Logic 1.
The combination of the F[3:0] pins and Bits[31:0] provides the
AD9914 with unprecedented modulation capability by allowing
the user direct control of the DDS parameters (frequency, phase,
amplitude, or various combinations thereof). Furthermore, the
parallel port operates at a sample rate equal to 1/24 of the system
sample clock. This allows for updates of the DDS parameters at
rates of up to 145 MSPS (assuming a 3.5 GHz system clock)
allowing the AD9914 to accommodate applications with
wideband modulation requirements.
Be aware that the frequency, phase, and amplitude changes applied
at the parallel port travel to the DDS core over different paths,
experiencing different propagation times (latency). Therefore,
modulating more than one DDS parameter necessitates setting
the devices matched latency enable bit in the CFR2 register
(0x01[15]), which equalizes the latency of each DDS parameter
as it propagates from the parallel port to the DDS core. Note
that high speed modulation requires a DAC reconstruction
filter with sufficient bandwidth to accommodate the
instantaneous time domain transitions.
Because direct access to the DDS parameters occurs via the
FTW, POW, and AMP registers, the IO_UPDATE pin (see
Figure 41) adds another layer of flexibility. To accommodate
this functionality, the AD9914 provides a register control bit,
parallel port streaming enable (0x00[17]). When this bit is set
to Logic 1, the parallel port operates without the need for an
I/O update. When this bit is Logic 0, however, the device
delivers the parallel port data to the appropriate registers (FTW,
POW, AMP), but not to the DDS core. Data does not transfer to
the DDS core until the user asserts the IO_UPDATE pin.
For example, suppose that an application requires frequency and
amplitude modulation with full 32-bit frequency resolution and
full 12-bit amplitude resolution. Note that none of the F[3:0]
pin combinations supports such modulation capability directly.
To circumvent this problem, set the parallel port streaming
enable bit (0x00[17]) to Logic 0. This allows for the use of two
direct mode cycles of the 32-pin parallel port, each with a
different function pin setting, without affecting the DDS core
until assertion of the IO_UPDATE pin. That is, during the first
direct mode cycle, set the function pins to F[3:0] = 0010, which
routes all 32 bits to the FTW register (frequency). On the next
direct mode cycle, set the function pins to F[3:0] = 0100, which
provides full 12-bit access to the AMP register (amplitude). Be
aware, however, this also provides access to the POW register
(phase); therefore, be sure keep the phase bits static. Next, toggle
the IO_UPDATE pin, which synchronously transfers the new
frequency and phase values from the FTW and POW registers
to the DDS core. This mode of operation reduces the overall
modulation rate by a factor of three because it requires two
separate operations on the parallel port followed by an
IO_UPDATE. However, this still allows for modulation
sample rates as high as ~49 MSPS.
Data Sheet AD9914
Rev. D | Page 31 of 48
SERIAL PROGRAMMING
To enable SPI operations, set Pin 28 (F0) to logic high and Pin 29
to Pin 31 (F1 to F3) to logic low. To program the AD9914 with a
parallel interface, see the Parallel Programming section.
CONTROL INTERFACESERIAL I/O
The AD9914 serial port is a flexible, synchronous serial commu-
nications port allowing easy interface to many industry-standard
microcontrollers and microprocessors. The serial I/O is compatible
with most synchronous transfer formats.
The interface allows read/write access to all registers that configure
the AD9914. MSB-first or LSB-first transfer formats are supported.
In addition, the serial interface port can be configured as a single
pin input/output (SDIO) allowing a 2-wire interface, or it can be
configured as two unidirectional pins for input/output (SDIO
and SDO), enabling a 3-wire interface. Two optional pins
(I/O_SYNC and CS) enable greater flexibility for designing
systems with the AD9914.
Table 11. Serial I/O Pin Description
Pin No. Mnemonic Serial I/O Description
18 D4/SYNCIO SYNCIO
19 D3/SDO SDO
20 D2/SDIO/WR SDIO
21 D1/SCLK/RD SCLK
22
D0/CS/PWD CS—chip select
GENERAL SERIAL I/O OPERATION
There are two phases to a serial communications cycle. The first
is the instruction phase to write the instruction byte into the
AD9914. The instruction byte contains the address of the register
to be accessed and defines whether the upcoming data transfer
is a write or read operation.
For a write cycle, Phase 2 represents the data transfer between
the serial port controller to the serial port buffer. The number
of bytes transferred is a function of the register being accessed.
For example, when accessing Control Function Register 2
(Address 0x01), Phase 2 requires that four bytes be transferred.
Each bit of data is registered on each corresponding rising edge
of SCLK. The serial port controller expects that all bytes of the
register be accessed; otherwise, the serial port controller is put
out of sequence for the next communication cycle. However,
one way to write fewer bytes than required is to use the SYNCIO
pin feature. The SYNCIO pin function can be used to abort an
I/O operation and reset the pointer of the serial port controller.
After a SYNCIO, the next byte is the instruction byte. Note that
every completed byte written prior to a SYNCIO is preserved in
the serial port buffer. Partial bytes written are not preserved. At
the completion of any communication cycle, the AD9914 serial
port controller expects the next eight rising SCLK edges to be
the instruction byte for the next communication cycle.
After a write cycle, the programmed data resides in the serial
port buffer and is inactive. I/O_UPDATE transfers data from
the serial port buffer to active registers. The I/O update can be
sent either after each communication cycle or when all serial
operations are complete. In addition, a change in profile pins
can initiate an I/O update.
For a read cycle, Phase 2 is the same as the write cycle with the
following differences: data is read from the active registers, not
the serial port buffer, and data is driven out on the falling edge
of SCLK.
Note that, to read back any profile register (0x0B to 0x1A), the
three external profile pins must be used. For example, if the
profile register is Profile 5 (0x15), the PS[0:2] pins must equal
101.This is not required to write to the profile registers.
INSTRUCTION BYTE
The instruction byte contains the following information as
shown in the instruction byte information bit map.
Instruction Byte Information Bit Map
MSB LSB
I7 I6 I5 I4 I3 I2 I1 I0
R/W X A5 A4 A3 A2 A1 A0
R/WBit 7 of the instruction byte determines whether a read
or write data transfer occurs after the instruction byte write.
Logic 1 indicates a read operation. Logic 0 indicates a write
operation.
X—Bit 6 of the instruction byte is don’t care.
A5, A4, A3, A2, A1, A0Bit 5, Bit 4, Bit 3, Bit 2, Bit 1, and Bit 0
of the instruction byte determine which register is accessed
during the data transfer portion of the communications cycle.
SERIAL I/O PORT PIN DESCRIPTIONS
SCLKSerial Clock
The serial clock pin is used to synchronize data to and from the
AD9914 and to run the internal state machines.
CSChip Select Bar
CS is an active low input that allows more than one device on
the same serial communications line. The SDO and SDIO pins
go to a high impedance state when this input is high. If driven
high during any communications cycle, that cycle is suspended
until CS is reactivated low. Chip select (CS) can be tied low in
systems that maintain control of SCLK.
SDIOSerial Data Input/Output
Data is always written into the AD9914 on this pin. However,
this pin can be used as a bidirectional data line. Bit 1 of CFR1
(0x00) controls the configuration of this pin. The default is
Logic 0, which configures the SDIO pin as bidirectional.
AD9914 Data Sheet
Rev. D | Page 32 of 48
SDOSerial Data Out
Data is read from this pin for protocols that use separate lines
for transmitting and receiving data. When the AD9914 operates
in single bidirectional I/O mode, this pin does not output data
and is set to a high impedance state.
SYNCIO—Input/Output Reset
SYNCIO synchronizes the I/O port state machines without
affecting the contents of the addressable registers. An active
high input on the SYNCIO pin causes the current communication
cycle to abort. After SYNCIO returns low (Logic 0), another
communication cycle can begin, starting with the instruction
byte write.
I/O_UPDATEInput/Output Update
The I/O update initiates the transfer of written data from the
serial or parallel I/O port buffer to active registers. I/O_UPDATE
is active on the rising edge, and its pulse width must be greater
than one SYNC_CLK period.
SERIAL I/O TIMING DIAGRAMS
Figure 42 through Figure 45 provide basic examples of the timing
relationships between the various control signals of the serial
I/O port. Most of the bits in the register map are not transferred
to their internal destinations until assertion of an I/O update,
which is not included in the timing diagrams that follow.
Note that the SCLK stall condition between the instruction byte
cycle and data transfer cycle in Figure 42 to Figure 45 is not
required.
MSB/LSB TRANSFERS
The AD9914 serial port can support both most significant bit
(MSB) first or least significant bit (LSB) first data formats. This
functionality is controlled by Bit 0 in CFR1 (0x00). The default
format is MSB first. If LSB first is active, all data, including the
instruction byte, must follow LSB-first convention. Note that the
highest number found in the bit range column for each register is
the MSB, and the lowest number is the LSB for that register.
Figure 42. Serial Port Write Timing, Clock Stall Low
Figure 43. 3-Wire Serial Port Read Timing, Clock Stall Low
Figure 44. Serial Port Write Timing, Clock Stall High
Figure 45. 2-Wire Serial Port Read Timing, Clock Stall High
I
7
SDIO
INS TRUCTIO N CY CLE DATA TRANSFER CY CLE
SCLK
CS
I
6
I
5
I
4
I
3
I
2
I
1
I
0
D
7
D
6
D
5
D
4
D
3
D
2
D
1
D
0
10836-037
DO7
INS TRUCTIO N CY CLE DATA TRANSFER CY CLE
DON' T CARE
I7I6I5I4I3I2I1I0
SDIO
SCLK
CS
SDO DO6 DO5 DO4 DO3 DO2 DO1 DO0
10836-038
I
7
SDIO
INS TRUCTIO N CY CLE DATA TRANSFER CY CLE
SCLK
CS
I
6
I
5
I
4
I
3
I
2
I
1
I
0
D
7
D
6
D
5
D
4
D
3
D
2
D
1
D
0
10836-039
I
7
SDIO
INS TRUCTIO N CY CLE DATA TRANS FER CYCLE
SCLK
CS
I
6
I
5
I
4
I
3
I
2
I
1
I
0
D
O7
D
O6
D
O5
D
O4
D
O3
D
O2
D
O1
D
O0
10836-040
Data Sheet AD9914
Rev. D | Page 33 of 48
PARALLEL PROGRAMMING (8-/16-BIT)
The state of the external function pins (F0 to F3) determine the
type of interface used by the AD9914. Pin 28 to Pin 31 are
dedicated function pins. To enable the parallel mode interface
set Pin 28 to Pin 31 to logic low.
Parallel programming consists of eight address lines and either
eight or 16 bidirectional data lines for read/write operations.
The logic state on Pin 22 determines the width of the data lines
used. A logic low on Pin 22 sets the data width to eight bits, and
logic high sets the data width to 16 bits. In addition, parallel
mode has dedicated write/read control inputs. If 16-bit mode is
used, the upper byte, Bits[15:8], goes to the addressed register
and the lower byte, Bits[7:0], goes to the adjacent lower address.
Parallel I/O operation allows write access to each byte of any
register in a single I/O operation. Readback capability for each
register is included to ease designing with the AD9914.
Table 12. Parallel Port Read Timing (See Figure 46)
Parameter Value Unit Test Conditions/Comments
tADV 92 ns max Address to data valid time
t
AHD
0
ns min
Address hold time to RD signal
inactive
tRDLOV 69 ns max RD low to output valid
tRDHOZ 50 ns max RD high to data three-state
tRDLOW 69 ns max RD signal minimum low time
tRDHIGH 50 ns max RD signal minimum high time
Table 13. Parallel Port Write Timing (See Figure 47)
Parameter Value Unit Test Conditions / Comments
tASU 1 ns Address setup time to WR
signal active
tDSU 3.8 ns Data setup time to WR signal
active
tAHD 0 ns Address hold time to WR signal
inactive
t
DHD
0
ns
Data hold time to WR signal
inactive
tWRLOW 2.1 ns WR signal minimum low time
tWRHIGH 3.8 ns WR signal minimum high time
tWR 10.5 ns Minimum write time
Figure 46. Parallel Port Read Timing Diagram
Figure 47. Parallel Port Write Timing Diagram
A1
D1
A2
D2
A3
D3
A[7:0]
RD
D[7:0] OR
D[15:0]
t
RDHOZ
t
RDHIGH
t
RDLOW
t
RDLOV
t
ADV
t
AHD
10836-041
A1 A2 A3
D1 D2 D3
A[7:0]
WR
D[7:0] OR
D[15:0]
10836-042
t
WR
t
ASU
t
AHD
t
WRHIGH
t
DHD
t
DSU
t
WRLOW
AD9914 Data Sheet
Rev. D | Page 34 of 48
REGISTER MAP AND BIT DESCRIPTIONS
Table 14. Register Map
Register
Name (Serial
Address)
Bit Range
(Parallel
Address)
Bit 7
(MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1
Bit 0
(LSB)
Default
Value
(Hex)1
CFR1
Control
Function
Register 1
(0x00)
[7:0]
(0x00)
Digital
power-
down
DAC
power-
down
REF CLK
input
power-
down
Open External
power-down
control
Open SDIO input
only
LSB first
mode
0x08
[15:8]
(0x01)
Load LRR
at I/O
update
Autoclear
digital
ramp
accumu-
lator
Autoclear
phase
accumu-
lator
Clear digital
ramp
accumulator
Clear phase
accumulator
Open External
OSK enable
OSK
enable
0x00
[23:16]
(0x02)
Open Parallel port
streaming
enable
Enable
sine
output
0x01
[31:24]
(0x03)
Open VCO cal
enable
0x00
CFR2
Control
Function
Register 2
(0x01)
[7:0]
(0x04)
Open 0x00
[15:8]
(0x05)
Matched
latency
enable
Frequency
jump
enable
DRG over
output
enable
Open SYNC_CLK
enable
SYNC_CLK
invert
Reserved Open 0x09
[23:16]
(0x06)
Profile
mode
enable
Parallel
data port
enable
Digital ramp destination Digital ramp
enable
Digital
ramp no-
dwell high
Digital
ramp no-
dwell low
Program
modulus
enable
0x00
[31:24]
(0x07)
Open 0x00
CFR3
Control
Function
Register 3
(0x02)
[7:0]
(0x08)
Open Manual ICP
selection
ICP[2:0] Lock
detect
enable
Minimum LDW[1:0] 0x1C
[15:8]
(0x09)
Feedback Divider N[7:0] 0x19
[23:16]
(0x0A)
Open Input
divider
reset
Input divider[1:0] Doubler
enable
PLL enable PLL input
divider
enable
Doubler
clock edge
0x00
[31:24]
(0x0B)
Open 0x00
CFR4
Control
Function
Register 4
(0x03)
[7:0]
(0x0C)
Requires register default value settings (0x20) 0x20
[15:8]
(0x0D)
Requires register default value settings (0x21) 0x21
[23:16]
(0x0E)
Requires register default value settings (0x05) 0x05
[31:24]
(0x0F)
Open Auxiliary
divider
power-
down
DAC CAL
clock
power-
down
DAC CAL
enable2
0x00
Digital Ramp
Lower Limit
Register
(0x04)
[7:0]
(0x10)
Digital ramp lower limit[7:0] 0x00
[15:8]
(0x11)
Digital ramp lower limit[15:8] 0x00
[23:16]
(0x12)
Digital ramp lower limit[23:16] 0x00
[31:24]
(0x13)
Digital ramp lower limit[31:24] 0x00
Data Sheet AD9914
Rev. D | Page 35 of 48
Register
Name (Serial
Address)
Bit Range
(Parallel
Address)
Bit 7
(MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1
Bit 0
(LSB)
Default
Value
(Hex)1
Digital Ramp
Upper
Limit
Register
(0x05)
[7:0]
(0x14)
Digital ramp upper limit[7:0] 0x00
[15:8]
(0x15)
Digital ramp upper limit[15:8] 0x00
[23:16]
(0x16)
Digital ramp upper limit[23:16] 0x00
[31:24]
(0x17)
Digital ramp upper limit[31:24] 0x00
Rising Digital
Ramp Step
Size
Register
(0x06)
[7:0]
(0x18)
Rising digital ramp increment step size[7:0] N/A
[15:8]
(0x19)
Rising digital ramp increment step size[15:8] N/A
[23:16]
(0x1A)
Rising digital ramp increment step size[23:16] N/A
[31:24]
(0x1B)
Rising digital ramp increment step size[31:24] N/A
Falling Digital
Ramp Step
Size
Register
(0x07)
[7:0]
(0x1C)
Falling digital ramp decrement step size[7:0] N/A
[15:8]
(0x1D)
Falling digital ramp decrement step size[15:8] N/A
[23:16]
(0x1E)
Falling digital ramp decrement step size[23:16] N/A
[31:24]
(0x1F)
Falling digital ramp decrement step size[31:24] N/A
Digital Ramp
Rate
Register
(0x08)
[7:0]
(0x20)
Digital ramp positive slope rate[7:0] N/A
[15:8]
(0x21)
Digital ramp positive slope rate[15:8] N/A
[23:16]
(0x22)
Digital ramp negative slope rate[7:0] N/A
[31:24]
(0x23)
Digital ramp negative slope rate[15:8] N/A
Lower
Frequency
Jump
Register
(0x09)
[7:0]
(0x24)
Lower frequency jump point[7:0] 0x00
[15:8]
(0x25)
Lower frequency jump point[15:8] 0x00
[23:16]
(0x26)
Lower frequency jump point[23:16] 0x00
[31:24]
(0x27)
Lower frequency jump point[31:24] 0x00
Upper
Frequency
Jump
Register
(0x0A)
[7:0]
(0x28)
Upper frequency jump point[7:0] 0x00
[15:8]
(0x29)
Upper frequency jump point[15:8] 0x00
[23:16]
(0x2A)
Upper frequency jump point[23:16] 0x00
[31:24]
(0x2B)
Upper frequency jump point[31:24] 0x00
Profile 0 (P0)
Frequency
Tuning
Word 0
Register
(0x0B)
[7:0]
(0x2C)
Frequency Tuning Word 0[7:0] 0x00
[15:8]
(0x2D)
Frequency Tuning Word 0[15:8] 0x00
[23:16]
(0x2E)
Frequency Tuning Word 0[23:16] 0x00
[31:24]
(0x2F)
Frequency Tuning Word 0[31:24] 0x00
AD9914 Data Sheet
Rev. D | Page 36 of 48
Register
Name (Serial
Address)
Bit Range
(Parallel
Address)
Bit 7
(MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1
Bit 0
(LSB)
Default
Value
(Hex)1
Profile 0 (P0)
Phase/
Amplitude
Register
(0x0C)
[7:0]
(0x30)
Phase Offset Word 0[7:0] 0x00
[15:8]
(0x31)
Phase Offset Word 0[15:8] 0x00
[23:16]
(0x32)
Amplitude Scale Factor 0[7:0] 0x00
[31:24]
(0x33)
Open Amplitude Scale Factor 0[11:8] 0x00
Profile 1 (P1)
Frequency
Tuning
Word 1
Register
(0x0D)
[7:0]
(0x34)
Frequency Tuning Word 1[7:0] N/A
[15:8]
(0x35)
Frequency Tuning Word 1[15:8] N/A
[23:16]
(0x36)
Frequency Tuning Word 1[23:16] N/A
[31:24]
(0x37)
Frequency Tuning Word 1[31:24] N/A
Profile 1 (P1)
Phase/
Amplitude
Register
(0x0E)
[7:0]
(0x38)
Phase Offset Word 1[7:0] N/A
[15:8]
(0x39)
Phase Offset Word 1[15:8] N/A
[23:16]
(0x3A)
Amplitude Scale Factor 1[7:0] N/A
[31:24]
(0x3B)
Open Amplitude Scale Factor 1[11:8] N/A
Profile 2 (P2)
Frequency
Tuning
Word 2
Register
(0x0F)
[7:0]
(0x3C)
Frequency Tuning Word 2[7:0] N/A
[15:8]
(0x3D)
Frequency Tuning Word 2[15:8] N/A
[23:16]
(0x3E)
Frequency Tuning Word 2[23:16] N/A
[31:24]
(0x3F)
Frequency Tuning Word 2[31:24] N/A
Profile 2 (P2)
Phase/
Amplitude
Register
(0x10)
[7:0]
(0x40)
Phase Offset Word 2[7:0] N/A
[15:8]
(0x41)
Phase Offset Word 2[15:8] N/A
[23:16]
(0x42)
Amplitude Scale Factor 2[7:0] N/A
[31:24]
(0x43)
Open Amplitude Scale Factor 2[11:8] N/A
Profile 3 (P3)
Frequency
Tuning
Word 3
Register
(0x11)
[7:0]
(0x44)
Frequency Tuning Word 3[7:0] N/A
[15:8]
(0x45)
Frequency Tuning Word 3[15:8] N/A
[23:16]
(0x46)
Frequency Tuning Word 3[23:16] N/A
[31:24]
(0x47)
Frequency Tuning Word 3[31:24] N/A
Profile 3 (P3)
Phase/
Amplitude
Register
(0x12)
[7:0]
(0x48)
Phase Offset Word 3[7:0] N/A
[15:8]
(0x49)
Phase Offset Word 3[15:8] N/A
[23:16]
(0x4A)
Amplitude Scale Factor 3[7:0] N/A
[31:24]
(0x4B)
Open Amplitude Scale Factor 3[11:8] N/A
Data Sheet AD9914
Rev. D | Page 37 of 48
Register
Name (Serial
Address)
Bit Range
(Parallel
Address)
Bit 7
(MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1
Bit 0
(LSB)
Default
Value
(Hex)1
Profile 4 (P4)
Frequency
Tuning
Word 4
Register
(0x13)
[7:0]
(0x4C)
Frequency Tuning Word 4[7:0] N/A
[15:8]
(0x4D)
Frequency Tuning Word 4[15:8] N/A
[23:16]
(0x4E)
Frequency Tuning Word 4[23:16] N/A
[31:24]
(0x4F)
Frequency Tuning Word 4[31:24] N/A
Profile 4 (P4)
Phase/
Amplitude
Register
(0x14)
[7:0]
(0x50)
Phase Offset Word 4[7:0] N/A
[15:8]
(0x51)
Phase Offset Word 4[15:8] N/A
[23:16]
(0x52)
Amplitude Scale Factor 4[7:0] N/A
[31:24]
(0x53)
Open Amplitude Scale Factor 4[11:8] N/A
Profile 5 (P5)
Frequency
Tuning
Word 5
Register
(0x15)
[7:0]
(0x54)
Frequency Tuning Word 5[7:0] N/A
[15:8]
(0x55)
Frequency Tuning Word 5[15:8] N/A
[23:16]
(0x56)
Frequency Tuning Word 5[23:16] N/A
[31:24]
(0x57)
Frequency Tuning Word 5[31:24] N/A
Profile 5 (P5)
Phase/
Amplitude
Register
(0x16)
[7:0]
(0x58)
Phase Offset Word 5[7:0] N/A
[15:8]
(0x59)
Phase Offset Word 5[15:8] N/A
[23:16]
(0x5A)
Amplitude Scale Factor 5[7:0] N/A
[31:24]
(0x5B)
Open Amplitude Scale Factor 5[11:8] N/A
Profile 6 (P6)
Frequency
Tuning
Word 6
Register
(0x17)
[7:0]
(0x5C)
Frequency Tuning Word 6[7:0] N/A
[15:8]
(0x5D)
Frequency Tuning Word 6[15:8] N/A
[23:16]
(0x5E)
Frequency Tuning Word 6[23:16] N/A
[31:24]
(0x5F)
Frequency Tuning Word 6[31:24] N/A
Profile 6 (P6)
Phase/
Amplitude
Register
(0x18)
[7:0]
(0x60)
Phase Offset Word 6[7:0] N/A
[15:8]
(0x61)
Phase Offset Word 6[15:8] N/A
[23:16]
(0x62)
Amplitude Scale Factor 6[7:0] N/A
[31:24]
(0x63)
Open Amplitude Scale Factor 6[11:8] n/a
Profile 7 (P7)
Frequency
Tuning
Word 7
Register
(0x19)
[7:0]
(0x64)
Frequency Tuning Word 7[7:0] N/A
[15:8]
(0x65)
Frequency Tuning Word 7[15:8] N/A
[23:16]
(0x66)
Frequency Tuning Word 7[23:16] N/A
[31:24]
(0x67)
Frequency Tuning Word 7[31:24] N/A
AD9914 Data Sheet
Rev. D | Page 38 of 48
Register
Name (Serial
Address)
Bit Range
(Parallel
Address)
Bit 7
(MSB) Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1
Bit 0
(LSB)
Default
Value
(Hex)1
Profile 7 (P7)
Phase/
Amplitude
Register
(0x1A)
[7:0]
(0x68)
Phase Offset Word 7[7:0] N/A
[15:8]
(0x69)
Phase Offset Word 7[15:8] N/A
[23:16]
(0x6A)
Amplitude Scale Factor 7[7:0] N/A
[31:24]
(0x6B)
Open Amplitude Scale Factor 7[11:8] N/A
USR0 (0x1B) [7:0]
(0x6C)
Requires register default value settings (0x00) 0x00
[15:8]
(0x6D)
Requires register default value settings (0x08) 0x08
[23:16]
(0x6E)
Requires register default value settings (0x00) 0x00
[31:24]
(0x6F)
Open PLL lock Read
only
1 A master reset is required after power up. The master reset returns the internal registers to their default values.
2 The DAC CAL enable bit must be manually set and then cleared after each power-up and every time REF CLK or the internal system clock is changed. This initiates an
internal calibration routine to optimize the setup and hold times for internal DAC timing. Failure to calibrate degrades ac performance or makes the part
nonfunctional.
Data Sheet AD9914
Rev. D | Page 39 of 48
REGISTER BIT DESCRIPTIONS
The serial I/O port registers span an address range of 0 to 27
(0x00 to 0x1B in hexadecimal notation). This represents a total
of 28 individual serial registers. If programming in parallel mode,
the number of parallel registers increases to 112 individual parallel
registers. Additionally, the registers are assigned names according
to their functionality. In some cases, a register is given a mnemonic
descriptor. For example, the register at Serial Address 0x00 is
named Control Function Register 1 and is assigned the
mnemonic CFR1.
This section provides a detailed description of each bit in the
AD9914 register map. For cases in which a group of bits serves
a specific function, the entire group is considered a binary word
and is described in aggregate.
This section is organized in sequential order of the serial addresses
of the registers. Each subheading includes the register name and
optional register mnemonic (in parentheses). Also given is the
serial address in hexadecimal format and the number of bytes
assigned to the register.
Following each subheading is a table containing the individual
bit descriptions for that particular register. The location of the
bit(s) in the register is indicated by a single number or a pair of
numbers separated by a colon; that is, a pair of numbers (A:B)
indicates a range of bits from the most significant (A) to the
least significant (B). For example, [5:2] implies Bit Position 5 to
Bit Position 2, inclusive, with Bit 0 identifying the LSB of the
register.
Unless otherwise stated, programmed bits are not transferred to
their internal destinations until the assertion of the I/O_UPDATE
pin or a profile pin change.
Control Function Register 1 (CFR1)Address 0x00
Table 15. Bit Description for CFR1
Bits Mnemonic Description
[31:25] Open
24
VCO cal enable
1 = initializes the auto internal PLL calibration. The calibration is required if the PLL is to
provide the internal system clock. Must first be reset to Logic 0 before another calibration can
be issued.
[23:18] Open Open.
17 Parallel port streaming
enable
0 = the 32 bit parallel port needs an I/O update to activate or register any FTW, POW, or AMP
data presented to the 32-bit parallel port.
1 = the parallel port continuously samples data on the 32 input pins using SYNC_CLK and
multiplexes the value of FTW/POW/AMP accordingly, per the configuration of the F0 to F3 pins,
without the need of an I/O update. Data must meet the setup and hold times of the SYNC_CLK
rising edge. If the function pins are used dynamically to alter data between parameters, they
must also meet the timing of the SYNC_CLK edge.
16
Enable sine output
0 = cosine output of the DDS is selected.
1 = sine output of the DDS is selected (default).
15 Load LRR at I/O update Ineffective unless CFR2[19] = 1.
0 = normal operation of the digital ramp timer (default).
1 = interrupts the digital ramp timer operation to load a new linear ramp rate (LRR) value any
time I/O_UPDATE is asserted or a PS[2:0] change occurs.
14
Autoclear digital ramp
accumulator
0 = normal operation of the DRG accumulator (default).
1 = the digital ramp accumulator is reset for one cycle of the DDS clock (SYNC_CLK), after
which the accumulator automatically resumes normal operation. As long as this bit remains
set, the ramp accumulator is momentarily reset each time an I/O update is asserted or a PS[2:0]
change occurs. This bit is synchronized with either an I/O update or a PS[2:0] change and the
next rising edge of SYNC_CLK.
13 Autoclear phase accumulator 0 = normal operation of the DDS phase accumulator (default).
1 = synchronously resets the DDS phase accumulator anytime I/O_UPDATE is asserted or a
profile change occurs.
12 Clear digital ramp
accumulator
0 = normal operation of the digital ramp generator (default).
1 = asynchronous, static reset of the DRG accumulator. The ramp accumulator remains reset as
long as this bit remains set. This bit is synchronized with either an I/O update or a PS[2:0]
change and the next rising edge of SYNC_CLK.
11 Clear phase accumulator 0 = normal operation of the DDS phase accumulator (default).
1 = asynchronous, static reset of the DDS phase accumulator as long as this bit is set. This bit is
synchronized with either an I/O update or a PS[2:0] change and the next rising edge of
SYNC_CLK.
10 Open Open.
AD9914 Data Sheet
Rev. D | Page 40 of 48
Bits Mnemonic Description
9 External OSK enable 0 = manual OSK enabled (default).
1 = automatic OSK enabled.
Ineffective unless CFR1[8] = 1.
8 OSK enable 0 = OSK disabled (default).
1 = OSK enabled. To engage any digital amplitude adjust using DRG, profile, or direct mode via
the 32-bit parallel port, or OSK pin, this bit must be set.
7 Digital power-down This bit is effective without the need for an I/O update.
0 = clock signals to the digital core are active (default).
1 = clock signals to the digital core are disabled.
6 DAC power-down 0 = DAC clock signals and bias circuits are active (default).
1 = DAC clock signals and bias circuits are disabled.
5 REFCLK input power-down This bit is effective without the need for an I/O update.
0 = REFCLK input circuits and PLL are active (default).
1 = REFCLK input circuits and PLL are disabled.
4 Open Open.
3 External power-down control 0 = assertion of the EXT_PWR_DWN pin affects power-down.
1 = assertion of the EXT_PWR_DWN pin affects fast recovery power-down.
2 Open Open.
1 SDIO input only 0 = configures the SDIO pin for bidirectional operation; 2-wire serial programming
mode (default).
1 = configures the serial data I/O pin (SDIO) as an input only pin; 3-wire serial
programming mode.
0 LSB first mode 0 = configures the serial I/O port for MSB-first format (default).
1 = configures the serial I/O port for LSB-first format.
Control Function Register 2 (CFR2)Address 0x01
Table 16. Bit Descriptions for CFR2
Bit(s)
Mnemonic
Description
[31:24] Open Open.
23
Profile mode enable
0 = disables profile mode functionality (default).
1 = enables profile mode functionality. Profile pins are used to select the desired profile.
22 Parallel data port enable See the Parallel Data Port Modulation Mode section for more details.
0 = disables parallel data port modulation functionality (default).
1 = enables parallel data port modulation functionality.
[21:20] Digital ramp destination See Table 9 for details. Default is 00. See the Digital Ramp Generator (DRG) section for more
details.
19 Digital ramp enable 0 = disables digital ramp generator functionality (default).
1 = enables digital ramp generator functionality.
18 Digital ramp no-dwell high See the Digital Ramp Generator (DRG) section for details.
0 = disables no-dwell high functionality (default).
1 = enables no-dwell high functionality.
17 Digital ramp no-dwell low See the Digital Ramp Generator (DRG) section for details.
0 = disables no-dwell low functionality (default).
1 = enables no-dwell low functionality.
16 Programmable modulus
enable
0 = disables programmable modulus.
1 = enables programmable modulus.
15 Matched latency enable 0 = simultaneous application of amplitude, phase, and frequency changes to the DDS arrive at
the output in the order listed in Table 2 under data latency (pipe line delay)(default).
1 = simultaneous application of amplitude, phase, and frequency changes to the DDS arrive at
the output simultaneously.
14 Frequency jump enable 0 = disables frequency jump.
1 = enables frequency jump mode. Must have the digital generator DRG enabled for this feature.
13 DRG over output enable 0 = disables the DROVER output.
1 = enables the DROVER output.
Data Sheet AD9914
Rev. D | Page 41 of 48
Bit(s) Mnemonic Description
12 Open Open.
11 SYNC_CLK enable 0 = the SYNC_CLK pin is disabled and forced to a static Logic 0 state; the internal clock signal
continues to operate and provide timing to the data assembler.
1 = the internal SYNC_CLK signal appears at the SYNC_CLK pin (default).
10 SYNC_CLK invert 0 = normal SYNC_CLK polarity; Q data associated with Logic 1, I data with Logic 0 (default).
1 = inverted SYNC_CLK polarity.
9 Reserved Keep logic 0.
[8:0] Open Open.
Control Function Register 3 (CFR3)Address 0x02
Table 17. Bit Descriptions for CFR3
Bit(s) Mnemonic Description
[31:23]
Open
Open.
22 Input divider reset 0 = disables input divider reset function.
1 = initiates an input divider reset.
[21:20] Input divider Divides the input REF CLK signal by one of four values (1, 2, 4, 8). Bit 17 must be set to Logic 1
to enable the PLL input divider.
00 = divide by 1.
01 = divide by 2.
10 = divide by 4.
11 = divide by 8.
19 Doubler enable 0 = disables the doubler feature.
1 = enables the doubler feature. Must have the doubler clock edge bit set to Logic 1 to utilize
this feature.
18 PLL enable 0 = disables the internal PLL.
1 = the internal PLL is enabled and the output generates the system clock. The PLL must be
calibrated when enabled via VCO calibration in Register CFR1, Bit 24.
17 PLL input divider enable 0 = disables the PLL input divider function.
1 = enables the PLL input divider function.
16
Doubler clock edge
0 = disables the internal doubler circuit.
1 = enables the doubler circuit. Must have doubler enable bit set to Logic 1 to utilize this
feature.
[15:8] Feedback divider N The N divider value in Bits[15:8] is one part of the total PLL multiplication available. The second
part is the fixed divide by two element in the feedback path. Therefore, the total PLL
multiplication value is 2N. The valid N divider range is 10× to 255×. The default N value for
Bits[15:8] = 25. This sets the total default PLL multiplication to 50× or 2N.
7 Open Open.
6 Manual ICP selection 0 = the internal charge pump current is chosen automatically during the VCO calibration
routine (default).
1 = the internal charge pump is set manually per Table 7.
[5:3]
I
CP
Manual charge pump current selection. See Table 7.
2 Lock detect enable 0 = disables PLL lock detection.
1 = enables PLL lock detection.
[1:0] Minimum LDW Selects the number of REF CLK cycles that the phase error (at the PFD inputs) must remain
within before a PLL lock condition can be read back via Bit 24 in Register 0x00.
00 = 128 REF CLK cycles.
01 = 256 REF CLK cycles.
10 = 512 REF CLK cycles.
11 = 1024 REF CLK cycles.
AD9914 Data Sheet
Rev. D | Page 42 of 48
Control Function Register 4 (CFR4)—Address 0x03
Table 18. Bit Descriptions for DAC
Bit(s) Mnemonic Description
[31:27] Open Open
26 Auxiliary divider
power-down
0 = enables the SYNC OUT circuitry.
1 = disables the SYNC OUT circuitry
25 DAC CAL clock
power-down
0 = enables the DAC CAL clock if Bit 26 in Register 0x03 is Logic 0.
1 = disables the DAC CAL clock.
24 DAC CAL enable 1 = initiates an auto DAC calibration. The DAC CAL calibration is required at power-up and
any time the internal system clock is changed.
[23:0]
(See description)
These bits must always be programmed with the default values listed in the default column
in Table 14.
Digital Ramp Lower Limit RegisterAddress 0x04
This register is effective only if the digital ramp enable bit in the CFR2 register (0x01[19]) = 1. See the Digital Ramp Generator (DRG)
section for details.
Table 19. Bit Descriptions for Digital Ramp Lower Limit Register
Bit(s) Mnemonic Description
[31:0] Digital ramp lower limit 32-bit digital ramp lower limit value.
Digital Ramp Upper Limit RegisterAddress 0x05
This register is effective only if the digital ramp enable bit in the CFR2 register (0x01[19]) = 1. See the Digital Ramp Generator (DRG)
section for details.
Table 20. Bit Descriptions for Digital Ramp Limit Register
Bit(s) Mnemonic Description
[31:0]
Digital ramp upper limit
32-bit digital ramp upper limit value.
Rising Digital Ramp Step Size RegisterAddress 0x06
This register is effective only if the digital ramp enable bit in the CFR2 register (0x01[19]) = 1. See the Digital Ramp Generator (DRG)
section for details.
Table 21. Bit Descriptions for Rising Digital Ramp Step Size Register
Bit(s) Mnemonic Description
[31:0] Rising digital ramp
increment step size
32-bit digital ramp increment step size value.
Falling Digital Ramp Step Size RegisterAddress 0x07
This register is effective only if the digital ramp enable bit in the CFR2 register (0x01[19]) = 1. See the Digital Ramp Generator (DRG)
section for details.
Table 22. Bit Descriptions for Falling Digital Ramp Step Size Register
Bit(s) Mnemonic Description
[31:0]
Falling digital ramp
decrement step size
32-bit digital ramp decrement step size value.
Data Sheet AD9914
Rev. D | Page 43 of 48
Digital Ramp Rate RegisterAddress 0x08
This register is effective only if the digital ramp enable bit in the CFR2 register (0x01[19]) = 1. See the Digital Ramp Generator (DRG)
section for details.
Table 23. Bit Descriptions for Digital Ramp Rate Register
Bit(s) Mnemonic Description
[31:16]
Digital ramp negative slope
rate
16-bit digital ramp negative slope value that defines the time interval between decrement
values.
[15:0] Digital ramp positive slope
rate
16-bit digital ramp positive slope value that defines the time interval between increment
values.
Lower Frequency Jump RegisterAddress 0x09
This register is effective only if the digital ramp enable bit (0x01[19]) = 1 and the frequency jump enable bit (0x01[14]) = 1 in the CFR2
register. See the Digital Ramp Generator (DRG) section for details.
Table 24. Bit Descriptions for Lower Frequency Jump Register
Bit(s) Mnemonic Description
[31:0] Lower frequency jump
point
32-bit digital lower frequency jump value. Any time the lower frequency jump value is
reached during a frequency sweep, the output frequency jumps to the upper frequency
value instantaneously and continues frequency sweeping in a phase-continuous manner.
Upper Frequency Jump RegisterAddress 0x0A
This register is effective only if the digital ramp enable bit (0x01[19]) = 1 and the frequency jump enable bit (0x01[14]) = 1 in the CFR2
register. See the Digital Ramp Generator (DRG) section for details.
Table 25. Bit Descriptions for Upper Frequency Jump Register
Bit(s) Mnemonic Description
[31:0] Upper frequency jump
point
32-bit digital upper frequency jump value. Any time the upper frequency jump value is
reached during a frequency sweep, the output frequency jumps to the lower frequency
value instantaneously and continues frequency sweeping in a phase-continuous manner.
AD9914 Data Sheet
Rev. D | Page 44 of 48
Profile Registers
There are 16 serial I/O addresses (Address 0x0B to Address 0x01A)
dedicated to device profiles. Eight of the 16 profiles house up to
eight single tone frequencies. The remaining eight profiles contain
the corresponding phase offset and amplitude parameters
relative to the profile pin setting. To enable profile mode, set the
profile mode enable bit in CFR2 (0x01[23]) = 1. The active
profile register is selected using the external PS[2:0] pins.
Profile 0 to Profile 7, Single Tone Registers0x0B, 0x0D, 0x0F, 0x11, 0x13, 0x15, 0x17, 0x19
Four bytes are assigned to each register.
Table 26. Bit Descriptions for Profile 0 to Profile 7 Single Tone Registers
Bit(s) Mnemonic Description
[31:0] Frequency tuning word This 32-bit number controls the DDS frequency.
Profile 0 to Profile 7, Phase Offset and Amplitude Registers0x0C, 0x0E, 0x10, 0x12, 0x14, 0x16, 0x18, 0x1A
Four bytes are assigned to each register.
Table 27. Bit Descriptions for Profile 0 to Profile 7 Phase Offset and Amplitude Registers
Bit(s) Mnemonic Description
[31:28] Open Open.
[27:16] Amplitude scale factor This 12-bit word controls the DDS frequency. Note that the OSK enable bit (0x00[8]) must
be set to logic high to make amplitude adjustments.
[15:0] Phase offset word This 16-bit word controls the DDS frequency.
USR0 RegisterAddress 0x1B
Table 28. Bit Descriptions for USR0 Register
Bit(s) Mnemonic Description
[31:25] Open
24 PLL lock This is a readback bit only. If Logic 1 is read back, the PLL is locked. Logic 0 represents a
nonlocked state.
[23:0] (See description) These bits must always be programmed with the default values listed in the default column
in Table 14.
Data Sheet AD9914
Rev. D | Page 45 of 48
OUTLINE DIMENSIONS
Figure 48. 88-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
12 mm × 12 mm Body, Very Thin Quad
(CP-88-5)
Dimensions shown in millimeters
ORDERING GUIDE
Parameter1 Temperature Range Package Description Package Option
AD9914BCPZ
−40°C to +85°C
88-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
CP-88-5
AD9914BCPZ-REEL7 −40°C to +85°C 88-Lead Lead Frame Chip Scale Package [LFCSP_VQ] CP-88-5
AD9914/PCBZ Evaluation Board
1 Z = RoHS Compliant Part.
*COMPLIANT TO JEDE C S TANDARDS MO-220- V RRD
EXCEPT FOR MINIMUM THICKNESSAND L E AD COUNT.
07-02-2012-B
1
22
66
45 23
44
88
67
0.50
0.40
0.30
0.30
0.23
0.18
10.50
REF
0.60 M AX
0.60
MAX
6.70
REF SQ
0.50
BSC
0.138~0.194 REF
12° M AX
SEATING
PLANE
TOP VIEW
EXPOSED PAD
BOTTOM VIEW
0.70
0.65
0.60 0.045
0.025
0.005
PI N 1
INDICATOR
12.10
12.00 S Q
11.90
11.85
11. 75 S Q
11.65
PI N 1
INDICATOR
*0.90
0.85
0.75
FOR PRO P E R CONNECTION O F
THE EXPOSED PAD, REFER TO
THE P IN CONFI GURATIO N AND
FUNCTION DES CRIPT IO NS
SECTION OF THIS DATA SHEET.
COPLANARITY
0.08
AD9914 Data Sheet
Rev. D | Page 46 of 48
NOTES
Data Sheet AD9914
Rev. D | Page 47 of 48
NOTES
AD9914 Data Sheet
Rev. D | Page 48 of 48
NOTES
©20122014 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D10836-0-1/14(D)
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Analog Devices Inc.:
AD9914/PCBZ AD9914BCPZ AD9914BCPZ-REEL7