REVISIONS
LTR DESCRIPTION DATE (YR-MO-DA) APPROVED
REV
SHEET
REV
SHEET
REV STATUS REV
OF SHEETS SHEET 12345678910
PMIC N/A PREPARED BY
RICK OFFICER
DEFENSE SUPPLY CENTER COLUMBUS
STANDARD
MICROCIRCUIT
DRAWING
CHECKED BY
RAJESH PITHADIA COLUMBUS, OHIO 43216
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
DEPARTMENTS
APPROVED BY
RAY M OND MONNIN MICROCI RCUIT, LINEAR, MICROPOWER,
PRECISION OPERATIONAL AMPLI FIER,
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE
98-11-05 MONOLITHIC SILICON
AMSC N/A REVISION LEVEL SIZE
ACAGE CODE
67268 5962-99502
SHEET 1 OF 10
DSCC FORM 2233
APR 97 5962-E018-98
DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.
STANDARD
MICROCI RCUIT DRAWI NG SIZE
A5962-99502
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000 REVISION LEVEL SHEET
2
DSCC FORM 2234
APR 97
1. SCOPE
1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and
M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the
Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels are reflected in the
PIN.
1.2 PIN. The PIN is as shown in the following example:
5962 - 99502 01 Q G X
Federal RHA Device Device Case Lead
stock class designator type class outline finish
designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5)
\ / (see 1.2.3)
\/
Drawing number
1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and
are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A
specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device.
1.2.2 Device type(s). The device type(s) identify the circuit function as follows:
Device type Generic number Circuit function
01 LT1077 Micropower, single supply, precision
operational amplifier
1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as
follows:
Device class Device requirements documentation
M Vendor self-certification to the requirements for MIL-STD-883 compliant,
non-JAN class level B microcircuits in accordance with MIL-PRF-38535,
appendix A
Q or V Certification and qualification to MIL-PRF-38535
1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows:
Outline letter Descriptive designator Terminals Package style
G MACY1-X8 8 Can
P GDIP1-T8 or CDIP2-T8 8 Dual-in-line
1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535,
appendix A for device class M.
STANDARD
MICROCI RCUIT DRAWI NG SIZE
A5962-99502
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000 REVISION LEVEL SHEET
3
DSCC FORM 2234
APR 97
1.3 Absolute maximum ratings. 1/
Supply voltage (
VS)..........................................................................
22 V
Differential input voltage ....................................................................
30 V
Input voltage (VIN)..............................................................................Equal to positive supply voltage
5 V below negative supply voltage
Power dissipation (PD) .......................................................................(
VS) IS
Output short circuit duration...............................................................Indefinite
Junction temperature (TJ) ..................................................................150
C
Storage temperature range................................................................-65
C to +150
C
Lead temperature (soldering, 10 seconds)........................................300
C
Thermal regulation, junction-to-case (
JC) .........................................See MIL-STD-1835
Thermal resistance, junction-to-ambient (
JA):
Case G ...........................................................................................150
C/W
Case P............................................................................................100
C/W
1.4 Recommended operating conditions.
Supply voltage (
VS)..........................................................................+5 V,
15 V
Ambient operating temperature range (TA)........................................-55
C to +125
C
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a
part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in
the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the
solicitation.
SPECIFICATION
DEPARTMENT OF DEFENSE
MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.
STANDARDS
DEPARTMENT OF DEFENSE
MIL-STD-883 - Test Method Standard Microcircuits.
MIL-STD-973 - Configuration Management.
MIL-STD-1835 - Interface Standard For Microcircuit Case Outlines.
HANDBOOKS
DEPARTMENT OF DEFENSE
MIL-HDBK-103 - List of Standard Microcircuit Drawings (SMD's).
MIL-HDBK-780 - Standard Microcircuit Drawings.
(Unless otherwise indicated, copies of the specification, standards, and handbooks are available from the Standardization
Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the
maximum levels may degrade performance and affect reliability.
STANDARD
MICROCI RCUIT DRAWI NG SIZE
A5962-99502
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000 REVISION LEVEL SHEET
4
DSCC FORM 2234
APR 97
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with
MIL-PRF-38535 and as specified herein or as modified in the device manufacturer's Quality Management (QM) plan. The
modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for
device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified
herein.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified
in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M.
3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1.
3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the
electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full
ambient operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are defined in table I.
3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be
marked as listed in MIL-HDBK-103. For packages where marking of the entire SMD PIN number is not feasible due to space
limitations, the manufacturer has the option of not marking the "5962-" on the device. For RHA product using this option, the
RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535.
Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A.
3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a "QML" or "Q" as required in
MIL-PRF-38535. The compliance mark for device class M shall be a "C" as required in MIL-PRF-38535, appendix A.
3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535
listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of
compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see
6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this
drawing shall affirm that the manufacturer's product meets, for device classes Q and V, the requirements of MIL-PRF-38535
and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein.
3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for
device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing.
3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2
herein) involving devices acquired to this drawing is required for any change as defined in MIL-STD-973.
3.9 Verification and review for device class M. For device class M, DSCC, DSCC's agent, and the acquiring activity retain
the option to review the manufacturer's facility and applicable required documentation. Offshore documentation shall be made
available onshore at the option of the reviewer.
3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in
microcircuit group number 49 (see MIL-PRF-38535, appendix A).
STANDARD
MICROCI RCUIT DRAWI NG SIZE
A5962-99502
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000 REVISION LEVEL SHEET
5
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics.
Test Symbol
Conditions 1/
-55
C
TA
+125
C
unless otherwise specified Group A
subgroups Device
type Limits Unit
Min Max
Input offset voltage VOS VS = 5 V 1 01 60
V
2,3 260
VS =
15 V 1 200
2,3 450
Input offset voltage drift
VOS/VS = 5 V 2/ 2,3 01 2.0
V/
C
TV
S
=
15 V 2/ 2.5
Input offset current IOS VS = 5 V and VS =
15 V 101 0.45nA
2,3 0.80
Input bias current IIB VS = 5 V and VS =
15 V 101 11nA
2,3 13
Input voltage range VIN VS = 5 V 1 01 3.5 to
0V
VS =
15 V 13.5
to
-15.0
Maximum output voltage VOM Output low, no load, 1 01 6 mV
swing VS = 5 V 2,3 8
Output low, 2 k
to GND,
VS = 5 V 11.1
Output low, VS = 5 V, 1 130
ISINK = 100
A2,3 170
Output high, no load, 1 4.2 V
VS = 5 V 2,3 3.9
Output high, 2k
to GND, 13.5
V
S
= 5 V 2,3 3.0
VS =
15 V, RL = 50 k
1
13
VS =
15 V, RL = 2 k
11
VS =
15 V, RL = 5 k
2,3
11
Supply current ISVS = 5 V 1 01 68
A
2,3 90
VS =
15 V 185
2,3 105
Offset adjustment range VOSR RPOT = 10 k
, VS = 5 V,
wiper to +VS
101
500
V
Minimum supply voltage VSVS = 5 V 3/ 101 2.3V
See footnotes at end of table.
STANDARD
MICROCI RCUIT DRAWI NG SIZE
A5962-99502
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000 REVISION LEVEL SHEET
6
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics - Continued.
Test Symbol
Conditions 1/
-55
C
TA
+125
C
unless otherwise specified Group A
subgroups Device
type Limits Unit
Min Max
Input resistance, RIN VS = 5 V 2/ 4 01 270 M
differential mode
Common mode rejection CMRR VCM = 0 V to 3.5 V, 4 01 94 dB
ratio VS = 5 V
VCM = 0.05 V to 3.2 V, 5,6 88
VS = 5 V
VCM = +13.5, -15 V, 4 97
VS =
15 V
VCM = +13, -14.9 V, 5,6 90
VS =
15 V
Power supply rejection PSRR VS = 5 V, 2.3 V to 12 V 4 01 100 dB
ratio VS = 5 V, 3.1 V to 12 V 5,6 94
VS = 5 V, 0 V to
18 V 4 103
5,6 97
Large signal voltage gain AVOL VS = 5 V, no load, 4 01 240 V/mV
VOUT = 0.03 V to 4 V
VS = 5 V, RL = 50 k
,200
VOUT = 0.03 V to 3.5 V
VS = 5 V, RL = 50 k
,5,6 100
VOUT = 0.05 V to 3.5 V
VS =
15 V, RL = 50 k
,4 800
VOUT =
10 V
VS =
15 V, RL = 2 k
,300
VOUT =
10 V
VS =
15 V, RL = 5 k
,5,6 250
VOUT =
10 V
Slew rate SR VS = 5 V 4/ 4010.05 V/
s
VS =
15 V 4/ 0.07
1/ Unless otherwise specified, common mode voltage (VCM) = 0.1 V, and output voltage (VOUT) = 1.4 V.
2/ If not tested, shall be guaranteed to the limits specified in table I herein.
3/ Power supply rejection ratio is measured at the minimum supply voltage. The operational amplifiers actually work
at 1.8 V supply but with an average offset skew of -300
V.
4/ Slew rate at 5 V, 0 V is guaranteed by inference from slew rate measurement at
15 V.
STANDARD
MICROCI RCUIT DRAWI NG SIZE
A5962-99502
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000 REVISION LEVEL SHEET
7
DSCC FORM 2234
APR 97
Device type 01
Case outlines G and P
Terminal number Terminal symbol
1V
OS TRIM
2 -INPUT
3 +INPUT
4-V
S
5NC
6 OUTPUT
7+V
S
8V
OS TRIM
FIGURE 1. Terminal connections.
STANDARD
MICROCI RCUIT DRAWI NG SIZE
A5962-99502
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000 REVISION LEVEL SHEET
8
DSCC FORM 2234
APR 97
4. QUALITY ASSURANCE PROVISIONS
4.1 Sampling and inspection. For device classes Q and V, sampling and inspection procedures shall be in accordance with
MIL-PRF-38535 or as modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan
shall not affect the form, fit, or function as described herein. For device class M, sampling and inspection procedures shall be
in accordance with MIL-PRF-38535, appendix A.
4.2 Screening. For device classes Q and V, screening shall be in accordance with MIL-PRF-38535, and shall be conducted
on all devices prior to qualification and technology conformance inspection. For device class M, screening shall be in
accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection.
4.2.1 Additional criteria for device class M.
a. Burn-in test, method 1015 of MIL-STD-883.
(1) Test condition C. The test circuit shall be maintained by the manufacturer under document revision level control
and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the
inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test
method 1015.
(2) TA = +125
C, minimum.
b. Interim and final electrical test parameters shall be as specified in table II herein.
4.2.2 Additional criteria for device classes Q and V.
a. The burn-in test duration, test condition and test temperature, or approved alternatives shall be as specified in the
device manufacturer's QM plan in accordance with MIL-PRF-38535. The burn-in test circuit shall be maintained under
document revision level control of the device manufacturer's Technology Review Board (TRB) in accordance with
MIL-PRF-38535 and shall be made available to the acquiring or preparing activity upon request. The test circuit shall
specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test
method 1015 of MIL-STD-883.
b. Interim and final electrical test parameters shall be as specified in table II herein.
c. Additional screening for device class V beyond the requirements of device class Q shall be as specified in
MIL-PRF-38535, appendix B.
4.3 Qualification inspection for device classes Q and V. Qualification inspection for device classes Q and V shall be in
accordance with MIL-PRF-38535. Inspections to be performed shall be those specified in MIL-PRF-38535 and herein for
groups A, B, C, D, and E inspections (see 4.4.1 through 4.4.4).
4.4 Conformance inspection. Technology conformance inspection for classes Q and V shall be in accordance with
MIL-PRF-38535 including groups A, B, C, D, and E inspections and as specified herein except where option 2 of
MIL-PRF-38535 permits alternate in-line control testing. Quality conformance inspection for device class M shall be in
accordance with MIL-PRF-38535, appendix A and as specified herein. Inspections to be performed for device class M shall be
those specified in method 5005 of MIL-STD-883 and herein for groups A, B, C, D, and E inspections (see 4.4.1 through 4.4.4).
4.4.1 Group A inspection.
a. Tests shall be as specified in table II herein.
b. Subgroups 7, 8, 9, 10, and 11 in table I, method 5005 of MIL-STD-883 shall be omitted..
STANDARD
MICROCI RCUIT DRAWI NG SIZE
A5962-99502
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000 REVISION LEVEL SHEET
9
DSCC FORM 2234
APR 97
TABLE II. Electrical test requirements.
Test requirements Subgroups
(in accordance with
MIL-STD-883,
method 5005, table I)
Subgroups
(in accordance with
MIL-PRF-38535, table III)
Device
class M Device
class Q Device
class V
Interim electrical
parameters (see 4.2) 1,4 1,4 1,4
Final electrical
parameters (see 4.2) 1,2,3,4,5,6 1/ 1,2,3,4,5,6 1/ 1,2,3,4,5,6 1/
Group A test
requirements (see 4.4) 1,2,3,4,5,6 1,2,3,4,5,6 1,2,3,4,5,6
Group C end-point electrical
parameters (see 4.4) 1,2,3,4,5,6 1,2,3,4,5,6 1,2,3,4,5,6
Group D end-point electrical
parameters (see 4.4) 1,2,3,4,5,6 1,2,3,4,5,6 1,2,3,4,5,6
Group E end-point electrical
parameters (see 4.4) --- --- ---
1/ PDA applies to subgroup 1.
4.4.2 Group C inspection. The group C inspection end-point electrical parameters shall be as specified in table II herein.
4.4.2.1 Additional criteria for device class M. Steady-state life test conditions, method 1005 of MIL-STD-883:
a. Test condition C. The test circuit shall be maintained by the manufacturer under document revision level control and
shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs,
outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test method 1005 of
MIL-STD-883.
b. TA = +125
C, minimum.
c. Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883.
4.4.2.2 Additional criteria for device classes Q and V. The steady-state life test duration, test condition and test temperature,
or approved alternatives shall be as specified in the device manufacturer's QM plan in accordance with MIL-PRF-38535. The
test circuit shall be maintained under document revision level control by the device manufacturer's TRB in accordance with
MIL-PRF-38535 and shall be made available to the acquiring or preparing activity upon request. The test circuit shall specify
the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test method 1005 of
MIL-STD-883.
4.4.3 Group D inspection. The group D inspection end-point electrical parameters shall be as specified in table II herein.
STANDARD
MICROCI RCUIT DRAWI NG SIZE
A5962-99502
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000 REVISION LEVEL SHEET
10
DSCC FORM 2234
APR 97
4.4.4 Group E inspection. Group E inspection is required only for parts intended to be marked as radiation hardness
assured (see 3.5 herein).
a. End-point electrical parameters shall be as specified in table II herein.
b. For device classes Q and V, the devices or test vehicle shall be subjected to radiation hardness assured tests as
specified in MIL-PRF-38535 for the RHA level being tested. For device class M, the devices shall be subjected to
radiation hardness assured tests as specified in MIL-PRF-38535, appendix A for the RHA level being tested. All
device classes must meet the postirradiation end-point electrical parameter limits as defined in table I at
TA = +25
C
5
C, after exposure, to the subgroups specified in table II herein.
c. When specified in the purchase order or contract, a copy of the RHA delta limits shall be supplied.
5. PACKAGING
5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535 for device
classes Q and V or MIL-PRF-38535, appendix A for device class M.
6. NOTES
6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications
(original equipment), design applications, and logistics purposes.
6.1.1 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor
prepared specification or drawing.
6.1.2 Substitutability. Device class Q devices will replace device class M devices.
6.2 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated with the users of record for
the individual documents. This coordination will be accomplished in accordance with MIL-STD-973 using DD Form 1692,
Engineering Change Proposal.
6.3 Record of users. Military and industrial users should inform Defense Supply Center Columbus when a system
application requires configuration control and which SMD's are applicable to that system. DSCC will maintain a record of users
and this list will be used for coordination and distribution of changes to the drawings. Users of drawings covering
microelectronic devices (FSC 5962) should contact DSCC-VA, telephone (614) 692-0525.
6.4 Comments. Comments on this drawing should be directed to DSCC-VA , Columbus, Ohio 43216-5000, or telephone
(614) 692-0674.
6.5 Abbreviations, symbols, and definitions. The abbreviations, symbols, and definitions used herein are defined in
MIL-PRF-38535 and MIL-HDBK-1331.
6.6 Sources of supply.
6.6.1 Sources of supply for device classes Q and V. Sources of supply for device classes Q and V are listed in QML-38535.
The vendors listed in QML-38535 have submitted a certificate of compliance (see 3.6 herein) to DSCC-VA and have agreed to
this drawing.
6.6.2 Approved sources of supply for device class M. Approved sources of supply for class M are listed in MIL-HDBK-103.
The vendors listed in MIL-HDBK-103 have agreed to this drawing and a certificate of compliance (see 3.6 herein) has been
submitted to and accepted by DSCC-VA.
STANDARD MICROCIRCUIT DRAWING BUL LETIN
DATE: 98-11-05
Approved sources of supply for SMD 5962-99502 are listed below for immediate acquisition information only and
shall be added to MIL-HDBK-103 and QML-38535 during the next revision. MIL-HDBK-103 and QML-38535 will be
revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a
certificate of compliance has been submitted to and accepted by DSCC-VA. This bulletin is superseded by the next
dated revision of MIL-HDBK-103 and QML-38535
Standard
microcircuit drawing
PIN 1/
Vendor
CAGE
number
Vendor
similar
PIN 2/
5962-9950201QGA 64155 LT1077MH8
5962-9950201QPA 64155 LT1077MJ8
1/ The lead finish shown for each PIN representing
a hermetic package is the most readily available
from the manufacturer listed for that part. If the
desired lead finish is not listed, contact the vendor
to determine its availability.
2/ Caution. Do not use this number for item
acquisition. Items acquired to this number may not
satisfy the performance requirements of this drawing.
Vendor CAGE Vendor name
number and address
64155 Linear Technology Corporation
1630 McCarthy Boulevard
Milpitas, CA 95035-7487
The information contained herein is disseminated for convenience only and the
Government assumes no liability whatsoever for any inaccuracies in the
information bulletin.
