Primary lithium battery LS 14250W 3.6 V Primary lithium-thionyl chloride (Li-SOCl2) High energy density 1 2 AA-size bobbin cell For demanding environments up to + 95C For applications requesting superior voltage response and operating life in Widely fluctuating temperature environments up to + 95C. Benefits l High 1/2 R6 - 1/2 AA Cell size references voltage, stable during most of the application's lifetime l Superior voltage readings after exposure at elevated temperature l Voltage readings during pulsing moderately affected by T fluctuations l Low self-discharge rate (less than 1 % per year of storage at + 20C) l Easy integration into compact systems l Superior resistance to atmospheric corrosion Pulse capability : Typically up to 100 mA (100 mA/0.1 second pulses, drained every 2 mn at + 20C from undischarged cells with 10 A base current, yield voltage readings above 3.0 V. The readings may vary according to the pulse characteristics, the temperature, and the cell's previous history. Fitting the cell with a capacitor may be recommended in severe conditions. Consult Saft) Key features Maximum recommended continuous current (Higher currents are possible, consult Saft) l Stainless Storage l l l steel container and end caps (low magnetic signature) Hermetic glass-to-metal sealing Non-flammable electrolyte Non-restricted for transport Main applications l l l l l l l Electronic toll collection Utility metering Automatic meter reading Alarms and security devices Tracking systems Automotive electronics Professional electronics June 2008 Electrical characteristics (typical values relative to cells stored for one year or less at + 30C max.) Nominal capacity 1.20 Ah (at 1 mA + 20C 2.0 V cut-off. The capacity restored by the cell varies according to current drain, temperature and cut-off) Open circuit voltage (at + 20C) 3.67 V Nominal voltage (at 0.1 mA + 20C) 3.6 V 35 mA (recommended) (for more severe conditions, consult Saft) Operating temperature range (Operation above ambient T may lead to reduced capacity and lower voltage readings at the beginning of pulses. Consult Saft) + 30C (+ 86F) max - 60C/+ 95C (- 76F/+ 203F) Physical characteristics Diameter (max) 14.65 mm (0.58 in) Height (max) 24.8 mm (0.98 in) Typical weight 8.9 g (0.3 oz) Li metal content approx. 0.3 g Available termination suffix CN, CNR 2 PF, 3 PF, 3 PF RP, 4 PF CNA (AX) FL radial tabs radial pins axial leads flying leads ...etc. LS 14250W Cell voltage (V) Voltage plateau versus Current and Temperature (at mid-discharge) Current (mA) Dimensions in mm. Cell voltage (V) Typical discharge profiles at + 20C Time (hours) Storage Warning l Fire, explosion and burn hazard. not recharge, short circuit, crush, disassemble, heat above 100C (212F), incinerate, or expose contents to water. l Do not solder directly to the cell (use tabbed cell versions instead). l Do Saft Specialty Battery Group 1.35 0.2 12, rue Sadi Carnot 93170 Bagnolet - France Tel.: +33 (0)1 49 93 19 18 Fax: +33 (0)1 49 93 19 69 www.saftbatteries.com Capacity (mAh) storage area should be clean, cool (preferably not exceeding + 30C), dry and ventilated. Restored Capacity versus Current and Temperature (2.0 V cut-off) l The Current (mA) Doc. N 31087-2-0608 Information in this document is subject to change without notice and becomes contractual only after written confirmation by Saft. For more details on primary lithium technologies please refer to Primary Lithium Batteries Selector Guide Doc No 31048-2. Published by the Communications Department Photo credit: Saft Societe anonyme au capital de 31 944 000 RCS Bobigny B 383 703 873 Produced by Arthur Associates Limited.