AM26LS31CDRE4 - TEXAS INSTRUMENTS

POWER-ON

RESET

DAC

INPUT

CONTROL

LOGIC

POWER-DOWN

CONTROL

LOGIC

VREFIN

DAC104S085

VOUTA

10 BIT DAC

REF

SCLK DIN

SYNC

BUFFER

VOUTB

VOUTC

VOUTD

2.5k 100k

10 BIT DAC

REF

10 BIT DAC

REF

10 BIT DAC

REF

Product

Folder

Sample &

Buy

Technical

Documents

Tools &

Software

Support &

Community

An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,

intellectual property matters and other important disclaimers. PRODUCTION DATA.

DAC104S085

DAC104S085-Q1

SNAS362G –MAY 2006–REVISED APRIL 2016

DAC104S085-xx 10-Bit Micro Power QUAD Digital-to-Analog Converter With Rail-to-Rail

Output

1 Features

1• Qualified for Automotive Applications

• AEC-Q100 Qualified With the Following Results:

– Device Temperature Grade 1: –40°C to 125°C

Ambient Operating Temperature

• Ensured Monotonicity

• Low Power Operation

• Rail-to-Rail Voltage Output

• Power-On Reset to 0 V

• Simultaneous Output Updating

• Wide Power Supply Range (2.7 V to 5.5 V)

• Key Specifications

– Resolution: 10 bits

– INL: ±2 LSB (Maximum)

– DNL: +0.35 / −0.25 LSB (Maximum)

– Settling Time: 6 μs (Maximum)

– Zero Code Error: 15 mV (Maximum)

– Full-Scale Error: −0.75% FS (Maximum)

– Typical Supply Power

– Normal Mode: 1.1 mW (3 V), 2.5 mW (5 V)

– Power Down: 0.3 μW (3 V), 0.8 μW (5 V)

2 Applications

• Battery-Powered Instruments

• Digital Gain and Offset Adjustment

• Programmable Voltage and Current Sources

• Programmable Attenuators

• Automotives

3 Description

The DAC104S085 device is a full-featured, general-

purpose QUAD 10-bit voltage-output digital-to-analog

converter (DAC) that can operate from a single 2.7-V

to 5.5-V supply and consumes 1.1 mW at 3 V and

2.5 mW at 5 V. The DAC104S085 is packaged in 10-

pin SON and VSSOP packages. The 10-pin SON

package makes the DAC104S085 the smallest QUAD

DAC in its class. The on-chip output amplifier allows

rail-to-rail output swing and the three wire serial

interface operates at clock rates up to 40 MHz over

the entire supply voltage range. Competitive devices

are limited to 25-MHz clock rates at supply voltages

in the 2.7-V to 3.6-V range. The serial interface is

compatible with standard SPI, QSPI, MICROWIRE,

and DSP interfaces.

The reference for the DAC104S085 serves all four

channels and can vary in voltage between 1 V and

VA, providing the widest possible output dynamic

range. The DAC104S085 has a 16-bit input shift

mode of operation, the power-down condition, and

the binary input data. All four outputs can be updated

simultaneously or individually depending on the

setting of the two mode of operation bits.

Device Information(1)

PART NUMBER PACKAGE BODY SIZE (NOM)

DAC104S085-xx VSSOP (10) 3.00 mm × 3.00 mm

WSON (10) 3.00 mm × 3.00 mm

(1) For all available packages, see the orderable addendum at

the end of the data sheet.

Block Diagram

DAC104S085

DAC104S085-Q1

SNAS362G –MAY 2006–REVISED APRIL 2016

www.ti.com

Product Folder Links: DAC104S085 DAC104S085-Q1

Table of Contents

1 Features.................................................................. 1

2 Applications ........................................................... 1

3 Description............................................................. 1

4 Revision History..................................................... 2

5 Description (continued)......................................... 3

6 Pin Configuration and Functions......................... 3

7 Specifications......................................................... 4

7.1 Absolute Maximum Ratings ..................................... 4

7.2 ESD Ratings – DAC104S085 ................................... 4

7.3 ESD Ratings – DAC104S085-Q1 ............................. 4

7.4 Recommended Operating Conditions....................... 4

7.5 Thermal Information.................................................. 5

7.6 Electrical Characteristics........................................... 5

7.7 Timing Requirements................................................ 7

7.8 Typical Characteristics.............................................. 9

8 Detailed Description............................................ 13

8.1 Overview................................................................. 13

8.2 Functional Block Diagram....................................... 14

8.3 Feature Description................................................. 14

8.4 Device Functional Modes........................................ 15

8.5 Programming........................................................... 16

9 Application and Implementation ........................ 19

9.1 Application Information............................................ 19

9.2 Typical Application ................................................. 21

10 Power Supply Recommendations ..................... 22

11 Layout................................................................... 23

11.1 Layout Guidelines ................................................. 23

11.2 Layout Example .................................................... 23

12 Device and Documentation Support................. 24

12.1 Device Support...................................................... 24

12.2 Related Links ........................................................ 25

12.3 Community Resources.......................................... 25

12.4 Trademarks........................................................... 25

12.5 Electrostatic Discharge Caution............................ 25

12.6 Glossary................................................................ 25

13 Mechanical, Packaging, and Orderable

Information........................................................... 25

4 Revision History

NOTE: Page numbers for previous revisions may differ from page numbers in the current version.

Changes from Revision F (March 2013) to Revision G Page

• Added ESD Ratings table, Feature Description section, Device Functional Modes,Application and Implementation

section, Power Supply Recommendations section, Layout section, Device and Documentation Support section, and

Mechanical, Packaging, and Orderable Information section.................................................................................................. 1

Changes from Revision E (March 2013) to Revision F Page

• Changed layout of National Data Sheet to TI format ........................................................................................................... 23

VOUTA

VOUTB

VOUTD

VOUTC

SCLK

DIN

VREFIN

GND

SYNC

VSSOP

VOUTA

VOUTB

VOUTD

VOUTC

SCLK

DIN

VREFIN

GND

SON

SYNC

DAC104S085

DAC104S085-Q1

www.ti.com

SNAS362G –MAY 2006–REVISED APRIL 2016

Product Folder Links: DAC104S085 DAC104S085-Q1

5 Description (continued)

A power-on reset circuit ensures that the DAC output powers up to zero volts and remains there until there is a

valid write to the device. A power-down feature reduces power consumption to less than a microWatt with three

different termination options.

The low power consumption and small packages of the DAC104S085 make it an excellent choice for use in

battery-operated equipment.

The DAC104S085 is one of a family of pin-compatible DACs, including the 8-bit DAC084S085 and the 12-bit

DAC124S085. The DAC104S085 operates over the extended industrial temperature range of −40°C to +125°C.

6 Pin Configuration and Functions

DSC Package

10-Pin SON

Top View DGS Package

10-Pin VSSOP

Top View

Pin Functions

PIN TYPE DESCRIPTION

NO. NAME

1 VASupply Power supply input. Must be decoupled to GND.

2 VOUTA Analog Output Channel A Analog Output Voltage.

3 VOUTB Analog Output Channel B Analog Output Voltage.

4 VOUTC Analog Output Channel C Analog Output Voltage.

5 VOUTD Analog Output Channel D Analog Output Voltage.

6 GND Ground Ground reference for all on-chip circuitry.

7 VREFIN Analog Input Unbuffered reference voltage shared by all channels. Must be decoupled

to GND.

8 DIN Digital Input Serial Data Input. Data is clocked into the 16-bit shift register on the

falling edges of SCLK after the fall of SYNC.

9 SYNC Digital Input

Frame synchronization input for the data input. When this pin goes low, it

enables the input shift register and data is transferred on the falling edges

of SCLK. The DAC is updated on the 16th clock cycle unless SYNC is

brought high before the 16th clock, in which case the rising edge of

SYNC acts as an interrupt and the write sequence is ignored by the DAC.

10 SCLK Digital Input Serial Clock Input. Data is clocked into the input shift register on the

falling edges of this pin.

11 PAD

(SON only) Ground Exposed die attach pad can be connected to ground or left floating.

Soldering the pad to the PCB offers optimal thermal performance and

enhances package self-alignment during reflow.

I/O

GND

TO INTERNAL

CIRCUITRY

DAC104S085

DAC104S085-Q1

SNAS362G –MAY 2006–REVISED APRIL 2016

www.ti.com

Product Folder Links: DAC104S085 DAC104S085-Q1

(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings

only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended

Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.

(2) All voltages are measured with respect to GND = 0 V, unless otherwise specified.

(3) If Military/Aerospace specified devices are required, please contact the TI Sales Office/Distributors for availability and specifications.

(4) When the input voltage at any pin exceeds 5.5 V or is less than GND, the current at that pin should be limited to 10 mA. The 20 mA

maximum package input current rating limits the number of pins that can safely exceed the power supplies with an input current of 10

mA to two.

(5) The absolute maximum junction temperature (TJmax) for this device is 150°C. The maximum allowable power dissipation is dictated by

TJmax, the junction-to-ambient thermal resistance (θJA), and the ambient temperature (TA), and can be calculated using the formula

PDMAX = (TJmax −TA) / θJA. The values for maximum power dissipation is reached only when the device is operated in a severe fault

condition (that is, when input or output pins are driven beyond the operating ratings, or the power supply polarity is reversed).

7 Specifications

7.1 Absolute Maximum Ratings (1)(2)(3)

MIN MAX UNIT

Supply voltage, VA6.5 V

Voltage on any input pin −0.3 6.5 V

Input current at any pin(4) 10 mA

Package input current(4) 20 mA

Power consumption at TA= 25°C See (5)

Junction temperature 150 °C

Storage temperature, Tstg −65 150 °C

(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.

(2) Human body model is 100-pF capacitor discharged through a 1.5-kΩresistor. Machine model is 220 pF discharged through 0 Ω.

7.2 ESD Ratings – DAC104S085 VALUE UNIT

V(ESD) Electrostatic discharge Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1)(2) ±2500 V

Machine model (MM) ±250

(1) AEC Q100-002 indicates that HBM stressing shall be in accordance with the ANSI/ESDA/JEDEC JS-001 specification.

7.3 ESD Ratings – DAC104S085-Q1 VALUE UNIT

V(ESD) Electrostatic discharge Human-body model (HBM), per AEC Q100-002(1) ±2500 V

(1) All voltages are measured with respect to GND = 0 V, unless otherwise specified.

(2) The inputs are protected as shown. Input voltage magnitudes up to 5.5 V, regardless of VA, does not cause errors in the conversion

result. For example, if VAis 3 V, the digital input pins can be driven with a 5-V logic device.

7.4 Recommended Operating Conditions(1)

MIN MAX UNIT

Operating temperature –40 125 °C

Supply voltage, VA2.7 5.5 V

Reference voltage, VREFIN 1 VAV

Digital input voltage(2) 0 5.5 V

Output load 0 1500 pF

DAC104S085

DAC104S085-Q1

www.ti.com

SNAS362G –MAY 2006–REVISED APRIL 2016

Product Folder Links: DAC104S085 DAC104S085-Q1

Recommended Operating Conditions(1) (continued)

MIN MAX UNIT

SCLK frequency 40 MHz

(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application

report, SPRA953.

(2) Soldering process must comply with Reflow Temperature Profile specifications. See the Absolute Maximum Ratings for Soldering

application report, SNOA549, for more information.

(3) Reflow temperature profiles are different for lead-free packages.

7.5 Thermal Information

THERMAL METRIC(1)(2)(3) DAC104S085-xx

UNITDGS (VSSOP) DSC (SON)

10 PINS 10 PINS

RθJA Junction-to-ambient thermal resistance 159 48.9 °C/W

RθJC(top) Junction-to-case (top) thermal resistance 53.3 40.7 °C/W

RθJB Junction-to-board thermal resistance 78.9 23.7 °C/W

ψJT Junction-to-top characterization parameter 4.8 0.4 °C/W

ψJB Junction-to-board characterization parameter 77.6 23.8 °C/W

RθJC(bot) Junction-to-case (bottom) thermal resistance N/A 4.7 °C/W

(1) Typical figures are at TJ= 25°C, and represent most likely parametric norms. Test limits are specified to TI's AOQL (Average Outgoing

Quality Level).

(2) This parameter is ensured by design and/or characterization and is not tested in production.

7.6 Electrical Characteristics

The following specifications apply for VA= 2.7 V to 5.5 V, VREFIN = VA, CL= 200 pF to GND, fSCLK = 30 MHz, input code range

from 12 to 1011. All limits are at TA= 25°C, unless otherwise specified.

PARAMETER TEST CONDITIONS MIN(1) TYP(1) MAX(1) UNIT

STATIC PERFORMANCE

Resolution TMIN ≤TA≤TMAX 10 Bits

Monotonicity TMIN ≤TA≤TMAX 10 Bits

INL Integral non-linearity ±0.7 LSB

TMIN ≤TA≤TMAX ±2

DNL Differential non-linearity VA= 2.7 V to 5.5 V −0.03 0.08 LSB

TMIN ≤TA≤TMAX −0.25 0.35

ZE Zero code error IOUT = 0 mA 5mV

TMIN ≤TA≤TMAX 15

FSE Full-scale error IOUT = 0 mA −0.1 %FSR

TMIN ≤TA≤TMAX −0.75

GE Gain error All ones Loaded to

DAC register

−0.2 %FSR

TMIN ≤TA≤TMAX −1

ZCED Zero code error drift −20 µV/°C

TC GE Gain error tempco VA= 3 V −0.7 ppm/°C

VA= 5 V −1

OUTPUT CHARACTERISTICS

Output voltage range See(2), TMIN ≤TA≤TMAX 0

VREFIN 0

VREFIN V

IOZ High-impedance output

leakage current(2) TMIN ≤TA≤TMAX ±1 µA

ZCO Zero code output

VA= 3 V, IOUT = 200 µA 1.3

VA= 3 V, IOUT = 1 mA 6

VA= 5 V, IOUT = 200 µA 7

VA= 5 V, IOUT = 1 mA 10

DAC104S085

DAC104S085-Q1

SNAS362G –MAY 2006–REVISED APRIL 2016

www.ti.com

Product Folder Links: DAC104S085 DAC104S085-Q1

Electrical Characteristics (continued)

The following specifications apply for VA= 2.7 V to 5.5 V, VREFIN = VA, CL= 200 pF to GND, fSCLK = 30 MHz, input code range

from 12 to 1011. All limits are at TA= 25°C, unless otherwise specified.

PARAMETER TEST CONDITIONS MIN(1) TYP(1) MAX(1) UNIT

(3) To ensure accuracy, it is required that VAand VREFIN be well bypassed.

FSO Full-scale output

VA= 3 V, IOUT = 200 µA 2.984

VA= 3 V, IOUT = 1 mA 2.934

VA= 5 V, IOUT = 200 µA 4.989

VA= 5 V, IOUT = 1 mA 4.958

IOS Output short-circuit current

(source)

VA= 3 V, VOUT = 0 V,

Input Code = 3FFh –56 mA

VA= 5 V, VOUT = 0 V,

Input Code = 3FFh –69

IOS Output short-circuit current

(sink)

VA= 3 V, VOUT = 3 V,

Input Code = 000h 52 mA

VA= 5 V, VOUT = 5 V,

Input Code = 000h 75

IOContinuous output

current(2) Available on each DAC output, TMIN ≤TA≤TMAX 11 mA

CLMaximum load capacitance RL=∞1500 pF

RL= 2 kΩ1500

ZOUT DC output impedance 7.5 Ω

REFERENCE INPUT CHARACTERISTICS

VREFIN

Input range minimum 0.2 V

TMIN ≤TA≤TMAX 1

Input range maximum TMIN ≤TA≤TMAX VAV

Input impedance 30 kΩ

LOGIC INPUT CHARACTERISTICS

IIN Input current(2) TMIN ≤TA≤TMAX ±1 µA

VIL Input low voltage(2) VA= 3 V 0.9 V

TMIN ≤TA≤TMAX 0.6

VA= 5 V 1.5 V

TMIN ≤TA≤TMAX 0.8

VIH Input high voltage(2) VA= 3 V 1.4 V

TMIN ≤TA≤TMAX 2.1

VA= 5 V 2.1 V

TMIN ≤TA≤TMAX 2.4

CIN Input capacitance(2) TMIN ≤TA≤TMAX 3 pF

POWER REQUIREMENTS

VA(3) Supply voltage minimum TMIN ≤TA≤TMAX 2.7 V

Supply voltage maximum TMIN ≤TA≤TMAX 5.5 V

INNormal supply current (output

unloaded)

fSCLK = 30 MHz

VA= 2.7 V

to 3.6 V 350 µA

TMIN ≤TA≤TMAX 485

VA= 4.5 V

to 5.5 V 500 µA

TMIN ≤TA≤TMAX 650

fSCLK = 0 MHz

VA= 2.7 V

to 3.6 V 330 µA

VA= 4.5 V

to 5.5 V 460 µA

IPD

Power-down supply current

(output unloaded, SYNC =

DIN = 0V after PD mode

loaded)

All PD Modes,(2)

VA= 2.7 V

to 3.6 V 0.1 µA

TMIN ≤TA≤TMAX 1

VA= 4.5 V

to 5.5 V 0.15 µA

TMIN ≤TA≤TMAX 1

DAC104S085

DAC104S085-Q1

www.ti.com

SNAS362G –MAY 2006–REVISED APRIL 2016

Product Folder Links: DAC104S085 DAC104S085-Q1

Electrical Characteristics (continued)

The following specifications apply for VA= 2.7 V to 5.5 V, VREFIN = VA, CL= 200 pF to GND, fSCLK = 30 MHz, input code range

from 12 to 1011. All limits are at TA= 25°C, unless otherwise specified.

PARAMETER TEST CONDITIONS MIN(1) TYP(1) MAX(1) UNIT

PNNormal supply power (output

unloaded)

fSCLK = 30 MHz

VA= 2.7 V

to 3.6 V 1.1 mW

TMIN ≤TA≤TMAX 1.7

VA= 4.5 V

to 5.5 V 2.5 mW

TMIN ≤TA≤TMAX 3.6

fSCLK = 0 MHz

VA= 2.7 V

to 3.6 V 1 mW

VA= 4.5 V

to 5.5 V 2.3 mW

PPD

Power-down supply power

(output unloaded, SYNC =

DIN = 0V after PD mode

loaded)

All PD Modes,(2)

VA= 2.7 V

to 3.6 V 0.3 µW

TMIN ≤TA≤TMAX 3.6

VA= 4.5 V

to 5.5 V 0.8 µW

TMIN ≤TA≤TMAX 5.5

(1) Typical figures are at TJ= 25°C, and represent most likely parametric norms. Test limits are specified to TI's AOQL (Average Outgoing

Quality Level).

(2) This parameter is ensured by design and/or characterization and is not tested in production.

7.7 Timing Requirements

Values shown in this table are design targets and are subject to change before product release.

The following specifications apply for VA= 2.7 V to 5.5 V, VREFIN = VA, CL= 200 pF to GND, fSCLK = 30 MHz, input code range

from 12 to 1011. All limits are at TA= 25°C, unless otherwise specified. MIN(1) TYP(1) MAX(1) UNIT

fSCLK SCLK frequency 40 MHz

TMIN ≤TA≤TMAX 30

tsOutput voltage settling time(2) 100h to 300h code

change

RL= 2 kΩ, CL= 200

4.5

µs

TMIN ≤TA≤TMAX 6

SR Output slew rate 1 V/µs

Glitch impulse Code change from 200h to 1FFh 12 nV-sec

Digital feedthrough 0.5 nV-sec

Digital crosstalk 1 nV-sec

DAC-to-DAC crosstalk 3 nV-sec

Multiplying bandwidth VREFIN = 2.5 V ± 0.1 Vpp 160 kHz

Total harmonic distortion VREFIN = 2.5 V ± 0.1 Vpp

input frequency = 10 kHz 70 dB

tWU Wake-up time VA= 3 V 6 µsec

VA= 5 V 39 µsec

1/fSCLK SCLK cycle time 25 ns

TMIN ≤TA≤TMAX 33

tCH SCLK high time 7ns

TMIN ≤TA≤TMAX 10

tCL SCLK low Time 7ns

TMIN ≤TA≤TMAX 10

tSS SYNC set-up time prior to SCLK falling

edge 4ns

TMIN ≤TA≤TMAX 10

tDS Data set-up time prior to SCLK falling

edge 1.5 ns

TMIN ≤TA≤TMAX 3.5

tDH Data hold time after SCLK falling edge 1.5 ns

TMIN ≤TA≤TMAX 3.5

tCFSR SCLK fall prior to rise of SYNC 0ns

TMIN ≤TA≤TMAX 3

OUTPUT

VOLTAGE

DIGITAL INPUT CODE

00 1024

FSE

GE = FSE - ZE

FSE = GE + ZE

1023 x VREFIN

1024

DB15 DB0

SCLK

DIN

SYNC

tSYNC

tDS

tDH

tCL tCH

1 / fSCLK

tCFSR

1 2 13 14 15 16

tSS

DAC104S085

DAC104S085-Q1

SNAS362G –MAY 2006–REVISED APRIL 2016

www.ti.com

Product Folder Links: DAC104S085 DAC104S085-Q1

Timing Requirements (continued)

Values shown in this table are design targets and are subject to change before product release.

The following specifications apply for VA= 2.7 V to 5.5 V, VREFIN = VA, CL= 200 pF to GND, fSCLK = 30 MHz, input code range

from 12 to 1011. All limits are at TA= 25°C, unless otherwise specified. MIN(1) TYP(1) MAX(1) UNIT

tSYNC SYNC high time 6ns

TMIN ≤TA≤TMAX 10

Figure 1. Serial Timing Diagram

Input / Output Transfer Characteristic

DAC104S085

DAC104S085-Q1

www.ti.com

SNAS362G –MAY 2006–REVISED APRIL 2016

Product Folder Links: DAC104S085 DAC104S085-Q1

7.8 Typical Characteristics

VREF = VA, fSCLK = 30 MHz, TA= 25°C, Input Code Range from 12 to 1011, unless otherwise stated

Figure 2. INL at VA= 3 V Figure 3. INL at VA= 5 V

Figure 4. DNL at VA= 3 V Figure 5. DNL at VA= 5 V

Figure 6. INL/DNL vs VREFIN at VA= 3 V Figure 7. INL/DNL vs VREFIN at VA= 5 V

DAC104S085

DAC104S085-Q1

SNAS362G –MAY 2006–REVISED APRIL 2016

www.ti.com

Product Folder Links: DAC104S085 DAC104S085-Q1

Typical Characteristics (continued)

VREF = VA, fSCLK = 30 MHz, TA= 25°C, Input Code Range from 12 to 1011, unless otherwise stated

Figure 8. INL/DNL vs fSCLK at VA= 2.7 V Figure 9. INL/DNL vs VA

Figure 10. INL/DNL vs Clock Duty Cycle at VA= 3 V Figure 11. INL/DNL vs Clock Duty Cycle at VA= 5 V

Figure 12. INL/DNL vs Temperature at VA= 3 V Figure 13. INL/DNL vs Temperature at VA= 5 V

DAC104S085

DAC104S085-Q1

www.ti.com

SNAS362G –MAY 2006–REVISED APRIL 2016

Product Folder Links: DAC104S085 DAC104S085-Q1

Typical Characteristics (continued)

VREF = VA, fSCLK = 30 MHz, TA= 25°C, Input Code Range from 12 to 1011, unless otherwise stated

Figure 14. Zero Code Error vs VAFigure 15. Zero Code Error vs. VREFIN

Figure 16. Zero Code Error vs fSCLK Figure 17. Zero Code Error vs Clock Duty Cycle

Figure 18. Zero Code Error vs Temperature Figure 19. Full-Scale Error vs VA

DAC104S085

DAC104S085-Q1

SNAS362G –MAY 2006–REVISED APRIL 2016

www.ti.com

Product Folder Links: DAC104S085 DAC104S085-Q1

Typical Characteristics (continued)

VREF = VA, fSCLK = 30 MHz, TA= 25°C, Input Code Range from 12 to 1011, unless otherwise stated

Figure 20. Full-Scale Error vs VREFIN Figure 21. Full-Scale Error vs fSCLK

Figure 22. Full-Scale Error vs Clock Duty Cycle Figure 23. Full-Scale Error vs Temperature

Figure 24. Supply Current vs VAFigure 25. Supply Current vs Temperature

To Output Amplifier

DAC104S085

DAC104S085-Q1

www.ti.com

SNAS362G –MAY 2006–REVISED APRIL 2016

Product Folder Links: DAC104S085 DAC104S085-Q1

8 Detailed Description

8.1 Overview

The DAC104S085 is fabricated on a CMOS process with an architecture that consists of switches and resistor

strings that are followed by an output buffer. The reference voltage is externally applied at VREFIN and is shared

by all four DACs.

For simplicity, Figure 26 shows a single resistor string. This string consists of 1024 equal valued resistors with a

switch at each junction of two resistors, plus a switch to ground. The code loaded into the DAC register

determines which switch is closed, connecting the proper node to the amplifier. The input coding is straight

binary with an ideal output voltage found in Equation 1:

VOUTA,B,C,D = VREFIN × (D / 1024)

where

•Dis the decimal equivalent of the binary code that is loaded into the DAC register. D can take on any value

between 0 and 1023. This configuration ensures that the DAC is monotonic. (1)

Figure 26. DAC Resistor String

POWER-ON

RESET

DAC

INPUT

CONTROL

LOGIC

POWER-DOWN

CONTROL

LOGIC

VREFIN

DAC104S085

VOUTA

10 BIT DAC

REF

SCLK DIN

SYNC

BUFFER

VOUTB

VOUTC

VOUTD

2.5k 100k

10 BIT DAC

REF

10 BIT DAC

REF

10 BIT DAC

REF

DAC104S085

DAC104S085-Q1

SNAS362G –MAY 2006–REVISED APRIL 2016

www.ti.com

Product Folder Links: DAC104S085 DAC104S085-Q1

8.2 Functional Block Diagram

8.3 Feature Description

8.3.1 Output Amplifiers

The output amplifiers are rail-to-rail, providing an output voltage range of 0 V to VAwhen the reference is VA. All

amplifiers, even rail-to-rail types, exhibit a loss of linearity as the output approaches the supply rails (0 V and VA,

in this case). For this reason, linearity is specified over less than the full output range of the DAC. However, if the

reference is less than VA, there is only a loss in linearity in the lowest codes. The output capabilities of the

amplifier are described in Electrical Characteristics.

The output amplifiers are capable of driving a load of 2 kΩin parallel with 1500 pF to ground or to VA. The zero-

code and full-scale outputs for given load currents are available in Electrical Characteristics.

8.3.2 Reference Voltage

The DAC104S085 uses a single external reference that is shared by all four channels. The reference pin, VREFIN,

is not buffered and has an input impedance of 30 kΩ. TI recommends driving the VREFIN by a voltage source with

low output impedance. The reference voltage range is 1 V to VA, providing the widest possible output dynamic

range.

8.3.3 Power-On Reset

The power-on reset circuit controls the output voltages of the four DACs during power up. Upon application of

power, the DAC registers are filled with zeros and the output voltages are 0 V. The outputs remain at 0 V until a

valid write sequence is made to the DAC.

DAC104S085

DIN

SCLK

SYNC VOUT

0.1 PF

10 PF+

+5V

-5V

+5V

±5V

10 pF

DAC104S085

DAC104S085-Q1

www.ti.com

SNAS362G –MAY 2006–REVISED APRIL 2016

Product Folder Links: DAC104S085 DAC104S085-Q1

8.4 Device Functional Modes

8.4.1 Power-Down Modes

The DAC104S085 has four power-down modes, two of which are identical. In power-down mode, the supply

current drops to 20 µA at 3 V and 30 µA at 5 V. The DAC104S085 is set in power-down mode by setting OP1

and OP0 to 11. Because this mode powers down all four DACs, the address bits, A1 and A0, are used to select

different output terminations for the DAC outputs. Setting A1 and A0 to 00 or 11 causes the outputs to be tri-

stated (a high impedance state). While setting A1 and A0 to 01 or 10 causes the outputs to be terminated by

2.5 kΩor 100 kΩto ground respectively (see Table 1).

Table 1. Power-Down Modes

A1 A0 OP1 OP0 OPERATING MODE

0 0 1 1 High-Z outputs

0 1 1 1 2.5 kΩto GND

1 0 1 1 100 kΩto GND

1 1 1 1 High-Z outputs

The bias generator, output amplifiers, resistor strings, and other linear circuitry are all shut down in any of the

power-down modes. However, the contents of the DAC registers are unaffected when in power down. Each DAC

sequence that instructed it to recover from power down. Minimum power consumption is achieved in the power-

down mode with SYNC and DIN idled low and SCLK disabled. The time to exit power down (Wake-Up Time) is

typically tWU µs as stated in Timing Requirements.

8.4.2 Bipolar Operation

The DAC104S085 is designed for single-supply operation and thus has a unipolar output. However, a bipolar

output may be obtained with the circuit in Figure 27. This circuit provides an output voltage range of ±5 V. A rail-

to-rail amplifier should be used if the amplifier supplies are limited to ±5 V.

Figure 27. Bipolar Operation

The output voltage of this circuit for any code is found in Equation 2 and Equation 3.

VO= (VA× (D / 1024) × ((R1 + R2) / R1) – VA× R2 / R1)

where

• D is the input code in decimal form

• With VA= 5 V and R1 = R2 (2)

MSB

A1 A0 OP1 OP0 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0

DATA BITS

0 0 Write to specified register but do not update outputs.

0 1 Write to specified register and update outputs.

1 0 Write to all registers and update outputs.

1 1 Power-down outputs.

LSB

0 0 DAC A

0 1 DAC B

1 0 DAC C

1 1 DAC D

DAC104S085

DAC104S085-Q1

SNAS362G –MAY 2006–REVISED APRIL 2016

www.ti.com

Product Folder Links: DAC104S085 DAC104S085-Q1

VO= (10 × D / 1024) – 5 V (3)

A list of rail-to-rail amplifiers suitable for this application are indicated in Table 2.

Table 2. Some Rail-to-Rail Amplifiers

AMP PKGS TYP VOS TYP ISUPPLY

LMC7111 DIP-8

SOT23-5 0.9 mV 25 µA

LM7301 SO-8

SOT23-5 0.03 mV 620 µA

LM8261 SOT23-5 0.7 mV 1 mA

8.5 Programming

8.5.1 Serial Interface

The three-wire interface is compatible with SPI, QSPI, and MICROWIRE, as well as most DSPs and operates at

clock rates up to 40 MHz. See the Figure 1 for information on a write sequence.

A write sequence begins by bringing the SYNC line low. Once SYNC is low, the data on the DIN line is clocked

into the 16-bit serial input register on the falling edges of SCLK. To avoid misclocking data into the shift register,

it is critical that SYNC not be brought low simultaneously with a falling edge of SCLK (see Figure 1). On the 16th

falling clock edge, the last data bit is clocked in and the programmed function (a change in the DAC channel

address, mode of operation and/or register contents) is executed. At this point the SYNC line may be kept low or

brought high. Any data and clock pulses after the 16th falling clock edge is ignored. In either case, SYNC must

be brought high for the minimum specified time before the next write sequence is initiated with a falling edge of

SYNC.

Because the SYNC and DIN buffers draw more current when they are high, they must be idled low between write

sequences to minimize power consumption.

8.5.2 Input Shift Register

The input shift register, Figure 28, has sixteen bits. The first two bits are address bits. They determine whether

the register data is for DAC A, DAC B, DAC C, or DAC D. The address bits are followed by two bits that

determine the mode of operation (writing to a DAC register without updating the outputs of all four DACs, writing

to a DAC register and updating the outputs of all four DACs, writing to the register of all four DACs and updating

their outputs, or powering down all four outputs). The final twelve bits of the shift register are the data bits. The

data format is straight binary (MSB first, LSB last), with all 0s corresponding to an output of 0 V and all 1s

corresponding to a full-scale output of VREFIN – 1 LSB. The contents of the serial input register are transferred to

the DAC register on the sixteenth falling edge of SCLK. See Figure 1.

Figure 28. Input Register Contents

Normally, the SYNC line is kept low for at least 16 falling edges of SCLK and the DAC is updated on the 16th

SCLK falling edge. However, if SYNC is brought high before the 16th falling edge, the data transfer to the shift

there is no change in the mode of operation or in the DAC output voltages.

8.5.3 DSP and Microprocessor Interfacing

Interfacing the DAC104S085 to microprocessors and DSPs is quite simple. The following guidelines are offered

to hasten the design process.

68HC11 DAC104S085

PC7

SCK

MOSI

SCLK

DIN

SYNC

80C51/80L51 DAC104S085

P3.3

TXD

RXD

SCLK

DIN

SYNC

ADSP-2101/

ADSP2103 DAC104S085

TFS

SCLK

DIN

SCLK

SYNC

DAC104S085

DAC104S085-Q1

www.ti.com

SNAS362G –MAY 2006–REVISED APRIL 2016

Product Folder Links: DAC104S085 DAC104S085-Q1

Programming (continued)

8.5.3.1 ADSP-2101 and ADSP2103 Interfacing

Figure 29 shows a serial interface between the DAC104S085 and the ADSP-2101 or ADSP2103. The DSP must

be set to operate in the SPORT Transmit Alternate Framing Mode. It is programmed through the SPORT control

Transmission is started by writing a word to the Tx register after the SPORT mode has been enabled.

Figure 29. ADSP-2101 and ADSP2103 Interface

8.5.3.2 80C51 and 80L51 Interface

Figure 30 shows a serial interface between the DAC104S085 and the 80C51/80L51 microcontroller. The SYNC

signal comes from a bit-programmable pin on the microcontroller. The example shown in Figure 30 uses port line

P3.3. This line is taken low when data is transmitted to the DAC104S085. Because the 80C51 and 80L51

transmits 8-bit bytes, only eight falling clock edges occur in the transmit cycle. To load data into the DAC, the

P3.3 line must be left low after the first eight bits are transmitted. A second write cycle is initiated to transmit the

second byte of data, after which port line P3.3 is brought high. The 80C51 and 80L51 transmit routine must

recognize that the 80C51 and 80L51 transmits data with the LSB first while the DAC104S085 requires data with

the MSB first.

Figure 30. 80C51 and 80L51 Interface

8.5.3.3 68HC11 Interface

Figure 31 shows a serial interface between the DAC104S085 and the 68HC11 microcontroller. The SYNC line of

the DAC104S085 is driven from a port line (PC7 in Figure 31), similar to the 80C51/80L51.

The 68HC11 must be configured with its CPOL bit as a zero and its CPHA bit as a one. This configuration

causes data on the MOSI output to be valid on the falling edge of SCLK. PC7 is taken low to transmit data to the

DAC. The 68HC11 transmits data in 8-bit bytes with eight falling clock edges. Data is transmitted with the MSB

first. PC7 must remain low after the first eight bits are transferred. A second write cycle is initiated to transmit the

second byte of data to the DAC, after which PC7 must be raised to end the write sequence.

Figure 31. 68HC11 Interface

8.5.3.4 Microwire Interface

Figure 32 shows an interface between a Microwire compatible device and the DAC104S085. Data is clocked out

on the rising edges of the SK signal. As a result, the SK of the Microwire device needs to be inverted before

driving the SCLK of the DAC104S085.

MICROWIRE

DEVICE DAC104S085

SCLK

DIN

SYNC

DAC104S085

DAC104S085-Q1

SNAS362G –MAY 2006–REVISED APRIL 2016

www.ti.com

Product Folder Links: DAC104S085 DAC104S085-Q1

Programming (continued)

Figure 32. Microwire Interface

LM4132-4.1

DAC104S085

DIN

SCLK

SYNC

VOUT = 0V to 4.092V

0.1 PFC2

2.2 PF

Input

Voltage

VA VREFIN

0.1 PF

DAC104S085

DAC104S085-Q1

www.ti.com

SNAS362G –MAY 2006–REVISED APRIL 2016

Product Folder Links: DAC104S085 DAC104S085-Q1

9 Application and Implementation

NOTE

Information in the following applications sections is not part of the TI component

specification, and TI does not warrant its accuracy or completeness. TI’s customers are

responsible for determining suitability of components for their purposes. Customers should

validate and test their design implementation to confirm system functionality.

9.1 Application Information

While the simplicity of the DAC104S085 implies ease of use, it is important to recognize that the path from the

reference input (VREFIN) to the VOUTs has essentially zero Power Supply Rejection Ratio (PSRR). Therefore, it is

necessary to provide a noise-free supply voltage to VREFIN. To use the full dynamic range of the DAC104S085,

the supply pin (VA) and VREFIN can be connected together and share the same supply voltage. Because the

DAC104S085 consumes very little power, a reference source may be used as the reference input and/or the

supply voltage. The advantages of using a reference source over a voltage regulator are accuracy and stability.

Some low noise regulators can also be used. Listed below are a few reference and power-supply options for the

DAC104S085.

9.1.1 LM4130

The LM4130, with its 0.05% accuracy over temperature, is a good choice as a reference source for the

DAC104S085. The 4.096-V version is useful if a 0 to 4.095-V output range is desirable or acceptable. Bypassing

the LM4130 VIN pin with a 0.1-µF capacitor and the VOUT pin with a 2.2-µF capacitor improves stability and

reduces output noise. The LM4130 comes in a space-saving, 5-pin SOT-23.

Figure 33. LM4130 as a Power Supply

9.1.2 LP3985

The LP3985 is a low-noise, ultra-low dropout voltage regulator with a 3% accuracy over temperature. It is a good

choice for applications that do not require a precision reference for the DAC104S085. It comes in 3-V, 3.3-V, and

5-V versions, among others, and sports a low 30-µV noise specification at low frequencies. Because low-

frequency noise is relatively difficult to filter, this specification could be important for some applications. The

LP3985 device comes in a space-saving, 5-pin SOT-23 and 5-bump DSBGA packages.

LP2980

1 PF

Input

Voltage

ON /OFF

VIN VOUT

VOUT = 0V to 5V

DAC104S085

DIN

SCLK

SYNC

VA VREFIN

0.1 PF

LP3985

1 PF0.1 PF

Input

Voltage

0.01 PF

VOUT = 0V to 5V

DAC104S085

DIN

SCLK

SYNC

VA VREFIN

0.1 PF

DAC104S085

DAC104S085-Q1

SNAS362G –MAY 2006–REVISED APRIL 2016

www.ti.com

Product Folder Links: DAC104S085 DAC104S085-Q1

Application Information (continued)

Figure 34. Using the LP3985 Regulator

An input capacitance of 1-µF without any ESR requirement is required at the LP3985 input, while a 1-µF ceramic

capacitor with an ESR requirement of 5 mΩto 500 mΩis required at the output. Careful interpretation and

understanding of the capacitor specification is required to ensure correct device operation.

9.1.3 LP2980

The LP2980 is an ultra-low dropout regulator with a 0.5% or 1% accuracy over temperature, depending upon

grade. It is available in 3-V, 3.3-V, and 5-V versions, among others.

Figure 35. Using the LP2980 Regulator

Like any low dropout regulator, the LP2980 requires an output capacitor for loop stability. This output capacitor

must be at least 1 µF over temperature, but values of 2.2 µF or more provides even better performance. The

ESR of this capacitor should be within the range specified in the LP2980 data sheet (SNOS733). Surface-mount

solid tantalum capacitors offer a good combination of small size and ESR. Ceramic capacitors are attractive due

to their small size, but, generally have ESR values that are too low for use with the LP2980. Aluminum

electrolytic capacitors are typically not a good choice due to their large size and have ESR values that may be

too high at low temperatures.

LM4050-4.1

LM4050-5.0 VOUT = 0V to 5V

0.47 PF

Input

Voltage

RVZ

DAC104S085

DIN

SCLK

SYNC

VA VREFIN

0.1 PF

IDAC

DAC104S085

DAC104S085-Q1

www.ti.com

SNAS362G –MAY 2006–REVISED APRIL 2016

Product Folder Links: DAC104S085 DAC104S085-Q1

9.2 Typical Application

Figure 36. The LM4050 as a Power Supply

9.2.1 Design Requirements

While the simplicity of the DAC104S085 implies ease of use, it is important to recognize that the path from the

reference input (VREFIN) to the VOUTs has essentially zero Power Supply Rejection Ratio (PSRR). Therefore, it is

necessary to provide a noise-free supply voltage to VREFIN. To use the full dynamic range of the DAC104S085,

the supply pin (VA) and VREFIN can be connected together and share the same supply voltage. Figure 36 uses an

LM4050 as a voltage reference source for the DAC104S085.

9.2.2 Detailed Design Procedure

Available with accuracy of 0.44%, the LM4050 shunt reference is also a good choice as a reference for the

DAC104S085. It is available in 4.096-V and 5-V versions and comes in a space-saving, 3-pin SOT-23.

The minimum resistor value in the circuit of Figure 36 must be chosen so that the maximum current through the

LM4050 does not exceed its 15-mA rating. The conditions for maximum current include the input voltage at its

maximum, the LM4050 voltage at its minimum, and the DAC104S085 drawing zero current. The maximum

resistor value must allow the LM4050 to draw more than its minimum current for regulation plus the maximum

DAC104S085 current in full operation. The conditions for minimum current include the input voltage at its

minimum, the LM4050 voltage at its maximum, the resistor value at its maximum due to tolerance, and the

DAC104S085 draws its maximum current. Equation 4 and Equation 5 summerize these conditions.

R(min) = ( VIN(max) −VZ(min) ) /IZ(max) (4)

and R(max) = ( VIN(min) −VZ(max) ) / ( (IDAC(max) + IZ(min) )

where

• VZ(min) and VZ(max) are the nominal LM4050 output voltages ± the LM4050 output tolerance over

temperature

• IZ(max) is the maximum allowable current through the LM4050

• IZ(min) is the minimum current required by the LM4050 for proper regulation

• IDAC(max) is the maximum DAC104S085 supply current. (5)

DAC104S085

DAC104S085-Q1

SNAS362G –MAY 2006–REVISED APRIL 2016

www.ti.com

Product Folder Links: DAC104S085 DAC104S085-Q1

Typical Application (continued)

9.2.3 Application Curves

Figure 37. 5-V Glitch Response Figure 38. Power-On Reset

10 Power Supply Recommendations

The DAC104S085 power supply should be bypassed with a 10-µF and a 0.1-µF capacitor as close as possible to

the device with the 0.1 µF right at the device supply pin. The 10-µF capacitor should be a tantalum type and the

0.1-µF capacitor must be a low ESL, low ESR type. The power supply for the DAC104S085 must only be used

for analog circuits.

2 GND

1 NetC1_1

NetC1_1

GND GND

GND

1 NetC1_1

NetC1_1

1 NetC1_1

GND

DAC104S085

DAC104S085-Q1

www.ti.com

SNAS362G –MAY 2006–REVISED APRIL 2016

Product Folder Links: DAC104S085 DAC104S085-Q1

11 Layout

11.1 Layout Guidelines

For best accuracy and minimum noise, the printed-circuit board containing the DAC104S085 must have separate

analog and digital areas. The areas are defined by the locations of the analog and digital power planes. Both of

these planes should be located in the same board layer. There must be a single ground plane. A single ground

plane is preferred if digital return current does not flow through the analog ground area. Frequently a single

ground plane design uses a fencing technique to prevent the mixing of analog and digital ground current.

Separate ground planes must only be used when the fencing technique is inadequate. The separate ground

planes must be connected in one place, preferably near the DAC104S085. Special care is required to ensure

that digital signals with fast edge rates do not pass over split ground planes. They must always have a

continuous return path below their traces.

Avoid crossover of analog and digital signals and keep the clock and data lines on the component side of the

board. The clock and data lines must have controlled impedances.

11.2 Layout Example

Figure 39. DAC104S085 Layout Example

DAC104S085

DAC104S085-Q1

SNAS362G –MAY 2006–REVISED APRIL 2016

www.ti.com

Product Folder Links: DAC104S085 DAC104S085-Q1

12 Device and Documentation Support

12.1 Device Support

12.1.1 Device Nomenclature

12.1.1.1 Specification Definitions

DIFFERENTIAL NON-LINEARITY (DNL) is the measure of the maximum deviation from the ideal step size of 1

LSB, which is VREF / 1024 = VA/ 1024.

DAC-to-DAC CROSSTALK is the glitch impulse transferred to a DAC output in response to a full-scale change

in the output of another DAC.

DIGITAL CROSSTALKis the glitch impulse transferred to a DAC output at mid-scale in response to a full-scale

change in the input register of another DAC.

DIGITAL FEEDTHROUGH is a measure of the energy injected into the analog output of the DAC from the digital

inputs when the DAC outputs are not updated. It is measured with a full-scale code change on the

data bus.

FULL-SCALE ERRORis the difference between the actual output voltage with a full scale code (3FFh) loaded

into the DAC and the value of VAx 1023 / 1024.

GAIN ERROR is the deviation from the ideal slope of the transfer function. It can be calculated from Zero and

Full-Scale Errors as GE = FSE - ZE, where GE is Gain error, FSE is Full-Scale Error and ZE is

Zero Error.

GLITCH IMPULSEis the energy injected into the analog output when the input code to the DAC register

changes. It is specified as the area of the glitch in nanovolt-seconds.

INTEGRAL NON-LINEARITY (INL) is a measure of the deviation of each individual code from a straight line

through the input to output transfer function. The deviation of any given code from this straight line

is measured from the center of that code value. The end point method is used. INL for this product

is specified over a limited range.

LEAST SIGNIFICANT BIT (LSB)is the bit that has the smallest value or weight of all bits in a word. This value is

LSB = VREF / 2n

where

• where VREF is the supply voltage for this product, and "n" is the DAC resolution in bits, which is 10 for

the DAC104S085. (6)

MAXIMUM LOAD CAPACITANCE is the maximum capacitance that can be driven by the DAC with output

stability maintained.

MONOTONICITY is the condition of being monotonic, where the DAC has an output that never decreases when

the input code increases.

MOST SIGNIFICANT BIT (MSB) is the bit that has the largest value or weight of all bits in a word. Its value is

1/2 of VA.

MULTIPLYING BANDWIDTHis the frequency at which the output amplitude falls 3dB below the input sine wave

on VREFIN with a full-scale code loaded into the DAC.

POWER EFFICIENCY is the ratio of the output current to the total supply current. The output current comes from

the power supply. The difference between the supply and output currents is the power consumed

by the device without a load.

SETTLING TIME is the time for the output to settle to within 1/2 LSB of the final value after the input code is

updated.

TOTAL HARMONIC DISTORTION (THD)is the measure of the harmonics present at the output of the DACs

with an ideal sine wave applied to VREFIN. THD is measured in dB.

WAKE-UP TIMEis the time for the output to exit power-down mode. This is the time from the falling edge of the

16th SCLK pulse to when the output voltage deviates from the power-down voltage of 0V.

DAC104S085

DAC104S085-Q1

www.ti.com

SNAS362G –MAY 2006–REVISED APRIL 2016

Product Folder Links: DAC104S085 DAC104S085-Q1

Device Support (continued)

ZERO CODE ERROR is the output error, or voltage, present at the DAC output after a code of 000h has been

entered.

12.2 Related Links

The table below lists quick access links. Categories include technical documents, support and community

resources, tools and software, and quick access to sample or buy.

Table 3. Related Links

PARTS PRODUCT FOLDER SAMPLE & BUY TECHNICAL

DOCUMENTS TOOLS &

SOFTWARE SUPPORT &

COMMUNITY

DAC104S085 Click here Click here Click here Click here Click here

DAC104S085-Q1 Click here Click here Click here Click here Click here

12.3 Community Resources

The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective

contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of

Use.

TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration

among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help

solve problems with fellow engineers.

Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and

contact information for technical support.

12.4 Trademarks

E2E is a trademark of Texas Instruments.

All other trademarks are the property of their respective owners.

12.5 Electrostatic Discharge Caution

This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with

appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.

ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more

susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.

12.6 Glossary

SLYZ022 —TI Glossary.

This glossary lists and explains terms, acronyms, and definitions.

13 Mechanical, Packaging, and Orderable Information

The following pages include mechanical, packaging, and orderable information. This information is the most

current data available for the designated devices. This data is subject to change without notice and revision of

this document. For browser-based versions of this data sheet, refer to the left-hand navigation.

PACKAGE OPTION ADDENDUM

www.ti.com 21-Jan-2016

Addendum-Page 1

PACKAGING INFORMATION

Orderable Device Status

(1)

Package Type Package

Drawing Pins Package

Qty Eco Plan

(2)

Lead/Ball Finish

(6)

MSL Peak Temp

(3)

Op Temp (°C) Device Marking

(4/5)

Samples

DAC104S085CIMM/NOPB ACTIVE VSSOP DGS 10 1000 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 105 X68C

DAC104S085CIMMX/NOPB ACTIVE VSSOP DGS 10 3500 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 105 X68C

DAC104S085CISD/NOPB ACTIVE WSON DSC 10 1000 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 105 X69C

DAC104S085CISDX/NOPB ACTIVE WSON DSC 10 4500 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 105 X69C

DAC104S085QIMM/NOPB ACTIVE VSSOP DGS 10 1000 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 X68Q

DAC104S085QIMMX/NOPB ACTIVE VSSOP DGS 10 3500 Green (RoHS

& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 X68Q

(1) The marketing status values are defined as follows:

ACTIVE: Product device recommended for new designs.

LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.

NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.

PREVIEW: Device has been announced but is not in production. Samples may or may not be available.

OBSOLETE: TI has discontinued the production of the device.

(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability

information and additional product content details.

TBD: The Pb-Free/Green conversion plan has not been defined.

Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that

lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.

Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between

the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.

Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight

in homogeneous material)

(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.

(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.

(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation

of the previous line and the two combined represent the entire Device Marking for that device.

PACKAGE OPTION ADDENDUM

www.ti.com 21-Jan-2016

Addendum-Page 2

(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish

value exceeds the maximum column width.

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information

provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and

continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.

TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.

OTHER QUALIFIED VERSIONS OF DAC104S085, DAC104S085-Q1 :

•Catalog: DAC104S085

•Automotive: DAC104S085-Q1

NOTE: Qualified Version Definitions:

•Catalog - TI's standard catalog product

•Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects

TAPE AND REEL INFORMATION

*All dimensions are nominal

Device Package

Type Package

Drawing Pins SPQ Reel

Diameter

(mm)

Reel

Width

W1 (mm)

(mm) B0

(mm) K0

(mm) P1

(mm) W

(mm) Pin1

Quadrant

DAC104S085CIMM/NOPB VSSOP DGS 10 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1

DAC104S085CIMMX/NOP

BVSSOP DGS 10 3500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1

DAC104S085CISD/NOPB WSON DSC 10 1000 178.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1

DAC104S085CISDX/NOP

BWSON DSC 10 4500 330.0 12.4 3.3 3.3 1.0 8.0 12.0 Q1

DAC104S085QIMM/NOP

BVSSOP DGS 10 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1

DAC104S085QIMMX/NO

PB VSSOP DGS 10 3500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1

PACKAGE MATERIALS INFORMATION

www.ti.com 21-Jan-2016

Pack Materials-Page 1

*All dimensions are nominal

Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)

DAC104S085CIMM/NOPB VSSOP DGS 10 1000 210.0 185.0 35.0

DAC104S085CIMMX/NOP

BVSSOP DGS 10 3500 367.0 367.0 35.0

DAC104S085CISD/NOPB WSON DSC 10 1000 210.0 185.0 35.0

DAC104S085CISDX/NOP

BWSON DSC 10 4500 367.0 367.0 35.0

DAC104S085QIMM/NOPB VSSOP DGS 10 1000 210.0 185.0 35.0

DAC104S085QIMMX/NOP

BVSSOP DGS 10 3500 367.0 367.0 35.0

PACKAGE MATERIALS INFORMATION

www.ti.com 21-Jan-2016

Pack Materials-Page 2

www.ti.com

PACKAGE OUTLINE

TYP

5.05

4.75

1.1 MAX

8X 0.5

10X 0.27

0.17

0.15

0.05

TYP

0.23

0.13

0 - 8

0.25

GAGE PLANE

0.7

0.4

NOTE 3

3.1

2.9

NOTE 4

3.1

2.9

4221984/A 05/2015

VSSOP - 1.1 mm max heightDGS0010A

SMALL OUTLINE PACKAGE

NOTES:

1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing

per ASME Y14.5M.

2. This drawing is subject to change without notice.

3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not

exceed 0.15 mm per side.

4. This dimension does not include interlead flash. Interlead flash shall not exceed 0.25 mm per side.

5. Reference JEDEC registration MO-187, variation BA.

110

0.1 C A B

PIN 1 ID

AREA

SEATING PLANE

0.1 C

SEE DETAIL A

DETAIL A

TYPICAL

SCALE 3.200

www.ti.com

EXAMPLE BOARD LAYOUT

(4.4)

0.05 MAX

ALL AROUND 0.05 MIN

ALL AROUND

10X (1.45)

10X (0.3)

8X (0.5)

(R )

TYP

0.05

4221984/A 05/2015

VSSOP - 1.1 mm max heightDGS0010A

SMALL OUTLINE PACKAGE

SYMM

LAND PATTERN EXAMPLE

SCALE:10X

NOTES: (continued)

6. Publication IPC-7351 may have alternate designs.

7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.

METAL

SOLDER MASK

OPENING

NON SOLDER MASK

DEFINED

SOLDER MASK DETAILS

NOT TO SCALE

SOLDER MASK

OPENING

METAL UNDER

SOLDER MASK

DEFINED

www.ti.com

EXAMPLE STENCIL DESIGN

(4.4)

8X (0.5)

10X (0.3)

10X (1.45)

(R ) TYP0.05

4221984/A 05/2015

VSSOP - 1.1 mm max heightDGS0010A

SMALL OUTLINE PACKAGE

NOTES: (continued)

8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate

design recommendations.

9. Board assembly site may have different recommendations for stencil design.

SYMM

SOLDER PASTE EXAMPLE

BASED ON 0.125 mm THICK STENCIL

SCALE:10X

MECHANICAL DATA

DSC0010A

www.ti.com

SDA10A (Rev A)

IMPORTANT NOTICE AND DISCLAIMER

TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE

DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”

AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY

IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD

PARTY INTELLECTUAL PROPERTY RIGHTS.

These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate

TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable

standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you

permission to use these resources only for development of an application that uses the TI products described in the resource. Other

reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third

party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims,

damages, costs, losses, and liabilities arising out of your use of these resources.

TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on

ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable

warranties or warranty disclaimers for TI products.

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265