Discontinued Mar. 30, 2009; Use E3Z-L Laser E3L E3L Laser Photoelectric Sensor E3L Prewired DC Sensor Provides LongDistance Sensing of Objects as Small as 0.1 mm Detect small objects over longer sensing distances with highly accurate positioning Attachable apertures allow detection down to 0.1 mm diameter Alarm output signals deteriorating detection conditions due to improper alignment or dust contamination Class I (FDA/IEC) laser product E3L-50, requires no additional protective equipment Visible spot through-beam version aids in critical alignment applications Ordering Information SENSORS Method of detection Through-beam Sensing distance 10 m (32.8 ft) 2 m (6.56 ft) 20 to 50 cm (7.9 to 19.7 in) Light source Visible red Infrared Infrared Laser class Class II Class I Class I NPN output E3L-2RC4 E3L-2E4-50 E3L-DS50E4-50 PNP output -- E3L-2B4-50 -- Part number Diffuse reflective REPLACEMENT PARTS Description Mounting bracket Part number For through-beam type; supplied with E3L-24- 50, E3L-2RC4 E39-L6 For diffuse reflective type; supplied with E3L-DS50E4-50 E39-L5 Sensitivity adjuster knob Apertures for through-beam types E39-G1 Aperture with 0.85 mm dia. opening E39-S56 Aperture with 0.10 mm dia. opening E39-S55 2 Discontinued Mar. 30, 2009; Use E3Z-L Laser E3L E3L Specifications E3L-2 4-50 Part number E3L-2RC4 (See Note.) Method of detection Through-beam type Supply voltage 12 to 24 VDC, 10% max. ripple peak-to-peak E3L-DS50E4-50 Diffuse reflective Current consumption 50 mA max. Sensing distance 10 m (32.8 ft) with no aperture; 9 m (29.52 ft) with 3 mm aperture; 6 m (19.68 ft) with 2 mm aperture; 3 m (9.84 ft) with 1 mm aperture; 2 m (6.56 ft) with 0.85 mm aperture; 1 m (3.28 ft) with 0.5 mm aperture; 30 cm (11.81 in) with 0.1 mm aperture 2 m (6.56 ft) with 0.85 mm dia. aperture; 20 cm (7.9 in) with 0.1 mm dia. aperture 40 mA max. Light source Visible red, pulse modulated laser diode (=670 nm) 480 W max., Class II FDA/IEC Infrared, pulse modulated laser diode (=780 nm) 25 W max., Class I FDA/IEC Detectable object type 4 mm (0.16 in) dia. object minimum without aperture; With aperture - object minimum is same as aperture size 0.5 mm (0.02 in) dia. object minimum with 0.85 mm dia. aperture 0.1 mm (0.003 in) dia. object minimum with 0.10 mm dia. aperture Diameter of projected spot With 4 mm dia. emitter, no aperture, at a distance of 2 m (6.56 ft), the incident light is 20 mm (0.79 in) in diameter Directional angle Emitter: 2 max., Receiver: 20 max. Operation mode Light-ON/Dark-ON, wire selectable Light-ON: + red, - black; Dark-ON: - red, + black 20 to 50 cm (7.9 to 19.7 in) with 2 x 2 mm (0.09 x 0.09 in) white mat paper Opaque, translucent objects 2 x 2 mm With 4 mm dia. emitter, at a distance of 50 cm (19.7 in) from the emitter, the incident light is 2 mm (0.08 in) in dia. Sensitivity adjustment Adjustable Mutual interference protection Standard level Control output Type NPN type, open collector NPN type, constant current source (E3L-E4-50) PNP type, open collector (E3L-2B4-50) Max. load NPN type: 100 mA max. NPN type: Load (relay, sink) logic: 80 mA max. Voltage (source) logic: 1.5 to 3 mA PNP type: Load (relay, source) logic: 80 mA max. Response time 1 ms max. (both ON and OFF) Type NPN (E3L-E4-50); PNP (E3L-2B4-50) Alarm output Circuit protection DC solidstate DC solidstate Max. load 50 mA, 24 VDC Residual voltage 1V Response time Output turns ON after 100 ms delay when light receiving signal level is within unstabe zone. Output shortcircuit Provided DC power supply reverse polarity Provided Indicators Materials 3 ms max. (both ON and OFF) Light Incident (red LED), Stable Operation (green LED) Lens Plastic, PMMA Case Diecast zinc (This table continues on the next page) Note: In consideration of vibration and other environmental and mounting conditions, the sensing distance values for the E3L-2RC4 are very conservative. If these conditions can be minimized, longer sensing distances are possible. Please see excess gain and operating range curves for more accurate sensing ranges. 3 Discontinued Mar. 30, 2009; Use E3Z-L Laser E3L E3L Specifications Table - continued from previous page E3L-2 4-50 Part number E3L-2RC4 Mounting Two side mount M4 threaded holes or mounting bracket E39-L6 (supplied) Two side mount M4 threaded holes or mounting bracket E39-L5 (supplied) 2 m (6.56 ft); 3 conductor cable for emitter, 3 conductor cable for receiver 2 m (6.56 ft) 4 conductor cable Connections Prewired Weight Enclosure Ambient 2 m (6.56 ft); 3 conductor cable for emitter, 4 conductor cable for receiver Emitter: 160 g (5.6 oz) Receiver: 175 g (6.2 oz) UL -- NEMA NEMA 4 250 g (8.8 oz) IEC 144 IP67 Operating -10C to 50C (14F to 122F) with no icing Storage -30C to 70C (-22F to 158F) OUTPUT CIRCUIT DIAGRAMS Sensor Through-beam Diffuse reflective NPN output type * * Alarm (orange) wire not present for E3L-2RC4 The indicator can be wired for Light Incident by connecting the black wires together as shown in the dotted line. For Power indication, connect the emitter's black wire to the receiver's blue wire. PNP output type The indicator can be wired for Light Incident by connecting the black wires together as shown in the dotted line. For Power indication, connect the emitter's black wire to the receiver's brown wire. TIMING CHARTS (between brown and black) (between blue and black) (between blue and black) (between brown and black) 4 E3L-DS50E4-50 Discontinued Mar. 30, 2009; Use E3Z-L Laser E3L E3L EXCESS GAIN 4-50 Through-beam Type E3L-2 Through-beam Type E3L-2RC4 Diffuse Reflective Type E3L-DS50E4-50 Sensing distance (cm) Slit 0.85 mm dia. Slit 0.1 mm dia. Excess gain ratio Excess gain ratio Excess gain ratio Slit 0.5, 1, 2, 3 mm dia. Sensing distance (m) Sensing distance (cm) 4-50 Through-beam Type E3L-2 without aperture 4-50 Through-beam Type E3L-2 with 0.85 mm diameter aperture 4-50 Through-beam Type E3L-2 with 0.1 mm diameter aperture Parallel offset distance Y (mm) Parallel offset distance Y (mm) Parallel offset distance Y (mm) OPERATING RANGE Sensing distance X (cm) Diffuse Reflective Type E3L-DS50E4-50 Through-beam Type E3L-2RC4 without aperture Through-beam Type E3L-2RC4 with 1.0 mm diameter aperture Parallel offset distance Y (mm) Parallel offset distance Y (mm) Sensing distance X (cm) Parallel offset distance Y (mm) Sensing distance X (cm) Sensing distance X (cm) with 2 x 2 mm white mat paper Sensing distance X (m) 5 Sensing distance X (m) Discontinued Mar. 30, 2009; Use E3Z-L Laser E3L Through-beam Type E3L-2RC4 with 0.85 mm diameter aperture Through-beam Type E3L-2RC4 with 0.5 mm diameter aperture Through-beam Type E3L-2RC4 with 0.1 mm diameter aperture Parallel offset distance Y (mm) Parallel offset distance Y (mm) Parallel offset distance Y (mm) E3L Sensing distance X (m) Sensing distance X (m) Sensing distance X (m) Dimensions Unit: mm (inch) 4- THROUGH-BEAM TYPE E3L-2 Sensitivity adjuster Indicators (for receiver only) Lens diameter Mounting holes Cable 2 m length 22.2 Mounting bracket E39-L6 supplied Two M4 hexagonal bolts 6 Note: Mounting bracket E39-L6 can be attached to surface "A". Discontinued Mar. 30, 2009; Use E3Z-L Laser E3L E3L DIFFUSE REFLECTIVE TYPE E3L-DS50E4-50 Unit: mm (inch) Mounting holes Cable, 2 m length Note: Mounting bracket E39-L6 can be attached to surface "A". REPLACEMENT PART Sensitivity Adjuster Knob E39-G1 (included) Note: The adjustment knob cannot be removed once it has been installed on the unit. 7 Discontinued Mar. 30, 2009; Use E3Z-L Laser E3L E3L Operation LIGHT INCIDENT INDICATOR Stability indicator (green LED) The LIGHT incident indicator (red LED) illuminates when the light from the emitter is incident on the receiver and exceeds the operating level (trigger point) of the sensor. This indicator illuminates whenever the object is absent for through-beam type and when the object is present for diffuse reflective type. Light incident indicator (red LED) STABILITY INDICATOR The STABILITY indicator (green LED) illuminates when the control output is in a stable OFF or ON state. A "stable" state occurs when the receiver element of the sensor receives less than 80% (OFF state) or more than 120% (ON state) of incident light needed to operate the sensor. The control output STABILITY indicator goes off every time the amount of light incident on the receiver is within 20% of the amount of light needed to change the control output state. The unstable control output condition may occur when the sensor encounters the leading and trailing edges of the object to be detected. However, the alarm output described later will not operate if the unstable condition recovers within 100 ms. The condition can occur when a change in sensor position, atmosphere (dust contamination), temperature or ambient light causes the light incident on the receiving element to be near the operating level of the sensor. ALARM OUTPUT (-50 models) The alarm output operates when the control output is in an unstable OFF or ON state for more than 100 ms. An unstable state occurs when the amount of light incident upon the receiver is within 20% of the amount of light needed to change the control output state. The alarm output feature indicates gradual degradation of stability caused by changes in sensor position, atmosphere, temperature or ambient light that will eventually result in an unstable control output. A change that occurs in less than 100 ms will not cause the alarm output to operate. A 100 ms time delay is built into the alarm output circuit. This prevents false triggering of the alarm output as the leading and trailing edges of the object to be detected are sensed. When sensing objects moving at low speeds, a separate ON-delay timer should be used to prevent false triggering of the alarm output. 8 Discontinued Mar. 30, 2009; Use E3Z-L Laser E3L E3L Precautions STATIC ELECTRICITY When handling the device, special care should be taken to avoid static electricity, as any static discharge can damage the laser diode element of E3L photoelectric sensor. LASER REGULATIONS The E3L laser photoelectric sensor is intended for use as an element incorporated into a larger system. Aperture Label for E3L-2LRC4 AVOID EXPOSURE The E3L laser photoelectric sensor meets the standards required by the Food and Drug Administration (FDA) in the United States. OMRON has had also reported to the Center for Devices and Radiological Health (CDRH). The report includes the condition that the unit is to be used as a part of a larger system. LASER RADIATION IS EMITTED FROM THIS APERTURE Labels (FDA Regulations) For products sold in North America, attach the following FDA safety labels for the appropriate sensor body proir to use. Some or all of these labels may already be attached. Labels (European) For exports to European countries, attach the appropriate label shown below to the cable. Caution Label E3l-2RC4 E3L-2 4-50 & E3L-DS50E4-50 CLASS I LASER PRODUCT Certification and Identification Label E3L-2L 4-50 TYPE E3L-2LE4-50 (Tc=25*C, 25 W) T: 50 sec ts: 2.5 sec f: 20 kHz This product complies with 21 CFR 1040.10 and 1040.11 OMRON Corporation 10 TSUCHIDO-CHO, HANAZONO, UKYO-KU, KYOTO 615 JAPAN MANUFACTURED JAN, 1990 E3L-2RC4 LASER RADIATION DO NOT STARE INTO BEAM CLASS 2 LASER PRODUCT Weight: Maximum output: Pulse duration: E3L-DS50E4-50 TYPE E3L-DS50E4-50 (Tc=25*C, 25 W) T: 200 sec ts: 5 sec f: 5 kHz This product complies with 21 CFR 1040.10 and 1040.11 OMRON Corporation 10 TSUCHIDO-CHO, HANAZONO, UKYO-KU, KYOTO 615 JAPAN MANUFACTURED JAN, 1990 670 nm 2 mw (Peak) 5 sec MAINTENANCE The E3L laser photoelectric sensor contains no userserviceable parts. Refer all servicing to an authorized OMRON agent. E3L-2LRC4 These devices generate Class I or Class II laser radiation. Avoid looking at the beam for prolonged periods. TYPE E3L-2LRC4 (Tc=25*C, 40 W) T: 60 sec ts: 5 sec f: 16.7 kHz This product complies with 21 CFR 1040.10 and 1040.11 OMRON Corporation KARASUMA NANAJO, SHIMOGYO-KU, KYOTO 600 JAPAN MANUFACTURED , 1990 Caution Do not disassemble the unit. Users expose themselves to the risk of laser radiation if they disassemsble the device, or use it for any purpose other than those described in this data sheet or in the instruction sheet provided with the unit. 9 Note: For more information on laser safelt and requirements, please see Omron's Measurement Sensors Catalog. Discontinued Mar. 30, 2009; Use E3Z-L Laser E3L E3L OMRON ELECTRONICS LLC OMRON ON-LINE OMRON CANADA, INC. One East Commerce Drive Schaumburg, IL 60173 Global - http://www.omron.com USA - http://www.omron.com/oei Canada - http://www.omron.com/oci 885 Milner Avenue Scarborough, Ontario M1B 5V8 1-800-55-OMRON Cat. No. CEDSAX4 11/01 Specifications subject to change without notice. 10 416-286-6465 Printed in the U.S.A.