IDT54/74FCT541/A/C FAST CMOS OCTAL BUFFER/LINE DRIVER MILITARY AND COMMERCIAL TEMPERATURE RANGES FAST CMOS OCTAL BUFFER/LINE DRIVER IDT54/74FCT541/A/C FEATURES: DESCRIPTION: - - - - - - - - The IDT octal buffer/line drivers are built using an advanced dual metal CMOS technology. The FCT541 is designed to be employed as a memory and address driver, clock driver and bus-oriented transmitter/receiver which provides improved board density. The FCT541 is similar in function to the FCT244, except that the inputs and outputs are on opposite sides of the package. This pinout arrangement makes these devices especially useful as output ports for microprocessors and as backplane drivers, allowing ease of layout and greater board density. IDT54/74FCT541 equivalent to FASTTM speed and drive IDT54/74FCT541A 25% faster than FAST IDT54/74FCT541C up to 55% faster than FAST IOL = 64mA (commercial) and 48mA (military) CMOS power levels (1mW typ. static) Military product compliant to MIL-STD-883, Class B Meets or exceeds JEDEC Standard 18 specifications Available in the following packages: * Commercial: SOIC * Military: CERDIP, LCC, CERPACK FUNCTIONAL BLOCK DIAGRAM OE A D0 D1 D2 D3 D4 D5 D6 D7 1 19 2 18 3 17 4 16 5 15 6 14 7 13 8 12 9 11 MILITARY AND COMMERCIAL TEMPERATURE RANGES OE B O0 O1 O2 O3 O4 O5 O6 O7 JUNE 2000 1 c 1999 Integrated Device Technology, Inc. DSC-5429/- IDT54/74FCT541/A/C FAST CMOS OCTAL BUFFER/LINE DRIVER MILITARY AND COMMERCIAL TEMPERATURE RANGES D1 3 18 O0 4 17 O1 D3 5 16 D4 6 D20-1 SO20-2 E20-1 15 O2 7 14 O4 D5 O3 D6 8 13 O5 D7 9 12 O6 10 11 O7 GND 4 D3 5 D4 6 D5 7 D6 8 3 2 9 10 TA TBIAS TSTG 11 12 18 O0 17 O1 16 O2 15 O3 14 O4 13 LCC TOP VIEW ABSOLUTE MAXIMUM RATINGS(1) VTERM(3) 19 L20-2 CERDIP/ SOIC/ CERPACK TOP VIEW Symbol VTERM(2) 20 1 D7 D2 D2 OE B OE B O5 19 V CC 2 O6 D0 OE A V CC O7 20 D0 1 GND INDEX OE A D1 PIN CONFIGURATION PIN DESCRIPTION Rating Terminal Voltage with Respect to GND Terminal Voltage with Respect to GND Operating Temperature Commercial -0.5 to +7 Military -0.5 to +7 Unit V -0.5 to VCC -0.5 to VCC V 0 to +70 -55 to +125 C Temperature Under Bias Storage Temperature -55 to +125 -65 to +135 C -55 to +125 -65 to +150 C PT Power Dissipation 0.5 0.5 W IOUT DC Output Current 120 120 mA Pin Names OEA, OEB Description 3-State Output Enable Inputs (Active LOW) Dx Inputs Ox Outputs FUNCTION TABLE(1) 8-link NOTES: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. No terminal voltage may exceed VCC by +.5V unless otherwise noted. OEA Inputs OEB L L L L L L H H H H X Z Dx Output Ox NOTE: 1. H = High Voltage Level X = Don't Care L = Low Voltage Level Z = HIGH Impedance 2. Input and VCC terminals only. 3. Outputs and I/O terminals only. CAPACITANCE (TA = +25OC, f = 1.0MHz) Symbol CIN Parameter(1) Input Capacitance Conditions VIN = 0V Typ. 6 Max. 10 Unit pF COUT Output Capacitance VOUT = 0V 8 12 pF 8-link NOTE: 1. This parameter is measured at characterization but not tested. c 1998 Integrated Device Technology, Inc. 2 DSC-123456 IDT54/74FCT541/A/C FAST CMOS OCTAL BUFFER/LINE DRIVER MILITARY AND COMMERCIAL TEMPERATURE RANGES DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE Following Conditions Apply Unless Otherwise Specified: VLC = 0.2V; VHC = VCC - 0.2V Commercial: TA = 0C to +70C, VCC = 5.0V 5%; Military: TA = -55C to +125C, VCC = 5.0V 10% Symbol VIH Parameter Input HIGH Level Test Conditions(1) Guaranteed Logic HIGH Level VIL Input LOW Level Guaranteed Logic LOW Level II H Input HIGH Current VCC = Max. II L Input LOW Current IOZH Off State (High Impedance) VCC = Max. Output Current IOZL Min. 2 Typ.(2) -- Max. -- Unit V -- -- 0.8 V A VI = VCC -- -- 5 VI = 2.7V -- -- 5(4) VI = 0.5V -- -- -5(4) VI = GND -- -- -5 VO = VCC -- -- 10 VO = 2.7V -- -- 10(4) VO = 0.5V -- -- -10(4) VO = GND A -- -- -10 Clamp Diode Voltage VCC = Min., IN = -18mA -- -0.7 -1.2 V IOS Short Circuit Current VCC = Max.(3), VO = GND -60 -120 -- mA VOH Output HIGH Voltage V VIK VOL Output LOW Voltage VCC = 3V, VIN = VLC or VHC, IOH = -32 A VHC VCC -- VCC = Min. IOH = -300 A VHC VCC -- VIN = VIH or VIL IOH = -12mA MIL. 2.4 4.3 -- IOH = -15mA COM'L. 2.4 4.3 -- -- GND VLC VCC = 3V, VIN = VLC or VHC, IOL = 300 A VCC = Min. IOL = 300 A -- GND VLC(4) VIN = VIH or VIL IOL = 48mA MIL. -- 0.3 0.55 IOL = 64mA COM'L. -- 0.3 0.55 V 8-link NOTES: 1. For conditions shown as Max. or Min., use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at VCC = 5.0V, +25C ambient and maximum loading. 3. Not more than one output should be shorted at one time. Duration of the short circuit test should not exceed one second. 4. This parameter is guaranteed but not tested. 3 IDT54/74FCT541/A/C FAST CMOS OCTAL BUFFER/LINE DRIVER MILITARY AND COMMERCIAL TEMPERATURE RANGES POWER SUPPLY CHARACTERISTICS VLC = 0.2V; VHC = VCC - 0.2V Symbol ICC Parameter Quiescent Power Supply Current ICC ICCD Quiescent Power Supply Current TTL Inputs HIGH Dynamic Power Supply Current(4) IC Total Power Supply Current (6) Test Conditions(1) VCC = Max. VIN VHC; VIN VLC VCC = Max. VIN = 3.4V(3) VCC = Max. Outputs Open OEA = OEB = GND or OEA = GND, One Input Toggling 50% Duty Cycle VCC = Max. Outputs Open fi = 10MHz 50% Duty Cycle OEA = OEB = GND or OEA = GND, One Bit Toggling VCC = Max. Outputs Open fi = 2.5MHz 50% Duty Cycle OEA = OEB = GND or OEA = GND, Eight Bits Toggling Min. -- Typ.(2) 0.2 Max. 1.5 Unit mA -- 0.5 2 mA VIN VHC VIN VLC -- 0.15 0.25 mA/ MHz VIN VHC VIN VLC (FCT) -- 1.7 4 mA VIN = 3.4V VIN = GND -- 2 5 VIN VHC VIN VLC (FCT) -- 3.2 6.5(5) VIN = 3.4V VIN = GND -- 5.2 14.5(5) NOTES: 1. For conditions shown as Max. or Min., use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at VCC = 5.0V, +25C ambient. 3. Per TTL driven input (VIN = 3.4V); all other inputs at VCC or GND. 4. This parameter is not directly testable, but is derived for use in Total Power Supply Calculations. 5. Values for these conditions are examples of the ICC formula. These limits are guaranteed but not tested. 6. IC = IQUIESCENT + IINPUTS + IDYNAMIC IC = ICC + ICC DHNT + ICCD (fCP/2 + fiNi) ICC = Quiescent Current ICC = Power Supply Current for a TTL High Input (VIN = 3.4V) DH = Duty Cycle for TTL Inputs High NT = Number of TTL Inputs at DH ICCD = Dynamic Current Caused by an Input Transition Pair (HLH or LHL) fCP = Clock Frequency for Register Devices (Zero for Non-Register Devices) fi = Input Frequency Ni = Number of Inputs at fi All currents are in milliamps and all frequencies are in megahertz. SWITCHING CHARACTERISTICS OVER OPERATING RANGE(1,2) 54/74FCT541 Com'l. Symbol tPLH tPHL tPZH tPZL tPHZ tPLZ Parameter Propagation Delay DN to ON Output Enable Time Output Disable Time Condition 54/74FCT541A Mil. Com'l. 54/74FCT541C Mil. Com'l. Mil. Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Min. Max. Unit 1.5 8 1.5 9 1.5 4.8 1.5 5.1 1.5 4.1 1.5 4.6 ns 1.5 10 1.5 10.5 1.5 6.2 1.5 6.5 1.5 5.8 1.5 6.5 ns 1.5 9.5 1.5 10 1.5 5.6 1.5 5.9 1.5 5.2 1.5 5.7 ns NOTES: 1. See test circuit and wave forms. 2. Minimum limits are guaranteed but not tested on Propagation Delays. 4 IDT54/74FCT541/A/C FAST CMOS OCTAL BUFFER/LINE DRIVER MILITARY AND COMMERCIAL TEMPERATURE RANGES TEST CIRCUITS AND WAVEFORMS SWITCH POSITION TEST CIRCUITS FOR ALL OUTPUTS V CC Test 7.0V Switch Open Drain 500 Disable Low V OUT V IN Pulse Generator D.U.T. All Other Tests 50pF R Closed Enable Low T C Open 8-link 500 DEFINITIONS: CL = Load capacitance: includes jig and probe capacitance. RT = Termination resistance: should be equal to ZOUT of the Pulse Generator. L O ctal lin k PULSE WIDTH SET-UP, HOLD, AND RELEASE TIMES 3V 1.5V 0V 3V 1.5V 0V DATA INPUT tH t SU TIM ING INPUT ASYNCHRONOUS C ONTROL PRES ET CLEAR ETC. SYNCHRO NOUS CONTRO L PRES ET CLEAR CLOCK ENABLE ETC. t REM t SU LO W -HIGH-LOW PULSE 1.5V tW 3V 1.5V 0V HIGH-LOW -HIGH PULSE 1.5V 3V 1.5V 0V tH O ctal lin k O ctal lin k PROPAGATION DELAY ENABLE AND DISABLE TIMES ENAB LE SAM E PHASE INPUT TRANSITION t PLH t PH L OUTPUT t PLH OPPOSITE P HASE INPUT TRANSITION t PH L 3V 1.5V 0V DISA BLE 3V CO NTROL INPUT 1.5V t PZL V OH 1.5V V OL OUTPUT NO RM A LLY LO W 3V 1.5V 0V SW ITCH CLOSE D O ctal lin k SW ITCH OPEN 3.5V 3.5V 1.5V 0.3V t PZH OUTPUT NO RM A LLY HIGH 0V t PLZ V OL t PHZ 0.3V V OH 1.5V 0V 0V O ctal lin k NOTES: 1. Diagram shown for input Control Enable-LOW and input Control Disable-HIGH. 2. Pulse Generator for All Pulses: Rate 1.0MHz; Zo 50; tF 2.5ns; tR 2.5ns. 5 IDT54/74FCT541/A/C FAST CMOS OCTAL BUFFER/LINE DRIVER MILITARY AND COMMERCIAL TEMPERATURE RANGES ORDERING INFORMATION ID T XX Tem p. R ange FC T XX XX XX X Device Type Package Process Blank B Com mercial MIL-STD-883, C lass B SO Com mercial O ptions Small O utline IC (SO 20-2) D E L Military Options CER DIP (D 20-1) CER PAC K (E20-1) Leadless Chip Carrier (L20-2) 541 541A 541B Fast C MO S O ctal Buffer/Line D river 54 74 - 55C to +125C - 40C to +85C CORPORATE HEADQUARTERS 2975 Stender Way Santa Clara, CA 95054 for SALES: 800-345-7015 or 408-727-6116 fax: 408-492-8674 www.idt.com* *To search for sales office near you, please click the sales button found on our home page or dial the 800# above and press 2. The IDT logo is a registered trademark of Integrated Device Technology, Inc. 6