1
New Product
Single-phase Power Controller
G3PW
High-precision Control with Easy Setup
Precise heater burnout detection.
Set value and present value monitoring with indicators.
Phase control or optimum cycle control.
RS-485 communications to set manipulated variables and
monitor load current.
Total run time monitoring.
Output modes for phase control: proportional to phase angle,
proportional to voltage, proportional to square voltage, and
constant-current control.
Application with various loads: constant load resistance,
variable load resistance.
UL, and IEC/EN (TÜV) certified.
Model Number Structure
Model Number Legend
Ordering Information
List of Models
Accessories (Order Separately)
Number of phases Control terminal block Type Capacity Heater burn-
out detection
Communica-
tions Model number
Single-phase
Screwless clamp termi-
nal block
Standard
20 A
100 to
240 VAC
No No
G3PW-A220EU-C
45 A G3PW-A245EU-C
60 A G3PW-A260EU-C
Constant
current
20 A
Yes Yes
G3PW-A220EC-C-FLK
45 A G3PW-A245EC-C-FLK
60 A G3PW-A260EC-C-FLK
Terminal block with
small slotted screws
Standard
20 A
No No
G3PW-A220EU-S
45 A G3PW-A245EU-S
60 A G3PW-A260EU-S
Constant
current
20 A
Yes Yes
G3PW-A220EC-S-FLK
45 A G3PW-A245EC-S-FLK
60 A G3PW-A260EC-S-FLK
Name Resistive value Display Model
External Variable
Resistor 2 kΩ202 G32X-V2K
For the most recent information on models that have been certified for
safety standards, refer to your OMRON website.
1324 8756
G3PW-A2@@E@-@-@@@
1. Basic model
G3PW: Power Controller
2. Degree of protection
A: Panel-mounting/Closed wallmounting
3. Voltage class
2: 200 VAC
4. Maximum rated current
20: 20 A
45: 45 A
60: 60 A
5. Power supply type
E: Single-phase power supply
6. Current control
U: Standard Model (no constant-current
control)
C: Constant-current Model
7. Control terminal block
C: Screwless clamp terminal block
S: Terminal block with small slotted screws
8.RS-485 communications
Blank: Communications not supported.
FLK: Communications supported.
G3PW
2
Ratings/Specifications
Model Standard Models Constant-current Models
Item G3PW-A2@@EU-@G3PW-A2@@EC-@-FLK
Control method Analog input: Phase control or optimum cycle control
Voltage ON/OFF input: ON/OFF control
Maximum load capacity Phase control: Linear (resistive) load, transformer primary-side control (flux density: 1.25 T max.)
Optimum cycle control: Linear (resistive) load (Transformer primaryside control is not supported.)
Output
mode
Analog in-
put Phase control Proportional to phase angle, proportional to square
voltage, proportional to voltage
Proportional to phase angle, proportional to square
voltage, proportional to voltage, constant-current
control
Optimum cycle control Optimum cycle control (Output is switched to 100% or 0% each half cycle.)
Voltage ON/
OFF input ON/OFF control Proportional to voltage control
Phase Single
Rated voltage 100 to 240 VAC
Operating voltage range 15% to +10%
Power supply frequency 50/60 Hz
Power supply frequency fluctuation ±3 Hz
Power consumption 5 VA max. (Control power D-E)
Load current range
-A220E@1 to 20 A
-A245E@1 to 45 A
-A260E@1 to 60 A
Inrush current resis-
tance
-A220E@220 A (60 Hz, 1 cycle)
-A245E@440 A (60 Hz, 1 cycle)
-A260E@440 A (60 Hz, 1 cycle)
I2t
-A220E@400A2s (1 cycle)
-A245E@1,600A2s (1 cycle)
-A260E@1,600A2s (1 cycle)
Output voltage adjustable range 0% to 98%
Input signal for con-
trol
Analog input 4 to 20 mA DC (input impedance: 100 Ω) or 1 to 5 VDC (input impedance: 30.1 kΩ)
Voltage ON/OFF Input 5 VDC (input impedance: 30.1 kΩ)
External main setting Specified Variable Resistor: G32X-V2K (2 kΩ, 2 W)
External duty setting Specified Variable Resistor: G32X-V2K (2 kΩ, 2 W)
Output value setting
range
Main setting 0.0% to 100%
Base-up value 0.0% to 100% (Default: 0.0%)
Upper/lower limits Output upper limit: 0.0% to 100% (Default: 100%)
Output lower limit: 0.0% to 100% (Default: 0.0%)
Duty setting
Duty setting = Internal duty setting x External duty setting
Internal duty setting range (set using front-panel keys or communications): 0% to 100% (Default: 100%)
External duty setting range (set using external variable resistor): 0% to 100% (Default: 100%)
Soft-start up time and soft-start down time 0.0 to 99.9 s (Default: 0.5 s)
Either phase control or optimum cycle control can be used.
Constant current --- Current fluctuation: ±2% FS
Load current upper limit --- 0.0 to 66.0 A (Default: 0.0 = OFF)
Overcurrent detection time: 500 ms max.
Current detection
Current transformer (CT) --- Built-in
Current detection accuracy --- 10% FS of rated current
Minimum detected load cur-
rent --- 1 A
Heater burnout alarm
Detection method ---
According to heater resistance (with heater resistance
teaching and Heater Burnout Threshold parameter)
Note: The accuracy of heater burnout detection will
be lower for heaters for which the resistance
significantly changes depending on the
temperature.
Setting range for heater
burnout detection --- 1% to 100% (Default: 100%)
Burnout detection accuracy --- 10% FS at rated current
(Not applicable to loads with variable resistance.)
Burnout detection output
lower limit ---
Detects a burnout at or above the specified output
value.
0.0% to 100% (Default: 0.0%)
Number of alarms for heater
burnout detection --- 0 to 999 (Default: 150)
Multiple heater burnout
detections --- Burnout of 1 of 10 heater elements can be detected
(at the rated current).
Event inputs
Number of event inputs
2 event inputs
Event input 1: The function of the event input can be changed with a parameter setting in the initial setting
level. The event input can be used for one of the following functions.
Switching the main setting between automatic and manual operation.
Switching between phase control and optimum cycle control.
Event input 2: Alarm reset
Contact input conditions ON: 1 kΩ max., OFF: 100 kΩ min.
Non-contact input condi-
tions ON residual voltage: 1.0 V max., OFF leakage current: 0.1 mA max.
Current flow Approx. 1.1 mA (per input)
Output voltage 5 VDC
G3PW
3
Fuses (recommended models for external connection)
*Ask your OMRON representative for UL certified products.
Time-delay fuses specifications
Model Standard Models Constant-current Models
Item G3PW-A2@@EU-@G3PW-A2@@EC-@-FLK
Alarm outputs
Number of alarm outputs
2 alarm outputs
Alarm output 1: ALARM1 (caution)
Alarm output 2: ALARM2 (warning)
Open-collector outputs (Individual common)
Maximum operating voltage 30 VDC
Maximum load current 50 mA
Maximum residual voltage 1.5 V
Maximum leakage current 0.4 mA
Serial communications ---
One RS-485 port: CompoWay/F slave function (See
note.)
Note: Connection is possible to a Basic Unit in an EJ1
Modular Temperature Controller. Parameters can
be set and monitored from the CX-Thermo Sup-
port Software running on a computer that is con-
nected to the EJ1 End Unit.
Overcurrent detection --- Rated current × 120% min., within 250 cycles
SSR failure detection
An error is detected within 3 seconds after an SSR failure.
Phase angle range for SSR short-circuit failure detection: 0% to 72%
Phase angle range for SSR open failure detection: 28% to 100%
Output ON voltage drop 1.6 Vrms (at 100 % output on)
Power supply frequency error Not within 47 to 63 Hz
Leakage current 10 mA max. (100/110 VAC), 20 mA max. (200/220 VAC)
Insulation resistance 100 MΩ min. (at 500 VDC)
Dielectric strength 2,500 VAC at 50/60 Hz for 1 min between charged parts and noncharged parts
Vibration resistance 10 to 55 to 10 Hz, 100 m/s2
Shock resistance 300 m/s2
Ambient operating temperature 15°C to 55°C (with no icing or condensation)
Ambient operating humidity 5% to 95%
Storage temperature 25°C to 65°C (with no icing or condensation)
Weight
G3PW-A220E@-@-@@@: 1.0 kg max.
G3PW-A245E@-@-@@@: 1.9 kg max.
G3PW-A260E@-@-@@@: 1.9 kg max.
Applicable
Standards
Safety Standards
UL508
CSA C22.2 No.14
EN60947-4-3 (pollution degree 2, overvoltage category II)
EMC Directives
EMI EN60947-1
EN60947-4-3
EMS EN60947-1
EN60947-4-3
Recommended models
Type Super-rapid Fuse (Fuji Electric) Fuse Holder
(Fuji Electric)
Fast-acting fuses *
For 20 A CR6L-20/UL CMS-4
For 45 A CR6L-50/UL
For 60 A CR6L-75/UL CMS-5
Type Specification
Time-delay fuses 250 VAC, 2 A
G3PW
4
Nomenclature and Operations
Level Indicators
Monitoring Indicators
Communications Indicator
Operation Keys
Level indicators
LVL Key
UP Key
ENT/RST Key
Command input and
power supply terminal
block (with cover)
1. 1 to 5-V/0 or 5-V input
2. 4 to 20-mA input
3. Current/voltage input COM
4. 100 to 240 VAC
5. 100 to 240 VAC
Protective cover
(removable)
Communications
indicator
Monitoring indicators
7-segment display
Load terminal block
(under protective cover)
100 to 240 VAC
Reset/event indicator
DOWN Key
Control terminal block
Indicator Description
ADJ Lit when in the adjustment level.
SET Lit when in the initial setting level.
EV Lit when an external contact reset input or an event input is ON.
Indicator Description
%(IN) Lit when the input value is monitore d in the monitor level.
%(DUTY) Lit when the duty value is monitored in the monitor level.
%(OUT) Lit when the output va lue is monitored in the monitor level.
%(PHASE) Lit when the phase angle is monit ored in the monitor level.
A Lit when the current is monitored in the monitor level.
Indicator Description
COMM Lit when the serial communications are in progress.
Key symbol Name Description Enabling condition
LVL (level) Key
Level Changes
Monitor level Adjustment level
Monitor level Initial setting level
Software is reset when moving from the initial set-
ting level to monitor level.
Changing from monitor le vel to adjustment level o r
from monitor level to in itial setting level is possible
even when an error occurs.
ENT/RST (en-
ter/reset) Key
Set value display
Set value change and entry
Error reset
In the monitor level, t he ENT/RST Key functions as
a Reset Key only when an error occurs. (It does not
function as a Reset Key when there is no error.)
UP Key Set value change
Monitor item/set value numb er change ---
DOWN Key
G3PW
5
Engineering Data
Ambient Temperature
Note: 1. The ambient operating temperature range is 15 to 55°C, but take the following considerations into account. When the ambient
temperature exceeds 40°C, reduce the maximum load current as shown below.
2. At least 20 mm must be provided on the left and right sides of the G3PW-A260E@. If you must use side-by-side mounting, then reduce
the maximum load current when the ambient temperature is over 30°C.
3. Certification for safety standards was obtained with a mounting interval of 20 mm.
4. Leave sufficient space for ventilation.
5. Do not install the Power Controller above devices that generate significant amounts of heat, such as heaters, transformers, and high-
capacity resistors.
6. If the ambient temperature reaches 55°C or higher, install an air conditioner to lower the temperature.
Resistance to Inrush Current (For repetitive inrush current, keep the inrush current below the values shown by the dotted lines.)
Current and Temperature Characteristics
G3PW-A220E@/A245E@ G3PW-A260E@
Load current (%)
20
40
60
80
100
Ambient temperature (°C)
5510 20 30 40 50 600
20
40
60
80
100
5510 20 30 40 50 600
B
A
A: Installation with 20 mm
between Power Controllers
B: Close mounting
Load current (%)
Ambient temperature (°C)
G3PW-A220E@G3PW-A245E@/G3PW-A260E@
Inrush current (A. peak)
200
150
100
50
05,0001,000500200100503010
Power ON time (ms)
400
300
200
100
05,0001,000500200100503010
Inrush current (A. peak)
Power ON time (ms)
G3PW
6
Dimensions
Note: All units are in millimeters unless otherwise indicated.
170 146.4
50
137
120 40
100 min.
158±0.2
Two, M5 38±0.2
51 min.
20-A Models with Screwless Clamp Terminal Block
G3PW-A220EU-C
G3PW-A220EC-C-FLK
Mounting Hole Dimensions
188 171.5
70
155
138
104
71 min.
100 min.
176±0.2
100 min.
176±0.2
57.6±0.2
Two, M5
Two, M5
G3PW-A260EU-C
G3PW-A260EC-C-FLK
G3PW-A245EU-C
G3PW-A245EC-C-FLK
90 min.
57.6±0.2
45/60-A Models with Screwless Clamp Terminal Block
G3PW-A245EU-C
G3PW-A260EU-C
G3PW-A245EC-C-FLK
G3PW-A260EC-C-FLK
Mounting Hole Dimensions
G3PW
7
Accessories (Order Separately)
170 146.4
50
136.5
120 40
100 min.
158±0.2
Two, M5 38±0.2
51 min.
20-A Models with Terminal Block with Small Slotted Screws
G3PW-A220EU-S
G3PW-A220EC-S-FLK
Mounting Hole Dimensions
188 171.5
70
154.5
138
104
71 min.
100 min.
176±0.2
100 min.
176±0.2
57.6±0.2
Two, M5
Two, M5
G3PW-A260-EU-S
G3PW-A260-EC-S-FLK
G3PW-A245EU-S
G3PW-A245EC-S-FLK
90 min.
57.6±0.2
45/60-A Models with Terminal Block with Small Slotted Screws
G3PW-A245EU-S
G3PW-A260EU-S
G3PW-A245EC-S-FLK
G3PW-A260EC-S-FLK
Mounting Hole Dimensions
2.8±0.2 dia.
1±0.1
M9P0.75
1.6±0.2
10
±1
20±1
17 max.
15 min.
2.5±1
31±1 dia. 12±0.2
R26 max.
30 max.
6 0
0.1dia. 34
26
13.4
1.6 6.5
14
17
Filled with white resin
External Variable Resistor
G32X-V2K
12
±0.2
3 dia.
9.5 dia.
Mounting Holes Nameplate
48
48
Knob
G3PW
8
Safety Precautions
Do not attempt to disassemble the Power Controller
while the power is being supplied. Doing so may
occasionally result in strong electric shock.
Do not touch any of the terminals while the power is
being supplied. Also, always attach the terminal block
cover after completing wiring. Touching live terminals
may occasionally result in serious injury due to
electric shock.
Fail-safe measures must be taken by the customer to
ensure safety in the event of incorrect, missing, or
abnormal signals caused by broken signal lines,
momentary power interruptions, or other causes.
Abnormal operation may result in serious accidents.
Do not use the Power Controller where subject to
flammable or explosive gas. Otherwise, explosion may
occur.
Use the wire sizes given in this document and use
twisted copper wires or solid copper wire.
Use crimp terminals with insulative sleeves. If the
crimp terminals do not come with insulative sleeves,
attach insulative sleeves. Use the size of crimp terminals
specified in this document.
Make sure that the phases match for load terminal T1
and power supply terminal 4 (N), and for load terminal
L1 and power supply terminal 5 (L). Insert suitable
fuses in the power supply line and load output line to
protect the circuits.
The Power Controller will not operate normally if the
wiring is not correct, and the load may be damaged.
Leave at least 100 mm of space above and below the
Power Controller when installing it to allow heat to
dissipate. Do not obstruct the area around the Power
Controller and especially the area around the heat
sink.
Install the Power Controller in the direction shown in
this Instruction Sheet. The Power Controller generates
a lot of heat and it uses natural heat convection for
cooling. Installing the Power Controller in the wrong
direction may cause in malfunctions or accidents.
Do not touch the terminal sections while a voltage is
being applied after the power supply terminal block
and load terminal block have been wired.
The power supply terminal block and load terminal
block are not isolated to enable an alarm function.
Electric shock may occur.
The Power Controller and the heat sink become very
hot. Do not touch anything but the setting keys while
power is being supplied or jus t after the power suppl y
is turned OFF. Doing so may cause burns.
Do not attempt to disassemble, modify, or repair the
Power Controller or touch any of the internal parts.
Minor electric shock, fire, or malfunction may
occasionally occur.
Do not allow chips or filings from installation work,
pieces of metal, or wire clippings to enter the Power
Controller. Doing so may occasionally result in minor
electric shock, fire, or malfunction.
Always connect the load to load terminal T1. Also,
always connect power supply terminal 4 (N) directly to
the power supply. Do not connect it through the load.
If the wiring is not correct, the fault detection function
of the Power Controller will indicate “E10” and stop the
output operation. Check the connection again.
When using the Power Controller to control the
primary side of a transformer, do not open the circuit
on the secondary side of the transformer while the
Power Controller is operating.
Do not touch the connecting cables while power is
being supplied. Static electricity from your body may
cause malfunctioning.
If a malfunction in the Power Controller prevents
control operations or if an alarm cannot be output, it
may occasionally cause damage to the connected
equipment and devices. To maintain safety in the event
of a malfunction in the Power Controller, always take
appropriate safety measures, such as installing a
separate monitoring system.
Set the parameters of the Power Controller so that they
are suitable for the system being controlled. If they are
not suitable, unexpected operation may occasionally
result in property damage or accidents.
Tighten the terminal screws to the torque specified in
this Instruction Sheet. If the screws are loose, it may
occasionally cause a fire.
WARNING CAUTION
G3PW
9
OMRON constantly strives to improve quality and reliability. The
G3PW, however, uses semiconductors, and semiconductors may
commonly malfunction or fail. In particular, it may not be possible to
ensure safety if the G3PW is used outside the rated ranges.
Therefore, always use the G3PW within the ratings. When using the
G3PW, always design the system to ensure safety and prevent
human accidents, fires, and social harm in the event of G3PW failure.
System design must include measures such as system redundancy,
measures to prevent fires from spreading, and designs to prevent
malfunction.
1. Do not apply a voltage or current in excess of the ratings to the
terminal sections of the G3PW. Doing so may result in failure of
the G3PW or fire damage.
2. Do not use the G3PW with loose terminals screws. Abnormal
terminal heat may result in fire damage.
3. Do not obstruct the airflow around the heat sink of the G3PW.
Abnormal heat may result in failure due to shorting of the output
terminals or fire damage.
4. Be sure to read the Precautions for Correct Use to correctly
perform wiring and tighten screws. Using the G3PW with
incorrect wiring or insufficient screw tightening may result in fire
damage due to abnormal heat when the power is supplied.
Installation Environment
Use the Power Controller within the rated ambient temperature and
humidity ranges.
If multiple Power Controllers are installed side-by-side or vertically,
the heat that is generated will cause the internal temperatures of
the Power Controllers to rise and will shorten their service life. In
these kinds of installations, take suitable measures, such as
installing fans for forced cooling.
The Power Controller is designed for indoor use only. Also, do not
use the Power Controller in the following environments.
Locations subject to water, oil, or chemicals
Locations subject to direct sunlight
Locations where dust or corrosive gases (in particular, sulfuric or
ammonia gas) are present
Locations subject to extreme temperature changes
Locations where icing or condensation may occur
Locations subject to excessive shocks or vibration
Locations subject to direct heat radiated from heating devices
Installation and Wiring
When installing the Power Controller, always securely tighten the
top mounting screws first. When removing the Power Controller,
always remove the bottom mounting screws first.
Take safety measures, such as wearing safety shoes, in case the
Power Controller falls.
Touch the Power Controller only after first touching a grounded
metal object to discharge any static electricity from your body.
Always ground the Power Controller to 100 Ω or less. There are no
ground terminals provided, so use the heat sink mounting screws
as ground terminals.
Check the terminal number and polarity for each input before
connecting it.
Use copper twisted wire in the sizes specified in this Instruction
Sheet.
Use insulated crimp terminals with insulation sleeves. If using
crimp terminals that are not insulated, cover them with insulation
sleeves. Also, use terminals of the sizes specified in this Instruction
Sheet.
Insert connectors all the way.
Do not connect anything to unused terminals.
Safety Measures and Checking
Install a switch or circuit breaker so that the operator can
immediately turn OFF the power, and provide a suitable display.
Apply the power supply voltage through the contacts of a switch,
relay, or similar device so it reaches the rated voltage within 2 s. If
the power supply voltage is increased gradually, the power supply
may not be reset or outputs may malfunction.
Use a power supply voltage, input voltage, input current, and load
within the specifications and rated ranges for the Power Controller.
Use a load that draws a current at the maximum output that is
within the rated current range of the Power Controller. If the current
drawn by the load is not within the rated current range, malfunction
or fire may occur.
Make sure that the protective cover is attached to the load terminal
block before using the Power Controller. Failure to do so may
damage internal components due to mechanical stress.
Preventing Inductive Noise
Allow as much space as possible between the Power Controller
and devices that generate powerful high frequencies (high-
frequency welders, high-frequency sewing machines, etc.) or
surge.
Keep the signal lines that connect to the Power Controller's
terminal block away from power cables carrying high voltages or
large currents. Also, do not wire power lines together with or
parallel to Power Controller wiring. Using shielded cables and
using separate conduits or ducts is recommended.
Attach a surge suppressor or noise filter to peripheral devices that
generate noise (in particular, motors, transformers, solenoids,
magnetic coils or other equipment that have an inductance
component).
When a noise filter is used at the power supply, first check the
voltage or current, and attach the noise filter as close as possible
to the Power Controller.
Cleaning
Do not use paint thinner or similar chemical to clean with. Use
commercially available standard grade alcohol.
Storage
Store the Power Controller within the rated ambient temperature.
Precautions for Safe Use
G3PW
10
Installation Direction
For cooling efficiency, install the Power Controller in the correct
direction. The G3PW generates a lot of heat, and it uses natural heat
convection for cooling. Installing the Power Controller in the wrong
direction may cause it to malfunction or to be damaged.
Wiring the Power Supply and Load Circuits
The G3PW will not operate correctly if the wiring is not correct. The
failure detection function of the G3PW will stop the output from
operating.
Connect the AC power supply to power supply terminals 4 (N) and 5
(L).
Connect the load to load terminal T1 and to the power supply, and
then connect the power supply to load terminal L1 through a fast-
acting fuse.
The AC power supply ground polarity and the G3PW terminal block
polarity are not related, but connect the 4 (N) and 5 (L) terminals on
the command input/power supply terminal block and the T1 and L1
terminals of the load terminal block to power supplies with the same
phases.
Wiring the Load Terminal Block
Recommended Wires
When connecting to the load terminals, use the specified wire size for
each model of Power Controller.
*Crimp terminals that conform to UL and CSA specifications must be
used.
Recommended Crimp Terminals
Either use insulated crimp terminals or cover the crimp terminals
with insulating sleeves.
Always use the following crimp terminals to wire the load terminals.
Do not connect more than two crimp terminals to one terminal
screw.
Recommended Fuses
*Ask your OMRON representative for UL certified products.
Time-delay fuses specifications
Command Input and Power Supply Terminal Wiring
Voltage Input (1 to 5 VDC)
When using a voltage input, connect the positive and negative signal
wires to terminals 1 and 3, respectively.
Current Input (4 to 20 mA DC)
When using current input, connect the positive and negative signal
wires to terminals 2 and 3, respectively.
Note: If you connect more than one G3PW Controller for current
input, do not connect the negative terminal of the event input/
reset input (L/N) and the current input terminal -3 as negative
commons on the G3PW Controllers. If you do, the second and
later G3PW Controllers may not operate.
Precautions for Correct Use
Natural
convection
To p
Bottom
Mounting surface
Specified distance
or longer
100 mm
min. Airflow
Other device
Other device
Other device
Other device
100 mm
min.
Command
input/power
supply
terminal
block
Load
terminal block
Load circuit (T1)
Load circuit (L1)
Fast-acting fuse
Power supply
100 to 240 VAC
(50/60 Hz)
Time-delay
fuse
Load
T1 L1
LN
12345
Model Recommended wire
size
Tightening
torque
Terminal
screws
G3PW-A220 AWG 18 to 10 1.8 N·m M4
G3PW-A245 AWG 6 *2.8 N·m M5
G3PW-A260
Recommended models
Type Super-rapid Fuse (Fuji Electric) Fuse Holder
(Fuji Electric)
Fast-acting fuses *
For 20 A CR6L-20/UL CMS-4
For 45 A CR6L-50/UL
For 60 A CR6L-75/UL CMS-5
Type Specification
Time-delay fuses 250 VAC, 2 A
A
Model A (mm)
G3PW-A220 9.5 max.
G3PW-A245/A260 12 max.
Temperature
controller or
other controller
1 to 5-V output
54
LN
123
4 to 20 mA output
Max. 6 units are possible to connect (In case, Input impedance of Temperature controller is 600 Ω max.)
Temperature
controller or
other controller
LNLNLN
54
123 54
123 54
123
G3PW
11
ON/OFF Voltage Input (0 or 5 VDC)
When using an ON/OFF voltage input, connect the positive and
negative signal wires to terminals 1 and 3, respectively and apply a
command voltage that is 0 or 5V.
The G3PW may be damaged if a command voltage that is higher than
5 V is applied. If it is necessary to apply more than 5 V, split the
voltage as shown below by inserting resistance in the line to terminal
1 and applying the voltage across terminals 1 and 3. The internal
impedance between terminals 1 and 3 is 30.1 kΩ.
Command Input and Power Supply Wire Sizes
Recommended Crimp Terminals
Always use the following crimp terminals (for M3.5) to wire to the
command input and power supply terminals.
Wiring the Control Terminal Block
Recommended Wire Sizes and Connection Method
G3PW-A2@@E@-S (Models with terminal blocks with small
slotted screws)
G3PW-A2@@E@-C (Models with screwless clamp terminal block)
Wire Sizes for Control Terminals (Models with Small Slotted
Screws or Screwless Clamp Terminals)
Use copper AWG 26 to 16 twisted-pair cable when connecting the
wires directly.
Strip the wire sheathing for the following lengths, according to the
connector type.
Small slotted screw terminals: 7 mm
Screwless clamp terminals: 9 mm
When using twisted wires, it is recommended that you attach a
ferrule with an insulating cover that conforms to DIN 46228-4 and
connect the ferrule to the terminal.
Use shielded twisted-pair wires for RS-485 communications wires.
A maximum of 500 m total of wiring can be used.
Failure Detection Wiring
Sufficiently consider the safety design of the system design so that
the load circuit is turned OFF using the alarm output when a failure is
detected in the G3PW.
Terminal Name s
Wiring Inputs for External Settings
Alarm Outputs
Wiring an External Noise Filter
Always insert a noise filter in the power supply lines to the G3PW.
Grounding
Always ground the Power Controller to 100 Ω or less. There are no
ground terminals provided, so use the heat sink mounting screws as
ground terminals.
Model Recommended wire
diameter Tightening
torque Terminal
screws
All models AWG 18 to 14 0.8 to 1.0 N·m M3.5
Model Recommended wire
diameter Tightening
torque Terminal
screws
All models AWG 26 to 16 0.22 N·m M2
PLC
or
other controller 0 or 5-V output
54 LN
123
Internal impedance: 30.1 kΩ
Output of 5 V
or higher Resistance
PLC or
other
controller
LN123 Output
voltage Resistance
0 or 5 V Not required
0 or 12 V
42 k
Ω
, 1/5 W min.
0 or 24 V
120 k
Ω
, 1/5 W min.
7.2 mm max.
7.2 mm max.
1. RS-485 (+)
2. RS-485 (−)
3. Main setting
4. Main setting COM
5. Duty setting
6. Duty setting COM
7. Alarm output 1 (+)
8. Alarm output 1 (−)
9. Alarm output 2 (+)
10. Alarm output 2 (−)
11. Event input (+)
12. Event input (−)
13. Reset input (+)
14. Reset input (−)
For standard models, 1 and 2
are not used.
Multi-drop
Max. of 31 nodes *
* A terminator must be connected at each end of the RS-485 transmission
path. The terminators must be at least 54 Ω combined.
Load
Automatic
Manual
Load
EJ1 Modular Temperature
Controller, CJ-series Serial
Communications Unit, etc.
2
3
13. Main setting
4. Main setting
COM
5. Duty setting
6. Duty setting
COM
2
3
1
Wiring to Adjust the Main
Setting
Use a G32X-V2K Variable
Resistor to adjust the main
setting.
Wiring to Adjust the Duty
Setting
Use a G32X-V2K Variable
Resistor to adjust the duty
setting.
1
2
3
4
5
6
7. Alarm output 1 (+)
8. Alarm output 1 (−)
9. Alarm output 2 (+)
10. Alarm output 2 (−)
11
12
13
14
Load
Load
Output status Open collector
Number of out-
puts 2
Maximum oper-
ating voltage 30 VDC
Maximum load
current 50 mA
Maximum resid-
ual voltage 1.5 V
Maximum leak-
age current 0.4 mA
Load circuit (T1)
Load circuit (L1)
Power supply
100 to 240 VAC
(50/60 Hz)
Time-delay
fuse
Fast-acting fuse
Load
Command
input/power
supply
terminal
block
Load
terminal block
T1 L1
LN
123
3
4
1
2
45
Noise Filter
RSMN-2030/2060
(TDK-Lambda
Corporation)
12
Advanced Digital Temperature Controller
E5CN-H (48 x 48 mm)
A New High-performance Controller: High Resolution, High Speed, and
High Input Accuracy.
Logic Operations and Preventive Maintenance Function.
High-resolution display with 5 digits/0.01°C display in a compact
Controller (48 x 48 mm).
High-speed sampling cycle of 60 ms.
High Accuracy
Thermocouple/Pt input: ±0.1% of PV
Analog input: ±0.1% FS
Universal inputs on all models (thermocouple, PT, or analog input)
to handle various sensors with one Controller.
A PV/SV-status display function can be set t o automatically alternate
between displaying the status of the Temperature Controller (auto/
manual, RUN/STOP, and alarms) and the PV or SV.
Flexible contact outputs with logic operations (AND, OR, and
delays) set from the Support Software (CX-Thermo Ver. 4.0)
Preve ntive maintenanc e fo r rela ys in the T em p er at ur e Con tr oller
using a Control Output ON/OFF Counter.
48 × 48 mm
E5CN-H
Advanced Digital Temperature Controller
E5AN-H/E5EN-H (96 x 96 mm and 48 x 96 mm)
A New High-performance Controller: High Resolution, High Speed, and
High Input Accuracy.
Logic Operations and Preventive Maintenance Function.
Plus Infrared Port on Front Panel.
High-resolution display with 5 digits/0.01°C display.
High-speed sampling cycle of 60 ms.
High Accuracy
Thermocouple/Pt input: ±0.1% of PV
Analog input: ±0.1% FS
Universal inputs on all models (thermocouple, PT, or analog
input) to handle various sensors with one Controller. Models also
available with Remote SP.
A PV/SV-status disp lay function can be set to automatically
alternate between displaying the status of the Temperature
Controller (auto/manual, RUN/STOP, and alarms) and the PV or SV.
Flexible contact outputs with logic operations (AND, OR, and
delays) set from the Support Software (CX-Thermo Ver. 4.0)
Preve ntive maintenanc e fo r rela ys in the T em p er at ur e Con tr oller
using a Control Output ON/OFF Counter.
Model available with position-prop ortional control
96 × 96 mm
E5AN-H 48 × 96 mm
E5EN-H
13
Solid State Relays for Heaters
Single-phase G3PE
Compact, Slim-profile SSRs with Heat
Sinks. Models with No Zero Cross for
a Wide Range of Applications.
RoHS compliant.
Models also available with no zero cross
Surge pass protection improved surge dielectric strength for
output currents. (OMRON testing)
Compact with a slim profile.
Mount to DIN Track or with screws.
Conforms to UL, CSA, and EN standards (TÜV certification).
Solid State Contactors for Heaters
Three-phase G3PE
Compact, Slim-profile SSRs with Heat Sinks.
Solid State Contactors for Three-phase
Heaters Reduced Installation Work with
DIN Track Mounting.
RoHS compliant.
Surge pass protection improved surge dielectric strength for
output currents. (OMRON testing)
Slim design with 3-phase output and built-in heat sinks.
DIN Track mounting types and screw mounting types are available.
All DIN Track mounting types mount to DIN Track
(applicable DIN Track: TR35-15Fe (IEC 60715)).
Conforms to UL, CSA, and EN standards (TÜV certification).
MEMO
14
Warranty and Application Considerations
Read and Understand This Catalog
Please read and understan d this catalog before purchasing the products. Please consult your OMRON representative if you
have any questions or comments.
Warranty and Limitat ions of Liability
WARRANTY
OMRON's e xclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or
other period if specified) from date of sale by OMRON.
OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT,
MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. ANY BUYER OR USER
A CKNO WLEDGES THAT THE B UYER OR USER ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET
THE REQUIREMENTS OF THEIR INTENDED USE. OMRON DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR
IMPLIED.
LIMITATIONS OF LIABILITY
OMRON SHALL NO T BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL D AMA GES, LOSS OF PR OFITS,
OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED ON
CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT LIABILITY.
In no e vent shall the responsibility of OMR ON for any act exceed the individual price of the product on which liability is asserted.
IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER CLAIMS REGARDING THE
PRODUCTS UNLESS OMRON'S ANALYSIS CONFIRMS THAT THE PRODUCTS WERE PROPERLY HANDLED, STORED,
INSTALLED, AND MAINTAINED AND NOT SUBJECT TO CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE
MODIFICATION OR REPAIR.
Application Considerations
SUITABILITY FOR USE
OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of
products in the customer's application or use of the products.
Take all necessary steps to determine the suitability of the product for the systems, machines, and equipment with which it will
be used.
Know and observe all prohibitions of use applicable to this product.
NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT
ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON
PRODUCTS ARE PR OPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR
SYSTEM.
Disclaimers
PERFORMANCE DATA
Performance data given in this catalog is provided as a guide for the user in determining suitability and does not constitute a
warranty. It may represent the result of OMRON's test conditions, and the users must correlate it to actual application
requirements. Actual performance is subject to the OMRON Warranty and Limitations of Liability.
CHANGE IN SPECIFICATIONS
Product specifications and accessories may be changed at any time based on improvements and other reasons. Consult with
your OMRON representative at any time to confir m actual specifications of purchased product.
DIMENSIONS AND WEIGHTS
Dimensions and weights are nominal and are not to be used for manufacturing purposes, even when tolerances are shown.
Authorized Distributor:
In the interest of product improvement,
specifications are subject to change without notice.
Cat. No. J176-E1-01 Printed in Japan
1008
© OMRON Corporation 2008 All Rights Reserved.
OMRON Corporation Industrial Automation Company
OMRON ELECTRONICS LLC
One Commerce Drive Schaumburg,
IL 60173-5302 U.S.A.
Tel: (1) 847-843-7900/Fax: (1) 847-843-7787
Regional Headquarters
OMRON EUROPE B.V.
Wegalaan 67-69-2132 JD Hoofddorp
The Netherlands
Tel: (31)2356-81-300/Fax: (31)2356-81-388
Contact: www.ia.omron.com
Tokyo, JAPAN
OMRON ASIA PACIFIC PTE. LTD.
No. 438A Alexandra Road # 05-05/08 (Lobby 2),
Alexandra Technopark,
Singapore 119967
Tel: (65) 6835-3011/Fax: (65) 6835-2711
OMRON (CHINA) CO., LTD.
Room 2211, Bank of China Tower,
200 Yin Cheng Zhong Road,
PuDong New Area, Shanghai, 200120, China
Tel: (86) 21-5037-2222/Fax: (86) 21-5037-2200
CSM_11_1_0514