HD74LS77 4-bit Bistable Latches REJ03D0418-0300 Rev.3.00 Jul.22.2005 The HD74LS77 is ideally suited for use as temporary storage for binary information between processing units and input / output or indicator units. Information present at a data (D) input is transferred to the Q output when the enable (G) is high and the Q output will follow the data input as long as the enable remains high. When the enable goes low, the information (that was present at the data input at the time the transition occurred) is retained at the Q output until the enable is permitted to go high. Features * Ordering Information Part Name Package Type HD74LS77FPEL SOP-14 pin (JEITA) Package Code (Previous Code) PRSP0014DF-B (FP-14DAV) Package Abbreviation Taping Abbreviation (Quantity) FP EL (2,000 pcs/reel) Pin Arrangement 1D 1 14 1Q 2 Q D G 2D 13 2Q Enable 3-4 3 D 12 Enable 1-2 VCC 4 11 GND 10 NC 9 3Q 8 4Q 3D 5 4D 6 NC 7 G Q Q D G D G Q (Top view) Function Table D Inputs G Outputs Q L H H H L H X H; high level, L; low level, X; irrelevant L Q0 Rev.3.00, Jul.22.2005, page 1 of 4 HD74LS77 Block Diagram (1/4) Data Q To Other Latch Enable Absolute Maximum Ratings Symbol Ratings Unit Supply voltage Input voltage Item VCC VIN 7 7 V V Power dissipation Storage temperature PT Tstg 400 -65 to +150 mW C Note: Voltage value, unless otherwise noted, are with respect to network ground terminal. Recommended Operating Conditions Item Symbol Min Typ Max Unit VCC IOH 4.75 -- 5.00 -- 5.25 -400 V A IOL Topr -- -20 -- 25 8 75 mA C Pulse width Setup time tw tsu 20 20 -- -- -- -- ns ns Hold time th 5 -- -- ns Supply voltage Output current Operating temperature Electrical Characteristics (Ta = -20 to +75 C) Item Input voltage Symbol min. typ.* max. Unit VIH VIL 2.0 -- -- -- -- 0.8 V V VOH 2.7 -- -- V -- -- 0.4 -- -- -- -- 0.5 20 -- -- -- -- 80 -0.4 -- -- -- -- -1.6 0.1 -- -- 0.4 IOS -20 -- ICC VIK -- -- 6.9 -- Output voltage VOL D Input current G D G D G Short-circuit output current Supply current** Input clamp voltage IIH IIL II V VCC = 4.75 V, VIH = 2 V, VIL = 0.8 V, IOH = -400 A IOL = 4 mA VCC = 4.75 V, VIH = 2 V, VIL = 0.8 V IOL = 8 mA A VCC = 5.25 V, VI = 2.7 V mA VCC = 5.25 V, VI = 0.4 V mA VCC = 5.25 V, VI = 7 V -100 mA VCC = 5.25 V 13 -1.5 mA V VCC = 5.25 V VCC = 4.75 V, IIN = -18 mA Notes: * VCC = 5 V, Ta = 25C ** ICC is measured with all outputs open and all inputs grounded. Rev.3.00, Jul.22.2005, page 2 of 4 Condition HD74LS77 Switching Characteristics (VCC = 5 V, Ta = 25C) Item Symbol tPLH Inputs Outputs D Q tPHL tPLH Propagation delay time G tPHL min. -- typ. 11 max. 19 -- -- 9 10 17 18 -- 10 18 Q Unit ns Condition CL = 15 pF, RL = 2 k Testing Method Test Circuit VCC Output Input RL P.G. Zout = 50 D Q Input CL P.G. Zout = 50 Notes: G 1. Test is put into the each latch. 2. CL includes probe and jig capacitance. 3. All diodes are 1S2074(H). Waveform 1s tTLH D 90% 1.3 V 1s tTHL 3V 90% 1.3 V 1.3 V 10% 10% tsu tTLH th tTHL 3V 90% 90% 1.3 V 1.3 V 10% 10% G 0V tsu th tw 1.3 V 1.3 V 0V tw tPLH VOH Q 1.3 V tPLH Notes: tPHL 1.3 V VOL tPHL 1. Input pulse; tTLH 10 ns, tTHL 10 ns. 2. When measuring propagation delay times from the D input, the corresponding G input must be held high. Rev.3.00, Jul.22.2005, page 3 of 4 HD74LS77 Package Dimensions JEITA Package Code P-SOP14-5.5x10.06-1.27 RENESAS Code PRSP0014DF-B *1 Previous Code FP-14DAV D MASS[Typ.] 0.23g NOTE) 1. DIMENSIONS"*1 (Nom)"AND"*2" DO NOT INCLUDE MOLD FLASH. 2. DIMENSION"*3"DOES NOT INCLUDE TRIM OFFSET. F 14 8 c HE *2 E bp Index mark Reference Symbol Terminal cross section ( Ni/Pd/Au plating ) 1 Z *3 Nom Max D 10.06 10.5 E 5.50 A2 7 e A1 bp Dimension in Millimeters Min x M 0.00 0.10 0.20 0.34 0.40 0.46 0.15 0.20 0.25 7.80 8.00 2.20 A L1 bp b1 c A c A1 y L Detail F 1 0 HE 7.50 1.27 e x 0.12 y 0.15 Z 1.42 0.50 L L Rev.3.00, Jul.22.2005, page 4 of 4 8 1 0.70 1.15 0.90 Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan Keep safety first in your circuit designs! 1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammable material or (iii) prevention against any malfunction or mishap. Notes regarding these materials 1. These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corp. product best suited to the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Renesas Technology Corp. or a third party. 2. Renesas Technology Corp. assumes no responsibility for any damage, or infringement of any third-party's rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application examples contained in these materials. 3. All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the time of publication of these materials, and are subject to change by Renesas Technology Corp. without notice due to product improvements or other reasons. It is therefore recommended that customers contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor for the latest product information before purchasing a product listed herein. The information described here may contain technical inaccuracies or typographical errors. Renesas Technology Corp. assumes no responsibility for any damage, liability, or other loss rising from these inaccuracies or errors. Please also pay attention to information published by Renesas Technology Corp. by various means, including the Renesas Technology Corp. Semiconductor home page (http://www.renesas.com). 4. When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms, please be sure to evaluate all information as a total system before making a final decision on the applicability of the information and products. Renesas Technology Corp. assumes no responsibility for any damage, liability or other loss resulting from the information contained herein. 5. Renesas Technology Corp. semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake. Please contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor when considering the use of a product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use. 6. The prior written approval of Renesas Technology Corp. is necessary to reprint or reproduce in whole or in part these materials. 7. If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination. Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited. 8. Please contact Renesas Technology Corp. for further details on these materials or the products contained therein. http://www.renesas.com RENESAS SALES OFFICES Refer to "http://www.renesas.com/en/network" for the latest and detailed information. Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.S.A Tel: <1> (408) 382-7500, Fax: <1> (408) 382-7501 Renesas Technology Europe Limited Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K. Tel: <44> (1628) 585-100, Fax: <44> (1628) 585-900 Renesas Technology Hong Kong Ltd. 7th Floor, North Tower, World Finance Centre, Harbour City, 1 Canton Road, Tsimshatsui, Kowloon, Hong Kong Tel: <852> 2265-6688, Fax: <852> 2730-6071 Renesas Technology Taiwan Co., Ltd. 10th Floor, No.99, Fushing North Road, Taipei, Taiwan Tel: <886> (2) 2715-2888, Fax: <886> (2) 2713-2999 Renesas Technology (Shanghai) Co., Ltd. Unit2607 Ruijing Building, No.205 Maoming Road (S), Shanghai 200020, China Tel: <86> (21) 6472-1001, Fax: <86> (21) 6415-2952 Renesas Technology Singapore Pte. Ltd. 1 Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632 Tel: <65> 6213-0200, Fax: <65> 6278-8001 Renesas Technology Korea Co., Ltd. Kukje Center Bldg. 18th Fl., 191, 2-ka, Hangang-ro, Yongsan-ku, Seoul 140-702, Korea Tel: <82> 2-796-3115, Fax: <82> 2-796-2145 Renesas Technology Malaysia Sdn. Bhd. Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No.18, Jalan Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia Tel: <603> 7955-9390, Fax: <603> 7955-9510 (c) 2005. Renesas Technology Corp., All rights reserved. Printed in Japan. Colophon .3.0