MP12 SERIES Metallized Polypropylene Metallized Polypropylene Wrap and Epoxy End Fill Where high insulation resistance, high Q, extreme stability, close tolerance, low dielectric absorption and dissipation factor are required. FEATURES - High Insulation Resistance - Extreme Stability - Close Tolerance STANDARD CONFIGURATION - Wrap and Epoxy End Fill Rev. 2 Specification Summary Quality Control Capacitors are tested 100% for: Capacitance Range 0.01F to 10.0F Capacitance Tolerance Standard tolerance is 10%. Tolerances of 20%,5%,2%,1% are available. Operating Temperature Range -55C to +105C o Capacitance o Tolerance o Dissipation Factor o Dielectric withstanding voltage o Insulation Resistance o Equivalent Series Resistance (ESR) Enclosure/ Construction Plastic film case with epoxy end seal. Process and inspection data are maintained on file and available on special request. Voltage Rating 150VDC to 600VDC Environmental Parameter Vibration Immersion Shock Humidity Thermal Shock Life Method 204 104 213 106 107 108 Reference MIL-STD-202 Condition D B I A F Characteristics Insulation Resistance Temperature(C) 25 Megaohmsx 300,000 Microfarads 85 30,000 105 3,000 Insulation Resistance Capacitance Change Temperature(C) -55 PercentageChange 2 (typical) 25 0 105 -4 CapacitanceChange Dissipation Factor When measured at the frequency specified for capacitance measurement, the dissipation factor shall not exceed 0.1%. Dielectric Strength Capacitors shall withstand a DC potential of twice rated voltage for one minute through a limiting resistance of 100 ohms/volt without damage or breakdown. Rev. 2 ELECTRICAL EC PART NUMBER CAP uF MP12_103_ MP12_123_ MP12_153_ MP12_183_ MP12_223_ MP12_273_ MP12_333_ MP12_393_ MP12_473_ MP12_563_ MP12_683_ MP12_823_ MP12_104_ MP12_124_ MP12_154_ MP12_184_ MP12_224_ MP12_274_ MP12_334_ MP12_394_ MP12_474_ MP12_564_ MP12_684_ MP12_824_ MP12_105_ MP12_125_ MP12_155_ MP12_205_ MP12_305_ MP12_405_ MP12_505_ MP12_605_ MP12_805_ MP12_905_ MP12_106_ 0.010 0.012 0.015 0.018 0.022 0.027 0.033 0.039 0.047 0.056 0.068 0.082 0.100 0.120 0.150 0.180 0.220 0.270 0.330 0.390 0.470 0.560 0.680 0.820 1.000 1.250 1.500 2.000 3.000 4.000 5.000 6.000 8.000 9.000 10.000 DATA 150 VDC 200 VDC 300 VDC 400 VDC 600 VDC E F H J K D L AWG D L AWG D L AWG D L AWG D L AWG 0.187 0.500 24 0.187 0.500 24 0.187 0.500 24 0.187 0.500 24 0.250 0.625 24 0.187 0.500 24 0.187 0.500 24 0.187 0.500 24 0.187 0.500 24 0.265 0.625 22 0.187 0.500 24 0.187 0.500 24 0.187 0.500 24 0.203 0.500 24 0.296 0.625 22 0.187 0.500 24 0.187 0.500 24 0.203 0.500 24 0.234 0.500 24 0.328 0.625 22 0.187 0.500 24 0.187 0.500 24 0.218 0.500 24 0.250 0.500 24 0.312 0.750 22 0.187 0.500 24 0.187 0.500 24 0.234 0.500 24 0.281 0.500 22 0.343 0.750 22 0.187 0.500 24 0.187 0.500 24 0.265 0.500 22 0.296 0.500 22 0.375 0.750 22 0.187 0.500 24 0.203 0.500 24 0.281 0.500 22 0.250 0.625 24 0.406 0.750 22 0.187 0.500 24 0.234 0.500 24 0.250 0.625 24 0.281 0.625 22 0.390 0.875 22 0.203 0.500 24 0.250 0.500 24 0.265 0.625 22 0.312 0.625 22 0.359 1.062 22 0.218 0.500 24 0.265 0.500 22 0.296 0.625 22 0.328 0.625 22 0.375 1.062 22 0.234 0.500 24 0.234 0.625 24 0.312 0.625 22 0.296 0.750 22 0.421 1.187 22 0.250 0.500 24 0.265 0.625 22 0.281 0.750 22 0.328 0.750 22 0.468 1.187 20 0.265 0.500 22 0.375 0.625 22 0.312 0.750 22 0.359 0.750 22 0.500 1.187 20 0.250 0.625 22 0.265 0.750 22 0.343 0.750 22 0.390 0.750 22 0.562 1.187 20 0.265 0.625 22 0.281 0.750 22 0.359 0.875 22 0.359 1.062 22 0.546 1.437 20 0.296 0.625 22 0.312 0.750 22 0.390 0.875 22 0.406 1.062 22 0.593 1.437 20 0.312 0.625 22 0.343 0.750 22 0.437 0.875 22 0.437 1.062 22 0.656 1.437 20 0.312 0.750 22 0.390 0.750 22 0.500 0.875 20 0.484 1.062 20 0.718 1.437 20 0.328 0.750 22 0.375 0.875 22 0.515 0.875 20 0.531 1.062 20 0.781 1.437 20 0.359 0.750 22 0.406 0.875 22 0.468 1.187 20 0.531 1.187 20 0.781 1.687 20 0.390 0.750 22 0.437 0.875 22 0.515 1.187 20 0.578 1.187 20 0.859 1.687 20 0.390 0.875 22 0.406 1.187 22 0.562 1.187 20 0.640 1.187 20 0.937 1.687 20 0.375 1.062 22 0.437 1.187 22 0.562 1.437 20 0.625 1.437 20 0.937 1.937 20 0.421 1.062 22 0.531 1.187 20 0.609 1.437 20 0.687 1.437 20 1.031 1.937 20 0.468 1.062 20 0.562 1.187 20 0.671 1.437 20 0.687 1.687 20 1.093 2.187 20 0.500 1.062 20 0.531 1.437 20 0.734 1.437 20 0.750 1.687 20 1.187 2.187 20 0.531 1.187 20 0.604 1.437 20 0.950 1.687 20 0.859 1.687 20 1.375 2.187 20 0.578 1.437 20 0.718 1.437 20 0.921 1.687 20 0.968 1.937 20 0.656 1.437 20 0.765 1.687 20 0.906 2.187 20 1.250 1.937 20 0.671 1.687 20 0.843 1.687 20 1.031 2.187 20 1.140 2.187 20 0.734 1.687 20 0.859 1.937 20 1.125 2.187 20 1.250 2.187 20 0.781 1.937 20 0.953 1.937 20 1.312 2.187 20 0.812 1.937 20 1.031 1.937 20 0.859 1.937 20 1.109 1.937 20 - Note: The fifth character of the part number represents DC voltage rating: (E=150 VDC, F=200 VDC, etc.) Additionally, the tenth character represents the capacitance tolerance: M=20%, K=10%, J=5%, F=1%. *The lead length is 1.5" minimum. The lead material is copper clad steel, solder coated. * Rev. 2 MECHANICAL DATA Tolerances: Length: +3/32", -1/6" Diameter: 0.249" andunder+/-0.032" 0.250" to 0.500" +/-0.046" 0.501" andover +/-0.062" Rev. 2 ADDITIONAL INFORMATION Among these in type MP12 metallized polypropylene precision capacitors which exhibit unique and outstanding electrical and environmental characteristics. The following are some of the most significant. Negligible shift in capacitance under long term exposure to humidity, operating life and temperature cycling. - Insulation resistance, dielectric absorption and dissipation factor properties are all equivalent, or superior, to those of polystyrene. Small size and weight savings equivalent to those of metallized polycarbonate capacitors, make type MP12 ideal for precision instruments, communications, and high density circuitry applications. Polypropylene capacitors are excellent for all critical applications which require high insulation resistance, high Q, extreme stability, close tolerance, low dielectric absorption and dissipation factor. The temperature coefficient makes an excellent choice for high Q tuned circuits, precision filter circuits, pulse networks and RC circuits. HOW TO ORDER TYPE MP Metallized Polypropylene STYLE/TERMINAL/VOLTAGE The first number represents the style. The second number represents Terminals and the third letter represents Voltage. 12E Expressed in picofarads, the first two digits are significant figure, The third is the number of zeros. (e.g. 104 equals 100000pF) 104 CAPACITANCE IN PICOFARADS TOLERANCE K M=20%, K=10%, J=5%, G=2%, F=1% Marking and Date Code All capacitors are marked with company initials "EC", corporate logo or EC trademark--in addition to type MP12, capacitance, tolerance, rated DC working voltage and date code. The first two digits of the date code represent the year, the second two digits the week, i.e., 0952 is the 52nd week of 2009, 0902 is the second week of 2009. Quality Assurance Major emphasis is placed on quality assurance. EC is an ISO 9001-2000 and AS9100:2004 Certified Company. Raw material inspection and the use of SPC manufacturing procedures assure the highest quality standards. Procedures are fully described in the EC Quality Control Manual. Electronic Concepts will continue to advance the state-of-the-art by utilizing leading edge technology, compact capacitor designs and establishing reliability procedures. Sales Offices United States Europe Eastern: *Headquarters* P.O. Box 1278 Eatontown,NJ 07724 Tel: 732-542-7880 Fax: 732-542-0524 Central: Illinois 630-668-8747 email: sales@ecicaps.com website:www.ecicaps.com Ireland Electronic ConceptsEurope LTD IDA Estate, Oughterad Co. Galway, Ireland tel: +353-91-552385,552432 fax: +353-91-552387 email: sales@ecicaps.ie website:www.electronicconcepts.ie Rev. 2