Please note that Cypress is an Infineon Technologies Company. The document following this cover page is marked as "Cypress" document as this is the company that originally developed the product. Please note that Infineon will continue to offer the product to new and existing customers as part of the Infineon product portfolio. Continuity of document content The fact that Infineon offers the following product as part of the Infineon product portfolio does not lead to any changes to this document. Future revisions will occur when appropriate, and any changes will be set out on the document history page. Continuity of ordering part numbers Infineon continues to support existing part numbers. Please continue to use the ordering part numbers listed in the datasheet for ordering. www.infineon.com FM25V02A 256-Kbit (32K x 8) Serial (SPI) F-RAM 256-Kbit (32K x 8) Serial (SPI) F-RAM Features Functional Description 256-Kbit ferroelectric random access memory (F-RAM) logically organized as 32K x 8 14 High-endurance 100 trillion (10 ) read/writes 151-year data retention (See Data Retention and Endurance on page 14) NoDelayTM writes Advanced high-reliability ferroelectric process Very fast serial peripheral interface (SPI) Up to 40-MHz frequency Direct hardware replacement for serial flash and EEPROM Supports SPI mode 0 (0, 0) and mode 3 (1, 1) Sophisticated write-protection scheme Hardware protection using the Write Protect (WP) pin Software protection using Write Disable instruction Software block protection for 1/4, 1/2, or entire array Device ID Manufacturer ID and Product ID Low power consumption 2.5-mA active current at 40 MHz 150-A standby current 8-A sleep mode current Low-voltage operation: VDD = 2.0 V to 3.6 V Industrial temperature: -40 C to +85 C Packages 8-pin small outline integrated circuit (SOIC) package 8-pin dual flat no-leads (DFN) package Restriction of hazardous substances (RoHS) compliant The FM25V02A is a 256-Kbit nonvolatile memory employing an advanced ferroelectric process. An F-RAM is nonvolatile and performs reads and writes similar to a RAM. It provides reliable data retention for 151 years while eliminating the complexities, overhead, and system-level reliability problems caused by serial flash, EEPROM, and other nonvolatile memories. Unlike serial flash and EEPROM, the FM25V02A performs write operations at bus speed. No write delays are incurred. Data is written to the memory array immediately after each byte is successfully transferred to the device. The next bus cycle can commence without the need for data polling. In addition, the product offers substantial write endurance compared with other nonvolatile memories. The FM25V02A is capable of supporting 1014 read/write cycles, or 100 million times more write cycles than EEPROM. These capabilities make the FM25V02A ideal for nonvolatile memory applications requiring frequent or rapid writes. Examples range from data logging, where the number of write cycles may be critical, to demanding industrial controls where the long write time of serial flash or EEPROM can cause data loss. The FM25V02A provides substantial benefits to users of serial EEPROM or flash as a hardware drop-in replacement. The FM25V02A uses the high-speed SPI bus, which enhances the high-speed write capability of F-RAM technology. The device incorporates a read-only Device ID that allows the host to determine the manufacturer, product density, and product revision. The device specifications are guaranteed over an industrial range of -40 C to +85 C. For a complete list of related resources, click here. Logic Block Diagram WP Instruction Decoder Clock Generator Control Logic Write Protect CS HOLD SCK 32 K x 8 F-RAM Array Instruction Register 15 Address Register Counter SI 8 Data I/O Register SO 3 Nonvolatile Status Register Cypress Semiconductor Corporation Document Number: 001-90865 Rev. *I * 198 Champion Court * San Jose, CA 95134-1709 * 408-943-2600 Revised December 7, 2018 FM25V02A Contents Pinouts .............................................................................. 3 Pin Definitions .................................................................. 3 Functional Overview ........................................................ 4 Memory Architecture ........................................................ 4 Serial Peripheral Interface - SPI Bus .............................. 4 SPI Overview ............................................................... 4 SPI Modes ................................................................... 5 Power-Up to First Access ............................................ 6 Command Structure .................................................... 6 WREN - Set Write Enable Latch ................................. 6 WRDI - Reset Write Enable Latch ............................... 6 Status Register and Write Protection ............................. 7 RDSR - Read Status Register ..................................... 7 WRSR - Write Status Register .................................... 7 Memory Operation ............................................................ 8 Write Operation ........................................................... 8 Read Operation ........................................................... 8 Fast Read Operation ................................................... 8 HOLD Pin Operation ................................................. 10 Sleep Mode ............................................................... 10 Device ID ................................................................... 11 Endurance ................................................................. 12 Document Number: 001-90865 Rev. *I Maximum Ratings ........................................................... 13 Operating Range ............................................................. 13 DC Electrical Characteristics ........................................ 13 Data Retention and Endurance ..................................... 14 Capacitance .................................................................... 14 Thermal Resistance ........................................................ 14 AC Test Conditions ........................................................ 14 AC Switching Characteristics ....................................... 15 Power Cycle Timing ....................................................... 17 Ordering Information ...................................................... 18 Ordering Code Definitions ......................................... 18 Package Diagrams .......................................................... 19 Acronyms ........................................................................ 21 Document Conventions ................................................. 21 Units of Measure ....................................................... 21 Document History Page ................................................. 22 Sales, Solutions, and Legal Information ...................... 24 Worldwide Sales and Design Support ....................... 24 Products .................................................................... 24 PSoC(R) Solutions ...................................................... 24 Cypress Developer Community ................................. 24 Technical Support ..................................................... 24 Page 2 of 24 FM25V02A Pinouts Figure 1. 8-pin SOIC Pinout CS 1 SO 2 WP 3 VSS 4 Top View not to scale 8 VDD 7 HOLD 6 SCK 5 SI Figure 2. 8-pin DFN Pinout O CS 1 SO 2 8 VDD 7 HOLD EXPOSED PAD WP 3 6 SCK VSS 4 5 SI Top View not to scale Pin Definitions Pin Name I/O Type Description SCK Input Serial Clock. All I/O activity is synchronized to the serial clock. Inputs are latched on the rising edge and outputs occur on the falling edge. Because the device is synchronous, the clock frequency may be any value between 0 and 40 MHz and may be interrupted at any time. CS Input Chip Select. This active LOW input activates the device. When HIGH, the device enters the low-power standby mode, ignores other inputs, and the output is tristated. When LOW, the device internally activates the SCK signal. A falling edge on CS must occur before every opcode. SI[1] Input Serial Input. All data is input to the device on this pin. The pin is sampled on the rising edge of SCK and is ignored at other times. It should always be driven to a valid logic level to meet IDD specifications. SO[1] Output Serial Output. This is the data output pin. It is driven during a read and remains tristated at all other times including when HOLD is LOW. Data transitions are driven on the falling edge of the serial clock. WP Input Write Protect. This active LOW pin prevents write operation to the Status Register when WPEN is set to `1'. This is critical because other write protection features are controlled through the Status Register. A complete explanation of write protection is provided on Status Register and Write Protection on page 7. This pin must be tied to VDD if not used. HOLD Input HOLD Pin. The HOLD pin is used when the host CPU must interrupt a memory operation for another task. When HOLD is LOW, the current operation is suspended. The device ignores any transition on SCK or CS. All transitions on HOLD must occur while SCK is LOW. This pin has a weak internal pull-up (refer to the RIN spec in DC Electrical Characteristics). VSS Power supply Ground for the device. Must be connected to the ground of the system. VDD Power supply Power supply input to the device. EXPOSED PAD No connect The EXPOSED PAD on the bottom of 8-pin DFN package is not connected to the die. The EXPOSED PAD should not be soldered on the PCB. Note 1. SI may be connected to SO for a single pin data interface. Document Number: 001-90865 Rev. *I Page 3 of 24 FM25V02A Functional Overview The FM25V02A is a serial F-RAM memory. The memory array is logically organized as 32,768 x 8 bits and is accessed using an industry-standard serial peripheral interface (SPI) bus. The functional operation of the F-RAM is similar to serial flash and serial EEPROMs. The major difference between the FM25V02A and a serial flash or EEPROM with the same pinout is the F-RAM's superior write performance, high endurance, and low power consumption. Memory Architecture When accessing the FM25V02A, the user addresses 32K locations of eight data bits each. These eight data bits are shifted in or out serially. The addresses are accessed using the SPI protocol, which includes a chip select (to permit multiple devices on the bus), an opcode, and a two-byte address. The upper bit of the address range is `don't care' value. The complete address of 15 bits specifies each byte address uniquely. Most functions of the FM25V02A are either controlled by the SPI interface or are handled by on-board circuitry. The access time for the memory operation is essentially zero, beyond the time needed for the serial protocol. That is, the memory is read or written at the speed of the SPI bus. Unlike a serial flash or EEPROM, it is not necessary to poll the device for a ready condition because writes occur at bus speed. By the time a new bus transaction can be shifted into the device, a write operation is complete. This is explained in more detail in Memory Operation on page 8. Serial Peripheral Interface - SPI Bus The FM25V02A is a SPI slave device and operates at speeds up to 40 MHz. This high-speed serial bus provides high-performance serial communication to a SPI master. Many common microcontrollers have hardware SPI ports allowing a direct interface. It is quite simple to emulate the port using ordinary port pins for microcontrollers that do not. The FM25V02A operates in SPI Mode 0 and 3. SPI Overview The SPI is a four-pin interface with Chip Select (CS), Serial Input (SI), Serial Output (SO), and Serial Clock (SCK) pins. The SPI is a synchronous serial interface, which uses clock and data pins for memory access and supports multiple devices on the data bus. A device on the SPI bus is activated using the CS pin. The relationship between chip select, clock, and data is dictated by the SPI mode. This device supports SPI modes 0 and 3. In both of these modes, data is clocked into the F-RAM on the rising edge of SCK starting from the first rising edge after CS goes active. The SPI protocol is controlled by opcodes. These opcodes specify the commands from the bus master to the slave device. After CS is activated, the first byte transferred from the bus Document Number: 001-90865 Rev. *I master is the opcode. Following the opcode, any addresses and data are then transferred. The CS must go inactive after an operation is complete and before a new opcode can be issued. The commonly used terms in the SPI protocol are as follows: SPI Master The SPI master device controls the operations on a SPI bus. An SPI bus may have only one master with one or more slave devices. All the slaves share the same SPI bus lines and the master may select any of the slave devices using the CS pin. All of the operations must be initiated by the master activating a slave device by pulling the CS pin of the slave LOW. The master also generates the SCK and all the data transmission on SI and SO lines are synchronized with this clock. SPI Slave The SPI slave device is activated by the master through the Chip Select line. A slave device gets the SCK as an input from the SPI master and all the communication is synchronized with this clock. An SPI slave never initiates a communication on the SPI bus and acts only on the instruction from the master. The FM25V02A operates as an SPI slave and may share the SPI bus with other SPI slave devices. Chip Select (CS) To select any slave device, the master needs to pull down the corresponding CS pin. Any instruction can be issued to a slave device only while the CS pin is LOW. When the device is not selected, data through the SI pin is ignored and the serial output pin (SO) remains in a high-impedance state. Note A new instruction must begin with the falling edge of CS. Therefore, only one opcode can be issued for each active Chip Select cycle. Serial Clock (SCK) The serial clock is generated by the SPI master and the communication is synchronized with this clock after CS goes LOW. The FM25V02A enables SPI modes 0 and 3 for data communication. In both of these modes, the inputs are latched by the slave device on the rising edge of SCK and outputs are issued on the falling edge. Therefore, the first rising edge of SCK signifies the arrival of the first bit (MSB) of a SPI instruction on the SI pin. Further, all data inputs and outputs are synchronized with SCK. Data Transmission (SI/SO) The SPI data bus consists of two lines, SI and SO, for serial data communication. SI is also referred to as Master Out Slave In (MOSI) and SO is referred to as Master In Slave Out (MISO). The master issues instructions to the slave through the SI pin, while the slave responds through the SO pin. Multiple slave devices may share the SI and SO lines as described earlier. The FM25V02A has two separate pins for SI and SO, which can be connected with the master as shown in Figure 3 on page 5. Page 4 of 24 FM25V02A For a microcontroller that has no dedicated SPI bus, a general-purpose port may be used. To reduce hardware resources on the controller, it is possible to connect the two data pins (SI, SO) together and tie off (HIGH) the HOLD and WP pins. Figure 4 shows such a configuration, which uses only three pins. Serial Opcode After the slave device is selected with CS going LOW, the first byte received is treated as the opcode for the intended operation. FM25V02A uses the standard opcodes for memory accesses. Invalid Opcode Most Significant Bit (MSB) If an invalid opcode is received, the opcode is ignored and the device ignores any additional serial data on the SI pin until the next falling edge of CS, and the SO pin remains tristated. The SPI protocol requires that the first bit to be transmitted is the Most Significant Bit (MSB). This is valid for both address and data transmission. Status Register The 256-Kbit serial F-RAM requires a 2-byte address for any read or write operation. Because the address is only 15 bits, the upper bit which is fed in is ignored by the device. Although the upper bit is `don't care', Cypress recommends that these bits be set to 0s to enable seamless transition to higher memory densities. FM25V02A has an 8-bit Status Register. The bits in the Status Register are used to configure the device. These bits are described in Table 3 on page 7. Figure 3. System Configuration with SPI Port SCK MOSI MISO SCK SPI Microcontroller SI SO FM25V02A CS HOLD WP SCK SI SO FM25V02A CS HOLD WP CS1 HO LD 1 WP1 CS2 HO LD 2 WP2 Figure 4. System Configuration Without SPI Port P1.0 P1.1 SCK SI SO Microcontroller FM25V02A CS HOLD WP P1.2 SPI Modes SPI Mode 0 (CPOL = 0, CPHA = 0) active. If the clock starts from a HIGH state (in mode 3), the first rising edge after the clock toggles is considered. The output data is available on the falling edge of SCK.The two SPI modes are shown in Figure 5 on page 6 and Figure 6 on page 6. The status of the clock when the bus master is not transferring data is: SPI Mode 3 (CPOL = 1, CPHA = 1) SCK remains at 0 for Mode 0 SCK remains at 1 for Mode 3 FM25V02A may be driven by a microcontroller with its SPI peripheral running in either of the following two modes: For both these modes, the input data is latched in on the rising edge of SCK starting from the first rising edge after CS goes Document Number: 001-90865 Rev. *I Page 5 of 24 FM25V02A The device detects the SPI mode from the status of the SCK pin when the device is selected by bringing the CS pin LOW. If the SCK pin is LOW when the device is selected, SPI Mode 0 is assumed and if the SCK pin is HIGH, it works in SPI Mode 3. Figure 5. SPI Mode 0 1 2 3 5 4 6 7 SCK SI 7 6 5 4 3 2 1 0 MSB The FM25V02A will power up with writes disabled. The WREN command must be issued before any write operation. Sending the WREN opcode allows the user to issue subsequent opcodes for write operations. These include writing the Status Register (WRSR) and writing the memory (WRITE). Sending the WREN opcode causes the internal Write Enable Latch to be set. A flag bit in the Status Register, called WEL, indicates the state of the latch. WEL = `1' indicates that writes are permitted. Attempting to write the WEL bit in the Status Register has no effect on the state of this bit - only the WREN opcode can set this bit. The WEL bit will be automatically cleared on the rising edge of CS following a WRDI, a WRSR, or a WRITE operation. This prevents further writes to the Status Register or the F-RAM array without another WREN command. Figure 7 illustrates the WREN command bus configuration. CS 0 WREN - Set Write Enable Latch LSB Figure 6. SPI Mode 3 Figure 7. WREN Bus Configuration CS 0 1 2 3 4 5 6 7 CS 0 SCK 1 2 3 4 5 6 7 SCK SI 7 6 5 4 3 MSB 2 1 0 The FM25V02A is not accessible for a tPU time after power-up. Users must comply with the timing parameter tPU, which is the minimum time from VDD (min) to the first CS LOW. Command Structure There are nine commands, called opcodes, that can be issued by the bus master to the FM25V02A. They are listed in Table 1. These opcodes control the functions performed by the memory. Table 1. Opcode Commands Description 0 0 0 Opcode WREN Set write enable latch 0000 0110b WRDI Reset write enable latch 0000 0100b RDSR Read Status Register 0000 0101b WRSR Write Status Register 0000 0001b READ Read memory data 0000 0011b FSTRD Fast read memory data 0000 1011b WRITE Write memory data 0000 0010b SLEEP Enter sleep mode 1011 1001b RDID Read device ID 1001 1111b Reserved Reserved 1100 0011b 0 1 1 0 HI-Z SO Power-Up to First Access Name 0 SI LSB WRDI - Reset Write Enable Latch The WRDI command disables all write activity by clearing the Write Enable Latch. The user can verify that writes are disabled by reading the WEL bit in the Status Register and verifying that WEL is equal to `0'. Figure 8 illustrates the WRDI command bus configuration. Figure 8. WRDI Bus Configuration CS 0 1 2 3 4 5 6 7 SCK SI SO 0 0 0 0 0 1 0 0 HI-Z 1100 0010b 0101 1010b 0101 1011b Document Number: 001-90865 Rev. *I Page 6 of 24 FM25V02A Status Register and Write Protection The write protection features of the FM25V02A are multi-tiered and are enabled through the status register. The status register is organized as follows (the default value shipped from the factory for bits in the status register is `0'): Table 2. Status Register Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 WPEN (0) X (0) X (0) X (0) BP1 (0) BP0 (0) WEL (0) X (0) Table 3. Status Register Bit Definition Bit Definition Description Bit 0 Don't care This bit is non-writable and always returns `0' upon read. Bit 1 (WEL) Write Enable WEL indicates if the device is write enabled. This bit defaults to `0' (disabled) on power-up. WEL = `1' --> Write enabled WEL = `0' --> Write disabled Bit 2 (BP0) Block Protect bit `0' Used for block protection. For details, see Table 4 on page 7. Bit 3 (BP1) Block Protect bit `1' Used for block protection. For details, see Table 4 on page 7. Bit 4-6 Don't care These bits are non-writable and always return `0' upon read. Bit 7 (WPEN) Write Protect Enable bit Used to enable the function of Write Protect Pin (WP). For details, see Table 5 on page 7. Bits 0 and 4-6 are fixed at `0'; none of these bits can be modified. Note that bit 0 ("Ready or Write in progress" bit in serial flash and EEPROM) is unnecessary, as the F-RAM writes in real-time and is never busy, so it reads out as a `0'. An exception to this is when the device is waking up from sleep mode, which is described in Sleep Mode on page 10. The BP1 and BP0 control the software write-protection features and are nonvolatile bits. The WEL flag indicates the state of the Write Enable Latch. Attempting to directly write the WEL bit in the Status Register has no effect on its state. This bit is internally set and cleared via the WREN and WRDI commands, respectively. BP1 and BP0 are memory block write protection bits. They specify portions of memory that are write-protected as shown in Table 4. Table 4. Block Memory Write Protection BP1 BP0 Protected Address Range 0 0 None 0 1 6000h to 7FFFh (upper 1/4) 1 0 4000h to 7FFFh (upper 1/2) 1 1 0000h to 7FFFh (all) The BP1 and BP0 bits and the Write Enable Latch are the only mechanisms that protect the memory from writes. The remaining write protection features protect inadvertent changes to the block protect bits. The write protect enable bit (WPEN) in the Status Register controls the effect of the hardware write protect (WP) pin. When the WPEN bit is set to `0', the status of the WP pin is ignored. When the WPEN bit is set to `1', a LOW on the WP pin inhibits a Document Number: 001-90865 Rev. *I write to the Status Register. Thus the Status Register is write-protected only when WPEN = `1' and WP = `0'. Table 5 summarizes the write protection conditions. Table 5. Write Protection Unprotected WEL WPEN WP Protected Blocks Blocks Status Register 0 X X Protected Protected Protected 1 0 X Protected Unprotected Unprotected 1 1 0 Protected Unprotected Protected 1 1 1 Protected Unprotected Unprotected RDSR - Read Status Register The RDSR command allows the bus master to verify the contents of the Status Register. Reading the status register provides information about the current state of the write-protection features. Following the RDSR opcode, the FM25V02A will return one byte with the contents of the Status Register. WRSR - Write Status Register The WRSR command allows the SPI bus master to write into the Status Register and change the write protect configuration by setting the WPEN, BP0, and BP1 bits as required. Prior to issuing a WRSR command, the WP pin must be HIGH or inactive. Note that on the FM25V02A, WP only prevents writing to the Status Register, not the memory array. Before sending the WRSR command, the user must send a WREN command to enable writes. Executing a WRSR command is a write operation and therefore, clears the Write Enable Latch. Page 7 of 24 FM25V02A Figure 9. RDSR Bus Configuration CS 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 SCK Opcode 0 SI 0 0 0 0 1 0 1 0 Data HI-Z SO D7 D6 D5 D4 D3 D2 D1 D0 MSB LSB Figure 10. WRSR Bus Configuration (WREN not shown) CS 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 SCK Data Opcode SI SO 0 0 0 0 0 0 0 1 D7 X MSB X D3 D2 X X LSB HI-Z Memory Operation The SPI interface, which is capable of a high clock frequency, highlights the fast write capability of the F-RAM technology. Unlike serial flash and EEPROMs, the FM25V02A can perform sequential writes at bus speed. No page register is needed and any number of sequential writes may be performed. Write Operation All writes to the memory begin with a WREN opcode with CS being asserted and deasserted. The next opcode is WRITE. The WRITE opcode is followed by a two-byte address containing the 15-bit address (A14-A0) of the first data byte to be written into the memory. The upper bit of the two-byte address is ignored. Subsequent bytes are data bytes, which are written sequentially. Addresses are incremented internally as long as the bus master continues to issue clocks and keeps CS LOW. If the last address of 7FFFh is reached, the counter will roll over to 0000h. Data is written MSB first. The rising edge of CS terminates a write operation. A write operation is shown in Figure 11 on page 9. Note When a burst write reaches a protected block address, the automatic address increment stops and all the subsequent data bytes received for write will be ignored by the device. EEPROMs use page buffers to increase their write throughput. This compensates for the technology's inherently slow write operations. F-RAM memories do not have page buffers because each byte is written to the F-RAM array immediately after it is Document Number: 001-90865 Rev. *I X clocked in (after the eighth clock). This allows any number of bytes to be written without page buffer delays. Note If the power is lost in the middle of the write operation, only the last completed byte will be written. Read Operation After the falling edge of CS, the bus master can issue a READ opcode. Following the READ command is a two-byte address containing the 15-bit address (A14-A0) of the first byte of the read operation. The upper bit of the address is ignored. After the opcode and address are issued, the device drives out the read data on the next eight clocks. The SI input is ignored during read data bytes. Subsequent bytes are data bytes, which are read out sequentially. Addresses are incremented internally as long as the bus master continues to issue clocks and CS is LOW. If the last address of 7FFFh is reached, the counter will roll over to 0000h. Data is read MSB first. The rising edge of CS terminates a read operation and tristates the SO pin. A read operation is shown in Figure 12 on page 9. Fast Read Operation The FM25V02A supports a FAST READ opcode (0Bh) that is provided for code compatibility with serial flash devices. The FAST READ opcode is followed by a two-byte address containing the 15-bit address (A14-A0) of the first byte of the read operation and then a dummy byte. The dummy byte inserts a read latency of an 8-clock cycle. The fast read operation is Page 8 of 24 FM25V02A otherwise the same as an ordinary read operation except that it requires an additional dummy byte. After receiving the opcode, address, and a dummy byte, the FM25V02A starts driving its SO line with data bytes, with the MSB first, and continues transmitting as long as the device is selected and the clock is available. In case of bulk read, the internal address counter is incremented automatically, and after the last address 7FFFh is reached, the counter rolls over to 0000h. When the device is driving data on its SO line, any transition on its SI line is ignored. The rising edge of CS terminates a fast read operation and tristates the SO pin. A Fast Read operation is shown in Figure 13. Figure 11. Memory Write (WREN not shown) Operation CS 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 SCK Opcode 0 SI 0 0 0 0 ~ ~ ~ ~ 0 12 13 14 15 0 1 1 0 X A14 A13 A12 A11 A10 A9 A8 MSB 3 4 5 6 7 Data 15-bit Address 0 2 A3 A2 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0 LSB MSB LSB HI-Z SO Figure 12. Memory Read Operation CS 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 SCK Opcode 0 SI 0 0 0 ~ ~ ~ ~ 0 12 13 14 15 0 1 2 3 4 5 6 7 15-bit Address 0 0 1 1 X A14 A13 A12 A11 A10 A9 A8 MSB A3 A2 A1 A0 LSB Data HI-Z SO D7 D6 D5 D4 D3 D2 D1 D0 MSB LSB Figure 13. Fast Read Operation CS 1 2 3 4 5 6 7 0 1 2 3 4 SCK Opcode SI 0 0 0 0 1 5 6 7 ~ ~ ~ ~ 0 12 13 14 15 16 17 18 19 20 21 22 23 0 1 1 X A14 A13 A12 A11 A10 A9 A8 MSB SO HI-Z A3 A2 A1 A0 X X X X X X X 3 4 5 6 7 X LSB Data D7 D6 D5 D4 D3 D2 D1 D0 MSB Document Number: 001-90865 Rev. *I 2 Dummy Byte 15-bit Address 0 1 LSB Page 9 of 24 FM25V02A HOLD Pin Operation The HOLD pin can be used to interrupt a serial operation without aborting it. If the bus master pulls the HOLD pin LOW while SCK is LOW, the current operation will pause. Taking the HOLD pin HIGH while SCK is LOW will resume an operation. The transitions of HOLD must occur while SCK is LOW, but the SCK and CS pin can toggle during a hold state. ~ ~ Figure 14. HOLD Operation [2] ~ ~ CS ~ ~ SCK ~ ~ HOLD VALID IN VALID IN ~ ~ SI SO Sleep Mode A low-power sleep mode is implemented on the FM25V02A device. The device will enter the low-power state when the SLEEP opcode B9h is clocked-in and a rising edge of CS is applied. When in sleep mode, the SCK and SI pins are ignored and SO will be HI-Z, but the device continues to monitor the CS pin. On the next falling edge of CS, the device will return to normal operation within tREC time. The SO pin remains in a HI-Z state during the wakeup period. The device does not necessarily respond to an opcode within the wakeup period. To start the wakeup procedure, the controller may send a "dummy" read, for example, and wait the remaining tREC time. Figure 15. Sleep Mode Operation Enters Sleep Mode t REC Recovers from Sleep Mode CS 0 1 2 3 4 5 6 7 t SU SCK SI 1 0 1 1 1 0 0 SO 1 VALID IN HI-Z Note 2. Figure 14 shows the HOLD operation for input mode and output mode. Document Number: 001-90865 Rev. *I Page 10 of 24 FM25V02A Device ID The FM25V02A device can be interrogated for its manufacturer, product identification, and die revision. The RDID opcode 9Fh allows the user to read the manufacturer ID and product ID, both of which are read-only bytes. The JEDEC-assigned manufacturer ID places the Cypress (Ramtron) identifier in bank 7; therefore, there are six bytes of the continuation code 7Fh followed by the single byte C2h. There are two bytes of product ID, which includes a family code, a density code, a sub code, and the product revision code. Table 6. Device ID Device ID Description 71-16 (56 bits) Device ID (9 bytes) Manufacturer ID 7F7F7F7F7F7FC22208h 0111111101111111011111110111 1111011111110111111111000010 15-13 (3 bits) 12-8 (5 bits) 7-6 (2 bits) 5-3 (3 bits) 2-0 (3 bits) Product ID Family Density Sub Rev Rsvd 001 00010 00 001 000 Figure 16. Read Device ID 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 SCK ~ ~ CS 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 Opcode SO 1 0 0 1 1 1 1 1 HI-Z D7 D6 D5 D4 D3 D2 D1 D0 ~ ~ SI D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 MSB LSB 9-Byte Device ID Document Number: 001-90865 Rev. *I Page 11 of 24 FM25V02A Endurance The FM25V02A devices are capable of being accessed at least 1014 times, reads or writes. An F-RAM memory operates with a read and restore mechanism. Therefore, an endurance cycle is applied on a row basis for each access (read or write) to the memory array. The F-RAM architecture is based on an array of rows and columns of 4K rows of 64-bits each. The entire row is internally accessed once whether a single byte or all eight bytes are read or written. Each byte in the row is counted only once in an endurance calculation. Table 7 shows endurance calculations for a 64-byte repeating loop, which includes an opcode, a starting address, and a sequential 64-byte data stream. This causes each byte to experience one endurance cycle through the loop. Document Number: 001-90865 Rev. *I Table 7. Time to Reach Endurance Limit for Repeating 64-byte Loop SCK Freq (MHz) Endurance Cycles/sec Endurance Cycles/year Years to Reach Limit 40 74,620 2.35 x 1012 42.6 37,310 1012 85.1 20 10 5 18,660 9,330 1.18 x 5.88 x 10 11 170.2 2.94 x 10 11 340.3 Page 12 of 24 FM25V02A Maximum Ratings Exceeding maximum ratings may shorten the useful life of the device. These user guidelines are not tested. Storage temperature ............................... -65 C to + 125 C Maximum accumulated storage time At 125 C ambient temperature ................................. 1000 h At 85 C ambient temperature ................................ 10 Years Ambient temperature with power applied ................................... -55 C to +125 C Supply voltage on VDD relative to VSS ........-1.0 V to + 4.5 V Input voltage ........... -1.0 V to +4.5 V and VIN < VDD + 1.0 V DC voltage applied to outputs in HI-Z state ........................................ -0.5 V to VDD + 0.5 V Package power dissipation capability (TA = 25 C) ................................................................. 1.0 W Surface mount lead soldering temperature (3 seconds) ............................................................. + 260 C DC output current (1 output at a time, 1s duration) .................................. 15 mA Electrostatic discharge voltage Human Body Model (JEDEC Std JESD22-A114-B) ................ 2 kV Charged Device Model (JEDEC Std JESD22-C101-A) .......... 500 V Latch-up current .................................................... > 140 mA Operating Range Range Industrial Ambient Temperature (TA) VDD -40 C to +85 C 2.0 V to 3.6 V Transient voltage (< 20 ns) on any pin to ground potential ............ -2.0 V to VDD + 2.0 V DC Electrical Characteristics Over the Operating Range Parameter Description VDD Power supply IDD VDD supply current Test Conditions SCK toggling between fSCK = 40 MHz VDD - 0.2 V and VSS, f SCK = 1 MHz other inputs VSS or VDD - 0.2 V. SO = Open. Min Typ[3] Max Unit 2.0 3.3 3.6 V - - 2.5 mA - - 0.22 mA - 90 150 A ISB VDD standby current CS = VDD. All other inputs VSS or VDD. IZZ Sleep mode current CS = VDD. All other inputs VSS or VDD. - 5 8 A ILI Input leakage current (Except HOLD) VSS < VIN < VDD -1 - +1 A -100 - +1 A -1 - +1 A Input leakage current (for HOLD) ILO Output leakage current VSS < VOUT < VDD VIH Input HIGH voltage 0.7 x VDD - VDD + 0.3 V VIL Input LOW voltage -0.3 - 0.3 x VDD V VOH1 Output HIGH voltage IOH = -1 mA, VDD = 2.7 V. VOH2 Output HIGH voltage IOH = -100 A VOL1 Output LOW voltage VOL2 Output LOW voltage Rin [4] Input resistance (HOLD) 2.4 - - V VDD - 0.2 - - V IOL = 2 mA, VDD = 2.7 V - - 0.4 V IOL = 150 A - - 0.2 V For VIN = VIL (max) 800 - - k For VIN = VIH (min) 30 - - k Notes 3. Typical values are at 25 C, VDD = VDD (typ). Not 100% tested. 4. The input pull-up circuit is strong (30 k) when the input voltage is above VIH and weak (800 k) when the input voltage is below VIL. Document Number: 001-90865 Rev. *I Page 13 of 24 FM25V02A Data Retention and Endurance Parameter TDR NVC Description Data retention Endurance Min Max Unit TA = 85 C Test condition 10 - Years TA = 75 C 38 - TA = 65 C 151 - 14 - Over operating temperature 10 Cycles Capacitance Parameter [5] Description CO Output pin capacitance (SO) CI Input pin capacitance Test Conditions TA = 25 C, f = 1 MHz, VDD = VDD(typ) Max Unit 8 pF 6 pF Thermal Resistance Parameter [5] Description JA Thermal resistance (junction to ambient) JC Thermal resistance (junction to case) Test Conditions 8-pin SOIC 8-pin DFN Unit Test conditions follow standard test methods and procedures for measuring thermal impedance, per EIA/JESD51. 146 31 C/W 48 35 C/W AC Test Conditions Input pulse levels .................................10% and 90% of VDD Input rise and fall times ...................................................3 ns Input and output timing reference levels ................0.5 x VDD Output load capacitance .............................................. 30 pF Note 5. This parameter is periodically sampled and not 100% tested. Document Number: 001-90865 Rev. *I Page 14 of 24 FM25V02A AC Switching Characteristics Over the Operating Range Parameters [6] Cypress Parameter Description Alt. Parameter VDD = 2.0 V to 3.6 V VDD = 2.7 V to 3.6 V Min Max Min Max Unit fSCK - SCK clock frequency 0 25 0 40 MHz tCH - Clock HIGH time 18 - 11 - ns tCL - Clock LOW time 18 - 11 - ns tCSU tCSS Chip select setup 12 - 10 - ns tCSH tCSH Chip select hold 12 - 10 - ns tOD [7, 8] tHZCS Output disable time - 20 - 12 ns tODV tCO Output data valid time - 16 - 9 ns tOH - Output hold time 0 - 0 - ns tD - Deselect time 60 - 40 - ns [9, 10] - Data in rise time - 50 - 50 ns tF[9, 10] - Data in fall time - 50 - 50 ns tSU tSD Data setup time 8 - 5 - ns tH tHD Data hold time 8 - 5 - ns tHS tSH HOLD setup time 12 - 10 - ns tHH tHH HOLD hold time 12 - 10 - ns tHZ[7, 8] tLZ[8] tHHZ HOLD LOW to HI-Z - 25 - 20 ns tHLZ HOLD HIGH to data active - 25 - 20 ns tR Notes 6. Test conditions assume a signal transition time of 3 ns or less, timing reference levels of 0.5 x VDD, input pulse levels of 10% to 90% of VDD, output loading of the specified IOL/IOH and 30 pF load capacitance shown in AC Test Conditions. 7. tOD and tHZ are specified with a load capacitance of 5 pF. Transition is measured when the outputs enter a high impedance state. 8. Characterized but not 100% tested in production. 9. Rise and fall times measured between 10% and 90% of waveform. 10. These parameters are guaranteed by design and are not tested. Document Number: 001-90865 Rev. *I Page 15 of 24 FM25V02A Figure 17. Synchronous Data Timing (Mode 0) tD CS tCSU tCH tCL tCSH SCK tSU SI tH VALID IN VALID IN VALID IN tOH tODV SO HI-Z tOD HI-Z CS SCK tHH ~ ~ ~ ~ Figure 18. HOLD Timing tHS ~ ~ tHS VALID IN tHZ Document Number: 001-90865 Rev. *I VALID IN tLZ ~ ~ SO tSU ~ ~ HOLD SI tHH Page 16 of 24 FM25V02A Power Cycle Timing Over the Operating Range Parameter Description Min Max Unit 250 - s tPU Power-up VDD (min) to first access (CS LOW) tPD Last access (CS HIGH) to power-down (VDD(min)) 0 - s tVR [11, 12] VDD power-up ramp rate 50 - s/V tVF [11, 12] VDD power-down ramp rate 100 - s/V tREC [13] Recovery time from sleep mode - 400 s VDD ~ ~ Figure 19. Power Cycle Timing VDD(min) tVR CS tVF tPD ~ ~ tPU VDD(min) Notes 11. Slope measured at any point on VDD waveform. 12. These parameters are guaranteed by design and are not tested. 13. Refer to Figure 15 on page 10 for sleep mode recovery timing. Document Number: 001-90865 Rev. *I Page 17 of 24 FM25V02A Ordering Information Package Diagram Ordering Code Package Type FM25V02A-G 51-85066 8-pin SOIC FM25V02A-GTR 51-85066 8-pin SOIC FM25V02A-DG 001-85260 8-pin DFN FM25V02A-DGTR 001-85260 8-pin DFN Operating Range Industrial All these parts are Pb-free. Contact your local Cypress sales representative for availability of these parts. Ordering Code Definitions FM 25 V 02 A - X TR Option: Blank = Standard; TR = Tape and Reel Package Type: X = G or DG G = 8-pin SOIC; DG = 8-pin DFN Device revision: A Density: 02 = 256-Kbit Voltage: V = 2.0 V to 3.6 V SPI F-RAM Cypress Document Number: 001-90865 Rev. *I Page 18 of 24 FM25V02A Package Diagrams Figure 20. 8-pin SOIC (150 Mils) Package Outline, 51-85066 51-85066 *I Document Number: 001-90865 Rev. *I Page 19 of 24 FM25V02A Package Diagrams (continued) Figure 21. 8-pin DFN (4.0 mm x 4.5 mm x 0.8 mm) Package Outline, 001-85260 001-85260 *B Document Number: 001-90865 Rev. *I Page 20 of 24 FM25V02A Acronyms Acronym Document Conventions Description Units of Measure CPHA Clock Phase CPOL Clock Polarity C degree Celsius DFN Dual Flat No-lead Hz hertz EEPROM Electrically Erasable Programmable Read-Only Memory kHz kilohertz k kilohm Kbit Kilobit MHz megahertz A microampere F microfarad s microsecond mA milliampere ms millisecond ns nanosecond ohm % percent pF picofarad V volt W watt EIA Electronic Industries Alliance F-RAM Ferroelectric Random Access Memory I/O Input/Output JEDEC Joint Electron Devices Engineering Council JESD JEDEC Standards LSB Least Significant Bit MSB Most Significant Bit RoHS Restriction of Hazardous Substances SPI Serial Peripheral Interface SOIC Small Outline Integrated Circuit Document Number: 001-90865 Rev. *I Symbol Unit of Measure Page 21 of 24 FM25V02A Document History Page Document Title: FM25V02A, 256-Kbit (32K x 8) Serial (SPI) F-RAM Document Number: 001-90865 Rev. ECN No. Orig. of Change Submission Date ** 4265427 GVCH 01/29/2014 New data sheet. *A 4390913 GVCH 06/20/2014 Changed status from Advance to Preliminary. Updated Pin Definitions: Updated details in "Description" column of "HOLD" pin (Added the sentence, "This pin has a weak internal pull-up (refer to the RIN spec in DC Electrical Characteristics on page 13)"). Updated Maximum Ratings: Removed "Machine Model" under "Electrostatic Discharge Voltage". Updated DC Electrical Characteristics: Added typical value for ISB and IZZ parameters. Changed minimum value of Rin parameter from 40 kto 30 kcorresponding to Test Condition "VIN = VIH(min)". Changed minimum value of Rin parameter from 1 Mto 800 kcorresponding to Test Condition "VIN = VIL(max)". Updated Note 4. Updated Thermal Resistance: Replaced TBD with values in "8-pin SOIC" and "8-pin TDFN" columns. *B 4571858 GVCH 11/18/2014 Updated Serial Peripheral Interface - SPI Bus: Updated Command Structure: Updated Table 1: Added reserved opcodes - 0xC3, 0xC2, 0x5A, 0x5B. *C 4197512 ZSK 02/10/2015 Changed status from Preliminary to Final. Replaced "TDFN" with "DFN" in all instances across the document. Updated Functional Description: Added "For a complete list of related resources, click here." at the end. Updated Pin Definitions: Updated details in "Description" column of "EXPOSED PAD" pin. Updated Package Diagrams: spec 51-85066 - Changed revision from *F to *G. *D 4784430 GVCH 06/02/2015 Updated Package Diagrams: spec 001-85260 - Changed revision from *A to *B. Updated to new template. *E 4879715 ZSK / PSR 08/11/2015 Updated Maximum Ratings: Removed "Maximum junction temperature" and its corresponding details. Added "Maximum accumulated storage time" and its corresponding details. Added "Ambient temperature with power applied" and its corresponding details. *F 5085935 GVCH 01/14/2016 Updated Ordering Information: Updated part numbers. Updated Package Diagrams: spec 51-85066 - Changed revision from *G to *H. *G 5450688 ZSK 09/27/2016 Updated Power Cycle Timing: Changed minimum value of tPU parameter from 1 ms to 250 s. Updated to new template. *H 5768943 AESATMP9 06/09/2017 Updated logo and copyright. Document Number: 001-90865 Rev. *I Description of Change Page 22 of 24 FM25V02A Document History Page (continued) Document Title: FM25V02A, 256-Kbit (32K x 8) Serial (SPI) F-RAM Document Number: 001-90865 Rev. ECN No. Orig. of Change Submission Date Description of Change *I 6404910 GVCH 12/07/2018 Updated Maximum Ratings: Replaced "-55 C to +125 C" with "-65 C to +125 C" in ratings corresponding to "Storage temperature". Updated Package Diagrams: spec 51-85066 - Changed revision from *H to *I. Updated to new template. Document Number: 001-90865 Rev. *I Page 23 of 24 FM25V02A Sales, Solutions, and Legal Information Worldwide Sales and Design Support Cypress maintains a worldwide network of offices, solution centers, manufacturer's representatives, and distributors. To find the office closest to you, visit us at Cypress Locations. PSoC(R) Solutions Products Arm(R) Cortex(R) Microcontrollers Automotive cypress.com/arm cypress.com/automotive Clocks & Buffers Interface Internet of Things Memory cypress.com/clocks cypress.com/interface cypress.com/iot cypress.com/memory Microcontrollers cypress.com/mcu PSoC cypress.com/psoc Power Management ICs Touch Sensing USB Controllers Wireless Connectivity PSoC 1 | PSoC 3 | PSoC 4 | PSoC 5LP | PSoC 6 MCU Cypress Developer Community Community | Projects | Video | Blogs | Training | Components Technical Support cypress.com/support cypress.com/pmic cypress.com/touch cypress.com/usb cypress.com/wireless (c) Cypress Semiconductor Corporation, 2014-2018. This document is the property of Cypress Semiconductor Corporation and its subsidiaries, including Spansion LLC ("Cypress"). This document, including any software or firmware included or referenced in this document ("Software"), is owned by Cypress under the intellectual property laws and treaties of the United States and other countries worldwide. Cypress reserves all rights under such laws and treaties and does not, except as specifically stated in this paragraph, grant any license under its patents, copyrights, trademarks, or other intellectual property rights. If the Software is not accompanied by a license agreement and you do not otherwise have a written agreement with Cypress governing the use of the Software, then Cypress hereby grants you a personal, non-exclusive, nontransferable license (without the right to sublicense) (1) under its copyright rights in the Software (a) for Software provided in source code form, to modify and reproduce the Software solely for use with Cypress hardware products, only internally within your organization, and (b) to distribute the Software in binary code form externally to end users (either directly or indirectly through resellers and distributors), solely for use on Cypress hardware product units, and (2) under those claims of Cypress's patents that are infringed by the Software (as provided by Cypress, unmodified) to make, use, distribute, and import the Software solely for use with Cypress hardware products. Any other use, reproduction, modification, translation, or compilation of the Software is prohibited. TO THE EXTENT PERMITTED BY APPLICABLE LAW, CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS DOCUMENT OR ANY SOFTWARE OR ACCOMPANYING HARDWARE, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. No computing device can be absolutely secure. Therefore, despite security measures implemented in Cypress hardware or software products, Cypress does not assume any liability arising out of any security breach, such as unauthorized access to or use of a Cypress product. In addition, the products described in these materials may contain design defects or errors known as errata which may cause the product to deviate from published specifications. To the extent permitted by applicable law, Cypress reserves the right to make changes to this document without further notice. Cypress does not assume any liability arising out of the application or use of any product or circuit described in this document. Any information provided in this document, including any sample design information or programming code, is provided only for reference purposes. It is the responsibility of the user of this document to properly design, program, and test the functionality and safety of any application made of this information and any resulting product. Cypress products are not designed, intended, or authorized for use as critical components in systems designed or intended for the operation of weapons, weapons systems, nuclear installations, life-support devices or systems, other medical devices or systems (including resuscitation equipment and surgical implants), pollution control or hazardous substances management, or other uses where the failure of the device or system could cause personal injury, death, or property damage ("Unintended Uses"). A critical component is any component of a device or system whose failure to perform can be reasonably expected to cause the failure of the device or system, or to affect its safety or effectiveness. Cypress is not liable, in whole or in part, and you shall and hereby do release Cypress from any claim, damage, or other liability arising from or related to all Unintended Uses of Cypress products. You shall indemnify and hold Cypress harmless from and against all claims, costs, damages, and other liabilities, including claims for personal injury or death, arising from or related to any Unintended Uses of Cypress products. Cypress, the Cypress logo, Spansion, the Spansion logo, and combinations thereof, WICED, PSoC, CapSense, EZ-USB, F-RAM, and Traveo are trademarks or registered trademarks of Cypress in the United States and other countries. For a more complete list of Cypress trademarks, visit cypress.com. Other names and brands may be claimed as property of their respective owners. Document Number: 001-90865 Rev. *I Revised December 7, 2018 Page 24 of 24