FSGM0565RWDTU - APTINA IMAGING - Datasheet.Directory

June, 2019 − Rev. 2

1Publication Order Number:

FSGM0565R/D

FSGM0565R

Green-Mode Power Switch

Description

The FSGM0565RB is an integrated Pulse Width Modulation

(PWM) controller and SENSEFET® specifically designed for offline

Switch−Mode Power Supplies (SMPS) with minimal external

components. The PWM controller includes an integrated

fixed−frequency oscillator, Under−Voltage Lockout (UVLO),

Leading−Edge Blanking (LEB), optimized gate driver, internal

soft−start, temperature−compensated precise current sources for loop

compensation, and self−protection circuitry. Compared with a discrete

MOSFET and PWM controller solution, the FSGM series can reduce

total cost, component count, size, and weight; while simultaneously

increasing efficiency, productivity, and system reliability. This device

provides a basic platform suited for cost−effective design of a flyback

converter.

Features

•Soft Burst−Mode Operation for Low Standby Power Consumption

and Low Noise

•Precision Fixed Operating Frequency: 66 kHz

•Pulse−by−Pulse Current Limit

•Various Protection Functions: Overload Protection (OLP),

Over−Voltage Protection (OVP), Abnormal Over−Current Protection

(AOCP), Internal Thermal Shutdown (TSD) with Hysteresis,

Output−Short Protection (OSP), and Under−Voltage Lockout

(UVLO) with Hysteresis

•Auto−Restart Mode

•Internal Startup Circuit

•Internal High−Voltage SENSEFET: 650 V

•Built−in Soft−Start: 15 ms

•These Devices are Pb−Free and are RoHS Compliant

Applications

•Power Supply for LCD TV and Monitor, STB and DVD

Combination

www.onsemi.com

TO−220−6LD LF

CASE 340BG

MARKING DIAGRAM

$Y = ON Semiconductor Logo

&Z = Assembly Plant Code

&3 = 3−Digit Date Code Format

&K = 2−Digit Lot Run Tracebility Code

GM0765R = Specific Device Code Data

See detailed ordering and shipping information on page 2 of

this data sheet.

ORDERING INFORMATION

$Y&Z&3&K

GM0765R

TO−220 FULLPAK 6LD LF

CASE 340BP

TO−220−6LD LF

CASE 340BN

$Y&Z&3&K

GM0765R

FSGM0565R

www.onsemi.com

ORDERING INFORMATION

Part Number Package

Operating

Junction

Temperature Current Limit

RDS(ON)

(Max.)

Output Power Table (Note 2)

Replaces

Device Shipping

230VAC  15% (Note 3) 85 − 265 VAC

Adapter

(Note 4)

Open Frame

(Note 5)

Adapter

(Note 4)

Open Frame

(Note 5)

FSGM0565RWDTU TO−220F

6−Lead

(Note 1)

W−Forming

−40°C ~

+125°C

2.20 A 2.2 W70 W 80 W 41 W 60 W FSDM0565RE 400 / Tube

FSGM0565RUDTU TO−220F

6−Lead

(Note 1)

U−Forming

−40°C ~

+125°C

2.20 A 2.2 W70 W 80 W 41 W 60 W FSDM0565RE 400 / Tube

FSGM0565RLDTU TO−220F

6−Lead

(Note 1)

L−Forming

−40°C ~

+125°C

2.20 A 2.2 W70 W 80 W 41 W 60 W FSDM0565RE 400 / Tube

1. Pb−free package per JEDEC J−STD−020B.

2. The junction temperature can limit the maximum output power.

3. 230 VAC or 100 / 115 VAC with voltage doubler.

4. Typical continuous power in a non−ventilated enclosed adapter measured at 50°C ambient temperature.

5. Maximum practical continuous power in an open−frame design at 50°C ambient temperature.

Application Circuit

Figure 1. Typical Application Circuit

PWM

VSTR

Drain

GND

FB VCC

FSGM0565R

www.onsemi.com

Internal Block Diagram

Figure 2. Internal Block Diagram

tON < tOSP (1.2 ms)

OSC

IFB

CC good

STR Drain

GND

Gate

Driver

LEB (300 ns)

PWM

IDELAY SQ

R Q

burst

0.5 V / 0.7 V

N.C.

AOCP

OSP

OVP

24.5 V

LPF

TSD

6 V

Soft Start

7.5V / 12V

CC good

Vref

CC V

ref

Soft Burst

Pin Configuration

6. V

STR

5. N.C.

4. FB

3. V

2. GND

1. Drain

Figure 3. Pin Configuration (Top View)

FSGM0565R

www.onsemi.com

PIN DEFINITIONS

Pin No. Name Description

ÁÁÁÁ

ÁÁÁ

Drain

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

SENSEFET Drain. High−voltage power SENSEFET drain connection.

ÁÁÁÁ

ÁÁÁ

GND

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Ground. This pin is the control ground and the SENSEFET source.

ÁÁÁÁ

ÁÁÁ

VCC

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Power Supply. This pin is the positive supply input, which provides the internal operating current for both startup and

steady−state operation.

ÁÁÁÁ

ÁÁÁ

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Feedback. This pin is internally connected to the inverting input of the PWM comparator. The collector of an

opto−coupler is typically tied to this pin. For stable operation, a capacitor should be placed between this pin and

GND. If the voltage of this pin reaches 6 V, the overload protection triggers, which shuts down the power switch.

ÁÁÁÁ

ÁÁÁ

N.C.

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

No connection.

ÁÁÁÁ

ÁÁÁ

VSTR

ÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁÁ

Startup. This pin is connected directly, or through a resistor, to the high−voltage DC link. At startup, the internal

high−voltage current source supplies internal bias and charges the external capacitor connected to the VCC pin.

Once VCC reaches 12 V, the internal current source (ICH) is disabled.

ABSOLUTE MAXIMUM RATINGS

Symbol Parameter Min Max Unit

VSTR VSTR Pin Voltage −650 V

VDS Drain Pin Voltage −650 V

VCC VCC Pin Voltage −26 V

VFB Feedback Pin Voltage −0.3 12 V

IDM Drain Current Pulsed −11 A

IDS Continuous Switching Drain Current (Note 6) TC = 25°C−5.6 A

TC = 100°C−3.4 A

EAS Single Pulsed Avalanche Energy (Note 7) −295 mJ

PDTotal Power Dissipation (TC = 25°C) (Note 8) −45 W

TJMaximum Junction Temperature −150 °C

Operating Junction Temperature (Note 9) −40 +125 °C

TSTG Storage Temperature −55 +150 °C

VISO Minimum Isolation Range (Note 10) 2.5 −V

ESD Electrostatic Discharge Capability Human Body Model, JESD22−A114 2−kV

Charged Device Model, JESD22−C101 2−

Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality

should not be assumed, damage may occur and reliability may be affected.

6. Repetitive peak switching current when the inductive load is assumed: Limited by maximum duty (DMAX = 0.75) and junction temperature

(see Figure 4).

7. L = 45mH, starting TJ = 25°C.

8. Infinite cooling condition (refer to the SEMI G30−88).

9. Although this parameter guarantees IC operation, it does not guarantee all electrical characteristics.

10.The voltage between the package back side and the lead is guaranteed.

IDS

DMAX

Figure 4. Repetitive Peak Switching Current

FSGM0565R

www.onsemi.com

THERMAL IMPEDANCE TA = 25°C unless otherwise specified.

Symbol Characteristic Value Unit

qJA Junction−to−Ambient Thermal Impedance (Note 11) 62.5 °C/W

qJC Junction−to−Case Thermal Impedance (Note 12) 3°C/W

11. Infinite cooling condition (refer to the SEMI G30−88).

12.Free standing with no heat−sink under natural convection.

ELECTRICAL CHARACTERISTICS (TJ = 25°C unless otherwise noted)

Symbol Parameter Test Condition Min Typ Max Unit

SENSEFET SECTION

BVDSS Drain−Source Breakdown Voltage VCC = 0 V, ID = 250 mA650 − − V

IDSS Zero−Gate−Voltage Drain Current VDS = 520 V, TA = 125°C− − 250 mA

RDS(ON) Drain−Source On−State Resistance VGS = 10 V, ID = 1 A −1.8 2.2 W

CISS Input Capacitance (Note 13) VDS = 25 V, VGS = 0 V, f = 1MHz −515 −pF

COSS Output Capacitance (Note 13) VDS = 25 V, VGS = 0 V, f = 1MHz −75 −pF

tr Rise Time VDS = 325 V, ID = 4 A, RG = 25 W−26 −ns

tf Fall Time VDS = 325 V, ID = 4 A, RG = 25 W−25 −ns

td(on) Turn−on Delay Time VDS = 325 V, ID = 4 A, RG = 25 W−14 −ns

td(off) Turn−off Delay Time VDS = 325 V, ID = 4 A, RG = 25 W−32 −ns

CONTROL SECTION

fS Switching Frequency VCC = 14 V, VFB = 4 V 60 66 72 kHz

DfS Switching Frequency Variation (Note 13) −25°C < TJ < +125°C−±5±10 %

DMAX Maximum Duty Ratio VCC = 14 V, VFB = 4 V 65 70 75 %

DMIN Minimum Duty Ratio VCC = 14 V, VFB = 0 V − − 0 %

IFB Feedback Source Current VFB = 0 160 210 260 mA

VSTART UVLO Threshold Voltage VFB = 0 V, VCC Sweep 11 12 13 V

VSTOP After Turn−on, VFB = 0 V 7.0 7.5 8.0 V

VOP VCC Operating Range 13 −23 V

tS/S Internal Soft−Start Time VSTR = 40 V, VCC Sweep −15 −ms

BURST−MODE SECTION

VBURH Burst−Mode Voltage VCC = 14 V, VFB Sweep 0.6 0.7 0.8 V

VBURL 0.4 0.5 0.6 V

Hys −200 −mV

PROTECTION SECTION

ILIM Peak Drain Current Limit di/dt = 300 mA/ms2.0 2.2 2.4 A

VSD Shutdown Feedback Voltage VCC = 14 V, VFB Sweep 5.5 6.0 6.5 V

IDELAY Shutdown Delay Current VCC = 14 V, VFB = 4 V 2.5 3.3 4.1 mA

Hys Leading−Edge Blanking Time (Note 13, 14) −300 −ns

VOVP Over−Voltage Protection VCC Sweep 23.0 24.5 26.0 V

FSGM0565R

www.onsemi.com

ELECTRICAL CHARACTERISTICS (TJ = 25°C unless otherwise noted) (continued)

Symbol UnitMaxTypMinTest ConditionParameter

PROTECTION SECTION

tOSP Output Short

Protection (Note 13)

Threshold Time OSP Triggered when tON < tOSP &

VFB > VOSP (Lasts Longer than

tOSP_FB)

1.0 1.2 1.4 ms

VOSP Threshold VFB 1.8 2.0 2.2 V

tOSP_FB VFB Blanking Time 2.0 2.5 3.0 ms

TSD Thermal Shutdown Temperature (Note 13) Shutdown Temperature 130 140 150 °C

Hys Hysteresis −30 −°C

TOTAL DEVICE SECTION

IOP Operating Supply Current, (Control Part in

Burst Mode)

VCC = 14 V, VFB = 0 V 1.2 1.6 2.0 mA

IOPS Operating Switching Current, (Control Part

and SENSEFET Part)

VCC = 14 V, VFB = 4 V 2.0 2.5 3.0 mA

ISTART Start Current VCC = 11 V (Before VCC Reaches

VSTART)

0.5 0.6 0.7 mA

ICH Startup Charging Current VCC = VFB = 0 V, VSTR = 40 V 1.00 1.15 1.50 mA

VSTR Minimum VSTR Supply Voltage VCC = VFB = 0 V, VSTR Sweep −26 −V

Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product

performance may not be indicated by the Electrical Characteristics if operated under different conditions.

13.Although these parameters are guaranteed, they are not 100% tested in production.

14.tLEB includes gate turn−on time.

COMPARISON OF FSDM0565RE AND FSGM0565R

Function FSDM0565RE FSGM0565R Advantages of FSGM0565R

Burst Mode Advanced Burst Advanced Soft Burst Low noise and low standby power

Lightning Surge Strong Enhanced SENSEFET and controller against lightning surge

Soft−Start 10 ms (Built−in) 15 ms (Built−in) Longer soft−start time

Protections OLP

OVP

TSD

OLP

OVP

OSP

AOCP

TSD with Hysteresis

Enhanced protections and high reliability

Power Balance Long TCLD Very Short TCLD The difference of input power between the low and high input

voltage is quite small

FSGM0565R

www.onsemi.com

TYPICAL CHARACTERISTICS (Characteristic graphs are normalized at TA = 25°C)

−40°C−25°C0°C25°C50°C75°C 100°C 125°C−40°C−25°C0°C25°C50°C75°C 100°C 125°C

−40°C−25°C0°C25°C50°C75°C 100°C 125°C

0.80

0.85

0.90

0.95

1.00

1.05

1.10

1.15

1.20

−40°C−25°C0°C25°C50°C75°C 100°C 125°C

Normalized

0.80

0.85

0.90

0.95

1.00

1.05

1.10

1.15

1.20

Normalized

0.60

0.70

0.80

0.90

1.00

1.10

1.20

1.30

1.40

Normalized

0.80

0.85

0.90

0.95

1.00

1.05

1.10

1.15

1.20

Normalized

0.80

0.85

0.90

0.95

1.00

1.05

1.10

1.15

1.20

Normalized

0.80

0.85

0.90

0.95

1.00

1.05

1.10

1.15

1.20

Normalized

Temperature [°C] Temperature [°C]

Figure 5. Operating Supply Current (IOP) vs. TAFigure 6. Operating Switching Current (IOPS) vs. TA

Figure 7. Startup Charging Current (ICH) vs. TAFigure 8. Peak Drain Current Limit (ILIM) vs. TA

Figure 9. Feedback Source Current (IFB) vs. TAFigure 10. Shutdown Delay Current (IDELAY) vs. TA

FSGM0565R

www.onsemi.com

TYPICAL CHARACTERISTICS (Characteristic graphs are normalized at TA = 25°C)

−40°C−25°C0°C25°C50°C75°C 100°C 125°C−40°C−25°C0°C25°C50°C75°C 100°C 125°C

Normalized

Temperature [°C] Temperature [°C]

0.80

0.85

0.90

0.95

1.00

1.05

1.10

1.15

1.20

0.80

0.85

0.90

0.95

1.00

1.05

1.10

1.15

1.20

0.80

0.85

0.90

0.95

1.00

1.05

1.10

1.15

1.20

0.80

0.85

0.90

0.95

1.00

1.05

1.10

1.15

1.20

0.80

0.85

0.90

0.95

1.00

1.05

1.10

1.15

1.20

0.80

0.85

0.90

0.95

1.00

1.05

1.10

1.15

1.20

Figure 11. UVLO Threshold Voltage (VSTART) vs. TAFigure 12. UVLO Threshold Voltage (VSTOP) vs. TA

Figure 13. Shutdown Feedback Voltage (VSD) vs. TAFigure 14. Over−Voltage Protection (VOVP) vs. TA

Figure 15. Switching Frequency (fS) vs. TAFigure 16. Maximum Duty Ratio (DMAX) vs. TA

FSGM0565R

www.onsemi.com

FUNCTIONAL DESCRIPTION

Startup

At startup, an internal high−voltage current source

supplies the internal bias and charges the external capacitor

(CVcc) connected to the VCC pin, as illustrated in Figure 17.

When VCC reaches 12 V, the FSGM0465R begins switching

and the internal high− voltage current source is disabled. The

FSGM0465R continues normal switching operation and the

power is supplied from the auxiliary transformer winding

unless VCC goes below the stop voltage of 7.5 V.

7.5 V / 12 V

Vref

Internal

Bias

VCC VSTR

ICH

VCC good

VDC

CVcc

3 6

Figure 17. Startup Block

Soft−Start

The FSGM0465R has an internal soft−start circuit that

increases PWM comparator inverting input voltage,

together with the SENSEFET current, slowly after it starts.

The typical soft−start time is 15 ms. The pulse width to the

power switching device is progressively increased to

establish the correct working conditions for transformers,

inductors, and capacitors. The voltage on the output

capacitors is progressively increased to smoothly establish

the required output voltage. This helps prevent transformer

saturation and reduces stress on the secondary diode during

startup.

Feedback Control

This device employs current−mode control, as shown in

Figure 18. An opto−coupler (such as the FOD817) and shunt

regulator (such as the KA431) are typically used to

implement the feedback network. Comparing the feedback

voltage with the voltage across the RSENSE resistor makes it

possible to control the switching duty cycle. When the

reference pin voltage of the shunt regulator exceeds the

internal reference voltage of 2.5 V, the opto−coupler LED

current increases, pulling down the feedback voltage and

reducing drain current. This typically occurs when the input

voltage increases or the output load is decreases.

Pulse−by−Pulse Current Limit

Because current− mode control is employed, the peak

current through the SENSEFET is limited by the inverting

input of PWM comparator (VFB*), as shown in Figure 18.

Assuming that the 210 mA current source flows only through

the internal resistor (3R + R = 11.6 kW), the cathode voltage

of diode D2 is about 2.4 V. Since D1 is blocked when the

feedback voltage (VFB) exceeds 2.4 V, the maximum

voltage of the cathode of D2 is clamped at this voltage.

Therefore, the peak value of the current through the

SENSEFET is limited.

Leading−Edge Blanking (LEB)

At the instant the internal SENSEFET is turned on, a

high−current spike usually occurs through the SENSEFET,

caused by primary−side capacitance and secondary−side

rectifier reverse recovery. Excessive voltage across the

RSENSE resistor leads to incorrect feedback operation in

the current mode PWM control. To counter this effect, the

FSGM0565RB employs a leading−edge blanking (LEB)

circuit. This circuit inhibits the PWM comparator for tLEB

(300 ns) after the SENSEFET is turned on.

Figure 18. Pulse Width Modulation Circuit

OSC

IFB

Drain

GND

Gate

Driver

PWM

IDELAY

AOCP

VOSP

VSD

VCC Vref

OLP

OSP

AOCP

KA431

CFB

FOD817

VFB

VOUT

RSENSE

VFB

LEB (300 ns)

D1 D2

FSGM0565R

www.onsemi.com

Protection Circuits

The FSGM0565RB has several self−protective functions,

such as Overload Protection (OLP), Abnormal

Over−Current Protection (AOCP), Output−Short Protection

(OSP), Over−Voltage Protection (OVP), and Thermal

Shutdown (TSD). All the protections are implemented as

auto−restart. Once the fault condition is detected, switching

is terminated and the SENSEFET remains off. This causes

VCC to fall. When VBCC falls to the Under−Voltage Lockout

(UVLO) stop voltage of 7.5 V, the protection is reset and the

startup circuit charges the VCC capacitor. When VCC reaches

the start voltage of 12.0 V, the FSGM0565RB resumes

normal operation. If the fault condition is not removed, the

SENSEFET remains off and VCC drops to stop voltage

again. In this manner, the auto−restart can alternately enable

and disable the switching of the power SENSEFET until the

fault condition is eliminated. Because these protection

circuits are fully integrated into the IC without external

components, the reliability is improved without increasing

cost.

Fault

situation

7.5 V

12.0 V

VCC

VDS

Fault

occurs

Fault

removed

Normal

operation

Normal

operation

Power

Figure 19. Auto−Restart Protection Waveforms

Overload Protection (OLP)

Overload is defined as the load current exceeding its

normal level due to an unexpected abnormal event. In this

situation, the protection circuit should trigger to protect the

SMPS. However, even when the SMPS is in normal

operation, the overload protection circuit can be triggered

during the load transition. To avoid this undesired operation,

the overload protection circuit is designed to trigger only

after a specified time to determine whether it is a transient

situation or a true overload situation. Because of the

pulse−by−pulse current limit capability, the maximum peak

current through the SENSEFET is limited and, therefore, the

maximum input power is restricted with a given input

voltage. If the output consumes more than this maximum

power, the output voltage (VOUT) decreases below the set

voltage. This reduces the current through the opto−coupler

LED, which also reduces the opto−coupler transistor

current, thus increasing the feedback voltage (VFB). If VFB

exceeds 2.4 V, D1 is blocked and the 3.3 mA current source

starts to charge CFB slowly up. In this condition, VFB

continues increasing until it reaches 6.0 V, when the

switching operation is terminated, as shown in Figure 20.

The delay time for shutdown is the time required to charge

CFB from 2.4 V to 6.0 V with 3.3 mA. A 25 ~ 50 ms delay is

typical for most applications. This protection is

implemented in auto−restart mode.

VFB

2.4 V

6.0 V

Overload Protection

t1t

Figure 20. Overload Protection

t12 = CFB x (6.0 − 2.4) / Idelay

Abnormal Over−Current Protection (AOCP)

When the secondary rectifier diodes or the transformer

pins are shorted, a steep current with extremely high di/dt

can flow through the SENSEFET during the minimum

turn−on time. Even though the FSGM0565RB has overload

protection, it is not enough to protect the FSGM0565RB in

that abnormal case; since severe current stress is imposed on

the SENSEFET until OLP is triggered. The FSGM0565RB

internal AOCP circuit is shown in Figure 21. When the gate

turn−on signal is applied to the power SENSEFET, the

AOCP block is enabled and monitors the current through the

sensing resistor. The voltage across the resistor is compared

with a preset AOCP level. If the sensing resistor voltage is

greater than the AOCP level, the set signal is applied to the

S−R latch, resulting in the shutdown of the SMPS.

OSC

Drain

GND

PWM

VAOCP

RSENSE

FB*

VCC good

Gate

Driver

Figure 21. Abnormal Over−Current Protection

LEB (300 ns)

FSGM0565R

www.onsemi.com

Output−Short Protection (OSP)

If the output is shorted, steep current with extremely high

di/dt can flow through the SENSEFET during the minimum

turn−on time. Such a steep current brings high−voltage

stress on the drain of the SENSEFET when turned off. To

protect the device from this abnormal condition, OSP is

included. It is comprised of detecting VFB and SENSEFET

turn−on time. When the VFB is higher than 2 V and the

SENSEFET turn−on time is lower than 1.2 ms, the

FSGM0565RB recognizes this condition as an abnormal

error and shuts down PWM switching until VCC reaches

VSTART again. An abnormal condition output short is shown

in Figure 22.

MOSFET

Drain

Current

Rectifier

Diode

Current

VOUT

output short occurs

IOUT

tON

VFB

OSP

OSP triggered

ILm

tOFF

ILIM

VFB* = 0.5 V

 VFB* = 2.0 V

1.2 ms 1.2 ms

Figure 22. Output−Short Protection

Over−Voltage Protection (OVP)

If the secondary−side feedback circuit malfunctions or a

solder defect causes an opening in the feedback path, the

current through the opto−coupler transistor becomes almost

zero. Then VFB climbs up in a similar manner to the overload

situation, forcing the preset maximum current to be supplied

to the SMPS until the overload protection is triggered.

Because more energy than required is provided to the output,

the output voltage may exceed the rated voltage before the

overload protection is triggered, resulting in the breakdown

of the devices in the secondary side. To prevent this

situation, an OVP circuit is employed. In general, the VCC

is proportional to the output voltage and the FSGM0565RB

uses VCC instead of directly monitoring the output voltage.

If VCC exceeds 24.5 V, an OVP circuit is triggered, resulting

in the termination of the switching operation. To avoid

undesired activation of OVP during normal operation, VCC

should be designed to be below 24.5 V.

Thermal Shutdown (TSD)

The SENSEFET and the control IC on a die in one

package makes it easier for the control IC to detect the over

temperature of the SENSEFET. If the temperature exceeds

~140°C, the thermal shutdown is triggered and the

FSGM0465R stops operation. The FSGM0465R operates in

auto−restart mode until the temperature decreases to around

110°C, when normal operation resumes.

Soft Burst−Mode Operation

To minimize power dissipation in standby mode, the

FSGM0465R enters burst−mode operation. As the load

decreases, the feedback voltage decreases. As shown in

Figure 23, the device automatically enters burst mode when

the feedback voltage drops below VBURL (500 mV). At this

point, switching stops and the output voltages start to drop

at a rate dependent on standby current load. This causes the

feedback voltage to rise. Once it passes VBURH (700 mV),

switching resumes. At this point, the drain current peak

increases gradually. This soft burst−mode can reduce

audible noise during burst−mode operation. The feedback

voltage then falls and the process repeats. Burst−mode

operation alternately enables and disables switching of the

SENSEFET, thereby reducing switching loss in standby

mode.

VFB

VDS

0.50 V

0.70 V

IDS

Switching

disabled

t1 t2 t3

Switching

disabled t4

Soft Burst

Figure 23. Burst−Mode Operation

FSGM0565R

www.onsemi.com

TYPICAL APPLICATION CIRCUIT

Application Input Voltage Rated Output Rated Power

LCD TV, Monitor Power Supply 85 ∼ 265VAC 5.0 V (2 A)

14.0 V (2.8 A)

49.2 W

Key Design Notes:

1. The delay time for overload protection is designed

to be about 40 ms with C105 (33 nF). OLP time

between 25 ms (22 nF) and 50 ms (43 nF) is

recommended.

2. The SMD−type capacitor (C106) must be placed

as close as possible to the VCC pin to avoid

malfunction by abrupt pulsating noises and to

improve ESD and surge immunity. Capacitance

between 100 nF and 220 nF is recommended.

Schematic

C102

150nF

275VAC

LF101

20mH

C101

220nF

275VAC

NTC101

5D−9

F101

FUSE

250V

3.15A

C103

100μF

400V

R103

Ω51k

C104

3.3nF

630V

D101

1N 4007

C105

33nF

100V

T101

EER3016

BD101

G2SBA60

R101

Ω1.5M

FSGM0465R

VSTR

FB VCC

Drain

GND

D201

MBR20150CT

C201

1000μF

25V

C202

1000μF

25V

L201

5μH

14V, 2.8A

7, 8

D202

FYPF2006DN

C203

2200μF

10V

C204

1000μF

16V

L202

5μH

5V, 2A

R201

Ω620

R202

Ω1.2k

R204

Ω8k

R203

Ω18k

C205

68nF

R205

C301

4.7nF

IC301

FOD817B IC201

KA431LZ

R102

75k

C107

47μF

50V

D102

UF 4004

C106

220nF

SMD

N.C.5

R104

Ω51

0.5W

ZD101

1N4749A

C206

100nF

SMD

C207

100nF

SMD

Figure 24. Schematic of Demonstration Board

Transformer

EER3019

N14V

Np/2

N5V

Np/2

Figure 25. Schematic of Transformer

BOT TOP

FSGM0565R

www.onsemi.com

WINDING SPECIFICATION

Pin (S  F) Wire Turns Winding Method

Barrier Tape

TOP BOT Ts

Np/2 3 → 2 0.35 φ x 1 22 Solenoid Winding 2.0 mm 1