Analog/HDMI Dual-Display Interface AD9380 FEATURES Advanced TVs HDTV Projectors LCD monitor GENERAL DESCRIPTION The AD9380 offers designers the flexibility of an analog interface and high definition multimedia interface (HDMI) receiver integrated on a single chip. Also included is support for high bandwidth digital content protection (HDCP). The AD9380 is a complete 8-bit, 150 MSPS, monolithic analog interface optimized for capturing component video (YPbPr) and RGB graphics signals. Its 150 MSPS encode rate capability and full power analog bandwidth of 330 MHz supports all HDTV formats (up to 1080p and FPD resolutions up to SXGA (1280 x 1024 @ 75 Hz). The analog interface includes a 150 MHz triple ADC with internal 1.25 V reference, a phase-locked loop (PLL), and programmable gain, offset, and clamp control. The user provides only 1.8 V and 3.3 V power supplies, analog input, and HSYNC . Three-state CMOS outputs can be powered from 1.8 V to 3.3 V. An on-chip PLL generates a pixel clock from HSYNC. ANALOG INTERFACE 2:1 MUX HSYNC 0 HSYNC 1 HSYNC 0 HSYNC 1 2:1 MUX SOGIN 0 SOGIN 1 2:1 MUX COAST FILT CKINV CKEXT SCL SDA 2:1 MUX R/G/B 8 x 3 A/D CLAMP SYNC PROCESSING AND CLOCK GENERATION OR YCbCr 2 DATACK HSOUT VSOUT SOGOUT REFOUT REFIN REF SERIAL REGISTER AND POWER MANAGEMENT YCbCr MATRIX R/G/B OR YPbPrIN1 RGB R/G/B OR YPbPrIN0 YCbCr (4:2:2 OR 4:4:4) 2 DATACK HSOUT VSOUT SOGOUT DE DIGITAL INTERFACE R/G/B 8 x 3 OR YCbCr Rx0+ Rx0- Rx1+ Rx1- Rx2+ Rx2- RxC+ RxC- R/G/B 8 x 3 2 HDMI RECEIVER DATACK DE HSYNC VSYNC S/PDIF 4 8-CHANNEL I2S RTERM SCLK MCLK LRCLK DDCSDA DDCSCL HDCP HDCP KEYS AD9380 Figure 1. Pixel clock output frequencies range from 12 MHz to 150 MHz. PLL clock jitter is typically less than 700 ps p-p at 150 MHz. The AD9380 also offers full sync processing for composite sync and sync-on-green (SOG) applications. The AD9380 contains an HDMI 1.1-compatible receiver and supports all HDTV formats (up to 1080p and 720p) and display resolutions up to SXGA (1280 x 1024 @ 75 Hz). The receiver features an intrapair skew tolerance of up to one full clock cycle. With the inclusion of HDCP, displays can now receive encrypted video content. The AD9380 allows for authentication of a video receiver, decryption of encoded data at the receiver, and renewability of the authentication during transmission, as specified by the HDCP 1.1 protocol. Fabricated in an advanced CMOS process, the AD9380 is provided in a space-saving, 100-lead, surface-mount, Pb-free plastic LQFP and is specified over the 0C to 70C temperature range. Rev. 0 Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. 05688-001 APPLICATIONS FUNCTIONAL BLOCK DIAGRAM MUXES Internal key storage for HDCP Analog/HDMI dual interface Supports high bandwidth digital content protection RGB-to-YCbCr 2-way color conversion Automated clamping level adjustment 1.8 V/3.3 V power supply 100-lead, Pb-free LQFP RGB and YCbCr output formats Analog interface 8-bit triple ADC 100 MSPS maximum conversion rate Macrovision(R) detection 2:1 input mux Full sync processing Sync detect for hot plugging Midscale clamping Digital video interface HDMI 1.1, DVI 1.0 150 MHz HDMI receiver Supports HDCP 1.1 Digital audio interface HDMI 1.1-compatible audio interface S/PDIF (IEC90658-compatible) digital audio output Multichannel I2S audio output (up to 8 channels) One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 (c) 2005 Analog Devices, Inc. All rights reserved. AD9380 TABLE OF CONTENTS Features .............................................................................................. 1 2-Wire Serial Register Map ........................................................... 23 Applications....................................................................................... 1 2-Wire Serial Control Register DetailS........................................ 37 Functional Block Diagram .............................................................. 1 Chip Identification ..................................................................... 37 General Description ......................................................................... 1 PLL Divider Control .................................................................. 37 Specifications..................................................................................... 3 Clock Generator Control .......................................................... 37 Analog Interface Electrical Characteristics............................... 3 Input Gain ................................................................................... 38 Digital Interface Electrical Characteristics ............................... 4 Input Offset ................................................................................. 38 Absolute Maximum Ratings............................................................ 6 Sync .............................................................................................. 39 Explanation of Test Levels ........................................................... 6 Coast and Clamp Controls........................................................ 39 ESD Caution.................................................................................. 6 Status of Detected Signals ......................................................... 39 Pin Configuration and Function Descriptions............................. 7 Polarity Status ............................................................................. 40 Design Guide................................................................................... 12 BT656 Generation ...................................................................... 44 General Description................................................................... 12 Macrovision................................................................................. 45 Digital Inputs .............................................................................. 12 Color Space Conversion ............................................................ 46 Analog Input Signal Handling.................................................. 12 2-Wire Serial Control Port ............................................................ 53 HSYNC and VSYNC Inputs...................................................... 12 Data Transfer via Serial Interface............................................. 53 Serial Control Port ..................................................................... 12 Serial Interface Read/Write Examples ..................................... 54 Output Signal Handling............................................................. 12 PCB Layout Recommendations.................................................... 55 Clamping ..................................................................................... 12 Analog Interface Inputs ............................................................. 55 Timing.......................................................................................... 16 Power Supply Bypassing ............................................................ 55 HDMI Receiver........................................................................... 20 PLL ............................................................................................... 55 DE Generator .............................................................................. 20 Outputs (Both Data and Clocks).............................................. 56 4:4:4 to 4:2:2 Filter ...................................................................... 20 Digital Inputs .............................................................................. 56 Audio PLL Setup......................................................................... 21 Color Space Converter (CSC) Common Settings...................... 57 Audio Board Level Muting........................................................ 21 Outline Dimensions ....................................................................... 59 Timing Diagrams........................................................................ 22 Ordering Guide .......................................................................... 59 REVISION HISTORY 10/05--Revision 0: Initial Version Rev. 0 | Page 2 of 60 AD9380 SPECIFICATIONS ANALOG INTERFACE ELECTRICAL CHARACTERISTICS VDD, VD = 3.3 V, DVDD = PVDD = 1.8 V, ADC clock = maximum. Table 1. Parameter RESOLUTION DC ACCURACY Differential Nonlinearity Integral Nonlinearity No Missing Codes ANALOG INPUT Input Voltage Range Minimum Maximum Gain Tempco Input Bias Current Input Full-Scale Matching Offset Adjustment Range SWITCHING PERFORMANCE 1 Maximum Conversion Rate Minimum Conversion Rate Data-to-Clock Skew SERIAL PORT TIMING tBUFF tSTAH tDHO tDAL tDAH tDSU tSTASU tSTOSU HSYNC Input Frequency Maximum PLL Clock Rate Minimum PLL Clock Rate PLL Jitter Sampling Phase Tempco DIGITAL INPUTS, 5 V TOLERANT Input Voltage, High (VIH) Input Voltage, Low (VIL) Input Current, High (IIH) Input Current, Low (IIL) Input Capacitance DIGITAL OUTPUTS Output Voltage, High (VOH) Output Voltage, Low (VOL) Duty Cycle, DATACK Output Coding Min AD9380KSTZ-100 Typ Max 8 Temp Test Level 25C 25C Full I I I Full Full 25C 25C 25C Full Full VI VI V V VI VI V Full Full Full VI VI IV Full Full Full Full Full Full Full Full Full Full Full 25C Full VI VI VI VI VI VI VI VI VI VI IV IV IV 4.7 4.0 0 4.7 4.0 250 4.7 4.0 15 100 Full Full Full Full 25C VI VI V V V 2.6 Full Full Full VI VI V VDD - 0.1 Min AD9380KSTZ-150 Typ Max 8 -0.6 +1.6/-1.0 1.0 2.1 Guaranteed 0.7 +1.8/-1.0 1.1 2.25 Guaranteed 0.5 1.0 0.5 1.0 100 0.2 1.25 1.50 50 220 1 1.25 1.50 50 5 7 100 150 10 +2.0 -0.5 110 10 +2.0 -0.5 4.7 4.0 0 4.7 4.0 250 4.7 4.0 15 150 110 12 12 700 15 700 15 2.6 0.8 0.8 -82 82 3 45 5 7 -82 82 3 VDD - 0.1 50 Binary Rev. 0 | Page 3 of 60 0.4 55 45 50 Binary 0.4 55 Unit Bits LSB LSB VDD V p-p V p-p ppm/C A %FS %FS %FS MSPS MSPS ns s s s s s ns s s kHz MHz MHz ps p-p ps/C V V A A pF V V % AD9380 Parameter POWER SUPPLY VD Supply Voltage DVDD Supply Voltage VDD Supply Voltage PVDD Supply Voltage ID Supply Current (VD) IDVDD Supply Current (DVDD) IDD Supply Current (VDD) 2 IPVDD Supply Current (PVDD) Total Power Power-Down Dissipation DYNAMIC PERFORMANCE Analog Bandwidth, Full Power Signal-to-Noise Ratio (SNR) Without Harmonics fIN = 40.7 MHz Crosstalk THERMAL CHARACTERISTICS JA Junction-to-Ambient 1 2 3 AD9380KSTZ-100 Typ Max AD9380KSTZ-150 Typ Max Temp Test Level Min Full Full Full Full 25C 25C 25C 25C Full Full IV IV IV IV VI VI VI VI VI VI 3.15 1.7 1.7 1.7 25C 25C V I 330 46 330 46 MHz dB Full Full V V 45 60 45 60 dB dBc V 35 35 C/W 3.3 1.8 3.3 1.8 260 45 37 10 1.1 130 3.47 1.9 3.47 1.9 300 60 100 3 15 1.4 Min 3.15 1.7 1.7 1.7 3.3 1.8 3.3 1.8 Unit 3.47 1.9 3.47 1.9 330 85 1303 20 1.4 1.15 130 V V V V mA mA mA mA W mW Drive strength = high. DATACK load = 15 pF, data load = 5 pF. Specified current and power values with a worst-case pattern (on/off). DIGITAL INTERFACE ELECTRICAL CHARACTERISTICS VDD = VD =3.3 V, DVDD = PVDD = 1.8 V, ADC clock = maximum. Table 2. AD9380KSTZ-100 Parameter RESOLUTION DC DIGITAL I/O SPECIFICATIONS High-Level Input Voltage (VIH) Low-Level Input Voltage (VIL) High-Level Output Voltage (VOH) Low-Level Output Voltage (VOL) DC SPECIFICATIONS Output High Level IOHD (VOUT = VOH) Output Low Level IOLD (VOUT = VOL) DATACK High Level VOHC (VOUT = VOH) DATACK Low Level VOLC (VOUT = VOL) Differential Input Voltage, SingleEnded Amplitude Test Level Conditions VI VI VI VI IV IV IV IV IV IV IV IV Min Typ 8 Max 2.5 IV Typ 8 Max 0.8 0.8 0.1 0.1 36 24 12 8 40 20 30 15 75 Rev. 0 | Page 4 of 60 Min 2.5 VDD - 0.1 VDD - 0.1 Output drive = high Output drive = low Output drive = high Output drive = low Output drive = high Output drive = low Output drive = high Output drive = low AD9380KSTZ-150 36 24 12 8 40 20 30 15 700 75 Unit Bit V V V V mA mA mA mA mA mA mA mA 700 mV AD9380 AD9380KSTZ-100 Parameter POWER SUPPLY VD Supply Voltage VDD Supply Voltage DVDD Supply Voltage PVDD Supply Voltage IVD Supply Current (Typical Pattern) 1 IVDD Supply Current (Typical Pattern) 2 IDVDD Supply Current (Typical Pattern)1, 4 IPVDD Supply Current (Typical Pattern)1 Power-Down Supply Current (IPD) AC SPECIFICATIONS Intrapair (+ to -) Differential Input Skew (TDPS) Channel to Channel Differential Input Skew (TCCS) Low-to-High Transition Time for Data and Controls (DLHT) Test Level IV IV IV IV V V V V VI Typ Max Min Typ Max Unit 3.15 1.7 1.7 1.7 3.3 3.3 1.8 1.8 80 40 88 26 130 3.47 347 1.9 1.9 100 100 3 110 35 3.15 1.7 1.7 1.7 3.3 3.3 1.8 1.8 80 55 110 30 130 3.47 347 1.9 1.9 110 1753 145 40 V V V V mA mA mA mA 360 ps 6 900 Clock Period ps 1300 ps 650 ps 1200 ps 850 ps 1250 ps 800 ps 1200 ps +2.0 55 150 ns % MHz IV IV IV IV High-to-Low Transition Time for Data and Controls (DHLT) Min IV IV Low-to-High Transition Time for DATACK (DLHT) Conditions AD9380KSTZ-150 IV IV High-to-Low Transition Time for DATACK (DHLT) IV Clock-to-Data Skew 5 (TSKEW) Duty Cycle, DATACK5 DATACK Frequency (FCIP) IV IV IV VI Output drive = high; CL = 10 pF Output drive = low; CL = 5 pF Output drive = high; CL = 10 pF Output drive = low; CL = 5 pF Output drive = high; CL = 10 pF Output drive = low; CL = 5 pF Output drive = high; CL = 10 pF Output drive = low; CL = 5 pF -0.5 45 20 1 +2.0 50 The typical pattern contains a gray scale area, output drive = high. Worst-case pattern is alternating black and white pixels. The typical pattern contains a gray scale area, output drive = high. Specified current and power values with a worst-case pattern (on/off). 4 DATACK load = 10 pF, data load = 5 pF. 5 Drive strength = high. 2 3 Rev. 0 | Page 5 of 60 -0.5 AD9380 ABSOLUTE MAXIMUM RATINGS Table 3. Parameter VD VDD DVDD PVDD Analog Inputs Digital Inputs Digital Output Current Operating Temperature Range Storage Temperature Range Maximum Junction Temperature Maximum Case Temperature Rating 3.6 V 3.6 V 1.98 V 1.98 V VD to 0.0 V 5 V to 0.0 V 20 mA -25C to +85C -65C to +150C 150C 150C Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. EXPLANATION OF TEST LEVELS Table 4. Level I II III IV V VI Test 100% production tested. 100% production tested at 25C and sample tested at specified temperatures. Sample tested only. Parameter is guaranteed by design and characterization testing. Parameter is a typical value only. 100% production tested at 25C; guaranteed by design and characterization testing. ESD CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although this product features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. Rev. 0 | Page 6 of 60 AD9380 VDD RED 0 RED 1 RED 2 RED 3 RED 4 RED 5 RED 6 RED 7 GND VDD DATACK DE HSOUT SOGOUT VSOUT O/E FIELD SDA SCL PWRDN VD RAIN0 GND RAIN1 VD 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS GND 74 GAIN0 3 73 SOGIN 0 GREEN 5 4 72 VD GREEN 4 5 71 GAIN1 GREEN 3 6 70 SOGIN 1 GREEN 2 7 69 GND GREEN 1 8 68 BAIN0 GREEN 0 9 67 VD VDD 10 AD9380 66 BAIN1 GND 11 65 GND BLUE 7 12 TOP VIEW (Not to Scale) 64 HSYNC 0 BLUE 6 13 63 HSYNC 1 BLUE 5 14 62 EXTCLK/COAST BLUE 4 15 61 VSYNC 0 BLUE 3 16 60 VSYNC 1 BLUE 2 17 59 PVDD BLUE 1 18 58 GND BLUE 0 19 57 FILT MCLKIN 20 56 PVDD MCLKOUT 21 55 GND SCLK 22 54 PVDD LRCLK 23 53 ALGND I2S3 24 52 PU1 I2S2 25 51 PU2 39 40 41 42 43 44 45 46 47 48 49 50 GND Rx2- Rx2+ GND RxC+ RxC- VD RTERM GND DVDD DDCSCL DDCSDA 34 Rx0- 38 33 VD Rx1+ 32 DVDD 37 31 GND Rx1- 30 DVDD 36 29 GND GND 28 S/PDIF 35 27 Rx0+ 26 GREEN 6 PIN 1 I2S0 2 I2S1 1 05688-002 75 GND GREEN 7 Figure 2. Pin Configuration Table 5. Complete Pinout List Pin Type INPUTS Pin No. 79 77 74 71 68 66 64 63 61 60 73 70 62 62 81 Mnemonic RAIN0 RAIN1 GAIN0 GAIN1 BAIN0 BAIN1 HSYNC 0 HSYNC 1 VSYNC 0 VSYNC 1 SOGIN 0 SOGIN 1 EXTCLK COAST PWRDN B B Function Analog Input for Converter R Channel 0 Analog Input for Converter R Channel 1 Analog Input for Converter G Channel 0 Analog Input for Converter G Channel 1 Analog Input for Converter B Channel 0 Analog Input for Converter B Channel 1 Horizontal SYNC Input for Channel 0 Horizontal SYNC Input for Channel 1 Vertical SYNC Input for Channel 0 Vertical SYNC Input for Channel 1 Input for Sync-on-Green Channel 0 Input for Sync-on-Green Channel 1 External Clock Input--Shares Pin with COAST PLL COAST Signal Input--Shares Pin with EXTCLK Power-Down Control Rev. 0 | Page 7 of 60 Value 0.0 V to 1.0 V 0.0 V to 1.0 V 0.0 V to 1.0 V 0.0 V to 1.0 V 0.0 V to 1.0 V 0.0 V to 1.0 V 3.3 V CMOS 3.3 V CMOS 3.3 V CMOS 3.3 V CMOS 0.0 V to 1.0 V 0.0 V to 1.0 V 3.3 V CMOS 3.3 V CMOS 3.3 V CMOS AD9380 Pin Type OUTPUTS REFERENCES POWER SUPPLY CONTROL HDCP AUDIO DATA OUTPUTS Pin No. 92 to 99 2 to 9 12 to 19 89 87 85 86 84 57 80, 76, 72, 67, 45, 33 100, 90, 10 59, 56, 54 48, 32, 30 Mnemonic RED [7:0] GREEN [7:0] BLUE [7:0] DATACK HSOUT VSOUT SOGOUT O/E FIELD FILT VD Function Outputs of Red Converter, Bit 7 is MSB Outputs of Green Converter, Bit 7 is MSB Outputs of Blue Converter, Bit 7 is MSB Data Output Clock HSYNC Output Clock (Phase-Aligned with DATACK) VSYNC Output Clock (Phase-Aligned with DATACK) SOG Slicer Output Odd/Even Field Output Connection for External Filter Components For PLL Analog Power Supply and DVI Terminators Value VDD VDD VDD VDD VDD VDD VDD VDD 82 83 49 50 51 52 28 27 26 25 24 20 21 22 23 VDD PVDD DVDD GND SCL SDA DDCSCL DDCSDA PU2 PU1 S/PDIF I2S0 I2S1 I2S2 I2S3 MCLKIN MCLKOUT SCLK LRCLK Output Power Supply PLL Power Supply Digital Logic Power Supply Ground Serial Port Data Clock Serial Port Data I/O HDCP Slave Serial Port Data Clock HDCP Slave Serial Port Data I/O Should be tied to 3.3 V through a 10 k resistor Should be tied to 3.3 V through a 10 k resistor S/PDIF Digital Audio Output I2S Audio (Channel 1, Channel 2) I2S Audio (Channel 3, Channel 4) I2S Audio (Channel 5, Channel 6) I2S Audio (Channel 7, Channel 8) External Reference Audio Clock In Audio Master Clock Output Audio Serial Clock Output Data Output Clock for Left And Right Audio Channels 34 35 37 38 40 41 43 Rx0- Rx0+ Rx1- Rx1+ Rx2- Rx2+ RxC+ Digital Input Channel 0 Complement Digital Input Channel 0 True Digital Input Channel 1 Complement Digital Input Channel 1 True Digital Input Channel 2 Complement Digital Input Channel 2 True Digital Data Clock True 1.8 V to 3.3 V 1.8 V 1.8 V 0V 3.3 V CMOS 3.3 V CMOS 3.3 V CMOS 3.3 V CMOS 3.3 V CMOS 3.3 V CMOS VDD VDD VDD VDD VDD VDD VDD VDD VDD TMDS TMDS 44 88 46 RxC- DE RTERM Digital Data Clock Complement Data Enable Sets Internal Termination Resistance DIGITAL VIDEO DATA DIGITAL VIDEO CLOCK INPUTS DATA ENABLE RTERM Rev. 0 | Page 8 of 60 3.3 V TMDS TMDS TMDS TMDS 3.3 V CMOS 500 AD9380 Table 6. Pin Function Descriptions Mnemonic INPUTS RAIN0 GAIN0 BAIN0 RAIN1 GAIN1 BAIN1 B B Rx0+ Rx0- Rx1+ Rx1- Rx2+ Rx2- RxC+ RxC- HSYNC 0 HSYNC 1 VSYNC0 VSYNC1 SOGIN 0 SOGIN 1 EXTCLK/COAST Description Analog Input for the Red Channel 0. Analog Input for the Green Channel 0. Analog Input for the Blue Channel 0. Analog Input for the Red Channel 1. Analog Input for the Green Channel 1. Analog Input for Blue Channel 1. High impedance inputs that accept the red, green, and blue channel graphics signals, respectively. The three channels are identical and can be used for any colors, but colors are assigned for convenient reference. They accommodate input signals ranging from 0.5 V to 1.0 V full scale. Signals should be ac-coupled to these pins to support clamp operation (see Figure 3 for an input reference circuit). Digital Input Channel 0 True. Digital Input Channel 0 Complement. Digital Input Channel 1 True. Digital Input Channel 1 Complement. Digital Input Channel 2 True. Digital input Channel 2 Complement. These six pins receive three pairs of transition minimized differential signaling (TMDS) pixel data (at 10x the pixel rate) from a digital graphics transmitter. Digital Data Clock True. Digital Data Clock Complement. This clock pair receives a TMDS clock at 1x pixel data rate. Horizontal Sync Input Channel 0. Horizontal Sync Input Channel 1. These inputs receive a logic signal that establishes the horizontal timing reference and provides the frequency reference for pixel clock generation. The logic sense of this pin is controlled by Serial Register 0x12 Bits 5:4 (HSYNC polarity). Only the leading edge of HSYNC is active; the trailing edge is ignored. When HSYNC polarity = 0, the falling edge of HSYNC is used. When HSYNC polarity = 1, the rising edge is active. The input includes a Schmitt trigger for noise immunity. Vertical Sync Input Channel 0. Vertical Sync Input Channel 1. These are the inputs for vertical sync. Sync-on-Green Input Channel 0. Sync-on-Green Input Channel 1. These inputs are provided to assist with processing signals with embedded sync, typically on the green channel. The pin is connected to a high speed comparator with an internally generated threshold. The threshold level can be programmed in 10 mV steps to any voltage between 10 mV and 330 mV above the negative peak of the input signal. The default voltage threshold is 150 mV. When connected to an ac-coupled graphics signal with embedded sync, it produces a noninverting digital output on SOGOUT. (This is usually a composite sync signal, containing both vertical and horizontal sync (HSYNC ) information that must be separated before passing the horizontal sync signal to HSYNC.) When not used, this input should be left unconnected. For more details on this function and how it should be configured, see the HSYNC and VSYNC Inputs section. Coast Input to Clock Generator (Optional). This input can be used to cause the pixel clock generator to stop synchronizing with HSYNC and continue producing a clock at its current frequency and phase. This is useful when processing signals from sources that fail to produce horizontal sync pulses during the vertical interval. The coast signal is generally not required for PCgenerated signals. The logic sense of this pin is controlled by coast polarity (Register 0x18, Bits 6:5). When not used, this pin can be grounded and input coast polarity programmed to 1 (Register 0x18, Pin 5) or tied high (to VD through a 10 k resistor) and input coast polarity programmed to 0. Input coast polarity defaults to 1 at power-up. This pin is shared with the EXTCLK function, which does not affect coast functionality. For more details on coast, see the Clock Generation section. Rev. 0 | Page 9 of 60 AD9380 Mnemonic EXTCLK/COAST PWRDN FILT OUTPUTS HSOUT VSOUT SOGOUT O/E FIELD SERIAL PORT SDA SCL DDCSDA DDCSCL DATA OUTPUTS Red [7:0] Green [7:0] Blue [7:0] DATA CLOCK OUTPUT DATACK Description External Clock. This allows the insertion of an external clock source rather than the internally generated PLL-locked clock. This pin is shared with the coast function, which does not affect EXTCLK functionality. Power-Down Control/Three-State Control. The function of this pin is programmable via Register 0x26 [2:1]. External Filter Connection. For proper operation, the pixel clock generator PLL requires an external filter. Connect the filter shown in Figure 6 to this pin. For optimal performance, minimize noise and parasitics on this node. For more information see the PCB Layout Recommendations section . Horizontal Sync Output. A reconstructed and phase-aligned version of the HSYNC input. Both the polarity and duration of this output can be programmed via serial bus registers. By maintaining alignment with DATACK and data, data timing with respect to horizontal sync can always be determined. Vertical Sync Output. The separated VSYNC from a composite signal or a direct pass through of the VSYNC signal. The polarity of this output can be controlled via the serial bus bit (Register 0x24 [6]). Sync-on-Green Slicer Output. This pin outputs one of four possible signals (controlled by Register 0x1D [1:0]): raw SOG, raw HSYNC, regenerated HSYNC from the filter, or the filtered HSYNC. See the Sync processing block diagram (see Figure 8 for pin connections). Note that besides slicing off SOG, the output from this pin is not processed on the AD9380. VSYNC separation is performed via the sync separator. Odd/Even Field Bit for Interlaced Video. This output identifies whether the current field (in an interlaced signal) is odd or even. The polarity of this signal is programmable via Register 0x24[4]. Serial Port Data I/O for Programming AD9380 Registers--I2C Address is 0x98. Serial Port Data Clock for Programming AD9380 Registers. Serial Port Data I/O for HDCP Communications to Transmitter--I2C Address is 0x74 or 0x76. Serial Port Data Clock for HDCP Communications to Transmitter. Should be tied to 3.3 V through a 10 k resistor. Data Output, Red Channel. Data Output, Green Channel. Data Output, Blue Channel. The main data outputs. Bit 7 is the MSB. The delay from pixel sampling time to output is fixed, but is different if the color space converter is used. When the sampling time is changed by adjusting the phase register, the output timing is shifted as well. The DATACK and HSOUT outputs are also moved, so the timing relationship among the signals is maintained. Data Clock Output. This is the main clock output signal used to strobe the output data and HSOUT into external logic. Four possible output clocks can be selected with Register 0x25 [7:6]. These are related to the pixel clock (1/2x pixel clock, 1x pixel clock, 2x frequency pixel clock, and a 90 phase shifted pixel clock). They are produced either by the internal PLL clock generator or EXTCLK and are synchronous with the pixel sampling clock. The polarity of DATACK can also be inverted via Register 0x24 [0]. The sampling time of the internal pixel clock can be changed by adjusting the phase register. When this is changed, the pixel-related DATACK timing is shifted as well. The DATA, DATACK, and HSOUT outputs are all moved, so the timing relationship among the signals is maintained. Rev. 0 | Page 10 of 60 AD9380 Mnemonic POWER SUPPLY 1 VD (3.3 V) VDD (1.8 V to 3.3 V) PVDD (1.8 V) DVDD (1.8 V) GND 1 Description Analog Power Supply. These pins supply power to the ADCs and terminators. They should be as quiet and filtered as possible. Digital Output Power Supply. A large number of output pins (up to 27) switching at high speed (up to 150 MHz) generates many power supply transients (noise). These supply pins are identified separately from the VD pins, so output noise transferred into the sensitive analog circuitry can be minimized. If the AD9380 is interfacing with lower voltage logic, VDD may be connected to a lower supply voltage (as low as 1.8 V) for compatibility. Clock Generator Power Supply. The most sensitive portion of the AD9380 is the clock generation circuitry. These pins provide power to the clock PLL and help the user design for optimal performance. The designer should provide quiet, noise-free power to these pins. Digital Input Power Supply. This supplies power to the digital logic. Ground. The ground return for all circuitry on chip. It is recommended that the AD9380 be assembled on a single solid ground plane, with careful attention to ground current paths. The supplies should be sequenced such that VD and VDD are never less than 300 mV below DVDD. At no time should DVDD be more than 300 mV greater than VD or VDD. Rev. 0 | Page 11 of 60 AD9380 DESIGN GUIDE The AD9380 is a fully integrated solution for capturing analog RGB or YUV signals and digitizing them for display on flat panel monitors, projectors, or plasma display panels (PDPs). In addition, the AD9380 has a digital interface for receiving DVI/HDMI signals and is capable of decoding HDCPencrypted signals through connections to an internal EEPROM. The circuit is ideal for providing an interface for HDTV monitors or as the front end to high performance video scan converters. Implemented in a high performance CMOS process, the interface can capture signals with pixel rates of up to 150 MHz. The AD9380 includes all necessary input buffering, signal dc restoration (clamping), offset and gain (brightness and contrast) adjustment, pixel clock generation, sampling phase control, and output data formatting. Included in the output formatting is a color space converter (CSC), which accommodates any input color space and can output any color space. All controls are programmable via a 2-wire serial interface. Full integration of these sensitive analog functions makes system design straightforward and less sensitive to the physical and electrical environments. DIGITAL INPUTS All digital control inputs (HSYNC, VSYNC, and I2C) on the AD9380 operate to 3.3 V CMOS levels. In addition, all digital inputs, except the TMDS (HDMI/DVI) inputs, are 5 V tolerant. (Applying 5 V to them does not cause any damage.) TMDS inputs (Rx0+/Rx0-, Rx1+/Rx1-, Rx2+/Rx2-, and RxC+/RxC-) must maintain a 100 differential impedance (through proper PCB layout) from the connector to the input where they are internally terminated (50 to 3.3 V). If additional ESD protection is desired, use of a California Micro Devices (CMD) CM1213 series low capacitance ESD protection (among others) offers 8 kV of protection to the HDMI TMDS lines. In an ideal world of perfectly matched impedances, the best performance can be obtained with the widest possible signal bandwidth. The ultrawide bandwidth inputs of the AD9380 (330 MHz) can track the input signal continuously as it moves from one pixel level to the next, and digitizes the pixel during a long, flat pixel time. In many systems, however, there are mismatches, reflections, and noise, which can result in excessive ringing and distortion of the input waveform. This makes it more difficult to establish a sampling phase that provides good image quality. It has been shown that a small inductor in series with the input is effective in rolling off the input bandwidth slightly, and providing a high quality signal over a wider range of conditions. Using a Fair-Rite #2508051217Z0 high speed signal chip bead inductor in the circuit, as shown in Figure 3, gives good results in most applications. 47nF RGB INPUT 75 RAIN GAIN BAIN 05688-003 GENERAL DESCRIPTION Figure 3. Analog Input Interface Circuit HSYNC AND VSYNC INPUTS The interface also takes a horizontal sync signal, which is used to generate the pixel clock and clamp timing. This can be either a sync signal directly from the graphics source or a preprocessed TTL or CMOS level signal. The HSYNC input includes a Schmitt trigger buffer for immunity to noise and signals with long rise times. In typical PC-based graphic systems, the sync signals are simply TTLlevel drivers feeding unshielded wires in the monitor cable. As such, no termination is required. SERIAL CONTROL PORT The serial control port is designed for 3.3 V logic. However, it is tolerant of 5 V logic signals. ANALOG INPUT SIGNAL HANDLING OUTPUT SIGNAL HANDLING The AD9380 has six high impedance analog input pins for the red, green, and blue channels. They accommodate signals ranging from 0.5 V p-p to 1.0 V p-p. The digital outputs (VDD) operate from 1.8 V to 3.3 V. Signals are typically brought onto the interface board via a DVI-I connector, a 15-pin D connector, or RCA-type connectors. The AD9380 should be located as close as practical to the input connector. Signals should be routed via 75 matched impedance traces to the IC input pins. To properly digitize the incoming signal, the dc offset of the input must be adjusted to fit the range of the on-board ADC. At the input of the AD9380, the signal should be resistively terminated (75 to the signal ground return) and capacitively coupled to the AD9380 inputs through 47 nF capacitors. These capacitors form part of the dc restoration circuit. CLAMPING RGB Clamping Most graphics systems produce RGB signals with black at ground and white at approximately 0.75 V. However, if sync signals are embedded in the graphics, the sync tip is often at ground and black is at 300 mV. Then white is at approximately 1.0 V. Some common RGB line amplifier boxes use emitterfollower buffers to split signals and increase drive capability. This introduces a 700 mV dc offset to the signal, which must be removed for proper capture by the AD9380. Rev. 0 | Page 12 of 60 AD9380 The key to clamping is to identify a portion (time) of the signal when the graphic system is known to be producing black. An offset is then introduced which results in the ADCs producing a black output (Code 0x00) when the known black input is present. The offset then remains in place when other signal levels are processed, and the entire signal is shifted to eliminate offset errors. YUV Clamping In most pc graphics systems, black is transmitted between active video lines. With CRT displays, when the electron beam has completed writing a horizontal line on the screen (at the right side), the beam is deflected quickly to the left side of the screen (called horizontal retrace) and a black signal is provided to prevent the beam from disturbing the image. Clamping to midscale rather than ground can be accomplished by setting the clamp select bits in the serial bus register. Each of the three converters has its own selection bit so that they can be clamped to either midscale or ground independently. These bits are located in Register 0x1B [7:5]. The midscale reference voltage is internally generated for each converter. In systems with embedded sync, a blacker-than-black signal (HSYNC) is produced briefly to signal the CRT that it is time to begin a retrace. For obvious reasons, it is important to avoid clamping on the tip of HSYNC. Fortunately, there is virtually always a period following HSYNC, called the back porch, where a good black reference is provided. This is the time when clamping should be done. Auto-Offset Clamp timing employs the AD9380 internal clamp timing generator. The clamp placement register is programmed with the number of pixel periods that should pass after the trailing edge of HSYNC before clamping starts. A second register (clamp duration) sets the duration of the clamp. These are both 8-bit values, providing considerable flexibility in clamp generation. The clamp timing is referenced to the trailing edge of HSYNC because, though HSYNC duration can vary widely, the back porch (black reference) always follows HSYNC. A good starting point for establishing clamping is to set the clamp placement to 0x08 (providing 8 pixel periods for the graphics signal to stabilize after sync) and to set the clamp duration to 0x14 (giving the clamp 20 pixel periods to re-establish the black reference). For three-level syncs embedded on the green channel, it is necessary to increase the clamp placement to beyond the positive portion of the sync. For example, a good clamp placement (Register 0x19) for a 720p input is 0x26. This delays the start of clamp by 38 pixel clock cycles after the rising edge of the three-level sync, allowing plenty of time for the signal to return to a black reference. Clamping is accomplished by placing an appropriate charge on the external input coupling capacitor. The value of this capacitor affects the performance of the clamp. If it is too small, there is a significant amplitude change during a horizontal line time (between clamping intervals). If the capacitor is too large, then it takes excessively long for the clamp to recover from a large change in the incoming signal offset. The recommended value (47 nF) results in recovering from a step error of 100 mV to within 1/2 LSB in 10 lines with a clamp duration of 20 pixel periods on a 75 Hz SXGA signal. YUV graphic signals are slightly different from RGB signals in that the dc reference level (black level in RGB signals) can be at the midpoint of the graphics signal rather than at the bottom. For these signals, it can be necessary to clamp to the midscale range of the ADC range (128) rather than thebottom of the ADC range (0). The auto-offset circuit works by calculating the required offset setting to yield a given output code during clamp. When this block is enabled, the offset setting in the I2C is seen as a desired clamp code rather than an actual offset. The circuit compares the output code during clamp to the desired code and adjusts the offset up or down to compensate. The offset on the AD9380 can be adjusted automatically to a specified target code. Using this option allows the user to set the offset to any value and be assured that all channels with the same value programmed into the target code match. This eliminates any need to adjust the offset at the factory. This function is capable of running continuously any time the clamp is asserted. There is an offset adjust register for each channel, namely the offset registers at the 0x08, 0x0A, and 0x0C addresses. The offset adjustment is a signed (twos complement) number with a 64 LSB range. The offset adjustment is added to whatever offset the auto-offset comes up with. For example, using a ground clamp, the target code is set to 4. To get this code, the auto-offset generates an offset of 68. If the offset adjustment is set to +10, the offset sent to the converter is 78. Likewise, if the offset adjust is set to -10, the offset sent to the converter is +58. Refer to Application Note AN-775, Implementing the AutoOffset Function of the AD9880, for a detailed description of how to use this function. Sync-on-Green (SOG) The SOG input operates in two steps. First, it sets a baseline clamp level from the incoming video signal with a negative peak detector. Second, it sets the sync trigger level to a programmable level (typically 150 mV) above the negative peak. The SOG input must be ac-coupled to the green analog input through its own capacitor. The value of the capacitor must be 1 nF 20%. If SOG is not used, this connection is not required. Note that the SOG signal is always negative polarity. Rev. 0 | Page 13 of 60 AD9380 For more detail on setting the SOG threshold and other SOGrelated functions, see the Sync Processing section. 47nF RAIN 47nF BAIN The PLL characteristics are determined by the loop filter design, the PLL charge pump current, and the VCO range setting. The loop filter design is shown in Figure 6. Recommended settings of the VCO range and charge pump current for VESA standard display modes are listed in Table 9. 47nF GAIN PVD RZ 1.5k Figure 4. Typical Clamp Configuration for RGB/YUV Applications FILT Clock Generation Figure 6. PLL Loop Filter Detail A PLL is employed to generate the pixel clock. In this PLL, the HSYNC input provides a reference frequency. A voltage controlled oscillator (VCO) generates a much higher pixel clock frequency. This pixel clock is divided by the PLL divide value (Register 0x01 and Register 0x02) and phase compared with the HSYNC input. Any error is used to shift the VCO frequency and maintain lock between the two signals. The stability of this clock is a very important element in providing the clearest and most stable image. During each pixel time, there is a period during which the signal slews from the old pixel amplitude and settles at its new value. This is followed by a time when the input voltage is stable before the signal must slew to a new value. The ratio of the slewing time to the stable time is a function of the bandwidth of the graphics DAC and the bandwidth of the transmission system (cable and termination). It is also a function of the overall pixel rate. Clearly, if the dynamic characteristics of the system remain fixed, then the slewing and settling time is likewise fixed. This time must be subtracted from the total pixel period, leaving the stable period. At higher pixel frequencies, the total cycle time is shorter and the stable pixel time also becomes shorter. PIXEL CLOCK CZ 80nF 05688-006 SOG 05688-004 1nF CP 8nF Four programmable registers are provided to optimize the performance of the PLL. These registers are: * The 12-bit divisor register (R0x01, R0x02). The input HSYNC frequency range can be any frequency which, combined with the PLL_Div, does not exceed the VCO range . The PLL multiplies the frequency of the HSYNC signal, producing pixel clock frequencies in the range of 10 MHz to 100 MHz. The divisor register controls the exact multiplication factor. * The 2-bit VCO range register (R0x03[7:6]). To improve the noise performance of the AD9380, the VCO operating frequency range is divided into four overlapping regions. The VCO range register sets this operating range. The frequency ranges for the lowest and highest regions are shown in Table 7. Table 7. VCORNGE 00 01 10 11 INVALID SAMPLE TIMES 05688-005 * Figure 5. Pixel Sampling Times Any jitter in the clock reduces the precision with which the sampling time can be determined and must also be subtracted from the stable pixel time. Considerable care has been taken in the design of the AD9380 clock generation circuit to minimize jitter. The clock jitter of the AD9380 is less than 13% of the total pixel time in all operating modes, making the reduction in the valid sampling time due to jitter negligible. Pixel Rate Range 12 to 30 30 to 60 60 to 120 120 to 150 The 5-bit phase adjust register (R0x04). The phase of the generated sampling clock can be shifted to locate an optimum sampling point within a clock cycle. The phase adjust register provides 32 phase-shift steps of 11.25 each. The HSYNC signal with an identical phase shift is available through the HSOUT pin. The coast pin or the internal coast is used to allow the PLL to continue to run at the same frequency, in the absence of the incoming HSYNC signal or during disturbances in HSYNC (such as equalization pulses). Coasting can be used during the vertical sync period or any other time that the HSYNC signal is unavailable. The polarity of the coast signal can be set through the coast polarity register. Also, the polarity of the HSYNC signal can be set through the HSYNC polarity register. For both HSYNC and coast, a value of 1 is active high. The internal coast function is driven off the VSYNC signal, which is typically a time when HSYNC signals can be disrupted with extra equalization pulses. Rev. 0 | Page 14 of 60 AD9380 Power Management The AD9380 uses the activity detect circuits, the active interface bits in the serial bus, the active interface override bits, the power-down bit, and the power-down pin to determine the correct power state. There are four power states: full-power, seek mode, auto power-down, and power-down. Table 8 summarizes how the AD9380 determines the power mode and the circuitry that is powered on/off in each of these modes. The power-down command has priority and then the automatic circuitry. The power-down pin (Pin 81--polarity set by Register 0x26[3]) can drive the chip into four power-down options. Bit 2 and Bit 1 of Register 0x26 control these four options. Bit 0 controls whether the chip is powered down or the outputs are placed in high impedance mode (with the exception of SOG). Bit 7 to Bit 4 of Register 0x26 control whether the outputs, SOG, Sony Philips digital interface (SPDIF ) or I2S (IIS or Inter-IC Sound bus) outputs are in high impedance mode or not. (See the 2-Wire Serial Control Register Detail section for more detail.) Table 8. Power-Down Mode Descriptions Mode Full Power Seek Mode Seek Mode Power-Down1 1 1 1 Inputs Sync Detect2 1 0 0 Power-Down 0 X Auto PD Enable3 X 0 1 Power-On or Comments Everything Everything Serial bus, sync activity detect, SOG, band gap reference Serial bus, sync activity detect, SOG, band gap reference 1 Power-down is controlled via Bit 0 in Serial Bus Register 0x26. Sync detect is determined by OR'ing Bit 7 to Bit 2 in Serial Bus Register 0x15. 3 Auto power-down is controlled via Bit 7 in Serial Bus Register 0x27. 2 Table 9. Recommended VCO Range and Charge Pump Current Settings for Standard Display Formats Standard VGA Resolution 640 x 480 SVGA 800 x 600 XGA 1024 x 768 SXGA 1280 x 1024 1280 x 1024 480i 480p 720p 1035i 1080i 1080p TV 1 Refresh Rate (Hz) 60 72 75 85 56 60 72 75 85 60 70 75 80 85 60 75 60 60 60 60 60 60 Horizontal Frequency (kHz) 31.5 37.7 37.5 43.3 35.1 37.9 48.1 46.9 53.7 48.4 56.5 60.0 64.0 68.3 64.0 80.0 15.75 31.47 45 33.75 33.75 67.5 Pixel Rate (MHz) 25.175 31.500 31.500 36.000 36.000 40.000 50.000 49.500 56.250 65.000 75.000 78.750 85.500 94.500 108.000 135.000 13.51 27 74.25 74.25 74.25 148.5 These are preliminary recommendations for the analog PLL and are subject to change without notice. Rev. 0 | Page 15 of 60 VCO Range1 00 01 01 01 01 01 01 01 01 10 10 10 10 10 10 11 00 00 10 10 10 11 Current1 101 011 100 100 100 101 110 110 110 011 100 100 101 110 110 110 010 101 100 100 100 110 AD9380 TIMING The output data clock signal is created so that its rising edge always occurs between data transitions and can be used to latch the output data externally. There is a pipeline in the AD9380, which must be flushed before valid data becomes available. This means 23 data sets are presented before valid data is available. Figure 7 shows the timing of the AD9380. Coast Timing tPER In most computer systems, the HSYNC signal is provided continuously on a dedicated wire. In these systems, the coast input and function are unnecessary and should not be used. The pin should be permanently connected to the inactive state. tDCYCLE DATACK tSKEW 05688-007 DATA HSOUT Three things happen to HSYNC in the AD9380. First, the polarity of the HSYNC input is determined and thus has a known output polarity. The known output polarity can be programmed either active high or active low (Register 0x24, Bit 7). Second, HSOUT is aligned with DATACK and the data outputs. Third, the duration of HSOUT (in pixel clocks) is set via Register 0x23. HSOUT is the sync signal to use to drive the rest of the display system. Figure 7. Output Timing HSYNC Timing Horizontal sync (HSYNC) is processed in the AD9380 to eliminate ambiguity in the timing of the leading edge with respect to the phase-delayed pixel clock and data. The HSYNC input is used as a reference to generate the pixel sampling clock. The sampling phase can be adjusted, with respect to HSYNC, through a full 360 in 32 steps via the phase adjust register (to optimize the pixel sampling time). Display systems use HSYNC to align memory and display write cycles, so it is important to have a stable timing relationship between the HSYNC output (HSOUT) and data clock (DATACK). In some systems, however, HSYNC is disturbed during the vertical sync period (VSYNC). In some cases, HSYNC pulses disappear. In other systems, such as those that employ composite sync (Csync) signals or embedded SOG, HSYNC includes equalization pulses or other distortions during VSYNC. To avoid upsetting the clock generator during VSYNC, it is important to ignore these distortions. If the pixel clock PLL sees extraneous pulses, it attempts to lock to this new frequency, and changes frequency by the end of the VSYNC period. It then takes a few lines of correct HSYNC timing to recover at the beginning of a new frame, which tears the image at the top of the display. The coast input is provided to eliminate this problem. It is an asynchronous input that disables the PLL input and allows the clock to free run at its then-current frequency. The PLL can free-run for several lines without significant frequency drift. Coast can be generated internally by the AD9380 (see Register 0x12 [1]), can be driven directly from a VSYNC input, or can also be provided externally by the graphics controller. Rev. 0 | Page 16 of 60 AD9380 Sync Processing is to extract VSYNC from the composite sync signal, which can come from either the sync slicer or the HSYNC input. The HSYNC filter is used to eliminate any extraneous pulses from the HSYNC or SOGIN inputs, outputting a clean, low jitter signal that is appropriate for mode detection and clock generation. The HSYNC regenerator is used to recreate a clean, although not low jitter, HSYNC signal that can be used for mode detection and for counting HSYNCs per VSYNC. The VSYNC filter is used to eliminate spurious VSYNCs, maintain a stable timing relationship between the VSYNC and HSYNC output signals, and generate the odd/even field output. The coast generator creates a robust coast signal that allows the PLL to maintain its frequency in the absence of HSYNC pulses. The inputs of the AD9380 sync processing section are combinations of digital HSYNCs and VSYNCs, analog sync-ongreen signal, sync-on-Y signal, and an optional external coast signal. From these signals, the AD9380 generates a precise, jitter-free (9% or less at 95 MHz) clock from its PLL; an odd/even field signal; HSYNC and VSYNC out signals; a count of HSYNCs per VSYNC; and a programmable SOG output. The main sync processing blocks are the sync slicer, sync separator, HSYNC filter, HSYNC regenerator, VSYNC filter, and coast generator. The sync slicer extracts the sync signal from the green graphics or luminance video signal that is connected to the SOGIN input and outputs a digital composite sync. The sync separator's task CHANNEL SELECT [0x11:3] HSYNC [0x11:7] SELECT HSYNC 0 MUX PD2 AD1 HSYNC FILTER AND REGENERATOR MUX HSYNC 1 AD1 FH4 PD2 RH3 SYNC SLICER SOGIN 0 MUX AD1 SYNC SLICER SOGIN 1 SP SYNC FILTER EN 0x21:7 MUX SP5 SOGOUT AD1 VSYNC 0 VSYNC AD1 PD2 AD1 PD2 MUX SOGOUT SELECT 0x24:2,1 SYNC PROCESSOR AND VSYNC FILTER MUX VSYNC FILTERED VSYNC MUX VSOUT VSYNC 1 VSYNC FILTER EN 0x21:5 FILTER COAST VSYNC 0x12:0 PLL SYNC FILTER EN 0x21:6 MUX HSYNC/VSYNC COUNTER REG 26H, 27H SP5 O/E FIELD HSYNC COAST MUX COAST AD9380 SP5 HSOUT SP5 DATACK PLL CLOCK GENERATOR COAST SELECT 0x12:1 05688-008 1ACTIVITY DETECT 2POLARITY DETECT 3REGENERATED HSYNC 4FILTERED HSYNC 5SET POLARITY Figure 8. Sync Processing Block Diagram Rev. 0 | Page 17 of 60 AD9380 Sync Slicer The purpose of the sync slicer is to extract the sync signal from the green graphics or luminance video signal that is connected to the SOGIN input. The sync signal is extracted in a two-step process. First, the SOG input (typically 0.3 V below the black level) is detected and clamped to a known dc voltage. Next, the signal is routed to a comparator with a variable trigger level (set by Register 0x1D, Bits [7:3]), but nominally 0.128 V above the clamped voltage. The sync slicer output is a digital composite sync signal containing both HSYNC and VSYNC information (see Figure 9). Sync Separator As part of sync processing, the sync separator's task is to extract VSYNC from the composite sync signal. It works on the idea that the VSYNC signal stays active for a much longer time than the HSYNC signal. By using a digital low-pass filter and a digital comparator, it rejects pulses with small durations (such as HSYNCs and equalization pulses) and only passes pulses with large durations, such as VSYNC (see Figure 9). The threshold of the digital comparator is programmable for maximum flexibility. To program the threshold duration, write a value (N) to Register 0x11. The resulting pulse width is N x 200 ns. So, if N = 5 the digital comparator threshold is 1 s. Any pulses less than 1 s are rejected, while any pulses greater than 1 s pass through. The sync separator on the AD9380 is simply an 8-bit digital counter with a 6 MHz clock. It works independently of the polarity of the composite sync signal. Polarities are determined elsewhere on the chip. The basic idea is that the counter counts up when HSYNC pulses are present. But because HSYNC pulses are relatively short in width, the counter only reaches a value of N before the pulse ends. It then starts counting down until eventually reaching 0 before the next HSYNC pulse arrives. The specific value of N varies for different video modes, but is always less than 255. For example, with a 1 s width HSYNC, the counter only reaches 5 (1 s/200 ns = 5). Now, when VSYNC is present on the composite sync, the counter also counts up. However, because the VSYNC signal is much longer, it counts to a higher number, M. For most video modes, M is at least 255. So VSYNC can be detected on the composite sync signal by detecting when the counter counts to higher than N. The specific count that triggers detection, T, can be programmed through the Serial Register 0x11. Once VSYNC has been detected, there is a similar process to detect when it goes inactive. At detection, the counter first resets to 0, then starts counting up when VSYNC finishes. As in the previous case, it detects the absence of VSYNC when the counter reaches the threshold count, T. In this way, it rejects noise and/or serration pulses. Once VSYNC is detected to be absent, the counter resets to 0 and begins the cycle again. There are two things to keep in mind when using the sync separator. First, the resulting clean VSYNC output is delayed from the original VSYNC by a duration equal to the digital comparator threshold (N x 200 ns). Second, there is some variability to the 200 ns multiplier value. The maximum variability over all operating conditions is 20% (160 ns to 240 ns). Because normal VSYNC and HSYNC pulse widths differ by a factor of about 500 or more, 20% variability is not an issue. NEGATIVE PULSE WIDTH = 40 SAMPLE CLOCKS 700mV MAXIMUM SOGIN +300mV 0mV -300mV SOGOUT OUTPUT CONNECTED TO HSIN 05688-009 COMPOSITE SYNC AT HSIN VSOUT FROM SYNC SEPARATOR Figure 9. Sync Slicer and Sync Separator Output Rev. 0 | Page 18 of 60 AD9380 HSYNC Filter and Regenerator The HSYNC filter is used to eliminate any extraneous pulses from the HSYNC or SOGIN inputs, outputting a clean, low jitter signal that is appropriate for mode detection and clock generation. The HSYNC regenerator is used to re-create a clean, although not low jitter, HSYNC signal that can be used for mode detection and counting HSYNCs per VSYNC. The HSYNC regenerator has a high degree of tolerance to extraneous and missing pulses on the HSYNC input, but is not appropriate for use by the PLL in creating the pixel clock because of jitter. The HSYNC regenerator runs automatically and requires no setup to operate. The HSYNC filter requires the setting up of a filter window. The filter window sets a periodic window of time around the regenerated HSYNC leading edge, where valid HSYNCs are allowed to occur. The general idea is that extraneous pulses on the sync input occur outside of this filter window and thus are filtered out. To set the filter window timing, program a value (x) into Register 0x20. The resulting filter window time is x times 25 ns either side of the regenerated HSYNC leading edge. Just as for the sync separator threshold multiplier, allow a 20% variance in the 25 ns multiplier to account for all operating conditions (20 ns to 30 ns range). A second output from the HSYNC filter is a status bit (Register 0x16[0]) that tells whether extraneous pulses are present on the incoming sync signal. Extraneous pulses are often included for copy protection purposes, which this status bit can detect. The filtered HSYNC (rather than the raw HSYNC/SOGIN signal) for pixel clock generation by the PLL is controlled by Register 0x21[6]. The regenerated HSYNC (rather than the raw HSYNC/SOGIN signal) for sync processing is controlled by Register 0x21[7]. Use of the filtered HSYNC and regenerated HSYNC is recommended. Figure 10 shows a filtered HSYNC. HSIN FILTER WINDOW HSOUT VSYNC EQUALIZATION PULSES EXPECTED EDGE 05688-010 FILTER WINDOW Figure 10. Sync Processing Filter Rev. 0 | Page 19 of 60 AD9380 VSYNC Filter and Odd/Even Fields The VSYNC filter is used to eliminate spurious VSYNCs, maintain a consistent timing relationship between the VSYNC and HSYNC output signals, and generate the odd/even field output. The filter works by examining the placement of VSYNC with respect to HSYNC and, if necessary, slightly shifting it in time at the VSOUT output. The goal is to keep the VSYNC and HSYNC leading edges from switching at the same time, eliminating confusion as to when the first line of a frame occurs. Enabling the VSYNC filter is done with Register 0x21[5]. Use of the VSYNC filter is recommended for all cases, including interlaced video, and is required when using the HSYNC per VSYNC counter. Figure 11 and Figure 12 illustrates even/odd field determination in two situations. SYNC SEPARATOR THRESHOLD FIELD 1 QUADRANT 2 3 FIELD 0 4 1 FIELD 1 2 3 FIELD 0 4 1 The earlier digital visual interface (DVI) format was restricted to an RGB 24-bit color space only. Embedded in this data stream were HSYNCs, VSYNCs, and display enable (DE) signals, but no audio information. The HDMI specification allows transmission of all the DVI capabilities, but adds several YCrCb formats that make the inclusion of a programmable color space converter (CSC) a very desirable feature. With this, the scaler following the AD9380 can specify that it always wishes to receive a particular format--for instance, 4:2:2 YCrCb--regardless of the transmitted mode. If RGB is sent, the CSC can easily convert that to 4:2:2 YCrCb while relieving the scaler of this task. In addition, the HDMI specification supports the transmission of up to eight channels of S/PDIF or I2S audio. The audio information is packetized and transmitted during the video blanking periods along with specific information about the clock frequency. Part of this audio information (audio infoframe) tells the user how many channels of audio are present, where they should be placed, information regarding the source (make, model), and other data. HSIN DE GENERATOR VSIN The AD9380 has an onboard generator for DE, for start of active video (SAV), and for end of active video (EAV), all of which are necessary for describing the complete data stream for a BT656-compatible output. In addition to this particular output, it is possible to generate the DE for cases in which a scaler is not used. This signal alerts the circuitry following the AD9380 which video pixels are displayable. 05688-011 VSOUT O/E FIELD EVEN FIELD Figure 11. VSYNC Filter--Even SYNC SEPARATOR THRESHOLD 4:4:4 TO 4:2:2 FILTER FIELD 1 QUADRANT 2 FIELD 0 3 4 1 FIELD 1 2 3 FIELD 0 4 The AD9380 contains a filter that allows it to convert a signal from YCrCb 4:4:4 to YCrCb 4:2:2 while maintaining the maximum accuracy and fidelity of the original signal. 1 HSIN VSIN Input Color Space to Output Color Space O/E FIELD ODD FIELD 05688-012 VSOUT Figure 12. VSYNC Filter--Odd The AD9380 can accept a wide variety of input formats and either retain that format or convert to another. Input formats supported are: * 4:4:4 YCrCb 8-bit HDMI RECEIVER * 4:2:2 YCrCb 8-, 10-, and 12-bit The HDMI receiver section of the AD9380 allows the reception of a digital video stream, which is backward compatible with DVI and able to accommodate not only video of various formats (RGB, YCrCb 4:4:4, 4:2:2), but also up to eight channels of audio. Infoframes are transmitted carrying information about the video format, audio clocks, and many other items necessary for a monitor to use fully the information stream available. * RGB 8-bit Output modes supported are: * 4:4:4 YCrCb 8-bit * 4:2:2 YCrCb 8-, 10-, and 12-bit * Dual 4:2:2 YCrCb 8-bits Rev. 0 | Page 20 of 60 AD9380 Color Space Conversion (CSC) Matrix AUDIO PLL SETUP The CSC matrix in the AD9380 consists of three identical processing channels. In each channel, three input values are multiplied by three separate coefficients. Also included are an offset value for each row of the matrix and a scaling multiple for all values. Each value has a 13-bit, twos complement resolution to ensure the signal integrity is maintained. The CSC is designed to run at speeds up to 150 MHz, supporting resolutions up to 1080p at 60 Hz. With any-to-any color space support, formats such as RGB, YUV, YCbCr, and others are supported by the CSC. Data contained in the audio infoframes, among other registers, define for the AD9380 HDMI receiver not only the type of audio, but the sample frequency. It also contains information about the N and CTS values used to re-create the clock. With this information, it is possible to regenerate the audio sampling frequency. The audio clock is regenerated by dividing the 20-bit CTS value into the TMDS clock, then multiplying by the 20-bit N value. This yields a multiple of the sampling frequency (fS) of either 128 x fS or 256 x fS. It is possible for this to be specified up to 1024 x fS. SOURCE DEVICE Table 10. CSC Port Mapping Input Channel R/CR Gr/Y B/CB + + AUDIO BOARD LEVEL MUTING The audio can be muted through the infoframes or locally via the serial bus registers. Muting can be controlled with Register R0x57, Bits [7:4]. AVI Infoframes The HDMI TMDS transmission contains infoframes with specific information for the monitor such as: * Audio information o 2 to 8 channels of audio identified o Audio coding o Audio sampling frequency x4 2 * Speaker placement x2 1 * N and CTS values (for reconstruction of the audio) 0 * Muting * Source information o CD o SACD o DVD * Video information o Video ID Code (per CEA861B) o Color space + ROUT [11:0] a2[12:0] BIN [11:0] x x 1 4096 x x 05688-013 a3[12:0] GIN [11:0] MULTIPLY 128 x fS BY N Figure 14. N and CTS for Audio Clock CSC_Mode[1:0] 1 4096 DIVIDE BY CTS AND CTS VALUES ARE TRANSMITTED USING THE AUDIO CLOCK REGENERATION PACKET. VIDEO CLOCK IS TRANSMITTED ON TMDS CLOCK CHANNEL. a4[12:0] x CLOCK N1 1N B The functional diagram for a single channel of the CSC, as shown in Figure 13, is repeated for the remaining G and B channels. The coefficients for these channels are b1, b2, b3, b4, c1, c2, c3, and c4. x CTS1 TMDS REGISTER N N One of the three channels is represented in Figure 13. In each processing channel, the three inputs are multiplied by three separate coefficients marked a1, a2, and a3. These coefficients are divided by 4096 to obtain nominal values ranging from -0.9998 to +0.9998. The variable labeled a4 is used as an offset control. The CSC_Mode setting is the same for all three processing channels. This multiplies all coefficients and offsets by a factor of 2CSC_Mode. RIN [11:0] CYCLE TIME COUNTER VIDEO CLOCK CSC Input Channel RIN GIN BIN a1[12:0] DIVIDE BY N 128 x fS SINK DEVICE 1 4096 Figure 13. Single CSC Channel A programming example and register settings for several common conversions are listed in the Color Space Converter (CSC) Common Settings section. For a detailed functional description and more programming examples, refer to Application Note AN-795, AD9880 Color Space Converter User's Guide. * Rev. 0 | Page 21 of 60 o Aspect ratio o Horizontal and vertical bar information o MPEG frame information (I, B, or P frame) Vendor (transmitter source) name and product model 05688-014 The main inputs, RIN, GIN, and BIN come from the 8- to 12-bit inputs from each channel. These inputs are based on the input format detailed in Table 11 The mapping of these inputs to the CSC inputs is shown in Table 10. AD9380 This information is the fundamental difference between DVI and HDMI transmissions and is located in read-only registers R0x5A to R0xEE. In addition to this information, registers are provided to indicate that new information has been received. Registers with addresses ending in 0xX7 or 0xXF, beginning at R0x87 contain the new data flag (NDF) information. These registers contain the same information and all are reset once any of them are read. Although there is no external interrupt signal, the user easily can read any of these registers to see if there is new information to be processed. P0 DATAIN P1 P2 P3 P4 TIMING DIAGRAMS Figure 15 and Figure 16 show the operation of the AD9380.The output data clock signal is created so that its rising edge always occurs between data transitions and can be used to latch the output data externally. There is a pipeline in the AD9380 that must be flushed before valid data becomes available. This means six data sets are presented before valid data is available. P5 P6 P7 P8 P9 P10 P11 HSIN DATACK 8 CLOCK CYCLE DELAYS DATAOUT P0 P1 P2 P3 05688-015 2 CLOCK CYCLE DELAYS HSOUT Figure 15. RGB ADC Timing DATAIN P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 HSIN DATACK 8 CLOCK CYCLE DELAYS YOUT CB/CROUT Y0 Y1 Y2 Y3 B0 R0 B2 R2 2 1 2 CLOCK CYCLE DELAYS HSOUT 05688-016 NOTES: 1. PIXEL AFTER HSOUT CORRESPONDS TO BLUE INPUT. 2. EVEN NUMBER OF PIXEL DELAYS BETWEEN HSOUT AND DATAOUT. Figure 16. YCrCb ADC Timing Table 11. Port Bit 4:4:4 4:2:2 4:4:4 DDR 4:2:2 to 12 1 Red 7 6 5 4 Red/Cr [7:0] CbCr [7:0] DDR G [3:0] 1 DDR R [7:0]1 CbCR [11:0] 3 2 1 DDR B [7:4] 0 Green 7 6 5 Green/Y [7:0] Y [7:0] DDR B [3:0] DDR G [7:4] 4 Arrows in the table indicate clock edge. Rising edge of clock = , falling edge = . Rev. 0 | Page 22 of 60 3 0 DDR 4:2:2 CbCr [11:0] DDR 4:2:2 Y,Y [11:0] Y [11:0] Blue 7 6 5 4 3 2 Blue/Cb [7:0] DDR 4:2:2 CbCr Y, Y 1 0 AD9380 2-WIRE SERIAL REGISTER MAP The AD9380 is initialized and controlled by a set of registers that determines the operating modes. An external controller is employed to write and read the control registers through the 2-wire serial interface port. Table 12. Control Register Map Hex Address 0x00 0x01 0x02 0x03 Read/Write or Read-Only Read Read/Write Read/Write Read/Write Bits [7:0] [7:0] [7:4] [7:6] [5:3] [2] Default Value 00000000 01101001 1101**** 01****** **001*** *****0** Register Name Chip Revision PLL Divider MSB PLL Divider VCO Range Charge Pump External Clock Enable 0x04 0x05 Read/Write Read/Write [7:3] [7:0] 10000*** 10000000 Phase Adjust Red Gain 0x06 Read/Write [7:0] 10000000 Green Gain 0x07 Read/Write [7:0] 10000000 Blue Gain 0x08 Read/Write [7:0] 00000000 Red Offset Adjust 0x09 0x0A Read/Write Read/Write [7:0] [7:0] 10000000 00000000 Red Offset Green Offset Adjust 0x0B 0x0C Read/Write Read/Write [7:0] [7:0] 10000000 00000000 Green Offset Blue Offset Adjust 0x0D 0x0E Read/Write Read/Write [7:0] [7:0] 10000000 00100000 0x0F Read/Write [7:2] 010000** 0x10 Read/Write [7:2] 010000** 0x11 Read/Write [7] 0******* Blue Offset Sync Separator Threshold SOG Comparator Threshold Enter SOG Comparator Threshold Exit HSYNC Source [6] *0****** HSYNC Source Override [5] **0***** VSYNC Source [4] ***0**** VSYNC Source Override [3] ****0*** Channel Select [2] *****0** Channel Select Override [1] ******0* Interface Select [0] *******0 Interface Override Description Chip revision ID. PLL feedback divider value MSB. PLL feedback divider value. VCO range. Charge pump current control for PLL. Selects the external clock input rather than the internal PLL clock. Selects the clock phase to use for the ADC clock. Controls the gain of the red channel PGA. 0 = low gain, 255 = high gain. Controls the gain of the green channel PGA. 0 = low gain, 255 = high gain. Controls the gain of the blue channel PGA. 0 = low gain, 255 = high gain. User adjustment of auto-offset. Allows user control of brightness. Red offset/target code. 0 = small offset, 255 = large offset. User adjustment of auto-offset. Allows user control of brightness. Green offset/target code. 0 = small offset, 255 = large offset. User adjustment of auto-offset. Allows user control of brightness. Blue offset/target code. 0 = small offset, 255 = large offset. Selects the maximum HSYNC pulse width for composite sync separation. The enter level for the SOG slicer. Must be less than or equal to the exit level. The exit level for the SOG slicer. Must be greater than or equal to the enter level. 0 = HSYNC. 1 = SOG. 0 = auto HSYNC source. 1 = manual HSYNC source. 0 = VSYNC. 1 = VSYNC from SOG. 0 = auto HSYNC source. 1 = manual HSYNC source. 0 = Channel 0. 1 = Channel 1. 0 = autochannel select. 1 = manual channel select. 0 = analog interface. 1 = digital interface. 0 = auto-interface select. 1 = manual interface select. Rev. 0 | Page 23 of 60 AD9380 Hex Address 0x12 0x13 0x14 0x15 0x16 Read/Write or Read-Only Read/Write Read/Write Read/Write Read Read Bits [7] Default Value 1******* [6] *0****** HSYNC Polarity Override [5] **1***** Input VSYNC Polarity [4] ***0**** VSYNC Polarity Override [3] ****1*** Input Coast Polarity [2] *****0** Coast Polarity Override Register Name Input HSYNC Polarity [1] ******0* Coast Source [0] *******1 Filter Coast VSYNC [7:0] [7:0] [7] 00000000 00000000 0******* Precoast Postcoast HSYNC 0 Detected [6] *0****** HSYNC 1 Detected [5] **0***** VSYNC 0 Detected [4] ***0**** VSYNC 1 Detected [3] ****0*** SOG 0 Detected [2] *****0** SOG 1 Detected [1] ******0* Coast Detected [7] 0******* HSYNC 0 Polarity [6] *0****** HSYNC 1 Polarity [5] **0***** VSYNC 0 Polarity [4] ***0**** VSYNC 1 Polarity [3] ****0*** Coast Polarity [2] *****0** Pseudo Sync Detected [1] ******0* Sync Filter Locked [0] *******0 Bad Sync Detect Description 0 = active low. 1 = active high. 0 = auto HSYNC polarity. 1 = manual HSYNC polarity. 0 = active low. 1 = active high. 0 = auto VSYNC polarity. 1 = manual VSYNC polarity. 0 = active low. 1 = active high. 0 = auto coast polarity. 1 = manual coast polarity. 0 = internal coast. 1 = external coast. 0 = use raw VSYNC for coast generation. 1 = use filtered VSYNC for coast generation. Number of HSYNC periods before VSYNC to coast. Number of HSYNC periods after VSYNC to coast. 0 = not detected. 1 = detected. 0 = not detected. 1 = detected. 0 = not detected. 1 = detected. 0 = not detected. 1 = detected. 0 = not detected. 1 = detected. 0 = not detected. 1 = detected. 0 = not detected. 1 = detected. 0 = active low. 1 = active high. 0 = active low. 1 = active high. 0 = active low. 1 = active high. 0 = active low. 1 = active high. 0 = active low. 1 = active high. 0 = not detected. 1 = detected. 0 = not locked. 1 = locked. 0 = not detected. 1 = detected. Rev. 0 | Page 24 of 60 AD9380 Hex Address 0x17 Read/Write or Read-Only Read Bits [3:0] Default Value ****0000 0x18 0x19 Read Read/Write [7:0] [7:0] 00000000 00001000 Register Name HSYNCs per VSYNC MSB HSYNCs per VSYNC Clamp Placement 0x1A 0x1B Read/Write Read/Write [7:0] [7] 00010100 0******* Clamp Duration Red Clamp Select [6] *0****** Green Clamp Select [5] **0***** Blue Clamp Select [4] ***0**** Clamp During Coast Enable [3] ****0*** Clamp Disable [1] ******1* Programmable Bandwidth [0] *******0 Hold Auto-Offset [7] 0******* Auto-Offset Enable [6:5] *10***** Auto-Offset Update Mode [4:3] ***01*** Difference Shift Amount [2] *****1** Auto Jump Enable [1] ******1* Post Filter Enable [0] *******0 Toggle Filter Enable Slew Limit Sync Filter Lock Threshold Sync Filter Unlock Threshold Sync Filter Window Width SP Sync Filter Enable 0x1C Read/Write 0x1D 0x1E Read/Write Read/Write [7:0] [7:0] 00001000 32 0x1F Read/Write [7:0] 50 0x20 Read/Write [7:0] 50 0x21 Read/Write [7] 1******* Description MSB of HSYNCs per VSYNC. HSYNCs per VSYNC count. Number of pixel clocks after trailing edge of HSYNC to begin clamp. Number of pixel clocks to clamp. 0 = clamp to ground. 1 = clamp to midscale. 0 = clamp to ground. 1 = clamp to midscale. 0 = clamp to ground. 1 = clamp to midscale. 0 = don't clamp during coast. 1 = clamp during coast. 0 = internal clamp enabled. 1 = internal clamp disabled. 0 = low bandwidth. 1 = full bandwidth. 0 = normal auto-offset operation. 1 = hold current offset value. 0 = manual offset. 1 = auto-offset using offset as target code. 00 = every clamp. 01 = every 16 clamps. 10 = every 64 clamps. 11 = every VSYNC. 00 = 100% of difference used to calculate new offset. 01 = 50%. 10 = 25%. 11 = 12.5%. 0 = normal operation. 1 = if code > 15 codes off, offset is jumped to the predicted offset necessary to fix the > 15 code mismatch. 0 = disable post filer. 1 = enable post filter. Post filter reduces update rate by 1/6 and requires that all six updates recommend a change before changing the offset. This prevents unwanted offset changes. The toggle filter looks for the offset to toggle back and forth and holds it if triggered. This prevents toggling in case of missing codes in the PGA. Limits the amount the offset can change by in a single update. Number of clean HSYNCs required for sync filter to lock. Number of missing HSYNCs required to unlock the sync filter. Counter counts up if HSYNC pulse is missing and down for a good HSYNC. Width of the window in which HSYNC pulses are allowed. Enables coast, VSYNC duration, and VSYNC filter to use the regenerated HSYNC rather than the raw HSYNC. Rev. 0 | Page 25 of 60 AD9380 Hex Address Read/Write or Read-Only Bits [6] Default Value *1****** Register Name PLL Sync Filter Enable [5] **0***** VSYNC Filter Enable [4] ***0**** [3] **** 1*** VSYNC Duration Enable Auto-Offset Clamp Mode [2] **** *1** Auto-Offset Clamp Length 0x22 0x23 Read/Write Read/Write [7:0] [7:0] 4 32 VSYNC Duration HSYNC Duration 0x24 Read/Write [7] 1******* HSYNC Output Polarity [6] *1****** VSYNC Output Polarity 0x25 Read/Write [5] **1***** DE Output Polarity [4] ***1**** Field Output Polarity [3] ****1*** SOG Output Polarity [2:1] *****11* SOG Output Select [0] *******0 Output CLK Invert [7:6] 01****** Output CLK Select [5:4] **11**** [3:2] ****00** Output Drive Strength Output Mode Description Enables the PLL to use the filtered HSYNC rather than the raw HSYNC. This clips any bad HSYNCs, but does not regenerate missing pulses. Enables the VSYNC filter. The VSYNC filter gives a predictable HSYNC/VSYNC timing relationship but clips one HSYNC period off the leading edge of VSYNC. Enables the VSYNC duration block. This block can be used if necessary to restore the duration of a filtered VSYNC. 0 = auto-offset measures code during clamp. 1 = auto-offset measures code (10 or 16) clock cycles after end of clamp for 6 clock cycles. Sets delay after end of clamp for auto-offset clamp mode = 1. 0 = delay is 10 clock cycles. 1 = delay is 16 clock cycles. VSYNC duration. HSYNC duration. Sets the duration of the output HSYNC in pixel clocks. Output HSYNC polarity (both DVI and analog), 0 = active low out. 1 = active high out. Output VSYNC polarity (both DVI and analog). 0 = active low out. 1 = active high out. Output DE polarity (both DVI and analog) . 0 = active low out. 1 = active high out. Output field polarity (both DVI and analog). 0 = active low out. 1 = active high out. Output SOG polarity (analog only). 0 = active low out. 1 = active high out. Selects signal present on SOG output. 00 = SOG0 or SOG1. 01 = Raw HSYNC0 or Raw HSYNC1. 10 = regenerated sync. 11 = HSYNC to PLL. 0 = don't invert clock out. 1 = invert clock out. Select which clock to use on output pin. 1x CLK is divided down from TMDS clock input when pixel repetition is in use. 00 = 1/2x CLK. 01 = 1x CLK. 10 = 2x CLK. 11 = 90 phase 1x CLK. Set the drive strength of the outputs. 00 = lowest, 11 = highest. Selects which pins the data comes out on. 00 = 4:4:4 mode (normal). 01 = 4:2:2 + DDR 4:2:2 on blue. 10 = DDR 4:4:4 + DDR 4:2:2 on blue. 11 = 12-bit 4:2:2 (HDMI can have 12-bit 4:2:2 data). Rev. 0 | Page 26 of 60 AD9380 Hex Address 0x26 Read/Write or Read-Only Read/Write Bits [1] Default Value ******1* [0] *******0 [7] [6] [5] [4] [3] 0******* *0****** **0***** ***0**** ****1*** [2:1] *****00* Register Name Primary Output Enable Secondary Output Enable Output Three-State SOG Three-State SPDIF Three-State I2S Three-State Power-Down Pin Polarity Power-Down Pin Function [0] *******0 Power-Down [7] 1******* Auto Power-Down Enable [6] *0****** HDCP A0 [5] **0***** MCLK External Enable [4] ***0**** BT656 EN [3] [2:0] ****0*** *****000 Force DE Generation Interlace Offset Read/Write [7:2] 011000** VS Delay 0x29 Read/Write [1:0] [7:0] ******01 00000100 HS Delay MSB HS Delay 0x2A 0x2B 0x2C 0x2D 0x2E Read/Write Read/Write Read/Write Read/Write Read/Write [3:0] [7:0] [3:0] [7:0] [7] ****0101 00000000 ****0010 11010000 0******* Line Width MSB Line Width Screen Height MSB Screen Height Ctrl EN [6:5] *00***** I2S Out Mode [4:0] ***11000 I2S Bit Width 0x27 0x28 Read/Write Description Enables primary output. Enables secondary output (DDR 4:2:2 in Output Modes 1 and 2). Three-state the outputs. Three-state the SOG output. Three-state the SPDIF output. Three-state the I2S output and the MCLK out. Sets polarity of power-down pin. 0 = active low. 1 = active high. Selects the function of the power-down pin. 00 = power-down. 01 = power-down and three-state SOG. 10 = three-state outputs only. 11 = three-state outputs and SOG. 0 = normal. 1 = power-down. 0 = disable auto-low power state. 1 = enable auto-low power state. Sets the LSB of the address of the HDCP I2C. Set to 1 only for a second receiver in a dual-link configuration. 0 = use internally generated MCLK. 1 = use external MCLK input. If an external MCLK is used, then it must be locked to the video clock according to the CTS and N available in the I2C. Any mismatch between the internal MCLK and the input MCLK results in dropped or repeated audio samples. Enables EAV/SAV codes to be inserted into the video output data. Allows use of the internal DE generator in DVI mode. Sets the difference (in HSYNCs) in field length between Field 0 and Field 1. Sets the delay (in lines) from the VSYNC leading edge to the start of active video. MSB, Register 0x29. Sets the delay (in pixels) from the HSYNC leading edge to the start of active video. MSB, Register 0x2B. Sets the width of the active video line in pixels. MSB, Register 0x2D. Sets the height of the active screen in lines. Allows Ctrl [3:0] to be output on the I2S data pins. 00 = I2S mode. 01 = right-justified. 10 = left-justified. 11 = raw IEC60958 mode. Sets the desired bit width for right-justified mode. Rev. 0 | Page 27 of 60 AD9380 Hex Address 0x2F Read/Write or Read-Only Read 0x30 Read 0x31 0x32 0x33 0x34 Bits [6] [5] [4] [3] [2:0] [6] Default Value *0****** **0***** ***0**** ****0*** *****000 *0****** [5] [4] [3:0] **0***** ***0**** ****0000 DVI HSYNC Polarity DVI VSYNC Polarity HDMI Pixel Repetition [7:4] 1001**** MV Pulse Max [3:0] ****0110 MV Pulse Min Read/Write [7] 0******* MV Oversample En Read/Write [6] [5:0] [7] *0****** **001101 1******* MV Pal En MV Line Count Start MV Detect Mode [6] *0****** MV Settings Override [5:0] [7:6] **010101 10****** MV Line Count End MV Pulse Limit Set [5] **0***** Low Freq Mode [4] ***0**** Low Freq Override [3] ****0*** Up Conversion Mode [2] [1] *****0** ******0* CrCb Filter Enable CSC_Enable Read/Write Read/Write Register Name TMDS Sync Detect TMDS Active AV Mute HDCP Keys Read HDMI Quality HDMI Content Encrypted 0x35 Read/Write [6:5] *01* **** CSC_Mode 0x36 Read/Write [4:0] [7:0] ***01100 01010010 CSC_Coeff_A1 MSB CSC_Coeff_A1 LSB Description Detects a TMDS DE. Detects a TMDS clock. Gives the status of AV mute based on general control packets. Returns 1 when read of EEPROM keys is successful. Returns quality number based on DE edges. This bit is high when HDCP decryption is in use (content is protected). The signal goes low when HDCP is not being used. Customers can use this bit to determine whether or not to allow copying of the content. The bit should be sampled at regular intervals because it can change on a frame by frame basis. Returns DVI HSYNC polarity. Returns DVI VSYNC polarity. Returns current HDMI pixel repetition amount. 0 = 1x, 1 = 2x, ... The clock and data outputs automatically decimate by this value to present the data in the original form. Sets the maximum pseudo sync pulse width for Macrovision detection. Sets the minimum pseudo sync pulse width for Macrovision detection. Tells the Macrovision detection engine whether we are oversampling or not. Tells the Macrovision detection engine to enter PAL mode. Sets the start line for Macrovision detection. 0 = standard definition. 1 = progressive scan mode. 0 = use hard-coded settings for line counts and pulse widths. 1 = use I2C values for these settings. Sets the end line for Macrovision detection. Sets the number of pulses required in the last 3 lines (SD mode only). Sets audio PLL to low frequency mode. Low frequency mode should only be set for pixel clocks <80 MHz. Allows the previous bit to be used to set low frequency mode rather than the internal auto-detect. 0 = repeat Cr and Cb values. 1 = interpolate Cr and Cb values. Enables the FIR filter for 4:2:2 CrCb output. Enables the CSC. The default settings for the CSC provide HDTVto-RGB conversion. Sets the fixed point position of the CSC coefficients, including the A4, B4, and C4 offsets. 00 = 1.0, -4096 to +4095. 01 = 2.0, -8192 to +8190. 1x = 4.0, -16384 to +16380. MSB, Register 0x36. Color space converter (CSC) coefficient for equation: ROUT = (A1 x RIN) + (A2 x GIN) + (A3 x BIN) + A4 GOUT = (B1 x RIN) + (B2 x GIN) + (B3 x BIN) + B4 BOUT = (C1 x RIN) + (C2 x GIN) + (C3 x BIN) + C4 MSB, Register 0x38. CSC coefficient for equation: ROUT = (A1 x RIN + (A2 x GIN) + (A3 x BIN) + A4 GOUT = (B1 x RIN) + (B2 x GIN) + (B3 x BIN) + B4 BOUT = (C1 x RIN) + (C2 x GIN) + (C3 x BIN) + C4 B 0x37 0x38 Read/Write Read/Write [4:0] [7:0] ***01000 00000000 CSC_Coeff_A2 MSB CSC_Coeff_A2 LSB B Rev. 0 | Page 28 of 60 AD9380 Hex Address 0x39 0x3A Read/Write or Read-Only Read/Write Read/Write Bits [4:0] [7:0] Default Value ***00000 00000000 Register Name CSC_Coeff_A3 MSB CSC_Coeff_A3 LSB 0x3B 0x3C Read/Write Read/Write [4:0] [7:0] ***11001 11010111 CSC_Coeff_A4 MSB CSC_Coeff_A4 LSB 0x3D 0x3E Read/Write Read/Write [4:0] [7:0] ***11100 01010100 CSC_Coeff_B1 MSB CSC_Coeff_B1 LSB 0x3F 0x40 Read/Write Read/Write [4:0] [7:0] ***01000 00000000 CSC_Coeff_B2 MSB CSC_Coeff_B2 LSB 0x41 0x42 Read/Write Read/Write [4:0] [7:0] ***11110 10001001 CSC_Coeff_B3 MSB CSC_Coeff_B3 LSB 0x43 0x44 Read/Write Read/Write [4:0] [7:0] ***00010 10010010 CSC_Coeff_B4 MSB CSC_Coeff_B4 LSB 0x45 0x46 Read/Write Read/Write [4:0] [7:0] ***00000 00000000 CSC_Coeff_C1 MSB CSC_Coeff_C1 LSB 0x47 0x48 Read/Write Read/Write [4:0] [7:0] ***01000 00000000 CSC_Coeff_C2 MSB CSC_Coeff_C2 LSB 0x49 0x4A Read/Write Read/Write [4:0] [7:0] ***01110 10000111 CSC_Coeff_C3 MSB CSC_Coeff_C3 LSB 0x4B 0x4C Read/Write Read/Write [4:0] [7:0] ***11000 10111101 CSC_Coeff_C4 MSB CSC_Coeff_C4 LSB 0x50 Read/Write [7:0] 00100000 Test Description MSB, Register 0x3A. CSC coefficient for equation: ROUT = (A1 x RIN) + (A2 x GIN) + (A3 x BIN) + A4 GOUT = (B1 x RIN) + (B2 x GIN) + (B3 x BIN) + B4 BOUT = (C1 x RIN) + (C2 x GIN) + (C3 x BIN) + C4 MSB, Register 0x3C. CSC coefficient for equation: ROUT = (A1 x RIN) + (A2 x GIN) + (A3 x BIN) + A4 GOUT = (B1 x RIN) + (B2 x GIN) + (B3 x BIN) + B4 BOUT = (C1 x RIN) + (C2 x GIN) + (C3 x BIN) + C4 MSB, Register 0x3E. CSC coefficient for equation: ROUT = (A1 x RIN) + (A2 x GIN) + (A3 x BIN) + A4 GOUT = (B1 x RIN) + (B2 x GIN) + (B3 x BIN) + B4 BOUT = (C1 x RIN) + (C2 x GIN) + (C3 x BIN) + C4 MSB, Register 0x40. CSC coefficient for equation: ROUT = (A1 x RIN) + (A2 x GIN) + (A3 x BIN) + A4 GOUT = (B1 x RIN) + (B2 x GIN) + (B3 x BIN) + B4 BOUT = (C1 x RIN) + (C2 x GIN) + (C3 x BIN) + C4 MSB, Register 0x42. CSC coefficient for equation: ROUT = (A1 x RIN + (A2 x GIN) + (A3 x BIN) + A4 GOUT = (B1 x RIN) + (B2 x GIN) + (B3 x BIN) + B4 BOUT = (C1 x RIN) + (C2 x GIN) + (C3 x BIN) + C4 MSB, Register 0x44. CSC coefficient for equation: ROUT = (A1 x RIN) + (A2 x RIN) + (A3 x BIN) + A4 GOUT = (B1 x RIN) + (B2 x GIN) + (B3 x BIN) + B4 BOUT = (C1 x RIN) + (C2 x GIN) + (C3 x BIN) + C4 MSB, Register 0x46. CSC coefficient for equation: ROUT = (A1 x RIN) + (A2 x GIN) + (A3 x BIN) + A4 GOUT = (B1 x RIN) + (B2 x GIN) + (B3 x BIN) + B4 BOUT = (C1 x RIN) + (C2 x GIN) + (C3 x BIN) + C4 MSB, Register 0x48. CSC coefficient for equation: ROUT = (A1 x RIN) + (A2 x GIN) + (A3 x BIN) + A4 GOUT = (B1 x RIN) + (B2 x GIN) + (B3 x BIN) + B4 BOUT = (C1 x RIN) + (C2 x GIN) + (C3 x BIN) + C4 MSB, Register 0x4A. CSC coefficient for equation: ROUT = (A1 x RIN) + (A2 x GIN) + (A3 x BIN) + A4 GOUT = (B1 x RIN) + (B2 x GIN) + (B3 x BIN) + B4 BOUT = (C1 x RIN) + (C2 x GIN) + (C3 x BIN) + C4 MSB, Register 0x4C. CSC coefficient for equation: ROUT = (A1 x RIN) + (A2 x GIN) + (A3 x BIN) + A4 GOUT = (B1 x RIN) + (B2 x GIN) + (B3 x BIN) + B4 BOUT = (C1 x RIN) + (C2 x GIN) + (C3 x BIN) + C4 Must be written to 0x20 for proper operation. B B B B B B B B B B Rev. 0 | Page 29 of 60 AD9380 Hex Address 0x56 0x57 Read/Write or Read-Only Read/Write Read/Write 0x58 Read/Write Bits [7:0] [7] [6] [3] [2] [7] [6:4] Default Value 00001111 0******* *0****** ****0*** *****0** Register Name Test A/V Mute Override AV Mute Value Disable Video Mute Disable Audio Mute MCLK PLL Enable MCLK PLL_N [3] N_CTS_Disable [2:0] MCLK FS_N MDA/MCL PU CLK Term O/R Manual CLK Term FIFO Reset UF FIFO Reset OF MDA/MCL ThreeState Packet Detected 0x59 Read/Write [6] [5] [4] [2] [1] [0] 0x5A Read [6:0] 0x5B 0x5E Read Read [3] [7:6] [5:3] 2 1 0 0x5F Read [7:0] 0x60 Read 0x61 Read [7:4] [3:0] [5:4] [3:0] Description Must be written to 0x0F for proper operation. A1 overrides the AV mute value with Bit 6. Sets AV mute value if override is enabled. Disables mute of video during AV mute. Disables mute of audio during AV mute. MCLK PLL enable--uses analog PLL. MCLK PLL N [2:0]--this controls the division of the MCLK out of the PLL: 0 = /1, 1 = /2, 2 = /3, 3 = /4, etc. Prevents the N/CTS packet on the link from writing to the N and CTS registers. Controls the multiple of 128 fS used for MCLK out. 0 = 128 fS, 1 = 256 fS, 2 = 384, 7 = 1024 fS. This disables the MDA/MCL pull-ups. Clock termination power-down override: 0 = auto, 1 = manual. Clock termination: 0 = normal, 1 = disconnected. This bit resets the audio FIFO if underflow is detected. This bit resets the audio FIFO if overflow is detected. This bit three-states the MDA/MCL lines. These 7 bits are updated if any specific packet has been received since last reset or loss of clock detect. Normal is 0x00. Bit Data Packet Detected 0 AVI infoframe. 1 Audio infoframe. 2 SPD infoframe. 3 MPEG source infoframe. 4 ACP packets. 5 ISRC1 packets. 6 ISRC2 packets. HDMI Mode 0 = DVI, 1 = HDMI. Channel Status Mode = 00. All others are reserved. When Bit 1 = 0 (Linear PCM). 000 = 2 audio channels without pre-emphasis. 001 = 2 audio channels with 50/15 s pre-emphasis. 010 = reserved. 011 = reserved. 0 = software for which copyright is asserted. 1 = software for which no copyright is asserted. 0 = audio sample word represents linear PCM samples. 1 = audio sample word used for other purposes. 0 = consumer use of channel status block. Audio Channel Status See CEA 861B for description Channel Status Category Code Channel Number See CEA 861B for description Source Number Clock Accuracy Clock accuracy. 00 = Level II. 01 = Level III. 10 = Level I. 11 = reserved. Sampling 0011 = 2 kHz. Frequency 0000 = 44.1 kHz. 1000 = 88.2 kHz. Rev. 0 | Page 30 of 60 AD9380 Hex Address Read/Write or Read-Only Bits 0x62 Read [3:0] Word Length 0x7B Read [7:0] CTS [19:12] 0x7C 0x7D Read Read Read [7:0] [7:4] [3:0] CTS [11:4] CTS [3:0] N [19:16] 0x7E 0x7F Read Read [7:0] [7:0] N [15:8] N [7:0] 0x80 0x81 Read Read [7:0] [6:5] 4 [3:2] [1:0] 0x82 Read [7:6] [5:4] Default Value Register Name Description 1100 = 176.4 kHz. 0010 = 48k Hz. 1010 = 96 kHz. 1110 = 192 kHz. Word length. 0000 = not specified. 0100 = 16 bits. 0011 = 17 bits. 0010 = 18 bits. 0001 = 19 bits. 0101 = 20 bits. 1000 = not specified. 1100 = 20 bits. 1011 = 21 bits. 1010 = 22 bits. 1001 = 23 bits. 1101 = 24 bits. Cycle time stamp--this 20-bit value is used with the N value to regenerate an audio clock. For remaining bits, see Register 0x7C and Register 0x7D. See R0x7B. See R0x7B. 20-bit N used with CTS to regenerate the audio clock. For remaining bits, see Register 0x7E and Register 0x7F. AVI Infoframe AVI Infoframe Version Y [1:0] indicates RGB, 4:2:2 or 4:4:4. 00 = RGB. 01 = YCbCr 4:2:2. 10 = YCbCr 4:4:4. Active Format Active format information present. Information Status 0 = no data. 1 = active format information valid. Bar Information B [1:0]. 00 = no bar information. 01 = horizontal bar information valid. 10 = vertical bar information valid. 11 = horizontal and vertical bar information valid. Scan Information S [1:0]. 00 = no information. 01 = overscanned (television). 10 = underscanned (computer). Colorimetry C [1:0]. 00 = no data. 01 = SMPTE 170M, ITU601. 10 = ITU709. Picture Aspect Ratio M [1:0]. 00 = no data. 01 = 4:3. 10 = 16:9. Rev. 0 | Page 31 of 60 AD9380 Hex Address 0x83 Read/Write or Read-Only Read Bits [3:0] [1:0] Default Value Register Name Active Format Aspect Ratio Nonuniform Picture Scaling 0x84 Read [6:0] 0x85 Read [3:0] Video Identification Code Pixel Repeat 0x86 Read [7:0] Active Line Start LSB 0x87 Read [6:0] New Data Flags 0x88 0x89 Read Read [7:0] [7:0] Active Line Start MSB Active Line End LSB 0x8A 0x8B Read Read [7:0] [7:0] Active Line End MSB Active Pixel Start LSB 0x8C 0x8D Read Read [7:0] [7:0] Active Pixel Start MSB Active Pixel End LSB 0x8E 0x8F 0x90 Read Read Read [7:0] [6:0] [7:0] 0x91 Read [7:4] Active Pixel End MSB New Data Flags Audio Infoframe Version Audio Coding Type Description R [3:0]. 1000 = same as picture aspect ratio. 1001 = 4:3 (center). 1010 = 16:9 (center). 1011 = 14:9 (center). SC [1:0]. 00 = no known nonuniform scaling. 01 = picture has been scaled horizontally. 10 = picture has been scaled vertically. 11 = picture has been scaled horizontally and vertically. VIC [6:0] video identification code--refer to CEA EDID short video descriptors. PR [3:0]--This specifies how many times a pixel has been repeated. 0000 = no repetition (pixel sent once). 0001 = pixel sent twice (repeated once). 0010 = pixel sent 3 times. 1001 = pixel sent 10 times. Values 0xA to 0xF reserved. This represents the line number of the end of the top horizontal bar. If 0, there is no horizontal bar. Combines with Register 0x88 for a 16-bit value. New data flags. These 7 bits are updated if any specific data changes. Normal (no NDFs) is 0x00. When any NDF register is read, all bits reset to 0x00. All NDF registers contain the same data. Bit Data Packet Changed 0 AVI infoframe. 1 audio infoframe. 2 SPD infoframe. 3 MPEG source infoframe. 4 ACP packets. 5 ISRC1 packets. 6 ISRC2 packets. Active line start MSB (see Register 0x86). This represents the line number of the beginning of a lower horizontal bar. If greater than the number of active video lines, there is no lower horizontal bar. Combines with Register 0x8A for a 16-bit value. Active line end MSB. See Register 0x89. This represents the last pixel in a vertical pillar-bar at the left side of the picture. If 0, there is no left bar. Combines with Register 0x8C for a 16-bit value. Active pixel start MSB. See Register 0x8B. This represents the first horizontal pixel in a vertical pillar bar at the right side of the picture. If greater than the maximum number of horizontal pixels, there is no vertical bar. Combines with Register 0x8E for a16-bit value. Active pixel end MSB. See Register 0x8D. New data flags (see Register 0x87). CT [3:0]. Audio coding type. Rev. 0 | Page 32 of 60 AD9380 Hex Address Read/Write or Read-Only Bits [2:0] 0x92 Read [4:2] [1:0] 0x93 Read [7:0] 0x94 Read [7:0] 0x95 7 Read [6:3] 0x96 0x97 Read Read [7:0] [6:0] 0x98 Read [7:0] 0x99 Read [7:0] 0x9A 0x9B 0x9C 0x9D Read Read Read Read [7:0] [7:0] [7:0] [7:0] Default Value Register Name Description 0x0 = Refer to stream header. 0x1 = IEC60958 PCM. 0x2 = AC3. 0x3 = MPEG1 (Layer 1 and Layer 2). 0x4 = MP3 (MPEG1 Layer 3). 0x5 = MPEG2 (multichannel). 0x6 = AAC. 0x7 = DTS. 0x8 = ATRAC. Audio Coding Count CC [2:0]. Audio channel count. 000 = refer to stream header. 001 = 2 channels. 010 = 3 channels. 111 = 8 channels. Sampling Frequency SF [2:0]. Sampling frequency. 000 = refer to stream header. 001 = 32 kHz. 010 = 44.1 kHz (CD). 011 = 48 kHz. 100 = 88.2 kHz. 101 = 96 kHz. 110 = 176.4 kHz. 111 = 192 kHz. Sample Size SS [1:0]. Sample size. 00 = refer to stream header. 01 = 16-bit. 10 = 20-bit. 11 = 24-bit. Max Bit Rate Max bit rate (compressed audio only). The value of this field multiplied by 8 kHz represents the maximum bit rate. Speaker Mapping CA [7:0]. Speaker mapping or placement for up to 8 channels. See Table 39. Down-Mix DM_INH--down-mix inhibit. 0 = permitted or no information. 1 = prohibited. Level Shift LSV [3:0]--level shift values with attenuation information. 0000 = 0 dB attenuation. 0001 = 1 dB attenuation. ..... 1111 = 5 dB attenuation. Reserved. New Data Flags New data flags (see Register 0x87). Source Product Description (SPD) Infoframe See CEA 861B for description. Source Product Description (SPD) Infoframe Version Vender Name Vender name character 1 (VN1) in 7-bit ASCII code. This is the Character 1 first character in 8 of the company name that appears on the product. VN2 VN2. VN3 VN3. VN4 VN4. VN5 VN5. Rev. 0 | Page 33 of 60 AD9380 Hex Address 0x9E 0x9F 0xA0 0xA1 0xA2 Read/Write or Read-Only Read Read Read Read Read Bits [7:0] [6:0] [7:0] [7:0] [7:0] 0xA3 0xA4 0xA5 0xA6 0xA7 0xA8 0xA9 0xAA 0xAB 0xAC 0xAD 0xAE 0xAF 0xB0 0xB1 0xB2 0xB3 0xB4 Read Read Read Read Read Read Read Read Read Read Read Read Read Read Read Read Read Read [7:0] [7:0] [7:0] [7:0] [7:0] [6:0] [7:0] [7:0] [7:0] [7:0] [7:0] [7:0] [6:0] [7:0] [7:0] [7:0] [7:0] [7:0] 0xB7 Read [6:0] 0xB8 Read [7:0] 0xB9 Read [7:0] 0xBA 0xBB 0xBC Read Read Read [7:0] [7:0] [7:0] 4 0xBD Read [1:0] Default Value Register Name VN6 New Data Flags VN7 VN8 Product Description Character 1 Description VN6. New data flags (see 0x87). VN7. VN8. Product Description Character 1 (PD1) in 7-bit ASCII code. This is the first character of 16 that contains the model number and a short description. PD2 PD2. PD3 PD3. PD4 PD4. PD5 PD5. New Data Flags New data flags (see Register 0x87). PD6 PD6. PD7 PD7. PD8 PD8. PD9 PD9. PD10 PD10. PD11 PD11. PD12 PD12. New Data Flags New data flags (see Register 0x87). PD13 PD13. PD14 PD14. PD15 PD15. PD16 PD16. Source Device This is a code that classifies the source device. Information Code 0x00 = unknown. 0x01 = digital STB. 0x02 = DVD. 0x03 = D-VHS. 0x04 = HDD video. 0x05 = DVC. 0x06 = DSC. 0x07 = video CD. 0x08 = game. 0x09 = PC general. New Data Flags New data flags (see Register 0x87). MPEG Source Infoframe See CEA 861B for description. MPEG Source Infoframe Version MB(0) MB [0] Lower byte of MPEG bit rate: Hz. This is the lower 8 bits of 32 bits (4 bytes) that specify the MPEG bit rate in Hz. MB[1] MB [1]. MB[2] MB [2]. MB [3] (upper byte). Field Repeat FR--New field or repeated field. 0 = New field or picture. 1 = Repeated field. MPEG Frame MF [1:0]. This identifies whether frame is an I, B, or P picture. 00 = unknown. 01 = I picture. 10 = B picture. 11 = P picture. Rev. 0 | Page 34 of 60 AD9380 Hex Address 0xBE 0xBF 0xC0 Read/Write or Read-Only Read Read Read 0xC1 0xC2 0xC3 0xC4 0xC5 0xC6 0xC7 0xC8 Read Read Read Read Rea Read Read [7:0] [7:0] [7:0] [7:0] [7:0] [7:0] [6:0] 7 ACP Packet Byte 0 ACP_PB1 ACP_PB2 ACP_PB3 ACP_PB4 ACP_PB5 NDF ISRC1 Continued Read 6 ISRC1 Valid [2:0] ISRC1 Status Bits [7:0] [6:0] [7:0] Default Value Register Name New Data Flags Audio Content Protection Packet (ACP) Type 0xC9 0xCA 0xCB 0xCC 0xCD 0xCE 0xCF 0xD0 0xD1 0xD2 0xD3 0xD4 0xD5 0xD6 0xD7 0xD8 0xD9 0xDA 0xDB 0xDC Read Read Read Read Read Read Read Read Read Read Read Read Read Read Read Read Read Read Read Read [7:0] [7:0] [7:0] [7:0] [7:0] [7:0] [6:0] [7:0] [7:0] [7:0] [7:0] [7:0] [7:0] [7:0] [6:0] [7:0] [7:0] [7:0] [7:0] [7:0] ISRC1 Packet Byte 0 ISRC1_PB1 ISRC1_PB2 ISRC1_PB3 ISRC1_PB4 ISRC1_PB5 NDF ISRC1_PB6 ISRC1_PB7 ISRC1_PB8 ISRC1_PB9 ISRC1_PB10 ISRC1_PB11 ISRC1_PB12 NDF ISRC1_PB13 ISRC1_PB14 ISRC1_PB15 ISRC1_PB16 ISRC2 Packet Byte 0 0xDD 0xDE 0xDF 0xE0 0xE1 0xE2 0xE3 0xE4 Read Read Read Read Read Read Read Read [7:0] [7:0] [6:0] [7:0] [7:0] [7:0] [7:0] [7:0] ISRC2_PB1 ISRC2_PB2 New Data Flags ISRC2_PB3 ISRC2_PB4 ISRC2_PB5 ISRC2_PB6 ISRC2_PB7 Description Reserved. New data flags (see 0x87). Audio content protection packet (ACP) type. 0x00 = Generic audio. 0x01 = IEC 60958-identified audio. 0x02 = DVD-audio. 0x03 = reserved for super audio CD (SACD). 0x04 to 0xFF reserved. ACP Packet Byte 0 (ACP_PB0). ACP_PB1. ACP_PB2. ACP_PB3. ACP_PB4. ACP_PB5. New data flags (see 0x87). International standard recording code (ISRC1) continued--This indicates an ISRC2 packet is being transmitted. 0 = ISRC1 status bits and packet bytes (PBs) not valid. 1 = ISRC1 status bits and PBs valid. 001 = starting position. 010 = intermediate position. 100 = final position. ISRC1 Packet Byte 0 (ISRC1_PB0). ISRC1_PB1. ISRC1_PB2. ISRC1_PB3. ISRC1_PB4. ISRC1_PB5. New data flags (see Register 0x87). ISRC1_PB6. ISRC1_PB7. ISRC1_PB8. ISRC1_PB9. ISRC1_PB10. ISRC1_PB11. ISRC1_PB12. New data flags (see 0x87). ISRC1_PB13. ISRC1_PB14. ISRC1_PB15. ISRC1_PB16. ISRC2 Packet Byte 0 (ISRC2_PB0)--This is transmitted only when the ISRC continue bit (Register 0xC8, Bit 7) is set to 1. ISRC2_PB1. ISRC2_PB2. New data flags (see Register 0x87). ISRC2_PB3. ISRC2_PB4. ISRC2_PB5. ISRC2_PB6. ISRC2_PB7. Rev. 0 | Page 35 of 60 AD9380 Hex Address 0xE5 0xE6 0xE7 0xE8 0xE9 0xEA 0xEB 0xEC 0xED 0xEE Read/Write or Read-Only Read Read Read Read Read Read Read Read Read Read Bits [7:0] [7:0] [6:0] [7:0] [7:0] [7:0] [7:0] [7:0] [7:0] [7:0] Default Value Register Name ISRC2_PB8 ISRC2_PB9 New Data Flags ISRC2_PB10 ISRC2_PB11 ISRC2_PB12 ISRC2_PB13 ISRC2_PB14 ISRC2_PB15 ISRC2_PB16 Description ISRC2_PB8. ISRC2_PB9. New data flags (see Register 0x87). ISRC2_PB10. ISRC2_PB11. ISRC2_PB12. ISRC2_PB13. ISRC2_PB14. ISRC2_PB15. ISRC2_PB16. Rev. 0 | Page 36 of 60 AD9380 2-WIRE SERIAL CONTROL REGISTER DETAILS CHIP IDENTIFICATION CLOCK GENERATOR CONTROL 0x00--Bits[7:0] Chip Revision 0x03--Bits[7:6] VCO Range Select An 8-bit value that reflects the current chip revision. Two bits that establish the operating range of the clock generator. VCORNGE must be set to correspond with the desired operating frequency (incoming pixel rate). The PLL gives the best jitter performance at high frequencies. For this reason, to output low pixel rates and still get good jitter performance, the PLL actually operates at a higher frequency but then divides down the clock rate. Table 13 shows the pixel rates for each VCO range setting. The PLL output divisor is automatically selected with the VCO range setting. PLL DIVIDER CONTROL 0x01--Bits[7:0] PLL Divide Ratio MSBs The eight most significant bits of the 12-bit PLL divide ratio PLLDIV. The PLL derives a pixel clock from the incoming HSYNC signal. The pixel clock frequency is then divided by an integer value, such that the output is phase-locked to HSYNC. This PLLDIV value determines the number of pixel times (pixels plus horizontal blanking overhead) per line. This is typically 20% to 30% more than the number of active pixels in the display. The 12-bit value of the PLL divider supports divide ratios from 221 to 4095. The higher the value loaded in this register, the higher the resulting clock frequency with respect to a fixed HSYNC frequency. VESA has established some standard timing specifications, which assist in determining the value for PLLDIV as a function of horizontal and vertical display resolution and frame rate (see Table 9). However, many computer systems do not conform precisely to the recommendations, and these numbers should be used only as a guide. The display system manufacturer should provide automatic or manual means for optimizing PLLDIV. An incorrectly set PLLDIV usually produces one or more vertical noise bars on the display. The greater the error, the greater the number of bars produced. Table 13. VCO Ranges VCO Range 00 01 10 11 Pixel Rate Range 12 to 30 30 to 60 60 to 120 120 to 150 The power-up default value is 01. Bits[5:3] Charge Pump Current Three bits that establish the current driving the loop filter in the clock generator. Table 14. Charge Pump Currents Ip2 0 0 0 0 1 1 1 1 Ip1 0 0 1 1 0 0 1 1 Ip0 0 1 0 1 0 1 0 1 Current (A) 50 100 150 250 350 500 750 1500 The power-up default value of PLLDIV is 1693 (PLLDIVM = 0x69, PLLDIVL = 0xDx) The power-up default value is current = 001. The AD9380 updates the full divide ratio only when the LSBs are changed. Writing to this register by itself does not trigger an update. This bit determines the source of the pixel clock. 0x02--Bits[7:4] PLL Divide Ratio LSBs The four least significant bits of the 12-bit PLL divide ratio PLLDIV. The power-up default value of PLLDIV is 1693 (PLLDIVM = 0x69, PLLDIVL = 0xDx). Bit[2] External Clock Enable Table 15. External Clock Select Settings EXTCLK 0 1 Function Internally generated clock Externally provided clock signal A Logic 0 enables the internal PLL that generates the pixel clock from an externally provided HSYNC. A Logic 1 enables the external CKEXT input pin. In this mode, the PLL divide ratio (PLLDIV) is ignored. The clock phase adjusts (phase is still functional). The power-up default value is EXTCLK = 0. Rev. 0 | Page 37 of 60 AD9380 0x04--Bits[7:3] Phase Adjust These bits provide a phase adjustment for the DLL to generate the ADC clock. A 5-bit value that adjusts the sampling phase in 32 steps across one pixel time. Each step represents an 11.25 shift in sampling phase. The power-up default is 16. INPUT GAIN 0x05--Bits[7:0] Red Channel Gain If clamp feedback is disabled, the offset register bits control the absolute offset added to the channel. The offset control provides a +127/-128 LSBs of adjustment range, with one LSB of offset corresponding to 1 LSB of output code. If clamp feedback is enabled these bits provide the relative offset (brightness) from the offset adjust in the previous register. The power-up default is 0x80. 0x0A--Bits[7:0] Green Channel Offset Adjust These bits control the programmable gain amplifier (PGA) of the red channel. The AD9380 can accommodate input signals with a full-scale range of between 0.5 V and 1.0 V p-p. Setting the red gain to 255 corresponds to an input range of 1.0 V. A red gain of 0 establishes an input range of 0.5 V. Note that increasing red gain results in the picture having less contrast (the input signal uses fewer of the available converter codes). The power-up default is 0x80. 0x06--Bits[7:0] Green Channel Gain If clamp feedback is enabled, the 8-bit offset adjust determines the clamp code. The 8-bit offset adjust is a twos complement number consisting of 1 sign bit plus 7 bits (0x7F = +127, 0x00 = 0, 0xFF = -1, and 0x80 = -128). For example, if the register is programmed to 130d, then the output code is equal to 130d at the end of the clamp period. Note that incrementing the offset register setting by 1 LSB adds 1 LSB of offset, regardless of the clamp feedback setting. The power-up default is 0. 0x0B--Bits[7-0] Green Channel Offset These bits control the PGA of the green channel. The AD9380 can accommodate input signals with a full-scale range of between 0.5 V p-p and 1.0 V p-p. Setting the green gain to 255 corresponds to an input range of 1.0 V. A green gain of 0 establishes an input range of 0.5 V. Note that increasing green gain results in the picture having less contrast (the input signal uses fewer of the available converter codes). The power-up default is 0x80. 0x07--Bits[7:0] Blue Channel Gain These bits control the PGA of the blue channel. The AD9380 can accommodate input signals with a full-scale range of between 0.5 V and 1.0 V p-p. Setting the blue gain to 255 corresponds to an input range of 1.0 V. A blue gain of 0 establishes an input range of 0.5 V. Note that increasing blue gain results in the picture having less contrast (the input signal uses fewer of the available converter codes). The power-up default is 0x80. INPUT OFFSET 0x08--Bits[7:0] Red Channel Offset Adjust If clamp feedback is enabled, the 8-bit offset adjust determines the clamp code. The 8-bit offset adjust is a twos complement number consisting of 1 sign bit plus 7 bits (0x7F = +127, 0x00 = 0, 0xFF = -1, and 0x80 = -128). For example, if the register is programmed to 130d, then the output code is equal to 130d at the end of the clamp period. Note that incrementing the offset register setting by 1 LSB adds 1 LSB of offset, regardless of the clamp feedback setting. The power-up default is 0. 0x09--Bits[7:0] Red Channel Offset These eight bits are the red channel offset control. The offset control shifts the analog input, resulting in a change in brightness. Note that the function of the offset register depends on whether clamp feedback is enabled (Register 0x1C, Bit 7 = 1). These eight bits are the green channel offset control. The offset control shifts the analog input, resulting in a change in brightness. Note that the function of the offset register depends on whether clamp feedback is enabled (Register 0x1C, Bit 7 = 1). If clamp feedback is disabled, the offset register bits control the absolute offset added to the channel. The offset control provides an adjustment range of +127/-128 LSBs, with one LSB of offset corresponding to 1 LSB of output code. If clamp feedback is enabled, these bits provide the relative offset (brightness) from the offset adjust in the previous register. The power-up default is 0x80. 0x0C--Bits[7:0] Blue Channel Offset Adjust If clamp feedback is enabled, the 8-bit offset adjust determines the clamp code. The 8-bit offset adjust is a twos complement number consisting of 1 sign bit plus 7 bits (0x7F = +127, 0x00 = 0, 0xFF = -1, and 0x80 = -128). For example, if the register is programmed to 130d, then the output code is equal to 130d at the end of the clamp period. Note that incrementing the offset register setting by 1 LSB adds 1 LSB of offset, regardless of the clamp feedback setting. The power-up default is 0. 0x0D--Bits[7:0] Blue Channel Offset These eight bits are the blue channel offset control. The offset control shifts the analog input, resulting in a change in brightness. Note that the function of the offset register depends on whether clamp feedback is enabled (Register 0x1C, Bit 7 = 1). If clamp feedback is disabled, the offset register bits control the absolute offset added to the channel. The offset control provides an adjustment range of +127/-128 LSBs, with 1 LSB of offset corresponding to 1 LSB of output code. If clamp feedback is enabled, these bits provide the relative offset (brightness) from the offset adjust in the previous register. The power-up default is 0x80. Rev. 0 | Page 38 of 60 AD9380 SYNC 0x12--Bits[6] HSYNC Polarity Override 0x0E--Bits[7:0] Sync Separator Selects the maximum HSYNC pulse width for composite sync separation. Power-down default is 0x20. 0 = auto HSYNC polarity, 1 = manual HSYNC polarity. Manual HSYNC polarity is defined in Register 0x11, Bit 7. The powerup default is 0. 0x0F--Bits[7:2] SOG Comparator Threshold Enter 0x12--Bit[5] Input VSYNC Polarity The enter level for the SOG slicer. Must be < exit level (Register 0x10). The power-up default is 0x10. 0 = active low, 1 = active high. The power-up default is 1. These selections are ignored if Register 0x11, Bit 4 = 0. 0x10--Bits[7:2] SOG Comparator Threshold Exit 0x12--Bit[4] VSYNC Polarity Override The exit level for the SOG slicer. Must be > enter level (Register 0x0F). The power-up default is 0x10. 0 = auto VSYNC polarity, 1 = manual VSYNC polarity. Manual VSYNC polarity is defined in Register 0x11, Bit 5. The powerup default is 0. 0x11--Bit[7] HSYNC Source COAST AND CLAMP CONTROLS 0 = HSYNC, 1 = SOG. The power-up default is 0. These selections are ignored if Register 0x11, Bit 6 = 0. 0x12--Bit[3] Input Coast Polarity 0 = active low, 1 = active high. The power-up default is 1. 0x11--Bit[6] HSYNC Source Override 0 = auto HSYNC source, 1 = manual HSYNC source. Manual HSYNC source is defined in Register 0x11, Bit 7. The power-up default is 0. 0x12--Bit[2] Coast Polarity Override 0x11--Bit[5] VSYNC Source 0x12--Bit[1] Coast Source 0 = VSYNC, 1 = VSYNC from SOG. The power-up default is 0. These selections are ignored if Register 0x11, Bit 4 = 0. 0 = internal coast, 1 = external coast. The power-up default is 0. 0x11--Bit[4] VSYNC Source Override 0 = use raw VSYNC for coast generation, 1 = use filtered VSYNC for coast generation The power-up default is 1. 0 = auto VSYNC source, 1 = manual VSYNC source. Manual VSYNC source is defined in Register 0x11, Bit 5. The power-up default is 0. 0x11--Bits[3] Channel Select 0 = Channel 0, 1 = Channel 1. The power-up default is 0. These selections are ignored if Register 0x11, Bit 2 = 0. 0x11--Bit[2] Channel Select Override 0 = auto channel select, 1 = manual channel select. Manual channel select is defined in Register 0x11, Bit 3. The power-up default is 0. 0x11--Bits[1] Interface Select 0 = analog interface, 1 = digital interface. The power-up default is 0. These selections are ignored if Register 0x11, Bit 0 = 0. 0x11--Bit[0] Interface Select Override 0 = auto interface select, 1 = manual interface select. Manual interface select is defined in Register 0x11, Bit 1. The power-up default is 0. 0 = auto-coast polarity, 1 = manual coast polarity. The powerup default is 0. 0x12--Bit[0] Filter Coast VSYNC 0x13--Bits[7:0] Precoast This register allows the internally generated coast signal to be applied prior to the VSYNC signal. This is necessary in cases where pre-equalization pulses are present. The step size for this control is one HSYNC period. For precoast to work correctly, it is necessary for both the VSYNC filter (0x21, Bit 5) and sync processing filter (0x21 Bit 7) to be either enabled or disabled. The power-up default is 0. 0x14--Bits[7:0] Postcoast This register allows the internally generated coast signal to be applied following the VSYNC signal. This is necessary in cases where post-equalization pulses are present. The step size for this control is one HSYNC period. For postcoast to work correctly, it is necessary for both the VSYNC filter (0x21, Bit 5) and sync processing filter (0x21, Bit 7) to be either enabled or disabled. The power-up default is 0. STATUS OF DETECTED SIGNALS 0x15--Bit[7] HSYNC 0 Detection Bit 0x12--Bit[7] Input HSYNC Polarity 0 = active low, 1 = active high. The power-up default is 1. These selections are ignored if Register 10x2, Bit 6 = 0. This bit is used to indicate when activity is detected on the HSYNC 0 input pin. If HSYNC is held high or low, activity is not detected. The sync processing block diagram shows where this function is implemented. 0 = HSYNC 0 not active. 1 = HSYNC 0 is active. Rev. 0 | Page 39 of 60 AD9380 0x15--Bit[6] HSYNC 1 Detection Bit 0x16--Bit[3] Coast Polarity This bit is used to indicate when activity is detected on the HSYNC 1 input pin. If HSYNC is held high or low, activity is not detected. The sync processing block diagram shows where this function is implemented. 0 = HSYNC 1 not active. 1 = HSYNC 1 is active. Indicates the polarity of the external coast signal. 0 = coast polarity negative. 1 = coast polarity positive. 0x15--Bit[5] VSYNC 0 Detection Bit This bit is used to indicate when activity is detected on the VSYNC0 input pin. If VSYNC is held high or low, activity is not detected. Figure 8 shows where this function is implemented. 0 = VSYNC 0 not active. 1 = VSYNC 0 is active. 0x16--Bit[2] Pseudo Sync Detected This bit indicates that a pulse other than an expected HSYNC has occurred. 0x16--Bits[1] Sync Filter Locked Indicates whether sync filter is locked to periodic sync signals. 0 = sync filter locked to periodic sync signal. 1 = sync filter not locked. 0x15--Bit[4] VSYNC 1 Detection Bit 0x16--Bit[0] Bad Sync Detect This bit is used to indicate when activity is detected on the VSYNC1 input pin. If VSYNC is held high or low, activity is not detected. Figure 8 shows where this function is implemented. 0 = VSYNC1 not active. 1 = VSYNC1 is active. This bit indicates when an HSYNC has occurred outside the filter window. 0x15--Bit[3] SOG 0 Detection Bit This bit is used to indicate when activity is detected on the SOG 0 input pin. If SOG is held high or low, activity is not detected. Figure 8 shows where this function is implemented. 0 = SOG 0 not active. 1 = SOG0 is active. 0x15--Bit[2] SOG 1 Detection Bit Indicates if SOG 1 is active. This bit is used to indicate when activity is detected on the SOG 1 input pin. If SOG is held high or low, activity is not detected. Figure 8 shows where this function is implemented. 0 = SOG 1 not active. 1 = SOG 1 is active. 0x15--Bit[1] Coast Detection Bit This bit detects activity on the EXTCLK/COAST pin. It indicates that one of the two signals is active, but it doesn't indicate if it is EXTCLK or COAST. A dc signal is not detected. 0 = no activity detected. 1 = activity detected. POLARITY STATUS 0x16--Bit[7] HSYNC 0 Polarity Indicates the polarity of the HSYNC0 input. 0 = HSYNC polarity negative. 1 = HSYNC polarity positive. 0x16--Bit[6] HSYNC 1 Polarity Indicates the polarity of the HSYNC1 input. 0 = HSYNC polarity negative. 1 = HSYNC polarity positive. 0x16--Bit[5] VSYNC 0 Polarity Indicates the polarity of the VSYNC0 input. 0 = VSYNC polarity negative. 1 = VSYNC polarity positive. 0x16--Bit[4] VSYNC 1 Polarity Indicates the polarity of the VSYNC1 input. 0 = VSYNC polarity negative. 1 = VSYNC polarity positive. 0x17--Bits[3:0] HSYNCs per VSYNC MSBs The 4 MSBs of the 12-bit counter that reports the number of HSYNCs/VSYNC on the active input. This is useful in determining the mode and an aid in setting the PLL divide ratio. 0x18--Bits[7:0] HSYNCs per VSYNC LSBs The 8 LSBs of the 12-bit counter that reports the number of HSYNCs/VSYNC on the active input. 0x19--Bits[7:0] Clamp Placement Number of pixel clocks after trailing edge of HSYNC to begin clamp. The power-up default is 8. 0x1A--Bits[7:0] Clamp Duration Number of pixel clocks to clamp. The power-up default is 0x14. 0x1B--Bit[7] Red Clamp Select This bit selects whether the red channel is clamped to ground or midscale. Ground clamping is used for red in RGB applications and midscale clamping is used in YPrPb (YUV) applications. 0 = channel clamped to ground during clamping period. 1 = channel clamped to midscale during clamping period. The power-up default is 0. 0x1B--Bit[6] Green Clamp Select This bit selects whether the green channel is clamped to ground or midscale. Ground clamping is normally used for green in RGB applications and YPrPb (YUV) applications. 0 = channel clamped to ground during clamping period. 1 = channel clamped to midscale during clamping period. The power-up default is 0. 0x1B--Bit[5] Blue Clamp Select This bit selects whether the blue channel is clamped to ground or midscale. Ground clamping is used for blue in RGB applications and midscale clamping is used in YPrPb (YUV) applications. 0 = channel clamped to ground during clamping period. 1 = channel clamped to midscale during clamping period. The power-up default is 0. Rev. 0 | Page 40 of 60 AD9380 0x1B--Bit[4] Clamp During Coast 0x1D--Bits[7:0] Slew Limit This bit permits clamping to be disabled during coast because video signals are generally not at a known back porch or midscale position during coast. 0 = clamping during coast is disabled. 1 = clamping during coast is enabled. Limits the amount the offset can change by in a single update. The power-up default is 0x08. 0x1E--Bits[7:0] Sync Filter Lock Threshold This 8-bit register is programmed to set the number of valid HSYNCs needed to lock the sync filter. This ensures that a consistent, stable HSYNC is present before attempting to filter. The power-up default setting is 32d. The power-up default is 0. 0x1B--Bit[3] Clamp Disable 0 = internal clamp enabled. 1 = internal clamp disabled. The power-up default is 0. 0x1F--Bits[7:0] Sync Filter Unlock Threshold x0 = low bandwidth. x1 = high bandwidth. The power-up default is 1. This 8-bit register is programmed to set the number of missing or invalid HSYNCs needed to unlock the sync filter. This disables the filter operation when there is no longer a stable HSYNC signal. The power-up default setting is 50d. 0x1B--Bit[0] Hold Auto-Offset 0x20--Bits[7:0] Sync Filter Window Width 0 = normal auto-offset operation. 1 = hold current offset value. The power-up default is 0. This 8-bit register sets the distance in 40 MHz clock periods (25 ns), which is the allowed distance for HSYNC pulses before and after the expected HSYNC edge. This is the heart of the filter in that it only looks for HSYNC pulses at a given time (plus or minus this window) and then ignores extraneous equalization pulses that disrupt accurate PLL operation. The power-up default setting is 10d, or 200 ns on either side of the expected HSYNC. 0x1B--Bit[2:1] Programmable Bandwidth 0x1C--Bit[7] Auto-Offset Enable 0 = manual offset. 1 = auto-offset using offset as target code. The power-up default is 0. 0x1C--Bits[6:5] Auto-Offset Update Mode 00 = every clamp. 01 = every 16 clamps. 10 = every 64 clamps. 11 = every VSYNC. The power-up default setting is 10. 0x21--Bit[7] Sync Processing Filter Enable This bit selects which HSYNC is used for the sync processing functions of internal coast, H/V count, field detection, and VSYNC duration counts. A clean HSYNC is fundamental to accurate processing of the sync. 0 = sync processing uses raw HSYNC or SOG. 1 = sync processing uses regenerated HSYNC from sync filter. The power-up default setting is 1. 0x1C--Bits[4:3] Difference Shift Amount 00 = 100% of difference used to calculate new offset. 01 = 50%. 10 = 25%. 11 = 12.5%. The power-up default is 01. 0x21--Bit[6] PLL Sync Filter Enable 0 = normal operation. 1 = if the code >15 codes off, the offset is jumped to the predicted offset necessary to fix the >15 code mismatch. The power-up default is 1. This bit selects which signal the PLL uses. It can select between raw HSYNC or SOG, or filtered versions. The filtering of the HSYNC and SOG can eliminate nearly all extraneous transitions which have traditionally caused PLL disruption. 0 = PLL uses raw HSYNC or SOG inputs. 1 = PLL uses filtered HSYNC or SOG inputs. The power-up default setting is 0. 0x1C--Bits[1] Post Filter Enable 0x21--Bit[5] VSYNC Filter Enable The post filter reduces the update rate by 1/6 and requires that all six updates recommend a change before changing the offset. This prevents unwanted offset changes. 0 = disable post filter. 1 = enable post filter. The power-up default is 1. The purpose of the VSYNC filter is to guarantee the position of the VSYNC edge with respect to the HSYNC edge and to generate a field signal. The filter works by examining the placement of VSYNC and regenerating a correctly placed VSYNC one line later. The VSYNC is first checked to see whether it occurs in the Field 0 position or the Field 1 position. This is done by checking the leading edge position against the sync separator threshold and the HSYNC position. The HSYNC width is divided into four quadrants with Quadrant 1 starting at the HSYNC leading edge plus a sync separator threshold. If the VSYNC leading edge occurs in Quadrant 1 or Quadrant 4, the field is set to 0 and the output VSYNC is placed coincident with 0x1C--Bit[2] Auto-Jump Enable 0x1C--Bit[0] Toggle Filter Enable The toggle filter looks for the offset to toggle back and forth and holds it if triggered. This is to prevent toggling in case of missing codes in the PGA. 1 = toggle filter on, and 0 = toggle filter off. The power-up default is 0. Rev. 0 | Page 41 of 60 AD9380 the HSYNC leading edge. If the VSYNC leading edge occurs in Quadrant 2 or Quadrant 3, the field is set to 1 and the output VSYNC leading edge is placed in the center of the line. In this way, the VSYNC filter creates a predictable relative position between HSYNC and VSYNC edges at the output. 0x24--Bit[6] VSYNC Output Polarity If the VSYNC occurs near the HSYNC edge, this guarantees that the VSYNC edge follows the HSYNC edge. This performs filtering also in that it requires a minimum of 64 lines between VSYNCs. The VSYNC filter cleans up extraneous pulses that might occur on the VSYNC. This should be enabled whenever the HSYNC/VSYNC count is used. Setting this bit to 0 disables the VSYNC filter. Setting this bit to 1 enables the VSYNC filter. Power-up default is 0. 0x24--Bit[5] Display Enable Output Polarity 0x21--Bit[4] VSYNC Duration Enable This enables the VSYNC duration block which is designed to be used with the VSYNC filter. 0 = leave the VSYNC output duration unchanged. 1 = set the VSYNC output duration based on Register 0x22. The power-up default is 0. This bit sets the polarity of the VSYNC output (both DVI and analog). Setting this bit to 0 sets the VSYNC output to active low. Setting this bit to 1 sets the VSYNC output to active high. Power-up default is 1. This bit sets the polarity of the display enable (DE) for both DVI and analog. 0 = DE output polarity is negative. 1 = DE output polarity is positive. The power-up default is 1. 0x24--Bit[4] Field Output Polarity (DVI and Analog) This bit sets the polarity of the field output signal on Pin 21. 0 = active low = even field; active high = odd field. 1 = active low = odd field; active high = even field. The power-up default setting is 1. 0x24--Bit[3] SOG Output Polarity This bit sets the polarity of the SOGOUT signal (analog only). 0 = active low. 1 = active high. The power-up default setting is 1. 0x21--Bit[3] Auto-Offset Clamp Mode 0x24--Bits[2:1] SOG Output Select This bit specifies if the auto-offset measurement takes place during clamp or either 10 or 16 clocks afterward. The measurement takes 6 clock cycles. 0 = auto offset measurement takes place during clamp period. 1 = auto offset measurement is set by 0x21, Bit 2. Default = 1. These register bits control the output on the SOGOUT pin. Options are the raw SOG from the slicer (this is the unprocessed SOG signal produced from the sync slicer), the raw HSYNC, the regenerated sync from the sync filter, which can generate missing syncs because of coasting or dropout, or the filtered sync that excludes extraneous syncs not occurring within the sync filter window. The power-up default setting is 11. 0x21--Bit[2] Auto-Offset Clamp Length This bit sets the delay following the end of the clamp period for AO measurement. This bit is valid only if Register 0x21, Bit 3 = 1. 0 = delay is 10 clock cycles. 1 = delay is 16 clock cycles. Default = 1. Table 16. SOGOUT Polarity Settings 0x22--Bits[7:0] VSYNC Duration This is used to set the output duration of the VSYNC, and is designed to be used with the VSYNC filter. This is valid only if Register 0x21, Bit 4 is set to 1. Power-up default is 4. 0x23--Bits[7:0] HSYNC Duration An 8-bit register that sets the duration of the HSYNC output pulse. The leading edge of the HSYNC output is triggered by the internally generated, phase-adjusted PLL feedback clock. The AD9380 then counts a number of pixel clocks equal to the value in this register. This triggers the trailing edge of the HSYNC output, which is also phase-adjusted. The power-up default is 32. 0x24--Bit[7] HSYNC Output Polarity This bit sets the polarity of the HSYNC output. Setting this bit to 0 sets the HSYNC output to active low. Setting this bit to 1 sets the HSYNC output to active high. Power-up default setting is 1. SOGOUT Select 00 01 10 11 Function Raw SOG from sync slicer (SOG0 or SOG1) Raw HSYNC (HSYNC0 or HSYNC1) Regenerated sync from sync filter HSYNC to PLL 0x24--Bit[0] Output Clock Invert This bit allows inversion of the output clock as specified by Register 0x25, Bit 7 to Bit 6. 0 = noninverted clock. 1 = inverted clock. The power-up default setting is 0. 0x25--Bits[7:6] Output Clock Select These bits select the clock output on the DATACK pin. They include a 1/2x clock, a 2x clock, a 90 phase shifted clock, or the normal pixel clock. The power-up default setting is 01. Table 17. Output Clock Select Select 00 01 10 11 Rev. 0 | Page 42 of 60 Result 1/2x pixel clock 1x pixel clock 2x pixel clock 90 phase 1x pixel clock AD9380 0x25--Bits[5:4] Output Drive Strength 0x26--Bit[7] Output Three-State These two bits select the drive strength for all the high speed digital outputs (except VSOUT, A0, and O/E field). Higher drive strength results in faster rise/fall times and in general makes it easier to capture data. Lower drive strength results in slower rise times/fall times and helps to reduce EMI and digitally generated power supply noise. The power-up default setting is 11. When enabled, this bit puts all outputs (except SOGOUT) in a high impedance state. 0 = normal outputs. 1 = all outputs (except SOGOUT) in high impedance mode. The power-up default setting is 0. Table 18. Output Drive Strength Output Drive 00 01 10 11 Result Low output drive strength Medium low output drive strength Medium high output drive strength High output drive strength When enabled, this bit places the S/PDIF audio output pins in a high impedance state. 0 = normal S/PDIF output. 1 = S/PDIF pins in high impedance mode. The power-up default setting is 0. These bits choose between four options for the output mode, one of which is exclusive to an HDMI input. 4:4:4 mode is standard RGB; 4:2:2 mode is YCrCb, which reduces the number of active output pins from 24 to 16; 4:4:4 is double data rate (DDR) output mode; and the data is RGB mode, but changes on every clock edge. The power-up default setting is 00. Table 19. Output Mode 10 11 When enabled, this bit allows the SOGOUT pin to be placed in a high impedance state. 0 = normal SOG output. 1 = SOGOUT pin is in high impedance mode. The power-up default setting is 0. 0x26--Bits[5] S/PDIF Three-State 0x25--Bits[3:2] Output Mode Output Mode 00 01 0x26--Bits[6] SOG Three-State 0x26--Bits[4] I2S Three-State When enabled, this bit places the I2S output pins in a high impedance state. 0 = normal I2S output. 1 = I2S pins in high impedance mode. The power-up default setting is 0. 0x26--Bits[3] Power-Down Polarity This bit defines the polarity of the input power-down pin. 0 = power-down pin is active low. 1 = power-down pin is active high. The power-up default setting is 1. Result 4:4:4 RGB mode 4:2:2 YCrCb mode + DDR 4:2:2 on blue (secondary) DDR 4:4:4: DDR mode + DDR 4:2:2 on blue (secondary) 12-bit 4:2:2 (HDMI option only) 0x26--Bits[2:1] Power-Down Pin Function 0x25--Bit[1] Primary Output Enable This bit places the primary output in active or high impedance mode. The primary output is designated when using either 4:2:2 or DDR 4:4:4. In these modes, the data on the red and green output channels is the primary output, while the output data on the blue channel (DDR YCrCb) is the secondary output. 0 = primary output is in high impedance mode. 1 = primary output is enabled. The power-up default setting is 1. These bits define the different operational modes of the powerdown pin. These bits are functional only when the power-down pin is active; when it is not active, the part is powered up and functioning. The power-up default setting is 00. Table 20. Power-Down Pin Function Function 00 01 10 11 Result The chip is powered down and all outputs except SOGOUT are in high impedance mode. The chip is powered down and all outputs are in high impedance mode. The chip remains powered up, but all outputs except SOGOUT are in high impedance mode. The chip remains powered up, but all outputs are in high impedance mode. 0x25--Bit[0] Secondary Output Enable 0x26--Bit[0] Power-Down This bit places the secondary output in active or high impedance mode. This bit is used to put the chip in power-down mode. In this mode, the chip's power dissipation is reduced to a fraction of the typical power (see Table 1 for exact power dissipation). When in power-down, the HSOUT, VSOUT, DATACK, and all 30 of the data outputs are put into a high impedance state. Note that the SOGOUT output is not put into high impedance. Circuit blocks that continue to be active during power-down include the voltage references, sync processing, sync detection, and the serial register. These blocks facilitate a fast start-up from power-down. 0 = normal operation. 1 = power-down mode. The power-up default setting is 0. The secondary output is designated when using either 4:2:2 or DDR 4:4:4. In these modes, the data on the blue output channel is the secondary output, while the output data on the red and green channels is the primary output. Secondary output is always a DDR YCrCb data mode. 0 = secondary output is in high impedance mode. 1 = secondary output is enabled. The power-up default setting is 0. Rev. 0 | Page 43 of 60 AD9380 0x27--Bit[7] Auto Power-Down Enable 0x2B--Bits[7:0] Line Width LSBs This bit enables the chip to go into low power mode, or seek mode if no sync inputs are detected. 0 = auto power-down disabled. 1 = chip powers down if no sync inputs present. The power-up default setting is 1. See the line width MSBs section. 0x27--Bit[6] HDCP A0 Address This bit sets the LSB of the address of the HDCP I2C. This should be set to 1 only for a second receiver in a dual-link configuration. The power-up default is 0. 0x2C--Bits[3:0] Screen Height MSBs Along with the 8 bits following these 12 bits, set the height of the active screen (in lines). The power-up default setting is 0x2D0. 0x2D--Bits[7:0] Screen Height LSBs See the Screen Height MSBs section. 0x27--Bits[5] MCLK External Enable 0x2E--Bit[7] Ctrl Enable This bit enables the MCLK to be supplied externally. If an external MCLK is used, then it must be locked to the video clock according to the CTS and N available in the I2C. Any mismatch between the internal MCLK and the input MCLK results in dropped or repeated audio samples. 0 = use internally generated MCLK. 1 = use external MCLK input. The power-up default setting is 0. When set, this bit allows Ctrl [3:0] signals decoded from the DVI to be output on the I2S data pins. 0 = I2S signals on I2S lines. 1 = Ctrl [3:0] output on I2S lines. The power-up default setting is 0. 0x2E--Bits[6:5] I2S Output Mode BT656 GENERATION These bits select between four options for the I2S output: I2S, right-justified, left-justified, or raw IEC60958 mode. The power-up default setting is 00. 0x27--Bit[4] BT656 Enable Table 21. I2S Output Select This bit enables the output to be BT656 compatible with the defined start of active video (SAV) and the end of active video (EAV) controls to be inserted. These require specification of the number of active lines, active pixels per line, and delays to place these markers. 0 = disable BT656 video mode. 1 = enable BT656 video mode. The power-up default setting is 0. I2S Output Mode 00 01 10 11 0x27--Bit[3] Force DE Generation These bits set the I2S bit width for right-justified mode. The power-up default setting is 24 bits. This bit allows the use of the internal DE generator in DVI mode. 0 = internal DE generation disabled. 1 = force DE generation via programmed registers. The power-up default setting is 0. Result I2S mode Right-justified Left-justified Raw IEC60958 mode 0x2E--Bits[4:0] I2S Bit Width 0x2F--Bit[6] TMDS Sync Detect This read-only bit indicates the presence of a TMDS DE. 0 = no TMDS DE present. 1 = TMDS DE detected. 0x27--Bits[2:0] Interlace Offset These bits define the offset in HSYNCs from Field 0 to Field 1. The power-up default setting is 000. 0x28--Bits[7:2] VSYNC Delay 0x2F--Bit[5] TMDS Active This read-only bit indicates the presence of a TMDS clock. 0 = no TMDS clock present. 1 = TMDS clock detected. 0x2F--Bit[4] AV Mute These bits set the delay (in lines) from the leading edge of VSYNC to active video. The power-up default setting is 24. This read-only bit indicates the presence of AV mute based on general control packets. 0 = AV not muted. 1 = AV muted. 0x28--Bits[1:0] HSYNC Delay MSBs These 8 bits and the following 10 bits set the delay (in pixels) from the HSYNC leading edge to the start of active video. The power-up default setting is 0x104. 0x29--Bits[7:0] HSYNC Delay LSBs 0x2F--Bit[3] HDCP Keys Read This read-only bit reports if the HDCP keys were read successfully. 0 = failure to read HDCP keys. 1 = HDCP keys read. 0x2F--Bit[2:0] HDMI Quality See the HSYNC Delay MSBs section. 0x2A--Bits[3:0] Line Width MSBs These 8 bits and the following 12 bits set the width of the active video line (in pixels). The power-up default setting is 0x500. These read-only bits indicate a level of HDMI quality based on the display enable (DE) edges. The 3 bits correspond to the R, G, and B channels of the TMDS signals. If an extraneous signal is present on any channel, that bit is set. A value of 000 represents the highest quality. Rev. 0 | Page 44 of 60 AD9380 0x30--Bits[6] HDMI Content Encrypted 0x32--Bits[6] Macrovision PAL Enable This read-only bit is high when HDCP decryption is in use (content is protected). The signal goes low when HDCP is not being used. Customers can use this bit to determine whether to allow copying of the content. The bit should be sampled at regular intervals because it can change on a frame by frame basis. 0 = HDCP not in use. 1 = HDCP decryption in use. Tells the Macrovision detection engine to enter PAL mode when set to 1. Default is 0 for NTSC mode. 0x30--Bit[5] DVI HSYNC Polarity 0x32--Bits[5:0] Macrovision Line Count Start Set the start line for Macrovision detection. Along with Register 0x33, Bits [5:0] they define the region where MV pulses are expected to occur. The power-up default is Line 13. 0x33--Bit[7] Macrovision Detect Mode This read-only bit indicates the polarity of the DVI HSYNC. 0 = DVI HSYNC polarity is low active. 1 = DVI HSYNC polarity is high active. 0 = standard definition. 1 = progressive scan mode. 0x30--Bit[4] DVI VSYNC Polarity 0x33--Bit[6] Macrovision Settings Override This read-only bit indicates the polarity of the DVI VSYNC. 0 = DVI VSYNC polarity is low active. 1 = DVI VSYNC polarity is high active. This defines whether preset values are used for the MV line counts and pulse widths or the values stored in I2C registers are used. 0 = use hard coded settings for line counts and pulse widths. 1 = use I2C values for these settings. Default = 0. 0x30--Bits[3:0] HDMI Pixel Repetition These read-only bits indicate the pixel repetition on DVI. 0 = 1x, 1 = 2x, 2 = 3x, up to a maximum repetition of 10x (0x9). Table 22. Select 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 Repetition Multiplier 1x 2x 3x 4x 5x 6x 7x 8x 9x 10x 0x33--Bits[5:0] Macrovision Line Count End Set the end line for Macrovision detection. Along with Register 0x32, Bits [5:0] they define the region where MV pulses are expected to occur. The power-up default is Line 21. 0x34--Bits[7:6] Macrovision Pulse Limit Select Set the number of pulses required in the last three lines (SD mode only). If there is not at least this number of MV pulses, the engine stops. These two bits define the following pulse counts: 00 = 6 01 = 4 10 = 5 (default) 11 = 7 0x34--Bit[5] Low Frequency Mode MACROVISION Sets whether the audio PLL is in low frequency mode. Low frequency mode should only be set for pixel clocks < 80 MHz. 0x31--Bits[7:4] Macrovision Pulse Max These bits set the pseudo sync pulse width maximum for Macrovision detection in pixel clocks. This is functional for 13.5 MHz SDTV or 27 MHz progressive scan. Power-up default is 9. 0x34--Bit[4] Low Frequency Override Allows the previous bit to be used to set low frequency mode rather than the internal autodetect. 0x34--Bit[3] Up Conversion Mode 0x31--Bits[3:0] Macrovision Pulse Min 0 = repeat Cb/Cr values. 1 = interpolate Cb/Cr values. These bits set the pseudo sync pulse width maximum for Macrovision detection in pixel clocks. This is functional for 13.5 MHz SDTV or 27 MHz progressive scan. Power-up default is 6. 0x34--Bit[2] CbCr Filter Enable Enables the FIR filter for 4:2:2 CbCr output. 0x32--Bit[7] Macrovision Oversample Enable Tells the Macrovision detection engine whether oversampling is being used. This accommodates 27 MHz sampling for SDTV and 54 MHz sampling for progressive scan and is used as a correction factor for clock counts. Power-up default is 0. Rev. 0 | Page 45 of 60 AD9380 COLOR SPACE CONVERSION 0x39--Bits[4:0] CSC A3 MSBs The default power up values for the color space converter coefficients (R0x35 through R0x4C) are set for ATSC RGB to YCbCr conversion. They are completely programmable for other conversions. The default value for the 13-bit A3 is 0x0000. 0x3A--Bits[7:0] CSC A3 LSBs 0x3B--Bits[4:0] CSC A4 MSBs The default value for the 13-bit A4 is 0x19D7. 0x34--Bit[1] Color Space Converter Enable This bit enables the color space converter. 0 = disable color space converter. 1 = enable color space converter. The power-up default setting is 0. 0x3C--Bits[7:0] CSC A4 LSBs 0x3D--Bits[4:0] CSC B1 MSBs 0x35--Bits[6:5] Color Space Converter Mode 0x3E--Bits[7:0] CSC B1 LSBs 0x3F--Bits[4:0] CSC B2 MSB These two bits set the fixed-point position of the CSC coefficients, including the A4, B4, and C4 offsets. The default value for the 13-bit B2 is 0x0800. Table 23. CSC Fixed Point Converter Mode Select 00 01 1x 0x40--Bits[7:0] CSC B2 LSBs 0x41--Bits[4:0] CSC B3 MSBs Result 1.0, -4096 to +4095 2.0, -8192 to +8190 4.0, -16384 to +16380 The default value for the 13-bit B3 is 0x1E89. 0x35--Bits[4:0] Color Space Conversion Coefficient A1 MSBs These 5 bits form the 5 MSBs of the Color Space Conversion Coefficient A1. This combined with the 8 LSBs of the following register form a 13-bit, twos complement coefficient which is user programmable. The equation takes the form of: The default value for the 13-bit B4 is 0x0291. 0x44--Bits[7:0] CSC B4 LSBs 0x45--Bits[4:0] CSC C1 MSBs The default value for the 13-bit C1 is 0x0000. The default value for the 13 bit C2 is 0x0800. The default value for the 13-bit A1 coefficient is 0x0C52. 0x36--Bits[7:0] Color Space Conversion Coefficient A1 LSBs See the Register 0x35 section. 0x48--Bits[7:0] CSC C2 LSBs 0x49--Bits[4:0] CSC C3 MSBs The default value for the 13-bit C3 is 0x0E87. 0x4A--Bits[7:0] CSC C3 LSBs 0x4B--Bits[4-0] CSC C4 MSBs 0x37--Bits[4:0] CSC A2 MSBs These five bits form the 5 MSBs of the Color Space Conversion Coefficient A2. Combined with the 8 LSBs of the following register, they form a 13-bit, twos complement coefficient that is user programmable. The equation takes the form of: The default value for the 13-bit A2 coefficient is 0x0800. 0x42--Bits[7:0] CSC B3 LSBs 0x43--Bits[4:0] CSC B4 MSBs 0x46--Bits[7:0] CSC C1 LSBs 0x47--Bits[4:0] CSC C2 MSBs ROUT = (A1 x RIN) + (A2 x GIN) + (A3 x BIN) + A4 GOUT = (B1 x RIN) + (B2 x GIN) + (B3 x BIN) + B4 BOUT = (C1 x RIN) + (C2 x GIN) + (C3 x BIN) + C4 ROUT = (A1 x RIN) + (A2 x GIN) + (A3 x BIN) + A4 GOUT = (B1 x RIN) + (B2 x GIN) + (B3 x BIN) + B4 BOUT = (C1 x RIN) + (C2 x GIN) + (C3 x BIN) + C4 The default value for the 13-bit B1 is 0x1C54. The default value for the 13-bit C4 is 0x18BD. 0x4C--Bits[7:0] CSC C4 LSBs 0x57--Bit[7] A/V Mute Override 0x57--Bit[6] A/V Mute Value 0x57--Bit[3] Disable AV Mute 0x57--Bit[2] Disable Audio Mute 0x58--Bit[7] MCLK PLL Enable This bit enables the use of the analog PLL. 0x38--Bits[7:0] CSC A2 LSBs See the Register 0x37 section. Rev. 0 | Page 46 of 60 AD9380 0x58--Bits[6:4] MCLK PLL_N 0x5A--Bit[6:0] Packet Detect These bits control the division of the MCLK out of the PLL. This register indicates if a data packet in specific sections has been detected. These seven bits are updated if any specific packet has been received since last reset or loss of clock detect. Normal is 0x00. Table 24. PLL_N [2:0] 0 1 2 3 4 5 6 7 MCLK Divide Value /1 /2 /3 /4 /5 /6 /7 /8 Table 26. 0x58--Bit[3] N_CTS_Disable This bit makes it possible to prevent the N/CTS packet on the link from writing to the N and CTS registers. Packet Detected AVI infoframe Audio infoframe SPD infoframe MPEG source infoframe ACP packets ISRC1 packets ISRC2 packets 0x5B--Bit[3] HDMI Mode 0 = DVI, 1 = HDMI. 0x58--Bit[2:0] MCLK fs_N These bits control the multiple of 128 fS used for MCLK out. Table 25. MCLK fs_N [2:0] 0 1 2 3 4 5 6 7 Packet Detect Bit 0 1 2 3 4 5 6 fS Multiple 128 256 384 512 640 768 896 1024 0x59--Bit[6] MDA/MCL PU Disable This bit disables the inter MDA/MCL pull-ups. 0x59--Bit[5] CLK Term O/R This bit allows for overriding during power down. 0 = auto, 1 = manual. 0x59--Bit[4] Manual CLK Term This bit allows normal clock termination or disconnects it. 0 = normal, 1 = disconnected. 0x59--Bit[2] FIFO Reset UF This bit resets the audio FIFO if underflow is detected. 0x59--Bit[1] FIFO Reset OF This bit resets the audio FIFO if overflow is detected. 0x59--Bit[0] MDA/MCL Three-State This bit three-states the MDA/MCL lines to allow in-circuit programming of the EEPROM. 0x5E--Bits[7:6] Channel Status Mode 0x5E--Bits[5:3] PCM Audio Data 0x5E--Bit[2] Copyright Information 0x5E--Bit[1] Linear PCM Identification 0x5E--Bit[0] Use of Channel Status Block 0x5F--Bits[7:0] Channel Status Category Code 0x60--Bits[7:4] Channel Number 0x60--Bits[3:0] Source Number 0x61--Bits[5:4] Clock Accuracy 0x61--Bits[3:0] Sampling Frequency Table 27. Code 0x0 0x2 0x3 0x8 0xA 0xC 0xE Frequency (kHz) 44.1 48 32 88.2 96 176.4 192 0x62--Bits[3:0] Word Length 0x7B--Bits[7:0] CTS (Cycle Time Stamp) (19:12) These are the most significant 8 bits of a 20-bit word used in the 20-bit N term in the regeneration of the audio clock. 0x7C--Bits[7:0] CTS (11:4) 0x7D--Bits[7:4] CTS (3:0) 0x7D--Bits[3:0] N (19:16) These are the most significant 4 bits of a 20-bit word used along with the 20-bit CTS term to regenerate the audio clock. 0x80--Bits[AVI] Infoframe Version Rev. 0 | Page 47 of 60 AD9380 0x81--Bits[6:5] Y [1:0] 0x85--Bits[3:0] Pixel Repeat This register indicates whether data is RGB, 4:4:4, or 4:2:2. This value indicates how many times the pixel was repeated. 0x0 = no repeats, sent once, 0x8 = 8 repeats, sent 9 times, and so on. Table 28. Y 00 01 10 Video Data RGB YCbCr 4:2:2 YCbCr 4:4:4 0x81--Bits[4] Active Format Information Present 0 = no data. 1 = active format information valid. 0x81--Bits[3:2] Bar Information Table 29. B 00 01 10 11 Bar Type No bar information Horizontal bar information valid Vertical bar information valid Horizontal and vertical bar information valid 0x81--Bits[1:0] Scan Information Table 30. S [1:0] 00 01 10 Scan Type No information Overscanned (television) Underscanned (computer) 0x82--Bits[7:6] Colorimetry Table 31. C [1:0] 00 01 10 Colorimetry No data SMPTE 170M, ITU601 ITU 709 0x82--Bits[5:4] Picture Aspect Ratio Table 32. M[1:0] 00 01 10 Aspect Ratio No data 4:3 16:9 0x82--Bits[3:0] Active Format Aspect Ratio Table 33. R [3:0] 0x8 0x9 0xA 0xB Active Format A/R Same as picture aspect ratio (M [1:0]) 4:3 (center) 16:9 (center) 14:9 (center) 0x83--Bits[1:0] Nonuniform Picture Scaling Table 34. SC [1:0] 00 01 10 11 Picture Scaling No known nonuniform scaling Has been scaled horizontally Has been scaled vertically Has been scaled both horizontally and vertically 0x84--Bits[6:0] Video ID Code 0x86--Bits[7:0] Active Line Start LSB Combined with the MSB in Register 0x88, these bits indicate the beginning line of active video. All lines before this comprise a top horizontal bar. This is used in letter box modes. If the 2byte value is 0x00, there is no horizontal bar. 0x87--Bits[6:0] New Data Flags (NDF) This register indicates whether data in specific sections has changed. In the address space from 0x80 to 0xFF, each register address ending in 0b111 (for example, 0x87, 0x8F, 0x97, 0xAF) is an NDF register. They all have the same data and all are reset upon reading any one of them. Table 35. NDF Bit Number 0 1 2 3 4 5 6 Changes Occurred AVI infoframe Audio infoframe SPD infoframe MPEG source infoframe ACP packets ISRC1 packets ISRC2 packets 0x88--Bits[7:0] Active Line Start MSB See Register 0x86. 0x89--Bits[7:0] Active Line End LSB Combined with the MSB in Register 0x8A, these bits indicate the last line of active video. All lines past this comprise a lower horizontal bar. This is used in letter-box modes. If the 2-byte value is greater than the number of lines in the display, there is no lower horizontal bar. 0x8A--Bits[7:0] Active Line End MSB See Register 0x89. 0x8B--Bits[7:0] Active Pixel Start LSB Combined with the MSB in Register 0x8C, these bits indicate the first pixel in the display which is active video. All pixels before this comprise a left vertical bar. If the 2-byte value is 0x00, there is no left bar. 0x8C--Bits[7:0] Active Pixel Start MSB See Register 0x8B. 0x8D--Bits[7:0] Active Pixel End LSB Combined with the MSB in Register 0x8E, these bits indicate the last active video pixel in the display. All pixels past this comprise a right vertical bar. If the 2-byte value is greater than the number of pixels in the display, there is no vertical bar. See CEA EDID short video descriptors. Rev. 0 | Page 48 of 60 AD9380 0x8E--Bits[7:0] Active Pixel End MSB See Register 0x8D. 0x8F--Bits[6:0] NDF See Register 0x87. 0x90--Bits[7:0] Audio Infoframe Version 0x91--Bits[7:4] Audio Coding Type These bits identify the audio coding so that the receiver may process audio properly. Table 36. CT [3:0] 0x0 0x1 0x2 0x3 0x4 0x5 0x6 0x7 0x8 Audio Coding Refer to stream header IEC60958 PCM AC-3 MPEG1 (Layer 1 and Layer 2) MP3 (MPEG1 Layer 3) MPEG2 (multichannel) AAC DTS ATRAC 0x91--Bits[2:0] Audio Channel Count 0x92--Bits[4:2] Sampling Frequency 0x92--Bits[1:0] Ample Size 0x93--Bits[7:0] Max Bit Rate For compressed audio only, when this value is multiplied by 8 kHz represents the maximum bit rate. A value of 0x08 in this field yields a maximum bit rate of (8 kHz x 8 kHz = 64 kHz). 0x94--Bits[7:0] Speaker Mapping These bits define the mapping (suggested placement) of speakers. Table 38. Abbreviation FL FC FR FCL FCR RL RC RR RCL RCR LFE These bits specify how many audio channels are being sent: 2 channels to 8 channels. Table 37. CC [2:0] 000 001 010 011 100 101 110 111 Channel Count Refer to stream header 2 3 4 5 6 7 8 Rev. 0 | Page 49 of 60 Speaker Placement Front left Front center Front right Front center left Front center right Rear left Rear center Rear right Rear center left Rear center right Low frequency effect AD9380 Table 39. CA Bit 4 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Bit 3 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 Bit 2 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 Bit 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 Bit 0 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 Channel Number Bit 8 Bit 7 - - - - - RRC RRC RRC RRC FRC FRC FRC FRC FRC FRC FRC FRC FRC FRC FRC FRC - RC RC RC RC RLC RLC RLC RLC FLC FLC FLC FLC FLC FLC FLC FLC FLC FLC FLC FLC 0x95--Bit[7] Down-Mix Inhibit 0x95--Bits[6:3] Level Shift Values These bits define the amount of attenuation. The value directly corresponds to the amount of attenuation: for example, 0000 = 0 dB, 0001 = 1 dB to 1111 = 15 dB attenuation. 0x96--Bits[7:0] Reserved 0x97--Bits[6:0] New Data Flags Bit 6 Bit 5 RR RR RR RR RR RR RR RR RR RR RR RR - - - - - - - - RR RR RR RR RC RC RC RC RL RL RL RL RL RL RL RL RL RL RL RL - - - - RC RC RC RC RL RL RL RL Bit 4 - - FC FC - - FC FC - - FC FC - - FC FC - - FC FC - v FC FC - - FC FC - - FC FC Bit 3 - LFE - LFE - LFE - LFE - LFE - LFE - LFE - LFE - LFE - LFE v LFE - LFE - LFE - LFE v LFE - LFE Bit 2 FR FR FR FR FR FR FR FR FR FR FR FR FR FR FR FR FR FR FR FR FR FR FR FR FR FR FR FR FR FR FR FR Bit 1 FL FL FL FL FL FL FL FL FL FL FL FL FL FL FL FL FL FL FL FL FL FL FL FL FL FL FL FL FL FL FL FL 0x9A--Bits[7:0] VN2 0x9B--Bits[7:0] VN3 0x9C--Bits[7:0] VN4 0x9D--Bits[7:0] VN5 0x9E--Bits[7:0] VN6 0x9F--Bits[6:0] New Data Flags See Register 0x87 for a description. See Register 0x87 for a description. 0xA0--Bits[7:0] VN7 0xA1--Bits[7:0 VN8 0xA2--Bits[7:0] Product Description Character 1 (PD1) 0x98--Bits[7:0] Source Product Description (SPD) Infoframe Version 0x99--Bits[7:0] Vender Name Character 1 (VN1) This is the first character in eight character name of the company that appears on the product. The data characters are 7-bit ASCII code. This is the first character of 16 that contains the model number and a short description of the product. The data characters are 7-bit ASCII code. Rev. 0 | Page 50 of 60 AD9380 0xA3--Bits[7:0] PD2 0xA4--Bits[7:0] PD3 0xA5--Bits[7:0] PD4 0xA6--Bits[7:0] PD5 0xA7--Bits[6:0] New Data Flags 0xBD--Bit[4] Field Repeat This bit defines whether the field is new or repeated. 0 = new field or picture. 1 = repeated field. 0xBD--Bits[1:0] MPEG Frame These bits identify the frame as I, B, or P. See Register 0x87 for a description. Table 41. 0xA8--Bits[7:0] PD6 0xA9--Bits[7:0] PD7 0xAA--Bits[7:0] PD8 0xAB--Bits[7:0] PD9 0xAC--Bits[7:0] PD10 0xAD--Bits[7:0] PD11 0xAE--Bits[7:0] PD12 0xAF--Bits[6:0] New Data Flags MF [1:0] 00 01 10 11 0xBE--Bits[7:0] Reserved 0xBF--Bits[6:0] New Data Flags See Register 0x87 for a description. See Register 0x87 for a description. 0xC0--Bits[7:0] Audio Content Protection Packet (ACP Type) 0xB0--Bits[7:0] PD13 0xB1--Bits[7:0] PD14 0xB2--Bits[7:0 PD15 0xB3--Bits[7:0] PD16 0xB4--Bits[7:0] Source Device Information Code These bits define which audio content protection is used. Table 42. Code 0x00 0x01 0x02 0x03 0x04--0xFF These bytes classify the source device. Table 40. SDI Code 0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08 0x09 Source Unknown Digital STB DVD D-VHS HDD video DVC DSC Video CD Game PC general ACP Type Generic audio IEC 60958-identified audio DVD-audio Reserved for super audio CD (SACD) Reserved 0xC1--ACP Packet Byte 0 (ACP_PB0) 0xC2--Bits[7:0] ACP_PB1 0xC3--Bits[7:0] ACP_PB2 0xC4--Bits[7:0] ACP_PB3 0xC5--Bits[7:0] ACP_PB4 0xC7--Bits[6:0] New Data Flags See Register 0x87 for a description. 0xC8--Bit[7] International Standard Recording Code (ISRC1) Continued 0xB7--Bits[6:0] New Data Flags See Register 0x87 for a description. This bit indicates that a continuation of the 16 ISRC1 packet bytes (an ISRC2 packet) is being transmitted. 0xB8--Bits[7:0] MPEG Source Infoframe Version 0xB9--Bits[7:0] MPEG Bit Rate Byte 0 (MB0) 0xC8--Bit[6] ISRC1 Valid This is the lower 8 bits of 32 bits that specify the MPEG bit rate in Hz. 0xBA--Bits[7:0] MB1 0xBB--Bits[7:0] MB2 0xBC--Bits[7:0] MB3--Upper Byte Frame Type Unknown I--picture B--picture P--picture This bit indicates whether ISRC1 packet bytes are valid. 0 = ISRC1 status bits and PBs not valid. 1 = ISRC1 status bits and PBs valid. 0xC8--Bits[2:0] ISRC Status These bits define where the samples are in the ISRC track. At least two transmissions of 001 occur at the beginning of the track, while in the middle of the track, continuous transmission of 010 occurs. This is followed by at least two transmissions of 100 near the end of the track. Rev. 0 | Page 51 of 60 AD9380 0xC9--Bits[7:0] ISRC1 Packet Byte 0 (ISRC1_PB0) 0xCA--Bits[7:0] ISRC1_PB1 0xCB--Bits[7:0] ISRC1_PB2 0xCC--Bits[7:0] ISRC1_PB3 0xCD--Bits[7:0] ISRC1_PB4 0xCE--Bits[7:0] ISRC1_PB5 0xCF--Bits[6:0] New Data Flags See Register 0x87 for a description. 0xD0--Bits[7:0] ISRC1_PB6 0xD1--Bits[7:0] ISRC1_PB7 0xD2--Bits[7:0] ISRC1_PB8 0xD3--Bits[7:0] ISRC1_PB9 0xD4--Bits[7:0] ISRC1_PB10 0xD5--Bits[7:0] ISRC1_PB11 0xD6--Bits[7:0] ISRC1_PB12 0xD7--Bits[6:0] New Data Flags See Register 0x87 for a description. 0xD8--Bits[7:0] ISRC1_PB13 0xD9--Bits[7:0] ISRC1_PB14 0xDA--Bits[7:0] ISRC1_PB15 0xDB--Bits[7:0] SRC1_PB16 0xDC--Bits[7:0] ISRC2 Packet Byte 0 (ISRC2_PB0) 0xDD--Bits[7-0] ISRC2_PB1 0xDE--Bits[7-0] ISRC2_PB2 0xDF--Bits[6-0] New Data Flags See Register 0x87 for a description. 0xE0--Bits[7:0] ISRC2_PB3 0xE1--Bits[7:0] ISRC2_PB4 0xE2--Bits[7:0] ISRC2_PB5 0xE3--Bits[7:0] ISRC2_PB6 0xE4--Bits[7:0] ISRC2_PB7 0xE5--Bits[7:0] ISRC2_PB8 0xE6--Bits[7:0] ISRC2_PB9 0xE7--Bits[6:0] New Data Flags See Register 0x87 for a description. 0xE8--Bits[7:0] ISRC2_PB10 0xE9--Bits[7:0] ISRC2_PB11 0xEA--Bits[7:0] ISRC2_PB12 0xEB--Bits[7:0] ISRC2_PB13 0xEC--Bits[7:0] ISRC2_PB14 0xED--Bits[7:0] ISRC2_PB15 0xEE--Bits[7:0] ISRC2_PB16 This byte is transmitted only when the ISRC continue bit (Register 0xC8 Bit 7) is set to 1. Rev. 0 | Page 52 of 60 AD9380 2-WIRE SERIAL CONTROL PORT A 2-wire serial interface control interface is provided in the AD9380. Up to two AD9380 devices can be connected to the 2-wire serial interface, with a unique address for each device. DATA TRANSFER VIA SERIAL INTERFACE The 2-wire serial interface comprises a clock (SCL) and a bidirectional data (SDA) pin. The analog flat panel interface acts as a slave for receiving and transmitting data over the serial interface. When the serial interface is not active, the logic levels on SCL and SDA are pulled high by external pull-up resistors. If the AD9380 does not acknowledge the master device during a write sequence, the SDA remains high so the master can generate a stop signal. If the master device does not acknowledge the AD9380 during a read sequence, the AD9380 interprets this as the end of data. The SDA remains high, so the master can generate a stop signal. Data received or transmitted on the SDA line must be stable for the duration of the positive-going SCL pulse. Data on SDA must change only when SCL is low. If SDA changes state while SCL is high, the serial interface interprets that action as a start or stop sequence. There are six components to serial bus operation: * Start signal * Slave address byte * Base register address byte * Data byte to read or write * Stop signal * Acknowledge (ack) The first 8 bits of data transferred after a start signal comprise a 7-bit slave address (the first 7 bits) and a single R/W bit (the 8th bit). The R/W bit indicates the direction of data transfer, read from (1) or write to (0) the slave device. If the transmitted slave address matches the address of the device (set by the state of the SA0 input pin as shown in Table 43), the AD9380 acknowledges by bringing SDA low on the 9th SCL pulse. If the addresses do not match, the AD9380 does not acknowledge. Table 43. Serial Port Addresses Bit 6 A5 0 Bit 5 A4 0 To write data to specific control registers of the AD9380, the 8-bit address of the control register of interest must be written after the slave address has been established. This control register address is the base address for subsequent write operations. The base address auto-increments by 1 for each byte of data written after the data byte intended for the base address. If more bytes are transferred than there are available addresses, the address does not increment and remains at its maximum value. Any base address higher than the maximum value does not produce an acknowledge signal. Data are read from the control registers of the AD9380 in a similar manner. Reading requires two data transfer operations: When the serial interface is inactive (SCL and SDA are high) communications are initiated by sending a start signal. The start signal is a high-to-low transition on SDA while SCL is high. This signal alerts all slave devices that a data transfer sequence is coming. Bit 4 A3 1 Bit 3 A2 1 Bit 2 A1 0 Bit 1 A0 0 * The base address must be written with the R/W bit of the slave address byte low to set up a sequential read operation. * Reading (the R/W bit of the slave address byte high) begins at the previously established base address. The address of the read register auto-increments after each byte is transferred. To terminate a read/write sequence to the AD9380, a stop signal must be sent. A stop signal comprises a low-to-high transition of SDA while SCL is high. A repeated start signal occurs when the master device driving the serial interface generates a start signal without first generating a stop signal to terminate the current communication. This is used to change the mode of communication (read, write) between the slave and master without releasing the serial interface lines. SDA tBUFF tSTAH tDSU tDHO tSTASU tSTOSU tDAL SCL 05688-017 Bit 7 A6 (MSB) 1 For each byte of data read or written, the MSB is the first bit of the sequence. tDAH Figure 17. Serial Port Read/Write Timing Rev. 0 | Page 53 of 60 AD9380 SERIAL INTERFACE READ/WRITE EXAMPLES Read from one control register: Write to one control register: * Start signal * Start signal * Slave address byte (R/W\ bit = low) * Slave address byte (R/W bit = low) * Base address byte * Base address byte * Start signal * Data byte to base address * Slave address byte (R/W\ bit = high) * Stop signal * Data byte from base address Write to four consecutive control registers: * Stop signal * Start signal Read from four consecutive control registers: * Slave address byte (R/W bit = low) * Start signal * Base address byte * Slave address byte (R/W bit = low) * Data byte to base address * Base address byte * Data byte to (base address + 1) * Start signal * Data byte to (base address + 2) * Slave address byte (R/W bit = high) * Data byte to (base address + 3) * Data byte from base address * Stop signal * Data byte from (base address + 1) * Data byte from (base address + 2) * Data byte from (base address + 3) * Stop signal BIT 7 BIT 6 BIT 5 BIT 4 BIT 3 BIT 2 BIT 1 BIT 0 ACK 05688-018 SDA SCL Figure 18. Serial Interface--Typical Byte Transfer Rev. 0 | Page 54 of 60 AD9380 PCB LAYOUT RECOMMENDATIONS The AD9380 is a high precision, high speed analog device. To achieve the maximum performance from the part, it is important to have a well laid-out board. The following is a guide for designing a board using the AD9380. The bypass capacitors should be physically located between the power plane and the power pin. Current should flow from the power plane to the capacitor to the power pin. Do not make the power connection between the capacitor and the power pin. Placing a via underneath the capacitor pads down to the power plane is generally the best approach. ANALOG INTERFACE INPUTS Using the following layout techniques on the graphics inputs is extremely important: * Minimize the trace length running into the graphics inputs. To accomplished this, place the AD9380 as close as possible to the graphics VGA connector. Long input trace lengths are undesirable, because they pick up more noise from the board and other external sources. * Place the 75 termination resistors (see Figure 3) as close to the AD9380 chip as possible. Any additional trace length between the termination resistors and the input of the AD9380 increases the magnitude of reflections, which corrupts the graphics signal. * Use 75 matched impedance traces. Trace impedances other than 75 also increase the chance of reflections. The AD9380 has very high input bandwidth (300 MHz). While this is desirable for acquiring a high resolution PC graphics signal with fast edges, it means that it also captures any high frequency noise present. Therefore, it is important to reduce the amount of noise that gets coupled to the inputs. Avoid running any digital traces near the analog inputs. Due to the high bandwidth of the AD9380, sometimes low-pass filtering the analog inputs can help to reduce noise. For many applications, filtering is unnecessary. Experiments have shown that placing a series ferrite bead prior to the 75 termination resistor is helpful in filtering out excess noise. Specifically, the part used was the Fair-Rite 2508051217Z0, but each application may work best with a different bead value. Alternatively, placing a 100 to 120 resistor between the 75 termination resistor and the input coupling capacitor can also be beneficial. POWER SUPPLY BYPASSING It is recommended to bypass each power supply pin with a 0.1 F capacitor. The exception is in the case where two or more supply pins are adjacent to each other. For these groupings of powers/grounds, it is only necessary to have one bypass capacitor. The fundamental idea is to have a bypass capacitor within about 0.5 cm of each power pin. Also, avoid placing the capacitor on the opposite side of the PC board from the AD9380, because that interposes resistive vias in the path. It is particularly important to maintain low noise and good stability of PVDD (the clock generator supply). Abrupt changes in PVDD can result in similarly abrupt changes in sampling clock phase and frequency. This can be avoided by careful attention to regulation, filtering, and bypassing. It is highly desirable to provide separate regulated supplies for each of the analog circuitry groups (VD and PVDD). Some graphic controllers use substantially different levels of power when active (during active picture time) and when idle (during HSYNC and VSYNC periods). This can result in a measurable change in the voltage supplied to the analog supply regulator, which can in turn produce changes in the regulated analog supply voltage. This can be mitigated by regulating the analog supply, or at least PVDD, from a different, cleaner power source (for example, from a 12 V supply). It is recommended to use a single ground plane for the entire board. Experience has shown repeatedly that the noise performance is the same or better with a single ground plane. Using multiple ground planes can be detrimental because each separate ground plane is smaller and long ground loops can result. In some cases, using separate ground planes is unavoidable, so placing a single ground plane under the AD9380 is recommended. The location of the split should be at the receiver of the digital outputs. In this case, it is even more important to place components wisely because the current loops are much longer (current takes the path of least resistance). An example of a current loop is a power plane to AD9380 to digital output trace to digital data receiver to digital ground plane to analog ground plane. PLL Place the PLL loop filter components as close as possible to the FILT pin. Do not place any digital or other high frequency traces near these components. Use the values suggested in Figure 6 with 10% tolerances or less. Rev. 0 | Page 55 of 60 AD9380 OUTPUTS (BOTH DATA AND CLOCKS) DIGITAL INPUTS Try to minimize the trace length that the digital outputs have to drive. Longer traces have higher capacitance, which require more current that causes more internal digital noise. The digital inputs on the AD9380 were designed to work with 3.3 V signals, but are tolerant of 5.0 V signals. Therefore, no extra components need to be added if using 5.0 V logic. Shorter traces reduce the possibility of reflections. Any noise that enters the HSYNC input trace can add jitter to the system. Therefore, minimize the trace length and do not run any digital or other high frequency traces near it. Adding a series resistor of value 50 to 200 can suppress reflections, reduce EMI, and reduce the current spikes inside the AD9380. If series resistors are used, place them as close as possible to the AD9380 pins (although try not to add vias or extra length to the output trace to move the resistors closer). If possible, limit the capacitance that each of the digital outputs drives to less than 10 pF. This can be accomplished easily by keeping traces short and by connecting the outputs to only one device. Loading the outputs with excessive capacitance increases the current transients inside of the AD9380 and creates more digital noise on its power supplies. Rev. 0 | Page 56 of 60 AD9380 COLOR SPACE CONVERTER (CSC) COMMON SETTINGS Table 44. HDTV YCrCb (0 to 255) to RGB (0 to 255) (Default Setting for AD9380) Register Address Value Register Address Value Register Address Value 0x35 0x0C 0x3D 0x1C 0x45 0x00 Red/Cr Coeff 1 0x36 0x52 Green/Y Coeff 1 0x3E 0x54 Blue/Cb Coeff 1 0x46 0x00 0x37 0x08 0x3F 0x08 0x47 0x08 Red/Cr Coeff 2 0x38 0x00 Green/Y Coeff 2 0x40 0x00 Blue/Cb Coeff 2 0x48 0x00 0x39 0x00 0x41 0x3E 0x49 0x0E Red/Cr Coeff 3 0x3A 0x00 Green/Y Coeff 3 0x42 0x89 Blue/Cb Coeff 3 0x4A 0x87 0x3B 0x19 0x43 0x02 0x4B 0x18 Red/Cr Offset 0x3C 0xD7 Green/Y Offset 0x44 0x91 Blue/Cb Offset 0x4C 0xBD Table 45. HDTV YCrCb (16 to 235) to RGB (0 to 255) Register Address Value Register Address Value Register Address Value 0x35 0x47 0x3D 0x1D 0x45 0x00 Red/Cr Coeff 1 0x36 0x2C Green/Y Coeff 1 0x3E 0xDD Blue/Cb Coeff 1 0x46 0x00 0x37 0x04 0x3F 0x04 0x47 0x04 Red/Cr Coeff 2 0x38 0xA8 Green/Y Coeff 2 0x40 0xA8 Blue/Cb Coeff 2 0x48 0xA8 0x39 0x00 0x41 0x1F 0x49 0x08 Red/Cr Coeff 3 0x3A 0x00 Green/Y Coeff 3 0x42 0x26 Blue/Cb Coeff 3 0x4A 0x 75 0x3B 0x1C 0x43 0x01 0x4B 0x1B Red/Cr Offset 0x3C 0x1F Green/Y Offset 0x44 0x34 Blue/Cb Offset 0x4C 0x7B Table 46. SDTV YCrCb (0 to 255) to RGB (0 to 255) Register Address Value Register Address Value Register Address Value 0x35 0x2A 0x3D 0x1A 0x45 0x00 Red/Cr Coeff 1 0x36 0xF8 Green/Y Coeff 1 0x3E 0x6A Blue/Cb Coeff 1 0x46 0x00 0x37 0x08 0x3F 0x08 0x47 0x08 Red/Cr Coeff 2 0x38 0x00 Green/Y Coeff 2 0x40 0x00 Blue/Cb Coeff 2 0x48 0x00 0x39 0x00 0x41 0x1D 0x49 0x0D Red/Cr Coeff 3 0x3A 0x00 Green/Y Coeff 3 0x42 0x50 Blue/Cb Coeff 3 0x4A 0xDB 0x3B 0x1A 0x43 0x04 0x4B 0x19 Red/Cr Offset 0x3C 0x84 Green/Y Offset 0x44 0x23 Blue/Cb Offset 0x4C 0x12 Table 47. SDTV YCrCb (16 to 235) to RGB (0 to 255) Register Address Value Register Address Value Register Address Value 0x35 0x46 0x3D 0x1C 0x45 0x00 Red/Cr Coeff 1 0x36 0x63 Green/Y Coeff 1 0x3E 0xC0 Blue/Cb Coeff 1 0x46 0x00 0x37 0x04 0x3F 0x04 0x47 0x04 Red/Cr Coeff 2 0x38 0xA8 Green/Y Coeff 2 0x40 0xA8 Blue/Cb Coeff 2 0x48 0xA8 Rev. 0 | Page 57 of 60 0x39 0x00 0x41 0x1E 0x49 0x08 Red/Cr Coeff 3 0x3A 0x00 Green/Y Coeff 3 0x42 0x6F Blue/Cb Coeff 3 0x4A 0x11 0x3B 0x1C 0x43 0x02 0x4B 0x1B Red/Cr Offset 0x3C 0x84 Green/Y Offset 0x44 0x1E Blue/Cb Offset 0x4C 0xAD AD9380 Table 48. RGB (0 to 255) to HDTV YCrCb (0 to 255) Register Address Value Register Address Value Register Address Value 0x35 0x08 0x3D 0x03 0x45 0x1E Red/Cr Coeff 1 0x36 0x2D Green/Y Coeff 1 0x3E 0x68 Blue/Cb Coeff 1 0x46 0x21 0x37 0x18 0x3F 0x0B 0x47 0x19 Red/Cr Coeff 2 0x38 0x93 Green/Y Coeff 2 0x40 0x71 Blue/Cb Coeff 2 0x48 0xB2 0x39 0x1F 0x41 0x01 0x49 0x08 Red/Cr Coeff 0x3A 0x3F Green/Y Coeff 3 0x42 0x27 Blue/Cb Coeff 3 0x4A 0x2D 0x3B 0x08 0x43 0x00 0x4B 0x08 Red/Cr Offset 0x3C 0x00 Green/Y Offset 0x44 0x00 Blue/Cb Offset 0x4C 0x00 Table 49. RGB (0 to 255) to HDTV YCrCb (16 to 235) Register Address Value Register Address Value Register Address Value 0x35 0x07 0x3D 0x02 0x45 0x1E Red/Cr Coeff 1 0x36 0x06 Green/Y Coeff 1 0x3E 0xED Blue/Cb Coeff 1 0x46 0x64 0x37 0x19 0x3F 0x09 0x47 0x1A Red/Cr Coeff 2 0x38 0xA0 Green/Y Coeff 2 0x40 0xD3 Blue/Cb Coeff 2 0x48 0x96 0x39 0x1F 0x41 0x00 0x49 0x07 Red/Cr Coeff 3 0x3A 0x5B Green/Y Coeff 3 0x42 0xFD Blue/Cb Coeff 3 0x4A 0x06 0x3B 0x08 0x43 0x01 0x4B 0x08 Red/Cr Offset 0x3C 0x00 Green/Y Offset 0x44 0x00 Blue/Cb Offset 0x4C 0x00 Table 50. RGB (0 to 255) to SDTV YCrCb (0 to 255) Register Address Value Register Address Value Register Address Value 0x35 0x08 0x3D 0x04 0x45 0x1D Red/Cr Coeff 1 0x36 0x2D Green/Y Coeff 1 0x3E 0xC9 Blue/Cb Coeff 1 0x46 0x3F 0x37 0x19 0x3F 0x09 0x47 0x1A Red/Cr Coeff 2 0x38 0x27 Green/Y Coeff 2 0x40 0x64 Blue/Cb Coeff 2 0x48 0x93 0x39 0x1E 0x41 0x01 0x49 0x08 Red/Cr Coeff 3 0x3A 0xAC Green/Y Coeff 3 0x42 0xD3 Blue/Cb Coeff 3 0x4A 0x2D 0x3B 0x08 0x43 0x00 0x4B 0x08 Red/Cr Offset 0x3C 0x00 Green/Y Offset 0x44 0x00 Blue/Cb Offset 0x4C 0x00 Table 51. RGB (0 to 255) to SDTV YCrCb (16 to 235) Register Address Value Register Address Value Register Address Value 0x35 0x07 0x3D 0x04 0x45 0x1D Red/Cr Coeff 1 0x36 0x06 Green/Y Coeff 1 0x3E 0x1C Blue/Cb Coeff 1 0x46 0xA3 0x37 0x1A 0x3F 0x08 0x47 0x1B Red/Cr Coeff 2 0x38 0x1E Green/Y Coeff 2 0x40 0x11 Blue/Cb Coeff 2 0x48 0x57 Rev. 0 | Page 58 of 60 0x39 0x1E 0x41 0x01 0x49 0x07 Red/Cr Coeff 3 0x3A 0xDC Green/Y Coeff 3 0x42 0x91 Blue/Cb Coeff 3 0x4A 0x06 0x3B 0x08 0x43 0x01 0x4B 0x08 Red/Cr Offset 0x3C 0x00 Green/Y Offset 0x44 0x00 Blue/Cb Offset 0x4C 0x00 AD9380 OUTLINE DIMENSIONS 16.00 BSC SQ 1.60 MAX 0.75 0.60 0.45 100 1 76 75 PIN 1 14.00 BSC SQ TOP VIEW (PINS DOWN) 1.45 1.40 1.35 0.15 0.05 SEATING PLANE 0.20 0.09 7 3.5 0 0.08 MAX COPLANARITY 25 51 50 26 VIEW A 0.50 BSC LEAD PITCH VIEW A ROTATED 90 CCW 0.27 0.22 0.17 COMPLIANT TO JEDEC STANDARDS MS-026-BED Figure 19. 100-Lead Low Profile Quad Flat Package [LQFP] (ST-100) Dimensions shown in millimeters ORDERING GUIDE Model AD9380KSTZ-100 1 AD9380KSTZ-1501 AD9380/PCB 1 Max Speed (MHz) Analog Digital 100 100 150 150 Temperature Range 0C to 70C 0C to 70C Package Description 100-Lead Low Profile Quad Flat Package (LQFP) 100-Lead Low Profile Quad Flat Package (LQFP) Evaluation Board Z = Pb-free part. Rev. 0 | Page 59 of 60 Package Option ST-100 ST-100 NOTES (c) 2005 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D05688-0-10/05(0) Rev. 0 | Page 60 of 60