Manual Edition 06/2003 LOGO! The following supplement is part of this documentation: No. Designation Drawing number Edition 1 Product information A5E00324307-01 07/2004 4 019169 120982 @1P6ED1050-1AA00-0BE5@ 1P 6ED1050-1AA00-0BE5 Siemens AG Bereich Automation and Drives Geschaftsgebiet Industrial Automation Systems Postfach 4848, D-90327 Nuernberg Copyright: (c) Siemens AG 2001 - 2003 Subject to change without prior notice www.siemens.com/logo/ 6ED1050-1AA00-0BE5 Preface Dear customer We thank you for purchasing LOGO! and congratulate you on your decision. With LOGO! you have acquired a logic module that meets the stringent quality requirements of ISO 9001. LOGO! can be used in many fields of applications. Due to its high functionality and yet easy operation the LOGO! offers you highly efficient economies for almost any application. Purpose of this manual This LOGO! manual provides you with information about the creation of circuit programs, about the installation and use of LOGO! 0BA4 devices and expansion modules, and about their compatibility to the previous 0BA0-0BA3 versions (0BAx are the last four characters of the order number and differentiate the device series). LOGO!'s place in information technology The wiring information in your LOGO! manualis also found in the LOGO! Product Info included with all devices. For further information on programming the LOGO! on your PC, with the PC in the Online Help for LOGO!Soft Comfort. LOGO!Soft Comfort is the programming software for PCs. It runs under Windows, Linux, Mac OS X and helps you to get started with LOGO! and to write, test, print out and archive your programs, independent of the LOGO! . Guide We have divided this manual into 9 chapters: Getting started with LOGO! LOGO! installation and wiring Programming LOGO! LOGO! functions Configuring LOGO! LOGO! program module (card) LOGO! software Applications Appendix LOGO! Manual A5E00228550-01 i Preface Valid range of this manual The manual applies to devices of the series 0BA4. Changes compared to previous releases of the manual LOGO! 24o was added. The digital module LOGO! DM 8 24R was added. The analog module LOGO! AM 2 PT100 was added. Description of changes and new features of the series 0BA4 devices. Main differences compared to previous devices (0BA0 to 0BA3) Higher performance: faster execution times New program module (card) with more memory and know-how protection, selectable at the parameters. Display with background lighting and 4 x 12 characters. New features of the current devices (0BA4) You have 130 blocks available for creating the circuit program. You can select retentivity also for time functions. You can use the LOGO! cursor keys as inputs. You can use the special functions "Shift register", "Analog amplifier", "Analog value monitoring" and "Analog differential trigger". You can invert individual inputs. Six of the basic functions are expanded with four inputs. You can test your circuit program online using the PC. Parameters for certain functions can also be derived from analog values and counter values. Counter: You can also use fast inputs (I5, I6). Additional support At our Internet address http://www.siemens.com/logo you can quickly and easily find answers to your queries about LOGO!. You can reach Technical Support under: Phone: +49 (0)180 5050-222 Fax: +49 (0)180 5050-223 E-Mail: adsupport@siemens.com ii LOGO! Manual A5E00228550-01 Preface Safety guidelines The notes in this user manual are for your own personal safety and for preventing damage to assets. You should read them carefully and follow the instructions they give you. These notes are highlighted with a warning triangle and are shown according to the degree of hazard as follows: ! Danger Warns that death, serious harm to health or damage to assets will result if the respective precautionary measures are not taken. ! Warning Warns that death, serious harm to health or damage to can result if the respective precautionary measures are not taken. ! Caution Warns that harm to health or damage to assets can result if the respective precautionary measures are not taken. Caution Means that material damage may occur if corresponding safety measures are not taken. Note Draws your attention to particularly important information relating to the product and its handling, or to a part of the documentation requiring your special attention. Qualified personnel Only skilled personnel should be allowed to start and operate this device. Qualified personnel in the sense of the information on safety technology in this manual are persons who are authorized to commission, to ground and to tag circuits, equipment and systems in accordance with safety regulations and standards. LOGO! Manual A5E00228550-01 iii Preface Use as intended Please note: ! Warning This device must always be used as intended for the applications described in the catalog and in the technical specifications, and only in combination with third-party devices or components approved or recommended by Siemens. Prerequisite for the safe and proper operation of the product is its proper transportation, storage, installation and mounting, and careful operator control and maintenance. Trademarks LOGO! is a trademark of SIEMENS AG . Other designations in this documentation may represent trademarks, whose use by third parties for their own purpose my infringe the right of the owner. Copyright Siemens AG 1996 to 2003 All rights reserved The reproduction, distribution or use of this document or its contents is not permitted without express written authority. Offenders will be liable for damages. All rights reserved, especially for the granting of patents or GM entries. Disclaimer of liability We have examined the contents of this publication for agreement with the hardware and software described. Nevertheless, discrepancies can not be ruled out. Any liability and warranty for the accuracy of this information is excluded. The data in this manual are reviewed at regular intervals. Any corrections required are included in the subsequent editions. Suggestions for improvement are welcomed. iv LOGO! Manual A5E00228550-01 Contents Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i 1 Getting started with LOGO! . . . . . . . 1 2 LOGO! installation and wiring . . . . . 11 2.1 2.1.1 2.1.2 2.2 2.2.1 2.2.2 2.3 2.3.1 2.3.2 2.3.3 2.4 Setup of the modular LOGO! . . . . . . . . . . . . . . . . . . . Maximum setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Setup with different voltage classes . . . . . . . . . . . . . Installing/removing LOGO! . . . . . . . . . . . . . . . . . . . . DIN rail mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wall-mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wiring the LOGO! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connecting the power supply . . . . . . . . . . . . . . . . . . . Connecting LOGO! inputs . . . . . . . . . . . . . . . . . . . . . . Connecting outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . Switching on the LOGO!/Power On . . . . . . . . . . . . . 13 13 14 16 17 21 23 23 25 31 33 3 Programming LOGO! . . . . . . . . . . . . 37 3.1 3.2 3.3 Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Blocks and block numbers . . . . . . . . . . . . . . . . . . . . . The way to LOGO!, starting with the circuit diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . The 4 Golden rules for the operation of LOGO! . . Overview of the LOGO! menus . . . . . . . . . . . . . . . . . Writing and starting the circuit program . . . . . . . . . Select programming mode . . . . . . . . . . . . . . . . . . . . . The first circuit program . . . . . . . . . . . . . . . . . . . . . . . . Circuit program input . . . . . . . . . . . . . . . . . . . . . . . . . . Assigning a circuit program name . . . . . . . . . . . . . . . Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Switching LOGO! to RUN mode . . . . . . . . . . . . . . . . Second circuit program . . . . . . . . . . . . . . . . . . . . . . . . Deleting a block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 42 3.4 3.5 3.6 3.6.1 3.6.2 3.6.3 3.6.4 3.6.5 3.6.6 3.6.7 3.6.8 LOGO! Manual A5E00228550-01 45 48 50 51 51 53 54 60 61 66 68 74 v Contents 3.6.9 Deleting block groups . . . . . . . . . . . . . . . . . . . . . . . . . 3.6.10 Correcting typing errors . . . . . . . . . . . . . . . . . . . . . . . . 3.6.11 Deleting the circuit program . . . . . . . . . . . . . . . . . . . . 3.6.12 Summertime/wintertime conversion . . . . . . . . . . . . . 3.6.13 Synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.7 Memory space and circuit dimensions . . . . . . . . . . 4 75 76 77 78 83 84 LOGO! functions . . . . . . . . . . . . . . . . . 89 4.1 Constants and connectors - Co . . . . . . . . . . . . . . . . 4.2 Basic functions list - GF . . . . . . . . . . . . . . . . . . . . . . . 4.2.1 AND (AND) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2.2 AND with edge evaluation . . . . . . . . . . . . . . . . . . . . . . 4.2.3 NAND (NOT AND) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2.4 NAND with edge evaluation . . . . . . . . . . . . . . . . . . . . 4.2.5 OR (OR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2.6 NOR (NOT OR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2.7 XOR (exclusive OR) . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2.8 NOT (Negation, Inverter) . . . . . . . . . . . . . . . . . . . . . . . 4.3 Basics on special functions . . . . . . . . . . . . . . . . . . . . 4.3.1 Designation of the inputs . . . . . . . . . . . . . . . . . . . . . . . 4.3.2 Time response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3.3 Backup of the real-time clock . . . . . . . . . . . . . . . . . . . 4.3.4 Retentivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3.5 Parameter protection . . . . . . . . . . . . . . . . . . . . . . . . . . 4.3.6 Calculating the gain and offset of analog values . . 4.4 Special functions list - SF . . . . . . . . . . . . . . . . . . . . . 4.4.1 On-delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4.2 Off-delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4.3 On-/Off-delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4.4 Retentive on-delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4.5 Wiping relay (pulse output) . . . . . . . . . . . . . . . . . . . . . 4.4.6 Edge triggered wiping relay . . . . . . . . . . . . . . . . . . . . 4.4.7 Asynchronous pulse generator . . . . . . . . . . . . . . . . . 4.4.8 Random generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4.9 Stairway lighting switch . . . . . . . . . . . . . . . . . . . . . . . . 4.4.10 Multiple function switch . . . . . . . . . . . . . . . . . . . . . . . . 4.4.11 Weekly timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4.12 Yearly timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.4.13 Up/down counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 93 95 96 97 98 99 100 101 101 102 103 104 105 105 106 106 109 113 117 119 121 123 125 128 130 132 135 138 143 146 vi LOGO! Manual A5E00228550-01 Contents 4.4.14 4.4.15 4.4.16 4.4.17 4.4.18 4.4.19 4.4.20 4.4.21 4.4.22 4.4.23 4.4.24 4.4.25 Hours counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Threshold trigger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Analog threshold trigger . . . . . . . . . . . . . . . . . . . . . . . Analog differential trigger . . . . . . . . . . . . . . . . . . . . . . Analog comparator . . . . . . . . . . . . . . . . . . . . . . . . . . . . Analog value monitoring . . . . . . . . . . . . . . . . . . . . . . . Analog amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Latching relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pulse relay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Message texts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Softkey . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Shift register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 155 158 161 165 170 173 175 176 179 186 190 Configuring LOGO! . . . . . . . . . . . . . . . 193 5.1 Selecting parameter assignment mode . . . . . . . . . . 5.1.1 Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.1.2 Selecting the parameters . . . . . . . . . . . . . . . . . . . . . . 5.1.3 Modifying parameters . . . . . . . . . . . . . . . . . . . . . . . . . 5.2 Setting the time-of-day and date (LOGO! ... C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194 196 197 198 5 201 6 LOGO! program module (card) . . . . 203 6.1 6.2 Security function (CopyProtect) . . . . . . . . . . . . . . . . Inserting and removing the program module (card) . . . . . . . . . . . . . . . . . . . . . Copying data from the LOGO! to the program module (card) . . . . . . . . . . . . . . . . . . Copying data from the program module (card) to LOGO! . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205 212 7 LOGO! Software . . . . . . . . . . . . . . . . . 215 7.1 Connecting the LOGO! to a PC . . . . . . . . . . . . . . . . . 218 6.3 6.4 LOGO! Manual A5E00228550-01 208 210 vii Contents 8 Applications . . . . . . . . . . . . . . . . . . . . . 221 8.1 8.1.1 8.1.2 8.1.3 8.1.4 8.2 8.2.1 8.2.2 8.2.3 8.2.4 8.2.5 8.3 8.3.1 8.3.2 8.4 8.4.1 8.4.2 8.4.3 8.5 Stairway or corridor lighting . . . . . . . . . . . . . . . . . . . Requirements for a stairway lighting system . . . . . . Previous solution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Lighting system with LOGO! . . . . . . . . . . . . . . . . . . . . Special features and expansion options . . . . . . . . . . Automatic door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Requirements of an automatic door . . . . . . . . . . . . . Conventional solution . . . . . . . . . . . . . . . . . . . . . . . . . Door control system with LOGO! . . . . . . . . . . . . . . . . Special features and expansion options . . . . . . . . . . Extended solution with LOGO! 230RC . . . . . . . . . . . Air-conditioning System . . . . . . . . . . . . . . . . . . . . . . . Requirements for an air-conditioning System . . . . . Advantages of using LOGO! . . . . . . . . . . . . . . . . . . . . Factory door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Requirements for a gate control system . . . . . . . . . . Previous solution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Extended LOGO! solution . . . . . . . . . . . . . . . . . . . . . . Centralized control and monitoring of several factory doors . . . . . . . . . . . . . . . . . . . . . . . . Requirements for a gate control system . . . . . . . . . . Luminous rows . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Requirements for a lighting system . . . . . . . . . . . . . . Previous solution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Luminous row control system with LOGO! 230RC . Service water pump . . . . . . . . . . . . . . . . . . . . . . . . . . . Requirements for a control system of a service water pump . . . . . . . . . . . . . . . . . . . . . . . Previous solution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Service water pump system with LOGO! 230RC . . Special features and expansions . . . . . . . . . . . . . . . . Further fields of application . . . . . . . . . . . . . . . . . . . 223 223 223 224 226 227 227 228 228 231 231 234 234 237 239 239 240 242 8.5.1 8.6 8.6.1 8.6.2 8.6.3 8.7 8.7.1 8.7.2 8.7.3 8.7.4 8.8 viii 243 244 247 247 248 249 251 252 252 253 254 255 LOGO! Manual A5E00228550-01 Contents Appendix A Technical data . . . . . . . . . . . . . . . . . . . 259 General technical data . . . . . . . . . . . . . . . . . . . . . . . . . Technical data: LOGO! 230... and LOGO! DM8 230R . . . . . . . . . . . . . . . . . . . . . . . . . A.3 Technical data: LOGO! 24... and LOGO! DM8 24 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A.4 Technical data: LOGO! 24RC... and LOGO! DM8 24 R . . . . . . . . . . . . . . . . . . . . . . . . . A.5 Technical data: LOGO! 12/24... and LOGO! DM8 12/24R . . . . . . . . . . . . . . . . . . . . . . . . . . . . A.6 Switching capacity and service life of the relay outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . A.7 Technical data: LOGO! AM 2 . . . . . . . . . . . . . . . . . . . A.8 Technical data: LOGO! AM 2 PT100 . . . . . . . . . . . . . A.9 Technical data: LOGO!Power 12 V . . . . . . . . . . . . . . A.10 Technical data: LOGO!Power 24 V . . . . . . . . . . . . . . A.11 Technical data: LOGO! Contact 24/230 . . . . . . . . . . 259 A.1 A.2 261 264 267 270 273 274 275 277 279 281 B Determining the cycle time . . . . . . . . 283 C LOGO! without display . . . . . . . . . . . 285 D LOGO! menu structure . . . . . . . . . . . 289 E Order numbers . . . . . . . . . . . . . . . . . . . 291 F Abbreviations . . . . . . . . . . . . . . . . . . . . 293 Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . 295 LOGO! Manual A5E00228550-01 ix Contents x LOGO! Manual A5E00228550-01 1 Getting started with LOGO! Here's LOGO! LOGO! is a universal logic module made by Siemens. LOGO! integrates Controls Operator and display panel with background lighting Power supply Interface for expansion modules Interface for the program module (card) and a PC cable Pre-configured standard functions, e.g. on- and off-delays, pulse relay and softkey Timer Digital and analog flags Inputs and outputs, according to the device type. What LOGO! can do for you LOGO! offers solutions for domestic and installation engineering (e.g. for stairway lighting, external lighting, sun blinds, shutters, shop window lighting etc.), switch cabinet engineering, as well as for mechanical and apparatus engineering (e.g. for gate control systems, air-conditioning systems, or rainwater pumps etc.). LOGO! can also be implemented for special control systems in conservatories or greenhouses, for control signal processing and, by connecting a communication module (e.g. ASi) for distributed local controlling of machines and processes. Special versions without operator panel and display unit are available for series production applications in small machine, apparatus, switching cabinet and installation engineering. LOGO! Manual A5E00228550-01 1 Getting started with LOGO! Which devices are available? LOGO! Basic is available in two voltage classes: Class 1 24 V, i.e. 12 V DC, 24 V DC, 24 V AC Class 2 > 24 V, i.e. 115...240 V AC/DC, in the versions: With display: 8 inputs and 4 outputs. Without display ("LOGO! Pure"): 8 inputs and 4 outputs. Each version is integrated into 4 subunits (SU), is equipped with an expansion interface and provides 33 pre-configured standard and special function blocks for the creation of your circuit program. Which expansion modules are available? LOGO! digital modules are available for operation with 12 V DC, 24 V AC/DC and 115...240 V AC/DC, and are equipped with four inputs and four outputs. LOGO! analog modules are available for operation with 12 V DC and 24 V DC, and are equipped with two analog inputs or two Pt100 inputs. LOGO! communications modules (CM), for example the communications module AS interface, that is described in a separate documentation. The digital/analog modules are integrated in two subunits. Each one is equipped with two expansion interfaces for connecting additional modules. Devices no longer available All versions with 6 inputs. A long variant with 12 inputs and 8 outputs The bus version with 12 inputs and 8 outputs. The modular features of LOGO! replace this type of equipment. It's your choice The various LOGO! Basic versions and expansion modules offer you a highly flexible and adaptive system to suit your specific tasks. 2 LOGO! Manual A5E00228550-01 Getting started with LOGO! The LOGO! system offers you many solutions such as for small domestic installations, simple automation tasks, and even complex engineering tasks involving its integration into a bus system (e.g. communications module AS interface). Note LOGO! Basic may only be equipped with expansion modules of the same voltage class. Mechanical encoding pins in the housing prevent you from connecting devices of a different voltage class. Exception: The left-hand interface of an analog module or communication module is galvanically isolated. This type of expansion module can therefore be connected to devices of a different voltage class. See also Chapter 2.1. Each LOGO! Basic provides the following connections for the creation of the circuit program, regardless of the number of connected modules: Digital inputs I1 to I24 Analog inputs AI1 to AI8 Digital outputs Q1 to Q16 Analog outputs AQ1 and AQ2 Digital flag blocks M1 to M24, M8: Startup flag Analog flag blocks AM1 to AM6 Shift register bits S1 to S8 4 cursor keys 16 blank outputs X1 to X16. LOGO! Manual A5E00228550-01 3 Getting started with LOGO! The LOGO! structure 2 10 LOGO! Basic (e.g.: 230 RC) 1 8 I1 I2 I3 I4 I5 I6 I7 I8 4 L1 N 4 90 35 6 5 1 Q1 2 1 Q2 2 1 2 Q3 1 2 Q4 3 72 55 2 9 8 10 1 8 4 L1 N I1 I2 I3 I4 11 (e.g.: DM8 230R) RUN/STOP 1 Q1 2 1 1 Q3 2 Q2 90 7 35 LOGO! expansion module 9 2 1 Q42 3 36 1 Power supply 2 Inputs 3 Outputs 4 Module slot with cap 4 53 5 Control panel (not for RCo) 8 Expansion interface 6 LCD (not for RCo) 9 Mechanical coding pins 7 RUN/STOP indicator 10 Mechanical coding sockets 11 Slide LOGO! Manual A5E00228550-01 Getting started with LOGO! LOGO! Basic (e.g.: 12/24 RC) 2 10 1 8 4 L+ M I1 I2 I3 I4 I5 I6 I7 I8 4 90 35 6 5 1 Q1 2 1 Q2 2 1 2 Q3 1 2 Q4 3 72 55 2 8 10 1 9 8 4 L+ M I1 I2 I3 I4 (e.g.: DM8 12/24R) 11 7 1 90 RUN/STOP 35 LOGO! expansion module 9 2 1 2 Q1 Q2 1 Q3 2 1 Q42 3 53 36 1 Power supply 2 Inputs 3 Outputs 4 Module slot with cap LOGO! Manual A5E00228550-01 5 Control panel (not for RCo) 8 Expansion interface 6 LCD (not for RCo) 9 Mechanical coding pins 7 RUN/STOP indicator 10 Mechanical coding sockets 11 Slide 5 Getting started with LOGO! LOGO! AM 2 9 10 1 9 8 L+ M 4 L+ M 8 11 90 RUN/STOP 35 7 12 PE INPUT2x(0..10V/0..20mA) I1 M1 U1 I2 M2 U2 2 53 36 1 Power supply 2 Inputs 7 RUN/STOP indicator 8 Expansion interface 9 Mechanical coding pins 10 Mechanical coding sockets 11 12 PE terminal, for connecting earth and the shielding of analog measuring cables. Slide LOGO! AM 2 PT100 10 9 1 9 8 L+ M 4 L+ M 8 11 90 RUN/STOP 1 35 7 12 PE M1+ IC1 M1- M2+IC2 M2- 2 53 36 6 1 Power supply 2 Inputs 7 RUN/STOP indicator 8 Expansion interface 9 Mechanical coding pins 10 Mechanical coding sockets 11 12 PE terminal, for connecting earth and the shielding of analog measuring cables. Slide LOGO! Manual A5E00228550-01 Getting started with LOGO! How to identify the LOGO! The LOGO! identifier informs you of various properties: 12: 12 V DC version 24: 24 V DC version 230: 115...240 V AC version R: Relay outputs (without R: solid-state outputs) C: Integrated Weekly timer o: Version without display ("LOGO! Pure") DM: Digital module AM: Analog module CM: Communications module (e.g. AS interface) Symbols Version with display unit is equipped with 8 inputs and 4 outputs Version without display unit is equipped with 8 inputs and 4 outputs The digital module is equipped with 4 digital inputs and 4 digital outputs The analog module is equipped with 2 analog inputs The communications module (CM) is equipped with 4 virtual inputs and 4 virtual outputs (e.g. AS interface) LOGO! Manual A5E00228550-01 7 Getting started with LOGO! Versions The following LOGO! versions are available: Symbol Designation LOGO! 12/24 RC LOGO! 24 Supply voltage Inputs 12/24 V DC 8 digital 24 V DC 8 digital (1) (1) Outputs Properties 4 relays (10 A) 4 solid state 24V / 0.3A no clock LOGO! 24RC (3) 24 V AC/ 24 V DC 8 digital 4 relays (10A) LOGO! 230RC (2) 115...240 V AC/DC 8 digital 4 relays (10A) LOGO! 12/24RCo 12/24 V DC 8 digital 4 relays (10A) no display unit 24 V DC 8 digital 4 solid state 24 V / 0.3A no display unit 4 relays (10A) no display unit 4 relays (10A) no display unit LOGO! 24o (1) (1) LOGO! 24RCo (3) LOGO! 230RCo (2) 24 V AC / 24 V DC 8 digital 115...240 V AC/DC 8 digital no keyboard no keyboard no clock no keyboard no keyboard (1): Of those can be used alternatively: 2 analog inputs (0 ... 10V) and 2 fast inputs. (2): 230 V AC versions: Two groups consisting of 4 inputs each. Each group must be connected to the same phase. It is possible to interconnect groups with a different phase. (3): The digital inputs can be operated with P or N action. 8 LOGO! Manual A5E00228550-01 Getting started with LOGO! Expansion modules The following expansion modules can be connected to the LOGO!: Symbol Name Power supply Inputs Outputs LOGO! DM 8 12/24R 12/24 V DC 4 digital 4 relays (5A) LOGO! DM 8 24 24 V DC 4 digital 4 solid state 24 V / 0.3 A LOGO! DM 8 24R (3) 24 V AC/DC 4 digital 4 relays (5A) LOGO! DM 8 230 R 115...240 V AC/DC 4 digital (1) 4 relays (5A) LOGO! AM 2 12/24 V DC 2 analog 0 ... 10 V or 0 ... 20 mA (2) none LOGO! AM 2 PT100 12/24 V DC 2 Pt100 -50 C to +200 C none (1): Different phases are not allowed within the inputs. (2): 0 ... 10 V, 0 ... 20 mA can be connected optionally. (3): Digital inputs can be operated either with P or with N action. Certification and approvals LOGO! is certified to cULus and FM. cULus Haz. Loc. Underwriters Laboratories Inc. (UL) to - UL 508 (Industrial Control Equipment) - CSA C22.2 No. 142 (Process Control Equipment) - UL 1604 (Hazardous Location) - CSA-213 (Hazardous Location) APPROVED for use in Class I, Division 2, Group A, B, C, D Tx Class I, Zone 2, Group IIC Tx FM Approval Factory Mutual Research (FM) to Approval Standard Class Number 3611, 3600, 3810 APPROVED for use in Class I, Division 2, Group A, B, C, D Tx Class I, Zone 2, Group IIC Tx LOGO! Manual A5E00228550-01 9 Getting started with LOGO! Note You will find current approvals on the rating plate of the relevant module. ! Warning Risk of personal injury and material damage. In potentially explosive atmospheres, there is a risk of personal injury or damage to material if you disconnect connectors when the system is in RUN. In potentially explosive atmospheres, always switch off the power supply to LOGO! and its components before you disconnect any connectors. LOGO! is issued with the CE Certificate of Conformity. It is compliant with VDE 0631 and IEC 61131-2 and interference-proof to EN 55011, Limit Class B. Marine certification has been requested. ABS (American Bureau of Shipping) BV (Bureau Veritas) DNV (Det Norske Veritas) GL (Germanischer Lloyd) LRS (Lloyds Register of Shipping) Class NK (Nippon Kaiji Kyokai) LOGO! is therefore suitable for use both in industry and in the domestic area. ID for Australia Our products carrying the label shown at the side are compliant with AS/NZS 2064:1997 (Class A) standard. Recycling and Disposal LOGO! units can be fully recycled, due to their low-pollutant equipment. Contact a certified electronic waste disposal center for environmentally acceptable recycling and disposal of your old devices. 10 LOGO! Manual A5E00228550-01 2 LOGO! installation and wiring General guidelines Please note the following guidelines for the installation and wiring of your LOGO! : Always ensure that the wiring of your LOGO! is compliant with current rules and standards. Also, conform with all national and regional regulations when you install and operate the devices. For information on standards and regulations that apply to your specific case, contact your local authorities. Always use cables with an appropriate conductor crosssections for the relevant current. You can wire the LOGO! with cable conductor cross-sections from 1.5 mm2 to 2.5 mm2; see Chapter 2.3. Do not exceed the screw torque of the terminals. The maximum torque is: 0.5 N/m, see Chapter 2.3. Keep the cabling as short as possible. If longer cables are necessary, you should use shielded versions. You should always route your cables in pairs: i.e. one neutral conductor plus one phase conductor or signal line. Always keep separate: - The AC wiring - High-voltage DC circuits with high-frequency switching cycles - Low-voltage signal wiring. Ensure that the wires are installed with an appropriate strain relief. Provide a suitable lightning surge arrester for cables installed in relevant areas of hazard. LOGO! Manual A5E00228550-01 11 LOGO! installation and wiring Do not connect an external power supply in parallel to the output load of a DC output. This could develop a reverse current at the output if you have not installed a diode or similar barrier device. Note LOGO! units may only be installed and wired by skilled personnel who know and follow the general engineering rules and the relevant regulations and standards. 12 LOGO! Manual A5E00228550-01 LOGO! installation and wiring 2.1 Setup of the modular LOGO! 2.1.1 Maximum setup Maximum setup of a LOGO! with analog inputs (LOGO! 12/24 RC/RCo and LOGO! 24/24o) LOGO! Basic, 4 digital modules and 3 analog modules I1......I6, I7, I8 AI1, AI2 LOGO! Basic Q1...Q4 I9...I12 I13...I16 I17...I20 I21...I24 AI3, AI4 AI5, AI6 AI7, AI8 LOGO! LOGO! LOGO! DM 8 DM 8 DM 8 LOGO! LOGO! LOGO! LOGO! DM 8 AM 2 AM 2 AM 2 Q5...Q8 Q9...Q12 Q13...Q16 Maximum setup of a LOGO! without analog inputs (LOGO! 24 RC/RCo and LOGO! 230 RC/RCo) LOGO! Basic, 4 digital modules and 4 analog modules I1 . . . . . . . . . . . I8 I9...I12 I13...I16 I17...I20 I21...I24 AI1 , AI2 AI3, AI4 AI5, AI6 AI7, AI8 LOGO! Basic Q1...Q4 LOGO! LOGO! LOGO! LOGO! LOGO! LOGO! LOGO! LOGO! DM 8 DM 8 DM 8 DM 8 AM 2 AM 2 AM 2 AM 2 Q5...Q8 Q9...Q12 Q13... Q16 High-speed/optimal communication performance For optimal and high-speed communication performance between LOGO! Basic and the various modules, we recommend you install the "digital modules first, then the analog modules" (example above). LOGO! Manual A5E00228550-01 13 LOGO! installation and wiring 2.1.2 Setup with different voltage classes Rules Digital modules can only be connected to devices of the same voltage class. You may connect analog and communications modules to devices of any voltage class. Overview: Connecting an expansion module to LOGO! Basic LOGO! B i Basic Expansion modules DM 8 DM 8 DM 8 DM 8 AM2/ 12/24R 24 24R 230R AM2 CM PT100 LOGO! 12/24 RC x x x - x x LOGO! 24 x x x - x x LOGO! 24 RC x x x - x x LOGO! 230 RC - - - x x x LOGO! 12/24RCo x x x - x x LOGO! 24o x x x - x x LOGO! 24 RCo x x x - x x LOGO! 230 RCo - - - x x x 14 LOGO! Manual A5E00228550-01 LOGO! installation and wiring Overview: Connecting a further expansion module to an expansion module Expansion module d l Further expansion modules DM 8 DM 8 DM 8 DM 8 AM2/ 12/24R 24 24R 230R AM2 CM PT100 DM 8 12/24 R x x x - x x DM 8 24 x x x - x x DM 8 24 R x x x - x x DM 8 230 R - - - x x x AM2 / AM2 PT100 x x x - x x CM AS interface x x x - x x LOGO! Manual A5E00228550-01 15 LOGO! installation and wiring 2.2 Installing/removing LOGO! Dimensions The LOGO! installation dimensions are compliant with DIN 43880. LOGO! can be snap-mounted to 35 mm DIN rails to EN 50022 or on the wall. LOGO! width: LOGO! Basic has a width of 72 mm, which corresponds with 4 subunits. LOGO! expansion modules have a width of 36 mm, which corresponds with 2 subunits. Note The figure below shows you an example of the installation and removal of a LOGO! 230 RC and a digital module. The measures shown apply to all other LOGO! Basic versions and expansion modules. ! 16 Warning Always switch off power before you "remove" and "insert" an expansion module. LOGO! Manual A5E00228550-01 LOGO! installation and wiring 2.2.1 DIN rail mounting Mounting How to mount a LOGO! Basic and a digital module onto a DIN rail: LOGO! Basic: 1. Hook the LOGO! Basic module onto the rail and 2. then push down the lower end to snap it on. The mounting interlock at the rear must engage 6 1 3 5 2 4 LOGO! digital module: 3. On the right side of the LOGO! Basic/LOGO! expansion module, remove the connector cap 4. Place the digital module onto the DIN rail on the righthand side of the LOGO! Basic 5. Slide the digital module towards the left until it contacts the LOGO! Basic LOGO! Manual A5E00228550-01 17 LOGO! installation and wiring 6. Using a screwdriver, push the interlock to the left. In its end position the slide interlock engages in the LOGO! Basic. Repeat steps 3 through 6 to mount further expansion modules. Note The expansion interface on the last expansion module must be covered. 18 LOGO! Manual A5E00228550-01 LOGO! installation and wiring Removal To remove the LOGO!: ....... if you have installed only one LOGO! Basic: Part A 1. Insert a screwdriver into the eyelet at the bottom of the slide interlock and move the latch downward 2. Swing the LOGO! Basic off the DIN rail. 1 2 2 4 1 LOGO! Manual A5E00228550-01 3 A B 19 LOGO! installation and wiring ....... if you have connected at least one expansion module to the LOGO! Basic: Part B 1. Using a screwdriver, push the integrate slide interlock to the right 2. Slide the expansion module off towards the right 3. Insert a screwdriver into the eyelet at the bottom of the slide interlock and lever it downward 4. Swing the expansion module off the profile rail. Repeat steps 1 to 4 for all other expansion modules. Note If you have connected more than one expansion module, it is advisable to start removal with the last module at the right-hand side. Make sure that the slide interlock of the module to be installed/removed is not engaged in the next module. 20 LOGO! Manual A5E00228550-01 LOGO! installation and wiring 2.2.2 Wall-mounting For wall-mounting, first slide the mounting slides on the rear side of the devices towards the outside. You can now wall-mount the LOGO! by means of two mounting slides and two M4 screws (tightening torque 0.8 to 1.2 N/m). Mounting slides LOGO! Manual A5E00228550-01 21 LOGO! installation and wiring Drilling template for wall-mounting Before you can wall-mount the LOGO!, you need to drill holes using the template shown below. 35.5 +/- 0.2 98 +/- 0.3 53.5 +/- 0.2 1 2 2 2 n x 35.5 +/- 0.2 All dimensions in mm Bore hole for M4 screw Tightening torque 0.8 to 1.2 N/m 1 LOGO! Basic LOGO! expansion module 2 22 LOGO! Manual A5E00228550-01 LOGO! installation and wiring 2.3 Wiring the LOGO! Wire the LOGO! using a screwdriver with a 3-mm blade. You do not need wire ferrules for the terminals. Permitted conductor cross-sections: 1 x 2.5 mm2 2 x 1.5 mm2 for each second terminal chamber Tightening torque: 0.4...0.5 N/m or 3...4 lbs/in Note Always cover the terminals after you have completed the installation. To protect LOGO! adequately from impermissible contact to live parts, local standards must be complied with. 2.3.1 Connecting the power supply The 230-V versions of LOGO! are suitable for operation with rated voltages of 115 V AC/DC and 240 V AC/DC. The LOGO! 24-V and 12-V versions can be operated with a 24 VDC, 24 V AC or 12 VDC power supply. For information on permissible voltage tolerances, line frequencies and power consumption, refer to the installation instructions in the Product Information supplied with your device and to the technical data in Appendix A. Note A power failure may cause an additional edge triggering signal at the special functions, for example. Data of the last uninterrupted cycle are stored in LOGO!. LOGO! Manual A5E00228550-01 23 LOGO! installation and wiring Connecting LOGO! To connect LOGO! to the power supply: LOGO! ..... with AC power supply LOGO! ..... with DC power supply L+ M L1 N L+ M I1 I2 I3 I4 I5 Protection with safety fuse if required (recommended) for: 12/24 RC...: 0.8 A 24: 2.0 A L1 N I1 I2 I3 I4 To suppress surge voltages, install varistors (MOV) with an operating voltage at least 20 % above the rated voltage. Note LOGO! is a double-insulated switchgear. It is not required to connect an equipment grounding conductor. Circuit protection with AC voltage To suppress voltage peaks on the power supply lines, you can install a metal oxide varistor (MOV) (MOV). Make sure that the operating voltage of the varistor (MOV) used lies at least 20 % above the rated voltage (for example S10K275). 24 LOGO! Manual A5E00228550-01 LOGO! installation and wiring 2.3.2 Connecting LOGO! inputs Requirements At the inputs you connect sensor elements such as: momentary switches, switches, light barriers, daylight control switches etc. Sensor characteristics for LOGO! LOGO! 12/24 RC/RCo LOGO! DM8 12/24 R I1 ... I6 I7, I8 LOGO! 24/24o LOGO! DM8 24 I1 ... I6 I7, I8 Signal status 0 < 5 VDC < 5 VDC < 5 VDC < 5 VDC Input current < 1.0 mA < 0.05 mA < 1.0 mA < 0.05 mA Signal status 1 > 8 V DC > 8 V DC > 8 V DC > 8 V DC Input current > 1.5 mA > 0.1 mA > 1.5 mA > 0.1 mA LOGO! 24 RC/RCo (AC) LOGO! DM8 24 R (AC) LOGO! 24 RC/RCo (DC) LOGO! DM8 24 R (DC) LOGO! 230 RC/RCo (AC) LOGO! DM8 230 R (AC) LOGO! 230 RC/RCo (DC) LOGO! DM8 230 R (DC) Signal status 0 < 5 V AC < 5 V DC < 40 V AC < 30 V DC Input current < 1.0 mA < 1.0 mA < 003 mA < 003 mA Signal status 1 > 12 V AC > 12 V DC > 79 V AC > 79 V DC Input current > 2.5 mA > 2.5 mA > 0.08 mA > 0.08 mA Note The digital inputs of LOGO! 230 RC/RCo are divided into two groups, each consisting of four inputs. Within the same group, all inputs must be operated on the same phase. Different phases are only possible between the groups. Example: I1 to I4 on phase L1, I5 to I8 on phase L2. Inputs within the LOGO! DM8 230R may not be connected to different phases. LOGO! Manual A5E00228550-01 25 LOGO! installation and wiring Sensor connections Connecting glow lamps and 2-wire proximity switches (Bero) to LOGO! 230 RC/230 RCo or LOGO! DM8 230 R (AC) L1 N Order number for C: Siemens Switchgear & Systems C L1 3SB1420-3D N X-capacitor 2.5 kV, 100 nF Take the quiescent current of any 2-wire proximity switches used into account. The level of the quiescent current of some 2-wire proximity switches is high enough to trigger a logical "1" signal at the LOGO! input. You should therefore compare the quiescent current of the proximity switches with the technical data of inputs Appendix A. 26 LOGO! Manual A5E00228550-01 LOGO! installation and wiring Restrictions Signal status transitions 0 1 / 1 0 After a 0 to 1 or 1 to 0 transition, the signal must remain constant at the input at least for the duration of one program cycle, so that LOGO! can detect the new signal status. The program execution time is determined by the size of the circuit program. Appendix B contains a benchmark test routine that you can use to determine the current scan cycle time. Special features of LOGO! 12/24 RC/RCo and LOGO! 24/24o High-speed inputs: I5 and I6 These versions are also equipped with high-speed counting inputs (Up/down counters, Threshold triggers). The restrictions mentioned earlier do not apply to these high-speed inputs. Note The high-speed inputs I5 and I6 are the same as in the previous versions 0BA0 to 0BA3, i.e. a circuit program that is written in these versions can be transferred to the new 0BA4 units by means of the programming software LOGO! SoftComfort, without any changes to these features. In contrast to this, you need to modify circuit programs written for a LOGO!...L version (high-speed inputs I11/I12). Expansion modules do not have high-speed inputs. Analog inputs: I7 and I8 The inputs I7 and I8 of LOGO! versions 12/24RC/RCo and 24/24o can be used both as standard digital inputs and as analog inputs. The input mode is defined in the LOGO! circuit program. The inputs I7 / I8 provide digital functions, and the inputs AI1 and AI2 provide analog functions. See also Chapter 4.1. LOGO! Manual A5E00228550-01 27 LOGO! installation and wiring Note The LOGO! AM 2 expansion module provides further analog inputs. The LOGO! AM 2 PT100 expansion module provides Pt100 inputs. Always use twisted and shielded cables for analog signals, and keep these as short as possible. Sensor connections To connect sensors to the LOGO! : LOGO! 12/24 .... The inputs of these devices not isolated and therefore require a common reference potential (chassis ground ). L+ M L+ M I1 I2 I3 I4 I5 At the LOGO! 12/24RC/RCo and LOGO! 24/24o modules, you can tap analog signals between the supply voltage and chassis ground. I8 LOGO! 230 .... L3 L2 L1 N L1 N 28 I1 I2 I3 I4 I5 I6 The inputs of these devices are arranged in 2 groups, each consisting of 4 inputs. Different phases are only possible between blocks, but not within the blocks. LOGO! Manual A5E00228550-01 LOGO! installation and wiring Warning ! Current safety regulations (VDE 0110, ... and IEC 61131-2, ... as well as cULus) do not permit the connection of different phases to an AC input group (I1 to I4 or I5 to I8) or to the inputs of a digital module. LOGO! AM 2 L + M PE L+ M L+ M PE terminal for connecting earth and the shielding of the analog measuring cable 1 Earth 2 Cable shielding 3 3 DIN rail RUN/STOP 1 PE M L + Current 0...20 mA I1 M1 U1 I2 M2 U2 2 Reference current M Current measurement LOGO! Manual A5E00228550-01 Voltage measurement 29 LOGO! installation and wiring LOGO! AM 2 PT100 You can connect either a 2- or 3-wire Pt100 resistive thermocouple to the module. For a 2-wire connection, you need to short-circuit terminals M1+ and IC1 or M2+ and IC2. Errors caused by the ohmic resistance of the measuring line are not compensated with this type of connection. A line resistance of 1 is proportional to a measuring error of +2.5C. A 3-wire technique suppresses the influence of the cable length (ohmic resistance) on the result of the measurement. 2-wire technique L+ M L+ M 3-wire technique L+ M L+ M RUN/ STOP RUN/ STOP PE PE M1+ IC1 M1- M2+ IC2 M2- Pt100 M1+ IC1 M1- M2+ IC2 M2- Pt100 Note When you operate the LOGO! AM 2 PT100 expansion module on an ungrounded (floating potential) power supply, the indicated temperature value may be subject to heavy fluctuation. In this case, connect the shielding of the thermocouple cable to the negative output / chassis ground output of the power supply module. 30 LOGO! Manual A5E00228550-01 LOGO! installation and wiring 2.3.3 Connecting outputs LOGO! ...R... The LOGO! ...R... version is equipped with relay outputs. The potential of the relay contacts is isolated from the power supply and the inputs. Requirements for relay outputs You can connect various loads to the outputs, e.g. lamps, fluorescent lamps, motors, contactor relays etc. For information on the properties required for the loads connected to the LOGO! ...R..., refer to Appendix A. Connecting This is how you connect the load to LOGO! ...R...: DM8...R 1 Q5 2 1 Q1 2 1 Load Q2 1 Q6 2 2 Load Protection with automatic circuit-breaker, max. 16 A, characteristics B16, e.g.: Power circuit-breaker 5SX2 116-6 (if required) LOGO! Manual A5E00228550-01 31 LOGO! installation and wiring LOGO! with solid-state outputs LOGO! versions with solid-state outputs can be identified by the fact that the letter R is missing from their type name. The outputs are short circuit-proof and overload-proof. An auxiliary load voltage supply is not necessary, because LOGO! supplies the load voltage. Requirements for solid-state outputs The load connected to LOGO! must have the following characteristics: The maximum switched current is 0.3 A per output. Connecting This is how you connect the load to a LOGO! with solidstate outputs: DM8 24 Q5 M Q1 M Q6 M Q2 M Load Load Load: 24 V DC, 0.3 A max. 32 LOGO! Manual A5E00228550-01 LOGO! installation and wiring 2.4 Switching on the LOGO!/Power On LOGO! does not have a power switch. The reaction of LOGO! during startup depends on Whether a circuit program is stored in LOGO! Whether a program module (Card) is inserted Whether this is a LOGO! version without display unit (LOGO!...o) The status of LOGO! at the time of power failure. All possible reaction of LOGO! are described on the following page. LOGO! Manual A5E00228550-01 33 LOGO! installation and wiring Before power off No Program Press ESC After power on or No program Press ESC (empty) No program in memory (with program) Mo 09:00 2003-01-27 I: or 0.. 123456789 1..0123456789 2..01234 Q: (empty) B3: Par = 0300 = 0028 (with program) B1 & Q1 Program in memory or 0.. 123456789 1..0123456789 2..01234 Mo 09:00 2002-01-31 I: 0.. 123456789 1..0123456789 2..01234 With stored program from LOGO! ...... with a program copied from the program module (Card) in LOGO! ...... >Program.. Card.. Clock.. Start with stored program from LOGO! >Program.. Card.. Clock.. Start with program copied from the program modul (Card) in LOGO! (empty) (with program) 34 Mo 09:00 09:00 2002-01-31 I: LOGO! in RUN mode 0.. 12345678 9 1..0123456 LOGO! in RUN mode Cnt >Program.. Card.. Clock.. Start LOGO! Manual A5E00228550-01 LOGO! installation and wiring You can also memorize four simple rules for starting LOGO! : 1. If neither the LOGO! nor the inserted program module (Card) contains a circuit program, the LOGO! (with display unit ) reports: 'No Program / Press ESC'. 2. A circuit program on the program module (Card) is automatically copied to LOGO!. The circuit program in the LOGO! is overwritten. 3. If there is a circuit program in LOGO! or on the program module (Card), LOGO! adopts the operational state it had prior to POWER-OFF. Versions without display unit (LOGO!...o) automatically change from STOP to RUN (LED changes from red to green). 4. If you have enabled retentivity at least for one function, or a function is permanently retentive, the current values are retained at POWER-OFF. Note When a power failure occurs while you are entering a circuit program, the program in LOGO! will be deleted after power is returned. Before you modify the circuit program, you should therefore save a backup copy of your original to a program module (Card) or to a computer (LOGO!Soft Comfort). LOGO! Manual A5E00228550-01 35 LOGO! installation and wiring LOGO! Basic operating states LOGO! Basic/Pure knows two operating states: STOP and RUN STOP RUN The display shows: Display: Screen mask for 'No Program' (not LOGO!...o) Switching LOGO! to programming mode (not LOGO!...o) monitoring I/Os and messages (after START in the main menu) (not LOGO!...o) Switching LOGO! to pa- LED is red rameter assignment mode (not LOGO!...o) (only LOGO!...o) LED is green (only LOGO!...o) Action of LOGO!: Action of LOGO!: The inputs data are not LOGO! reads the status of fetched. the inputs The circuit program is not executed The relay contacts are permanently open or the solidstate outputs are switched off LOGO! uses the circuit program to calculate the status of the outputs LOGO! switches the relay/ solid-state outputs on or off LOGO! expansion modules, operating states LOGO! expansion modules know three operating states: The LED is lit green, red or orange. LED is lit Green (RUN) The expansion module communicates with the device to its left 36 Red (STOP) The expansion module does not communicate with the device to its left Orange Initialization phase of the expansion module LOGO! Manual A5E00228550-01 3 Programming LOGO! Getting started with LOGO! Programming in our context refers to the creation of a circuit program. A LOGO! circuit program program is actually no more than a circuit diagram presented in a slightly different form! We have adapted this presentation to the LOGO! display field. In this chapter we are going to show you how to use LOGO! to create the LOGO! circuit programs for your application. At this point, we once again refer to LOGO!Soft Comfort, which is the LOGO! programming software you can use to quickly and easily create, test, modify save and print the circuit programs. The topics in this manual relate only to the creation of circuit programs on the actual LOGO!, because the programming software LOGO!Soft Comfort already contains an extensive Online Help. See also Chapter 7. Note LOGO! versions without display unit, i.e. the LOGO! 24o, LOGO! 12/24RCo, LOGO! 24RCo and LOGO! 230RCo units, do not have an operator panel and display unit. They are primarily designed for use in small machine and process equipment engineering systems for series production. LOGO!...o versions are not programmed directly at the unit. Instead, the circuit program is downloaded to this device by means of LOGO!Soft Comfort or program modules (Cards) of other LOGO! 0BA4 units. LOGO! versions without display can not write data to program modules (Cards). See Chapter 6, 7 and Appendix C. LOGO! Manual A5E00228550-01 37 Programming LOGO! A small example in the first part of this chapter introduces the operating principle of LOGO!. We shall first show you the meaning of two basic terms, namely the connector and the block. In the next step, we shall create a circuit program based on a simple conventional circuit, which you ... can enter directly in LOGO! in the third step. It will take you only a few pages of this manual store your first executable circuit program in the LOGO! unit. With a suitable hardware (switches etc.), you will then be able to carry out first tests. 38 LOGO! Manual A5E00228550-01 Programming LOGO! 3.1 Connectors The LOGO! is equipped with inputs and outputs Example of a configuration with several modules: Inputs L+ M I1 I2 I3 I4 I5 I6 AI1 AI2 L+ M I9 I10 I11I12 L+ M RUN/STOP L+ M L+ M I13I14I15 I16 RUN/STOP RUN/STOP PE 1 2 1 2 2Q6 Q5 1 Q1 2 1 Q2 2 1 2 Q3 1 2 Q4 Q7 Outputs 1 2 Q8 1INPUT 2x (..10 V/..20 mA) A!3 M3U3AI4M4 U4 1 1 Q9 2 Q11 2 1 1 2 Q10 2 Q12 Analog inputs Each input is identified by the letter I plus a number. When you take a look at the LOGO! from the front, you can see the input terminals at the top. Only the analog modules LOGO! AM 2 and AM 2 PT100 have the inputs at the bottom. Each output is identified by the letter Q plus a number. In the figure, you can see the output terminals at the bottom. LOGO! Manual A5E00228550-01 39 Programming LOGO! Note LOGO! can recognize, read and switch the I/O of all expansion modules, regardless of their type. The I/O are presented in the installation order of the modules. The following I/Os and flag blocks are available for the creation of your circuit program: : I1 to I24, AI1 to AI8, Q1 to Q16, AQ1 and AQ2, M1 to M24 and AM1 to AM6. Also available are the shift register bits S1 to S8, 4 cursor keys C , C , C and C , as well as 16 blank outputs X1 to X16. More details are found in Chapter 4.1. The following applies to the inputs I7 and I8 of LOGO! 12/24... and LOGO! 24/24o versions: If Ix is used in the circuit program, this input signal is digital; signals at AIx are analog. Input AIx can only represent the connector that is actually capable of handling analog signals. LOGO!'s connectors The term connector refers to all connections and states in LOGO! . The I/O status can be '0' or '1'. Status '0' means that the input does not carry a voltage. Status '1' means that the input carries voltage. We have introduced 'hi', 'lo' and 'x' connectors to make it easier for you to create the circuit program: 'hi' (high) is assigned the status '1', 'lo' (low) is assigned the status '0'. You do not have to use all the of connectors of a block. The circuit program automatically assigns the unused connectors a status that ensures proper functioning of the relevant block. If you prefer to do so, you can identify unused connectors with an 'x'. For information on the meaning of the term "block", refer to Chapter 3.2. 40 LOGO! Manual A5E00228550-01 Programming LOGO! LOGO! knows the following connectors: Connectors Inputs LOGO! Basic / Pure DM LOGO! 230RC/RCo, LOGO! 24 RC/RCo Two groups: I1... I4 and I5 ... I8 I9 ... I24 LOGO! 12/24RC/ RCo, LOGO! 24/24o I1... I6, I7, I8 AI1, AI2 I9 ... I24 Outputs Q1...Q4 lo Logical '0' signals (off) hi Logical '1' signals (on) x An existing connection that is not used AM AI1...AI8 AI3...AI8 Q5 ... Q16 none DM: Digital module. AM: Analog module. LOGO! Manual A5E00228550-01 41 Programming LOGO! 3.2 Blocks and block numbers This chapter shows you how to use LOGO! elements to create complex circuits and how blocks and I/O are interconnected. In Chapter 3.3 we are going to show you how to transform a conventional circuit to obtain a LOGO! circuit program. Blocks A block in LOGO! represents a function that is used to convert input information into output information. Previously you had to wire the individual elements in a control cabinet or terminal box. When you create the circuit program, you interconnect the blocks. To do so, simply select the connection you require from the Co menu The menu name Co is an abbreviation of the term "Connector". Logic operations The most elementary blocks are the logic operations: AND OR ... I1 I2 x x 1 Q Inputs I1 and I2 are here connected to the OR block. The last two inputs of the block remain unused and are identified be the creator of the circuit program with an 'x'. These special functions offer you a significantly higher performance: Pulse relay Up/down counter On-delay Softkey .... In Chapter 4 you will find a full list of the LOGO! functions. 42 LOGO! Manual A5E00228550-01 Programming LOGO! View of blocks on the LOGO! display The figure below shows a typical view of the LOGO! display. As you can see, it can show only one block at a time. We have therefore introduced block numbers to help you check the circuit structure. View of the LOGO! display Block number assigned by LOGO! A further block is connectedat this point Input 1 x B2 I3 x B1 Q1 This connector is not required Output Block Assigning a block number LOGO! assigns each new block a circuit program a block number. LOGO! uses these block numbers to indicate the block interconnections. Hence, these numbers primarily represent a help for your orientation in the circuit program. Block numbers B2 x I1 I2 I3 These blocks are interconnected 1 B1 B3 x I4 I5 I6 1 B1 B1 x B2 B3 x 1 Q1 B1 Q1 Scrolling the circuit program using the key LOGO! Manual A5E00228550-01 43 Programming LOGO! The figure above shows you three views of the LOGO! display, which represent the circuit program. As you can see, LOGO! interconnects the blocks using their numbers. Advantages of the block numbers You can connect almost any block to an input of the current block by means of its block number. In this way, you can reuse the interim results of logical or other operations, reduce programming effort, save memory space and clean up your circuit layout. To do so, however, you need to know how LOGO! has named the blocks. Note We advise you to create an organizational program chart. You will find this a valuable help when you create the circuit program, because you can enter all block numbers assigned by LOGO! in this chart. By using the LOGO!Soft Comfort software to program the LOGO!, you can directly create a function chart of your circuit program. LOGO!Soft Comfort also allows you to assign 8-character names to up to 64 blocks, and to view these on the LOGO! display in parameter assignment and programming mode (see Chapter 3.4). 44 LOGO! Manual A5E00228550-01 Programming LOGO! 3.3 The way to LOGO!, starting with the circuit diagram View of a circuit diagram You know, of course, how a circuit logic is represented in a circuit diagram. Nevertheless, here is an example: S1 S2 K1 S3 K1 E1 The load E1 is switched on and off by means of the switches (S1 OR S2) AND S3. Relay K1 picks up when the condition (S1 OR S2) AND S3 is met. Creating this circuit with LOGO! In LOGO! you create a circuit logic by interconnecting blocks and connectors: L 1 S1 ... S3 Wiring of the inputs Circuit program in LOGO! I1 I2 x N LOGO! Manual A5E00228550-01 1 I3 & Q1 x Wiring of the outputs 45 Programming LOGO! Note Although you have four inputs available for logic operations (Basic functions, see Chapter 4.2), most of the views will only show three inputs for reasons of clarity. You program this fourth input and assign parameters just like you do with the other three inputs. To create a circuit logic in LOGO!, start at the output. The output is the load or relay that is to be switched. Convert the circuit logic into blocks by working through the circuit, starting at the output and ending at the input: Step 1: The make contact S3 is interconnected in series to output Q1 and to a further circuit element. A series connection corresponds with the AND block: & I3 Q1 x Step 2: S1 and S2 are connected in parallel. A parallel circuit corresponds with the OR block: I1 I2 x 1 I3 & Q1 x Unused inputs The circuit program automatically assigns the unused connectors a status that ensures proper functioning of the relevant block. If you like, you can label unused connectors with an 'x' identifier. In our example we shall use only two inputs of the OR block and two inputs of the AND block; the relevant unused third and fourth inputs are identified at the connector with an 'x'. Now connect the I/Os to the LOGO! . 46 LOGO! Manual A5E00228550-01 Programming LOGO! Wiring Connect the switches S1 to S3 to the screw terminals of your LOGO! : S1 to connector I1 of LOGO! S2 to connector I2 of LOGO! S3 to connector I3 of LOGO! The output of the AND block controls the relay at output Q1. The load E1 is connected to output Q1. Wiring example The following figure shows you the wiring, based on a 230 V AC version of LOGO!. L1 N S S S 1 2 3 L1 1 N Q1 I1 I2 I3 Input wiring I4 2 Output wiring L1 N LOGO! Manual A5E00228550-01 47 Programming LOGO! 3.4 The 4 Golden rules for the operation of LOGO! Rule 1 Changing the operating mode You create the circuit program in programming mode. After power is on, and when the display shows "No Program / Press ESC", press the ESC key to select programming mode. Timer and parameter values of an existing circuit program can be edited both in parameter assignment mode and in programming mode. During parameter assignment the LOGO! is in RUN mode, i.e. it continues execution of the circuit program (see Chapter 5). To work in programming mode, you need to terminate the circuit program by calling the "Stop" command. Select the 'Start' command on the main menu to set RUN mode. When the system is in RUN, you can return to parameter assignment mode by pressing the ESC key. When parameter assignment mode is open and you want to return to programming mode, select the "Stop" command from the parameter assignment menu, and confirm "Stop Prg" prompt with "Yes". To do so, move the cursor to "Yes" and confirm with OK. For more details on operating modes, refer to Appendix D. Note The following applies to 0BA2 device versions and earlier: You can open programming mode by pressing ++OK. You set parameter assignment mode by pressing ESC+OK. 48 LOGO! Manual A5E00228550-01 Programming LOGO! Rule 2 Outputs and inputs Always create your circuit program by working from the output to the input. You can connect an output to several inputs, but not the same input to several outputs. Within the same program path you may not connect an output to an upstream input. For such internal recursions you should interconnect flags or outputs. Rule 3 Cursor and cursor movement The following applies when you edit a circuit program: You can move the cursor when it appears in the form of an underscore: - Press , , or to move the cursor in the circuit program. - Press OK to change to "Select connector/block" - Press ESCto exit programming mode. You select a connector/block when the cursor appears as solid square - Press or to select a connector or a block. - Confirm with OK. - Press ESC to return to the previous step. Rule 4 Planning Before you start to create a circuit program, you should either first create design on paper or program LOGO! directly using LOGO!Soft Comfort. LOGO! can only save complete and faultless circuit programs. LOGO! Manual A5E00228550-01 49 Programming LOGO! 3.5 Overview of the LOGO! menus Programming mode Main menu >Program.. Card.. Clock.. Start Programming menu OK >Edit.. Clear Prg Password ESC OK Transfer menu ESC = LOGO! > Card Card CopyProtect OK ESC Real-time clock menu >Set Clock S/W Time Sync Parameter assignment mode Parameter assignment menu >Stop Set Param Set Clock Prg Name For more details on these menus, refer to Appendix D. 50 LOGO! Manual A5E00228550-01 Programming LOGO! 3.6 Writing and starting the circuit program After you have designed a circuit, you want to write it to your LOGO! . The small example below shows how to do this. 3.6.1 Select programming mode You have connected the LOGO! to the power supply and switched it on. The display now shows you the message: No Program Press ESC Switch the LOGO! to programming mode by pressing the ESC. This will take you to the main menu of the LOGO!: >Program.. Card.. Clock.. Start LOGO!'s main menu The first character in the first line is the ">" cursor. Press and to move the ">" cursor up and down. Move it to "Program.." and confirm with OK. LOGO! opens the programming menu. >Edit.. Clear Prg Password LOGO! Manual A5E00228550-01 The LOGO!'s programming menu 51 Programming LOGO! Here you can also move the ">" cursor by pressing and . Move the ">" cursor to "Edit.." (for editing, i.e. input) and confirm with OK. >Edit Prg Edit Name Memory? The Edit menu of LOGO! Move the ">" cursor to "Edit Prg" (for editing the circuit program) and confirm with OK. LOGO! now shows you the first output: The first output of LOGO! Q1 You are now in programming mode. Press and to select the other outputs. Now start to edit your circuit program. Note Because we have not yet saved a password for the circuit program in LOGO!, you can directly enter editing mode. When you select "Edit Prg" after you have saved a password-protected circuit program, you are prompted to enter a password and to confirm it with OK. You can only edit the program after you have entered the correct password (see Chapter 3.6.5.). 52 LOGO! Manual A5E00228550-01 Programming LOGO! 3.6.2 The first circuit program Let us now take a look at the following parallel circuit consisting of two switches. Circuit diagram The corresponding circuit diagram: S1 S2 The load is switched on with S1 OR S2. LOGO! interprets this parallel circuit as an 'OR' logic, because S1 OR S2 switches on the output. K1 K1 E1 Translated into a LOGO! circuit program this means: Relay K1 is at output Q1 is controlled by means of an OR block. Circuit program S1 is connected to the I1 and and S2 to the I2 input connector of the OR block. The corresponding layout of the circuit program in LOGO!: I1 I2 x LOGO! Manual A5E00228550-01 1 Q1 53 Programming LOGO! Wiring The corresponding wiring: L1 S1 N S2 L1 1 Q1 N 2 I1 I2 I1 1 I3 Q2 2 I4 I5 1 Q3 2 I6 I7 1 I8 Q4 2 L N S1 switches input I1, while S2 switches input I2. The load is connected to the relay Q1. 3.6.3 Circuit program input Let us now write the circuit program, starting at the output and working towards the input. LOGO! initially shows the output: The first LOGO! output Q1 54 LOGO! Manual A5E00228550-01 Programming LOGO! You will see an underscore below the Q in Q1, which is the cursor. The cursor indicates your current position in the circuit program. You can move the cursor by pressing the , , and keys. Now press the key. The cursor moves to the left. The cursor indicates your current position in the circuit program. - Q1 At this point you enter only the first (OR) block. Press OK to select editing mode. The cursor is displayed as a solid square: You can now select a connector or a block Co Q1 The cursor no longer appears in the form of an underscore; but instead as a flashing solid square. LOGO! offers you here various options. Select GF (basic functions) by pressing the key until GF appears, and confirm with OK. LOGO! now shows the first block from the list of basic functions: B1 & The AND is the first block of the basic functions list. The solid square cursor prompts you to select a block. Q1 LOGO! Manual A5E00228550-01 55 Programming LOGO! Now press play: or until the OR block appears on the dis- B1 1 The solid square cursor is still positioned on the block. Q1 Press OK to confirm your entries and exit the dialog. The display now shows: B1 - 1 Q1 Block number Your complete circuit program layout B1 1 Q1 You have now entered the first block. Each new block is automatically assigned a block number. The only thing left to do is to interconnect the block inputs. This is how it is done: Press OK. The display now shows: B1 Co 1 Q1 Select the Co list: Press OK The display now shows: B1 x 1 Q1 56 LOGO! Manual A5E00228550-01 Programming LOGO! The first element of the Co list is the "Input not used" character, namely the 'x'. Press or to select input I1. Note Press to go the start of the Co list: I1, I2 .... to lo, then again 'x'. Press to go to the end of the Co list: lo, hi, Q ..... to I1, and once again 'x'. B1 I1 1 Q1 Press OK. I1 is now connected to the input of the OR block. The cursor jumps to the next input of the OR block. The display now shows: B1 I1 - Your complete circuit program in LOGO! up to now: B1 1 Q1 I1 1 Q1 Now you connect input I2 to the input of the OR block. You already know how to do this: 1. Switch to editing mode: Press OK 2. To select the Co list: Press or 3. To confirm the Co list with: Press OK 4. To select I2: Press or 5. To apply I2: Press OK LOGO! Manual A5E00228550-01 57 Programming LOGO! I2 is now connected to the input of the OR block: The display now shows: Your circuit program layout in LOGO! up to now B1 I1 I2 1 Q1 B1 1 I1 Q1 I2 We do not need the last two inputs of the OR block for this circuit program. You can mark the unused inputs with an 'x'. Enter the 'x' character twice: 1. Switch to editing mode: Press OK 2. To select the Co list: Press or 3. To accept the Co list: Press OK 4. To select 'x': Press or 5. To apply x: Press OK LOGO! returns to output Q1. The display now shows: B1 58 Q1 This is the layout of your circuit program B1 I1 I2 x 1 Q1 LOGO! Manual A5E00228550-01 Programming LOGO! Note You can invert individual inputs of the basic and special functions, i.e. if an input carries a logical "1" signal, the circuit program will output a logical "0"; vice versa, a logical "0" is inverted into a logical "1" signal. To invert an input, move the cursor to the relevant position, e.g.: B1 I1 I2 I3 x 1 Q1 Confirm with OK. Now press or to invert this input: Next, press ESC. B1 I1 I2 I3 x 1 Q1 Your circuit program layout B1 I1 I2 I3 x 1 Q1 You can review your first circuit program by pressing or to move the cursor through the circuit program. We shall now exit circuit programming mode. This is how it is done: Return to the programming menu: Press ESC LOGO! Manual A5E00228550-01 59 Programming LOGO! Note LOGO! has now saved your circuit program to nonvolatile memory. The circuit program remains in the LOGO! memory until you explicitly delete it. 3.6.4 Assigning a circuit program name You can assign your circuit program a name that consists of up to 16 uppercase/lowercase letters, numbers and special characters. In the programming menu: 1. To move the ">" cursor to 'Edit..': Press or 2. To accept 'Edit': Press OK 3. Move the ">" cursor to 'Edit Name': Press or 4. To accept 'Edit Name': Press OK Press and to list the alphabet from A (a) to Z (z), numbers and special characters, either in ascending or descending order. You can select any letter, number or character. To enter a space character, simply movie the cursor with to the next position. This character is the first one in the list. Examples: Press once to select an " A " four times to select " { ", etc. The following character set is available: A B C D E F G P Q R S T U V f g h i j k v w x y z " # $ % & < = > ? 60 H I J K L M N O W X Y Z a b c d e l m n o p q r s t u 0 1 2 3 4 5 6 7 8 9 ! ' ( ) * + , - . / : ; @ [ \ ] ^ _ ` { | } ~ LOGO! Manual A5E00228550-01 Programming LOGO! Let us assume you want to name your circuit program "ABC": 5. Select " A": Press 6. Move to the next letter: Press 7. Select " B": Press 8. Move to the next letter: Press 9. Select " C": Press 10.To confirm the complete name: Press OK Your circuit program is now named "ABC", and you are returned to the programming menu. To change the name of your circuit program, proceed in the same way. Note You can change the name of the circuit program only in programming mode. You can read the name both in programming and in parameter assignment mode 3.6.5 Password You can protect a circuit program from unauthorized access by assigning it a password. To assign a password A password may have a maximum length of 10 characters, and consists only of uppercase letters (A to Z). Directly at the LOGO!, the password can be assigned, edited or deactivated only in the "Password" menu. In the programming menu: 1. Move the ">" cursor to 'Password': Press or 2. To confirm the 'Password': Press OK Press or to move up and down the alphabet to select your letters. Because LOGO! only provides uppercase letters for the password, you can quickly access to letters "at the end" of the alphabet by using the button: LOGO! Manual A5E00228550-01 61 Programming LOGO! Press once to select "Z" Press twice to select "Y", etc. Let us assign the password "AA" to our first circuit program. The display now shows: Old: No Password New: This procedure is the same as for entering the name of the circuit program. Select "New" and enter: 3. Select " A": Press 4. To move to the next letter: Press 5. Select " A": Press The display now shows: Old: No Password New: 6. To confirm the password: Press OK Your circuit program is now protected with the password "AA", and you are returned to the programming menu. 62 LOGO! Manual A5E00228550-01 Programming LOGO! Note You can cancel the input of a new password with ESC. In this case, LOGO! returns to the programming menu without saving the password. You can also set your password using LOGO!Soft Comfort. You can not edit a password-protected circuit program at the LOGO! or upload it to LOGO!Soft Comfort unless you enter the correct password. To allow you to create and edit a circuit program for a protected module (Card), you first need to assign a password to this new program (see Chapter 6.1). Changing the Password You need to know the current password in order to change it. In the programming menu: 1. Move the '>' cursor to 'Password': Press or 2. To confirm the 'Password': Press OK Select "Old" and enter your old password (in our case: 'AA') by repeating steps 3 through 6 as described earlier. The display now shows: Old: AA New: Now you can select "New" to enter the new password, e.g. "ZZ": 3. Select "Z": Press 4. To move to the next letter: Press 5. Select "Z": Press LOGO! Manual A5E00228550-01 63 Programming LOGO! The display now shows: Old: AA New: ZZ 6. To confirm your new password: Press OK Your new password "ZZ" is now set, and you are returned to the programming menu. Deactivating the Password Let us assume you want to deactivate the password for whichever reason. For example, you want to allow another user to edit your circuit program. You must know your current password (in our example "ZZ"), same as if you were changing it. In the programming menu: 1. Move the '>' cursor to 'Password': Press or 2. To confirm the 'Password': Press OK Select "Old" and enter your current password under as described in steps 3 to 5. Confirm your entries with OK. The display shows: Old: ZZ New: Clear the password by leaving the input box blank: 3. To confirm the "blank" password: Press OK The password is "cleared", and you are returned to the programming menu. 64 LOGO! Manual A5E00228550-01 Programming LOGO! Note This action disables the password prompt, and thus permits access without password. Let the password prompt be deactivated for the time being, in order to accelerate progress in our further exercises and examples. Password: Wrong Password! When the user inputs the wrong password and confirms the input with OK, LOGO! does not open editing mode, but returns to the programming menu. This repeats itself over and again until you input the correct password. LOGO! Manual A5E00228550-01 65 Programming LOGO! 3.6.6 Switching LOGO! to RUN mode In the main menu, select RUN to start LOGO!. 1. To return to the main menu: Press ESC 2. Move the '>' cursor to 'Start': Press or 3. To confirm 'Start': Press OK LOGO! runs the circuit program and and shows the following display: Display field of the LOGO! in RUN mode Mo 09:00 2003-01-27 Press I: 0.. 123456789 1..0123456789 2..01234 Date and current time-of-day (only for versions with realtime clock). This element flashes if the date and time are not set. Inputs I1 to I9 Inputs I10 to I19 Inputs I20 to I24 Press Q: Outputs Q1 to Q9 0.. 123456789 1..0123456 Outputs Q10 to Q16 Press M: 0.. 123456789 1..0123456789 2..01234 Flags M1 to M9 Flags M10 to M19 Flags M20 to M24 Press ESC+Key 4 cursor keys for manual intervention in the circuit program (ESC+key) 66 LOGO! Manual A5E00228550-01 Programming LOGO! What is meant by: "LOGO! is in RUN"? In RUN mode, LOGO! executes the circuit program. To do so, LOGO! first reads the status at the inputs, determines the status of the outputs by means of the user program, and switches these on or off according to your settings. This is how LOGO! indicates the I/O status: Input/output status is '1': inverted Input/output status is '0': not inverted I: 0.. 123456789 1..0123456789 2..01234 Q: 0.. 123456789 1..0123456 In this example, only the inputs I1, I15, Q8 and Q12 are set "high". Status indication on the display L1 S1 Let us examine this, using our example: =1 I1 S2 I2 I: 0.. 123456789 1..0123456789 2..01234 Q: 0.. 123456789 1..0123456 When switch S1 is closed, the status at input I1 is hi. LOGO! computes the output states by means of the circuit program. Output Q1 = '1', in this case. When Q1 = '1', LOGO! sets relay Q1, and the load connected to Q1 is supplied with voltage. Q1 N LOGO! Manual A5E00228550-01 67 Programming LOGO! 3.6.7 Second circuit program Up to this point, you have successfully created your first circuit, and assigned it a name and, if desired, a password. In this section we are going to show you how to modify existing circuit programs and how to use the special functions. Using this second circuit program, we are going to show you how to: Add a block to an existing circuit program. Select a block for a special function. Assign parameters. Modifying circuits We shall use the first circuit program as a basis for the second, with some slight modifications. Let us take a first look at the circuit diagram for the second circuit program: L1 S1 You already know the first part of the circuit. S1 and S2 switch a relay, which is to be used to switch on the load E1, and to switch off the load with a delay of 12 minutes. K1 S2 E1 K1 N In LOGO!, this is the circuit program layout: I1 I2 x 1 This is the new block x Par Q1 You can see the OR block and the output relay Q1 we have already used in the first circuit program. The only difference is the new off-delay block. 68 LOGO! Manual A5E00228550-01 Programming LOGO! Editing the circuit program Switch the LOGO! to programming mode. As a reminder: 1. Switch the LOGO! to programming mode (in RUN: Press ESC to enter the parameter assignment mode. Select the 'Stop' command, confirm with OK, then move the '>' cursor to 'Yes', and once again confirm with OK). See Page 48. 2. On the main menu, select "Program" 3. On the Programming menu, select "Edit", confirm with OK. Next, select "Edit Prg" and confirm with OK. If required, enter your password at the prompt and confirm with OK. You can now modify the current circuit program. Adding a block to a circuit program Move the cursor to the B in B1 (B1 is the number of the OR block): To move the cursor: Press B1 Q1 We now insert the new block at this position. Confirm with OK. LOGO! shows you the BN list BN LOGO! Manual A5E00228550-01 Q1 69 Programming LOGO! Press to select the SF list: The SF list contains the special function blocks. SF Q1 Press OK. The block of the first special function is shown: Trg Par Q1 When you select a special or basic function block, LOGO! shows you the relevant function block. The solid square cursor is positioned on the block. Press or to select the required block. Select your block (off-delay, see the next figure), and then press OK: Before you press 'OK', this shows the entry Trg B1 R Par B2 The added block is assigned the block number B2. The cursor is positioned at the top input of the added block. Q1 The B1 block previously connected to Q1 is automatically connected to the uppermost input of the new block. Note that you can only interconnect digital inputs with digital outputs or analog inputs with analog outputs. The 'old' block will otherwise be lost. The off-delay block has three inputs. At the top is the trigger input (Trg) you use to start the off-delay time. In our example, the OR block B1 triggers the off-delay. You reset the time and the output with a signal at the reset input. Set the off-delay time at parameter T of the input Par. 70 LOGO! Manual A5E00228550-01 Programming LOGO! In our example we do not use the reset input of the offdelay function, and we identify it with an 'x' connector. B2 B1 x Par This is what the display should now show Q1 Assigning block parameters Now you set the off-delay time T: 1. Move the cursor to Par, if it not already at this position: Press or 2. Switch to editing mode: Press OK LOGO! shows the parameters in the parameter assignment window: T: The block parameter B2 is a time function B2 +R T =00:00s Time value "+" means: The parameter is shown and can be modified in the parameter assignment mode. "R" means: Retentivity is enabled for this block. Timebase To change the time value: Press and to position the cursor. Press and to modify the value at the relevant position. Confirm your entries with OK. LOGO! Manual A5E00228550-01 71 Programming LOGO! Setting the time Set the time T = 12:00 minutes: 1. Move the cursor to the first digit: 2. Select the digit '1': 3. Shift the cursor to the second digit: 4. Select digit '2': 5. Move the cursor to the unit: 6. Select the timebase 'm' (for minutes): Press Press Press Press Press Press or or or or or or Showing/hiding parameters - the parameter protection mode If you want to show/hide the parameter and allow/prevent its modification in parameter assignment mode: 1. Move the cursor to the protection mode: Press or 2. Select the protection mode: Press or The display should now show: B2 T=12:00m +R or Protection mode +: The value of the time T can be modified in parameter assignment mode 3. Confirm your entries with: B2 T=12:00m -R Protection mode - : The value of the time T is hidden in parameter assignment mode OK Enabling/disabling retentivity To decide whether you want to retain your current data after a power failure or not: 1. Move the cursor to the retentivity setting: Press or 2. Select the retentivity setting: Press or 72 LOGO! Manual A5E00228550-01 Programming LOGO! The display now shows: B2 T=12:00m -R B2 T=12:00m or -/ Retentivity R: Current data are retained Retentivity /: Current data are not retained 3. Confirm your entries with OK Note For further information on the protection mode, refer to Chapter 4.3.5. For further information on retentivity, refer to Chapter 4.3.4. You can modify the protection mode and retentivity setting only in programming mode, i.e. this is not possible in parameter assignment mode. In this manual, the protection mode ("+" or "-") and retentivity ("R" or "/") settings are only shown in the displays where these can actually be changed. Verification of the circuit program This program branch for Q1 is now completed. LOGO! shows you the output Q1. You can once again view the circuit program on the display. Use the keys to browse the circuit program, i.e. press or to move from block to block, and to move between the inputs at a block. LOGO! Manual A5E00228550-01 73 Programming LOGO! Closing the programming mode Although you were shown how to exit the programming mode when you created your first circuit program, here is a reminder: 1. To return to the programming menu: Press ESC 2. To return to the main menu: Press ESC 3. To move the '>' cursor to 'Start': Press or 4. To confirm 'Start': Press OK LOGO! is back in RUN mode: Mo 09:30 2003-01-27 You can press or to scroll the pages and to monitor the I/O states. 3.6.8 Deleting a block Let us assume you want to delete the block B2 from your circuit program and connect B1 directly to Q1. B1 B2 I1 I2 x x Par Q1 Proceed as follows: 1. Switch the LOGO! to programming mode (as a reminder, refer to Page 48). 2. Select 'Edit': Press or 3. Confirm 'Edit': Press OK 4. Select 'Edit Prg': Press or 5. Confirm 'Edit Prg': Press OK (If required, enter your password and confirm with OK). 74 LOGO! Manual A5E00228550-01 Programming LOGO! 6. To move the cursor to the input of Q1, i.e. to B2, press : B2 Q1 7. Confirm with OK. 8. Now replace block B2 with block B1 at output Q1. The procedure: - Select the BN list: Press or - Accept the BN list: Press OK - Select 'B1': Press or - Apply 'B1': Press OK Result: Block B2 is deleted, because it is no longer used in the circuit. Block B1 has replaced B2 directly at the output. 3.6.9 Deleting block groups Let us assume you want to delete the blocks B1 and B2 from the following circuit program (corresponds with the circuit program in Chapter 3.6.7). B1 B2 I1 I2 x x Par Q1 Proceed as follows: 1. Switch the LOGO! to programming mode (as a reminder, refer to page 48). 2. To select 'Edit': Press or 3. To confirm 'Edit': Press OK 4. To select 'Edit Prg': Press or LOGO! Manual A5E00228550-01 75 Programming LOGO! 5. To confirm 'Edit Prg': Press OK (if required, enter your password and confirm with OK). 6. To move the cursor to the input of Q1, i.e. to B2, press : B2 Q1 7. Confirm with OK. 8. Now set the connector 'x' at output Q1 instead of block B2. To do so: - Select the Co list: Press or - Accept the Co list: Press OK - Select 'x': Press or - Apply 'x': Press OK Result: Block B2 is deleted, because it is no longer used in the circuit. This includes all blocks connected to B2. In this example, block B1 also. 3.6.10 Correcting typing errors Programming errors can be corrected easily in LOGO! : Provided editing mode is not yet closed, you can revert by one step by pressing ESC. If you have already configured all inputs, simply reconfigure the faulty input: 1. Move the cursor to the faulty position 2. Change to editing mode. Press OK 3. Enter the correct input circuit. You can only replace a block with a block that has exactly the same number of inputs. However, you can delete the old block and then insert a new one. You can choose any new block. 76 LOGO! Manual A5E00228550-01 Programming LOGO! 3.6.11 Deleting the circuit program To delete a circuit program: 1. Switch the LOGO! to programming mode >Program.. Card.. Clock.. Start LOGO! opens the main menu 2. On the main menu, press to 'Program'. Press OK. >Edit.. Clear Prg Password or to move the '>' cursor LOGO! changes to the programming menu 3. Move the '>' cursor to 'Clear Prg': 4. Confirm 'Clear Prg': Press or Press OK Clear Prg >No Yes To cancel deletion of the circuit program, leave the '>' cursor at 'No' and press OK. LOGO! Manual A5E00228550-01 77 Programming LOGO! If you are sure that you want to delete the circuit program from memory: 5. Move the '>' cursor to 'Yes': Press or 6. Press OK. Password? ZZ To prevent unintentional deletion of your circuit program, you are prompted to enter your password (provided you have assigned one). 7. Enter your password. 8. Press OK. The circuit program is deleted. Note Although you may have forgotten your password, you can still delete the circuit program by entering the wrong password four times. 3.6.12 Summertime/wintertime conversion You can enable or disable automatic Summertime/wintertime conversion in programming mode by calling the "Clock" menu command. 1. Switch the LOGO! to programming mode. 2. You are now in the main menu and want to select the 'Clock' menu command: Press or 3. Confirm 'Clock': Press OK 4. Move the '>' cursor to 'S/W Time': Press or 5. Confirm 'S/W Time': Press OK 78 LOGO! Manual A5E00228550-01 Programming LOGO! LOGO! shows the following display: >On Off S/W Time: Off The current setting of automatic S/W Time conversion is shown in the bottom row. The default setting is 'Off': disabled. Enabling summertime/wintertime conversion You now want to enable this conversion and define or set its parameters: 1. Move the '>' cursor to 'On': Press or 2. Confirm 'On': Press OK The display shows: >EU 3. Select the desired conversion: Press or What is shown on the display ?: 'EU' represents the start and end of European summertime. 'UK' represents the start and end of summertime in the United Kingdom. 'US' represents the start and end of summertime in the United States. 'AUS' represents the start and end of Australian summertime. 'AUS-TAS' represents the start and end of Australian/ Tasmanian summertime. 'NZ' represents the start and end of New Zealand summertime. LOGO! Manual A5E00228550-01 79 Programming LOGO! . . : Here you can enter any month, day and time zone difference. The preset conversion data for EU, UK and US are found in the table below: Start of summertime End of summertime Time zone difference EU Last Sunday in March: 02:00-->03:00 Last Sunday in October: 03:00-->02:00 60 Min. UK Last Sunday in March: 01:00-->02:00 Last Sunday in October: 02:00-->01:00 60 Min. US First Sunday in April: 02:00-->03:00 Last Sunday in October: 02:00-->01:00 60 Min. AUS Last Sunday in October: 02:00-->03:00 Last Sunday in March: 03:00-->02:00 60 Min. AUS- First Sunday in OctoTAS ber: 02:00-->03:00 Last Sunday in March: 03:00-->02:00 60 Min. NZ First Sunday in October: 02:00-->03:00 Third Sunday in March: 03:00-->02:00 60 Min. .. Customizing the month and the day: 02:00--> 02:00 + Time zone difference Customizing the month and the day: 03:00--> 03:00 - Time zone difference User-defined (resolution in minutes) Note You can specify a time zone difference between 0 and 180 minutes. Let us assume you want to enable European summertime/ wintertime conversion: 4. Move the '>' cursor to 'EU': Press or 5. Confirm 'EU': Press OK 80 LOGO! Manual A5E00228550-01 Programming LOGO! LOGO! shows the following display: >On Off S/W Time: OnEU LOGO! indicates that European S/W Time conversion is enabled. User-defined parameters If none of the parameters/conversions apply to your country, you can customize these under menu item '. .'. To do so: 1. Confirm 'On' once again: Press OK 2. Move the '>' cursor to '. .': Press or 3. Confirm the menu item '. .' : PressOK The display shows: Cursor / solid square MM-DD + : 0 01-01 - : 01-01 =000min Month (MM) and Day (DD) Start of summertime End of summertime The desired time zone difference in [min] Let us assume you want to configure the following parameters: Start of summertime = 31st of March, end of summertime = 1st of November, time difference of 120 minutes. This is how you can enter your data: Press or to move the solid square/cursor. Press and to change the value at the cursor position. LOGO! Manual A5E00228550-01 81 Programming LOGO! The display shows: MM-DD + : 0 03-31 - : 11-01 =120 min 31. March 1. November Time difference of 120 min Confirm all your entries with OK. You have now customized the summertime/wintertime conversion. The LOGO! display now shows: >On Off S/W Time: On.. LOGO! indicates that summertime/wintertime conversion is enabled, and that user-defined parameters ( '..' ) have been set. Note To disable summertime/wintertime conversion in this menu, you merely confirm 'Off' with OK. 82 LOGO! Manual A5E00228550-01 Programming LOGO! 3.6.13 Synchronization Time synchronization between LOGO! and the connected expansion modules can be enabled/disabled in programming mode by means of the real-time clock menu ("Clock" menu item). 1. Switch the LOGO! to programming mode. 2. You are now in the main menu, and want to select 'Clock': Press or 3. Confirm 'Clock': Press OK 4. Move the '>' cursor to 'Sync': Press or 5. Apply 'Sync': Press OK LOGO! shows the following display: >On Off Sync: Off The current setting of the automatic synchronization function is displayed in the bottom row. The default setting is 'Off': disabled. Enabling synchronization You want to enable synchronization: 1. Move the '>' cursor to 'On': Press or 2. Confirm 'On': Press OK LOGO! shows the following display: >On Off Sync: On When synchronization is enabled, LOGO! transmits the time-of-day to the expansion modules once daily, after each transition to RUN mode and when the TOD is changed after a 'Set Clock' is executed or after a summertime/wintertime conversion. LOGO! Manual A5E00228550-01 83 Programming LOGO! 3.7 Memory space and circuit dimensions The size of a circuit program in LOGO! is limited by the memory space (memory used by the blocks). Memory areas Program memory: LOGO! allows only a limited number of blocks in your circuit program. The second limitation is based on the maximum number of bytes a circuit program may contain. The total number of bytes used can be determined by adding up the number of bytes used for the relevant function blocks. Retentive memory (Rem): In this area, LOGO! stores process variables which need to be retentive, e.g. the hours counter value. Blocks with optional retentivity use this memory area only if this function is actually enabled. Resources available in LOGO! A circuit program in LOGO! can occupy the following maximum resources: Bytes Blocks REM 2000 130 60 LOGO! monitors memory utilization, and offers only those functions from the lists for which it can actually provide sufficient memory space. 84 LOGO! Manual A5E00228550-01 Programming LOGO! Memory requirements The table below shows an overview of the memory requirements for the basic and special function blocks: Function Program memory Rem memory* AND 12 - AND with edge evaluation 12 - NAND (NOT AND) 12 - NAND with edge evaluation 12 - OR 12 - NOR (NOT OR) 12 - XOR (exclusive OR) 8 - NOT (Negation) 4 - On-delay 8 3 Off-delay 12 3 On-/Off-delay 12 3 Retentiveon-delay 12 3 Wiping relay (pulse output) 8 3 Edge triggered wiping relay 16 4 Asynchronous pulse generator 12 3 Random generator 12 - Stairway lighting switch 12 3 Multiple function switch 16 3 Weekly timer 20 - Yearly timer 8 - Basic functions Special functions Times LOGO! Manual A5E00228550-01 85 Programming LOGO! Function Program memory Rem memory* Up/down counter 24 5 Hours counter 24 9 Threshold trigger 16 - Analog threshold trigger 16 - Analog differential trigger 16 - Analog comparator 24 - Analog value monitoring 20 - Analog amplifier 12 - Latching relay 8 1 Pulse relay 12 1 Message texts 8 - Softkey 8 2 Shift register 12 1 Counter Analog Others *: Bytes in the Rem memory area, if retentivity is enabled. Utilization of memory areas An indication of insufficient memory space is given, when the system does not allow you to add a further block to your circuit program. LOGO! offers you only the blocks for which it can provide sufficient memory space. If LOGO! memory space is insufficient to hold any further blocks you select from a block list, the system will deny access to this list. If memory space is fully occupied, optimize your circuit program, or install a second LOGO!. 86 LOGO! Manual A5E00228550-01 Programming LOGO! Calculating memory requirements When calculating the memory requirements of a circuit, you must always take all individual areas of memory into account. Example: Bytes REM 20 Bytes REM - 12 B3 - B2 B1 No 1 No 2 No 3 x Q1 x I2 B4 I1 Par B6 B5 I3 I4 x Par Q2 The sample circuit program contains: Block no no. Memory area Function Bytes Blocks REM B1 OR 12 1 - B2 AND 12 1 - B3 Weekly timer 20 1 - B4 On-delay* 8 1 3 B5 Stairway lighting switch 12 1 0 B6 AND 12 1 - Resources used by the circuit program 76 6 3 Memory space limits in LOGO! 2000 130 60 Still available in LOGO! 1924 124 57 *: Configured with retentivity. Hence, this circuit program fits into LOGO!. LOGO! Manual A5E00228550-01 87 Programming LOGO! Indication of available memory space LOGO! shows you the amount of free memory space. Proceed as follows: 1. Switch the LOGO! to programming mode (as a reminder, refer to page 48). 2. Select 'Edit': Press or 3. Accept 'Edit': Press OK 4. Select 'Memory?': Press or 5. Accept 'Memory?': Press OK The display now shows: Free Memory: Byte =1924 Block= 124 Rem = 57 88 LOGO! Manual A5E00228550-01 4 LOGO! functions Organization LOGO! provides you with various elements in programming mode. In order to maintain the overview, we have organized the elements in 'Lists'. These lists are: Co: Connector list (Connector) (see Chapter 4.1) GF: List of the basic functions AND, OR, ... (refer to Chapter 4.2) SF: List of the special functions (refer to Chapter 4.4) BN: List of reusable blocks configured in the circuit program List contents All lists show the elements available in LOGO!. Usually, this includes all connectors, basic functions and special functions the LOGO! knows. This includes all the blocks you have created in LOGO! by the time you call the BN list. If not all is shown LOGO! does not show all elements if: No further blocks may be added. This is either an indication of insufficient memory space or that the maximum number of blocks has been reached. A specific block's memory space requirement would exceed the space available in LOGO!. See Chapter 3.7. LOGO! Manual A5E00228550-01 89 LOGO! functions 4.1 Constants and connectors - Co Constants and connectors (= Co) represent inputs, outputs, flags and constant voltage levels (constants). Inputs: 1) Digital inputs Digital inputs are identified with an I. The number of the digital inputs (I1, I2, ...) corresponds with the number of the input connectors of the LOGO! Basic and of the connected digital modules, in the order of their installation. See the following figure. 2) Analog inputs The LOGO! versions LOGO! 24, LOGO! 24o, LOGO! 12/24RC and LOGO! 12/24RCo are equipped with the inputs I7 and I8, which can also be programmed for use as AI1 and AI2 inputs. Signals at the I7 and I8 inputs are interpreted as digital values, and those at the AI1 and AI2 inputs are interpreted as analog values. The inputs of a connected analog module are numbered according to the already existing analog inputs. Special functions whose inputs should only be connected to analog inputs are offered in programming mode when you select the input signal, i.e. the analog inputs AI1...AI8, analog flags AM1...AM6, the block numbers of a function with analog output or the analog outputs AQ1 and AQ2. Outputs: 1) Digital outputs Digital outputs are identified by the character Q. The output numbers (Q1, Q2, ... Q16) correspond with the numbers of the output connectors at the LOGO! Basic and with those of the expansion modules, in their order of installation. See the following figure. 90 LOGO! Manual A5E00228550-01 LOGO! functions There are also 16 blank outputs available. These are identified with an x and can not be reused in a circuit program (in contrast to flags, for example). The list shows all programmed blank outputs, and one blank output which is not yet configured. A blank output, for example, is useful for the special function "Message texts" (see Chapter 4.4.23), if only the message text is of significance to a circuit program. 2) Analog outputs Analog outputs are identified by the letters AQ. Two analog outputs are available, namely AQ1 and AQ2. You can only set an analog value at the analog output, i.e. a function with an analog output or analog flag AM. Inputs L+ M I1 I2 I3 I4 I5 I6 AI1 AI2 L+ M I9 I10 I11I12 L+ M RUN/STOP L+ M RUN/STOP L+ M I13I14I15 I16 RUN/STOP PE Q6 Q10 1 2 1 1 2 1INPUT 2x (..10 V/..20 mA) Q9 2 2 1 2 Q8 A!3 M3U3AI4M4 U4 Q11 1 2 Q12 Q7 1 2 1 2 Q5 1 Q1 2 1 Q2 2 1 2 Q3 1 2 Q4 Outputs Analog inputs Flag blocks Flag blocks are identified by the letters M or AM . These are virtual outputs, which output the value of their inputs. LOGO! provides 24 digital flags M1 ... M24 and 6 analog flags AM1 ... AM6. LOGO! Manual A5E00228550-01 91 LOGO! functions Startup flag Flag M8 is set in the first cycle of the user program and can thus be used in your circuit program as startup flag. This signal is automatically reset after the circuit program has completed its first cycle. The M8 flag can be used in all further cycles for setting, deletion and evaluation procedures in the same way as other flags. Note The output of the flag always carries the signal of the previous program cycle. This value does not change within the same program cycle. Shift register bits LOGO! provides the shift register bits S1 to S8, which are assigned the read-only attribute in the circuit program. The content of shift register bits can only be modified by means of the "Shift register" special function (see Chapter 4.4.25). Cursor keys Up to four cursor keys are available to you, namely C , C , C and C ("C" = "Cursor"). Cursor keys are programmed for the circuit program in the same ways as other inputs. You can set the cursor keys in the corresponding display while the system is in RUN (see Chapter 3.6.6), and in an active message text (ESC + Key). Cursor keys can save switches and inputs, and allow operator control of the circuit program. Levels Voltage levels are designated hi and lo. A constant "1" = hi or "0" = lo status at the block can be set by means of a permanent voltage level or constant value hi or lo. Open connectors Unused block connectors can be identified with an x. 92 LOGO! Manual A5E00228550-01 LOGO! functions 4.2 Basic functions list - GF Basic functions represent simple logical elements of Boolean algebra. You can invert the inputs of individual basic functions , i.e. the circuit program inverts a logical "1" at a relevant input to a logical "0"; if "0" is set at the input, the program sets a logical "1". A programming example is found in Chapter 3.6.3. The GF list contains the basic function blocks you can use for your circuit program. The following basic functions are available: View in the circuit diagram View in LOGO! Name of the basic function AND Series circuit make contact (see page 95) AND with edge evaluation (see page 96) NAND (NOT AND) (see page 97) Parallel circuit with break contacts NAND with edge evaluation (see page 98) LOGO! Manual A5E00228550-01 93 LOGO! functions View in the circuit diagram View in LOGO! Name of the basic function OR (see page 99) Parallel circuit with make contacts Series circuit with break contacts NOR (NOT OR) (see page 100) XOR (exclusive OR) Double changeover contact Break contact 94 (see page 101) NOT (negation, inverter) (see page 101) LOGO! Manual A5E00228550-01 LOGO! functions 4.2.1 AND Symbol in LOGO!: Circuit diagram of a series circuit with several make contacts: The output of the AND is only 1 if all inputs are 1, i.e. all contacts are closed. At an unused block input (x): x = 1. Table of the AND logic 1 2 3 4 Q 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 LOGO! Manual A5E00228550-01 95 LOGO! functions 4.2.2 AND with edge evaluation Symbol in LOGO!: The output of an edge triggered AND is only 1 if all inputs are 1 and if at least one input was low in the previous cycle. At an unused block input (x): x = 1. Timing diagram for the AND with edge evaluation 1 2 3 4 Q Cycle 96 1 2 3 4 5 6 7 8 9 10 LOGO! Manual A5E00228550-01 LOGO! functions 4.2.3 NAND (NOT AND) Parallel circuit with multiple break contacts in the circuit diagram: Symbol in LOGO!: The output of the NAND is only 0 if the status at all inputs is 1, i.e. the contacts are closed. At an unused block input (x): x = 1. Table of the NAND logic 1 2 3 4 Q 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 LOGO! Manual A5E00228550-01 97 LOGO! functions 4.2.4 NAND with edge evaluation Symbol in LOGO!: The output status of the NAND with edge evaluation is only 1 if at least one input is 0 and if all inputs were 1 in the previous cycle. At an unused block input (x): x = 1. Timing diagram for the NAND with edge evaluation 1 2 3 4 Q Cycle 98 1 2 3 4 5 6 7 8 9 10 LOGO! Manual A5E00228550-01 LOGO! functions 4.2.5 OR Circuit diagram of a parallel circuit with several make contacts: Symbol in LOGO!: The output status of the OR element is only 1 if at least one input is 1, i.e. at least one of the contacts is closed. At an unused block input (x): x = 0. Table of the OR logic 1 2 3 4 Q 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 LOGO! Manual A5E00228550-01 99 LOGO! functions 4.2.6 NOR (NOT OR) Symbol in LOGO!: Circuit diagram of a series circuit with several break contacts: The output status of the NOR is only 1 if all inputs are 0, i.e. if switched off. The NOR output is set to 0 when one of the inputs is switched on (logical 1 status). At an unused block input (x): x = 0. Table of the NOR logic 100 1 2 3 4 Q 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 LOGO! Manual A5E00228550-01 LOGO! functions 4.2.7 XOR (exclusive OR) The XOR in a circuit diagram, shown as series circuit with 2 changeover contacts: Symbol in LOGO!: The output status of the XOR is 1 if the inputs are not equivalent. At an unused block input (x): x = 0. Table of the XOR logic 1 2 Q 0 0 1 1 0 1 0 1 0 1 1 0 4.2.8 NOT (Negation, Inverter) A break contact in the circuit diagram: Symbol in LOGO!: The output status is 1 if the input is 0. The NOT block inverts the input status. Advantage of the NOT block, for example: The LOGO! does not require break contacts. You simply use a make contact and the NOT block to convert these into a break contact. Table of the NOT logic 1 Q 0 1 1 0 LOGO! Manual A5E00228550-01 101 LOGO! functions 4.3 Basics on special functions Because of their different input designation, you can see right away that there is a difference between the special functions and basic functions. SFs contain timer functions, retentive functions and various parameter assignment options, which allow you to adapt the circuit program to suit your own requirements. This section provides you with a brief overview of input designations and with some particular background information on SFs. The SFs in particular are described in Chapter 4.4. 102 LOGO! Manual A5E00228550-01 LOGO! functions 4.3.1 Designation of the inputs Logical inputs Here, you will find the description of the connectors you can use to create a logical link to other blocks or to the inputs of the LOGO! unit. S (Set): A signal at input S sets the output to logical "1". R (Reset): The reset input R takes priority over all other inputs and resets the outputs. Trg (Trigger): This input is used to trigger the start of a function. Cnt (Count): This input is used for counting pulses. Fre (Frequency): Frequency signals to be evaluated are applied to this input. Dir (Direction): This input determines the direction of count, for example. En (Enable): This input enables a block function. When this input is "0", other signal from the block will be ignored. Inv (Invert): A signal at this input inverts the output signal of the block. Ral (Reset all): All internal values are reset. Connector X at SF inputs SF inputs connected to connector x are set low. That is, the inputs carry a 'lo' signal. LOGO! Manual A5E00228550-01 103 LOGO! functions Parameter inputs At some of the inputs you do not apply any signals. You configure the relevant block values instead. Examples: Par (Parameter): This input will not be connected. Here, you set the relevant block parameters (times, on/off thresholds etc.). No (Cam): This input will not be connected. Here, you configure the time patterns. P (Priority): This is an open input. Here, you define priorities and specify whether a message is to be acknowledged in RUN. 4.3.2 Time response Parameter T At some of the SFs it is possible to configure a time value T. When you preset this time, note that your input values are based on the timebase set: Timebase __ : __ s (seconds) seconds : 1/ 100 m (minutes) minutes : seconds hours : minutes h (hours) B1 + T =04:10h seconds Setting a time T of 250 minutes: Unit in hours h: 04:00 hours 00:10 hours = 240 minutes +10 minutes 250 minutes Note Always specify a time T in 0.02 s. The time T is not defined for T 0.02 s. 104 LOGO! Manual A5E00228550-01 LOGO! functions Accuracy of T Because of slight tolerances in the characteristics of electronic components, the set time T may deviate. The LOGO! has a maximum tolerance of 0.02 %. When 0.02 % of the time T is smaller than 0.02 seconds, the maximum deviation is 0.02 seconds. Example: The maximum tolerance per hour (3600 seconds) is 0.02 %, which is proportional to 0.72 seconds. The maximum toloerance per minute (60 seconds) is 0.02 seconds. Accuracy of the timer (weekly/yearly timer) To prevent timing inaccuracy of the real-time clock in C versions caused by this deviation, the timer value is continuously compared with a high-precision timebase and corrected. The resultant maximum timing inaccuracy is 5 s/day. 4.3.3 Backup of the real-time clock Because the internal real-time clock of a LOGO! is backed up, it continues operation after a power failure. The ambient temperature influences the backup time. At an ambient temperature of 25C , the typical backup time is 80 hours. 4.3.4 Retentivity The switching states and counter values of SFs can be set retentive. This means that current data are retained after a power failure, and that the block resumes operation at the break point. The timer is not reset, but resumes operation until the time-to-go has expired, for example. To enable this response, however, the relevant functions must be set retentive. Two options are available: R: The data are retained. /: Current data are not retained (default). See the example on Page 72. The hours counter forms an exception, because this function is always retentive. LOGO! Manual A5E00228550-01 105 LOGO! functions 4.3.5 Parameter protection In the parameter protection settings, you can determine whether the parameters can be displayed and edited in LOGO! parameter assignment mode or not. Two options are available: +: The parameter attribute permits read/write access in parameter assignment mode (default). -: The parameter settings are read/write protected in parameter assignment mode, and can be edited only in the programming mode. See the example on Page 72. 4.3.6 Calculating the gain and offset of analog values A sensor is connected to the analog input and converts a process variable into an electrical signal. This value of signal lies within the typical range of this sensor. LOGO! always converts the electrical signals at the analog input into digital values from 0 to 1000. A voltage of 0 to 10 V at input AI is transformed internally into range of values from 0 to 1000. An input voltage exceeding 10 V is shown as internal value 1000. Because you can not always process the range of values from 0 to 1000 as predetermined by LOGO!, you can multiply the digital values by a gain factor and then shift the zero of the range of values (offset). This allows you to output an analog value to the LOGO! display, which is proportional to the actual process variable. Parameter Maximum Input voltage (in V) 0 10 Internal value 0 1000 00.00 10.00 -10000 +10000 Gain Offset 106 Minimum LOGO! Manual A5E00228550-01 LOGO! functions Mathematical rule Actual value Ax = (internal value at input Ax gain) + offset Gain and offset calculation The gain and offset is calculated based on the relevant high and low values of the function. Example 1: The available thermocouples have the following technical data: -30 to +70 C, 0 to 10 V DC (i.e. 0 to 1000 in LOGO!). Actual value = (internal value gain) + offset, thus -30 = (0 A) + B, i.e. offset B = -30 +70 = (1000 A) -30, i.e. gain A = 0.1 Example 2: A pressure sensor converts a pressure of 1000 mbar into a voltage of 0 V, and a pressure of 5000 mbar into a voltage of 10 V. Actual value = (internal value gain) + offset, thus 1000 = (0 A) + B, i.e. offset B = 1000 5000 = (1000 A) +1000, i.e. gain A = 4 LOGO! Manual A5E00228550-01 107 LOGO! functions Example of analog values Process variable Voltage (V) Internal value Gain Offset Value shown (Ax) -30 C 0 C +70 C 1000 mbar 0 3 10 0 0 300 1000 0 0.1 0.1 0.1 4 -30 -30 -30 1000 -30 0 70 1000 3700 mbar 6.75 675 4 1000 3700 5000 mbar 10 1000 4 1000 5000 0 5 10 0 5 10 0 5 10 0 5 10 0 5 10 0 5 10 0 10 0 500 1000 0 500 1000 0 500 1000 0 500 1000 0 500 1000 0 500 1000 0 1000 0.01 0.01 0.01 1 1 1 10 10 10 0.01 0.01 0.01 1 1 1 1 1 1 10 10 0 0 0 0 0 0 0 0 0 5 5 5 500 500 500 -200 -200 -200 -10000 -10000 0 5 10 0 500 1000 0 5000 10000 5 10 15 500 1000 1500 -200 300 800 -10000 0 0.02 0.02 0.02 0.02 2 2 2 2 0.01 0.1 1 10 0 0 0 0 0 0 2 20 A sample application is found in the description of the "Analog comparator" SF on Page 165. For further information on analog inputs, refer to Chapter 4.1. 108 LOGO! Manual A5E00228550-01 LOGO! functions 4.4 Special functions list - SF When you create your circuit program in LOGO!, you find the special function blocks in the SF list. You can invert the inputs of SFs individually, i.e. the circuit program converts a logical "1" at the input into a logical "0"; a logical "0" it converts into a logical "1". An example of the program code found in Chapter 3.6.3. The table also specifies whether the relevant function can be set retentivity (Rem). The following SFs are available: View inLOGO! Name of the special function Rem Times On-delay REM (see page 113) Off-delay REM (see page 117) On-/Off-delay REM (see Page 119) Retentive on-delay REM (see page 121) Wiping relay (pulse output) REM (see page 123) LOGO! Manual A5E00228550-01 109 LOGO! functions View inLOGO! Name of the special function Edge triggered wiping relay Rem REM (see page 125) Asynchronous pulse generator REM (see Page 128) Random generator (see page 130) Stairway lighting switch REM (see page 132) Multiple function switch REM (see page 135) Weekly timer (see Page 138) Yearly timer (see Page 143) 110 LOGO! Manual A5E00228550-01 LOGO! functions View inLOGO! Name of the special function Rem Counter Up/down counter REM (see Page 146) Hours counter REM (see page 150) Threshold trigger Fre (see Page 155) Analog Analog threshold trigger (see page 158) Analog differential trigger (see page 161) Analog comparator (see Page 165) Analog value monitoring (see Page 170) Analog amplifier (see Page 173) LOGO! Manual A5E00228550-01 111 LOGO! functions View inLOGO! Miscellaneous Name of the special function Latching relay Rem REM (see Page 175) Pulse relay REM (see Page 176) Message texts P (see Page 179) Softkey En Par Q REM (see Page 186) Shift register REM (see Page 190) 112 LOGO! Manual A5E00228550-01 LOGO! functions 4.4.1 On-delay Short description The output is only set after a configurable on-delay time has expired. Symbol in LOGO! Wiring Description Input Trg You start the on-delay with a negative edge (1 to 0 transition) at input Trg (Trigger). Parameter T represents the time after which the output is switched on (0 to 1 transition of the output signal). Retentivity: / = no retentivity R = the status is retentive. Output Q Q is switched on when the set time T has expired, provided Trg is still set. Parameter T Please note the defaults for parameter T in Chapter 4.3.2. The time for parameter T can also be preset based on the actual value of another, already configured function. You can use the actual values of the following functions: Analog comparator (actual value Ax - Ay, see Chapter 4.4.18) Analog threshold trigger (actual value Ax, see Chapter 4.4.16) Analog amplifier (actual value Ax, see Chapter 4.4.20) and Counter (actual value Cnt, see Chapter 4.4.13). Select the required function by means of the block number. The timebase is adjustable. Please note the following listing: LOGO! Manual A5E00228550-01 113 LOGO! functions Valid ranges of the timebase, if T = parameter Timebase max. value min. resolution Accuracy s (seconds) 99:99 10 ms + 10 ms m (minutes) 99:59 1s +1s h (hours) 99:59 1 min + 1 min The display in programming mode (example): B12 +R T =04:10h Valid ranges of the timebase, if T = Actual value of an already programmed function Timebase max. value Meaning Accuracy ms 99990 Number of ms + 10 ms s 5999 Number of s +1s m 5999 Number of min + 1 min The display in programming mode (example): B12 +R T B006s If the referenced block (B6, in the example) returns a value that lies out of the valid range, the value is rounded up or down to the next valid value. 114 LOGO! Manual A5E00228550-01 LOGO! functions Parameter preset = Actual value of an already programmed function How to include the actual value of an actual value of an already programmed function: 1. Press ter T. to move the cursor to the equal sign of parame- B12 +R T =04:10h Press twice B12 +R T =04:10h 2. Press to change the equal sign into an arrow. If it exists, the last referenced block and its timebase is shown. B12 +R T B006s 3. Press to move the cursor to the "B" of the shown block, and then press to select the required block number. 4. Press to move the cursor to the block's timebase and press to select the required timebase. B12 +R T B006m The view in parameter assignment mode (example): B12 T =04:10 =04:10h Ta =02:00h LOGO! Manual A5E00228550-01 or current time B12 T B006m Ta =02:00h 115 LOGO! functions Timing diagram Trg Q T T The bold section of the timing diagram is also shown in the on-delay icon. Ta expires Functional description The time Ta is triggered with a 0 to 1 transition at input Trg (Ta is the current LOGO! time). If the status of input Trg is 1 at least for the duration of the configured time T, the output is set to 1 on expiration of this time (the output follows the input with on-delay). The time is reset when the status at input Trg returns to 0 before the time T has expired. The output is reset to 0 when the signal at input Trg is 0. If retentivity is not set, output Q and the expired time are reset after a power failure. 116 LOGO! Manual A5E00228550-01 LOGO! functions 4.4.2 Off-delay Short description When an on-delay is set, the output is reset when the configured time has expired. Symbol in LOGO! Wiring Description Input Trg You start the off-delay time with a negative edge (1 to 0 transition) at input Trg (Trigger) Input R A signal at input R resets the on-delay time and the output. Parameter T is the time that expires after which the output is switched off (1 to 0 transition of the output signal). Retentivity: / = No retentivity R = The status is retentive. Output Q Q is set with a signal at input Trg. It holds this state until T has expired. Parameter T Please note the parameter T defaults specified in Chapter 4.3.2. The time for parameter T can be based on the actual value of another, already configured function. You can use the process variables of the following functions: Analog comparator (actual value Ax - Ay, see Chapter 4.4.18) Analog threshold trigger (actual value Ax, see Chapter 4.4.16) LOGO! Manual A5E00228550-01 117 LOGO! functions Analog amplifier (actual value Ax, see Chapter 4.4.20) and Up/down counter (actual value Cnt, see Chapter 4.4.13). Select the required function by means of the block number. The timebase is configurable. For information on valid timebase ranges and parameter preset, refer to Chapter 4.4.1. Timing diagram Trg The bold section of the timing diagram also appears in the off-delay symbol. R Q Ta expires T T Functional description Output Q is set to hi immediately when the input Trg changes to hi. The actual time Ta in LOGO! is retriggered at the 1 to 0 transition of Trg. The output remains set. Output Q is reset to 0 with off-delay when Ta reaches the value configured at T (Ta=T). The time Ta is retriggered with a one-shot at input Trg. You can set input R (Reset) to reset the time Ta and the output before Ta has expired. If retentivity is not set, output Q and the expired time are reset after a power failure. 118 LOGO! Manual A5E00228550-01 LOGO! functions 4.4.3 On-/Off-delay Short description The on-/off-delay function sets the output after the set ondelay time has expired, and resets it upon expiration of the off-delay time. Symbol in LOGO! Wiring Input Trg Description A positive edge (0 to 1 transition) at input Trg (Trigger) triggers the on-delay time TH . A negative edge (1 to 0 transition) at input Trg (Trigger) triggers the off-delay time TL. Parameter TH is the time after which the output is set hi (output signal transition 0 to 1). TL is the time after which the output is reset ( output signal transition 1 to 0). Retentivity: / = No retentivity R = The status is retentive. Output Q LOGO! Manual A5E00228550-01 Q is set when the configured time TH has expired and Trg is still set. It is reset on expiration of the time TL, if the trigger Trg has not been set again. 119 LOGO! functions Parameters TH and TL Note the preset values for the parameters TH and TL in Chapter 4.3.2. Timing diagram Trg Q TH TH TH The bold section of the timing diagram is also shown in the on/ off-delay symbol. Ta expires TL TL TL Ta expires Functional description The time TH is triggered with a 0 to 1 transition at input Trg. If the status at input Trg is 1 at least for the duration of the time TH, the output is set to 1 on expiration of the time TH (the output follows the input with on-delay). The time is reset when the signal at input Trg is reset to 0 before the time TH has expired.. A 1 to 0 transition at input Trg triggers the time TL. If the status at input Trg is 0 at least for the duration of the signal TL, the output is set to 0 on expiration of the time TL (the output follows the input with off-delay). The time is reset when the signal at input Trg changes to 1 again before the time TL has expired. If retentivity is not set, output Q and the expired time are reset after a power failure. 120 LOGO! Manual A5E00228550-01 LOGO! functions 4.4.4 Retentive on-delay Short description A one-shot at the input triggers a configurable on-delay time. The output is set when this time has expired. Symbol in LOGO! Wiring Description Input Trg A signal at input Trg (Trigger) triggers the on-delay time. Input R A signal at input R resets the on-delay time and the output. Parameter T represents the on-delay time for the output (output status transition 0 to 1). Retentivity: / = no retentivity R = The status is retentive. Output Q Q is set after the time T has expired. Parameter T Note the defaults specified in Chapter 4.3.2. The time for parameter T can be based on the process variable of another, already programmed function. You can use the process variables of the following functions: Analog comparator (actual value Ax - Ay, see Chapter 4.4.18) Analog threshold trigger (actual value Ax, see Chapter 4.4.16) Analog amplifier (actual value Ax, see Chapter 4.4.20) and Up/down counter (actual value Cnt, see Chapter 4.4.13). LOGO! Manual A5E00228550-01 121 LOGO! functions Select the required function by means of the block number. The timebase is configurable. For information on valid ranges and parameter defaults, refer to Chapter 4.4.1. Timing diagram Trg R Q Ta expires T T The bold section of the timing diagram is also shown in the symbol of the retentive on-delay. Functional description The 0 to 1 signal transition at input Trg triggers the current time Ta . Output Q is set when Ta = T. A further signal at input Trg does not influence the time Ta. The output and the time Ta are reset with the next 1 signal at input R. If retentivity is not set, output Q and the expired time are reset after a power failure. 122 LOGO! Manual A5E00228550-01 LOGO! functions 4.4.5 Wiping relay (pulse output) Short description An input pulse generates a signal with a configurable period at the output. Symbol in LOGO! Wiring Description Input Trg A signal at input Trg (Trigger) triggers the time for the wiping relay function. Parameter The output is switched off after the time T has expired (output signal transition 1 to 0). Retentivity: / = No retentivity R = The status is retentive. Output Q A signal at input Trg sets Q. If the input signal = 1, output Q remains set for the time Ta. Parameter T Please note the information on parameter T in Chapter 4.3.2. Timing diagram The bold section of the timing diagram also appears in the symbol of the wiping relay. Trg Q Ta is expiring T T has not expired LOGO! Manual A5E00228550-01 123 LOGO! functions Functional description A 0 to 1 transition at input Trg sets the output, and triggers a time Ta during which the output remains set. Output Q is reset to lo (pulse output) when Ta reaches the value preset at T (Ta = T). The output is immediately reset if there is a 1 to 0 transition at input Trg before the specified time has expired. If retentivity is not set, output Q and the expired time are reset after a power failure. 124 LOGO! Manual A5E00228550-01 LOGO! functions 4.4.6 Edge triggered wiping relay Short description An input pulse generates a preset number of output pulses with a defined pulse/pause ratio (retriggerable), after a configured delay time has expired. Symbol in LOGO! Wiring Description Input Trg A signal at input Trg (Trigger) triggers the times for the edge triggered wiping relay. Input R A signal at input R resets the current time (Ta) and the output. Parameter The interpulse width TL and the pulse width TH are configurable. N determines the number of pulse/pause cycles TL/TH: Range of values: 1...9 Retentivity: / = No retentivity R = The status is retentive. Output Q Q is set after TL has expired, and reset after TH has expired. Parameter T Please note the information on parameter T in Chapter 4.3.2. Timing diagram A Trg Q Ta is running LOGO! Manual A5E00228550-01 TH TH N=1 TL=0 The bold section of the timing diagram also appears in the symbol of the edge triggered wiping relay. 125 LOGO! functions Timing diagram B Trg Timing diagram for the sample configuration Q N=2 TL TH TL TH Functional description A 0 to 1 transition at input Trg triggers the time TL (Time Low). After the time TL has expired, output Q is set for the duration of TH (Time High). If there is a further 0 to 1 transition (retriggering pulse) at input Trg before the preset time (TL + TH) has expired, Ta is reset and the pulse/pause cycle is restarted. If retentivity is not set, output Q and the time are reset after a power failure. Preset of the Par parameter View in programming mode (example): B25 1+R TL =02:00s TH =03:00s Protection mode and retentivity Interpulse width Pulse width Press B25 N =1 126 2 Number of pulse/pause cycles (example) LOGO! Manual A5E00228550-01 LOGO! functions View in parameter assignment mode (example): B25 TL =02:00s TH =03:00s Ta =01:15s LOGO! Manual A5E00228550-01 Current pulse width TL or TH 127 LOGO! functions 4.4.7 Asynchronous pulse generator Short description The output pulse shape can be modified by reconfiguring the pulse/pause ratio. Symbol in LOGO! Wiring Description Input En You can use input EN to set and reset the asynchronous pulse generator. Input INV Input INV can be used to invert the output signal of the active asynchronous pulse generator. Parameter You can configure the pulse width TH and the interpulse width TL. Retentivity: / = No retentivity R = The status is retentive. Output Q Q is set and reset cyclically according to the pulse/ pause ratio TH and TL. Timing diagram En Inv Q TH 128 TL TH TL TH TH TL LOGO! Manual A5E00228550-01 LOGO! functions Functional description You can configure the pulse/interpulse width at the TH (Time High) and TL (Time Low) parameters . Input Inv can be used to invert the output signal, provided the block is enabled with a signal at input EN. If retentivity is not set, output Q and the expired time are reset after a power failure. LOGO! Manual A5E00228550-01 129 LOGO! functions 4.4.8 Random generator Short description The output of the random generator is set or reset within a configured time. Symbol in LOGO! Wiring Input En Description A positive edge ( 0 to 1 transition) at input En (Enable) triggers the on-delay time of the random generator. A negative edge ( 1 to 0 transition) at input En (Enable) triggers the off-delay time of the random generator. Parameter The on-delay is set at random to a value between 0 s and TH. The off-delay is set at random to a value between 0 s and TL. Output Q Output Q is set when the on-delay has expired and if En is still set. It is reset when the off-delay has expired, provided En was not set again meanwhile. Parameter TH and TL Note the defaults of the TH and TL parameters listed in Chapter 4.3.2. 130 LOGO! Manual A5E00228550-01 LOGO! functions Timing diagram En The bold section of the timing diagram also appears in the symbol of the random generator. Q T is busy TH TL Functional description The 0 to 1 transition at input En triggers a random on-delay time between 0 s and TH. The output is set when the ondelay time has expired and if the signal at input En remains hi at least for the duration of this time. The time is reset if input En is reset before the on-delay time has expired. A 1 to 0 transition at input EN triggers a random on-delay time between 0 s and TL. The output is reset after the off-delay time has expired, provided input En remains lo at least for the duration of this time. The time is reset if the signal at input En changes to 1 again before the off-delay time has expired. The time expired is reset after a power failure. LOGO! Manual A5E00228550-01 131 LOGO! functions 4.4.9 Stairway lighting switch Short description An input edge triggers a configurable and retriggerable time. The output is reset after this time has expired. A warning signal can be output before this time has expired to warn of the impending shutdown. Symbol in LOGO! Wiring Description Input Trg A signal at input Trg (Trigger) triggers the off-delay time for the stairway lighting switch. Parameter T represents the off-delay time of the output (output signal transition 1 to 0). T! determines the triggering time for the pre-warning. T!L determines the length of the pre-warning signal. Retentivity: / = No retentivity R = The status is retentive. Output Q Q is reset after the time T has expired. A warning signal can be output before this time has expired. Timing diagram Trg Q T!L Ta is busy T! T 132 LOGO! Manual A5E00228550-01 LOGO! functions Functional description A 0 to 1 signal transition at input Trg sets output Q. The next 1 to 0 transition at Trg retriggers the current time Ta, and output Q remains set. Output Q is reset when Ta = T. You can output a warning signal before the off-delay time (T - T!) has expired to reset Q for the time of the pre-warning period T!L. A further one-shot at input Trg during Ta retriggers the time Ta . If retentivity is not set, output Q and the expired time are reset after a power failure. Preset of the Par parameter Note the defaults specified in Chapter 4.3.2. Note All times must have the same timebase. View in programming mode (example): B9 1+R T =60:00s Protection mode and retentivity Off-delay time Press B9 2 T! =05:00s T!L =00:10s LOGO! Manual A5E00228550-01 Start of the off-warning period (T - T!) Off-warning time 133 LOGO! functions View in parameter assignment mode (example): B9 1 T =60:00s Ta =06:00s 134 Current value of T LOGO! Manual A5E00228550-01 LOGO! functions 4.4.10 Multiple function switch Short description Switch with two different functions: Pulse switch with off-delay Switch (permanent lighting) Symbol in LOGO! LOGO! Manual A5E00228550-01 Wiring Description Input Trg A signal at input Trg (Trigger) sets output Q (permanent light) or resets it with off-delay. When active, output Q can be reset with a signal at input Trg. Input R A signal at input R resets the current time Ta and the output. Parameter T represents the time after which f the output is reset (output signal transition 1 to 0). TL represents the time during which the output must be set to enable the permanent lighting function. T! represents the preset time for the start of the offwarning signal. T!L represents the length of the off-warning period. Retentivity: / = No retentivity R = The status is retentive. Output Q A signal at Trg switches on output Q. Depending on the length of the input at Trg, the output is switched off again or switched on permanently, or it is reset with a further signal at Trg. 135 LOGO! functions Timing diagram Trg TL TL Q T!L Ta is busy T! T Functional description A 0 to 1 transition at input Trg sets output Q. If output Q = 0, and input Trg is set hi at least for the duration of TL, the permanent lighting function is enabled and output Q is set accordingly. The off-delay T is triggered when input Trg returns to 0 before TL has expired. Output Q is reset when Ta = T. You can output an off-warning signal prior to the expiration of the off-delay time (T - T!), to reset Q for the duration of the off-warning signal T!L. A further signal at Trg always resets T and the output Q. If retentivity is not set, output Q and the expired time are reset after a power failure. Preset of the Par parameter Note the defaults specified in Chapter 4.3.2. Note T, T! and T!L must all have the same timebase. View in programming mode (example): B5 1+R T =60:00s TL =10:00s 136 Protection mode and retentivity Off-delay Permanent light on-time LOGO! Manual A5E00228550-01 LOGO! functions Press B5 2 T! =30:00s T!L =20:00s Start of the off-warning period (T - T!) Off-warning time View in parameter assignment mode (example): B5 1 T =60:00s TL =10:00s Ta =06:00s LOGO! Manual A5E00228550-01 Current value of the time TL or T 137 LOGO! functions 4.4.11 Weekly timer Short description The output is controlled by means of a configurable on/off date. The function supports any combination of weekdays. You select the active weekdays by hiding the inactive days. Note Because the LOGO! 24/24o does not have a real-time clock, the weekly timer function is not available for this version. Symbol in LOGO! Wiring Description Cam parameters No1, No2, No3 At the Cam parameters, you set the on- and off-times of the weekly timer for each Cam switch. Here you also configure the days and the time-of-day. Output Q Q is set when the configured cam is actuated. Timing diagram (three examples) Cam 1 21 1 1 1 1 3 1 3 Q Monday Wednesday Friday Sunday Tuesday Thursday Saturday Cam No1: Cam No2: Cam No3: 138 Daily: 06:30 h to 08:00 h Tuesday: 03:10 h to 04:15 h Saturday and Sunday: 16:30 h to 23:10 h LOGO! Manual A5E00228550-01 LOGO! functions Functional description Each weekly timer has three cams you can use to configure a time hysteresis. You specify the on- and off-times at the Cam parameters. The weekly timer sets the output at a certain on-time, if this is not already set. The weekly timer resets the output at a certain off-time, if it is not switched off already. You will cause a conflict if the on- and off-times you set for the weekly timer are identical, though set on different cams. In this case, cam3 takes priority over cam2, whereas cam2 takes priority over cam1. The switching state of the weekly timer is determined by the status of all three cams. Parameter assignment screen form View of the parameter assignment screen form, for example for Cam1: Block B1 Cam No1 B1 1+ D=MTWTFSS On =06:30 Off=08:00 See Showing/hiding parameters - Parameter protection mode on page 72 Weekdays (daily) On-time (06.30 h) Off-time (08:00 h) Weekday The suffix of "D=" (Day) has the following meaning: M: Monday T : Tuesday W: Wednesday T : Thursday F : Friday S : Saturday S : Sunday The uppercase letter indicates: A weekday is selected. A "-" means: A weekday has not been selected. LOGO! Manual A5E00228550-01 139 LOGO! functions On-/Off-times Possible is any time between 00:00 h and 23:59 h. --:-- means: No on-/off-times set. Setting the weekly timer To set the on-/off-times: 1. Move the cursor to one of the Cam parameters of the timer (e.g. No1). 2. Press OK. LOGO! opens the Cam parameter assignment screen form. The cursor is positioned on the weekday. 3. Press and to select one or several weekdays. 4. Press to move the cursor to the first position of the on-time. 5. Set the on-time. Modify the value at the respective position, using the keys and . Move to the cursor to the various positions, using the keys and . At the first position, you can only select the value --:-- (--:-- means: No on-/off-times set). 6. Press to move the cursor to the first position of the off-time. 7. Set the off-time (in same way as in step 5). 8. Confirm your entries with OK. The cursor is now positioned on the No2 parameter (Cam2) and you can configure a further cam. Note For information on timer accuracy, refer to the technical data and to Chapter 4.3.2. 140 LOGO! Manual A5E00228550-01 LOGO! functions Weekly timer: Example The output of the weekly timer switch is to be set daily from 05:30 h to 07:40 h. The output should also be set every Tuesday from 03:10 h to 04:15 h, and at the weekends from 16:30 h to 23:10 h. This requires three cams. Here are the parameter assignment screen forms of the cams No 1, 2 and 3, based on the timing diagram shown earlier. Cam1 Cam No1 must set the output of the weekly timer daily from 05:30 h to 07:40 h. B1 1+ D=MTWTFSS On =05:30 Off=07:40 Cam2 Cam No2 must set the output of the weekly timer every Tuesday from 03:10 h to 04:15 h. B1 2 D=-T----- On =03:10 Off=04:15 LOGO! Manual A5E00228550-01 141 LOGO! functions Cam3 Cam No3 must set the output of the weekly timer switch every Saturday and Sunday from 16:30 h to 23:10 h. B1 3 D=-----SS On =16:30 Off=23:10 Result Cam 1 21 1 1 1 1 3 1 3 Q Monday Wednesday Friday Sunday Tuesday Thursday Saturday 142 LOGO! Manual A5E00228550-01 LOGO! functions 4.4.12 Yearly timer Short description The output is controlled by means of a configurable on/off date. Note Because LOGO! 24/24o does not have a real-time clock, the yearly timer is not available for this version. Symbol in LOGO! Wiring Description Cam parameter At the Cam parameter, you configure the on-/off-times for the cam of the yearly timer. Output Q Q is set when the configured cam is actuated. Timing diagram Feb. Mar. Apr. MM.DD On=02.20 Off=04.03 On Off February 20 at 00:00 h April 3 at 00:00 h Functional description The yearly timer sets the output at a specific on-time, and resets it at a specific off-time. The off-date identifies the day on which the output is reset again. The first value identifies the month, the second the day. For "MM" you can select a placeholder (**), so that the on- and off-time is set for a specific day each month. LOGO! Manual A5E00228550-01 143 LOGO! functions Sample configuration The output of a LOGO! is to be set annually on March 1, reset on April 4, set again on July 7, and reset again on November 19. You need to configure two yearly timers with corresponding on-times. The outputs are then logically linked by means of an OR block B1 + MM-DD On =03-01 Off=04-04 + MM-DD On =07-07 Off=11-19 On-time March 1 Off-time April 4 B2 In addition: On-time July 7 Off-time November 19 Result On B1 B2 Off March 1 at 00:00 h July 7 at 00:00 h April 4 at 00:00 h 144 November 19 at 00:00 h LOGO! Manual A5E00228550-01 LOGO! functions Further examples B11 + **-DD On =**-01 Off=**-02 + **-DD On =**-10 Off=**-20 On-time is the first, and off-time the second day each month. B12 + **-DD On =**-25 Off=**-05 Each month, from the 10th through to the 20th B13 LOGO! Manual A5E00228550-01 In the next month, from the 25th through the 5th 145 LOGO! functions 4.4.13 Up/down counter Short description An input pulse increments or decrements an internal value, depending on the parameter setting. The output is set or reset when a configured threshold is reached. The direction of count can be changed with a signal at input Dir. Symbol in LOGO! Wiring Description Input R A signal at input R resets both the internal count value and the output to zero. Input Cnt The function counts the 0 to 1 transitions at input Cnt. 1 to 0 transitions are not counted. Use inputs I5/I6 for highspeed counting (only LOGO! 12/24 RC/RCo and LOGO! 24/24o): max. 2 kHz. any other input or circuit component for counting low frequency signals (5 Hz). Input Dir You set the direction of count at input Dir: Dir = 0: Up count Dir = 1: Down count 146 LOGO! Manual A5E00228550-01 LOGO! functions Symbol in LOGO! Wiring Parameter Description On: On threshold Range of values: 0...999999 Off: Off threshold Range of values: 0...999999 Retentivity for internal counter value Cnt: / = No retentivity R = The status is retentive. Output Q Q is set or reset, depending on the current value at Cnt and the set thresholds. Timing diagram R Cnt Dir On=Off=5 0 Internal count value Cnt Q Functional description The internal counter increments (Dir = 0) or decrements (Dir = 1) by one count with every positive edge at input Cnt. You can use input R to reset the output and the internal count value to '000000'. As long as R = 1, the output is also lo and the pulses at input Cnt are not counted. If retentivity is not set, output Q and the expired time are reset after a power failure. Q is set or reset depending on the current value at Cnt and the set thresholds. See the calculation rule below. LOGO! Manual A5E00228550-01 147 LOGO! functions Calculation rule If the On threshold Off threshold, then: Q = 1, if Cnt On Q = 0, if Cnt < Off. If the On threshold < Off threshold, then Q = 1, if On Cnt < Off. Default on/off parameters The default limits for the on and/or off parameters can be derived from another, already programmed function. You can use the actual values of the following functions: Analog comparator (actual value Ax - Ay, see Chapter 4.4.18) Analog threshold trigger (actual value Ax, see Chapter 4.4.16) Analog amplifier (actual value Ax, see Chapter 4.4.20) and Up/down counter (actual value Cnt). Select the required function by means of the block number. For information on parameter defaults, refer to Chapter 4.4.1. Note The system scans the counter limit value cyclically. Thus, if the pulse frequency at the fast inputs I5/I6 is faster than the cycle time, the special function might not switch until after the specified limit value is exceeded. Example: Up to 100 pulses per cycle can be counted; 900 pulses have been counted so far. On = 950; Off = 10000. The output is set in the next cycle, after the value has reached 1000. (The output would not be set at all if the value Off = 980.) 148 LOGO! Manual A5E00228550-01 LOGO! functions View in programming mode (example): B3 +R On =001234 Off=000000 or B3 +R On =123456 OffB021 If the referenced block (B6, in the example) returns a value that lies out of the valid range, the value is rounded to the next valid value. The view in parameter assignment mode (example): B3 On =001234 Off=000000 Cnt=000120 LOGO! Manual A5E00228550-01 or Current count value B3 On =123456 OffB021 Cnt=000120 149 LOGO! functions 4.4.14 Hours counter Short description A configured time is triggered with a signal at the monitoring input. The output is set when this time has expired. Symbol in LOGO! Wiring Description Input R A positive edge (0 to 1 transition) at input R resets output Q and sets a configured value MI at the counter for the duration of the time-to-go (MN). Input En En is the monitoring input. LOGO! scans the on-time of this input. Input Ral A positive edge at input Ral (Reset all) resets both the hours counter (OT) and the output, and sets the configured value MI at the counter to for the duration of the time-to-go (MN). That is, output Q = 0, measured operating time OT = 0 and the time-to-go of the maintenance interval MN = MI. 150 LOGO! Manual A5E00228550-01 LOGO! functions Symbol in LOGO! Wiring Parameter Description MI: Maintenance interval to be preset in hour units Range of values: 0000...9999 h OT: Total operating time Range of values: 00000...99999 h Q0: When "R" is selected: Q = 1, if MN = 0; Q = 0, if R = 1 or Ral = 1 When "R+En" is selected: Q = 1, if MN = 0; Q = 0, if R = 1 or Ral = 1 or En = 0. Output Q The output is set when the time-to-go MN = 0. The output is reset: When "Q0:R+En", if R = 1 or Ral = 1 or En = 0 When "Q0:R", if R = 1 or Ral = 1. MI = Configured time interval MN= Time-to-go OT= Total time expired since the last hi signal at input Ral These values are always retentive! LOGO! Manual A5E00228550-01 151 LOGO! functions Timing diagram R En Ral Q MN=MI Par: MI=5h MN=0 OT MI = Configured time interval MN = Time-to-go OT = Total time expired since the last hi signal at input Ral Functional description The hours counter monitors input En. When En = 1, LOGO! computes the time expired and the time-to-go MN. LOGO! shows these times in parameter assignment mode. Output Q is set when the time-to-go MN = 0. A signal at reset input R resets output Q and sets the preset value of MI at the counter for the duration of MN. The hours counter OT continues the count. With a signal at the reset input Ral, you reset output Q and set the preset value of MI at the counter for the duration of MN. The hours counter OT is reset to zero. Depending on your configuration of parameter Q, the output is either reset with a signal at input R or Ral ("Q0:R"), or when a reset signal is set hi, or the En signal is set lo ("Q0:R+En"). 152 LOGO! Manual A5E00228550-01 LOGO! functions Viewing the MI, MN and OT values LOGO! Basic with display unit: You can open the parameter assignment mode when the system is in RUN to view the actual values of MI, MN and OT. LOGO! Basic without display unit: In LOGO!Soft Comfort, you can use the Online Test to read these values (for further information, see Chapter 7). Limit value of OT The value of the operating hours in OT are retained when you reset the hours counter with a signal at input R. The hours counter OT continues the count as long as En = 1, irrespective of the status at the reset input R. The counter limit of OT is 99999 h. The hours counter stops when it reaches this value. In programming mode, you can set the initial value of OT. The counter starts operation at any value other than zero. MN is automatically calculated at the START, based on the MI and OT values (Example: MI = 100, OT = 130, the result is MN = 70). Preset of the Par parameter View in programming mode: B16 + MI = 0100h Q0:R+En OT =00000h or Time expired B16 + MI = 0100h Q0:R OT =00000h MI is the configurable time interval. Its permissible range of values lies between 0 and 9999 hours. LOGO! Manual A5E00228550-01 153 LOGO! functions View in parameter assignment mode: B16 MI = 0100h MN = 0017h OT =00083h 154 Time interval Time-to-go Total operating hours LOGO! Manual A5E00228550-01 LOGO! functions 4.4.15 Threshold trigger Short description The output is set and reset with two configurable threshold triggers. Symbol in LOGO! Wiring Description Input Fre Fre The function counts the 0 to 1 transitions at input Fre. 1 to 0 transitions are not counted. Use inputs I5/I6 for high-speed counting (only LOGO! 12/24 RC/RCo and LOGO! 24/24o): max. 2 kHz. any other input or circuit component for counting low frequency signals (5 Hz). Parameter On: On threshold Range of values: 0000...9999 Off: Off threshold Range of values: 0000...9999 G_T: Time interval or gate time during which the input pulses are measured. Range of values: 00:05 s...99:99 s Output Q Q is set and reset at the thresholds. Timing diagram Q G_T Fre fa = 9 fa = 10 fa = 8 fa = 4 On = 9 Off = 5 fa = Input frequency LOGO! Manual A5E00228550-01 155 LOGO! functions Functional description The threshold trigger measures the signals at input Fre. The pulses are recorded across a configurable time G_T. Output Q is set and reset in accordance with the set thresholds. See the calculation rule below. Calculation rule If the On threshold Off threshold, then: Q = 1, if fa > On Q = 0, if fa Off. If the On threshold < Off threshold, then Q = 1 if On fa < Off. Preset of the Par parameter Note The system scans the counter limit value once per interval G_T. View in programming mode (example): B15 1+ On =0009 Off =0005 Parameter protection mode On threshold Off threshold Press B15 2 G_T=01:00s 156 Time interval for pulses (example) LOGO! Manual A5E00228550-01 LOGO! functions Note The "seconds" timebase is here set as permanent default. When you preset a time G_T of 1 s, the LOGO! returns the current frequency in parameter fa in Hz. View in parameter assignment mode (example): B15 On =0009 Off =0005 fa =0010 On threshold Off threshold Q = 1 (fa > On) Note fa always represents the total pulses measured per time unit G_T. LOGO! Manual A5E00228550-01 157 LOGO! functions 4.4.16 Analog threshold trigger Short description The output is set and reset at two configurable thresholds. Symbol in LOGO! Wiring Input Ax Description You apply the analog signal to be analyzed at input Ax. Use the analog inputs AI1...AI8 (*), the analog flags AM1...AM6, the block number of a function with analog output, or the analog outputs AQ1 and AQ2. Parameter A: Gain Range of values: 00.00...10.00 B: Zero offset Range of values: 10.000 On: On threshold Range of values: 20.000 Off: Off threshold Range of values: 20.000 p: Output Q * 158 Number of decimals Range of values: 0, 1, 2, 3 Q is set or reset by the threshold triggers. AI1...AI8: 0...10 V corresponds with 0...1000 (internal value). LOGO! Manual A5E00228550-01 LOGO! functions Gain and offset parameters Please note the information on gain and offset parameters in Chapter 4.3.6. Parameter p (number of decimals) Does not apply to the display of On, Off and Ax values in a message text. Does not apply to the comparison of On and Off values! (The compare function ignores the decimal point.) Timing diagram 1000 On Off Ax 0 Q Functional description The function fetches the analog signal at input Ax. Ax is multiplied by the value of the A (gain) parameter, and the value at parameter B (offset) is added to product, i.e. (Ax gain) + offset = actual value of Ax. Output Q is set or reset, depending on the set thresholds. See the calculation rule below. Calculation rule If the On threshold Off threshold, then: Q = 1, if the actual value Ax > On Q = 0, if the actual value Ax Off. If the On threshold < Off threshold, then Q = 1 if On actual value Ax < Off. LOGO! Manual A5E00228550-01 159 LOGO! functions Preset of the Par parameter The gain and offset parameters are used to adapt the sensors to the relevant application. View in programming mode (example): B3 1+ On =+04000 Off =+02000 Parameter protection mode On threshold Off threshold Press B3 2 A =01.00 B =+00000 p =2 Gain Offset Decimals in the message text View in parameter assignment mode (example): B3 On =+04000 Off =+02000 Ax =+05000 On threshold Off threshold Q = 1 (Ax > On) View in the message text (example): +050.00 Ax, when p = 2 Q = 1 (Ax > On) 160 LOGO! Manual A5E00228550-01 LOGO! functions 4.4.17 Analog differential trigger Short description The output is set and reset depending on a configurable threshold and a differential value. Symbol in LOGO! Wiring Input Ax Description You apply the analog signal to be analyzed at input Ax. Use the analog inputs AI1...AI8 (*), the analog flags AM1...AM6, the block number of a function with analog output, or the analog outputs AQ1 and AQ2. Parameter A: Gain Range of values: 00.00...10.00 B: Zero offset Range of values: 10.000 On: On/Off threshold Range of values: 20.000 : Differential value for calculating the off parameter Range of values: 20.000 p: Output Q * Number of decimals Range of values: 0, 1, 2, 3 Q is set or reset, depending on the threshold and difference values. AI1...AI8: 0...10 V corresponds with 0...1000 (internal value). LOGO! Manual A5E00228550-01 161 LOGO! functions Gain and offset parameters Please note the information on gain and offset parameters in Chapter 4.3.6. Parameter p (number of decimals) Does not apply to the display of On, Off and Ax values in a message text. Timing diagram A: Function with negative difference O n Off = On + Ax Q Timing diagram B: Function with positive difference Off = On + On Ax Q Functional description The function fetches the analog signal at input Ax. Ax is multiplied by the value of the A (gain) parameter, and the value at parameter B (offset) is added to product, i.e. (Ax gain) + offset = actual value of Ax. Output Q is set or reset, depending on the set (On) threshold and difference value (). The function automatically calculates the Off parameter: Off = On + , whereby may be positive or negative. See the calculation rule below. 162 LOGO! Manual A5E00228550-01 LOGO! functions Calculation rule When you set a negative differential value , the On threshold Off threshold, and: Q = 1, if the actual value Ax > On Q = 0, if the actual value Ax Off. See the timing diagram A. When you set a positive differential value , the On threshold < the Off threshold, and Q = 1, if: On actual value Ax < Off. See the timing diagram B. Preset of the Par parameter The gain and offset parameters are used to adapt the sensors to the relevant application. View in programming mode (example): B3 1+ On =+04000 =-02000 Parameter protection mode On/off threshold Differential value for the on/off threshold Press B3 2 A =01.00 B =+00000 p =2 Gain Offset Decimals in the message text View in parameter assignment mode (example): B3 On =+04000 =-02000 Ax =+05000 LOGO! Manual A5E00228550-01 On threshold Differential value for the off threshold Q = 1 (Ax > On) 163 LOGO! functions Press B3 Off =+02000 164 Off threshold LOGO! Manual A5E00228550-01 LOGO! functions 4.4.18 Analog comparator Short description The output is set and reset, depending on the difference Ax - Ay and on two configurable thresholds. Symbol in LOGO! Wiring Inputs Ax and Ay Description You apply the analog signals whose difference you want to analyze at the inputs Ax and Ay. Use the analog inputs AI1...AI8 (*), the analog flags AM1...AM6, the block number of a function with analog output, or the analog outputs AQ1 and AQ2. Parameter A: Gain Range of values: 00.00...10.00 B: Zero offset Range of values: 10.000 On: On threshold Range of values: 20.000 Off: Off threshold Range of values: 20.000 p: Output Q * Number of decimals Range of values: 0, 1, 2, 3 Q is set or reset, depending on the difference Ax - Ay and the set thresholds.. AI1...AI8: 0...10 V corresponds with 0...1000 (internal value). LOGO! Manual A5E00228550-01 165 LOGO! functions Gain and offset parameters For more information on the gain and offset parameters, refer to Chapter 4.3.6. Parameter p (number of decimals) Does not apply to Ax, Ay, On, Off and values displayed in a message text. Does not apply to the comparison of on and off values! (The compare function ignores the decimal point.) Timing diagram 1000 Ax 0 1000 Ay 0 1000 Ax-Ay 200 0 Q for Ax - Ay > 200, if On = Off = 200 Functional description The function fetches the analog values from the inputs Ax and Ay. Ax and Ay are each multiplied by the value of the A (gain) parameter, and the value at parameter B (offset) is then added to the relevant product, i.e. (Ax gain) + offset = actual value Ax or (Ay gain) + offset = actual value Ay. The function forms the difference ("") between the actual values Ax - Ay. Output Q is set or reset, depending on difference of the actual values Ax - Ay and the set thresholds. See the calculation rule below. 166 LOGO! Manual A5E00228550-01 LOGO! functions Calculation rule If the On threshold Off threshold, then: Q = 1, if: (actual value Ax - actual value Ay) > On Q = 0, if: (actual value Ax - actual value Ay) Off. If the On threshold < Off threshold, then Q = 1, if: On (actual value Ax - actual value Ay) < Off. Preset of the Par parameter The gain and offset parameters are used to adapt the sensors to the relevant application. View in programming mode: B3 1+ On =+00000 Off =+00000 Parameter protection mode On threshold Off threshold Press B3 2 A =00.00 B =+00000 p =0 Gain Offset Decimals in the message text Example In a heating control system, the supply Tv and return line temperatures Tr are to be compared, for example with a sensor at AI2. A control signal is to be triggered (for example "heater On"), when the difference between the supply and return line temperatures is greater than 15 . The control signal is reset when the difference is less than 5 C. The process variable of the temperature is to be shown in parameter assignment mode. LOGO! Manual A5E00228550-01 167 LOGO! functions The thermocouples available have the the following technical data: -30 to +70 C, 0 to 10 VDC. Application Internal mapping -30 to +70 C = 0 to 10 V DC 0 to 1000 0 C 300 Offset = -30 Range of values: 1000 -30 to +70 C = 100 Gain = 100/1000 = 0.1 On threshold = 15 C Threshold = 15 Off threshold = 5 C Threshold = 5 See also Chapter 4.3.6. Configuration (example): B3 1+ On =+00015 Off =+00005 Protection mode On threshold Off threshold Press B3 2 A =00.10 B =-00030 p =0 Gain Offset Decimals in the message text (if used) View in parameter assignment mode (example): B3 1 On =+00015 Off =+00005 168 On threshold Off threshold LOGO! Manual A5E00228550-01 LOGO! functions Press B3 2 Ax =+00010 Ay =-00020 =+00030 Temperature values Q = 1 (differential value > On) View in the message text (example): Ax =+00010 Ay =-00020 Reducing the input response of the analog comparator You can selectively delay the output of an analog comparator by means of the "On-delay" and "Off-delay" special functions. With on-delay, output Q is only set if the pulse width of the triggering signal at input Trg ( =analog comparator output) is longer than the on-delay time. With off-delay, output Q is only reset if the pulse width of the triggering signal at input Trg is longer than the off-delay time. Using this method, you will obtain a virtual hysteresis and reduce the input response to short signals. Function block diagram AI1 AI AI2 AI Analog comparator B1 On-delay A B2 Off-delay B3 Q1 LOGO! Manual A5E00228550-01 169 LOGO! functions 4.4.19 Analog value monitoring Short description This special function saves the process variable of an analog input to memory, and sets the output when the output variable exceeds or drops below this stored value plus a configurable offset. Symbol in LOGO! Wiring Description Input En A positive edge (0 to 1 transition) at input En saves the analog value at input Ax ("Aen") to memory and starts monitoring of the analog range Aen . Input Ax You apply the analog signal to be monitored at input Ax. Use the analog inputs AI1...AI8 (*), the analog flags AM1...AM6, the block number of a function with analog output, or the analog outputs AQ1 and AQ2. Parameter A: Gain Range of values: 00.00...10.00 B: Zero offset Range of values: 10.000 : Difference value for the Aen on/off threshold Range of values: 20.000 p: Output Q * 170 Number of decimals Range of values: 0, 1, 2, 3 Q is set/reset, depending on the stored analog value and the offset. AI1...AI8: 0...10 V corresponds with 0...1000 (internal value). LOGO! Manual A5E00228550-01 LOGO! functions Gain and offset parameters For more information on gain and offset parameters, refer to Chapter 4.3.6. Parameter p (number of decimals) Applies only to the Aen, Ax and values displayed in a message text. Timing diagram En Aen + Aen Aen - Ax Q Functional description A 0 to 1 transition at input En saves the value of the signal at the analog input Ax. This saved process variable is referred to as "Aen". Both the analog actual values Ax and Aen are multiplied by the value at parameter A (gain), and parameter B (offset) is then added to the product, i.e. (Ax gain) + offset = Actual value Aen, when input En changes from 0 to 1, or (Ax gain) + offset = Actual value Ax. Output Q is set when the signal at input En = 1 and if the actual value at input Ax is out of range of Aen . Output Q is reset, when the actual value at input Ax lies within the range of Aen , or when the signal at input En changes to lo. LOGO! Manual A5E00228550-01 171 LOGO! functions Preset of the Par parameter The gain and offset parameters are used to adapt the used sensors to the respective application. View in programming mode: B3 1+ =00000 Parameter protection mode Differential value for the on/off threshold Press B3 2 A =00.00 B =+00000 p =0 Gain Offset Decimals in the message text View in parameter assignment mode (example): B3 =00010 Aen =-00020 Ax =+00005 172 Q = 1 (Ax is out of the range of Aen ) LOGO! Manual A5E00228550-01 LOGO! functions 4.4.20 Analog amplifier Short description This special function amplifies the value of an analog input and outputs the result at an analog output. Symbol in LOGO! Wiring Input Ax Description You apply the analog signal to be amplified at input Ax. Use the analog inputs AI1...AI8 (*), the analog flags AM1...AM6, the block number of a function with analog output, or the analog outputs AQ1 and AQ2. Parameter A: Gain Range of values: 00.00...10.00 B: Zero offset Range of values: 10.000 p: Output AQ * Number of decimals Range of values: 0, 1, 2, 3 This special function has an analog output! This output can only be connected with the analog input of a function or with an analog flag. Range of values for AQ: -32768...+32767 AI1...AI8: 0...10 V corresponds with 0...1000 (internal value). Gain and offset parameters Please note the information on gain and offset parameters in Chapter 4.3.6. Parameter p (number of decimals) Applies only to the AQ value in a message text. LOGO! Manual A5E00228550-01 173 LOGO! functions Functional description The function fetches the analog signal of input Ax. This value is multiplied by the value of the A (gain) parameter, and parameter B (offset) is then added to the product, i.e. (Ax gain) + offset = actual value Ax. The actual value Ax is output at AQ. Preset of the Par parameter The gain and offset parameters are used to adapt the sensors to the relevant application. View in programming mode (example): B3 + A =02.50 B =-00300 p =0 Gain Offset Decimals in the message text View in parameter assignment mode (example): B3 AQ =-00250 174 LOGO! Manual A5E00228550-01 LOGO! functions 4.4.21 Latching relay Short description Input S sets output Q, input R resets output Q again. Symbol in LOGO! Wiring Description Input S You set output Q with a signal at input S. Input R You reset output Q with a signal at input R. If S and R = 1, the output is reset. Parameter Retentivity: / = No retentivity R = The status is retentive. Output Q Q is set with a signal at input S, and reset with a signal at input R. Timing diagram R S Q Switching response A latching relay represents a simple binary element. The output value depends on the status at the inputs and on the previous output status. The following table shows the logic once again: Sn Rn Q 0 0 1 1 0 1 0 1 x 0 1 0 Comment The status is retentive Reset Set Reset (takes priority over Set) When retentivity is enabled, the current status of the output signal is retained after a power failure. LOGO! Manual A5E00228550-01 175 LOGO! functions 4.4.22 Pulse relay Short description A short pulse at the input sets and resets the output. Symbol in LOGO! Wiring Description Input Trg You set and reset output Q with a signal at input Trg (Trigger). Input S You set output Q with a signal at input S. Input R You reset output Q with a signal at input R. Parameter Selection: RS (R input priority) or SR (S input priority) Retentivity: / = No retentivity R = The status is retentive. Output Q Q is set with a signal at Trg, and reset with the next signal at Trg, if S and R = 0. Timing diagram Trg S The bold printed section of the timing diagram is also shown in the symbol for the pulse relay. R Q 176 LOGO! Manual A5E00228550-01 LOGO! functions Functional description Output Q changes its status, i.e. the output is set or reset, with each 0 to 1 transition at input Trg and if the inputs S and R = 0. The signal at input Trg does not influence the special function when S or R = 1. You set the pulse relay with a signal at input S, i.e. the output is set hi. You reset the pulse relay with a signal at input R, i.e. the output is set lo. Status diagram Par Qn-1 S R Trg Qn * 0 0 0 0 0 * 0 0 0 0 ->1 1** * 0 0 1 0 0 * 0 0 1 0 ->1 0 * 0 1 0 0 1 * 0 1 0 0 ->1 1 RS 0 1 1 0 0 RS 0 1 1 0 ->1 0 SR 0 1 1 0 1 SR 0 1 1 0 ->1 1 * 1 0 0 0 1 * 1 0 0 0 ->1 0** * 1 0 1 0 0 * 1 0 1 0 ->1 0 * 1 1 0 0 1 * 1 1 0 0 ->1 1 RS 1 1 1 0 0 RS 1 1 1 0 ->1 0 LOGO! Manual A5E00228550-01 177 LOGO! functions Par Qn-1 S R Trg Qn SR 1 1 1 0 1 SR 1 1 1 0 ->1 1 *: RS or SR **: Triggering signal is effective, because S and R = 0. Depending on your configuration, either input R takes priority over input S (i.e. input S is not effective when R = 1), or vice versa (i.e. input R is not effective when S = 1). After a power failure, the pulse relay and output Q are reset if you have not enabled retentivity. View in programming mode: B29 Par=RS R Press or B29 Par=SR R This special function is not available in parameter assignment mode. Note If Trg = 0 and Par = RS, the special function "Pulse relay" corresponds with the special function "Latching relay" (see Chapter 4.4.21). 178 LOGO! Manual A5E00228550-01 LOGO! functions 4.4.23 Message texts Short description View of a configured message text in RUN mode. Symbol in LOGO! Wiring Description Input En A 0 to 1 transition at input En (Enable) starts the output of the message text. Input P P: Priority of the message text Range of values: 0...30 Quit: Acknowledgment of the message text. Parameter Text: Input of the message text Par:Parameter or actual value of another, already programmed function (see "Visible parameters or process variables") Time: Display of the continuously updated time-ofday Date: Display of the continuously updated date EnTime: Display of the time of the 0 to 1 transition of the signal at input En EnDate: Display of the date of the 0 to 1 transition of the signal at input En Output Q LOGO! Manual A5E00228550-01 Q remains set as long as the message text is set. 179 LOGO! functions Restriction A maximum of 10 message text functions are available. Functional description With the 0 to 1 transition of the signal at input En and when the system is in RUN, the message text you have configured (process variable, text, time-of-day, date) is output to the display. Acknowledgment disabled (Quit = Off): The message text is hidden when the status of the signal at input En changes from 1 to 0. Acknowledgment enabled (Quit = On): When the status of the signal at input En changes from 1 to 0, the message text is output until it is acknowledged with OK. When En = 1, you can not acknowledge the message text. When multiple message text functions are triggered with En=1, the message text that has the highest priority is shown (0 = lowest, 30 = highest). This also means, that a newly activated message text is shown only if its priority is higher than that of previously activated message texts. After a message text is disabled or acknowledged, the function automatically shows the previously active message text that takes the highest priority. You can change the view and the message texts by pressing the keys and . 180 LOGO! Manual A5E00228550-01 LOGO! functions Example This is how tow message texts could be shown: Display field of the LOGO! in RUN mode Motor 5 STOP AT 10:12 !!Action!! Example: Message text with priority 30 Key Motor 2 3000 hours MAINTENANCE! Example: Message text with priority 10 Press Mo 09:00 2003-01-27 Date and current time-of-day (only for versions with real-time clock). Input P configuration To configure the priority and the acknowledgment (programming mode): B33 + Priority 00 Quit=Off "+" means: The parameters and actual values in an active message text can be edited Priority Status of the acknowledgment 1. Increase the priority to 1: 2. Change to 'Quit': 3. Enable 'Quit': LOGO! Manual A5E00228550-01 Cursor on '0' + Press Press or 181 LOGO! functions LOGO! shows: B33 + Priority 01 Quit=On Priority 1 Status of acknowledgment 'On' 4. Confirm the entries with OK Visible parameters or process variables The following parameter or process variables can be displayed in a message text: Special function Parameter or process variable visible in a message text Times On-delay T, Ta Off-delay T, Ta On-/Off-delay Ta, TH, TL Retentive on-delay T, Ta Wiping relay (pulse output) T, Ta Edge triggered wiping relay Ta, TH, TL Asynchronous pulse generator Ta, TH, TL Random generator TH , T L Stairway lighting switch Ta, T, T!, T!L Multiple function switch Ta, T, TL, T!, T!L Weekly timer 3*on/off/day Yearly timer On, Off Counter 182 Up/down counter Cnt, On, Off Hours counter MI, Q, OT LOGO! Manual A5E00228550-01 LOGO! functions Special function Threshold trigger Parameter or process variable visible in a message text fa, On, Off, G_T Analog Analog threshold trigger On, Off, A, B, Ax Analog differential trigger On, , A, B, Ax, Off Analog comparator On, Off, A, B, Ax, Ay, A Analog value monitoring , A, B, Ax, Aen Analog amplifier A, B, Ax Miscellaneous Latching relay - Pulse relay - Message texts - Softkey On/Off Shift register - Changing parameters in the active message text You can allow editing of parameter and process variables in an active message text by entering a "+" in the first line. To prevent changes, enter a "-" sign. When the message text is active, press ESC to select the editing mode. Note You must keep the ESC key pressed at least for one second. Press and to select the relevant line (you can only select lines that contain parameters). Press OK to change the parameter. Use the keys , , and . LOGO! Manual A5E00228550-01 183 LOGO! functions Confirm your changes with OK. You can now edit further parameters in the message text (if any exist). Press ESC to exit editing mode. Key input simulation in the active message text You can enable the four cursor keys C , C , C and C in an active message text by pressing ESC plus the relevant cursor key. Preset of the Par parameter To configure the message text (programming mode): .. .. .. .. Parameter assignment screen form for Par Press to select a line for the message text. Press and to select the relevant type of message text (Text, Par, Time...). Confirm with OK. Further entries are required when "Text" or "Par" are selected: Press and to select the letter to be displayed in the text. To move the cursor from one position to the other, press and . The list of available characters is here the same as for the circuit program name. The character set is found in Chapter 3.6.4. Press OK to confirm your changes, and press ESC to exit the editing mode. To output a parameter (e.g. a process variable or function value) as message text, select the relevant line with and then press : Par .. .. .. 184 LOGO! Manual A5E00228550-01 LOGO! functions Press OK to open the editing mode: B01>T Press and to select the blocks to be displayed and the corresponding parameters. Press and to select the block or parameter you want to view. Select the parameter by pressing OK. Press ESC to exit the parameter assignment mode and to apply your changes. LOGO! Manual A5E00228550-01 185 LOGO! functions 4.4.24 Softkey Short description This special function has the effect of a mechanical pushbutton or switch. Symbol in LOGO! En Par Wiring Description Input En Output Q is set with a 0 to 1 transition of the signal at input En (Enable), and if 'Switch=On' was confirmed in parameter assignment mode. Parameter Programming mode: Selecting the function for pushbutton action for the duration of one cycle, or for switching action. Q Start: On or off state, initialized at the first start of the program if retentivity is disabled. Retentivity: / = No retentivity R = The status is retentive. Parameter assignment mode (RUN mode): Switch: Switches the momentary pushbutton or switch on or off. Output Q Switches on if En=1 and Switch=On was confirmed with OK. Factory setting The default setting at 'Par' is 'Momentary pushbutton' action. 186 LOGO! Manual A5E00228550-01 LOGO! functions Timing diagram En Switch Q Functional description In parameter assignment mode, the output is set with a signal at input En, if the ''Switch' parameter is set to 'On' and confirmed with OK. Whether the function was configured for pushbutton or switching action is here of no concern. The output is reset to '0' in the following three cases: After a 0 to 1 transition at input En. When the function was configured for momentary pushbutton action, and one cycle has expired since it was switched on. When the position 'Off' was selected at the 'Switch' parameter and confirmed with OK in parameter assignment mode. If retentivity is not set, output Q is initialized after a power failure according to your configuration at the "Start" parameter. Preset of the Par parameter View in programming mode (example): 1. Select the 'Softkey' function. 2. Select input En and confirm with OK. The cursor is now positioned below 'Par'. 3. Change to the input mode of 'Par': Confirm with OK (the cursor is now positioned to 'On') B33 +/ On= Start=On LOGO! Manual A5E00228550-01 The status is not retentive The function is set for 'momentary pushbutton' action Q is set in the first cycle after the program start 187 LOGO! functions To change 'Par' to 'Switch' action and the initialization status after the program start: 4. To select 'Momentary pushbutton' or 'Switch' action: Press or B33 +/ On/Off Start=On The status is not retentive 'Switch' function Q is set in the first cycle after the program start 5. To change to the start state: 6. To change the start state: B33 +/ On/Off Start=Off Press Press or or The status is not retentive 'Switch'function Q is reset in the init cycle after the program start 7. Confirm your entries with OK View in parameter assignment mode (example): Here, you can set or reset the 'Switch' parameter (On/Off). When in RUN, the LOGO! shows the following display: B33 Switch=Off The pushbutton/switch is here switched off Let us assume you want to set 'Switch' (On). 1. Change to the editing mode: Confirm with OK (the cursor is now positioned on 'Off') 2. To change from 'Off' to 'On': Press or 3. Confirm your entries with Press OK 188 LOGO! Manual A5E00228550-01 LOGO! functions B33 Switch=On LOGO! Manual A5E00228550-01 The momentary pushbutton/switch is here switched on 189 LOGO! functions 4.4.25 Shift register Short description You can use the shift register function to read the value of an input and to shift its bits left or right. The output value corresponds with the configured shift register bit. The shifting direction can be changed at a special input. Symbol in LOGO! Wiring Description Input In Input read at the start of the function. Input Trg A positive edge (0 to 1 transition) at input Trg (Trigger) starts the special function. 1 to 0 transitions are irrelevant. Input Dir The signal at input Dir determines the shifting direction for the shift register bits S1...S8 an: Dir = 0: Shift up (S1 >> S8) Dir = 1: Shift down (S8 >> S1) Parameter Shift register bit that determines the value at output Q. Possible settings: S1 ... S8 Retentivity: / = No retentivity R = The status is retentive. Output Q 190 The output value corresponds with the configured shift register bit. LOGO! Manual A5E00228550-01 LOGO! functions Functional description The function reads the value at input In with a positive edge (0 to 1 transition) at input Trg (Trigger). This value is applied to shift register bit S1 or S8, depending on the shifting direction: Shift up: The value at input In is set at S1; the previous value at S1 is shifted to S2; the previous value at S2 is shifted to S3 etc. Shift down: The value at input In is set at S8; the previous value at S8 is shifted to S7; the previous value at S7 is shifted to S6 etc. Output Q returns the value of the configured shift register bit. If retentivity is disabled, the shift function restarts at S1 or S8 after a power failure. When enabled, retentivity always applies to all shift register bits. Note The special function shift register can be used only once in the circuit program. Timing diagram In Trg Q Dir S1 S2 S3 S4 S5 S6 S7 S8 0 0 0 0 1 1 0 0 1 0 0 0 0 1 1 0 Shift up LOGO! Manual A5E00228550-01 0 1 0 0 0 0 1 1 1 0 1 0 0 0 0 1 1 1 0 1 0 0 0 0 0 1 1 0 1 0 0 0 1 1 0 1 0 0 0 1 S4 = Q (example) Shift down 191 LOGO! functions Preset of the Par parameter View in programming mode: B3 Q=S8 R Retentivity enabled Preset Press B3 Q=S7 R etc. You can select S8...S1. This special function is not available in parameter assignment mode. 192 LOGO! Manual A5E00228550-01 5 Configuring LOGO! When speaking of 'parameter assignment', we refer to the configuration of the block parameters. You can set delay times for time functions, the switching times of the timers, the counter threshold value, the monitoring interval of an hours counter and the on and off thresholds of the trigger. You can configure the parameters In programming mode In parameter assignment mode In programming mode, the author of the circuit program also sets the parameters. We have added the parameter assignment mode to allow the editing of parameters without having to modify the circuit program. This feature is available for the user to edit parameters, without having to change to programming mode, for example. The advantage: The circuit program remains protected, but can be adapted by the user to meet specific requirements. Note In parameter assignment mode, the LOGO! continues execution of the circuit program. LOGO! Manual A5E00228550-01 193 Configuring LOGO! 5.1 Selecting parameter assignment mode Press ESC to change from RUN to parameter assignment mode: Mo 09:00 2003-01-27 ... Press ESC Note The following applies to earlier device versions up to 0BA2: You open parameter assignment mode by pressing ESC+OK. LOGO! changes to parameter assignment mode and opens the parameter assignment menu: >Stop Set Param Set Clock Prg Name 194 LOGO! Manual A5E00228550-01 Configuring LOGO! Description of the four menu items of the parameter assignment menu Stop You select this command to stop your circuit program and thus change to the main menu of programming mode. To do so: 1. To move the '>' cursor to 'Stop': Press or 2. To confirm 'Stop': Press OK Stop Prg >No Yes 3. To move the '>' cursor to 'Yes': Press or 4. To confirm 'Yes': Press OK LOGO! shows the main menu of the programming mode: >Program.. Card.. Clock.. Start Set Param For information on the various parameters, refer to the Chapters 5.1.1 to 5.1.3. Set clock The 'Set Clock' command is only executed if your LOGO! is equipped with a real-time clock (LOGO!..C). You set the real-time clock of LOGO! by means of the 'Set Clock' command. For details, refer to Chapter 5.2. Prg Name This menu command only allows you to read the name of your circuit program. It is not possible to modify this name in parameter assignment mode. (see Chapter 3.6.4.) LOGO! Manual A5E00228550-01 195 Configuring LOGO! 5.1.1 Parameters Note In the following discourse on parameters, we presume that the respective default parameter protection mode ("+") has been maintained. This is prerequisite for viewing and editing parameter in the parameter assignment mode! See Chapter 4.3.5 and the example on Page 72. Parameters are, for example: The delay times of a timer relay. The switching times (cams) of a timer switch. Counter thresholds The monitoring time for hour counters The trigger thresholds. Each one of the parameters is identified by its block number (Bx) and the shortname of the parameter. Examples: T: ...is a configurable time. MI: ...is a configurable time interval. Note LOGO!Soft Comfort also allows you to assign names to blocks (for more information, refer to Chapter 7). 196 LOGO! Manual A5E00228550-01 Configuring LOGO! 5.1.2 Selecting the parameters To select a parameter: 1. On the parameter assignment menu, select 'Set Param': Press or Stop >Set Param Set Clock Prg Name 2. Confirm with OK. LOGO! shows the first parameter. If no parameter can be set, you can press ESC to return to the parameter assignment menu. Block number B9 1 T =60:00s Display number for functions with several displays Ta =06:00s The current time in the LOGO! No Param Press ESC No parameters for editing: Press ESC to return to the paramete ment menu The value set at parameter T (Time) 3. Now, select the desired parameter: Press or . 4. Select the parameter you want to edit, and press OK. LOGO! Manual A5E00228550-01 197 Configuring LOGO! 5.1.3 Modifying parameters You first select the parameter you want to edit (see Chapter 5.1.2). You change the value of the parameter in the same way as you did in programming mode: 1. Move the cursor to the point at which you want to make the change: Press or 2. To change this value: Press or 3. To apply the value: OK B9 T =80:00s Ta =06:00s Change: Press or Move: Press or Done: OK Note Alongside with a change of the time parameters when the system is in RUN, you can also change the timebase (s = seconds, m = minutes, h = hours). This does not apply if the time parameter represents the result of another function (for an example, see Chapter 4.4.1). In this case you can neither change the value nor the timebase. The current time is reset to zero when you change the timebase. Current value of a time T View of a time T in parameter assignment mode: B9 T =80:00s Configured time T Ta =06:00s Current time Ta You can change the configured time T. 198 LOGO! Manual A5E00228550-01 Configuring LOGO! Current timer value View of a timer cam in parameter assignment mode: B1 1 D=M-W-F-- On = 09:00 Off=10:00 You can change the on/off times and the day. Current value of a counter View of a counter parameter in parameter assignment mode: B3 On =001234 Off=000000 Cnt=000120 or Current count value B3 On =123456 OffB021 Cnt=000120 You can change the on/off threshold. This does not apply if the on or off threshold represents the result of another function (in the example, this is B21, see Chapter 4.4.13). Current value of an hour counter View of an hour counter parameter in parameter assignment mode: B16 MI = 0100h MN = 0017h OT =00083h Time interval Time-to-go Total operating hours You can edit the configured time interval MI. LOGO! Manual A5E00228550-01 199 Configuring LOGO! Current value of a threshold trigger View of the parameter of a threshold trigger in parameter assignment mode: B15 On =0009 Off =0005 fa =0010 On threshold Off threshold Process variable You can change the on/off threshold. 200 LOGO! Manual A5E00228550-01 Configuring LOGO! 5.2 Setting the time-of-day and date (LOGO! ... C) You can set the TOD and the date In parameter assignment mode In programming mode. To set the TOD and the date in parameter assignment mode: 1. Select parameter assignment mode. (see Chapter 5.1.) 2. On the parameter menu, select 'Set Clock' (Press or ), and then press OK. Set Clock Mo 15:30 YYYY-MM-DD 2003-01-27 The cursor is positioned on the weekday. 3. Select the day of the week: Press or 4. Move the cursor to the next position: Press or 5. To change the value: Press or 6. To set the correct TOD, repeat steps 4 and 5. 7. To set the correct date, repeat steps 4 and 5 8. To confirm your entries: Press OK To set the TOD and the date in programming mode: 1. Select programming mode (ESC / >Stop). (see Chapter 3.6.1.) 2. On the main menu, select 'Clock..' (Press or ), and then press OK. 3. Go to the clock menu, and select 'Set Clock' (Press or ), and the press OK. You can now set the weekday and the time as described earlier (as of step 3.). LOGO! Manual A5E00228550-01 201 Configuring LOGO! 202 LOGO! Manual A5E00228550-01 6 LOGO! program module (card) LOGO! allows you to store only one circuit program in its memory. If you want to modify the circuit program or create a further one without deleting the first, you must archive it somewhere. One of the options is to use a program module/card. The circuit program stored in LOGO! can be copied to a program module (card). You can then insert the program module/card in another LOGO! to copy the circuit program. using the program module (card), you can: Archiving circuit programs Reproducing circuit programs Send circuit programs by mail Write and test your circuit program at the office, and then transfer it to a LOGO! in the switching cabinet. LOGO! is supplied with a hood. The program module (card) is supplied separately. Note You do not need a module to backup the circuit program in your LOGO!. The LOGO! circuit program is automatically stored in nonvolatile memory when you exit the programming mode. We shall now introduce the program module (Card) you can order for LOGO! The card can backup all data in the LOGO! circuit program memory. The order number is found in the appendix. LOGO! Manual A5E00228550-01 203 LOGO! program module (card) Compatibility ... to current versions (0BA4 devices): Data written to the program module (card) in a 0BA4 version can be read in all other 0BA4 versions. ... to earlier versions (0BA0 to 0BA3 devices): A program module (card) that contains data written in earlier versions (0BA0...0BA3 devices) can not be used in LOGO! devices of the 0BA4 generation. When the LOGO! system detects such an 'old' program module (card), the message "Unknown Card / Press ESC" is output to the display. Vice versa, an 0BA4 program module (card) can not be used in LOGO! devices of the 0BA0...0BA3 family. Upward compatibility of circuit programs Circuit programs written for the previous versions 0BA0...0BA3 can only be applied in 0BA4 units by means of LOGO!Soft Comfort. 204 LOGO! Manual A5E00228550-01 LOGO! program module (card) 6.1 Security function (CopyProtect) We principally distinguish between program modules (card) with and without circuit program/copy protection. Unprotected program module (card) You can edit circuit programs without restrictions, and exchange data between the program module (Card) and the device. Protected program module (card) A circuit program is protected when it is transferred from a protected program module (card) to the LOGO!. To execute this circuit program in LOGO!, the protected program module (card) must remain inserted during RUN, i.e. the circuit program stored on the program module (card) can not be copied to other LOGO! devices. Over and above that, a protected circuit program is write- protected. A circuit program with password protection is no longer protected after the correct password has been entered, i.e. you can then edit the program and remove the module. Note You need to assign a password when you create the circuit program for a protected module (card) to be able to edit it at a later time (see Chapter 3.6.5). LOGO! Manual A5E00228550-01 205 LOGO! program module (card) Correlation between the password and the protective function Password Protection Editing Copying Deleting - - Yes Yes Yes Yes - Yes, with password Yes Yes, with password - Yes No No Yes Yes Yes Yes, with password Yes, with password Yes, with password Assigning a security function To assign a circuit program and copy protection function to the program module (card), open the programming mode and select "Card". 1. Switch the LOGO! to programming mode (ESC / >Stop). 2. The main menu opens. To select the 'Card' command: Press or 3. To apply you entry in 'Card': Press OK 4. Move the '>' cursor to 'CopyProtect': Press or 5. To apply 'CopyProtect': Press OK LOGO! shows the following display: >No Yes CopyProtect: No The current protection setting is shown in the bottom line. This function is disabled by default ("No": disabled). 206 LOGO! Manual A5E00228550-01 LOGO! program module (card) Enabling the security function To set the security function: 1. Move the '>' cursor to 'Yes': 2. Confirm 'Yes': LOGO! shows the following display: Press or Press OK >No Yes CopyProtect: Yes Note This only generates a circuit program and copy protection for the program module (card); the circuit program itself must be copied separately from the LOGO! to the program module (card) (can also be done initially). You can always change the "No" status (security function disabled) to "Yes" (security function enabled). A status change from "Yes" (security function enabled) to "No" (security function disabled) is only possible if the program module (card) does not contain a circuit program. LOGO! Manual A5E00228550-01 207 LOGO! program module (card) 6.2 Inserting and removing the program module (card) When you remove a program module (card) with circuit program and copy protection attribute, note the following: The circuit program stored on the program module (card) can only be executed if the card remains inserted during system runtime. After you have removed the program module (card), LOGO! outputs the message'No Program'. A removal of the program module (card) during RUN will lead to impermissible operating states. Always heed the following warning: ! Warning Do not touch the open slot of the program module (card) neither with your fingers, nor with a metallic or conductive object. The program module (card) socket may be under voltage if the polarity is reversed at L1 and N by accident. The program module (card) may only be removed by qualified personnel. 208 LOGO! Manual A5E00228550-01 LOGO! program module (card) Removing the program module (card) To remove the program module (card): Carefully insert a screwdriver into the groove on the upper end of the program module (card) and lever the module partially out of the slot. You can now remove the program module (card). Inserting a program module (card) The entry of the program module (card) slot is chamfered on its bottom right. The edge of the program module (card) is chamfered accordingly. This encoding prevents you from inserting the program module (card) the wrong way round. Insert the program module (card) into the slot and push it in until it engages. LOGO! Manual A5E00228550-01 209 LOGO! program module (card) 6.3 Copying data from the LOGO! to the program module (card) To copy the circuit program to the program module (card): 1. Insert the program module (card) into the slot. 2. Switch the LOGO! to programming mode (ESC / >Stop). >Program.. Card.. Clock.. Start LOGO! main menu 3. The main menu opens. To select the 'Card' command: Press or 4. Press OK. The transfer menu opens. > Card Card CopyProtect = LOGO! 5. Move the '>' cursor to 'LOGO Card' (if required) Press or 6. Press OK. LOGO! now copies the circuit program to the program module (card). When LOGO! has finished copying, it automatically returns you to the main menu: >Program.. Card.. Clock.. Start The circuit program backup is now stored on your program module (card) and you can remove the card. Do not forget to replace the cap. 210 LOGO! Manual A5E00228550-01 LOGO! program module (card) If power fails while LOGO! is copying the circuit program, repeat the process after Power On. Note The password X of a protected circuit program in LOGO! also applies to the copied program version on your program module (card). LOGO! Manual A5E00228550-01 211 LOGO! program module (card) 6.4 Copying data from the program module (card) to LOGO! You have a program module (card) that contains your circuit program. There are two ways to copy it to LOGO!: Automatically during the startup of LOGO! (POWER ON) or by means of the "Card" menu of LOGO!. Note If the program on the module/card is protected with the password X, the copied program in the LOGO! is also protected with the same password. Automatic copying during the startup of LOGO! Proceed as follows: 1. Switch off the power supply to the LOGO! (POWER OFF) 2. Remove the slot cover. 3. Insert the program module/card into the relevant slot. 4. Switch on the power supply to the LOGO! LOGO! copies the program from the program module/card to LOGO!. When LOGO! has finished copying, it opens the main menu: >Program.. Card.. Clock.. Start 212 LOGO! Manual A5E00228550-01 LOGO! program module (card) Note Before you switch the LOGO! to RUN, you must ensure that the system you are controlling with LOGO! does not represent a source of hazard. 1. Move the '>' cursor to 'Start': 2. Press OK. Press or Copying by means of the "Card"menu For information on the replacement of a program module (card), also note Chapter 6.2. To copy a program from the program module (card) to LOGO!: 1. Insert the program module (card) 2. Switch the LOGO! to programming mode (ESC / >Stop). >Program.. Card.. Clock.. Start 3. Move the '>' cursor to 'Card': Press or 4. Press OK. The transfer menu opens. 5. Move the '>' cursor to 'Card LOGO': Press or Card >Card CopyProtect = LOGO! 6. Press OK. LOGO! copies the circuit program from the program module (card) to LOGO!. When LOGO! has finished copying, it automatically returns to the main menu. LOGO! Manual A5E00228550-01 213 LOGO! program module (card) 214 LOGO! Manual A5E00228550-01 7 LOGO! Software LOGO!Soft Comfort is available as a programming package for the PC. This software provides many features, for example: A graphic interface for offline creation of your circuit program by means of Ladder Diagram (contact chart / circuit diagram) or Function Block Diagram (function chart) Simulation of your circuit program on the PC Generating and printing of an overview chart for the circuit program Saving a backup of the circuit program on the hard drive or other media Comparing circuit programs Easy configuration of blocks Transferring the circuit program - from the LOGO! to the PC and - from the PC to LOGO! Reading the values of the hour counter Setting the TOD Summertime/wintertime conversion Online test: Display of status changes and process variables of LOGO! in RUN mode: - Status of a digital I/O, flags, shift register bits and cursor keys - The values of all analog I/Os and flags - The results of all blocks - The current values (including the times) of selected blocks Stopping circuit program execution via the PC (STOP). LOGO! Manual A5E00228550-01 215 LOGO! Software The LOGO! alternative As you can see, LOGO!Soft Comfort represents an alternative to conventional engineering methods: 1. You start by developing the circuit program on your desktop. 2. You simulate the circuit program on your computer and verify its functions, before you actually implement it in your system. 3. You can add comments to the circuit program and create hardcopies. 4. You save a copy of your circuit program to the file system on your PC, to make it directly available for any modifications. 5. It takes only a few key actions to download the circuit program to LOGO!. LOGO!Soft Comfort LOGO!Soft Comfort allows you the efficient, easy and concise creation of your circuit programs on the PC ("Wiring by means of Softkey"). After you have created the circuit program, you can either let the system decide which LOGO! version it requires for your program, or predetermine the relevant LOGO! version for the circuit program. Particularly user-friendly functions are; Offline program simulation Simultaneous display of the status of several special functions Extensive options of circuit program documentation Display of the states and process variables of LOGO! in RUN mode a comprehensive Online Help. 216 LOGO! Manual A5E00228550-01 LOGO! Software LOGO!Soft Comfort runs under Windows 95/98, Windows NT 4.0, Windows Me, Windows 2000, Windows XP, Linuxand Mac OS X. LOGO!Soft Comfort is capable of client/server operation and offers you a high degree of freedom and comfort for creating your circuit program. LOGO!Soft Comfort V4.0 This is the current version of LOGO!Soft Comfort. You will find all the functions and the functionality of the devices described in this manual in the version 4.0 and later. Updating LOGO!Soft Comfort versions V1.0 up to V3.0 The update can only be installed for the full version of LOGO!Soft Comfort V1.0, V2.0 or V3.0. order numbers are found in Appendix E. Updates and info You can download demo versions of the software free of charge from the Internet address specified in the preface. LOGO! Manual A5E00228550-01 217 LOGO! Software 7.1 Connecting the LOGO! to a PC Connecting the PC cable To connect the LOGO! to a PC, you need the LOGO! PC cable (order number is found in Appendix E). Remove the cap or program module (card) from your LOGO! and connect the cable to this socket. Connect the other end of the cable to the serial port of your PC. Connecting the PC cable to the USB port If your PC is only equipped with a USB interface (Universal Serial Bus), you will need a converter and a device driver to connect the LOGO! cable to this port. Follow the instructions on the screen when you install the driver for the converter.Make sure you specify the correct Windows OS version when you select the driver. Switching LOGO! to PC LOGO mode 1. Switch the LOGO! with/without display to STOP from your PC (refer to the LOGO!Soft Comfort Online Help), or select the ESC / >Stop command on a device with display and confirm the entry with 'Yes'. When LOGO! is in STOP and online with the PC, the following PC commands are accepted: Switch LOGO! to RUN Read/write the circuit program Read/write the summertime/wintertime 2. When you start the upload/download in STOP, the following display appears automatically: PC 218 = LOGO! LOGO! Manual A5E00228550-01 LOGO! Software Note Earlier versions up to 0BA3 with/without display are automatically switched to PC LOGO mode as follows: 1. Switch off the power supply to the LOGO!. 2. Remove the cover or the program module (card) and connect the cable to this socket. 3. Switch on power. LOGO! switches automatically to PC LOGO mode. The PC can now access the LOGO! For information on this function, refer to the LOGO!Soft Comfort Online Help. For more information on LOGO! versions without display, refer to Appendix C. Closing the PC LOGO mode When the data transfer is completed, the connection to the PC is shut down automatically. Note If the circuit program created with LOGO!Soft Comfort is password protected, both the circuit program and the password are downloaded to LOGO!. The password prompt is enabled at the end of the data transfer. The upload of a password protected program created in LOGO! is only possible after the correct password is entered in LOGO!Soft Comfort. LOGO! Manual A5E00228550-01 219 LOGO! Software 220 LOGO! Manual A5E00228550-01 8 Applications We have provided a small collection of applications in this manual to give you an impression of the versatility of LOGO!. For these examples we have recorded once again the original solution of the circuit diagram, and compared it with the LOGO! solutions. You can find solutions for the following tasks: Page Stairway or corridor lighting system 223 Automatic door 227 Ventilation system 234 Factory gate 239 Central controlling and monitoring of several factory gates 243 Luminous rows 247 Service water pump 251 Further applications 255 LOGO! Manual A5E00228550-01 221 Applications Note LOGO! applications are available to all our customers free of charge. The examples provided are noncommittal, serve as general information about the fields of application for LOGO!, and may be different to user-specific solutions. The user operates the system at his own responsibility. We refer to the relevant national standards and system-related installation regulations. Although you have four inputs available for logic operations (basic functions, see Chapter 4.2), the following figures will only show a maximum of three inputs for reasons of clarity. You program this fourth input and assign parameters just like the other three inputs. Errors can not be ruled out, and the right to make changes is reserved. These application and tips for further applications are also found on the Internet under the URL specified earlier in the preface. 222 LOGO! Manual A5E00228550-01 Applications 8.1 Stairway or corridor lighting 8.1.1 Requirements for a stairway lighting system The basic requirements for a stairway lighting system are as follows: When someone is using the stairway, the lighting should be switched on. If no-one is in the stairway, the lights should be switched off in order to save energy. 8.1.2 Previous solution The two conventional options for switching the lights: With a pulse relay With an automatic stairway lighting switch The wiring of both these lighting systems is identical. III III III III Lights Distribution box Distribution with pulse relay or Pushbuttons automatic stairway lighting switch Components used Momentary switches Automatic stairway lighting switch or pulse relay LOGO! Manual A5E00228550-01 223 Applications Lighting system with pulse relay Function of a lighting system with pulse relay: Press any pushbutton: The lighting is switched on Press any of the pushbuttons once again: The lighting is switched off. Disadvantage: People often forget to switch off the lights. Lighting system with an automatic stairway lighting switch Function of a lighting system with automatic stairway lighting switch: Press any pushbutton: The lighting is switched on The lights are switched off automatically when the preset time has expired. Disadvantage: The lights can not be switched on for a longer period of time (e.g. when cleaning the stairway). The switch for permanent lighting is usually located on the automatic stairway lighting switch and may be difficult or impossible to access. 8.1.3 Lighting system with LOGO! A LOGO! system allows you to replace the automatic stairway lighting switch or the pulse relay. You can also implement both functions (timed off-delay and pulse relay) in a single unit. What is more, you can incorporate extra functions without making any alterations to the wiring. Here are some examples: Pulse relay with LOGO! Automatic stairway lighting switch with LOGO! Multiple function switch with LOGO! - Switch light on - Switch on permanent lighting - Switch light off 224 LOGO! Manual A5E00228550-01 Applications Wiring of a lighting system with LOGO! 230RC II II II II Lamps N L PE L1 N I1 I2 I3 I4 I1 I5 I3 I6 I7 I8 Switches Q1 Q2 Q3 Q4 The external wiring of a lighting system with a LOGO! is no different than it is for a conventional stairway and corridor lighting system. Only the automatic stairway lighting switch/ pulse relay is replaced. Supplementary functions are entered directly in LOGO!. Pulse relay with LOGO! Switch:I1 x Q1 Lamps Output Q1 is toggled with a pulse signal at input I1. Automatic stairway lighting switch with LOGO! Momentary I1 switch: T 06:00m Q1 Lights Output Q1 is set for the duration of 6 minutes with a pulse signal at input I1. LOGO! Manual A5E00228550-01 225 Applications Multiple function switch with LOGO! Switch: I1 TH / TL Q1 Lights Output Q1 is set for the duration of a preset time TH with a pulse signal at input I1. The permanent lighting function is enabled by keeping the momentary switch pressed for a specified time TL. 8.1.4 Special features and expansion options Other options for increasing comfort or saving energy are, for example: A flashing function that indicates that the light is about to be switched off automatically. You can integrate various central functions: - Central off - Central on (panic button) - Control of all lamps or individual circuits by means of a daylight control switch - Controlling by means of an integrated timer (e.g. permanent lighting only until 24.00 h; disabled at specific times) - Automatically switching off the permanent lighting on expiration of a preset time (e.g. after 3 hours) 226 LOGO! Manual A5E00228550-01 Applications 8.2 Automatic door You often find automatic door control systems at the entrance to supermarkets, public buildings, banks, hospitals etc. 8.2.1 Requirements of an automatic door When a person approaches the door, it must open automatically. The door must remain open until the doorway is cleared. When the doorway is cleared, the door must close automatically with a short delay. Outside Motion detector B1 NNNNNIIIII S1 Inside Limit switch S2 closed B2 Motion detector Limit switch open Q1 Master switch Motion detector NNNNIIII NNNNIIII NNNNIIII NNNNIIII NNNNIIII NNNNIIII NNNNIIII NNNNIIII Master switch The door is usually driven by a motor that is equipped with a slip coupling. This prevents people from being squeezed in and injured. The control system is connected to the mains via a master switch. LOGO! Manual A5E00228550-01 227 Applications 8.2.2 Conventional solution Auxiliary circuit L1 S2 K3 S2 K3 B1 B2 S1 K2 K1 N Open K3 K4 Close B1 B2 K1 K2 K3 K3 K4 Open door Waiting time When someone enters the detection range of one of the motion sensors B1 or B2, the door opening motion is initiated by setting K3. After the detection range of the two motion sensors has been cleared at least for a minimum time, K4 enables the closing motion. 8.2.3 Door control system with LOGO! LOGO! can simplify this circuit considerably. You only need to connect the motion sensors, limit switches and the contactor relays to the LOGO! . 228 LOGO! Manual A5E00228550-01 Applications Wiring of a door control system with LOGO! 230RC L1 S1 B1 L1 N 1 Q1 2 K1 I1 I2 I3 I4 1 S2 B2 Q2 2 I5 I6 I7 1 Q3 2 1 I8 Q4 2 K2 N Open Close Components used K1 K2 S1 (break contact) S2 (break contact) B1 (make contact) B2 (make contact) LOGO! Manual A5E00228550-01 contactor relay open contactor relay Close limit switch Closed limit switch Open infrared motion sensor outside infrared motion sensor inside 229 Applications Door control system with LOGO!circuit diagram 1 I1 I2 x RS Open 1 I4 x Q1 I4 & 1 & Q2 T= 4s & Q2 I3 1 Close Q1 This is what the circuit diagram of the conventional solution looks like. You can simplify this circuit if you make use of the LOGO! functions. You can use the off-delay function to replace the latching relay and the on-delay. The block diagram below illustrates this simplification: Motion detector 1 I1 I2 x & Q2 Q1 Open x 10 s Limit switch I4 Door open 1 & Limit switch Door closed Q2 I3 Close 1 Q1 230 LOGO! Manual A5E00228550-01 Applications 8.2.4 Special features and expansion options Options for increasing comfort and user friendliness are, for example: You can connect an additional control switch with the positions: Open - Automatic - Closed (O-A-C) You can connect a buzzer to an output of the LOGO! to warn of the closing of the door. You can enable opening of the door time and directiondependent, i.e. opening only during business hours, and opening only from the inside after closing time. 8.2.5 Extended solution with LOGO! 230RC Wiring the LOGO! extended solution L1 B1 B2 L1 N 1 Q1 S1 S2 I1 I2 I3 I4 2 K1 1 Q2 K2 2 S3 I5 I6 I7 1 Q3 2 1 O-A-C I8 Q4 2 H1 N Open LOGO! Manual A5E00228550-01 Close Buzzer 231 Applications Block diagram of the extended LOGO! solution Cam1: Day= Mo..Fr On = 09:00 Off =18:00 Cam2: Day= Sa On = 08:00 Off =13:00 Detecting motion x x I1 Motion detector B1 x T= 10 s Cam1: Day= Mo..Fr On = 09:00 Off =19:00 Cam2: Day= Sa On = 08:00 Off =14:00 x I2 Motion detector B2 Actuate motor for opening Close output Q2 Q1 Open x Limit switch Door open Control switch Door open I4 I5 Actuate motor for closing Limit switch Door closed I3 Open output Motion detector B1 Motion detector B2 Q1 I1 I2 Control switch Close door 232 x Q2 Close I6 LOGO! Manual A5E00228550-01 Applications Detecting motion During business hours, the motion detector B1 initiates the opening of the door when somebody wants to enter the shop. Motion detector B2 initiates the opening of the door when somebody wants to leave the shop. After closing time, the motion detector B2 continues to be used to open the door for 1 hour to allow the customers to leave the shop. Actuating the motor for opening Output Q1 is set and opens the door when: The control switch at I5 is actuated (the door is permanently open), or The motion detectors indicate that somebody is approaching the door, and The door has not yet fully opened (limit switch at I4). Actuating the motor for closing Output Q2 is set to close the door when: The control switch at I6 is actuated (the door is permanently closed) or The motion detectors indicate that there is nobody near the door, and The door has not yet fully closed (limit switch at I3). Buzzer Connect the buzzer to output Q3. The buzzer gives a brief warning (in this case 1 second) when the door is closing. Enter the following circuit at Q3 in the circuit program: Q2 Close output x Q3 Buzzer T= 1 s LOGO! Manual A5E00228550-01 233 Applications 8.3 Air-conditioning System 8.3.1 Requirements for an air-conditioning System The air-conditioning system supplies fresh air to a room or exhausts the contaminated air from a room. Let us examine following example: EEEEEEEEEEEEEEEEEE EEEEEEEEEEEEEEEEEE EEEEEEEEEEEEEEEEEE EEEEEEEEEEEEEEEEEE EEEEEEEEEEEEEEEEEE EEEEEEEEEEEEEEEEEE EEEEEEEEEEEEEEEEEE EEEEEEEEEEEEEEEEEE EEEEEEEEEEEEEEEEEE EEEEEEEEEEEEEEEEEE Fresh-air fan Flow sensor Flow sensor Exhaust fan The room is equipped with an exhaust fan and a fresh 234 air fan. Both fans are monitored by means of a flow sensor. An excess atmospheric pressure may never develop in the room. The fresh-air fan must only be switched on if safe functioning of the exhaust fan is signaled by the flow sensor. A warning lamp indicates failure of a fan. LOGO! Manual A5E00228550-01 Applications The circuit diagram for conventional solutions is as follows: Auxiliary circuit L1 S0 S1 K1 K2 K5 K4 K5 S2 S2 v> K1 N S3 v> K2 K3 K4 Exhaust air H1 K5 H2 Operation Error Fresh air The fans are monitored by means of flow sensors. If no air flow is registered within a short waiting time, the system is switched off and an error message is output. This message can be acknowledged by pressing the OFF button. In addition to the flow sensors, the fan monitoring system also requires an evaluating circuit with several switching devices. This evaluating circuit can be replaced by a single LOGO! unit. Wiring of an air-conditioning system with LOGO! 230RC L1 S1 S0 S2 v> L1 N I1 I2 I3 I1 I4 1 N Q1 K1 2 1 K2 Exhaust fan LOGO! Manual A5E00228550-01 Q2 S3 v> I3 I5 I6 I7 I8 2 1 Q3 H1 2 1 Q4 2 H2 Fresh-air fan 235 Applications Components used K1 K2 S0 (break contact) S1 (make contact) S2 (make contact) S3 (make contact) H1 H2 contactor relay contactor relay STOP pushbutton START pushbutton flow sensor flow sensor signal lamp signal lamp Block diagram of the LOGO! solution The block diagram of the air-conditioning system with LOGO! : On I1 Error Q3 Q1 Exhaust fan x Off I2 Exhaust fan Q1 x Exhaust fan Exhaust air flow sensor Q1 Exhaust air flow sensor x I3 Fresh-air fan I3 Q2 Fresh-air fan x T= 10 s Q2 x x Fresh-air flow sensor I4 x T= 10 s Off 236 I2 Q3 Error LOGO! Manual A5E00228550-01 Applications 8.3.2 Advantages of using LOGO! The LOGO! solution requires less switchgear. That saves you installation time and space in the control cabinet. You might even be able to use a smaller switching cabinet. Additional LOGO! options The free output (Q4) can be used as isolated signal contact for reporting faults or power failure. It is possible to switch off of the fans by means of a sequential circuit. These functions can be implemented without additional switchgear. Block diagram of the extended LOGO! solution The fans at Q1 and Q2 are switched on and off by means of the following circuit: On I1 Fault Q3 Q1 Exhaust fan I2 Off T= 30 s x Exhaust air flow sensor I3 x x T= 10 s Q1 exhaust fan Exhaust air flow sensor I3 Q2 Fresh-air fan x T= 10 s x Fresh-air fan Q2 x Fresh-air flow sensor I4 T= 10 s Off LOGO! Manual A5E00228550-01 I2 Q3 Error 237 Applications You can also generate a message at output Q4: Q3 Error Q4 Message The relay contacts of output Q4 are always closed when the system is in operation. Relay Q4 does not drop off unless there is a power failure or a fault in the system. This contact can be used for remote monitoring, for example. 238 LOGO! Manual A5E00228550-01 Applications 8.4 Factory door OO OO OO OO OO OO OO OO Safety pressure bar OO OO OO OO OO OO OO OO Indicator lamp The entrance to a company's premises is often closed with a gate. The gate is only opened to let vehicles in and out. The gate is controlled by the porter. 8.4.1 Requirements for a gate control system The gate is opened and closed by means of pushbuttons in the gatehouse. The porter can monitor the operation of the gate at the same time. The gate is normally fully opened or fully closed. The gate motion can be interrupted at any time. An indicator lamp is switched on five seconds before the gate starts moving and when the gate is in motion. A safety pressure bar prevents harm to persons and objects from getting trapped or damaged when the gate is closing. LOGO! Manual A5E00228550-01 239 Applications 8.4.2 Previous solution Various control systems are used to operate automatic gates. The circuit diagram below shows one of these options. Auxiliary circuit L1 S0 S1 K1 S2 K3 K1 K3 S2 S1 S5 p> K3 S5 p> K1 S3 K2 S4 K1 N K2 K4 K6 K3 K4 Open K5 H1 Indicator lamp Close K5 K6 Open Close Wiring of a gate control system with LOGO! 230RC L1 S3 S4 p> S5 S0 Stop S1 OpenS2 Close L1 N 1 Q1 I1 2 I2 1 I3 I4 Q2 2 I5 1 Q3 2 I6 I7 1 I8 Q4 2 S5 p> N K1 Open 240 K3 H1 Close Indicator lamp LOGO! Manual A5E00228550-01 Applications Components used K1 K2 S0 (break contact) S1 (make contact) S2 (make contact) S3 (break contact) S4 (break contact) S5 (break contact) contactor relay contactor relay STOP pushbutton OPEN pushbutton CLOSE pushbutton Position sensor OPEN Position sensor CLOSED Safety bar Block diagram of the LOGO! solution Q2 Start pushbutton OPEN Start pushbutton I2 CLOSED I1 T= 5s STOP I3 pushbutton Gate is open I4 x Q1 Open x CLOSE pushbutton TH= TL=2 s Inv=lo Q1 Q3 Signal lamp x STOP pushbutton CLOSE pushbutton I2 OPEN pushbutton I1 Safety bar I3 I6 Gate is closed I5 T= 5s Q2 Close x The OPEN or CLOSE pushbuttons initiate the gate motion, provided it is not already moving in the other direction. The gate is stopped by means of the STOP pushbutton or the relevant limit switch. A safety bar furthermore interrupts the closing motion of the gate. LOGO! Manual A5E00228550-01 241 Applications 8.4.3 Extended LOGO! solution Our extended control circuit is to open the gate automatically when the safety bar is actuated. Safety bar I6 x Q2 x x STOP pushbutton I3 Gate is open I4 Q1 Open T= 5s Q2 x OPEN pushbutton I1 Q1 x CLOSE pushbutton I2 STOP pushbutton I3 Safety bar I6 Gate is closed I5 242 TH= TL=2 s Inv=lo T= 5s Q3 Signal lamp Q2 Close LOGO! Manual A5E00228550-01 Applications 8.5 Centralized control and monitoring of several factory doors 1 1 1 1 Safety bar 2 flashing warning light OO OO OO OO OO OO OO OO OO OO 2 Door I AS interf. 2 AS Door II interf. Master O O O O O O O O O O 2 Door III AS interf. Often, a company's premises can be entered at several locations. Not all of the gates can always be monitored locally by personnel. They must therefore be able to be monitored and operated by the porter who sits in a central gatehouse. It must also be possible for a member of staff to open and close the gate locally. For each gate we are going to use one LOGO! 230RC and one communication module AS interface. The modules and the master are interconnected by means of a bus system. This chapter describes a gate control system. The structures of the other gate control systems are identical. LOGO! Manual A5E00228550-01 243 Applications 8.5.1 Requirements for a gate control system Every gate is opened and closed by means of a cord operated switch. The gate is will be fully opened or fully closed. All gate can be opened and closed locally by means of pushbuttons. The gate can be opened and closed at the gatehouse by means of the bus system. The GATE OPEN or GATE CLOSED status is indicated. An indicator lamp is switched on five seconds before the gate starts moving and when the gate is in motion. A safety pressure bar prevents harm to persons and objects from getting trapped or damaged when the gate closes. Wiring of the gate control system with LOGO! 230RC and CM AS interface L1 p> S0 L1 N S1 I1 S2 S3 I2 I3 S4 I4 S5 I5 S6 I6 I7 I8 AS interface 1 2 1 Q1 2 Q2 1 2 1 Q3 2 Q4 p> S6 K1 K2 N Gate 244 Gate Indicator lamp LOGO! Manual A5E00228550-01 Applications Components used K1 K2 S0 (make contact) S1 (make contact) S2 (make contact) S3 (make contact) S4 (break contact) S5 (break contact) contactor relay open contactor relay Close cord operated switch OPEN cord operated switch CLOSE OPEN pushbutton CLOSE pushbutton position sensor GATE IS OPEN position sensor GATE IS CLOSED S6 (break contact) Safety bar Master control system Q5 Q6 I9 I10 LOGO! Manual A5E00228550-01 position sensor GATE IS OPEN position sensor GATE IS CLOSED external pushbutton OPEN GATE external pushbutton CLOSE GATE 245 Applications Block diagram of the LOGO! solution I5 I1 I9 Gate is open & 1 Open gate Open gate 1 x Q1 x x I5 Gate is open I3 I5 Open gate by hand Gate is open T= 5s Open gate & x I4 I6 I7 I6 1 & =1 Q2 T= 5s Gate is closed Gate is closed Safety bar Gate is open Close gate & x I5 x x I2 Close 1 Closed I10 x I7 Safety bar I6 I7 & Close gate by hand Gate is closed Safety bar 1 & Q3 x TH= TL=2 s Inv=lo Indicator lamp Q5 Open Close I6 Gate is closed Q6 The OPEN GATE and CLOSE GATE pushbuttons initiate the gate motion, provided it is not already moving in the other direction. The gate motion ends at the respective limit switch. Closing of the gate is also interrupted by the safety bar. 246 LOGO! Manual A5E00228550-01 Applications 8.6 Luminous rows EE EEEEEEEEEEEE E EE EEEEEEEEEEEE E EEEEEEEEEEEE EEEEEEEEEEEE EEEEEEEEEEEE EEEEEEEEEEEE EEEEEEEEEEEE EEEEEEEEEEEE EEEEEEEEEEEE EEE EEEE EEEEEEEEEEEE EEEEEEEEEEEEEEEEE EEEEEEEEEEEEEEEEE Luminous rows 1 Luminous rows 2 Luminous rows 3 Luminous rows 4 Office Corridor When planning lighting systems for commercial locations, the type and number of lamps used is determined by the luminance required. For reasons of cost efficiency, the installation often consists of fluorescent tubes arranged in luminous rows, and are divided into separate switching circuits, according to the way the room is used. 8.6.1 Requirements for a lighting system The various luminous rows are switched on and off locally. If there is sufficient daylight, the rows on the window side of the room are automatically switched off by means of a daylight control switch. The lights are switched off automatically at 20.00 h. Local manual operation of the lighting must be possible at all times. LOGO! Manual A5E00228550-01 247 Applications 8.6.2 Previous solution L1 lx> B1 E1 K1 K1 K2 S1 S2 K3 K4 K2 S3 S4 K3 K4 K5 K6 K5 K6 E2 E3 E4 E5 E1 K2 N The lamps are switched on and off with pulse relays, by means of pushbutton control at the door. Regardless of this, they are reset with a timer or daylight control switch signal at the central off input. The pulse width of the off commands must be reduced by means of wiping relays to allow operation of the lights after they are switched off. Components required: Pushbuttons S1 to S4 Daylight control switch B1 Timer E1 Wiping relays K1 and K2 Pulse switches K3 to K6 with central OFF function Disadvantages of the previous solution A substantial amount of switchgear needs to be installed to implement the necessary functions. Due to the large number of mechanical components, high wear and tear and maintenance expenditure is to be expected. The modification of functions involves considerable effort. 248 LOGO! Manual A5E00228550-01 Applications 8.6.3 Luminous row control system with LOGO! 230RC L1 S1 S2 S3 lx< S4 B1 L1 N I1 1 Q1 2 I2 I2 1 I3 Q2 I1 I4 2 I3 I3 I5 1 Q3 I6 2 I4 I7 1 I8 Q4 2 I5 N Luminous row 1 Luminous row 2 Luminous row 3 Luminous row 4 Components used S1 to S4 (make contact) momentary pushbutton B1 (make contact) daylight control switch LOGO! Manual A5E00228550-01 249 Applications Block diagram of the LOGO! solution Off pulse triggered with timer Mo..Su 20:00 - 20.01 Mo..Su 21:00 - 21.01 T= 1s I3 Luminous row 3 Corridor side Q3 I4 Luminous row 4 Corridor side Q4 I1 Luminous row 1 Window side Q1 I2 Luminous row 2 Window side Q2 x Off pulse triggered with daylight control switch Daylight control switch I5 T= 1s x I5 x x Advantages of the LOGO! solution You can connect the lamps directly to the LOGO!, provided the power consumption does not exceed the switching capacity of the various outputs. Higher loads should be switched with a contactor relay. Connect the daylight control switch directly to an input of the LOGO! . You do not need an external timer, because this function is integrated in the LOGO! . Due to the reduced amount of switchgear, you can install a smaller and space-saving distribution cabinet. Fewer devices are required The lighting system can be easily modified. Additional switching times can be set as required (sequential circuit for the off pulses at the end of the day). The function of the daylight control switch can be easily applied to all lamps or to a modified group of lamps. 250 LOGO! Manual A5E00228550-01 Applications 8.7 Service water pump The use of rainwater as an addition to the drinking water supply is gaining importance in the domestic housing area. This saves money and helps to protect the environment. For example, rainwater can be used for: Washing clothes Irrigation system for gardens Watering indoor plants Car wash Toilet flushing installations The sketch below illustrates how such a rainwater utilization system is operated: Rainwater supply line K4 Drinking water supply line III III III OOO III OOO SSS OOO SSS Pressure switch S1 Control in the distribution box Pump M1 Rainwater reservoir S2 S3 S4 Pressure tank Service water connection Drinking water supply Off Drinking water supply On Dry-run protection Off Dry-run protection On The rainwater is collected in a reservoir. From the reservoir, a pumping station supplies a respective line system. From there it can be tapped in the same way as normal drinking water. If the reservoir should run dry it can be topped up with drinking water. LOGO! Manual A5E00228550-01 251 Applications 8.7.1 Requirements for a control system of a service water pump Service water must be available at all times. In case of emergency, the control system must automatically switch over to drinking water supply. When switching over to the drinking water supply, the ingress of rainwater into the drinking water system must be prevented. The service water pump may not be switched on if the reservoir has run low of rainwater (dry-run protection). 8.7.2 Previous solution Auxiliary circuit L1 K3 S3 S1 p< K2 K1 N Pump K2 S4 S2 K3 K3 Tracking time Dry-run protection S3 K4 K4 Y1 Drinking water supply line The pump and a solenoid valve are controlled by means of a pressure switch and 3 float switches, which are installed in the rainwater reservoir. The pump must be switched on when the pressure level in the boiler drops below minimum. After the operating pressure is reached, the pump is switched off again after a tracking time of a few seconds has expired. The tracking time prevents oscillation of the water pump if water is drawn off over a longer period of time. 252 LOGO! Manual A5E00228550-01 Applications 8.7.3 Service water pump system with LOGO! 230RC L1 S1 p< L1 N S3 S2 I1 I2 I3 1 Q1 2 1 Q2 2 K1 Y1 I4 S4 I5 1 Q3 2 I6 I7 I8 1 Q4 2 N Pump Drinking water supply line Apart from the LOGO!, all you need is a pressure switch and the float switches to control the pump. If you are using a 3-phase AC motor, you must use a contactor relay to switch the pump. For single-phase AC pump systems you must provide a contactor relay if the power consumption of the AC motor exceeds the capacity of the output relay Q1. The power consumption of a solenoid valve is usually low enough to allow direct controlling. K1 contactor relay Y1 solenoid valve S1 (make contact) pressure switch S2 (make contact) float switch S3 (break contact) float switch S4 (break contact) float switch LOGO! Manual A5E00228550-01 253 Applications Block diagram of the LOGO! solution Pressure switch I1 x T = 20 s Float switch for dryrun protection OFF x Pump Q1 I3 Float switch for dryI4 run protection ON Float switch for drinking water supply ON Drinking water supply line Q2 I3 Float switch for drinking water supply OFF I2 8.7.4 Special features and expansions The block diagram shows how you can interconnect the pump controls and the solenoid valve. The layout corresponds with the circuit diagram. You also have the option to integrate further functions for specific applications, which can only be implemented in a conventional circuitry by adding further switchgear, e.g.: Enabling the pump at specific times Indication of imminent or existing water shortage Reporting of system faults 254 LOGO! Manual A5E00228550-01 Applications 8.8 Further fields of application In addition to the application samples shown above, we have placed further sample applications on the Internet (see the preface for the URL). There you can find, for example: Irrigation system for greenhouse plants Conveyor control system Bending machine control system Shop window lighting Bell system (e.g. in a school) Parking lot surveillance Outdoor lighting Shutter control system Domestic outdoor and indoor lighting system Control system of a cream stirrer Sports hall lighting Constant load on 3 consumers Sequential control system for cable-welding machines for large cross-sections Step switch (e.g. for fans) Sequential control for boilers Control system for several pump sets with centralized operator control Cutting device (e.g. for detonating fuses) Monitoring periods of utilization, e.g. of a solar energy system Intelligent foot switches, e.g. for speed preselection) Elevating platform controls Impregnation of textiles, heating and conveyor belt controls Silo-filling system and lots more. LOGO! Manual A5E00228550-01 255 Applications On the Web you can also find descriptions and the corresponding circuit diagrams of the applications. You can read these *.pdf files with the Adobe AcrobatReader. If you have installed LOGO!Soft Comfort on your computer, you can simply click the disk icon to download the relevant circuit programs, which you can then adapt to suit your application and download to the LOGO! directly via the PC cable. Benefits of LOGO! LOGO! is a particularly useful feature For replacing auxiliary switchgear with the integrated LOGO! functions For saving wiring and installation work - because LOGO! keeps the wiring "in its head". For reducing space requirements for components in the control cabinet/distribution box. A smaller control cabinet/distribution box may provide sufficient space. For adding or changing functions, without having to install additional switchgear or change the wiring. For offering your customers new, additional functions for domestic and commercial housing installations. Examples: - Domestic security systems: LOGO! switches on a lamp at regular intervals or opens and closes the shutters while you are on holiday. - Central heating: LOGO! runs the circulation pump only when water or heating is actually required. - Refrigerating systems: LOGO! can defrost refrigerating systems at regular intervals to save energy costs. - You can illuminate aquaria and terraria on a time-dependent basis. Last not least you can: Use commonly available switches and pushbuttons, which makes it easy to install a domestic system. Connect LOGO! directly to your domestic installation; the integrated power supply makes it possible. 256 LOGO! Manual A5E00228550-01 Applications Do you want more Info? For more information about LOGO!, see our web page (see the preface for the URL). Do you have any suggestions? There are definitely many more useful applications for the LOGO! . If you know of one, why not write to us? We will collect all the suggestions made and distribute as many of them as we can. No matter whether your LOGO! circuit is particularly complex or simple, simply write to us. We shall be delighted to receive all your suggestions. Write to: Siemens AG A&D AS SM MA PO box 48 48 D-90327 Nuremberg LOGO! Manual A5E00228550-01 257 Applications 258 LOGO! Manual A5E00228550-01 A Technical data A.1 General technical data Criterion Tested in accordance with LOGO!Basic: Dimensions (WxHxD) Weight Values 72 x 90 x 55 mm Approx. 190 g Installation on a 35 mm profile rail 4 module widths or wall mounting LOGO! expansion module: Dimensions (WxHxD) 36 x 90 x 55 mm Weight Approx. 90 g Installation on a 35 mm profile rail 4 module widths or wall mounting Climatic conditions Ambient temperature Horizontal installation Vertical installation Low temperature to IEC 60068-2-1 High temperature to IEC 60068-2-2 -- 40 C ... +70 C Storage/shipping Relative humidity IEC 60068-2-30 From 10 to 95 % no condensation 795 ... 1080 hPa IEC 60068-2-42 IEC 60068-2-43 SO2 10 cm3 /m3, 4 days H2S 1 cm3 /m3, 4 days Air pressure Pollutants LOGO! Manual A5E00228550-01 0 ... 55 C 0 ... 55 C 259 Technical data Criterion Tested in accordance with Values Ambient mechanical conditions Protection mode IP20 Vibrations: IEC 60068-2-6 5 ... 9 Hz (constant amplitude 3.5 mm) 9 ... 150 Hz (constant acceleration 1 g) Shock IEC 60068-2-27 18 shocks (half-sine wave 15g/11 ms) Drop IEC 60068-2-31 Drop height 50 mm Free fall (packaged) IEC 60068-2-32 1m Electromagnetic compatibility (EMC) Noise emission EN 55011/A EN 55022/B EN 50081-1 (domestic area) Limit class B group 1 Electrostatic discharge IEC 61000-4-2 Severity 3 IEC 61000-4-3 8 kV air discharge 6 kV contact discharge Field strength 10 V/m IEC 61000-4-6 10 V IEC 61000-4-4 Severity 3 IEC 61000-4-5 Severity 3 2 kV (supply and signal lines) 1 kV (power lines) symmetrical 2 kV (power lines) asymmetrical IEC 60664, IEC 61131-2, EN 50178 cULus to UL 508, CSA C22.2 No. 142 With LOGO! 230 R/RC, also VDE 0631 IEC 61131-2 Fulfilled Electromagnetic fields HF currents on cables and cable shielding Burst pulses High-energy surge pulse (applies only to LOGO! 230 ...) Safety to IEC / VDE Clearance and creepage distance rating Insulation strength 260 Fulfilled LOGO! Manual A5E00228550-01 Technical data A.2 Technical data: LOGO! 230... and LOGO! DM8 230R LOGO! 230 RC LOGO! 230 RCo LOGO! DM8 230R Input voltage 115...240 V AC/DC 115...240 V AC/DC Permissible range 85 ... 265 V AC 100 ... 253 V DC 85 ... 265 V AC 100 ... 253 V DC Permissible mains frequency 47 ... 63 Hz 47 ... 63 Hz 115 V AC 10 ...40 mA 10 ... 30 mA 240 V AC 10 ... 25 mA 10 ... 20 mA 115 V DC 5 ... 25 mA 5 ... 15 mA 240 V DC 5 ... 15 mA 5 ... 10 mA Power supply Power consumption Voltage failure buffering 115 V AC/DC 240 V AC/DC typ typ. y 10 ms typ typ. y 10 ms typ 20 ms typ. typ 20 ms typ. 115 V AC 1.1 ... 4.6 W 1.1 ... 3.5 W 240 V AC 2.4 ... 6.0 W 2.4 ... 4.8 W 115 V DC 0.5 ... 2.9 W 0.5 ... 1.8 W 240 V DC 1.2 ... 3.6 W 1.2 ... 2.4 W Power loss at Backup of the real-time clock at 25 C typ. 80 h Accuracy of the real-time clock typ. 2 s / day Digital inputs Number 8 4 Electrical isolation No No LOGO! Manual A5E00228550-01 261 Technical data LOGO! 230 RC LOGO! 230 RCo LOGO! DM8 230R Signal 0 < 40 V AC < 40 V AC Signal 1 > 79 V AC > 79 V AC Signal 0 < 30 V DC < 30 V DC Signal 1 > 79 V DC > 79 V DC < 0.03 mA < 0.03 mA 0 08 mA > 0.08 0 08 mA > 0.08 0 to 1 1 to 0 typ. y 50 ms typ. y 50 ms typ. 50 ms typ. 50 ms Line length (unshielded) 100 m 100 m Number 4 4 Output type Relay outputs Relay outputs Electrical isolation Yes Yes In groups of 1 1 Control of a digital input Yes Yes Continuous current Ith max. 10 A per relay max. 5 A per relay 230/240 V AC 1000 W 1000 W 115/120 V AC 500 W 500 W Fluorescent tubes with ballast (25000 switching cycles) 10 x 58 W (at 230/240 V AC) 10 x 58 W (at 230/240 V AC) Fluorescent tubes, conventionally compensated (25000 switching cycles) 1 x 58 W (at 230/240 V AC) 1 x 58 W (at 230/240 V AC) Input voltage L1 Input current at Signal 0 Signal 1 Delay time at Digital outputs Incandescent lamp load (25000 switching cycles) at 262 LOGO! Manual A5E00228550-01 Technical data LOGO! 230 RC LOGO! 230 RCo LOGO! DM8 230R Fluorescent tubes, uncompensated (25000 switching cycles) 10 x 58 W (at 230/240 V AC) 10 x 58 W (at 230/240 V AC) Short circuit-proof cos 1 Power protection B16 600A Power protection B16 600A Short-circuit proof cos 0.5 to 0.7 Power protection B16 900A Power protection B16 900A Derating none; across the entire temperature range none; across the entire temperature range Parallel output circuits for power increase Not permitted Not permitted Protection of output relay (if desired) max. 16 A, characteristic B16 max. 16 A, characteristic B16 Mechanical 10 Hz 10 Hz Ohmic load/lamp load 2 Hz 2 Hz Inductive load 0.5 Hz 0.5 Hz Switching rate LOGO! Manual A5E00228550-01 263 Technical data A.3 Technical data: LOGO! 24... and LOGO! DM8 24 LOGO! 24 LOGO! 24o LOGO! DM8 24 Input voltage 24 V DC 24 V DC Permissible range 20.4 ... 28.8 V DC 20.4 ... 28.8 V DC Reverse polarity protection Yes Yes 30 ... 55 mA 30 ... 45 mA 0.3 A per output 0.3 A per output 0.7 ... 1.3 W 0.8 ... 1.1 W Number 8 4 Electrical isolation No No Input voltage L+ L+ Signal g 0 Signal 1 < 5 V DC < 5 V DC > 8 V DC > 8 V DC Power supply Permissible mains frequency Power consumption from 24 V DC Voltage failure buffering Power loss at 24 V Backup of the real-time clock at 25 C Accuracy of the real-time clock Digital inputs 264 LOGO! Manual A5E00228550-01 Technical data LOGO! 24 LOGO! 24o LOGO! DM8 24 Signal 0 < 1.0 mA (I1...I6) < 0.05 mA (I7, ( , I8)) < 1.0 mA Signal 1 > 1.5 mA (I1... I6) > 0.1 mA (I7, I8) > 1.5 mA typ. 1.5 ms (I1...I4) typ. 1.5 ms Input current at Delay time at 0 to 1 <1.0 ms (I5, I6) typ. y 300 ms ((I7,I8)) 1 to 0 typ. 1.5 ms (I1...I4) typ. 1.5 ms <1.0 ms (I5, I6) typ. 300 ms (I7,I8) Line length (unshielded) 100 m 100 m Analog inputs Number 2 (I7 and I8) Range 0 ... 10 V DC input impedance 76 k max. input voltage 28.8 V DC Line length (shielded and twisted) 10 m Digital outputs Number 4 4 Output type Transistor, current-sourcing Transistor, current-sourcing Electrical isolation No No Control of a digital input Yes Yes Output voltage Supply voltage Supply voltage Output current max. 0.3 A max. 0.3 A In groups of LOGO! Manual A5E00228550-01 265 Technical data LOGO! 24 LOGO! 24o LOGO! DM8 24 Short circuit-proof and overload-proof Yes Yes Short-circuit current limitation Approx. 1 A Approx. 1 A Derating none; across the entire temperature range none; across the entire temperature range Not permitted Not permitted Electrical 10 Hz 10 Hz Ohmic load/lamp load 10 Hz 10 Hz Inductive load 0.5 Hz 0.5 Hz Continuous current Ith Incandescent lamp load (25000 switching cycles) at Fluorescent tubes with ballast (25000 switching cycles) Fluorescent tubes, conventionally compensated (25000 switching cycles) Fluorescent tubes, uncompensated (25000 switching cycles) Short circuit-proof cos 1 Short-circuit proof cos 0.5 to 0.7 Parallel output circuit for power increase Protection of output relay (if desired) Switching rate Mechanical 266 LOGO! Manual A5E00228550-01 Technical data A.4 Technical data: LOGO! 24RC... and LOGO! DM8 24 R LOGO! 24RC LOGO! 24RCo LOGO! DM8 24 R Input voltage 24 V AC/DC 24 V AC/DC Permissible range 20.4 ... 26.4 V AC 20.4 ... 28.8 V DC 20.4 ... 26.4 V AC 20.4 ... 28.8 V DC 47 ... 63 Hz 47 ... 63 Hz 24 V AC 24 V DC 40 ... 110 mA 40 ... 110 mA 20 ... 75 mA 20 ... 75 mA Voltage failure buffering typ. 5 ms typ. 5 ms 24 V AC 24 V DC 0.9 ... 2.7 W 0.9 ... 2.7 W 0.4 ... 1.8 W 0.4 ... 1.8 W Backup of the real-time clock at 25 C typ. 80 h typ. 80 h Accuracy of the real-time clock typ. 2 s / day Power supply Reverse polarity protection Permissible mains frequency Power consumption Power loss Digital inputs Number 8, optional P action or N action 4, optional P action or N action Electrical isolation No No Input voltage L L Signal g 0 Signal 1 < 5 V AC/DC < 5 V AC/DC > 12 V AC/DC > 12 V AC/DC LOGO! Manual A5E00228550-01 267 Technical data LOGO! 24RC LOGO! 24RCo LOGO! DM8 24 R < 1.0 mA < 1.0 mA > 2.5 mA > 2.5 mA 0 to 1 typ. 1,5 ms typ. 1.5 ms 1 to 0 typ. 15 ms typ. 15 ms Line length (unshielded) 100 m 100 m Number 4 4 Output type Relay outputs Relay outputs Electrical isolation Yes Yes In groups of 1 1 Control of a digital input Yes Yes Continuous current Ith max. 10 A per relay max. 5 A per relay Incandescent lamp load (25000 switching cycles) at 1000 W 1000 W Fluorescent tubes with ballast (25000 switching cycles) 10 x 58 W 10 x 58 W Input current at Signal 0 Signal 1 Delay time at Analog inputs Number Range max. Input voltage Digital outputs Output voltage Output current 268 LOGO! Manual A5E00228550-01 Technical data LOGO! 24RC LOGO! 24RCo LOGO! DM8 24 R Fluorescent tubes, conventionally compensated (25000 switching cycles) 1 x 58 W 1 x 58 W Fluorescent tubes, uncompensated (25000 switching cycles) 10 x 58 W 10 x 58 W Derating none; across the entire temperature range none; across the entire temperature range Short circuit-proof cos 1 Power protection B16, 600A Power protection B16, 600A Short-circuit proof cos 0.5 to 0.7 Power protection B16, 900A Power protection B16, 900A Parallel output circuits for power increase Not permitted Not permitted Protection of output relay (if desired) max. 16 A, characteristic B16 max. 16 A, characteristic B16 10 Hz 10 Hz Ohmic load/lamp load 2 Hz 2 Hz Inductive load 0.5 Hz 0.5 Hz Short circuit-proof and overload-proof Short-circuit current limitation Switching rate Mechanical Electrical LOGO! Manual A5E00228550-01 269 Technical data A.5 Technical data: LOGO! 12/24... and LOGO! DM8 12/24R LOGO! 12/24RC LOGO! 12/24RCo LOGO! DM8 12/24R Input voltage 12/24 V DC 12/24 V DC Permissible range 10.8 ... 28.8 V DC 10.8 ... 28.8 V DC Reverse polarity protection Yes Yes 30 ... 140 mA 30 ... 140 mA 20 ... 75 mA 20 ... 75 mA typ. 2 ms typ. 2 ms typ. 5 ms typ. 5 ms 12 V DC 24 V DC 0.3 ... 1.7 W 0.3 ... 1.7 W 0.4 ... 1.8 W 0.4 ... 1.8 W Backup of the real-time clock at 25 C typ. 80 h Accuracy of the real-time clock typ. 2 s / day Electrical isolation No No Number 8 4 Electrical isolation No No < 5 V DC < 5 V DC > 8 V DC > 8 V DC Power supply Power consumption 12 V DC 24 V DC Voltage failure buffering 12 V DC 24 V DC Power loss Digital inputs Input voltage L+ Signal g 0 Signal 1 270 LOGO! Manual A5E00228550-01 Technical data LOGO! 12/24RC LOGO! 12/24RCo LOGO! DM8 12/24R Signal 0 < 1.0 mA (I1...I6) < 0.05 mA (I7, I8) < 1.0 mA Signal Si l1 > 1.5 1 5 mA A (I1... (I1 I6) > 0.1 mA (I7, I8) > 1.5 mA typ. 1.5 ms typ. 1.5 ms Input current at Delay time at 0 to 1 <1.0 ms (I5, I6) typ. y 300 ms ((I7,I8)) 1 to 0 typ. 1.5 ms typ. 1.5 ms <1.0 ms (I5, I6) typ. 300 ms (I7,I8) Line length (unshielded) 100 m 100 m Analog inputs Number 2 (I7, I8) Range 0 ... 10 V DC input impedance 76 k max. Input voltage 28.8 V DC Line length (shielded and twisted) 10 m Digital outputs Number 4 4 Output type Relay outputs Relay outputs Electrical isolation Yes Yes In groups of 1 1 Control of a digital input Yes Yes Output voltage Output current LOGO! Manual A5E00228550-01 271 Technical data LOGO! 12/24RC LOGO! 12/24RCo LOGO! DM8 12/24R max. 10 A per relay max. 5 A per relay Incandescent lamp load (25000 switching cycles) at 1000 W 1000 W Fluorescent tubes with ballast (25000 switching cycles) 10 x 58 W 10 x 58 W Fluorescent tubes, conventionally compensated (25000 switching cycles) 1 x 58 W 1 x 58 W Fluorescent tubes, uncompensated (25000 switching cycles) 10 x 58 W 10 x 58 W Derating none; across the entire temperature range none; across the entire temperature range Short circuit-proof cos 1 Power protection B16 600A Power protection B16 600A Short-circuit proof cos 0.5 to 0.7 Power protection B16 900A Power protection B16 900A Parallel output circuits for power increase Not permitted Not permitted Protection of output relay (if desired) max. 16 A, characteristic B16 max. 16 A, characteristic B16 10 Hz 10 Hz Ohmic load/lamp load 2 Hz 2 Hz Inductive load 0.5 Hz 0.5 Hz Continuous current Ith (per terminal) Short circuit-proof and overload-proof Short-circuit current limitation Switching rate Mechanical Electrical 272 LOGO! Manual A5E00228550-01 Technical data A.6 Switching capacity and service life of the relay outputs Ohmic load Switching cycles/million 0.4 12/24 V AC/DC 115/120 V AC 230/240 V AC Maximum 10 A Maximum 10 A Maximum 10 A 0.3 120 V DC 240 V DC Maximum 0.2 A Maximum 0.1 A 0.5 0.2 0.1 2 4 6 8 10 Switched current/A Figure A Switching capacity and service life of the contacts with ohmic load (heating) Inductive load Switching cycles/million 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 1 12/24 V AC/DC 115/120 V AC 230/240 V AC Maximum 2 A Maximum 3 A Maximum 3 A 120 V DC 240 V DC Maximum 0.2 A Maximum 0.1 A 2 3 Switched current/A Figure B Switching capacity and service life of the contacts with high inductive load to IEC 947-5-1 DC 13/AC 15 (contactors, solenoid coils, motors) LOGO! Manual A5E00228550-01 273 Technical data A.7 Technical data: LOGO! AM 2 LOGO! AM 2 Power supply Input voltage 12/24 V DC Permissible range 10.8 ... 28.8 V DC Power consumption 25 ... 50 mA Voltage failure buffering typ. 5 ms Power loss at 12 V 24 V 0.3 ... 0.6 W Electrical isolation No Reverse polarity protection Yes Ground terminal for connecting ground and shielding of the analog measuring line. 0.6 ... 1.2 W Analog inputs Number 2 Type Unipolar Input range 0 ... 10 V DC (input impedance 76 k) or 0 ... 20 mA (input impedance <250 ) Resolution 10 bit, normalized to 0 ... 1000 Cycle time for analog value generation 50 ms Electrical isolation No Line length (shielded and twisted) 10 m Encoder supply voltage none Error limit +/- 1.5 % Interference frequency suppres- 55 Hz sion 274 LOGO! Manual A5E00228550-01 Technical data A.8 Technical data: LOGO! AM 2 PT100 LOGO! AM 2 PT100 Power supply Input voltage 12/24 V DC Permissible range 10.8 ... 28.8 V DC Power consumption 25 ... 50 mA Voltage failure buffering typ. 5 ms Power loss at 12 V 24 V 0.3 ... 0.6 W Electrical isolation No Reverse polarity protection Yes Ground terminal for connecting ground and shielding of the measuring line 0.6 ... 1.2 W Sensor inputs Number 2 Type Resistive thermocouple Pt100 Connection of sensors 2-wire technique 3-wire technique Yes Measurement range -50 C ... +200 C Yes -58 F ... +392 F Settings for the measurement display on the basic module: 1 C steps 0.25 C steps (rounded to one decimal) 1 C steps 0.25 C steps (rounded to one decimal) Offset: -200, Gain: 25 Offset: -200, Gain: 250 Offset: -128, Gain: 45 Offset: -128, Gain: 450 LOGO! Manual A5E00228550-01 275 Technical data LOGO! AM 2 PT100 Curve linearization No Measuring current Ic 1.1 mA Measurement rate depends on the installation typical: 50 ms Resolution 0.25 C Error limits of the final measured value: 0 C ... +200 C -50 C ... +200 C +/- 1.0 % Electrical isolation No Cable length (shielded) 10 m +/- 1.5 % Interference frequency suppres- 55 Hz sion 276 LOGO! Manual A5E00228550-01 Technical data A.9 Technical data: LOGO!Power 12 V LOGO! Power 12 V is a primary-switched power supply unit for LOGO! devices. Two current ranges are available. LOGO! Power 12 V / 1.9 A LOGO! Power 12 V / 4.5 A Input data Input voltage 120 ... 230 V AC Permissible range 85 ... 264 V AC Permissible mains frequency 47 ... 63 Hz Voltage failure buffering > 40 ms (at 187 V AC) Input current 0.3 ... 0.18 A 0.73 ... 0.43 A Make current (25C) 15 A 30 A Device protection Internal Recommended circuit breaker (IEC 898) in mains line > 6 A characteristic D > 10 A characteristic C Output data Output voltage 12 V DC Overall tolerance +/-3 % Adjustment range 11.1 ... 12.9 V DC Residual ripple < 200 mVpp Output current Overcurrent limiting 1.9 A 4.5 A 2.4 A 4.5 A Efficiency 80 % Parallel circuit for power increase Yes Electromagnetic compatibility Interference suppression EN 50081-1, EN 55022 Class B Interference immunity EN 50082-2 LOGO! Manual A5E00228550-01 277 Technical data LOGO! Power 12 V / 1.9 A LOGO! Power 12 V / 4.5 A Safety Electrical isolation, primary/ secondary Yes, SELV (to EN 60950/VDE 0805) Safety class II (to IEC 536/VDE 0106 T1) Protection mode IP 20 (to EN 60529/VDE 470 T1) CE marking Yes UL/CSA certification Yes; UL 508 / CSA 22.2 FM approval In preparation General details Ambient temperature range -20 ... +55C, natural convection Storage and shipping temperature -40 ... +70C Connections at input One terminal (1 x 2.5 mm2 or 2 x 1.5 mm2) per L1 and N Connections at output Two terminals (1x.2.5 mm2 or 2 x 1.5 mm2) per L+ and M Installation On 35 mm DIN rail, snap-on Dimensions in mm (WxHxD) 72 x 80 x 55 126 x 90 x 55 Approx. weight 0.2 kg 0.4 kg 278 LOGO! Manual A5E00228550-01 Technical data A.10 Technical data: LOGO!Power 24 V LOGO! Power 24 V is a primary-switched power supply module for LOGO! devices. Two current ranges are available. LOGO! Power 24 V / 1.3 A LOGO! Power 24 V / 2.5 A Input data Input voltage 120 ... 230 V AC Permissible range 85 ... 264 V AC Permissible mains frequency 47 ... 63 Hz Voltage failure buffering 40 ms (at 187 V AC) Input current 0.48 ... 0.3 A 0.85 ... 0.5 A Inrush current (25C) < 15 A < 30 A Device protection Internal Recommended circuit breaker (IEC 898) in mains line > 6 A characteristic D > 10 A characteristic C Output data Output voltage 24 V DC Overall tolerance +/- 3 % Adjustment range 22.2 ... 25.8 V DC Residual ripple < 250 mVpp Output current Overcurrent limiting 1.3 A 2.5 A 1.6 A 2.8 A Efficiency > 80 % Parallel circuit for power increase Yes Electromagnetic compatibility Interference suppression EN 50081-1, EN 55022 Class B Interference immunity EN 50082-2 LOGO! Manual A5E00228550-01 279 Technical data LOGO! Power 24 V / 1.3 A LOGO! Power 24 V / 2.5 A Safety Electrical isolation, primary/ secondary Yes, SELV (to EN 60950/VDE 0805) Safety class II (to IEC 536/VDE 0106 T1) Protection mode IP 20 (to EN 60529/VDE 470 T1) CE marking Yes UL/CSA certification Yes; UL 508 / CSA 22.2 FM approval Yes; Class I, Div. 2, T4 General details Ambient temperature range -20 ... +55C, natural convection Storage and shipping temperature -40 ... +70C Connections at input One terminal (1 x. 2.5 mm2 or 2 x 1.5 mm2) per L1 and N Connections at output Two terminals (1x.2.5 mm2 or 2 x 1.5 mm2) per L+ and M Installation On 35 mm DIN rail, snap-on Dimensions in mm (WxHxD) 72 x 80 x 55 126 x 90 x 55 Approx. weight 0.2 kg 0.4 kg 280 LOGO! Manual A5E00228550-01 Technical data A.11 Technical data: LOGO! Contact 24/230 LOGO! Contact 24 and LOGO! Contact 230 are switching modules for direct switching of ohmic loads up to 20 Amps and motors up to 4 kW (without noise emission, hum-free). Operating voltage LOGO! Contact 24 LOGO! Contact 230 24 V DC 230 V AC; 50/60 Hz Switching capacity Utilization category AC-1: Switching of ohmic loads at 55C Operating current at 400 V 20 A Output with three-phase loads at 400 V 13 kW Utilization category AC-2, AC-3: Motor with slip ring induction/cage armature Operating current at 400 V 8.4 A Output with three-phase loads at 400 V 4 kW Short-circuit protection: Assignment type 1 25 A Assignment type 2 10 A Connecting leads Fine-wire with wire end ferrules Solid wire 2 x (0.75 to 2.5) mm2 2 x (1 to 2.5) mm2 1 x 4 mm2 Dimensions (WxHxD) 36 x 72 x 55 Ambient temperature -25 ... +55C Storage temperature -50 ... +80C LOGO! Manual A5E00228550-01 281 Technical data 282 LOGO! Manual A5E00228550-01 B Determining the cycle time The program cycle is the complete execution of the circuit program, that is, primarily the reading in of the inputs, the processing of the circuit program and the subsequent reading out of the outputs. The cycle time is the time required to execute a circuit program once in full. The time required for a program cycle can be determined using a short test program. This test program is created in LOGO! and returns a value during its execution in parameter assignment mode from which the current cycle time is derived. Test program 1. Create the test program by linking an output to a threshold trigger and connecting the trigger input with an inverted flag. B1 M1 Qx Par Output Qx or other flag Mx B2 1 M1 M1 2. Configure the threshold trigger as shown below. A pulse is generated in each program cycle due to the inverted flag. The trigger interval is set to 2 seconds. LOGO! Manual A5E00228550-01 283 Determining the cycle B1 1+ On =1000 Off=0000 Press B1 2 G_T=02:00s 3. Now start the circuit program and switch LOGO! to parameter assignment mode. In this mode, view the trigger parameters. B1 On =1000 Off =0000 fa =0086 fa= total of measured pulses per timeba 4. The reciprocal value of fa is equivalent to the LOGO! execution time of the current circuit program in its memory. 1/fa = cycle time in s Explanation The inverted flag block changes its output signal at each program execution. Thus, one logic level (high or low) width is exactly equivalent to the length of one cycle. Hence, a period lasts 2 cycles. The threshold trigger indicates the ratio of periods per 2 seconds, which results in the ratio of cycles per second. Edge transition of the inverted flag at each circuit program execution Cycle time 1 period = 1 pulse = 2 cycles Period 284 LOGO! Manual A5E00228550-01 C LOGO! without display Because some specific applications do not require operator control and monitoring units such as buttons or a display, we provide the LOGO! 12/24RCo, LOGO! 24o, LOGO! 24RCo and LOGO! 230RCo versions without display. View of a LOGO! 230RCo, for example: L1 N I1 I2 I3 I4 I5 I6 I7 I8 RUN/STOP 1 Q1 2 1 Q2 2 1 Q3 2 1 Q4 2 Less is definitely more! The versions without display offer you the following benefits: Even more cost-effective without the operating element. Requires less switch cabinet space than conventional hardware. Substantial benefits with regard to flexibility and prime costs compared to stand-alone electronic switchgear. Of advantage even for applications in which merely two or three conventional switching devices can be replaced. Very easy to use. Access protected. Compatible to LOGO! versions with display. Offers the option to read data by means of LOGO!Soft Comfort. LOGO! Manual A5E00228550-01 285 LOGO! without display Creating a circuit program without operator panel There are two ways to create a circuit program for a LOGO! without display: You create the circuit program with LOGO!Soft Comfort on your PC and then download it to the LOGO! (see Chapter 7). You download the circuit program from a LOGO! program module (card) to your LOGO! without display (see Chapter 6). Operating characteristics LOGO! is ready for operation when power is switched on. Switching off a LOGO! without display is equivalent to disconnecting the power supply, e.g. as if you were removing the plug. The circuit program of LOGO!...o versions can not be started or stopped by means of buttons. This is why the LOGO!...o versions have other startup characteristics: Startup characteristics If there is no circuit program in the LOGO! or on the inserted program module (card), LOGO! remains in STOP. If there is a valid circuit program in LOGO! memory, the LOGO! automatically switches from STOP to RUN when power is switched on. The circuit program on an inserted program module (card) is automatically copied to the LOGO!, immediately after power is switched on. The existing circuit program in LOGO! memory is overwritten. The system automatically changes from STOP to RUN. Provided the PC cable is connected to the LOGO!, you can download the circuit program to LOGO! and start it by means of the LOGO!Soft Comfort PC software (see Chapter 7.1). 286 LOGO! Manual A5E00228550-01 LOGO! without display Operating status indication Operating states, e.g. Power On, RUN and STOP are indicated by an LED on the front hood. Red LED: Power On/STOP Green LED: Power On/RUN The red LED is lit after Power On and in all LOGO! states other than RUN. The green LED is lit when LOGO! is in RUN mode. Reading current data LOGO!Soft Comfort (see Chapter 7) provides an online test for reading the current data of all functions while the system is in RUN. If your LOGO! without display holds a protected program module (card), you can not read the current data unless you enter the correct password for your the circuit program. The circuit program is otherwise deleted from LOGO! memory when you remove the program module (card) to connect the PC cable, for example (see Chapter 6.1). LOGO! Manual A5E00228550-01 287 LOGO! without display 288 LOGO! Manual A5E00228550-01 D LOGO! menu structure Menu overview No Program >Program.. Card.. Clock.. Start No Program Press ESC Circuit program is busy (RUN) Mo 09:00 2003-01-27 See "Start menu" See "Main menu" >Stop Set Param Set Clock Prg Name Parameter assignment menu >Yes Parameter setting (Chapter 5.1.1 cont.) Clock/date setting (Chapter 5.2) Display of the program name Main menu (ESC / >Stop) >Stop/>Yes >Program Card Clock Start See "Programming menu" >Edit.. > ->Card See "Transfer menu" >Set See "Clock menu" Clock See "Start menu" Mo 09:00 2003-01-27 Programming menu (ESC / >Stop >Edit.. Editing the program (Chapter 3.6 cont.) >Edit Prg Password? >Edit Name Editing the program name (Chapter 3.6.4) >Memory? Show available memory space (Chapter 3.7) >Clear Prg Deleting the program (Chapter 3.6.11) >Password Input/change of password (Chapter 3.6.5) LOGO! Manual A5E00228550-01 >Program) 289 LOGO! Menu structure Transfer menu (ESC / >Stop > >Card) Copying the circuit program from LOGO! to the program module (card) (Chapter 6.3) ->Card >Card-> Copying the program from the program module (card) to LOGO! (Chapter 6.4) >CopyProtect Setting the program/copy protection (Chapter 6.1) Clock menu (ESC / >Stop >Clock) >Set Clock Setting the time/date (Chapter 5.2) >S/W Time Setting the summertime/wintertime (Chapter 3.6.12) >Sync Synchronizing the times of LOGO! Basic and expansion modules (Chapter 3.6.13) Start menu (RUN) Everything clear? LOGO! Mo 09:00 2003-01-27 max. 10 message texts I: Q: M: 0.. 123456789 0.. 123456789 0.. 123456789 1..0123456789 1..0123456 1..0123456789 2..01234 Date/time Inputs ESC+Key 2..01234 Outputs Flags Cursor keys >Stop Set Param Set Clock Prg Name Parameter assignment menu 290 LOGO! Manual A5E00228550-01 E Order numbers Table A Variant Basic Basic without display (pure) Digital modules Analog modules Designation Order number LOGO! 12/24 RC * 6ED1052-1MD00-0BA4 LOGO! 24): 6ED1052-1CC00-0BA4 LOGO! 24 RC (AC) 6ED1052-1HB00-0BA4 LOGO! 230 RC 6ED1052-1FB00-0BA4 LOGO! 12/24 RCo * 6ED1052-2MD00-0BA4 LOGO! 24o * 6ED1052-2CC00-0BA4 LOGO! 24 RCo (AC) 6ED1052-2HB00-0BA4 LOGO! 230 RCo 6ED1052-2FB00-0BA4 LOGO! DM 8 12/24R 6ED1055-1MB00-0BA1 LOGO! DM 8 24 6ED1055-1CB00-0BA0 LOGO! DM 8 24R 6ED1055-1HB00-0BA0 LOGO! DM 8 230R 6ED1055-1FB00-0BA1 LOGO! AM 2 6ED1055-1MA00-0BA0 LOGO! AM 2 PT100 6ED1055-1MD00-0BA0 *: Also with analog inputs LOGO! Manual A5E00228550-01 291 Order numbers Table B Accessories Software Designation Order number LOGO!Soft Comfort V4.0 6ED1058-0BA00-0YA0 Upgrade to LOGO!Soft Comfort V4.0 6ED1058-0CA00-0YE0 Program module (card) LOGO! Card 6ED1056-5CA00-0BA0 Switching modules LOGO!Contact 24 V 6ED1057-4CA00-0AA0 LOGO!Contact 230 V 6ED1057-4EA00-0AA0 Power modules LOGO!Power 12V/1.9A 6EP1321-1SH01 LOGO!Power 12V/4.5A 6EP1322-1SH01 LOGO!Power 24V/1.3A 6EP1331-1SH01 LOGO!Power 24V/2.5A 6EP1332-1SH41 PC cable 6ED1057-1AA00-0BA0 Manual 6ED1050-1AA00-0BE5 Others 292 LOGO! Manual A5E00228550-01 F Abbreviations AM B1 BN C CM Cnt Co Dir DM En Analog module Block number B1 Block Number LOGO! device designation: integrated clock Communication Module Count = Counter input Connector Direction (of count, for example) Digital Module Enable = switching on (clock generators, for example) Fre Input for frequency signals to be analyzed GF Basic Functions Inv Input for inverting the output signal No Cam (parameter of the timer) o in LOGO! designations: without display Par Parameter R Reset input R in LOGO! designations: Relay outputs Ral Reset all = Input for resetting all internal values S Set (latching relay, for example) SF Special functions SU Subunit T Time = parameter Trg Trigger (parameter) 0BA4 devices: the latest LOGO! Basic version, described in this Manual. LOGO! Manual A5E00228550-01 293 Order numbers 294 LOGO! Manual A5E00228550-01 Index A Abbreviations, 293 AM. See Analog module Amplifier, analog, 173 Analog comparator, 165 values, 106 Analog amplifier, 173 Analog differential trigger, 161 Analog module, 2, 7 Analog threshold trigger, 158 BF, 89 Blank outputs, 40 blank outputs, 91 Block, 42 deleting, 74 block groups, 75 inserting, 69 number, 42 assigning, 43 BN, 89 C Analog value monitoring, 170 Cap, 17 AND, 95 Card. See Program module (card) Applications, 221 AS interface, 2, 243 CE label, 10 Asynchronous pulse generator, 128 Character set, 60 Certification, 9 Circuit diagram, 45 B Basic functions, 93 AND, 95 with edge, 96 NAND, 97 with edge, 98 NOR, 100 NOT, 101 OR, 99 XOR, 101 Basics on special functions, 102 LOGO! Manual A5E00228550-01 Circuit program, input, 54 circuit program, 84 deleting, 77 Circuit program name, assigning, 60 Circuit programs archiving, 203 reproduce, 203 send by mail, 203 Closing the programming mode, 74 295 Index CM. See Communications mo dule Co, 89, 90 Communication module, AS in terface, 243 Communications module, 2 AS interface, 2, 7 Compatibility, Versions, 204 Connecting Inputs, 25 outputs, 31 Cursor movement, 49 Cycle time, 283 D Demo versions, 217 Device types, LOGO!, 2 Digital module, 2, 7 Dimensions, 16 DIN rail, 16 Connector, 17 Display, 43 Connectors, 39, 90 blank, 40 hi, 41 inputs, 41 lo, 41 LOGO!'s, 40 open, 92 outputs, 41 unused, 46 x, 40, 41, 46, 103 Display view, 43 Constants, 90 Control panel, 4, 5 Conversion, Summertime and wintertime, 78 Correcting typing errors, 76 Counter Operating hours, 150 Up/down, 146 CSA, 9 cULus , 9 Cursor, 49 Cursor keys, 40, 92, 184 296 Disposal, 10 DM. See Digital module E Earth connection, 24 Edge evaluation, 96, 98 Editing, 69 Example Air-conditioning system, 234 Automatic door, 227 Factory door, 239 factory door controlling, 243 Monitoring, 243 further options, 255 lighting corridor, 223 stairway, 223 Luminous rows, 247 Service water pump, 251 LOGO! Manual A5E00228550-01 Index exclusive OR, 101 Expansion modules, 2 Analog module, 2, 41 Communications module, 2 Digital module, 41 digital module, 2 Operating state, 36 expansion modules, 39 F Flag blocks, 91 FM, 9 Four golden rules, 48 Function blocks, 42 Functions, 89 G Gain, 106 GF, 93 Golden rules, 48 Guidelines, 11 H Hiding, 72 I Inputs, 90 Analog inputs, 27, 90 connection, 25 Cursor keys, 40, 92 Digital Inputs, 90 Groups, 25 inverting, 59, 93, 109 unused, 46 inputs, High-speed inputs, 27 Inserting, 69 Installation guidelines, 11 Interlock, 18, 20 Interpulse, width, 129 Inverter, 101 L Latching relay, 175 LCD, 4, 5 LED, 287 Levels, 92 List BF, 89 BN, 89 Co, 89, 90 SF, 89, 109 high-speed counting, 27 List , GF, 93 Hours counter, 150 Reading the MN and OT va lues, 153 Logical inputs, 103 Hysteresis, 169 LOGO! Manual A5E00228550-01 Logic module, 1 LOGO! connecting to PC, 218 297 Index Guidelines, 11 identifying, 7 Installing, 16 Operating states, 36 removing, 16 Structure of, 4 switching on, 33 Versions, 8 wiring, 23 Mounting DIN rail mounting, 17 Drilling template, 22 Wall-mounting, 21 Multiple function switch, 135 N LOGO! menus, 50 Name, 60 LOGO! software, 215 NAND, 97 LOGO!Soft Comfort, 216 Negation, 101 of a BF input, 93 of an input, 59 of an SF input, 109 M Memory areas, 84 free, 88 limitation, 84 requirements, 85 space, 84 Menu structure, 289 Menus Main menu, 50 Parameter assignment menu, 50 Programming menu, 50 Real-time clock menu, 50 Transfer menu, 50 Message texts, 179 Character set, 184 Mode Parameter assignment, 194 parameter assignment, 50 PC-LOGO, 218 programming, 50 298 NOR , 100 NOT , 101 NOT AND, 97 NOT OR, 100 O Off-delay, 117 Off-time, 140 Offset, 106 On-/Off-delay, 119 On-delay, 113 retentive, 121 On-time, 140 Open connectors, 92 Operating characteristics, 286 LOGO! Manual A5E00228550-01 Index Status indication, 287 Operating mode Changing the operating mode, 48 Programming mode, 51 OR, 99 Order numbers, 291 Outputs, 90 Analog outputs, 91 blank, 40, 91 connecting, 31 Digital outputs, 90 P Parameter, 196 'Set Param', 195 Inputs, 104 selecting, 197 setting, 193 T, 104 Parameter assignment, 71 Parameter assignment menu, 194 Parameter assignment screen form, 139, 181 Parameter protection, 106 Parameters, modifying, 198 parameters, showing/hiding, 72 Password assigning, 61 changing, 63 deactivating, 64 wrong, 65 PC cable, 218 USB, 218 LOGO! Manual A5E00228550-01 PC-LOGO, 218 Planning, 49 Power off, 34 On, 33 on, 34 switch, 33 Power supply, connecting, 23 Program memory, 84 Program chart, 44 Program cycle, 283 Program module (card) 'Card --> LOGO', 213 'CopyProtect', 206 'LOGO --> Card', 210 copying, 212 Enabling the security function, 207 inserting, 208, 209 removing, 208, 209 Security function, 205 Program name change, 61 character set, 60 read, 195 Programs 'Clear Prg', 77 'Edit Name', 60 'Edit Prg', 52 'Password', 61 modifying, 68 Protection mode, 72 Pulse Pause, 126 width, 126 width , 129 299 Index pulse generator, Asynchronous , 128 Pulse output, 123 Pulse relay, 176 R Setup, 13 Maximum setup, 13 with different voltage classes, 14 SF, 89, 109 SFs, Delay, On, 113 Shift register, 190 Random generator, 130 Shift register bits, 40, 92 Recycling, 10 Showing, 72 Relay outputs, 31, 273 service life, 273 switching capacity, 273 Signal status transitions, 27 Removal, 19 Resources, 84 Retentive memory, 84 Retentive on-delay, 121 Retentivity, 105 enabling/disabling, Retentivity setting, 72 Rules, Four golden, 48 RUN, 'Start', 66 S Sensor Characteristics, 25 Sensor connections, 28 Set clock, 'Set Clock', 201 Setting, time, 72 Setting the date, 201 Setting the time-of-day, 201 'Set clock', 195 300 Simulation, 215 Size of a circuit, 84 Softkey, 186 Software, 215 Solid-state outputs, 32 Special functions, 109 Analog amplifier, 173 Analog Comparator, 165 Analog differential trigger, 161 Analog threshold trigger, 158 Analog value monitoring, 170 Basics, 102 Counter Hours counter, 150 Up/down, 146 Delay Off, 117 On/Off, 119 delay, ret. on, 121 Message texts, 179 Pulse generator, asynchronous, 128 Random generator, 130 Relay, Latch, 175 LOGO! Manual A5E00228550-01 Index relay, Pulse, 176 Shift register, 190 Softkey, 186 Switch Comfort, 135 Stairway lighting, 132 Threshold trigger, Frequency, 155 Timer Week, 138 Year, 143 Trigger, Analog threshold, 158 Wiping relay edge triggered, 125 Pulse output, 123 Stairway lighting switch, 132 Start, 66 Startup characteristics, 286 Startup flag, 92 Stop, 195 Subunits, 16 Summertime, 78 Summertime/Wintertime Con version, 'S/W Time', 78 enabling, 83 T T, Parameter, 105 Technical data, 259 general, 259 LOGO! 12..., 270 LOGO! 230...., 261 LOGO! 24/24o, 264 LOGO! 24RC/24RCo, 267 LOGO! AM 2 PT100, 275 LOGO! AM2, 274 LOGO! DM8 12/24R, 270 LOGO! DM8 230R, 261 LOGO! DM8 24, 264 LOGO! DM8 24R, 267 LOGO!Contact, 281 LOGO!Power 12 V, 277 Threshold trigger, Frequencies, 155 Time, Accuracy of, 104 Time response, 104 Timebase, 71, 104, 113 Summertime/wintertime conver sion, 78 disabling, 82 enabling, 79 user-define parameters, 81 Timer, 1 accuracy, 105 Switch Multiple function, 135 Stairway lighting, 132 trigger, Analog, Differential, 161 Timing inaccuracy , 105 Trigger, Analog threshold, 158 type of equipment, LOGO!, 2 Switched current, maximum, 32 Symbols, 7 Synchronization, 83 'Sync', 83 LOGO! Manual A5E00228550-01 301 Index U Unused connectors, 46 unused connectors, 40 Unused inputs, 46 Up/down counter, 146 Update, 217 Upward compatibility, 204 USB, 218 V Verification, 73 Voltage levels , 92 Voltage supply, connecting, Cir cuit protection, 24 W Weekday, 139 Weekly timer, 7, 140 Examples, 141 302 setting, 140 Weekly timer , 138 Wintertime, 78 Wiping relay edge triggered, 125 Pulse output, 123 Wire ferrules, 23 without display, 285 creating a circuit program, 37 PC-LOGO mode, 218 reading current data, 287 X XOR , 101 Y Yearly timer, 143 Z Zero offset, 106 LOGO! Manual A5E00228550-01 Produktinformation 07.2004 Produktinformation zum Handbuch LOGO!; ab Ausgabe 06/2003 (A5E00228104-01) Vorbemerkung Diese Produktinformation enthalt wichtige Informationen zu LOGO! Sie ist als separater Bestandteil aufzufassen und in Zweifelsfallen in der Verbindlichkeit anderen Aussagen in Handbuchern und Katalogen ubergeordnet. Diese Produktinformation enthalt die Erganzungen fur die LOGO!-Erweiterungsmodule DM16 24, DM16 24R und DM16 230R. Copyright 2004 by Siemens AG A5E00324307-01 1.1 Welche Erweiterungsmodule gibt es? * LOGO! Digitalmodule DM8... gibt es fur 12 V DC, 24 V AC/DC und 115...240 V AC/DC mit 4 Eingangen und 4 Ausgangen. * LOGO! Digitalmodule DM16... gibt es fur 24 V DC und 115...240 V AC/DC mit 8 Eingangen und 8 Ausgangen. * LOGO! Analogmodule gibt es fur 12 V DC und 24 V DC mit 2 Analogeingangen bzw. mit 2 Pt100-Eingangen. * LOGO! Kommunikationsmodule (CM), wie z.B. Kommunikationsmodul AS-Interface, das in einer eigenen Dokumentation beschrieben wird. Digital- und Analogmodule sind in 2 bzw. 4 TE integriert und besitzen jeweils zwei Erweiterungsschnittstellen, so dass an jedes ein weiteres Modul angeschlossen sein kann. So ist LOGO! aufgebaut 2 7 7 8 6 L+ M I1 I2 I3 I4 I5 I6 I7 I8 4 5 4 RUN/STOP 1 1 Q1 Q5 2 1 2 1 Q2 Q6 2 1 2 Q3 1 2 1 Q7 Q2 Q4 2 1 90 6 1 35 LOGO! Erweiterungsmodul (z.B.: DM16 24R) 1.2 2 Q8 2 3 72 1 Spannungsversorgung 2 Eingange 3 Ausgange 53 4 Anzeige des Zustandes RUN/STOP 7 Mechanische Codierung - Stifte 5 Schieber 8 6 Erweiterungsschnittstelle Mechanische Codierung - Buchsen Symbole Digitalmodul verfugt uber 4 Digitaleingange und 4 Digitalausgange Digitalmodul verfugt uber 8 Digitaleingange und 8 Digitalausgange 2 Produktinformation LOGO! A5E00324307-01 1.3 Erweiterungsmodule An LOGO! konnen folgende Erweiterungsmodule angeschlossen werden: Symbol Bezeichnung Versorgung Eingange Ausgange LOGO! DM 8 12/24R 12/24 V DC 4 Digital 4 Relais je 5A LOGO! DM 8 24 24 V DC 4 Digital 4 Transistor 24V / 0,3A LOGO! DM 8 24R (3) 24 V AC/DC 4 Digital 4 Relais je 5A LOGO! DM 8 230R 115...240 V AC/DC 4 Digital (1) 4 Relais je 5A LOGO! DM 16 24 24 V DC 8 Digital 8 Transistor 24V / 0,3A LOGO! DM 16 24R 24 V DC 8 Digital 8 Relais je 5A LOGO! DM 16 230R 115...240 V AC/DC 8 Digital (4) 8 Relais je 5A LOGO! AM 2 12/24 V DC 2 Analog 0 ... 10V oder 0 ... 20mA (2) keine LOGO! AM 2 PT100 12/24 V DC 2 Pt100 -50 C bis +200 C keine (1): Keine unterschiedlichen Phasen innerhalb der Eingange erlaubt. (2): 0 ... 10V, 0 ... 20 mA sind wahlweise anschliebar. (3): Digitaleingange konnen wahlweise P-schaltend oder N-schaltend betrieben werden. (4): Eingange in zwei Gruppen von 4. Innerhalb der Gruppe nur eine gleiche Phase, zwischen den Gruppen verschiedene Phasen moglich. 1.4 Aufbau mit unterschiedlichen Spannungsklassen Regeln Digitalmodule konnen Sie nur an Gerate der gleichen Spannungsklasse anschlieen. Analogmodule und Kommunikationsmodule konnen Sie an Gerate mit beliebiger Spannungsklasse anschlieen. Sie konnen ohne eine Anderung des Schaltprogramms zwei gleiche DM8-Erweiterungsmodule durch ein gleichartiges DM16-Erweiterungsmodul ersetzen (und umgekehrt). Achtung Zwei DM8 12/24R konnen nur bei einer Versorgungsspannung von 24 V DC gegen ein DM16 24R getauscht werden. Zwei DM8 24R konnen nur in der Betriebsart DC, P-schaltend gegen ein DM16 24R getauscht werden. Produktinformation LOGO! A5E00324307-01 3 Ubersicht: Erweiterungsmodul an LOGO! Basic anschlieen LOGO! B i Basic Erweiterungsmodule DM8 12/24R, DM16 24R DM8 24, DM16 24 DM8 24R DM8 230R, DM16 230R AM2, AM2 PT100 CM LOGO! 12/24RC x x x - x x LOGO! 24 x x x - x x LOGO! 24RC x x x - x x LOGO! 230RC - - - x x x LOGO! 12/24RCo x x x - x x LOGO! 24o x x x - x x LOGO! 24RCo x x x - x x LOGO! 230RCo - - - x x x Ubersicht: Erweiterungsmodul an Erweiterungsmodul anschlieen Erweiterungsmodul d l Weitere Erweiterungsmodule DM8 12/24R, DM16 24R DM8 24, DM16 24 DM 8 24R DM8 230R, DM16 230R AM2, AM2 PT100 CM DM 8 12/24R, DM 16 24R x x x - x x DM 8 24, DM 16 24 x x x - x x DM 8 24R x x x - x x DM 8 230R, DM 16 230R - - - x x x AM2 / AM2 PT100 x x x - x x CM x x x - x x 4 Produktinformation LOGO! A5E00324307-01 1.5 Abmessungen LOGO! besitzt die Abmessungen fur Installationsgerate gema DIN 43880. LOGO! kann auf eine 35 mm breite Hutschiene nach DIN EN 50022 aufgeschnappt oder an die Wand montiert werden. Breite von LOGO!: * LOGO! Basic ist 72 mm breit, das entspricht 4 Teilungseinheiten. * LOGO! Erweiterungsmodule sind 36 mm bzw. 72 mm (DM16...) breit, das entspricht 2 bzw. 4 Teilungseinheiten. 1.6 Eingange von LOGO! anschlieen Sensoreigenschaften fur LOGO! LOGO! DM16 24 R LOGO! DM16 24 LOGO! DM16 230 R (AC) LOGO! DM16 230 R (DC) Schaltzustand 0 < 5 V DC < 5 V DC < 40 V AC < 30 V DC Eingangsstrom < 1 mA < 1 mA < 0,05 mA < 0,05 mA Schaltzustand 1 > 12 V DC > 12 V DC > 79 V AC > 79 V DC Eingangsstrom > 2 mA > 2 mA > 0,08 mA > 0,08 mA Achtung Die Digitaleingange der LOGO! 230 RC/RCo und des Erweiterungsmoduls DM16 230R sind in zwei Gruppen aufgeteilt, die jeweils uber 4 Eingange verfugen. Innerhalb einer Gruppe muss an allen Eingangen die gleiche Phase verwendet werden. Verschiedene Phasen sind nur zwischen den Gruppen moglich. Beispiel: I1 bis I4 an Phase L1, I5 bis I8 an Phase L2. Bei LOGO! DM8 230R durfen innerhalb der Eingange keine unterschiedlichen Phasen angeschlossen werden. Sensoranschlusse Anschlieen von Glimmlampen, 2-Draht-Naherungsschalter (Bero) an LOGO! 230RC/230RCo oder LOGO! DM8 230R (AC) und LOGO! DM16 230R (AC) L1 N Bestellbezeichnung fur C: Siemens Schaltgerate & Systeme C L1 3SB1420-3D N X-Kondensator 2,5 kV, 100 nF Produktinformation LOGO! A5E00324307-01 5 1.7 Technische Daten Allgemeine Technische Daten Kriterium Prufung nach Werte LOGO!Basic Abmessungen BxHxT 72 x 90 x 55 mm Gewicht ca. 190 g Montage auf Hutschiene 35 mm 4 Teilungseinheiten breit oder Wandmontage LOGO! Erweiterungsmodule DM8..., AM... Abmessungen BxHxT 36 x 90 x 53 mm Gewicht ca. 90 g Montage auf Hutschiene 35 mm 2 Teilungseinheiten breit oder Wandmontage LOGO! Erweiterungsmodule DM16... Abmessungen BxHxT 72 x 90 x 53 mm Gewicht ca. 190 g Montage auf Hutschiene 35 mm 4 Teilungseinheiten breit oder Wandmontage Klimatische Umgebungsbedingungen Umgebungstemperatur waagrechter Einbau senkrechter Einbau Kalte nach IEC 60068-2-1 Warme nach IEC 60068-2-2 IEC 60068-2-30 Luftdruck Schadstoffe 0 ... 55 C -40 C ... +70 C Lagerung / Transport Relative Feuchte 0 ... 55 C C von 10 bis 95% keine Betauung 795 ... 1080 hPa IEC 60068-2-42 SO2 10 cm3 /m3, 4 Tage IEC 60068-2-43 H2S 1 cm3 /m3, 4 Tage Mechanische Umgebungsbedingungen Schutzart Schwingungen IP 20 IEC 60068-2-6 5 ... 9 Hz (konstante Amplitude 3,5 mm) 9 ... 150 Hz (konstante Beschleunigung 1 g) Schock IEC 60068-2-27 18 Schocks (Halbsinus 15g/11ms) Kippfallen IEC 60068-2-31 Fallhohe 50 mm Freier Fall, verpackt IEC 60068-2-32 1m 6 Produktinformation LOGO! A5E00324307-01 Kriterium Prufung nach Werte Elektromagnetische Vertraglichkeit (EMV) Storaussendung EN 55011/A EN 55022/B Grenzwertklasse B Gruppe 1 EN 50081-1 (Wohnbereich) Elektrostatische Entladung IEC 61000-4-2 8 kV Luftentladung Scharfegrad 3 6 kV Kontaktentladung Elektromagnetische Felder IEC 61000-4-3 Feldstarke 10 V/m HF-Bestromung auf Leitungen und Leitungsschirmen IEC 61000-4-6 10 V Burst Impulse IEC 61000-4-4 2 kV (Versorgungs- und Signalleitungen) Scharfegrad 3 Energiereicher Einzelimpuls (Surge) IEC 61000-4-5 Scharfegrad 3 (nur bei LOGO! 230....) 1 kV (Versorgungsleitungen) symmetrisch 2 kV (Versorgungsleitungen) asymmetrisch Angaben uber IEC- / VDE-Sicherheit Bemessung der Luft- u. Kriechstrecken IEC 60664, IEC 61131-2, EN 50178 cULus nach UL 508, CSA C22.2 No. 142 Bei LOGO! 230R/RC auch VDE 0631 erfullt Isolationsfestigkeit IEC 61131-2 erfullt Produktinformation LOGO! A5E00324307-01 7 Technische Daten: LOGO! DM16 230R LOGO! DM16 230R Stromversorgung Eingangsspannung 115 ... 240 V AC/DC Zulassiger Bereich 85 ... 265 V AC 100 ... 253 V DC Zulassige Netzfrequenz: 47 ... 63 Hz Stromaufnahme * * * * 115 V AC 10 ... 60 mA 240 V AC 10 ... 40 mA 115 V DC 5 ... 25 mA 240 V DC 5 ... 20 mA Spannnungsausfalluberbruckung * 115 V AC/DC * 240 V AC/DC typ typ. yp 10 ms typ. typ 20 ms Verlustleistung bei * * * * 115 V AC 1,1 , ... 4,5 , W 240 V AC 2,4 , ... 5,5 , W 115 V DC 0,6 ... 2,9 W 240 V DC 1,2 ... 4,8 W Pufferung der Uhr bei 25 _C Ganggenauigkeit der Echtzeituhr Digitaleingange Anzahl 8 Potentialtrennung nein Eingangsspannung L1 * * * * Signal 0 < 40 V AC Signal 1 > 79 V AC Signal 0 < 30 V DC Signal 1 > 79 V DC Eingangsstrom bei * Signal g 0 * Signal 1 < 0,05 mA > 0,08 mA Verzogerungszeit bei * 0 nach 1 * 1 nach 0 typ. yp 50 ms Leitungslange (ungeschirmt) 100 m typ. 50 ms Digitalausgange Anzahl 8 Typ der Ausgange Relaisausgange Potentialtrennung ja in Gruppen zu 1 Ansteuerung eines Digitaleingangs ja 8 Produktinformation LOGO! A5E00324307-01 LOGO! DM16 230R Dauerstrom Ith max. 5 A je Relais Gluhlampenlast (25.000 Schaltspiele) bei 230/240 V AC 1000 W 115/120 V AC 500 W Leuchtstoffrohren mit elektr. Vorschaltgerat (25.000 Schaltspiele) 10 x 58 W (bei 230/240 V AC) Leuchtstoffrohren konventionell kompensiert (25.000 Schaltspiele) 1 x 58 W (bei 230/240 V AC) Leuchtstoffrohren unkompensiert (25.000 Schaltspiele) 10 x 58 W (bei 230/240 V AC) Kurzschlussfest cos 1 Leistungsschutz B16 600A Kurzschlussfest cos 0.5 bis 0.7 Leistungsschutz B16 900A Derating kein; im gesamten Temperaturbereich Parallelschaltung von Ausgangen zur Leistungserhohung nicht zulassig Absicherung eines Ausgangsrelais (falls gewunscht) max. 16 A, Charakteristik B16 Schaltfrequenz mechanisch 10 Hz Ohmsche Last/Lampenlast 2 Hz Induktive Last 0,5 Hz Produktinformation LOGO! A5E00324307-01 9 Technische Daten: LOGO! DM16 24 LOGO! DM16 24 Stromversorgung Eingangsspannung 24 V DC Zulassiger Bereich 20,4 ... 28,8 V DC Verpolschutz ja Zulassige Netzfrequenz Stromaufnahme aus 24 V 30 ... 45 mA 0,3 A je Ausgang Spannnungsausfalluberbruckung Verlustleistung bei 24 V 0,8 ... 1,7 W Pufferung der Uhr bei 25 _C Ganggenauigkeit der Echtzeituhr Digitaleingange Anzahl 8 Potentialtrennung nein Eingangsspannung L+ * Signal g 0 * Signal 1 < 5 V DC > 12 V DC Eingangsstrom bei * Signal g 0 * Signal 1 < 1 mA > 2 mA Verzogerungszeit bei * 0 nach 1 * 1 nach 0 typ. yp 1,5 ms Leitungslange (ungeschirmt) 100 m typ. 1,5 ms Digitalausgange Anzahl 8 Typ der Ausgange Transistor, P-schaltend Potentialtrennung nein in Gruppen zu Ansteuerung eines Digitaleingangs ja Ausgangsspannung Versorgungsspannung Ausgangsstrom max. 0,3 A Dauerstrom Ith Gluhlampenlast (25.000 Schaltspiele) bei Leuchtstoffrohren mit elektr. Vorschaltgerat (25.000 Schaltspiele) Leuchtstoffrohren konventionell kompensiert (25.000 Schaltspiele) Leuchtstoffrohren unkompensiert (25.000 Schaltspiele) 10 Produktinformation LOGO! A5E00324307-01 LOGO! DM16 24 Kurzschlussfest und uberlastsicher ja Kurzschlussstrombegrenzung ca. 1 A Derating kein; im gesamten Temperaturbereich Kurzschlussfest cos 1 Kurzschlussfest cos 0.5 bis 0.7 Parallelschaltung von Ausgangen zur Leistungserhohung nicht zulassig Absicherung eines Ausgangsrelais (falls gewunscht) Schaltfrequenz mechanisch elektrisch 10 Hz Ohmsche Last/Lampenlast 10 Hz Induktive Last 0,5 Hz Produktinformation LOGO! A5E00324307-01 11 Technische Daten: LOGO! DM16 24R LOGO! DM16 24R Stromversorgung Eingangsspannung 24 V DC Zulassiger Bereich 20,4 ... 28,8 V DC Verpolschutz ja Stromaufnahme * 24 V DC 30 ... 90 mA Spannnungsausfalluberbruckung * 24 V DC typ. 5 ms Verlustleistung * 24 V DC 0,7 ... 2,5 W Pufferung der Uhr bei 25 _C Ganggenauigkeit der Echtzeituhr Potentialtrennung nein Digitaleingange Anzahl 8 Potentialtrennung nein Eingangsspannung L+ * Signal g 0 * Signal 1 < 5 V DC > 12 V DC Eingangsstrom bei * Signal g 0 * Signal 1 < 1 mA > 2 mA Verzogerungszeit bei * 0 nach 1 * 1 nach 0 typ. yp 1,5 ms Leitungslange (ungeschirmt) 100 m typ. 1,5 ms Digitalausgange Anzahl 8 Typ der Ausgange Relaisausgange Potentialtrennung ja in Gruppen zu 1 Ansteuerung eines Digitaleingangs ja Ausgangsspannung Ausgangsstrom Dauerstrom Ith (je Klemme) max. 5 A je Relais Gluhlampenlast (25.000 Schaltspiele) 1000 W Leuchtstoffrohren mit elektr. Vorschaltgerat (25.000 Schaltspiele) 10 x 58 W Leuchtstoffrohren konventionell kompensiert (25.000 Schaltspiele) 1 x 58 W 12 Produktinformation LOGO! A5E00324307-01 LOGO! DM16 24R Leuchtstoffrohren unkompensiert (25.000 Schaltspiele) 10 x 58 W Kurzschlussfest und uberlastsicher Kurzschlussstrombegrenzung Derating kein; im gesamten Temperaturbereich Kurzschlussfest cos 1 Leistungsschutz B16 600A Kurzschlussfest cos 0.5 bis 0.7 Leistungsschutz B16 900A Parallelschaltung von Ausgangen zur Leistungserhohung nicht zulassig Absicherung eines Ausgangsrelais (falls gewunscht) max. 16 A, Charakteristik B16 Schaltfrequenz mechanisch 10 Hz elektrisch Ohmsche Last/Lampenlast 2 Hz Induktive Last 0,5 Hz 1.8 Bestellnummern Tabelle A Variante Basic Basic ohne Display (Pure) Digitalmodule Analogmodule Bezeichnung Bestellnummer LOGO! 12/24RC * 6ED1 052-1MD00-0BA4 LOGO! 24 * 6ED1 052-1CC00-0BA4 LOGO! 24RC (AC) 6ED1 052-1HB00-0BA4 LOGO! 230RC 6ED1 052-1FB00-0BA4 LOGO! 12/24RCo * 6ED1 052-2MD00-0BA4 LOGO! 24o * 6ED1 052-2CC00-0BA4 LOGO! 24RCo (AC) 6ED1 052-2HB00-0BA4 LOGO! 230RCo 6ED1 052-2FB00-0BA4 LOGO! DM 8 12/24R 6ED1 055-1MB00-0BA1 LOGO! DM 8 24 6ED1 055-1CB00-0BA0 LOGO! DM 8 24R 6ED1 055-1HB00-0BA0 LOGO! DM 8 230R 6ED1 055-1FB00-0BA1 LOGO! DM 16 24 6ED1055-1CB10-0BA0 LOGO! DM 16 24R 6ED1055-1NB10-0BA0 LOGO! DM 16 230R 6ED1055-1FB10-0BA0 LOGO! AM 2 6ED1 055-1MA00-0BA0 LOGO! AM 2 PT100 6ED1 055-1MD00-0BA0 *: zusatzlich mit Analogeingangen Produktinformation LOGO! A5E00324307-01 13 Bestellnummern 14 Produktinformation LOGO! A5E00324307-01 Product information 07.2004 Product Information on Manual LOGO!; from Edition 06/2003 (A5E00228550-01) Preliminary remarks This Product Information contains additional information about LOGO! It is a separate component and should be considered more up-to-date than the information in the manuals and catalogs if uncertainties arise. This Product Information provides information about LOGO! expansion modules DM16 24, DM16 24R and DM16 230R. Copyright 2004 by Siemens AG A5E00324307-01 2.1 Which expansion modules are available? * LOGO! digital modules DM8... are available for operation with 12 V DC, 24 V AC/DC and 115...240 V AC/DC, and are equipped with four inputs and four outputs. * LOGO! digital modules DM16... are available for operation with 24 V DC and 115...240 V AC/DC, and are equipped with eight inputs and eight outputs. * LOGO! analog modules are available for operation with 12 V DC and 24 V DC, and are equipped with two analog inputs or two Pt100 inputs. * LOGO! communications modules (CM), for example the communications module AS interface, that is described in a separate documentation. The digital/analog modules are integrated in two or four subunits. Each one is equipped with two expansion interfaces for connecting additional modules. 2.2 The LOGO! structure 8 6 L+ M I1 I2 I3 I4 I5 I6 I7 I8 4 5 4 RUN/STOP 1 1 Q1 Q5 2 1 2 1 Q2 Q6 2 1 2 Q3 1 2 1 Q7 Q2 Q4 2 1 90 6 1 7 35 LOGO! expansion module (e.g.: DM16 24R) 2 7 2 Q8 2 3 72 1 Power supply 2 Inputs 3 Outputs 53 4 RUN/STOP indicator 7 Mechanical coding pins 5 Slide 8 6 Expansion interface Mechanical coding sockets Symbols The digital module is equipped with 4 digital inputs and 4 digital outputs The digital module is equipped with 8 digital inputs and 8 digital outputs 16 Product information LOGO! A5E00324307-01 2.3 Expansion modules The following expansion modules can be connected to the LOGO!: Symbol Name Power supply Inputs Outputs LOGO! DM 8 12/24R 12/24 V DC 4 digital 4 relays (5A) LOGO! DM 8 24 24 V DC 4 digital 4 solid state 24V / 0.3A LOGO! DM 8 24R (3) 24 V AC/DC 4 digital 4 relays (5A) LOGO! DM 8 230R 115...240 V AC/DC 4 digital (1) 4 relays (5A) LOGO! DM 16 24 24 V DC 8 digital 8 solid state 24V / 0.3A LOGO! DM 16 24R 24 V DC 8 digital 8 relays (5A) LOGO! DM 16 230R 115...240 V AC/DC 8 digital (4) 8 relays (5A) LOGO! AM 2 12/24 V DC 2 analog 0 ... 10V or 0 ... 20mA (2) none LOGO! AM 2 PT100 12/24 V DC 2 Pt100 -50 C to +200 C none (1): Different phases are not allowed within the inputs. (2): 0 ... 10 V, 0 ... 20 mA can be connected optionally. (3): Digital inputs can be operated either with P or with N action. (4): Two groups consisting of 4 inputs each. Each group must be connected to the same phase. It is possible to interconnect groups with a different phase. 2.4 Setup with different voltage classes Rules Digital modules can only be connected to devices of the same voltage class. You may connect analog and communications modules to devices of any voltage class. You may replace two similar DM8 expansion modules by one appropriate DM16 expansion module (and vice versa) without having to change the circuit program. Note Two DM8 12/24R may be replaced by one DM16 24R only if operated with a power supply of 24 V DC. Two DM8 24R may be replaced by one DM16 24R only if operated with DC and P action. Product information LOGO! A5E00324307-01 17 Overview: Connecting an expansion module to LOGO! Basic LOGO! B i Basic Expansion modules DM8 12/24R, DM16 24R DM8 24, DM16 24 DM8 24R DM8 230R, DM16 230R AM2, AM2 PT100 CM LOGO! 12/24RC x x x - x x LOGO! 24 x x x - x x LOGO! 24RC x x x - x x LOGO! 230RC - - - x x x LOGO! 12/24RCo x x x - x x LOGO! 24o x x x - x x LOGO! 24RCo x x x - x x LOGO! 230RCo - - - x x x Overview: Connecting a further expansion module to an expansion module Expansion module d l Further Expansion modules DM8 12/24R, DM16 24R DM8 24, DM16 24 DM 8 24R DM8 230R, DM16 230R AM2, AM2 PT100 CM DM 8 12/24R, DM 16 24R x x x - x x DM 8 24, DM 16 24 x x x - x x DM 8 24R x x x - x x DM 8 230R, DM 16 230R - - - x x x AM2 / AM2 PT100 x x x - x x CM x x x - x x 18 Product information LOGO! A5E00324307-01 2.5 Dimensions The LOGO! installation dimensions are compliant with DIN 43880. LOGO! can be snap-mounted to 35 mm DIN rails to EN 50022 or on the wall. LOGO! width: * LOGO! Basic has a width of 72 mm, which corresponds with 4 subunits. * LOGO! expansion modules have a width of 36 mm or 72 mm (DM16...), which corresponds with 2 or 4 subunits. 2.6 Connecting LOGO! inputs Sensor characteristics for LOGO! LOGO! DM16 24 R LOGO! DM16 24 LOGO! DM16 230 R (AC) LOGO! DM16 230 R (DC) Signal status 0 < 5 V DC < 5 V DC < 40 V AC < 30 V DC Input current < 1 mA < 1 mA < 0.05 mA < 0.05 mA Signal status 1 > 12 V DC > 12 V DC > 79 V AC > 79 V DC Input current > 2 mA > 2 mA > 0.08 mA > 0.08 mA Note The digital inputs of LOGO! 230 RC/RCo and of expansion module DM16 230R are divided into two groups, each consisting of four inputs. Within the same group, all inputs must be operated on the same phase. Different phases are only possible between the groups. Example: I1 to I4 on phase L1, I5 to I8 on phase L2. Inputs within the LOGO! DM8 230R may not be connected to different phases. Sensor connections Connecting glow lamps and 2-wire proximity switches (Bero) to LOGO! 230 RC/230 RCo or LOGO! DM8 230 R (AC) and LOGO! DM16 230R (AC) L1 N Order number for C: Siemens Switchgear & Systems C L1 3SB1420-3D N X-capacitor 2.5 kV, 100 nF Product information LOGO! A5E00324307-01 19 2.7 Technical data General technical data Criterion Tested in accordance with LOGO!Basic Dimensions (WxHxD) Weight Values 72 x 90 x 55 mm Approx. 190 g Installation on a 35 mm profile rail 4 module widths or wall mounting LOGO! expansion modules DM8..., AM... Dimensions (WxHxD) 36 x 90 x 53 mm Weight Approx. 90 g Installation on a 35 mm profile rail 2 module widths or wall mounting LOGO! expansion modules DM16... Dimensions (WxHxD) 72 x 90 x 53 mm Weight Approx. 190 g Installation on a 35 mm profile rail 4 module widths or wall mounting Climatic conditions Ambient temperature Horizontal installation Vertical installation Low temperature to IEC 60068-2-1 60068 21 High temperature to IEC 60068-2-2 -40 C ... +70 C Storage/shipping Relative humidity Air pressure Pollutants 0 ... 55 C C 0 ... 55 C IEC 60068-2-30 IEC 60068-2-42 IEC 60068-2-43 From 10 to 95 % no condensation 795 ... 1080 hPa SO2 10 cm3 /m3, 4 days H2S 1 cm3 /m3, 4 days Ambient mechanical conditions Protection mode IP20 Vibrations: IEC 60068-2-6 Shock IEC 60068-2-27 Drop IEC 60068-2-31 5 ... 9 Hz (constant amplitude 3.5 mm) 9 ... 150 Hz (constant acceleration 1 g) 18 shocks (half-sine wave 15g/11 ms) Drop height 50 mm Free fall (packaged) IEC 60068-2-32 Electromagnetic compatibility (EMC) 1m Noise emission Limit class B group 1 20 EN 55011/A EN 55022/B EN 50081-1 (domestic area) Product information LOGO! A5E00324307-01 Criterion Tested in accordance with IEC 61000-4-2 Severity 3 IEC 61000-4-3 8 kV air discharge 6 kV contact discharge Field strength 10 V/m IEC 61000-4-6 10 V IEC 61000-4-4 Severity 3 IEC 61000-4-5 Severity 3 2 kV (supply and signal lines) Clearance and creepage distance rating IEC 60664, IEC 61131-2, EN 50178 cULus to UL 508, CSA C22.2 No. 142 With LOGO! 230 R/RC, also VDE 0631 Fulfilled Insulation strength IEC 61131-2 Fulfilled Electrostatic discharge Electromagnetic fields HF currents on cables and cable shielding Burst pulses High-energy surge pulse (applies only to LOGO! 230 ...) Values 1 kV (power lines) symmetrical 2 kV (power lines) asymmetrical Safety to IEC / VDE Product information LOGO! A5E00324307-01 21 Technical data: LOGO! DM16 230R LOGO! DM16 230R Power supply Input voltage 115 ... 240 V AC/DC Permissible range 85 ... 265 V AC 100 ... 253 V DC Permissible mains frequency 47 ... 63 Hz Power consumption * * * * 115 V AC 10 ... 60 mA 240 V AC 10 ... 40 mA 115 V DC 5 ... 25 mA 240 V DC 5 ... 20 mA Voltage failure buffering * 115 V AC/DC * 240 V AC/DC typ typ. yp 10 ms typ. typ 20 ms Power loss at * * * * 115 V AC 1.1 ... 4.5 W 240 V AC 2.4 ... 5.5 W 115 V DC 0.6 ... 2.9 W 240 V DC 1.2 ... 4.8 W Backup of the real-time clock at 25 _C Accuracy of the real-time clock Digital inputs Number 8 Electrical isolation No Input voltage L1 * * * * Signal 0 < 40 V AC Signal 1 > 79 V AC Signal 0 < 30 V DC Signal 1 > 79 V DC Input current at * Signal g 0 * Signal 1 < 0.05 mA > 0.08 mA Delay time at * 0 to 1 * 1 to 0 typ. yp 50 ms Line length (unshielded) 100 m typ. 50 ms Digital outputs Number 8 Output type Relay outputs Electrical isolation Yes In groups of 1 Control of a digital input Yes 22 Product information LOGO! A5E00324307-01 LOGO! DM16 230R Continuous current Ith max. 5 A per relay Incandescent lamp load (25000 switching cycles) at 230/240 V AC 1000 W 115/120 V AC 500 W Fluorescent tubes with ballast (25000 switching cycles) 10 x 58 W (at 230/240 V AC) Fluorescent tubes, conventionally compensated (25000 switching cycles) 1 x 58 W (at 230/240 V AC) Fluorescent tubes, uncompensated (25000 switching cycles) 10 x 58 W (at 230/240 V AC) Short circuit-proof cos 1 Power protection B16 600A Short-circuit proof cos 0.5 to 0.7 Power protection B16 900A Derating None; across the entire temperature range Parallel output circuits for power increase Not permitted Protection of output relay (if desired) max. 16 A, characteristic B16 Switching rate Mechanical 10 Hz Ohmic load/lamp load 2 Hz Inductive load 0.5 Hz Product information LOGO! A5E00324307-01 23 Technical data: LOGO! DM16 24 LOGO! DM16 24 Power supply Input voltage 24 V DC Permissible range 20.4 ... 28.8 V DC Reverse polarity protection Yes Permissible mains frequency Power consumption from 24 V DC 30 ... 45 mA 0.3 A per output Voltage failure buffering Power loss at 24 V 0.8 ... 1.7 W Backup of the real-time clock at 25 _C Accuracy of the real-time clock Digital inputs Number 8 Electrical isolation No Input voltage L+ * Signal g 0 * Signal 1 < 5 V DC > 12 V DC Input current at * Signal g 0 * Signal 1 < 1 mA > 2 mA Delay time at * 0 to 1 * 1 to 0 typ. yp 1.5 ms Line length (unshielded) 100 m typ. 1.5 ms Digital outputs Number 8 Output type Transistor, current-sourcing Electrical isolation No In groups of Control of a digital input Yes Output voltage Supply voltage Output current max. 0.3 A Continuous current Ith Incandescent lamp load (25000 switching cycles) at Fluorescent tubes with ballast (25000 switching cycles) Fluorescent tubes, conventionally compensated (25000 switching cycles) Fluorescent tubes, uncompensated (25000 switching cycles) 24 Product information LOGO! A5E00324307-01 LOGO! DM16 24 Short circuit-proof and overload-proof Yes Short-circuit current limitation Approx. 1 A Derating None; across the entire temperature range Short circuit-proof cos 1 Short-circuit proof cos 0.5 to 0.7 Parallel output circuit for power increase Not permitted Protection of output relay (if desired) Switching rate Mechanical Electrical 10 Hz Ohmic load/lamp load 10 Hz Inductive load 0.5 Hz Product information LOGO! A5E00324307-01 25 Technical data: LOGO! DM16 24R LOGO! DM16 24R Power supply Input voltage 24 V DC Permissible range 20.4 ... 28.8 V DC Reverse polarity protection Yes Power consumption from 24 V DC 30 ... 90 mA Voltage failure buffering * 24 V DC typ. 5 ms Power loss at 24 V * 24 V DC 0.7 ... 2.5 W Backup of the real-time clock at 25 _C Accuracy of the real-time clock Electrical isolation No Digital inputs Number 8 Electrical isolation No Input voltage * Signal g 0 * Signal 1 < 5 V DC > 12 V DC Input current at * Signal g 0 * Signal 1 < 1 mA > 2 mA Delay time at * 0 to 1 * 1 to 0 typ. yp 1.5 ms Line length (unshielded) 100 m typ. 1.5 ms Digital outputs Number 8 Output type Relay outputs Electrical isolation Yes In groups of 1 Control of a digital input Yes Output voltage Output current Continuous current Ith max. 5 A per relay Incandescent lamp load (25000 switching cycles) at 1000 W Fluorescent tubes with ballast (25000 switching cycles) 10 x 58 W Fluorescent tubes, conventionally compensated (25000 switching cycles) 1 x 58 W 26 Product information LOGO! A5E00324307-01 LOGO! DM16 24R Fluorescent tubes, uncompensated (25000 switching cycles) 10 x 58 W Short circuit-proof and overload-proof Short-circuit current limitation Derating None; across the entire temperature range Short circuit-proof cos 1 Power protection B16 600A Short-circuit proof cos 0.5 to 0.7 Power protection B16 900A Parallel output circuit for power increase Not permitted Protection of output relay (if desired) max. 16 A, characteristic B16 Switching rate Mechanical 10 Hz Electrical Ohmic load/lamp load 2 Hz Inductive load 0.5 Hz 2.8 Order numbers Table A Variant Basic Basic without display (pure) Digital modules Analog modules Designation Order number LOGO! 12/24RC * 6ED1 052-1MD00-0BA4 LOGO! 24 * 6ED1 052-1CC00-0BA4 LOGO! 24RC (AC) 6ED1 052-1HB00-0BA4 LOGO! 230RC 6ED1 052-1FB00-0BA4 LOGO! 12/24RCo * 6ED1 052-2MD00-0BA4 LOGO! 24o * 6ED1 052-2CC00-0BA4 LOGO! 24RCo (AC) 6ED1 052-2HB00-0BA4 LOGO! 230RCo 6ED1 052-2FB00-0BA4 LOGO! DM 8 12/24R 6ED1 055-1MB00-0BA1 LOGO! DM 8 24 6ED1 055-1CB00-0BA0 LOGO! DM 8 24R 6ED1 055-1HB00-0BA0 LOGO! DM 8 230R 6ED1 055-1FB00-0BA1 LOGO! DM 16 24 6ED1055-1CB10-0BA0 LOGO! DM 16 24R 6ED1055-1NB10-0BA0 LOGO! DM 16 230R 6ED1055-1FB10-0BA0 LOGO! AM 2 6ED1 055-1MA00-0BA0 LOGO! AM 2 PT100 6ED1 055-1MD00-0BA0 *: Also with analog inputs Product information LOGO! A5E00324307-01 27 Bestellnummern 28 Product information LOGO! A5E00324307-01