GS8161Z18(T/D)/GS8161Z32(D)/GS8161Z36(T/D) 100-Pin TQFP Commercial Temp Industrial Temp 18Mb Pipelined and Flow Through Synchronous NBT SRAM Features 250 MHz-133 MHz 2.5 V or 3.3 V VDD 2.5 V or 3.3 V I/O Because it is a synchronous device, address, data inputs, and read/ write control inputs are captured on the rising edge of the input clock. Burst order control (LBO) must be tied to a power rail for proper operation. Asynchronous inputs include the Sleep mode enable, ZZ and Output Enable. Output Enable can be used to override the synchronous control of the output drivers and turn the RAM's output drivers off at any time. Write cycles are internally self-timed and initiated by the rising edge of the clock input. This feature eliminates complex offchip write pulse generation required by asynchronous SRAMs and simplifies input signal timing. * User-configurable Pipeline and Flow Through mode * NBT (No Bus Turn Around) functionality allows zero wait read-write-read bus utilization * Fully pin-compatible with both pipelined and flow through NtRAMTM, NoBLTM and ZBTTM SRAMs * IEEE 1149.1 JTAG-compatible Boundary Scan * 2.5 V or 3.3 V +10%/-10% core power supply * LBO pin for Linear or Interleave Burst mode * Pin-compatible with 2M, 4M, and 8M devices * Byte write operation (9-bit Bytes) * 3 chip enable signals for easy depth expansion * ZZ pin for automatic power-down * JEDEC-standard 100-lead TQFP and 165-bump FP-BGA packages The GS8161Z18(T/D)/GS8161Z32(D)/GS8161Z36(T/D) may be configured by the user to operate in Pipeline or Flow Through mode. Operating as a pipelined synchronous device, in addition to the rising-edge-triggered registers that capture input signals, the device incorporates a rising-edge-triggered output register. For read cycles, pipelined SRAM output data is temporarily stored by the edge triggered output register during the access cycle and then released to the output drivers at the next rising edge of clock. Functional Description The GS8161Z18(T/D)/GS8161Z32(D)/GS8161Z36(T/D) is an 18Mbit Synchronous Static SRAM. GSI's NBT SRAMs, like ZBT, NtRAM, NoBL or other pipelined read/double late write or flow through read/single late write SRAMs, allow utilization of all available bus bandwidth by eliminating the need to insert deselect cycles when the device is switched from read to write cycles. The GS8161Z18(T/D)/GS8161Z32(D)/GS8161Z36(T/D) is implemented with GSI's high performance CMOS technology and is available in JEDEC-standard 100-pin TQFP and 165-bump FP-BGA packages. Parameter Synopsis Pipeline 3-1-1-1 3.3 V 2.5 V Flow Through 2-1-1-1 3.3 V 2.5 V Rev: 2.14c 1/2004 tKQ tCycle Curr (x18) Curr (x32/x36) Curr (x18) Curr (x32/x36) -250 -225 -200 -166 -150 -133 Unit 2.5 2.7 3.0 3.4 3.8 4.0 ns 4.0 4.4 5.0 6.0 6.7 7.5 ns 280 330 275 320 255 300 250 295 230 270 230 265 200 230 195 225 185 215 180 210 165 190 165 185 mA mA mA mA tKQ tCycle 5.5 5.5 6.0 6.0 6.5 6.5 7.0 7.0 7.5 7.5 8.5 8.5 ns ns Curr (x18) Curr (x32/x36) Curr (x18) Curr (x32/x36) 175 200 175 200 165 190 165 190 160 180 160 180 150 170 150 170 145 165 145 165 135 150 135 150 mA mA mA mA 1/39 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 1998, Giga Semiconductor, Inc. NoBL is a trademark of Cypress Semiconductor Corp.. NtRAM is a trademark of Samsung Electronics Co.. ZBT is a trademark of Integrated Device Technology, Inc. GS8161Z18(T/D)/GS8161Z32(D)/GS8161Z36(T/D) A A E1 E2 NC NC BB BA E3 VDD VSS CK W CKE G ADV A A A A GS8161Z18T Pinout NC NC NC VDDQ A NC NC VDDQ VSS NC DQPA DQA DQA VSS VDDQ DQA DQA VSS NC VDD ZZ DQA DQA VDDQ VSS DQA DQA NC NC VSS VDDQ NC NC NC LBO A A A A A1 A0 TMS TDI VSS VDD TDO TCK A A A A A A A VSS NC NC DQB DQB VSS VDDQ DQB DQB FT VDD NC VSS DQB DQB VDDQ VSS DQB DQB DQPB NC VSS VDDQ NC NC NC 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 1 80 2 79 3 78 4 77 5 76 6 75 7 74 8 73 9 72 1M x 18 10 71 11 Top View 70 12 69 13 68 14 67 15 66 16 65 17 64 18 63 19 62 20 61 21 60 22 59 23 58 24 57 25 56 26 55 27 54 28 53 29 52 30 51 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 Rev: 2.14c 1/2004 2/39 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 1998, Giga Semiconductor, Inc. GS8161Z18(T/D)/GS8161Z32(D)/GS8161Z36(T/D) A A E1 E2 BD BC BB BA E3 VDD VSS CK W CKE G ADV A A A A GS8161Z36T Pinout DQPC DQC DQC VDDQ DQPB DQB DQB VDDQ VSS DQB DQB DQB DQB VSS VDDQ DQB DQB VSS NC VDD ZZ DQA DQA VDDQ VSS DQA DQA DQA DQA VSS VDDQ DQA DQA DQPA LBO A A A A A1 A0 TMS TDI VSS VDD TDO TCK A A A A A A A VSS DQC DQC DQC DQC VSS VDDQ DQC DQC FT VDD NC VSS DQD1 DQD VDDQ VSS DQD DQD DQD DQD VSS VDDQ DQD DQD DQPD 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 1 80 2 79 3 78 4 77 5 76 6 75 7 74 8 73 9 72 512K x 36 10 71 11 Top View 70 12 69 13 68 14 67 15 66 16 65 17 64 18 63 19 62 20 61 21 60 22 59 23 58 24 57 25 56 26 55 27 54 28 53 29 52 30 51 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 Rev: 2.14c 1/2004 3/39 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 1998, Giga Semiconductor, Inc. GS8161Z18(T/D)/GS8161Z32(D)/GS8161Z36(T/D) 100-Pin TQFP Pin Descriptions Symbol Type Description A 0, A 1 In Burst Address Inputs; Preload the burst counter A In Address Inputs CK In Clock Input Signal BA In Byte Write signal for data inputs DQA1-DQA9; active low BB In Byte Write signal for data inputs DQB1-DQB9; active low BC In Byte Write signal for data inputs DQC1-DQC9; active low BD In Byte Write signal for data inputs DQD1-DQD9; active low W In Write Enable; active low E1 In Chip Enable; active low E2 In Chip Enable--Active High. For self decoded depth expansion E3 In Chip Enable--Active Low. For self decoded depth expansion G In Output Enable; active low ADV In Advance/Load; Burst address counter control pin CKE In Clock Input Buffer Enable; active low NC -- No Connect DQA I/O Byte A Data Input and Output pins DQB I/O Byte B Data Input and Output pins DQC I/O Byte C Data Input and Output pins DQD I/O Byte D Data Input and Output pins TMS I Scan Test Mode Select TDI I Scan Test Data In TDO O Scan Test Data Out TCK I Scan Test Clock ZZ In Power down control; active high FT In Pipeline/Flow Through Mode Control; active low LBO In Linear Burst Order; active low. VDD In Core power supply VSS In Ground VDDQ In Output driver power supply Rev: 2.14c 1/2004 4/39 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 1998, Giga Semiconductor, Inc. GS8161Z18(T/D)/GS8161Z32(D)/GS8161Z36(T/D) 165 Bump BGA--x18 Commom I/O--Top View (Package D) 1 2 3 4 5 6 7 8 9 10 11 A NC A E1 BB NC E3 CKE ADV A A A A B NC A E2 NC BA CK W G A A NC B C NC NC VDDQ VSS VSS VSS VSS VSS VDDQ NC DQPA C D NC DQB VDDQ VDD VSS VSS VSS VDD VDDQ NC DQA D E NC DQB VDDQ VDD VSS VSS VSS VDD VDDQ NC DQA E F NC DQB VDDQ VDD VSS VSS VSS VDD VDDQ NC DQA F G NC DQB VDDQ VDD VSS VSS VSS VDD VDDQ NC DQA G H FT MCH NC VDD VSS VSS VSS VDD NC NC ZZ H J DQB NC VDDQ VDD VSS VSS VSS VDD VDDQ DQA NC J K DQB NC VDDQ VDD VSS VSS VSS VDD VDDQ DQA NC K L DQB NC VDDQ VDD VSS VSS VSS VDD VDDQ DQA NC L M DQB NC VDDQ VDD VSS VSS VSS VDD VDDQ DQA NC M N DQPB NC VDDQ VSS NC NC NC VSS VDDQ NC NC N P NC NC A A TDI A1 TDO A A A NC P R LBO NC A A TMS A0 TCK A A A A R 11 x 15 Bump BGA--13 mm x 15 mm Body--1.0 mm Bump Pitch Rev: 2.14c 1/2004 5/39 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 1998, Giga Semiconductor, Inc. GS8161Z18(T/D)/GS8161Z32(D)/GS8161Z36(T/D) 165 Bump BGA--x32 Common I/O--Top View (Package D) 1 2 3 4 5 6 7 8 9 10 11 A NC A E1 BC BB E3 CKE ADV A A NC A B NC A E2 BD BA CK W G A A NC B C NC NC VDDQ VSS VSS VSS VSS VSS VDDQ NC NC C D DQC DQC VDDQ VDD VSS VSS VSS VDD VDDQ DQB DQB D E DQC DQC VDDQ VDD VSS VSS VSS VDD VDDQ DQB DQB E F DQC DQC VDDQ VDD VSS VSS VSS VDD VDDQ DQB DQB F G DQC DQC VDDQ VDD VSS VSS VSS VDD VDDQ DQB DQB G H FT MCH NC VDD VSS VSS VSS VDD NC NC ZZ H J DQD DQD VDDQ VDD VSS VSS VSS VDD VDDQ DQA DQA J K DQD DQD VDDQ VDD VSS VSS VSS VDD VDDQ DQA DQA K L DQD DQD VDDQ VDD VSS VSS VSS VDD VDDQ DQA DQA L M DQD DQD VDDQ VDD VSS VSS VSS VDD VDDQ DQA DQA M N NC NC VDDQ VSS NC NC NC VSS VDDQ NC NC N P NC NC A A TDI A1 TDO A A A NC P R LBO NC A A TMS A0 TCK A A A A R 11 x 15 Bump BGA--13 mm x 15 mm Body--1.0 mm Bump Pitch Rev: 2.14c 1/2004 6/39 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 1998, Giga Semiconductor, Inc. GS8161Z18(T/D)/GS8161Z32(D)/GS8161Z36(T/D) 165 Bump BGA--x36 Common I/O--Top View (Package D) 1 2 3 4 5 6 7 8 9 10 11 A NC A E1 BC BB E3 CKE ADV A A NC A B NC A E2 BD BA CK W G A A NC B C DQPC NC VDDQ VSS VSS VSS VSS VSS VDDQ NC DQPB C D DQC DQC VDDQ VDD VSS VSS VSS VDD VDDQ DQB DQB D E DQC DQC VDDQ VDD VSS VSS VSS VDD VDDQ DQB DQB E F DQC DQC VDDQ VDD VSS VSS VSS VDD VDDQ DQB DQB F G DQC DQC VDDQ VDD VSS VSS VSS VDD VDDQ DQB DQB G H FT MCH NC VDD VSS VSS VSS VDD NC NC ZZ H J DQD DQD VDDQ VDD VSS VSS VSS VDD VDDQ DQA DQA J K DQD DQD VDDQ VDD VSS VSS VSS VDD VDDQ DQA DQA K L DQD DQD VDDQ VDD VSS VSS VSS VDD VDDQ DQA DQA L M DQD DQD VDDQ VDD VSS VSS VSS VDD VDDQ DQA DQA M N DQPD NC VDDQ VSS NC NC NC VSS VDDQ NC DQPA N P NC NC A A TDI A1 TDO A A A NC P R LBO NC A A TMS A0 TCK A A A A R 11 x 15 Bump BGA--13 mm x 15 mm Body--1.0 mm Bump Pitch Rev: 2.14c 1/2004 7/39 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 1998, Giga Semiconductor, Inc. GS8161Z18(T/D)/GS8161Z32(D)/GS8161Z36(T/D) GS8161Z18/32/36D 165-Bump BGA Pin Description Symbol Type Description A 0, A 1 I Address field LSBs and Address Counter Preset Inputs An I Address Inputs DQA DQB DQC DQD I/O Data Input and Output pins BA , BB , BC , BD I Byte Write Enable for DQA, DQB, DQC, DQD I/Os; active low NC -- No Connect CK I Clock Input Signal; active high CKE I Clock Input Buffer Enable; active low W I Write Enable; active low E1 I Chip Enable; active low E3 I Chip Enable; active low E2 I Chip Enable; active high G I Output Enable; active low ADV I Burst address counter advance enable; active high ZZ I Sleep mode control; active high FT I Flow Through or Pipeline mode; active low LBO I Linear Burst Order mode; active low TMS I Scan Test Mode Select TDI I Scan Test Data In TDO O Scan Test Data Out TCK I Scan Test Clock MCH -- Must Connect High VDD I Core power supply VSS I I/O and Core Ground VDDQ I Output driver power supply Rev: 2.14c 1/2004 8/39 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 1998, Giga Semiconductor, Inc. GS8161Z18(T/D)/GS8161Z32(D)/GS8161Z36(T/D) Sense Amps Memory Array Register 2 Write Data K Register 1 K D Write Data Q K FT DQa-DQn GS8161Z18/32/36 NBT SRAM Functional Block Diagram FT Register 2 Register 1 Control Logic 9/39 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. G CKE CK E3 E2 E1 BD BC BB BA W LBO ADV A0-An K K Data Coherency Match Read, Write and K Write Address Write Address K K D Q SA1 SA0 Burst Counter SA1' SA0' 18 Write Drivers Rev: 2.14c 1/2004 (c) 1998, Giga Semiconductor, Inc. GS8161Z18(T/D)/GS8161Z32(D)/GS8161Z36(T/D) Functional Details Clocking Deassertion of the Clock Enable (CKE) input blocks the Clock input from reaching the RAM's internal circuits. It may be used to suspend RAM operations. Failure to observe Clock Enable set-up or hold requirements will result in erratic operation. Pipeline Mode Read and Write Operations All inputs (with the exception of Output Enable, Linear Burst Order and Sleep) are synchronized to rising clock edges. Single cycle read and write operations must be initiated with the Advance/Load pin (ADV) held low, in order to load the new address. Device activation is accomplished by asserting all three of the Chip Enable inputs (E1, E2 and E3). Deassertion of any one of the Enable inputs will deactivate the device. Function W BA BB BC BD Read H X X X X Write Byte "a" L L H H H Write Byte "b" L H L H H Write Byte "c" L H H L H Write Byte "d" L H H H L Write all Bytes L L L L L Write Abort/NOP L H H H H Read operation is initiated when the following conditions are satisfied at the rising edge of clock: CKE is asserted low, all three chip enables (E1, E2, and E3) are active, the write enable input signals W is deasserted high, and ADV is asserted low. The address presented to the address inputs is latched in to address register and presented to the memory core and control logic. The control logic determines that a read access is in progress and allows the requested data to propagate to the input of the output register. At the next rising edge of clock the read data is allowed to propagate through the output register and onto the output pins. Write operation occurs when the RAM is selected, CKE is active and the write input is sampled low at the rising edge of clock. The Byte Write Enable inputs (BA, BB, BC & BD) determine which bytes will be written. All or none may be activated. A write cycle with no Byte Write inputs active is a no-op cycle. The pipelined NBT SRAM provides double late write functionality, matching the write command versus data pipeline length (2 cycles) to the read command versus data pipeline length (2 cycles). At the first rising edge of clock, Enable, Write, Byte Write(s), and Address are registered. The Data In associated with that address is required at the third rising edge of clock. Flow Through Mode Read and Write Operations Operation of the RAM in Flow Through mode is very similar to operations in Pipeline mode. Activation of a read cycle and the use of the Burst Address Counter is identical. In Flow Through mode the device may begin driving out new data immediately after new address are clocked into the RAM, rather than holding new data until the following (second) clock edge. Therefore, in Flow Through mode the read pipeline is one cycle shorter than in Pipeline mode. Write operations are initiated in the same way, but differ in that the write pipeline is one cycle shorter as well, preserving the ability to turn the bus from reads to writes without inserting any dead cycles. While the pipelined NBT RAMs implement a double late write protocol, in Flow Through mode a single late write protocol mode is observed. Therefore, in Flow Through mode, address and control are registered on the first rising edge of clock and data in is required at the data input pins at the second rising edge of clock. Rev: 2.14c 1/2004 10/39 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 1998, Giga Semiconductor, Inc. GS8161Z18(T/D)/GS8161Z32(D)/GS8161Z36(T/D) Synchronous Truth Table Operation Type Address CK CKE ADV W Bx E1 E2 E3 G ZZ DQ Notes Read Cycle, Begin Burst R External L-H L L H X L H L L L Q Read Cycle, Continue Burst B Next L-H L H X X X X X L L Q 1,10 NOP/Read, Begin Burst R External L-H L L H X L H L H L High-Z 2 Dummy Read, Continue Burst B Next L-H L H X X X X X H L High-Z 1,2,10 Write Cycle, Begin Burst W External L-H L L L L L H L X L D 3 Write Cycle, Continue Burst B Next L-H L H X L X X X X L D 1,3,10 Write Abort, Continue Burst B Next L-H L H X H X X X X L High-Z 1,2,3,10 Deselect Cycle, Power Down D None L-H L L X X H X X X L High-Z Deselect Cycle, Power Down D None L-H L L X X X X H X L High-Z Deselect Cycle, Power Down D None L-H L L X X X L X X L High-Z Deselect Cycle D None L-H L L L H L H L X L High-Z 1 Deselect Cycle, Continue D None L-H L H X X X X X X L High-Z 1 None X X X X X X X X X H High-Z Current L-H H X X X X X X X L - Sleep Mode Clock Edge Ignore, Stall 4 Notes: 1. Continue Burst cycles, whether read or write, use the same control inputs. A Deselect continue cycle can only be entered into if a Deselect cycle is executed first. 2. Dummy Read and Write abort can be considered NOPs because the SRAM performs no operation. A Write abort occurs when the W pin is sampled low but no Byte Write pins are active so no write operation is performed. 3. G can be wired low to minimize the number of control signals provided to the SRAM. Output drivers will automatically turn off during write cycles. 4. If CKE High occurs during a pipelined read cycle, the DQ bus will remain active (Low Z). If CKE High occurs during a write cycle, the bus will remain in High Z. 5. X = Don't Care; H = Logic High; L = Logic Low; Bx = High = All Byte Write signals are high; Bx = Low = One or more Byte/Write signals are Low 6. All inputs, except G and ZZ must meet setup and hold times of rising clock edge. 7. Wait states can be inserted by setting CKE high. 8. This device contains circuitry that ensures all outputs are in High Z during power-up. 9. A 2-bit burst counter is incorporated. 10. The address counter is incriminated for all Burst continue cycles. Rev: 2.14c 1/2004 11/39 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 1998, Giga Semiconductor, Inc. GS8161Z18(T/D)/GS8161Z32(D)/GS8161Z36(T/D) Pipelined and Flow Through Read Write Control State Diagram D B Deselect W R D R D W New Read New Write R W B B R B W R Burst Read W Burst Write D Key B D Notes: Input Command Code 1. The Hold command (CKE Low) is not shown because it prevents any state change. Transition Current State (n) 2. W, R, B, and D represent input command codes as indicated in the Synchronous Truth Table. Next State (n+1) n n+1 n+2 n+3 Clock (CK) Command Current State Next State Current State and Next State Definition for Pipelined and Flow Through Read/Write Control State Diagram Rev: 2.14c 1/2004 12/39 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 1998, Giga Semiconductor, Inc. GS8161Z18(T/D)/GS8161Z32(D)/GS8161Z36(T/D) Pipeline Mode Data I/O State Diagram Intermediate B W R B Intermediate R High Z (Data In) D Data Out (Q Valid) W D Intermediate Intermediate W Intermediate R High Z B D Intermediate Key Notes: Input Command Code 1. The Hold command (CKE Low) is not shown because it prevents any state change. Transition Current State (n) Transition Intermediate State (N+1) n Next State (n+2) n+1 2. W, R, B, and D represent input command codes as indicated in the Truth Tables. n+2 n+3 Clock (CK) Command Current State Intermediate State Next State Current State and Next State Definition for Pipeline Mode Data I/O State Diagram Rev: 2.14c 1/2004 13/39 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 1998, Giga Semiconductor, Inc. GS8161Z18(T/D)/GS8161Z32(D)/GS8161Z36(T/D) Flow Through Mode Data I/O State Diagram B W R B R High Z (Data In) Data Out (Q Valid) W D D W R High Z B D Key Notes: Input Command Code 1. The Hold command (CKE Low) is not shown because it prevents any state change. Transition Current State (n) 2. W, R, B, and D represent input command codes as indicated in the Truth Tables. Next State (n+1) n n+1 n+2 n+3 Clock (CK) Command Current State Next State Current State and Next State Definition for: Pipeline and Flow through Read Write Control State Diagram Rev: 2.14c 1/2004 14/39 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 1998, Giga Semiconductor, Inc. GS8161Z18(T/D)/GS8161Z32(D)/GS8161Z36(T/D) Burst Cycles Although NBT RAMs are designed to sustain 100% bus bandwidth by eliminating turnaround cycle when there is transition from read to write, multiple back-to-back reads or writes may also be performed. NBT SRAMs provide an on-chip burst address generator that can be utilized, if desired, to further simplify burst read or write implementations. The ADV control pin, when driven high, commands the SRAM to advance the internal address counter and use the counter generated address to read or write the SRAM. The starting address for the first cycle in a burst cycle series is loaded into the SRAM by driving the ADV pin low, into Load mode. Burst Order The burst address counter wraps around to its initial state after four addresses (the loaded address and three more) have been accessed. The burst sequence is determined by the state of the Linear Burst Order pin (LBO). When this pin is low, a linear burst sequence is selected. When the RAM is installed with the LBO pin tied high, Interleaved burst sequence is selected. See the tables below for details. Mode Pin Functions Mode Name Pin Name Burst Order Control LBO Output Register Control FT Power Down Control ZZ State Function L Linear Burst H Interleaved Burst L Flow Through H or NC Pipeline L or NC Active H Standby, IDD = ISB Note: There are pull-up devices on the FT pin and a pull-down device on the ZZ pin, so those input pins can be unconnected and the chip will operate in the default states as specified in the above tables. Burst Counter Sequences Linear Burst Sequence Interleaved Burst Sequence A[1:0] A[1:0] A[1:0] A[1:0] A[1:0] A[1:0] A[1:0] A[1:0] 1st address 00 01 10 11 1st address 00 01 10 11 2nd address 01 10 11 00 2nd address 01 00 11 10 3rd address 10 11 00 01 3rd address 10 11 00 01 4th address 11 00 01 10 4th address 11 10 01 00 Note: The burst counter wraps to initial state on the 5th clock. Note: The burst counter wraps to initial state on the 5th clock. BPR 1999.05.18 Rev: 2.14c 1/2004 15/39 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 1998, Giga Semiconductor, Inc. GS8161Z18(T/D)/GS8161Z32(D)/GS8161Z36(T/D) Sleep Mode During normal operation, ZZ must be pulled low, either by the user or by it's internal pull down resistor. When ZZ is pulled high, the SRAM will enter a Power Sleep mode after 2 cycles. At this time, internal state of the SRAM is preserved. When ZZ returns to low, the SRAM operates normally after ZZ recovery time. Sleep mode is a low current, power-down mode in which the device is deselected and current is reduced to ISB2. The duration of Sleep mode is dictated by the length of time the ZZ is in a high state. After entering Sleep mode, all inputs except ZZ become disabled and all outputs go to High-Z The ZZ pin is an asynchronous, active high input that causes the device to enter Sleep mode. When the ZZ pin is driven high, ISB2 is guaranteed after the time tZZI is met. Because ZZ is an asynchronous input, pending operations or operations in progress may not be properly completed if ZZ is asserted. Therefore, Sleep mode must not be initiated until valid pending operations are completed. Similarly, when exiting Sleep mode during tZZR, only a Deselect or Read commands may be applied while the SRAM is recovering from Sleep mode. Sleep Mode Timing Diagram tKH tKC tKL CK tZZR tZZS tZZH ZZ Designing for Compatibility The GSI NBT SRAMs offer users a configurable selection between Flow Through mode and Pipelinemode via the FT signal found on Pin 14. Not all vendors offer this option, however most mark Pin 14 as VDD or VDDQ on pipelined parts and VSS on flow through parts. GSI NBT SRAMs are fully compatible with these sockets. Rev: 2.14c 1/2004 16/39 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 1998, Giga Semiconductor, Inc. GS8161Z18(T/D)/GS8161Z32(D)/GS8161Z36(T/D) Absolute Maximum Ratings (All voltages reference to VSS) Symbol Description Value Unit VDD Voltage on VDD Pins -0.5 to 4.6 V VDDQ Voltage in VDDQ Pins -0.5 to 4.6 V VI/O Voltage on I/O Pins -0.5 to VDDQ +0.5 ( 4.6 V max.) V VIN Voltage on Other Input Pins -0.5 to VDD +0.5 ( 4.6 V max.) V IIN Input Current on Any Pin +/-20 mA IOUT Output Current on Any I/O Pin +/-20 mA PD Package Power Dissipation 1.5 W TSTG Storage Temperature -55 to 125 o -55 to 125 o TBIAS Temperature Under Bias C C Note: Permanent damage to the device may occur if the Absolute Maximum Ratings are exceeded. Operation should be restricted to Recommended Operating Conditions. Exposure to conditions exceeding the Absolute Maximum Ratings, for an extended period of time, may affect reliability of this component. Power Supply Voltage Ranges Parameter Symbol Min. Typ. Max. Unit 3.3 V Supply Voltage VDD3 3.0 3.3 3.6 V 2.5 V Supply Voltage VDD2 2.3 2.5 2.7 V 3.3 V VDDQ I/O Supply Voltage VDDQ3 3.0 3.3 3.6 V 2.5 V VDDQ I/O Supply Voltage VDDQ2 2.3 2.5 2.7 V Notes Notes: 1. The part numbers of Industrial Temperature Range versions end the character "I". Unless otherwise noted, all performance specifications quoted are evaluated for worst case in the temperature range marked on the device. 2. Input Under/overshoot voltage must be -2 V > Vi < VDDn+2 V not to exceed 4.6 V maximum, with a pulse width not to exceed 20% tKC. Rev: 2.14c 1/2004 17/39 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 1998, Giga Semiconductor, Inc. GS8161Z18(T/D)/GS8161Z32(D)/GS8161Z36(T/D) VDDQ3 Range Logic Levels Parameter Symbol Min. Typ. Max. Unit Notes VDD Input High Voltage VIH 2.0 -- VDD + 0.3 V 1 VDD Input Low Voltage VIL -0.3 -- 0.8 V 1 VDDQ I/O Input High Voltage VIHQ 2.0 -- VDDQ + 0.3 V 1,3 VDDQ I/O Input Low Voltage VILQ -0.3 -- 0.8 V 1,3 Notes: 1. The part numbers of Industrial Temperature Range versions end the character "I". Unless otherwise noted, all performance specifications quoted are evaluated for worst case in the temperature range marked on the device. 2. Input Under/overshoot voltage must be -2 V > Vi < VDDn+2 V not to exceed 4.6 V maximum, with a pulse width not to exceed 20% tKC. 3. VIHQ (max) is voltage on VDDQ pins plus 0.3 V. VDDQ2 Range Logic Levels Parameter Symbol Min. Typ. Max. Unit Notes VDD Input High Voltage VIH 0.6*VDD -- VDD + 0.3 V 1 VDD Input Low Voltage VIL -0.3 -- 0.3*VDD V 1 VDDQ I/O Input High Voltage VIHQ 0.6*VDD -- VDDQ + 0.3 V 1,3 VDDQ I/O Input Low Voltage VILQ -0.3 -- 0.3*VDD V 1,3 Notes: 1. The part numbers of Industrial Temperature Range versions end the character "I". Unless otherwise noted, all performance specifications quoted are evaluated for worst case in the temperature range marked on the device. 2. Input Under/overshoot voltage must be -2 V > Vi < VDDn+2 V not to exceed 4.6 V maximum, with a pulse width not to exceed 20% tKC. 3. VIHQ (max) is voltage on VDDQ pins plus 0.3 V. Recommended Operating Temperatures Parameter Symbol Min. Typ. Max. Unit Notes Ambient Temperature (Commercial Range Versions) TA 0 25 70 C 2 Ambient Temperature (Industrial Range Versions) TA -40 25 85 C 2 Notes: 1. The part numbers of Industrial Temperature Range versions end the character "I". Unless otherwise noted, all performance specifications quoted are evaluated for worst case in the temperature range marked on the device. 2. Input Under/overshoot voltage must be -2 V > Vi < VDDn+2 V not to exceed 4.6 V maximum, with a pulse width not to exceed 20% tKC. Rev: 2.14c 1/2004 18/39 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 1998, Giga Semiconductor, Inc. GS8161Z18(T/D)/GS8161Z32(D)/GS8161Z36(T/D) Undershoot Measurement and Timing Overshoot Measurement and Timing VIH 20% tKC VDD + 2.0 V VSS 50% 50% VDD VSS - 2.0 V 20% tKC VIL Capacitance (TA = 25oC, f = 1 MHZ, VDD = 2.5 V) Parameter Symbol Test conditions Typ. Max. Unit Input Capacitance CIN VIN = 0 V 4 5 pF Input/Output Capacitance CI/O VOUT = 0 V 6 7 pF Note: These parameters are sample tested. AC Test Conditions Parameter Conditions Input high level VDD - 0.2 V Input low level 0.2 V Input slew rate 1 V/ns Input reference level VDD/2 Output reference level VDDQ/2 Output load Fig. 1 Notes: 1. Include scope and jig capacitance. 2. Test conditions as specified with output loading as shown in Fig. 1 unless otherwise noted. 3. Device is deselected as defined by the Truth Table. Output Load 1 DQ 50 30pF* VDDQ/2 * Distributed Test Jig Capacitance Rev: 2.14c 1/2004 19/39 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 1998, Giga Semiconductor, Inc. GS8161Z18(T/D)/GS8161Z32(D)/GS8161Z36(T/D) DC Electrical Characteristics Parameter Symbol Test Conditions Min Max Input Leakage Current (except mode pins) IIL VIN = 0 to VDD -1 uA 1 uA ZZ Input Current IIN1 VDD VIN VIH 0 V VIN VIH -1 uA -1 uA 1 uA 100 uA FT Input Current IIN2 VDD VIN VIL 0 V VIN VIL -100 uA -1 uA 1 uA 1 uA Output Leakage Current IOL Output Disable, VOUT = 0 to VDD -1 uA 1 uA Output High Voltage VOH2 IOH = -8 mA, VDDQ = 2.375 V 1.7 V -- Output High Voltage VOH3 IOH = -8 mA, VDDQ = 3.135 V 2.4 V -- Output Low Voltage VOL IOL = 8 mA -- 0.4 V Rev: 2.14c 1/2004 20/39 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 1998, Giga Semiconductor, Inc. Rev: 2.14c 1/2004 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. 21/39 -- Device Deselected; All other inputs VIH or VIL Deselect Current IDD 60 85 IDD Pipeline Flow Through 20 ISB 20 ISB Pipeline Flow Through 165 10 260 15 180 20 290 30 IDDQ IDD IDDQ IDD IDDQ IDD IDDQ IDD IDDQ IDD Flow Through Pipeline Flow Through Pipeline Flow Through 165 10 260 20 IDD IDDQ 180 20 IDD IDDQ Flow Through Pipeline 290 40 0 to 70C IDD IDDQ Symbol Pipeline Mode 65 90 30 30 175 10 270 15 190 20 300 30 175 10 270 20 190 20 300 40 -40 to 85C -250 60 80 20 20 155 10 235 15 170 20 265 30 155 10 235 20 170 20 265 35 65 85 30 30 165 10 245 15 180 20 275 30 165 10 245 20 180 20 275 35 -40 to 85C -225 0 to 70C Notes: 1. IDD and IDDQ apply to any combination of VDD3, VDD2, VDDQ3, and VDDQ2 operation. 2. All parameters listed are worst case scenario. -- ZZ VDD - 0.2 V (x18) (x36) (x18) (x36) Standby Current 2.5 V Operating Current Device Selected; All other inputs VIH or VIL Output open Device Selected; All other inputs VIH or VIL Output open Operating Current 3.3 V Test Conditions Parameter Operating Currents 50 75 20 20 150 10 215 15 165 15 240 25 150 10 215 15 165 15 240 30 0 to 70C 55 80 30 30 160 10 225 15 175 15 250 25 160 10 225 15 175 15 250 30 -40 to 85C -200 50 64 20 20 140 10 185 10 155 15 205 20 140 10 185 15 155 15 205 25 0 to 70C 55 70 30 30 150 10 195 10 165 15 215 20 150 10 195 15 165 15 215 25 -40 to 85C -166 50 60 20 20 135 10 170 10 150 15 190 20 135 10 170 15 150 15 190 25 0 to 70C 55 65 30 30 145 10 180 10 160 15 200 20 145 10 180 15 160 15 200 25 -40 to 85C -150 45 50 20 20 125 10 155 10 140 10 170 15 125 10 155 10 140 10 170 20 0 to 70C 50 55 30 30 135 10 165 10 150 10 180 15 135 10 165 10 150 10 180 20 -40 to 85C -133 mA mA mA mA mA mA mA mA mA mA mA mA Unit GS8161Z18(T/D)/GS8161Z32(D)/GS8161Z36(T/D) (c) 1998, Giga Semiconductor, Inc. GS8161Z18(T/D)/GS8161Z32(D)/GS8161Z36(T/D) AC Electrical Characteristics Pipeline Flow Through Parameter Symbol Clock Cycle Time -250 -225 -200 -166 -150 -133 Unit Min Max Min Max Min Max Min Max Min Max Min Max tKC 4.0 -- 4.4 -- 5.0 -- 6.0 -- 6.7 -- 7.5 -- ns Clock to Output Valid tKQ -- 2.5 -- 2.7 -- 3.0 -- 3.4 -- 3.8 -- 4.0 ns Clock to Output Invalid tKQX 1.5 -- 1.5 -- 1.5 -- 1.5 -- 1.5 -- 1.5 -- ns Clock to Output in Low-Z tLZ1 1.5 -- 1.5 -- 1.5 -- 1.5 -- 1.5 -- 1.5 -- ns Setup time tS 1.2 -- 1.3 -- 1.4 -- 1.5 -- 1.5 -- 1.5 -- ns Hold time tH 0.2 -- 0.3 -- 0.4 -- 0.5 -- 0.5 -- 0.5 -- ns Clock Cycle Time tKC 5.5 -- 6.0 -- 6.5 -- 7.0 -- 7.5 -- 8.5 -- ns Clock to Output Valid tKQ -- 5.5 -- 6.0 -- 6.5 -- 7.0 -- 7.5 -- 8.5 ns Clock to Output Invalid tKQX 3.0 -- 3.0 -- 3.0 -- 3.0 -- 3.0 -- 3.0 -- ns 1 Clock to Output in Low-Z tLZ 3.0 -- 3.0 -- 3.0 -- 3.0 -- 3.0 -- 3.0 -- ns Setup time tS 1.5 -- 1.5 -- 1.5 -- 1.5 -- 1.5 -- 1.5 -- ns Hold time tH 0.5 -- 0.5 -- 0.5 -- 0.5 -- 0.5 -- 0.5 -- ns Clock HIGH Time tKH 1.3 -- 1.3 -- 1.3 -- 1.3 -- 1.5 -- 1.7 -- ns Clock LOW Time tKL 1.5 -- 1.5 -- 1.5 -- 1.5 -- 1.7 -- 2 -- ns Clock to Output in High-Z tHZ1 1.5 2.3 1.5 2.5 1.5 3.0 1.5 3.0 1.5 3.0 1.5 3.0 ns G to Output Valid tOE -- 2.3 -- 2.5 -- 3.2 -- 3.5 -- 3.8 -- 4.0 ns G to output in Low-Z tOLZ1 0 -- 0 -- 0 -- 0 -- 0 -- 0 -- ns G to output in High-Z tOHZ1 -- 2.3 -- 2.5 -- 3.0 -- 3.0 -- 3.0 -- 3.0 ns ZZ setup time tZZS2 5 -- 5 -- 5 -- 5 -- 5 -- 5 -- ns ZZ hold time tZZH2 1 -- 1 -- 1 -- 1 -- 1 -- 1 -- ns ZZ recovery tZZR 20 -- 20 -- 20 -- 20 -- 20 -- 20 -- ns Notes: 1. These parameters are sampled and are not 100% tested. 2. ZZ is an asynchronous signal. However, in order to be recognized on any given clock cycle, ZZ must meet the specified setup and hold times as specified above. Rev: 2.14c 1/2004 22/39 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 1998, Giga Semiconductor, Inc. Rev: 2.14c 1/2004 G DQa-DQd Ao-An Bn W ADV E* CKE CK tS A tS tS tS tS tS tH tH tH tH tH tH Write A B Write B D(A) tS tKH tH D(B) C tKL Write B+1 tKC Read C D(B+1) tLZ tKQ Cont Q(C) D tOHZ Read D Pipeline Mode Timing E tOE Write E tHZ tOLZ Q(D) F G Write G D(E) tKQX Read F Q(F) D(G) Deselect GS8161Z18(T/D)/GS8161Z32(D)/GS8161Z36(T/D) Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. 23/39 (c) 1998, Giga Semiconductor, Inc. Rev: 2.14c 1/2004 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. 24/39 G DQ Ao-An Bn W ADV E* CKE CK tS A tS tS tS tS tS D(A) tS B tH Write B D(B) tKH tKQ tLZ tKC Read C D(B+1) C tKL Write B+1 *Note: E = High (False) if E1 = 1 or E2 = 0 or E3 = 1 tH tH tH tH tH tH Write A Q(C) tOHZ Cont D tOLZ tOE Read D Flow Through Mode Timing tHZ Q(D) E tKQX Write E tKQ tLZ D(E) F Read F Q(F) G tKQX Write G D(G) GS8161Z18(T/D)/GS8161Z32(D)/GS8161Z36(T/D) (c) 1998, Giga Semiconductor, Inc. GS8161Z18(T/D)/GS8161Z32(D)/GS8161Z36(T/D) JTAG Port Operation Overview The JTAG Port on this RAM operates in a manner that is compliant with IEEE Standard 1149.1-1990, a serial boundary scan interface standard (commonly referred to as JTAG). The JTAG Port input interface levels scale with VDD. The JTAG output drivers are powered by VDDQ. Disabling the JTAG Port It is possible to use this device without utilizing the JTAG port. The port is reset at power-up and will remain inactive unless clocked. TCK, TDI, and TMS are designed with internal pull-up circuits.To assure normal operation of the RAM with the JTAG Port unused, TCK, TDI, and TMS may be left floating or tied to either VDD or VSS. TDO should be left unconnected. JTAG Pin Descriptions Pin Pin Name I/O Description TCK Test Clock In Clocks all TAP events. All inputs are captured on the rising edge of TCK and all outputs propagate from the falling edge of TCK. TMS Test Mode Select In The TMS input is sampled on the rising edge of TCK. This is the command input for the TAP controller state machine. An undriven TMS input will produce the same result as a logic one input level. In The TDI input is sampled on the rising edge of TCK. This is the input side of the serial registers placed between TDI and TDO. The register placed between TDI and TDO is determined by the state of the TAP Controller state machine and the instruction that is currently loaded in the TAP Instruction Register (refer to the TAP Controller State Diagram). An undriven TDI pin will produce the same result as a logic one input level. TDI Test Data In TDO Test Data Out Output that is active depending on the state of the TAP state machine. Output changes in Out response to the falling edge of TCK. This is the output side of the serial registers placed between TDI and TDO. Note: This device does not have a TRST (TAP Reset) pin. TRST is optional in IEEE 1149.1. The Test-Logic-Reset state is entered while TMS is held high for five rising edges of TCK. The TAP Controller is also reset automaticly at power-up. JTAG Port Registers Overview The various JTAG registers, refered to as Test Access Port orTAP Registers, are selected (one at a time) via the sequences of 1s and 0s applied to TMS as TCK is strobed. Each of the TAP Registers is a serial shift register that captures serial input data on the rising edge of TCK and pushes serial data out on the next falling edge of TCK. When a register is selected, it is placed between the TDI and TDO pins. Instruction Register The Instruction Register holds the instructions that are executed by the TAP controller when it is moved into the Run, Test/Idle, or the various data register states. Instructions are 3 bits long. The Instruction Register can be loaded when it is placed between the TDI and TDO pins. The Instruction Register is automatically preloaded with the IDCODE instruction at power-up or whenever the controller is placed in Test-Logic-Reset state. Bypass Register The Bypass Register is a single bit register that can be placed between TDI and TDO. It allows serial test data to be passed through the RAM's JTAG Port to another device in the scan chain with as little delay as possible. Rev: 2.14c 1/2004 25/39 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 1998, Giga Semiconductor, Inc. GS8161Z18(T/D)/GS8161Z32(D)/GS8161Z36(T/D) Boundary Scan Register The Boundary Scan Register is a collection of flip flops that can be preset by the logic level found on the RAM's input or I/O pins. The flip flops are then daisy chained together so the levels found can be shifted serially out of the JTAG Port's TDO pin. The Boundary Scan Register also includes a number of place holder flip flops (always set to a logic 1). The relationship between the device pins and the bits in the Boundary Scan Register is described in the Scan Order Table following. The Boundary Scan Register, under the control of the TAP Controller, is loaded with the contents of the RAMs I/O ring when the controller is in Capture-DR state and then is placed between the TDI and TDO pins when the controller is moved to Shift-DR state. SAMPLE-Z, SAMPLE/PRELOAD and EXTEST instructions can be used to activate the Boundary Scan Register. JTAG TAP Block Diagram * * * * * * Boundary Scan Register * * 0 Bypass Register 0 108 * 1 * * 2 1 0 Instruction Register TDI TDO ID Code Register 31 30 29 * * * * 2 1 0 Control Signals TMS TCK Test Access Port (TAP) Controller Identification (ID) Register The ID Register is a 32-bit register that is loaded with a device and vendor specific 32-bit code when the controller is put in Capture-DR state with the IDCODE command loaded in the Instruction Register. The code is loaded from a 32-bit on-chip ROM. It describes various attributes of the RAM as indicated below. The register is then placed between the TDI and TDO pins when the controller is moved into Shift-DR state. Bit 0 in the register is the LSB and the first to reach TDO when shifting begins. ID Register Contents TBD for this part. Rev: 2.14c 1/2004 26/39 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 1998, Giga Semiconductor, Inc. GS8161Z18(T/D)/GS8161Z32(D)/GS8161Z36(T/D) Die Revision Code GSI Technology JEDEC Vendor ID Code I/O Configuration Not Used Presence Register ID Register Contents Bit # 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 x36 X X X X 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 1 1 0 1 1 0 0 1 1 x18 X X X X 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 0 0 0 0 1 1 0 1 1 0 0 1 1 Tap Controller Instruction Set Overview There are two classes of instructions defined in the Standard 1149.1-1990; the standard (Public) instructions, and device specific (Private) instructions. Some Public instructions are mandatory for 1149.1 compliance. Optional Public instructions must be implemented in prescribed ways. The TAP on this device may be used to monitor all input and I/O pads, and can be used to load address, data or control signals into the RAM or to preload the I/O buffers. When the TAP controller is placed in Capture-IR state the two least significant bits of the instruction register are loaded with 01. When the controller is moved to the Shift-IR state the Instruction Register is placed between TDI and TDO. In this state the desired instruction is serially loaded through the TDI input (while the previous contents are shifted out at TDO). For all instructions, the TAP executes newly loaded instructions only when the controller is moved to Update-IR state. The TAP instruction set for this device is listed in the following table. Rev: 2.14c 1/2004 27/39 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 1998, Giga Semiconductor, Inc. GS8161Z18(T/D)/GS8161Z32(D)/GS8161Z36(T/D) JTAG Tap Controller State Diagram 1 0 Test Logic Reset 0 Run Test Idle 1 Select DR 1 Select IR 0 0 1 1 Capture DR Capture IR 0 0 Shift DR 1 1 Shift IR 0 1 1 Exit1 DR 0 Exit1 IR 0 0 Pause DR 1 Exit2 DR 1 Update DR 1 1 0 0 Pause IR 1 Exit2 IR 0 1 0 0 Update IR 1 0 Instruction Descriptions BYPASS When the BYPASS instruction is loaded in the Instruction Register the Bypass Register is placed between TDI and TDO. This occurs when the TAP controller is moved to the Shift-DR state. This allows the board level scan path to be shortened to facilitate testing of other devices in the scan path. SAMPLE/PRELOAD SAMPLE/PRELOAD is a Standard 1149.1 mandatory public instruction. When the SAMPLE / PRELOAD instruction is loaded in the Instruction Register, moving the TAP controller into the Capture-DR state loads the data in the RAMs input and I/O buffers into the Boundary Scan Register. Boundary Scan Register locations are not associated with an input or I/O pin, and are loaded with the default state identified in the Boundary Scan Chain table at the end of this section of the datasheet. Because the RAM clock is independent from the TAP Clock (TCK) it is possible for the TAP to attempt to capture the I/O ring contents while the input buffers are in transition (i.e. in a metastable state). Although allowing the TAP to sample metastable inputs will not harm the device, repeatable results cannot be expected. RAM input signals must be stabilized for long enough to meet the TAPs input data capture set-up plus hold time (tTS plus tTH). The RAMs clock inputs need not be paused for any other TAP operation except capturing the I/O ring contents into the Boundary Scan Register. Moving the controller to Shift-DR state then places the boundary scan register between the TDI and TDO pins. Rev: 2.14c 1/2004 28/39 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 1998, Giga Semiconductor, Inc. GS8161Z18(T/D)/GS8161Z32(D)/GS8161Z36(T/D) EXTEST EXTEST is an IEEE 1149.1 mandatory public instruction. It is to be executed whenever the instruction register is loaded with all logic 0s. The EXTEST command does not block or override the RAM's input pins; therefore, the RAM's internal state is still determined by its input pins. Typically, the Boundary Scan Register is loaded with the desired pattern of data with the SAMPLE/PRELOAD command. Then the EXTEST command is used to output the Boundary Scan Register's contents, in parallel, on the RAM's data output drivers on the falling edge of TCK when the controller is in the Update-IR state. Alternately, the Boundary Scan Register may be loaded in parallel using the EXTEST command. When the EXTEST instruction is selected, the sate of all the RAM's input and I/O pins, as well as the default values at Scan Register locations not associated with a pin, are transferred in parallel into the Boundary Scan Register on the rising edge of TCK in the Capture-DR state, the RAM's output pins drive out the value of the Boundary Scan Register location with which each output pin is associated. IDCODE The IDCODE instruction causes the ID ROM to be loaded into the ID register when the controller is in Capture-DR mode and places the ID register between the TDI and TDO pins in Shift-DR mode. The IDCODE instruction is the default instruction loaded in at power up and any time the controller is placed in the Test-Logic-Reset state. SAMPLE-Z If the SAMPLE-Z instruction is loaded in the instruction register, all RAM outputs are forced to an inactive drive state (highZ) and the Boundary Scan Register is connected between TDI and TDO when the TAP controller is moved to the Shift-DR state. RFU These instructions are Reserved for Future Use. In this device they replicate the BYPASS instruction. JTAG TAP Instruction Set Summary Instruction Code Description EXTEST 000 Places the Boundary Scan Register between TDI and TDO. 1 IDCODE 001 Preloads ID Register and places it between TDI and TDO. 1, 2 SAMPLE-Z 010 Captures I/O ring contents. Places the Boundary Scan Register between TDI and TDO. Forces all RAM output drivers to High-Z. 1 RFU 011 Do not use this instruction; Reserved for Future Use. Replicates BYPASS instruction. Places Bypass Register between TDI and TDO. 1 SAMPLE/ PRELOAD 100 Captures I/O ring contents. Places the Boundary Scan Register between TDI and TDO. 1 GSI 101 GSI private instruction. 1 RFU 110 Do not use this instruction; Reserved for Future Use. Replicates BYPASS instruction. Places Bypass Register between TDI and TDO. 1 BYPASS 111 Places Bypass Register between TDI and TDO. Notes: 1. Instruction codes expressed in binary, MSB on left, LSB on right. 2. Default instruction automatically loaded at power-up and in test-logic-reset state. Rev: 2.14c 1/2004 29/39 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. Notes 1 (c) 1998, Giga Semiconductor, Inc. GS8161Z18(T/D)/GS8161Z32(D)/GS8161Z36(T/D) JTAG Port Recommended Operating Conditions and DC Characteristics Parameter Symbol Min. Max. Unit Notes 3.3 V Test Port Input High Voltage VIHJ3 2.0 VDD3 +0.3 V 1 3.3 V Test Port Input Low Voltage VILJ3 -0.3 0.8 V 1 2.5 V Test Port Input High Voltage VIHJ2 0.6 * VDD2 VDD2 +0.3 V 1 2.5 V Test Port Input Low Voltage VILJ2 -0.3 0.3 * VDD2 V 1 TMS, TCK and TDI Input Leakage Current IINHJ -300 1 uA 2 TMS, TCK and TDI Input Leakage Current IINLJ -1 100 uA 3 TDO Output Leakage Current IOLJ -1 1 uA 4 Test Port Output High Voltage VOHJ 1.7 -- V 5, 6 Test Port Output Low Voltage VOLJ -- 0.4 V 5, 7 Test Port Output CMOS High VOHJC VDDQ - 100 mV -- V 5, 8 Test Port Output CMOS Low VOLJC -- 100 mV V 5, 9 Notes: 1. Input Under/overshoot voltage must be -2 V > Vi < VDDn +2 V not to exceed 4.6 V maximum, with a pulse width not to exceed 20% tTKC. 2. VILJ VIN VDDn 3. 0 V VIN VILJn 4. Output Disable, VOUT = 0 to VDDn 5. The TDO output driver is served by the VDDQ supply. 6. IOHJ = -4 mA 7. IOLJ = + 4 mA 8. IOHJC = -100 uA 9. IOHJC = +100 uA Rev: 2.14c 1/2004 30/39 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 1998, Giga Semiconductor, Inc. GS8161Z18(T/D)/GS8161Z32(D)/GS8161Z36(T/D) JTAG Port AC Test Conditions Parameter Conditions Input high level VDD - 0.2 V Input low level 0.2 V Input slew rate 1 V/ns Input reference level VDDQ/2 Output reference level VDDQ/2 JTAG Port AC Test Load DQ 50 30pF* VDDQ/2 * Distributed Test Jig Capacitance Notes: 1. Include scope and jig capacitance. 2. Test conditions as as shown unless otherwise noted. JTAG Port Timing Diagram tTKC tTKH tTKL TCK tTH tTS TDI tTH tTS TMS tTKQ TDO tTH tTS Parallel SRAM input Rev: 2.14c 1/2004 31/39 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 1998, Giga Semiconductor, Inc. GS8161Z18(T/D)/GS8161Z32(D)/GS8161Z36(T/D) JTAG Port AC Electrical Characteristics Parameter Symbol Min Max Unit TCK Cycle Time tTKC 50 -- ns TCK Low to TDO Valid tTKQ -- 20 ns TCK High Pulse Width tTKH 20 -- ns TCK Low Pulse Width tTKL 20 -- ns TDI & TMS Set Up Time tTS 10 -- ns TDI & TMS Hold Time tTH 10 -- ns Boundary Scan (BSDL Files) For information regarding the Boundary Scan Chain, or to obtain BSDL files for this part, please contact our Applications Engineering Department at: apps@gsitechnology.com. Rev: 2.14c 1/2004 32/39 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 1998, Giga Semiconductor, Inc. GS8161Z18(T/D)/GS8161Z32(D)/GS8161Z36(T/D) TQFP Package Drawing (Package T) L A1 Standoff 0.05 0.10 0.15 A2 Body Thickness 1.35 1.40 1.45 b Lead Width 0.20 0.30 0.40 c Lead Thickness 0.09 -- 0.20 D Terminal Dimension 21.9 22.0 22.1 D1 Package Body 19.9 20.0 20.1 E Terminal Dimension 15.9 16.0 16.1 E1 Package Body 13.9 14.0 14.1 e Lead Pitch -- 0.65 -- L Foot Length 0.45 0.60 0.75 L1 Lead Length -- 1.00 -- Y Coplanarity Lead Angle L1 Min. Nom. Max c e D D1 Description Pin 1 Symbol b A1 A2 0.10 Y E1 E 0 -- 7 Notes: 1. All dimensions are in millimeters (mm). 2. Package width and length do not include mold protrusion. Thermal Characteristics Package 100 TQFP (T) Rev: 2.14c 1/2004 Junction to Ambient (Ja) (C/W) 0 m/s 1 m/s 2 m/s 20.4 19.1 17.2 33/39 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. Junction to Case (Jc) (C/W) 3.6 (c) 1998, Giga Semiconductor, Inc. GS8161Z18(T/D)/GS8161Z32(D)/GS8161Z36(T/D) Package Dimensions--165-Bump FPBGA (Package D) A1 CORNER TOP VIEW BOTTOM VIEW O0.10 M C O0.25 M C A B O0.40~0.50 (165x) 1 2 3 4 5 6 7 8 9 10 11 A1 CORNER 11 10 9 8 7 6 5 4 3 2 1 A B C D E F G H J K L M N P R 1.0 14.0 150.07 1.0 A B C D E F G H J K L M N P R A 1.0 1.0 0.15 C SEATING PLANE C 130.07 B 0.20(4x) 0.25~0.40 1.20 MAX. (0.26) 0.450.05 0.25 C 10.0 Thermal Characteristics Package 165 BGA (D) Rev: 2.14c 1/2004 Junction to Ambient (Ja) (C/W) 0 m/s 1 m/s 2 m/s 20.5 17.2 16.1 Junction to Case (Jc) (C/W) 34/39 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. 3.4 (c) 1998, Giga Semiconductor, Inc. GS8161Z18(T/D)/GS8161Z32(D)/GS8161Z36(T/D) Ordering Information--GSI NBT Synchronous SRAM Org Part Number1 Type Package Speed2 (MHz/ns) TA3 1M x 18 GS8161Z18T-250 NBT Pipeline/Flow Through TQFP 250/5.5 C 1M x 18 GS8161Z18T-225 NBT Pipeline/Flow Through TQFP 225/6 C 1M x 18 GS8161Z18T-200 NBT Pipeline/Flow Through TQFP 200/6.5 C 1M x 18 GS8161Z18T-166 NBT Pipeline/Flow Through TQFP 166/7 C 1M x 18 GS8161Z18T-150 NBT Pipeline/Flow Through TQFP 150/7.5 C 1M x 18 GS8161Z18T-133 NBT Pipeline/Flow Through TQFP 133/8.5 C 512K x 36 GS8161Z36T-250 NBT Pipeline/Flow Through TQFP 250/5.5 C 512K x 36 GS8161Z36T-225 NBT Pipeline/Flow Through TQFP 225/6 C 512K x 36 GS8161Z36T-200 NBT Pipeline/Flow Through TQFP 200/6.5 C 512K x 36 GS8161Z36T-166 NBT Pipeline/Flow Through TQFP 166/7 C 512K x 36 GS8161Z36T-150 NBT Pipeline/Flow Through TQFP 150/7.5 C 512K x 36 GS8161Z36T-133 NBT Pipeline/Flow Through TQFP 133/8.5 C 1M x 18 GS8161Z18T-250I NBT Pipeline/Flow Through TQFP 250/5.5 I 1M x 18 GS8161Z18T-225I NBT Pipeline/Flow Through TQFP 225/6 I 1M x 18 GS8161Z18T-200I NBT Pipeline/Flow Through TQFP 200/6.5 I 1M x 18 GS8161Z18T-166I NBT Pipeline/Flow Through TQFP 166/7 I 1M x 18 GS8161Z18T-150I NBT Pipeline/Flow Through TQFP 150/7.5 I 1M x 18 GS8161Z18T-133I NBT Pipeline/Flow Through TQFP 133/8.5 I 512K x 36 GS8161Z36T-250I NBT Pipeline/Flow Through TQFP 250/5.5 I 512K x 36 GS8161Z36T-225I NBT Pipeline/Flow Through TQFP 225/6 I 512K x 36 GS8161Z36T-200I NBT Pipeline/Flow Through TQFP 200/6.5 I 512K x 36 GS8161Z36T-166I NBT Pipeline/Flow Through TQFP 166/7 I 512K x 36 GS8161Z36T-150I NBT Pipeline/Flow Through TQFP 150/7.5 I 512K x 36 GS8161Z36T-133I NBT Pipeline/Flow Through TQFP 133/8.5 I 1M x 18 GS8161Z18D-250 NBT Pipeline/Flow Through 165 BGA 250/5.5 C 1M x 18 GS8161Z18D-225 NBT Pipeline/Flow Through 165 BGA 225/6 C 1M x 18 GS8161Z18D-200 NBT Pipeline/Flow Through 165 BGA 200/6.5 C 1M x 18 GS8161Z18D-166 NBT Pipeline/Flow Through 165 BGA 166/7 C Status 1M x 18 GS8161Z18D-150 NBT Pipeline/Flow Through 165 BGA 150/7.5 C Notes: 1. Customers requiring delivery in Tape and Reel should add the character "T" to the end of the part number. Example: GS816Z36-166IT. 2. The speed column indicates the cycle frequency (MHz) of the device in Pipeline mode and the latency (ns) in Flow Through mode. Each device is Pipeline/Flow through mode-selectable by the user . 3. TA = C = Commercial Temperature Range. TA = I = Industrial Temperature Range. 4. GSI offers other versions this type of device in many different configurations and with a variety of different features, only some of which are covered in this data sheet. See the GSI Technology web site (www.gsitechnology.com) for a complete listing of current offerings Rev: 2.14c 1/2004 35/39 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 1998, Giga Semiconductor, Inc. GS8161Z18(T/D)/GS8161Z32(D)/GS8161Z36(T/D) Ordering Information--GSI NBT Synchronous SRAM (Continued) Org Part Number1 Type Package Speed2 (MHz/ns) TA3 1M x 18 GS8161Z18D-133 NBT Pipeline/Flow Through 165 BGA 133/8.5 C 512K x 32 GS8161Z32D-250 NBT Pipeline/Flow Through 165 BGA 250/5.5 C 512K x 32 GS8161Z32D-225 NBT Pipeline/Flow Through 165 BGA 225/6 C 512K x 32 GS8161Z32D-200 NBT Pipeline/Flow Through 165 BGA 200/6.5 C 512K x 32 GS8161Z32D-166 NBT Pipeline/Flow Through 165 BGA 166/7 C 512K x 32 GS8161Z32D-150 NBT Pipeline/Flow Through 165 BGA 150/7.5 C 512K x 32 GS8161Z32D-133 NBT Pipeline/Flow Through 165 BGA 133/8.5 C 512K x 36 GS8161Z36D-250 NBT Pipeline/Flow Through 165 BGA 250/5.5 C 512K x 36 GS8161Z36D-225 NBT Pipeline/Flow Through 165 BGA 225/6 C 512K x 36 GS8161Z36D-200 NBT Pipeline/Flow Through 165 BGA 200/6.5 C 512K x 36 GS8161Z36D-166 NBT Pipeline/Flow Through 165 BGA 166/7 C 512K x 36 GS8161Z36D-150 NBT Pipeline/Flow Through 165 BGA 150/7.5 C 512K x 36 GS8161Z36D-133 NBT Pipeline/Flow Through 165 BGA 133/8.5 C 1M x 18 GS8161Z18D-250I NBT Pipeline/Flow Through 165 BGA 250/5.5 I 1M x 18 GS8161Z18D-225I NBT Pipeline/Flow Through 165 BGA 225/6 I 1M x 18 GS8161Z18D-200I NBT Pipeline/Flow Through 165 BGA 200/6.5 I 1M x 18 GS8161Z18D-166I NBT Pipeline/Flow Through 165 BGA 166/7 I 1M x 18 GS8161Z18D-150I NBT Pipeline/Flow Through 165 BGA 150/7.5 I 1M x 18 GS8161Z18D-133I NBT Pipeline/Flow Through 165 BGA 133/8.5 I 512K x 32 GS8161Z32D-250I NBT Pipeline/Flow Through 165 BGA 250/5.5 I Status 512K x 32 GS8161Z32D-225I NBT Pipeline/Flow Through 165 BGA 225/6 I Notes: 1. Customers requiring delivery in Tape and Reel should add the character "T" to the end of the part number. Example: GS816Z36-166IT. 2. The speed column indicates the cycle frequency (MHz) of the device in Pipeline mode and the latency (ns) in Flow Through mode. Each device is Pipeline/Flow through mode-selectable by the user . 3. TA = C = Commercial Temperature Range. TA = I = Industrial Temperature Range. 4. GSI offers other versions this type of device in many different configurations and with a variety of different features, only some of which are covered in this data sheet. See the GSI Technology web site (www.gsitechnology.com) for a complete listing of current offerings Rev: 2.14c 1/2004 36/39 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 1998, Giga Semiconductor, Inc. GS8161Z18(T/D)/GS8161Z32(D)/GS8161Z36(T/D) Ordering Information--GSI NBT Synchronous SRAM (Continued) Org Part Number1 Type Package Speed2 (MHz/ns) TA3 512K x 32 GS8161Z32D-200I NBT Pipeline/Flow Through 165 BGA 200/6.5 I 512K x 32 GS8161Z32D-166I NBT Pipeline/Flow Through 165 BGA 166/7 I 512K x 32 GS8161Z32D-150I NBT Pipeline/Flow Through 165 BGA 150/7.5 I 512K x 32 GS8161Z32D-133I NBT Pipeline/Flow Through 165 BGA 133/8.5 I 512K x 36 GS8161Z36D-250I NBT Pipeline/Flow Through 165 BGA 250/5.5 I 512K x 36 GS8161Z36D-225I NBT Pipeline/Flow Through 165 BGA 225/6 I 512K x 36 GS8161Z36D-200I NBT Pipeline/Flow Through 165 BGA 200/6.5 I 512K x 36 GS8161Z36D-166I NBT Pipeline/Flow Through 165 BGA 166/7 I 512K x 36 GS8161Z36D-150I NBT Pipeline/Flow Through 165 BGA 150/7.5 I Status 512K x 36 GS8161Z36D-133I NBT Pipeline/Flow Through 165 BGA 133/8.5 I Notes: 1. Customers requiring delivery in Tape and Reel should add the character "T" to the end of the part number. Example: GS816Z36-166IT. 2. The speed column indicates the cycle frequency (MHz) of the device in Pipeline mode and the latency (ns) in Flow Through mode. Each device is Pipeline/Flow through mode-selectable by the user . 3. TA = C = Commercial Temperature Range. TA = I = Industrial Temperature Range. 4. GSI offers other versions this type of device in many different configurations and with a variety of different features, only some of which are covered in this data sheet. See the GSI Technology web site (www.gsitechnology.com) for a complete listing of current offerings Rev: 2.14c 1/2004 37/39 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 1998, Giga Semiconductor, Inc. GS8161Z18(T/D)/GS8161Z32(D)/GS8161Z36(T/D) 18Mb Sync SRAM Data Sheet Revision History DS/DateRev. Code: Old; New Types of Changes Format or Content GS18/36 1.00 9/ 1999A;GS18/362.0012/ 1999B Content GS18/362.00 12/ 1999BGS18/362.01 1/2000C Format Page;Revisions;Reason * Converted from 0.25u 3.3V process to 0.18u 2.5V process. Master File Rev B * Added x72 Pinout. * Added new GSI Logo * Front page; Features - changed 2.5V I/O supply to 2.5V or3.3V I/O supply; Completeness * Absolute Maximum Ratings; Changed VDDQ - Value: From: .05 to VDD : to : -.05 to 3.6; Completeness. * Recommended Operating Conditions;Changed: I/O Supply Voltage- Max. from VDD to 3.6; Input High Voltage- Max. from VDD +0.3 to 3.6; Same page - took out Note 1;Completeness * Electrical Characteristics - Added second Output High Voltage line to table; completeness. * Note: There was not a Rev 2.02 for the 8160Z or the 8161Z. GS18/362.0 1/2000DGS18/ 362.03 2/2000E GS18/362.03 2/2000E; 8161Z18_r2_04 Content * Pin 14 removed from VSS in pin description table. * ADV changed to pin 85 in pin description table. 8161Z18_r2_04; 8161Z18_r2_05 Content * Changed the value of ZZ recovery in the AC Electrical Characteristics table on page 18 from 20 ns to 100 ns 8161Z18_r2_05; 8161Z18_r2_06 Content/Format * Added 225 MHz speed bin * Updated page 1 table, AC Characteristics table, and Operating Currents table * Updated format to comply with Technical Publications standards * Updated Capitance table--removed Input row and updated Output row to I/O 8161Z18_r2_06; 8161Z18_r2_07 Content * Updated Features list on page 1 * Completely reworked table on page 1 * Updated Mode Pin Functions on page 12 Content * Added 3.3 V references to entire document * Updated Operating Conditions table * Updated JTAG Operating Conditions table * Updated Boundary Scan Chain table * Updated Opearting Currents table and added note * Updated table on page 1; added power numbers Content * Updated Pin Description table * Updated DQ on page 21 * Updated DQ on page 23 * Updated Operating Currrents table * Updated table on page 1; updated power numbers * Updated Recommended Operating Conditions table (added VDDQ references) 8161Z18_r2_07; 8161Z18_r2_08 8161Z18_r2_08; 8161Z18_r2_09 Rev: 2.14c 1/2004 38/39 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 1998, Giga Semiconductor, Inc. GS8161Z18(T/D)/GS8161Z32(D)/GS8161Z36(T/D) 18Mb Sync SRAM Data Sheet Revision History DS/DateRev. Code: Old; New Types of Changes Format or Content Page;Revisions;Reason Content * Updated table on page 1 * Created recommended operating conditions tables on pages 15 and 16 * Updated AC Electrical Characteristics table * Updated Ordering Information for 225 MHz part (changed from 7ns to 6.5 ns) * Updated BSR table (2 and 3 changed to X (value undefined)) * Added 250 MHz speed bin * Deleted 180 MHz speed bin 8161Z18_r2_10; 8161Z18_r2_11 Content * Updated AC Characteristics table * Updated FT power numbers * Updated Mb references from 16Mb to 18Mb * Removed ByteSafe references * Changed DP and QE pins to NC * Updated ZZ recovery time diagram * Updated AC Test Conditions table and removed Output Load 2 diagram 8161Z18_r2_11; 8161Z18_r2_12 Content * Removed Preliminary banner * Removed BSR table * Removed pin locations from pin description table 8161Z18_r2_12; 8161Z18_r2_13 Content * Removed erroneous references to parity check * Added 165 BGA parts for x18 and x36; add x32 165 part * Update Abs Max table 8161Z18_r2_09; 8161Z18_r2_10 8161Z18_r2_13; 8161Z18_r2_14 Rev: 2.14c 1/2004 Content/Format * Added missing JTAG pin descriptions to TQFP pin description table * Updated Synchronous Truth Table * Removed A and DQ numbers from pinouts * Updated timing diagrams * Added commercial "D" parts to ordering information table * Format updated 39/39 Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com. (c) 1998, Giga Semiconductor, Inc.