www.fairchildsemi.com FAN4822 ZVS Average Current PFC Controller Features General Description * Average current sensing, continuous boost, leading edge PFC for low total harmonic distortion and near unity power factor * Built-in ZVS switch control with fast response for high efficiency at high power levels * Average line voltage compensation with brownout control * Current fed gain modulator improves noise immunity and provides universal input operation * Overvoltage comparator eliminates output "runaway" due to load removal * UVLO, current limit, and soft-start * Precision 1.3% reference The FAN4822 is a PFC controller designed specifically for high power applications. The controller contains all of the functions necessary to implement an average current boost PFC converter, along with a Zero Voltage Switch (ZVS) controller to reduce diode recovery and MOSFET turn-on losses. The average current boost PFC circuit provides high power factor (>98%) and low Total Harmonic Distortion (THD). Built-in safety features include undervoltage lockout, overvoltage protection, peak current limiting, and input voltage brownout protection. The ZVS control section drives an external ZVS MOSFET which, combined with a diode and inductor, soft switches the boost regulator. This technique reduces diode reverse recovery and MOSFET switching losses to reduce EMI and maximize efficiency. Block Diagram VEAO FB - 14 2.5V IAC 4 + 1 8 2 GND FB R+ + GAIN MODULATOR + VCC OVP 12 VCCZ 13.5V IEA 2.7V - + - - VRMS 5 IEAO VEA S Q I LIMIT R- -1V ISENSE + R - 3 PFC OUT 11 RTCT 6 OSC S Q R Q VCCZ REF 13 ZV SENSE 7 ZVS OUT REF 10 + -- S Q R Q PWR GND 9 REV. 1.0.1 8/10/01 FAN4822 PRODUCT SPECIFICATION Pin Configuration FAN4822 FAN4822 14-Pin DIP (P14) 16-Pin SOIC (S16W) VEAO 1 14 FB VEAO 1 16 FB IEAO 2 13 REF IEAO 2 15 REF ISENSE 3 12 VCC ISENSE 3 14 VCC IAC 4 11 PFC OUT IAC 4 13 PFC OUT VRMS 5 10 ZVS OUT VRMS 5 12 ZVS OUT RTCT 6 9 PWR GND RTCT 6 11 PWR GND ZV SENSE 7 8 GND ZV SENSE 7 10 GND N/C 8 9 N/C TOP VIEW TOP VIEW Pin Description (Pin numbers is parentheses are for 16-pin package) Pin Name Function 1 (1) VEAO Transconductance voltage error amplifier output. 2 (2) IEAO Transconductance current error amplifier output. 3 (3) ISENSE 4 (4) IAC 5 (5) VRMS Input for RMS line voltage compensation. 6 (6) RTCT Connection for oscillator frequency setting components. 7 (7) ZV SENSE 8 (10) GND 9 (11) PWR GND Return for the PFC and ZVS driver outputs. 10 (12) ZVS OUT ZVS MOSFET driver output. 11 (13) PFC OUT 12 (14) VCC Shunt-regulated supply voltage. 13 (15) REF Buffered output for the internal 7.5V reference. 14 (16) FB Transconductance voltage error amplifier input. Current sense input to the PFC current limit comparator. PFC gain modulator reference input. Input to the high speed zero voltage crossing comparator. Analog signal ground. PFC MOSFET driver output. Absolute Maximum Ratings Absolute maximum ratings are those values beyond which the device could be permanently damaged. Absolute maximum ratings are stress ratings only and functional device operation is not implied. Parameter Min Max Unit 55 mA 500 mA 7 V 150 C 150 C Lead Temperature (Soldering, 10 sec) 150 C Thermal Resistance (JA) Plastic DIP Plastic SOIC 80 110 C/W C/W Shunt Regulator Current (ICC) Peak Driver Output Current Analog Inputs -0.3 Junction Temperature Storage Temperature Range 2 -65 REV. 1.0.1 8/10/01 PRODUCT SPECIFICATION FAN4822 Operating Conditions Temperature Range Min. Max. Units FAN4822IX -40 85 C Electrical Characteristics Unless otherwise specified, RT = 52.3k, CT = 470pF, TA = Operating Temperature Range (Note 1) Parameter Conditions Min. Typ. Max. Units 7 V Voltage Error Amplifier Transconductance 0 50 70 120 Feedback Reference Voltage VEAO = VFB 2.4 2.5 2.6 V Open Loop Gain 60 75 dB 60 75 dB PSRR VNON-INV = VINV, VEAO = 3.75V Input Voltage Range VCCZ - 3V < VCC < VCCZ - 0.5V Output Low 0.65 Output High 1 V 6.0 6.7 V Source Current VIN = 0.5V, VOUT = 6V -40 -80 A Sink Current VIN = 0.5V, VOUT = 1.5V 40 80 mA Current Error Amplifier Transconductance -1.5 VNON-INV = VINV, IEAO = 3.75V 130 Input Offset Voltage Open Loop Gain PSRR VCCZ - 3V < VCC < VCCZ - 0.5V 2 195 310 3 15 mV 60 75 dB 60 75 dB Output Low 0.65 Output High V Input Voltage Range 1 V 6.0 6.7 V Source Current VIN = 0.5V, VOUT = 6V -30 -80 A Sink Current VIN = 0.5V, VOUT = 1.5V 40 80 A Threshold Voltage 2.6 2.7 2.8 V Hysteresis 80 120 150 mV -0.8 -1.0 -1.15 V 150 300 ns 50 ns 7.5 7.65 V OVP Comparator ISENSE Comparator Threshold Voltage Delay to Output ZV Sense Comparator Propagation Delay Threshold Voltage Input Capacitance REV. 1.0.1 8/10/01 100mV Overdrive 7.35 6 pF 3 FAN4822 PRODUCT SPECIFICATION Electrical Characteristics (Continued) Unless otherwise specified, RT = 52.3k, CT = 470pF, TA = Operating Temperature Range (Note 1) Parameter Conditions Min. Typ. Max. IIAC = 100mA, VVRMS = 0V, VFB = 0V 0.36 0.51 0.66 IIAC = 50mA, VVRMS = 1.2V, VFB = 0V 1.20 1.72 2.24 IIAC = 100A, VVRMS = 1.8V, VFB = 0V 0.55 0.78 1.01 IIAC = 100A, VVRMS = 3.3V, VFB = 0V 0.14 0.20 0.26 Units Gain Modulator Gain (Note 2) Bandwidth IIAC = 250A Output Voltage VFB = 0V, VVRMS = 1.15V, IIAC = 250A 10 MHz 0.72 0.8 0.9 V 74 80 87 kHz Oscillator Initial Accuracy TA = 25C Voltage Stability VCCZ - 3V < VCC < VCCZ - 0.5V Temperature Stability Total Variation Line, temperature 1 % 2 % 72 Ramp Valley to Peak Voltage 89 kHz 2.5 V Dead Time 100 300 450 ns CT Discharge Current 4.5 7.5 9.5 mA 7.4 7.5 7.6 V Reference Output Voltage TA = 25C, IREF = 1mA Line Regulation VCCZ - 3V < VCC < VCCZ - 0.5V 2 10 mV Load Regulation 1mA < IREF, < 20mA 2 15 mV Temperature Stability 0.4 Total Variation Line, load, and temperature Long Term Stability Tj = 125C, 1000 hours Short Circuit Current VCC < VCCZ - 0.5V, VREF = 0V 7.35 -15 % 7.65 V 5 25 mV -40 -100 mA 0 % PFC Comparator Minimum Duty Cycle VIEAO > 6.7V Maximum Duty Cycle VIEAO < 1.2V 90 95 % MOSFET Driver Outputs Output Low Voltage Output High Voltage Output Rise/Fall Time IOUT = -20mA 0.4 1.0 V IOUT = -100mA 1.5 3.5 V IOUT = -10mA, VCC = 8V 0.8 1.5 V IOUT = 20mA 9.5 10.3 V IOUT = 100mA 9 10.3 V 40 ns CL = 1000pF Undervoltage Lockout Threshold Voltage Hysteresis 4 VCCZ - 0.9 VCCZ - 0.6 VCCZ - 0.2 V 2.4 2.9 3.45 V REV. 1.0.1 8/10/01 PRODUCT SPECIFICATION FAN4822 Electrical Characteristics (Continued) Unless otherwise specified, RT = 52.3k, CT = 470pF, TA = Operating Temperature Range (Note 1) Parameter Conditions Min. Typ. Max. Units Supply Shunt Voltage (VCCZ) ICC =25mA Load Regulation 25mA < ICC < 55mA Total Variation Load and temperature Start-up Current VCC < 12.3V Operating Current VCC = VCCZ - 0.5V 12.8 13.5 14.2 V 150 300 mV 14.6 V 0.7 1.1 mA 22 28 mA 12.4 Notes 1. Limits are guaranteed by 100% testing, sampling, or correlation with worst-case test conditions. 2. Gain = K x 5.3 V; K = (IGAINMOD - IOFFSET) x IAC x (VEAO - 1.5)-1. REV. 1.0.1 8/10/01 5 FAN4822 PRODUCT SPECIFICATION Functional Description bined parasitic capacitance of D1 and Q1 (or optional ZVS capacitor CZVS). At t3, the voltage across Q1 is sufficiently low that the controller turns Q2 off and Q1 on. Q1 then behaves as an ordinary PFC switch, storing energy in the boost inductor L1. The energy stored in L2 is completely discharged into the boost capacitor via D2 during the Q1 offtime and the value of L2 must be selected for discontinuousmode operation. Switching losses of wide input voltage range PFC boost converters increase dramatically as power levels increase above 200 watts. The use of zero-voltage switching (ZVS) techniques improves the efficiency of high power PFCs by significantly reducing the turn-on losses of the boost MOSFET. ZVS is accomplished by using a second, smaller MOSFET, together with a storage element (inductor) to convert the turn-on losses of the boost MOSFET into useful output power. Component Selection Q1 Turn-Off Because the FAN4822 uses leading edge modulation, the PFC MOSFET (Q1) is always turned off at the end of each oscillator ramp cycle. For proper operation, the internal ZVS flip-flop must be reset every cycle during the oscillator discharge time. This is done by automatically resetting the ZVS comparator a short time after the drain voltage of the main Q has reached zero (refer to Figure 1 sense circuit). This sense circuit terminates the ZVS on time by sensing the main Q drain voltage reaching zero. It is then reset by way of a resistor pull-up to VCC (R6). The advantage of this circuit is that the ZVS comparator is not reset at the main Q turn off which occurs at the end of the clock cycle. This avoids the potential for improper reset of the internal ZVS flip-flop. The basic function of the FAN4822 is to provide a power factor corrected, regulated DC bus voltage using continuous, average current-mode control. Like Micro Linear's family of PFC/PWM controllers, the FAN4822 employs leading-edge pulse width modulation to reduce system noise and permit frequency synchronization to a trailing edge PWM stage for the highest possible DC bus voltage bandwidth. For minimization of switching losses, circuitry has been incorporated to control the switching of the ZVS FET. Theory of Operation Figure 1 shows a simplified schematic of the output and control sections of a high power PFC circuit. Figure 2 shows the relationship of various waveforms in the circuit. Q1 functions as the main switching FET and Q2 provides the ZVS action. During each cycle, Q2 turns on before Q1, diverting the current in L1 away from D1 into L2. The current in L2 increases linearly until at t2 it equals the current through L1. When these currents are equal, L1 ceases discharging current and is now charged through L2 and Q2. At time t2, the drain voltage of Q1 begins to fall. The shape of the voltage waveform is sinusoidal due to the interaction of L2 and the com- Another concern is the proper operation of the ZVS comparator during discontinuous mode operation (DCM), which will occur at the cusps of the rectified AC waveform and at light loads. Due to the nature of the voltage seen at the drain of the main boost Q during DCM operation, the ZVS comparator can be fooled into forcing the ZVS Q on for the entire period. By adding a circuit which limits the maximum on time of the ZVS Q, this problem can be avoided. Q3 in Figure 1 provides this function. L1 D1 + C1 VREF 13 VREF L2 FAN4822 CZVS(OPT) 12 VCC D2 Q1 R3 22k R5 220 R6 22k PFC OUT 11 C4 330pF C2 Q2 7 ZV SENSE 8 GND C3 33pF R4 51k R1 ZVS OUT 10 PWR GND 9 MAX ZVS ON TIME LIMIT R2 Q3 C5 Figure 1. Simplified PFC/ZVS Schematic. 6 REV. 1.0.1 8/10/01 PRODUCT SPECIFICATION FAN4822 Q1 Turn-On The turn-on event consists of the time it takes for the current through L2 to ramp to the L1 current plus the resonant event of L2 and the ZVS capacitor. The total event should occur in a minimum of 350-450ns, but can be longer at the risk of increasing the total harmonic distortion. Setting these times equal should minimize conducted and radiated emissions. t Q1 ( OFF ) = t IL2 + t RES = 400ns A. SYSTEM CLOCK (INTERNAL) (1) B. RTCT Where IL2 is equal to IL1. The value of L2 is calculated to remain in discontinuousmode: V BUS x V RMS ( MIN ) x t IL2 L2 = ---------------------------------------------------------------2 x P OUT C. ZVS GATE (Q2) (2) The resonant event occurs in 1/4 of a full sinusoidal cycle. For example, when a 1/4 cycle occurs in 200ns, the frequency is 1.25MHz. D. VDS (Q2) 1 1 f RES = ----------------------------------- = --------------------x 4 t RES 2 L2 x C ZVS (3) Rearranging and solving for L2: 4 x t RES 2 L2 = -------------------------2 x C ZVS E. PFC GATE (Q1) (4) The resonant capacitor (CZVS) value is found by setting equations 2 and 4 equal to each other and solving for CZVS. 4 x t RES 2 x 2 x P OUT C ZVS = ---------------------------------------------------------------------------2 x V BUS x V RMS ( MIN ) x t IL2 F. VDS (Q1) (5) Application Figure 3 displays a typical application circuit for a 500W ZVS PFC supply. Full design details are covered in application note 33, FAN4822 Power Factor Correction With Zero Voltage Resonant Switching. G. IL2 t1 t3 t2 Figure 2. Timing Diagrams REV. 1.0.1 8/10/01 7 8 R25 51k R24 22k NEUTRAL C19 330pF 50V R16 8.25k 1% R27 220 D10 UF4005 C14 0.47F 250VAC LINE 8AMP 250VAC F1 C20 2.2nF 50V GBU6G D13 1N5401 R26 22k C13 100pF 50V C18 33pF 50V R15 16.2k 1% R23 402k 1% R13 402k 1% R19 10k C11 68nF 50V C12 2.2nF 50V D7 1N5401 R18 0.0732 5W 1% B1 C6 0.47F 16V ISENSE IEAO C22 100pF ZVS OUT PFC OUT VCC REF FB R4 10k 1N4148 R29 10k GND PWR GND ZV SENSE RTCT VRMS IAC C4 0.1F 50V FAN4822 VEAO Q3 2N7000 7 6 5 4 3 2 1 R17 220k C7 0.68F 50V R14 100k 1% R22 453k 1% R12 453k 1% 8 9 10 11 12 13 14 D5 1N4747A Q1 FQA24N50 L1 420uH @ 10A n = 57 C5 1F 50V D8 1N5819 D9 1N5819 C8 2.2F 50V C2 470pF 1600V D6 1N4747A R3 10 L2 8.5m @ 14A FESI6JT D1 4 3 2 1 R1 3.3k 3W IN B NC OUT B VS OUT A VS RTN IN A NC TC4427 R6 10k Q2 FQP6N50 D3 MUR460 R7 47 C9 1F 50V C15 1500F 25V 5 6 7 8 C1 330F 450V D4 UF4005 C21 0.1F 200V MUR860 D2 C17 1F 50V C3 1000pF 50V 400VDC C10 1F 50V D12 EGP20A D11 EGP20A R21 39k 2W 400VDC RTN R11 2.37k 1% R2 10 C16 1F 50V + R20 93.1k 1% R9 93.1k 1% R8 93.1k 1% R10 102k 1% L1 n = 2.5 R5 39k 2W FAN4822 PRODUCT SPECIFICATION Figure 3. FAN4822 Schematic. REV. 1.0.1 8/10/01 PRODUCT SPECIFICATION FAN4822 Mechanical Dimensions inches (millimeters) Package: P14 14-Pin PDIP 0.740 - 0.760 (18.79 - 19.31) 14 0.240 - 0.260 0.295 - 0.325 (6.09 - 6.61) (7.49 - 8.25) PIN 1 ID 0.070 MIN (1.77 MIN) (4 PLACES) 1 0.050 - 0.065 0.100 BSC (1.27 - 1.65) (2.54 BSC) 0.015 MIN (0.38 MIN) 0.170 MAX (4.32 MAX) 0.016 - 0.022 SEATING PLANE (0.40 - 0.56) 0.125 MIN (3.18 MIN) 0 - 15 0.008 - 0.012 (0.20 - 0.31) Package: S16W 16-Pin Wide SOIC 0.400 - 0.414 (10.16 - 10.52) 16 0.291 - 0.301 0.398 - 0.412 (7.39 - 7.65) (10.11 - 10.47) PIN 1 ID 1 0.024 - 0.034 (0.61 - 0.86) (4 PLACES) 0.050 BSC (1.27 BSC) 0.095 - 0.107 (2.41 - 2.72) 0 - 8 0.090 - 0.094 (2.28 - 2.39) REV. 1.0.1 8/10/01 0.012 - 0.020 (0.30 - 0.51) SEATING PLANE 0.005 - 0.013 (0.13 - 0.33) 0.022 - 0.042 (0.56 - 1.07) 0.009 - 0.013 (0.22 - 0.33) 9 FAN4822 PRODUCT SPECIFICATION Ordering Information Part Number FAN4822IN FAN4822IM PFC/PWM Frequency Package -40C to 85C -40C to 85C 14-Pin PDIP (P14) 16-Pin Wide SOIC (S16W) DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. LIFE SUPPORT POLICY FAIRCHILD'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. www.fairchildsemi.com 8/10/01 0.0m 003 Stock#DS30004803 2001 Fairchild Semiconductor Corporation