POE-D11-00-E-07 CERAMIC DISC CAPACITOR SAFETY RECOGNIZED, AC SERIES PRODUCT: Ver : 7 CERAMIC DISC CAPACITOR SAFETY RECOGNIZED TYPE: AC SERIES CUSTOMER: DOC. NO.: POE-D11-00-E-07 Ver.: 7 APPROVED BY CUSTOMER VENDOR WALSIN TECHNOLOGY CORPORATION 566-1, KAO SHI ROAD,YANG-MEI TAO-YUAN, TAIWAN PAN OVERSEAS (GUANGZHOU) ELECTRONIC CO.,LTD. NO.277,HONG MING ROAD,EASTERN SECTION, GUANG ZHOU ECONOMIC AND TECHNOLOGY DEVELOPMENT ZONE,CHINA MAKER PAN OVERSEAS (GUANGZHOU) ELECTRONIC CO.,LTD. NO.277,HONG MING ROAD,EASTERN SECTION, GUANG ZHOU ECONOMIC AND TECHNOLOGY DEVELOPMENT ZONE,CHINA Page: 1 / 20 POE-D11-00-E-07 CERAMIC DISC CAPACITOR SAFETY RECOGNIZED, AC SERIES Ver : 7 Page: 2 / 20 Record of change Date Version 2008.6.3 1 1. D23-00-E-01(before) 2008.8.22 2 2008.12.12 3 2009.7.16 4 1 Complete lead code 2. Add last SAP code " H" for halogen and Pb free , epoxy resin.. 1.Complete the 13th to 17th codes of SAP P/N. 2. Page layout adjustment. 1 Change PSA & POE logo to Walsin & POE logo. 2.Complete Marking statement. 3. Revised standard NO. of SEV, SEMKO, FIMKO, NEMKO, DEMKO and KEMA. Revised recognized NO. of FIMKO, NEMKO, DEMKO ,KEMA and CQC. 4. Downsize Description page POE-D11-00-E-01(1st edition) 20 3 4 9 11 6 YP0AC101K080** YP0AC101K060 ** YP0AC102K100** YP0AC102K080** YV0AC152M080** YV0AC152M060** 2009.9.14 5 1. "Protrusion length": "+0.5 to-1.0" revised to "2.0max (Or the end of lead wire may be inside the tape.)" 9 2009.12.24 6 10 11 14 2011/1/13 7 1. Marking 2. Correct recognized No 3. Revised the Figure of impulse voltage test(Item 7.3.14) according to the standard IEC 60384-14 ed.3 1. Review SAP P/N about diameter code: YP0AC151K080* YP0AC151K060* YP0AC221K080* YP0AC221K060* YP0AC331K080* YP0AC331K060* YP0AC561K080* YP0AC561K070* YP0AC681K090* YP0AC681K070* YP0AC821K100* YP0AC821K080* YU0AC152M100* YU0AC152M080* 2. Delete "AT" taping type. 3. Add test item "Temperature Cycle ". 4. Add item 10 "Drawing of internal structure and material list" 6 4,5,8,9 15 20 POE-D11-00-E-07 CERAMIC DISC CAPACITOR SAFETY RECOGNIZED, AC SERIES Ver : 7 Page: 3 / 20 Table of Contents No. Item Page 1 Part number for SAP system 4/20 2 Mechanical 5/20 3 Part numbering/T.C/Capacitance/ Tolerance/Diameter 6/20~7/20 4 Taping Format 8/20~9/20 5 10/20 6 Marking Scope 11/20 7 Specification and test method 12/20~15/20 8 Packing specification Notices 16/20 17/20~19/20 Drawing of Internal Structure and material list 20/20 9 10 POE-D11-00-E-07 CERAMIC DISC CAPACITOR SAFETY RECOGNIZED, AC SERIES Ver : 7 Page: 4 / 20 1. Part number for SAP system (Ex.) YV 0AC 472 M 100 L 20 C 7 B Temperature characteristic (identified code) CODE CH(NP0) SL YP (Y5P) YV(Y5V) YU (Y5U) Cap. Change 060PPM/ -1000~+350PPM/ (+20~+85) 10% -80% ~ +30% -55% to +20% TYPE (identified by 3-figure code)0AC = AC TYPE (X1/Y2) Capacitance (identified by 3-figure code)EX.221=220pF Capacitance tolerance (identified by code)C:0.25pF,D:0.5pF,J:5%,K:10%,M:20% Nominal body diameter dimension (identified by 3-figure code) Lead StyleRefer to "2. Mechanical". Packing mode and lead length (identified by 2-figure code) Taping Code AF AM Bulk Code 3E 04 4E 20 Description Ammo box and product pitch15.0 mm Ammo box and product pitch25.4 mm Description Lead length 3.5mm Lead length 4.0mm Lead length 4.5mm Lead length20.0mm Length tolerance Code Description A 0.5 mm (only for kink lead type) 1.0 mm Min. Taping special purpose B C D Pitch Code Description 7 0 7.51 mm 101 mm Epoxy Resin Code Code Description B Pb free, Epoxy Resin H Halogen and Pb free , epoxy resin. POE-D11-00-E-07 CERAMIC DISC CAPACITOR SAFETY RECOGNIZED, AC SERIES Ver : 7 Page: 5 / 20 2. Mechanical EncapsulationEpoxy resin, flammability UL94 V-0 Available lead code(unit: mm) Lead type Lead styleL SAP P/N (13-17)digits Old P/N (Ref. to Pitch (F) "3.1 old P/N") Lead Type B L20C7 L7 7.5 1.0 20 min. L20C0 L0 10 1.0 20 min. BAFD7 L7F BAMD7 L7M BAMD0 L0M L03B7 L4EB7 7.5 1.0 7.5 1.0 L03B0 S7 S7 P16 S0 7.5 1.0 10 1.0 3.0 1.0 4.5 1.0 5.0 1.0 3.0 1.0 L4EB0 S0 10 1.0 4.5 1.0 A 10 1.0 5.0 1.0 D3EA7 D04A7 D3EA0 D04A0 DAFD7 DAMD7 DAMD0 X3EA7 X04A7 X05B7 X3EA0 X04A0 X05B0 XAFD7 XAMD7 XAMD0 D2 D7 D3 D0 D7F D7M D0M Q2 X7 X2 Q3 X0 X3 X7F X7M X0M 7.5 1.0 7.5 1.0 10 1.0 10 1.0 3.5 0.5 4.0 0.5 3.5 0.5 4.0 0.5 H3EA7 H2A 7.51.0 3.50.5 mm H3EA0 H3A 10.01.0 3.50.5 mm HAMD7 H7M Refer to "4. Taping HAMD0 H0M format" Bulk Straight long lead Lead styleL Type L Straight short lead L05B7 L05B0 Lead styleD Type D Vertical kink lead Lead styleX Type X Outside kink lead Lead styleH Type H Lead Configuration Length (L) Type L Straight long lead Lead styleB Packing Refer to "4. Taping format" Refer to "4. Taping format" 7.5 1.0 7.5 1.0 7.5 1.0 10 1.0 10 1.0 10 1.0 3.5 0.5 4.0 0.5 5.0 1.0 3.5 0.5 4.0 0.5 5.0 1.0 Refer to "4. Taping format" Tap. Ammo Bulk Bulk Tap. Ammo Bulk Tap. Ammo Bulk Inside kink lead Tap. Ammo * Lead diameter d: 0.60 +0.1/-0.05 * e (Coating extension on leads): 3.0mmMax for straight lead lead style; Not exceed the kink for kink lead. POE-D11-00-E-07 CERAMIC DISC CAPACITOR SAFETY RECOGNIZED, AC SERIES Ver : 7 Page: 6 / 20 3. Part numbering/T.C/Capacitance/ Tolerance/Diameter POE Part. No. T.C. SAP P/N CH0AC***C060* CH0AC***D060* CH0AC***J060* CH0AC***J070* CH0AC***J080* CH0AC390J090* CH0AC470J100* SL0AC***J060* SL0AC***J070* SL0AC820J080* SL0AC101J090* YP0AC101K060* YP0AC151K060* YP0AC221K060* YP0AC331K060* YP0AC471K060* YP0AC561K070* YP0AC681K070* YP0AC821K080* YP0AC102K080* YU0AC102M060* YU0AC152M080* YU0AC222M080* YU0AC332M100* YU0AC392M120* YU0AC472M120* YV0AC102M060* YV0AC152M060* YV0AC222M060* YV0AC332M080* YV0AC392M100* YV0AC472M100* YV0AC682M120* YV0AC103M140* Capacitance Old P/N (Refer to 3.1 Old P/N) AC06CH***C* 2, 3,4, 5(pF) AC06CH***D* 6,7,8,9,10(pF) 12,15(pF) AC06CH***J* CH AC07CH***J* (NP0) 18,20,22, 24(pF) 27,30,33,(pF) AC08CH***J* 36,39(pF) AC09CH390J* 47(pF) AC10CH470J* 10,12,15,18,20,22,2 4,27,30,33, AC06SL***J* 36,39,47,50,51(pF) SL 56,62, 68,75(pF) AC07SL***J* 82pF AC08SL820J* 100pF AC09SL101J* AC06B101K* 100 pF AC06B151K* 150 pF AC06B221K* 220 pF AC06B331K* 330 pF AC06B471K* Y5P 470 pF AC07B561K* 560pF AC07B681K* 680 pF AC08B821K* 820 pF AC08B102K* 1000 pF AC06E102M* 1000 pF AC080E152M* 1500 pF AC08E222M* 2200 pF Y5U AC10E332M* 3300 pF AC12E392M* 3900 pF AC12E472M* 4700 pF AC06F102M* 1000 pF AC06F152M* 1500 pF AC06F222M* 2200 pF AC08F332M* 3300 pF Y5V AC11F392M* 3900 pF AC10F472M* 4700 pF AC12F682M* 6800 pF AC14F103M* 10000 pF Tolerance D (max) 0.25pF 0.5pF 5% 5% 5% 5% 5% 7.0 7.0 7.0 8.0 9.0 10.0 11.0 5% 7.0 5% 5% 5% 10% 10% 10% 10% 10% 10% 10% 10% 10% 20% 20% 20% 20% 20% 20% 20% 20% 20% 20% 20% 20% 20% 20% 8.0 9.0 10.0 7.0 7.0 7.0 7.0 7.0 8.0 8.0 9.0 9.0 7.0 9.0 9.0 11.0 13.0 13.0 7.0 7.0 7.0 9.0 11.0 11.0 13.0 15.0 Dimensions (unitmm) F T Taping (max) Bulk type type 7.51 (AFD7) or 101 (AMD0) 5.0 0.60 +0.10 - 0.05 7.51, 101 ** The minimum thickness of coating (reinforced insulation) is 0.4mm. Graph (ex.) d 7.51 (AFD7) or 101 (AMD0) 101 (AMD0) 7.51 (AFD7) or 101 (AMD0) 101 (AMD0) POE-D11-00-E-07 CERAMIC DISC CAPACITOR SAFETY RECOGNIZED, AC SERIES Ver : 7 Page: 7 / 20 3.1 Old P/N TPYE (1) (2) (3) (4) (1)Nominal body diameter dimension (2)Temperature characteristic (identified code): (5) (6) (7) (Ex.) 0 CH(NP0):060PPM/, SL: +350~-1000PPM/, B(Y5P):10%, E(Y5U):-55% ~ +20%, F(Y5V) :-80% ~ +30% (3)Capacitance (identified by 3-figure code) (4)Capacitance tolerance (identified by code): C:0.25pF,D:0.5pF,J:5%,K:10%,M:20% (5)Lead style (configuration) (identified by code) L: straight long lead S: straight short lead D: vertical kink lead X: outside kink lead B: inside kink lead (6)Lead Space: 7=7.5 1.0 mm 0=10 1.0 mm (7)Taping type or other code Code Pitch component F 15.0 mm M 25.4 mm No code BULK POE-D11-00-E-07 CERAMIC DISC CAPACITOR SAFETY RECOGNIZED, AC SERIES Ver : 7 Page: 8 / 20 4. Taping Format POE Part Number Item Pitch of component Pitch of sprocket Lead spacing Length from hole center to component center Length from hole center to lead Body diameter Deviation along tape, life or right Carrier tape width Position of sprocket hole Lead distance between the kink and center of sprocket hole Lead distance between the bottom of body and the center of sprocket hole Protrusion length Diameter of sprocket hole Lead diameter Total tape thickness Total thickness, tape and lead wire Deviation across tape Portion to cut in case of defect Hole-down tape width Hole-down tape distortion Coating extension on leads Body thickness *BAFD7 Symbol *DAFD7 *XAFD7 *BAMD7 *DAMD7 *HAMD7 *XAMD7 Dimensions (mm) Dimensions (mm) Dimensions (mm) *BAMD0 *DAMD0 *HAMD0 *XAMD0 Dimensions (mm) P P0 F 15.0 15.00.3 7.51.0 15.0 15.00.3 7.51.0 25.4 12.70.3 7.51.0 25.4 12.70.3 10.01.0 P2 7.51.5 7.51.5 12.71.5 12.7 1.5 P1 D S W W1 H0 3.751.0 3.751.0 8.951.0 7.71.5 See the "3. Part numbering/T.C/Capacitance/ Tolerance/Diameter" 02.0 18.0 +1/-0.5 9.00.5 18.0+2.0/-0 18.0+2.0/-0 18.0+2.0/-0 --(For: *DAMD7 / (For: *DAMD0 / *XAMD7) H D0 d t1 t2 h1/h2 L W0 W2 e T *HAMD0 / *XAMD0) 20.0+1.5/-1.0 (For: *BAMD7) 20.0+1.5/-1.0 (For: *BAMD0) 2.0max (Or the end of lead wire may be inside the tape.) 4.00.2 0.60 +0.1/-0.05 0.60.3 1.5 max. 20.0+1.5/-1.0 --- 2.0 max. 11.0 max. 11.5min 1.51.5 3.0 max for straight lead style; Not exceed the kink leads for kink lead. See the "3. Part numbering/T.C/Capacitance/ Tolerance/Diameter" POE-D11-00-E-07 CERAMIC DISC CAPACITOR SAFETY RECOGNIZED, AC SERIES Ver : 7 Page: 9 / 20 5.Marking 1.Type Designation AC 2.Nominal Capacitance 3-digit-system 3.Capacitance Tolerance 4.Company Name Code(Trade mark) C:0.25pF,D:0.5pF,J:5%,K:10%,M:20% 5.Manufactured Date Abbreviation ex. 6.Approved Monogram (1) VDE approval mark IEC 60384-14 3rd (2005). Class CodeX1400V~ Y2250V~ (2) UL approval mark (7) FIMKO approval mark (3) CSA approval mark (8) SEV approval mark (4) SEMKO approval mark (9) CQC approval mark (5) NEMKO approval mark (6) DEMKO approval mark Ex.: Two sides: One side: Marking by the stamp or laser. The marking can be printed on either one side or two side of coating body. "C01", Marked with code " _ " stand for Halogen and Pb freeNo marked with " _" stand for Pb free. POE-D11-00-E-07 CERAMIC DISC CAPACITOR SAFETY RECOGNIZED, AC SERIES Ver : 7 Page: 10 / 20 6. Scope THIS SPECIFICATION APPLIES TO CERAMIC INSULATED CAPACITORS DISK TYPE USED IN ELECTRONIC EQUIPMENT. 1. VDE/SEV/SEMKO/FIMKO/NEMKO/DEMKO/KEMA/UL/CSA recognized capacitor for Antenna coupling and AC line-by-pass.X1, Y2 Capacitor based on IEC 60384-14 3rd Edition (2005) "UL (AC250V), CSA recognized for across-the-line, line-by-pass" and antenna-isolation 2.Approval Standard and Recognized No. Safety Standard Standard No. Subclass w.v. Recognized No. UL UL 1414 X,Y 250VAC E146544 CSA C22.2 NO.1-04 X,Y 250VAC 1363528(LR 92203-1) VDE (ENEC) IEC60384-14 (ed. 3) 2005 X1 400VAC Y2 250VAC SEV IEC60384-14 (ed. 3) 2005 X1 400VAC Y2 250VAC SEMKO IEC60384-14 (ed. 3) 2005 X1 400VAC Y2 250VAC FIMKO IEC60384-14 (ed. 3) 2005 X1 400VAC Y2 250VAC NEMKO IEC60384-14 (ed. 3) 2005 X1 400VAC Y2 250VAC DEMKO IEC60384-14 (ed. 3) 2005 X1 400VAC Y2 250VAC KEMA IEC60384-14 (ed. 3) 2005 X1 400VAC Y2 250VAC CQC GB/T 14472-1998 X1 400VAC KTL K60384-14 Y2 X1 Y2 250VAC 400VAC 250VAC 40001829 09.1153 600117 NCS/FI 24754 P09210633 314839-01 2123149.01 CQC080010026519 SU03017-4001A SU03017-4002A POE-D11-00-E-07 CERAMIC DISC CAPACITOR SAFETY RECOGNIZED, AC SERIES Ver : 7 Page: 11 / 20 7. Specification and test method (1) Operating Temperature Range : -25 to +125C (-25 to +85C in case of the standard of UL / CSA) (2) Performance Tests Item 1 Dielectric Strength Specification Between lead wires No failure. Body Insulation No failure. 2 Insulation Resistance(I.R.) 10000M min. 3 Capacitance Within specified tolerance 4 Dissipation Factor(D.F.) or Q Char. Specification B,E D.F2.5% F D.F5.0% Q: 30pF&above:1000 CH,SL Below 30PF:400+20xC CH 060ppm/ -1000~+350 SL ppm/ (+20~+85) Pr-treatment Capacitor shall be stored at 852 for 1 hour. Then placed at room condition for 1()242 hours before measurement B Within 10% E Within % F Within -80 ~ +30% 6 Temperature Characteristic B&E&F: The capacitance shall be measured at 202with 1kHz20% and 5V(rms.) or less. CH&SL: The capacitance shall be measured at 25 with 1MHz20% and1.00.2Vrms The capacitance measurement shall be made at each step specified in table 1. (Table 1) Step Temperature 1 +202 2 -252 3 +202 4 +852 5 +202 Char. Capacitance Change 5 Testing Method The capacitors shall not be damage when AC2600V are applied between the lead wires for 60 sec. First the terminal of capacitor shall be connected together. Then a metal foil shall be closely wrapped around the body of the capacitor distance of about 3 to 4 mm from each terminal. Then the capacitor shall be inserted into a container filled with metal balls of about 1 mm diameter. Finally. AC2600V is applied for 60 sec. between the capacitor lead wires and metal balls. The insulation resistance shall be measured with 50050VDC with 605sec. of charging. Tensile With the termination in its normal position the specimen is held by its body in such a manner that the axis of the termination is Lead wire shall not cut off verticalthe tensile force of 10N shall be applied to the termination capacitor shall not be broken. in the direction of its axis and acting in a direction away from the body of the specimen. Bending With the termination in its normal position the specimen is held by its body in such a manner that the axis of the termination is verticala mass applying a force of 5N is then suspended from the end of the termination. The body of the specimen is then inclined Lead wire shall not cut off within a period of 2 to 3 sec., through an angle of approximately capacitor shall not be broken. 90 in the vertical plane and then resumed to its initial position over the same period of time; this operation constitutes one bend. One bend immediately followed by a second bend in the opposite direction. Robustness of Termination "room condition" temperature15~35, humidity45~75%,atmospheric pressure86~106kPa POE-D11-00-E-07 CERAMIC DISC CAPACITOR SAFETY RECOGNIZED, AC SERIES Item 7 Specification Solderability of leads Lead wire should be soldered with uniform coating on the axial direction over 3/4 of the circumferential direction. Ver : 7 Page: 12 / 20 Testing Method The lead wire of capacitor should be dipped into molten solder for 2 0.5 sec. The depth of immersion is up to about 1.5 to 2.0 mm from the root of lead wires. Temp. of solder Lead free solder ( Sn-3Ag -0.5Cu) 245 5 Appearance I.R. Dielectric Strength Soldering Effect (Non-Preheat) Capacitance No marked defect 1000M min. As shown in figure, the lead wires should be immersed in solder of 350 10 or 260 5 up to 1.5 to 2.0mm from the root of Terminal for 3.5 0.5 sec ( 10 1 sec for 260 5 ) Per Item 1. B,E,FWithin 10% SL,CH: Within2.5or 0.25pF,Whichever is large. Pre-treatment: Capacitor shall be stored at 852 for 1hour.then placed at 1 room condition for 242hours before initial measurements. Post-treatment: Capacitor shall be stored for 1 to 2hours at 1room condition. 8 Soldering Effect (On-Preheat) Appearance No marked defect. I.R. 1000M min. Dielectric Strength Per Item 1. Capacitance B,E,FWithin 10% SL,CH: Within2.5or 0.25pF,Whichever is large. First the capacitor should be stored at 120 + 0 / -5 for 60 + 0 / -5sec. Then, as in figure , the lead wires should be immersed solder of 260 + / -5 up to 1.5 to 2.0 mm from the root of terminal for 7.5 +0 / -1 sec. Pre-treatment: Capacitor shall be stored at 852 for 1hour.then placed at 1 room condition for 242hours before initial measurements. Post-treatment: Capacitor shall be stored for 1 to 2hours at 1room condition. POE-D11-00-E-07 CERAMIC DISC CAPACITOR SAFETY RECOGNIZED, AC SERIES Item Specification Appearance Humidity (Under Steady State) 9 Capacitance D.F. 10 Humidity Loading Q I.R. SL&CH: Less than 30pF=> Q 100+10xC/3 More than 30pF=> Q 200 Testing Method Set the capacitor for 50012 hours at 402, in 90 to 95% humidity. Then capacitor shall be stored for 1 to 2 hours at room condition. Apply the rated voltage for 50012 hours at 402, in 90 to 95% humidity and set it for 1 to 2 hours at room condition. B,E,F3000M min. SL&CH: 1000M min. No marked defect. Capacitance B,E,FWithin 20% SL&CH: Within3or 0.3pF,Whichever is large. Impulse Voltage: Each individual capacitor shall be subjected to a 5kv impulses for three times. After the capacitors are applied to life test. 3000M min. SL&CH: 1000M min. Life Dielectric Strength Per Item 1. The capacitor flame discharge as follows. Cycle Time 1~4 30 sec, max. 5 60 sec, max. 12 Page: 13 / 20 F7.5% max. Appearance I.R. 11 No marked defect. B Within 10% E Within 20% F Within 30% SL&CH: Within2.5or 0.25pF,Whichever is large. B,E5.0% max. Ver : 7 Fig. The specimen capacitors are placed in a circulating air oven for a period of 1000 hrs. The air in the oven is maintained at a temperature of 1252. Throughout the test. The capacitors are subjected to a 425Vrms alternating voltage of mains frequency. Except that once each hour the voltage id increased to 1000Vrms for 0.1sec. The capacitor shall subject to applied for 15 sec And then removed for 15 sec, until 5 cycles. Fig. Flame Test (Unit: mm) "room condition" temperature15~35, humidity45~75%,atmospheric pressure86~106kPa POE-D11-00-E-07 CERAMIC DISC CAPACITOR SAFETY RECOGNIZED, AC SERIES Item Specification Ver : 7 Page: 14 / 20 Testing Method The specimens shall be individually wrapped in at least one but more then two complete layers of cheesecloth. The specimens shall be subjected to 20 discharges. The interval between successive discharges shall be 5sec. The Uac shall be maintained for 2 min. after the last discharge. Fig. 13 14 Active Flammability Passive Flammability The cheesecloth shall not be on fire. The burning time shall not be exceeded the time 30 sec. The tissue paper shall not ignite. C1,21f10% C30.03f5% 10KV L1-41.5Mh20% 16A Rod core choke R 1002% Ct3f5% 10KV UacUr5% UrRated working voltage Cx Capacitor F Fuse, Rated 10A Ut Voltage applied to Ct The capacitor under test shall be held in the flame in the position, which best promotes burning. Each specimen shall only be exposed once to the flame. Time of exposure to flame30 sec Length of flame121 mm Gas burnerLength 35 mm min. Inside Dia.0.50.1 mm Outside Dia.0.9 mm max. Gas Butane gas Purity 95% min. Fig. POE-D11-00-E-07 CERAMIC DISC CAPACITOR SAFETY RECOGNIZED, AC SERIES Item Specification Appearance Char. Cap. Change SL, 5% CH 15 Temperature Cycle Ver : 7 B E,F 10% 20% I.R. Dielectric strength No marked defect DF / Q Q275+5/2C (C30pF) Q350 (C30pF) DF5.0% DF7.5% 3000M min. Per Item 1 Page: 15 / 20 Testing Method The capacitor should be subjected to 5 temperature cycles, then consecutively to 2 immersion cycles. <Temperature Cycle time: 5 cycle> Step Temperature() Time(min) 1 -25+0/-3 30 2 Room temp. 3 3 125+3/-0 30 4 Room temp. 3 Pre-treatment: Capacitor shall be stored at 852 for 1hour.then placed at 1room condition for 242hours. Post-treatment: Capacitor shall be stored for 1 to 2hours at 1room condition. "room condition" temperature15~35, humidity45~75%,atmospheric pressure86~106kPa POE-D11-00-E-07 CERAMIC DISC CAPACITOR SAFETY RECOGNIZED, AC SERIES Ver : 7 8. Packing specification 8.1 Packing size: Box Carton Bulk Ammo taping 8.2 Packing quantity: One bag One box One carton Bulk 500pcs 2000pcs 16000pcs Ammo taping (AF-Product pitch:15.0mm) -- 1000pcs 10000pcs Ammo taping (AM-Product pitch:25.4mm) -- 500pcs 5000pcs Page: 16 / 20 POE-D11-00-E-07 CERAMIC DISC CAPACITOR SAFETY RECOGNIZED, AC SERIES Ver : 7 Page: 17 / 20 9. Notices: 9.1 Caution(Rating): (1). Operating Voltage Be sure to maintain the Vp-p value of the applied voltage or the Vo-p which contains DC bias within the rated voltage range. When the voltage is started to apply to the circuit or it is stopped applying, the irregular voltage may be generated for a transit period because of resonance or switching. Be sure to use a capacitor within rated voltage containing this irregular voltage. (2). Operating Temperature and Self-generated Heat Keep the surface temperature of a capacitor below the upper limit of its rated operating temperature range. Be sure to take into account the heat generated by the capacitor itself. When the capacitor is used in a high-frequency current, pulse current or the like, it may have the self-generated heat due to dielectric-loss. Applied voltage should be the load such as self-generated heat is within 20 on the condition of atmosphere temperature 25. When measuring, use a thermocouple of small thermal capacity-K of 0.1mm and be in the condition where capacitor is not affected by radiant heat of other components and wind of surroundings. Excessive heat my lead to deterioration of the capacitor's characteristics and reliability. (3). Test condition for withstanding Voltage I. Test Equipment Test equipment for AC withstanding voltage shall be used with the performance of the wave similar to 50/60 Hz sine waves. If the distorted sine wave or over load exceeding the specified voltage value is applied, the defective may be caused. POE-D11-00-E-07 CERAMIC DISC CAPACITOR SAFETY RECOGNIZED, AC SERIES Ver : 7 Page: 18 / 20 II. Voltage Applied Method When the withstanding voltage is applied, capacitor's lead or terminal shall be firmly connected to the output of the withstanding voltage test equipment, and then the voltage shall be raised from near zero to the test voltage. If the test voltage without the raise from near zero voltage would be applied directly to capacitor, test voltage should be applied with the *zero cross. At the end of the test time, the test voltage shall be reduced to near zero, and then capacitor's lead or terminal shall be taken off the output of the withstanding voltage test equipment. If the test voltage without the raise from near zero voltage would be applied directly to capacitor, the surge voltage may arise, and therefore, the defective may be caused. ZERO CROSS is the point where voltage sine wave pass 0V.- See the right figure. (4). Fail-Safe When capacitor would be broken, failure may result in a short circuit. Be sure to provide an appropriate fail-safe function like a fuse on your product if failure would follow an electric shock, fire or fume. Failure to follow the above cautions may result, worst case, in a short circuit and cause fuming or partial dispersion when the product is used. 9.2 Caution (Storage and operating condition): Operating and storage environment The insulating coating of capacitors does not form a perfect seal; therefore, do not use or store capacitors in a corrosive atmosphere, especially where chloride gas, sulfide gas, acid, alkali, salt or the like are present. And avoid exposure to moisture. Before cleaning, bonding, or molding this product, verify that these processes do not affect product quality by testing the performance of a cleaned, bonded or molded product in the intended equipment. Store the capacitors where the temperature and relative humidity do not exceed -10 to 40 degrees centigrade and 15 to 85 %. Use capacitors within 6 months. "Failure to follow the above cautions may result, worst case, in a short circuit and cause fuming or partial dispersion when the product is used." 9.3 Caution (Soldering and Mounting): 9.3.1 Vibration and impact: Do not expose a capacitor or its leads to excessive shock or vibration during use. POE-D11-00-E-07 CERAMIC DISC CAPACITOR SAFETY RECOGNIZED, AC SERIES Ver : 7 Page: 19 / 20 9.3.2 Soldering: When soldering this product to a PCB/PWB, do not exceed the solder heat resistance specification of the capacitor. Subjecting this product to excessive heating could melt the internal junction solder and may result in thermal shocks that can crack the ceramic element. When soldering capacitor with a soldering iron, it should be performed in following conditions. Temperature of iron-tip: 400 degrees C. max. Soldering iron wattage: 50W max. Soldering time: 3.5 sec. max. 9.3.3 Cleaning (ultrasonic cleaning): To perform ultrasonic cleaning, observe the following conditions. Rinse bath capacity: Output of 20 watts per liter or less. Rinsing time: 5 min maximum. Do not vibrate the PCB/PWB directly. Excessive ultrasonic cleaning may lead to fatigue destruction of the lead wires. "Failure to follow the above cautions may result, worst case, in a short circuit and cause fuming or partial dispersion when the product is used." 9.4 Caution (Handling): Vibration and impact Do not expose a capacitor or its leads to excessive shock or vibration during use. "Failure to follow the above cautions may result, worst case, in a short circuit and cause fuming or partial dispersion when the product is used." POE-D11-00-E-07 CERAMIC DISC CAPACITOR SAFETY RECOGNIZED, AC SERIES Ver : 7 Page: 20 / 20 10. Drawing of internal structure and material list 1 2 3 4 5 Remarks No. Part name Material Model/Type 1.EF-150C 1 Insulation Coating Epoxy polymer 2.EF-150(HF) 3.PCE-210 2.PCE-300(HF) Component Epoxy resinPigment (Blue / UL 94 V-0 /) The minimum thickness of coating (reinforced insulation) is 0.4mm 2 Dielectric Element Ceramic CH/SL/Y5P/Y5U/Y5V BaTiO3 3 Solder Tin-silver Sn96.5-Ag3-Cu0.5 Sn96.5-Ag3-Cu0.5 4 Electrodes Ag 5 Leads wire Tinned copper clad steel wire 1.SP-160PL SilverGlass frit 2.SP-260PL 0.6+0.1/-0.05mm Substrate metal: Fe & Cu Surface plating: Sn 100%(3~7m)