DMF-50316NF-FW-1 - RF Micro Devices

DMF-50316NF-FW-1 (AA) No.99-0188 OPTREX CORPORATION Page 1/17

OPTREX

Type No.

*******

Aug 5, 1999

First Edition

Final Revisi on

Quality A ssurance Div.

Product i on Di v.

Checked by

Approved by

Product i on Di v.

Design Engi neeri ng Di v.

Prepared by

LCD Module Specification

ＤＭＦ－５０３１６ＮＦ－ＦＷ－１

ＤＭＦ－５０３１６ＮＦ－ＦＷ－１ＤＭＦ－５０３１６ＮＦ－ＦＷ－１

ＤＭＦ－５０３１６ＮＦ－ＦＷ－１

Table of Cont ent s

1. General Specifications .............................................................................2

2. Electrical Specifications...........................................................................3

3. Optical Specifications..............................................................................7

4. I/O Terminal.............................................................................................9

5. Test..........................................................................................................11

6. Appearance Standards............................................................................12

7. Code System of Production Lot ..........................................................15

8. Type Number..........................................................................................15

9. Applying Precautions.............................................................................15

10. Precautions Relating Product Handling................................................16

11. Warranty..................................................................................................17

Revision History

Rev. Date Page Comment

DMF-50316NF-FW-1 (AA) No.99-0188 OPTREX CORPORATION Page 2/17

OPTREX

1. General Specifications

Operating Temp . ： min. 0℃ ～ max. 50℃

Storage Temp. ： min. -20℃ ～ max. 60℃

Dot Pixels ： 240 (W) × 64 (H) dots

Dot Size ： 0.50 (W) × 0.50 (H) mm

Dot Pitch ： 0.53 (W) × 0.53 (H) mm

Viewing Area ： 132.0 (W) × 39.0 (H) mm

Outline Dimensions ： 180.0 (W) × 70.0 (H) × 14.0 max.* (D) mm

* Without CFL Cable

Weight ： 155g max.

LCD Type ： NTD-12222

( F-STN / Black &White-mode / Transmissive )

Viewing Angle ： 6:00

Control LSI ： T6963C-0101 (Produced by TOSHIBA)

Data Transfer ： 8-bit parallel da ta transfer

Backlight ： Cold Cathode Fluorescent Lamp (CFL) × 1

Additional Spec. ： (1) Nega/Posi Reverse Circuit

(2) Holder and PWB ground are connected by soldering.

Drawings ： Dimensional Outline UE-35433A

DMF-50316NF-FW-1 (AA) No.99-0188 OPTREX CORPORATION Page 3/17

OPTREX

2.Electrical Specifications

2.1.Absolute Maximum Ratings VSS=0V

Parameter Symbol Conditions Min. Max. Units

Supply Voltage

(Logic)

VCC-VSS － -0.3 7.0 V

Supply Voltage

(LCD Drive)

VCC-VEE － -0.3 30.0 V

Input Voltage VI － -0.3 VCC+0.3 V

2.2.DC Characteristics Ta=25℃, VSS=0V

Parameter Symbol Conditions Min. Typ. Max. Units

Supply Voltage

(Logic)

VCC-VSS － 4.5

－ 5.5 V

Supply Voltage

(LCD Drive)

VCC-VEE Shown in 3.1 V

High Level

Input Voltage

VIH V

CC=5.0V±10% VCC-2.2 － V

CC V

Low Level

Input Voltage

VIL V

CC=5.0V±10% 0 － 0.8 V

High Level

Output Voltage

VOH I

OH=-0.75mA VCC-0.3 － V

CC V

Low Level

Output Voltage

VOL I

OL=0.75mA 0

－ 0.3 V

Supply Current

ICC V

CC-VSS=5.0V － 9.0 20.0 mA

EE V

CC-VEE=13.3V － 3.0 10.0 mA

DMF-50316NF-FW-1 (AA) No.99-0188 OPTREX CORPORATION Page 4/17

OPTREX

2.3.AC Characteristics VCC=5.0V±10%

Parameter Symbol Min. Max. Units

C/D Setup Time tCDS 100

－ ns

C/D Hold Time tCDH 10

－ ns

CE, RD, WR Pulse Width tCE, tRD, tWR 80 － ns

Data Setup Time tDS 80

－ ns

Data Hold Time tDH 40

－ ns

Access Time tACC － 150 ns

Output Hold Time tOH 10 50 ns

(WRITE)

(READ)

RD, WR

D0～D7

C/D

D0～D7

tDS

tOH

tDH

tACC

tCE, tRD, tWR

tCDH

tCDS

DMF-50316NF-FW-1 (AA) No.99-0188 OPTREX CORPORATION Page 5/17

OPTREX

2.4.Power Supply ON/OFF Sequence

2.4.1.ON Sequence

2.4.2.OFF Sequence

2.4.3.Reset Sequence

Please maintain the above sequence when turning on and off the power supply of the module.

If VEE is supplied to the module while internal alternate signal for LCD driving (M) is unstable or

RESET is active, DC component will be supplied to the LCD panel. This may cause damage to

the LCD mod ule.

RESET

VCC

VEE

SIGNAL

T≧0

T≧0T≧0T≧50msT≧50ms

T>250μs

LEVEL

L Level

H Level

VCC

VEE

VCC

VSS

Power OffPower On Reset CancellationReset

T≧10 ms

VEE

VSS

VCC

VSS

VCC

VEE

VCC

0≦t

SIGNAL

LEVEL

VCC

(Without RESET Signal)

VEE

VSS

VCC

VSS

VCC

VEE

VCC

0≦t

SIGNAL

LEVEL

VCC (Without RESE T Signal)

DMF-50316NF-FW-1 (AA) No.99-0188 OPTREX CORPORATION Page 6/17

OPTREX

2.5.Lighting Specifications Ta=25℃

Parameter Symbol Conditions Min. Typ. Max. Units Notes

Lamp Voltage VL －－ 365 － Vrms 1

Lamp Current IL － 4.0 5.0 6.0 mArms 2

Starting Voltage VS － 450

－－ Vrms 3

Surface Luminance L IL=5.0mA 70 130 － cd/㎡ 4

Average Life TAL － 50000

－－ hrs 5

Note 1 : The voltage ( r.m.s. ) to maintain the electric discharge of the lamp. It is measured after lighting for

3 minutes .

Note 2 : The curre nt ( r.m.s. ) to flow through the lamp with the elec tric disc harge. It is meas ured after

lighting for 3 minutes.

Note 3 : T he voltage at starting the electric discharge when the voltage is increased gradually from 0V.

Note 4 : Surface Luminance is specified by the initial data of luminance measured at the center of display

surface after 20 minutes power on. ( All ON pattern )

Note 5 : CFL life is defined as the time for which the initial luminance is attenuated by 50% of the

luminance value. Average Life representes the time elapsed at the point of time when the residual

ratio becomes below 50% when plural lamps are lighted in comparison with the definition of life

mentioned above.

Conditions : Ta=25 ℃±5℃, I L=5.0mA, CXA-L10A( Produced by TDK ), Windless

Recommended Inverter : HIU-32 ( Produced by HARISON ) CXA-L10L ( Produced by TDK )

CFL Testin

Circuit

VS VL

DMF-50316NF-FW-1 (AA) No.99-0188 OPTREX CORPORATION Page 7/17

OPTREX

3.Optical Specifications

3.1.LCD Driving Voltage

Parameter Symbol Conditions Min. Typ. Max. Units

Recommended Ta= 0℃ －－ 16.1 V

LCD Driving Voltage VCC-VEE Ta=25℃ 12.4 13.3 14.2 V

Note 1 Ta=50℃ 11.4

－－ V

Note 1 : Voltage (Applied actual waveform to LCD Module) for the best contrast. The range of

minimum and maximum shows tolerance of the operating voltage. The specified contrast ratio and

response time are not guaranteed over the entire range.

3.2.Optical Characteristics Ta=25℃, 1/64 Duty, 1/9 Bias, VD=13.3V (Note 4), θ= 0 ﾟ, φ=－ﾟ

Parameter Symbol Conditions Min. Typ. Max. Units

Contrast Ratio Note 1 CR θ= 0 ﾟ, φ=－ﾟ－ 50 －

Viewing Angle Shown in 3.3

Response Rise

Note 2 TON －－ 220 330 ms

Time Decay Note 3 TOFF －－ 80 160 ms

Note 1 : Contrast ratio is definded as follows.

CR = LON / LOFF

LON : Luminance of the ON segments

LOFF : Luminance of the OFF segments

Note 2 : The time that the luminance level reaches 90% of the saturation level from 0% when ON

signal is applied.

Note 3 : The time that the luminance level reaches 10% of the saturation level from 100% when OFF

signal is applied.

Note 4 : Definition of Driving Vo ltage VD

^Assuming that the typical driving waveforms shown below are applied to the LCD Panel at

1/A Duty - 1/B Bias ( A : Duty Number, B : Bias Number ). Driving voltage VD is definded

as the voltage VO-P when the contrast ratio (CR=LON / LOFF) is at its maximum.

VO-P

1 / fF

(

B-2

)

×VO-P / B

1 /

(

fF×A

)

〈OFF SIGNAL〉

〈ON SIGNAL〉

DMF-50316NF-FW-1 (AA) No.99-0188 OPTREX CORPORATION Page 8/17

OPTREX

3.3.Definition of Viewing Angle and Optimum Viewing Area

･Point ● shows the point where contrast ratio is measured. : θ= 0 ﾟ, φ=－ﾟ

･Driving condition : 1/64 Duty, 1 /9 Bias, VD=13.3V, fF=70Hz

･Area shows typ. CR

≧2

3.4.System Block Diagram

270 ﾟ

0ﾟ

90 ﾟ

180 ﾟ

270 ﾟ

135 ﾟ

315 ﾟ

225 ﾟ

45 ﾟ

180 ﾟ

90 ﾟ

(φ= 0 ﾟ）

10 20 30 40 50

Halogen bulb

Computer

Rotation Table (θ,φ)

Temperature Chamber

LCD

Optical Fiber

Waveform Generator

Control Unit &

#1980A WB

Photometer

DMF-50316NF-FW-1 (AA) No.99-0188 OPTREX CORPORATION Page 9/17

OPTREX

4.I/O Terminal

4.1.Pin Assignment

CN1

No. Symbol Level Function

1 FG － Frame Ground

2 V

SS ― Po wer Supply (0V, GND)

3 V

CC ― Power Supply for Logic

4 V

EE ― Po wer Supply for LCD Drive

5 WR H / L Write Signal L : Active

6 RD H / L Read Signal L : Active

7 CE H / L Chip Enable Signal L : Active

8 C/D H / L Write Mode H : Command Write L : Data Write

Read Mode H : Status Read L : Data Read

9 NC － Non-connection

10 RESET H / L Reset Signal L : Reset

11 D0 H / L Display Data

12 D1 H / L Display Data

13 D2 H / L Display Data

14 D3 H / L Display Data

15 D4 H / L Display Data

16 D5 H / L Display Data

17 D6 H / L Display Data

18 D7 H / L Display Data

19 FS H / L Font Switch H : 6×8 dots L : 8×8 dots

20 INVERT H / L Display Data Reverse Signal H : Reverse L : Normal

CN2

No. Symbol Level Function

1 CFL － Power Supply for CFL (HOT)

2 NC － Non-connection

3 NC － Non-connection

4 CFL (GND) － Power Supply for CFL (GND)

DMF-50316NF-FW-1 (AA) No.99-0188 OPTREX CORPORATION Page 10/17

OPTREX

4.2.Example of Power Supply

It is recommended to apply a potentiometer for the contrast adjust due to the tolerance

of the driving voltage and its temperature dependence.

4.3.Block Diagram

VSS

MODULE

VEE

VCC

VEE (-Voltage)

VCC (+Voltage)

Tr=2SA1202 or equivalent

R1+R2+VR=10～20KΩ

VSS (0V)

CFL(GND)

CFL

VEE

VSS

VCC

INVERT

D0～D7

C/D

RESET

or equivalent

T6A40 × 1

T6963C-0101

Control LSI

Row Driver

Nega/Posi Reve rs e circuit

or equivalent

T6A39 × 3

Column Diver

L C D P

3240

240 × 64 dots

TO LS I

Bias Circuit

CFL B a ckligh t

X-tal 813

64K S-RAM

DMF-50316NF-FW-1 (AA) No.99-0188 OPTREX CORPORATION Page 11/17

OPTREX

5.Test

No change on display and in operation under the following test condition.

No. Parameter Conditions Notes

1 High Temperature Operating 50℃±2℃, 96hrs (operation state)

2 Low Temperature Operating 0℃±2℃, 96hrs (operation state) 3

3 High Temperature Storage 60℃±2℃, 96hrs 4

4 Low Temperature Storage -20℃±2℃, 96hrs 3, 4

5 Damp Proof Test 40℃±2℃, 90～95%RH, 96hrs 3, 4

6 Vibration Test Total fixed amplitude : 1.5mm 5

Vibration Frequency : 10～55Hz

One cycle 60 seconds to 3 directions of X, Y, Z for

each 15 minutes

7 Shock Test To be measured after dropping from 60cm high on

the concrete surface in packing state.

Note 1 : Unless otherwise specified, tests will be conducted under the following condition.

Temperature : 20±5℃

Humidity : 65±5%

Note 2 : Unless otherwise specified, tests will be not conducted under functioning state.

Note 3 : No dew condensation to be observed.

Note 4 : T he function test shall be conducted after 4 hours storage at the normal temperature and humidity

after removed from the test chamber.

Note 5 : Vib ration test will be conducted to the product itself without putting it in a container.

GDC

60cm

C o ncrete S urface

Dropping method corner dropping

E,F,G face : once

B,C,D edge : once

A corner : once

Face dropping

Edge drop ping

DMF-50316NF-FW-1 (AA) No.99-0188 OPTREX CORPORATION Page 12/17

OPTREX

6.Appearance Standards

6.1.Inspection conditions

The LCD shall be inspected under 40W white fluorescent light.

The distance between the eyes and the sample shall be more than 30cm.

All directions for inspecting the sample should be within 45 ﾟagainst perpendicular line.

6.2.Definition of applicable Zones

A Zone : Active display area

B Zone : Area from outside of "A Zone" to validity viewing area

C Zone : Rest parts

A Zone + B Zone = Validity vie wing area

A Zone

B Zone

C Zone

Bezel Flame

45ﾟ

DMF-50316NF-FW-1 (AA) No.99-0188 OPTREX CORPORATION Page 13/17

OPTREX

6.3.Standards

No. Parameter Criteria

1 Black and (1) Round Shape

White Spots, Zone Acceptable Number

Fore i gn Substances Dimension ( mm) A B C

D ≦0.1 * * *

0.1

＜ D ≦0.2 3 5 *

0.2

＜ D ≦0.25 2 3 *

0.25＜ D ≦0.3 0 1 *

0.3

＜ D 0 0 *

D = ( Long + Short ) / 2 * : Disregard

(2) Line Shape

Zone Acceptable Number

X (mm) Y (mm) A B C

－ 0.03≧W * * *

2.0≧L 0.05≧W 3 3 *

1.0≧L 0.1

≧W 3 3 *

－ 0.1

＜W In the same way (1)

X : Length Y : Width * : Disregard

Total defects shall not exceed 5.

2 Air Bubbles

(between glass Zone Acceptable Number

& polarizer) Dimen sion (mm) A B C

D ≦ 0.3 * * *

0.3

＜ D ≦ 0.4 3 * *

0.4

＜ D ≦ 0.6 2 3 *

0.6

＜ D 0 0 *

* : Disregard

Total defects shall not exceed 3.

DMF-50316NF-FW-1 (AA) No.99-0188 OPTREX CORPORATION Page 14/17

OPTREX

No. Parameter Criteria

3 The Shape of Dot (1) Dot Shape (with Dent)

As per the sketch of left hand.

(2) Dot Shape (with Projection)

Should not be connected t o next dot .

(3) Pin Hole

(X+Y) / 2≦0.2mm

(Less than 0.1mm is no counted.)

(4) Deformation

(X+Y) / 2≦0.2mm

Total acceptable number : 1/dot, 5/cell

(Defect number of (4) : 1pc.)

4 Polarizer Scratches Not to be conspicuous defects.

5 Polarizer Dirts If the stains are removed easily from LCDP surface, the module is not

defective.

6 Complex Foreign Black spots, line shaped foreign substances or air bubbles between

Substance Defects glass & polarizer should be 5pcs maximum in total.

7 Distance between D≦0.2 : 20mm or more

Different Foreign 0.2＜D : 40mm or more

Substance Defects

0.15≧

DMF-50316NF-FW-1 (AA) No.99-0188 OPTREX CORPORATION Page 15/17

OPTREX

7.Code System of Production Lot

The production lot of module is specified as follows.

□ □ □ □ □ □

Factory Number (Numeral)

Factory Code (Alphabet)

Production Week (1～5)

Pr oduction Month (1～9, X, Y, Z)

Production Year (Lower 2 digits)

8.Type Number

The type number of module is specified on the back of module as follows.

ＤＭＦ－５０３１６ＮＦ－ＦＷ－１

Stamp

Etchi ng or Pr i nting

9.Applying Precautions

Please contact us when questions and/or new problems not specified in this specifications arise.

DMF-50316NF-FW-1 (AA) No.99-0188 OPTREX CORPORATION Page 16/17

OPTREX

10.Precautions Relating Product Handling

The Following precautions will guide you in handling our product correctly.

1) Liquid crystal display devices

① The liquid crystal display device panel used in the liquid crystal display module is made of plate

glass. Avoid any strong mechanical shock. Should the glass break handle it with care.

② The polarizer adhering to the surface of the LCD is made of a soft material.

Guard against scratching it.

2) Care of the liquid crystal display module against static electricity discharge.

① When working with the module, be sure to ground your body and any electrical equipment you may

be using. We strongly recommend the use of anti static mats ( made of rubber ), to protect wo rk

tables against the hazards of electrical shock.

② Avoid the use of work clo thing made of synthetic fib ers. We rec ommend cotton clo thing or ot her

conductivity-treated fibers.

③ Slowly and carefully remove the protective film from the LCD module, since this operation can

generate static electricity.

3) When the LCD module alone must be stored for long periods of time:

① Protect the modules from high temperature and humidity.

② Keep the modules out of direct sunlight or direct exposure to ultraviolet rays.

③ Protect the modules from excessive external forces.

4) Use the module with a power supply that is equipped with an overcurrent protector circuit,

since the module is not provided with this protective feature.

5) Do not ingest the LCD fluid itself should it leak out of a damaged LCD module. Should hands

or clothing come in contact with LCD fluid, wash immediately with soap.

6) Conduc1tivity is not guaranteed for models that use metal holders where solder connections

between the metal holder and the PCB are not used. Please contact us to discuss appropriate

ways to assure conductivity.

7) For models which use CFL:

① High voltage of 1000V or greater is applied to the CFL cable connector area.

Care should be taken not to touch connection areas to avoid burns.

② Protect CFL cables from rubbing against the unit and thus causing the wire jacket to become worn.

③The use of CFLs for extended periods of time at low temperatures will significantly shorten their

service life.

DMF-50316NF-FW-1 (AA) No.99-0188 OPTREX CORPORATION Page 17/17

OPTREX

8) For mode l s which use t ouch panels:

①Do not stack up modules since they can be damaged by components on neighboring modules.

②Do not place heavy objects on top of the product. This could cause glass breakage.

9) For models which use COG,TAB,or COF:

①The mechanical strength of the product is low since the IC chip faces out unprotected from the rear.

Be sure to protect the rear of the IC chip from external forces.

②Given the fact that the rear of the IC chip is left exposed, in order to protect the unit from electrical

damage, avoid installation configurations in which the rear of the IC chip runs the risk of making

any electrical contact.

10) Models which use flexible cable, heat seal, or TAB:

①In order to maintain reliability, do not touch or hold by the connector area.

②Avoid any bending, pulling, or other excessive force, which can result in broken connections.

11.Warranty

This product has been manufactured to your company’s specifications as a part for use in your company’s

general electronic products. It is guaranteed to perform according to delivery specifications. For any other

use apart from general electronic equipment, we cannot take responsibility if the product is used in medical

devices, nuclear power control equipment, aerospace equipment, fire and security systems, or any other

applications in which there is a direct risk to human life and where extremely high levels of reliability are

required. If the product is to be used in any of the above applications, we will need to enter into a separate

product liability agreement.

① We cannot accept responsibility for any defect, which may arise from additional manufacturing of

the product (including disassembly and reassemb ly), after product delivery.

② We cannot accept responsibility for any defect, which may arise after the application of strong

external force to the product.

③ We cannot accept responsibility for any defect, which may arise due to the application of static

electricity after the product has passed your company’s acceptance inspection procedures.

④ When the product is in CFL models, CFL service life and brightness will vary according to the

performance of the inverter used, leaks, etc. We cannot accept responsibility for product

performance, reliability, or d efect, which may arise.

⑤ We cannot accept resp onsibility for industrial pr operty, which may arise through the use of your

prod uct, with exception to those issues relating directly to the structure or method of

manufacturing of our product.

⑥ Optrex will not be held responsible for any quality guarantee issue for defect products judged as

Optrex-origin longer than 2 (two) years from Optrex production or 1(one) year from Optrex, Optrex

America, Optrex Europe, Display LC delivery which ever comes later.