A1120LLHLT-TM08 - ALLEGRO MICROSYSTEMS

PRV6

www.vishay.com Vishay Sfernice

Revision: 04-Jul-17 1Document Number: 51035

For technical questions, contact: sferpottrimmers@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Fully Sealed Potentiometer Cermet or Conductive Plastic

FEATURES

• PRV6S high power rating 1.5 W at 70 °C (cermet)

• PRV6A 0.75 W at 70 °C (conductive plastic)

• Tests according to CECC 41000 or IEC 60393-1

•Low cost

• Fully sealed and panel sealed

• Compatible RV6 (MIL R 94)

• Mechanical endurance 50 000 cycles

• Material categorization: for definitions of compliance

please see www.vishay.com/doc?99912

QUICK REFERENCE DATA

Multiple module No

Switch module n/a

Detent module n/a

Special electrical laws A: linear, L: logarithmic, F: reverse

logarithmic

Sealing level IP 67

Lifespan 50K cycles

DIMENSIONS in millimeters (inches) ± 0.5 mm (± 0.02")

PRV6 STYLE A AND S PRV6 STYLE B AND C

SHAFT DIAMETER 3 mm (0.118")

BUSHING A-B-C

SHAFT DIAMETER 3.17 mm (0.125")

BUSHING A-B-C

SHAFT DIAMETER 4 mm (0.157")

BUSHING H-I (not panel sealed)

LEADS X = PCB PINS LEADS Y = SOLDER LUGS

9.5 (0.374)

5 (0.200)

0.8 (0.031)

12.1 (0.476)

5 (0.200)

0.8 (0.031)

Ø 3 (0.118)

Ø 3.17 (0.125)

B = see bushing table

0.8 (0.031)

Ø 4 (0.157)

5.08 (0.200)

2.15 (0.085)

Ø 12.7 (0.50)

0.8 x 0.3 (0.031 x 0.012)

2.4 (0.094)

0.8 (0.031)

0.5 (0.020)

5.08 (0.200)

2.15 (0.085)

Ø 12.7 (0.50)

1.6 x 0.3 (0.063 x 0.012)

PRV6

www.vishay.com Vishay Sfernice

Revision: 04-Jul-17 2Document Number: 51035

For technical questions, contact: sferpottrimmers@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

ELECTRICAL SPECIFICATIONS

PRV6S, PRV6B PRV6A, PRV6C

Resistive element cermet conductive plastic

Electrical travel 270° ± 15°

Resistance range linear taper (A) 20 Ω to 10 MΩ1 kΩ to 1 MΩ

non-linear taper (F-L) 470 Ω to 1 MΩ470 Ω to 500 kΩ (± 20 %)

Taper

Tolerance standard ± 20 % ± 20 %

on request ± 10 %, ± 5 % ± 10 % (1 kΩ to 100 kΩ)

Circuit diagram

Power rating at 70 °C linear 1.5 W at 70 °C 0.75 W at 70 °C

other tapers 0.75 W 0.4 W

Power rating chart

Temperature coefficient (typical) ± 150 ppm/°C ± 500 ppm/°C

Limiting element voltage 350 V

Contact resistance variation (CRV) 2 % or 3 Ω

End resistance (typical) 1 Ω

Dielectric strength (RMS) 1750 VRMS

Insulation resistance (500 VDC)106 MΩ

90 %

25°

15° Electrical travel 270°

Mechanical travel 300°

50 %

20 %

10 %

15°

50° 75°

bcw

(2)

(3)

(1)

0 40 125

0.75

AMBIENT TEMPERA TURE IN DEGREES CELSIUS

WER IN WATT

20 100

PRV6S, PRV6B linear taper

0.4

1.50

PRV6S, PRV6B non-linear taper

PRV6A, PRV6C linear taper

PRV6A, PRV6C non-linear taper

PRV6

www.vishay.com Vishay Sfernice

Revision: 04-Jul-17 3Document Number: 51035

For technical questions, contact: sferpottrimmers@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Note

• Nothing stated herein shall be construed as a guarantee of quality or durability

MECHANICAL SPECIFICATIONS

Mechanical travel 300° ± 5°

Operating torque (Ncm (oz.in.)) 0.5 to 2 (0.7 to 3)

End stop torque (max. Ncm (lb.in.)) 35 (3)

Tightening torque (max. Ncm (lb.in.)) 150 (13)

ENVIRONMENTAL SPECIFICATIONS

PRV6S, PRV6B PRV6A, PRV6C

Temperature range -55 °C to +125 °C -40 °C to +125 °C

Climatic category 55/125/56 40/125/56

Sealing Fully sealed container; IP67 and panel sealed

PERFORMANCES

TESTS CONDITIONS TYPICAL VALUES AND DRIFTS

ΔRT/RT (%) ΔR1-2/R1-2 (%) OTHER

Electrical endurance 1000 h at rated power

90'/30' - temperature 70 °C ± 1 % CRV < 3 % Rn

Climatic sequence

Phase A dry heat 100 °C

Phase B damp heat

Phase C cold -55 °C

Phase D damp heat 5 cycles

± 0.5 % ± 1 %

Damp heat, steady state 56 days ± 0.5 % ± 1 % Insulation resistance: > 104 MΩ

Change of temperature 5 cycles, -55 °C to +125 °C ± 0.5 %

Mechanical endurance 50 000 cycles ± 3 % CRV < 2 % Rn

Shock

50 g at 11 ms

3 successive shocks

in 3 directions

± 0.1 % ± 0.2 %

Vibration 10 Hz to 55 Hz

0.75 mm or 10 g during 6 h ± 0.1 % ± 0.2 %

STANDARD RESISTANCE ELEMENT DATA

STANDARD

RESISTANCE

VALUES

PRV6S AND PRV6B WITH LINEAR TAPER PRV6S AND PRV6B WITH NON-LINEAR TAPER

MAX.

POWER

AT 70 °C

MAX.

WORKING

VOLTAGE

MAX.

WIPER

CURRENT

MAX.

POWER

AT 70 °C

MAX.

WORKING

VOLTAGE

MAX.

WIPER

CURRENT

ΩWV mA WV mA

20 1.5 5.48 274

50 1.5 8.66 173

100 1.5 12.2 122

200 1.5 17.3 87

500 1.5 27.4 55 0.75 19.4 39

1K 1.5 38.7 38.7 0.75 27.3 27.4

2K 1.5 54.8 27.4 0.75 38.2 19.3

5K 1.5 86.6 17.3 0.75 61.2 12.2

10K 1.5 122.5 12.2 0.75 87 8.7

20K 1.5 173 8.26 0.75 122 6.1

50K 1.5 274 5.65 0.75 194 3.9

100K 1.22 350 3.5 0.75 273 2.74

220K 0.61 350 1.75 0.61 350 1.75

500K 0.25 350 0.70 0.25 350 0.7

1M 0.12 350 0.35 0.12 350 0.35

2M 0.06 350 0.17

5M 0.025 350 0.070

10M 0.012 350 0.035

PRV6

www.vishay.com Vishay Sfernice

Revision: 04-Jul-17 4Document Number: 51035

For technical questions, contact: sferpottrimmers@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

MARKING

• Vishay trademark

• Part number

• Manufacturing date code

•Terminal: 1

PACKAGING

• Box of 15, 20, 25, or 50 pieces, code B12, B15, B17, or B25, depending of body and shaft construction

OPTIONS

SPECIAL FEATURES

Panel sealing

Except for dia. 4 mm shaft, an O.ring is supplied with the potentiometer. This O.ring should be placed

into the groove of the body and ensures the panel sealing.

For dia. 4 mm shaft please see note “P” in ordering information.

Shaft locking

Shafts Shaft lengths are measured from the mounting face to the free end of the shaft. Special shafts are

available if the customer supplies a drawing. The shaft slot is aligned to the wiper within ± 10°.

Hardware Nuts, washer and O.ring are separately supplied (not mounted on the potentiometer), in a small bag

placed in the packaging.

Locating peg

Except for dia. 4 mm shaft, the potentiometers are delivered with 2 opposite locating pegs orientated

at 45°.These 2 pegs can be easily broken-off by the customer. On request, the orientation of the pegs

can be at 30° instead of 45°.

PRV6

www.vishay.com Vishay Sfernice

Revision: 04-Jul-17 5Document Number: 51035

For technical questions, contact: sferpottrimmers@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Note

(1) Not standard, special manufacturing

LOCATING PEG CODE

BUSHING OLD CODE A L R 0

A6xx x

(1)

B61x x x

(1)

C62 x x x

(1)

D61Hx x x

(1)

E62Hx x x

(1)

H6Q x

I 61Q x

J6QP x

K 61QP x

S 61QH x

S61QPH x

ORDERING INFORMATION

(part number)

MODEL STYLE BUSHING LOCATING

PEG SHAFT LEADS PACKAGING

RESISTANCE CODE/

TOLERANCE/

TAPER OR SPECIAL

PRV6 S = standard

A = audio

B = body

length

C = audio

and body

length

ØL

Old

codes

0 = without

A = 45°

L = 30°

R = 180°

round

(see locating

peg table

above)

ØL

Old

codes

X =

PCB

pins

(old

code

Y =

solder

lugs

Depending of

body and shaft

construction:

B12 = box 15 pcs

B15 = box 20 pcs

B17 = box 25 pcs

B25 = box 50 pcs

Resistance:

from

200 = 20

106 = 10 M

for

linear cermet

Tolerance:

standard

M = 20 %

on request

K = 10 % or

J = 5 %

Taper: A, L, F

special code

given by

Vishay

A1/4 1/4 6 AA 3 9.5 K

B 1/4 3/8 61 AB 3 12.5 M

C1/4 1/2 62 AJ 3 22 R

D 1/4 3/8 61H BA 1/8 9.5 CK

E 1/4 1/2 62H BB 1/8 12.5 CM

H 7 6.5 6Q BG 1/8 16 CD

I 7 9.5 61Q BJ 1/8 22 CR

J7 6.5 6QP EA4 9.5 E

K 7 9.5 61QP EB 4 12.5 F

S 7 9.5 61QH EJ 4 22 G

S 7 9.5 61QPH AP custom shaft

all are slotted

PART NUMBER DESCRIPTION (for information only using old codes)

PRV S 61 W CD 5K 20 % A BO e3

MODEL BUSHING LEADS SPECIAL SHAFT VALUE TOLERANCE TAPER SPECIAL PACKAGING SPECIAL AP N

SPECIAL LEAD

FINISH

RELATED DOCUMENTS

APPLICATION NOTES

Potentiometers and Trimmers www.vishay.com/doc?51001

Guidelines for Vishay Sfernice Resistive and Inductive Components www.vishay.com/doc?52029

6BBA G 17BRV 025P MAX B

Legal Disclaimer Notice

www.vishay.com Vishay

Revision: 08-Feb-17 1Document Number: 91000

Disclaimer



ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE

RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.

Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,

“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other

disclosure relating to any product.

Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or

the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all

liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,

consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular

purpose, non-infringement and merchantability.

Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of

typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding

statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a

particular product with the properties described in the product specification is suitable for use in a particular application.

Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over

time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s

technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,

including but not limited to the warranty expressed therein.

Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining

applications or for any other application in which the failure of the Vishay product could result in personal injury or death.

Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk.

Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for

such applications.

No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document

or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.