SN74AVCBH324245 32-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES550B - FEBRUARY 2004 - REVISED JUNE 2005 * FEATURES * * * * * Member of the Texas Instruments Widebus+TM Family DOCTM Circuitry Dynamically Changes Output Impedance, Resulting in Noise Reduction Without Speed Degradation Dynamic Drive Capability Is Equivalent to Standard Outputs With IOH and IOL of - 24 mA at 3-V VCC - 15 mA at 2.3-V VCC - 9 mA at 1.65-V VCC - 6 mA at 1.4-V VCC Control Inputs VIH/VIL Levels Are Referenced to VCCB Voltage If Either VCC Input Is at GND, Both Ports Are in the High-Impedance State * * * * * Inputs/Outputs Can Tolerate up to 4.6 V, Which Allows Mixed-Voltage-Mode Data Communications Ioff Supports Partial-Power-Down Mode Operation Fully Configurable Dual-Rail Design Allows Each Port to Operate Over Full 1.4-V to 3.6-V Power-Supply Range Bus Hold on Data Inputs Eliminates the Need for External Pullup/Pulldown Resistors Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II ESD Protection Exceeds JESD 22 - 2000-V Human-Body Model (A114-A) - 200-V Machine Model (A115-A) - 1000-V Charged-Device Model (C101) DESCRIPTION/ORDERING INFORMATION This 32-bit noninverting bus transceiver uses two separate configurable power-supply rails. The A port is designed to track VCCA. VCCA accepts any supply voltage from 1.4 V to 3.6 V. The B port is designed to track VCCB. VCCB accepts any supply voltage from 1.4 V to 3.6 V. This allows for universal low-voltage bidirectional translation between any of the 1.5-V, 1.8-V, 2.5-V, and 3.3-V voltage nodes. The SN74AVCBH324245 is designed for asynchronous communication between data buses. The device transmits data from the A bus to the B bus or from the B bus to the A bus, depending on the logic level at the direction-control (DIR) input. The output-enable (OE) input is used to disable the outputs, so the buses effectively are isolated. The SN74AVCBH324245 is designed so that the control pins (1DIR, 2DIR, 1OE, and 2OE) are supplied by VCCB. Active bus-hold circuitry is provided to hold unused or floating data inputs at a valid logic level. Use of pullup or pulldown resistors with the bus-hold circuitry is not recommended. To ensure the high-impedance state during power up or power down, OE should be tied to VCCB through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver. This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs, preventing damaging current backflow through the device when it is powered down. If either VCC input is at GND, both ports are in the high-impedance state. ORDERING INFORMATION PACKAGE (1) TA -40C to 85C (1) ORDERABLE PART NUMBER LFBGA - GKE Tape and reel SN74AVCBH324245KR LFBGA - ZKE Tape and reel 74AVCBH324245ZKER TOP-SIDE MARKING WN4245 Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Widebus+, DOC are trademarks of Texas Instruments. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2004-2005, Texas Instruments Incorporated SN74AVCBH324245 32-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES550B - FEBRUARY 2004 - REVISED JUNE 2005 GKE PACKAGE (TOP VIEW) 1 2 3 4 5 6 A B C D E F G H J K L M N P R T TERMINAL ASSIGNMENTS 2 1 2 3 4 5 6 A 1B2 1B1 B 1B4 1B3 1DIR 1OE 1A1 1A2 GND GND 1A3 C 1B6 1A4 1B5 VCCB VCCA 1A5 D 1A6 1B8 1B7 GND GND 1A7 1A8 E 2B2 2B1 GND GND 2A1 2A2 F 2B4 2B3 VCCB VCCA 2A3 2A4 G 2B6 2B5 GND GND 2A5 2A6 H 2B7 2B8 2DIR 2OE 2A8 2A7 J 3B2 3B1 3DIR 3OE 3A1 3A2 K 3B4 3B3 GND GND 3A3 3A4 L 3B6 3B5 VCCB VCCA 3A5 3A6 M 3B8 3B7 GND GND 3A7 3A8 N 4B2 4B1 GND GND 4A1 4A2 P 4B4 4B3 VCCB VCCA 4A3 4A4 R 4B6 4B5 GND GND 4A5 4A6 T 4B7 4B8 4DIR 4OE 4A8 4A7 www.ti.com SN74AVCBH324245 32-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS SCES550B - FEBRUARY 2004 - REVISED JUNE 2005 FUNCTION TABLE (EACH 8-BIT SECTION) INPUTS OE DIR OPERATION L L B data to A bus L H A data to B bus H X Isolation LOGIC DIAGRAM (POSITIVE LOGIC) 1DIR A3 2DIR A4 1A1 H4 1OE A5 2A1 A2 H3 E5 E2 1B1 To Seven Other Channels 3DIR J3 4DIR T4 4A1 J2 T3 3OE J5 To Seven Other Channels 2B1 To Seven Other Channels J4 3A1 2OE 4OE N5 N2 3B1 4B1 To Seven Other Channels 3 SN74AVCBH324245 32-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES550B - FEBRUARY 2004 - REVISED JUNE 2005 Absolute Maximum Ratings (1) over operating free-air temperature range (unless otherwise noted) VCCA VCCB Supply voltage range VI Input voltage range (2) MIN MAX -0.5 4.6 I/O port (A port) -0.5 4.6 I/O port (B port) -0.5 4.6 Control inputs -0.5 4.6 A port -0.5 4.6 B port -0.5 4.6 A port -0.5 VCCA + 0.5 B port -0.5 VCCB + 0.5 UNIT V V VO Voltage range applied to any output in the high-impedance or power-off state (2) VO Voltage range applied to any output in the high or low state (2) (3) IIK Input clamp current VI < 0 -50 mA IOK Output clamp current VO < 0 -50 mA IO Continuous output current 50 mA Continuous current through each VCCA, VCCB, or GND JA Package thermal impedance (4) Tstg Storage temperature range (1) (2) (3) (4) 4 100 GKE/ZKE package -65 V V mA 40 C/W 150 C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. The input voltage and output negative-voltage ratings may be exceeded if the input and output current ratings are observed. The output positive-voltage rating may be exceeded up to 4.6 V maximum if the output current rating is observed. The package thermal impedance is calculated in accordance with JESD 51-7. www.ti.com SN74AVCBH324245 32-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS SCES550B - FEBRUARY 2004 - REVISED JUNE 2005 Recommended Operating Conditions (1) (2) (3) VCCI VCCO MIN MAX UNIT VCCA Supply voltage 1.4 3.6 V VCCB Supply voltage 1.4 3.6 V 1.4 V to 1.95 V VCCI x 0.65 3.6 1.95 V to 2.7 V 1.7 3.6 2.7 V to 3.6 V 2 3.6 1.4 V to 1.95 V 0 VCCI x 0.35 1.95 V to 2.7 V 0 0.7 2.7 V to 3.6 V 0 0.8 1.4 V to 1.95 V VCCB x 0.65 VCCB 1.95 V to 2.7 V 1.7 VCCB VIH High-level input voltage VIL Low-level input voltage VIH High-level input voltage VIL Low-level input voltage VO Output voltage IOH Data inputs Data inputs Control inputs (referenced to VCCB) Control inputs (referenced to VCCB) High-level output current IOL Low-level output current t/v Input transition rise or fall rate TA Operating free-air temperature (1) (2) (3) 2.7 V to 3.6 V 2 VCCB 1.4 V to 1.95 V 0 VCCB x 0.35 1.95 V to 2.7 V 0 0.7 2.7 V to 3.6 V 0 0.8 0 VCCO 1.4 V to 1.6 V -2 1.65 V to 1.95 V -4 2.3 V to 2.7 V -8 3 V to 3.6 V -12 1.4 V to 1.6 V 2 1.65 V to 1.95 V 4 2.3 V to 2.7 V 8 3 V to 3.6 V 12 -40 V V V V V mA mA 5 ns/V 85 C VCCI is the VCC associated with the data input port. VCCO is the VCC associated with the output port. All unused data inputs of the device must be held at VCCI or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. 5 SN74AVCBH324245 32-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES550B - FEBRUARY 2004 - REVISED JUNE 2005 Electrical Characteristics (1) over recommended operating free-air temperature range (unless otherwise noted) PARAMETER VOH VOL VOH VOL II Control inputs IBHL (3) IBHH (4) TEST CONDITIONS IBHHO (6) (1) (2) (3) (4) (5) (6) 6 VCCB MIN TYP (2) MAX IOH = -100 A, VI = VIH 1.4 V to 3.6 V 1.4 V to 3.6 V IOH = -2 mA, VI = VIH 1.4 V 1.4 V IOH = -4 mA, VI = VIH 1.65 V 1.65 V 1.2 IOH = -8 mA, VI = VIH 2.3 V 2.3 V 1.75 IOH = -12 mA, VI = VIH 3V 3V 2.3 IOH = 100 A, VI = VIL 1.4 V to 3.6 V 1.4 V to 3.6 V 0.2 IOH = 2 mA, VI = VIL 1.4 V 1.4 V 0.35 IOH = 4 mA, VI = VIL 1.65 V 1.65 V 0.45 IOH = 8 mA, VI = VIL 2.3 V 2.3 V 0.55 IOH = 12 mA, VI = VIL 3V 3V IOHD = -6 mA, VI = VIH 1.4 V 1.4 V 1.05 IOHD = -9 mA, VI = VIH 1.65 V 1.65 V 1.2 IOHD = -15 mA, VI = VIH 2.3 V 2.3 V 1.75 IOHD = -24 mA, VI = VIH 3V 3V 2.3 IOHD = 6 mA, VI = VIL 1.4 V 1.4 V 0.35 IOHD = 9 mA, VI = VIL 1.65 V 1.65 V 0.45 IOHD = 15 mA, VI = VIL 2.3 V 2.3 V 0.55 IOHD = 24 mA, VI = VIL 3V 3V 0.7 VI = VCCB or GND 1.05 3.6 V 1.4 V 1.4 V VI = 0.57 V 1.65 V 1.65 V 25 VI = 0.7 V 2.3 V 2.3 V 45 V 75 V 2.5 V A 11 VI = 0.8 V 3V 3V VI = 0.49 V 1.4 V 1.4 V VI = 1.07 V 1.65 V 1.65 V -25 VI = 1.7 V 2.3 V 2.3 V -45 VI = 0 to VCC V 0.7 1.4 V to 3.6 V VI = 0 to VCC UNIT VCCO - 0.2 VI = 0.49 V VI = 2 V IBHLO (5) VCCA A -11 3V 3V -75 1.6 V 1.6 V 100 1.95 V 1.95 V 200 2.7 V 2.7 V 300 3.6 V 3.6 V 525 1.6 V 1.6 V -100 1.95 V 1.95 V -200 2.7 V 2.7 V -300 3.6 V 3.6 V -525 A A A VCCO is the VCC associated with the output port. All typical values are at TA = 25C. The bus-hold circuit can sink at least the minimum low sustaining current at VIL max. IBHL should be measured after lowering VIN to GND and then raising it to VIL max. The bus-hold circuit can source at least the minimum high sustaining current at VIH min. IBHH should be measured after raising VIN to VCC and then lowering it to VIH min. An external driver must source at least IBHLO to switch this node from low to high. An external driver must sink at least IBHHO to switch this node from high to low. SN74AVCBH324245 32-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES550B - FEBRUARY 2004 - REVISED JUNE 2005 Electrical Characteristics (1) (2) (continued) over recommended operating free-air temperature range (unless otherwise noted) PARAMETER TEST CONDITIONS A port Ioff VI or VO = 0 to 3.6 V B port A or B port IOZ (4) VO = VCCO or GND, VI = VCCI or GND B port A port ICCA VI = VCCI or GND, ICCB VI = VCCI or GND, OE = VIH OE = don't care IO = 0 IO = 0 MIN TYP (3) VCCA VCCB 0V 0 to 3.6 V MAX 10 0 to 3.6 V 0V 10 3.6 V 3.6 V 12.5 0V 3.6 V 12.5 3.6 V 0V 12.5 1.6 V 1.6 V 40 1.95 V 1.95 V 40 2.7 V 2.7 V 60 0V 3.6 V -80 3.6 V 0V 80 3.6 V 3.6 V 80 1.6 V 1.6 V 40 1.95 V 1.95 V 40 2.7 V 2.7 V 60 0V 3.6 V 80 3.6 V 0V -80 3.6 V 3.6 V UNIT A A A A 80 Ci Control inputs VI = 3.3 V or GND 3.3 V 3.3 V 4 pF Cio A or B ports VO = 3.3 V or GND 3.3 V 3.3 V 5 pF (1) (2) (3) (4) VCCO is the VCC associated with the output port. VCCI is the VCC associated with the input port. All typical values are at TA = 25C. For I/O ports, the parameter IOZ includes the input leakage current. Switching Characteristics over recommended operating free-air temperature range, VCCA = 1.5 V 0.1 V (see Figure 2) PARAMETER tpd FROM (INPUT) TO (OUTPUT) A B ten OE tdis OE VCCB = 1.5 V 0.1 V VCCB = 1.8 V 0.15 V VCCB = 2.5 V 0.2 V VCCB = 3.3 V 0.3 V MIN MAX MIN MAX MIN MAX MIN MAX B 1.7 6.7 1.9 6.4 1.8 5.5 1.5 5.8 A 1.8 6.8 1.7 6.2 1.6 5.9 1.5 5.9 A 2.1 9 2.9 9.8 3.2 10 3 9.8 B 2.5 8.4 2.4 8 2.3 7.6 2.2 7.5 A 2.1 7.1 2.3 6.4 1.7 5.1 1.6 4.8 B 2.2 6.9 1.8 6.4 1.1 5.8 1.8 5.7 UNIT ns ns ns Switching Characteristics over recommended operating free-air temperature range, VCCA = 1.8 V 0.15 V (see Figure 2) PARAMETER tpd FROM (INPUT) TO (OUTPUT) A B ten OE tdis OE VCCB = 1.5 V 0.1 V VCCB = 1.8 V 0.15 V VCCB = 2.5 V 0.2 V VCCB = 3.3 V 0.3 V MIN MAX MIN MAX MIN MAX MIN MAX B 1.7 6.4 1.8 6 1.7 4.7 1.6 4.3 A 2 6.6 1.8 6 1.8 5.6 1.8 5.5 A 1.8 7.6 2.6 7.7 2.6 7.6 2.6 7.4 B 2.5 8.2 2.5 7.5 2.4 7.4 2.3 7.2 A 1.8 7 2.5 6.3 1.8 4.7 1.7 4.4 B 2.5 6.7 2.3 6.1 2.2 5.5 1.3 5.3 UNIT ns ns ns 7 SN74AVCBH324245 32-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES550B - FEBRUARY 2004 - REVISED JUNE 2005 Switching Characteristics over recommended operating free-air temperature range, VCCA = 2.5 V 0.2 V (see Figure 2) PARAMETER tpd FROM (INPUT) TO (OUTPUT) A B B A ten OE tdis OE VCCB = 1.5 V 0.1 V MIN VCCB = 1.8 V 0.15 V VCCB = 2.5 V 0.2 V VCCB = 3.3 V 0.3 V MAX MIN MAX MIN MAX MIN MAX 1.6 6 1.8 5.6 1.5 4 1.5 3.4 1.7 5.4 1.7 4.6 1.5 4 1.5 3.7 A 1.7 5.7 2.2 5.5 2.2 5.3 2.2 5.1 B 3.1 6.1 2.5 5.6 2.2 5.3 1.9 4.2 A 1.2 5.8 1.9 5 1.4 3.6 1.3 3.3 B 2.4 6 3 5.2 1.4 3.6 1.2 3 UNIT ns ns ns Switching Characteristics over recommended operating free-air temperature range, VCCA = 3.3 V 0.3 V (see Figure 2) PARAMETER tpd FROM (INPUT) TO (OUTPUT) A B ten OE tdis OE VCCB = 1.5 V 0.1 V VCCB = 1.8 V 0.15 V VCCB = 2.5 V 0.2 V VCCB = 3.3 V 0.3 V MIN MAX MIN MAX MIN MAX MIN MAX B 1.5 5.9 1.7 5.4 1.5 3.7 1.4 3.1 A 1.5 5.8 1.5 4.2 1.5 3.3 1.4 3.1 A 1.6 4.9 2 4.5 2 4.3 1.9 4.1 B 2 5.1 2 4.6 2.2 5.2 1.9 4.1 A 1.3 6.9 2.1 5.5 1.6 3.8 1.5 3.5 B 2.3 5.5 1.9 4.5 1.3 3.5 1.2 3.5 UNIT ns ns ns Operating Characteristics VCCA and VCCB = 3.3 V, TA = 25C PARAMETER CpdA (VCCA) CpdB (VCCB) 8 TEST CONDITIONS TYP Power-dissipation capacitance per transceiver, A-port input, B-port output Outputs enabled Power-dissipation capacitance per transceiver, B-port input, A-port output Outputs enabled Outputs disabled 7 Power-dissipation capacitance per transceiver, A-port input, B-port output Outputs enabled 20 Power-dissipation capacitance per transceiver, B-port input, A-port output Outputs enabled Outputs disabled Outputs disabled Outputs disabled UNIT 14 CL = 0, CL = 0, f = 10 MHz f = 10 MHz 7 20 7 14 7 pF pF SN74AVCBH324245 32-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES550B - FEBRUARY 2004 - REVISED JUNE 2005 Output Description The DOCTM circuitry is implemented, which, during the transition, initially lowers the output impedance to effectively drive the load and, subsequently, raises the impedance to reduce noise. Figure 1 shows typical VOL vs IOL and VOH vs IOH curves to illustrate the output impedance and drive capability of the circuit. At the beginning of the signal transition, the DOC circuit provides a maximum dynamic drive that is equivalent to a high-drive standard-output device. For more information, refer to the TI application reports, AVC Logic Family Technology and Applications, literature number SCEA006, and Dynamic Output Control (DOCTM) Circuitry Technology and Applications, literature number SCEA009. 3.2 TA = 25C Process = Nominal - Output Voltage - V 2.8 2.4 VCC = 3.3 V 2.0 1.6 VCC = 2.5 V 1.2 OH VCC = 1.8 V 0.8 V VOL - Output Voltage - V 2.8 TA = 25C Process = Nominal 2.4 2.0 1.6 1.2 0.8 VCC = 3.3 V 0.4 0.4 0 17 34 51 68 85 102 119 IOL - Output Current - mA 136 153 170 VCC = 2.5 V VCC = 1.8 V -160 -144 -128 -112 -96 -80 -64 -48 IOH - Output Current - mA -32 -16 0 Figure 1. Typical Output Voltage vs Output Current 9 SN74AVCBH324245 32-BIT DUAL-SUPPLY BUS TRANSCEIVER WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS www.ti.com SCES550B - FEBRUARY 2004 - REVISED JUNE 2005 PARAMETER MEASUREMENT INFORMATION 2 x VCCO S1 RL From Output Under Test Open GND CL (see Note A) TEST S1 tpd tPLZ/tPZL tPHZ/tPZH Open 2 x VCCO GND RL tw LOAD CIRCUIT VCCI VCCI/2 Input VCCO CL RL VTP 1.5 V 0.1 V 1.8 V 0.15 V 2.5 V 0.2 V 3.3 V 0.3 V 15 pF 30 pF 30 pF 30 pF 2 k 1 k 500 500 0.1 V 0.15 V 0.15 V 0.3 V VCCI/2 0V VOLTAGE WAVEFORMS PULSE DURATION VCCB Output Control (low-level enabling) VCCB/2 VCCB/2 0V tPZL VCCI Input VCCI/2 VCCI/2 0V tPLH Output tPHL VCCO/2 VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES VOH VCCO/2 VOL tPLZ VCCO Output Waveform 1 S1 at 2 x VCCO (see Note B) VCCO/2 VOL + VTP VOL tPZH Output Waveform 2 S1 at GND (see Note B) tPHZ VCCO/2 VOH - VTP VOH 0V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR10 MHz, ZO = 50 , dv/dt 1 V/ns. D. The outputs are measured one at a time, with one transition per measurement. E. tPLZ and tPHZ are the same as tdis. F. tPZL and tPZH are the same as ten. G. tPLH and tPHL are the same as tpd. H. VCCI is the VCC associated with the input port. I. VCCO is the VCC associated with the output port. Figure 2. Load Circuit and Voltage Waveforms 10 PACKAGE OPTION ADDENDUM www.ti.com 30-Jan-2012 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) Samples (Requires Login) 74AVCBH324245ZKER ACTIVE LFBGA ZKE 96 1000 Green (RoHS & no Sb/Br) SNAGCU Level-3-260C-168 HR SN74AVCBH324245KR NRND LFBGA GKE 96 1000 TBD SNPB Level-2-235C-1 YEAR (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 28-Jan-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 74AVCBH324245ZKER LFBGA ZKE 96 1000 330.0 24.4 5.7 13.7 2.0 8.0 24.0 Q1 SN74AVCBH324245KR LFBGA GKE 96 1000 330.0 24.4 5.7 13.7 2.0 8.0 24.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 28-Jan-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) 74AVCBH324245ZKER SN74AVCBH324245KR LFBGA ZKE 96 1000 333.2 345.9 31.8 LFBGA GKE 96 1000 333.2 345.9 31.8 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated