LM6152, LM6154 www.ti.com SNOS752D - MAY 1999 - REVISED MARCH 2013 LM6152/LM6154 Dual and Quad 75 MHz GBW Rail-to-Rail I/O Operational Amplifiers Check for Samples: LM6152, LM6154 FEATURES DESCRIPTION * * Using patented circuit topologies, the LM6152/LM6154 provides new levels of speed vs. power performance in applications where low voltage supplies or power limitations previously made compromise necessary. With only 1.4 mA/amplifier supply current, the 75 MHz gain bandwidth of this device supports new portable applications where higher power devices unacceptably drain battery life. The slew rate of the devices increases with increasing input differential voltage, thus allowing the device to handle capacitive loads while maintaining large signal amplitude. 1 2 * * * * * * * * At VS = 5V, typical unless noted. Greater than rail-to-rail input CMVR -0.25V to 5.25V Rail-to-rail output swing 0.01V to 4.99V Wide gain-bandwidth 75 MHz @ 100 kHz Slew rate - Small signal 5 V/s - Large signal 45 V/s Low supply current 1.4 mA/amplifier Wide supply range 2.7V to 24V Fast settling time of 1.1 s for 2V step (to 0.01%) PSRR 91 dB CMRR 84 dB APPLICATIONS * * * Portable high speed instrumentation Signal conditioning amplifier/ADC buffers Barcode scanners The LM6152/LM6154 can be driven by voltages that exceed both power supply rails, thus eliminating concerns about exceeding the common-mode voltage range. The rail-to-rail output swing capability provides the maximum possible dynamic range at the output. This is particularly important when operating on low supply voltages. Operating on supplies from 2.7V to over 24V, the LM6152/LM6154 is excellent for a very wide range of applications, from battery operated systems with large bandwidth requirements to high speed instrumentation. Connection Diagrams Top View Figure 1. 8-Pin SOIC Package See Package Number D0008A Top View Figure 2. 14-Pin SOIC Package See Package Number D0014A These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 1999-2013, Texas Instruments Incorporated LM6152, LM6154 SNOS752D - MAY 1999 - REVISED MARCH 2013 Absolute Maximum Ratings ESD Tolerance www.ti.com (1) (2) (3) 2500V Differential Input Voltage 15V (V+) + 0.3V, (V-) -0.3V Voltage at Input/Output Pin Supply Voltage (V+ - V-) 35V Current at Input Pin Current at Output Pin 10 mA (4) 25 mA Current at Power Supply Pin 50 mA Lead Temperature (soldering, 10 sec) 260C Storage Temperature Range Junction Temperature (1) (2) (3) (4) (5) -65C to +150C (5) 150C Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but specific performance is not ensured. For ensured specifications and the test conditions, see the Electrical Characteristics. If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and specifications. Human body model is 1.5 k in series with 100 pF. Applies to both single-supply and split-supply operation. Continuous short circuit operation at elevated ambient temperature can result in exceeding the maximum allowed junction temperature of 150C. The maximum power dissipation is a function of TJ(MAX) , JA, and TA. The maximum allowable power dissipation at any ambient temperature is PD = (TJ(MAX)-T A)/JA. All numbers apply for packages soldered directly into a PC board. Operating Ratings (1) 2.7V V+ 24V Supply Voltage Junction Temperature Range Thermal Resistance (JA) (1) 0C TJ + 70C LM6152,LM6154 8-pin SOIC 193C/W 14-pin SOIC 126C/W Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but specific performance is not ensured. For ensured specifications and the test conditions, see the Electrical Characteristics. 5.0V DC Electrical Characteristics Unless otherwise specified, all limits are ensured for TJ = 25C, V+ = 5.0V, V- = 0V, VCM = VO = V+/2 and RL > 1 M to V+/2. Boldface limits apply at the temperature extremes. Parameter Test Conditions LM6152AC Limit (2) LM6154BC LM6152BC Limit (2) Units 2 4 5 7 mV max 500 750 980 1500 980 1500 nA max 32 40 100 160 100 160 nA max Typ (1) VOS Input Offset Voltage 0.54 TCVOS Input Offset Voltage Average Drift IB Input Bias Current IOS Input Offset Current RIN Input Resistance, CM 0V VCM 4V 30 CMRR Common Mode Rejection Ratio 0V VCM 4V 94 70 70 0V VCM 5V 84 60 60 91 80 80 dB min 10 0V VCM 5V V/C M dB min PSRR Power Supply Rejection Ratio 5V V+ 24V VCM Input Common-Mode Voltage Range Low -0.25 0 0 V High 5.25 5.0 5.0 V RL = 10 k 214 50 50 V/mV min AV (1) (2) 2 Large Signal Voltage Gain Typical Values represent the most likely parametric norm. All limits are specified by testing or statistical analysis. Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: LM6152 LM6154 LM6152, LM6154 www.ti.com SNOS752D - MAY 1999 - REVISED MARCH 2013 5.0V DC Electrical Characteristics (continued) Unless otherwise specified, all limits are ensured for TJ = 25C, V+ = 5.0V, V- = 0V, VCM = VO = V+/2 and RL > 1 M to V+/2. Boldface limits apply at the temperature extremes. Parameter VO Output Swing Test Conditions RL = 100 k RL = 2 k ISC Output Short Circuit Current Sourcing Sinking IS Supply Current LM6152AC Limit (2) LM6154BC LM6152BC Limit (2) Units 0.006 0.02 0.03 0.02 0.03 V max 4.992 4.97 4.96 4.97 4.96 V min 0.04 0.10 0.12 0.10 0.12 V max 4.89 4.80 4.70 4.80 4.70 V min 6.2 3 2.5 3 2.5 mA min 27 17 27 17 mA max 7 5 7 5 mA min 40 40 mA max 2 2.25 2 2.25 mA max Typ (1) 16.9 Per Amplifier 1.4 5.0V AC Electrical Characteristics Unless otherwise specified, all limits ensured for TJ = 25C, V+ = 5.0V, V- = 0V, VCM = VO = V+/2 and RL > 1 M to V+/2. Boldface limits apply at the temperature extremes. Parameter Test Conditions Typ (1) LM6154BC LM6152BC Limit (2) Units 24 15 24 15 V/s min SR Slew Rate 4V Step @ VS = 6V, RS < 1 k GBW Gain-Bandwidth Product f = 100 kHz 75 MHz Amp-to-Amp Isolation RL = 10 k 125 dB en Input-Referred Voltage Noise f = 1 kHz 9 nV/Hz in Input-Referred Current Noise f = 1 kHz 0.34 pA/Hz T.H.D Total Harmonic Distortion f = 100 kHz, RL = 10 k AV = -1, VO = 2.5 VPP -65 dBc ts Settling Time 2V Step to 0.01% 1.1 s (1) (2) 30 LM6152AC Limit (2) Typical Values represent the most likely parametric norm. All limits are specified by testing or statistical analysis. Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: LM6152 LM6154 3 LM6152, LM6154 SNOS752D - MAY 1999 - REVISED MARCH 2013 www.ti.com 2.7V DC Electrical Characteristics Unless otherwise specified, all limits are ensured for TJ = 25C, V+ = 2.7V, V- = 0V, VCM = VO = V+/2 and RL > 1 M to V+/2. Boldface limits apply at the temperature extremes. Parameter Test Conditions Typ (1) LM6152AC Limit (2) LM6154BC LM6152BC Limit (2) Units 2 5 5 8 mV max VOS Input Offset Voltage 0.8 TCVOS Input Offset Voltage Average Drift 10 V/C IB Input Bias Current 500 nA IOS Input Offset Current 50 nA RIN Input Resistance, CM 0V VCM 1.8V 30 M CMRR Common Mode Rejection Ratio 0V VCM 1.8V 88 0V VCM 2.7V 78 dB PSRR Power Supply Rejection Ratio 3V V+ 5V VCM Input Common-Mode Voltage Range Low -0.25 0 0 High 2.95 2.7 2.7 AV Large Signal Voltage Gain RL = 10 k 5.5 VO Output Swing RL = 10 k 0.032 0.07 0.11 0.07 0.11 V max 2.68 2.64 2.62 2.64 2.62 V min IS (1) (2) Supply Current Per Amplifier 69 dB V V V/mV 1.35 mA Typical Values represent the most likely parametric norm. All limits are specified by testing or statistical analysis. 2.7V AC Electrical Characteristics Unless otherwise specified, all limits are ensured for TJ = 25C, V+ = 2.7V, V- = 0V, VCM = VO = V+/2 and RL > 1 M to V+/2. Boldface limits apply at the temperature extremes. Parameter GBW (1) (2) 4 Gain-Bandwidth Product Test Conditions f = 100 kHz Typ 80 (1) LM6152AC Limit (2) LM6154BC LM6152BC Limit (2) Units MHz Typical Values represent the most likely parametric norm. All limits are specified by testing or statistical analysis. Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: LM6152 LM6154 LM6152, LM6154 www.ti.com SNOS752D - MAY 1999 - REVISED MARCH 2013 24V DC Electrical Characteristics Unless otherwise specified, all limits are ensured for TJ = 25C, V+ = 24V, V- = 0V, VCM = VO = V+/2 and RL > 1 M to V+/2. Boldface limits apply at the temperature extremes. Parameter Test Conditions Typ (1) LM6152AC Limit (2) LM6154BC LM6152BC Limit (2) Units 2 4 7 9 mV max VOS Input Offset Voltage 0.3 TCVOS Input Offset Voltage Average Drift 10 V/C IB Input Bias Current 500 nA IOS Input Offset Current 32 nA RIN Input Resistance, CM 0V VCM 23V 60 Meg CMRR Common Mode Rejection Ratio 0V VCM 23V 94 0V VCM 24V 84 dB PSRR Power Supply Rejection Ratio 0V VCM 24V VCM Input Common-Mode Voltage Range Low -0.25 0 0 High 24.25 24 24 AV Large Signal Voltage Gain RL = 10 k 55 VO Output Swing RL = 10 k 0.044 0.075 0.090 0.075 0.090 V max 23.91 23.8 23.7 23.8 23.7 V min 1.6 2.25 2.50 2.25 2.50 mA max IS (1) (2) Supply Current Per Amplifier 95 dB V V V/mV Typical Values represent the most likely parametric norm. All limits are specified by testing or statistical analysis. 24V AC Electrical Characteristics Unless otherwise specified, all limits are ensured for TJ = 25C, V+ = 24V, V- = 0V, VCM = VO = V+/2 and RL > 1 M to V+/2. Boldface limits apply at the temperature extremes. Parameter GBW (1) (2) Gain-Bandwidth Product Test Conditions f = 100 kHz Typ 80 (1) LM6152AC Limit (2) LM6154BC LM6152BC Limit (2) Units MHz Typical Values represent the most likely parametric norm. All limits are specified by testing or statistical analysis. Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: LM6152 LM6154 5 LM6152, LM6154 SNOS752D - MAY 1999 - REVISED MARCH 2013 www.ti.com Typical Performance Characteristics 6 Supply Current vs. Supply Voltage Offset Voltage vs. Supply voltage Figure 3. Figure 4. Bias Current vs. Supply voltage Bias Current vs. VCM Figure 5. Figure 6. Bias Current vs. VCM Bias Current vs. VCM Figure 7. Figure 8. Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: LM6152 LM6154 LM6152, LM6154 www.ti.com SNOS752D - MAY 1999 - REVISED MARCH 2013 Typical Performance Characteristics (continued) Output Voltage vs. Source Current Output Voltage vs. Source Current Figure 9. Figure 10. Output Voltage vs. Source Current Output Voltage vs. Sink Current Figure 11. Figure 12. Output Voltage vs. Sink Current Output Voltage vs. Sink Current Figure 13. Figure 14. Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: LM6152 LM6154 7 LM6152, LM6154 SNOS752D - MAY 1999 - REVISED MARCH 2013 www.ti.com Typical Performance Characteristics (continued) 8 Crosstalk (dB) vs. Frequency GBWP (@ 100 kHz) vs. Supply Voltage Figure 15. Figure 16. Unity Gain Frequency vs. Supply Voltage for Various Loads CMRR Figure 17. Figure 18. Voltage Swing vs. Frequency (CL = 100 pF) PSRR vs. Frequency Figure 19. Figure 20. Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: LM6152 LM6154 LM6152, LM6154 www.ti.com SNOS752D - MAY 1999 - REVISED MARCH 2013 Typical Performance Characteristics (continued) Open Loop Gain/Phase (VS = 5V) Open Loop Gain/Phase (VS = 10V) Figure 21. Figure 22. Open Loop Gain/Phase (VS = 24V) Noise Voltage vs. Frequency Figure 23. Figure 24. Noise Current vs. Frequency Voltage Error vs. Settle Time Figure 25. Figure 26. Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: LM6152 LM6154 9 LM6152, LM6154 SNOS752D - MAY 1999 - REVISED MARCH 2013 www.ti.com Typical Performance Characteristics (continued) Distortion vs. Frequency 0 HD (dBc) -10 VS = 5V AV = -1 -20 VIN = 5 VPP -30 RL = 10 k: THD HD2 -40 -50 -60 -70 -80 -90 HD3 -100 100k 1M FREQUENCY (Hz) Figure 27. 10 Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: LM6152 LM6154 LM6152, LM6154 www.ti.com SNOS752D - MAY 1999 - REVISED MARCH 2013 APPLICATION INFORMATION The LM6152/LM6154 is ideally suited for operation with about 10 k (Feedback Resistor, RF) between the output and the negative input terminal. With RF set to this value, for most applications requiring a close loop gain of 10 or less, an additional small compensation capacitor (CF) (see Figure 28) is recommended across RF in order to achieve a reasonable overshoot (10%) at the output by compensating for stray capacitance across the inputs. The optimum value for CF can best be established experimentally with a trimmer cap in place since its value is dependant on the supply voltage, output driving load, and the operating gain. Below, some typical values used in an inverting configuration and driving a 10 k load have been tabulated for reference: Table 1. Typical BW (-3 dB) at Various Supply Voltage and Gains VS Volts Gain CF pF -1 5.6 4 3 -10 6.8 1.97 -100 None 0.797 6.6 24 BW (-3 dB) MHz -1 2.2 -10 4.7 2.2 -100 None 0.962 In the non-inverting configuration, the LM6152/LM6154 can be used for closed loop gains of +2 and above. In this case, also, the compensation capacitor (CF) is recommended across RF (= 10 k) for gains of 10 or less. Figure 28. Typical Inverting Gain Circuit AV = -1 Because of the unique structure of this amplifier, when used at low closed loop gains, the realizable BW will be much less than the GBW product would suggest. The LM6152/LM6154 brings a new level of ease of use to op amp system design. The greater than rail-to-rail input voltage range eliminates concern over exceeding the common-mode voltage range. The rail-to-rail output swing provides the maximum possible dynamic range at the output. This is particularly important when operating on low supply voltages. The high gain-bandwidth with low supply current opens new battery powered applications where higher power consumption previously reduced battery life to unacceptable levels. The ability to drive large capacitive loads without oscillating functional removes this common problem. To take advantage of these features, some ideas should be kept in mind. The LM6152/LM6154, capacitive loads do not lead to oscillations, in all but the most extreme conditions, but they will result in reduced bandwidth. They also cause increased settling time. Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: LM6152 LM6154 11 LM6152, LM6154 SNOS752D - MAY 1999 - REVISED MARCH 2013 www.ti.com Unlike most bipolar op amps, the unique phase reversal prevention/speed-up circuit in the input stage, causes the slew rate to be very much a function of the input pulse amplitude. This results in a 10 to 1 increase in slew rate when the differential input signal increases. Large fast pulses will raise the slew-rate to more than 30 V/s. Figure 29. Slew Rate vs. VDIFF The speed-up action adds stability to the system when driving large capacitive loads. A conventional op amp exhibits a fixed maximum slew-rate even though the differential input voltage rises due to the lagging output voltage. In the LM6152/LM6154, increasing lag causes the differential input voltage to increase but as it does, the increased slew-rate keeps the output following the input much better. This effectively reduces phase lag. As a result, the LM6152/LM6154 can drive capacitive loads as large as 470 pF at gain of 2 and above, and not oscillate. Capacitive loads decrease the phase margin of all op amps. This can lead to overshoot, ringing and oscillation. This is caused by the output resistance of the amplifier and the load capacitance forming an R-C phase shift network. The LM6152/6154 senses this phase shift and partly compensates for this effect. 12 Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: LM6152 LM6154 LM6152, LM6154 www.ti.com SNOS752D - MAY 1999 - REVISED MARCH 2013 REVISION HISTORY Changes from Revision C (March 2013) to Revision D * Page Changed layout of National Data Sheet to TI format .......................................................................................................... 12 Submit Documentation Feedback Copyright (c) 1999-2013, Texas Instruments Incorporated Product Folder Links: LM6152 LM6154 13 PACKAGE OPTION ADDENDUM www.ti.com 1-Nov-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) LM6152ACM NRND SOIC D 8 95 TBD Call TI Call TI 0 to 70 LM61 52ACM LM6152ACM/NOPB ACTIVE SOIC D 8 95 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 70 LM61 52ACM LM6152ACMX NRND SOIC D 8 2500 TBD Call TI Call TI 0 to 70 LM61 52ACM LM6152ACMX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 70 LM61 52ACM LM6152BCM/NOPB ACTIVE SOIC D 8 95 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 70 LM61 52BCM LM6152BCMX NRND SOIC D 8 2500 TBD Call TI Call TI 0 to 70 LM61 52BCM LM6152BCMX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 70 LM61 52BCM LM6154BCM NRND SOIC D 14 55 TBD Call TI Call TI 0 to 70 LM6154BCM LM6154BCM/NOPB ACTIVE SOIC D 14 55 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 70 LM6154BCM LM6154BCMX/NOPB ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM 0 to 70 LM6154BCM (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 1-Nov-2013 (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 23-Sep-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant LM6152ACMX SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1 LM6152ACMX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1 LM6152BCMX SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1 LM6152BCMX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1 LM6154BCMX/NOPB SOIC D 14 2500 330.0 16.4 6.5 9.35 2.3 8.0 16.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 23-Sep-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM6152ACMX SOIC D 8 2500 367.0 367.0 35.0 LM6152ACMX/NOPB SOIC D 8 2500 367.0 367.0 35.0 LM6152BCMX SOIC D 8 2500 367.0 367.0 35.0 LM6152BCMX/NOPB SOIC D 8 2500 367.0 367.0 35.0 LM6154BCMX/NOPB SOIC D 14 2500 367.0 367.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2013, Texas Instruments Incorporated