Evaluates: MAX2831 MAX2831 Evaluation Kit General Description The MAX2831 evaluation kit (EV kit) simplifies testing of the MAX2831 receive and transmit performance in 802.11g/b applications operating in the 2.4GHz to 2.5GHz ISM band. The EV kit provides 50 SMA connectors for all RF and baseband inputs and outputs. Differential-tosingle-ended and single-ended-to-differential line drivers are provided to convert the differential I/Q baseband inputs and outputs to single ended. Features On-Board Line Driver and Voltage Reference 50 SMA Connectors on All RF and Baseband Ports PC Control Software Available at www.maximintegrated.com Quick Start The MAX2831 EV kit is fully assembled and factory tested. Follow the instructions in the Connections and Setup section to test the devices. Test Equipment Required This section lists the recommended test equipment to verify the operation of the MAX2831. It is intended as a guide only and substitutions may be possible: MAX2831 EV kit INTF3000+ interface board DC supply capable of delivering +5V and 200mA of continuous current DC supply capable of delivering -5V and 200mA of continuous current DC supply capable of delivering +3.3V and 300mA of continuous current DC supply capable of delivering +2.85V and 200mA of continuous current One HP8648s or equivalent signal sources capable of generating 0dBm up to 3GHz 802.11b/g CW I/Q waveform generator HP8561E or equivalent RF spectrum analyzer with a minimum 100kHz to 3GHz frequency range TDS3012 or equivalent oscilloscope with 200MHz bandwidth PC laptop or tablet with Microsoft Windows XP(R), Windows(R) 7, 8 OS and a USB port USB-A male to USB-B male cable Windows and Windows XP are registered trademarks and registered service marks of Microsoft Corporation. 19-0816; Rev 3; 1/16 Connections and Setup This section provides step-by-step instructions for getting the EV kit up and running in all modes (see Figure 1 for EV kit connections): 1) Connect the PC to the INTF3000 interface board using the USB-A male to USB-B male cable. On INTF3000, remove jumper JU1 and connect a DC supply set to 3.3V to the VPULL connector. Connect the 25-pin connector of the INTF3000 (J4) directly to the 25-pin connector on the EV kit (J18). 2) With the power supply turned off, connect a +2.85V power supply to VREG (pin 1), VCCAUX, and a +3.3V power supply to VBAT. Connect the power-supply ground to the header labeled GND1 or GND2. 3) With the power supply turned off, connect a +5V power supply to the +5V test point and a -5V power supply to the -5V test point. Connect the power-supply ground to the header labeled GND1 or GND2. Connect all the power-supply grounds together. 4) Make sure the jumpers are installed in their default positions as shown in Figure 1. 5) Turn on the +3.3V power supply, followed by the +2.85V power supply, +5V power supply, and -5V power supply. 6) Install and run the MAX2831 control software, available for download here. Receive Mode 1) Set the RXTX jumper across pins 2-3 (RX) to enable the receiver and disable the transmitter. Set the ANTSEL jumper to its default position 2-3 (ANT1). 2) Set the signal generator to accurately deliver -100dBm at 2438MHz, at the SMA port (ANT1/RXRF) of MAX2831. Connect the output of signal generator to RXRF port of MAX2831. 3) On the Registers page of the EV kit software, set the register values to the recommended setting in the MAX2831 data sheet by clicking the "Defaults" and "Send All" buttons. 4) On the Entry page, confirm that the "Receive Mode" is set to "normal," "Baseband Filter Mode Control" is set to "RX," and the "RF frequency" is tuned to 2437MHz. Maximize the RX LNA and RX VGA Gain. 5) Connect the spectrum analyzer to either RXBBI or RXBBQ. Set the center frequency to 1MHz with a span MAX2831 Evaluation Kit Evaluates: MAX2831 of 500kHz. Other recommended spectrum analyzer settings are: Res BW of 1kHz and Ref Level of 10dB. 6) Turn on the RF signal source. The supply current draw should be approximately 70mA. The output CW tone at 1MHz should be approximately -2dBm. Transmit Mode 1) Set the RXTX jumper across pins 1-2 (TX) to enable the transmitter and disable the receiver. Keep the ANTSEL jumper at its default position 2-3 (ANT1). 2) Connect TXRF port to the spectrum analyzer. Set the center frequency of spectrum analyzer to 2437MHz and span to 10MHz. Other recommended spectrum analyzer settings are: Res BW of 3kHz, Attenuation of 30dB and Ref Level of 22dB. 3) Connect a 1MHz sinusoid to TXBBI and a 1MHz sinusoid with a 90 phase shift (or a cosine) to TXBBQ. Set the input amplitude of each channel to 100mVRMS. 4) On the Registers page of the EV kit software, set the register values to the recommended register setting listed in the MAX2831 data sheet by clicking the "Defaults" and "Send All" buttons. 5) On the Entry page, make sure that the "Transmitter Mode" is set to "normal," "Baseband Filter Mode Control" is set to "TX," and the "RF Frequency" is tuned to 2437MHz. Set the TX gain to maximum using the "TX VGA Gain" sliding bar. 6) Enable the output of the baseband signal sources. The supply current draw should be approximately 88mA. 7) The TX output power at 2438MHz should be approximately 21dBm. The LO leakage at 2437MHz should be -16dBm and unwanted sideband at 2436MHz should be -17dBm. Layout Considerations The EV kit can serve as a guide for board layout. Keep PCB trace lengths as short as possible to minimize parasitic inductance. Also, keep decoupling capacitors as close to the IC as possible with a direct connection to the ground plane. Power-Supply Layout To minimize coupling between different sections of the IC, use a star power-supply routing configuration with a large decoupling capacitor at a central VCC node. The VCC traces branch out from this node, each going to a separate VCC node in the circuit. Place a bypass capacitor as close as possible to each supply pin. This arrangement provides local decoupling at each VCC pin. Use at least one throughput per bypass capacitor for a low-inductance ground connection. Do not share the capacitor ground vias with any other branch. Note: CW signals can be replaced by modulated 802.11g/b signals. Table 1. Jumper Functions JUMPER RXTX ANTSEL TXBBBUF/RXBBBUF VREG VCCVCO www.maximintegrated.com SETTING FUNCTION Pins 2-3 Pins 1-2 Pins 2-3 Pins 1-2 Pins 2-3 Pins 1-2 Pins 2-3 Pins 1-2 Enable receive mode Enable transmit mode Default Enables the buffers Disables the buffers Short the jumper to provide voltage to the MAX2831 from the linear regulator (U10) Supply the VCCVCO from VREG Supply the VCCVCO from the linear regulator (U10) Maxim Integrated 2 MAX2831 Evaluation Kit Evaluates: MAX2831 Figure 1. MAX2831 EV Kit Connections www.maximintegrated.com Maxim Integrated 3 MAX2831 Evaluation Kit Evaluates: MAX2831 Component Suppliers SUPPLIER WEBSITE AVX Corp. www.avx.com Digi-Key Corp. www.digikey.com Johnson Components www.johnsoncomponents.com Murata Americas www.murata.com Texas Instruments Inc. www.ti.com Note: Indicate that you are using the MAX2831 when contacting these component suppliers. Component List, PCB Layout, and Schematic Ordering Information MAX2831 EV PCB Layout +Denotes a lead(Pb)-free and RoHS-compliant EV kit. MAX2831 EV BOM PART TYPE MAX2831EVKIT+ EV Kit MAX2831 EV Schematic www.maximintegrated.com Maxim Integrated 4 MAX2831 Evaluation Kit Evaluates: MAX2831 Revision History REVISION NUMBER REVISION DATE PAGES CHANGED 0 5/07 Initial release -- 1 11/14 Updated Quick Start section 3 2 11/15 Added more detailed description for TX and RX sections and added Figure 1. 1-4 3 1/16 Updated connectivity information of INTF3000 board 1-3 DESCRIPTION For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim Integrated's website at www.maximintegrated.com. Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent licenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc. (c) 2016 Maxim Integrated Products, Inc. 5 DESIGNATION QTY DESCRIPTION C1 1 33pF 5% capacitor (0402) Murata GRM1555C1H330J C3, C16, C70, C79, C81, C89 6 100pF 5% capacitors (0402) Murata GRM1555C1H101J C4 1 18pF 5% capacitor (0402) Murata GRM1555C1H180J C5, C7, C10, C11, C13, C17, C18, C21, C22, C29, C40, C42, C43, C45, C46, C50, C52, C54, C59, C60, C64, C67, C83, C86 24 100nF 10% capacitors (0402) Murata GRM155R61A104K C6, C9, C30, C41, C62, C73, C74, C75, C87, C88 10 0.01F 10% capacitors (0402) Murata GRM155R71C103K C8, C44, C48, C49, C71, C72, C77 0 Not installed, capacitors C12, C51, C53, C55, C63, C65, C66 7 10F 20% tantalum capacitors (R-case) AVX TAJR106M006 C61 1 10F 10% capacitor (1206) Murata GRM31CR60J106K C68, C69 2 1.5pF 0.25pF capacitors (0402) Murata GRM1555C1H1R5C C76 1 1000pF 10% capacitor (0402) Murata GRM155R71H102K C78 1 2200pF 10% capacitor (0402) Murata GRM155R71H222K C80 1 68pF 5% capacitor (0402) Murata GRM1555C1H680J C82 J17 J18 JPB1-JPB4, JPB6, JPB7, JPCSB, JPDIN, JPLD, JPRXHP, JPSCLK, JPSHDNB L1, L2, L7 1 0 1 10F 10% capacitor (0805) Murata GRM21BR60J106K Not installed DB25 right-angle male connector AMP 5747238-4 0 Not installed 0 LDO_IN, VREG 2 Not installed 1 x 2 headers Sullins PEC36SAAN R1, R2, R6, R10, R16, R17, R22, R27 8 75 1% resistors (0402) R3, R7, R18, R23 4 3.3k 5% resistors (0402) R4, R5, R21, R26 4 49.9 1% resistors (0402) R8, R9, R12, R13, R28, R29, R31, R32 8 0 1% resistors (0402) R11, R30, R38, R46, R50 0 Not installed, resistors R14 1 270 5% resistor (0402) R39, R45 2 100 1% resistors (0402) R43 1 1k 1% resistor (0402) R51 1 1.2k 5% resistor (0402) R52 1 750 5% resistor (0402) R53 1 10k 5% resistor (0402) T1 0 Not installed T2, T3 2 2.4GHz RF baluns Murata LDB212G4010C-001 U1, U5 2 Line drivers (16 SO) Maxim MAX4447ESE+ U2, U6 2 Line receivers (16 SO) Maxim MAX4444ESE+ U3 1 Low-dropout reference (3 SOT) Maxim MAX6061BEUR+ U4 1 Transceiver (48 TQFN) Maxim MAX2831ETM+ U8, U9 2 SN74LVTH244ADB TI SN74LVTH244ADBR U10 0 Not installed (optional) Maxim MAX8882EUTJJ+ Y1 1 40MHz crystal Kyocera CX3225SB40000H0WZK21 +5V, -5V, B1-B7, CSB, DIN, GND1, GND2, LD, RSSI, RXBBI+, RXBBI-, RXBBQ+, RXBBQ-, RXHP, SCLK, SHDNB, TPANTSEL, TPCLKOUT, TPRXTX, TPTUNE, TPTXCMIN, TXBBI+ TXBBI-, TXBBQ+, TXBBQ-, VBAT, VCCAUX 33 Test points Keystone 5000 CLKOUT, FREF, RXBBI, RXBBQ, RXRF, TXBBI, TXBBQ, TXRF 8 SMA edge-mount connectors, round Johnson 142-0701-801 VCCLNA, VCCPA1, VCCPA2, VCCPLL, VCCRXBB1, VCCRXBB2, VCCRXMX, VCCTXMX, VCCXTAL, VCC_DB, VCC_REF, VREG 0 Not installed -- 6 Shunts (ANTSEL, LDO_IN, RXBBBUF, RXTX, TXBBBUF, VCCVCO) Sullins SSC02SYAN -- PCB: MAX2830/1/2 EVALUATION KIT Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Maxim Integrated: MAX2831EVKIT+