WIRE MANAGEMENT PRODUCTS Power Distribution Blocks Base & Rail Mount Euro-MAG Series
Connectors PCB – Spring Clamp
®
MAGNUM
Single & Double Row
Filtered Connectors
Series A2000, LP2000 & CB2000
Single Row Terminal Blocks
SPECIFICATIONS
Rating: A2: 30A, 300V*
LP2: 30A, 150V*
CB2: 30A, 300V*
Center Spacing: .375” or 3/8” (9.52 mm)
Wire Range: #12-22 AWG CU
Screw Size: #6-32 zinc plated philslot
Torque Rating: 9 in-lb.
Base: Standoffs standard for easy flux washing
Distance Between Barriers: .32” (8.1 mm)
Recommended PCB Hole Diameter: .076” (1.93 mm)
Molded Material: Black, UL Rated 94V0 Thermoplastic
Breakdown Voltage: 3400V (A2 & LP2); 4100V (CB2).
Agency Information: UL/CSA; IEC Compliance;
CE Certified
*30A Rating achieved with a #10 copper wire crimped to a ring terminal.;
20A Rating without ring terminal.
MOUNTING BARRIER & BARRIER
ENDS MOUNTING ENDS
ONLY ENDS ONLY
A C B C
Poles Mount Ctrs. Length Pole Ctrs. Length
02 1.13 1.56 .38 .81
03 1.50 1.93 .75 1.18
04 1.88 2.30 1.13 1.56
05 2.25 2.68 1.50 1.93
06 2.63 3.06 1.88 2.31
07 3.00 3.43 2.25 2.68
08 3.38 3.81 2.63 3.06
09 3.75 4.18 3.00 3.43
10 4.13 4.56 3.38 3.81
11 4.50 4.93 3.75 4.18
12 4.88 5.31 4.13 4.56
13 5.25 5.69 4.50 4.93
14 5.63 6.06 4.88 5.31
15 6.00 6.43 5.25 5.68
16 6.38 6.81 5.63 6.06
17 6.75 7.18 6.00 6.43
18 7.13 7.56 6.38 6.81
19 7.50 7.93 6.75 7.18
20 7.88 8.31 7.13 7.56
21 8.25 8.68 7.50 7.93
22 8.63 9.06 7.88 8.31
23 9.00 9.43 8.25 8.68
24 9.38 9.81 8.63 9.06
25 9.75 10.18 9.00 9.43
26 10.13 10.56 9.38 9.81
27 10.50 10.93 9.75 10.18
28 10.88 11.31 10.13 10.55
29 11.25 11.68 10.50 10.93
30 11.63 12.05 10.88 11.31
31 11.25 11.68
32 11.63 12.05
* Dimensions in inches. To convert to millimeters, multiply by 25.4.
: 105°C (221°F) max., -40°C (-40°F) min.
LP202110
A20510807WR
CB20210507
Operating Temperature
A2000 & LP2000 Series
C
A Mount Centers
.65
(16.5)
B Pole Centers
.375
(9.53)
Mount End Barrier End
.40
(10.2)
.76 (19.3)
.565 (14.35)
on LP2000
.15
(3.8)
dia.
.02
(.5)
Mount End Barrier End
CB2000 Series .375
.19
.32
(8.1)
C
.70
(17.8)
.60
(15.2)
.02
(.5)
(9.53)
Mount End Barrier End
B Pole Centers
A Mount Centers
(4.8)
dia.
Mount End Barrier End
6
Euro-MAG Series Base & Rail Mount Power Distribution Blocks WIRE MANAGEMENT PRODUCTS
PCB – Spring Clamp Connectors
Series A2000 & LP2000
Single Row Terminal Blocks
Part Numbering System
Series Terminal Style Base/End Poles Screw Options Options
A 2
L P 2
Single & Double Row
Filtered Connectors
A2
- standard barrier
01
- handwired
0
- flat base/molded
02
to
32 Blank
- std. screw
AB
- angle mnt. options (pg 9)
LP2
- low profile
02
- printed circuit mount end
02
to
30
on mount
00
- screws shipped bulk
A1
to
A9
- .250” QC
barrier
03
- non feed-thru
1
- flat base/mnt. end end base
03
- stainless steel
B1
to
B9
- .187” QC
04
- wire wrap tail
2
- flat base/barrier end
04
- brass nickel plated
DR
- drilled right angle (pg 9)
05
- extended handwired
3
- insulator base/mnt. end
07
- steel SEMS
JA
,
JB
&
JC
- barrier jumpers
06
- handwired
4
- insulator base/ (not available
L1
to
L6
marking options (pg 22)
07
- extended pin barrier end with hardware options)
MP, MP8
&
MT
mounting plates (pg 9)
08
- printed circuit
5
- closed base/
09
- brass SEMS
OJ2
&
OJ4
- over barrier jumpers (not
09
- .250 QC short mount end nickel plated available w/covers)
10
- .187 QC
6
- closed base/ (not available with
RC
- retaining clips (pg 9)
14
- printed circuit molded mount end hardware options
)
R30
to
R77
- right angle bends (pg 9)
19
- .250 QC long
9
- insulator base/
CA
- captive screw
SO
- stand off insulators (pg 9)
molded mount end
03CA
- stainless steel captive
S1
- solder lug/flat
04CA
- brass captive
Base/End Note: 0, 6,
07CA
- SEMS captive
Covers
- (pg 23)
9 styles not available
with covers. 5 & 6
09CA
- brass SEMS captive
07WR
- steel SEMS wire ready
Styles only available
with 03 terminals. (not available on LP2)
.20
(5.1)
.062
(1.57)
.031
(.79)
.55
(14.0)
.062
(1.57)
.031
(.79)
Inches (Millimeters)
.55
(14.0)
.110
(2.79)
031
.79)
Terminal Styles
01
02 03 04
Handwired Printed Circuit Non Feed-Thru Wire Wrap Tail
.30
.66 (7.6)
(16.8)
.82
(20.8)
.17
(4.3)
.031
(.79)
.062
.031 .11
.031
(1.57)
.110 (.79) (2.79) .031 .062
(.79) (2.79) (.79) (1.57 )
05 06 07 08
Extended Handwired Handwired Extended Pin Printed Circuit
.40
(10.2)
(6.35)
.031
(.79)
.72
(18.3)
.31
(7.9)
.41
(10.4)
.33
(8.4)
.250
(6.35)
.031
(.79)
.42
(10.7)
.031 .062
.125
.250 (.79) (1.57)
.031 .187 (3.2)
(.79) (4.75)
09 10
14 19
.250 QC short .187 QC Printed Circuit .250 QC long
7
WIRE MANAGEMENT PRODUCTS Power Distribution Blocks Base & Rail Mount Euro-MAG Series
Connectors PCB – Spring Clamp
®
MAGNUM
Single & Double Row
Filtered Connectors
Series A2000 & LP2000
Single Row Terminal Blocks Continued
Screw Options
Standar
d
03 04 07 09 07WR
Zinc Plated Steel Stainless Steel Brass Steel SEMS Brass SEMS Wire Ready
Nickel Plated Nickel Plated (A2 only)
Inches (Millimeters)Hardware Options (Bulk ordering part numbers are in parentheses.)
Solder Lugs Jumpers Quick Connects
Blade Width A = .250” Blade Width B = .187”
.68 (17.3)
.84 (21.2)
.33 (8.4)
S1 JA OJ2 A1
& B1
A2
& B2
A3
& B3
(2S1) (JA2-XX) (2A1 & 2B1) (2A2 & 2B2) (2A3 & 2B3)
.33 (8.4)
JB OJ4 A4
& B4
A5
& B5
A6
& B6
(JB2-XX) (2A4 & 2B4) (2A5 & 2B5) (2A6 & 2B6)
.33 (8.4)
JC A7
& B7
A8
& B8
A9
& B9
(JC2-XX) (2A7 & 2B7) (2A8 & 2B8) (2A9 & 2B9)
Base/End Options
B
.150 dia. (3.8)
mounting holes (2)
.095
.40
(10.2)
B
B
.180 (4.57)
B
10.2)
.218 (5.54)
(2.4)
SECTION A–A SECTION B–B
0, 6 & 9
1, 3 & 5
Molded Mount End Mount End
8
.40
;
;
;
Euro-MAG Series Base & Rail Mount Power Distribution Blocks WIRE MANAGEMENT PRODUCTS
PCB – Spring Clamp Connectors
Series A2000 & LP2000
Single Row Terminal Blocks Continued
Mounting Options
Right Angle Bends (A2, LP2 only)
Right angle terminals are offered on the A2000 & LP2000 Series.
07
Terminal Bend Configurations
Configurations are defined in these dimensions: X = pin extension beyond the
block base; Z = length from block base to centerline of the terminal tip.
Standard bends consist of the X and Z dimensions shown in the chart.
Specify by adding the selected Bend Option Code to the terminal part no.
X
Z
.82
Bend Available
Option X Z w/insulator
Code (minimum) base
Bend Available R30 -.04 .55 Yes
Option X Z w/insulator R35 .01 .50 Yes
Code (minimum) base R36 .02 .49 Yes
R42 .08 .43 Yes
R46 .12 .39 Yes
R30 -.04 .28 No R50 .16 .35 No
R35 .01 .23 No R53 .19 .32 No
R36 .02 .22 No R66 .32 .19 No
R39 .05 .19 No R69 .35 .16 No
R42 .08 .16 No R75 .41 .10 No
R46 .12 .12 No R77 .43 .08 No
R48 .14 .10 No
04 Terminal Bend Configurations
X
Z
.55
R50 .16 .08 No
Dimensions in inches. To convert to millimeters, multiply by 25.4.
Angle Brackets (A2, LP2 only) Drilled Right Angle (A2, LP2 only)
;
;
.144 HOLE
w/.312 C' BORE
.375
.24
;
;
.32
.45
.15
.25
.04
Option AB
Option DR
Angle brackets enable block to be fastened Counterbored holes across mount ends of
at right angles to normal mount position. block enable fastening with two screws at
Bulk part no. 2AB. right angles to normal mount position.
Standoffs Retaining Clip
RETAINING CLIP
MOUNTING
PLATE MP
MP8
;
MT
Mounting Plates
.300
STANDOFF
Option SO
Single & Double Row
Filtered Connectors
Options MP
, MP8 & MT
MP Metal inserts with .150” dia. hole accept
Option RC
Standoff mounts are tubes molded to the Use on standoff tubes. Fit panels up to .125”
thick. Two clips for every five positions.
mounting positions. Available with insulator
#6 screw. MP8 Metal inserts with .187” dia.
hole accept #8-32 screw. MT Metal inserts bases only. Supplied unassembled. Bulk Part No. H541.
with tapped hole accept #6-32 screw.
9
WIRE MANAGEMENT PRODUCTS Power Distribution Blocks Base & Rail Mount Euro-MAG Series
Connectors PCB – Spring Clamp
.120
®
MAGNUM
Single & Double Row
Filtered Connectors
Series CB2000
Single Row Terminal Blocks
Part Numbering System
Series Terminal Style Base/End Poles Screws
CB2
- closed back
01
- handwired
02
- printed circuit
03
- non feed-thru
07
- extended pin
14
- printed circuit
22
- dual tail printed circuit
1
- mount end
2
- barrier end
02
to
32
02
to
30
on mount
end base
03
- stainless steel
04
- brass nickel plated
07
- steel SEMS
standard
09
- brass SEMS
nickel plated
CA
- captive screw
07CA
- SEMS captive
CB2
Options
AB
- angle mounting brackets (pg 11)
A7
to
A9
- .250” QC
B7
to
B9
- .187” QC
EB
- exit back terminals
EF
- exit front terminals
JA
,
JB
&
JC
- barrier jumpers
L1
to
L6
marking options (pg 22)
LT1
to
LT6
marking options (pg 22)
OJ2
&
OJ4
- over barrier jumpers
MP, MP8, MT
&
MT8
mtg. plates (pg 11)
S1
- solder lug/flat
Covers - (pg.23)
Inches (Millimeters)Terminal Styles
.40
(10.2)
.18
.19
(4.8 )
.0
(.
.18
(4.6)
.0
.045
.70
(17.8)
.18
.045
.125
(3.18)
.18
(.7
.0 (1.14) (1.14)
.0 (4.6)
(.7 .062 (.
(3.05) (1.57)
(4.6) (4.6)
.19
(4.9)
.045
(1.14) .03
(.79)
.81
(4.6)
.40
(10.2)
.43
(10.9)
01
02 03 07 14 22
Handwired Printed Circuit Non Feed-Thru Extended Pin Printed Circuit Dual Tail
Available on Mount Printred Circuit
End (1) only.
Screw Options
03 04 07 09
Stainless Steel Brass Steel SEMS Brass SEMS
Nickel Plated Zinc Plated Nickel Plated
* NOTE: Wire ready screws standard on all terminal styles.
CB2 T
erminal Exit Options Inches (Millimeters)
.255
(6.48)
Y
X
.18 X .18
(4.6) (4.6)
Exit Rear (std.) EF Exit Front EB Exit Back
10
;
;
;
;
;
Euro-MAG Series Base & Rail Mount Power Distribution Blocks WIRE MANAGEMENT PRODUCTS
PCB – Spring Clamp Connectors
Series CB2000
Single Row Terminal Blocks
Inches (Millimeters)Hardware Options (Bulk ordering part numbers are in parentheses.)
Solder Lugs Jumpers Quick Connects
Blade Width A = .250”. Blade Width B = .187”.
.68 (17.3)
.84 (21.2)
.33 (8.4)
S1 JA OJ2 A7
& B7 A8 & B8
A9
& B9
(2S1) (JA2-XX) (2A7 & 2B7) (2A8 & 2B8) (2A9 & 2B9)
.33 (8.4)
JB OJ4
(JB2-XX)
.33 (8.4)
JC
(JC2-XX)
Mounting Options Inches (Millimeters)
Right Angle Mounting Bracket
End Positions
usable
Exit Back (EB
Angle
#6 or #8
mounting
screw & nut
(Customer
supplied.)
) .24
Terminals (6.1)
(10.7)
;
;
Snap-in Angle Bracket Chassis
or PCB
A
A
.71
(18.0)
.45
(11.4)
.79
(20.1)
1.02
(25.8)
.42
Bracket
Mounts blocks on PC boards at a right angle.
Option AB
• Protects solder joints.
• Recommended for all EB (Exit Back) PCB terminal blocks.
• Bracket snaps securely on block (no hardware required).
• Minimum strip length (end positions are usable).
• Mount with #6-32 or #8-32 screws (not supplied).
Mounting Plates
MOUNTING
PLATE
;
Options MP, MP8, MT & MT8
MP
MP Metal inserts with .150” dia. hole accept #6 screw.
MP8
MP8 Metal inserts with .187” dia. hole accept #8-32 screw.
MT Metal inserts with tapped hole accept #6-32 screw.
MT8 Metal inserts with tapped hole accept #8-32 screw.
MT
MT8
Single & Double Row
Filtered Connectors
11
