10Gbps 300m Duplex LC XFP Transceiver
PXP96-8503M
Primus IT Limited
Page 1
10Gbps 300m Duplex LC XFP Transceiver
PXP96-8503M
Features
Supports 9.95Gb/s to 10.5Gb/s bit rates
Vertical Cavity Surface Emitting Laser at 850nm and PIN photo-detector
Maximum link length of 300m on MMF(OM3)
Duplex LC receptacle optical interface compliant
Hot pluggable
All-metal housing for superior EMI performance
RoHS6 compliant (lead free)
Power dissipation <1.5W
No Reference Clock required
Built-in digital diagnostic functions
Operating case temperature:
Commercial: -5°C to +70°C
Applications
10G Ethernet
10G Fiber Channel
Standards
Fully compliant to XFP MSA Rev.4.5
Compatible with IEEE802.3ae 2002
Description
It is a multi-purpose optical transceiver module for 10Gbit/s data transmission applications at 850nm. It is ideally
suited for datacom(belly-to-belly for high density applications) and storage area network(SAN/NAS) applications
based on the IEEE 802.3ae and Fibre Channel standards Designed for short range distances the transceiver
module comprises a transmitter with a vertical cavity surface emitting laser (VCSEL) and a receiver with a PIN
photodiode. Transmitter and receiver are separate within a wide temperature range of -5°C to +70°C and offers
optimum heat dissipation and excellent electromagnetic shielding thus enabling high port densities for 10GbE
systems.
10Gbps 300m Duplex LC XFP Transceiver
PXP96-8503M
Primus IT Limited
Page 2
Module Block Diagram
Absolute Maximum Ratings
Parameter
Symbol
Min.
Typical
Max.
Unit
Power Supply Voltage1
VCC3
0
3.6
V
Power Supply Voltage2
VCC5
0
6
V
Storage Temperature
Ts
-40
+85
C
Relative Humidity
RH
0
85
%
RX Input Average Power
Pmax
-
1.5
dBm
Recommended Operating Environment
Parameter
Symbol
Min.
Typical
Max.
Power Supply Voltage1
VCC3
3.13
3.3
3.46
Power Supply Voltage2
VCC5
4.75
5
5.25
Module Total Power
P
1.5
Operating Case Temperature
TC
-5
+70
Data Rate
9.9
10.5
10Gbps 300m Duplex LC XFP Transceiver
PXP96-8503M
Primus IT Limited
Page 3
Electrical Characteristics
Parameter
Symbol
Min.
Typical
Max.
Unit
Note
Transmitter Section
Input Differential Impedance
Rin
90
100
110
Ω
Differential Data Input Swing
Vin PP
120
820
mV
1
Transmit Disable Voltage
VD
VCC3 – 1.3
VCC3
V
Transmit Enable Voltage
VEN
Vee
Vee+ 0.8
V
Receiver Section
Differential Data Output Swing
Vout PP
340
850
mV
LOS Fault
Vlos fault
VCC3 – 0.5
VCC_host
V
2
LOS Normal
Vlos norm
Vee
Vee+0.5
V
2
Notes:
1. Connected directly to TX data input pins. AC coupling from pins into laser driver IC.
2. LOS is an open collector output. Should be pulled up with 4.7kΩ – 10kΩ on the host board. Normal
operation is logic 0; loss of signal is logic 1.
Optical Parameters
Parameter
Symbol
Min.
Typical
Max.
Unit
Note
Transmitter Section
Centre Wavelength
λc
840
860
nm
RMS Spectral Width
Δλrms
0.4
0.45
nm
Side Mode Suppression Ratio
SMSR
30
dB
Average Optical Power (avg.)
Pout
-6.5
-1
dBm
1
Laser Off Power
Poff
-
-
-30
dBm
Extinction Ratio
ER
3.5
5.5
-
dB
2
Relative Intensity Noise
RIN
-
-
-128
dB/Hz
Optical Rise/Fall Time
tr/ tf
-
50
ps
3
Optical Return Loss Tolerance
-
-
12
dB
Transmitter and Dispersion
Penalty
TDP
3.9
dB
Output Optical Eye
Compliant with IEEE802.3ae eye masks when filtered
2
Receiver Section
Receiver Center Wavelength
λc
840
860
nm
Receiver Sensitivity in OMA
Sen
-11.1
-1
dBm
4
Los Assert
LOSA
-25
-
-
dBm
Los Dessert
LOSD
-
-
-12
dBm
Los Hysteresis
LOSH
0.5
-
5
dB
Overload
Pin-max
-
-
-1
dBm
4
Receiver Reflectance
-
-
-12
dB
Receiver Power (damage)
-
-
1.5
dBm
10Gbps 300m Duplex LC XFP Transceiver
PXP96-8503M
Primus IT Limited
Page 4
Notes:
1. The optical power is launched into 50/125µm MMF.
2. Measured with a PRBS 231-1 test pattern @10.3125Gbps.
3. Unfiltered, 20-80%. Measured with a PRBS 231-1 test pattern @10.3125Gbps.
4. Measured with a PRBS 231-1 test pattern @10.3125Gbps, ER=5.5dB, BER <10-12.
Timing Characteristics
Parameter
Symbol
Min.
Typical
Max.
Unit
TX_Disable Assert Time
t_off
10
us
TX_Disable Negate Time
t_on
2
ms
Time to Initialize
t_init
300
ms
P_Down/RST Assert Delay
P_Down/RST_on
100
us
P-Down Reset Time
t_reset
10
us
RX_LOS Assert Delay
t_loss_on
100
us
RX_LOS Negate Delay
t_loss_off
100
us
Clock Frequency
fSCL
400
kHz
Digital Diagnostic Monitor Characteristics (DDM)
The following digital diagnostic characteristics are defined over the Recommended Operating Environment unless
otherwise specified. It is compliant to SFF8077i with internal calibration mode. For external calibration mode
please contact our sales stuff.
Parameter
Symbol
Min.
Max.
Unit
Temperature Monitor Absolute Error
DMI_Temp
-3
3
C
Laser Power Monitor Absolute Error
DMI_TX
-3
3
dB
RX Power Monitor Absolute Error
DMI_RX
-3
3
dB
Supply Voltage Monitor Absolute Error
DMI_VCC
-3%
3%
V
Bias Current Monitor Absolute Error
DMI_Ibias
-10%
10%
mA
Digital Diagnostic Memory Map (Compliant with SFF-8077i)
The transceivers provide serial ID memory contents and diagnostic information about the present operating
conditions by the 2-wire serial interface (SCL, SDA).
The diagnostic information with internal calibration or external calibration all are implemented, including received
power monitoring, transmitted power monitoring, bias current monitoring, supply voltage monitoring and
temperature monitoring.
The digital diagnostic memory map specific data field defines as following (For further information, please refer to
SFF-8077i).
10Gbps 300m Duplex LC XFP Transceiver
PXP96-8503M
Primus IT Limited
Page 5
Pin Definitions
10Gbps 300m Duplex LC XFP Transceiver
PXP96-8503M
Primus IT Limited
Page 6
Pin Descriptions
Pin
Logic
Symbol
Name/Description
Ref.
1
GND
Module Ground
1
2
VEE5
Optional –5.2V Power Supply – Not required
3
LVTTL-I
Mod-Desel
Module De-select; When held low allows the module to ,
respond to 2-wire serial interface commands
4
LVTTL-O
Interrupt
Interrupt (bar); Indicates presence of an important condition
which can be read over the serial 2-wire interface
2
5
LVTTL-I
TX_DIS
Transmitter Disable; Transmitter laser source turned off
6
VCC5
+5V Power Supply
7
GND
Module Ground
1
8
VCC3
+3.3V Power Supply
9
VCC3
+3.3V Power Supply
10
LVTTL-I
SCL
Serial 2-Wire Interface Clock
2
11
LVTTL-
I/O
SDA
Serial 2-Wire Interface Data Line
2
12
LVTTL-O
Mod_Abs
Module Absent; Indicates Module is not present. Grounded in
the Module.
2
13
LVTTL-O
Mod_NR
Module Not Ready;
2
14
LVTTL-O
RX_LOS
Receiver Loss of Signal Indicator
2
15
GND
Module Ground
1
16
GND
Module Ground
1
17
CML-O
RD-
Receiver Inverted Data Output
18
CML-O
RD+
Receiver Non-Inverted Data Output
19
GND
Module Ground
1
20
VCC2
+1.8V Power Supply – Not required
21
LVTTL-I
P_Down/RS
T
Power Down; When high, places the module in the low
power stand-by mode and on the falling edge of P_Down
initiates a module reset
Reset; The falling edge initiates a complete reset of the
module including the 2-wire serial interface, equivalent to a
power cycle.
22
VCC2
+1.8V Power Supply – Not required
23
GND
Module Ground
1
24
PECL-I
RefCLK+
Reference Clock Non-Inverted Input, AC coupled on the host
board – Not required
3
25
PECL-I
RefCLK-
Reference Clock Inverted Input, AC coupled on the host
board – Not required
3
26
GND
Module Ground
1
27
GND
Module Ground
1
28
CML-I
TD-
Transmitter Inverted Data Input
29
CML-I
TD+
Transmitter Non-Inverted Data Input
30
GND
Module Ground
1
Notes:
1. Module circuit ground is isolated from module chassis ground within the module.
2. It must be pulled up with 4.7k-10k ohms on host board to a voltage between 3.15V and 3.6V.
3. A Reference Clock input is not required.
10Gbps 300m Duplex LC XFP Transceiver
PXP96-8503M
Primus IT Limited
Page 7
Recommended Interface Circuit
Recommended Host Board Power Supply Circuit
Recommended High-speed Interface Circuit
10Gbps 300m Duplex LC XFP Transceiver
PXP96-8503M
Primus IT Limited
Page 8
Mechanical Dimensions
Ordering information
Part Number
Product Description
PXP96-8503M
850nm, 10Gbps, 300m, Duplex LC XFP Transceiver, -5ºC ~ +70ºC, With DDM.
References
1. 10 Gigabit Small Form Factor Pluggable Module (XFP) Multi-Source Agreement (MSA), Rev 4.5 – August 2005.
2. Telcordia GR-253-CORE Specifications.
3. “Diagnostic Monitoring Interface for Optical Transceivers” SFF-8077i.
4. IEEE802.3ae 2002.
Important Notice
Performance figures, data and any illustrative material provided in this data sheet are typical and must be
specifically confirmed in writing by PRIMUS IT before they become applicable to any particular order or contract.
In accordance with the PRIMUS IT policy of continuous improvement specifications may change without notice.
The publication of information in this data sheet does not imply freedom from patent or other protective rights of
PRIMUS IT or others. Further details are available from any PRIMUS IT sales representative.
Contact Information
PRIMUS IT LIMITED
1、HongKong：RM M4/F Continental Mansion 300 King's RD HK
2、Tel:+86 0755-25924025
3、Fax:+86 0755-25924051
4、Website：http://www.primus-it.com
5、Email：sales@primus-it.com