Previous Datasheet Index Next Data Sheet DISCRETE POWER DIODES and THYRISTORS DATA BOOK D-358 To Order Previous Datasheet Index Next Data Sheet Bulletin I25155/B ST330C..C SERIES PHASE CONTROL THYRISTORS Hockey Puk Version Features 720A Center amplifying gate Metal case with ceramic insulator International standard case TO-200AB (E-PUK) Typical Applications DC motor controls Controlled DC power supplies AC controllers case style TO-200AB (E-PUK) Major Ratings and Characteristics Parameters ST330C..C Units 720 A 55 C 1420 A 25 C @ 50Hz 9000 A @ 60Hz 9420 A @ 50Hz 405 KA2s @ 60Hz 370 KA2s IT(AV) @ Ths IT(RMS) @ Ths ITSM 2 I t V DRM /V RRM tq TJ typical 400 to 1600 V 100 s - 40 to 125 C D-359 To Order Previous Datasheet Index Next Data Sheet ST330C..C Series ELECTRICAL SPECIFICATIONS Voltage Ratings Voltage V DRM /V RRM , max. repetitive VRSM , maximum non- I DRM /I RRM max. Code peak and off-state voltage repetitive peak voltage @ TJ = TJ max V V mA 400 500 Type number 04 ST330C..C 08 800 900 12 1200 1300 14 1400 1500 16 1600 1700 50 On-state Conduction Parameter I T(AV) Max. average on-state current @ Heatsink temperature ST330C..C 720 (350) A 180 conduction, half sine wave 55 (75) C double side (single side) cooled I T(RMS) Max. RMS on-state current 1420 I TSM Max. peak, one-cycle 9000 non-repetitive surge current 9420 I2 t Maximum I2t for fusing Units Conditions DC @ 25C heatsink temperature double side cooled t = 10ms No voltage t = 8.3ms reapplied 7570 t = 10ms 100% VRRM 7920 t = 8.3ms reapplied Sinusoidal half wave, 405 t = 10ms No voltage Initial TJ = TJ max. t = 8.3ms reapplied t = 10ms 100% VRRM t = 8.3ms reapplied A 370 KA2s 287 262 I 2 t Maximum I2t for fusing V T(TO) 1 Low level value of threshold KA2s 4050 V (I > x IT(AV)),TJ = TJ max. 0.92 voltage rt1 Low level value of on-state (16.7% x x IT(AV) < I < x IT(AV)), TJ = TJ max. 0.58 slope resistance rt2 High level value of on-state t = 0.1 to 10ms, no voltage reapplied (16.7% x x IT(AV) < I < x IT(AV)), TJ = TJ max. 0.91 voltage V T(TO) 2 High level value of threshold 12 m (I > x IT(AV)),TJ = TJ max. 0.57 slope resistance V TM Max. on-state voltage 1.96 IH Maximum holding current 600 IL Typical latching current 1000 V mA 2222222222222 I = 1810A, TJ = TJ max, t = 10ms sine pulse pk p T J = 25C, anode supply 12V resistive load Switching Parameter di/dt Max. non-repetitive rate of rise of turned-on current t d Typical delay time ST330C..C 1000 Units Conditions A/s q Typical turn-off time r TJ = TJ max, anode voltage 80% VDRM Gate current 1A, di /dt = 1A/s g 1.0 s t Gate drive 20V, 20, t 1s 100 V = 0.67% VDRM, TJ = 25C d ITM = 550A, TJ = TJ max, di/dt = 40A/s, VR = 50V dv/dt = 20V/s, Gate 0V 100, t = 500s p D-360 To Order Previous Datasheet Index Next Data Sheet ST330C..C Series Fig. 3 - Current Ratings Characteristics Fig. 4 - Current Ratings Characteristics Fig. 6- On-state Power Loss Characteristics Fig. 5- On-state Power Loss Characteristics Fig. 8 - Maximum Non-Repetitive Surge Current Single and Double Side Cooled Fig. 7 - Maximum Non-Repetitive Surge Current Single and Double Side Cooled D-364 To Order Previous Datasheet Index Next Data Sheet ST330C..C Series Fig. 9 - On-state Voltage Drop Characteristics Fig. 10 - Thermal Impedance Z thJ-hs Characteristics Fig. 11 - Gate Characteristics D-365 To Order Previous Datasheet Index Next Data Sheet ST330C..C Series Blocking Parameter ST330C..C Units Conditions dv/dt Maximum critical rate of rise of off-state voltage 500 V/s TJ = TJ max. linear to 80% rated VDRM IRRM IDRM Max. peak reverse and off-state leakage current 50 mA TJ = TJ max, rated V DRM/V RRM applied Triggering Parameter PGM ST330C..C Maximum peak gate power PG(AV) Maximum average gate power 2.0 IGM Max. peak positive gate current 3.0 +VGM Maximum peak positive Maximum peak negative to trigger VGT DC gate voltage required to trigger IGD VGD TJ = TJ max, t 5ms V TJ = TJ max, t 5ms p p MAX. 200 - 100 200 50 - 2.5 - 1.8 3.0 1.1 - DC gate current not to trigger DC gate voltage not to trigger A 23 TYP. DC gate current required p TJ = TJ max, f = 50Hz, d% = 50 5.0 gate voltage IGT TJ = TJ max, t 5ms W 20 gate voltage -VGM Units Conditions 10.0 10 TJ = - 40C mA TJ = 25C TJ = 125C TJ = - 40C V TJ = 25C TJ = 125C mA 0.25 Max. required gate trigger/ current/ voltage are the lowest value which will trigger all units 12V anode-to-cathode applied V TJ = TJ max Max. gate current/voltage not to trigger is the max. value which will not trigger any unit with rated VDRM anode-to-cathode applied Thermal and Mechanical Specification Parameter ST330C..C TJ Max. operating temperature range -40 to 125 T Max. storage temperature range -40 to 150 stg RthJ-hs Max. thermal resistance, junction to heatsink RthC-hs Max. thermal resistance, Units C 0.09 DC operation single side cooled K/W 0.04 0.02 K/W case to heatsink 0.01 F Mounting force, 10% 9800 N (1000) (Kg) wt Approximate weight 83 g Case style Conditions DC operation double side cooled DC operation single side cooled DC operation double side cooled TO - 200AB (E-PUK) See Outline Table D-361 3333 To Order Previous Datasheet Index Next Data Sheet ST330C..C Series RthJ-hs Conduction (The following table shows the increment of thermal resistence RthJ-hs when devices operate at different conduction angles than DC) Sinusoidal conduction Rectangular conduction Single Side Double Side Single Side Double Side Conduction angle Units 180 0.012 0.011 0.008 0.007 120 0.014 0.012 0.014 0.013 90 0.017 0.015 0.019 0.017 60 0.025 0.022 0.026 0.023 30 0.043 0.036 0.043 0.037 Conditions TJ = TJ max. K/W 12 Ordering Information Table Device Code ST 33 0 C 16 C 1 1 2 3 4 5 6 7 8 1 - Thyristor 2 - Essential part number 3 - 0 = Converter grade 4 - C = Ceramic Puk 5 - Voltage code: Code x 100 = VRRM (See Voltage Rating Table) 6 - C = Puk Case TO-200AB (E-PUK) 7 - 0 = Eyelet terminals (Gate and Auxiliary Cathode Unsoldered Leads) 1 = Fast-on terminals (Gate and Auxiliary Cathode Unsoldered Leads) 2 = Eyelet terminals (Gate and Auxiliary Cathode Soldered Leads) 3 = Fast-on terminals (Gate and Auxiliary Cathode Soldered Leads) 8 - Critical dv/dt: None = 500V/sec (Standard selection) L = 1000V/sec (Special selection) D-362 To Order 2222222222222 Previous Datasheet Index Next Data Sheet ST330C..C Series Outline Table ANODE TO GATE CREEPAGE DISTANCE: 11.18 (0.44) MIN. STRIKE DISTANCE: 7.62 (0.30) MIN. 25.3 (0.99) 0.3 (0.01) MIN. DIA. MAX. 14.1 / 15.1 (0.56 / 0.59) 0.3 (0.01) MIN. 25.3 (0.99) GATE TERM. FOR 1.47 (0.06) DIA. PIN RECEPTACLE DIA. MAX. 40.5 (1.59) DIA. MAX. Case Style TO-200AB (E-PUK) All dimensions in millimeters (inches) 2 HOLES 3.56 (0.14) x 1.83 (0.07) MIN. DEEP 6.5 (0.26) 4.75 (0.19) 23 25 5 42 (1.65) MAX. 28 (1.10) Fig. 2 - Current Ratings Characteristics Fig. 1 - Current Ratings Characteristics D-363 3333 To Order