PT10MV10-103A2020-PM-S - AMPHENOL

Electrical rotation angle 2

Torque

Life3

rotational

stop 0.4 to 2 Ncm. (0.6 to 2.7 in-oz)

> 5 Ncm. (<7 in-oz)

Mechanical rotation angle 1235° ± 5°

220° ± 20°

up to 100K cycles

Range of values 1100 Rn 5M (Decad. 1.0 - 2.0 - 2.2 - 2.5 - 4.7 - 5.0)

Tolerance 1

Max. voltage

Nominal power 50ºC (122°F) 3

200 VDC (lin) 100 VDC (no lin)

± 20%

± 30%

0.15 W (lin) 0.07 W (no lin)

100 Rn 1M

1M Rn 5M

Taper Linear ; Log; Alog. (Log. & Alog. only Rn 1K)

Residual resistance

Equivalent noise resistance

0.5% Rn (5 min.)

3% Rn (3 min.)

Operating temperature 2,3 -25ºC to +70ºC (-13ºF to + 158ºF)

3 Others: check availability.

1 Others: check availability. 2 Up to 85°C depending on application.

3 For higher specifications please visit our PTC10 series.

1 360º version available: ST10 2 333º version available: ST10

For reflow soldering capable models please see our PS10 datasheet.

Automotive / Appliance control - sensor

Piher Sensing Systems

Our product competencies and services:

Potentiometers | Position / Angle sensors | Rotary switches | Incremental encoders

Printed circuit resistors | Mechatronics | Value added assemblies

Main features

• Carbon resistive element.

• Dust proof enclosure.

• Polyester substrate.

• Wiper positioned at initial, 50%

or fully clockwise.

Also upon request:

• Available in magazines for

automatic insertion.

• Long life model for low-cost

control potentiometer

applications.

• Self-extinguishable plastic UL

94V-0.

• Cut track option (open circuit).

• Special tapers.

• Mechanical detents.

• Low torque version.

• Special switch option.

• 3% Linearity and 100K cycles

mechanical life.

Description

Mechatronics

Electromechanical

Controls

Sensors

Mechanical specifications

Electrical specifications

The PT10 potentiometer offers

control where frequent

adjustment is required. The

shaftless design allows for

employment of different

engagement mechanisms, such

as a customized shaft, a motor

control or a human interface

adjustment.

This potentiometer can also

contr ol variabl e outputs including

frequency, change in motor speed

or volume.

Typical applications include test

and measurement equipment,

consumer electronics,

appliances, small engines,

robotics, motion c ontrollers, and

medical equipment control

panels.

This datasheet shows you the

basics of the PT10 potentiometer

that is quite versatil e and easy t o

taylor. Do not hesitate to contact

Piher for advice.

10 mm carbon potentiometer

PT10

-Page 1 of 10-

10 mm carbon potentiometer

PT10

505 = 5 M

(See note 9)

positive tolerance

Code:

Piher Sensing Systems

Our product competencies and services:

Potentiometers | Position / Angle sensors | Rotary switches | Incremental encoders

Printed circuit resistors | Mechatronics | Value added assemblies

Automotive / Appliance control - sensor

How to order Optional extras

Mechatronics

Electromechanical

Controls

Sensors

- = standard

L= Low torque

H01L

Rotors

(See note 1)

PT10

Series

101

Value

Taper

A = Lin.

B = Log.

C = Alog.

Detents

PackagingCut track

- = none

PCI = Initial

PCF = Final

Life

- = 1K cycles

E= 10K cycles

Shaft/rotor colour

AM = Yellow

AZ = Blue

BL = White

CR = Cream

GR = Grey

MA = Brown

NA = Orange

NE = Black

RO = Red

VE = Green

VI = Violet

Wiper position

- = Initial

PM = 50%

PF = Final

2020

Tolerance

0505 = ± 5%

0707 = ± 7%

1010 = ± 10%

2020 = ± 20%

3030 = ± 30%

Torque

- = none

PAI

PAM

PAF

P1I

P1F

P02

P16

000 = CM

101 = 100

504 = 500 K

inserted

shaft

Mounting

method

H01

H02

H05

H07

H10

V05

V10

V11

V13

(See note 2)

- - - - - - - -

inserted

knob

Standard default options

How to order examples

PT10LH01-103A2020-S

10mm potentiometer with rotor “L” (arrow shape), H01 mounting method

(horizontal adjustment), 10K value and 20% resistive tolerance.

Cut track No

Detents None

Packing Bulk

Non flammable No

Rotor colour White

haft colour Natural

(not coloured)

Wiper

send

position Initial

Torque

0.4 to 2 Ncm.

Life 1000 cycles

PT10WV05-104A1010-9-NE-S

10mm potentiometer with rotor W (factory pre-inserted shaft), V05

mounting method (vertical adjustment), 100K value,10% resistive

tolerance and black shaft.

Low Torque: 1 Ncm

No detent option available for low torque models.

(9)

If you wish to use your own custom plastic shaft/knob/actuator please contact Piher for advice about compatible materials.

(10)

(6) Magazines: not available with the H10, V05 and V13 models, nor with adjustment types X, W, Y, Z.

(7) Non flammable: housing, rotor and shaft. According to UL 94V-0

(5) Standard: 1000 cycles. Long life “E”: 10.000 cycles. Others: check availability..

Example: +7%

-5% 07 05 negative tolerance

(4) Other tolerances: check availability.

NOTES: (1) "Z" adjustment only available on "H" versions. Rotor "G" only available in purple color (shaft/rotor color code "VI").

(2) V05 & H07 terminals material: brass.

First two digits of the value.

Code:

Example: 10 1Numb of zeros

(3) Value 000 = CM = Switch version (contact us)

SMD versions available (PS10 series).

High and low ohmic values may not allow all tolerances: check availability.

Potentiometer without shaft: only rotor Potentiometer with shaft: only shaft

(8) Colour shaft/rotor:

Endles rotation version available (ST10).

-Page 2 of 10-

(See note 3)

(See note 7)

Flammability

- = standard

I =

Non flammable

(See note 8)

Shaft/Thum.

- = none

1 = Fig. 1

2 = Fig. 2

18 = Fig. 18

(See note 6)

- = bulk

T = magazines

(See note 10)

(See note 4)

(See note 5)

10 mm carbon potentiometer

PT10

V05

V13

Piher Sensing Systems

Our product competencies and services:

Potentiometers | Position / Angle sensors | Rotary switches | Incremental encoders

Printed circuit resistors | Mechatronics | Value added assemblies

Automotive / Appliance control - sensor

Mechatronics

Electromechanical

Controls

Sensors

Mounting methods. Dimensions

Rotors (Default delivery is at initial position. Wipers are shown positioned at 50% for the picture)

V = horizontal mounting – vertical adjustment H = vertical mounting – horizontal adjustment

A = Initial S = Wiper E = Final

4.8

63.5

+0.2

5 5

1.3+0.1

10.3

+0.1

3.5

+0.1

2.5

4.8

6.5 3.5

+0.2

2.5

1.3+0.1

10.3

+0.1

3.5

+0.1

2.5

V11

4.8

5 5

1.3

10.3

63.3

4.8

5 5

1.3

10.3

63.3

With knob/humbwheel inserted

= Adjustable from collector side (default knob is 5034).

= Adjustable from terminal side (default knob is 5034).

3.5

1.95

0.8

3.5 7

0.8

6.5

3.75

51.4º

1.7

W =

Adjustable from

terminal side

With inserted shaft.

All rotors are thru-hole.

Without shaft or knob.

0.7

2.2

K = Cross slot

2.1

0.8

L = Screwdriver

1.6

= Hexagonal

M = Hexagonal X =

Adjustable from

collector side

(50%)

INITIAL

V10

-Page 3 of 10-

Download 3D - STEP files here: https://piher.net/piher/?p=905

10 mm carbon potentiometer
PT10
H02
SMD versions (see PS10 datasheet)
V13
2
5
2
2
2.5 2.5
5.7
5.75
10.9
2.05
5.15
10.3
2.5 2.5
9.4
2.5
H07
2.5
H10
2.5
H01
H05
6
0.9-0.1
1.6
Detail
+0.3
-0.1
2.5
2.5
Piher Sensing Systems
Our product competencies and services:
Potentiometers | Position / Angle sensors | Rotary switches | Incremental encoders
Printed circuit resistors | Mechatronics | Value added assemblies
Automotive / Appliance control - sensor
Mechatronics
Electromechanical
Controls
Sensors
Mounting methods. Dimensions
+0.2
2.5
12.1
2.5
4.8
2.5
+0.2
10.3
+0.1
3.5
1
+0.1
7
+0.2
2.5
5
1.3
+0.1
AE
S
A = Initial S = Wiper E = Final
+0.1
2.5
+0.2
2.5
12.1
4.8+0.2
5
10.3
3.5
1
+0.1
7+0.2
5
5
1.3+0.1
+0.2
9.3
6+0.2
9.3
3.3 7
V = horizontal mounting – vertical adjustment H = vertical mounting – horizontal adjustment
2.5
12.1
10.3
1
7
4.8
2.5
5
2.5
1.3
2.5
10.7
10.3
3.5
1
3.8
5
1.3
4.5
3.8
10.3
4.8
3.8
5
2.6
2.5
12.1
3.5
1
7
3.8
3.5 7.7
3.3
2.5
12.1
4.8
5
10.3
1
7
5
5
1.3
3.3
check availability
Crimped terminals - detail
V11, V13, H02, H10 models feature “crimped” terminals that provide greater
stability during the soldering process.
-Page 4 of 10-

10 mm carbon potentiometer

PT10

Piher Sensing Systems

Our product competencies and services:

Potentiometers | Position / Angle sensors | Rotary switches | Incremental encoders

Printed circuit resistors | Mechatronics | Value added assemblies

Automotive / Appliance control - sensor

Mechatronics

Electromechanical

Controls

Sensors

Standard values - tolerances

Detents

Standard mechanical life is 500

cycles.

Long life versions are available

under request and have the

following characteristics at Tª:

- Potentiometers with 1 to 3

detents: up to 10K cycles

- Potentiometers with 4 and mor e

detents: up to 5K cycles

Please consult y our neares t Piher

supplier if unique non-

overlapping values at each detent

position or LOG/ALOG tapers are

required.

Different output voltage values

can be matched at each detent

position (see next page).

Detent torque can vary from 1.2

to 2.5 times the standard

potentiometer torque.

For V05 mounting: check

availability.

For mor e than 16 detents versions

please contact your nearest

PIHER authorised distributor.

For custom voltage outputs in any detent position see page 6.

Relative detent positions

along the total mechanic al

travel.

Unles s otherwise specified

the detents are evenly

spaced (using the end

points

as reference)

Detents detail.

(7 detents

example)

Special custom taper example.

(contact at sales@piher.net)

100% Rn

A = Linear

B = Log.

C = Alog.

Standard

Tapers

R 2 + 5%

P07

P06

P08 P10

P09

P16

4.8

10.3

39º

P13

P11

P12

-Page 5 of 10-

P02P1FP1i

P05

P04

P03

PAM

PID

A= 26º

B= 27.5º

PFD

PAI

Wiper

position

PAF

Wiper

position

(wiper positioned at initial) (wiper positioned at final)

Resistance 100 200 220 250 470 500 1K 2K 2.2K 2.5K 4.7K 5K 10K 20K 22K 25K 47K 50K 100K 200K 220K 250K 470K 500K 1M 2M 2.5M 4.7M 5M

How to order code 101 201 221 251 471 501 102 202 222 252 472 502 103 203 223 253 473 503 104 204 224 254 474 504 105 205 255 475 505

Standard tolerance 20% 30%

10 mm carbon potentiometer

PT10

Constant value zones can be combined with strategically located stops matching the flat areas of the output.

If you require this feature, please, send us your requirements to sales@piher.net

Piher Sensing Systems

Our product competencies and services:

Potentiometers | Position / Angle sensors | Rotary switches | Incremental encoders

Printed circuit resistors | Mechatronics | Value added assemblies

Automotive / Appliance control - sensor

Stepped outputs Stepped outputs

Mechatronics

Electromechanical

Controls

Sensors

PIHER’s potentiometers can

feature special stepped outputs

or ‘constant voltage zones’ for

the 10mm and 15mm product

families.

These constant voltage zones

can be combined with PIHER’s

mechanical detents to provide

exact alignment between the

electrical output (flat areas)

and the mechanical detent

position. The result is a higher

level of precision in controlling

lighting, temperature, motor or

other electronic control

systems.

In addition to established

catalogue detent

configurations, we will design

and manufacture any other

configuration on our tried-and-

tested carbon/cermet &

THM/SMD potentiometer

technology and processes.

With its precise control

capabilities, our 10mm and

15mm potentiometers series

are well suited for many

consumer applications such as

lighting (dimmers), power hand

tools, relays, timers and HVAC

systems.

100%

0º 234º

SA E

By combining the constant value zones with the detents, engineers

can align the same voltage values with each of the detent stops

when rotating the control both forward and backward.

This provides clear mechanical positions that are not only repeatable,

but perfectly aligned electrical outputs at each of the (detent) angles.

Piher’s detents also prevent output values from changing due to

vibration or accidental rotor movements, furthering reliable control

consistency.

Wiper position

456

110

when the potentiometer’s wiper position is located at detent

nº9, the output votage will be 88.9% Un ± % tolerance.

Improved repeatability

Stepped output s version example (10 step s version):

Unique, non-overlapping values at each stop (detent position)

It prevents changes in the output value due to light vibration or accidental rotor micro-movements

Fully customisable according to customer´s needs

Cost effective replacement for absolute encoders

Main advantages

Absolute encoders can easily be

replaced connecting the potentiometer to

the microprocessor’s

analogue input.

Design tip. Cost-effectiveness

A== = = = = ===

88.9% Un

77.7% Un

66.6% Un

55.5% Un

44.4% Un

33.3% Un

22.2% Un

11.1% Un

0% Un / 0º

100% Un

50%

2 3 4 5 6 7 8 9

110

-Page 6 of 10-

10 mm carbon potentiometer

PT10

25.5

3.7

10.4

Piher Sensing Systems

Our product competencies and services:

Potentiometers | Position / Angle sensors | Rotary switches | Incremental encoders

Printed circuit resistors | Mechatronics | Value added assemblies

Automotive / Appliance control - sensor

Shafts

Mechatronics

Electromechanical

Controls

Sensors

4.9

15.2

Fig. 12 / Ref. 6052 Fig. 14 / Ref. 5055

4.5

3.3

For G and M rotor types, top view.

4.9

Fig. 7 / Ref. 5115

15.2

4.9

Fig. 8 / Ref. 5116

25.5

4.9

Fig. 9 / Ref. 5119

12.5

Fig. 10 / Ref. 5120

4.9

3.1

2.6

8.1

8.4

-Page 7 of 10-

Fig. 2 / Ref. 5053 Fig. 3 / Ref. 5012 Fig. 6 / Ref. 5035Fig. 1 / Ref. 5016 Fig. 4 / Ref. 6053

10 mm carbon potentiometer

PT10

Mechatronics

Electromechanical

Controls

Sensors

Piher Sensing Systems

Our product competencies and services:

Potentiometers | Position / Angle sensors | Rotary switches | Incremental encoders

Printed circuit resistors | Mechatronics | Value added assemblies

Automotive / Appliance control - sensor

By default, shafts, knobs &

thumweels are delivered

unassembled.

Mounted shafts, knobs &

thumbweels can be delivered at

specific positions (a drawing must

be provided by the customer).

If you need the shaft or knob to

be deliver ed as sembl ed from the

factory, please select the

appropriate rotor in the part

number: X, W, Y or Z.

The plastic col or c an be st ated in

the part number. Non flammable

plastic can be ordered too.

If the potentiometer is ordered

with non flamable plastic

materials (UL 94V0) then the shaft

or knob will be deliver ed with non

flamable plastic too.

If you wish to use your own plas tic

shaft/knob/actuator, please,

contact Piher for advice about

compatible materials.

Knobs/thumbwheels

For G and M rotor types, top view.

Fig. 5 / Ref. 5034

11.5

Fig. 17 / Ref. 5062

21 1.5

Fig. 15 / Ref. 6008

9.5

Fig. 16 / Ref. 5039

Fig. 18 / Ref. 6064 Upon request.

2- GANG Plastic Knob/ Plastic Shaft

INITIAL

CCW

P.F.

FINAL

P.M.

50% +

15º

Positioning

Std. Position = CCW. Other delivery positions upon request.

-Page 8 of 10-

Numbered Thumbweel

19 1

Marking: configurable number of positions

Example of four positions marking pictured

For R rotor type only

2.5

Ø1.3

Ø6

12.75