Embedded Power for Business-Critical Continuity Rev.3.12.09_170 PTH12060 of 6 PTH12060 12 Vin Total Power: 55 Watts # of Outputs: Single Special Features * 10 A output current * 12 V input voltage * Wide-output voltage adjust 1.2 Vdc - 5.5 Vdc for suffix `W' & 0.8 Vdc - 1.8 Vdc for suffix `L' * Auto-trackTM sequencing* * Margin up/down controls * Efficiencies up to 94% * Output ON/OFF inhibit * Output voltage sense * Point-of-Load-Alliance (POLA) compatible * Available RoHS compliant * 2 Year Warranty Specifications Input Input voltage range: (See Note 3, page 3) 10.8 - 13.2 Vdc Input current: No load 10 mA typ. Remote ON/OFF: (See Note 1, page 3) Positive logic Start-up time: 1 V/ms Undervoltage lockout: 9.0 - 9.5 V typ. Track input voltage: Pin 8 (See Note 6, page 3) 0.3 Vin All specifications are typical at nominal input, full load at 25C unless otherwise stated. Cin = 560 F, Cout = 0 F Safety * UL/cUL CAN/CSA-C22.2 No. 60950-1-03/UL 60950-1, File No. E174104 * TUV Product Service (EN60950) Certificate No. B 04 06 38572 044 * CB Report and Certificate to IEC60950, Certificate No. US/8292/UL *Auto-trackTM is a trade mark of Texas Instruments Embedded Power for Business-Critical Continuity Rev.3.12.09_170 PTH12060 of 6 Specifications Continued Output Voltage adjustability: (See Note 4, page 3) Suffix `W' Suffix `L' 1.2 - 5.5 Vdc 0.8 - 1.8 Vdc Setpoint accuracy: 2.0% Vo Line regulation: 10 mV typ. Load regulation: 12 mV typ. Total regulation: 3.0% Vo Minimum load: 0A Ripple and noise: 20 MHz bandwidth (See Note 8, page 3) Temperature co-efficient: Transient response: Suffix `W' Vo 2.5 V Vo > 2.5 V Suffix `L' Vo 1.0 V Vo > 1.0 V 25 mV pk-pk 1% Vo -40 C to +85 C 0.5% Vo (See Note 5, page 3) 70 s recovery time Overshoot/undershoot 100 mV Margin adjustment: 20 mV pk-pk 30 mV pk-pk 5.0% Vo EMC Characteristics Electrostatic discharge: EN61000-4-2, IEC801-2 Conducted immunity: EN61000-4-6 Radiated immunity: EN61000-4-3 General Specifications Efficiency: See tables on page 3 Insulation voltage: Switching frequency: Over Vin and Io ranges Non-isolated Suffix `W' Suffix `L' 350 kHz typ. 250 kHz typ. Approvals and standards: EN60950 UL/cUL60950 Material flammability: UL94V-0 Dimensions: (L x W x H) Weight: MTBF: 25.27 x 15.75 x 9.00 mm 0.995 x 0.620 x 0.354 in 5 g (0.18 oz) Telcordia SR-332 7,092,000 hours Thermal Performance: (See Note 2, page 3) Operating ambient, temperature Non-operating -40 C to +85 C -40 C to +125 C MSL (`Z' suffix only): JEDEC J-STD-020C Level 3 Auto reset 20 A typ. Environmental Specifications Protection Short-circuit: Embedded Power for Business-Critical Continuity Rev.3.12.09_170 PTH12060 of 6 Ordering Information Output Power (max) Input Voltage Output Voltage 55 W 10.8 - 13.2 Vdc 55 W 10.8 - 13.2 Vdc Output Currents Min Max Efficiency (max) 0.8 - 1.8 Vdc 0A 10 A 88% 10 mV 12 mV PTH12060L 1.2 - 5.5 Vdc 0A 10 A 94% 10 mV 12 mV PTH12060W Part Number System with Options Regulation Line Load M odel Numbers PTH12060WAST Product Family Point of Load Alliance Compatible Input Voltage 12 = 12 V Output Current 06 = 10 A Mechanical Package Always 0 Packaging Options No Suffix = Trays T = Tape and Reel (7) Mounting Option (8) D = Horizontal Through-Hole (RoHS 6/6) H = Horizontal Through-Hole (RoHS 5/6) S = Surface-Mount Solder Ball (RoHS 5/6) Z = Surface-Mount Solder Ball (RoHS 6/6) Pin Option A = Through-Hole Std. Pin Length (0.140") A = Surface-Mount Tin/Lead Solder Ball Output Voltage Code W = Wide L = Low Voltage Output Voltage Adjustment of the PTH12060 Series The ultra-wide output voltage trim range offers major advantages to users who select the PTH12060. It is no longer necessary to purchase a variety of modules in order to cover different output voltages. The output voltage can be trimmed in a range of 1.2 Vdc to 5.5 Vdc for suffix `W' and 0.8 Vdc to 1.8 Vdc for suffix `L'. When the PTH12060 converter leaves the factory the output has been adjusted to the default voltage of 1.2 V for the PTH12060W and 0.8 V for the PTH12060L. Notes Efficiency Table - PTH12060W (Io = 8 a) 1 Output Voltage Efficiency Vo = 5.0 V 94% Vo = 3.3 V 92% Vo = 2.5 V 90% Vo = 2.0 V 88% Vo = 1.8 V 87% Vo = 1.5 V 85% Vo = 1.2 V 83% 2 3 4 5 6 7 8 9 Remote ON/OFF. Active High ON: Pin 3 open; or V > Vin - 0.5 V OFF: Pin 3 GND; or V < 0.8 V (min - 0.2 V). See Figures 1, 2 and 3 for safe operating curves of PTH12060W and Figures 6, 7 and 8 for safe operating curves of PTH12060L. A 560 F electrolytic input capacitor is required for proper operation. The capacitor must be rated for a minimum of 800 mA rms of ripple current. An external output capacitor is not required for basic operation. Adding 330 F of distributed capacitance at the load will improve the transient response. 1 A/s load step, 50 to 100% Iomax, Cout = 330 F. If utilized Vout will track applied voltage by 0.3 V (up to Vo set point). Tape and reel packaging only available on the surface-mount versions. The pk-pk output ripple voltage is measured with an external 10 F ceramic capacitor. See Figures 5 and 8 for Standard application schematic. To order Pb-free (RoHS compatible) surface-mount parts replace the mounting option `S' with `Z', e.g. PTH12060WAZ. To order Pb-free (RoHS compatible) through-hole parts replace the mounting option `H' with `D', e.g. PTH12060WAD. Efficiency Table - PTH12060L (Io = 8 a) Output Voltage Efficiency Vo = 1.8 V 88% Vo = 1.5 V 87% Vo = 1.2 V 84% Vo = 1.0 V 82% Vo = 0.8 V 79% Embedded Power for Business-Critical Continuity Rev.3.12.09_170 PTH12060 of 6 90 90 80 80 TEMPERATURE (C) TEMPERATURE (C) PTH12060W Characteristic Data 70 60 Nat Conv 100 LFM 200 LFM 400 LFM 50 40 70 60 40 30 20 Nat Conv 100 LFM 200 LFM 400 LFM 50 30 0 2 4 6 8 20 10 0 2 OUTPUT CURRENT (A) 4 6 8 10 OUTPUT CURRENT (A) Figure 2 - Safe Operating Area Vin = 12 V, Output Voltage = 3.3 V (See Note A) Figure 1 - Safe Operating Area Vin = 12 V, Output Voltage = 5 V (See Note A) 100 80 90 70 60 EFFICIENCY (%) TEMPERATURE (C) 90 Nat Conv 100 LFM 200 LFM 400 LFM 50 40 30 20 80 Vout 5.0V 3.3V 2.5V 1.8V 1.2V 70 60 50 40 0 2 4 6 8 0 10 2 4 6 8 10 OUTPUT CURRENT (A) OUTPUT CURRENT (A) Figure 3 - Safe Operating Area Vin = 12 V, Output Voltage = 1.8 V (See Note A) Figure 4 - Efficiency vs Load Current Vin = 12 V (See Note B) Track Margin Down Margin Up Notes 10 9 8 1 A 7 B PTH12060 (Top View) Vin 3 Inhibit + Vout 6 2 Cin 560F (Required) 4 5 Vo Sense RSET 1%, 0.1W (Required) Co1 330F (Optional) + Co2 Ceramic (Optional) GND GND Figure 5 - Standard Application - All Models L O A D SOA curves represent the conditions at which internal components are within the Emerson Network Power derating guidelines. Characteristic data has been developed from actual products tested at 25 C. This data is considered typical data for the converter. Embedded Power for Business-Critical Continuity Rev.3.12.09_170 Rev.mm.dd.yy short titlePTH12060 of product of 6x PTH12060L Characteristic Data 100 80 90 70 60 EFFICIENCY (%) TEMPERATURE (C) 90 Nat Conv 100 LFM 50 40 30 20 0 2 4 6 8 70 60 50 10 Vout 1.8V 1.5V 1.2V 1.0V 0.8V 80 OUTPUT CURRENT (A) 0 2 4 6 8 10 OUTPUT CURRENT (A) Figure 7 - Efficiency vs Load Current Vin = 12 V (See Note B) Figure 6 - Safe Operating Area Vin = 12 V, Output Voltage = 1.8 V (See Note A) Track Margin Down Margin Up 10 9 8 1 7 Notes PTH12060 (Top View) Vin 3 Inhibit + Vout 6 2 Cin 560F (Required) 4 5 A B Vo Sense RSET 1%, 0.1W (Required) Co1 330F (Optional) + L Co2 O Ceramic A (Optional) D GND GND Figure 8 - Standard Application - All Models SOA curves represent the conditions at which internal components are within the Emerson Network Power derating guidelines. Characteristic data has been developed from actual products tested at 25 C. This data is considered typical data for the converter. Embedded Power for Business-Critical Continuity Mechanical Drawings Americas 0.140 (3.55) 0.995 (25.27) 0.125 (3.18) 0.125 (3.18) 0.060 (1.52) 1 0.060 (1.52) 0.250 (6.35) 0.375 (9.52) 9 10 8 o0.040 (1.02) 5 Places. 7 0.070 (1.78) (Standoff Shoulder) 0.620 0.500 (12.70) (15.75) 2 3 4 5 Lowest Component 0.010 min. (0.25) Bottom side Clearance Rev.3.12.09_170 PTH12060 of 6 5810 Van Allen Way Carlsbad, CA 92008 USA Telephone: +1 760 930 4600 Facsimile: +1 760 930 0698 Europe (UK) Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX United Kingdom Telephone: +44 (0) 1384 842 211 Facsimile: +44 (0) 1384 843 355 Asia (HK) 6 TOP VIEW Host Board 0.354 (9.00) MAX. Dimensions in Inches (mm) Tolerances (unless otherwise specified) 2 Places 0.030 (0.76) 3 Places 0.010 (0.25) SIDE VIEW 14/F, Lu Plaza 2 Wing Yip Street Kwun Tong, Kowloon Hong Kong Telephone: +852 2176 3333 Facsimile: +852 2176 3888 For global contact, visit: Figure 9 - Plated Through-Hole www.PowerConversion.com techsupport.embeddedpower @emerson.com 0.995 (25.27) 0.125 (3.18) 0.125 (3.18) 0.375 (9.52) 0.060 (1.52) 1 9 10 8 0.354 (9.00) max.* 0.060 (1.52) 0.250 (6.35) 7 *After solder reflow on customer board Solder Ball 0.040 (1.02) 10 Places 0.500 0.620 (12.70) (15.75) While every precaution has been taken to ensure accuracy and completeness in this literature, Emerson Network Power assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. Emerson Network Power. The global leader in enabling business-critical continuity. AC Power Connectivity 2 3 4 5 DC Power 6 Embedded Computing SIDE VIEW TOP VIEW Embedded Power Monitoring Dimensions in Inches (mm) Tolerances (unless otherwise specified) 2 Places 0.030 (0.76) 3 Places 0.010 (0.25) Outside Plant Power Switching & Controls Figure 10 - Surface-Mount Pin Connections Pin Connections cont. Pin No. Function Pin No. Function Pin 1 Ground Pin 6 Vout Pin 2 Vin Pin 7 Ground Pin 3 Inhibit* Pin 8 Track Pin 4 Vo adjust Pin 9 Margin down* Pin 5 Vo sense Pin 10 Margin up* *Denotes negative logic: Open = Normal operation Ground = Function active Precision Cooling Racks & Integrated Cabinets Services Surge Protection EmersonNetworkPower.com Emerson Network Power and the Emerson Network Power logo are trademarks and service marks of Emerson Electric Co. (c)2008 Emerson Electric Co.